Ford 2014 F 150 Owners Manual

2014-Ford-Ford-F-150-Owners-Manual-version-3_om_EN-US_03_2014 2014 Ford F-150 Maintenance Schedule | SERVICE MANUAL OWNERS

2015-10-23

: Ford Ford-2014-Ford-F-150-Owners-Manual-815503 ford-2014-ford-f-150-owners-manual-815503 ford pdf

Open the PDF directly: View PDF .
Page Count: 472

Download
Open PDF In Browser	View PDF

2014 F-150 Owner’s Manual

EL3J 19A321 AA

2014 F-150 Owner’s Manual

fordowner.com

ford.ca

March 2014

Third Printing

Owner’s Manual

F-150

Litho in U.S.A.

The information contained in this publication was correct at the time of going to print. In the interest of
continuous development, we reserve the right to change specifications, design or equipment at any time
without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a
retrieval system or translated into any language in any form by any means without our written permission.
Errors and omissions excepted.
© Ford Motor Company 2014
All rights reserved.
Part Number: 20140214211023

Table of Contents
Safety Canopy™............................................46
Crash Sensors and Airbag Indicator.......48
Airbag Disposal..............................................48

Introduction
About This Manual...........................................7
Symbols Glossary.............................................7
Data Recording..................................................9
California Proposition 65..............................11
Perchlorate.........................................................11
Ford Credit..........................................................11
Replacement Parts
Recommendation........................................11
Special Notices................................................12
Mobile Communications
Equipment.....................................................12
Export Unique Options..................................13

Keys and Remote Controls
General Information on Radio
Frequencies.................................................49
Remote Control..............................................49
Replacing a Lost Key or Remote
Control............................................................52

MyKey™
Principle of Operation..................................53
Creating a MyKey............................................53
Clearing All MyKeys.......................................55
Checking MyKey System Status...............55
Using MyKey With Remote Start
Systems.........................................................55
MyKey Troubleshooting...............................56

Child Safety
General Information.......................................14
Installing Child Seats.....................................15
Booster Seats..................................................24
Child Seat Positioning..................................26
Child Safety Locks.........................................28

Locks
Locking and Unlocking.................................57
Keyless Entry...................................................58

Safety Belts
Principle of Operation..................................30
Fastening the Safety Belts...........................31
Safety Belt Height Adjustment.................34
Safety Belt Warning Lamp and Indicator
Chime.............................................................34
Safety Belt Minder.........................................35
Child Restraint and Safety Belt
Maintenance................................................37

Security
Passive Anti-Theft System..........................61
Anti-Theft Alarm............................................62

Power Running Boards
Using Power Running Boards....................63

Personal Safety System™

Steering Wheel

Personal Safety System™..........................38

Adjusting the Steering Wheel...................65
Audio Control..................................................66
Voice Control....................................................67
Cruise Control..................................................67
Information Display Control.......................67

Supplementary Restraints
System
Principle of Operation..................................39
Driver and Passenger Airbags...................40
Front Passenger Sensing System.............41
Side Airbags.....................................................45

Pedals
Adjusting the Pedals....................................68

F150 (TF6) , enUSA

Table of Contents
Wipers and Washers

Seats

Windshield Wipers........................................69
Autowipers.......................................................69
Windshield Washers.....................................70

Sitting in the Correct Position...................114
Head Restraints..............................................114
Manual Seats..................................................116
Power Seats.....................................................117
Memory Function..........................................118
Rear Seats........................................................119
Heated Seats.................................................120
Ventilated Seats.............................................121
Front Seat Armrest.......................................122
Rear Seat Armrest........................................123

Lighting
Lighting Control................................................71
Autolamps..........................................................71
Instrument Lighting Dimmer......................72
Daytime Running Lamps.............................72
Front Fog Lamps.............................................72
Direction Indicators........................................73
Interior Lamps..................................................73

Universal Garage Door
Opener

Windows and Mirrors

Universal Garage Door Opener...............124

Power Windows..............................................75
Exterior Mirrors................................................76
Interior Mirror....................................................78
Sun Visors.........................................................79
Moonroof...........................................................79

Auxiliary Power Points
Auxiliary Power Points................................132

Storage Compartments

Instrument Cluster

Center Console..............................................134
Overhead Console........................................134

Gauges................................................................81
Warning Lamps and Indicators.................82
Audible Warnings and Indicators.............85

Starting and Stopping the
Engine

General Information......................................87
Information Messages.................................98

General Information....................................135
Ignition Switch...............................................135
Starting a Gasoline Engine........................135
Engine Block Heater.....................................137

Climate Control

Fuel and Refueling

Manual Climate Control............................106
Manual Climate Control.............................107
Automatic Climate Control......................109
Hints on Controlling the Interior
Climate..........................................................110
Heated Windows and Mirrors....................112
Remote Start...................................................113

Safety Precautions......................................139
Fuel Quality....................................................140
Running Out of Fuel......................................141
Refueling..........................................................142
Fuel Consumption........................................143
Emission Control System..........................144

Information Displays

F150 (TF6) , enUSA

Table of Contents
Transmission

Load Carrying

Automatic Transmission............................147

Load Limit........................................................179
Tailgate.............................................................186

Four-Wheel Drive
Towing

Using Four-Wheel Drive.............................153

Towing a Trailer..............................................191
Trailer Sway Control....................................192
Recommended Towing Weights............192
Essential Towing Checks...........................201
Transporting the Vehicle...........................207
Towing the Vehicle on Four Wheels......208

Rear Axle
Limited Slip Differential..............................161
Electronic Locking Differential.................161

Brakes
General Information....................................163
Hints on Driving With Anti-Lock
Brakes...........................................................163
Parking Brake.................................................164
Hill Start Assist..............................................164

Driving Hints
Breaking-In......................................................210
Economical Driving......................................210
Driving Through Water.................................211
Floor Mats.........................................................211
Snowplowing..................................................212

Traction Control
Principle of Operation................................166
Using Traction Control...............................166

Roadside Emergencies
Roadside Assistance...................................215
Hazard Warning Flashers..........................216
Fuel Shutoff....................................................216
Jump Starting the Vehicle.........................216
Post-Crash Alert System...........................218

Stability Control
Principle of Operation.................................167
Using Stability Control...............................168

Terrain Response
Principle of Operation.................................170
Using Hill Descent Control........................170

Customer Assistance
Getting the Services You Need................219
In California (U.S. Only)............................220
The Better Business Bureau (BBB) Auto
Line Program (U.S. Only).......................221
Utilizing the Mediation/Arbitration
Program (Canada Only)........................221
Getting Assistance Outside the U.S. and
Canada........................................................222
Ordering Additional Owner's
Literature.....................................................223
Reporting Safety Defects (U.S.
Only).............................................................223
Reporting Safety Defects (Canada
Only).............................................................224

Parking Aids
Parking Aid.......................................................172
Rear View Camera........................................173

Cruise Control
Principle of Operation.................................176
Using Cruise Control....................................176

Driving Aids
Steering.............................................................177

F150 (TF6) , enUSA

Table of Contents
Cleaning the Windows and Wiper
Blades...........................................................261
Cleaning the Interior....................................261
Cleaning the Instrument Panel and
Instrument Cluster Lens........................261
Cleaning Leather Seats.............................262
Repairing Minor Paint Damage..............263
Cleaning the Alloy Wheels.......................264
Vehicle Storage............................................264

Fuses
Fuse Specification Chart...........................225
Changing a Fuse...........................................233

Maintenance
General Information...................................235
Opening and Closing the Hood..............235
Under Hood Overview - 3.5L
Ecoboost™................................................236
Under Hood Overview - 3.7L....................237
Under Hood Overview - 5.0L..................238
Under Hood Overview - 6.2L...................239
Engine Oil Dipstick......................................240
Engine Oil Check..........................................240
Engine Coolant Check................................241
Automatic Transmission Fluid
Check...........................................................245
Transfer Case Fluid Check........................245
Brake Fluid Check........................................246
Power Steering Fluid Check....................246
Washer Fluid Check....................................246
Fuel Filter........................................................246
Changing the 12V Battery.........................246
Checking the Wiper Blades.....................249
Changing the Wiper Blades.....................249
Adjusting the Headlamps........................249
Removing a Headlamp...............................251
Changing a Bulb...........................................252
Bulb Specification Chart...........................254
Changing the Engine Air Filter - 3.5L
Ecoboost™................................................256
Changing the Engine Air Filter - 3.7L/
5.0L/6.2L.....................................................257

Wheels and Tires
General Information...................................266
Tire Care..........................................................268
Using Snow Chains.....................................283
Tire Pressure Monitoring System...........283
Changing a Road Wheel...........................289
Technical Specifications...........................294

Capacities and Specifications
Engine Specifications................................296
Motorcraft Parts..........................................298
Vehicle Identification Number...............298
Vehicle Certification Label.......................299
Transmission Code Designation...........300
Technical Specifications............................301

Audio System
General Information...................................306
Audio unit - Vehicles With: AM/FM.......307
Audio unit - Vehicles With: AM/FM/CD/
SYNC/Satellite Radio...........................308
Audio unit - Vehicles With: AM/FM/CD/
SYNC/Satellite Radio.............................312
Audio unit - Vehicles With: Sony AM/FM/
CD...................................................................315
Digital Radio...................................................316
Satellite Radio...............................................318
Audio Input Jack............................................321
USB Port..........................................................322
Media Hub......................................................322

Vehicle Care
General Information...................................259
Cleaning Products.......................................259
Cleaning the Exterior..................................259
Waxing............................................................260
Cleaning the Engine...................................260

F150 (TF6) , enUSA

Table of Contents
SYNC™
General Information...................................323
Using Voice Recognition...........................325
Using SYNC™ With Your Phone.............327
SYNC™ Applications and Services......338
Using SYNC™ With Your Media
Player...........................................................345
SYNC™ Troubleshooting.........................353

MyFord Touch™
General Information...................................359
Settings...........................................................366
Entertainment...............................................376
Phone...............................................................393
Information....................................................399
Climate...........................................................408
Navigation.......................................................410

Accessories
Accessories.....................................................419

Appendices
End User License Agreement...................421

Extended Service Plan
(ESP)
Extended Service Plan (ESP).................436

Scheduled Maintenance
General Maintenance Information.......438
Normal Scheduled Maintenance...........441
Special Operating Conditions Scheduled
Maintenance.............................................446
Scheduled Maintenance Record............451

F150 (TF6) , enUSA

Introduction
ABOUT THIS MANUAL
Thank you for choosing Ford. We
recommend that you take some time to
get to know your vehicle by reading this
manual. The more that you know about it,
the greater the safety and pleasure you
will get from driving it.
WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any handheld device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

E154903

Right-hand side

Left-hand side

Protecting the Environment
You must play your part in protecting the
environment. Correct vehicle usage and
the authorized disposal of waste, cleaning
and lubrication materials are significant
steps toward this aim.

Note: This manual describes product
features and options available throughout
the range of available models, sometimes
even before they are generally available. It
may describe options not fitted to your
vehicle.

SYMBOLS GLOSSARY
These are some of the symbols you may
see on your vehicle.
Safety alert

Note: Some of the illustrations in this
manual may be used for different models,
so may appear different to you on your
vehicle. However, the essential information
in the illustrations is always correct.

See Owner's Manual

Air conditioning system

Note: Always use and operate your vehicle
in line with all applicable laws and
regulations.

E162384

Anti-lock braking system

Note: Pass on this manual when selling
your vehicle. It is an integral part of the
vehicle.

Avoid smoking, flames or sparks

This manual may qualify the location of a
component as left-hand side or right-hand
side. The side is determined when facing
forward in the seat.

F150 (TF6) , enUSA

Introduction
Battery

Engine oil

Battery acid

Explosive gas

Brake fluid - non petroleum
based

Fan warning

Brake system

Fasten safety belt

Cabin air filter

Front airbag

Check fuel cap

Front fog lamps

Child safety door lock or unlock

Fuel pump reset

Child seat lower anchor

Fuse compartment

Child seat tether anchor

Hazard warning flashers

Cruise control

Heated rear window

Do not open when hot

Heated windshield

E71340

E91392

Engine air filter

Interior luggage compartment
release

Engine coolant

Jack

Engine coolant temperature

Keep out of reach of children
E161353

Lighting control

F150 (TF6) , enUSA

Introduction
Low tire pressure warning

DATA RECORDING
Service Data Recording

Maintain correct fluid level

Service data recorders in your vehicle are
capable of collecting and storing
diagnostic information about your vehicle.
This potentially includes information about
the performance or status of various
systems and modules in the vehicle, such
as engine, throttle, steering or brake
systems. In order to properly diagnose and
service your vehicle, Ford Motor Company,
Ford of Canada, and service and repair
facilities may access or share among them
vehicle diagnostic information received
through a direct connection to your vehicle
when diagnosing or servicing your vehicle.
Additionally, when your vehicle is in for
service or repair, Ford Motor Company,
Ford of Canada, and service and repair
facilities may access or share among them
data for vehicle improvement purposes.
For U.S. only (if equipped), if you choose
to use the SYNC Vehicle Health Report,
you consent that certain diagnostic
information may also be accessed
electronically by Ford Motor Company and
Ford authorized service facilities, and that
the diagnostic information may be used
for any purpose. See SYNC™ (page 323).

Note operating instructions

Panic alarm

Parking aid
E139213

Parking brake

Power steering fluid

Power windows front/rear

Power window lockout

Service engine soon

Event Data Recording
Side airbag

This vehicle is equipped with an event
data recorder. The main purpose of an
event data recorder is to record, in
certain crash or near crash-like
situations, such as an airbag
deployment or hitting a road obstacle;
this data will assist in understanding
how a vehicle’s systems performed.
The event data recorder is designed to
record data related to vehicle dynamics
and safety systems for a short period
of time, typically 30 seconds or less.

Shield the eyes
E167012

Stability control

Windshield wash and wipe

F150 (TF6) , enUSA

Introduction
The event data recorder in this vehicle
is designed to record such data as:
• How various systems in your vehicle
were operating;
• Whether or not the driver and
passenger safety belts were
buckled/fastened;
• How far (if at all) the driver was
depressing the accelerator and/or
the brake pedal; and
• How fast the vehicle was traveling;
and
• Where the driver was positioning
the steering wheel.

or where required by law enforcement,
other government authorities or other
third parties acting with lawful
authority. Other parties may seek to
access the information independently
of Ford Motor Company and Ford of
Canada.
Note: Including to the extent that any
law pertaining to Event Data Recorders
applies to SYNC or its features, please
note the following: Once 911 Assist (if
equipped) is enabled (set ON), 911 Assist
may, through any paired and connected
cell phone, disclose to emergency
services that the vehicle has been in a
crash involving the deployment of an
airbag or, in certain vehicles, the
activation of the fuel pump shut-off.
Certain versions or updates to 911 Assist
may also be capable of being used to
electronically or verbally provide to 911
operators the vehicle location (such as
latitude and longitude), and/or other
details about the vehicle or crash or
personal information about the
occupants to assist 911 operators to
provide the most appropriate emergency
services. If you do not want to disclose
this information, do not activate the 911
Assist feature. See SYNC™ (page 323).

This data can help provide a better
understanding of the circumstances in
which crashes and injuries occur.
Note: Event data recorder data is
recorded by your vehicle only if a
non-trivial crash situation occurs; no data
is recorded by the event data recorder
under normal driving conditions and no
personal data or information (e.g., name,
gender, age, and crash location) is
recorded (see limitations regarding 911
Assist and Traffic, directions and
Information privacy below). However,
parties, such as law enforcement, could
combine the event data recorder data
with the type of personally identifying
data routinely acquired during a crash
investigation.

Additionally, when you connect to
Traffic, Directions and Information (if
equipped, U.S. only), the service uses
GPS technology and advanced vehicle
sensors to collect the vehicle’s current
location, travel direction, and speed
(“vehicle travel information”), only to
help provide you with the directions,
traffic reports, or business searches
that you request. If you do not want
Ford or its vendors to receive this
information, do not activate the
service. For more information, see
Traffic, Directions and Information,
Terms and Conditions. See SYNC™
(page 323).

To read data recorded by an event data
recorder, special equipment is required,
and access to the vehicle or the event
data recorder is needed. In addition to
the vehicle manufacturer, other
parties, such as law enforcement, that
have such special equipment, can read
the information if they have access to
the vehicle or the event data recorder.
Ford Motor Company and Ford of
Canada do not access event data
recorder information without obtaining
consent, unless pursuant to court order

F150 (TF6) , enUSA

Introduction
REPLACEMENT PARTS
RECOMMENDATION

CALIFORNIA PROPOSITION 65
WARNING

Your vehicle has been built to the highest
standards using quality parts. We
recommend that you demand the use of
genuine Ford and Motorcraft parts
whenever your vehicle requires scheduled
maintenance or repair. You can clearly
identify genuine Ford and Motorcraft parts
by looking for the Ford, FoMoCo or
Motorcraft branding on the parts or their
packaging.

Some constituents of engine
exhaust, certain vehicle components,
certain fluids contained in vehicles
and certain products of component wear
contain or emit chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.

PERCHLORATE

Scheduled Maintenance and
Mechanical Repairs

Certain components in your vehicle such
as airbag modules, safety belt
pretensioners and remote control batteries
may contain perchlorate material. Special
handling may apply for service or vehicle
end of life disposal. For more information
visit:

One of the best ways for you to make sure
that your vehicle provides years of service
is to have it maintained in line with our
recommendations using parts that
conform to the specifications detailed in
this Owner’s Manual. Genuine Ford and
Motorcraft parts meet or exceed these
specifications.

Web Address

www.dtsc.ca.gov/hazardouswaste/
perchlorate

Collision Repairs
We hope that you never experience a
collision, but accidents do happen. Genuine
Ford replacement collision parts meet our
stringent requirements for fit, finish,
structural integrity, corrosion protection
and dent resistance. During vehicle
development we validate these parts
deliver the intended level of protection as
a whole system. A great way to know for
sure you are getting this level of protection
is to use genuine Ford replacement
collision parts.

FORD CREDIT
(U.S. Only)
Ford Credit offers a full range of financing
and lease plans to help you acquire your
vehicle. If you have financed or leased your
vehicle through Ford Credit, thank you for
your business.
For your convenience we offer a number
of ways to contact us, as well as help
manage your account.
Phone: 1-800-727-7000
For more information regarding Ford Credit,
as well as access Account Manager, please
go to www.fordcredit.com.

F150 (TF6) , enUSA

Introduction
Warranty on Replacement Parts

Before you drive your vehicle, please read
this Owner’s Manual carefully. Your vehicle
is not a passenger car. As with other
vehicles of this type, failure to operate your
vehicle correctly may result in loss of
vehicle control, vehicle rollover, personal
injury or death.

Genuine Ford and Motorcraft replacement
parts are the only replacement parts that
benefit from a Ford Warranty. Damage
caused to your vehicle as a result of the
failure of non-Ford parts may not be
covered by the Ford Warranty. For
additional information, refer to the terms
and conditions of the Ford Warranty.

Using your vehicle with a snowplow
See Snowplowing (page 212).

SPECIAL NOTICES

Using your vehicle as an ambulance

New Vehicle Limited Warranty

Do not use this vehicle as an ambulance.
Your vehicle is not equipped with the Ford
Ambulance Preparation Package.

For a detailed description of what is
covered and what is not covered by your
vehicle’s New Vehicle Limited Warranty,
refer to the Warranty Manual that is
provided to you along with your Owner’s
Manual.

MOBILE COMMUNICATIONS
EQUIPMENT
Using mobile communications equipment
is becoming increasingly important in the
conduct of business and personal affairs.
However, you must not compromise your
own or others’ safety when using such
equipment. Mobile communications can
enhance personal safety and security when
appropriately used, particularly in
emergency situations. Safety must be
paramount when using mobile
communications equipment to avoid
negating these benefits. Mobile
communication equipment includes, but
is not limited to, cellular phones, pagers,
portable email devices, text messaging
devices and portable two-way radios.

Special Instructions
For your added safety, your vehicle is fitted
with sophisticated electronic controls.
WARNINGS
Failure to follow the specific
warnings and instructions could
result in personal injury. See
Supplementary Restraints System
(page 39).
Front seat mounted rear-facing child
or infant seats should NEVER be
placed in front of an active
passenger airbag.
Notice to owners of pickup trucks and
utility type vehicles
WARNING
Utility vehicles have a significantly
higher rollover rate than other types
of vehicles.

F150 (TF6) , enUSA

Introduction
WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any hand-held device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

EXPORT UNIQUE OPTIONS
For your particular global region, your
vehicle may be equipped with features and
options that are different from the features
and options that are described in this
Owner’s Manual. A market unique
supplement may be supplied that
complements this book. By referring to the
market unique supplement, if provided,
you can properly identify those features,
recommendations and specifications that
are unique to your vehicle. This Owner’s
Manual is written primarily for the U.S. and
Canadian Markets. Features or equipment
listed as standard may be different on units
built for Export. Refer to this Owner’s
Manual for all other required
information and warnings.

F150 (TF6) , enUSA

Child Safety
GENERAL INFORMATION

WARNINGS
requirements of law. Ford recommends
checking with a NHTSA Certified Child
Passenger Safety Technician (CPST) and
consult your pediatrician to make sure your
child seat is appropriate for your child, and
is compatible with and properly installed
in your vehicle. To locate a child seat fitting
station and CPST, contact the NHTSA toll
free at 1-888-327-4236 or go to
http://www.nhtsa.dot.gov. In Canada,
check with your local St. John Ambulance
office for referral to a CPST or for further
information, contact your provincial
ministry of transportation, locate your local
St. John Ambulance office by searching for
St. John Ambulance on the internet, or
Transport Canada at 1-800-333-0371
(http://www.tc.gc.ca). Failure to properly
restrain children in safety seats made
especially for their height, age, and weight
may result in an increased risk of serious
injury or death to your child.

See the following sections for directions
on how to properly use safety restraints
for children.
WARNINGS
Always make sure your child is
secured properly in a device that is
appropriate for their height, age and
weight. Child safety restraints must be
bought separately from your vehicle.
Failure to follow these instructions and
guidelines may result in an increased risk
of serious injury or death to your child.
All children are shaped differently.
The recommendations for safety
restraints are based on probable
child height, age and weight thresholds
from National Highway Traffic Safety
Administration and other safety
organizations, or are the minimum

F150 (TF6) , enUSA

Child Safety
Recommendations for Safety Restraints for Children
Child

Child size, height, weight, or age

Recommended restraint
type

Infants or
toddlers

Children weighing 40 lb (18 kg) or less
(generally age four or younger).

Use a child safety seat
(sometimes called an
infant carrier, convertible
seat, or toddler seat).

Small children

Children who have outgrown or no longer
properly fit in a child safety seat (generally children who are less than 4 ft. 9 in.
(1.45 m) tall, are greater than age four
and less than age 12, and between 40 lb
(18 kg) and 80 lb (36 kg) and upward to
100 lb (45 kg) if recommended by your
child restraint manufacturer).

Use a belt-positioning
booster seat.

Larger children Children who have outgrown or no longer
properly fit in a belt-positioning booster
seat (generally children who are at least
4 ft. 9 in. (1.45 m) tall or greater than 80
lb (36 kg) or 100 lb (45 kg) if recommended by child restraint manufacturer).

•

You are required by law to properly use
safety seats for infants and toddlers in
the United States and Canada.
Many states and provinces require that
small children use approved booster
seats until they reach age eight, a
height of 4 feet 9 inches (1.45 meters)
tall, or 80 pounds (36 kilograms).
Check your local and state or provincial
laws for specific requirements about
the safety of children in your vehicle.
When possible, always properly
restrain children 12 years of age and
under in a rear seating position of your
vehicle. Accident statistics suggest that
children are safer when properly
restrained in the rear seating positions
than in a front seating position. See
Front Passenger Sensing System
(page 41).

INSTALLING CHILD SEATS
Child Seats

E142594

F150 (TF6) , enUSA

Use a vehicle safety belt
having the lap belt snug
and low across the hips,
shoulder belt centered
across the shoulder and
chest, and seat back
upright.

Child Safety
Use a child safety seat (sometimes called
an infant carrier, convertible seat, or
toddler seat) for infants, toddlers, or
children weighing 40 pounds (18
kilograms) or less (generally age four or
younger).

•

Using Lap and Shoulder Belts

Perform the following steps when
installing the child seat with combination
lap and shoulder belts:

•

WARNINGS
Airbags can kill or injure a child in a
child seat. Never place a rear-facing
child seat in front of an active airbag.
If you must use a forward-facing child seat
in the front seat, move the vehicle seat
upon which the seat is installed all the way
back.

Place the vehicle seat upon which the
child seat will be installed in the upright
position.
Put the safety belt in the automatic
locking mode. This vehicle does not
require the use of a locking clip.

Note: Although the child seat illustrated is
a forward facing child seat, the steps are
the same for installing a rear facing child
seat.

Airbags can kill or injure a child in a
child seat. Children 12 and under
should be properly restrained in the
rear seat whenever possible.
Depending on where you secure a
child restraint, and depending on the
child restraint design, you may block
access to certain safety belt buckle
assemblies and LATCH lower anchors,
rendering those features potentially
unusable. To avoid risk of injury, occupants
should only use seating positions where
they are able to be properly restrained.

E142528

When installing a child safety seat with
combination lap and shoulder belts:
• Use the correct safety belt buckle for
that seating position.
• Insert the belt tongue into the proper
buckle until you hear a snap and feel it
latch. Make sure the tongue is securely
fastened in the buckle.
• Keep the buckle release button
pointing up and away from the safety
seat, with the tongue between the child
seat and the release button, to prevent
accidental unbuckling.

E142529

2. Pull down on the shoulder belt and
then grasp the shoulder belt and lap
belt together.

F150 (TF6) , enUSA

Position the child safety seat in a seat
with a combination lap and shoulder
belt.

Child Safety

E142530

E142875

3. While holding the shoulder and lap belt
portions together, route the tongue
through the child seat according to the
child seat manufacturer's instructions.
Be sure the belt webbing is not twisted.

5. To put the retractor in the automatic
locking mode, grasp the shoulder
portion of the belt and pull downward
until all of the belt is pulled out.
Note: The automatic locking mode is
available on the front passenger and rear
seats. This vehicle does not require the use
of a locking clip.
6. Allow the belt to retract to remove
slack. The belt will click as it retracts
to indicate it is in the automatic locking
mode.
7. Try to pull the belt out of the retractor
to make sure the retractor is in the
automatic locking mode (you should
not be able to pull more belt out). If the
retractor is not locked, unbuckle the
belt and repeat Steps 5 and 6.

E142531

4. Insert the belt tongue into the proper
buckle (the buckle closest to the
direction the tongue is coming from)
for that seating position until you hear
a snap and feel the latch engage. Make
sure the tongue is latched securely by
pulling on it.

E142533

F150 (TF6) , enUSA

Child Safety
Using Lap and Shoulder Belts
(Front Center Seating Position)

8. Remove remaining slack from the belt.
Force the seat down with extra weight,
for example, by pressing down or
kneeling on the child restraint while
pulling up on the shoulder belt in order
to force slack from the belt. This is
necessary to remove the remaining
slack that will exist once the extra
weight of the child is added to the child
restraint. It also helps to achieve the
proper snugness of the child seat to
your vehicle. Sometimes, a slight lean
toward the buckle will help to remove
remaining slack from the belt.
9. Attach the tether strap (if the child seat
is equipped).

WARNINGS
Airbags can kill or injure a child in a
child seat. If you must use a
forward-facing child seat in the front
seat, move the vehicle seat upon which
the seat is installed all the way back.
Rear facing child seats should never
be placed in front of an active airbag.
Always use both lap and shoulder
safety belt in the center seating
position.
The belt webbing below the tongue is the
lap portion of the combination lap and
shoulder belt, and the belt webbing above
the tongue is the shoulder belt portion of
the combination lap and shoulder belt.

E142534

10.

Before placing the child in the seat,
forcibly move the seat forward and
back to make sure the seat is securely
held in place.
E142528

To check this, grab the seat at the belt path
and attempt to move it side to side and
forward and back. There should be no
more than 1 inch (2.5 centimeters) of
movement for proper installation.

Ford recommends checking with a NHTSA
Certified Child Passenger Safety
Technician to make certain the child
restraint is properly installed. In Canada,
check with your local St. John Ambulance
office for referral to a Certified Passenger
Seat Technician.

F150 (TF6) , enUSA

Position the child safety seat in the
front center seat.

Child Safety
4. Insert the belt tongue into the proper
buckle (the buckle closest to the
direction the tongue is coming from)
for that seating position until you hear
a snap and feel the latch engage. Make
sure the tongue is latched securely by
pulling on it.

E162708

2. Slide the tongue up the webbing.

E142533

5. While pushing down with your knee on
the child seat pull up on the shoulder
belt portion to tighten the lap belt
portion of the combination lap and
shoulder belt.
6. Allow the safety belt to retract and
remove any slack in the belt to securely
tighten the child safety seat in the
vehicle.
7. Attach the tether strap (if the child seat
is equipped).

E142530

3. While holding both shoulder and lap
portions next to the tongue, route the
tongue and webbing through the child
seat according to the child seat
manufacturer's instructions. Be sure
that the belt webbing is not twisted.

E142534
E142531

F150 (TF6) , enUSA

Child Safety
8. Before placing the child in the seat,
forcibly move the seat forward and
back to make sure the seat is securely
held in place. To check this, grab the
seat at the belt path and attempt to
move it side to side and forward and
back. There should be no more than 1
inch (2.5 centimeters) of movement
for proper installation.
9. Check from time to time to be sure that
there is no slack in the lap and shoulder
belt. The shoulder belt must be snug
to keep the lap belt tight during a crash.

WARNINGS
Depending on where you secure a
child restraint, and depending on the
child restraint design, you may block
access to certain safety belt buckle
assemblies or LATCH lower anchors,
rendering those features potentially
unusable. To avoid risk of injury, occupants
should only use seating positions where
they are able to be properly restrained.
The LATCH system is composed of three
vehicle anchor points: two lower anchors
located where the vehicle seat back and
seat cushion meet (called the seat bight)
and one top tether anchor located behind
that seating position.

LATCH compatible child safety seats have
two rigid or webbing mounted
attachments that connect to the two lower
anchors at the LATCH equipped seating
positions in your vehicle. This type of
attachment method eliminates the need
to use safety belts to attach the child seat,
however the safety belt can still be used
to attach the child seat if the lower anchors
are not used. For forward-facing child
seats, the top tether strap must also be
attached to the proper top tether anchor,
if a top tether strap has been provided with
your child seat.

Using Lower Anchors and Tethers
for CHildren (LATCH)
WARNINGS
Never attach two child safety seats
to the same anchor. In a crash, one
anchor may not be strong enough to
hold two child safety seat attachments
and may break, causing serious injury or
death.

Your vehicle is equipped with LATCH lower
anchors for child seat installation at the
following seating positions (LATCH is not
available on F150 Regular Cab):

F150 (TF6) , enUSA

Child Safety
SuperCab and SuperCrew

E166694

Use of Inboard Lower Anchors
from the Outboard Seating
Positions (Center Seating Use)
WARNING
The standardized spacing for LATCH
lower anchors is 11 inches (280
millimeters) center to center. Do not
use LATCH lower anchors for the center
seating position unless the child seat
manufacturer's instructions permit and
specify using anchors spaced at least as
far apart as those in this vehicle.

E166695

The lower LATCH anchors are located at
the rear section of the rear seat between
the cushion and seatback. Follow the child
seat manufacturer's instructions to
properly install a child seat with LATCH
attachments.

The lower anchors at the center of the
second row rear seat are spaced 25.7
inches (652 millimeters) apart. The
standardized spacing for LATCH lower
anchors is 11 inches (280 millimeters)
center to center. A child seat with rigid
LATCH attachments cannot be installed
at the center seating position. LATCH
compatible child seats (with attachments
on belt webbing) can only be used at this
seating position provided that the child
seat manufacturer's instructions permit
use with the anchor spacing stated. Do not
attach a child seat to any lower anchor if
an adjacent child seat is attached to that
anchor.

Follow the instructions later in this chapter
on attaching child safety seats with tether
straps.
Attach LATCH lower attachments of the
child seat only to the anchors shown.

F150 (TF6) , enUSA

Child Safety
Each time you use the safety seat, check
that the seat is properly attached to the
lower anchors and tether anchor, if
applicable. Tug the child seat from side to
side and forward and back where it is
secured to the vehicle. The seat should
move less than one inch when you do this
for a proper installation.

Contact the manufacturer of your child
seat for information about ordering a
tether strap, or to obtain a longer tether
strap if the tether strap on your safety seat
does not reach the appropriate top tether
anchor in the vehicle.
The passenger seats of your vehicle may
be equipped with built-in tether strap
anchors located behind the seats as
described below.

If the safety seat is not anchored properly,
the risk of a child being injured in a crash
greatly increases.

The tether anchors in your vehicle may be
loops of webbing above the seatback or
an anchor bracket behind the seat on the
rear edge of the seat cushion.

Combining Safety Belt and LATCH
Lower Anchors for Attaching Child
Safety Seats

The rear seat in the SuperCab and
SuperCrew has three straps along the top
of the seat back that function as both
routing loops for the tether straps and
anchor loops.

When used in combination, either the
safety belt or the LATCH lower anchors
may be attached first, provided a proper
installation is achieved. Attach the tether
strap afterward, if included with the child
seat.

The tether strap anchors in your vehicle
are in the following positions (shown from
top view):

Using Tether Straps

Regular Cab

Many forward-facing child safety seats
include a tether strap which extends from
the back of the child safety seat and hooks
to an anchoring point called the top tether
anchor. Tether straps are available as an
accessory for many older safety seats.

E166696

SuperCrew and SuperCab

E166697

F150 (TF6) , enUSA

Child Safety
Attach the tether strap only to the
appropriate tether anchor as shown. The
tether strap may not work properly if
attached somewhere other than the
correct tether anchor.

Regular Cab passenger and center
seats (located on back panel)

If you install a child seat with rigid LATCH
attachments, do not tighten the tether
strap enough to lift the child seat off the
vehicle seat cushion when the child is
seated in it. Keep the tether strap just snug
without lifting the front of the child seat.
Keeping the child seat just touching the
vehicle seat gives the best protection in a
severe crash.

E166698

If the tether strap is clipped incorrectly, the
child safety seat may not be retained
properly in the event of a crash.

Once the child safety seat has been
installed using either the safety belt, the
lower anchors of the LATCH system, or
both, you can attach the top tether strap.

4. Tighten the child safety seat tether strap
according to the manufacturer's
instructions.

Front Seat Tether Strap
Attachment (Regular Cab)

If the safety seat is not anchored properly,
the risk of a child being injured in a crash
greatly increases.

Route the child safety seat tether strap
over the back of the seat and under the
head restraint.
Note: For vehicles with adjustable head
restraints, route the tether strap under the
head restraint and between the head
restraint posts, otherwise route the tether
strap over the top of the seat back.

If your child restraint system is equipped
with a tether strap, and the child restraint
manufacturer recommends its use, Ford
also recommends its use.

Rear Seat Tether Strap
Attachment (SuperCab and
SuperCrew)

2. Locate the correct anchor for the
selected seating position. You may
need to pull the seat back forward to
access the tether anchors. Make sure
the seat is locked in the upright position
before installing the child seat.
3. Clip the tether strap to the anchor as
shown.

E167009

F150 (TF6) , enUSA

Child Safety
There are three loops of webbing just
above the back of the rear seat (along the
bottom edge of the rear window). Use
these loops as both routing loops and
anchor loops for up to three child safety
seat tether straps.

2. Route the tether strap behind the head
restraint supports to a loop behind an
adjacent seating position, and hook the
strap hook onto the loop. If using the
driver's side, pass the strap behind the
shoulder belt mounting for the center
seat. Always put the tether strap
through the routing loop. The head
restraint support post will hold the
child seat tightly, but the head restraint
post is not strong enough to hold the
child seat during a crash.
3. Tighten the tether strap according to
the child seat manufacturer's
instructions.

For example, the center loop can be used
as a routing loop for a child safety seat in
the center rear seat and as an anchoring
loop for child seats installed in the
outboard rear seats.
Many tether straps cannot be tightened if
the tether strap is hooked to the loop
directly behind the child seat. To provide
a tight tether strap:

If the safety seat is not anchored properly,
the risk of a child being injured in a crash
greatly increases.
If your child restraint system is equipped
with a tether strap, and the child restraint
manufacturer recommends its use, Ford
also recommends its use.

BOOSTER SEATS
WARNING

E162714

Never place, or allow a child to place,
the shoulder belt under a child's arm
or behind the back because it
reduces the protection for the upper part
of the body and may increase the risk of
injury or death in a crash.

Route the tether strap under the head
restraint and through the loop directly
behind the child seat.

Use a belt-positioning booster seat for
children who have outgrown or no longer
properly fit in a child safety seat (generally
children who are less than 4 feet 9 inches
(1.45 meters) tall, are greater than age four
(4) and less than age twelve (12), and
between 40 pounds (18 kilograms) and
80 pounds (36 kilograms) and upward to
100 pounds (45 kilograms) if

E162715

F150 (TF6) , enUSA

Child Safety
Types of Booster Seats

recommended by your child restraint
manufacturer). Many state and provincial
laws require that children use approved
booster seats until they reach age eight, a
height of 4 feet 9 inches (1.45 meters) tall,
or 80 pounds (36 kilograms).
Booster seats should be used until you can
answer YES to ALL of these questions
when seated without a booster seat:

E68924

•

E142595

•

•
•
•
•

Backless booster seats

If your backless booster seat has a
removable shield, remove the shield. If a
vehicle seating position has a low seat
back or no head restraint, a backless
booster seat may place your child's head
(as measured at the tops of the ears)
above the top of the seat. In this case,
move the backless booster to another
seating position with a higher seat back or
head restraint and lap and shoulder belts,
or consider using a high back booster seat.

Can the child sit all the way back
against their vehicle seat back with
knees bent comfortably at the edge of
the seat cushion?
Can the child sit without slouching?
Does the lap belt rest low across the
hips?
Is the shoulder belt centered on the
shoulder and chest?
Can the child stay seated like this for
the whole trip?

Always use booster seats in conjunction
with your vehicle lap and shoulder belt.

E70710

•

F150 (TF6) , enUSA

High back booster seats

Child Safety
If, with a backless booster seat, you cannot
find a seating position that adequately
supports your child's head, a high back
booster seat would be a better choice.

shoulder. The following drawings compare
the ideal fit (center) to a shoulder belt
uncomfortably close to the neck and a
shoulder belt that could slip off the
shoulder. The drawings also show how the
lap belt should be low and snug across the
child's hips.

Children and booster seats vary in size and
shape. Choose a booster that keeps the
lap belt low and snug across the hips,
never up across the stomach, and lets you
adjust the shoulder belt to cross the chest
and rest snugly near the center of the

E142596

E142597

If the booster seat slides on the vehicle
seat upon which it is being used, placing a
rubberized mesh sold as shelf or carpet
liner under the booster seat may improve
this condition. Do not introduce any item
thicker than this under the booster seat.
Check with the booster seat
manufacturer's instructions.

CHILD SEAT POSITIONING
WARNINGS
Airbags can kill or injure a child in a
child seat. Never place a rear-facing
child seat in front of an active airbag.
If you must use a forward-facing child seat
in the front seat, move the vehicle seat
upon which the child seat is installed all

F150 (TF6) , enUSA

Child Safety
WARNINGS
the way back. When possible, all children
age 12 and under should be properly
restrained in a rear seating position. If all
children cannot be seated and restrained
properly in a rear seating position, properly
restrain the largest child in the front seat.

WARNINGS
Never let a passenger hold a child on
his or her lap while your vehicle is
moving. The passenger cannot
protect the child from injury in a crash,
which may result in serious injury or death.
Never use pillows, books, or towels
to boost a child. They can slide
around and increase the likelihood
of injury or death in a crash.

Always carefully follow the
instructions and warnings provided
by the manufacturer of any child
restraint to determine if the restraint device
is appropriate for your child's size, height,
weight, or age. Follow the child restraint
manufacturer's instructions and warnings
provided for installation and use in
conjunction with the instructions and
warnings provided by your vehicle
manufacturer. A safety seat that is
improperly installed or utilized, is
inappropriate for your child's height, age,
or weight or does not properly fit the child
may increase the risk of serious injury or
death.

Always restrain an unoccupied child
seat or booster seat. These objects
may become projectiles in a crash or
sudden stop, which may increase the risk
of serious injury.
Never place, or allow a child to place,
the shoulder belt under a child's arm
or behind the back because it
reduces the protection for the upper part
of the body and may increase the risk of
injury or death in a crash.
To avoid risk of injury, do not leave
children or pets unattended in your
vehicle.

F150 (TF6) , enUSA

Child Safety

Recommendations for attaching child safety restraints for children
Restraint
Type

Combined
weight of
child and
child seat

Use any attachment method as indicated below by X
LATCH
(lower
anchors
and top
tether
anchor)

LATCH
(lower
anchors
only)

Rear facing Up to 65 lb
child seat
(29 kg)

Safety belt Safety belt Safety belt
and LATCH
only
and top
(lower
tether
anchors
anchor
and top
tether
anchor)

Rear facing Over 65 lb
child seat
(29 kg)
Forward
facing
child seat

Up to 65 lb
(29 kg)

Forward
facing
child seat

Over 65 lb
(29 kg)

X
X

Note: The child seat must rest tightly
against the vehicle seat upon which it is
installed. It may be necessary to lift or
remove the head restraint. See Seats (page
114).

CHILD SAFETY LOCKS
When these locks are set, the rear doors
cannot be opened from the inside.

E112197

The childproof locks are located on the
rear edge of each rear door and must be
set separately for each door.

F150 (TF6) , enUSA

Child Safety
Left-Hand Side
Turn counterclockwise to lock and
clockwise to unlock.

Right-Hand Side
Turn clockwise to lock and
counterclockwise to unlock.

F150 (TF6) , enUSA

Safety Belts
PRINCIPLE OF OPERATION

WARNINGS
When possible, all children 12 years
old and under should be properly
restrained in a rear seating position.
Failure to follow this could seriously
increase the risk of injury or death.

WARNINGS
Always drive and ride with your seat
back upright and the lap belt snug
and low across the hips.

Safety belts and seats can become
hot in a vehicle that has been closed
up in sunny weather; they could burn
a small child. Check seat covers and
buckles before you place a child anywhere
near them.

To reduce the risk of injury, make
sure children sit where they can be
properly restrained.
Never let a passenger hold a child on
his or her lap while the vehicle is
moving. The passenger cannot
protect the child from injury in a crash,
which may result in serious injury or death.

Front and rear seat occupants,
including pregnant women, should
wear safety belts for optimum
protection in an accident.

All occupants of the vehicle,
including the driver, should always
properly wear their safety belts, even
when an airbag supplemental restraint
system is provided. Failure to properly wear
your safety belt could seriously increase
the risk of injury or death.

All seating positions in this vehicle have
lap and shoulder safety belts. All
occupants of the vehicle should always
properly wear their safety belts, even when
an airbag supplemental restraint system
is provided.

It is extremely dangerous to ride in a
cargo area, inside or outside of a
vehicle. In a crash, people riding in
these areas are more likely to be seriously
injured or killed. Do not allow people to ride
in any area of your vehicle that is not
equipped with seats and safety belts. Be
sure everyone in your vehicle is in a seat
and using a safety belt properly.

The safety belt system consists of:
• lap and shoulder safety belts.
• shoulder safety belt with automatic
locking mode, (except driver safety
belt).
• height adjuster at the front outboard
seating positions.
• safety belt pretensioner at the front
outboard seating positions.
• belt tension sensor at the front
outboard passenger seating position.

In a rollover crash, an unbelted
person is significantly more likely to
die than a person wearing a safety
belt.
Each seating position in your vehicle
has a specific safety belt assembly
which is made up of one buckle and
one tongue that are designed to be used
as a pair. 1) Use the shoulder belt on the
outside shoulder only. Never wear the
shoulder belt under the arm. 2) Never
swing the safety belt around your neck over
the inside shoulder. 3) Never use a single
belt for more than one person.

•

F150 (TF6) , enUSA

safety belt warning light and chime.

Safety Belts
•

crash sensors and monitoring system
with readiness indicator.

The safety belt pretensioners at the front
seating positions are designed to tighten
the safety belts when activated. In frontal
and near-frontal crashes, side crashes and
rollovers, the safety belt pretensioners may
be activated alone or, if the crash is of
sufficient severity, together with the front
airbags.
E142588

FASTENING THE SAFETY
BELTS

2. To unfasten, press the release button
and remove the tongue from the
buckle.

The front outboard and rear safety
restraints in the vehicle are combination
lap and shoulder belts.

Using the Safety Belt with Cinch
Tongue (Front Center Seat)
The cinch tongue will slide up and down
the belt webbing when the belt is stowed
or while putting safety belts on. When you
buckle the lap and shoulder safety belt,
the cinch tongue will allow you to shorten
the lap portion, but pinches the webbing
to keep the lap portion from getting longer.
The cinch tongue is designed to slip during
a crash, so always wear the shoulder belt
properly and do not allow any slack in
either the lap or shoulder portions.

E142587

Before you can reach and latch a lap and
shoulder belt having a cinch tongue into
the buckle, you may have to lengthen the
lap belt portion of it.

Insert the belt tongue into the proper
buckle (the buckle closest to the
direction the tongue is coming from)
until you hear a snap and feel it latch.
Make sure you securely fasten the
tongue in the buckle.

E162708

F150 (TF6) , enUSA

Safety Belts
Using Safety Belts During
Pregnancy

To lengthen the lap belt, pull some
webbing out of the shoulder belt
retractor.
2. While holding the webbing below the
tongue, grasp the tip (metal portion)
of the tongue so that it is parallel to the
webbing and slide the tongue upward.
3. Provide enough lap belt length so that
the tongue can reach the buckle.

WARNING
Always ride and drive with your
seatback upright and the safety belt
properly fastened. The lap portion of
the safety belt should fit snug and be
positioned low across the hips. The
shoulder portion of the safety belt should
be positioned across the chest. Pregnant
women should also follow this practice.

Fastening the Cinch Tongue
WARNING
The lap belt should fit snugly and as
low as possible around the hips, not
across the waist.
1.

Pull the lap and shoulder belt from the
retractor so that the shoulder belt
portion of the safety belt crosses your
shoulder and chest.
2. Be sure the belt is not twisted. If the
belt is twisted, remove the twist.
3. Insert the belt tongue into the proper
buckle for your seating position until
you hear a snap and feel it latch.
4. Make sure you securely fasten the
tongue to the buckle by pulling on the
tongue.

E142590

Pregnant women should always wear their
safety belt. Position the lap belt portion of
a combination lap and shoulder belt low
across the hips below the belly and worn
as tight as comfort will allow. Position the
shoulder belt to cross the middle of the
shoulder and the center of the chest.

While you are fastened in the safety belt,
the lap and shoulder belt with a cinch
tongue adjusts to your movement.
However, if you brake hard, turn hard, or if
your vehicle receives an impact of 5 mph
(8 km/h) or more, the safety belt will
become locked and help reduce your
forward movement.

Safety Belt Locking Modes
WARNINGS
After any vehicle crash, the safety
belt system at all passenger seating
positions must be checked by an
authorized dealer to verify that the
automatic locking retractor feature for
child seats is still functioning properly. In
addition, all safety belts should be checked
for proper function.

F150 (TF6) , enUSA

Safety Belts
When to Use the Automatic Locking
Mode

WARNINGS
The belt and retractor must be
replaced if the safety belt assembly
automatic locking retractor feature
or any other safety belt function is not
operating properly when checked by an
authorized dealer. Failure to replace the
belt and retractor assembly could increase
the risk of injury in crashes.

Use this mode any time you install a child
safety seat in a front outboard passenger
seating position in a Regular Cab,
SuperCab, SuperCrew or any rear seating
position of a SuperCab or SuperCrew. The
optional front seat's center safety belt has
a cinch mechanism. Children 12 years old
and under should be properly restrained in
a rear seat whenever possible. See Child
Safety (page 14).

All safety restraints in the vehicle are
combination lap and shoulder belts. The
driver safety belt has the first type of
locking mode, and the front outboard
passenger and rear seat safety belts have
both types of locking modes described as
follows:

How to Use the Automatic Locking
Mode

Vehicle Sensitive Mode
This is the normal retractor mode, which
allows free shoulder belt length
adjustment to your movements and
locking in response to vehicle movement.
For example, if the driver brakes suddenly,
turns a corner sharply, or the vehicle
receives an impact of about 5 mph (8
km/h) or more, the combination safety
belts will lock to help reduce forward
movement of the driver and passengers.

E142591

Buckle the combination lap and
shoulder belt.
2. Grasp the shoulder portion and pull
downward until you pull the entire belt
out.

In addition, the retractor is designed to lock
if the webbing is pulled out too quickly. If
this occurs, let the belt retract slightly and
pull webbing out again in a slow and
controlled manner.

Allow the belt to retract. As the belt
retracts, you will hear a clicking sound. This
indicates the safety belt is now in the
automatic locking mode.

Automatic Locking Mode
In this mode, the shoulder belt is
automatically pre-locked. The belt will still
retract to remove any slack in the shoulder
belt. The automatic locking mode is not
available on the driver safety belt.

How to Disengage the Automatic
Locking Mode
Unbuckle the combination lap and
shoulder belt and allow it to retract
completely to disengage the automatic
locking mode and activate the vehicle
sensitive (emergency) locking mode.

F150 (TF6) , enUSA

Safety Belts
Safety Belt Extension Assembly
WARNING
Do not use extensions to change the
fit of the shoulder belt across the
torso.
If the safety belt is too short when fully
extended, you can obtain a safety belt
extension assembly from an authorized
dealer.

E145664

Use only extensions manufactured by the
same supplier as the safety belt.
Manufacturer identification is located at
the end of the webbing on the label. Also,
use the safety belt extension only if the
safety belt is too short for you when fully
extended.

Adjust the height of the shoulder belt so
the belt rests across the middle of your
shoulder.
To adjust the shoulder belt height:
1.

Pull the button and slide the height
adjuster up or down.
2. Release the button and pull down on
the height adjuster to make sure it is
locked in place.

SAFETY BELT HEIGHT
ADJUSTMENT

SAFETY BELT WARNING LAMP
AND INDICATOR CHIME

WARNING
Position the safety belt height
adjuster so that the belt rests across
the middle of your shoulder. Failure
to adjust the safety belt properly could
reduce the effectiveness of the safety belt
and increase the risk of injury in a crash.

This lamp illuminates and an
audible warning will sound if the
driver's safety belt has not been
fastened when the vehicle's ignition is
turned on.

F150 (TF6) , enUSA

Safety Belts
Conditions of operation
If...

Then...

The driver's safety belt is not buckled
before the ignition switch is turned to the
on position...

The safety belt warning light illuminates 12 minutes and the warning chime sounds
4-8 seconds.

The driver's safety belt is buckled while the
indicator light is illuminated and the
warning chime is sounding...

The safety belt warning light and warning
chime turn off.

The driver's safety belt is buckled before The safety belt warning light and indicator
the ignition switch is turned to the on posichime remain off.
tion...
The system uses information from the
front passenger sensing system to
determine if a front seat passenger is
present and therefore potentially in need
of a warning. To avoid activating the
Belt-Minder feature for objects placed in
the front passenger seat, warnings will only
be given to front seat occupants as
determined by the front passenger sensing
system.

SAFETY BELT MINDER
Belt-Minder™
This feature supplements the safety belt
warning function. It provides additional
reminders by intermittently sounding a
chime and illuminating the safety belt
warning light when the driver or front
passenger seat is occupied and the safety
belt is unbuckled.

If the Belt-Minder warnings have expired
(warnings for about five minutes) for one
occupant (driver or front passenger), the
other occupant can still activate the
Belt-Minder feature.

F150 (TF6) , enUSA

Safety Belts

If...

Then...

The driver and front passenger safety belt
is buckled before the ignition switch is
turned to the on position or less than 1-2
minutes have elapsed since the ignition
switch has been turned to on...

The Belt-Minder feature will not activate.

The driver or front passenger safety belt is The Belt-Minder feature is activated - the
not buckled when the vehicle has reached safety belt warning light illuminates and
at least 6 mph (9.7 km/h) and 1-2 minutes the warning chime sounds for six seconds
have elapsed since the ignition switch has every 25 seconds, repeating for about five
minutes or until the safety belts are
been turned to on...
buckled.
The Belt-Minder feature is activated - the
The driver or front passenger safety belt
becomes unbuckled for about one minute safety belt warning light illuminates and
while the vehicle is traveling at least 6 mph the warning chime sounds for six seconds
(9.7 km/h) and more than 1-2 minutes have every 25 seconds, repeating for about five
minutes or until the safety belts are
elapsed since the ignition switch has been
buckled.
turned to on...
Note: If you are using MyKey, you cannot
disable the Belt-Minder. Also, if the
Belt-Minder has been previously disabled,
it will be re-enabled during the use of
MyKey. See MyKey™ (page 53).

Deactivating and Activating the
Belt-Minder Feature
WARNING
While the system allows you to
deactivate it, this system is designed
to improve your chances of being
safely belted and surviving an accident.
We recommend you leave the system
activated for yourself and others who may
use the vehicle. To reduce the risk of injury,
do not deactivate or activate the system
while driving the vehicle.

Read Steps 1 - 4 thoroughly before
proceeding with the programming
procedure.
Before following the procedure, make sure
that:
• The parking brake is set.
• The transmission is in park (P).
• The ignition is off.
• The driver and front passenger safety
belt is unbuckled.

Note: The driver and front passenger
Belt-Minder are deactivated and activated
independently. When deactivating or
activating one seating position, do not
buckle the other position, as this will
terminate the process.

Turn the ignition on. Do not start the
engine.
2. Wait until the safety belt warning light
turns off (about one minute). Step 3
must be completed within 30 seconds
after the safety belt warning light turns
off.

F150 (TF6) , enUSA

Safety Belts
3. Buckle, then unbuckle the safety belt
three times at a moderate speed,
ending with the safety belt in the
unbuckled state. After Step 3, the
safety belt warning light will turn on.
4. While the safety belt warning light is
on, buckle then unbuckle the safety
belt. After Step 4, the safety belt
warning light will flash for confirmation.
• This will disable the feature if it is
currently enabled.
• This will enable the feature if it is
currently disabled.

Ford Motor Company recommends that
all safety belt assemblies in use in vehicles
involved in a crash be replaced. However,
if the crash was minor and an authorized
dealer finds that the belts do not show
damage and continue to operate properly,
they do not need to be replaced. Safety
belt assemblies not in use during a crash
should also be inspected and replaced if
either damage or improper operation is
noted.
Properly care for safety belts. See Vehicle
Care (page 259).

CHILD RESTRAINT AND
SAFETY BELT MAINTENANCE
Inspect the vehicle safety belts and child
safety seat systems periodically to make
sure they work properly and are not
damaged. Inspect the vehicle and child
seat safety belts to make sure there are no
nicks, tears or cuts. Replace if necessary.
All vehicle safety belt assemblies, including
retractors, buckles, front safety belt buckle
assemblies, buckle support assemblies
(slide bar-if equipped), shoulder belt
height adjusters (if equipped), shoulder
belt guide on seat back (if equipped), child
safety seat LATCH and tether anchors, and
attaching hardware, should be inspected
after a crash. Read the child restraint
manufacturer's instructions for additional
inspection and maintenance information
specific to the child restraint.

F150 (TF6) , enUSA

Personal Safety System™
The Personal Safety System provides an
improved overall level of frontal crash
protection to front seat occupants and is
designed to help further reduce the risk of
airbag-related injuries. The system is able
to analyze different occupant conditions
and crash severity before activating the
appropriate safety devices to help better
protect a range of occupants in a variety
of frontal crash situations.

module. During a crash, the restraints
control module may activate the safety
belt pretensioners and may activate either
one or both stages of the dual-stage airbag
supplemental restraints based on crash
severity and occupant conditions.

Your vehicle's Personal Safety System
consists of:
• Driver and passenger dual-stage airbag
supplemental restraints.
• Front outboard safety belts with
pretensioners, energy management
retractors (first row only), and safety
belt usage sensors.
• Driver’s seat position sensor.
• Front passenger sensing system.
• Passenger airbag off and on indicator
lamp.
• Front crash severity sensors.
• Restraints control module with impact
and safing sensors.
• Restraint system warning light and
backup tone.
• The electrical wiring for the airbags,
crash sensor(s), safety belt
pretensioners, front safety belt usage
sensors, driver seat position sensor,
front passenger sensing system, and
indicator lights.

How Does the Personal Safety
System Work?
The Personal Safety System can adapt the
deployment strategy of your vehicle’s
safety devices according to crash severity
and occupant conditions. A collection of
crash and occupant sensors provides
information to the restraints control

F150 (TF6) , enUSA

Supplementary Restraints System
The airbags are a supplemental restraint
system and are designed to work with the
safety belts to help protect the driver and
right front passenger from certain upper
body injuries. Airbags do not inflate slowly;
there is a risk of injury from a deploying
airbag.

PRINCIPLE OF OPERATION
WARNINGS
Airbags do not inflate slowly or
gently, and the risk of injury from a
deploying airbag is the greatest close
to the trim covering the airbag module.

Note: You will hear a loud bang and see a
cloud of harmless powdery residue if an
airbag deploys. This is normal.

All occupants of your vehicle,
including the driver, should always
properly wear their safety belts, even
when an airbag supplemental restraint
system is provided. Failure to properly wear
your safety belt could seriously increase
the risk of injury or death.

The airbags inflate and deflate rapidly
upon activation. After airbag deployment,
it is normal to notice a smoke-like, powdery
residue or smell the burnt propellant. This
may consist of cornstarch, talcum powder
(to lubricate the bag) or sodium
compounds (for example, baking soda)
that result from the combustion process
that inflates the airbag. Small amounts of
sodium hydroxide may be present which
may irritate the skin and eyes, but none of
the residue is toxic.

Always transport children 12 years
old and under in the back seat and
always properly use appropriate
child restraints. Failure to follow this could
seriously increase the risk of injury or death.
Never place your arm over the airbag
module as a deploying airbag can
result in serious arm fractures or
other injuries.

While the system is designed to help
reduce serious injuries, contact with a
deploying airbag may also cause abrasions
or swelling. Temporary hearing loss is also
a possibility as a result of the noise
associated with a deploying airbag.
Because airbags must inflate rapidly and
with considerable force, there is the risk of
death or serious injuries such as fractures,
facial and eye injuries or internal injuries,
particularly to occupants who are not
properly restrained or are otherwise out of
position at the time of airbag deployment.
Thus, it is extremely important that
occupants be properly restrained as far
away from the airbag module as possible
while maintaining vehicle control.

Airbags can kill or injure a child in a
child seat. Never place a rear-facing
child seat in front of an active airbag.
If you must use a forward-facing child seat
in the front seat, move the seat upon which
the child seat is installed all the way back.
Do not attempt to service, repair, or
modify the airbag supplemental
restraint systems or its fuses as you
could be seriously injured or killed. Contact
your authorized dealer as soon as possible.
Several airbag system components
get hot after inflation. To avoid risk
of injury, do not touch them after
inflation.

Routine maintenance of the airbags is not
required.

If the airbag has deployed, the airbag
will not function again and must be
replaced immediately. If the airbag
is not replaced, the unrepaired area will
increase the risk of injury in a crash.

F150 (TF6) , enUSA

Supplementary Restraints System
Proper Driver and Front Passenger
Seating Adjustment

DRIVER AND PASSENGER
AIRBAGS

WARNING

WARNINGS
Never place your arm or any objects
over an airbag module. Placing your
arm over a deploying airbag can
result in serious arm fractures or other
injuries. Objects placed on or over the
airbag inflation area may cause those
objects to be propelled by the airbag into
your face and torso causing serious injury.

The National Highway Traffic Safety
Administration recommends a
minimum distance of at least 10
inches (25 centimeters) between an
occupant’s chest and the driver airbag
module.
To properly position yourself away from
the airbag:
• Move your seat to the rear as far as you
can while still reaching the pedals
comfortably.
• Recline the seat slightly (one or two
degrees) from the upright position.

After all occupants have adjusted their
seats and put on safety belts, it is very
important that they continue to sit
properly. Properly seated occupants sit
upright, lean against the seat back, and
center themselves on the seat cushion,
with their feet comfortably extended on
the floor. Sitting improperly can increase
the chance of injury in a crash event. For
example, if an occupant slouches, lies
down, turns sideways, sits forward, leans
forward or sideways, or puts one or both
feet up, the chance of injury during a crash
is greatly increased.

E151127

The driver and front passenger airbags will
deploy during significant frontal and near
frontal crashes.

Children and Airbags

The driver and passenger front airbag
system consists of:
• driver and passenger airbag modules.
• front passenger sensing system.

WARNING

· crash sensors and monitoring
system with readiness indicator.
See Crash Sensors and Airbag
Indicator (page 48).

F150 (TF6) , enUSA

Supplementary Restraints System
WARNINGS
Sitting improperly out of position or
with the seatback reclined too far
can take off weight from the seat
cushion and affect the decision of the front
passenger sensing system, resulting in
serious injury or death in a crash. Always
sit upright against your seatback, with your
feet on the floor.
To reduce the risk of possible serious
injury: Do not stow objects in the
seatback map pocket or hang
objects off the seatback if a child is in the
front passenger seat. Do not place objects
underneath the front passenger seat or
between the seat and the center console.
Check the passenger airbag status
indicator lamp for proper airbag status.
Failure to follow these instructions may
interfere with the front passenger seat
sensing system.

E142846

Children must always be properly
restrained. Accident statistics suggest that
children are safer when properly restrained
in the rear seating positions than in the
front seating position. Failure to follow
these instructions may increase the risk of
injury in a crash.
If two adults and a child occupy a Regular
Cab, properly restrain the child in the
center front unless doing so would interfere
with driving your vehicle. This provides lap
and shoulder belt protection for all
occupants, and airbag protection for the
adults. A child or infant properly restrained
in the center front seat should not incur
risk of serious injury from the airbags.

Any alteration or modification to the
front passenger seat may affect the
performance of the front passenger
sensing system.
The front passenger airbag is not
designed to offer protection to an
occupant in the center seating
position.

FRONT PASSENGER SENSING
SYSTEM

An out of position front center
occupant could affect the decision
of the front passenger sensing
system.

WARNINGS
Even with Advanced Restraints
Systems, children 12 and under
should be properly restrained in a
rear seating position. Failure to follow this
could seriously increase the risk of injury or
death.

The system works with sensors that are
part of the passenger seat and safety belt
to detect the presence of a properly seated
occupant and determine if the front
passenger's frontal airbag should be
enabled or not.

F150 (TF6) , enUSA

Supplementary Restraints System
High-series vehicles (if equipped)

The front passenger sensing system is
designed to enable (may inflate) the front
passenger's frontal airbag anytime the
system senses that a person of adult size
is sitting properly in the front passenger
seat.
•

E162720

The front passenger sensing system uses
a passenger airbag status indicator which
will illuminate indicating that the front
passenger frontal airbag is either ON
(enabled) or OFF (disabled). The indicator
lamp is located by the radio.

If a person of adult size is sitting in the front
passenger seat, but the passenger airbag
status indicator OFF lamp is lit, it is
possible that the person is not sitting
properly in the seat. If this happens:
• Turn your vehicle off and ask the
person to place the seatback in the full
upright position.
• Have the person sit upright in the seat,
centered on the seat cushion, with the
person's legs comfortably extended.
• Restart your vehicle and have the
person remain in this position for about
two minutes. This will allow the system
to detect that person and enable the
passenger's frontal airbag.
• If the passenger airbag status indicator
OFF lamp remains lit even after this,
you should advise the person to ride in
the rear seat.

The front passenger sensing system is
designed to disable (will not inflate) the
front passenger frontal airbag when the
front passenger seat is unoccupied, or a
rear facing infant seat, a forward-facing
child restraint, or a booster seat is
detected. Even with this technology,
parents are strongly encouraged to
always properly restrain children in the rear
seat. The sensor also turns off the
passenger front airbag and seat-mounted
side airbag when the passenger seat is
empty.
•

•

When the front passenger sensing
system disables (will not inflate) the
front passenger frontal airbag, the
passenger airbag status indicator will
illuminate the OFF lamp and stay lit to
remind you that the front passenger
frontal airbag is disabled.
If the child restraint has been installed
and the passenger airbag status
indicator illuminates the ON lamp, then
turn your vehicle off, remove the child
restraint from your vehicle and reinstall
the restraint following the child
restraint manufacturer's instructions.

F150 (TF6) , enUSA

When the front passenger sensing
system enables the front passenger
frontal airbag (may inflate), the
passenger airbag status indicator will
illuminate the ON lamp and remain
illuminated.

Supplementary Restraints System

Occupant

Passenger airbag status
indicator

Passenger airbag

Empty

OFF: Lit

Disabled

ON: Unlit
Child

OFF: Lit

Adult

OFF: Unlit

Disabled

ON: Unlit
Enabled

ON: Lit
Note: When the passenger airbag status
indicator OFF lamp is illuminated, the
passenger side airbag (seat mounted) may
be disabled to avoid the risk of airbag
deployment issues.

•

After all occupants have adjusted their
seats and put on safety belts, it is very
important that they continue to sit
properly. A properly seated occupant sits
upright, leaning against the seatback, and
centered on the seat cushion, with their
feet comfortably extended on the floor.
Sitting improperly can increase the chance
of injury in a crash event. For example, if
an occupant slouches, lies down, turns
sideways, sits forward, leans forward or
sideways, or puts one or both feet up, the
chance of injury during a crash is greatly
increased.

The conditions listed above may cause the
weight of a properly seated occupant to
be incorrectly interpreted by the front
passenger sensing system. The person in
the front passenger seat may appear
heavier or lighter due to the conditions
described in the previous list.

If you think that the state of the passenger
airbag status indicator lamp is incorrect,
check for the following:
• Objects lodged underneath the seat
• Objects between the seat cushion and
the center console
• Objects hanging off the seatback
• Objects stowed in the seatback map
pocket
• Objects placed on the occupant's lap
• Cargo interference with the seat

The driver and adult passengers should
check for any objects that may be lodged
underneath the front passenger seat or
cargo interfering with the seat.

•

Make sure the front passenger
sensing system is operating
properly. See Crash Sensors
and Airbag Indicator (page 48).
If the airbag readiness light is lit, do the
following:

If objects are lodged or cargo is interfering
with the seat; please take the following
steps to remove the obstruction:
• Pull your vehicle over.
• Turn your vehicle off.

F150 (TF6) , enUSA

Other passengers pushing or pulling on
the seat
Rear passenger feet and knees resting
or pushing on the seat

Supplementary Restraints System
•

•
•
•

•

The front passenger sensing system is
designed to disable (will not inflate) the
front passenger's frontal airbag when the
front passenger seat is unoccupied, or a
rear facing infant seat, a forward-facing
child restraint, or a booster seat is
detected. Even with this technology,
parents are strongly encouraged to
always properly restrain children in the rear
seat. The sensor also turns off the
passenger front airbag and seat-mounted
side airbag when the passenger seat is
empty.

Driver or adult passengers should
check for any objects lodged
underneath the front passenger seat
or cargo interfering with the seat.
Remove the obstruction(s) (if found).
Restart your vehicle.
Wait at least two minutes and verify
that the airbag readiness light in the
instrument cluster is no longer
illuminated.
If the airbag readiness light in the
instrument cluster remains illuminated,
this may or may not be a problem due
to the front passenger sensing system.

•

Do not attempt to repair or service the
system. Take your vehicle immediately to
an authorized dealer.
If it is necessary to modify an advanced
front airbag system to accommodate a
person with disabilities, contact the Ford
Customer Relationship Center.

•

Low-series vehicles (if equipped)

When the front passenger sensing
system disables (will not inflate) the
front passenger frontal airbag, the
indicator lamp will illuminate and stay
lit to remind you that the front
passenger frontal airbag is disabled.
If the child restraint has been installed
and the indicator lamp is not lit, turn
your vehicle off, remove the child
restraint from your vehicle and reinstall
the restraint following the child
restraint manufacturer's instructions.

E162721

The front passenger sensing system uses
a pass airbag off indicator which will
illuminate and stay lit to remind you that
the front passenger frontal airbag is
disabled. The indicator lamp is located by
the radio.
Note: The indicator lamp will illuminate for
a short period of time when the ignition is
first turned on to confirm it is functional.

F150 (TF6) , enUSA

When the front passenger sensing
system enables the front passenger
frontal airbag (may inflate), the
indicator will be unlit and stay unlit.

Supplementary Restraints System
If a person of adult size is sitting in the front
passenger seat, but the pass airbag off
indicator lamp is lit, it is possible that the
person is not sitting properly in the seat. If
this happens:
• Turn your vehicle off and ask the
person to place the seatback in the full
upright position.
• Have the person sit upright in the seat,
centered on the seat cushion, with the
person's legs comfortably extended.

•

Occupant

Passenger airbag off indicator lamp

Passenger airbag

Empty

Unlit

Disabled

Child

Lit

Disabled

Adult

Unlit

Enabled

If it is necessary to modify an advanced
front airbag system to accommodate a
person with disabilities, contact the Ford
Customer Relationship Center. See
Getting the Services You Need (page
219).

Note: When the passenger airbag off lamp
is illuminated, the passenger side airbag
(seat mounted) may be disabled to avoid
the risk of airbag deployment injuries.
After all occupants have adjusted their
seats and put on safety belts, it is very
important that they continue to sit
properly. A properly seated occupant sits
upright, leaning against the seat back, and
centered on the seat cushion, with their
feet comfortably extended on the floor.
Sitting improperly can increase the chance
of injury in a crash event. For example, if
an occupant slouches, lies down, turns
sideways, sits forward, leans forward or
sideways, or puts one or both feet up, the
chance of injury during a crash is greatly
increased.

SIDE AIRBAGS
WARNINGS
Do not place objects or mount
equipment on or near the airbag
cover, on the side of the seatbacks
(of the front seats), or in front seat areas
that may come into contact with a
deploying airbag. Failure to follow these
instructions may increase the risk of
personal injury in the event of a crash.

Make sure the front passenger
sensing system is operating
properly. See Crash Sensors
and Airbag Indicator (page 48).

Do not use accessory seat covers.
The use of accessory seat covers
may prevent the deployment of the
side airbags and increase the risk of injury
in an accident.

Do not attempt to repair or service the
system. Take your vehicle immediately to
an authorized dealer.
45

F150 (TF6) , enUSA

Restart your vehicle and have the
person remain in this position for about
two minutes. This will allow the system
to detect that person and enable the
passenger's frontal airbag.
If the indicator lamp remains lit even
after this, you should advise the person
to ride in the rear seat.

Supplementary Restraints System
The system consists of the following:
• A label or embossed side panel
indicating that side airbags are fitted
to your vehicle.
• Side airbags located inside the driver
and front passenger seatbacks.
• Front passenger sensing system.

WARNINGS
Do not lean your head on the door.
The side airbag could injure you as it
deploys from the side of the
seatback.
Do not attempt to service, repair, or
modify the airbag, its fuses or the
seat cover on a seat containing an
airbag as you could be seriously injured or
killed. Contact your authorized dealer as
soon as possible.

·Crash sensors and monitoring
system with readiness indicator.
See Crash Sensors and Airbag
Indicator (page 48).

If the side airbag has deployed, the
airbag will not function again. The
side airbag system (including the
seat) must be inspected and serviced by
an authorized dealer. If the airbag is not
replaced, the unrepaired area will increase
the risk of injury in a crash.

Note: The passenger sensing system will
deactivate the passenger seat-mounted
side airbag if it detects an empty passenger
seat.
The design and development of the side
airbag system included recommended
testing procedures that were developed
by a group of automotive safety experts
known as the Side Airbag Technical
Working Group. These recommended
testing procedures help reduce the risk of
injuries related to the deployment of side
airbags.

The side airbags are located on the
outboard side of the seatbacks of the front
seats. In certain sideways crashes, the
airbag on the side affected by the crash
will be inflated. The airbag was designed
to inflate between the door panel and
occupant to further enhance the protection
provided occupants in side impact crashes.

SAFETY CANOPY™
WARNINGS
Do not place objects or mount
equipment on or near the headliner
at the siderail that may come into
contact with a deploying curtain airbag.
Failure to follow these instructions may
increase the risk of personal injury in the
event of a crash.
Do not lean your head on the door.
The curtain airbag could injure you
as it deploys from the headliner.

E152533

F150 (TF6) , enUSA

Supplementary Restraints System
WARNINGS
Do not attempt to service, repair, or
modify the curtain airbags, its fuses,
the A, B, or C pillar trim, or the
headliner on a vehicle containing curtain
airbags as you could be seriously injured
or killed. Contact your authorized dealer
as soon as possible.
All occupants of your vehicle
including the driver should always
wear their safety belts even when an
airbag supplemental restraint system and
curtain airbag is provided. Failure to
properly wear your safety belt could
seriously increase the risk of injury or death.

E75004

The system consists of the following:
• Safety canopy curtain airbags located
above the trim panels over the front
and rear side windows identified by a
label or wording on the headliner or
roof-pillar trim.
• A flexible headliner which opens above
the side doors to allow air curtain
deployment

To reduce risk of injury, do not
obstruct or place objects in the
deployment path of the curtain
airbag.
If the curtain airbags have deployed,
the curtain airbags will not function
again. The curtain airbags (including
the A, B and C pillar trim and headliner)
must be inspected and serviced by an
authorized dealer. If the curtain airbag is
not replaced, the unrepaired area will
increase the risk of injury in a crash.

•

The Safety Canopy will deploy during
significant side crashes or when a certain
likelihood of a rollover event is detected
by the rollover sensor. The Safety Canopy
is mounted to the roof side-rail sheet
metal, behind the headliner, above each
row of seats. In certain sideways crashes
or rollover events, the Safety Canopy will
be activated, regardless of which seats are
occupied. The Safety Canopy is designed
to inflate between the side window area
and occupants to further enhance
protection provided in side impact crashes
and rollover events.

Children 12 years old and under should
always be properly restrained in the rear
seats. The Safety Canopy will not interfere
with children restrained using a properly
installed child or booster seat because it
is designed to inflate downward from the
headliner above the doors along the side
window opening.
The design and development of the Safety
Canopy included recommended testing
procedures that were developed by a
group of automotive safety experts known
as the Side Airbag Technical Working
Group. These recommended testing
procedures help reduce the risk of injuries
related to the deployment of side airbags
(including the Safety Canopy).

F150 (TF6) , enUSA

The crash sensors and monitoring
system have a readiness indicator. See
Crash Sensors and Airbag Indicator
(page 48).

Supplementary Restraints System
If any of these things happen, even
intermittently, have the supplemental
restraint system serviced at an authorized
dealer immediately. Unless serviced, the
system may not function properly in the
event of a crash.

CRASH SENSORS AND
AIRBAG INDICATOR
WARNING
Modifying or adding equipment to
the front end of the vehicle (including
frame, bumper, front end body
structure and tow hooks) may affect the
performance of the airbag system,
increasing the risk of injury. Do not modify
the front end of the vehicle.

The fact that the safety belt pretensioners
or front airbags did not activate for both
front seat occupants in a crash does not
mean that something is wrong with the
system. Rather, it means the restraints
control module determined the accident
conditions (crash severity, belt usage)
were not appropriate to activate these
safety devices.
• The design of the front airbags is to
activate only in frontal and near-frontal
crashes (not rollovers, side impacts or
rear impacts) unless the crash causes
sufficient frontal deceleration.
• The design of the safety belt
pretensioners is to activate in frontal,
near-frontal and side crashes, and in
rollovers.
• The design of the side airbags is to
inflate in certain side impact crashes.
Side airbags may activate in other
types of crashes if the vehicle
experiences sufficient sideways motion
or deformation.
• The design of the Safety Canopy is to
inflate in certain side impact crashes
or rollover events. The Safety Canopy
may activate in other types of crashes
if the vehicle experiences sufficient
sideways motion or deformation, or a
certain likelihood of rollover.

Your vehicle has a collection of crash and
occupant sensors which provide
information to the restraints control
module which deploys (activates) the
front safety belt pretensioners, driver
airbag, passenger airbag, seat mounted
side airbags, and the Safety Canopy®.
Based on the type of crash (frontal impact,
side impact or rollover), the restraints
control module will deploy the appropriate
safety devices.
The restraints control module also
monitors the readiness of the above safety
devices plus the crash and occupant
sensors. The readiness of the safety
system is indicated by a warning indicator
light in the instrument cluster or by a
backup tone if the warning light is not
working. See Instrument Cluster (page
81). Routine maintenance of the airbag is
not required.
A difficulty with the system is indicated by
one or more of the following:
The readiness light will not
illuminate immediately after the
ignition is turned on.
•
•

AIRBAG DISPOSAL

The readiness light will either flash or
stay lit.
A series of five beeps will be heard. The
tone pattern will repeat periodically
until the problem, the light or both are
repaired.

Contact your authorized dealer as soon as
possible. Airbags must be disposed of by
qualified personnel.

F150 (TF6) , enUSA

Keys and Remote Controls
GENERAL INFORMATION ON
RADIO FREQUENCIES

REMOTE CONTROL

This device complies with Part 15 of the
FCC Rules and with Industry Canada
license-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) This device
must accept any interference received,
including interference that may cause
undesired operation.

(If Equipped)

Integrated Keyhead Transmitters

Note: Changes or modifications not
expressively approved by the party
responsible for compliance could void the
user's authority to operate the equipment.
The term IC before the radio certification
number only signifies that Industry Canada
technical specifications were met.

E163046

Use the key blade to start your vehicle and
unlock or lock the driver door from outside
your vehicle. The transmitter portion
functions as the remote control.

The typical operating range for your
transmitter is approximately 33 feet (10
meters). Vehicles with the remote start
feature will have a greater range. One of
the following could cause a decrease in
operating range:
• weather conditions
• nearby radio towers
• structures around the vehicle
• other vehicles parked next to your
vehicle

E163047

Note: Your vehicle’s keys came with a
security label that provides important
vehicle key cut information. Keep the label
in a safe place for future reference.

Replacing the Battery

The radio frequency used by your remote
control can also be used by other short
distance radio transmissions, for example
amateur radios, medical equipment,
wireless headphones, remote controls and
alarm systems. If the frequencies are
jammed, you will not be able to use your
remote control. You can lock and unlock
the doors with the key.

Note: Refer to local regulations when
disposing of transmitter batteries.
Note: Do not wipe off any grease on the
battery terminals or on the back surface of
the circuit board.
Note: Replacing the battery will not delete
the transmitter from the vehicle. The
transmitter should operate normally.

Note: Make sure to lock your vehicle before
leaving it unattended.

The remote control uses one coin-type
three-volt lithium battery CR2032 or
equivalent.

Note: If you are in range, the remote control
will operate if you press any button
unintentionally.
49

F150 (TF6) , enUSA

Keys and Remote Controls
Programming to the Transmitter

Integrated Keyhead Transmitter

With the ignition on, move the memory
features to the desired positions using
the associated controls.

1
3

E163048

3.
4.

5.
6.

Twist a thin coin in the slot of the
transmitter near the key ring to remove
the battery cover.
Carefully peel up the rubber gasket
from the transmitter. It may come off
with the battery cover.
Remove the old battery
Insert the new battery. Refer to the
instructions inside the transmitter for
the correct orientation of the battery.
Press the battery down to make sure
it is fully in the housing.
Reinstall the rubber gasket.
Snap the battery cover back onto the
transmitter.

E162734

2. Press and hold memory button 1 on the
side of the driver seat. A tone will sound
after about two seconds. Continue to
hold until you hear a second tone.
3. Press the lock button on the remote
control within three seconds. A single
tone sounds.
Repeat this procedure with button 2 and
a second remote control if desired.
Deactivating from the Transmitter
1.

Press and hold the desired memory
button for five seconds. A tone will
sound after about two seconds.
Continue to hold until you hear a
second tone.
2. Press the unlock button on the remote
control within three seconds.

Memory Feature (If Equipped)
You can use the remote control to recall
memory settings for the driver seat, power
mirrors, steering column and power foot
pedals.

Repeat this procedure for each additional
transmitter if desired.

Press the unlock button on the remote
control to recall the memory positions. If
you enable the easy-entry and exit feature,
the seat will move to the easy-entry
position. The seat will move to the driver
memory position when you put the key in
the ignition.

Car Finder
Press the button twice within
three seconds. The horn will
E138623
sound and the turn signals will
flash. We recommend you use this method
to locate your vehicle, rather than using
the panic alarm.
50

F150 (TF6) , enUSA

Keys and Remote Controls
Sounding a Panic Alarm

•
•
•

Note: The panic alarm will only operate
when the ignition is off.

E138624

Press the button to activate the
alarm. Press the button again or
turn the ignition on to deactivate

Remote Starting the Vehicle
Note: You must press each button within
three seconds of each other. Your vehicle
will not remote start and the horn will not
sound if you do not follow this sequence.

it.

Remote Start

The transmission is not in P.
The vehicle battery voltage is too low.
The service engine soon indicator is on.

(If Equipped)

WARNING
To avoid exhaust fumes, do not use
remote start if your vehicle is parked
indoors or areas that are not well
ventilated.
Note: Do not use remote start if your vehicle
is low on fuel.

E138626

The label on your transmitter details the
starting procedure.

The remote start button is on the
transmitter.
E138625

To remote start your vehicle:

This feature allows you to start your
vehicle from outside the vehicle. The
transmitter has an extended operating
range.

Press the lock button to lock all the
doors.
2. Press the remote start button twice.
The exterior lamps will flash twice.

Vehicles with automatic climate control
can be set to operate when you remote
start the vehicle. See Climate Control
(page 106). A manual climate control
system will run at the setting it was set to
when you switch the vehicle off.

The horn will sound if the system fails to
start, unless quiet start is on. Quiet start
will run the blower fan at a slower speed
to reduce noise. You can switch it on or off
in the information display. See General
Information (page 87).

Many states and provinces have
restrictions for the use of remote start.
Check your local and state or provincial
laws for specific requirements regarding
remote start systems.

Note: If you remote start your vehicle with
an integrated keyhead transmitter, you must
switch the ignition on before driving your
vehicle. If you remote start your vehicle with
an intelligent access transmitter, you must
press the START/STOP button on the
instrument panel once while applying the
brake pedal before driving your vehicle.

The remote start system will not work if
any of the following occur:
• The ignition is on.
• The alarm system triggers.
• You disable the feature.
• The hood is open.

The power windows will not work during
the remote start and the radio will not turn
on automatically.

F150 (TF6) , enUSA

Keys and Remote Controls
The parking lamps will remain on and the
vehicle will run for 5, 10, or 15 minutes,
depending on the setting.
Extending the Vehicle Run Time
Repeat Steps 1 and 2 with the vehicle still
running to extend the run time for another
remote start duration. If the duration is set
to last 10 minutes, the duration will extend
by another 10 minutes. For example, if the
vehicle had been running from the first
remote start for five minutes, the vehicle
will continue to run now for a total of 20
minutes.
Wait at least five seconds before remote
starting after a vehicle shutdown.
Turning the Vehicle Off After Remote
Starting
Press the button once. The
parking lamps will turn off.
E138625

You may have to be closer to the
vehicle than when starting due to ground
reflection and the added noise of the
running vehicle.
You can disable or enable the remote start
system through the information display.
See General Information (page 87).

REPLACING A LOST KEY OR
REMOTE CONTROL
Replacement keys or remote controls can
be purchased from an authorized dealer.
Authorized dealers can program remote
controls for your vehicle. See Passive
Anti-Theft System (page 61).
To re-program the passive anti-theft
system see an authorized dealer.

F150 (TF6) , enUSA

MyKey™
Configurable Settings

PRINCIPLE OF OPERATION

With an admin key, you can configure
certain MyKey settings when you first
create a MyKey and before you recycle the
key or restart the vehicle. You can also
change the settings afterward with an
admin key:
• A vehicle speed limit can be set.
Warnings will be shown in the display
followed by an audible tone when your
vehicle reaches the set speed. You
cannot override the set speed by fully
depressing the accelerator pedal or by
setting cruise control.
• Vehicle speed minders of 45, 55 or 65
mph (75, 90 or 105 km/h). Once you
select a speed, it will be shown in the
display, followed by an audible tone
when the preselected vehicle speed is
exceeded.
• Audio system maximum volume of
45%. A message will be shown in the
display when you attempt to exceed
the limited volume. Also, the
speed-sensitive or compensated
automatic volume control will be
disabled.
• Always on setting. When this is
selected, you will not be able to turn
off Advance Trac (if your vehicle is
equipped with this feature).

MyKey allows you to program keys with
restricted driving modes to promote good
driving habits. All but one of the keys
programmed to the vehicle can be
activated with these restricted modes.
Any keys that have not been programmed
are referred to as administrator keys or
admin keys. They can be used to:
• create a MyKey
•
•

program configurable MyKey settings
clear all MyKey features.

When you have programmed a MyKey, you
can access the following information using
the information display:
• How many admin keys and MyKeys are
programmed to your vehicle.
• The total distance your vehicle has
traveled using a MyKey.
Note: All MyKeys are programmed to the
same settings. You cannot program them
individually.

Non-configurable Settings
The following settings cannot be changed
by an admin key user:
• Belt-Minder. You cannot disable this
feature. The audio system will mute
when the front seat occupants’ safety
belts are not fastened.
• Early low fuel. The low fuel warning is
activated earlier, giving the MyKey user
more time to refuel.
• Driver assist features, if equipped on
your vehicle, are forced on: parking aid,
blind spot information system (BLIS)
with cross traffic alert, lane departure
warning and forward collision warning
system.
• Satellite radio adult content
restrictions.

CREATING A MYKEY
Use the information display to create a
MyKey. There are two types of information
displays, and their controls and messaging
vary. To determine which type of display
you have, you will need to reference
another chapter. See General
Information (page 87).
If You Have a Type 1 Information
Display:

F150 (TF6) , enUSA

MyKey™
1.
2.
3.

Programming/Changing
Configurable Settings

Insert the key you want to program into
the ignition.
Switch the ignition on.
Access the main menu on the
information display controls. Press
SETUP using the information display
buttons until PRESS RESET TO
CREATE MYKEY is displayed.
Press and release the RESET button.
You will see HOLD RESET TO
CONFIRM MYKEY in the display.
Press and hold the RESET button for
two seconds until you see the message
MARK THIS AS RESTRICTED in the
display. Wait until you see KEY
RESTRICTED AT NEXT START in the
display.

Use the information display to program or
change your configurable MyKey settings.
There are two types of information
displays, and their controls and messaging
vary. To determine which type of display
you have, you will need to reference
another chapter. See General
Information (page 87).
If You Have a Type 1 Information
Display:
1.
2.

If You Have a Type 2 Information
Display:
1.
2.
3.

4.
5.

Insert the key you want to program into
the ignition.
Switch the ignition on.
Access the main menu on the
information display controls, and select
SETTINGS, then MYKEY by pressing
OK or the > button.
Press OK or the > button to select
CREATE A MYKEY.
When prompted, hold the OK button
until you see KEY RESTRICTED AT
NEXT START in the display. The key
will be restricted at the next start.

If You Have a Type 2 Information
Display:
1.

Switch the ignition on using an admin
key.
2. Access the main menu on the
information display controls, and select
SETTINGS, then MYKEY by pressing
OK or the > button.
3. Use the arrow buttons to get to a
configurable feature.
4. Press OK or > to make a selection.

MyKey is successfully created. Make sure
you label it so you can distinguish it from
the admin keys.
You can also program configurable
settings for the key(s). Refer to
Programming/Changing Configurable
Settings.

F150 (TF6) , enUSA

Switch the ignition on using an admin
key.
Access the main menu on the
information display controls, and press
SETUP until RESET FOR MYKEY
SETTINGS displays.
Press and release the RESET button
to display MyKey setup menus.
Press the SETUP button to enter your
choice. Once you make a selection, the
next configurable setting will be
displayed.
Repeat Steps 3 and 4 until you are
done changing the configurable
settings.

MyKey™
Note: You can clear or change your MyKey
settings at any time during the same key
cycle as you created the MyKey. Once you
have switched the engine off, however, you
will need an admin key to change or clear
your MyKey settings.

3. Hold the OK button until ALL
MYKEYS CLEARED displays.

CHECKING MYKEY SYSTEM
STATUS
You can find information about your
programmed MyKeys by using the
information display.

CLEARING ALL MYKEYS
You can clear all MyKeys within the same
key cycle as you created the MyKey. If you
switch your ignition off, however, you will
need to use an admin key to clear your
MyKeys.

MYKEY DISTANCE
Tracks the distance when drivers use a
MyKey. The only way to delete the
accumulated distance is by using an admin
key to clear your MyKey. If the distance
does not accumulate as expected, then
the intended user is not using the MyKey,
or an admin key user recently cleared and
then recreated a MyKey.

Note: When you clear your MyKeys, you
remove all restrictions and return all MyKeys
to their original admin key status at once.
To clear all MyKeys of all MyKey settings,
use the information display. There are two
types of information displays, and their
controls and messaging vary. To determine
which type of display you have, you will
need to reference another chapter. See
General Information (page 87).

NUMBER OF MYKEY(S)
Indicates the number of MyKeys
programmed to your vehicle. Use this
feature to detect how many MyKeys you
have for your vehicle and determine when
a MyKey has been deleted.

If You Have a Type 1 Information
Display:

NUMBER OF ADMIN KEY(S)

Press SETUP until PRESS RESET TO
CLEAR MYKEY displays.
2. Press and release the RESET button.
The display will show HOLD RESET
TO CONFIRM CLEAR.
3. Press and hold the RESET button for
two seconds until ALL MYKEYS
CLEARED displays.

Indicates how many admin keys are
programmed to your vehicle. Use this
feature to determine how many
unrestricted keys you have for your vehicle,
and detect if an additional MyKey has been
programmed.

USING MYKEY WITH REMOTE
START SYSTEMS

If You Have a Type 2 Information
Display:

MyKey is not compatible with non
Ford-approved, aftermarket remote start
systems. If you choose to install a remote
start system, see an authorized dealer for
a Ford-approved remote start system.

Access the main menu and select
SETTINGS, then MYKEY.
2. Scroll to CLEAR ALL and press the OK
button.

F150 (TF6) , enUSA

MyKey™
MYKEY TROUBLESHOOTING
Condition

I cannot create a MyKey.

Potential causes

· The key used to start the vehicle does not
have admin privileges.
· The key used to start the vehicle is the only
admin key. There always has to be at least
one admin key.
· SecuriLock passive anti-theft system is
disabled or in unlimited mode.

I cannot program the configurable settings. · The key in the ignition does not have admin
privileges.
· There are no keys programmed to the
vehicle. See Creating a MyKey (page 53).
I cannot clear the MyKeys.

· The key used to start the vehicle does not
have admin privileges.
· No MyKeys are created. See Creating a
MyKey (page 53).

I lost the only admin key.

· Purchase a new key from your authorized
dealer.

I lost a key.

· Program a spare key. See Passive AntiTheft System (page 61).

MyKey distances do not accumulate.

· The MyKey user is not using the MyKey.
· An admin key holder cleared the MyKeys
and created new MyKeys.
· The key system has been reset.

F150 (TF6) , enUSA

Locks
Locking the Doors

LOCKING AND UNLOCKING
You can use the power door lock control
or the remote control to lock and unlock
your vehicle.

E138623

Press the button to lock all the
doors. The turn signals will
illuminate.

Press the button again within three
seconds to confirm that all the doors are
closed. The doors will lock again, the horn
will sound and the turn signals will
illuminate if all the doors are closed.

Power Door Locks (If Equipped)
The power door lock control is on the driver
and front passenger door panels.

Mislock
If any door is open or if the hood is open on
vehicles with an anti-theft alarm or remote
start, the horn will sound twice and the
lamps will not flash.

Smart Unlocks (If Equipped)

E163049

Unlock

Lock

This feature helps to prevent you from
locking yourself out of your vehicle if your
key is still in the ignition.
When you open the driver door and lock
your vehicle with the power door lock
control, all the doors will lock then unlock
if your key is still in the ignition.

Remote Control (If Equipped)
You can use the remote control at any time
your vehicle is not running.

Your can still lock your vehicle with the key
in the ignition by:
• using the manual lock on the door
• locking the driver door with a key
• using the keyless entry keypad
• using the lock button on the remote
control

Unlocking the Doors (Two-Stage
Unlock)
Press the button to unlock the
driver door.
E138629

Press the button again within
three seconds to unlock all doors. The turn
signals will flash.

Autolock and Autounlock (If Equipped)

Press and hold both the lock and unlock
buttons on the remote control for four
seconds to disable or enable two-stage
unlocking. Disabling two-stage unlocking
allows all vehicle doors to unlock with one
press of the button. The turn signals will
flash twice to indicate a change to the
unlocking mode. The unlocking mode
applies to the remote control and keyless
entry keypad.

The autolock feature will lock all the doors
when:
• all doors are closed, and
• the ignition is on, and
• you shift into any gear putting your
vehicle in motion, and
• your vehicle attains a speed greater
than 12 mph (20 km/h).

F150 (TF6) , enUSA

Locks
Battery Saver

The autolock feature will unlock all the
doors when:
• autolock has locked the doors
• you stop the vehicle and switch the
ignition off or to accessory mode, and
• you open the driver door within 10
minutes.

The battery saver turns off the interior
lamps 30 minutes after you switch the
ignition off if a door is open and the dome
lamp switch is on. It turns off the interior
lamps after 10 minutes if the dome lamp
switch is off.

Note: The doors will not autounlock if you
have electronically locked them before
opening the driver door.

KEYLESS ENTRY (IF EQUIPPED)

Enabling or Disabling

SECURICODE™ KEYLESS ENTRY
KEYPAD

You can enable or disable these features
in the information display or your
authorized dealer can do it for you. See
General Information (page 87).

The keypad is located near the driver
window.
Note: If you enter your entry code too fast
on the keypad, the unlock function may not
work. Re-enter your entry code more slowly.

Note: You can enable or disable the
autolock and autounlock features
independently of each other.

Illuminated Entry
The interior lamps and select exterior
lamps will illuminate when you unlock the
doors with the remote entry system.
The illuminated entry system will turn off
the lights if:
• the ignition is on
• you press the remote control lock
button, or
• after 25 seconds of illumination.

E163050

You can use the keypad to lock or unlock
the doors without using a key.
You can operate the keypad with the
factory-set five-digit entry code. The code
is located on the owner’s wallet card in the
glove box and is available from an
authorized dealer. You can also create up
to five of your own five-digit personal entry
codes.

The dome lamp will not turn on if the
control is set to the off position.
The lights will not turn off if:
•
•

you turn them on with the dimmer
control, or
any door is open.

Programming a Personal Entry Code
To create your own personal entry code:
1. Enter the factory-set code.
2. Press 1·2 on the keypad within five
seconds.

F150 (TF6) , enUSA

Locks
3. Enter your personal 5-digit code. You
must enter each number within five
seconds of each other.
4. Press 1·2 on the keypad to save
personal code 1.

All personal codes will erase and only the
factory-set 5-digit code will work.
Anti-Scan Feature
The keypad will go into an anti-scan mode
if you enter the wrong code seven times
(35 consecutive button presses). This
mode disables the keypad for one minute
and the keypad lamp will flash.

The doors will lock then unlock to confirm
that programming was successful.
To program additional personal entry
codes, repeat Steps 1-3, then for Step 4:
• Press 3·4 to save personal code 2.
• Press 5·6, 7·8 or 9·0 to save personal
code 3.

The anti-scan feature will turn off after:
• One minute of keypad inactivity.
• Pressing the unlock button on the
remote control.
• Switching the ignition on.

You may also program a personal entry
code through the MyFord Touch system.

Unlocking and Locking the Doors

Tips:
• Do not set a code that uses five of the
same number.
• Do not use five numbers in sequential
order.
• The factory-set code will work even if
you have set your own personal code.

To Unlock the Driver Door
Enter the factory-set 5-digit code or your
personal code. You must press each
number within five seconds of each other.
The interior lamps will illuminate.
Note: All doors will unlock if you disable
the two-stage unlocking mode. See
Locking and Unlocking (page 57).

Recalling Memory Positions (If
Equipped)
The programmed entry codes will recall
driver memory positions as follows:
•
•

To Unlock All Doors
Enter the factory-set code or your personal
code, then press 3·4 within five seconds.

Entry code 1 will recall driver 1 memory
positions.
Entry code 2 will recall driver 2 memory
positions.

To Lock All Doors

Note: Personal entry codes 3, 4 and 5 will
not recall memory positions.

Press and hold 7·8 and 9·0 at the same
time (with the driver door closed). You do
not need to enter the keypad code first.

Erasing a Personal Code

Displaying the Factory Set Code

1. Enter the factory-set 5-digit code.
2. Press and release 1·2 on the keypad
within five seconds.
3. Press and hold 1·2 for two seconds.
You must do this within five seconds
of completing Step 2.

Note: You will need to have two
programmed passive anti-theft keys for this
procedure.
To display the factory-set code in the
information display:
1.

F150 (TF6) , enUSA

Insert a key into the ignition and switch
the ignition on for a few seconds.

Locks
2. Switch the ignition off and remove the
key.
3. Within ten seconds, insert the second
key into the ignition and switch the
ignition on.
The factory-set code will display for a few
seconds.
Note: The code may not display until after
any other warning messages first display.

F150 (TF6) , enUSA

Security
PASSIVE ANTI-THEFT
SYSTEM (IF EQUIPPED)

Replacement Keys

Note: The system is not compatible with
non-Ford aftermarket remote start systems.
Use of these systems may result in vehicle
starting problems and a loss of security
protection.

The integrated keyhead transmitter
functions as a programmed ignition key. It
operates all the locks, starts the vehicle
and acts as a remote control.

Note: Your vehicle may have two integrated
keyhead transmitters.

If your programmed transmitters or
standard SecuriLock coded keys are lost
or stolen and you do not have an extra
coded key, you will need to have your
vehicle towed to an authorized dealer. You
need to erase the key codes from your
vehicle and program new coded keys.

Note: Metallic objects, electronic devices
or a second coded key on the same key
chain may cause vehicle starting problems
if they are too close to the key when starting
the engine. Prevent these objects from
touching the coded key while starting the
engine. Switch the ignition off, move all
objects on the key chain away from the
coded key and restart the engine if a
problem occurs.

Store an extra programmed key away from
your vehicle in a safe place to help prevent
any inconveniences. See an authorized
dealer to purchase additional spare or
replacement keys.

Note: Do not leave a duplicate coded key
in the vehicle. Always take your keys and
lock all doors when leaving the vehicle.

Programming a Spare Key

SecuriLock™

Note: You can program a maximum of eight
coded keys to your vehicle. Only four of
these can be integrated keyhead
transmitters.

The system is an engine immobilization
system. It helps prevent the engine from
starting unless you use a coded key
programmed to your vehicle. Using the
wrong key may prevent the engine from
starting. A message may appear in the
information display.

You can program your own integrated
keyhead transmitter or standard
SecuriLock coded keys to your vehicle. This
procedure will program both the engine
immobilizer keycode and the remote entry
portion of the remote control to your
vehicle.

If you are unable to start the engine with a
correctly coded key, the system has
malfunctioned. A message may appear in
the information display.

Only use integrated keyhead transmitters
or standard SecuriLock keys.

Automatic Arming

You must have two previously
programmed coded keys and the new
unprogrammed key readily accessible. See
an authorized dealer to have the spare key
programmed if two previously
programmed coded keys are not available.

The system arms immediately after you
switch the ignition off.
Automatic Disarming
Switching the ignition on with a coded key
disarms the system.

Read and understand the entire procedure
before you begin.

F150 (TF6) , enUSA

Security
1.
2.

3.
4.

Insert the first previously programmed
coded key into the ignition.
Switch the ignition from off to on. Keep
the ignition on for at least three
seconds, but no more than 10 seconds.
Switch the ignition off and remove the
first coded key from the ignition.
After three seconds but within 10
seconds of switching the ignition off,
insert the second previously coded key
into the ignition.
Switch the ignition from off to on. Keep
the ignition on for at least three
seconds, but no more than 10 seconds.
Switch the ignition off and remove the
second previously programmed coded
key from the ignition.
After three seconds but within 10
seconds of switching the ignition off
and removing the previously
programmed coded key, insert the new
unprogrammed key into the ignition.
Switch the ignition from off to on. Keep
the ignition on for at least six seconds
until you hear the door locks cycle.
Remove the newly programmed coded
key from the ignition.

The direction indicators flash and the horn
sounds if the system triggers while the
alarm is armed.
Take all remote controls to an authorized
dealer if there is any potential alarm
problem with your vehicle.

Arming the Alarm
The alarm is ready to arm when there is
not a key in the ignition. Electronically lock
the vehicle to arm the alarm.
The direction indicators flash once after
you lock the vehicle. This indicates the
alarm is in the pre-armed mode. It will fully
arm in 20 seconds.

Disarming the Alarm
Disarm the alarm by any of the following
actions:
•
•
•
•

The key will start the engine if
programming is successful. You can
operate the remote entry system if the new
key is an integrated keyhead transmitter.

Note: Pressing the panic button on the
remote control will stop the horn and signal
indicators, but will not disarm the system.

If programming was not successful, wait
20 seconds and repeat Steps 1 through 8.
If you are still unsuccessful, take your
vehicle to an authorized dealer.

ANTI-THEFT ALARM (IF EQUIPPED)
The system warns you of an unauthorized
entry to your vehicle. It triggers if any door
or the hood opens without using the key,
remote control or keyless entry keypad.

F150 (TF6) , enUSA

Press the power door unlock button
within the 20-second pre-armed mode.
Unlock the doors with the remote
control or keyless entry keypad.
Switch the ignition on or start the
vehicle.
Use a key in the driver door to unlock
the vehicle, then switch the ignition on
within 12 seconds.

Power Running Boards (If Equipped)
Automatic Power Deploy

USING POWER RUNNING
BOARDS
WARNINGS
In extreme climates, excessive ice
buildup may occur, causing the
running boards not to deploy. Make
sure that the running boards have
deployed, and have finished moving before
attempting to step on them. The running
boards will resume normal function once
the blockage is cleared.

E166682

Turn off the running boards before
jacking or placing any object under
your vehicle. Never place your hand
between the extended running board and
your vehicle. A moving running board may
cause injury.

The running boards automatically extend
down and out when you open the door.
This can help you enter and exit your
vehicle.

Automatic Power Stow

Note: Do not use the running boards, front
and rear hinge assemblies, running board
motors, or the running board underbody
mounts to lift your vehicle when jacking.
Always use proper jacking points.

When you close the doors, the running
boards return to the stowed position after
a two-second delay.

Note: The running boards may operate
more slowly in cool temperatures.

You can manually operate the running
boards in the information display. See
General Information (page 87).

Manual Power Deploy

Note: The running board mechanism may
trap debris such as mud, dirt, snow, ice and
salt. This may cause unwanted noise. If this
happens, manually set the running boards
to the deployed position. Then, wash the
system, in particular the front and rear hinge
arms, with a high-pressure car wash wand.

Set the running boards in the deployed
position (OUT) to access the roof.
The running boards return to the stowed
position and enter automatic mode when
the vehicle speed exceeds 5 mph (8 km/h).

Enabling and Disabling
You can enable and disable the power
running board feature in the information
display. See General Information (page
87).

F150 (TF6) , enUSA

Power Running Boards (If Equipped)
•

•

When disabled (OFF), the running
boards move to the stowed position
regardless of the door position.
When enabled (AUTO), the running
boards move back to the correct
positions based on the door position.

Bounce-back
The running board will reverse direction
and move to the end of travel if it
encounters an object while moving.

F150 (TF6) , enUSA

Steering Wheel
ADJUSTING THE STEERING
WHEEL
WARNING
Do not adjust the steering wheel
when your vehicle is moving.
Note: Make sure that you are sitting in the
correct position. See Sitting in the Correct
Position (page 114).

3
E95179

3. Lock the steering column.

Power Tilt and Telescope Steering
Column (If Equipped)
WARNING
Do not adjust the steering wheel
when your vehicle is moving.

2
Note: Make sure that you are sitting in the
correct position. See Sitting in the Correct
Position (page 114).

E95178

1. Unlock the steering column.
Note: The telescopic adjustment is an
optional feature.
2. Adjust the steering wheel to the desired
position.

F150 (TF6) , enUSA

Steering Wheel
AUDIO CONTROL (IF EQUIPPED)
You can operate the following functions
with the control:

Type 1

B
C

E161834

Use the control on the side of the steering
column to adjust the position.

E166635

To adjust:
• tilt: press the top or bottom of the
control
• telescope: press the front or rear of the
control.

Volume up

Seek up or next

Media

Seek down or previous

Volume down

Memory Feature

Type 2

You can save and recall the steering
column position with the memory function.
See Memory Function (page 118).
Pressing the adjustment control during
memory recall cancels the operation. The
column responds to the adjustment
control.

A
E
D

Easy Entry and Exit Feature
The column moves to the full up and in
position when you switch the ignition off.
It returns to the previous setting when you
switch the ignition on. You can enable or
disable this feature in the information
display.

C
E166636

F150 (TF6) , enUSA

Volume up

Seek up or next

Media

Steering Wheel
D

Seek down or previous

Volume down

CRUISE CONTROL (IF EQUIPPED)

Media
Press repeatedly to scroll through available
audio modes.

Seek, Next or Previous
E166638

Press the seek button to:
• Tune the radio to the next or previous
stored preset.
• Play the next or previous track.

See Cruise Control (page 176).

INFORMATION DISPLAY
CONTROL

Press and hold the seek button to:
• Tune the radio to the next station up
or down the frequency band.
• Seek through a track.

Type 1

VOICE CONTROL (IF EQUIPPED)

E166639

Type 2

E166637

Voice recognition

Phone mode

Confirm selection

See SYNC™ (page 323). See MyFord
Touch™ (page 359).

E166640

See Information Displays (page 87).

F150 (TF6) , enUSA

Pedals
ADJUSTING THE PEDALS (IF
EQUIPPED)

Note: Never use the controls while your feet
are on the accelerator and brake pedals and
the vehicle is moving.
You can find the control on the left side of
the steering column. Press and hold the
appropriate side of the control to move the
pedals.

E162916

A. Farther
B. Closer
You can save and recall the pedal positions
with the memory feature. See Memory
Function (page 118).
Note: Adjust the pedals only when your
vehicle is in P (Park).

F150 (TF6) , enUSA

Wipers and Washers
WINDSHIELD WIPERS

AUTOWIPERS (IF EQUIPPED)

Note: Fully defrost the windshield before
switching on the windshield wipers.

Note: Make sure you switch off the wipers
before entering a car wash.

Note: Make sure you switch off the
windshield wipers before entering a car
wash.

Note: Wet or winter driving conditions with
ice, snow or salty road mist can cause
inconsistent and unexpected wiping or
smearing.

Note: Clean the windshield and wiper
blades if they begin to leave streaks or
smears. If that does not resolve the issue,
install new wiper blades.

In these conditions, you can do the
following to help keep your windshield
clear:
• Lower the sensitivity of the autowipers.
• Change the wiper speed to normal or
high-speed wipe as necessary.
• Switch the autowipers off.

Note: Do not operate the wipers on a dry
windshield. This may scratch the glass,
damage the wiper blades or cause the wiper
motor to burn out. Always use the
windshield washers before wiping a dry
windshield.

The autowipers feature uses a rain sensor,
located in the area around the interior
mirror. The rain sensor monitors the
amount of moisture on the windshield and
automatically turns on the wipers. It will
adjust the wiper speed by the amount of
moisture that the sensor detects on the
windshield. You can switch this feature on
or off in the information display. See
Information Displays (page 87).

E172816

Rotate the end of the control:
•
•

Away from you to increase the wiper
speed.
Toward you to decrease the wiper
speed.

Speed dependent wipers (if
equipped)

E172817

When your vehicle speed increases, the
interval between wipes decreases.

F150 (TF6) , enUSA

Wipers and Washers
A wipe will occur a few seconds after
washing to clear any remaining washer
fluid. You can switch this feature on or off
in the information display. See
Information Displays (page 87).

Use the rotary control to adjust the
sensitivity of the rain sensor. With low
sensitivity, the wipers will operate when
the sensor detects a large amount of
moisture on the windshield. With high
sensitivity, the wipers will operate when
the sensor detects a small amount of
moisture on the windshield.
Keep the outside of the windshield clean
because the rain sensor is very sensitive. If
the area around the interior mirror is dirty,
then the wipers may turn on, for example,
if dirt, mist or insects hit the windshield.

WINDSHIELD WASHERS
Note: Do not operate the wipers on a dry
windshield. This may scratch the glass,
damage the wiper blades or cause the wiper
motor to burn out. Always use the
windshield washer before wiping a dry
windshield.
Note: Do not operate the washers when
the washer reservoir is empty. This may
cause the washer pump to overheat.

E172818

•
•

•

A brief press causes a single wipe
without washer fluid.
A brief press and hold causes the
wipers to swipe three times with
washer fluid.
A long press and hold will turn on the
wipers and washer fluid for up to 10
seconds.
70

F150 (TF6) , enUSA

Lighting
Headlamp Flasher

LIGHTING CONTROL

E163268

E163267

•

Pull the lever toward you to flash the
headlamps and release the lever to switch
the headlamps off.

Rotate the headlamp control clockwise
to the first position to turn on the
parking lamps, instrument panel lamps,
license plate lamps and tail lamps.
Rotate clockwise to the second
position to also turn on the headlamps.

AUTOLAMPS (IF EQUIPPED)

High Beams

E163269

The autolamp system provides light
sensitive automatic on-off control of the
exterior lights normally controlled by the
headlamp control.

E167827

Push the lever toward the instrument panel
to switch the high beams on.

The autolamp system also keeps the lights
on for a predetermined amount of time
after the ignition switch is turned to off.
Using the message center, you can select
a delay from 0–180 seconds.

Push the lever toward the instrument panel
again or pull the lever towards you to
switch the high beams off.

F150 (TF6) , enUSA

Lighting
•
•

To turn autolamps on, rotate the
control to the fourth position.
To turn autolamps off, rotate the
control to the first, second, or third
position.

DAYTIME RUNNING LAMPS (IF
EQUIPPED)

WARNING
Always remember to switch your
headlamps on in low light situations
or during inclement weather. The
system does not activate the tail lamps
and may not provide adequate lighting
during these conditions. Failure to activate
your headlamps under these conditions
may result in a collision.

INSTRUMENT LIGHTING
DIMMER

The system turns the headlamps on with
a reduced intensity output (halogen
headlamps) or turns the front turn lamps
on (HID headlamps) in daylight conditions.
To switch the system on:
1. Ignition switch is in the on position.
2. Switch the lighting control to the off,
autolamp or parking lamp position.

E166125

Use the instrument lighting dimmer control
to adjust the brightness of the instrument
panel and all applicable lit components in
your vehicle.
•

•

FRONT FOG LAMPS (IF EQUIPPED)

Tap the left or right of the control to
the first detent to brighten or dim all
interior lit components incrementally.
Press and hold the left or right of the
control to the first detent until the
desired lighting level is reached.
Press and hold the right of the control
to the second detent to switch the
interior lights on.
Press and hold the left of the control
to the second detent to switch the
interior lights off.

E163271

The headlamp control also operates the
fog lamps. The fog lamps can be turned
on only when the headlamp control is in
the parking lamp (second) position,
headlamps on (third) position, or autolamp
(fourth) position, and the high beams are
not turned on.

F150 (TF6) , enUSA

Lighting
Pull headlamp control towards you to turn
fog lamps on. The fog lamp indicator light
will illuminate.

INTERIOR LAMPS
Front Row Map Lamps (if
equipped)

DIRECTION INDICATORS

E166237

To switch on the map lamps, press the
outer edge of the clear lens.

E163272

The turn signal lever does not mechanically
lock in the upward or downward position
when activated. The turn signal control
activation and cancellation is electronic.
•
•
•

The front row map lamp will automatically
turn on when:
•
•

To operate the left turn signal, push the
lever down until it stops and release.
To operate the right turn signal, push
the lever up until it stops and release.
To manually cancel turn signal
operation, push the lever again in either
direction.

•

Any door is opened.
You press and hold the instrument
panel dimmer switch to the right past
the second detent.
Any of the remote entry controls are
pressed and the ignition is in the off
position.

Rear Dome Lamp (If Equipped)

Lane Change
To indicate a left or right lane change:
•

•

Push the lever up/down to the first
stop position and release. The turn
signals will flash three times and stop.
Push the lever up/down to the first
stop position and hold. The turn signals
will flash for as long as the lever is held
in this position.
E166238

The rear dome lamp can be turned on or
off by sliding the control.

F150 (TF6) , enUSA

Lighting
•
•

•

Rear Courtesy, Reading, Cargo
Lamps (If Equipped)

ON: The dome light will stay on.
DOOR or middle position: The dome
light will only come on if a door is
opened.
OFF: The lamp will not come on at all.

Rear Dome, Courtesy Lamps (If
Equipped)

E166240

You can press the dimmer switch until the
rear lamps come on, or when any door is
opened. The lamps can be turned on or off
by sliding the control.
•

E166239

The dome lamp lights when:
•
•

•

Any door is opened.
You press the instrument panel dimmer
switch until the courtesy lamp turns
on.
You press any of the remote entry
controls and the ignition is off.

•
•

Note: You can only turn the reading portion
and the two outer lights on and off at the
lamp.

F150 (TF6) , enUSA

When the control is in the middle
position, the lamp will come on when
a door is opened or the unlock button
is pressed on the remote keyless entry.
If the control is moved to the left
position, the lamp will stay on.
If the control is moved to the right
position, the lamp will not come on at
all.

Windows and Mirrors
Note: Perform one-touch up re-calibration
with the door closed. Calibrating with the
door open will cause the window to
continuously bounce back.

POWER WINDOWS (IF EQUIPPED)
WARNINGS
Do not leave children unattended in
your vehicle and do not let them play
with the power windows. They may
seriously injure themselves.

To reset the function after the battery
recharges:
1. Pull the switch all the way up.
2. Hold the switch until the glass stops
and continue to hold for two seconds.
3. Press the switch down and operate the
window to the full down position.
One-touch up will now be functional.

When closing the power windows,
you should verify they are free of
obstructions and make sure that
children and pets are not in the proximity
of the window openings.

Bounce-Back (If Equipped)
The window will stop automatically while
closing. It will reverse some distance if
there is an obstacle in the way.
Overriding the Bounce-Back Feature
WARNING

E163056

When you override the bounce-back
feature, the window will not reverse
if it detects an obstacle. Take care
when closing the windows to avoid
personal injury or damage to your vehicle.

Note: You may hear a pulsing noise when
just one of the windows is open. Lower the
opposite window slightly to reduce this
noise.
Press the switch to open the window.

Pull up the window switch and hold within
two seconds of the window reaching the
bounce-back position. The window will
travel up with no bounce-back protection.
The window will stop if you release the
switch before the window closes fully.

Lift the switch to close the window.

One-Touch Up or Down (If Equipped)
Press or lift the switch fully and release it.
Press or lift it again to stop the window.
Note: The window may disable for up to
five minutes if you cycle it up and down
repeatedly. This helps prevent damage to
the motor. Normal operation will resume
once the motor cools.
Restoring the One-Touch Up Function
You may lose the one-touch function if the
vehicle battery is low.

F150 (TF6) , enUSA

Windows and Mirrors
Window Lock (If Equipped)

Press and hold the control to open the
window. Pull and hold the control to close
the window.

Accessory Delay (If Equipped)

E163057

You can use the window switches for
several minutes after you switch the
ignition off or until you open either front
door.

Unlock

EXTERIOR MIRRORS

Lock

Power Exterior Mirrors

Press the control to lock or unlock the rear
window controls.

WARNING
Do not adjust the mirrors when your
vehicle is moving.

Power Sliding Back Window (If
Equipped)

WARNINGS
When operating the power sliding
back window, you must make sure
all rear seat occupants and cargo are
not in the proximity of the back window.

Do not leave children unattended in
your vehicle and do not let them play
with the power sliding back window.
They may seriously injure themselves.

E163059

Left mirror

Off

Right mirror

To adjust your mirrors:
1. Select the mirror you want to adjust.
2. Move the control in the direction you
want to tilt the mirror.
3. Return the control to the center
position to lock the mirrors in place.
E163058

The control is on the overhead console.

F150 (TF6) , enUSA

Windows and Mirrors
Fold-Away Exterior Mirrors

Heated Exterior Mirrors

Push the mirror toward the door window
glass. Make sure that you fully engage the
mirror in its support when returning it to its
original position.

See Heated Windows and Mirrors (page
112).

Power-Folding Mirrors (If Equipped)

You can save and recall the mirror
positions through the memory function.
See Memory Function (page 118).

Memory Mirrors

(If Equipped)

Auto-dimming Feature (if
equipped)
The driver exterior mirror automatically
dims when the interior auto-dimming
mirror turns on.
E163060

Signal Indicator Mirrors

Note: Moving the mirrors 10 or more times
within one minute, or repeated folding and
unfolding of the mirrors while holding the
control down during full travel, may disable
the system to protect the motors from
overheating. Wait approximately three
minutes with the vehicle running, and up to
10 minutes with the vehicle off, for the
system to reset and for function to return to
normal.

(If Equipped)

The rear-facing portion of the appropriate
mirror housing will blink when you switch
on the turn signal.

Clearance Lamps

(If Equipped)

The lower, outer part of the mirror housings
light when you switch the headlamps or
parking lamps on.

Pull the control back to fold the mirrors in
or out.

Telescoping Mirrors

(If Equipped)

Loose Mirror
You can manually fold a power-folding
mirror by pulling it toward the door window
glass. This may cause the mirror to appear
loose and it will need to be
re-synchronized. Pull and hold the control
to fold the mirrors in until the movement
stops. You will hear a click that indicates
re-synchronization. If you do not hear a
click, use the control to fold the mirrors all
the way out, then in again. Once you hear
the click, the mirrors will operate normally
until you fold them manually again.

E163061

This feature lets you extend the mirror
about 3 inches (75 millimeters). It is useful
when towing a trailer. You can manually
pull out or push in the mirrors to the desired
position.

F150 (TF6) , enUSA

Windows and Mirrors
PowerScope™ Power Telescoping
Mirrors (If Equipped)
This feature lets you position both mirrors
at the same time. The switch is on the door
trim panel.

E163062

Telescope Out

Telescope In

Press and hold the switch to move the
mirrors.

When you fully extend the mirrors, you will
hear the motors running as long as you
hold the switch.

E138665

The image of the approaching vehicle is
small and near the inboard edge of the
main mirror when it is at a distance. The
image becomes larger and begins to move
outboard across the main mirror as the
vehicle approaches (A). The image will
transition from the main mirror and begin
to appear in the blind spot mirror as the
vehicle approaches (B). The vehicle will
transition to your peripheral field of view
as it leaves the blind spot mirror (C).

Integrated Blind Spot Mirror (If
Equipped)
WARNING
Objects in the blind spot mirror are
closer than they appear.
Blind spot mirrors have an integrated
convex mirror built into the upper outboard
corner of the exterior mirrors. They can
assist you by increasing visibility along the
side of your vehicle. The blind spot mirror
is only on the driver exterior mirror.

INTERIOR MIRROR

Check the main mirror first before a lane
change, then check the blind spot mirror.
If no vehicles are present in the blind spot
mirror and the traffic in the adjacent lane
is at a safe distance, signal that you are
going to change lanes. Glance over your
shoulder to verify traffic is clear, and
carefully change lanes.

WARNING
Do not adjust the mirror when your
vehicle is moving.

F150 (TF6) , enUSA

Windows and Mirrors
Illuminated Vanity Mirror (If Equipped)

Note: Do not clean the housing or glass of
any mirror with harsh abrasives, fuel or other
petroleum or ammonia-based cleaning
products.
You can adjust the interior mirror to your
preference. Some mirrors also have a
second pivot point. This lets you move the
mirror head up or down and from side to
side.
Pull the tab below the mirror toward you
to reduce glare at night.

Auto-Dimming Mirror (If Equipped)

E162197

Lift the cover to switch the lamp on.

Note: Do not block the sensors on the front
and back of the mirror. Mirror performance
may be affected. A rear center passenger or
raised rear center head restraint may also
block light from reaching the sensor.

MOONROOF (IF EQUIPPED)
WARNINGS
Do not let children play with the
moonroof or leave them unattended
in the vehicle. They may seriously
hurt themselves.

The mirror will dim automatically to reduce
glare when bright lights are detected from
behind your vehicle. It will automatically
return to normal reflection when you select
reverse gear to make sure you have a clear
view when backing up.

When closing the moonroof, you
should verify that it is free of
obstructions and make sure that
children and pets are not in the proximity
of the roof opening.

SUN VISORS
Slide-on-rod (If Equipped)

You can manually open or close the sliding
shade when the moonroof is closed. Pull
the shade toward the front of your vehicle
to close it.
The moonroof controls are located on the
overhead console and have a one-touch
open and close feature. To stop it during
one-touch operation, press the control a
second time.
E138666

Rotate the sun visor toward the side
window and extend it rearward for extra
shade.

F150 (TF6) , enUSA

Windows and Mirrors
Opening and Closing the Moonroof

E163063

Press and release the SLIDE control to
open the moonroof. The moonroof will
stop short of the fully opened position.
Note: This position helps to reduce wind
noise or rumbling which may happen with
the moonroof fully open. Press and release
the control again to fully open the
moonroof.
Pull and release the SLIDE control to close
the moonroof.

Bounce-Back
The moonroof will stop automatically
while closing. It will reverse some distance
if there is an obstacle in the way.
Pull and hold the SLIDE control within two
seconds of a bounce-back event to
override this function. While bounce-back
is active, the closing force increases for
each of the next three times that you close
the moonroof.

Venting the Moonroof
Press and release the TILT control to vent
the moonroof. Pull and hold the TILT
control to close the moonroof.

F150 (TF6) , enUSA

Instrument Cluster
GAUGES

E166919

Engine oil pressure gauge

Engine coolant temperature gauge

Fuel gauge

Transmission fluid temperature gauge

Speedometer

Information display See General Information (page 87).

Tachometer

F150 (TF6) , enUSA

Instrument Cluster
Engine Oil Pressure Gauge

can be caused by special operation
conditions (i.e. snowplowing, towing or
off-road use). Refer to Special operating
conditions in the scheduled maintenance
information for instructions. Operating the
transmission for extended periods of time
with the gauge in the higher than normal
area may cause internal transmission
damage. Altering the severity of the driving
conditions is recommended to lower the
transmission temperature into the normal
range. If the gauge continues to show high
temperatures, see your authorized dealer.

Indicates engine oil pressure. The needle
should stay in the normal operating range
(between L and H). If the needle falls
below the normal range, stop the vehicle,
turn off the engine and check the engine
oil level. Add oil if needed. If the oil level is
correct, have your vehicle checked by your
authorized dealer.

Engine Coolant Temperature
Gauge
WARNING

Information Display

Never remove the coolant reservoir
cap while the engine is running or hot.

Odometer
Located in the bottom of the information
display Registers the accumulated
distance your vehicle has traveled.

Indicates engine coolant temperature. At
normal operating temperature, the level
indicator will be in the normal range. If the
engine coolant temperature exceeds the
normal range, stop the vehicle as soon as
safely possible, switch off the engine and
let the engine cool.

Trip Computer
See General Information (page 87).
Vehicle Settings and Personalization
See General Information (page 87).

Fuel Gauge
Switch the ignition on. The fuel gauge will
indicate approximately how much fuel is
left in the fuel tank. The fuel gauge may
vary slightly when your vehicle is moving
or on a gradient. The arrow adjacent to the
fuel pump symbol indicates on which side
of the vehicle the fuel filler door is located.

WARNING LAMPS AND
INDICATORS
The following warning lamps and
indicators will alert you to a vehicle
condition that may become serious. Some
lamps will illuminate when you start your
vehicle to make sure they work. If any
lamps remain on after starting your vehicle,
refer to the respective system warning
lamp for further information.

Transmission Fluid Temperature
Gauge
Indicates transmission fluid temperature.
At normal operating temperature, the level
indicator will be in the normal range. If the
transmission fluid temperature exceeds
the normal range, stop the vehicle as soon
as safely possible and verify the airflow is
not restricted such as snow or debris
blocking airflow through the grill. Also,
higher than normal operating temperature

Note: Some warning indicators appear in
the information display and function the
same as a warning lamp but do not display
when you start your vehicle.

F150 (TF6) , enUSA

Instrument Cluster
Anti-Lock Braking System

Check 4X4 (If Equipped)

If it illuminates when you are
driving, this indicates a
malfunction. You will continue
to have the normal braking system
(without ABS) unless the brake system
warning lamp is also illuminated. Have the
system checked by your authorized dealer.

Illuminates with the message
CHECK 4X4 when a four-wheel
drive fault is present. See Using
Four-Wheel Drive (page 153).

Cruise Control (If Equipped)

Battery
E71340

If it illuminates while driving, it
indicates a malfunction. Switch
off all unnecessary electrical
equipment and have the system checked
by your authorized dealer immediately.

Direction Indicator
Illuminates when the left or right
turn signal or the hazard warning
flasher is turned on. If the
indicators stay on or flash faster, check for
a burned out bulb.

Brake System

E144522

Illuminates when you switch this
feature on. See Using Cruise
Control (page 176).

Illuminates when you engage the
parking brake with the ignition
on.

Door Ajar
Displays when the ignition is on
and any door is not completely
closed.

If it illuminates when you are driving, check
that the parking brake is not engaged. If
the parking brake is not engaged, this
indicates low brake fluid level or a brake
system malfunction. Have the system
checked immediately by your authorized
dealer.

Electronic Locking Differential
Illuminates when using the
electronic locking differential.

WARNING

E163170

Driving your vehicle with the warning
lamp on is dangerous. A significant
decrease in braking performance
may occur. It will take you longer to stop
your vehicle. Have your vehicle checked by
your authorized dealer immediately. Driving
extended distances with the parking brake
engaged can cause brake failure and the
risk of personal injury.

Engine Coolant Temperature
Illuminates when the engine
coolant temperature is high.
Stop the vehicle as soon as
possible, switch off the engine and let cool.

Engine Oil
If it illuminates with the engine
running or when you are driving,
this indicates a malfunction.
Stop your vehicle as soon as it is safe to
do so and switch the engine off. Check the
engine oil level. See Engine Oil Check
(page 240).
83

F150 (TF6) , enUSA

Instrument Cluster
Note: Do not resume your journey if it
illuminates despite the level being correct.
Have the system checked by your authorized
dealer immediately.

It will also illuminate momentarily when
you switch the ignition on to confirm the
lamp is functional. If it does not illuminate
when you switch the ignition on, or begins
to flash at any time, have the system
checked by your authorized dealer.

Fasten Safety Belt
It will illuminate and a chime will
sound to remind you to fasten
your safety belt.

Powertrain Malfunction/Reduced
Power/Electronic Throttle Control
Illuminates when a powertrain
or an AWD fault has been
detected. Contact your
authorized dealer as soon as possible.

Front Airbag
If it fails to illuminate when you
start your vehicle, continues to
flash or remains on, it indicates
a malfunction. Have the system checked
by your authorized dealer.

Service Engine Soon
If the service engine soon
indicator light stays illuminated
after the engine is started, it
indicates that the On-Board Diagnostics
(OBD-II) system has detected a
malfunction of the vehicle emissions
control system. Refer to On-Board
Diagnostics (OBD-II) in the Fuel and
Refueling chapter for more information
about having your vehicle serviced. See
Emission Control System (page 144).

High Beam
Illuminates when you switch the
high beam headlamps on. It will
flash when you use the
headlamp flasher.

Hill Descent (If Equipped)
Illuminates when hill descent is
switched on.

If the light is blinking, engine misfire is
occurring which could damage your
catalytic converter. Drive in a moderate
fashion (avoid heavy acceleration and
deceleration) and have your vehicle
serviced immediately.

E163171

Low Fuel Level
Illuminates when the fuel level
is low or the fuel tank is nearly
empty. Refuel as soon as

Low Tire Pressure Warning

Note: Under engine misfire conditions,
excessive exhaust temperatures could
damage the catalytic converter or other
vehicle components.

Illuminates when your tire
pressure is low. If the lamp
remains on with the engine
running or when driving, check
your tire pressure as soon as possible.

The service engine soon indicator light
illuminates when the ignition is first turned
on prior to engine start to check the bulb
and to indicate whether the vehicle is ready
for Inspection/Maintenance (I/M) testing.

possible.

F150 (TF6) , enUSA

Instrument Cluster
4X4 Auto (If Equipped)

Normally, the service engine soon light will
stay on until the engine is cranked, then
turn itself off if no malfunctions are
present. However, if after 15 seconds the
service engine soon light blinks eight times,
it means that the vehicle is not ready for
I/M testing. See Emission Control
System (page 144).

Illuminates when the four-wheel
drive system is engaged. If the
E166922
light fails to display when the
ignition is turned on, or remains on, have
the system serviced immediately by your
authorized dealer.

Traction and Stability Control

4X4 LOW (If Equipped)

Illuminates when the system is
active. If it remains illuminated
E138639
or does not illuminate when you
switch the ignition on, this indicates a
malfunction. During a malfunction the
system will switch off. Have the system
checked by your authorized dealer
immediately. See Using Stability
Control (page 168).

Illuminates when four-wheel
drive low is engaged. If the light
E163174
fails to display when the ignition
is turned on, or remains on, have the
system serviced immediately by your
authorized dealer.

4X4 HIGH (If Equipped)
Illuminates when four-wheel
drive high is engaged. If the light
E163175
fails to display when the ignition
is turned on, or remains on, have the
system serviced immediately by your
authorized dealer.

Traction and Stability Control Off
Illuminates when you switch the
system off. It will go out when
you switch the system back on
or when you switch the ignition off. See
Using Stability Control (page 168).

AUDIBLE WARNINGS AND
INDICATORS

Transmission Tow/Haul (If Equipped)
Illuminates when the tow/haul
feature has been activated. If the
E161509
light flashes steadily, have the
system serviced immediately, damage to
the transmission could occur. See
Automatic Transmission (page 147).

Headlamps On Warning Chime
Sounds when you remove the key from the
ignition and open the driver's door and you
have left the headlamps or parking lamps
on.

4X2 (If Equipped)

Key in Ignition Warning Chime

Illuminates momentarily when
two-wheel drive high is selected.
E163173
If the light fails to display when
the ignition is turned on, or remains on,
have the system serviced immediately by
your authorized dealer.

Sounds when you open the driver's door
and you have left the key in the ignition
with it in the off or accessory position.

F150 (TF6) , enUSA

Instrument Cluster
Parking Brake On Warning Chime
Sounds when you have left the parking
brake on and drive your vehicle. If the
warning chime remains on after you have
released the parking brake, have the
system checked by your authorized dealer
immediately.

F150 (TF6) , enUSA

Information Displays
Information Display Controls
(Type 1)

GENERAL INFORMATION
WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any handheld device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.
Various systems on your vehicle can be
controlled using the information display
controls on the steering wheel.
Corresponding information is displayed in
the information display.

E166920

•

Press the INFO button to scroll through
trip, fuel usage, trailer gain and MyKey®
information.
Press the SETUP button to scroll
through various vehicle feature
settings.
Press the RESET button to choose
settings, reset information and confirm
messages.

Info
Press the INFO button repeatedly to cycle
through the following features:
Note: Some options may appear slightly
different or not at all if the items are
optional.

F150 (TF6) , enUSA

Information Displays

INFO

TRIP A or B
MYKEY MILES (km) (if programmed)
MILES (km) TO E
AVG MPG (L/100km)
MPG (L/km)
TIMER
TBC GAIN (if equipped)
Blank
AVG MPG (L/100km)

TRIP A or B

Average fuel economy displays your
average fuel economy in miles/gallon or
liters/100 km.

Registers the distance of individual
journeys. Press and release the INFO
button until TRIP A or B appears in the
display (this represents the trip mode).
Press and hold the RESET button to reset.

MPG (L/km)
Displays the instantaneous fuel economy
as a bar graph. Your vehicle must be
moving to calculate instantaneous fuel
economy. Instantaneous fuel economy
cannot be reset.

MYKEY MILES (km)
For more information, See Principle of
Operation (page 53).
MILES (km) TO E

TIMER

This displays an estimate of approximately
how far you can drive with the fuel
remaining in your tank under normal driving
conditions. Remember to turn the ignition
off when refueling to allow this feature to
correctly detect the added fuel.

Displays the trip elapsed drive time. Press
and release RESET to pause the timer.
Press and hold RESET to reset the timer.
TBC GAIN
Displays the level of trailer brake gain or if
the trailer is not connected.

Distance to empty is calculated using a
running average fuel economy, which is
based on your recent driving history of 500
miles (800 km).

System check and vehicle feature
customization

This value is not the same as the average
fuel economy display. The running average
fuel economy is re-initialized to a factory
default value if the battery is disconnected.

Press the SETUP button repeatedly to
cycle the information display through the
following features:

F150 (TF6) , enUSA

Information Displays
Note: Some options may appear slightly
different or not at all if the items are
optional.

Note: When returning to the SETUP menu
and a non-English language has been
selected, HOLD RESET FOR ENGLISH will
be displayed to change back to English.
Press and hold the RESET button to change
back to English.
SETUP

RESET FOR SYSTEM
CHECK

press the RESET button

XXX% OIL LIFE
DOOR STATUS
BRAKE SYSTEM
FUEL LEVEL LOW
TBC GAIN = XX.X or NO
TRAILER
TBC GAIN = XX.X or
OUTPUT = //////
MYKEY DISTANCE
MYKEY(S) PROGRAMMED
ADMIN KEYS
PROGRAMMED

OIL LIFE XXX%

HOLD RESET=NEW

UNITS

press the RESET button

English or Metric

AUTOLAMP (SEC)

0 to 180 seconds

AUTOLOCK

ON or OFF

AUTOUNLOCK

ON or OFF

COURTESY WIPE

ON or OFF

EASY ENTRY EXIT

ON or OFF

REAR PARK AID

ON or OFF

TRAILER SWAY

ON or OFF

CREATE MYKEY, MYKEY SETUP or CLEAR MYKEY
RESET FOR REMOTE
START

press the RESET button

5, 10, 15 minutes

F150 (TF6) , enUSA

ON or OFF

Information Displays
SETUP

Climate On or Off
Quiet On or Off
LANGUAGE = ENGLISH,
SPANISH or FRENCH

English, Spanish or French

PRESS RESET FOR SYSTEM CHECK

AUTOLAMP (SEC)

The information display will begin to cycle
through the vehicle systems and provide
a status of the item if needed.

This feature keeps your headlights on for
up to three minutes after the ignition is
switched off.

Note: Some systems show a message only
if a condition is present

AUTOLOCK
This feature automatically locks all vehicle
doors when the vehicle is shifted into any
gear, putting the vehicle in motion.

OIL LIFE XXX%
Displays the remaining oil life. An oil
change is required whenever indicated by
the information display and according to
the recommended maintenance schedule.
USE ONLY RECOMMENDED ENGINE OILS.

AUTOUNLOCK
This feature automatically unlocks all
vehicle doors when the driver’s door is
opened within 10 minutes of the ignition
being turned off.

To reset the oil monitoring system to 100%
after each oil change, perform the
following:

COURTESY WIPE

Press and release the SETUP button
to display OIL LIFE XXX% HOLD RESET
= NEW.
2. Press and hold the RESET button for
two seconds and release to reset the
oil life to 100%.
Note: To change oil life 100% value (if
equipped with this feature) to another value,
proceed to Step 3.

This feature allows for an extra swipe of
the wipers after a wipe/wash cycle.
EASY ENTRY EXIT
This feature automatically moves the
driver’s seat rearward and adjusts the
steering wheel for easy exit/entry from the
vehicle.
REAR PARK AID (if equipped):

3. Once OIL LIFE SET TO XXX% is
displayed, release and press the RESET
button to change the Oil Life Start
Value. Each release and press will
reduce the value by 10%.

This feature sounds a warning tone to warn
the driver of obstacles near the rear
bumper, and functions only when R
(Reverse) gear is selected.

UNITS

TRAILER SWAY (if equipped)

Displays the current units English or Metric

This feature uses the electronic stability
control to mitigate trailer sway.

F150 (TF6) , enUSA

Information Displays
CREATE MYKEY, MYKEY SETUP or
CLEAR MYKEY

•

Press the up and down arrow buttons
to scroll through and highlight the
options within a menu.
Press the right arrow button to enter a
sub-menu.
Press the left arrow button to exit a
menu.
Press the OK button to choose and
confirm a setting or messages.

For more information, See Creating a
MyKey (page 53).

•

RESET FOR REMOTE START (if
equipped)

•

LANGUAGE = ENGLISH, SPANISH or
FRENCH

•

Allows you to choose which language the
message center will display in.

Main menu
You can access the menus using the
information display control.

Waiting four seconds or pressing the
RESET button cycles the message center
through each of the language choices.

Gauge Mode

Press the RESET button to set the
language choice.

E163179

Trip A / B

Information Display Controls
(Type 2) (If Equipped)

E138660

Fuel Economy
E163180

Truck Apps (If Equipped)
E163181

Settings
E144641

Information
E144642

Gauge Mode

E163179

E166921

F150 (TF6) , enUSA

Use the arrow buttons to choose
between the following gauge
options.

Information Displays

Gauge Mode

Gauge Detail

Trans Temp
Compass

The compass orientation
can be changed between
fixed north or rotating north.
To change the modes, press
OK when the compass
display is shown. Use the
right arrow to choose the
mode. Press and hold OK to
set the mode.

2–speed Auto 4X4

Displays power distribution
between the front and rear
wheels. More power to
either front or rear wheels
will be displayed by more
area filled in.

Blank
Trip A / B

E138660

Use the arrow buttons to choose
between the following trip
options.
Trip A / B

Trip time
Trip distance
Gal used
Avg mpg (L/100km)
Odometer (displays in lower line and may display in other menus)
Trip time

Press OK to pause the Trip A or B screen,
press again to un-pause.

Registers the time of individual journeys.

Press and hold OK to reset the currently
displayed trip information.

Trip distance
Registers the mileage of individual
journeys.
92

F150 (TF6) , enUSA

Information Displays
Gal used

Fuel Economy

Shows the amount of fuel used for a given
trip.
E163180

Avg MPG

Use the arrow buttons to choose
the desired fuel economy
display.

Shows the average distance traveled per
unit of fuel used for a given trip.
Fuel Economy

Fuel Econ.

Instant MPG (L/100km)
mi (km) to E
AVG MPG (L/100km)

Fuel Hist.

Options

5, 10, 30 Minutes or Last 5 Resets
Fuel Hist.

Hold OK to Reset, this resets the currently
displayed fuel economy information.

Shows your instantaneous fuel usage.

Shows fuel usage as a bar graph based on
time. The graph is updated each minute
with the fuel economy that was achieved
during the prior 5, 10, 30 minutes of driving.

mi to E

Truck Apps

Shows the approximate distance your
vehicle can travel before running out of
fuel.

In this mode, off-road
information depicted with
E163181
graphics and trailer towing
application options are available.

Instant MPG

Average MPG

Note: Some items are optional and may
not appear.

Shows the average fuel usage based on
time. Press and hold OK to reset this value.

Truck Apps

Off Road

AdvanceTrac® mode, hill descent control, off-road mode, off-road camera:
Displays which modes are active. (SVT Raptor)
Pitch and bank angle (in degrees)
Steering angle (in degrees)
Differential lock/unlock
Torque flow
Press OK for Info

4X4 System

F150 (TF6) , enUSA

Information Displays
Truck Apps

AdvanceTrac®
2–speed Auto 4X4
ELD (Electronic Locking Differential)
Hill Descent Control

Truck Apps (cont’d)

Off Road
(cont’d)

Press OK for Info

Trailer

Trailer Disconnected

Off-Road Mode

Off-Road Camera (SVT Press OK to Enable / Disable
Raptor)

Active trailer name or default trailer
Accumulated trailer distance
Trailer gain and output
Press OK for options

Change Active Trailer
Connection Checklist (if Conventional, Fifth
equipped)
Wheel or Gooseneck.
Delete Trailer
Information Screen

Tow Haul mode or
Trailer Brake Controller

Rename Trailer
Reset Trailer Mileage / Kilometers (if equipped)
Pitch and bank angle (in degrees)

Differential lock/unlock

Displays the pitch angle (front to rear) and
bank angle (side to side) of the road
surface.

Displays the state (locked or unlocked) of
the electronic locking differential.

Steering angle (in degrees)

Displays the torque flow to the front and
rear driveline and operating mode of the
transfer case: 4X2, 4X4 High, 4X4 Low, 4X4
Auto.

Torque flow

Displays the steering angle of the front
wheels after the vehicle has been driven
for a period of time.

F150 (TF6) , enUSA

Information Displays
Trailer disconnected

Connection Checklist

Disregard this status if your vehicle is not
equipped with a factory installed trailer
brake controller. This message may appear
when an aftermarket TBC is used even
when the trailer is connected.

Use the up/down arrows to highlight one
of these choices and press OK to display
the connection checklist. Follow the
on-screen instructions to go through the
connections list.

Change Active Trailer

Delete Trailer

When this is highlighted, press the right
arrow key to change the currently selected
trailer. Use the up and down arrows to
select a trailer and press the OK button to
choose the highlighted trailer.

Use the up/down arrows to highlight the
trailer you want to delete and press OK to
delete. Follow the on-screen prompts to
exit or confirm delete.
Rename Trailer

Adding a new trailer

Use the up/down buttons to highlight a
trailer and press OK to select it. Use the
up/down arrow buttons to change the
characters as needed. When done, press
OK to accept the change.

Use the up/down arrows to highlight New
Trailer and press the right arrow key to
enter the New Trailer input screen. Use the
up/down arrow keys to choose alpha,
numeric and symbol characters and then
press the right arrow to move the character
space over. Continue adding characters as
needed. Press the left arrow to go back
and change a previously selected
character. When finished with the new
trailer name, press OK to accept the new
trailer name.

Reset Trailer Mileage / Kilometers
Use the up/down buttons to select a
trailer, then press and hold OK to reset the
trailer mileage (kilometers).
Settings

E144641

Use the arrow buttons to
configure different driver setting
choices.

Note: Some items are optional and may
not appear.
Settings

Driver
Assist

Rear Park Aid

On or Off

Rear Video Camera

Camera Delay

On or Off

Visual Park Aid

On or Off

Guidelines

Fixed or Off

Zoom Levels

On or Off

Trailer Brake Mode

Electric or Elect. Over Hydraulic

Trailer Sway Control

On or Off

F150 (TF6) , enUSA

Information Displays
Settings

Vehicle

Autolamp Delay

Off or XXX seconds

DTE Calculation
(distance to empty)

Normal history used

Easy Entry/Exit

On or Off

Locks

Autolock

On or Off

Autounlock

On or Off

Unlocking

One Stage or Two
Stage

Towing history used

Menu Control

Standard or Memory On

Oil Life Reset

Set to XXX% (Hold OK to Reset)

Pwr Running Boards

Auto, Off or Out

Settings (cont’d)

Vehicle Remote Start
(cont’d)

Climate Control

Front Defrost

Auto/Off

Rear Defrost
Driver Seat
Passenger Seat
Heater-A/C

Wiper Control

Duration

5, 10, 15 minutes or Off

Quiet Start

On or Off

Courtesy Wipe

On or Off

Rain Sensing
Wipers

On or Off

F150 (TF6) , enUSA

Auto or Last
Setting

Information Displays

Settings (cont’d)

MyKey

Create MyKey

Hold OK to create MyKey

AdvanceTrac

Always On or Selectable

MAX Speed

80 MPH (130 km/h) or Off

Speed Warning

45, 55 or 65 MPH (75, 90 or 105 km/h), Off

Volume Limiter

On or Off

Clear MyKey

Hold OK to Clear MyKey

Language

English, Español, Français (Hold OK to Set)

Units

Distance

Miles & Gallons
L/100km
km/L

Temperature

Celsius (°C)
Fahrenheit (°F)

Information
In this mode, you can view
different vehicle system
information and perform a
system check.
E144642

Information

MyKey

MyKeys (Number of MyKeys programmed)
Admin Keys (Number of admin keys)
MyKey Miles (km) (Distance traveled using a programmed
MyKey)

System Check

Some items will only display during a system check if a
problem has been detected. If an issue exists on one of
the monitored systems, the number of warnings that need
immediate attention will display in red and the number of
informational warnings will display in amber. Use the up/
down arrow buttons to scroll through the list; press the
right arrow button to display specific information on the
highlighted warning

F150 (TF6) , enUSA

Information Displays
Transmission indicator display (if
equipped)

INFORMATION MESSAGES

The transmission gear indicator displays
in the right side of the information display
when using the SelectShift Automatic™
transmission feature. These displays will
not be shown in all screen modes. For
example: when programming certain
vehicle features or in certain information
menus.

Note: Depending on the vehicle options
equipped with your vehicle, not all of the
messages will display or be available.
Certain messages may be abbreviated or
shortened depending upon which cluster
type you have.
Press the RESET button for Type 1 displays
or the OK button for Type 2 displays to
acknowledge and remove some messages
from the information display. Other
messages will be removed automatically
after a short time.
Certain messages need to be confirmed
before you can access the menus.

AdvanceTrac® and Traction Control
Message

Action

SERVICE ADVANCETRAC

Displays when the system detects a condition that requires
service. Contact your authorized dealer as soon as possible.

ADVANCETRAC OFF

Displayed when the AdvanceTrac® system has been disabled
by the driver.

ADVANCETRAC ON

Displayed when the AdvanceTrac® system has been enabled
by the driver.

ADVANCETRAC SPORT
MODE

Displayed when the AdvanceTrac® sport mode has been
enabled by the driver. (SVT Raptor)

TRACTION CONTROL
OFF

Displayed when the traction control has been disabled by the
driver. See Using Traction Control (page 166).

TRACTION CONTROL
ON

Displayed when the traction control has been enabled by the
driver. See Using Traction Control (page 166).

Airbag
Message

Action

REMOVE OBJECTS
NEAR PASSENGER
SEAT

Displays when the system detects a malfunction due to a
blocked sensor.

F150 (TF6) , enUSA

Information Displays
Alarm and Security
Message

Action

TO STOP ALARM
START VEHICLE

Displays when the alarm has been triggered due to unauthorized entry. See Anti-Theft Alarm (page 62).

SECURITY SYSTEM
FAULT

Displays when the security system has detected a fault. See
your authorized dealer for service.

Battery and Charging System
Message

Action

TURN POWER OFF TO
SAVE BATTERY

Displayed when the battery management system determines
that the battery is at a low state of charge or, the ignition has
been in accessory position or on position with the engine off
for approximately 45 minutes. Turn the ignition off as soon
as possible to protect the battery. This message will clear
once the vehicle has been started and the battery state of
charge has recovered. Turning off unnecessary electrical loads
while driving will allow faster battery state-of-charge recovery.
See Changing the 12V Battery (page 246).

LOW BATTERY
FEATURES TEMPORARILY TURNED OFF

Displayed when the battery management system detects an
extended low-voltage condition. Various vehicle features will
be disabled to help preserve the battery. Turn off as many of
the electrical loads as soon as possible to improve system
voltage. If the system voltage has recovered, the disabled
features will operate again as normal.

Doors and Locks
Message

Action

X DOOR AJAR

Displays when the door(s) listed is not completely closed.

F150 (TF6) , enUSA

Information Displays
Drivetrain
Message

Action

LOCKING DIFFERENTIAL
ENGAGED/DISENGAGED

Displayed when the electronic locking differential (ELD) is
enabled or disabled.

TO ENGAGE LOCKING
DIFFERENTIAL SLOW
TO XX MPH/KM/H

Displays when the electronic locking differential requests a
certain speed requirement to engage.

TO ENGAGE LOCKING Displays when the electronic locking differential request the
DIFFERENTIAL RELEASE
accelerator to be released in order to engage.
ACCELERATOR PEDAL
CHECK LOCKING
DIFFERENTIAL

Displayed when an electronic locking differential (ELD) system
fault is present. See Using Four-Wheel Drive (page 153).

SHIFT TO PARK

Displays as a reminder to shift into park.

NEUTRAL TOW
ENABLED LEAVE
TRANSMISSION IN
NEUTRAL

Displayed when the transfer case is in the neutral position.
This message indicates that the vehicle is safe to be towed
with all four wheels on the ground.

NEUTRAL TOW
DISABLED

Displayed when the transfer case is NOT in the neutral position. This message indicates that the vehicle is NOT safe to
be towed with all four wheels on the ground.

Engine
Message

Action

POWER REDUCED TO LOWER Displays when the engine temperature gauge needle
ENGINE TEMP
moves to H. See Engine Coolant Check (page 241).

Fuel
Message

Action

FUEL LEVEL LOW

Displays as an early reminder of a low fuel condition.

CHECK FUEL FILL INLET

Displays when the fuel fill inlet may not be properly closed.

100

F150 (TF6) , enUSA

Information Displays
Key
Message

Action

COULD NOT PROGRAM
INTEGRATED KEY

Displays when an attempt is made to program a fifth integrated key. See Replacing a Lost Key or Remote Control
(page 52).

TO DRIVE: TURN KEY
TO ON

Displays when the factory equipped remote start is activated.

Maintenance
Message

Action

ENGINE OIL CHANGE SOON

Displays when the engine oil life is nearing its end. See
Engine Oil Check (page 240).

OIL CHANGE REQUIRED

Displayed when the oil life left reaches 0%. See
Engine Oil Check (page 240).

BRAKE FLUID LEVEL LOW

Indicates the brake fluid level is low and the brake
system should be inspected immediately. See Brake
Fluid Check (page 246).

CHECK BRAKE SYSTEM

Displays when the brake system needs servicing. If the
warning stays on or continues to come on, contact
your authorized dealer as soon as possible.

SERVICE POWER STEERING

The power steering system has detected a condition
that requires service. See your authorized dealer

SERVICE POWER STEERING
NOW

The power steering system has detected a condition
within the power steering system that requires service
immediately. See your authorized dealer.

POWER STEERING ASSIST
FAULT

The power steering system has disabled power
steering assist due to a system error. See your authorized dealer.

101

F150 (TF6) , enUSA

Information Displays
MyKey®
Message

Action

MYKEY ACTIVE DRIVE SAFELY

Displays when MyKey is active.

ADVANCETRAC ALWAYS ON MYKEY SETTING

Displays when a MyKey is in use and the ESC cannot
be deactivated.

VEHICLE NEAR TOP SPEED

Displays when a MyKey is in use and the MyKey speed
limit is on and the vehicle speed is approaching 80
mph (130 km/h).

VEHICLE AT TOP SPEED MYKEY SETTING

Displays when a MyKey is in use and the MyKey speed
limit is on and the vehicle speed is 80 mph (130 km/
h).

SPEED LIMITED TO 80 MPH

Displays when starting the vehicle and MyKey is in use
and the MyKey speed limit is on.

SPEED LIMITED TO 130 KM/H

Displays when starting the vehicle and MyKey is in use
and the MyKey speed limit is on

CHECK SPEED DRIVE SAFELY

Displayed when a MyKey is in use and the optional
setting is on and the vehicle exceeds a preselected
speed.

BUCKLE UP TO UNMUTE
AUDIO

Displayed when a MyKey is in use and Belt-Minder® is
activated.

MYKEY COULD NOT PROGRAM

Displayed when an attempt is made to program a
spare key using two existing MyKeys.

Park Aid
Message

Action

CHECK REAR PARK AID

Displays when the transmission is in R (Reverse) and
the park aid is disabled.

REAR PARK AID OFF

Displays when the rear park aid is disabled by the
driver.

REAR PARK AID ON

Displays when the rear park aid is enabled.

102

F150 (TF6) , enUSA

Information Displays
Park Brake
Message

Action

PARK BRAKE ENGAGED

Displays when the parking brake is set and the vehicle is in
motion.

Off Road
Message

Action

FOR OFF ROAD SLOW TO 5
MPH

Displayed when the vehicle speed requirement for offroad mode entry has not been met.

OFF ROAD MODE ENABLED

Displayed when off-road mode becomes active.

EXITING OFF ROAD MODE

Displayed when off-road mode becomes inactive.

HILL DESCENT CONTROL
ACTIVE

Displayed when hill descent control mode becomes
active.

HILL DESCENT CONTROL OFF

Displays when hill descent control mode becomes
inactive.

FOR HILL DESCENT REDUCE
SPEED

Displays when the vehicle speed requirement for offroad mode entry has not been met.

FOR HILL DESCENT SELECT
GEAR

Displays when the driver is able to select a transmission gear for hill descent mode.

HILL DESCENT - DRIVER
RESUME CONTROL

Displays when hill descent control mode is deactivated
and the driver must resume control.

HILL DESCENT CONTROL
FAULT

Displays when a hill descent system fault is present.

HILL DESCENT CONTROL OFF
SYSTEM COOLING

Displays when the hill descent system is cooling due
to overuse.

HILL DESCENT CONTROL
READY

Displays when the hill descent control switch is turned
on.

CAMERA MALFUNCTION

Displayed when the front camera is not operating
properly.

103

F150 (TF6) , enUSA

Information Displays
Tire Pressure Monitoring System
Message

Action

LOW TIRE PRESSURE

Displays when one or more tires on your vehicle have low tire
pressure. See Tire Pressure Monitoring System (page 283).

TIRE PRESSURE
MONITOR FAULT

Displays when the tire pressure monitoring system is
malfunctioning. If the warning stays on or continues to come
on, contact your authorized dealer. See Tire Pressure
Monitoring System (page 283).

TIRE PRESSURE
SENSOR FAULT

Displayed when a tire pressure sensor is malfunctioning, or
your spare tire is in use. For more information on how the
system operates under these conditions, see See Tire Pressure Monitoring System (page 283). If the warning stays on
or continues to come on, contact your authorized dealer as
soon as possible.

Trailer
Message

Action

TRAILER BRAKE GAIN: XX.X
[OUTPUT]

Displays the current gain setting for the trailer brake.

TRAILER BRAKE GAIN: XX.X NO
TRAILER

Displays the current gain setting for the trailer brake
when a trailer is not connected.

TRAILER BRAKE MODULE
FAULT

Displayed and accompanied by a single chime, in
response to faults sensed by the TBC. See Trailer
Sway Control (page 192).

TRAILER CONNECTED

Displays when a correct trailer connection (a trailer
with electric trailer brakes) is sensed during a given
ignition cycle.

104

F150 (TF6) , enUSA

Information Displays
Message

Action

TRAILER DISCONNECTED

Displays when a trailer connection becomes disconnected, either intentionally or unintentionally, and has
been sensed during a given ignition cycle. Disregard
this status if your vehicle is not equipped with a factory
installed trailer brake controller. This message may
appear when an aftermarket TBC is used even when
the trailer is connected.

TRAILER SWAY REDUCE
SPEED

Displays when the trailer sway control has detected
trailer sway.

WIRING FAULT ON TRAILER

Displays if there are certain faults in the vehicle wiring
and trailer wiring/brake system. See Towing a Trailer
(page 191).

4WD
Message

Action

CHECK 4X4

Displays when a 4X4 system fault is present. See
Using Four-Wheel Drive (page 153).

4X4 SHIFT IN PROGRESS

Displays when the 4X4 system is making a shift.

FOR 4X4 LOW APPLY BRAKE

Displays when trying to select 4X4 LOW.

FOR 4X4 LOW SHIFT TO N

Displays when 4X4 LOW is selected and the vehicle is
stopped.

FOR 4X4 LOW SLOW TO 3 MPH Displays when 4X4 LOW is selected while the vehicle
is moving.
TO EXIT 4X4 LOW APPLY
BRAKE

Displays when 2WD is selected from 4X4 LOW mode.

TO EXIT 4X4 LOW SHIFT TO N

Displays when 2WD is selected while the vehicle has
been stopped in 4X4 LOW.

TO EXIT 4X4 LOW SLOW TO 3
MPH

Displays when 2WD is selected while the vehicle is
operating in 4X4 LOW.

SHIFT DELAYED PULL
FORWARD

May display when shifting to or from 4X4 LOW.

105

F150 (TF6) , enUSA

Climate Control
MANUAL CLIMATE CONTROL

E167066

Defrost: Press the button to distribute air to the windshield vents and de-mister.
Air distribution to instrument panel and footwell vents turn off. You can use
this setting to defog and clear the windshield of a thin covering of ice.

Rear defrost and heated mirrors: Turns the heated mirrors on and off as well
as the heated rear window, if your vehicle has that feature. See Heated
Windows and Mirrors (page 112).

Air distribution control: Press these buttons to turn airflow from the
windshield, instrument panel, or footwell vents on or off. The system can
distribute air through any combination of these vents.

A/C: Press the button to turn air conditioning compressor on or off. Use air
conditioning with recirculated air to improve cooling performance and efficiency.
Note: In certain conditions, the air conditioning compressor may continue to
operate even after you switch off the air conditioning with the A/C button.

MAX A/C: Press the button to maximize cooling. Recirculated air flows through
the instrument panel vents, air conditioning automatically turns on and the fan
automatically adjusts to the highest speed.

106

F150 (TF6) , enUSA

Climate Control
G

Temperature control: Controls the temperature of the airflow in your vehicle.
Adjust to select the desired temperature.

Fan speed control: Controls the volume of air circulated in your vehicle. Adjust
to select the desired fan speed.

Power: Press the button to turn the system on and off. Switching off the climate
control system prevents outside air from entering the vehicle.

MANUAL CLIMATE CONTROL

E167068

Fan speed control: Controls the volume of air circulated in your vehicle. Adjust
to select the desired fan speed.

Rear defrost and heated mirrors: Turns the heated mirrors on and off as well
as the heated rear window, if your vehicle has that feature. See Heated
Windows and Mirrors (page 112).

Air distribution control: Press these buttons to turn airflow from the
windshield, instrument panel, or footwell vents on or off. The system can
distribute air through any combination of these vents.

A/C: Press the button to turn air conditioning compressor on or off. Use air
conditioning with recirculated air to improve cooling performance and efficiency.

107

F150 (TF6) , enUSA

Climate Control
Note: In certain conditions, the air conditioning compressor may continue to
operate even after you switch off the air conditioning with the A/C button.
F

Recirculated air: Press the button to switch between outside air and
recirculated air. When recirculated air is selected, the air currently in the
passenger compartment recirculates. This may reduce the time needed to cool
the interior (when used with A/C) and may also reduce unwanted odors from
entering your vehicle. Even when you do not select this button, air may still
recirculate in some instances in order to reduce vehicle warm-up time in cold
conditions or to cool down time in hot conditions.
Note: Recirculated air engages automatically when you select MAX A/C, or
turn on manually in any airflow mode except defrost.
Note: You may notice changes in sound between recirculated mode and other
airflow modes.
Note: For better cooling in hot conditions, recirculated air automatically engages
when the air distribution control is in panel or panel and floor modes and the
air conditioning is on. You can switch to fresh air by pressing the recirculated
air button again.

Temperature control: Controls the temperature of the airflow in your vehicle.
Adjust to select the desired temperature.

Power: Press the button to turn the system on and off. Switching off the climate
control system prevents outside air from entering the vehicle.

108

F150 (TF6) , enUSA

Climate Control
AUTOMATIC CLIMATE CONTROL (IF EQUIPPED)

D E

E163164

Power and Driver temperature control: Press the button to turn the system
on and off. Switching off the climate control system prevents outside air from
entering the vehicle. Turn to increase or decrease the air temperature for the
driver side of the vehicle. This control also adjusts the passenger side
temperature when not in dual zone mode.

Heated rear window: Turns the heated rear window on and off.

Air distribution control: Press these buttons to turn airflow from the
windshield, instrument panel, or footwell vents on or off. The system can
distribute air through any combination of these vents.

MAX A/C: Press the button to maximize cooling. Recirculated air flows through
the instrument panel vents, air conditioning automatically turns on, and the fan
automatically adjusts to the highest speed.

109

F150 (TF6) , enUSA

Climate Control
G

Recirculated air: Press the button to switch between outside air and
recirculated air. When you select recirculated air, the air currently in the
passenger compartment recirculates. This may reduce the time needed to cool
the interior (when used with A/C) and may reduce unwanted odors from
entering your vehicle.
Note: Recirculated air may turn off automatically (or be prevented from turning
on) in all airflow modes except MAX A/C to reduce risk of fogging. Recirculated
air may also turn on and off automatically in Panel or Panel and Floor airflow
modes during hot weather in order to improve cooling efficiency.

PASS TEMP: Turn to increase or decrease the air temperature on the passenger
side of the vehicle. This turns on dual zone mode.

Fan speed control +: Press to increase the volume of air circulated in your
vehicle.

AUTO: Press the button to turn on automatic operation. Select the desired
temperature using the temperature control. The system adjusts fan speed, air
distribution, air conditioning operation, and selects outside air or recirculated
air to heat or cool the vehicle in order to maintain the desired temperature. You
can also use the AUTO button to turn off dual zone operation by pressing and
holding the button for more than two seconds.

Fan speed control -: Press to decrease the volume of air circulated in your
vehicle.

HINTS ON CONTROLLING THE
INTERIOR CLIMATE

Note: To improve the time to reach comfort
in hot weather, drive with the windows
slightly open for 2-3 minutes after start-up
or until your vehicle airs out.

General Hints

Manual Climate Control

Note: Prolonged use of recirculated air may
cause the windows to fog up.

Note: To reduce fogging of the windshield
during humid weather, adjust the air
distribution control to the windshield air
vents position.

Note: You may feel a small amount of air
from the footwell air vents regardless of the
air distribution setting.

Automatic Climate Control

Note: To reduce humidity build-up inside
your vehicle, do not drive with the system
switched off or with recirculated air always
switched on.

Note: Adjusting the settings when your
vehicle interior is extremely hot or cold is
not necessary. The system automatically
adjusts to heat or cool the cabin to your
selected temperature as quickly as possible.
For the system to function efficiently, the
instrument panel and side air vents should
be fully open.

Note: Do not place objects under the front
seats as this may interfere with the airflow
to the rear seats.
Note: Remove any snow, ice or leaves from
the air intake area at the base of the
windshield.
110

F150 (TF6) , enUSA

Climate Control
Note: If you select AUTO during cold
outside temperatures, the system directs
airflow to the windshield and side window
vents. In addition, the fan may run at a
slower speed until the engine warms up.

Note: If you select AUTO during hot outside
temperatures, or when the inside of the
vehicle is hot, the system automatically uses
recirculated air to maximize interior cooling.
When the interior reaches the selected
temperature, the system automatically
switches to using outside air.

Heating the Interior Quickly
Vehicle with manual climate control

Vehicle with automatic climate control

Adjust the fan speed to the highest
speed setting.

Press the AUTO button.

Adjust the temperature control to the
highest setting.

Adjust the temperature control to the
desired setting.

Select the footwell air vents using the
air distribution buttons.

Recommended Settings for Heating
Vehicle with manual climate control

Vehicle with automatic climate control

Adjust the fan speed to the center
setting.

Press the AUTO button.

Adjust the temperature control to the
midway point of the hot settings.

Adjust the temperature control to the
desired setting. Use 72°F (22°C) as a
starting point, then adjust the setting as
necessary.

Select the footwell air vents using the
air distribution buttons.

Cooling the Interior Quickly
Vehicle with manual climate control

Press the MAX A/C button.

Drive with the windows open for 2-3
minutes.

Press the MAX A/C button.

111

F150 (TF6) , enUSA

Vehicle with automatic climate control

Climate Control
Recommended Settings for Cooling
Vehicle with manual climate control

Vehicle with automatic climate control

Adjust the fan speed to the center
setting.

Press the AUTO button.

Adjust the temperature control to the
midway point of the cold settings.

Adjust the temperature control to the
desired setting. Use 72°F (22°C) as a
starting point, then adjust the setting as
necessary.

Select the instrument panel air vents
using the air distribution buttons.

Side Window Defogging in Cold Weather
Vehicle With Manual Climate Control

Vehicle With Automatic Climate Control

Select the instrument panel and footwell Press the defrost button.
air vents positions through the air distribution control.

Press the A/C button.

Adjust the temperature control to the
desired setting.

Adjust the fan speed to the highest
setting.

Direct the instrument panel side air vents
toward the side windows.

Close the instrument panel center vents.

Adjust the temperature control to the
desired setting. Use 72°F (22°C) as a
starting point, then adjust the setting as
necessary.

Note: If your vehicle is equipped with a
sliding rear window, the feature does not
operate when you open the window.

HEATED WINDOWS AND
MIRRORS

Press the button to clear the rear window
of thin ice and fog. Press the button again
within 10 minutes to switch it off. It
switches off automatically after 10
minutes, or when you switch the ignition
off.

Heated Rear Window (If Equipped)
Note: The engine must be running to use
this feature.

112

F150 (TF6) , enUSA

Climate Control
You can adjust the default remote start
settings using the information display
controls. See Information Displays
(page 87).

Do not use razor blades or other sharp
objects to clean the inside of the rear
window or to remove decals from the
inside of the rear window. This may
cause damage to the heated grid lines.
Your warranty does not cover this
damage.

Automatic Settings
In hot weather, the system is set to 72°F
(22°C). The cooled seats are set to high
(if available, and selected to AUTO in the
information display).

Heated Exterior Mirror (If Equipped)
Note: Do not remove ice from the mirrors
with a scraper or attempt to readjust the
mirror glass that has frozen in place. These
actions could cause damage to the glass
and mirrors.

In moderate weather, the system either
heats or cools (based on previous
settings). The rear defroster, heated
mirrors and heated seats do not
automatically switch on.

Note: Do not clean the housing or glass of
any mirror with harsh abrasives, fuel or other
petroleum-based cleaning products.

In cold weather, the system is set to 72°F
(22°C). The heated seats are set to high
(if available, and selected to AUTO in the
information display). The rear defroster
and heated mirrors automatically switch
on.

The heated mirrors remove ice, mist and
fog when you switch on the heated rear
window.

REMOTE START (IF EQUIPPED)
The remote start feature allows you to
pre-condition the interior of your vehicle.
The climate control system works to
achieve comfort according to your previous
settings.
Note: You cannot adjust the system during
remote start operation.
Turn the ignition on to return the system
to its previous settings. You can now make
adjustments normally, but you need to turn
certain vehicle-dependent features back
on, such as:
• Heated seats.
• Cooled seats.
• Heated steering wheel.
• Heated mirrors.
• Heated rear window.

113

F150 (TF6) , enUSA

Seats
We recommend that you follow these
guidelines:
• Sit in an upright position with the base
of your spine as far back as possible.
• Do not recline the seat back more than
30 degrees.
• Adjust the head restraint so that the
top of it is level with the top of your
head and as far forward as possible.
Make sure that you remain
comfortable.
• Keep sufficient distance between
yourself and the steering wheel. We
recommend a minimum of 10 inches
(25 centimeters) between your
breastbone and the air bag cover.
• Hold the steering wheel with your arms
slightly bent.
• Bend your legs slightly so that you can
press the pedals fully.
• Position the shoulder strap of the
safety belt over the center of your
shoulder and position the lap strap
tightly across your hips.

SITTING IN THE CORRECT
POSITION
WARNINGS
Sitting improperly, out of position or
with the seat back reclined too far
can take weight off the seat cushion
and affect the decision of the passenger
sensing system, resulting in serious injury
or death in the event of a crash. Always sit
upright against your seat back, with your
feet on the floor.
Do not recline the seat back as this
can cause the occupant to slide
under the safety belt, resulting in
serious injury in the event of a crash.
Do not place objects higher than the
seat back to reduce the risk of
serious injury in the event of a crash
or during heavy braking.

Make sure that your driving position is
comfortable and that you can maintain full
control of your vehicle.

HEAD RESTRAINTS
WARNINGS
Fully adjust the head restraint before
you sit in or operate your vehicle. This
will help minimize the risk of neck
injury in the event of a crash. Do not adjust
the head restraint when your vehicle is
moving.

E68595

When you use them properly, the seat,
head restraint, safety belt and air bags will
provide optimum protection in the event
of a crash.

The head restraint is a safety device.
Whenever possible it should be
installed and properly adjusted when
the seat is occupied. An improperly
adjusted head restraint may not
adequately protect an occupant during an
impact from the rear.
114

F150 (TF6) , enUSA

Seats
Rear Seat Center Head Restraint

WARNINGS
Install the head restraint properly to
help minimize the risk of neck injury
in the event of a crash.

Note: Adjust the seatback to an upright
driving position before adjusting the head
restraint. Adjust the head restraint so that
the top of it is level with the top of your head
and as far forward as possible. Make sure
that you remain comfortable. If you are
extremely tall, adjust the head restraint to
its highest position.

E166701

The head restraints consist of:

Front Seat Head Restraint

An energy absorbing head
restraint.

Two steel stems.

Guide sleeve adjust and release
button.

Guide sleeve unlock and remove
button.

Fold button (rear seat outboard
only).

E138642

Adjusting the Head Restraint

Rear Seat Outboard Head Restraints

Raising the Head Restraint

Pull the head restraint up.
Lowering the Head Restraint

1. Press and hold button C.
2. Push the head restraint down.

Removing the Head Restraint
E166700

Pull up the head restraint until it
reaches the highest adjustment
position.
2. Press and hold buttons C and D.
3. Pull up the head restraint.

Note: For rear seat outboard seats, you can
fold the head restraint forward for easier
removal.
115

F150 (TF6) , enUSA

Seats
Installing the Head Restraint

Installing the Head Restraint

Align the steel stems into the guide sleeves
and push the head restraint down until it
locks.

Folding the Head Restraint

Tilting Head Restraints (If Equipped)

Note: The rear seat outboard head
restraints may fold forward for improved
visibility.

The front head restraints may have a tilting
feature for extra comfort. To tilt the head
restraint, do the following:

1. Press and hold button E.
2. Pull it back up to reset.
Front Seat Center Head Restraint
Your vehicle may be equipped with a front
row center head restraint that is
non-adjustable. This head restraint
consists of:

E144727

Adjust the seatback to an upright
driving or riding position.
2. Pivot the head restraint forward toward
your head to the desired position.
E162872

An energy absorbing head
restraint.

Two steel stems.

Guide sleeve unlock and remove
button.

After the head restraint reaches the
forward-most tilt position, pivot it forward
again to release it to the rearward, un-tilted
position.
Note: Do not attempt to force the head
restraint backward after it is tilted. Instead,
continue tilting it forward until the head
restraint releases to the upright position.

Removing the Head Restraint

MANUAL SEATS

Pull up the head restraint until it
reaches the highest adjustment
position.
2. Press and hold buttons C.
3. Pull up the head restraint.

WARNING
Do not adjust the driver's seat or
seatback when your vehicle is
moving.

116

F150 (TF6) , enUSA

Seats
Moving the Seat Backward and
Forward

POWER SEATS (IF EQUIPPED)
WARNINGS
Do not adjust the driver's seat or
seatback when your vehicle is
moving. Adjusting your seatback
while the vehicle is in motion may cause
loss of control of the vehicle.
Do not place cargo or any objects
behind the seatback before returning
it to the original position.

E162727

Recline Adjustment

E162730

The control is located on the outboard side
of the seat. Move the switch in the direction
of the arrow to raise or lower the seat
cushion or to move the seat forward,
backward, up or down.

Power Recline (If Equipped)

E162728

Manual Lumbar

(If Equipped)

E162731

Move the switch to recline the seatback
forward or rearward.

E166702

The lumbar support control is located on
the outboard side of the seat. Turn the
control to adjust your support.

117

F150 (TF6) , enUSA

Seats
Power Lumbar (If Equipped)

2
E162734

Saving a Pre-Set Position

E164101

1. Switch the ignition on.
2. Move the memory features to the
desired positions using the associated
controls.
3. Press and hold button 1 for about two
seconds until you hear a single chime.

The control is located on the outboard side
of the seat. Press the forward or rearward
side of the control for more or less support.

MEMORY FUNCTION (IF EQUIPPED)

To program position 2, repeat the previous
procedure using button 2.

WARNINGS
Before activating the seat memory,
make sure that the area immediately
surrounding the seat is clear of
obstructions and that all occupants are
clear of moving parts.

Note: You can save a memory pre-set at
any time.
Recalling a Pre-Set Position:
Press and release the pre-set memory
button desired. The seat, mirrors, pedals
and steering column will move to the
position stored for that pre-set.

Do not use the memory function
when your vehicle is moving.
This feature will automatically recall the
position of the driver's seat, power mirrors,
optional adjustable pedals and optional
steering column.

Note: If the easy entry and exit feature is
enabled, any memory recall while the
ignition is off will move the seat and steering
column to the easy entry position.

The memory control is located on the
outboard side of the driver's seat.

You can recall a programmed memory
position:
• When the ignition is off.
• Or only if the transmission is in park (P),
neutral (N), or if the ignition is on.
You can program a remote entry
transmitter to recall a memory setting.
See Keys and Remote Controls (page
49).

118

F150 (TF6) , enUSA

Seats
2. Rotate the seat cushion up until it locks
into the vertical storage position.

You can also program a personal keyless
entry code to recall a memory setting. See
Locks (page 57).

Returning the Seat to the Seating
Position

Easy Entry and Exit Feature (If
Equipped)

WARNING

If you enable the easy entry and exit
feature, it automatically moves the driver's
seat rearward 2 inches (5 centimeters)
when the transmission selector lever is in
position P and you remove the key from
the ignition.

Make sure that cargo or any objects
are not trapped underneath the seat
cushion before returning the seat
cushion to its original position, and that the
seat cushion locks into place. Failure to do
so may prevent the seat from operating
properly in the event of a crash, which
could increase the risk of serious injury.

If the seat is located less than 2 inches (5
centimeters) from the rear of the seat
track, the seat travel will be less than 2
inches (5 centimeters) rearward.

Pull the control on the side of the seat
to release the seat cushion from the
storage position.
2. Push the seat cushion down until it
locks into the horizontal position.

The driver's seat will return to the previous
position when you put the key in the
ignition.
You can enable or disable this feature
through the information display. See
Information Displays (page 87).

Folding up the Rear Seat Cushion
(Super Crew)
The rear seat has a split 60/40 cushion.
You can flip each seat cushion up into a
vertical storage position.

REAR SEATS
Folding Up the Rear Seats (SuperCab)
The rear seat has a split 60/40 cushion.
You can flip each seat cushion up into a
vertical storage position.

E166703

Rotate the seat cushion up until it locks
into the vertical storage position.
E162737

Pull the control to release the seat
cushion.

119

F150 (TF6) , enUSA

Seats
Returning the Seat to the Seating
Position

HEATED SEATS (IF EQUIPPED)

WARNING

People who are unable to feel pain
to their skin because of advanced
age, chronic illness, diabetes, spinal
cord injury, medication, alcohol use,
exhaustion or other physical conditions,
must exercise care when using the heated
seat. The heated seat may cause burns
even at low temperatures, especially if
used for long periods of time. Do not place
anything on the seat that insulates against
heat, such as a blanket or cushion. This
may cause the heated seat to overheat.
Do not puncture the seat with pins, needles
or other pointed objects. This may damage
the heating element which may cause the
heated seat to overheat. An overheated
seat may cause serious personal injury.
Do not do the following:
• Place heavy objects on the seat.
• Operate the heated seat if water or any
other liquid is spilled on the seat. Allow
the seat to dry thoroughly.
• Operate the heated seats unless the
engine is running. Doing so can cause
the battery to lose charge.

E166704

Pull the control on the bottom of the
seat cushion to release the seat
cushion from the storage position.
2. Push the seat cushion down until it
locks into the horizontal position.

E146322

To operate the heated seats, press the
heated seat symbol to cycle through the
various heat settings and off. Warmer
settings are indicated by more indicator
lights.

120

F150 (TF6) , enUSA

Seats
Rear Heated Seats (If Equipped)
WARNING
People who are unable to feel pain
to the skin because of advanced age,
chronic illness, diabetes, spinal cord
injury, medication, alcohol use, exhaustion,
or other physical conditions, must exercise
care when using the seat heater. The seat
heater may cause burns even at low
temperatures, especially if used for long
periods of time. Do not place anything on
the seat that insulates against heat, such
as a blanket or cushion, because this may
cause the seat heater to overheat. Do not
puncture the seat with pins, needles, or
other pointed objects because this may
damage the heating element which may
cause the seat heater to overheat. An
overheated seat may cause serious
personal injury.

E166817

•
•

Press this symbol for minimum heat.
Press again to turn off.

The heated seat module resets at every
ignition run cycle. While the ignition is in
the on position, press the high or low
heated seat switch to enable heating
mode. When activated, they will turn off
automatically when the engine is turned
off.
The indicator light will illuminate when the
heated seats have been activated.

Do not do the following:
• Place heavy objects on the seat.
• Operate the seat heater if water or any
other liquid is spilled on the seat. Allow
the seat to dry thoroughly.

VENTILATED SEATS (IF EQUIPPED)
The ventilated seats will only function
when the engine is running.

The rear seat heat controls are located on
the rear door armrest.
To operate the heated seats:

E146309

To operate the ventilated seats, press the
ventilated seat symbol to cycle through
the various cooling settings and off. Cooler
settings are indicated by more indicator
lights.

E146322

•
•

Press this symbol for maximum heat.
Press again to turn off.

If the engine falls below 350 RPM while
the ventilated seats are on, the feature will
turn itself off. You will need to reactivate
it.

121

F150 (TF6) , enUSA

Seats
Heated and Ventilated Seats Air
Filter Replacement (If Equipped)

2. Push in on the center of the outside
edge of the filter and rotate clockwise
into the housing until it clips into
position.

The heated and ventilated seat system
includes air filters. You must replace them
periodically.

FRONT SEAT ARMREST (IF

The filter is located under each front seat.
Access the filter from the second row
foot-well area. Move the front seats all the
way to the full front and full up positions
to ease access.

EQUIPPED)

E166705

Press the release control to move the front
seat armrest up or down.

E146319

Pull out the optional drawer at the bottom
of the center seat to access the cup
holders.

To remove a filter:
1. Turn the vehicle off.
2. Push up on the outside rigid edge of
the filter until the tabs are released,
then remove the filter.

E166779

Lift the latch to open the lid and gain
access to the optional storage
compartment under the center seat
cushion.

E146321

To install a filter:
1.

First, position the filter in its housing
making sure that the far forward end
is all the way up in the housing.

122

F150 (TF6) , enUSA

Seats
REAR SEAT ARMREST (IF
EQUIPPED)

E162744

Pull the strap located on the center
seatback to access the armrest and
cupholders.
The cupholders are located inside the rear
seat armrest. To open the cupholders:
1.

Push in gently on the center of the
plastic panel on the front edge of the
armrest. The cupholders will partially
open.
2. Pull the cupholder fully open before
using.

123

F150 (TF6) , enUSA

Universal Garage Door Opener (If Equipped)
The appearance of your vehicle’s universal
garage door opener varies according to
your option package. Before programming,
make sure you identify which transmitter
you have by comparing it to the graphics
below:

WARNINGS
Do not use the system with any
garage door opener that does not
have the safety stop and reverse
feature as required by U.S. Federal Safety
Standards (this includes any garage door
opener manufactured before April 1, 1982).
Note: Before you begin the programming
process, park your vehicle in front of the
garage door opener motor or other device
you want to program.
Note: Make sure you keep the original
remote control transmitter for use in other
vehicles as well as for future system
programming.

E164776

Car2U Home Automation System

Note: We recommend that, upon the sale
or lease termination of your vehicle, you
erase the programmed function buttons for
security reasons. See Erasing the Function
Button Codes later in this section.
Note: Programming the system to a
community gate will require a unique set of
instructions depending on the gate system
model. Contact the help line at
1-866-572-2728 for further information.

E142657

HomeLink
Note: Programming these two types of
universal garage door openers are different,
and they have different instructions. Identify
your package and refer to the instructions
listed in this chapter.

Note: If you accidently enter the program
mode by pressing and releasing the outer
two buttons or all three buttons
simultaneously, do not press any button
until the module times out after a few
seconds and resets to normal mode. When
the module has timed out, all three LED
lamps will flash rapidly for a few seconds
then turn off. Any settings should remain as
previously set.

CAR2U® Home Automation
System (If Equipped)
WARNINGS
Make sure that the garage door and
security device are free from
obstruction when you are
programming. Do not program the system
with the vehicle in the garage.

The universal garage door opener replaces
the common hand-held garage door
opener with a three-button transmitter,
integrated into the driver’s sun visor.

124

F150 (TF6) , enUSA

Universal Garage Door Opener (If Equipped)
Note: If you cannot locate the learn button,
see the Owner’s Manual for your garage
door opener or call the toll-free help line at
1-866-572-2728.

The system includes two primary features,
a garage door opener and a platform for
remote activation of devices within the
home. This functionality allows you to
program garage door openers as well as
security devices and home lighting
systems.

3. Press the learn button on the garage
door opener motor.

You can find additional system information
online at www.learcar2U.com or by calling
the toll-free help line on 1-866-572-2728.

E142659

Note: You will have 10–30 seconds to
complete the following steps.
4. Return to your car.

E164776

5. Press and hold the function button you
would like to use to control the garage
door. You may need to hold the button
from 5–20 seconds, during which time the
selected button LED lamp will flash slowly.

Rolling Code Programming
Note: If you do not follow the time-sensitive
instructions, the device will time out and
you will have to repeat the complete
procedure.
Note: It may be helpful to have another
person assist you in programming the
transmitter.
1. Switch the ignition on.
2. Press and hold the outer two buttons for
1–2 seconds, then release.

E164776

6. When the garage door moves, release
the button within one second. The LED
lamp will flash rapidly until programming
is complete.
7. Press and release the button again. The
garage door should move, confirming that
programming is successful. If your garage
door does not operate, repeat the previous
steps.

E164777

Note: You may need a ladder to reach the
unit and you may need to remove the cover
or lamp lens.

The LED lamp above the selected button
will illuminate to confirm that the system
is responding to the button command.

125

F150 (TF6) , enUSA

Universal Garage Door Opener (If Equipped)
To program another rolling code device,
repeat Steps 1 through 6, substituting a
different function button in Step 5.

Note: You must complete the following
step within 2.5 minutes.
4. Enter the corresponding DIP switch
settings from left to right into the system
by pressing and releasing the buttons
corresponding to the settings you noted.

Fixed Code Programming
Note: It may be helpful to have another
person assist you in programming the
transmitter.

5. Simultaneously press and release all
three function buttons. The LED lamps will
illuminate.

To program units with fixed code DIP
switches, you will need the garage door
hand-held transmitter, paper and a pen or
pencil.
1. Switch the ignition on.
2. Open the battery cover and note all the
switch settings from left to right.

E164776

6. Press and hold the function button you
would like to use to control the garage
door.
Note: You may need to hold the button
from 5–55 seconds before observing
movement of the garage door.

E164778

•
•

•

When the switch is in the up, on, or +
position, mark down “left button”.
When the switch is in the middle,
neutral, or 0 position, mark down
“middle button”.
When the switch is in the down, off, or
– position, mark down “right button”.

7. When the garage door moves, release
the button within one second. After you
release the button, the LED lamp will flash
slowly.
8. The LED lamp will begin to flash rapidly
until programming is complete. If your
garage door does not operate, repeat the
previous steps. Otherwise, call the toll-free
help line at 1-866-572-2728.

3. Press all three function buttons
simultaneously for a few seconds and then
release. The LED lamps will flash slowly.

The LED lamp above the selected button
will illuminate to confirm that the system
is responding to the button command.
Erasing the Function Button Codes
Note: You cannot erase individual buttons.
1. Press and hold the outer two function
buttons simultaneously for approximately
20 seconds until the LED lamps above the
buttons flash rapidly

E164776

126

F150 (TF6) , enUSA

Universal Garage Door Opener (If Equipped)
Note: Make sure that the garage door and
security device are free from obstruction
when you are programming. Do not program
the system with the vehicle in the garage.
Note: Make sure you keep the original
remote control transmitter for use in other
vehicles as well as for future system
programming.

E164777

Note: We recommend that, upon the sale
or lease termination of your vehicle, you
erase the programmed function buttons for
security reasons. See Erasing the Button
Codes later in this section.

2. When the LED lamps flash, release the
buttons. You have erased all of the button
codes.
FCC and RSS-210 Industry Canada
Compliance

Note: You can program a maximum of
three devices. To change or replace any of
the three devices after you have
programmed them, you must first erase the
current settings. See Erasing the Button
Codes later in this section.

This device complies with Part 15 of the
FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the
following two conditions:
1.

This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause undesired
operation.
Changes or modifications to your device
not expressly approved by the party
responsible for compliance can void the
user’s authority to operate the equipment.

E142657

The universal garage door opener replaces
the common hand-held garage door
opener with a three-button transmitter,
integrated into the driver’s sun visor.

HomeLink Wireless Control
System (If Equipped)

WARNING
Do not use the system with any
garage door opener that does not
have the safety stop and reverse
feature as required by U.S. Federal Safety
Standards (this includes any garage door
opener manufactured before April 1, 1982).
A garage door opener that cannot detect
an object, signaling the door to stop and
reverse, does not meet current federal
safety standards. Using a garage door
opener without these features increases
the risk of serious injury or death.

You can find additional system information
online at www.homelink.com or by calling
the toll-free help line on 1-800-355-3515.

127

F150 (TF6) , enUSA

Universal Garage Door Opener (If Equipped)
In-vehicle Programming

If the indicator light flashes rapidly for two
seconds and then turns to a constant light,
you have not programmed the HomeLink
button yet. Do the following:

This process is to program your hand-held
transmitter and your in-vehicle HomeLink
button.

Press and hold the HomeLink button while
you press and release the hand-held
transmitter button every two seconds. The
HomeLink indicator light will flash slowly
and then rapidly once the HomeLink
function button recognizes and accepts
the hand-held transmitter’s radio
frequency signal.

Note: Put a new battery in the hand-held
transmitter. This will ensure quicker training
and accurate transmission of the
radio-frequency signal.

After programming the HomeLink button,
begin programming your garage door
opener motor.
Note: You may need a ladder to reach the
unit and you may need to remove the cover
or lamp lens on your garage door opener.

E142658

With your vehicle parked outside of the
garage, turn your ignition to the on
position, but do not start your vehicle.
2. Hold your hand-held garage door
transmitter 1–3 inches (2–8
centimeters) away from the HomeLink
button that you want to program.
3. Using both hands, simultaneously,
press and hold the desired HomeLink
button and the hand-held transmitter
button. DO NOT release either one until
the HomeLink indicator light flashes
slowly and then rapidly. When the
indicator light flashes rapidly, you can
release both buttons. The rapid
flashing indicates successful training.
4. Press and hold the HomeLink button
you programmed for five seconds, then
release. You may need to do this twice
to activate the door. If your garage door
does not operate, watch the HomeLink
indicator light.

E142659

To program additional buttons, repeat
Steps 1 – 4.
For questions or comments, please contact
HomeLink at www.homelink.com or
1-800-355-3515.
Programming Your Garage Door
Opener Motor
1.

Press the learn button on the garage
door opener motor and then you have
30 seconds to complete the next two
steps.
2. Return to your vehicle.

If the indicator light stays on, the
programming is complete. See
Programming Your Garage Door Motor
later in this section.

128

F150 (TF6) , enUSA

Universal Garage Door Opener (If Equipped)
2. The indicator light will begin to flash
after 20 seconds. Without releasing the
button, follow Step 1 in the
Programming section.
For questions or comments, contact
HomeLink at www.homelink.com or
1-800-355-3515.
E142658

Programming to a Genie Intellicode 2
Garage Door Opener

3. Press and hold the function button you
want to program for two seconds, then
release. Repeat this step. Depending
on your brand of garage door opener,
you may need to repeat this sequence
a third time.

Note: You must program the Genie
Intellicode 2 transmitter to operate it with
the garage door opener.
Note: To program HomeLink to the
transmitter, you must first put the
transmitter into programming mode.

Erasing the Function Button Codes
Note: You cannot erase individual buttons.

E142661
E142660

Press and hold the outer two function
buttons simultaneously for
approximately 20 seconds until the
indicator lights above the buttons flash
rapidly.
2. When the indicator lights flash, release
the buttons. You have erased the codes
for all buttons.

To program a device to a previously trained
button, follow these steps:
Press and hold the desired button. Do
NOT release the button.

129

F150 (TF6) , enUSA

Red indicator light

Green indicator light

Press and hold one of the buttons on
the hand-held transmitter for 10
seconds. The indicator light will change
from green to red and green.
2. Press the same button twice to confirm
the change to programming mode. If
done properly the indicator light will
appear red.
3. Hold the transmitter within 1–3 inches
(2–8 centimeters) of the button on the
visor you want to program.

Reprogramming a Single Button

Universal Garage Door Opener (If Equipped)
4. Press and hold both the programmed
Genie button on the hand-held
transmitter and the button you want
to program. The indicator light on the
visor will flash rapidly when the
programming is successful.
Note: The Genie transmitter will transmit
for up to 30 seconds. If HomeLink does not
program within 30 seconds you will need to
press the Genie transmitter again. If the
Genie transmitter indicator light displays
green and red, release the button until the
indicator light turns off before pressing the
button again.

Press and hold the program button on
the garage door opener motor until
both blue indicator lights turn on.
2. Release the program button. Only the
smaller round indicator light should be
on.
3. Press and release the program button.
The larger purple indicator light will
flash.
Note: The next two steps must be
completed in 30 seconds.
4. Press and release the previously
programmed button on the Genie
Intellicode 2 hand-held transmitter.
Both indicator lights on the garage door
opener motor unit should now flash
purple.
5. Press and hold the previously
programmed button on the visor for
two seconds. Repeat this step up to
three times until the garage door
moves.

Once you have programmed HomeLink
successfully, you must change the Genie
transmitter out of program mode. To do
this:
1.

Press and hold the previously
programmed Genie button on the
hand-held transmitter for 10 seconds.
The indicator light will change from red
to red and green.
2. Press the same button twice to confirm
the change. If done correctly the
indicator light will turn green.

Programming is now complete.
Clearing a HomeLink Device
To erase programming from the three
HomeLink buttons press and hold the two
outer HomeLink buttons until the indicator
light begins to flash. The indicator light will
begin flashing in 10-20 seconds. When this
happens, release both buttons. You have
now erased the programming, and the
indicator light should blink slowly to
indicate the device is in train mode when
you press any of the three HomeLink
buttons.

Programming HomeLink to the Genie
Intellicode Garage Door Opener Motor
Note: You may need a ladder to access the
garage door opener motor.

E142662

130

F150 (TF6) , enUSA

Universal Garage Door Opener (If Equipped)
FCC and RSS-210 Industry Canada
Compliance
This device complies with Part 15 of the
FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Changes or modifications to your device
not expressly approved by the party
responsible for compliance can void the
user’s authority to operate the equipment.

131

F150 (TF6) , enUSA

Auxiliary Power Points
12 Volt DC Power Point

•
•
•

WARNING
Do not plug optional electrical
accessories into the cigar lighter
socket (if equipped). Improper use
of the lighter can cause damage not
covered by your warranty, and can result
in fire or serious injury.

in the front of the center console
inside the center console storage bin
on the rear of the center console.

110 Volt AC Power Points (If Equipped)
WARNING
Do not keep electrical devices
plugged in the power points when
the devices are not in use. Do not use
any extension cord with the 110 volt AC
power points, since it will defeat the safety
protection design. Do not use a single
power point to power multiple devices. It
may cause the power point to exceed the
150 watt load limit and overload, resulting
in fire or serious injury.

Note: If used when the engine is not
running, the battery will discharge. There
may be insufficient power to restart your
engine.
Note: Do not insert objects other than an
accessory plug into the power point. This
will damage the outlet and blow the fuse.
Note: Do not hang any type of accessory or
accessory bracket from the plug.

Note: Keep the engine running to use the
power points.

Note: Do not use the power point over the
vehicle capacity of 12 volt DC 180 watts or
a fuse may blow.
Note: Do not use the power point for
operating a cigar lighter element.
Note: Improper use of the power point can
cause damage not covered by your
warranty.
Note: Always keep the power point caps
closed when not in use.
Run the engine for full capacity use of the
power point. To prevent the battery from
being discharged:
•

•

E143941

Some vehicles may come equipped with
more than one power point. One may be
located on the rear of the center console.
The second one (if equipped) may be
located on the instrument panel. You can
use your power points for powering
electrical devices that require up to 150
watts.

do not use the power point longer than
necessary when the engine is not
running
do not leave devices plugged in
overnight or when the vehicle is parked
for extended periods.

Locations
Power points may be found:

132

F150 (TF6) , enUSA

Auxiliary Power Points
When the indicator light, located on the
power point, is:
• on — the power point is ready to supply
power.
• off — the power point power supply is
off; ignition is not on.
• flashing — the power point is in fault
mode.
The power point temporarily turns off
power if the 150 watt limit is exceeded. It
can also switch to a fault mode when it is
overloaded, overheated, or shorted. Unplug
your device and switch the ignition off, and
then switch the ignition back on for
overloading and shorting conditions. Let
the system cool off, and then turn the
ignition off, and then switch the ignition
back on for an overheating condition.
The power points are not designed for
electric devices such as:
• cathode ray tube type televisions
• motor loads, for example vacuum
cleaners, electric saws and other
electric power tools, or
compressor-driven refrigerators
• measuring devices which process
precise data, for example medical
equipment or measuring equipment
• other appliances requiring an extremely
stable power supply, for example
microcomputer-controlled electric
blankets or touch sensor lamps.

133

F150 (TF6) , enUSA

Storage Compartments
CENTER CONSOLE (IF EQUIPPED)

OVERHEAD CONSOLE (IF
EQUIPPED)

Stow items in the cupholder carefully as
items may become loose during hard
braking, acceleration or collisions, including
hot drinks which may spill.

E75193

Press near the rear edge of the door to
open it.

E167704

Available console features include:
•
•

•
•

Locking storage compartment with
hanging file folder supports
Utility compartment with coin holder
slots, cardholder and pen holder (on
underside of lid)
Storage for laptop computer
12-volt power point inside the storage
compartment and one on the rear of
the console
Front and rear cupholders
Rear-passenger air registers.

134

F150 (TF6) , enUSA

Starting and Stopping the Engine
GENERAL INFORMATION

IGNITION SWITCH

WARNINGS
Extended idling at high engine
speeds can produce very high
temperatures in the engine and
exhaust system, creating the risk of fire or
other damage.

C
B
D

Do not park, idle or drive your vehicle
on dry grass or other dry ground
cover. The emission system heats up
the engine compartment and exhaust
system, creating the risk of fire.

E163165

Do not start the engine in a closed
garage or in other enclosed areas.
Exhaust fumes can be toxic. Always
open the garage door before you start the
engine.

A (off) - The ignition is off.
Note: When you switch the ignition off and
leave your vehicle, do not leave your key in
the ignition. This could cause your vehicle
battery to lose charge.

If you smell exhaust fumes inside
your vehicle, have your vehicle
checked by an authorized dealer
immediately. Do not drive your vehicle if
you smell exhaust fumes.

B (accessory) - Allows the electrical
accessories, such as the radio, to operate
while the engine is not running.
Note: Do not leave the ignition key in this
position for too long. This could cause your
vehicle battery to lose charge.

If you disconnect the battery, your vehicle
may exhibit some unusual driving
characteristics for approximately 5 miles
(8 kilometers) after you reconnect it. This
is because the engine management system
must realign itself with the engine. You can
disregard any unusual driving
characteristics during this period.

C (on) - All electrical circuits are
operational and the warning lamps and
indicators illuminate.
D (start) - Cranks the engine.

STARTING A GASOLINE
ENGINE

The powertrain control system meets all
Canadian interference-causing equipment
standard requirements regulating the
impulse electrical field or radio noise.

When you start the engine, the idle speed
increases, this helps to warm up the
engine. If the engine idle speed does not
slow down automatically, have your
vehicle checked by an authorized dealer.

When you start the engine, avoid pressing
the accelerator pedal before and during
operation. Only use the accelerator pedal
when you have difficulty starting the
engine.

135

F150 (TF6) , enUSA

Starting and Stopping the Engine
Stopping the Engine When Your
Vehicle is Moving

Before starting the engine check the
following:
• Make sure all occupants have fastened
their safety belts.
• Make sure the headlamps and
electrical accessories are off.
• Make sure the parking brake is on.
• Move the transmission selector lever
to position P.
• Turn the ignition key to the on position.

WARNING
Switching off the engine when the
vehicle is still moving will result in a
loss of brake and steering assistance.
The steering will not lock, but higher effort
will be required. When the ignition is
switched off, some electrical circuits,
warning lamps and indicators may also be
off.

Note: Do not touch the accelerator pedal.
1. Fully press the brake pedal.
2. Turn the key to the start position to
start the engine. Release the key when
the engine starts.
Note: The engine may continue cranking
for up to 15 seconds or until it starts.

Move the transmission selector lever
to position N and use the brakes to
bring your vehicle to a safe stop.
2. When your vehicle has stopped, move
the transmission selector lever to
position P and turn the key to the off
position.
3. Apply the parking brake.

Note: If you cannot start the engine on the
first try, wait for a short period and try again.

Cold Weather Starting (Flexible
Fuel Vehicles Only)

Failure to Start
If you cannot start the engine after three
attempts, wait 10 seconds and follow this
procedure:

The starting characteristics of all grades
of E85 ethanol make it unsuitable for use
when ambient temperatures fall below
0°F (-18°C). Consult your fuel distributor
for the availability of winter grade ethanol.
As the outside temperature approaches
freezing, ethanol fuel distributors should
supply winter grade ethanol (same as with
unleaded gasoline). If summer grade
ethanol is used in cold weather conditions,
0°F to 32°F (-18°C to 0°C), you may
experience increased cranking times, rough
idle or hesitation until the engine has
warmed up.

1. Fully press the brake pedal.
2. Fully press the accelerator pedal and
hold it there.
3. Start the engine.

Stopping the Engine When Your
Vehicle is Stationary
1.

Move the transmission selector lever
to position P.
2. Turn the key to the off position.
3. Apply the parking brake.

You may experience a decrease in peak
performance when the engine is cold when
operating on E85 ethanol.

136

F150 (TF6) , enUSA

Starting and Stopping the Engine
Important Ventilating Information

Do not crank the engine for more than 10
seconds at a time as starter damage may
occur. If the engine fails to start, turn the
key to off and wait 30 seconds before
trying again.

If you stop your vehicle and the leave the
engine idling for long periods of time, we
recommend that you do one of the
following:

Do not use starting fluid such as ether in
the air intake system. Such fluid could
cause immediate explosive damage to the
engine and possible personal injury.

•
•

If you should experience cold weather
starting problems on E85 ethanol, and
neither an alternative brand of E85 ethanol
nor an engine block heater is available, the
addition of unleaded gasoline to your tank
improves cold starting performance. Your
vehicle is designed to operate on E85
ethanol alone, unleaded gasoline alone, or
any mixture of the two.

ENGINE BLOCK HEATER (IF
EQUIPPED)

WARNINGS
Failure to follow engine block heater
instructions could result in property
damage or serious personal injury.
Do not use your heater with
ungrounded electrical systems or
two-pronged adapters. There is a risk
of electrical shock.

If the Engine Fails to Start Using the
Preceding Instructions (Flexible Fuel
Vehicles Only)
1.

Press and hold down the accelerator
one-third to one-half the way to the
floor, then crank the engine.
2. When the engine starts, release the
key, then gradually release the
accelerator pedal as the engine speeds
up. If the engine still fails to start,
repeat Step 1.

Note: The heater is most effective when
outdoor temperatures are below 0°F
(-18°C).
The heater acts as a starting aid by
warming the engine coolant. This allows
the climate control system to respond
quickly. The equipment includes a heater
element (installed in the engine block) and
a wire harness. You can connect the
system to a grounded 120-volt AC
electrical source.

Guarding Against Exhaust Fumes
WARNING
If you smell exhaust fumes inside
your vehicle, have your vehicle
checked by your authorized dealer
immediately. Do not drive your vehicle if
you smell exhaust fumes. Carbon
monoxide is present in exhaust fumes.
Take precautions to avoid its dangerous
effects.

We recommend that you do the following
for a safe and correct operation:
• Use a 16-gauge outdoor extension cord
that is product certified by
Underwriter’s Laboratory (UL) or
Canadian Standards Association
(CSA). This extension cord must be
suitable for use outdoors, in cold

137

F150 (TF6) , enUSA

Open the windows at least 1 inch (2.5
centimeters)
Set your climate control to outside air.

Starting and Stopping the Engine

•
•
•

•

temperatures, and be clearly marked
Suitable for Use with Outdoor
Appliances. Do not use an indoor
extension cord outdoors. This could
result in an electric shock or become a
fire hazard.
Use as short an extension cord as
possible.
Do not use multiple extension cords.
Make sure that when in operation, the
extension cord plug and heater cord
plug connections are free and clear of
water. This could cause an electric
shock or fire.
Make sure your vehicle is parked in a
clean area, clear of combustibles.
Make sure the heater, heater cord and
extension cord are firmly connected.
Check for heat anywhere in the
electrical hookup once the system has
been operating for approximately 30
minutes.
Make sure the system is unplugged and
properly stowed before driving your
vehicle. Make sure the protective cover
seals the prongs of the block heater
cord plug when not in use.
Make sure the heater system is
checked for proper operation before
winter.

Using the Engine Block Heater
Make sure the receptacle terminals are
clean and dry prior to use. Clean them with
a dry cloth if necessary.
The heater uses 0.4 to 1.0 kilowatt-hours
of energy per hour of use. The system does
not have a thermostat. It achieves
maximum temperature after
approximately three hours of operation.
Using the heater longer than three hours
does not improve system performance and
unnecessarily uses electricity.

138

F150 (TF6) , enUSA

Fuel and Refueling
•

SAFETY PRECAUTIONS
WARNINGS
Do not overfill the fuel tank. The
pressure in an overfilled tank may
cause leakage and lead to fuel spray
and fire.

•

The fuel system may be under
pressure. If you hear a hissing sound
near the fuel filler door, do not refuel
until the sound stops. Otherwise, fuel may
spray out, which could cause serious
personal injury.

•

Automotive fuels can cause serious
injury or death if you misuse or
mishandle them.
Fuel ethanol and gasoline may
contain benzene, which is a
cancer-causing agent.

•

When refueling always shut the
engine off and never allow sparks or
open flames near the filler neck.
Never smoke or use a cell phone while
refueling. Fuel vapor is extremely
hazardous under certain conditions. Avoid
inhaling excess fumes.

•

The flow of fuel through a fuel pump
nozzle can produce static electricity,
which can cause a fire if you pump
fuel into an ungrounded fuel container.
Observe the following guidelines when
handling automotive fuel:

•

139

F150 (TF6) , enUSA

Extinguish all smoking materials and
any open flames before refueling your
vehicle.
Automotive fuels can be harmful or
fatal if swallowed. Fuel such as
gasoline is highly toxic and if
swallowed can cause death or
permanent injury. If swallowed, call a
physician immediately, even if no
symptoms are immediately apparent.
The toxic effects of fuel may not be
visible for hours.
Avoid inhaling fuel vapors. Inhaling too
much fuel vapor of any kind can lead
to eye and respiratory tract irritation.
In severe cases, excessive or prolonged
breathing of fuel vapor can cause
serious illness and permanent injury.
Avoid getting fuel liquid in your eyes. If
you splash fuel in your eyes, remove
contact lenses (if worn), flush with
water for 15 minutes and seek medical
attention. Failure to seek proper
medical attention could lead to
permanent injury.
Fuels can also be harmful if absorbed
through the skin. If you splash fuel on
your skin, clothing or both, promptly
remove contaminated clothing and
wash your skin thoroughly with soap
and water. Repeated or prolonged skin
contact with fuel liquid or vapor causes
skin irritation.
Be particularly careful if you are taking
“Antabuse” or other forms of disulfiram
for the treatment of alcoholism.
Breathing gasoline vapors, or skin
contact could cause an adverse
reaction. In sensitive individuals, serious
personal injury or sickness may result.
If you splash fuel on your skin, promptly
wash your skin thoroughly with soap
and water. Consult a physician
immediately if you experience an
adverse reaction.

Fuel and Refueling
Do not use:

FUEL QUALITY

•

Use of any fuel other than those
recommended may cause powertrain
damage and a loss of vehicle performance;
repairs may not be covered under warranty.

•
•

Choosing the Right Fuel Without
a Flex Fuel Vehicle (If Equipped)

•

Use only UNLEADED gasoline or
UNLEADED gasoline blended with a
maximum of 15% ethanol in your gasoline
vehicle. If your vehicle is a Flex Fuel Vehicle
(FFV), it will have a yellow bezel placed
over the fuel fill inlet.

•

Note: Use of any fuel other than
recommended fuel can cause powertrain
damage, impair the emission control system
or cause loss of vehicle performance. Any
damage to vehicle that is caused by use of
fuel not recommended will not be covered
under warranty.

Do not use:
•
•
•

•

Fuel containing more than 15% ethanol
or E-85 fuel.
Fuel with methanol.
Fuels containing metallic based
additives, including manganese-based
compounds.
Fuels containing the octane booster
additive, methylcyclopentadienyl
manganese tricarbonyl (MMT)
Leaded fuel (The use of leaded fuel is
prohibited by law).

Octane Recommendations

E161513

Do not be concerned if your engine
sometimes knocks lightly. However, if it
knocks heavily under most driving
conditions while you are using fuel with the
recommended octane rating, see your
authorized dealer to prevent any engine
damage.

Choosing the Right Fuel With a
Flex Fuel Vehicle (If Equipped)
Use only UNLEADED gasoline or
UNLEADED gasoline blended with a
maximum of 85% ethanol (E-85) in your
Flex Fuel Vehicle (FFV). If your vehicle is
flex fuel capable, it will have a yellow bezel
placed over the fuel fill inlet.

140

F150 (TF6) , enUSA

Fuels containing more than 85%
ethanol or E-100 fuel.
Fuel with methanol.
Fuels containing metallic based
additives, including manganese-based
compounds.
Fuels containing the octane booster
additive, methylcyclopentadienyl
manganese tricarbonyl (MMT)
Leaded fuel (The use of leaded fuel is
prohibited by law).

Fuel and Refueling
•

3.7L V6, 5.0L V8 and 6.2L V8 Engines
Regular unleaded gasoline with a pump
(R+M)/2 octane rating of 87 is
recommended. Some stations offer fuels
posted as Regular with an octane rating
below 87, particularly in high altitude areas.
Fuels with octane levels below 87 are not
recommended.

•

Refilling With a Portable Fuel
Container

3.5L V6 EcoBoost Engine
Regular unleaded gasoline with a pump
(R+M)/2 octane rating of 87 is
recommended. Some stations offer fuels
posted as Regular with an octane rating
below 87, particularly in high altitude areas.
Fuels with octane levels below 87 are not
recommended.

WARNINGS
Do not insert the nozzle of portable
fuel containers or aftermarket
funnels into the Easy Fuel “no cap”
fuel system. This could damage the fuel
system and its seal, and may cause fuel to
run onto the ground instead of filling the
tank, which could result in serious personal
injury.

Premium fuel will provide improved
performance and is recommended for
severe duty usage such as trailer tow.

Do not try to pry open or push open
the Easy Fuel “no cap” fuel system
with foreign objects. This could
damage the fuel system and its seal and
cause injury to you or others.

RUNNING OUT OF FUEL
Avoid running out of fuel. This situation
may have an adverse effect on powertrain
components.

Note: When filling the vehicle’s fuel tank
from a portable fuel container, use the
funnel included with the vehicle.

If you have run out of fuel:
•

•

The service engine soon indicator may
come on. For more information on the
service engine soon indicator, See
Warning Lamps and Indicators
(page 82).
For information on calculating DTE
(Distance to empty), See Instrument
Cluster (page 81).

You may need to cycle the ignition from
Off to On several times after refueling
to allow the fuel system to pump the
fuel from the fuel tank to the engine.
On restarting, cranking time will take a
few seconds longer than normal.
Normally, adding 1 gallon (3.8 liters) of
fuel is enough to restart the engine. If
the vehicle is out of fuel and on a steep
grade, more than 1 gallon (3.8 liters)
may be required.

With the Easy Fuel “no cap” fuel system,
use the following directions when filling
from a portable fuel container:

E142668

141

F150 (TF6) , enUSA

Fuel and Refueling
1.

Locate the white plastic funnel.
• In SuperCab and SuperCrew
vehicles, it is located under the
second row driver side seat near
the spare tire toolbox.
• On regular cab vehicles, the funnel
is located behind the driver seat.
Slowly insert the portable fuel
container into the fuel filler opening.
2. Fill the vehicle with fuel from the
portable fuel container.
3. When done, clean the funnel or
properly dispose of it. You can
purchase extra funnels from your
authorized dealer if you choose to
dispose of the funnel. Do not use
aftermarket funnels; they will not work
with the Easy Fuel system and can
damage it. The included funnel has
been specially designed to work safely
with your vehicle.

WARNINGS
Do not use personal electronic
devices while refueling.
Use the following guidelines to avoid
electrostatic charge build-up when filling
an ungrounded fuel container:
•
•
•
•

Place approved fuel container on the
ground.
Do not fill a fuel container while it is in
the vehicle (including the cargo area).
Keep the fuel pump nozzle in contact
with the fuel container while filling.
Do not use a device that would hold
the fuel pump handle in the fill position.

Easy Fuel™ Capless Fuel System
WARNING
The fuel system may be under
pressure. If you hear a hissing sound
near the fuel filler door, do not refuel
until the sound stops. Otherwise, fuel may
spray out, which could cause serious
personal injury.

REFUELING
WARNINGS
Fuel vapor burns violently and a fuel
fire can cause severe injuries.

When fueling your vehicle:

Read and follow all the instructions
on the pump island.

Put the vehicle in P (Park) and turn the
ignition off.
2. Open the fuel filler door.

Turn off your engine when you are
refueling.
Do not smoke if you are near fuel or
refueling your vehicle.
Keep sparks, flames and smoking
materials away from fuel.
Stay outside your vehicle and do not
leave the fuel pump unattended
when refueling your vehicle. This is
against the law in some places.
Keep children away from the fuel
pump; never let children pump fuel.

E156032

142

F150 (TF6) , enUSA

Fuel and Refueling
4. Insert either the fuel fill nozzle or the
fuel fill funnel provided with the vehicle
several times to allow the inlet to close
properly. This will dislodge any debris
preventing the inlet from sealing.

3. Slowly insert the fuel filler nozzle fully
into the fuel system, and leave the
nozzle fully inserted to open both doors
until you are done pumping. Hold
handle higher during insertion for easier
access.

If this action corrects the problem, the
message may not reset immediately. It
may take several driving cycles for the
message to turn off. A driving cycle
consists of an engine start-up (after 4 or
more hours with the engine off) followed
by city or highway driving. Continuing to
drive with the message on may cause the
service engine soon lamp to turn on as
well.

FUEL CONSUMPTION

E154765

4. After you are done pumping fuel, slowly
remove the fuel filler nozzle—allow
about 5 to 10 seconds after pumping
fuel before removing the fuel filler
nozzle. This allows residual fuel to
drain back into the fuel tank and not
spill onto the vehicle.
Note: A fuel spillage concern may occur if
overfilling the fuel tank. Do not overfill the
tank. The fill pipe is equiped with a drain
hole. Excess fuel due to overfill may drain
through the drain hole and drip onto the
ground."

Empty reserve is the amount of fuel
remaining in the tank after the fuel gauge
indicates empty. The amount of usable
fuel in the empty reserve varies and should
not be relied upon to increase driving range.
•

•

If the fuel fill inlet was not properly closed,
a Check Fuel Fill Inlet message may
appear on the instrument cluster.

•

At the next opportunity, do the following:
1. Safely pull off the road.
2. Put the vehicle in P (Park) and turn the
ignition off.
3. Open the fuel filler door and remove
any visible debris from the fuel fill
opening.

Filling the Tank
For consistent results when filling the fuel
tank:

143

F150 (TF6) , enUSA

The usable capacity of the fuel tank is
the amount of fuel that can be added
into the tank after the gauge indicates
empty
The advertised capacity is the total fuel
tank size. See Capacities and
Specifications (page 296). It is the
combined usable capacity plus the
empty reserve.
Due to the empty reserve, you may not
be able to refuel the full amount of the
advertised capacity of the fuel tank
even when the fuel gauge reads empty.

Fuel and Refueling
•

•

Turn the ignition off before fueling; an
inaccurate reading results if the engine
is left running.
Use the same fill rate
(low-medium-high) each time the tank
is filled.
Allow no more than two automatic
click-offs when filling.

Conditions
•

•

Results are most accurate when the filling
method is consistent.

•

Calculating Fuel Economy
Do not measure fuel economy during the
first 1000 miles (1600 kilometers) of
driving (this is your engine’s break-in
period); a more accurate measurement is
obtained after 2000 miles - 3000 miles
(3200 kilometers - 4800 kilometers). Also,
fuel expense, frequency of fill ups or fuel
gauge readings are not accurate ways to
measure fuel economy.
1.
2.
3.

4.
5.

•
•

•

Fill the fuel tank completely and record
the initial odometer reading.
Each time you fill the tank, record the
amount of fuel added.
After at least 3 to 5 tank fill ups, fill the
fuel tank and record the current
odometer reading.
Subtract your initial odometer reading
from the current odometer reading.
Calculate fuel economy by dividing
miles traveled by gallons used (For
Metric: Multiply liters used by 100, then
divide by kilometers traveled).

•

EMISSION CONTROL SYSTEM
WARNINGS
Do not park, idle, or drive your vehicle
in dry grass or other dry ground cover.
The emission system heats up the
engine compartment and exhaust system,
which can start a fire.

Keep a record for at least 1 month and
record the type of driving (city or highway).
This provides an accurate estimate of the
vehicle’s fuel economy under current
driving conditions. Additionally, keeping
records during summer and winter show
how temperature impacts fuel economy.
In general, lower temperatures mean lower
fuel economy.

Exhaust leaks may result in entry of
harmful and potentially lethal fumes
into the passenger compartment. If
you smell exhaust fumes inside your
vehicle, have your dealer inspect your
vehicle immediately. Do not drive if you
smell exhaust fumes.

144

F150 (TF6) , enUSA

Heavily loading a vehicle or towing a
trailer may reduce fuel economy at any
speed.
Carrying unnecessary weight may
reduce fuel economy (approximately
1 mpg [0.4 km/L] is lost for every 400
pounds [180 kilograms] of weight
carried).
Adding certain accessories to your
vehicle (for example bug deflectors,
rollbars/light bars, running boards, ski
racks) may reduce fuel economy.
Using fuel blended with alcohol may
lower fuel economy.
Fuel economy may decrease with lower
temperatures during the first 8–10
miles (12–16 kilometers) of driving.
Driving on flat terrain offers improved
fuel economy as compared to driving
on hilly terrain.
Transmissions give their best fuel
economy when operated in the top
cruise gear and with steady pressure
on the gas pedal.
Close windows for high speed driving.

Fuel and Refueling
Your vehicle is equipped with various
emission control components and a
catalytic converter that will enable your
vehicle to comply with applicable exhaust
emission standards. To make sure that the
catalytic converter and other emission
control components continue to work
properly:
•
•
•

•

an emission control device or prevent it
from working. Information about your
vehicle’s emission system is on the Vehicle
Emission Control Information Decal
located on or near the engine. This decal
also lists engine displacement
Please consult your warranty information
for complete details.

Use only the specified fuel listed.
Avoid running out of fuel.
Do not turn off the ignition while your
vehicle is moving, especially at high
speeds.
Have the items listed in scheduled
maintenance information performed
according to the specified schedule.

On-Board Diagnostics (OBD-II)
Your vehicle is equipped with an on-board
diagnostics system (OBD-II) that monitors
the engine’s emission control system. This
system protects the environment by
ensuring that your vehicle continues to
meet government emission standards. The
OBD-II system also assists your authorized
dealer in properly servicing your vehicle.

The scheduled maintenance items listed
in scheduled maintenance information are
essential to the life and performance of
your vehicle and to its emissions system.

When the service engine soon
indicator illuminates, the OBD-II
system has detected a
malfunction. Temporary malfunctions may
cause the service engine soon indicator to
illuminate.

If you use parts other than Ford, Motorcraft
or Ford-authorized parts for maintenance
replacements, or for service of
components affecting emission control,
such non-Ford parts should be the
equivalent to genuine Ford Motor Company
parts in performance and durability.

Examples of temporary malfunctions are:
•

Illumination of the service engine soon
indicator, charging system warning light or
the temperature warning light, fluid leaks,
strange odors, smoke or loss of engine
power could indicate that the emission
control system is not working properly.

•

An improperly operating or damaged
exhaust system may allow exhaust to
enter the vehicle. Have a damaged or
improperly operating exhaust system
inspected and repaired immediately.

•

You can correct these temporary
malfunctions by filling the fuel tank with
good quality fuel, properly closing the fuel
fill inlet or letting the electrical system dry
out. After three driving cycles without these
or any other temporary malfunctions

Do not make any unauthorized changes to
your vehicle or engine. By law, vehicle
owners and anyone who manufactures,
repairs, services, sells, leases, trades
vehicles, or supervises a fleet of vehicles
are not permitted to intentionally remove

145

F150 (TF6) , enUSA

the vehicle has run out of fuel—the
engine may misfire or run poorly
poor fuel quality or water in the
fuel—the engine may misfire or run
poorly
the fuel fill inlet may not have been
properly closed See Refueling (page
142).
driving through deep water—the
electrical system may be wet.

Fuel and Refueling
present, the service engine soon indicator
should stay off the next time you start the
engine. A driving cycle consists of a cold
engine startup followed by mixed
city/highway driving. No additional vehicle
service is required.

If the vehicle’s engine or transmission has
just been serviced, or the battery has
recently run down or been replaced, the
OBD-II system may indicate that the
vehicle is not ready for I/M testing. To
determine if the vehicle is ready for I/M
testing, turn the ignition key to the on
position for 15 seconds without cranking
the engine. If the service engine soon
indicator blinks eight times, it means that
the vehicle is not ready for I/M testing; if
the service engine soon indicator stays on
solid, it means that the vehicle is ready for
I/M testing.

If the service engine soon indicator remains
on, have your vehicle serviced at the first
available opportunity. Although some
malfunctions detected by the OBD-II may
not have symptoms that are apparent,
continued driving with the service engine
soon indicator on can result in increased
emissions, lower fuel economy, reduced
engine and transmission smoothness, and
lead to more costly repairs.

The OBD-II system monitors the emission
control system during normal driving. A
complete check may take several days. If
the vehicle is not ready for I/M testing, you
may need to perform the following driving
cycle consisting of mixed city and highway
driving:

Readiness for
Inspection/Maintenance (I/M)
Testing
Some state/provincial and local
governments may have
Inspection/Maintenance (I/M) programs
to inspect the emission control equipment
on your vehicle. Failure to pass this
inspection could prevent you from getting
a vehicle registration.

Drive on an expressway or highway for a
steady 15 minutes, followed by 20 minutes
of stop-and-go driving with at least four
30-second idle periods.
Allow the vehicle to sit for at least eight
hours without starting the engine. Then,
start the engine and complete the above
driving cycle. The engine must warm up to
its normal operating temperature. Once
started, do not turn off the engine until the
above driving cycle is complete. If the
vehicle is still not ready for I/M testing, you
will have to repeat the above driving cycle.

If the service engine soon
indicator is on or the bulb does
not work, you may need to have
the vehicle serviced. See On-Board
Diagnostics (OBD-II).
Your vehicle may not pass the I/M test if
the service engine soon indicator is on or
not working properly (bulb is burned out),
or if the OBD-II system has determined
that some of the emission control systems
have not been properly checked. In this
case, your vehicle is not ready for I/M
testing.

146

F150 (TF6) , enUSA

Transmission
R (Reverse)

AUTOMATIC TRANSMISSION

With the gearshift lever in R (Reverse), the
vehicle will move backward. Always come
to a complete stop before shifting into and
out of R (Reverse).

WARNINGS
Always set the parking brake fully
and make sure the gearshift is
latched in P (Park). Turn the ignition
to the off position and remove the key
whenever you leave your vehicle.

N (Neutral)
With the gearshift lever in N (Neutral), the
vehicle can be started and is free to roll.
Hold the brake pedal down while in this
position.

Do not use the tow/haul feature
when driving in icy or slippery
conditions as the increased engine
braking can cause the rear wheels to slide
and the vehicle to swing around with the
possible loss of vehicle control.

D (Overdrive) with Tow/Haul off
D (Overdrive) with tow/haul off is the
normal driving position for the best fuel
economy. The overdrive function allows
automatic upshifts and downshifts through
gears one through six.

Understanding the Shift Positions
of a 6–Speed Automatic
Transmission (If Equipped)

D (Overdrive) with Tow/Haul on
Column-shift transmission:

E166923

Putting your vehicle in or out of gear:
E163182

1. Fully press down the brake pedal.
2. Move the gearshift lever into the
desired gear.
3. Come to a complete stop.
4. Move the gearshift lever and securely
latch it in P (Park).

Floor-shift transmission:

P (Park)
This position locks the transmission and
prevents the rear wheels from turning.

147

F150 (TF6) , enUSA

Transmission
WARNING
Do not use the tow/haul feature
when driving in icy or slippery
conditions as the increased engine
braking can cause the rear wheels to slide
and the vehicle to swing around with the
possible loss of vehicle control.
M (Manual) without Overdrive
With the gearshift lever in M (Manual), the
driver can change gears up or down as
desired. This is called SelectShift
Automatic™ transmission (SST) mode.
By moving the gearshift lever from drive
position D (Overdrive) to M (Manual) you
now have control of selecting the gear you
desire using buttons on the shift lever.

E166925

The tow/haul feature improves
transmission operation when towing a
trailer or a heavy load. All transmission
gear ranges are available when using
tow/haul.
To activate tow/haul, press the
button on the gearshift lever.
The TOW HAUL indicator light
will illuminate in the instrument cluster.

To return to normal D (Overdrive) position,
move the shift lever back from M to D.

E161509

The transmission will operate in gears one
through six.

Tow/haul delays upshifts to reduce
frequency of transmission shifting.
Tow/haul also provides engine braking in
all forward gears when the transmission is
in the D (Overdrive) position; this engine
braking will slow the vehicle and assist the
driver in controlling the vehicle when
descending a grade. Depending on driving
conditions and load conditions, the
transmission may downshift, slow the
vehicle and control the vehicle speed when
descending a hill, without the accelerator
pedal being pressed. The amount of
downshift braking provided will vary based
upon the amount the brake pedal is
pressed.

2 (Second)
Use 2 (Second) to start-up on slippery
roads or to provide additional engine
braking on downgrades.
1 (First)
•
•
•

To deactivate the tow/haul feature and
return to normal driving mode, press the
button on the end of the gearshift lever.
The TOW HAUL light will no longer be
illuminated.

Forced downshifts
•
•
•

Tow/haul will also deactivate when the
vehicle is powered down.

148

F150 (TF6) , enUSA

Provides maximum engine braking
Allows upshifts by moving gearshift
lever
The transmission will not downshift
into 1 (First) at high speeds; it will
downshift to a lower gear and then
shift into 1 (First) when the vehicle
reaches slower speeds.

Allowed in D (Overdrive) with the
tow/haul feature on or off
Press the accelerator to the floor
Allows transmission to select an
appropriate gear

Transmission
Understanding your SelectShift
Automatic® transmission (If Equipped)

Floor-shift transmission:

Your vehicle is equipped with a SelectShift
Automatic™ transmission gearshift lever.
The SelectShift Automatic transmission
gives you the ability to change gears up or
down (without a clutch) as desired. The
SelectShift Automatic transmission
feature has two modes: PRS and M mode.
By moving the gearshift lever from the D
(Drive) position to the M (Manual) position
you may now manually select the gear you
desire. Only the current gear will be
displayed.

E166923

Use the buttons on the gearshift lever to
manually select gears. Press the + button
to upshift or the – button to downshift.

Column-shift transmission:

When manual control is no longer desired,
return the transmission to the D (Drive)
position.
Recommended shift speeds
Upshift according to the following chart:

E163184

Upshifts when accelerating (recommended for best fuel economy)

Shift from:
1–2

15 mph (24 km/h)

2–3

25 mph (40 km/h)

3–4

40 mph (64 km/h)

4–5

45 mph (72 km/h)

5–6

50 mph (80 km/h)

149

F150 (TF6) , enUSA

Transmission
In order to prevent the engine from running
at too low an RPM, which may cause it to
stall, SelectShift will still automatically
make some downshifts if it has determined
that you have not downshifted in time.
Although SelectShift will make some
downshifts for you, it will still allow you to
downshift at any time as long as the
SelectShift determines that the engine will
not be damaged from over-revving.

durability of the transmission. Over time,
the adaptive learning process will fully
update transmission operation.
Additionally, whenever the battery is
disconnected or a new battery installed,
the strategy must be relearned.

Brake-Shift Interlock
WARNINGS
Do not drive your vehicle until you
verify that the brake lamps are
working.

SelectShift will not automatically upshift,
even if the engine is approaching the RPM
limit. It must be shifted manually by
pressing the + button.

When doing this procedure, you will
be taking the vehicle out of park
which means the vehicle can roll
freely. To avoid unwanted vehicle
movement, always fully set the parking
brake prior to doing this procedure. Use
wheel chocks if appropriate.

Note: Engine damage may occur if
excessive engine revving is held without
shifting.
PRS (Progressive Range Selection)
With the gearshift lever in D (Drive), press
the – button to active PRS. The available
and selected gears will be indicated on the
instrument cluster.

If the parking brake is fully released,
but the brake warning lamp remains
illuminated, the brakes may not be
working properly. See your authorized
dealer.

All available gears will be displayed with
the current gear indicated. Press the –
button again to lock out gears beginning
with the highest gear. Example: press the
– button twice to lock out 6th and 5th
gears. Only the available gears will be
displayed and the transmission will
automatically shift between the available
gears. Press the + button to unlock gears
to allow the transmission to shift to higher
gears. The transmission will shift
automatically within the gear range you
select.

Your vehicle is equipped with a brake-shift
interlock feature that prevents the
gearshift lever from being moved from P
(Park) when the ignition is in the on
position and the brake pedal is not pressed.
If you cannot move the gearshift lever out
of P (Park) position with the ignition in the
on position and the brake pedal pressed,
a malfunction may have occurred. It is
possible that a fuse has blown or the
vehicle’s brake lamps are not operating
properly. See Fuse Specification Chart
(page 225).

Automatic Transmission Adaptive
Learning

If the fuse is not blown and the brake
lamps are working properly, the following
procedure will allow you to move the
gearshift lever from P (Park):

This feature is designed to increase
durability and provide consistent shift feel
over the life of the vehicle. A new vehicle
or transmission may have firm shifts, soft
shifts or both. This operation is considered
normal and will not affect function or

150

F150 (TF6) , enUSA

Transmission
Column-shifter
1.

3.
4.

5.
6.

Apply the parking brake. Turn the
ignition key to the off position, then
remove the key.
Move the steering column to the full
down and full rearward position
(toward the driver’s seat).
Remove the gearshift lever boot.
Place fingers into hole where the
gearshift lever boot was removed from
and pull top half of shroud up and
forward to separate it from the lower
half of the shroud. There is a hinge at
the forward edge of the top shroud.
Roll the top half of the shroud upward
on the hinge point to clear the hazard
flasher button, then pull straight
rearward toward the driver’s seat to
remove.
Remove the top half of the shroud.
Remove the three fasteners under the
column that secure the lower shroud
half to the column.

E163186

8. Apply the brake and move the gearshift
lever into N (Neutral).
9. Start the vehicle.
Perform Steps 4 through 8 in reverse order,
making sure to engage the hinge pivots
between the upper and lower halves of the
shroud. Keep slight pressure in the forward
direction as the halves are rotated
together.
Floor-shifter
1.

Apply the parking brake. Turn the
ignition key to the off position, then
remove the key.
2. Starting at the rear of the trim panel,
using a screwdriver (or similar tool)
carefully pry up the trim panel from
rear attachments and disconnect it
from the console to expose the inside
of the gearshift.

E163185

Pull the lock lever into the full unlocked
position and remove the lower shroud
cover by pulling the lever handle
through the slot in the cover.

E166929

151

F150 (TF6) , enUSA

Transmission
3. Locate the brake shift interlock lever
on the passenger side of the shifter
assembly.

E166930

4. Apply the brake pedal. Using a
screwdriver (or similar tool), press and
hold the brake shift interlock lever
while pulling the gearshift lever out of
the P (Park) position and into the N
(Neutral) position.
5. Install the trim panel.
6. Apply brake pedal, start the vehicle,
and release the parking brake. See your
authorized dealer as soon as possible
if this procedure is used.

If Your Vehicle Gets Stuck In Mud
or Snow
Note: Do not rock the vehicle if the engine
is not at normal operating temperature or
damage to the transmission may occur.
Note: Do not rock the vehicle for more than
a minute or damage to the transmission and
tires may occur, or the engine may overheat.
If your vehicle gets stuck in mud or snow,
it may be rocked out by shifting between
forward and reverse gears, stopping
between shifts in a steady pattern. Press
lightly on the accelerator in each gear.

152

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
4X4 LOW

USING FOUR-WHEEL DRIVE

Continuously illuminates when
4L is selected.

WARNING
E163174

For important information regarding
safe operation of this type of vehicle,
see General Information in the
Wheels and Tires chapter.

CHECK 4X4
Displays when a 4X4 fault is
present.

Note: Do not use 4X4 mode on dry, hard
surfaced roads. Doing so will produce
excessive noise, increase tire wear and may
damage drive components. 4X4 mode is
only intended for consistently slippery or
loose surfaces.

Using the Electronic Shift on the
Fly 4WD system (If Equipped)

Note: If 4X4 low is selected while the
vehicle is moving above 3 mph (5 km/h),
the 4WD system will not perform a shift.
This is normal and should be no reason for
concern. Refer to Shifting to or from 4L (4X4
Low) for proper operation.

4WD Indicator Lights
Note: When a 4X4 system fault is present,
the system will typically remain in whichever
4X4 mode was selected prior to the fault
condition occurring. It will not default to 4X2
in all circumstances. When this warning is
displayed, have your vehicle serviced by an
authorized dealer.

E163190

2H (4X2)
For general on-road driving. Sends power
to the rear wheels only and should be used
for street and highway driving. Provides
optimal smoothness and fuel economy at
high speeds.

4X2
Momentarily illuminates when
2H is selected.

4H (4X4 HIGH)
Used for extra traction such as in snow or
icy roads or in off road situations. This
mode is not intended for use on dry
pavement.

E163173

4X4 Auto

E166922

Continuously illuminates when
4A is selected (2-Speed
Automatic 4WD vehicles only)

Note: Do not use 4H (4X4 HIGH) on dry,
hard surfaced roads. Doing so can produce
excessive noise and increased tire wear. 4H
(4X4 HIGH) is only intended for consistently
slippery or loose surfaces.

4X4 HIGH
Continuously illuminates when
4H is selected.
E163175

153

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
4L (4X4 LOW)

Note: 4x4 low mode is not intended for use
on dry pavement.

Uses extra gearing to provide maximum
power to all four wheels at reduced
speeds. Intended only for off-road
applications such as deep sand, steep
grades, or pulling heavy objects. 4L (4x4
low) will not engage while the vehicle is
moving above 3 mph (5 km/h); this is
normal and should be no reason for
concern. Refer to Shifting to or from 4L
(4x4 low) for proper operation.

Bring the vehicle to a speed of 3 mph
(5 km/h) or less.
2. Place the transmission in N (Neutral).
3. Move the 4WD control to the desired
position.
The information display will display a
message indicating a 4X4 shift is in
progress. The information display will then
display the system mode selected. If any
of the above shift conditions are not met,
the shift will not occur and the information
display will display information guiding the
driver through the proper shifting
procedures.

Note: Do not use 4L (4X4 LOW) on dry,
hard surfaced roads. Doing so can produce
excessive noise and increased tire wear. 4L
(4X4 LOW) is only intended for consistently
slippery or loose surfaces. Use of 4L (4X4
LOW) on these surfaces may produce some
noise (such as occasional clunks), but will
not damage drive components.

If SHIFT DELAYED PULL FORWARD
displays in the information display, a
transfer case gear tooth blockage is
present. To alleviate this condition, place
the transmission in a forward gear, move
your vehicle forward approximately 5 feet
(1.5 meters), and shift the transmission
back to N neutral to allow the transfer case
to complete the range shift.

Note: The AdvanceTrac system has the
ability to take over control of the transfer
case clutch and disable it during driving
maneuvers when necessary.
Shifting between system modes
Note: Momentarily releasing the accelerator
pedal while performing a shift will improve
engagement/disengagement times.

Using the 2-Speed Automatic 4WD
System (If Equipped)

Note: Do not perform this operation if the
rear wheels are slipping.

This system includes an electronically
controlled transfer case with a high
capacity clutch. The system is interactive
with the road, continually monitoring and
adjusting torque delivery to the front and
rear wheels to optimize traction.

Note: Some noise may be heard as the
system shifts or engages; this is normal.
Note: 4X4 high mode is not intended for
use on dry pavement.

Note: The AdvanceTrac system has the
ability to take over control of the transfer
case clutch and disable it during driving
maneuvers when necessary.

You can move the control from 2H or 4H
at a stop or while driving. The information
display may display a message indicating
a 4X4 shift is in progress. Once the shift is
complete the message center will then
display the system mode selected.
Shifting to or from 4L (4X4 low)
Note: Some noise may be heard as the
system shifts or engages; this is normal.
154

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
4L (4X4 LOW)
Uses extra gearing to provide maximum
power to all four wheels at reduced
speeds. Intended only for off-road
applications such as deep sand, steep
grades, or pulling heavy objects. 4L (4x4
low) will not engage while the vehicle is
moving above 3 mph (5 km/h); this is
normal and should be no reason for
concern. Refer to Shifting to or from 4L
(4x4 low) for proper operation.

E166931

Shifting between system modes

2H (4X2)

Note: Momentarily releasing the accelerator
pedal while performing a shift will improve
engagement/disengagement times.

For general on-road driving. Sends power
to the rear wheels only and should be used
for street and highway driving. Provides
optimal smoothness and fuel economy at
high speeds.

Note: Do not perform this operation if the
rear wheels are slipping.
Note: Some noise may be heard as the
system shifts or engages; this is normal.

4A (4X4 AUTO)
Provides electronic control four-wheel
drive with power delivered to the front and
rear wheels, as required, for increased
traction. This is appropriate for all on-road
driving conditions, including as dry road
surfaces, but is especially useful on wet
pavement, snow, dirt, or gravel.

Note: 4X4 high mode is not intended for
use on dry pavement.
You can move the control from 2H to 4A
or 4H at a stop or while driving. The
information display may display a message
indicating a 4X4 shift is in progress. Once
the shift is complete the message center
will then display the system mode
selected.

4H (4X4 HIGH)
Used for extra traction such as in snow or
icy roads or in off road situations. This
mode is not intended for use on dry
pavement.

Shifting to or from 4L (4X4 low)
Note: Some noise may be heard as the
system shifts or engages; this is normal.

Note: Do not use 4H (4X4 HIGH) on dry,
hard surfaced roads. Doing so can produce
excessive noise and increased tire wear. 4H
(4X4 HIGH) is only intended for consistently
slippery or loose surfaces.

Note: 4x4 low mode is not intended for use
on dry pavement.
1.

Bring the vehicle to a speed of 3 mph
(5 km/h) or less.
2. Place the transmission in N (Neutral).
3. Move the 4WD control to the desired
position.

155

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
The differences that make your vehicle so
versatile also make it handle differently
than an ordinary passenger car.

The information display will display a
message indicating a 4X4 shift is in
progress. The information display will then
display the system mode selected. If any
of the above shift conditions are not met,
the shift will not occur and the information
display will display information guiding the
driver through the proper shifting
procedures.

Maintain steering wheel control at all
times, especially in rough terrain. Since
sudden changes in terrain can result in
abrupt steering wheel motion, make sure
you grip the steering wheel from the
outside. Do not grip the spokes.

Drive cautiously to avoid vehicle damage
from concealed objects such as rocks and
stumps.
You should either know the terrain or
examine maps of the area before driving.
Map out your route before driving in the
area. To maintain steering and braking
control of your vehicle, you must have all
four wheels on the ground and they must
be rolling, not sliding or spinning.

How Your Vehicle Differs From
Other Vehicles

Driving Off-Road With Truck and
Utility Vehicles

WARNING
Vehicles with a higher center of
gravity such as utility and four-wheel
drive vehicles handle differently than
vehicles with a lower center of gravity.
Utility and four-wheel drive vehicles are
not designed for cornering at speeds as
high as passenger cars any more than
low-slung sports cars are designed to
perform satisfactorily under off-road
conditions. Avoid sharp turns, excessive
speed and abrupt maneuvers in these
vehicles. Failure to drive cautiously could
result in an increased risk of loss of vehicle
control, vehicle rollover, personal injury and
death.

Note: On some models, the initial shift from
two-wheel drive to four-wheel drive while
the vehicle is moving can cause some
momentary clunk and ratcheting sounds.
This is the front drivetrain coming up to
speed and the automatic locking hubs
engaging and is not cause for concern.
Note: Your vehicle may be equipped with
a front air dam that can become damaged
(due to reduced ground clearance) when
taking your vehicle off-road. This air dam
can be taken off by removing two bolts.
Four-wheel drive vehicles are specially
equipped for driving on sand, snow, mud
and rough terrain and have operating
characteristics that are somewhat
different from conventional vehicles, both
on and off the road.

Truck and utility vehicles can differ from
some other vehicles. Your vehicle may be
higher to allow it to travel over rough
terrain without getting hung up or
damaging underbody components.

156

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
Power is supplied to all four wheels
through a transfer case. On Four-wheel
drive vehicles, the transfer case allows you
to select 4WD when necessary.
Information on transfer case operation and
shifting procedures can be found in this
chapter. Information on transfer case
maintenance can be found in the
Maintenance chapter. You should become
thoroughly familiar with this information
before you operate your vehicle.

It may be less risky to strike small objects,
such as freeway reflectors, with minor
damage to your vehicle rather than
attempt a sudden return to the road which
could cause your vehicle to slide sideways
out of control or roll over. Remember, your
safety and the safety of others should be
your primary concern.
Emergency Maneuvers
In an unavoidable emergency situation
where a sudden sharp turn must be made,
remember to avoid over-driving your
vehicle (i.e. turn the steering wheel only as
rapidly and as far as required to avoid the
emergency). Excessive steering can result
in loss of vehicle control. Apply smooth
pressure to the accelerator pedal or brake
pedal when changes in vehicle speed are
required. Avoid abrupt steering,
acceleration and braking. This could result
in an increased risk of vehicle roll over, loss
of vehicle control and personal injury. Use
all available road surface to bring your
vehicle to a safe direction of travel.

Four-wheel drive (when you select a 4WD
mode) uses all four wheels to power the
vehicle. This increases traction, enabling
you to drive over terrain and road
conditions that a conventional two-wheel
drive vehicle cannot.
Basic Operating Principles
•

•

Drive slower in strong crosswinds which
can affect the normal steering
characteristics of your vehicle.
When driving your vehicle on surfaces
made slippery by loose sand, water,
gravel, snow or ice proceed with care.
Do not use Four-wheel drive on dry,
hard surfaced roads. Doing so will
produce excessive noise, increase tire
wear and may damage drive
components. Four-wheel drive modes
are only intended for consistently
slippery or loose surfaces.

In the event of an emergency stop, avoid
skidding the tires and do not attempt any
sharp steering wheel movements.
If your vehicle goes from one type of
surface to another (i.e. from concrete to
gravel) there will be a change in the way
your vehicle responds to a maneuver (i.e.
steering, acceleration or braking).

If Your Vehicle leaves the Road

Sand

If your vehicle leaves the road, reduce your
vehicle speed and avoid severe braking.
When your vehicle speed has been reduced
ease your vehicle back onto the road. Do
not turn the steering wheel sharply while
returning your vehicle to the road.

When driving over sand, try to keep all four
wheels on the most solid area of the trail.
Avoid reducing the tire pressures but shift
to a lower gear and drive steadily through
the terrain. Apply the accelerator slowly
and avoid excessive wheel slip.

It may be safer to stay on the shoulder of
the road and slow down gradually before
returning to the road. You may lose control
if you do not slow down or if you turn the
steering wheel too sharply or abruptly.

When driving at slow speeds in deep sand
under high outside temperatures, use a low
gear when possible. Low gear operation
will maximize the engine and transmission
cooling capability.
157

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
Avoid driving at excessive speeds, this
causes vehicle momentum to work against
you and your vehicle could become stuck
to the point that assistance may be
required from another vehicle. Remember,
you may be able to back out the way you
came if you proceed with caution.

Driving on Hilly or Sloping Terrain
Although natural obstacles may make it
necessary to travel diagonally up or down
a hill or steep incline, you should always
try to drive straight up or straight down.
Note: Avoid turning on steep slopes or hills.
A danger lies in losing traction, slipping
sideways and possible vehicle roll over.
Whenever driving on a hill, determine
beforehand the route you will use. Do not
drive over the crest of a hill without seeing
what conditions are on the other side. Do
not drive in reverse over a hill without the
aid of an observer.

Mud and Water
Mud
Be cautious of sudden changes in vehicle
speed or direction when you are driving in
mud. Even four-wheel drive vehicles can
lose traction in slick mud. If your vehicle
does slide, steer in the direction of the slide
until you regain control of your vehicle.

When climbing a steep slope or hill, start
in a lower gear rather than downshifting to
a lower gear from a higher gear once the
ascent has started. This reduces strain on
the engine and the possibility of stalling.

After driving through mud, clean off residue
stuck to rotating driveshafts and tires.
Excess mud stuck on tires and rotating
driveshafts can cause an imbalance that
could damage drive components.

If your vehicle stalls, do not try to turn
around because this could cause vehicle
roll over. It is better to reverse back to a
safe location.

Water
If you must drive through high water, drive
slowly. Traction or brake capability may
be limited.

Apply just enough power to the wheels to
climb the hill. Too much power will cause
the tires to slip, spin or lose traction,
resulting in loss of vehicle control.

When driving through water, determine the
depth and avoid water higher than the
bottom of the hubs. If the ignition system
gets wet, your vehicle may stall.
Once through water, always try the brakes.
Wet brakes do not stop your vehicle as
effectively as dry brakes. Drying can be
improved by applying light pressure to the
brake pedal while moving slowly.
Note: Driving through deep water may
damage the transmission. If the front or rear
axle is submerged in water, the axle
lubricant and power transfer unit lubricant
should be checked and changed if
necessary.

E143949

158

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
Descend a hill in the same gear you would
use to climb up the hill to avoid excessive
brake application and brake overheating.
Do not descend in neutral. Disengage
overdrive or move the transmission
selector lever to a lower gear. When
descending a steep hill, avoid sudden hard
braking as you could lose control. The front
wheels have to be turning in order to steer
your vehicle.

Avoid sudden braking. Although a
four-wheel drive vehicle may accelerate
better than a two-wheel drive vehicle in
snow and ice, it will not stop any faster as
braking occurs at all four wheels. Do not
become overconfident as to road
conditions.
Make sure you allow sufficient distance
between you and other vehicles for
stopping. Drive slower than usual and
consider using one of the lower gears. In
emergency stopping situations, apply the
brake steadily. Do not pump the brake
pedal. See Hints on Driving With
Anti-Lock Brakes (page 163).

If your vehicle has anti-lock brakes, apply
the brakes steadily. Do not pump the
brakes.
Driving on Snow and Ice
WARNING

If Your Vehicle Gets Stuck In Mud or
Snow

If you are driving in slippery
conditions that require tire chains or
cables, then it is critical that you drive
cautiously. Keep speeds down, allow for
longer stopping distances and avoid
aggressive steering to reduce the chances
of a loss of vehicle control which can lead
to serious injury or death. If the rear end of
your vehicle slides while cornering, steer in
the direction of the slide until you regain
control of your vehicle.

WARNING
Do not spin the wheels at over 35
mph (56 km/h). The tires may fail
and injure a passenger or bystander.
If your vehicle gets stuck in mud or snow,
it may be rocked out by shifting between
forward and reverse gears, stopping
between shifts in a steady pattern. Press
lightly on the accelerator in each gear.

Note: Excessive tire slippage can cause
transmission damage.

Note: Do not rock your vehicle if the engine
is not at normal operating temperature,
damage to the transmission may occur.

Four-wheel drive vehicles have advantages
over two-wheel drive vehicles in snow and
ice but can skid like any other vehicle.
Should you start to slide while driving on
snowy or icy roads, turn the steering wheel
in the direction of the slide until you regain
control.

Note: Do not rock your vehicle for more
than a minute, damage to the transmission
and tires may occur or the engine may
overheat.
Parking

Avoid sudden applications of power and
quick changes of direction on snow and
ice. Apply the accelerator slowly and
steadily when starting from a full stop.

WARNINGS
If the parking brake is fully released,
but the brake warning lamp remains
illuminated, the brakes may not be
working properly. See your authorized
dealer.

159

F150 (TF6) , enUSA

Four-Wheel Drive (If Equipped)
WARNINGS
Always set the parking brake fully
and make sure the gearshift is
latched in P (Park). Turn the ignition
to the off position and remove the key
whenever you leave your vehicle.
On some Four-wheel drive vehicles, when
the transfer case is in the N (Neutral)
position, the engine and transmission are
disconnected from the rest of the driveline.
Therefore, the vehicle is free to roll even if
the automatic transmission is in P (Park)
or the manual transmission is in gear. Do
not leave the vehicle unattended with the
transfer case in the N (Neutral) position.
Always set the parking brake fully and turn
off the ignition when leaving the vehicle.
Maintenance and Modifications
The suspension and steering systems on
your vehicle have been designed and
tested to provide predictable performance
whether loaded or empty. For this reason,
we strongly recommend that you do not
make modifications such as adding or
removing parts (i.e. lift kits or stabilizer
bars) or by using replacement parts not
equivalent to the original factory
equipment.
We recommend that you use caution when
your vehicle has either a high load or device
(i.e. ladder or luggage racks). Any
modifications to your vehicle that raise the
center of gravity may cause your vehicle
to roll over when there is a loss of vehicle
control.
Failure to maintain your vehicle correctly
may void the warranty, increase your repair
cost, reduce vehicle performance and
operational capabilities and adversely
affect you and your passenger's safety. We
recommend you frequently inspect your
vehicle's chassis components when your
vehicle is subject to off road usage.

160

F150 (TF6) , enUSA

Rear Axle
•

LIMITED SLIP DIFFERENTIAL
(IF EQUIPPED)

This axle provides added traction on
slippery surfaces, particularly when one
wheel is on a poor traction surface. Under
normal conditions, the limited-slip axle
functions like a standard rear axle. The axle
may exhibit a slight noise or vibration
during tight turns with low vehicle speed.
This is normal behavior and indicates the
axle is working.

•

ELECTRONIC LOCKING
DIFFERENTIAL (IF EQUIPPED)
•
Note: The electronic locking differential is
for off-road use only and is not for use on
dry pavement. Using the electronic locking
differential on dry pavement will result in
increased tire wear, noise and vibration.

When you switch the system on, if you do
not meet the required conditions for
electronic locking differential activation,
the instrument cluster will display the
appropriate information guiding you
through the proper activation process.

The electronic locking differential is a
device housed in the rear axle that allows
both rear wheels to turn at the same
speed. The electronic locking differential
can provide additional traction should your
vehicle become stuck. You can activate
the differential electronically and shift it
on the fly within the differential operating
speed range. The differential is for use in
mud, rocks, sand, or any off-road condition
where you need maximum traction. It is
not for use on dry pavement.

Activating the Electronic Locking
Differential (If Equipped)
Note: Do not use electronic locking
differential on dry, hard surfaced roads.
Doing so will produce excessive noise,
vibration and increase tire wear.

The following conditions will affect the
electronic locking differential:
•

•

Note: If the electronic locking differential
has difficulty disengaging, release the
accelerator pedal and turn the steering
wheel in the opposite direction while rolling.

The electronic locking differential will
not engage if your vehicle speed is
above 20 mph (32 km/h) in 4x2, 4x4
Auto, or 4x4 High modes
The electronic locking differential will
not engage if your vehicle speed is
above or 56 mph (90 km/h) in 4X4
Low

161

F150 (TF6) , enUSA

The electronic locking differential will
not engage if you press your
accelerator pedal beyond 50% during
an engagement attempt
In 4x2, 4x4 Auto, and 4x4 High modes,
the electronic locking differential will
automatically disengage at speeds
above 25 mph (41 km/h) and will
automatically reengage at speeds
below 20 mph (32 km/h)
In 4L (4X4 low), the electronic locking
differential will automatically
disengage at speeds above 62 mph
(100 km/h) and will automatically
reengage at speeds below 56 mph (90
km/h)
The AdvanceTrac system has the
ability to take over control of the
electronic locking differential and
disable it during driving maneuvers
when necessary

Rear Axle
For 4WD vehicles

•
•

•

E166932

Pull the 4WD control knob toward you.
For 2WD vehicles

E163191

Turn the control to ON.
Once the indicator light
illuminates in the information
E163170
display, both rear wheel axle
shafts will be locked together providing
added traction.
If the indicator does not come on, or the
indicator turns off while driving, one of the
following has occurred:

162

F150 (TF6) , enUSA

The vehicle speed is too high.
The left and right rear wheel speed
difference is too high during an
engagement attempt.
The system has malfunctioned and is
accompanied by CHECK LOCKING
DIFFERENTIAL in the information
display. See your authorized Ford
dealer for assistance.

Brakes
Brake Assist

GENERAL INFORMATION

Brake assist detects when you brake
rapidly by measuring the rate at which you
press the brake pedal. It provides
maximum braking efficiency as long as you
press the pedal, and can reduce stopping
distances in critical situations.

Note: Occasional brake noise is normal. If
a metal-to-metal, continuous grinding or
continuous squeal sound is present, the
brake linings may be worn-out. Have the
system checked by an authorized dealer. If
your vehicle has continuous vibration or
shudder in the steering wheel while braking,
have it checked by an authorized dealer.

Anti-lock Brake System
This system helps you maintain steering
control during emergency stops by keeping
the brakes from locking.

Note: Brake dust may accumulate on the
wheels, even under normal driving
conditions. Some dust is inevitable as the
brakes wear and does not contribute to
brake noise. See Cleaning the Alloy
Wheels (page 264).

This lamp momentarily
illuminates when you turn the
ignition on. If the light does not
illuminate during start up, remains on or
flashes, the system may be disabled. Have
the system checked by an authorized
dealer.

See Warning Lamps and
Indicators (page 82).
E144522

Wet brakes result in reduced braking
efficiency. Gently press the brake pedal a
few times when driving from a car wash or
standing water to dry the brakes.

If the system is disabled, normal
braking is still effective. If the
E144522
brake warning lamp illuminates
when you release the parking brake, have
the system checked by an authorized
dealer.

Brake Over Accelerator
In the event the accelerator pedal
becomes stuck or entrapped, apply steady
and firm pressure to the brake pedal to
slow the vehicle and reduce engine power.
If you experience this condition, apply the
brakes and bring your vehicle to a safe
stop. Move the transmission selector lever
to position P, switch the engine off and
apply the parking brake. Inspect the
accelerator pedal for any interference. If
none are found and the condition persists,
have your vehicle towed to the nearest
authorized dealer.

HINTS ON DRIVING WITH
ANTI-LOCK BRAKES
Note: When the system is operating, the
brake pedal will pulse and may travel
further. Maintain pressure on the brake
pedal. You may also hear a noise from the
system. This is normal.
The anti-lock braking system will not
eliminate the risks when:
• you drive too closely to the vehicle in
front of you
• your vehicle is hydroplaning
• you take corners too fast
• the road surface is poor.

163

F150 (TF6) , enUSA

Brakes
PARKING BRAKE

WARNINGS
You must remain in your vehicle once
you have activated the system.

WARNING
Always set the parking brake fully
and make sure the transmission is
placed in park (P). Failure to set the
parking brake and engage park could result
in vehicle roll-away, property damage or
bodily injury. Turn the ignition to the lock
position and remove the key whenever you
leave your vehicle.

During all times, you are responsible
for controlling your vehicle,
supervising the system and
intervening, if required.

Apply the parking brake whenever your
vehicle is parked. Press the pedal
downward to set the parking brake. The
brake warning lamp in the instrument
cluster will illuminate and remains
illuminated until the parking brake is
released.

The system makes it easier to pull away
when your vehicle is on a slope without the
need to use the parking brake.

If the engine is revved excessively, or
if a malfunction is detected, the
system will be deactivated.

When the system is active, your vehicle will
remain stationary on the slope for two to
three seconds after you release the brake
pedal. This allows you time to move your
foot from the brake to the accelerator
pedal. The brakes are released
automatically once the engine has
developed sufficient drive to prevent your
vehicle from rolling down the slope. This
is an advantage when pulling away on a
slope, (for example from a car park ramp,
traffic lights or when reversing uphill into
a parking space).

To release, pull the brake release lever
located at the lower left side of the
instrument panel.
If you are parking your vehicle on a grade
or with a trailer, press and hold the brake
pedal down, then set the parking brake.
There may be a little vehicle movement as
the parking brake sets to hold the vehicle's
weight. This is normal and should be no
reason for concern. If needed, press and
hold the service brake pedal down, then
try reapplying the parking brake. Chock the
wheels if required. If the parking brake
cannot hold the weight of the vehicle, the
parking brake may need to be serviced or
the vehicle may be overloaded.

The system will activate automatically on
any slope that will cause significant vehicle
rollback.

Using Hill Start Assist
1.

Press the brake pedal to bring your
vehicle to a complete standstill. Keep
the brake pedal pressed.
2. If the sensors detect that your vehicle
is on a slope, the system will activate
automatically.
3. When you remove your foot from the
brake pedal, your vehicle will remain
on the slope without rolling away for
about two or three seconds. This hold
time will automatically be extended if
you are in the process of driving off.

HILL START ASSIST
WARNINGS
The system does not replace the
parking brake. When you leave your
vehicle, always apply the parking
brake and put the transmission in park (P).

164

F150 (TF6) , enUSA

Brakes
4. Drive off in the normal manner. The
brakes will release automatically.

165

F150 (TF6) , enUSA

Traction Control
System Indicator Lights and
Messages

PRINCIPLE OF OPERATION
The traction control system helps avoid
drive wheel spin and loss of traction.

WARNING
If a failure has been detected within
the traction control system, the
stability control light will illuminate
steadily. Verify that the traction control
system was not manually disabled using
the stability control button. If the stability
control light still illuminates steadily, have
the system serviced by an authorized
dealer immediately. Operating your vehicle
with traction control disabled could lead
to an increased risk of loss of vehicle
control, vehicle rollover, personal injury and
death.

If your vehicle begins to slide, the system
applies the brakes to individual wheels
and, when needed, reduces engine power
at the same time. If the wheels spin when
accelerating on slippery or loose surfaces,
the system reduces engine power in order
to increase traction.

USING TRACTION CONTROL
In certain situations (for example, stuck in
snow or mud), you can turn the traction
control off. This may be beneficial as this
allows the wheels to spin with full engine
power.

The stability control light
temporarily illuminates on
E138639
engine start-up and flashes
when a driving condition activates the
stability system.
The stability control off light
temporarily illuminates on
engine start-up and stays on
when you turn the traction control system
off or if a problem occurs in the stability
system.

E166706

Turn the traction control system off by
pressing the stability control button
located on the center of the instrument
panel.

166

F150 (TF6) , enUSA

Stability Control
The AdvanceTrac with Roll Stability
Control system helps you keep control of
your vehicle when on a slippery surface.
The electronic stability control portion of
the system helps avoid skids and lateral
slides and roll stability control helps avoid
a vehicle rollover. The traction control
system helps avoid drive wheel spin and
loss of traction. See Using Traction
Control (page 166).

PRINCIPLE OF OPERATION
WARNINGS
Vehicle modifications involving
braking system, aftermarket roof
racks, suspension, steering system,
tire construction and wheel and tire size
may change the handling characteristics
of your vehicle and may adversely affect
the performance of the AdvanceTrac
system. In addition, installing any stereo
loudspeakers may interfere with and
adversely affect the AdvanceTrac system.
Install any aftermarket stereo loudspeaker
as far as possible from the front center
console, the tunnel, and the front seats in
order to minimize the risk of interfering with
the AdvanceTrac sensors. Reducing the
effectiveness of the AdvanceTrac system
could lead to an increased risk of loss of
vehicle control, vehicle rollover, personal
injury and death.

B
B
A

Remember that even advanced
technology cannot defy the laws of
physics. It’s always possible to lose
control of a vehicle due to inappropriate
driver input for the conditions. Aggressive
driving on any road condition can cause
you to lose control of your vehicle
increasing the risk of personal injury or
property damage. Activation of the
AdvanceTrac system is an indication that
at least some of the tires have exceeded
their ability to grip the road; this could
reduce the operator’s ability to control the
vehicle potentially resulting in a loss of
vehicle control, vehicle rollover, personal
injury and death. If your AdvanceTrac
system activates, SLOW DOWN.

E72903

167

F150 (TF6) , enUSA

Vehicle without AdvanceTrac
with RSC skidding off its
intended route.

Vehicle with AdvanceTrac with
RSC maintaining control on a
slippery surface.

Stability Control
electronic stability control and roll stability
control portions of the system off below
35 mph (56 km/h). When the transmission
is in position R, they are disabled. You can
turn off the traction control portion of the
system independently. See Using
Traction Control (page 166).

USING STABILITY CONTROL
AdvanceTrac™ with Roll Stability
Control™ (RSC™)
The system automatically activates when
you start your engine. You can turn off the

AdvanceTrac with RSC Features

Button functions

Stability
control OFF
light

Roll stability
control

Electronic
stability
control

Traction
control system

Default at startup

Illuminated
during bulb
check

Enabled

Button pressed
momentarily

Illuminated
solid

Enabled

Disabled

Button pressed
and held for
more than 5
seconds at
vehicle speed
under 35 mph
(56 km/h)

Flashes then
illuminated

Disabled

Vehicle speed
exceeds 35 mph
(56 km/h) after
button is
pressed and
held for more
than 5 seconds

Illuminated
solid

Enabled

solid

168

F150 (TF6) , enUSA

Disabled

Stability Control
AdvanceTrac with RSC Features

Button pressed
again after
deactivation

Not illuminated

Enabled

Transfer case
switched to
4WD Low

Illuminated

Disabled

Locked
1

Traction control system could be enabled but with higher entry thresholds compared to
full system. Electronic stability control entry thresholds are higher compared to the full
system.
2

Lamp light starts blinking for four seconds after entering the press and hold state.

Control switch is not pressed. Stability control light turned on when 4WD Low Locked
transfer case mode selected.
4

Engine traction control and two-wheel spin brake traction control functions are disabled.
Single wheel spin traction control is always enabled.

169

F150 (TF6) , enUSA

Terrain Response (If Equipped)
PRINCIPLE OF OPERATION

USING HILL DESCENT
CONTROL

WARNINGS
Hill descent control cannot control
descent in all surface conditions and
circumstances, such as ice or
extremely steep grades. Hill descent
control is a driver assist system and cannot
substitute for good judgment by the driver.
Failure to do so may result in loss of vehicle
control, crash or serious injury.

Press and release the hill
descent button located on the
E163957
instrument panel. A light in the
cluster will illuminate and a
chime will sound when this feature is
activated.
To increase descent speed, press the
accelerator pedal until the desired speed
is reached. To decrease descent speed,
press the brake pedal until the desired
speed is reached.

Hill descent control does not provide
hill hold at zero miles per hour (0
kilometers per hour). When stopped,
the parking brake must be applied or the
vehicle must be placed in P (Park) or it
may roll away.

Whether accelerating or decelerating, once
the desired descent speed is reached,
remove your feet from the pedals and the
chosen vehicle speed will be maintained.

Hill descent control allows the driver to set
and maintain vehicle speed while
descending steep grades in various surface
conditions.

Note: Noise from the ABS pump motor may
be observed during hill descent control
operation. This is a normal characteristic of
the ABS and should be no reason for
concern.

Hill descent control can maintain vehicle
speeds on downhill grades between 2 mph
(3 km/h) and 12 mph (20 km/h). Above 20
mph (32 km/h), the system remains
armed, but descent speed cannot be set
or maintained.

Hill descent modes

Hill descent control requires a cooling
down interval after a period of sustained
use. The amount of time that the feature
can remain active before cooling varies
with conditions. The system will provide a
warning in the message center and a chime
will sound when the system is about to
disengage for cooling. At this time,
manually apply the brakes as needed to
maintain descent speed.

170

F150 (TF6) , enUSA

•

At speeds below 20 mph (32 km/h):
When the Hill Descent Control switch
is pressed and Hill Descent Control is
active, the Hill Descent Control telltale
will flash.

•

At speeds below 20 mph (32 km/h):
When the Hill Descent Control switch
is pressed and conditions are not
correct for hill descent activation, the
Hill Descent Control system will be
enabled, the Hill Descent Control
telltale will be solid and a message will
display in the information display.

Terrain Response (If Equipped)
•

At speeds above 20 mph (32 km/h):
When the Hill Descent Control switch
is pressed, the Hill Descent Control
system will be enabled, the telltale in
the cluster will not be illuminated and
a message will be displayed in the
information display.

Refer to the Information Displays for
additional Hill Descent Control messages.
See Information Messages (page 98).

171

F150 (TF6) , enUSA

Parking Aids
Note: If your vehicle is equipped with
MyKey™, it is possible to prevent turning
the sensing system off. See MyKey™ (page
53).

PARKING AID (IF EQUIPPED)
WARNINGS
To help avoid personal injury, please
read and understand the limitations
of the system as contained in this
section. Sensing is only an aid for some
(generally large and fixed) objects when
moving in reverse on a flat surface at
parking speeds. Traffic control systems,
inclement weather, air brakes, and external
motors and fans may also affect the
function of the sensing system; this may
include reduced performance or a false
activation.

Note: If your vehicle is equipped with a fully
integrated electronic trailer brake controller
(TBC) and a trailer with electric trailer
brakes is connected to your vehicle, the RSS
will be disabled. When the vehicle is shifted
into reverse, the information display will
remain in the Rear Park Aid Off selection.
For more information on the TBC, See
Trailer Sway Control (page 192).
The sensing system warns the driver of
obstacles within a certain range of the
bumper area. The system turns on
automatically whenever the ignition is
switched on.

To help avoid personal injury, always
use caution when in R (Reverse) and
when using the sensing system.

When receiving a detection warning, the
radio volume is reduced to a
predetermined level. After the warning
goes away, the radio volume returns to the
previous level.

This system is not designed to
prevent contact with small or moving
objects. The system is designed to
provide a warning to assist the driver in
detecting large stationary objects to avoid
damaging the vehicle. The system may not
detect smaller objects, particularly those
close to the ground.

Rear Sensing System
The rear sensors are only active when the
transmission is in R (Reverse). As the
vehicle moves closer to the obstacle, the
rate of the audible warning increases.
When the obstacle is fewer than 12 inches
(30 centimeters) away, the warning
sounds continuously. If a stationary or
receding object is detected farther than 12
inches (30 centimeters) from the side of
the vehicle, the tone sounds for only three
seconds. Once the system detects an
object approaching, the warning sounds
again.

Certain add-on devices such as large
trailer hitches, bike or surfboard racks
and any device that may block the
normal detection zone of the system, may
create false beeps.
Note: Keep the sensors, located on the
bumper or fascia, free from snow, ice and
large accumulations of dirt. If the sensors
are covered, the system’s accuracy can be
affected. Do not clean the sensors with
sharp objects.
Note: If your vehicle sustains damage to
the bumper or fascia, leaving it misaligned
or bent, the sensing zone may be altered
causing inaccurate measurement of
obstacles or false alarms.

172

F150 (TF6) , enUSA

Parking Aids
WARNINGS
Back up as slow as possible since
higher speeds might limit your
reaction time to stop the vehicle.
Use caution when using the rear
video camera and the liftgate is ajar.
If the liftgate is ajar, the camera will
be out of position and the video image may
be incorrect. All guidelines (if enabled)
have been removed when the liftgate is
ajar.

E130178

Use caution when turning camera
features on or off while in Reverse
(R). Make sure the vehicle is not
moving.

Coverage area of up to 6 feet
(1.8 meters) from the rear
bumper. There is decreased
coverage area at the outer
corners of the bumper.

The rear view camera system provides a
video image of the area behind your
vehicle.

The system detects certain objects while
the transmission is in R (Reverse):
• and moving toward a stationary object
at a speed of 3 mph (5 km/h) or less
• but not moving, and a moving object is
approaching the rear of the vehicle at
a speed of 3 mph (5 km/h) or less

During operation, lines appear in the
display that represent your vehicle’s path
and proximity to objects behind your
vehicle.

The system can be switched off through
the information display. If a fault is present
in the system, a warning message appears
in the information display and does not
allow the driver to switch the faulted
system on.

REAR VIEW CAMERA (IF EQUIPPED)
WARNINGS
The rear view camera system is a
reverse aid supplement device that
still requires the driver to use it in
conjunction with the interior and exterior
mirrors for maximum coverage.

E163192

The camera is located on the tailgate.

Using the Rear View Camera
System
The rear view camera system displays
what is behind your vehicle when you place
the transmission in Reverse (R).

Objects that are close to either
corner of the bumper or under the
bumper, might not be seen on the
screen due to the limited coverage of the
camera system.

173

F150 (TF6) , enUSA

Parking Aids
Note: The centerline is only available if
fixed guidelines are on.

The system uses two types of guides to
help you see what is behind your vehicle:
• Fixed guidelines: Show the actual path
your vehicle is moving in while reversing
in a straight line. This can be helpful
when backing into a parking space or
aligning your vehicle with another
object behind you.
• Centerline: Helps align the center of
your vehicle with an object (for
example, a trailer).

D
C
B

Note: If the image comes on while the
transmission is not in Reverse (R), have the
system inspected by your authorized dealer.

E163914

Note: When towing, the camera only sees
what you are towing behind your vehicle.
This might not provide adequate coverage
as it usually provides in normal operation
and you might not see some objects. In
some vehicles, the guidelines may disappear
once you engage the trailer tow connector.
The camera may not operate correctly
under the following conditions:
• Nighttime or dark areas if the reverse
lamps are not operating.
• Mud, water or debris obstructs the
camera's view. Clean the lens with a
soft, lint-free cloth and non-abrasive
cleaner.
• The camera is misaligned due to
damage to the rear of your vehicle.

Rear bumper

Fixed guideline: Green zone

Fixed guideline: Yellow zone

Fixed guideline: Red zone

Centerline

The fixed guidelines fade in and out
depending on the steering wheel position.
The active guidelines are not shown when
the steering wheel position is straight.
Always use caution while reversing.
Objects in the red zone are closest to your
vehicle and objects in the green zone are
farther away. Objects are getting closer to
your vehicle as they move from the green
zone to the yellow or red zones. Use the
side view mirrors and rear view mirror to
get better coverage on both sides and rear
of the vehicle.

To access any of the rear view camera
system settings, make the following
selections in the touch screen when the
transmission is not in Reverse (R):
• Menu > Vehicle > Camera Settings

Enhanced Park Aids
Note: Enhanced park aids is only available
when the transmission is in Reverse (R).

After changing a system setting, the touch
screen shows a preview of the selected
features.

Note: The reverse sensing system is not
effective at speeds above 3 mph (5 km/h)
and may not detect certain angular or
moving objects.

Guidelines and the Centerline
Note: Fixed guidelines are only available
when the transmission is in R (Reverse).

174

F150 (TF6) , enUSA

Parking Aids
The system uses red, yellow and green
highlights which appear on top of the video
image when an object is detected by the
reverse sensing system. The alert highlights
the closest object detected. The reverse
sensing alert can be disabled and if visual
park aid alert is enabled, highlighted areas
are still displayed.
Selectable settings for this feature are ON
and OFF.
Rear Camera Delay
When shifting the transmission out of
Reverse (R) and into any gear other than
Park (P), the camera image remains in the
display until your vehicle speed reaches 6
mph (10 km/h) or 10 seconds elapses. This
occurs when the rear camera delay feature
is on.
Selectable settings for this feature are ON
and OFF. The default setting for the rear
camera delay is OFF.

175

F150 (TF6) , enUSA

Cruise Control (If Equipped)
The indicator will appear in the
instrument cluster.

PRINCIPLE OF OPERATION
E71340

Cruise control lets you maintain a set
speed without keeping your foot on the
accelerator pedal. You can use cruise
control when your vehicle speed is greater
than 20 mph (30 km/h).

Setting a Speed
1. Accelerate to the desired speed.
2. Press and release SET+.
3. Take your foot off the accelerator
pedal.

USING CRUISE CONTROL

The indicator will change colors in the
instrument cluster.

WARNINGS
Do not use cruise control in heavy
traffic, on winding roads or when the
road surface is slippery. This could
result in loss of vehicle control, serious
injury or death.

Changing the Set Speed
Note: If you accelerate by pressing the
accelerator pedal, the set speed will not
change. When you release the accelerator
pedal, you will return to the speed that you
previously set.

When you are going downhill, your
vehicle speed may increase above
the set speed. The system will not
apply the brakes. Change down a gear to
assist the system in maintaining the set
speed. Failure to do so could result in loss
of vehicle control, serious injury or death.

•

Note: Cruise control will disengage if the
vehicle speed decreases more than 10 mph
(16 km/h) below your set speed while
driving uphill.

•

Press and hold SET+ or SET-. Release
the control when you reach the desired
speed.
Press and release SET+ or SET-. The
set speed will change in approximately
1 mph (2 km/h) increments.
Press the accelerator or brake pedal
until you reach the desired speed. Press
and release SET+.

Canceling the Set Speed
Press CNCL or tap the brake pedal. You
will not erase the set speed.
Resuming the Set Speed
Press and release RSM.
E166638

Switching Cruise Control Off

The cruise controls are located on the
steering wheel.

Note: You will erase the set speed if you
switch the system off.

Switching Cruise Control On

Press and release OFF or switch the
ignition off.

Press and release ON.

176

F150 (TF6) , enUSA

Driving Aids
system. If this should occur, you will neither
lose the ability to steer the vehicle
manually nor will it cause permanent
damage. Typical steering and driving
maneuvers will allow the system to cool
and steering assist will return to normal.

STEERING
Electric Power Steering (3.7L, 5.0L
and 3.5L EcoBoost™ engines) (If
Equipped)

WARNINGS
The electric power steering system
has diagnostic checks that
continuously monitor the system to
ensure proper operation. When a system
error is detected a steering message will
appear in the information display.

Hydraulic Steering (6.2L engine)
(If Equipped)

To help prevent damage to the power
steering system, never hold the steering
wheel at its furthest turning points (until
it stops) for more than a few seconds
when the engine is running. If the power
steering system breaks down (or if the
engine is turned off), you can steer the
vehicle manually, but it takes more effort.

The electric power steering system
has diagnostic checks that
continuously monitor the system to
ensure proper operation of the electronic
system. When an electronic error is
detected, a message will be displayed in
the information display. If this happens,
stop the vehicle in a safe place, and turn
off the engine. After at least 10 seconds,
reset the system by restarting the engine,
and watch the information display for a
steering message. If a steering message
returns, or returns while driving, take the
vehicle to your dealer to have it checked.

•

Obtain immediate service if a system
error is detected. You may not notice
any difference in the feel of your
steering, but a serious condition may exist.
Failure to do so may result in loss of
steering control.

•

•
Your vehicle is equipped with an electric
power-assisted steering system. There is
no fluid reservoir to check or fill.

If the power steering system breaks down
(or if the engine is turned off), you can
steer the vehicle manually, but it takes
more effort.

If your vehicle loses electrical power while
you are driving (or if the ignition is turned
off), you can steer the vehicle manually,
but it takes more effort. Extreme
continuous steering may increase the effort
it takes for you to steer. This occurs to
prevent internal overheating and
permanent damage to your steering

177

F150 (TF6) , enUSA

Never hold the steering wheel at its
furthest turning points (until it stops)
for more than three to five seconds
when the engine is running.
Do not operate the vehicle with a low
power steering pump fluid level (below
the MIN mark on the reservoir).
Some noise is normal during operation.
If excessive, check for low power
steering pump fluid level before
seeking service by your dealer.
Heavy or uneven efforts may be caused
by low power steering fluid. Check for
low power steering pump fluid level
before seeking service by your dealer.
Do not fill the power steering pump
reservoir above the MAX mark on the
reservoir, as this may result in leaks
from the reservoir.

Driving Aids
Steering Tips
If the steering wanders or pulls, check for:
• an improperly inflated tire
• uneven tire wear
• loose or worn suspension components
• loose or worn steering components
• improper vehicle alignment
A high crown in the road or high crosswinds
may also make the steering seem to
wander or pull.

178

F150 (TF6) , enUSA

Load Carrying
the following terms for
determining your vehicle’s weight
ratings, with or without a trailer,
from the vehicle’s Tire Label or
Safety Compliance Certification
Label:
Base Curb Weight - is the weight
of the vehicle including a full tank
of fuel and all standard
equipment. It does not include
passengers, cargo, or optional
equipment.
Vehicle Curb Weight - is the
weight of your new vehicle when
you picked it up from your
authorized dealer plus any
aftermarket equipment.

LOAD LIMIT
Vehicle Loading - with and
without a Trailer
This section will guide you in the
proper loading of your vehicle,
trailer or both, to keep your loaded
vehicle weight within its design
rating capability, with or without
a trailer. Properly loading your
vehicle will provide maximum
return of vehicle design
performance. Before loading your
vehicle, familiarize yourself with

PAYLOAD

E143816

payload. The payload listed on the
Tire Label is the maximum
payload for the vehicle as built by
the assembly plant. If you install
any aftermarket or
authorized-dealer installed
equipment on the vehicle, you
must subtract the weight of the
equipment from the payload listed
on the Tire Label in order to
determine the new payload.

Payload - is the combined weight
of cargo and passengers that the
vehicle is carrying. The maximum
payload for your vehicle can be
found on the Tire Label on the
B-Pillar or the edge of the driver
door (vehicles exported outside
the US and Canada may not have
a Tire Label). Look for “THE
COMBINED WEIGHT OF
OCCUPANTS AND CARGO
SHOULD NEVER EXCEED XXX
kg OR XXX lb.” for maximum
179

F150 (TF6) , enUSA

Load Carrying
WARNING
The appropriate loading
capacity of your vehicle can
be limited either by volume
capacity (how much space is
available) or by payload capacity
(how much weight the vehicle
should carry). Once you have
reached the maximum payload of
your vehicle, do not add more
cargo, even if there is space
available. Overloading or
improperly loading your vehicle
can contribute to loss of vehicle
control and vehicle rollover.
Example only:

E142516

180

F150 (TF6) , enUSA

Load Carrying

E142517

CARGO

E143817

GAWR (Gross Axle Weight
Rating) - is the maximum
allowable weight that can be
carried by a single axle (front or
rear). These numbers are shown
on the Safety Compliance
Certification Label. The label shall
be affixed to either the door hinge
pillar, door-latch post, or the door
edge that meets the door-latch
post, next to the driver's seating
position. The total load on each
axle must never exceed its
Gross Axle Weight Rating.

Cargo Weight - includes all
weight added to the Base Curb
Weight, including cargo and
optional equipment. When towing,
trailer tongue load or king pin
weight is also part of cargo weight.
GAW (Gross Axle Weight) - is
the total weight placed on each
axle (front and rear) including
vehicle curb weight and all
payload.

181

F150 (TF6) , enUSA

Load Carrying
Note: For trailer towing
information refer to the RV and
Trailer Towing Guide available at
an authorized dealer.

GVW

E143818

Safety Compliance Certification
Label. The label shall be affixed
to either the door hinge pillar,
door-latch post, or the door edge
that meets the door-latch post,
next to the driver's seating
position. The Gross Vehicle
Weight must never exceed the
Gross Vehicle Weight Rating.

GVW (Gross Vehicle Weight) is the Vehicle Curb Weight, plus
cargo, plus passengers.
GVWR (Gross Vehicle Weight
Rating) - is the maximum
allowable weight of the fully
loaded vehicle (including all
options, equipment, passengers
and cargo). It is shown on the
Example only:

E142523

182

F150 (TF6) , enUSA

Load Carrying

E142524

WARNING
Exceeding the Safety
Compliance Certification
Label vehicle weight rating limits
could result in substandard
vehicle handling or performance,
engine, transmission and/or
structural damage, serious
damage to the vehicle, loss of
control and personal injury.

GCW

GVW

E143819

GCWR (Gross Combined
Weight Rating) - is the maximum
allowable weight of the vehicle
and the loaded trailer, including
all cargo and passengers, that the
vehicle can handle without risking
damage. (Important: The towing
vehicle’s braking system is rated

GCW (Gross Combined Weight)
- is the Gross Vehicle Weight plus
the weight of the fully loaded
trailer.

183

F150 (TF6) , enUSA

Load Carrying
Examples: For a 5000 pound
(2268 kilogram) conventional
trailer, multiply 5000 by 0.10 and
0.15 to obtain a proper tongue
load range of 500 to 750 pounds
(227 to 340 kilograms). For an
11500 pound (5216 kilogram) fifth
wheel trailer, multiply by 0.15 and
0.25 to obtain a proper king pin
load range of 1725 to 2875 pounds
(782 to 1304 kilograms).

for operation at Gross Vehicle
Weight Rating, not at Gross
Combined Weight Rating.)
Separate functional brakes should
be used for safe control of towed
vehicles and for trailers where the
Gross Combined Weight of the
towing vehicle plus the trailer
exceed the Gross Vehicle Weight
Rating of the towing vehicle. The
Gross Combined Weight must
never exceed the Gross
Combined Weight Rating.
Maximum Loaded Trailer
Weight - is the highest possible
weight of a fully loaded trailer the
vehicle can tow. It assumes a
vehicle with mandatory options,
driver and front passenger weight
(150 pounds [68 kilograms]
each), no cargo weight (internal
or external) and a tongue load of
10–15% (conventional trailer) or
king pin weight of 15–25% (fifth
wheel trailer). Consult an
authorized dealer (or the RV and
Trailer Towing Guide available at
an authorized dealer) for more
detailed information.
Tongue Load or Fifth Wheel
King Pin Weight - refers to the
amount of the weight that a trailer
pushes down on a trailer hitch.

WARNINGS
Do not exceed the GVWR or
the GAWR specified on the
Safety Compliance Certification
Label.
Do not use replacement tires
with lower load carrying
capacities than the original tires
because they may lower the
vehicle’s GVWR and GAWR
limitations. Replacement tires
with a higher limit than the original
tires do not increase the GVWR
and GAWR limitations.
Exceeding any vehicle weight
rating limitation could result
in serious damage to the vehicle
and/or personal injury.
Steps for determining the
correct load limit:
1. Locate the statement "The
combined weight of occupants
and cargo should never exceed
XXX kg or XXX lb." on your
vehicle’s placard.

184

F150 (TF6) , enUSA

Load Carrying
2. Determine the combined
weight of the driver and
passengers that will be riding
in your vehicle.
3. Subtract the combined weight
of the driver and passengers
from XXX kg or XXX lb.
4. The resulting figure equals the
available amount of cargo and
luggage load capacity. For
example, if the “XXX” amount
equals 1,400 lb. and there will
be five 150 lb. passengers in
your vehicle, the amount of
available cargo and luggage
load capacity is 650 lb.
(1400-750 (5 x 150) = 650 lb.)
5. Determine the combined
weight of luggage and cargo
being loaded on the vehicle.
That weight may not safely
exceed the available cargo and
luggage load capacity
calculated in Step 4.
6. If your vehicle will be towing a
trailer, load from your trailer
will be transferred to your
vehicle. Consult this manual to
determine how this reduces the
available cargo and luggage
load capacity of your vehicle.
The following gives you a few
examples on how to calculate the
available amount of cargo and
luggage load capacity:

*Suppose your vehicle has a
1400-pound (635-kilogram) cargo
and luggage capacity. You decide
to go golfing. Is there enough load
capacity to carry you, four of your
friends and all the golf bags? You
and four friends average 220
pounds (99 kilograms) each and
the golf bags weigh approximately
30 pounds (13.5 kilograms) each.
The calculation would be: 1400 (5 x 220) - (5 x 30) = 1400 - 1100
- 150 = 150 pounds. Yes, you have
enough load capacity in your
vehicle to transport four friends
and your golf bags. In metric units,
the calculation would be: 635
kilograms - (5 x 99 kilograms) (5 x 13.5 kilograms) = 635 - 495 67.5 = 72.5 kilograms.
*Suppose your vehicle has a
1400-pound (635-kilogram) cargo
and luggage capacity. You and
one of your friends decide to pick
up cement from the local home
improvement store to finish that
patio you have been planning for
the past two years. Measuring the
inside of the vehicle with the rear
seat folded down, you have room
for twelve 100-pound
(45-kilogram) bags of cement. Do
you have enough load capacity to
transport the cement to your
home? If you and your friend each
weigh 220 pounds (99 kilograms),
the calculation would be: 1400 (2 x 220) - (12 x 100) = 1400 - 440
- 1200 = - 240 pounds. No, you do
not have enough cargo capacity
to carry that much weight. In
metric units, the calculation would
185

F150 (TF6) , enUSA

Load Carrying
be: 635 kilograms - (2 x 99
kilograms) - (12 x 45 kilograms) =
635 - 198 - 540 = -103 kilograms.
You will need to reduce the load
weight by at least 240 pounds
(104 kilograms). If you remove
three 100-pound (45-kilogram)
cement bags, then the load
calculation would be:1400 - (2 x
220) - (9 x 100) = 1400 - 440 900 = 60 pounds. Now you have
the load capacity to transport the
cement and your friend home. In
metric units, the calculation would
be: 635 kilograms - (2 x 99
kilograms) - (9 x 45 kilograms) =
635 - 198 - 405 = 32 kilograms.
The above calculations also
assume that the loads are
positioned in your vehicle in a
manner that does not overload
the Front or the Rear Gross Axle
Weight Rating specified for your
vehicle on the Safety Compliance
Certification Label. The label shall
be affixed to either the door hinge
pillar, door-latch post, or the door
edge that meets the door-latch
post, next to the driver's seating
position.

Special Loading Instructions
for Owners of Pick-up Trucks
and Utility-type Vehicles
WARNING
Loaded vehicles may handle
differently than unloaded
vehicles. Extra precautions, such
as slower speeds and increased
stopping distance, should be
taken when driving a heavily
loaded vehicle.
Your vehicle can haul more cargo
and people than most passenger
cars. Depending upon the type
and placement of the load,
hauling cargo and people may
raise the center of gravity of the
vehicle.
TAILGATE
Tailgate Lock (If Equipped)
The tailgate lock can help prevent theft of
the tailgate.

E163087

Insert the ignition key into the tailgate lock.
Turn it to the right to lock the tailgate. Turn
it to the left to unlock the tailgate.

186

F150 (TF6) , enUSA

Load Carrying
Tailgate Removal
WARNING
Always properly secure cargo to
prevent shifting cargo or cargo falling
from vehicle, which could result in
compromised vehicle stability and serious
personal injury to vehicle occupants or
others.
You can remove the tailgate for more
loading room.

E163092

5. Use a screwdriver to gently pry the
spring clip on each connector past the
head of the support screw. Disconnect
the cable.
6. Disconnect the other cable.
7. Lift the tailgate to a 45-degree angle
from horizontal.
8. Lift the right side off its hinge.
9. Lift the tailgate to an 80-degree angle
from horizontal.
10. Remove the tailgate from the left side
hinge by sliding it to the right.

Note: Skip to Step 4 if your vehicle does
not have a rearview camera.

Reverse the steps to reinstall the tailgate.

E163090

Locate and disconnect the rearview
camera in-line connector. It is under
the pickup box on the right-hand side
of the vehicle near the spare tire.
2. There is a protective cap in the glove
box. Install it on the in-line connector
that remains under the pickup box.
3. Partially lower the tailgate. Carefully
feed the tailgate harness up through
the gap between the pickup box and
the bumper and place it out of the way
under the pickup box.
4. Lower the tailgate.

Tailgate Step (If Equipped)
Use the step to make entering the truck
bed easier.
To reduce the risk of falling:
• Only operate the step when your
vehicle is on a level surface.
• Only operate the step in areas with
sufficient lighting.
• Always open the step panel to widen
the step.
• Always use the grab handle when
climbing on the step.
• Do not use the step with bare feet.
• Make sure the step is clean before use.
• Keep the step load, you plus the load,
below 350 pounds (159 kilograms).
187

F150 (TF6) , enUSA

Load Carrying
Replace the slip resistance tape or grab
handle molding if it appears worn or
damaged.

Opening the Step
Note: Make sure to close and fully latch the
step before moving your vehicle. Never drive
with the step or grab handle open.

Closing the Step

1. Lower the tailgate.
2. Pull the yellow lever on the grab handle
to the unlock position.

Close the step panel then lift and fully
close the step into the tailgate.
2. Move the yellow lever on the grab
handle to the unlock position and lower
the handle.

Box Side Step (If Equipped)
Use the step for easier access to the trunk
bed.
Note: Do not drive with the step deployed.
Note: Do not exceed 500 pounds (227
kilograms) on the step. This includes you
plus cargo.

E163093

Note: Do not use the steps to lift the
vehicle. Only use proper jacking points.

3. Raise the handle upright until you feel
it latch and see the lever in the lock
position. You only need to use the lever
when releasing the grab handle.

Note: The steps may operate more slowly
in cool temperatures.
Note: The step mechanism may trap debris
such as mud, dirt, snow, ice and salt. This
may prevent the step from deploying
automatically when you press the button.
If this happens, make sure that you press
the button down and carefully pull out the
step manually. Wash off the debris with a
high-pressure car wash wand and stow the
step.

E163094

4. Rotate the center molding to unlatch
the step. Pull it toward you to extend
it.
5. Open the step panel to widen the step.
Note: Do not tow with the step or grab
handle.

188

F150 (TF6) , enUSA

Load Carrying
Note: Do not keep the bed extender in the
tailgate mode when you are not using it for
restraining cargo. Always keep the bed
extender in the grocery mode or the stowed
position with the tailgate closed.

Deploying the Step

Tailgate Mode

E167268

Push down on the button with your foot.
The step will automatically extend from
the stowed position.
Stowing the Step

E163095

Pull the locking pin toward the center
of your vehicle.

E167269

Push the step under the truck with your
foot until it fully latches. Do not push on
the button while stowing the step.

E163096

2. Open the latches to release the panels.

Bed Extender (If Equipped)
Note: Do not use the bed extender when
driving off road.
Note: Make sure to engage the locking pins
and knobs fully before driving your vehicle.
Note: Make sure to secure all cargo.
Note: Do not exceed 150 pounds (68
kilograms) on the tailgate when your vehicle
is moving.

189

F150 (TF6) , enUSA

Load Carrying
5. Make sure to insert the latch rod into
the tailgate hole. Make sure to engage
both sides of the locking pins into their
holes in the pick-up box.
Reverse the steps to store the bed
extender.
Grocery Mode

E163097

3. Rotate the panels toward the tailgate.
Repeat Steps 1-3 on the other side of
your vehicle.

E163100

Follow Steps 1-4 of the tailgate mode
instructions by rotating the panels away
from the tailgate. Close the tailgate.

E163098

4. Connect the two panels. Rotate both
knobs one-quarter turn clockwise to
secure the panels.

E163099

190

F150 (TF6) , enUSA

Towing
TOWING A TRAILER

Load Placement

WARNINGS
Do not exceed the GVWR or
the GAWR specified on the
certification label.
Towing trailers beyond the
maximum recommended
gross trailer weight exceeds the
limit of the vehicle and could
result in engine damage,
transmission damage, structural
damage, loss of vehicle control,
vehicle rollover and personal
injury.

To help minimize how trailer
movement affects your vehicle
when driving:
• Load the heaviest items closest
to the trailer floor.
• Load the heaviest items
centered between the left and
right side trailer tires.
• Load the heaviest items above
the trailer axles or just slightly
forward toward the trailer
tongue. Do not allow the final
trailer tongue weight to go
above or below 10-15% of the
loaded trailer weight.
• Select a tow bar with the
correct rise or drop. When both
the loaded vehicle and trailer
are connected, the trailer frame
should be level, or slightly
angled down toward your
vehicle, when viewed from the
side.
When driving with a trailer or
payload, a slight takeoff vibration
or shudder may be present due to
the increased payload weight.
Additional information regarding
proper trailer loading and setting
your vehicle up for towing is
located in another chapter of this
manual. See Load Limit (page
179). You can also find the
information in the RV & Trailer
Towing Guide, available at an
authorized dealer.

Your vehicle may have electrical
items, such as fuses or relays,
related to towing. See the Fuses
chapter.
Your vehicle's load capacity
designation is by weight, not by
volume, so you cannot necessarily
use all available space when
loading a vehicle.
Towing a trailer places an extra
load on your vehicle's engine,
transmission, axle, brakes, tires
and suspension. Inspect these
components periodically during,
and after, any towing operation.

191

F150 (TF6) , enUSA

Towing
Note: Do not exceed a trailer
weight of 5000 pounds (2268
kilograms) if your vehicle is not
equipped with a Heavy Duty Trailer
Towing Package.
Note: Make sure to take into
consideration trailer frontal area.
Vehicles not equipped with the
Trailer Tow Package or the Heavy
Duty Payload Package
should not
2
2
exceed 36 feet lb (3.35 meters )
trailer frontal area. Vehicles
equipped with the Trailer Tow
Package or the Heavy Duty Payload
Package
should not2 exceed 60
2
feet lb (5.6 meters ) trailer frontal
area.
Note: Exceeding this limitation
may significantly reduce the
performance of your towing
vehicle. Selecting a trailer with a
low aerodynamic drag and rounded
front design helps optimize
performance and fuel economy.
Note: For high altitude operation,
reduce the gross combined weight
by 2% per 1000 feet (300 meters)
starting at the 1000 foot (300
meter) elevation point.
Note: Certain states require
electric trailer brakes for trailers
over a specified weight. Be sure to
check state regulations for this
specified weight. The maximum
trailer weights listed may be limited
to this specified weight, as your
vehicle's electrical system may not
include the wiring connector
needed to use electric trailer
brakes.

TRAILER SWAY CONTROL (IF
EQUIPPED)

WARNING
Turning off trailer sway control
increases the risk of loss of vehicle
control, serious injury or death. Ford
does not recommend disabling this feature
except in situations where speed reduction
may be detrimental (such as hill climbing),
the driver has significant trailer towing
experience, and can control trailer sway
and maintain safe operation.
Note: This feature does not prevent trailer
sway, but reduces it once it begins.
Note: This feature cannot stop all trailers
from swaying.
Note: In some cases, if vehicle speed is too
high, the system may activate multiple
times, gradually reducing vehicle speed.
This feature applies your vehicle brakes at
individual wheels and, if necessary, reduces
engine power. If the trailer begins to sway,
the stability control light flashes and the
message TRAILER SWAY REDUCE
SPEED appears in the information display.
The first thing to do is slow your vehicle
down, then pull safely to the side of the
road and check for proper tongue load and
trailer load distribution. See Load
Carrying (page 179).

RECOMMENDED TOWING
WEIGHTS
Note: Do not exceed a trailer
weight of 5000 pounds (2268
kilograms) when towing with, or
by, bumper only.

192

F150 (TF6) , enUSA

Towing
Your vehicle may tow a trailer
provided the maximum trailer
weight is less than or equal to the

maximum trailer weight listed for
your vehicle configuration on the
following chart.

Regular cab
Driveline

Wheelbase
lb (inches)

Axle ratio

Maximum
GCWR

4.10

13300 lb
(6033 kg)

3.55

10400 lb
(4717 kg)

3.73

11500 lb
(5216 kg)

3.31

12900 lb
(5851 kg)

3.55

13300 lb
(6033 kg)

3.5L

4.10

13300 lb
(6033 kg)

3.7L

3.73

11500 lb
(5216 kg)

3.55

12900 lb
(5851 kg)

3.73

13300 lb
(6033 kg)

3.15

14000 lb
(6350 kg)

3.31

14900 lb
(6759 kg)

3.55

15000 lb
(6804 kg)

Engine
*

3.5L

Two-wheel
drive

3.7L
126

5.0L

Four-wheel
drive

126
5.0L

Two-wheel
drive

145

3.5L

193

F150 (TF6) , enUSA

Towing
Regular cab
Driveline

Wheelbase
lb (inches)

Axle ratio

Maximum
GCWR

3.73

16600 lb
(7530 kg)

3.55

10600 lb
(4808 kg)

3.73

11700 lb
(5307 kg)

3.55

13500 lb
(6123 kg)

3.73

14900 lb
(6759 kg)

3.73

15300 lb
(6940 kg)

3.31

15100 lb
(6849 kg)

3.55, 3.73

15200 lb
(6895 kg)

3.5L

3.73

16900 lb
(7666 kg)

3.7L

3.73

11700 lb
(5307 kg)

3.55

13500 lb
(6123 kg)

3.73

15100 lb
(6849 kg)

3.73

15300 lb
(6940 kg)

Engine
**

3.5L

3.7L

5.0L

3.5L

Four-wheel
drive

145

5.0L

5.0L
*

Tremor Package.

Heavy Duty Payload Package.

194

F150 (TF6) , enUSA

Towing

SuperCab
Driveline

Wheelbase
(inches)

Engine

Axle ratio

Maximum
GCWR

Four-wheel
drive

133

6.2L

4.10

12500 lb
(5670 kg)

3.15

14000 lb
(6350 kg)

3.31

14900 lb
(6759 kg)

3.55

15200 lb
(6895 kg)

3.5L

3.73

16900 lb
(7666 kg)

3.7L

3.73

11700 lb
(5307 kg)

3.31

13500 lb
(6123 kg)

3.55

14900 lb
(6759 kg)

6.2L

3.55

15500 lb
(7031 kg)

3.73

17000 lb
(7711 kg)

3.31

15100 lb
(6849 kg)

3.55, 3.73

15400 lb
(6985 kg)

3.5L

3.73, 4.10

17100 lb
(7756 kg)

3.7L

3.73

11700 lb
(5307 kg)

3.5L

Two-wheel
drive

145

5.0

6.2L

3.5L
Four-wheel
drive

145
2

195

F150 (TF6) , enUSA

Towing
SuperCab
Driveline

Wheelbase
(inches)

Axle ratio

Maximum
GCWR

3.55

13500 lb
(6123 kg)

3.73

15100 lb
(6849 kg)

6.2L

3.55

15600 lb
(7076 kg)

3.73

17100 lb
(7756 kg)

3.15

14000 lb
(6350 kg)

3.31

14900 lb
(6759 kg)

3.55

15200 lb
(6895 kg)

3.73

17000 lb
(7711 kg)

3.73

17000 lb
(7711 kg)

3.31

13500 lb
(6123 kg)

3.55

14900 lb
(6759 kg)

3.73

15300 lb
(6940 kg)

3.31

15100 lb
(6849 kg)

3.55, 3.73

15400 lb
(6985 kg)

Engine

5.0L

6.2L

3.5L

Two-wheel
drive

3.5L
163
3.5L

5.0L

Four-wheel
drive

163

3.5L

196

F150 (TF6) , enUSA

Towing
SuperCab
Driveline

Wheelbase
(inches)

Axle ratio

Maximum
GCWR

3.73, 4.10

17100 lb
(7756 kg)

3.73

17100 lb
(7756 kg)

3.55

13500 lb
(6123 kg)

3.73

15100 lb
(6849 kg)

3.73

15300 lb
(6940 kg)

Axle ratio

Maximum
GCWR

3.55, 3.73

13300 lb
(6033 kg)

3.15

14000 lb
(6350 kg)

3.31

14900 lb
(6759 kg)

3.55

15300 lb
(6940 kg)

3.73

16900 lb
(7666 kg)

Engine
3.5L
3.5L

5.0L

5.0L
1

SVT Raptor.

MAX Trailer Tow Package.

Heavy Duty Payload Package.

SuperCrew
Driveline

Wheelbase
(inches)

Engine
1

3.5L

Two-wheel
drive

145

3.5L

197

F150 (TF6) , enUSA

Towing
SuperCrew
Driveline

Wheelbase
(inches)

Engine

Axle ratio

Maximum
GCWR

3.7L

3.73

11700 lb
(5307 kg)

3.31, 3.55

13500 lb
(6123 kg)

3.73

14900 lb
(6759 kg)

6.2L

3.73

13500 lb
(6123 kg)

6.2L

3.55

15600 lb
(7076 kg)

3.73

17100 lb
(7756 kg)

3.55, 3.73

13400 lb
(6078 kg)

3.31

15100 lb
(6849 kg)

3.55, 3.73

15500 lb
(7031 kg)

3.73, 4.10

17100 lb
(7756 kg)

3.55

13500 lb
(6123 kg)

3.73

15100 lb
(6849 kg)

3.73

13500 lb
(6123 kg)

4.10

14700 lb
(6668 kg)

5.0
Two-wheel
drive

145

6.2L

3.5L

Four-wheel
drive

3.5L
145

5.0L

6.2L
6.2L

198

F150 (TF6) , enUSA

Towing
SuperCrew
Driveline

Wheelbase
(inches)

Engine

Axle ratio

Maximum
GCWR

6.2L

3.55

15600 lb
(7076 kg)

3.73

17100 lb
(7756 kg)

3.15

14000 lb
(6350 kg)

3.31

14900 lb
(6759 kg)

3.55

15300 lb
(6940 kg)

3.73

17000 lb
(7711 kg)

3.73

17100 lb
(7756 kg)

3.31, 3.55

13500 lb
(6123 kg)

3.73

14900 lb
(6759 kg)

5.0L

3.73

15300 lb
(6940 kg)

6.2L

3.55

15600 lb
(7076 kg)

3.73

17100 lb
(7756 kg)

3.31

15100 lb
(6849 kg)

3.55, 3.73

15500 lb
(7031 kg)

6.2L

3.5L

Two-wheel
drive

3.5L
157

5.0L

6.2L

Four-wheel
drive

157

3.5L

199

F150 (TF6) , enUSA

Towing
SuperCrew
Driveline

Wheelbase
(inches)

Axle ratio

Maximum
GCWR

3.73, 4.10

17100 lb
(7756 kg)

3.73

17100 lb
(7756 kg)

3.55

13500 lb
(6123 kg)

3.73

15100 lb
(6849 kg)

5.0L

3.73

15300 lb
(6940 kg)

6.2L

3.55

15600 lb
(7076 kg)

3.73

17100 lb
(7756 kg)

Engine
3.5L
3.5L

5.0L

6.2L
1

Limited.

MAX Trailer Tow Package.

SVT Raptor.

Heavy Duty Payload Package.
•
•

Calculating the Maximum
Loaded Trailer Weight for Your
Vehicle
1. Start with the gross combined
weight rating for your vehicle
model and axle ratio. See the
previous charts.
2. Subtract all of the following
that apply to your vehicle:

•
•
•
•

200

F150 (TF6) , enUSA

Vehicle curb weight
Hitch hardware weight, such as
a draw bar, ball, locks or weight
distributing hardware
Driver weight
Passenger(s) weight
Payload, cargo and luggage
weight
Aftermarket equipment weight.

Towing
Trailer Towing Connector

This equals the maximum loaded
trailer weight for this combination.
Note: The trailer tongue load is
considered part of the payload for
your vehicle. Reduce the total
payload by the final trailer tongue
weight.
Note: Consult an authorized dealer
to determine the maximum trailer
weight allowed for your vehicle if
you are not sure.

E163167

When attaching the trailer wiring connector
to your vehicle, only use a proper fitting
connector that works with the vehicle and
trailer functions. Some seven-position
connectors may have the SAE J2863 logo,
which confirms that it is the proper wiring
connector and works correctly with your
vehicle.

ESSENTIAL TOWING CHECKS
Follow these guidelines for safe towing:
• Do not tow a trailer until you drive your
vehicle at least 1000 miles (1600
kilometers).
• Consult your local motor vehicle laws
for towing a trailer.
• See the instructions included with
towing accessories for the proper
installation and adjustment
specifications.
• Service your vehicle more frequently if
you tow a trailer. See your scheduled
maintenance information.
• If you use a rental trailer, follow the
instructions the rental agency gives
you.

Color

See Load limits in the Load Carrying
chapter for load specification terms found
on the tire label and Safety Compliance
label and instructions on calculating your
vehicle's load.

Left turn signal and stop lamp

White

Ground (-)

Blue

Electric brakes

Green

Right turn signal and stop
lamp

Orange

Battery (+)

Brown

Running lights

Grey

Reverse lights

Hitches
Do not use a hitch that either clamps onto
the bumper or attaches to the axle. You
must distribute the load in your trailer so
that 10-15% of the total weight of the
trailer is on the tongue.

Remember to account for the trailer
tongue weight as part of your vehicle load
when calculating the total vehicle weight.

201

F150 (TF6) , enUSA

Function

Yellow

Towing
Safety Chains

Weight-distributing Hitches

Note: Do not attach safety chains to the
bumper.

WARNING
Do not adjust a weight-distributing
hitch to any position where the rear
bumper of the vehicle is higher than
it was before attaching the trailer. Doing
so will defeat the function of the
weight-distributing hitch, which may cause
unpredictable handling, and could result
in serious personal injury.

Always connect the safety chains to the
frame or hook retainers of your vehicle
hitch.
To connect the safety chains, cross the
chains under the trailer tongue and allow
enough slack for turning tight corners. Do
not allow the chains to drag on the ground.

When hooking-up a trailer using a
weight-distributing hitch, always use the
following procedure:

Trailer Brakes

Do not connect a trailer's hydraulic
brake system directly to your
vehicle's brake system. Your vehicle
may not have enough braking power and
your chances of having a collision greatly
increase.

WARNING

Park the loaded vehicle, without the
trailer, on a level surface.
Measure the height to the top of your
vehicle's front wheel opening on the
fender. This is H1.
Attach the loaded trailer to your vehicle
without the weight-distributing bars
connected.
Measure the height to the top of your
vehicle's front wheel opening on the
fender a second time. This is H2.
Install and adjust the tension in the
weight-distributing bars so that the
height of your vehicle's front wheel
opening on the fender is approximately
halfway between H1 and H2.
Check that the trailer is level or slightly
nose down toward your vehicle. If not,
adjust the ball height accordingly and
repeat Steps 2-6.

Electric brakes and manual, automatic or
surge-type trailer brakes are safe if you
install them properly and adjust them to
the manufacturer's specifications. The
trailer brakes must meet local and federal
regulations.
The rating for the tow vehicle's braking
system operation is at the gross vehicle
weight rating, not the gross combined
weight rating.
Separate functioning brake systems
are required for safe control of towed
vehicles and trailers weighing more
than 1500 pounds (680 kilograms)
when loaded.

Once the trailer is level or slightly nose
down toward the vehicle:
• Lock the bar tension adjuster in place.
• Check that the trailer tongue securely
attaches and locks onto the hitch.
• Install safety chains, lighting, and trailer
brake controls as required by law or the
trailer manufacturer.

202

F150 (TF6) , enUSA

Towing
Integrated Trailer Brake Controller (If
Equipped)

A: Manual control lever: Slide the control
lever to the left to turn on the trailer's
electric brakes independent of the tow
vehicle's See the following Procedure for
adjusting gain section for instructions on
proper use of this feature. If you use the
manual control while the brake is also
applied, the greater of the two inputs
determines the power sent to the trailer
brakes.

WARNING
The Ford trailer brake controller has
been verified to be compatible with
trailers having electric-actuated
drum brakes (one to four axles) and
electric-over-hydraulic brakes. It will not
activate hydraulic surge-style trailer
brakes. It is the responsibility of the
customer to ensure that the trailer brakes
are adjusted appropriately, functioning
normally and all electric connections are
properly made. Failure to do so may result
in loss of vehicle control, crash or serious
injury.

•

B: + and - (Gain adjustment buttons):
Pressing these buttons adjusts the
controller's power output to the trailer
brakes in 0.5 increments. You can increase
the gain setting to 10.0 (maximum trailer
braking) or decrease it to 0 (no trailer
braking). Pressing and holding a button
raises or lowers the setting continuously.
The gain setting displays in the message
center as follows: TBC GAIN = XX.X.

B
A

E166403

When used properly, the trailer brake
controller assists in smooth and effective
trailer braking by powering the trailer’s
electric or electric-over-hydraulic brakes
with a proportional output based on the
towing vehicle’s brake pressure.
The controller user interface consists of
the following:

203

F150 (TF6) , enUSA

Stop lamps: Using the manual control
lever illuminates both the trailer brake
lamps and your vehicle brake lamps
except the center high-mount stop
lamp, if you make the proper electrical
connection to the trailer. Pressing your
vehicle brake pedal also illuminates
both trailer and vehicle brake lamps.

Towing
The gain setting sets the trailer brake
controller for the specific towing condition.
You should change the setting as towing
conditions change. Changes to towing
conditions include trailer load, vehicle load,
road conditions and weather.

The controller shows gain setting, output
bar graph, and trailer connectivity status
in the information display. They appear in
the information display as follows:
• TBC GAIN = XX.X NO TRAILER:
Shows the current gain setting during
a given ignition cycle and when
adjusting the gain. This also displays if
you use the manual control lever or
make gain adjustments with no trailer
connected.
• TBC GAIN = XX.X OUTPUT=/ / / /
/ /: Displays when you push your
vehicle's brake pedal, or upon use of
the manual control. Bar indicators
illuminate in the information display to
indicate the amount of power going to
the trailer brakes relative to the brake
pedal or manual control input. One bar
indicates the least amount of output;
six bars indicate maximum output.
• TRAILER CONNECTED: Displays
when the system senses a correct
trailer wiring connection (a trailer with
electric trailer brakes) during a given
ignition cycle.
• TRAILER DISCONNECTED: Displays,
accompanied by a single audible time,
when the system senses a trailer
connection and then a disconnection,
either intentional or unintentional,
during a given ignition cycle. It also
displays if a truck or trailer-wiring fault
occurs causing the trailer to appear
disconnected. This message can also
display if you use the manual control
lever without a trailer connected.

The gain should be set to provide the
maximum trailer braking assistance while
making sure the trailer wheels do not lock
when using the brakes. Locked trailer
wheels may lead to trailer instability.
1.

Procedure for Adjusting Gain
Note: Only perform this procedure in a
traffic-free environment at speeds of
approximately 20-25 mph (30-40 km/h).

204

F150 (TF6) , enUSA

Make sure the trailer brakes are in good
working condition, functioning normally
and properly adjusted. See your trailer
dealer if necessary.
Hook up the trailer and make the
electrical connections according to the
trailer manufacturer's instructions.
When you plug in a trailer with electric
or electric-over-hydraulic brakes,
TRAILER CONNECTED appears in
the information display.
Use the gain adjustment (+ and -)
buttons to increase or decrease the
gain setting to the desired starting
point. A gain setting of 6.0 is a good
starting point for heavier loads.
In a traffic-free environment, tow the
trailer on a dry, level surface at a speed
of 20-25 mph (30-40 km/h) and
squeeze the manual control lever
completely.
If the trailer wheels lock up, indicated
by squealing tires, reduce the gain
setting. If the trailer wheels turn freely,
increase the gain setting. Repeat Steps
5 and 6 until the gain setting is at a
point just below trailer wheel lock-up.
If towing a heavier trailer, trailer wheel
lock-up may not be attainable even
with the maximum gain setting of 10.

Towing
Explanation of Information Display
Warning Messages

•

Note: An authorized dealer can diagnose
the trailer brake controller to determine
exactly which trailer fault has occurred.
However, your Ford warranty does not cover
this diagnosis if the fault is with the trailer.

•

TRAILER BRAKE MODULE FAULT:
Displays in response to faults sensed by
the trailer brake controller, accompanied
by a single tone. If this message appears,
contact an authorized dealer as soon as
possible for diagnosis and repair. The
controller may still function, but
performance may be degraded.

•

WIRING FAULT ON TRAILER: Displays
when there is a short circuit on the electric
brake output wire. If the WIRING FAULT
ON TRAILER message displays,
accompanied by a single tone, with no
trailer connected, the problem is with your
vehicle wiring between the trailer brake
controller and the 7-pin connector at the
bumper. If the message only displays with
a trailer connected, the problem is with the
trailer wiring. Consult your trailer dealer for
assistance. This can be a short to ground
(such as a chaffed wire), short to voltage
(such as a pulled pin on trailer emergency
breakaway battery) or the trailer brakes
may be drawing too much current.

•

Points to Remember
•

Note: Do not attempt removal of the trailer
brake controller without consulting the
Workshop Manual. Damage to the unit may
result.
•
•

Adjust gain setting before using the
trailer brake controller for the first time.
Adjust gain setting, using the procedure
above, whenever road, weather and
trailer or vehicle loading conditions
change from when the gain was initially
set.

•

205

F150 (TF6) , enUSA

Only use the manual control lever for
proper adjustment of the gain during
trailer setup. Misuse, such as
application during trailer sway, could
cause instability of trailer or tow
vehicle.
Avoid towing in adverse weather
conditions. The trailer brake controller
does not provide anti-lock control of
the trailer wheels. Trailer wheels can
lock up on slippery surfaces, resulting
in reduced stability of trailer and tow
vehicle.
The trailer brake controller is equipped
with a feature that reduces output at
vehicle speeds below 11 mph (18 km/h)
so trailer and vehicle braking is not jerky
or harsh. This feature is only available
when applying the brakes using your
vehicle's brake pedal, not the
controller.
The controller interacts with the brake
control system and powertrain control
system of your vehicle to provide the
best performance on different road
conditions.
Your vehicle's brake system and the
trailer brake system work
independently of each other. Changing
the gain setting on the controller does
not affect the operation of your
vehicle's brakes whether you attach a
trailer or not.
When you switch the engine off, the
controller output is disabled and the
display and module shut down. The
controller module and display turn on
when you switch the ignition on.
The trailer brake controller is only a
factory-installed or dealer-installed
item. Ford is not responsible for
warranty or performance of the
controller due to misuse or customer
installation.

Towing
Trailer Lamps

•

WARNING
Never connect any trailer lamp wiring
to the vehicle's tail lamp wiring; this
may damage the electrical system
resulting in fire. Contact your authorized
dealer as soon as possible for assistance
in proper trailer tow wiring installation.
Additional electrical equipment may be
required.

•

Trailer lamps are required on most towed
vehicles. Make sure all running lights, brake
lights, turn signals and hazard lights are
working.

•

Using a Step Bumper (If Equipped)
The rear bumper is equipped with an
integral hitch and only requires a ball with
a one-inch (25.4 millimeter) shank
diameter. The bumper has a 5000-pound
(2268 kilogram) trailer weight and a
500-pound (227 kilogram) tongue weight
capacity

•

If it is necessary to relocate the hitch ball
position, you must install a frame-mounted
trailer hitch.

•

Before Towing a Trailer
Practice turning, stopping and backing up
to get the feel of your vehicle-trailer
combination before starting on a trip.
When turning, make wider turns so the
trailer wheels clear curbs and other
obstacles.

•

When Towing a Trailer
•

•

Do not drive faster than 70 mph (113
km/h) during the first 500 miles (800
kilometers).
Do not make full-throttle starts.

•

206

F150 (TF6) , enUSA

Check your hitch, electrical connections
and trailer wheel lug nuts thoroughly
after you have traveled 50 miles (80
kilometers).
When stopped in congested or heavy
traffic during hot weather, place the
gearshift in position P to aid engine and
transmission cooling and to help A/C
performance.
Turn off the speed control with heavy
loads or in hilly terrain. The speed
control may turn off automatically
when you are towing on long, steep
grades.
Shift to a lower gear when driving down
a long or steep hill. Do not apply the
brakes continuously, as they may
overheat and become less effective.
If your transmission is equipped with a
Grade Assist or Tow/Haul feature, use
this feature when towing. This provides
engine braking and helps eliminate
excessive transmission shifting for
optimum fuel economy and
transmission cooling.
If your vehicle is equipped with
AdvanceTrac with RSC, this system
may turn on during typical cornering
maneuvers with a heavily loaded trailer.
This is normal. Turning the corner at a
slower speed while towing may reduce
this tendency.
If you are towing a trailer frequently in
hot weather, hilly conditions, at the
gross combined weight rating (or any
combination of these factors), consider
refilling your rear axle with synthetic
gear lubricant (if the axle is not already
filled with it). See Capacities and
Specifications (page 296).
Allow more distance for stopping with
a trailer attached. Anticipate stops and
brake gradually.
Avoid parking on a grade. However, if
you must park on a grade:

Towing
Replace the rear axle lubricant anytime
the rear axle has been submerged in water.
Water may have contaminated the rear
axle lubricant, which is not normally
checked or changed unless a leak is
suspected or other axle repair is required.

Turn the steering wheel to point your
vehicle tires away from traffic flow.
2. Set your vehicle parking brake.
3. Place the automatic transmission in
position P.
4. Place wheel chocks in front and back
of the trailer wheels. (Chocks not
included with vehicle.)

TRANSPORTING THE VEHICLE

Your vehicle may be equipped with a
temporary or conventional spare tire. A
"temporary" spare tire is different in size
(diameter or width), tread-type
(All-Season or All Terrain) or is from a
different manufacturer than the road tires
on your vehicle. Consult information on the
tire label or Safety Compliance label for
limitations when using.

Launching or Retrieving a Boat or
Personal Watercraft (PWC)
Note: Disconnect the wiring to the trailer
before backing the trailer into the water.
Note: Reconnect the wiring to the trailer
after the trailer is removed from the water.
When backing down a ramp during boat
launching or retrieval:
• Do not allow the static water level to
rise above the bottom edge of the rear
bumper.
• Do not allow waves to break higher
than 6 inches (15 centimeters) above
the bottom edge of the rear bumper.

E143886

If you need to have your vehicle towed,
contact a professional towing service or,
if you are a member of a roadside
assistance program, your roadside
assistance service provider.

Exceeding these limits may allow water to
enter vehicle components:
• Causing internal damage to the
components.
• Affecting driveability, emissions, and
reliability.

We recommend the use of a wheel lift and
dollies or flatbed equipment to tow your
vehicle. Do not tow with a slingbelt. Ford
Motor Company has not approved a
slingbelt towing procedure. Vehicle
damage may occur if towed incorrectly, or
by any other means.

207

F150 (TF6) , enUSA

Towing
Ford Motor Company produces a towing
manual for all authorized tow truck
operators. Have your tow truck operator
refer to this manual for proper hook-up
and towing procedures for your vehicle.

Follow these guidelines if you have a need
for recreational towing, such as towing
your vehicle behind a motorhome. We
designed these guidelines to prevent
damage to your transmission.

It is acceptable to have your two-wheel
drive vehicle towed with the front wheels
on the ground (without dollies) and the
rear wheels off the ground.

Two-wheel Drive Vehicles
You cannot tow a two-wheel drive vehicle
with any wheels on the ground as vehicle
or transmission damage may occur. You
must tow your vehicle with all four wheels
off the ground, such as when using a
car-hauling trailer.

We recommend towing a four-wheel drive
vehicle with all wheels off the ground, such
as using a wheel lift and dollies or flatbed
equipment.

Four-wheel Drive Vehicles

TOWING THE VEHICLE ON
FOUR WHEELS

You can only tow a four-wheel drive
vehicle with all wheels on the ground by
placing the transfer case in its neutral
position and engaging the
four-wheel-down towing feature. Perform
the steps outlined in the following section
after positioning your vehicle behind the
tow vehicle and properly securing them
together.

Emergency Towing
If your vehicle becomes inoperable
(without access to wheel dollies,
car-hauling trailer, or flatbed transport
vehicle), it can be flat-towed (all wheels
on the ground, regardless of the powertrain
and transmission configuration) under the
following conditions:
• Your vehicle is facing forward for
towing in a forward direction.
• Place the transmission in position N. If
you cannot move the transmission into
N, you may need to override it. See
Transmission (page 147).
• Maximum speed is 35 mph (56 km/h).
• Maximum distance is 50 miles (80
kilometers).

Four-wheel-down Towing
1.

Turn the ignition to the on position. Do
not start the engine.
2. Press and hold the brake pedal.
3. Rotate the four-wheel drive switch to
2H.
4. Shift the transmission to position N.
5. Rotate the four-wheel drive switch
from 2H to 4L and back to 2H five
times within seven seconds.
Note: If completed successfully, the
information display shows NEUTRAL TOW
LEAVE IN N or NEUTRAL TOW ENABLED
LEAVE TRANSMISSION IN NEUTRAL.
This indicates that your vehicle is safe to
tow with all wheels on the ground

Recreational Towing
Note: Put your climate control system in
recirculated air mode to prevent exhaust
fumes from entering your vehicle. See
Climate Control (page 106).

Note: If you do not see the message in the
display, you must perform the procedure
again from the beginning.

208

F150 (TF6) , enUSA

Towing
2. Turn the ignition to the on position. Do
not start the engine.
3. Shift the transmission out of N and into
any gear.
4. Release the brake pedal.
Note: If completed successfully, the
instrument cluster displays 4X2, and
NEUTRAL TOW DISABLED.

Note: You may hear an audible noise as the
transfer case shifts into its neutral position.
This is normal.
6. Leave the transmission in position N
and turn the ignition as far as it will go
toward the off position (it will not turn
fully off when the transmission is in
position N. You must leave the key in
the ignition while towing. To lock and
unlock your vehicle, use the keyless
entry keypad or extra set of keys.
7.

Note: If the indicator light and message do
not display, you must perform the procedure
again from the beginning.

Release the brake pedal.

Note: You may hear an audible noise as the
transfer case shifts out of its neutral
position. This is normal.

WARNINGS
Do not disconnect the battery during
recreational towing. Doing so will
prevent the transfer case from
shifting properly and may cause the vehicle
to roll even if the transmission is in P
(Park).

5. Apply the parking brake, and then
disconnect the vehicle from the tow
vehicle.
6. Release the parking brake, start the
engine, and shift the transmission to
position D to make sure the transfer
case is out of position N.
7. If the transfer case does not
successfully shift out of position N, set
the parking brake until you can have
your vehicle serviced.

Shifting the transfer case to its
neutral position for recreational
towing may cause the vehicle to be
able to roll even if the transmission is in P
(Park). The driver or others could be
injured. Make sure the foot brake is
depressed and the vehicle is in a secure
and safe position while the transfer case
is being shifted to its neutral position.
Failing to put the transfer case in its
neutral position will damage vehicle
components.
Note: You can check four-wheel-down
towing status at any time by opening the
driver's door or turning the ignition to the
accessory or on position and verifying the
NEUTRAL TOW ENABLED message
displays in the cluster.
To exit four-wheel-down towing and return
the transfer case to its 2H position:
1.

With your vehicle still properly secured
to the tow vehicle, press and hold the
brake pedal.

209

F150 (TF6) , enUSA

Driving Hints
Avoid these actions; they reduce your fuel
economy:
• Sudden accelerations or hard
accelerations.
• Revving the engine before turning it off.
• Idle for periods longer than one minute.
• Warm up your vehicle on cold
mornings.
• Use the air conditioner or front
defroster.
• Use the speed control in hilly terrain.
• Rest your foot on the brake pedal while
driving.
• Drive a heavily loaded vehicle or tow a
trailer.
• Carry unnecessary weight
(approximately 1 mpg [0.4 km/L] is
lost for every 400 lb [180 kilogram] of
weight carried).
• Driving with the wheels out of
alignment.

BREAKING-IN
You need to break in new tires for
approximately 300 miles (480
kilometers). During this time, your vehicle
may exhibit some unusual driving
characteristics.
Avoid driving too fast during the first 1000
miles (1600 kilometers). Vary your speed
frequently and change up through the
gears early. Do not labor the engine.
Do not tow during the first 1000 miles
(1600 kilometers).

ECONOMICAL DRIVING
Your fuel economy is affected by several
things, such as how you drive, the
conditions you drive under, and how you
maintain your vehicle.
You may improve your fuel economy by
keeping these things in mind:
• Accelerate and slow down in a smooth,
moderate fashion.
• Drive at steady speeds without
stopping.
• Anticipate stops; slowing down may
eliminate the need to stop.
• Combine errands and minimize
stop-and-go driving.
• Close the windows for high-speed
driving.
• Drive at reasonable speeds (traveling
at 55 mph [88 km/h] uses 15% less
fuel than traveling at 65 mph [105
km/h]).
• Keep the tires properly inflated and use
only the recommended size.
• Use the recommended engine oil.
• Perform all regularly scheduled
maintenance.

Conditions
• Heavily loading a vehicle or towing a
trailer may reduce fuel economy at any
speed.
• Adding certain accessories to your
vehicle (for example bug deflectors,
rollbars, light bars, running boards, ski
racks or luggage racks) may reduce
fuel economy.
• To maximize the fuel economy, drive
with the tonneau cover installed (if
equipped).
• Using fuel blended with alcohol may
lower fuel economy.
• Fuel economy may decrease with lower
temperatures during the first 8–10
miles (12–16 kilometers) of driving.
• Driving on flat terrain offers improved
fuel economy as compared to driving
on hilly terrain.

210

F150 (TF6) , enUSA

Driving Hints
•

•

Transmissions give their best fuel
economy when operated in the top
cruise gear and with steady pressure
on the gas pedal.
Four-wheel-drive operation (if
equipped) is less fuel efficient than
two-wheel-drive operation.
Close the windows for high-speed
driving.

FLOOR MATS

DRIVING THROUGH WATER
Note: Driving through deep water above
the recommended levels can cause vehicle
damage.

E142666

WARNINGS
Always use floor mats that are
designed to fit the foot well of your
vehicle, leaving the pedal area
unobstructed, and which can be firmly
secured to retention posts so that they
cannot slip out of position and interfere
with the pedals or impair safe operation of
your vehicle in other ways.

If driving through deep or standing water
is unavoidable, proceed very slowly. Never
drive through water that is higher than the
bottom of the wheel rims (for cars) or the
bottom of the hubs (for trucks).

Incorrectly fitted floor mats can
cause the accelerator pedal to
become stuck in the open position.
This can cause loss of vehicle control.
Always correctly install the floor
mats to the retention posts so that
they cannot slip out of position or
obstruct pedal operation.
E142667

Do not place unsecured floor mats
or any other covering in the foot well.

When driving through water, traction or
brake capability may be limited. Also,
water may enter your engine’s air intake
and severely damage your engine or your
vehicle may stall.

Do not place additional floor mats
or any other covering on top of the
original floor mats. This will reduce
the pedal clearance and interfere with the
pedal operation.

Once through the water, always dry the
brakes by moving your vehicle slowly while
applying light pressure on the brake pedal.
Wet brakes do not stop the vehicle as
quickly as dry brakes.

Do not allow objects to fall or
become trapped under the pedals of
your vehicle. This can cause loss of
vehicle control.
Carry out regular inspections to make
sure the floor mats are secure.
211

F150 (TF6) , enUSA

Driving Hints
To install the floor mats, position the floor
mat eyelet over the retention post and
press down to lock in position.

•

Remove in reverse order.

SNOWPLOWING
For F-150 snowplowing applications, Ford
recommends the F150 4X4 Regular Cab,
SuperCrew or SuperCab, equipped with
the 6.2L engine for residential
snowplowing only.

•

Do not use F-150 vehicles equipped with
the 3.5L, 3.7L or 5.0L engines for
snowplowing.

Installing the Snowplow
Weight limits and guidelines for selecting
and installing the snowplow are in the Ford
Truck Body Builders Layout Book,
snowplow section, found at
www.fleet.ford.com/truckbbas. A typical
installation affects the following:
•

•

212

F150 (TF6) , enUSA

Certification to government safety laws
such as occupant protection and airbag
deployment, braking, and lighting. Look
for an Alterer’s Label on the vehicle
from the snowplow installer certifying
that the installation meets all
applicable Federal Motor Vehicle
Safety Standards (FMVSS).
The Total Accessory Reserve Capacity
(TARC) is on the lower right side of the
vehicle’s Safety Compliance
Certification Label. This applies to
Ford-completed vehicles of
10,000.17 lb (4,536 kg) GVWR or less.
This is the weight of
permanently-attached auxiliary
equipment, such as snowplow
frame-mounting hardware, that can
be added to the vehicle and satisfy
Ford compliance certification to
FMVSS. Exceeding this weight may
require the auxiliary equipment installer
additional safety certification
responsibility. The Front Accessory
Reserve Capacity (FARC) is for the
customer convenience.
Rear ballast weight behind the rear
axle may be required to prevent
exceeding the FGAWR, and provide
front-to-rear weight balance for proper
braking and steering.
Front wheel toe may require
re-adjustment to prevent premature
uneven tire wear. Specifications are in
the Ford Workshop Manual.
Headlight aim may require adjustment.

Driving Hints
•

•

Snowplowing with your Airbag
Equipped Vehicle

The tire air pressures recommended
for general driving are on the vehicle’s
Safety Certification Label. The
maximum cold inflation pressure for
the tire and associated load rating are
on the tire sidewall. Tire air pressure
may require re-adjustment within these
pressure limits to accommodate the
additional weight of the snowplow
installation.
Federal and some local regulations
require additional exterior lamps for
snowplow-equipped vehicles. Consult
your authorized dealer for additional
information.

WARNINGS
Do not attempt to service, repair, or
modify the airbag supplemental
restraint system (SRS) or its fuses.
See your Ford or Lincoln Mercury dealer.
Additional equipment such as
snowplow equipment may affect the
performance of the airbag sensors
increasing the risk of injury. Please refer to
the Body Builders Layout Book for
instructions about the appropriate
installation of additional equipment.
All occupants of the vehicle,
including the driver, should always
properly wear their safety belts, even
when provided with an airbag
supplemental restraint system (SRS).

Operating the Vehicle with the
Snowplow Attached
Note: Drive the vehicle at least 500 miles
(800 kilometers) before using your vehicle
for snow removal.
Ford recommends vehicle speed does not
exceed 45 mph (72 km/h) when
snowplowing.

Your vehicle is equipped with a driver and
passenger airbag supplemental restraint
system. The supplemental restraint system
will activate in certain frontal and offset
frontal collisions when the vehicle sustains
sufficient longitudinal deceleration.

The attached snowplow blade restricts
airflow to the radiator, and may cause the
engine to run at a higher temperature:
Attention to engine temperature is
especially important when outside
temperatures are above freezing. Angle
the blade to maximize airflow to the
radiator and monitor engine temperature
to determine whether a left or right angle
provides the best performance.

Careless or high speed driving while
plowing snow which results in sufficient
vehicle decelerations can deploy the
airbag. Such driving also increases the risk
of accidents.
Never remove or defeat the tripping
mechanisms designed into the snow
removal equipment by its manufacturer.
Doing so may cause damage to the vehicle
and the snow removal equipment as well
as possible airbag deployment.

Follow the severe duty schedule in your
Scheduled Maintenance information for
engine oil and transmission fluid change
intervals.

Engine temperature while plowing
Your engine may run at a higher
temperature than normal because the
attached snowplow blade will restrict
airflow to the radiator:

213

F150 (TF6) , enUSA

Driving Hints
•

•

If you are driving more than 15 miles
(24 kilometers) at temperatures above
freezing, angle the plow blade either
full left or full right to provide
maximum airflow to the radiator.
If you are driving less than 15 miles (24
kilometers) at speeds up to 45 mph
(72 km/h) in cold weather, you will not
need to worry about blade position to
provide maximum airflow.

Transmission operation while
plowing
WARNING
Do not spin the wheels at over 35
mph (55 km/h). The tires may fail
and injure a passenger or bystander.
•

•

Shift transfer case to 4L (4WD Low)
when plowing in small areas at speeds
below5.0 mph (8 km/h).
Shift transfer case to 4H (4WD High)
when plowing larger areas or light snow
at higher speeds. Do not exceed 15 mph
(24 km/h).
Do not shift the transmission from a
forward gear to R (Reverse) until the
engine is at idle and the wheels have
stopped.

Outside Air Temperature While
Plowing
While plowing with your vehicle, the plow
blade can block the sensor airflow and
cause the outside air temperature reading
to be inaccurate.
A Ford wiring kit is available to relocate the
Outside Air Temperature sensor to the
plow blade frame below the headlamp to
provide accurate outside air temperature
readings. See your authorized dealer for
more information.

214

F150 (TF6) , enUSA

Roadside Emergencies
Trailers shall be covered up to $200 if the
disabled eligible vehicle requires service at
the nearest authorized dealer. If the trailer
is disabled, but the towing vehicle is
operational, the trailer does not qualify for
any roadside services.

ROADSIDE ASSISTANCE
Vehicles Sold In The U.S.: Getting
Roadside Assistance
To fully assist you should you have a
vehicle concern, Ford Motor Company
offers a complimentary roadside
assistance program. This program is
separate from the New Vehicle Limited
Warranty. The service is available:
•
•

Vehicles Sold In The U.S. : Using
Roadside Assistance
Complete the roadside assistance
identification card and place it in your
wallet for quick reference. This card is
found in the owner's information portfolio
in the glove compartment.

24 hours, seven days a week.
for the coverage period listed on the
Roadside Assistance Card included in
your Owner's Manual portfolio.

U.S. Ford vehicle customers who require
Roadside Assistance, call 1-800-241-3673.

Roadside assistance will cover:
• a flat tire change with a good spare, if
provided with the vehicle (except
vehicles that have been supplied with
a tire inflation kit).
• battery jump start.
• lock-out assistance (key replacement
cost is the customer's responsibility).
• fuel delivery — Independent Service
Contractors, if not prohibited by state,
local or municipal law, shall deliver up
to 2.0 gallons (7.5 liters) of gasoline or
5.0 gallons (18.9 liters) of diesel fuel
to a disabled vehicle. Fuel delivery
service is limited to two no-charge
occurrences within a 12-month period.
• winch out — available within 100 feet
(30.5 meters) of a paved or county
maintained road, no recoveries.
• towing — Ford and Lincoln eligible
vehicles towed to an authorized dealer
within 35 miles (56.3 kilometers) of the
disablement location or to the nearest
authorized dealer. If a member
requests to be towed to an authorized
dealer more than 35 miles (56.3
kilometers) from the disablement
location, the member shall be
responsible for any mileage costs in
excess of 35 miles (56.3 kilometers).

If you need to arrange roadside assistance
for yourself, Ford Motor Company will
reimburse a reasonable amount for towing
to the nearest dealership within 35 miles
(56.3 kilometers). To obtain
reimbursement information, U.S. Ford
vehicle customers call 1-800-241-3673.
Customers will be asked to submit their
original receipts.

Vehicles Sold In Canada : Getting
Roadside Assistance
Canadian customers who require roadside
assistance, call 1-800-665-2006.

Vehicles Sold In Canada : Using
Roadside Assistance
For your convenience, you may complete
the roadside assistance identification card
found in the centerfold of your warranty
guide and retain for future reference.
Canadian roadside coverage and benefits
may differ from the U.S. coverage. If you
require more information, please refer to
the coverage section of your warranty
guide, call us in Canada at
1-800-665-2006, or visit our website at
www.ford.ca.

215

F150 (TF6) , enUSA

Roadside Emergencies
For vehicles equipped with a push button
start system:
1. Press the START/STOP button to
switch off the ignition.
2. Press the brake pedal and press the
START/STOP button to start the
vehicle.
3. Remove your foot from the brake pedal
and press the START/STOP button
to switch off the ignition.
4. You can either attempt to start the
engine by pressing the brake pedal and
the START/STOP button, or switch
on the ignition only by pressing the
START/STOP button without
pressing the brake pedal. Both ways
re-enable the fuel system.

HAZARD WARNING FLASHERS
Note: The hazard warning flashers will
operate when the ignition is in any position
or if the key is not in the ignition. If used
when the engine is not running, the battery
will lose charge. As a result, there may be
insufficient power to restart your engine.
The hazard flasher control is
located on the instrument panel
E142663
by the radio. Use it when your
vehicle is disabled and is creating a safety
hazard for other motorists.
•
•

Press the flasher control and all front
and rear direction indicators flash.
Press the flasher control again to turn
them off.

Note: When you try to restart your vehicle
after a fuel shutoff, the vehicle makes sure
that various systems are safe to restart.
Once your vehicle determines that the
systems are safe, then the vehicle will allow
you to restart.

FUEL SHUTOFF
WARNING
Failure to inspect and, if necessary,
repair fuel leaks after a collision may
increase the risk of fire and serious
injury. Ford Motor Company recommends
that the fuel system be inspected by an
authorized dealer after any collision.

Note: In the event that your vehicle does
not restart after your third attempt, contact
an authorized dealer.

JUMP STARTING THE VEHICLE

In the event of a moderate to severe
collision, this vehicle is equipped with a
fuel pump shut-off feature that stops the
flow of fuel to the engine. Not every impact
will cause a shut-off.

WARNINGS
The gases around the battery can
explode if exposed to flames, sparks,
or lit cigarettes. An explosion could
result in personal injury or vehicle damage.

Should your vehicle shut off after a
collision, you may restart your vehicle. For
vehicles equipped with a key system:
1. Switch off the ignition.
2. Switch on the ignition.
3. Repeat Steps 1 and 2 to re-enable the
fuel pump.

Batteries contain sulfuric acid which
can burn skin, eyes and clothing, if
contacted.
Use only an adequate-sized cable
with insulated clamps.

216

F150 (TF6) , enUSA

Roadside Emergencies
Preparing Your Vehicle
Note: Do not attempt to push-start your
automatic transmission vehicle. Automatic
transmissions do not have push-start
capability. Attempting to push-start a
vehicle with an automatic transmission may
cause transmission damage.

Note: Use only a 12-volt supply to start your
vehicle.
Note: Do not disconnect the battery of the
disabled vehicle as this could damage the
vehicle's electrical system.

Park the booster vehicle close to the hood
of the disabled vehicle, making sure the
two vehicles do not touch. Turn all
accessories off.

Connecting the Jumper Cables
WARNING
Do not attach the cables to fuel lines,
engine rocker covers, the intake
manifold or electrical components
as grounding points. Stay clear of moving
parts. To avoid reverse polarity
connections, make sure that you correctly
identify the positive (+) and negative (-)
terminals on both the disabled and booster
vehicles before connecting the cables.

E142664

Connect the positive (+) jumper cable
to the positive (+) terminal of the
discharged battery.
2. Connect the other end of the positive
(+) cable to the positive (+) terminal
of the assisting battery.
3. Connect the negative (-) cable to the
negative (-) terminal of the assisting
battery.
4. Make the final connection of the
negative (-) cable to an exposed metal
part of the stalled vehicle's engine, or
connect the negative (-) cable to a
ground connection point if available.

Note: In the illustration, the bottom vehicle
represents the booster vehicle.

WARNING
Do not connect the end of the
second cable to the negative (-)
terminal of the battery to be jumped.
A spark may cause an explosion of the
gases that surround the battery.

217

F150 (TF6) , enUSA

Roadside Emergencies
Jump Starting

2. Remove the jumper cable on the
negative (-) terminal of the booster
vehicle's battery.
3. Remove the jumper cable from the
positive (+) terminal of the booster
vehicle's battery.
4. Remove the jumper cable from the
positive (+) terminal of the disabled
vehicle's battery.

Start the engine of the booster vehicle
and rev the engine moderately, or press
the accelerator gently to keep your
engine speed between 2000 and 3000
rpms, as shown in your tachometer.
2. Start the engine of the disabled vehicle.
3. Once the disabled vehicle has been
started, run both vehicle engines for an
additional three minutes before
disconnecting the jumper cables.

Removing the Jumper Cables

After the disabled vehicle has been started
and the jumper cables removed, allow it
to idle for several minutes so the battery
can recharge.

Remove the jumper cables in the reverse
order that they were connected.

POST-CRASH ALERT SYSTEM
The system flashes the turn signal lamps
and sounds the horn (intermittently) in the
event of a serious impact that deploys an
airbag (front, side, side curtain or Safety
Canopy) or the safety belt pretensioners.

The horn and lamps will turn off when:
• The hazard control button is pressed
• The panic button (if equipped) is
pressed on the remote entry
transmitter
• Your vehicle runs out of power

3
E142665

Remove the jumper cable from the
ground metal surface or connecting
point, if available.

218

F150 (TF6) , enUSA

Customer Assistance
These are some of the items that can be
found online:
• U.S. dealer locator by Dealer Name,
City/State, or Zip Code
• Owner Manuals
• Maintenance Schedules
• Recalls
• Ford Extended Service Plans
• Ford Genuine Accessories
• Service specials and promotions.

GETTING THE SERVICES YOU
NEED
Warranty repairs to your vehicle must be
performed by an authorized dealer. While
any authorized dealer handling your vehicle
line will provide warranty service, we
recommend you return to your selling
authorized dealer who wants to ensure
your continued satisfaction.
Please note that certain warranty repairs
require special training and equipment, so
not all authorized dealers are authorized
to perform all warranty repairs. This means
that, depending on the warranty repair
needed, you may have to take your vehicle
to another authorized dealer.

In Canada:
Mailing address
Customer Relationship Centre
Ford Motor Company of Canada, Limited
P.O. Box 2000
Oakville, Ontario L6K 0C8

A reasonable time must be allowed to
perform a repair after taking your vehicle
to the authorized dealer. Repairs will be
made using Ford or Motorcraft® parts, or
remanufactured or other parts that are
authorized by Ford.

Telephone
1-800-565-3673 (FORD)
Online
www.ford.ca

Away From Home

Additional Assistance

If you are away from home when your
vehicle needs service, contact the Ford
Customer Relationship Center or use the
online resources listed below to find the
nearest authorized dealer.

If you have questions or concerns, or are
unsatisfied with the service you are
receiving, follow these steps:
1.

Contact your Sales Representative or
Service Advisor at your selling/servicing
authorized dealer.
2. If your inquiry or concern remains
unresolved, contact the Sales Manager,
Service Manager or Customer Relations
Manager.
3. If you require assistance or clarification
on Ford Motor Company policies,
please contact the Ford Customer
Relationship Center.

In the United States:
Mailing address
Ford Motor Company
Customer Relationship Center
P.O. Box 6248
Dearborn, MI 48121
Telephone
1-800-392-3673 (FORD)
(TDD for the hearing impaired:
1-800-232-5952)
Online
Additional information and resources are
available online at www.fordowner.com
219

F150 (TF6) , enUSA

Customer Assistance
In order to help you serve you better,
please have the following information
available when contacting a Customer
Relationship Center:
• Vehicle Identification Number.
• Your telephone number (home and
business).
• The name of the authorized dealer and
city where located.
• The vehicle’s current odometer reading.

California Civil Code Section 1793.22(b)
presumes that the manufacturer has had
a reasonable number of attempts to
conform the vehicle to its applicable
express warranties if, within the first 18
months of ownership of a new vehicle or
the first 18000 miles (29 000 km),
whichever occurs first:
1.

Two or more repair attempts are made
on the same non-conformity likely to
cause death or serious bodily injury OR
2. Four or more repair attempts are made
on the same nonconformity (a defect
or condition that substantially impairs
the use, value or safety of the vehicle)
OR
3. The vehicle is out of service for repair
of nonconformities for a total of more
than 30 calendar days (not necessarily
all at one time).

In some states, you must directly notify
Ford in writing before pursuing remedies
under your state’s warranty laws. Ford is
also allowed a final repair attempt in some
states.
In the United States, a warranty dispute
must be submitted to the BBB AUTO LINE
before taking action under the
Magnuson-Moss Warranty Act, or to the
extent allowed by state law, before
pursuing replacement or repurchase
remedies provided by certain state laws.
This dispute handling procedure is not
required prior to enforcing state created
rights or other rights which are independent
of the Magnuson-Moss Warranty Act or
state replacement or repurchase laws.

In the case of 1 or 2 above, the consumer
must also notify the manufacturer of the
need for the repair of the nonconformity
at the following address:
Ford Motor Company
16800 Executive Plaza Drive
Mail Drop 3NE-B
Dearborn, MI 48126
You are required to submit your warranty
dispute to BBB AUTO LINE before asserting
in court any rights or remedies conferred
by California Civil Code Section 1793.22(b).
You are also required to use BBB AUTO
LINE before exercising rights or seeking
remedies created by the Federal
Magnuson-Moss Warranty Act, 15 U.S.C.
sec. 2301 et seq. If you choose to seek
redress by pursuing rights and remedies
not created by California Civil Code Section
1793.22(b) or the Magnuson-Moss
Warranty Act, resort to BBB AUTO LINE is
not required by those statutes.

IN CALIFORNIA (U.S. ONLY)
California Civil Code Section 1793.2(d)
requires that, if a manufacturer or its
representative is unable to repair a motor
vehicle to conform to the vehicle’s
applicable express warranty after a
reasonable number of attempts, the
manufacturer shall be required to either
replace the vehicle with one substantially
identical or repurchase the vehicle and
reimburse the buyer in an amount equal to
the actual price paid or payable by the
consumer (less a reasonable allowance
for consumer use). The consumer has the
right to choose whether to receive a refund
or replacement vehicle.

220

F150 (TF6) , enUSA

Customer Assistance
already taken to try to resolve them. A
Customer Claim Form will be mailed that
will need to be completed, signed and
returned to the BBB along with proof of
ownership. Upon receipt, the BBB will
review the claim for eligibility under the
Program Summary Guidelines.

THE BETTER BUSINESS
BUREAU (BBB) AUTO LINE
PROGRAM (U.S. ONLY)
Your satisfaction is important to Ford
Motor Company and to your dealer. If a
warranty concern has not been resolved
using the three-step procedure outlined
earlier in this chapter in the Getting the
Services you need section, you may be
eligible to participate in the BBB AUTO
LINE program.

You can get more information by
calling BBB AUTO LINE at
1-800-955-5100, or writing to:
BBB AUTO LINE
4200 Wilson Boulevard, Suite 800
Arlington, Virginia 22203-1833

The BBB AUTO LINE program consists of
two parts – mediation and arbitration.
During mediation, a representative of the
BBB will contact both you and Ford Motor
Company to explore options for settlement
of the claim. If an agreement is not reached
during mediation or you do not want to
participate in mediation, and if your claim
is eligible, you may participate in the
arbitration process. An arbitration hearing
will be scheduled so that you can present
your case in an informal setting before an
impartial person. The arbitrator will
consider the testimony provided and make
a decision after the hearing.

BBB AUTO LINE applications can also be
requested by calling the Ford Motor
Company Customer Relationship Center
at 1-800-392-3673.
Note: Ford Motor Company reserves the
right to change eligibility limitations, modify
procedures, or to discontinue this process
at any time without notice and without
obligation.

UTILIZING THE
MEDIATION/ARBITRATION
PROGRAM (CANADA ONLY)

Disputes submitted to the BBB AUTO LINE
program are usually decided within forty
days after you file your claim with the BBB.
You are not bound by the decision, and
may reject the decision and proceed to
court where all findings of the BBB Auto
Line dispute, and decision, are admissible
in the court action. Should you choose to
accept the BBB AUTO LINE decision, Ford
is then bound by the decision, and must
comply with the decision within 30 days
of receipt of your acceptance letter.

For vehicles delivered to authorized
Canadian dealers. In those cases where
you continue to feel that the efforts by Ford
of Canada and the authorized dealer to
resolve a factory-related vehicle service
concern have been unsatisfactory, Ford of
Canada participates in an impartial third
party mediation/arbitration program
administered by the Canadian Motor
Vehicle Arbitration Plan (CAMVAP).
The CAMVAP program is a straight forward
and relatively speedy alternative to resolve
a disagreement when all other efforts to
produce a settlement have failed. This
procedure is without cost to you and is
designed to eliminate the need for lengthy
and expensive legal proceedings.

BBB AUTO LINE Application: Using the
information provided below, please call or
write to request a program application.
You will be asked for your name and
address, general information about your
new vehicle, information about your
warranty concerns, and any steps you have
221

F150 (TF6) , enUSA

Customer Assistance
In the CAMVAP program, impartial
third-party arbitrators conduct hearings at
mutually convenient times and places in
an informal environment. These impartial
arbitrators review the positions of the
parties, make decisions and, when
appropriate, render awards to resolve
disputes. CAMVAP decisions are fast, fair,
and final as the arbitrator’s award is
binding on both you and Ford of Canada.

If your vehicle must be serviced while you
are traveling or living in Asia-Pacific Region,
Sub-Saharan Africa, U.S. Virgin Islands,
Central America, the Caribbean, and Israel,
contact the nearest authorized dealer. If
the authorized dealer cannot help you,
contact:
FORD MOTOR COMPANY
Customer Relationship Center
1555 Fairlane Drive
Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A.
Telephone: (313) 594-4857
Fax: (313) 390-0804
Email: expcac@ford.com

CAMVAP services are available in all
Canadian territories and provinces. For
more information, without charge or
obligation, call your CAMVAP Provincial
Administrator directly at 1-800-207-0685
or visit www.camvap.ca.

For customers in Guam, the
Commonwealth of the Northern Mariana
Islands (CNMI), America Samoa, and the
U.S. Virgin Islands, please feel free to call
our Toll-Free Number: (800) 841-FORD
(3673).

GETTING ASSISTANCE
OUTSIDE THE U.S. AND
CANADA
Before exporting your vehicle to a foreign
country, contact the appropriate foreign
embassy or consulate. These officials can
inform you of local vehicle registration
regulations and where to find unleaded
fuel.

If your vehicle must be serviced while you
are traveling or living in Puerto Rico,
contact the nearest authorized dealer. If
the authorized dealer cannot help you,
contact:
FORD MOTOR COMPANY
Customer Relationship Center
1555 Fairlane Drive
Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A.
Telephone: (800) 841-FORD (3673)
FAX: (313) 390-0804
Email: prcac@ford.com
www.ford.com.pr

If you cannot find unleaded fuel or can only
get fuel with an anti-knock index lower
than is recommended for your vehicle,
contact our Customer Relationship Center.
The use of leaded fuel in your vehicle
without proper conversion may damage
the effectiveness of your emission control
system and may cause engine knocking or
serious engine damage. Ford Motor
Company or Ford of Canada is not
responsible for any damage caused by use
of improper fuel. Using leaded fuel may
also result in difficulty importing your
vehicle back into the United States.

If your vehicle must be serviced while you
are traveling or living in the Middle East,
contact the nearest authorized dealer. If
the authorized dealer cannot help you,
contact:

222

F150 (TF6) , enUSA

Customer Assistance
FORD MOTOR COMPANY
Customer Relationship Center
1555 Fairlane Drive
Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A.
Telephone: +971 4 3326084
Toll-Free Number of the Kingdom of Saudi
Arabia: 800 8971409
Local Telephone Number of Kuwait:
24810575
FAX: +971 4 3327299
Email: menacac@ford.com
www.me.ford.com

Monday-Friday 8:00 a.m. - 6:00 p.m. EST
Helm, Incorporated can also be reached
by their website:
www.helminc.com
(Items in this catalog may be purchased
by credit card, check or money order.)

Obtaining a French Owner’s
Manual
French Owner’s Manual can be obtained
from your authorized dealer or by
contacting Helm, Incorporated using the
contact information listed previously in this
section.

If you buy your vehicle in North America
and then relocate to any of the above
locations, register your vehicle
identification number (VIN) and new
address with Ford Motor Company Export
Operations & Global Growth Initiatives by
emailing expcac@ford.com.

REPORTING SAFETY DEFECTS
(U.S. ONLY)

If you are in another foreign country,
contact the nearest authorized dealer. In
the event your inquiry is unresolved,
communicate your concern with the
dealership’s Sales Manager, Service
Manager or Customer Relations Manager.
If you require additional assistance or
clarification, please contact the respective
Customer Relationship Center as
previously listed.

E142557

If you believe that your vehicle has
a defect which could cause a
crash or could cause injury or
death, you should immediately
inform the National Highway
Traffic Safety Administration
(NHTSA) in addition to notifying
Ford Motor Company.
If NHTSA receives similar
complaints, it may open an
investigation, and if it finds that a
safety defect exists in a group of
vehicles, it may order a recall and
remedy campaign. However,
NHTSA cannot become involved
in individual problems between
you, your dealer, or Ford Motor
Company.

Customers in the U.S. should call
1-800-392-3673.

ORDERING ADDITIONAL
OWNER'S LITERATURE
To order the publications in this portfolio,
contact Helm, Incorporated at:
HELM, INCORPORATED
47911 Halyard Drive
Plymouth, Michigan 48170
Attention: Customer Service
Or to order a free publication catalog, call
toll free: 1-800-782-4356
223

F150 (TF6) , enUSA

Customer Assistance
To contact NHTSA, you may call
the Vehicle Safety Hotline
toll-free at 1-888-327-4236 (TTY:
1-800-424-9153); go to
http://www.safercar.gov; or write
to:
Administrator
1200 New Jersey Avenue,
Southeast
Washington, D.C. 20590

You can also obtain other
information about motor vehicle
safety from
http://www.safercar.gov.
REPORTING SAFETY DEFECTS
(CANADA ONLY)
If you believe that your vehicle has
a defect which could cause a
crash or could cause injury or
death, you should immediately
inform Transport Canada.

Transport Canada Contact Information

Website

http://www.tc.gc.ca/eng/roadsafety/menu.htm

Phone

1–800–333–0510

224

F150 (TF6) , enUSA

Fuses
The power distribution box is located in
the engine compartment. It has
high-current fuses that protect your
vehicle's main electrical systems from
overloads.

FUSE SPECIFICATION CHART
Power Distribution Box
WARNINGS
Always disconnect the battery before
servicing high current fuses.

If you disconnect and reconnect the
battery, you will need to reset some
features. See Changing the 12V Battery
(page 246).

To reduce risk of electrical shock,
always replace the cover to the
power distribution box before
reconnecting the battery or refilling fluid
reservoirs.

E166589

Fuse or relay number

Fuse amp rating

Protected components

Relay

Powertrain control module (3.7L, 5.0L and
6.2L engines)

Relay

Starter

Relay

Blower motor

Relay

Rear window defroster

Relay

Electric fan (high speed)

Relay

Trailer tow park lamp

Relay

Run/start

225

F150 (TF6) , enUSA

Fuses
Fuse or relay number

Fuse amp rating

Protected components

Relay

Fuel pump

Relay

Trailer tow battery charger

Relay

Powertrain control module (3.5L engine)

30A*

Power running board motors

40A*

Electric fan (3.7L, 5.0L)

50A*

Electric fan (3.5L, 6.2L with max trailer tow,
SVT Raptor)

30A*

Starter relay power

30A*

Passenger power seat

40A*

Electric fan (3.7L, 5.0L)

50A*

Electric fan (3.5L, 6.2L with max trailer tow,
SVT Raptor)

20A*

High-intensity discharge headlamp –
passenger side

30A*

Trailer brake control

30A*

Auxiliary switch 1 (SVT Raptor)

30A*

Auxiliary switch 2 (SVT Raptor)

20A*

4x4 module (electronic shift)

30A*

Trailer tow battery charge relay power

20A*

Auxiliary power point (instrument panel)

Relay

Air conditioner clutch

—

Not used

—

Not used

10A**

Powertrain control module – keep alive
power and relay coil, canister vent solenoid
(3.7L, 5.0L and 6.2L engines)

20A**

Fuel pump relay power

10A**

Auxiliary switch 4 (SVT Raptor)

10A**

4x4 integrated wheel end solenoid

226

F150 (TF6) , enUSA

Fuses
Fuse or relay number

Fuse amp rating

Protected components

10A**

Air conditioner clutch relay power

15A**

Run/start relay power

40A*

Rear window defroster relay power, Heated
mirror relay power

40A*

110-volt AC power point

40A*

Powertrain control module relay power
(3.7L, 5.0L and 6.2L engines)

50A*

Powertrain control module relay power
(3.5L engine)

20A*

High-intensity discharge headlamps –
driver side

30A*

Roll stability control / Anti-lock brake
system

Relay

Trailer tow left stop/turn

Relay

Trailer tow right stop/turn

Relay

Trailer tow back-up lamps

Relay

Electric fan

15A**

Front camera washer (SVT Raptor)

5A**

Run/start relay coil

15A**

Trailer tow back-up lamp relay power

15A**

Auxiliary switch 3 (SVT Raptor), Trailer tow
power folding mirrors

10A**

Alternator sensor (3.5L, 3.7L and 5.0L
engines)

10A**

Brake on/off switch

60A*

Roll stability control / Anti-lock brake
system module

20A*

Moonroof

30A*

Wiper relay power

—

Not used

227

F150 (TF6) , enUSA

Fuses
Fuse or relay number

Fuse amp rating

Protected components

40A*

Blower motor relay power

5A**

Run/start – Electronic power assist
steering, Blower relay coil

5A**

Run/start – Powertrain control module

5A**

Run/start – 4x4 module, Back-up lamps,
Roll stability control /Anti-lock brake
system, Trailer tow battery charge relay
coil, Rear window defroster relay coil, Front
camera washer relay coil (SVT Raptor)

—

15A**

—

Not used

—

Not used

—

Not used

—

Not used

—

Not used

Not used
Heated mirrors

Relay

Wiper motor

25A*

Electric fan relay power

—

20A*

Auxiliary power point (instrument panel)

20A*

Auxiliary power point (inside center
console)

Not used

20A*

Trailer tow park lamps relay power

25A*

4x4 module, 4x2 elocker module

30A*

Front heated or heated/cooled seats

—

Not used

20A*

Heated rear seats

20A*

Auxiliary power point (rear)

20A*

Trailer tow stop/turn lamps relay power

228

F150 (TF6) , enUSA

Fuses
Fuse or relay number

Fuse amp rating

Protected components

30A*

Driver power seat/memory module

15A**

Powertrain control module – voltage
power 1 (3.7L, 5.0L, 6.2L engines)

25A**

Powertrain control module – voltage
power 1 (3.5L engine)

20A**

Powertrain control module – Voltage
power 2: General powertrain components
(Mass air flow/Intake air temp sensor 3.7L, 5.0L, 6.2L engines) (Canister vent
solenoid - 3.5L engine)

10A**

Powertrain control module – Voltage
power 3 (Emission related powertrain
components, Electric fan relays coil)

15A**

Powertrain control module – Voltage
power 4 – Ignition coils (3.5L, 3.7L, 5.0L
engines)

20A**

Powertrain control module – Voltage
power 4 – Ignition coils (6.2L engine)

5A**

—

Not used

—

Not used

—

Not used

—

Not used

—

Relay

Rain sensor

Not used
Electric fan (low speed)

*Cartridge fuses
**Mini fuses
To remove the trim panel, pull it toward
you and swing it away from the side. To
reinstall it, line up the tabs with the grooves
on the panel, and then push it shut.

Passenger Compartment Fuse
Panel
The fuse panel is in the right-hand side of
the passenger footwell behind a trim panel.

To remove the fuse panel cover, press in
the tabs on both sides of the cover, and
then pull it off.

229

F150 (TF6) , enUSA

Fuses
To reinstall the fuse panel cover, place the
top part of the cover on the fuse panel and
push the bottom part until it latches.

Gently pull on the cover to make sure it has
latched properly.

E163102

Fuse or relay number

Fuse amp rating

30A

Driver side front window

Protected components

15A

SYNC , Display module (8 inch)

30A

Passenger side front window

10A

Interior lamps

20A

Memory module

Not used (spare)

7.5A

Power mirror switch, Memory seat module

10A

Not used (spare)

10A

Radio display, GPS module, Electric finish
panel module

230

F150 (TF6) , enUSA

Fuses
Fuse or relay number

Fuse amp rating

Protected components

10A

Run/accessory relay

10A

Instrument cluster

15A

Interior lighting, Puddle lamps, Backlighting, Cargo lamp

15A

Right turn signals/stop lamps

15A

Left turn signals/stop lamps

15A

Reverse lights, High-mounted stop lamp

10A

Right low-beam headlamp

10A

Left low-beam headlamp

10A

Brake-shift interlock, Keypad illumination,
Powertrain control module wake-up,
Passive anti-theft system

20A

Audio amplifier

20A

Power door locks

10A

Not used (spare)

20A

Horn

15A

Steering wheel control module

15A

Datalink connector, Steering wheel control
module

15A

Not used (spare)

Radio frequency module

20A

Not used (spare)

15A

Ignition switch

20A

Radio

15A

Front parking lamps

Brake on/off – Instrument panel, Engine

15A

Delay/accessory – moonroof, power
windows, locks, Automatic dimming
mirror/Compass, Trailer tow power telescope mirrors

231

F150 (TF6) , enUSA

Fuses
Fuse or relay number

Fuse amp rating

Protected components

10A

Rear heated seats

10A

Reverse sensing system, 4x4 switch, Rear
video, Off-road indicator (SVT Raptor),
Front video (SVT Raptor), Camera splice
module (SVT Raptor)

Hill descent switch (SVT Raptor)

10A

Restraint control module, Occupant classification system module

10A

Trailer brake control

10A

Delayed accessory – 110-volt power point,
Radio

15A

High-beam headlamps

10A

Rear park lamps

7.5A

Passenger airbag deactivation indicator,
Auxiliary switch (SVT Raptor)

Overdrive cancel switch

10A

Not used (spare)

10A

Not used (spare)

10A

Climate controls module

15A

Fog lamps, Exterior mirror turn signals

30A Circuit breaker

Relay

Power windows, Power sliding back
window
Delayed accessory

232

F150 (TF6) , enUSA

Fuses
Auxiliary relay box (SVT Raptor
only)

The relay box is located in the left-hand
corner of the engine compartment near
the windshield.

E166634

Fuse or relay number

Fuse amp rating

Relay

Auxiliary switch 1

Protected components

Relay

Auxiliary switch 2

Relay

Auxiliary switch 3

Relay

Auxiliary switch 4

Relay

Front camera washer

—

Not used

CHANGING A FUSE
Fuses
E142430

WARNING

If electrical components in the vehicle are
not working, a fuse may have blown. Blown
fuses are identified by a broken wire within
the fuse. Check the appropriate fuses
before replacing any electrical
components.

Always replace a fuse with one that
has the specified amperage rating.
Using a fuse with a higher amperage
rating can cause severe wire damage and
could start a fire.

233

F150 (TF6) , enUSA

Fuses
Standard Fuse Amperage Rating and Color
Color
Fuse rating

Mini fuses

Standard
fuses

Maxi fuses

Cartridge
maxi fuses

Fuse link
cartridge

Grey

Violet

Pink

Tan

7.5A

Brown

10A

Red

15A

Blue

20A

Yellow

Blue

25A

Natural

30A

Green

Pink

40A

Orange

Green

50A

Red

60A

Blue

Yellow

70A

Tan

Brown

80A

Natural

Black

234

F150 (TF6) , enUSA

Maintenance
Working with the Engine Off

GENERAL INFORMATION

Set the parking brake and shift to P
(Park).
2. Turn off the engine and remove the key
(if equipped).
3. Block the wheels.
1.

Have your vehicle serviced regularly to help
maintain its roadworthiness and resale
value. There is a large network of Ford
authorized dealers that are there to help
you with their professional servicing
expertise. We believe that their specially
trained technicians are best qualified to
service your vehicle properly and expertly.
They are supported by a wide range of
highly specialized tools developed
specifically for servicing your vehicle.

Working with the Engine On
WARNING
To reduce the risk of vehicle damage
and/or personal burn injuries, do not
start your engine with the air cleaner
removed and do not remove it while the
engine is running.

To help you service your vehicle, we
provide scheduled maintenance
information which makes tracking routine
service easy. See Scheduled
Maintenance (page 438).

Set the parking brake and shift to P
(Park).
2. Block the wheels

If your vehicle requires professional service,
your authorized dealer can provide the
necessary parts and service. Check your
warranty information to find out which
parts and services are covered.

OPENING AND CLOSING THE
HOOD

Use only recommended fuels, lubricants,
fluids and service parts conforming to
specifications. Motorcraft® parts are
designed and built to provide the best
performance in your vehicle.

Precautions
•
•
•

•

Do not work on a hot engine.
Make sure that nothing gets caught in
moving parts.
Do not work on a vehicle with the
engine running in an enclosed space,
unless you are sure you have enough
ventilation.
Keep all open flames and other burning
material (such as cigarettes) away
from the battery and all fuel related
parts.

E166491

235

F150 (TF6) , enUSA

Inside the vehicle, pull the hood release
handle located under the left hand side
of the instrument panel.

Maintenance
2. Go to the front of the vehicle and
locate the secondary release lever. The
release lever is located on the front
bumper, under the grille.
3. Release the hood latch by pushing the
yellow secondary release lever to your
left, toward the center of the vehicle.
4. Lift the hood until the lift cylinders hold
it open.
5. To close, lower the hood and make
sure that the hood is closed properly
and fully latched.

E166492

UNDER HOOD OVERVIEW - 3.5L ECOBOOST™

H
E166496

Windshield washer fluid reservoir

Battery

Engine oil filler cap

236

F150 (TF6) , enUSA

G
A

Maintenance
D.

Engine oil dipstick

Brake fluid reservoir

Engine coolant reservoir

Air filter assembly

Power distribution box

UNDER HOOD OVERVIEW - 3.7L

B
A

E166493

Windshield washer fluid reservoir

Battery

Engine oil filler cap (out of view)

Engine oil dipstick

Brake fluid reservoir

Engine coolant reservoir

237

F150 (TF6) , enUSA

D
A

E
A

F
A

Maintenance
G.

Air filter assembly

Power distribution box

UNDER HOOD OVERVIEW - 5.0L

B
A

C
A

D
A

H
A

E166494

Windshield washer fluid reservoir

Battery

Engine oil filler cap

Engine oil dipstick

Brake fluid reservoir

Engine coolant reservoir

Air filter assembly

Power distribution box

238

F150 (TF6) , enUSA

E A
A
F

G
A

Maintenance
UNDER HOOD OVERVIEW - 6.2L

B
A

C
A

H
A

G
A

E166495

Windshield washer fluid reservoir

Engine oil dipstick

Brake fluid reservoir

Engine coolant reservoir

Air filter assembly

Power steering fluid reservoir

Power distribution box

Engine oil filler cap

Battery

239

F150 (TF6) , enUSA

A
F

A
E

D
A

Maintenance
6. Wipe the dipstick clean. Insert the
dipstick fully, then remove it again.
• If the oil level is between the lower
and upper holes, the oil level is
acceptable. DO NOT ADD OIL.
• If the oil level is below the lower
hole, add enough oil to raise the
level within the lower and upper
holes.
• Oil levels above the upper hole may
cause engine damage. Some oil
must be removed from the engine
by an authorized dealer.
7. Put the oil level dipstick back into the
oil dipstick tube and ensure it is fully
seated.

ENGINE OIL DIPSTICK

E161560

MIN

MAX

Adding Engine Oil

ENGINE OIL CHECK

Note: Do not remove the filler cap when
the engine is running.

Note: Do not remove the engine oil level
dipstick when the engine is running.

2.
3.
4.
5.

Make sure that your vehicle is on level
ground.
Turn the engine off and wait 15 minutes
for the oil to drain into the oil pan.
Set the parking brake and ensure the
gearshift is in PPark.
Open the hood. Protect yourself from
engine heat.
Locate and carefully remove the engine
oil level dipstick. See Under Hood
Overview (page 236). in this chapter
for location of the dipstick.

Note: Do not add oil further than the MAX
mark. Oil levels above the MAX mark may
cause engine damage.

E142732

240

F150 (TF6) , enUSA

Maintenance
Only use oils certified for gasoline engines
by the American Petroleum Institute (API).
An oil with this trademark symbol
conforms to the current engine and
emission system protection standards and
fuel economy requirements of the
International Lubricants Specification
Advisory Council (ILSAC), comprised of
U.S. and Japanese automobile
manufacturers.

WARNINGS
To reduce the risk of personal injury,
make sure the engine is cool before
unscrewing the coolant pressure
relief cap. The cooling system is under
pressure. steam and hot liquid can come
out forcefully when you loosen the cap
slightly.
Do not add coolant further than the
MAX mark.

1. Check the engine oil level.
2. If the engine oil level is not within the
normal range, add engine oil that
meets Ford specifications. See
Capacities and Specifications (page
296).
3. Remove the engine oil filler cap and
use a funnel to pour the engine oil into
the opening.
4. Recheck the engine oil level. Make sure
the oil level is not above the normal
operating range on the engine oil level
dipstick.
5. Install the engine oil level dipstick and
ensure it is fully seated.
6. Fully install the engine oil filler cap by
turning the filler cap clockwise until
three clicks are heard or until the cap
is fully seated.

Checking the Engine Coolant
When the engine is cold, check the
concentration and level of the engine
coolant at the intervals listed in the
scheduled maintenance information. See
Scheduled Maintenance (page 438).
Note: Make sure that the coolant level is
between the MIN and MAX marks on the
coolant reservoir.
Note: Coolant expands when it is hot. The
level may extend beyond the MAX mark.
Note: If the level is at the MIN mark, below
the MIN mark, or empty, add coolant
immediately. See Adding Engine Coolant
in this chapter.
Maintain coolant concentration within
48% to 50%, which equates to a freeze
point between -30°F (-34°C) and -34°F
(-37°C).

ENGINE COOLANT CHECK

Note: For best results, coolant
concentration should be tested with a
refractometer such as Rotunda tool
300-ROB75240 available from your
authorized dealer. Ford does not
recommend the use of hydrometers or
coolant test strips for measuring coolant
concentrations.

WARNINGS
Do not add engine coolant when the
engine is hot. Steam and scalding
liquids released from a hot cooling
system can burn you badly. Also, spilling
coolant on hot engine parts can burn you.
Do not put engine coolant in the
windshield washer fluid container. If
sprayed on the windshield, engine
coolant could make it difficult to see
through the windshield.

Note: Automotive fluids are not
interchangeable. Do not use engine coolant,
antifreeze or windshield washer fluid outside
of its specified function and vehicle location.

241

F150 (TF6) , enUSA

Maintenance
Adding Engine Coolant

•
•

Note: Do not use stop leak pellets, cooling
system sealants or additives as they can
cause damage to the engine cooling or
heating systems. Your warranty may not
cover these damages.

Alcohol and other liquids can cause engine
damage from overheating or freezing.
Do not add extra inhibitors or additives to
the coolant. These can be harmful and
compromise the corrosion protection of
the engine coolant.

Note: During normal vehicle operation, the
engine coolant may change color from
orange to pink or light red. As long as the
engine coolant is clear and uncontaminated,
this color change does not indicate that the
engine coolant has degraded, nor does it
require that you drain the engine coolant,
flush the system or replace the engine
coolant.

When adding coolant:
1.

Unscrew the cap slowly. Any pressure
will escape as you unscrew the cap.
2. Add prediluted engine coolant meeting
the Ford specification. See Capacities
and Specifications (page 296).
3. Check the coolant level in the coolant
reservoir the next few times you drive
your vehicle.
4. If necessary, add enough prediluted
engine coolant to bring the coolant
level to the proper level.

Do not mix different colors or types of
coolant in your vehicle. Mixing of engine
coolants may harm your engine’s cooling
system. The use of an improper coolant
may harm engine and cooling system
components and may void the warranty.
Use prediluted engine coolant meeting the
Ford specification. See Capacities and
Specifications (page 296).

Recycled Engine Coolant

In case of emergency, you can add a large
amount of water without engine coolant
in order to reach a vehicle service location.
In this instance, qualified personnel:

Ford Motor Company does not recommend
the use of recycled engine coolant since a
Ford-approved recycling process is not yet
available.

1. Must drain the cooling system.
2. Chemically clean the coolant system
with Motorcraft Premium Cooling
System Flush.
3. Refill with engine coolant as soon as
possible.

Used engine coolant should be disposed
of in an appropriate manner. Follow your
community’s regulations and standards
for recycling and disposing of automotive
fluids.

Water alone, without engine coolant, can
cause engine damage from corrosion,
overheating or freezing.
Do not use the following as a coolant
substitute:
• Alcohol.
• Methanol.

242

F150 (TF6) , enUSA

Brine.
Any engine coolant mixed with alcohol
or methanol antifreeze or coolant.

Maintenance
Severe Climates

the service engine soon indicator
will illuminate.

If you drive in extremely cold climates:
• It may be necessary to have a Ford
authorized dealer increase the coolant
concentration above 50%.
• A coolant concentration of 60%
provides improved freeze point
protection. Engine coolant
concentrations above 60% decrease
the overheat protection characteristics
of the engine coolant and may cause
engine damage.

If the engine reaches a preset
over-temperature condition, the engine
automatically switches to alternating
cylinder operation. Each disabled cylinder
acts as an air pump and cools the engine.
When this occurs, your vehicle will still
operate. However:
• The engine power will be limited.
• This will disable the air conditioning
system.

If you drive in extremely hot climates:
• It may be necessary to have a Ford
authorized dealer decrease the coolant
concentration to 40%.
• A coolant concentration of 40%
provides improved overheat protection.
Engine coolant concentrations below
40% will decrease the corrosion or
freeze protection characteristics of the
engine coolant and may cause engine
damage.

Continued operation increases the engine
temperature, causing the engine to shut
down completely. Your steering and
braking effort increases in this situation.
Once the engine temperature cools, the
engine can be re-started. Take your vehicle
to an authorized dealer as soon as possible
to minimize engine damage.
When Fail-Safe Mode Is Activated
WARNINGS
Fail-safe mode is for use during
emergencies only. Operate your
vehicle in fail-safe mode only as long
as necessary to bring your vehicle to rest
in a safe location and seek immediate
repairs. When in fail-safe mode, your
vehicle will have limited power, will not be
able to maintain high-speed operation, and
may completely shut down without
warning, potentially losing engine power,
power steering assist, and power brake
assist, which may increase the possibility
of a crash resulting in serious injury.

Vehicles driven year-round in non-extreme
climates should use prediluted engine
coolant for optimum cooling system and
engine protection.

What You Should Know About FailSafe Cooling
If you deplete the engine coolant supply,
fail-safe cooling allows you to temporarily
drive your vehicle before you incur
incremental component damage. The
fail-safe distance depends on ambient
temperatures, vehicle load and terrain.

Never remove the coolant reservoir
cap while the engine is running or hot.

How Fail-Safe Cooling Works
If the engine begins to overheat, the engine
coolant temperature gauge will move to
the red (hot) area and:
the coolant temperature
warning light will illuminate

243

F150 (TF6) , enUSA

Maintenance
You have limited engine power when in the
fail-safe mode, so drive your vehicle with
caution. Your vehicle will not maintain
high-speed operation and the engine will
operate poorly.

At this time, you may notice your engine
coolant temperature gauge needle move
toward the H and the POWER REDUCED
TO LOWER TEMP message may appear
in the information display.

Remember that the engine is capable of
automatically shutting down to prevent
engine damage. In this situation:

You may notice a reduction in vehicle
speed caused by reduced engine power.
In order to manage the engine fluid
temperatures, your vehicle may enter this
mode if certain high-temperature and
high-load conditions take place. The
amount of speed reduction depends on
many factors such as vehicle loading,
towing, grade and ambient temperature.
If this occurs, there is no need to pull off
the road. You can continue to drive your
vehicle while this message is active.

Pull off the road as soon as safely
possible and switch off the engine.
2. Tow your vehicle to an authorized
dealer.
3. If this is not possible, wait a short
period for the engine to cool.
4. Check the coolant level and add if low.
5. Re-start the engine and drive your
vehicle to an authorized dealer.
Note: Driving your vehicle without repair
increases the chance of engine damage. See
an authorized dealer as soon as possible.

The air conditioning may also cycle on and
off during severe operating conditions to
protect overheating of the engine. When
the engine coolant temperature decreases
to a normal operating temperature, the air
conditioning will turn on once again.

Engine Fluid Temperature
Management (If Equipped)

If the engine coolant temperature gauge
moves fully into the red (hot) area, or if the
coolant temperature warning or service
engine soon messages appear in your
information display:

WARNINGS
To reduce the risk of collision and
injury, be prepared that the vehicle
speed may reduce and the vehicle
may not be able to accelerate with full
power until the fluid temperatures reduce.

Pull off the road as soon as safely
possible and shift the transmission into
P.
2. Leave the engine running until the
coolant temperature gauge needle
moves away from the red (hot) area.
After several minutes, if the
temperature does not drop, follow the
remaining steps.
3. Switch the engine off and wait for it to
cool before checking the coolant level.
4. If the coolant level is normal, restart
your engine and continue.

Never remove the coolant reservoir
cap while the engine is running or hot.
Your vehicle can pull a trailer, but because
of the added load, your vehicle’s engine
may temporarily reach higher
temperatures during severe operating
conditions such as ascending a long or
steep grade while pulling a trailer in high
temperatures.

244

F150 (TF6) , enUSA

Maintenance
5. If the coolant is low, add coolant, and
restart the engine. See Adding Engine
Coolant or How Fail-Safe Cooling
Works in this chapter for more
information.

TRANSFER CASE FLUID
CHECK

AUTOMATIC TRANSMISSION
FLUID CHECK
Note: Transmission fluid should be checked
by an authorized dealer. If required, fluid
should be added by an authorized dealer.
The automatic transmission does not have
a transmission fluid dipstick.
Refer to your scheduled maintenance
information for scheduled intervals for fluid
checks and changes. Your transmission
does not consume fluid. However, the fluid
level should be checked if the transmission
is not working properly, (i.e., if the
transmission slips or shifts slowly) or if you
notice some sign of fluid leakage.
Do not use supplemental transmission
fluid additives, treatments or cleaning
agents. The use of these materials may
affect transmission operation and result
in damage to internal transmission
components.

E170444

1. Clean the area around the filler plug.
2. Remove the filler plug.
3. Inspect the fluid level. The fluid level
should be within 0.40 in (10mm) from
the bottom of the hole.
4. Add fluid through the filler opening, fill
to the bottom of the opening.
Use only fluid that meets Ford
specifications. Refer to the See
Capacities and Specifications (page
296).

245

F150 (TF6) , enUSA

Maintenance
WASHER FLUID CHECK

BRAKE FLUID CHECK
Fluid levels between the MIN and MAX
lines are within the normal operating range;
there is no need to add fluid. If the fluid
levels are outside of the normal operating
range, the performance of the system
could be compromised; seek service from
your authorized dealer immediately.

WARNING
If you operate your vehicle in
temperatures below 40°F (5°C), use
washer fluid with antifreeze
protection. Failure to use washer fluid with
antifreeze protection in cold weather could
result in impaired windshield vision and
increase the risk of injury or accident.

POWER STEERING FLUID
CHECK

Add fluid to fill the reservoir if the level is
low. Only use a washer fluid that meets
Ford specifications. See Capacities and
Specifications (page 296).

3.5L, 3.7L and 5.0L Engines
Your vehicle is equipped with an electric
power steering (EPS) system. There is no
fluid reservoir to check or fill.

State or local regulations on volatile
organic compounds may restrict the use
of methanol, a common windshield washer
antifreeze additive. Washer fluids
containing non-methanol antifreeze
agents should be used only if they provide
cold weather protection without damaging
the vehicle’s paint finish, wiper blades or
washer system.

6.2L Engines
Check the power steering fluid. Refer to
See Scheduled Maintenance (page 438).
1.

2.
3.
4.

Start the engine and let it run until it
reaches normal operating temperature
(the engine coolant temperature gauge
indicator will be near the center of the
normal area betweenH and C).
While the engine idles, turn the steering
wheel left and right several times.
Turn the engine off.
Check the fluid level in the reservoir. It
should be between the MIN and MAX
lines. Do not add fluid if the level is in
this range.
If the fluid is low, add fluid in small
amounts, continuously checking the
level until it reaches the range between
the MIN and MAX lines. For the proper
fluid type, See Capacities and
Specifications (page 296).
Put the cap back on the reservoir.

FUEL FILTER
Your vehicle is equipped with a lifetime
fuel filter that is integrated with the fuel
tank. Regular maintenance or replacement
is not needed.

CHANGING THE 12V BATTERY
WARNINGS
Batteries normally produce explosive
gases that can cause personal injury.
Therefore, do not allow flames,
sparks or lighted substances to come near
the battery. When working near the
battery, always shield your face and
protect your eyes. Always provide proper
ventilation.

246

F150 (TF6) , enUSA

Maintenance
WARNINGS
This vehicle may be equipped with
more than one battery, removal of
cable from only one battery does not
disconnect your vehicle electrical system.
Be sure to disconnect cables from all
batteries when disconnecting power.
Failure to do so may cause serious
personal injury or property damage.

For longer, trouble-free operation, keep the
top of the battery clean and dry. Also,
make certain the battery cables are always
tightly fastened to the battery terminals.

When lifting a plastic-cased battery,
excessive pressure on the end walls
could cause acid to flow through the
vent caps, resulting in personal injury and
damage to the vehicle or battery. Lift the
battery with a battery carrier or with your
hands on opposite corners.

It is recommended that the negative
battery cable terminal be disconnected
from the battery if you plan to store your
vehicle for an extended period of time.

If you see any corrosion on the battery or
terminals, remove the cables from the
terminals and clean with a wire brush. You
can neutralize the acid with a solution of
baking soda and water.

Because your vehicle’s engine is
electronically controlled by a computer,
some control conditions are maintained
by power from the battery. When the
battery is disconnected or a new battery
is installed, the engine must relearn its idle
and fuel trim strategy for optimum
driveability and performance. Flexible fuel
vehicles (FFV) must also relearn the
ethanol content of the fuel for optimum
driveability and performance. To begin this
process:

Keep batteries out of reach of
children. Batteries contain sulfuric
acid. Avoid contact with skin, eyes or
clothing. Shield your eyes when working
near the battery to protect against possible
splashing of acid solution. In case of acid
contact with skin or eyes, flush
immediately with water for a minimum of
15 minutes and get prompt medical
attention. If acid is swallowed, call a
physician immediately.

1.
2.

Note: If your battery has a cover/shield,
make sure it is reinstalled after the battery
has been cleaned or replaced.

Note: Battery posts, terminals and related
accessories contain lead and lead
compounds. Wash hands after handling.

Note: Electrical or electronic accessories
or components added to your vehicle by the
dealer or the owner may adversely affect
battery performance and durability.

Your vehicle is equipped with a Motorcraft
maintenance-free battery which normally
does not require additional water during
its life of service.

247

F150 (TF6) , enUSA

With your vehicle at a complete stop,
set the parking brake.
Put the gearshift in P(Park), turn off all
accessories.
Start the engine. Run the engine until
it reaches normal operating
temperature.
Allow the engine to idle for at least one
minute.
Turn the air conditioning on and allow
the engine to idle for at least one
minute.

Maintenance
6. Release the parking brake. With your
foot on the brake pedal and with the
air conditioning on, put your vehicle in
D (Drive) and allow the engine to idle
for at least one minute.
• If you do not allow the engine to
relearn its idle trim, the idle quality
of your vehicle may be adversely
affected until the idle trim is
eventually relearned.
7. Drive your vehicle to complete the
relearning process
• Your vehicle may need to be driven
10 miles (16 kilometers) or more to
relearn the idle and fuel trim
strategy along with the ethanol
content for flexible fuel vehicles.
• For flexible fuel vehicles, if you are
operating on E85, you may
experience poor starts or an
inability to start the engine and
driveability problems until the fuel
trim and ethanol content have been
relearned.

control fan, heated steering wheel, audio
and navigation system. A message may be
shown in the information displays to alert
the driver that battery protection actions
are active. These messages are only for
notification that an action is taking place,
and not intended to indicate an electrical
problem or that the battery requires
replacement.
Electrical accessory installation
To ensure proper operation of the Battery
Management System, any electrical
devices that are added to your vehicle
should not have their ground connection
made directly at the negative battery post.
A connection at the negative battery post
can cause inaccurate measurements of
the battery condition and potential
incorrect system operation.
Note: Electrical or electronic accessories
added to your vehicle by the dealer or the
owner, may adversely affect battery
performance and durability, and may affect
the performance of other electrical systems
in your vehicle.

If the battery has been disconnected or a
new battery has been installed, the clock
and radio settings must be reset once the
battery is reconnected.

When a battery replacement is required,
the battery should only be replaced with
a Ford-recommended replacement battery
that matches the electrical requirements
of your vehicle. After battery replacement,
or in some cases after charging the battery
with the external charger, the Battery
Management System requires eight hours
of vehicle sleep time (key off with doors
closed) to relearn the new battery state of
charge. Prior to relearning the state of
charge, the Battery Management System
may disable electrical features (to protect
the battery) earlier than normal.

Always dispose of automotive
batteries in a responsible manner.
Follow your local authorized standards
for disposal. Call your local authorized
recycling center to find out more about
recycling automotive batteries.

Battery Management System (If
Equipped)
The battery management system (BMS)
monitors battery conditions and takes
actions to extend battery life. If excessive
battery drain is detected, the system may
temporarily disable certain electrical
features to protect the battery. Those
electrical accessories affected include the
rear defrost, heated/cooled seats, climate

248

F150 (TF6) , enUSA

Maintenance
CHECKING THE WIPER
BLADES

A
E165794

E142463

2. Release the wiper blade lock (A) and
separate the wiper blade from the
wiper arm.
3. Install in the reverse order.
Note: Make sure that the wiper blade locks
into place. Lower the wiper arm and blade
back on the windshield. The wiper arms will
automatically return to their normal position
when you turn the ignition on.

Run the tip of your fingers over the edge of
the blade to check for roughness.
Clean the wiper blades with washer fluid
or water applied with a soft sponge or
cloth.

CHANGING THE WIPER
BLADES

•

You can manually move the wiper arms
when the ignition is off. This allows for ease
of blade replacement and cleaning under
the blades.

•

Replace wiper blades at least once per
year for optimum performance.
You can improve poor wiper quality by
cleaning the wiper blades and the
windshield.

ADJUSTING THE HEADLAMPS
Vertical Aim Adjustment
The headlamps on your vehicle are
properly aimed at the assembly plant. If
your vehicle has been in an accident, have
the alignment of your headlamps checked
by your authorized dealer.
E165804

Pull the wiper blade and arm away
from the glass.

249

F150 (TF6) , enUSA

Maintenance
Headlamp Aiming Target

E167358

4. For vehicles with halogen
headlamps: on the wall or screen you
will observe a light pattern with a
distinct horizontal edge toward the
right. If this edge is not at the horizontal
reference line, you will need to adjust
the beam so the edge is at the same
height as the horizontal reference line.

E142592

8 feet (2.4 meters)

Center height of lamp to ground

25 feet (7.6 meters)

Horizontal reference line

Vertical Aim Adjustment
1.

Park the vehicle directly in front of a
wall or screen on a level surface,
approximately 25 feet (7.6 meters)
away.
2. Measure the height from the center of
your headlamp (indicated by a 3.0
millimeter circle on the lens) to the
ground and mark an 8 foot (2.4 meter)
horizontal reference line on the vertical
wall or screen at this height (a piece of
masking tape works well).
Note: To see a clearer light pattern for
adjusting, you may want to block the light
from one headlamp while adjusting the
other.

E163806

5. Locate the vertical adjuster on each
headlamp. Use a #2 Phillips
screwdriver to turn the adjuster either
counterclockwise or clockwise in order
to adjust the vertical aim of the
headlamp.

3. Turn on the low beam headlamps to
illuminate the wall or screen and open
the hood. Cover one of the headlamps
so no light hits the wall.

250

F150 (TF6) , enUSA

Maintenance
REMOVING A HEADLAMP
WARNING
Handle a halogen headlamp bulb
carefully and keep out of children’s
reach. Grasp the bulb only by its
plastic base and do not touch the glass.
The oil from your hand could cause the
bulb to break the next time the headlamps
are operated.
E142465

Note: If the bulb is accidentally touched,
clean it with rubbing alcohol before
installing it.

6. For vehicles with HID headlamps:
there is a distinct cut-off (change from
light to dark) in the left portion of the
beam pattern. Position the top edge of
this cut-off 2 inches (5 centimeters)
below the horizontal reference line.

Note: This procedure is for replacing the
headlamps, park lamps, turn lamps or side
marker lamps.

Replacing Halogen Headlamp
Bulbs (If Equipped)
1.

Make sure the headlamp control is in
the off position and open the hood.

E167359

Locate the vertical adjuster on each
headlamp. Use a Phillips #2
screwdriver to turn the adjuster either
clockwise or counterclockwise to
adjust the vertical aim of the
headlamp. The horizontal edge of the
brighter light should touch the
horizontal reference line.
8. Repeat Steps 3 through 7 to adjust the
other headlamp.
9. Close the hood and turn off the lamps.

E167360

2. Remove the pushpin that holds the air
deflector or protective cover to the
upper inboard corner of the lamp.

Horizontal Aim Adjustment
Horizontal aim is not required for this
vehicle and is not adjustable.

251

F150 (TF6) , enUSA

Maintenance

E167363

E167361

3. Loosen the three retaining bolts (two
at the top of the lamp, one at the lower
inboard corner).
4. Once the three retaining bolts are
removed, slide the headlamp assembly
forward, disconnecting the two snap
attachments at the fender.
5. Disconnect the electrical connector
from the bulb by pulling rearward.

For the park lamp, turn lamp or side
marker lamp bulbs, disconnect the
electrical connector from the bulb by
pulling rearward, then remove the bulb
by turning it counterclockwise and
pulling it straight out.
8. Install the new bulb(s) in reverse order.

Replacing HID Headlamp Bulbs (If
Equipped)
The low beam headlamps on your vehicle
use a high intensity discharge source.
These lamps operate at a high voltage.
When you have a burned out bulb, you
must have the bulb and starter capsule
assembly replaced by an authorized dealer.

CHANGING A BULB
Lamp Assembly Condensation

E167362

Exterior lamps are vented to
accommodate normal changes in pressure.
Condensation can be a natural by-product
of this design. When moist air enters the
lamp assembly through the vents, there is
a possibility that condensation can occur
when the temperature is cold. When
normal condensation occurs, a thin film of
mist can form on the interior of the lens.
The thin mist eventually clears and exits
through the vents during normal operation.
Clearing time may take as long as 48 hours
under dry weather conditions.

6. Remove the bulb and socket by turning
it counterclockwise, then pull it straight
out.

252

F150 (TF6) , enUSA

Maintenance
Examples of acceptable condensation are:
• Presence of thin mist (no streaks, drip
marks or droplets).
• Fine mist covers less than 50% of the
lens.
Examples of unacceptable moisture
(usually caused by a lamp water leak) are:
• Water puddle inside the lamp.
• Large water droplets, drip marks or
streaks present on the interior of the
lens.

E167364

3. Remove the two bolts from the tail
lamp assembly. Then, carefully pull the
lamp assembly from the tailgate pillar
by releasing the two retaining tabs.
4. Disconnect the electrical connector
from the bulb.

Take your vehicle to a dealer for service if
any of the above conditions of
unacceptable moisture are present.

Replacing Fog Lamp Bulbs (If
Equipped

E167365

E163826

1. Make sure the headlamps are off.
2. Disconnect the electrical connector
from the fog lamp bulb.
3. Turn the bulb counterclockwise and
remove it from the fog lamp.
4. Install the new bulb in reverse order.

5. Rotate the bulb socket
counterclockwise and remove it from
the tail lamp assembly.
6. Install the new bulb in reverse order.

Replacing
Brake/Tail/Turn/Reverse Lamp
Bulbs

1. Make sure the headlamps are off.
2. Remove the two screws and move the
lamp assembly away from the vehicle
to expose the bulb sockets.

Replacing Cargo Lamp and Highmount Brake Lamp Bulbs

1. Make sure the headlamps are off.
2. Open the tailgate to access the tail
lamp assemblies

253

F150 (TF6) , enUSA

Maintenance
1.

Reach behind the rear bumper to
locate the bulb.
2. Twist the bulb socket counterclockwise
and carefully pull to remove it from the
lamp assembly.
3. Pull the bulb straight out of the socket.
4. Install the new bulb in reverse order.

Replacing exterior mounted mirror
turn signal indicator lamp bulbs
E167366

For bulb replacement, see your authorized
dealer.

3. Disconnect the electrical connector
from the bulb.
4. Remove the bulb socket by rotating it
counterclockwise and pulling it out of
the lamp assembly.
5. Pull the bulb straight out of the socket.
6. Install the new bulb in reverse order.

BULB SPECIFICATION CHART
Replacement bulbs are specified in the
chart below. Headlamp bulbs must be
marked with an authorized “D.O.T.” for
North America and an “E” for Europe to
ensure lamp performance, light brightness
and pattern and safe visibility. The correct
bulbs will not damage the lamp assembly
or void the lamp assembly warranty and
will provide quality bulb illumination time.

Replacing the License Plate Lamp
Bulb
Note: The license plate bulbs are located
behind the rear bumper.

E167368

254

F150 (TF6) , enUSA

Maintenance

Function

Number of Bulbs

Trade name

Headlamps, halogen, high
beam/low beam (if equipped)

H13/9008

Headlamps, high intensity
discharge (HID) (if equipped)

D3S

High-mount brake lamp

912

Front Park/Turn lamps

3157NAK LCP (natural amber)

Front side marker

168

Front row map lamps

W5W

Fog lamp

9140

Backup lamp

921

Rear dome/courtesy lamps

578

Rear/stop/turn/side marker

3057K LCP

License plate lamp

194

High mount cargo box lamps

912

Exterior mounted mirror turn
signal indicator (if equipped)*

LED

Puddle lamp (if equipped)*

LED

To replace all instrument panel lights - see your authorized dealer
•

See your authorized dealer to replace the bulb.

255

F150 (TF6) , enUSA

Maintenance
2. Pull up to disconnect wiring harness
(2).
3. Disconnect the sensor by pressing the
retaining tab and pulling back on the
lead.

CHANGING THE ENGINE AIR
FILTER - 3.5L ECOBOOST™
WARNING
To reduce the risk of vehicle damage
and personal burn injuries, do not
start your engine with the air cleaner
removed and do not remove it while the
engine is running.
Note: Failure to use the correct air filter
element may result in severe engine
damage. The customer warranty may be
void for any damage to the engine if the
correct air filter element is not used.

E167353

4. Clean the area around the air tube to
air cover connection to prevent debris
from entering the system, and then
loosen the bolt on the air tube clamp
so the clamp is no longer snug to the
air tube. It is not necessary to
completely remove the clamp.
5. Pull the air tube off from the air cleaner
housing.
6. Release the clamps that secure the
cover to the air filter housing. Push the
air filter cover toward the center of the
vehicle and up slightly to release it.
7. Remove the air filter element from the
air filter housing.
8. Install a new air filter element.
9. Replace the air filter housing cover and
secure the clamps. Be careful not to
crimp the filter element edges between
the air filter housing and cover and
ensure that the tabs on the edge are
properly aligned into the slots.
10. Slip the air tube onto the air filter
housing and tighten the air-tube
clamp bolt snugly, but do not
overtighten it.

When changing the air filter element, use
only the air filter element listed. See
Capacities and Specifications (page
296).
Change the air filter element at the proper
interval. See Scheduled Maintenance
(page 438).

E167352

Locate the sensor electrical connector
on the air outlet tube (1). This
connector will need to be unplugged.

256

F150 (TF6) , enUSA

Maintenance
11.
12.

Reconnect the sensor electrical
connector to the outlet tube.
Push the wiring harness back in place.

Locate the mass air flow sensor
electrical connector on the air outlet
tube. Disconnect the Mass Air Flow
(MAF) sensor electrical connector.

CHANGING THE ENGINE AIR
FILTER - 3.7L/5.0L/6.2L
WARNING
To reduce the risk of vehicle damage
and personal burn injuries, do not
start your engine with the air cleaner
removed and do not remove it while the
engine is running.
E163756

Note: Failure to use the correct air filter
element may result in severe engine
damage. The customer warranty may be
void for any damage to the engine if the
correct air filter element is not used.

2. Reposition the locking clip on the
connector (connector shown from
below for clarity), squeeze the
connector and pull it off of the air
outlet tube.

Note: For EcoBoost equipped vehicles:
When servicing the air cleaner, it is
important that no foreign material enter the
air induction system. The engine and
turbocharger are susceptible to damage
from even small particles.
When changing the air filter element, use
only the air filter element listed. See
Capacities and Specifications (page
296).
Change the air filter element at the proper
interval. See Scheduled Maintenance
(page 438).

E163757

3. Clean the area around the air tube to
air cover connection to prevent debris
from entering the system and then
loosen the bolt on the air tube clamp
so the clamp is no longer snug to the
air tube. It is not necessary to
completely remove the clamp.
4. Pull the air tube off from the air cleaner
housing.

E163755

257

F150 (TF6) , enUSA

Maintenance

E163758

E163760

5. Release the three clamps that secure
the cover to the air filter housing. Push
the air filter cover toward the center of
the vehicle and up slightly to release it.
6. Remove the air filter element from the
air filter housing.
7. Install a new air filter element.

10.

E163759

8. Replace the air filter housing cover and
secure the clamps. Be careful not to
crimp the filter element edges between
the air filter housing and cover and
ensure that the tabs on the edge are
properly aligned into the slots.
9. Slip the air tube onto the air filter
housing and tighten the air-tube clamp
bolt snugly, but do not overtighten it.

258

F150 (TF6) , enUSA

Reconnect the mass air flow sensor
electrical connector to the outlet
tube. Make sure the locking tab on
the connector is in the “locked”
position (connector shown from
below for clarity).

Vehicle Care
GENERAL INFORMATION

CLEANING THE EXTERIOR

Your Ford or Lincoln authorized dealer has
many quality products available to clean
your vehicle and protect its finishes.

Wash your vehicle regularly with cool or
lukewarm water and a neutral pH
shampoo, such as Motorcraft Detail Wash.
•

CLEANING PRODUCTS
For best results, use the following products
or products of equivalent quality:
• Motorcraft Bug and Tar Remover
(ZC-42)
• Motorcraft Custom Bright Metal
Cleaner (ZC-15)
• Motorcraft Detail Wash (ZC-3-A)
• Motorcraft Dusting Cloth (ZC-24)
• Motorcraft Engine Shampoo and
Degreaser (U.S. only) (ZC-20)
• Motorcraft Engine Shampoo (Canada
only) (CXC-66-A)
• Motorcraft Multi-Purpose Cleaner
(Canada only) (CXC-101)
• Motorcraft Premium Glass Cleaner
(Canada only) (CXC-100)
• Motorcraft Premium Quality
Windshield Washer Fluid (Canada
only) [CXC-37-(A, B, D or F)]
• Motorcraft Premium Windshield Wash
Concentrate with Bitterant (U.S. only)
(ZC-32-B2)
• Motorcraft Professional Strength
Carpet & Upholstery Cleaner (ZC-54)
• Motorcraft Spot and Stain Remover
(U.S. only) (ZC-14)
• Motorcraft Ultra-Clear Spray Glass
Cleaner (ZC-23)
• Motorcraft Wheel and Tire Cleaner
(ZC-37-A)

•

Never use strong household detergents
or soap, such as dish washing or
laundry liquid. These products can
discolor and spot painted surfaces.
Never wash a vehicle that is “hot to the
touch” or during exposure to strong,
direct sunlight.
Dry your vehicle with a chamois or soft
terry cloth towel in order to eliminate
water spotting.
Immediately remove items such as
gasoline, diesel fuel, bird droppings and
insect deposits because they can cause
damage to your vehicle’s paintwork
and trim over time. Use Motorcraft Bug
and Tar Remover.
Remove any exterior accessories, such
as antennas, before entering a car
wash.

Note: Suntan lotions and insect repellents
can damage any painted surface; if these
substances come in contact with your
vehicle, wash off as soon as possible.

Stripes or Graphics (if equipped)
Do not use a commercial or high-pressure
sprayer on the surface or edge of stripes
and graphics. This can cause damage to
the film and cause the edge of the film to
peel away from the vehicle surface.

Exterior Chrome
Note: Never use abrasive materials such as
steel wool or plastic pads as they can
scratch the chrome surface.
Note: Do not use chrome cleaner, metal
cleaner or polish on wheels and wheel
covers

259

F150 (TF6) , enUSA

Vehicle Care
•

•

Wash your vehicle first, using cool or
lukewarm water and a neutral pH
shampoo, such as Motorcraft Detail
Wash.
Use Motorcraft Custom Bright Metal
Cleaner. Apply the product as you
would a wax to clean bumpers and
other chrome parts; allow the cleaner
to dry for a few minutes, then wipe off
the haze with a clean, dry rag.

•
•
•
•

Do not apply cleaning product to hot
surfaces and do not leave cleaning
product on chrome surfaces longer
than the time recommended.
Using other non-recommended
cleaners can result in severe and
permanent cosmetic damage.

Underbody

•
•

Flush the complete underside of your
vehicle frequently. Keep body and door
drain holes free from packed dirt.

Cleaning Plastic Exterior Parts

CLEANING THE ENGINE

Use only approved products to clean
plastic parts
•
•

Engines are more efficient when they are
clean because grease and dirt buildup keep
the engine warmer than normal.

For routine cleaning, use Motorcraft
Detail Wash.
If tar or grease spots are present, use
Motorcraft Bug and Tar Remover.

When washing:
• Take care when using a power washer
to clean the engine. The high-pressure
fluid could penetrate the sealed parts
and cause damage.
• Do not spray a hot engine with cold
water to avoid cracking the engine
block or other engine components.
• Spray Motorcraft Engine Shampoo and
Degreaser on all parts that require
cleaning and pressure rinse clean. In
Canada, use Motorcraft Engine
Shampoo.
• Never wash or rinse the engine while it
is hot or running; water in the running
engine may cause internal damage.

WAXING
Regular waxing is necessary to protect your
car's paint from the elements. We
recommend that you wash and wax the
painted surface once or twice a year.
When washing and waxing, park your
vehicle in a shaded area out of direct
sunlight. Always wash your vehicle before
applying wax.

260

F150 (TF6) , enUSA

Use a quality wax that does not contain
abrasives.
Follow the manufacturer’s instructions
to apply and remove the wax.
Apply a small amount of wax in a
back-and-forth motion, not in circles.
Do not allow wax to come in contact
with any non-body (low-gloss black)
colored trim. The wax will discolor or
stain the parts over time.
• Roof racks.
• Bumpers.
• Grained door handles.
• Side moldings.
• Mirror housings.
• Windshield cowl area.
Do not apply wax to glass areas.
After waxing, your car's paint should
feel smooth, and be free of streaks and
smudges.

Vehicle Care
•

•

Never wash or rinse any ignition coil,
spark plug wire or spark plug well, or
the area in and around these locations.
Cover the battery, power distribution
box, and air filter assembly to prevent
water damage when cleaning the
engine.

WARNINGS
On vehicles equipped with
seat-mounted airbags, do not use
chemical solvents or strong
detergents. Such products could
contaminate the side airbag system and
affect performance of the side airbag in a
collision.

CLEANING THE WINDOWS AND
WIPER BLADES

For fabric, carpets, cloth seats, safety belts
and seats equipped with side airbags:
• Remove dust and loose dirt with a
vacuum cleaner.
• Remove light stains and soil with
Motorcraft Professional Strength
Carpet & Upholstery Cleaner.

Car wash chemicals and environmental
fallout can result in windshield and wiper
blade contamination. Dirty windshield and
wipers will result in poor windshield wiper
operation. Keep the windshield and wiper
blades clean to maintain windshield wiper
performance.

•

To clean the windshield and wiper blades:
• Clean the windshield with a
non-abrasive glass cleaner.
• For windshields contaminated with
tree sap, chemicals, wax or bugs, clean
the entire windshield using steel wool
(no greater than 0000 grade) in a
circular motion and rinse with water.
• Clean the wiper blades with isopropyl
rubbing alcohol or windshield washer
fluid.

•

Note: Do not use razor blades or other
sharp objects to clean or remove decals
from the inside of the heated rear window.
The vehicle warranty does not cover
damage caused to the heated rear window
grid lines.

CLEANING THE INSTRUMENT
PANEL AND INSTRUMENT
CLUSTER LENS
WARNING

CLEANING THE INTERIOR

Do not use chemical solvents or
strong detergents when cleaning the
steering wheel or instrument panel
to avoid contamination of the airbag
system.

WARNINGS
Do not use cleaning solvents, bleach
or dye on the vehicle’s safety belts,
as these actions may weaken the
belt webbing.

261

F150 (TF6) , enUSA

If grease or tar is present on the
material, spot-clean the area first with
Motorcraft Spot and Stain Remover. In
Canada, use Motorcraft Multi-Purpose
Cleaner.
If a ring forms on the fabric after spot
cleaning, clean the entire area
immediately (but do not oversaturate)
or the ring will set.
Do not use household cleaning
products or glass cleaners, which can
stain and discolor the fabric and affect
the flame retardant abilities of the seat
materials.

Vehicle Care
Clean the instrument panel and cluster
lens with a clean, damp, white cotton
cloth, then use a clean and dry white
cotton cloth to dry these areas.
•

•

4. Remove the soaked cloth and if it is not
soiled badly, use this cloth to clean the
area by using a rubbing motion for 60
seconds.
5. Following this, wipe area dry with a
clean, white, cotton cloth.

Avoid cleaners or polishes that increase
the gloss of the upper portion of the
instrument panel. The dull finish in this
area helps protect you from
undesirable windshield reflection.
Be certain to wash or wipe your hands
clean if you have been in contact with
certain products such as insect
repellent and suntan lotion in order to
avoid possible damage to the interior
painted surfaces.
Do not use household or glass cleaners
as these may damage the finish of the
instrument panel, interior trim and
cluster lens.
Do not allow air fresheners and hand
sanitizers to spill onto interior surfaces.
If a spill occurs, wipe off immediately.
Damage may not be covered by your
warranty.

CLEANING LEATHER SEATS (IF
EQUIPPED)

WITHOUT THE KING RANCH
EDITION
For routine cleaning, wipe the surface with
a soft, damp cloth. For more thorough
cleaning, wipe the surface with a mild soap
and water solution. Dry the area with a soft
cloth.
If you cannot completely clean the leather
using a mild soap and water solution, you
can try a commercially available leather
cleaning product designed for automotive
interiors.
Note: To check for compatibility, first test
any cleaner or stain remover on an
inconspicuous part of the leather.

If a staining liquid like coffee or juice has
been spilled on the instrument panel or on
interior trim surfaces, clean as follows:

You should:

Wipe up spilled liquid using a clean,
white, cotton cloth.
2. Wipe the surface with a damp, clean,
white cotton cloth. For more thorough
cleaning, use a mild soap and water
solution. If the spot cannot be
completely cleaned by this method,
the area may be cleaned using a
commercially available cleaning
product designed for automotive
interiors.
3. If necessary, apply more soap and
water solution or cleaning product to
a clean, white, cotton cloth and press
the cloth onto the soiled area. Allow
this to set at room temperature for 30
minutes.

•
•
•

Do not use the following products as these
may damage the leather:
•
•

262

F150 (TF6) , enUSA

remove dust and loose dirt with a
vacuum cleaner
clean spills and stains as quickly as
possible
Check for compatibility, first test any
cleaner or stain remover on an
inconspicuous part of the leather.

oil/petroleum-based leather
conditioners
household cleaners

Vehicle Care
•
•

alcohol solutions
solvents or cleaners intended
specifically for rubber, vinyl and
plastics.

In order to lessen the appearance of
certain scratches and other wear marks,
apply conditioner on the affected area
following the same instructions as in the
Conditioning section.

WITH THE KING RANCH EDITION

Conditioning

Your vehicle is equipped with seating
covered in premium, top-grain leather
which is extremely durable, but still
requires special care and maintenance in
order to preserve longevity and comfort.

Bottles of King Ranch Leather Conditioner
are available at the King Ranch Saddle
Shop. Visit the website at
www.krsaddleshop.com, or telephone (in
the United States) 1–800–282–KING
(5464). If you are unable to obtain King
Ranch Leather Conditioner, use another
premium leather conditioner.

Regular cleaning and conditioning will
maintain the appearance of the leather.
Cleaning

•

For dirt, use a vacuum cleaner then use a
clean, damp cloth or soft brush.

•

For routine cleaning, wipe the surface with
a soft, damp cloth. For more thorough
cleaning, wipe the surface with a mild soap
and water solution.
•
•

•

Clean spills as quickly as possible.
Test any cleaner or stain remover on
an inconspicuous part of the leather as
cleaners may darken the leather.
Do not spill coffee, ketchup, mustard,
orange juice or oil-based products on
the leather as they may permanently
stain the leather.
Do not use household cleaning
products, alcohol solutions, solvents
or cleaners intended for rubber, vinyl
or plastics.

REPAIRING MINOR PAINT
DAMAGE
Authorized dealers have touch-up paint to
match your vehicle’s color. Your vehicle
color code is printed on a sticker on the
front, left-hand side door jamb. Take your
color code to your authorized dealer to
make sure you get the correct color.

Scratches

Before repairing minor paint damage, use
a cleaner such as Motorcraft Bug and Tar
Remover to remove particles such as bird
droppings, tree sap, insect deposits, tar
spots, road salt and industrial fallout.

Natural Markings - Because the leather in
the seat comes from genuine steer hides,
there will be evidence of naturally
occurring markings, such as small scars.
These markings give character to the
seating covers and considered to be proof
of a genuine leather product.

Always read the instructions before using
cleaning products.

263

F150 (TF6) , enUSA

Clean the surfaces using the steps
outlined in the Cleaning section.
Make sure the leather is dry then apply
a nickel-sized amount of conditioner
to a clean, dry cloth.
Rub the conditioner into the leather
until it disappears. Allow the
conditioner to dry, then repeat the
process for the entire interior. If a film
appears, wipe it off with a dry, clean
cloth.

Vehicle Care
CLEANING THE ALLOY
WHEELS (IF EQUIPPED)

VEHICLE STORAGE
If you plan on storing your vehicle for an
extended period of time (30 days or more),
read the following maintenance
recommendations to make sure your
vehicle stays in good operating condition.

Note: Do not apply a cleaning chemical to
warm or hot wheel rims and covers.
Note: Some automatic car washes may
cause damage to the finish on your wheel
rims and covers.

All motor vehicles and their components
were engineered and tested for reliable,
regular driving. Long term storage under
various conditions may lead to component
degradation or failure unless specific
precautions are taken to preserve the
components.

Note: Industrial-strength or heavy-duty
cleaners in combination with brush agitation
to remove brake dust and dirt, could wear
away the clear coat finish over a period time.
Note: Do not use hydrofluoric acid-based
or high caustic-based wheel cleaners, steel
wool, fuels or strong household detergents.

General
•

Note: If you intend parking your vehicle for
an extended period after cleaning the
wheels with a wheel cleaner, drive your
vehicle for a few minutes before doing so.
This will reduce the risk of increased
corrosion of the brake discs.

•
•

Alloy wheels and wheel covers are coated
with a clear coat paint finish. To maintain
their condition we recommend that you:
•

•

Body
•

Clean the wheels weekly using
Motorcraft Wheel and Tire Cleaner.
Apply using manufacturer's
instructions.
Use a sponge to remove heavy
deposits of dirt and brake dust
accumulation.
Rinse thoroughly with a strong stream
of water when you have completed the
cleaning process.
To remove tar and grease, use
Motorcraft Bug and Tar Remover.

•
•
•

•

•
•

264

F150 (TF6) , enUSA

Store all vehicles in a dry, ventilated
place.
Protect from sunlight, if possible.
If vehicles are stored outside, they
require regular maintenance to protect
against rust and damage.

Wash your vehicle thoroughly to
remove dirt, grease, oil, tar or mud from
exterior surfaces, rear-wheel housing
and underside of front fenders.
Periodically wash your vehicle stored
in exposed locations.
Touch-up exposed or primed metal to
prevent rust.
Cover chrome and stainless steel parts
with a thick coat of auto wax to prevent
discoloration. Re-wax as necessary
when your vehicle is washed.
Lubricate all hood, door and trunk lid
hinges, and latches with a light grade
oil.
Cover interior trim to prevent fading.
Keep all rubber parts free from oil and
solvents.

Vehicle Care
Engine

Miscellaneous

•

The engine oil and filter should be
changed prior to storage, as used
engine oil contain contaminates that
may cause engine damage.
Start the engine every 15 days. Run at
fast idle until it reaches normal
operating temperature
With your foot on the brake, shift
through all the gears while the engine
is running.

•

Removing Vehicle From Storage
When your vehicle is ready to come out of
storage, do the following:
• Wash your vehicle to remove any dirt
or grease film build-up on window
surfaces.
• Check windshield wipers for any
deterioration.
• Check under the hood for any foreign
material that may have collected
during storage (mice/squirrel nests).
• Check the exhaust for any foreign
material that may have collected
during storage.
• Check tire pressures and set tire
inflation per the Tire Label.
• Check brake pedal operation. Drive
your vehicle 15 feet (4.5 meters) back
and forth to remove rust build-up.
• Check fluid levels (including coolant,
oil and gas) to make sure there are no
leaks, and fluids are at recommended
levels.
• If the battery was removed, clean the
battery cable ends and inspect.

Fuel system
•

Fill the fuel tank with high-quality fuel
until the first automatic shutoff of the
fuel pump nozzle.

Cooling system
•
•

Protect against freezing temperatures.
When removing your vehicle from
storage, check coolant fluid level.
Confirm there are no cooling system
leaks, and fluid is at the recommended
level.

Battery
•
•

Check and recharge as necessary. Keep
connections clean.
If storing your vehicle for more than 30
days without recharging the battery, it
may be advisable to disconnect the
battery cables to ensure battery charge
is maintained for quick starting.

Note: If battery cables are disconnected, it
will be necessary to reset memory features.

Contact your authorized dealer if you have
any concerns or issues.

Brakes
•

Make sure brakes and parking brake
are fully released.

Tires
•

Maintain recommended air pressure.

265

F150 (TF6) , enUSA

Make sure all linkages, cables, levers
and pins under your vehicle are covered
with grease to prevent rust.
Move vehicles at least 25 feet (8
meters) every 15 days to lubricate
working parts and prevent corrosion.

Wheels and Tires
GENERAL INFORMATION
Notice to Owners About High
Performance Tires
Note: Your vehicle is equipped with high
performance tires. When first driving the
vehicle after it has been parked for a period
of time, you may experience a temporary
ride disturbance. This is a characteristic of
the tires and should be no reason for
concern. The condition should correct itself
within 5-15 miles (8-25 kilometers) of
driving. If the disturbance persists, have the
tires serviced by an authorized dealer.

E145298

Utility vehicles and trucks handle
differently than passenger cars in the
various driving conditions that are
encountered on streets, highways and
off-road. Utility vehicles and trucks are not
designed for cornering at speeds as high
as passenger cars any more than low-slung
sports cars are designed to perform
satisfactorily under off-road conditions.

Notice to utility vehicle and truck
owners
WARNINGS
Utility vehicles have a significantly
higher rollover rate than other types
of vehicles. To reduce the risk of
serious injury or death from a rollover or
other crash you must avoid sharp turns and
abrupt maneuvers, drive at safe speeds for
the conditions, keep tires properly inflated,
never overload or improperly load your
vehicle, and make sure every passenger is
properly restrained.

Study your owner's manual and any
supplements for specific information about
equipment features, instructions for safe
driving and additional precautions to
reduce the risk of an accident or serious
injury.

Four-wheel drive system (if
equipped)

In a rollover crash, an unbelted
person is significantly more likely to
die than a person wearing a seat belt.
All occupants must wear seat belts, and
children and infants must use appropriate
restraints to minimize the risk of injury or
ejection.

WARNING
Do not become overconfident in the
ability of four-wheel drive vehicles.
Although a four-wheel drive vehicle
may accelerate better than a two-wheel
drive vehicle in low traction situations, it
won't stop any faster than two-wheel drive
vehicles. Always drive at a safe speed.

Do not become overconfident in the
ability of four-wheel drive vehicles.
Although a four-wheel drive vehicle
may accelerate better than a two-wheel
drive vehicle in low traction situations, it
won't stop any faster than two-wheel drive
vehicles. Always drive at a safe speed.

266

F150 (TF6) , enUSA

Wheels and Tires
A vehicle equipped with four-wheel drive
(when selected) has the ability to use all
four wheels to power itself. This increases
traction which may enable you to safely
drive over terrain and road conditions that
a conventional two-wheel drive vehicle
cannot.

•

On some four-wheel drive models, the
initial shift from two-wheel drive to
four-wheel drive while the vehicle is
moving can cause a momentary clunk and
ratcheting sound. These sounds are normal
as the front drivetrain comes up to speed
and are not cause for concern.

•

How your vehicle differs from
other vehicles

Higher - to allow higher load carrying
capacity and to allow it to travel over
rough terrain without getting hung up
or damaging underbody components.
Shorter - to give it the capability to
approach inclines and drive over the
crest of a hill without getting hung up
or damaging underbody components.
All other things held equal, a shorter
wheelbase may make your vehicle
quicker to respond to steering inputs
than a vehicle with a longer wheelbase.
Narrower - to provide greater
maneuverability in tight spaces,
particularly in off-road use.

Sport utility vehicles and trucks can differ
from some other vehicles in a few
noticeable ways. Your vehicle may be:

E168583

E145299

267

F150 (TF6) , enUSA

Wheels and Tires
Tire Quality Grades apply to new
pneumatic passenger car tires.
They do not apply to deep tread,
winter-type snow tires,
space-saver or temporary use
spare tires, light truck or LT type
tires, tires with nominal rim
diameters of 10 to 12 inches or
limited production tires as defined
in Title 49 Code of Federal
Regulations Part 575.104 (c)(2).
U.S. Department of
Transportation Tire quality
grades: The U.S. Department of
Transportation requires Ford
Motor Company to give you the
following information about tire
grades exactly as the government
has written it.

As a result of the above dimensional
differences, Sport utility vehicles and
trucks often will have a higher center of
gravity and a greater difference in center
of gravity between the loaded and
unloaded condition. These differences that
make your vehicle so versatile also make
it handle differently than an ordinary
passenger car.

TIRE CARE
Information About Uniform
Tire Quality Grading

Treadwear
The treadwear grade is a
comparative rating based on the
wear rate of the tire when tested
under controlled conditions on a
specified government test course.
For example, a tire graded 150
would wear one and one-half (1
½) times as well on the
government course as a tire
graded 100. The relative
performance of tires depends
upon the actual conditions of their
use, however, and may depart
significantly from the norm due to
variations in driving habits, service
practices, and differences in road
characteristics and climate.

E142542

Tire Quality Grades apply to new
pneumatic passenger car tires.
The Quality grades can be found
where applicable on the tire
sidewall between tread shoulder
and maximum section width. For
example: Treadwear 200
Traction AA Temperature A.
These Tire Quality Grades are
determined by standards that the
United States Department of
Transportation has set.

268

F150 (TF6) , enUSA

Wheels and Tires
test wheel. Sustained high
temperature can cause the
material of the tire to degenerate
and reduce tire life, and excessive
temperature can lead to sudden
tire failure. The grade C
corresponds to a level of
performance which all passenger
car tires must meet under the
Federal Motor Vehicle Safety
Standard No. 139. Grades B and A
represent higher levels of
performance on the laboratory
test wheel than the minimum
required by law.

Traction AA A B C
WARNING
The traction grade assigned
to this tire is based on
straight-ahead braking traction
tests, and does not include
acceleration, cornering,
hydroplaning or peak traction
characteristics
The traction grades, from highest
to lowest are AA, A, B, and C. The
grades represent the tire’s ability
to stop on wet pavement as
measured under controlled
conditions on specified
government test surfaces of
asphalt and concrete. A tire
marked C may have poor traction
performance.

Glossary of Tire Terminology
*Tire label: A label showing the
original equipment tire sizes,
recommended inflation pressure
and the maximum weight the
vehicle can carry.
*Tire Identification Number
(TIN): A number on the sidewall
of each tire providing information
about the tire brand and
manufacturing plant, tire size and
date of manufacture. Also referred
to as DOT code.
*Inflation pressure: A measure
of the amount of air in a tire.

Temperature A B C
WARNING
The temperature grade for
this tire is established for a
tire that is properly inflated and
not overloaded. Excessive speed,
underinflation, or excessive
loading, either separately or in
combination, can cause heat
buildup and possible tire failure.
The temperature grades are A
(the highest), B and C,
representing the tire’s resistance
to the generation of heat and its
ability to dissipate heat when
tested under controlled conditions
on a specified indoor laboratory
269

F150 (TF6) , enUSA

Wheels and Tires
B-pillar: The structural member
at the side of the vehicle behind
the front door.
*Bead area of the tire: Area of
the tire next to the rim.
* Sidewall of the tire: Area
between the bead area and the
tread.
*Tread area of the tire: Area of
the perimeter of the tire that
contacts the road when mounted
on the vehicle.
*Rim: The metal support (wheel)
for a tire or a tire and tube
assembly upon which the tire
beads are seated.

*Standard load: A class of
P-metric or Metric tires designed
to carry a maximum load at set
pressure. For example: For
P-Metric tires 35 psi (2.4 bar) or
36 psi (2.5 bar) depending on tire
size and for Metric 36 psi (2.5 bar).
Increasing the inflation pressure
beyond this pressure will not
increase the tire’s load carrying
capability.
*Extra load: A class of P-metric
or Metric tires designed to carry a
heavier maximum load at 42 psi
(2.9 bar). Increasing the inflation
pressure beyond this pressure will
not increase the tire’s load
carrying capability.
*kPa: Kilopascal, a metric unit of
air pressure.
*PSI: Pounds per square inch, a
standard unit of air pressure.
*Cold tire pressure: The tire
pressure when the vehicle has
been stationary and out of direct
sunlight for an hour or more and
prior to the vehicle being driven for
1 mile (1.6 kilometers).
*Recommended inflation
pressure: The cold inflation
pressure found on the Safety
Compliance Certification Label
(affixed to either the door hinge
pillar, door-latch post, or the door
edge that meets the door-latch
post, next to the driver's seating
position), or Tire Label located on
the B-pillar or the edge of the
driver's door.

Information Contained on the
Tire Sidewall
Both United States and Canada
Federal regulations require tire
manufacturers to place
standardized information on the
sidewall of all tires. This
information identifies and
describes the fundamental
characteristics of the tire and also
provides a U.S. DOT Tire
Identification Number for safety
standard certification and in case
of a recall.

270

F150 (TF6) , enUSA

Wheels and Tires
B. 215: Indicates the nominal
width of the tire in millimeters
from sidewall edge to sidewall
edge. In general, the larger the
number, the wider the tire.
C. 65: Indicates the aspect ratio
which gives the tire's ratio of
height to width.
D. R: Indicates a radial type tire.
E. 15: Indicates the wheel or rim
diameter in inches. If you change
your wheel size, you will have to
purchase new tires to match the
new wheel diameter.
F. 95: Indicates the tire's load
index. It is an index that relates to
how much weight a tire can carry.
You may find this information in
your owner’s manual. If not,
contact a local tire dealer.
Note: You may not find this
information on all tires because it
is not required by federal law.
G. H: Indicates the tire's speed
rating. The speed rating denotes
the speed at which a tire is
designed to be driven for extended
periods of time under a standard
condition of load and inflation
pressure. The tires on your vehicle
may operate at different
conditions for load and inflation
pressure. These speed ratings may
need to be adjusted for the
difference in conditions. The
ratings range from 81 mph (130
km/h) to 186 mph (299 km/h).
These ratings are listed in the
following chart.

Information on P Type Tires

C D
B

G
H

E142543

P215/65R15 95H is an example of
a tire size, load index and speed
rating. The definitions of these
items are listed below. (Note that
the tire size, load index and speed
rating for your vehicle may be
different from this example.)
A. P: Indicates a tire, designated
by the Tire and Rim Association,
that may be used for service on
cars, sport utility vehicles,
minivans and light trucks. Note: If
your tire size does not begin with
a letter this may mean it is
designated by either the European
Tire and Rim Technical
Organization or the Japan Tire
Manufacturing Association.

271

F150 (TF6) , enUSA

Wheels and Tires
the last four numbers represent
the week and year the tire was
built. For example, the numbers
317 mean the 31st week of 1997.
After 2000 the numbers go to four
digits. For example, 2501 means
the 25th week of 2001. The
numbers in between are
identification codes used for
traceability. This information is
used to contact customers if a tire
defect requires a recall.
I. M+S or M/S: Mud and Snow, or

Note: You may not find this
information on all tires because it
is not required by federal law.
Letter
rating

mph ( km/h)

81 mph (130 km/h)

87 mph (140 km/h)

99 mph (159 km/h)

106 mph (171 km/h)

112 mph (180 km/h)

118 mph (190 km/h)

124 mph (200 km/h)

130 mph (210 km/h)

149 mph (240 km/h)

168 mph (270 km/h)

AT: All Terrain, or
AS: All Season.
J. Tire Ply Composition and
Material Used: Indicates the
number of plies or the number of
layers of rubber-coated fabric in
the tire tread and sidewall. Tire
manufacturers also must indicate
the ply materials in the tire and the
sidewall, which include steel,
nylon, polyester, and others.
K. Maximum Load: Indicates the
maximum load in kilograms and
pounds that can be carried by the
tire. (affixed to either the door
hinge pillar, door-latch post, or the
door edge that meets the
door-latch post, next to the
driver's seating position), or Tire
Label located on the B-pillar or
the edge of the driver's door.
L. Treadwear, Traction and
Temperature Grades:

Y
186 mph (299 km/h)
Note: For tires with a maximum
speed capability over 149 mph
(240 km/h), tire manufacturers
sometimes use the letters ZR. For
those with a maximum speed
capability over 186 mph (299
km/h), tire manufacturers always
use the letters ZR.
H. U.S. DOT Tire Identification
Number: This begins with the
letters DOT and indicates that the
tire meets all federal standards.
The next two numbers or letters
are the plant code designating
where it was manufactured, the
next two are the tire size code and
272

F150 (TF6) , enUSA

Wheels and Tires
that meets the door-latch post,
next to the driver's seating
position), or Tire Label located on
the B-pillar or the edge of the
driver's door. The cold inflation
pressure should never be set lower
than the recommended pressure
on the vehicle label.
The tire suppliers may have
additional markings, notes or
warnings such as standard load
or radial tubeless.

*Treadwear The treadwear grade
is a comparative rating based on
the wear rate of the tire when
tested under controlled conditions
on a specified government test
course. For example, a tire graded
150 would wear 1½ times as well
on the government course as a tire
graded 100.
*Traction: The traction grades,
from highest to lowest are AA, A,
B, and C. The grades represent the
tire's ability to stop on wet
pavement as measured under
controlled conditions on specified
government test surfaces of
asphalt and concrete. A tire
marked C may have poor traction
performance.
*Temperature: The temperature
grades are A (the highest), B and
C, representing the tire's
resistance to the generation of
heat and its ability to dissipate
heat when tested under controlled
conditions on a specified indoor
laboratory test wheel.
M. Maximum Inflation
Pressure: Indicates the tire
manufacturers' maximum
permissible pressure or the
pressure at which the maximum
load can be carried by the tire. This
pressure is normally higher than
the vehicle manufacturer's
recommended cold inflation
pressure which can be found on
the Safety Compliance
Certification Label (affixed to
either the door hinge pillar,
door-latch post, or the door edge

Additional Information
Contained on the Tire Sidewall
for LT Type Tires
Note: Tire Quality Grades do not
apply to this type of tire.

B
A

D
E142544

LT type tires have some additional
information beyond those of P
type tires. These differences are
described below.

273

F150 (TF6) , enUSA

Wheels and Tires
A. LT: Indicates a tire, designated
by the Tire and Rim Association,
that is intended for service on light
trucks.
B. Load Range and Load
Inflation Limits: Indicates the
tire's load-carrying capabilities
and its inflation limits.
C. Maximum Load Dual lb (kg)
at psi (kPa) cold: Indicates the
maximum load and tire pressure
when the tire is used as a dual;
defined as four tires on the rear
axle (a total of six or more tires on
the vehicle).
D. Maximum Load Single lb
(kg) at psi (kPa) cold: Indicates
the maximum load and tire
pressure when the tire is used as
a single; defined as two tires
(total) on the rear axle.

B
A

D
E

E142545

T type tires have some additional
information beyond those of P
type tires. These differences are
described below:
A. T: Indicates a type of tire,
designated by the Tire and Rim
Association, that is intended for
temporary service on cars, sport
utility vehicles, minivans and light
trucks.
B. 145: Indicates the nominal
width of the tire in millimeters
from sidewall edge to sidewall
edge. In general, the larger the
number, the wider the tire.

Information on T Type Tires
T145/80D16 is an example of a
tire size.
Note: The temporary tire size for
your vehicle may be different from
this example. Tire Quality Grades
do not apply to this type of tire.

274

F150 (TF6) , enUSA

Wheels and Tires
C. 80: Indicates the aspect ratio
which gives the tire's ratio of
height to width. Numbers of 70 or
lower indicate a short sidewall.
D. D: Indicates a diagonal type tire.
R: Indicates a radial type tire.
E. 16: Indicates the wheel or rim
diameter in inches. If you change
your wheel size, you will have to
purchase new tires to match the
new wheel diameter.

You are strongly urged to buy a
reliable tire pressure gauge, as
automatic service station gauges
may be inaccurate. Ford
recommends the use of a digital
or dial-type tire pressure gauge
rather than a stick-type tire
pressure gauge.
Use the recommended cold
inflation pressure for optimum tire
performance and wear.
Under-inflation or over-inflation
may cause uneven treadwear
patterns

Location of the Tire Label
You will find a Tire Label
containing tire inflation pressure
by tire size and other important
information located on the B-Pillar
or the edge of the driver's door.
See Load Carrying (page 179).

WARNING
Under-inflation is the most
common cause of tire failures
and may result in severe tire
cracking, tread separation or
blowout, with unexpected loss of
vehicle control and increased risk
of injury. Under-inflation increases
sidewall flexing and rolling
resistance, resulting in heat
buildup and internal damage to
the tire. It also may result in
unnecessary tire stress, irregular
wear, loss of vehicle control and
accidents. A tire can lose up to
half of its air pressure and not
appear to be flat!

Inflating Your Tires
Safe operation of your vehicle
requires that your tires are
properly inflated. Remember that
a tire can lose up to half of its air
pressure without appearing flat.
Every day before you drive, check
your tires. If one looks lower than
the others, use a tire gauge to
check pressure of all tires and
adjust if required.
At least once a month and before
long trips, inspect each tire and
check the tire pressure with a tire
gauge (including spare, if
equipped). Inflate all tires to the
inflation pressure recommended
by Ford Motor Company.

Always inflate your tires to the
Ford recommended inflation
pressure even if it is less than the
maximum inflation pressure
information found on the tire. The
Ford recommended tire inflation
pressure is found on the Safety
Compliance Certification Label or
275

F150 (TF6) , enUSA

Wheels and Tires
the manufacturer’s recommended
cold inflation pressure which can
be found on the Safety
Compliance Certification Label
(affixed to either the door hinge
pillar, door-latch post, or the door
edge that meets the door-latch
post, next to the driver's seating
position), or Tire Label located on
the B-pillar or the edge of the
driver's door. The cold inflation
pressure should never be set lower
than the recommended pressure
on the Safety Compliance
Certification Label or Tire Label.
When weather temperature
changes occur, tire inflation
pressures also change. A 10°F
(6°C) temperature drop can
cause a corresponding drop of 1
psi (7 kPa) in inflation pressure.
Check your tire pressures
frequently and adjust them to the
proper pressure which can be
found on the Safety Compliance
Certification Label or Tire Label.
To check the pressure in your
tire(s):
1. Make sure the tires are cool,
meaning they are not hot from
driving even a mile.

Tire Label (affixed to either the
door hinge pillar, door-latch post,
or the door edge that meets the
door-latch post, next to the
driver's seating position), or Tire
Label located on the B-pillar or
the edge of the driver's door.
Failure to follow the tire pressure
recommendations can cause
uneven treadwear patterns and
adversely affect the way your
vehicle handles
Note: Do not reduce tire pressure
to change the ride characteristics
of the vehicle. If you do not
maintain the inflation pressure at
the levels specified by Ford, your
vehicle may experience a condition
known as shimmy. Shimmy is a
severe vibration and oscillation in
the steering wheel after the vehicle
travels over a bump or dip in the
road that does not dampen out by
itself. Shimmy may result from
significant under-inflation of the
tires, improper tires (load range,
size, or type), or vehicle
modifications such as lift-kits. In
the event that your vehicle
experiences shimmy, you should
slowly reduce speed by either lifting
off the accelerator pedal or lightly
applying the brakes. The shimmy
will cease as the vehicle speed
decreases.
Maximum Inflation Pressure is
the tire manufacturer's maximum
permissible pressure and the
pressure at which the maximum
load can be carried by the tire. This
pressure is normally higher than
276

F150 (TF6) , enUSA

Wheels and Tires
Note: If you are checking tire
pressure when the tire is hot, (for
example, driven more than 1 mile
[1.6 kilometers]), never bleed or
reduce air pressure. The tires are
hot from driving and it is normal for
pressures to increase above
recommended cold pressures. A
hot tire at or below recommended
cold inflation pressure could be
significantly under-inflated.
Note: If you have to drive a
distance to get air for your tire(s),
check and record the tire pressure
first and add the appropriate air
pressure when you get to the
pump. It is normal for tires to heat
up and the air pressure inside to go
up as you drive.
2. Remove the cap from the valve
on one tire, then firmly press the
tire gauge onto the valve and
measure the pressure.
3. Add enough air to reach the
recommended air pressure.
Note: If you overfill the tire, release
air by pressing on the metal stem
in the center of the valve. Then
recheck the pressure with your tire
gauge.
4. Replace the valve cap.
5. Repeat this procedure for each
tire, including the spare.

Note: Some spare tires operate at
a higher inflation pressure than the
other tires. For T type mini-spare
tires, (see the Dissimilar spare
wheel and tire assembly
information for a description. Store
and maintain at 60 psi (4.15 bar).
For full-size and dissimilar spare
tires, see the Dissimilar spare wheel
and tire assembly information for
a description. Store and maintain
at the higher of the front and rear
inflation pressure as shown on the
Safety Compliance Certification
Label or Tire Label.
6. Visually inspect the tires to
make sure there are no nails or
other objects embedded that
could poke a hole in the tire and
cause an air leak.
7. Check the sidewalls to make
sure there are no gouges, cuts or
bulges.
Inspecting Your Tires and
Wheel Valve Stems
Periodically inspect the tire treads
for uneven or excessive wear and
remove objects such as stones,
nails or glass that may be wedged
in the tread grooves. Check the tire
and valve stems for holes, cracks,
or cuts that may permit air
leakage and repair or replace the
tire and replace the valve stem.
Inspect the tire sidewalls for
cracking, cuts, bruises and other
signs of damage or excessive
wear. If internal damage to the tire
is suspected, have the tire
demounted and inspected in case
277

F150 (TF6) , enUSA

Wheels and Tires
When the tire tread wears down
to the same height as these wear
bars, the tire is worn out and must
be replaced.

it needs to be repaired or replaced.
For your safety, tires that are
damaged or show signs of
excessive wear should not be used
because they are more likely to
blow out or fail.
Improper or inadequate vehicle
maintenance can cause tires to
wear abnormally. Inspect all your
tires, including the spare,
frequently, and replace them if
one or more of the following
conditions exist:

Damage
Periodically inspect the tire treads
and sidewalls for damage (such
as bulges in the tread or sidewalls,
cracks in the tread groove and
separation in the tread or
sidewall). If damage is observed
or suspected have the tire
inspected by a tire professional.
Tires can be damaged during
off-road use, so inspection after
off-road use is also
recommended.

Tire Wear

E142546

When the tread is worn down to
one sixteenth of an inch (2
millimeters), tires must be
replaced to help prevent your
vehicle from skidding and
hydroplaning. Built-in treadwear
indicators, or wear bars, which
look like narrow strips of smooth
rubber across the tread will
appear on the tire when the tread
is worn down to one sixteenth of
an inch (2 millimeters).

278

F150 (TF6) , enUSA

Wheels and Tires
This begins with the letters DOT
and indicates that the tire meets
all federal standards. The next
two numbers or letters are the
plant code designating where it
was manufactured, the next two
are the tire size code and the last
four numbers represent the week
and year the tire was built. For
example, the numbers 317 mean
the 31st week of 1997. After 2000
the numbers go to four digits. For
example, 2501 means the 25th
week of 2001. The numbers in
between are identification codes
used for traceability. This
information is used to contact
customers if a tire defect requires
a recall.

Age
WARNING
Tires degrade over time
depending on many factors
such as weather, storage
conditions, and conditions of use
(load, speed, inflation pressure)
the tires experience throughout
their lives.
In general, tires should be
replaced after six years regardless
of tread wear. However, heat
caused by hot climates or
frequent high loading conditions
can accelerate the aging process
and may require tires to be
replaced more frequently.

Tire Replacement
Requirements

You should replace your spare tire
when you replace the road tires or
after six years due to aging even if
it has not been used.

Your vehicle is equipped with tires
designed to provide a safe ride
and handling capability.

U.S. DOT Tire Identification
Number

WARNINGS
Only use replacement tires
and wheels that are the same
size, load index, speed rating and
type (such as P-metric versus
LT-metric or all-season versus
all-terrain) as those originally
provided by Ford. The
recommended tire and wheel size
may be found on either the Safety
Compliance Certification Label or
the Tire Label. If this information
is not found on these labels then
you should contact your
authorized dealer as soon as
possible. Use of any tire or wheel

Both United States and Canada
Federal regulations require tire
manufacturers to place
standardized information on the
sidewall of all tires. This
information identifies and
describes the fundamental
characteristics of the tire and also
provides a U.S. DOT Tire
Identification Number for safety
standard certification and in case
of a recall.

279

F150 (TF6) , enUSA

Wheels and Tires
WARNINGS
not recommended by Ford can
affect the safety and performance
of your vehicle, which could result
in an increased risk of loss of
vehicle control, vehicle rollover,
personal injury and death.
Additionally the use of
non-recommended tires and
wheels could cause steering,
suspension, axle, transfer case or
power transfer unit failure. If you
have questions regarding tire
replacement, contact your
authorized dealer as soon as
possible.
To reduce the risk of serious
injury, when mounting
replacement tires and wheels, you
should not exceed the maximum
pressure indicated on the sidewall
of the tire to set the beads without
additional precautions listed
below. If the beads do not seat at
the maximum pressure indicated,
re-lubricate and try again

WARNINGS
3. Stand at a minimum of 12 feet
(3.6 meters) away from the wheel
and tire assembly.
4. Use both eye and ear
protection.
For a mounting pressure more
than 20 psi (1.38 bar) greater than
the maximum pressure, a Ford
dealer or other tire service
professional should do the
mounting.
Always inflate steel carcass tires
with a remote air fill with the
person inflating standing at a
minimum of 12 feet (3.6 meters)
away from the wheel and tire
assembly
Important: Remember to replace
the wheel valve stems when the
road tires are replaced on your
vehicle
The two front tires or two rear tires
should generally be replaced as a
pair.
The tire pressure sensors mounted
in the wheels are not designed to
be used in aftermarket wheels.
The use of wheels or tires not
recommended by Ford Motor
Company may affect the
operation of your tire pressure
monitoring system.

When inflating the tire for
mounting pressures up to 20 psi
(1.38 bar) greater than the
maximum pressure on the tire
sidewall, the following
precautions must be taken to
protect the person mounting the
tire:
1. Make sure that you have the
correct tire and wheel size.
2. Lubricate the tire bead and
wheel bead seat area again.
280

F150 (TF6) , enUSA

Wheels and Tires
Highway Hazards

If the tire pressure monitoring
system indicator is flashing, the
system is malfunctioning. Your
replacement tire might be
incompatible with your tire
pressure monitoring system, or
some component of the system
may be damaged.

No matter how carefully you drive
there’s always the possibility that
you may eventually have a flat tire
on the highway. Drive slowly to the
closest safe area out of traffic.
This may further damage the flat
tire, but your safety is more
important.
If you feel a sudden vibration or
ride disturbance while driving, or
you suspect your tire or vehicle
has been damaged, immediately
reduce your speed. Drive with
caution until you can safely pull
off the road. Stop and inspect the
tires for damage. If a tire is
under-inflated or damaged,
deflate it, remove wheel and
replace it with your spare tire and
wheel. If you cannot detect a
cause, have the vehicle towed to
the nearest repair facility or tire
dealer to have the vehicle
inspected.

Safety Practices
WARNINGS
If your vehicle is stuck in
snow, mud, or sand, do not
rapidly spin the tires; spinning the
tires can tear the tire and cause
an explosion. A tire can explode in
as little as three to five seconds.
Do not spin the wheels at
over 35 mph (56 km/h). The
tires may fail and injure a
passenger or bystander.
Driving habits have a great deal
to do with your tire mileage and
safety.

Tire and Wheel Alignment

*Observe posted speed limits
*Avoid fast starts, stops and turns
*Avoid potholes and objects on
the road
*Do not run over curbs or hit the
tire against a curb when parking

A bad jolt from hitting a curb or
pothole can cause the front end
of your vehicle to become
misaligned or cause damage to
your tires. If your vehicle seems to
pull to one side when you’re
driving, the wheels may be out of
alignment. Have an authorized
dealer check the wheel alignment
periodically.

281

F150 (TF6) , enUSA

Wheels and Tires
Note: Your vehicle may be
equipped with a dissimilar spare
wheel and tire assembly. A
dissimilar spare wheel and tire
assembly is defined as a spare
wheel and tire assembly that is
different in brand, size or
appearance from the road tires and
wheels. If you have a dissimilar
spare wheel and tire assembly it is
intended for temporary use only
and should not be used in a tire
rotation.
Note: After having your tires
rotated, inflation pressure must be
checked and adjusted to the
vehicle requirements.
Rotating your tires at the
recommended interval (as
indicated in the Scheduled
Maintenance chapter) will help
your tires wear more evenly,
providing better tire performance
and longer tire life.
Rear-wheel drive vehicles and
four-wheel drive vehicles (front
tires at left of diagram)

Wheel misalignment in the front
or the rear can cause uneven and
rapid treadwear of your tires and
should be corrected by an
authorized dealer. Front-wheel
drive vehicles and those with an
independent rear suspension may
require alignment of all four
wheels.
The tires should also be balanced
periodically. An unbalanced tire
and wheel assembly may result in
irregular tire wear.
Tire Rotation
WARNING
If the tire label shows
different tire pressures for the
front and rear tires and the vehicle
is equipped with a tire pressure
monitoring system, then the
settings for the system sensors
need to be updated. Always
perform the system reset
procedure after tire rotation. If the
system is not reset, it may not
provide a low tire pressure
warning when necessary. See the
tire pressure monitoring system
reset procedure in this chapter.
Note: If your tires show uneven
wear ask an authorized dealer to
check for and correct any wheel
misalignment, tire imbalance or
mechanical problem involved
before tire rotation.

E142548

Sometimes irregular tire wear can
be corrected by rotating the tires.
282

F150 (TF6) , enUSA

Wheels and Tires
•

USING SNOW CHAINS
WARNING
Snow tires must be the same size,
load index, speed rating as those
originally provided by Ford. Use of
any tire or wheel not recommended by
Ford can affect the safety and
performance of your vehicle, which could
result in an increased risk of loss of vehicle
control, vehicle rollover, personal injury and
death. Additionally, the use of
non-recommended tires and wheels could
cause steering, suspension, axle, transfer
case or power transfer unit failure.

•

If you have any questions regarding snow
chains or cables, please contact your
authorized dealer.

TIRE PRESSURE MONITORING
SYSTEM
WARNING

Note: The suspension insulation and
bumpers will help prevent vehicle damage.
Do not remove these components from your
vehicle when using snow tires and chains.

The tire pressure monitoring system
is not a substitute for manually
checking tire pressure. The tire
pressure should be checked periodically
(at least monthly) using a tire gauge, see
Inflating your tires in this chapter. Failure
to properly maintain your tire pressure
could increase the risk of tire failure, loss
of control, vehicle rollover and personal
injury.

Note: Do not place chains on the following
tires sizes: P265/60R18, P275/65R18,
LT275/65R18, LT315/70R17, P275/55R20,
and P275/45R22.
The tires on your vehicle have all-weather
treads to provide traction in rain and snow.
However, in some climates, you may need
to use snow tires and cables. If you need
to use cables, it is recommended that steel
wheels (of the same size and
specifications) be used, as cables may chip
aluminum wheels.

Each tire, including the spare (if
provided), should be checked
monthly when cold and inflated
to the inflation pressure
recommended by the vehicle manufacturer
on the vehicle placard or tire inflation
pressure label. (If your vehicle has tires of
a different size than the size indicated on
the vehicle placard or tire inflation pressure
label, you should determine the proper tire
inflation pressure for those tires.)

Follow these guidelines when using snow
tires and chains:
•
•
•

If possible, avoid fully loading your
vehicle
Use only SAE Class S chains.
Install chains securely, verifying that
the chains do not touch any wiring,
brake lines or fuel lines.

As an added safety feature, your vehicle
has been equipped with a Tire Pressure
Monitoring System (TPMS) that
illuminates a low tire pressure telltale
when one or more of your tires is
significantly under-inflated. Accordingly,

283

F150 (TF6) , enUSA

Drive cautiously. If you hear the chains
rub or bang against your vehicle, stop
and retighten the chains. If this does
not work, remove the chains to prevent
damage to your vehicle.
Remove the tire chains when they are
no longer needed. Do not use tire
chains on dry roads.

Wheels and Tires
when the low tire pressure telltale
illuminates, you should stop and check
your tires as soon as possible, and inflate
them to the proper pressure. Driving on a
significantly under-inflated tire causes the
tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency
and tire tread life, and may affect the
vehicle’s handling and stopping ability.

The tire pressure monitoring system
complies with part 15 of the FCC rules and
with RSS-210 of Industry Canada.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) This device
must accept any interference received,
including interference that may cause
undesired operation.

Please note that the TPMS is not a
substitute for proper tire maintenance, and
it is the driver’s responsibility to maintain
correct tire pressure, even if under-inflation
has not reached the level to trigger
illumination of the TPMS low tire pressure
telltale.

Changing Tires With a Tire
Pressure Monitoring System

Your vehicle has also been equipped with
a TPMS malfunction indicator to indicate
when the system is not operating properly.
The TPMS malfunction indicator is
combined with the low tire pressure
telltale. When the system detects a
malfunction, the telltale will flash for
approximately one minute and then remain
continuously illuminated. This sequence
will continue upon subsequent vehicle
start-ups as long as the malfunction exists.

E142549

Note: Each road tire is equipped with a tire
pressure sensor located inside the wheel
and tire assembly cavity. The pressure
sensor is attached to the valve stem. The
pressure sensor is covered by the tire and is
not visible unless the tire is removed. Take
care when changing the tire to avoid
damaging the sensor

When the malfunction indicator is
illuminated, the system may not be able
to detect or signal low tire pressure as
intended. TPMS malfunctions may occur
for a variety of reasons, including the
installation of replacement or alternate
tires or wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more tires or
wheels on your vehicle to ensure that the
replacement or alternate tires and wheels
allow the TPMS to continue to function
properly.

You should always have your tires serviced
by an authorized dealer.
Check the tire pressure periodically (at
least monthly) using an accurate tire
gauge. See Inflating Your Tires in this
chapter.

284

F150 (TF6) , enUSA

Wheels and Tires
Understanding Your Tire Pressure
Monitoring System

When Your Temporary Spare Tire is
Installed

The tire pressure monitoring system
measures pressure in your four road tires
and sends the tire pressure readings to
your vehicle. The low tire pressure warning
light will turn on if the tire pressure is
significantly low. Once the light is
illuminated, your tires are under-inflated
and need to be inflated to the
manufacturer’s recommended tire
pressure. Even if the light turns on and a
short time later turns off, your tire pressure
still needs to be checked.

When one of your road tires needs to be
replaced with the temporary spare, the
system will continue to identify an issue to
remind you that the damaged road wheel
and tire assembly needs to be repaired and
put back on your vehicle.
To restore the full function of the tire
pressure monitoring system, have the
damaged road wheel and tire assembly
repaired and remounted on your vehicle.
When You Believe Your System is Not
Operating Properly
The main function of the tire pressure
monitoring system is to warn you when
your tires need air. It can also warn you in
the event the system is no longer capable
of functioning as intended. See the
following chart for information concerning
your tire pressure monitoring system:

285

F150 (TF6) , enUSA

Wheels and Tires

Low tire pressure
warning light

Possible cause

Customer action required

Solid warning light

Tire(s) under-inflated

Make sure tires are at the proper pressure. See Inflating your tires in this
chapter. After inflating your tires to the
manufacturer’s recommended pressure
as shown on the Tire Label (located on
the edge of driver’s door or the B-Pillar),
the vehicle must be driven for at least
two minutes over 20 mph (32 km/h)
before the light turns off.

Spare tire in use

Repair the damaged road wheel and tire
assembly and reinstall it on the vehicle
to restore system function. For a
description on how the system functions,
see When your temporary spare tire
is installed in this section.

Tire pressure monitoring If the tires are properly inflated and the
system malfunction
spare tire is not in use but the light
remains on, contact your authorized
dealer as soon as possible.

Flashing warning
light

Tire rotation without
sensor training

On vehicles with different front and rear
tire pressures, the system must be
retrained following every tire rotation.
See Tire Care (page 268).

Spare tire in use

Tire pressure monitoring If the tires are properly inflated and the
system malfunction
spare tire is not in use but the light
remains on, contact your authorized
dealer as soon as possible.

286

F150 (TF6) , enUSA

Wheels and Tires
When Inflating Your Tires

Tire Pressure Monitoring System Reset
Procedure

When putting air into your tires (such as at
a gas station or in your garage), the tire
pressure monitoring system may not
respond immediately to the air added to
your tires.

WARNING
To determine the required
pressure(s) for your vehicle, see the
Safety Compliance Certification
Label (affixed to either the door hinge
pillar, door-latch post, or the door edge
that meets the door-latch post, next to the
driver's seating position), or Tire Label
located on the B-Pillar or the edge of the
driver's door.

It may take up to two minutes of driving
over 20 mph (32 km/h) for the light to turn
off after you have filled your tires to the
recommended inflation pressure
How Temperature Affects Your Tire
Pressure
The tire pressure monitoring system
monitors tire pressure in each pneumatic
tire. While driving in a normal manner, a
typical passenger tire inflation pressure
may increase about 2 to 4 psi (14 to 28
kPa) from a cold start situation. If the
vehicle is stationary overnight with the
outside temperature significantly lower
than the daytime temperature, the tire
pressure may decrease about 3 psi (21
kPa) for a drop of 30°F (17°C) in ambient
temperature. This lower pressure value
may be detected by the tire pressure
monitoring system as being significantly
lower than the recommended inflation
pressure and activate the system warning
light for low tire pressure.

Note: You need to perform the tire pressure
monitoring system reset procedure after
each tire rotation on vehicles that require
different recommended tire pressures in the
front tires as compared to the rear tires.
Overview
To provide the vehicle's load carrying
capability, some vehicles require different
recommended tire pressures in the front
tires as compared to the rear tires. The tire
pressure monitoring system equipped on
these vehicles is designed to illuminate the
low tire pressure warning light at two
different pressures; one for the front tires
and one for the rear tires.
Since tires need to be rotated to provide
consistent performance and maximum tire
life, the tire pressure monitoring system
needs to know when the tires are rotated
to determine which set of tires are on the
front and which are on the rear. With this
information, the system can detect and
properly warn of low tire pressures.

If the low tire pressure warning light is on,
visually check each tire to verify that no tire
is flat. If one or more tires are flat, repair as
necessary. Check the air pressure in the
road tires. If any tire is under-inflated,
carefully drive the vehicle to the nearest
location where air can be added to the
tires. Inflate all the tires to the
recommended inflation pressure.

System reset tips:

287

F150 (TF6) , enUSA

Wheels and Tires
•

•

To reduce the chances of interference
from another vehicle, perform the
system reset procedure at least three
feet (one meter) away from another
Ford Motor Company vehicle
undergoing the system reset procedure
at the same time.
Do not wait more than two minutes
between resetting each tire sensor or
the system will time-out and the entire
procedure will have to be repeated on
all four wheels.
A double horn will sound indicating the
need to repeat the procedure.

5. Train the tire pressure monitoring
system sensors in the tires using the
following system reset sequence
starting with the left front tire in the
following clockwise order: Left front
(driver's side front tire), Right front
(passenger's side front tire), Right rear
(passenger's side rear tire), Left rear
(driver's side rear tire)
6. Remove the valve cap from the valve
stem on the left front tire. Decrease the
air pressure until the horn sounds.
Note: The single horn chirp confirms
that the sensor identification code has
been learned by the module for this
position. If a double horn is heard, the
reset procedure was unsuccessful, and
you must repeat it.
7. Remove the valve cap from the valve
stem on the right front tire. Decrease
the air pressure until the horn sounds.
8. Remove the valve cap from the valve
stem on the right rear tire. Decrease the
air pressure until the horn sounds.
9. Remove the valve cap from the valve
stem on the left rear tire. Decrease the
air pressure until the horn sounds.
Training is complete after the horn
sounds for the last tire trained (driver's
side rear tire), the system indicator
stops flashing, and a message is shown
in the information display.
10. Turn the ignition off. If two short horn
beeps are heard, the reset procedure
was unsuccessful and you must
repeat it. If after repeating the
procedure and two short beeps are
heard when the ignition is turned to
off, seek assistance from your
authorized dealer.

Performing the System Reset Procedure
Read the entire procedure before
attempting.
1.

Drive the vehicle above 20 mph (32
km/h) for at least two minutes, then
park in a safe location where you can
easily get to all four tires and have
access to an air pump.
2. Place the ignition in the off position and
keep the key in the ignition.
3. Cycle the ignition to the on position
with the engine off.
4. Turn the hazard flashers on then off
three times. You must accomplish this
within 10 seconds. If the reset mode
has been entered successfully, the horn
will sound once, the system indicator
will flash and a message is shown in
the information display. If this does not
occur, please try again starting at Step
2. If after repeated attempts to enter
the reset mode, the horn does not
sound, the system indicator does not
flash and no message is shown in the
information display, seek service from
your authorized dealer.

288

F150 (TF6) , enUSA

Wheels and Tires
11.

Dissimilar Spare Wheel and Tire
Assembly Information

Set all four tires to the recommended
air pressure as indicated on the
Safety Compliance Certification
Label (affixed to either the door hinge
pillar, door-latch post, or the door
edge that meets the door-latch post,
next to the driver's seating position)
or Tire Label located on the B-Pillar
or the edge of the driver's door.

WARNING
Failure to follow these guidelines
could result in an increased risk of
loss of vehicle control, injury or death.
If you have a dissimilar spare wheel and
tire, then it is intended for temporary use
only. This means that if you need to use it,
you should replace it as soon as possible
with a road wheel and tire assembly that
is the same size and type as the road tires
and wheels that were originally provided
by Ford. If the dissimilar spare tire or wheel
is damaged, it should be replaced rather
than repaired.

CHANGING A ROAD WHEEL
WARNINGS
The use of tire sealants may damage
your tire pressure monitoring system
and should not be used. However, if
you must use a sealant, the tire pressure
monitoring system sensor and valve stem
on the wheel must be replaced by an
authorized dealer.

A dissimilar spare wheel and tire assembly
is defined as a spare wheel and tire
assembly that is different in brand, size or
appearance from the road tires and wheels
and can be one of three types:

If the tire pressure monitor sensor
becomes damaged, it will no longer
function. See Tire Pressure
Monitoring System (page 283).

1. T-type mini-spare: This spare tire
begins with the letter T for tire size and
may have Temporary Use Only molded in
the sidewall.

Note: The tire pressure monitoring system
indicator light will illuminate when the spare
tire is in use. To restore the full function of
the monitoring system, all road wheels
equipped with tire pressure monitoring
sensors must be mounted on this vehicle.

2. Full-size dissimilar spare with label
on wheel: This spare tire has a label on
the wheel that states: THIS WHEEL AND
TIRE ASSEMBLY FOR TEMPORARY USE
ONLY

If you get a flat tire while driving, do not
apply the brake heavily. Instead, gradually
decrease your speed. Hold the steering
wheel firmly and slowly move to a safe
place on the side of the road.

When driving with one of the dissimilar
spare tires listed above, do not:
•
•

Have a flat serviced by an authorized
dealer in order to prevent damage to the
system sensors See Tire Pressure
Monitoring System (page 283). Replace
the spare tire with a road tire as soon as
possible. During repairing or replacing of
the flat tire, have the authorized dealer
inspect the system sensor for damage.

•
•
•

289

F150 (TF6) , enUSA

Exceed 50 mph (80 km/h)
Load the vehicle beyond maximum
vehicle load rating listed on the Safety
Compliance Label.
Tow a trailer.
Use snow chains on the end of the
vehicle with the dissimilar spare tire.
Use more than one dissimilar spare tire
at a time.

Wheels and Tires
•
•

Use commercial car washing
equipment.
Try to repair the dissimilar spare tire.

The usage of a full-size dissimilar spare
wheel and tire assembly can lead to
impairment of the following:
• Handling, stability and braking
performance.
• Comfort and noise.
• Ground clearance and parking at curbs.
• Winter weather driving capability.
• Wet weather driving capability.
• All-wheel driving capability

Use of one of the dissimilar spare tires
listed above at any one wheel location can
lead to impairment of the following:
• Handling, stability and braking
performance.
• Comfort and noise.
• Ground clearance and parking at curbs.
• Winter weather driving capability.
• Wet weather driving capability.
• All-wheel driving capability

When driving with the full-size dissimilar
spare wheel and tire assembly additional
caution should be given to:
• Towing a trailer.
• Driving vehicles equipped with a
camper body.
• Driving vehicles with a load on the
cargo rack.

3. Full-size dissimilar spare without
label on wheel
When driving with the full-size dissimilar
spare wheel and tire assembly, do not:
• Exceed 70 mph (113 km/h).
• Use more than one dissimilar spare
wheel and tire assembly at a time.
• Use commercial car washing
equipment.
• Use snow chains on the end of the
vehicle with the dissimilar spare wheel
and tire assembly.

Drive cautiously when using a full-size
dissimilar spare wheel and tire assembly
and seek service as soon as possible.

Location of the Spare Tire and
Tools
The spare tire is located under the vehicle,
just forward of the rear bumper. The jack,
jack handle and lug wrench are located in
the following locations:

Body style

Location

Regular Cab

Attached to a floor bracket behind or under
the driver's seat (for easier access, move
the driver seat forward)

SuperCab

Attached to a floor bracket under the rear
seat on the driver's side

SuperCrew

In a plastic box in the floor under the rear
seat

290

F150 (TF6) , enUSA

Wheels and Tires
Tire Change Procedure

Park on a level surface, activate the hazard
flashers and set the parking brake. Then,
place the transmission selector lever in
position P and turn the engine off.

WARNINGS
When one of the front wheels is off
the ground, the transmission alone
will not prevent the vehicle from
moving or slipping off the jack, even if the
transmission selector lever is in position P.

To remove the jack on Regular Cab and
SuperCab models:

To help prevent the vehicle from
moving when you change a tire, be
sure to place the transmission
selector lever in position P, set the parking
brake and block (in both directions) the
wheel that is diagonally opposite (other
side and end of the vehicle) to the tire
being changed.

To remove the jack on SuperCrew
models:

Remove the wing nut and turn the jack
screw counterclockwise to release
pressure before removing the jack from the
bracket.

1. Lift both rear seat cushions.
2. Remove the insert containing the Easy
Fuel funnel from the driver's side.
3. Remove the two small wing nuts on
the passenger side.
4. Slide the plastic box toward the driver's
side and remove.

Never get underneath a vehicle that
is supported only by a jack. If the
vehicle slips off the jack, you or
someone else could be seriously injured.
Do not attempt to change a tire on
the side of the vehicle close to
moving traffic. Pull far enough off the
road to avoid the danger of being hit when
operating the jack or changing the wheel.

See the instruction sheet (located with the
jack) for detailed tire change instructions.
Removing the spare tire

Always use the jack provided as
original equipment with your vehicle.
If using a jack other than the one
provided as original equipment with your
vehicle, make sure the jack capacity is
adequate for the vehicle weight, including
any vehicle cargo or modifications.
Disable the power running boards
before jacking, lifting, or placing any
object under the vehicle. Never place
your hand between the power running
board and the vehicle as extended power
running boards will retract when the doors
are closed. Failure to follow these
instructions may result in personal injury.

E166715

Note: Passengers should not remain in the
vehicle when the vehicle is being jacked.

291

F150 (TF6) , enUSA

Use the ignition key to remove the lock
cylinder from the access hole of the
bumper to allow access to the guide
tube. Assemble the jack handle as
shown in the illustration.

Wheels and Tires

E166716

E142551

2. Fully insert the jack handle through the
bumper hole and into the guide tube
through the access hole in the rear
bumper.
3. Turn the handle counterclockwise until
the tire is lowered to the ground, the
tire can be slid rearward and the cable
is slightly slack.
4. Slide the retainer through the center of
the wheel.

5. Block the diagonally opposite wheel.
Obtain the spare tire and jack from
their storage locations. Note: The
F-150 SVT Raptor also includes a
chock, saddle extension and wing
bolt.Use the tip of the lug wrench to
remove any wheel trim that is blocking
the lug nuts.
6. Loosen each wheel lug nut one-half
turn counterclockwise, but do not
remove them until the wheel is raised
off the ground.
Note: For the F-150 SVT Raptor, install the
saddle extension on the jack as shown in
the jack usage and storage instructions.

Jacking the vehicle
Front

E166717

Note: Use the frame rail as the jacking
location point, not the control arm.

Note: For the F-150 SVT Raptor, you must
always use the jack saddle extension.

292

F150 (TF6) , enUSA

Wheels and Tires
Rear

6. Stow the flat tire.
7. Stow the jack and lug wrench. Make
sure the jack is fastened so it does not
rattle when you drive.
8. Unblock the wheels.

1
3

6
5

E166719

Six lug nut wheel

1
3
6
E166718

Note: Jack at the specified locations to
avoid damage to the vehicle.
1.

2.
3.

4.
5.

Position the jack according to the
guides and turn the jack handle
clockwise until the wheel is completely
off the ground.
Remove the lug nuts with the lug
wrench.
Replace the flat tire with the spare tire,
making sure the valve stem is facing
outward. Reinstall the lug nuts until the
wheel is snug against the hub. Do not
fully tighten the lug nuts until the wheel
has been lowered.
Lower the wheel by turning the jack
handle counterclockwise.
Remove the jack and fully tighten the
lug nuts in the order shown. See
Technical Specifications (page 294).

7
E166720

Stowing the flat or spare tire
Note: Failure to follow the spare tire
stowage instructions may result in failure of
the cable or loss of the spare tire.
1.

293

F150 (TF6) , enUSA

Seven lug nut wheel

Lay the tire on the ground with the
valve stem facing in the direction
specified on the Tire Changing
Instructions located with the jack
hardware.

Wheels and Tires
2. Slide the wheel partially under the
vehicle and install the retainer through
the wheel center. Pull on the cable to
align the components at the end of the
cable.
3. Turn the jack handle clockwise until
the tire is raised to its stowed position
underneath the vehicle. The effort to
turn the jack handle increases
significantly and the spare tire carrier
ratchets or slips when the tire is raised
to the maximum tightness. Tighten to
the best of your ability, to the point
where the ratchet or slip occurs, if
possible. The spare tire carrier will not
allow you to overtighten. If the spare
tire carrier ratchets or slips with little
effort, take the vehicle to your
authorized dealer for assistance at your
earliest convenience.

4. Check that the tire lies flat against the
frame and is properly tightened. Try to
push or pull, then turn the tire to be
sure it will not move. Loosen and
retighten, if necessary. Failure to
properly stow the spare tire may result
in failure of the winch cable and loss
of the tire.
5. Repeat this tightness check procedure
when servicing the spare tire pressure
(every six months, as per your
scheduled maintenance information),
or at any time that the spare tire is
disturbed through service of other
components.
6. If removed, install the spare tire lock
into the bumper drive tube with the
spare tire lock key and jack handle.

TECHNICAL SPECIFICATIONS
Wheel Lug Nut Torque Specifications
WARNING
When a wheel is installed, always remove any corrosion, dirt or foreign materials
present on the mounting surfaces of the wheel or the surface of the wheel hub,
brake drum or brake disc that contacts the wheel. Make sure that any fasteners
that attach the rotor to the hub are secured so they do not interfere with the mounting
surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the
wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off
while your vehicle is in motion, resulting in loss of control.
Bolt size

lb.ft (Nm)

M14 x 2.0

148 lb.ft (200 Nm)

Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford
recommended replacement fasteners.

294

F150 (TF6) , enUSA

Wheels and Tires

E145950

Wheel pilot bore

Inspect the wheel pilot hole and
mounting surface prior to installation.
Remove any visible corrosion or loose
particles.

295

F150 (TF6) , enUSA

Capacities and Specifications
ENGINE SPECIFICATIONS
Engine

3.5L V6
Ecoboost

3.7 V6

5.0L V8

6.2L V8

Cubic inches

214

226

302

378

Required fuel

Minimum 87
octane

Minimum 87
octane or E85

Minimum 87
octane

Firing order

1-4-2-5-3-6

1-5-4-8-6-3-7-2

1-3-7-2-6-5-4-8

Ignition
system

Coil on plug

Spark plug
gap

.030-.033 in.
(.75-.85 mm)

.049-.053 in.
(1.25-1.35 mm)

.041-.047 in.
(1.04-1.20 mm)

Compression
ratio

10.0:1

10.5:1

9.8:1

Drivebelt Routing
3.5L V6 Ecoboost Engines with A/C

E167467

296

F150 (TF6) , enUSA

Capacities and Specifications
3.7L V6 Engines with A/C

E167464

5.0L V8 Engines with A/C

E167465

6.2L V8 Engines with A/C

E167466

297

F150 (TF6) , enUSA

Capacities and Specifications
MOTORCRAFT PARTS
Component

3.5L V6 Ecoboost

3.7L V6 engine

Air filter
element

5.0L V8 engine

6.2L V8 engine

FA-1883

Oil filter

FL-500-S

Battery

FL-500-S

FL-820-S

BXT-65-750
1

Spark plugs

SP-534/CYFS12-YT3

SP-520/CYFS12F-5

SP-519/CYFS12Y

Windshield
wiper blade

WW-2201-PF

Seat air filter

FS-104

Automatic
transmission
fluid filter

SP-526/CYFS12-FP

For spark plug replacement, see your
authorized dealer. See Scheduled
Maintenance (page 438). for the
appropriate intervals for changing the
spark plugs.
Note: Replace the spark plugs with ones
that meet Ford material and design
specifications for your vehicle, such as
Motorcraft or equivalent replacement parts.
The customer warranty may be void for any
damage to the engine if such spark plugs
are not used.
2

For Automatic transmission fluid filter
replacement, see your authorized dealer.

E142476

Please note that in the graphic, XXXX is
representative of your vehicle identification
number.

VEHICLE IDENTIFICATION
NUMBER

The Vehicle Identification Number contains
the following information:

The vehicle identification number is
located on the left-hand side of the
instrument panel.

298

F150 (TF6) , enUSA

Capacities and Specifications
VEHICLE CERTIFICATION
LABEL

E142477

World manufacturer identifier

Brake system, Gross Vehicle
Weight Rating, Restraint Devices
and their locations

Make, vehicle line, series, body
type

Engine type

Check digit

Model year

Assembly plant

Production sequence number

E167469

The National Highway Traffic Safety
Administration Regulations require that a
Safety Compliance Certification Label be
affixed to a vehicle and prescribe where
the Safety Compliance Certification Label
may be located. The Safety Compliance
Certification Label shall be affixed to either
the door hinge pillar, the door latch post,
or the edge of the door near the door latch,
next to the driver's seating position.

299

F150 (TF6) , enUSA

Capacities and Specifications
The transmission code is on the Safety
Compliance Certification Label. The
following table shows the transmission
code along with the transmission
description.

TRANSMISSION CODE
DESIGNATION

E167814

Description

Code

Six-speed automatic transmission 6R80E

300

F150 (TF6) , enUSA

Capacities and Specifications
TECHNICAL SPECIFICATIONS
Item

Capacity

Ford part name or
equivalent

Ford part number / Ford
specification

XL-1 (US); CXC-51-A
(Canada) / --

XL-5

Lock cylinders

—

Motorcraft Penetrating and Lock
Lubricant (US);
Motorcraft Penetrating Fluid
(Canada)

Hinges, latches,
striker plates, fuel
filler door hinge
and seat tracks

—

Motorcraft MultiPurpose Grease
Spray

Motorcraft DOT 4
Between MIN/MAX
LV High PerformPM-20 / WSS-M6C65-A2
on brake fluid reserance Motor Vehicle
voir
Brake Fluid

Brake fluid

3.5L EcoBoost

6.0 qt (5.7L)

2,3

engine oil

3.7L engine oil

2,3

6.2L engine oil

7.7 qt (7.3L)

2,3

7.0 qt (6.6L)

3.5L EcoBoost
engine coolant
3.7L engine
4

coolant

5.0L engine
4

coolant

6.2L engine
4

coolant

XO-5W30-QSP or XO5W30-QFS (US); CXO5W30-LSP12 or CXO5W30-LFS12 (Canada) /
WSS-M2C946-A

Motorcraft SAE
5W-20 Motor Oil

XO-5W20-QSP or XO5W20-QFS (US); CXO5W20-LSP12 or CXO5W20-LFS12 (Canada) /
WSS-M2C945-A

6.0 qt (5.7L)

2,3

5.0L engine oil

Motorcraft SAE
5W-30 Motor Oil

16.5 qt (15.6L)
16.0 qt (15.1L)
17.0 qt (16.1L)

Motorcraft Orange
VC-3DIL-B (US); CVCAntifreeze/Coolant 3DIL-B (Canada) / WSSPrediluted
M97B44-D2

19.5 qt (18.5L)

301

F150 (TF6) , enUSA

Capacities and Specifications
Item

Capacity

Front axle fluid
(Four-wheel
drive)

5,6

Rear axle fluid

Transmission /
parking brake linkages and pivots,
brake pedal shift
Transfer case
fluid
Four wheel drive
(Electronic Shift-

Ford part name or
equivalent

Ford part number / Ford
specification

3.5 pt (1.7L)

Motorcraft SAE
80W-90 Premium
Rear Axle Lubricant
(US); Motorcraft
SAE 80W-90
Premium Axle
Lubricant
(Canada)

XY-80W90-QL (US);
CXY-80W90-1L
(Canada) / WSPM2C197-A

5.5 pt (2.6L)

XY-75W140-QL (US);
Motorcraft SAE
CXY-75W140-1L
75W-140 Synthetic
(Canada) / WSL-M2C192Rear Axle Lubricant
A

—

1.5 qt (1.4L)

Motorcraft
Premium Long-Life
Grease

XG-1-E (US)

XL-12 (US); CXL-12
Motorcraft
(Canada) / ESP-M2C166Transfer Case Fluid
H

On-the-Fly)

Transfer case
fluid
Automatic four
wheel drive
(Torque On
Demand)

1.5 qt (1.4L)

Power steering Fill to between MIN
fluid (6.2L engine and MAX lines on
reservoir
only)

Automatic transmission fluid

8,9

3.7L engine
12.1 qt (11.7L)
5.0L, 6.2L and 3.5L
EcoBoost engines
13.1 qt (12.4L)

Motorcraft
MERCON LV

XT-10-QLVC (US); CXT10-LV12 (Canada)

Motorcraft
MERCON LV

XT-10-QLVC (US); CXT10-LV12 (Canada) /
MERCON LV

Motorcraft
MERCON LV

XT-10-QLVC (US); CXT10-LV12 (Canada) /
MERCON LV

302

F150 (TF6) , enUSA

Capacities and Specifications
Item

Capacity

Fill as required
Windshield
washer fluid

Ford part name or
equivalent

Motorcraft
Premium WindZC-32-B2 (US); CXC-37shield Wash
Concentrate with (A, B, D, and F) (Canada)
/
Bitterant (US);
Premium Quality
WSS-M14P19-A
Windshield Washer
Fluid (Canada)

26.0 gal (98.4L)
Standard

Fuel tank

—

Motorcraft R-134a
Refrigerant

YN-19 (US); CYN-16-R
(Canada) /
WSH-M17B19-A

Motorcraft PAG
Refrigerant
Compressor Oil

YN-12-D /

36.0 gal (136.2L)
Optional
1.50 lb (0.68 kg)
10

A/C Refrigerant

A/C Refrigerant
10

Compressor Oil

3.40 fl oz
(100.5 ml)

303

F150 (TF6) , enUSA

Ford part number / Ford
specification

Capacities and Specifications
Item

Capacity

Ford part name or
equivalent

Ford part number / Ford
specification

WSH-M1C231-B

304

F150 (TF6) , enUSA

Capacities and Specifications
1

Ford recommends using Motorcraft (Ford) DOT 4 LV High Performance Motor Vehicle
Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the
recommended fluid may cause degraded brake performance and not meet the Ford
performance standards. Keep brake fluid clean and dry. Contamination with dirt, water,
petroleum products or other materials may result in brake system damage and possible
failure.
2

The design of your engine allows for the use of Motorcraft engine oils or equivalent oils
that meet Ford specifications. It is also acceptable to use an engine oil of recommended
viscosity grade that meets API SN requirements and displays the API certification mark
for gasoline engines.
3

Do not use supplemental engine oil additives in your engine. They are unnecessary and
could lead to engine damage not covered by your Ford warranty.
Do not use API S category oils labeled as SN, SM, SL or lower category unless the label
also displays the API certification mark. These oils do not meet the requirements of the
engine and emission system.
4

Add the coolant type originally equipped in your vehicle.

Service refill capacity is determined by filling the axle to 1/4-9/16 inch (6-14 millimeter)
below the bottom of the filler hole with the vehicle on a level surface. Add 4 fl oz. (118
milliliters) of Additive Friction Modifier XL-3 (US) / CXL-3 (Canada) or equivalent meeting
Ford specification EST-M2C118-A, for complete fill of 8.8-inch Traction-Lok axles.
6

Filled with a synthetic rear axle lubricant, consider the rear axle on your vehicle filled for
life. You do not need to check or change the rear axle lubricant unless you suspect a leak.
Change the rear axle lubricant any time you have submerged the rear axle in water.
7

Service refill capacity is determined by filling the transfer case to the bottom of the filler
hole with the vehicle on a level surface.
8

Make sure the correct automatic transmission fluid is used. Transmission fluid
requirements are indicated on the dipstick blade or the dipstick handle. Before adding,
check the container to verify the fluid is of the correct type. Refer to your scheduled
maintenance information to determine the correct service interval.
Note: Automatic transmissions that require MERCON LV should only use MERCON LV fluid.
Use of any fluid other than the recommended fluid may cause transmission damage.
9

Indicates only approximate dry-fill capacity. Some applications may vary based on cooler
size and if equipped with an in-tank cooler. Use the indication on the dipstick, showing
the normal operating range, to determine the amount of transmission fluid and the fluid
level.
10

See the Warning below:
WARNING
The air conditioning refrigerant system contains refrigerant R-134a under high
pressure. Opening the air conditioning refrigerant system can cause personal injury.
Have the air conditioning refrigerant system serviced only by qualified personnel.

305

F150 (TF6) , enUSA

Audio System
AM and FM frequencies are established by
the Federal Communications Commission
(FCC) and the Canadian Radio and
Telecommunications Commission (CRTC).
Those frequencies are:
• AM: 530, 540-1700, 1710 kHz
• FM: 87.9-107.7, 107.9 MHz

GENERAL INFORMATION
Radio Frequencies and Reception
Factors

Radio Reception Factors

Distance and strength

The further you travel from an FM station, the weaker the
signal and the weaker the reception.

Terrain

Hills, mountains, tall buildings, bridges, tunnels, freeway
overpasses, parking garages, dense tree foliage and
thunderstorms can interfere with the reception.

Station overload

When you pass a ground-based broadcast repeating
tower, a stronger signal may overtake a weaker one and
result in the audio system muting.
Do not expose discs to direct sunlight or
heat sources for extended periods.

CD and CD Player Information
Note: CD units play commercially pressed
4.75-inch (12 centimeter) audio compact
discs only. Due to technical incompatibility,
certain recordable and re-recordable
compact discs may not function correctly
when used in Ford CD players.

MP3 Track and Folder Structure
Audio systems capable of recognizing and
playing MP3 individual tracks and folder
structures work as follows:
• There are two different modes for MP3
disc playback: MP3 track mode
(system default) and MP3 folder
mode.
• MP3 track mode ignores any folder
structure on the MP3 disc. The player
numbers each MP3 track on the disc
(noted by the .mp3 file extension) from
T001 to a maximum of T255. The
maximum number of playable MP3
files may be less depending on the
structure of the CD and exact model
of radio present.

Note: Do not insert CDs with homemade
paper (adhesive) labels into the CD player
as the label may peel and cause the CD to
become jammed. You should use a
permanent felt tip marker rather than
adhesive labels on your homemade CDs.
Ballpoint pens may damage CDs. Please
contact an authorized dealer for further
information.
Note: Do not use any irregularly shaped
discs or discs with a scratch protection film
attached.
Always handle discs by their edges only.
Clean the disc with an approved CD
cleaner only. Wipe it from the center of the
disc toward the edge. Do not clean in a
circular motion.
306

F150 (TF6) , enUSA

Audio System
•

•

MP3 folder mode represents a folder
structure consisting of one level of
folders. The CD player numbers all MP3
tracks on the disc (noted by the .mp3
file extension) and all folders
containing MP3 files, from F001
(folder) T001 (track) to F253 T255.
Creating discs with only one level of
folders helps with navigation through
the disc files.

In track mode, the system displays and
plays the structure as if it were only one
level deep (all .mp3 files play, regardless
of being in a specific folder). In folder
mode, the system only plays the .mp3 files
in the current folder.

AUDIO UNIT - VEHICLES WITH:
AM/FM

If you are burning your own MP3 discs, it is
important to understand how the system
reads the structures you create. While
various files may be present, (files with
extensions other than mp3), only files with
the .mp3 extension are played; other files
are ignored by the system. This enables
you to use the same MP3 disc for a variety
of tasks on your work computer, home
computer and your in-vehicle system.

WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any hand-held device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

E163157

307

F150 (TF6) , enUSA

Audio System
A

CLK: Press this button to switch the display between the clock and radio
frequency. To set the time, press and hold the button until the hours start to
flash. Press the arrow buttons (B) to adjust he hours, then repeat to set the
minutes. Press CLK again to exit clock mode.

Tune: Press these arrow buttons to manually search through the radio frequency
band. Press and hold for a fast search. In AUDIO mode, press the buttons to
adjust different sound settings.

AUDIO: Press this button to access settings for Treble, Middle, Bass, Fade and
Balance.

SEEK: Press this button to go to the previous or next strong station on the
frequency band.

Memory presets: Store your favorite radio stations. To store a radio station,
tune to the station, then press and hold a preset button until sound returns.

AM/FM: Press this button to select a frequency band.

VOL-PUSH: Press this button to switch the system off and on. Turn the control
to adjust the volume.
Note: Some features, such as Sirius satellite
radio, may not be available in your location.
Check with an authorized dealer.

AUDIO UNIT - VEHICLES WITH:
AM/FM/CD/SYNC/SATELLITE
RADIO
WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any hand-held device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

308

F150 (TF6) , enUSA

Audio System

E167071

Memory presets: Store your favorite stations for later access. When tuned to
any station, press and hold a preset button until sound returns and PRESET #
SAVED appears in the display. You can also save presets automatically by
using the autoset feature:
Press MENU repeatedly until AUTO PRESET ON/OFF appears in the display.
Use the SEEK buttons to turn AUTO PRESET on, and either wait five seconds
for the search to initiate or press OK to immediately start the search.
If you press another control within those five seconds, the search does not start.
The system fills the presets with the 10 strongest stations; the station stored
in preset 1 begins playing. If there are fewer than 10 strong stations, the system
stores the last one in the remaining presets.
Note: Autoset does not delete your original preset stations.
Note: In order to re-run the autoset features, you must first turn it off before
turning it back on.

CD slot: Insert a CD.

Eject: Press this button to eject a CD.

Arrow buttons: Press these buttons to make selections in MENU mode.

MENU: Press this button to access different audio features.
Compression brings the soft and loud CD passages together for a more
consistent listening level.
Shuffle plays the current CD tracks in random order.
RDS Radio allows you to search RDS-equipped stations for a certain category
of music such as CLASSIC, COUNTRY, JAZZ/RB or ROCK.

309

F150 (TF6) , enUSA

Audio System
SIRIUS allows you to access different satellite radio options.
F

CLOCK#: Press this button to set the time. Use the memory preset buttons to
enter the time, and then press OK.

PHONE: Press this button to access the phone features of the SYNC system.
See Using SYNC™ With Your Phone (page 327). If your vehicle is not equipped
with SYNC, the display reads NO PHONE.

SOUND: Press this button to access settings for Treble, Middle, Bass, Balance
and Fade. Use the SEEK or TUNE controls to change the settings.
Bass levels can be increased or decreased.
Treble levels can be increased or decreased.
Balance adjusts the sound between left and right speakers.
Fade adjusts the sound between the front and back speakers.
Speed Compensated Volume adjusts the volume to compensate for speed
and wind noise. You can set the system between off and +7.
All Seat Mode/Driver Seat Mode optimizes sound quality for the chosen
seating position.
DSP Mode (if equipped) allows you to choose between STEREO SURROUND
mode and STEREO mode.

SEEK:
In radio mode, select a frequency band and press one of these buttons. The
system stops at the first station it finds in that direction.
In Sirius mode, press one of these buttons to select the previous or next channel.
If you select a specific category (such as Jazz, Rock or News), use these buttons
to find the previous or next channel in the selected category.
In CD and MP3 modes, press one of these buttons to select the previous or next
track.

CD: Press this button to access CD and MP3 modes.
The disc begins to play where it left off. If no CD is loaded, NO DISC appears
in the display.
Press the SEEK buttons to access the previous or next track. Press and hold
the SEEK buttons to quickly reverse or fast-forward within the same track.

TUNE/OK/Play/Pause:
In radio mode, turn the control to search manually through the radio frequency
band.
In Sirius mode, turn the control to find the next or previous available satellite
radio station.
OK allows you to confirm commands with phone and media features.

310

F150 (TF6) , enUSA

Audio System
Play/Pause allows you to play or pause a track when listening to a CD.
L

AUX: Press this button to access media through your auxiliary input jack. See
Using SYNC™ With Your Media Player (page 345).

SIRIUS: Press this button to access different satellite radio modes.
Note: Sirius satellite radio is available only with a valid Sirius radio subscription.
Check with an authorized dealer for availability.

VOL/Power: Press this button to switch the system off and on. Turn it to adjust
the volume.

AM/FM: Press this button to select a frequency band.

CAT/FOLD:
In Sirius mode, press this button to switch between turning the most recently
selected satellite radio category off or on.
In MP3 mode, press this button, then use the SEEK buttons to access the
previous or next folder.

SCAN:
In radio mode, press this button to hear a brief sampling of all radio stations.
In Sirius mode, press this button to hear a brief sampling of all available
channels. If you select a specific category, press SCAN for a brief sampling of
all available channels within the selected category.
In CD and MP3 modes, press this button to hear a brief sampling of all tracks
on the current disc or MP3 folder.

DIRECT:
In radio mode, press this button to select the desired radio frequency (such as
93.9) using the memory preset numbers (0–9).
In Sirius mode, press this button to enter the desired channel (such as 002)
using the memory preset buttons. If you only enter one digit, and press OK, the
system goes to that channel. If you enter three digits, the system automatically
goes to that channel, if available. You may cancel your entry by pressing DIRECT.
If you enter an invalid station number, INVALID CHANNEL appears in the
display and the system continues playing the current station.
In CD mode, press this button to enter the desired track number using the
memory preset buttons. The system then begins playing that track.
In MP3 mode, press this button to enter a memory preset button of the desired
folder. The system advances to that specific folder.

TEXT:
MP3 mode, press this button to view Album (AL), Folder (FL), Song (SO) and
Artist (AR) in the display, if available.

311

F150 (TF6) , enUSA

Audio System
In text mode, sometimes the display requires additional text to show. When
the < / > indicator is on, press this button, then use the SEEK buttons to view
the additional text.
T

LOAD: This control is not operational. To load a CD, insert the disc, label side
up, into the CD slot.
Note: Some features, such as Sirius satellite
radio, may not be available in your location.
Check with an authorized dealer.

AUDIO UNIT - VEHICLES WITH:
AM/FM/CD/SYNC/SATELLITE
RADIO
WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any handheld device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

312

F150 (TF6) , enUSA

Audio System

E167070

RADIO: Press this button to listen to the radio or change radio frequency bands.
Press the function buttons below the radio screen to select different radio
functions.

CD: Press this button to listen to a CD. Press the function buttons below the
radio screen to select on-screen options of Repeat or Shuffle.

Number block:
In radio mode, store your favorite radio stations. To store a radio station, tune
to the station, then press and hold a preset button until sound returns.
In CD mode, select a track.
In phone mode, enter a phone number.

Function buttons: Select different functions of the audio system depending
on which mode you are in (such as Radio mode or CD mode).

TUNE:
In radio mode, turn the control to search the frequency band manually.
In satellite radio mode, turn the control to tune to the next or previous channel.

Reverse and Fast Forward; AM, FM, CD Seek:

313

F150 (TF6) , enUSA

Audio System
In radio mode, select a frequency band and press one of these buttons. The
system stops at the first station it finds in that direction. Press and hold one of
these buttons to move quickly in that direction to the next strong radio station
or memory preset.
In Sirius mode, press one of these buttons to select the previous or next channel.
If you select a specific category (such as Jazz, Rock or News), use these buttons
to find the previous or next channel in the selected category. Press and hold
one of these buttons to move quickly in that direction to the next channel or
category.
In CD mode, press one of these buttons to select the previous or next track.
Press and hold one of these buttons to move quickly in that direction within the
current track.
G

OK and arrow buttons: Press the up and down or left and right arrow buttons
to browse menu selections. Press OK to confirm menu selections.

Eject: Press this button to eject a CD.

Power and Volume: Press this button to switch the system off and on. Turn
it to adjust the volume.

CLOCK: Press this button to access the clock setting. Use the center arrow
controls to change the hours and minutes.

SOUND: Press this button to adjust settings for Treble, Middle, Bass, Balance
and Fade.

MENU: Press this button to access different audio system features. See Menu
Structure later in this section.

PHONE: Press this button to access the phone features of the SYNC system.
See Using SYNC™ With Your Phone (page 327).

AUX: Press this button to access your auxiliary input jack or switch between
devices you plug into the input jack or USB port. See Using SYNC™ With Your
Media Player (page 345).

SIRIUS: Press this button to listen to Sirius satellite radio.

314

F150 (TF6) , enUSA

Audio System
Note: The MyFord Touch system controls
most of the audio features. See MyFord
Touch™ (page 359).

AUDIO UNIT - VEHICLES WITH:
SONY AM/FM/CD
WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any hand-held device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

E163159

VOL and Power: Press this button to switch the system off and on. Turn it to
adjust the volume.

Eject: Press this button to eject a CD.

CD slot: Insert a CD.

TUNE: Turn this control to search through the radio frequency band manually.

Memory presets: Store your favorite radio stations. To store a radio station,
tune to the station, then press and hold a preset button until sound returns.

315

F150 (TF6) , enUSA

Audio System
F

Seek, Reverse and Fast Forward:
In radio mode, select a frequency band and press one of these buttons. The
system stops at the first station it finds in that direction.
In Sirius mode, press these buttons to select the previous or next channel. If a
specific category is selected (such as Jazz, Rock or News), use these buttons
to find the previous or next channel in the selected category.
In CD mode, press these buttons to select the previous or next track.

MEDIA: Press this button to access different audio modes, such as AM, FM and
A/V Input.
When HD Radio broadcasts are active, you
can access the following functions:

DIGITAL RADIO

When HD Radio broadcasts are active, you
can access the following functions:
• Scan allows you to hear a brief
sampling of all available stations. This
feature still works when HD Radio
reception is on, although it does not
scan for HD2-HD7 channels. You may
see the HD logo appear if the station
has a digital broadcast.
• Memory presets allow you to save an
active channel as a memory preset.
Touch and hold a memory preset slot
until the sound returns. There is a brief
mute while the radio saves the station.
Sound returns when finished. When
switching to an HD2 or HD3 memory
preset, the sound mutes before the
digital audio plays, because the system
has to reacquire the digital signal.

Note: HD Radio broadcasts are not
available in all markets.
HD Radio technology is the digital
evolution of analog AM/FM radio. Your
system has a special receiver that allows
it to receive digital broadcasts (where
available) in addition to the analog
broadcasts, it already receives. Digital
broadcasts provide a better sound quality
than analog broadcasts with free,
crystal-clear audio and no static or
distortion. For more information, and a
guide to available stations and
programming, please visit
www.hdradio.com.
When HD Radio is on and you tune to a
station broadcasting HD Radio technology,
you may notice the HD Radio logo on your
screen. When this logo is available, you
may also see Title and Artist fields
on-screen.

Note: As with any saved radio station, you
cannot access the saved station if your
vehicle is outside the station’s reception
area.

The multicast indicator appears in FM
mode (only) if the current station is
broadcasting multiple digital broadcasts.
The highlighted numbers signify available
digital channels where new or different
content is available. HD1 signifies the main
programming status and is available in
analog and digital broadcasts. Other
multicast stations (HD2 through HD7) are
only available digitally.
316

F150 (TF6) , enUSA

Audio System
HD Radio Reception and Station Troubleshooting
Potential reception issues

Reception area

If you are listening to a multicast station and you are on
the fringe of the reception area, the station may mute due
to weak signal strength.
If you are listening to HD1, the system switches back to
the analog broadcast until the digital broadcast is available
again. However, if you are listening to any of the possible
HD2-HD7 multicast channels, the station mutes and stays
muted unless it is able to connect to the digital signal
again.

Station blending

When the system first receives a station (aside from HD2HD7 multicast stations), it first plays the station in the
analog version. Once the receiver verifies the station is an
HD Radio station, it shifts to the digital version. Depending
on the station quality, you may hear a slight sound change
when the station changes from analog to digital. Blending
is the shift from analog to digital sound or digital back to
analog sound.

In order to provide the best possible
experience, use the contact form to report
any station issues found while listening to
a station broadcasting with HD Radio
technology. Independent entities own and
operate each station. These stations are
responsible for ensuring all audio streams
and data fields are accurate.

317

F150 (TF6) , enUSA

Audio System

Potential station issues
Issues

Echo, stutter, skip or repeat
in audio.
Increase or decrease in
audio volume.

Cause

Action

This is poor time alignment No action required. This is a
by the radio broadcaster.
broadcast issue.

Sound fading or blending in The radio is shifting between No action required. The
and out.
analog and digital audio.
reception issue may clear up
as you continue to drive.

There is an audio mute
delay when selecting HD2 or
HD3, multicast preset or
Direct Tune.

The digital multicast is not No action required. This is
available until the HD Radio normal behavior. Wait until
broadcast is decoded. Once the audio is available.
decoded, the audio is available.

Cannot access HD2 or HD3
multicast channel when
recalling a preset or from a
direct tune.

The previously stored
No action required. The
multicast preset or direct
station is not available in
tune is not available in your your current location.
current reception area.

Text information does not
match currently playing
audio.

Data service issue by the
radio broadcaster.

Fill out the station issue
form at website listed
below.

There is no text information Data service issue by the
shown for currently selected radio broadcaster.
frequency.

Fill out the station issue
form at website listed

HD2-HD7 stations not found Pressing Scan disables
when Scan is pressed.
HD2-HD7 channel search.

No action required. This is
normal behavior.

below.

http://www.ibiquity.com/automotive/report_radio_station_experiences

HD Radio Technology manufactured under
license from iBiquity Digital Corp. U.S. and
foreign patents. HD Radio and the HD and
HD Radio logos are proprietary trademarks
of iBiquity Digital Corp. Ford Motor
Company and iBiquity Digital Corp. are not
responsible for the content sent using HD
Radio technology. Content may be
changed, added or deleted at any time at
the station owner's discretion.

SATELLITE RADIO (IF EQUIPPED)
SIRIUS® broadcasts a variety of music,
news, sports, weather, traffic and
entertainment satellite radio channels. For
more information and a complete list of
SIRIUS satellite radio channels, visit
www.siriusxm.com in the United States,
www.sirius.ca in Canada, or call SIRIUS at
1-888-539-7474.

318

F150 (TF6) , enUSA

Audio System
Note: This receiver includes the eCos
real-time operating system. eCos is
published under the eCos License.

Satellite Radio Reception Factors
Potential satellite radio reception issues

Antenna obstructions

For optimal reception performance, keep the antenna
clear of snow and ice build-up and keep luggage and other
material as far away from the antenna as possible.

Terrain

Hills, mountains, tall buildings, bridges, tunnels, freeway
overpasses, parking garages, dense tree foliage and
thunderstorms can interfere with your reception.

Station overload

When you pass a ground-based broadcast-repeating
tower, a stronger signal may overtake a weaker one and
the audio system may mute.

Satellite radio signal interfer- Your display may show ACQUIRING . . . to indicate the
ence
interference and the audio system may mute.
SIRIUS satellite radio is a
subscription-based satellite radio service
that broadcasts a variety of music, sports,
news, weather, traffic and entertainment
programming. Your factory-installed
SIRIUS satellite radio system includes
hardware and a limited subscription term,
which begins on the date of sale or lease
of your vehicle. See an authorized dealer
for availability.

SIRIUS® Satellite Radio Service
Note: SIRIUS reserves the unrestricted right
to change, rearrange, add or delete
programming including canceling, moving
or adding particular channels, and its prices,
at any time, with or without notice to you.
Ford Motor Company shall not be
responsible for any such programming
changes.

For more information on extended
subscription terms (a service fee is
required), the online media player and a
complete list of SIRIUS satellite radio
channels, and other features, please visit
www.siriusxm.com in the United States,
www.sirius.ca in Canada, or call SIRIUS at
1-888-539-7474.

E142593

319

F150 (TF6) , enUSA

Audio System
Satellite Radio Electronic Serial
Number (ESN)

satellite radio mode, you can view this
number by pressing SIRIUS and memory
preset 1 at the same time, or tuning to
channel 0.

You need your ESN to activate, modify or
track your satellite radio account. When in

Troubleshooting
Radio display

Condition

Possible action

Acquiring

Radio requires more than
two seconds to produce
audio for the selected
channel.

Sat Fault/SIRIUS system
failure

There is an internal module If this message does not
clear shortly, or with an ignior system failure present.
tion key cycle, your receiver
may have a fault. See an
authorized dealer for service.

Invalid Channel

The channel is no longer
available.

Tune to another channel or
choose another preset.

Unsubscribed Channel

Your subscription does not
include this channel.

Contact SIRIUS at 1-888539-7474 to subscribe to
the channel, or tune to
another channel.

No Signal

The signal is lost from the
SIRIUS satellite or SIRIUS
tower to your vehicle
antenna.

The signal is blocked. When
you move into an open area,
the signal should return.

Updating

Update of channel
programming in progress.

No action required. The
process may take up to
three minutes.

Call SIRIUS 1-888-539-7474 Your satellite service is no
longer available.

No action required. This
message should disappear
shortly.

Contact SIRIUS at 1-888539-7474 to resolve
subscription issues.

None found. Check Channel All the channels in the
Use the channel guide to
Guide.
selected category are either turn off the Lock or Skip
skipped or locked.
function on that station.
Subscription Updated

SIRIUS has updated the
channels available for your
vehicle.

320

F150 (TF6) , enUSA

No action required.

Audio System
The auxiliary input jack allows you to
connect and play music from your portable
music player through your vehicle speakers.
You can use any portable music player
designed for use with headphones. Your
audio extension cable must have male
1/8th-inch (3.5 millimeter) connectors at
each end.

AUDIO INPUT JACK
WARNINGS
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any hand-held device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

For safety reasons, do not connect
or adjust the settings on your
portable music player while your
vehicle is moving.

3.
4.
5.

Store the portable music player in a
secure location, such as the center
console or the glove box, when your
vehicle is moving. Hard objects may
become projectiles in a collision or sudden
stop, which may increase the risk of serious
injury. The audio extension cable must be
long enough to allow the portable music
player to be safely stored while your
vehicle is moving.

E149149

321

F150 (TF6) , enUSA

Switch off the engine, radio and
portable music player. Set the parking
brake and put the transmission in
position P (vehicle with an automatic
transmission) or neutral (vehicle with
a manual transmission).
Plug the extension cable from the
portable music player into the auxiliary
input jack.
Switch the radio on. Select either a
tuned FM station or a CD.
Adjust the volume as desired.
Switch your portable music player on
and adjust its volume to half its
maximum level.
Press AUX until LINE or LINE IN
appears in the display. You should hear
music from your device even if it is low.
Adjust the volume on your portable
music player until it reaches the volume
level of the FM station or CD. Do this
by switching back and forth between
the AUX and FM or CD controls.

Audio System
USB PORT (IF EQUIPPED)

E149148

The USB port allows you to plug in media
playing devices, memory sticks and charge
devices (if supported). See SYNC™ (page
323).

MEDIA HUB (IF EQUIPPED)
The media hub is located in a
compartment inside the center console or
in under an access door, in front of the
gearshift.

E163162

A/V inputs

SD card slot

USB ports

See MyFord Touch™ (page 359).

322

F150 (TF6) , enUSA

SYNC™
GENERAL INFORMATION

E142598

•

SYNC is an in-vehicle communications
system that works with your
Bluetooth-enabled cellular phone and
portable media player. This allows you to:
• Make and receive calls.
• Access and play music from your
portable music player.
• Use 911 Assist, Vehicle Health Report
and SYNC Services (Traffic, Directions
*
& Information).
•
•
•
•

•
*

These features require activation.

Make sure that you review your device's
manual before using it with SYNC.

Support
The SYNC support team is available to
help you with any questions you cannot
answer on your own.

Use applications, such as Pandora and
Stitcher, via SYNC AppLink.
Access phonebook contacts and music
using voice commands.
Stream music from your connected
phone.
Text message.

Monday-Saturday, 8:30am-9:00pm EST.
Sunday, 10:30am-7:30pm EST.
In the United States, call 1-800-392-3673.
In Canada, call 1-800-565-3673.

323

F150 (TF6) , enUSA

Use the advanced voice recognition
system
Charge your USB device (if your device
supports this).

SYNC™
Times are subject to change due to
holidays.

When using SYNC:
• Do not operate playing devices if the
power cords or cables are broken, split
or damaged. Place cords and cables
out of the way, so they do not interfere
with the operation of pedals, seats,
compartments or safe driving abilities.
• Do not leave playing devices in your
vehicle during extreme conditions as it
could cause them damage. See your
device's manual for further information.
• Do not attempt to service or repair the
system. See an authorized dealer.

SYNC Owner Account
Why do I need a SYNC owner account?
• Required to activate Vehicle Health
Report and to view the reports online.
• Required to activate the
subscription-based SYNC Services and
to personalize your Saved Points and
Favorites.
• Essential for keeping up with the latest
software downloads available for
SYNC.
• Access to customer support for any
questions you may have.

Privacy Information
When a cellular phone is connected to
SYNC, the system creates a profile within
your vehicle that is linked to that cellular
phone. This profile is created in order to
offer you more cellular features and to
operate more efficiently. Among other
things, this profile may contain data about
your cellular phone book, text messages
(read and unread), and call history,
including history of calls when your cellular
phone was not connected to the system.
In addition, if you connect a media device,
the system creates and retains an index of
supported media content. The system also
records a short development log of
approximately 10 minutes of all recent
system activity. The log profile and other
system data may be used to improve the
system and help diagnose any problems
that may occur.

Driving Restrictions
For your safety, certain features are
speed-dependent and restricted when your
vehicle is traveling over 3 mph (5 km/h).

Safety Information
WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any hand-held device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

The cellular profile, media device index,
and development log will remain in the
vehicle unless you delete them and are
generally accessible only in the vehicle
when the cellular phone or media player
is connected. If you no longer plan to use
the system or the vehicle, we recommend
you perform a Master Reset to erase all
stored information.

324

F150 (TF6) , enUSA

SYNC™
System data cannot be accessed without
special equipment and access to the
vehicle's SYNC module. Ford Motor
Company and Ford of Canada will not
access the system data for any purpose
other than as described absent consent, a
court order, or where required by law
enforcement, other government
authorities, or other third parties acting
with lawful authority. Other parties may
seek to access the information
independently of Ford Motor Company and
Ford of Canada. For further privacy
information, see the sections on 911 Assist,
Vehicle Health Report, and Traffic,
Directions and Information.

USING VOICE RECOGNITION
This system helps you control many
features using voice commands. This
allows you to keep your hands on the
wheel and focus on what is in front of you.

Initiating a Voice Session
Push the voice icon. A tone
sounds and Listening appears in
E142599
the display. Say any of the
following:

Say

If You Want To

"Bluetooth audio"

Stream audio from your phone.

"Cancel"

Cancel the requested action.

"Line in"

Access the device connected to the auxiliary input jack.

"Mobile apps"

Access mobile applications.

"Phone"
"Services"

Make calls.
Access the SYNC Services portal.

"SYNC"

Return to the main menu.

"USB"
"Vehicle health report"

Access the device connected to your USB port.
*

Run a vehicle health report.

"Voice settings"

Adjust the level of voice interaction and feedback.

"Help"

Hear a list of voice commands available in the current
mode.

This is an optional feature and available in the United States only.

325

F150 (TF6) , enUSA

SYNC™
System Interaction and Feedback

The default setting is to a higher level of
interaction in order to help you learn to use
the system. You can change these settings
at any time.

The system provides feedback through
audible tones, prompts, questions and
spoken confirmations depending on the
situation and the chosen level of
interaction (voice settings). You can
customize the voice recognition system to
provide more or less instruction and
feedback.

Adjusting the Interaction Level

E142599

Push the voice icon. Say "Voice
settings" when prompted, then
any of the following:

When you say:

The system:

"Interaction mode standard"

Provides more detailed interaction and
guidance.

"Interaction mode advanced"

Provides less audible interaction and more
tone prompts.

The system defaults to the standard interaction mode.
Confirmation prompts are short questions
the system asks when it is not sure of your
request or when there are multiple possible
responses to your request. For example,
the system may ask "Phone, is that
correct?". If turned off, the system simply
makes a best guess as to what you
requested and may ask you to confirm
settings.
When you say:

The system:

"Confirmation prompts off"

Makes a best guess from the command;
you may still occasionally be asked to
confirm settings.

"Confirmation prompts on"

Clarifies your voice command with a short
question.
For example, say "Say 1 after the tone to
call John Doe at home. Say 2 after the tone
to call Johnny Doe on mobile. Say 3 after
the tone to call Jane Doe at home." You
could also say "Say 1 after the tone to play
John Doe, Say 2 after the tone to play
Johnny Doe."

The system creates candidate lists when
it has the same confidence level of several
options based on your voice command.
When turned on, it may prompt you with
as many as four possibilities for
clarification.

326

F150 (TF6) , enUSA

SYNC™

When you say:

The system:

"Media candidate lists off"

Makes a best guess from the media
candidate list. You may still occasionally
be asked questions.

"Media candidate lists on"

Clarifies your voice command for media
candidates.

"Phone candidate lists off"

Makes a best guess from the phone
candidate list. You may still occasionally
be asked questions.

"Phone candidate lists on"

Clarifies your voice command for phone
candidates

Helpful Hints
•

•

•
•

USING SYNC™ WITH YOUR
PHONE

Make sure the interior of your vehicle is
as quiet as possible. Wind noise from
open windows and road vibrations may
prevent the system from correctly
recognizing spoken commands.
After pressing the voice icon, wait until
after the tone sounds and Listening
appears before saying a command. Any
command spoken before this does not
register with the system.
Speak naturally, without long pauses
between words.
At any time, you can interrupt the
system while it is speaking by pressing
the voice icon.

Hands-free calling is one of the main
features of SYNC. While the system
supports a variety of features, many are
dependent on your cellular phone's
functionality. At a minimum, most cellular
phones with Bluetooth wireless technology
support the following functions:
• Answering an incoming call.
• Ending a call.
• Using privacy mode.
• Dialing a number.
• Redialing.
• Call waiting notification.
• Caller ID.
Other features, such as text messaging
using Bluetooth and automatic phonebook
download, are phone-dependent features.
To check your phone's compatibility, see
your phone's manual and visit
www.SYNCMyRide.com,
www.SYNCMyRide.ca or
www.syncmaroute.ca.

327

F150 (TF6) , enUSA

SYNC™
Pairing a Phone for the First Time

Note: SYNC can support downloading up
to approximately 1000 entries per
Bluetooth-enabled cellular phone.

2.
3.

Note: Make sure to switch on the ignition
and the radio. Put the transmission in
position P.

Note: To scroll through the menus, press
the up and down arrows on your audio
system.

Wirelessly pairing your phone with SYNC
allows you to make and receive hands-free
calls.

Press the phone button. When the
display indicates there is no phone
paired, press OK.
2. When Find SYNC appears in the
display, press OK.
3. Put your phone into Bluetooth
discovery mode. See your device's
manual if necessary.
4. When prompted on your phone's
display, enter the six-digit PIN provided
by SYNC in the radio display. The
display indicates when the pairing is
successful.

The system then prompts with questions,
such as if you would like to set the current
phone as the primary phone (the phone
SYNC automatically tries to connect with
first upon vehicle start-up) and download
your phone book.

Phone Voice Commands
Press the voice icon and say "Phone". Say
any of the following:
"PHONE"

Depending on your phone's capability and
your market, the system may prompt you
with questions, such as setting the current
phone as the primary phone (the phone
SYNC automatically tries to connect with
first upon vehicle start-up) and
downloading your phonebook.

"Call "

1,2

"Call at home"
"Call at work"

1,2

"Call in office"

Pairing Subsequent Phones

1,2

"Call on mobile OR cell"

Note: Make sure to switch on the ignition
and the radio. Put the transmission in
position P.

"Call on other"

Note: To scroll through the menus, press
the up and down arrows on your audio
system.

1,2

"Call history incoming"
2

"Call history missed"

328

F150 (TF6) , enUSA

Press the phone button, and then scroll
to System Settings. Press OK.
Scroll to Bluetooth Devices. Press OK.
Scroll to Add Bluetooth Device. Press
OK.
When Find SYNC appears in the
display, press OK.
Put your phone into Bluetooth
discovery mode. See your phone's
manual if necessary.
When prompted on your phone's
display, enter the six-digit PIN provided
by SYNC in the radio display. The
display indicates when the pairing is
successful.

SYNC™
"PHONE"
"DIAL"
2

"Call history outgoing"
"Connections"
"Dial"

"411 (four-one-one)", "911" (nine-oneone)

"700" (seven hundred)

1,3

"800" (eight hundred)

"Go to privacy"

"900" (nine hundred)

"Hold"

"Pound" (#)

"Join"
"Menu"

"Number <0-9>"
2,4

"Phone book "

"Asterisk" (*)
2

"Clear" (deletes all entered digits)
"Delete" (deletes one digit)

"Phone book at home"

"Plus"

"Phone book at office"
"Phone book at work"

"Star"

Note: To exit dial mode, press and hold the
phone button or press MENU to go to the
phone menu.

"Phone book on mobile OR
2

cell"

"Phone book on other"

"MENU"

This command does not require you to
say "Phone" first.

"(Phone) connections"
"(Phone) settings (message) notification
off"

This command is not available until
phone information is completely
downloaded using Bluetooth.
3

See Dial table below.

See Menu table below.

"(Phone) settings (message) notification
on"
"(Phone) settings (set) phone ringer"
"(Phone) settings (set) ringer 1"

Phone book commands: When you ask
SYNC to access things such as a
phonebook name or number, the
requested information appears in the
display to view. Press the phone button
and say, "Call" to call the contact.

"(Phone) settings (set) ringer 2"
"(Phone) settings (set) ringer 3"
"(Phone) settings (set) ringer off"
"Battery"
"Phone name"

329

F150 (TF6) , enUSA

SYNC™
Receiving Calls

"MENU"

When receiving a call, you can:
• Answer the call by pressing the phone
button.
• Reject the call by pressing and holding
the phone button.
• Ignore the call by doing nothing.

"Signal"
"Text message inbox"
Words in ( ) are optional and do not have
to be spoken for the system to understand
the command.

Making Calls

Phone Options during an Active
Call

Press the voice icon and when prompted
say:

During an active call, you have more menu
features that become available, such as
putting a call on hold or joining calls. Use
the arrow buttons to scroll through the
menu options.

Say "Call " or "Dial", then the
desired number.
2. When the system confirms the number,
say, "Dial" again to initiate the call.

1. Press MENU during an active call.
2. After selecting Active Call Menu, press
OK.
3. Scroll to cycle through the following
options:

To erase the last spoken digit, say, "Delete"
or press the left arrow button. To erase all
spoken digits, say "Clear" or press and hold
the left arrow button.
To end the call, press and hold the phone
button.
When you select:

You can:

Mute Call?

Mute the call.

Privacy

Switch a call from an active hands-free environment to
your cellular phone for a more private conversation.
Press OK when Privacy on/off appears. (The display
indicates In Privacy and the system transfers your call.)

Call Hold

Put an active call on hold.
Press OK when Hold on/off appears. To answer another
call at this time, press the phone button.

Enter Tones

Enter "tones", such as numbers for passwords.
Scroll until the desired number appears in the display, then
press OK; a tone sounds as confirmation. Repeat as
necessary.

Join Calls

Join two separate calls. (SYNC supports a maximum of
three callers on a multiparty call or conference call.)
1. Press the phone button.

330

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

2. Access the desired contact through SYNC or use voice
commands to place the second call. Once actively in the
second call, press MENU.
3. Scroll to Join Calls, and press OK. Press OK again when
Join Calls? appears.
Phonebook

Access your phonebook contacts.
1. Press OK to select, and then scroll through your phonebook contacts.
2. Press OK again when the desired selection appears in
the display.
3. Press the phone button.

Call History

Access your call history log.
1. Press OK to select, then scroll through your call history
options (incoming, outgoing or missed).
2. Press OK when the desired selection appears in the
display.
3. Press the phone button to call the selection.

Return

Exit the current menu.
1.

Press the phone button to enter the
phone menu.
2. Scroll to cycle through:

Accessing Features through the
Phone Menu
SYNC's phone menu allows you to redial
a number, access your call history and
phonebook and sends text messages as
well as access phone and system settings.
You can also access advanced features,
such as 911 Assist, Vehicle Health Report
and SYNC Services.
When you select:

Phone Redial
Call History

You can:

Redial the last number called (if available). Press OK to
select, and then press OK again to confirm.
Access any previously dialed, received or missed calls after
you connect your Bluetooth-enabled phone to SYNC.
1. Press OK to select.
2. Scroll to select from Call History Incoming, Call History
Outgoing or Call History Missed. Press OK to make your
selection.
3. Press OK or the phone button to call the desired selection.

331

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

Note: The system attempts to automatically re-download
your phonebook and call history each time your phone
connects to SYNC (if the auto download feature is on and
your Bluetooth-enabled cellular phone supports this
feature).
Access and call any contacts in your previously downloaded phonebook.
1. Press OK to confirm and enter. If your phonebook has
fewer than 255 listings, they appear alphabetically in flat
file mode. If there are more than 255 entries, the system
organizes them into alphabetical categories.
2. Scroll until the desired contact appears, then press OK.
3. Press OK or the phone button.

1,2

Phonebook

Send, download and delete text messages.

Text Message

Phone Settings

View your phone's status, set ring tones, select your
message notification, change phone book entries and
automatically download your cellular phone among other
features.

Access the SYNC Services portal where you can request
various types of information, traffic reports and directions.

SYNC Services

Place an emergency call to a 911 operator for you after an
accident, when used properly.

911 Assist

Vehicle Health Report

Create and receive a diagnostic report card on your vehicle.

Mobile Apps

Interact with SYNC-capable mobile applications on your
smartphone.

System Settings

Access Bluetooth Devices menu listings (Add, Connect,
Set as Primary, On and Off, Delete) as well as Advanced
menu listings (prompts, languages, defaults, master reset,
install application and system information).

Exit Phone Menu

Exit the phone menu by pressing OK.

This is a phone-dependent feature.

This is a phone-dependent and speed-dependent feature.

This is an optional feature and available in the United States only.

This is an optional feature and available in the United States and Canada only.

332

F150 (TF6) , enUSA

SYNC™
Text Messaging

Sending, Downloading and Deleting
Your Text Messages

Note: This is a phone-dependent feature.

Note: Forwarding a text message is a
speed-dependent feature and is only
available when your vehicle is traveling at 3
mph (5 km/h) or less.

SYNC allows you to receive, send,
download and delete text messages. The
system can also read incoming text
messages to you so that you do not have
to take your eyes off the road.

Note: You can only have one recipient per
text message.

Receiving a Text Message

Text messaging is a phone-dependent
feature. If your phone is compatible, SYNC
allows you to receive, send, download and
delete text messages.

Note: This is a phone-dependent feature.
Your phone must support downloading text
messages using Bluetooth to receive
incoming text messages.

1. Press the phone button.
2. Scroll to Text Message, and then press
OK.

When a new message arrives, an audible
tone sounds and the display indicates you
have a new message. You have these
options:
• Press the voice button, wait for the
prompt and say "Read message" to
have SYNC read the message to you.
• Press OK to receive and open the text
message or do nothing and the
message goes into your text message
inbox. Press OK again and SYNC reads
your message aloud as you are not able
to view the message. You can then also
choose to reply or forward the
message.
• Press OK and scroll to choose
between:
• Reply to Text Message: Press OK
to access and then scroll through
the list of pre-defined messages to
send.
• Forward Text Message: Press OK
to forward the message to anyone
in your Phonebook or Call History.
You can also choose Enter Number.

Scroll to select from the following options:
• Send Text Message? allows you to
send a new text message based on a
pre-defined set of 15 messages.
• Download Unread Msgs allows you
to download your unread messages
(only) to SYNC. To download the
messages, press OK to select. The
display indicates that it is downloading
your messages. When it is complete,
SYNC takes you to your inbox.
• Delete All Messages? allows you to
delete current text messages from
SYNC (not your phone). To delete the
messages, press OK to select. The
display indicates when it is finished
deleting all your text messages. SYNC
returns you to the text message menu.
• Return exits the current menu when
you press OK.
If you select Send Text Message?:
1.

Press OK to select. If the system
detects your phone does not support
this feature, Unsupported appears in
the display and SYNC returns to the
main menu.
2. Scroll to cycle through the message
options in the following chart.
333

F150 (TF6) , enUSA

SYNC™
3. Press OK when the desired selection
is in the display.
4. Enter the name of the recipient. Scroll
to cycle through Phonebook or Call
History entries. You can also select
Enter Number to say the desired
number.
5. Press OK to enter the desired menu
and scroll to select the specific
contact.
6. Press OK when the contact appears
and press OK again to confirm when
the system asks if you would like to
send the message. The system sends
each text message with the following
signature: "This message was sent
from my ".

Pre-defined text message options

No
Why?
Thanks
Where R you?
I need more directions
I love you
Too funny
Can't wait to see you
I'm stuck in traffic

Accessing Your Phone Settings

Pre-defined text message options

These are phone-dependent features. Your
phone settings allow you to access and
adjust features such as your ring tone, text
message notification, modify your
phonebook and set up automatic
download.

Can't talk right now
Call me
Call U later
Be there in 10 minutes

1. Press the phone button.
2. Scroll to Phone Settings, and then
press OK.
3. Scroll to select from the following
options:

Be there in 20 minutes
Yes

When you select:

You can:

Phone Status

See the provider, name, signal power, battery power and
roaming status of your connected phone.
Press OK to select and scroll to view the information.
When done, press OK again to return to the phone status
menu.

Set Ringer

Select which ring tone sounds during an incoming call (one
of the system's or your phone's).
1. Press OK to select and scroll to hear Ringer 1, Ringer 2,
Ringer 3 and Phone Ringer.
2. Press OK to select.

334

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

If your phone supports in-band ringing, your phone's ring
tone plays when you choose Phone Ringer.
Message Notification

Have the option of hearing an audible tone to notify you
when a text message arrives.
1. Press OK to select and scroll between Message Notification On and Message Notification Off.
2. Press OK to select.

Modify Phonebook

Modify the contents of your phonebook (such as add,
delete or download). Press OK to choose between:
Add Contacts: Press OK to add more contacts from your
phone book. Push the desired contact(s) on your phone.
See your phone's manual on how to push contacts.
Delete Phonebook: Press OK to delete the current phone
book and call history. When Delete Phonebook appears,
press OK to confirm. SYNC takes you back to the Phone
Settings menu.
Download Phonebook: Press OK to select, then and press
OK again when Confirm Download? appears.

Auto Download

Automatically download your phone book each time your
*

phone connects to SYNC.
Press OK to select. When Auto Download On? appears,
press OK to have your phonebook automatically down**

loaded each time.
Select Off if you do not want to download your phonebook
every time your phone connects to SYNC. Your phonebook,
call history and text messages can only be accessed when
your specific phone is connected to SYNC.
Return
*

Exit the current menu.

Downloading times are phone-dependent and quantity-dependent.

When Auto Download is on, it automatically deletes any changes, additions or deletions
saved since your last download.
Bluetooth Devices

System Settings

The Bluetooth Devices menu allows you
to add, connect and delete devices, set a
phone as primary as well as turn your
Bluetooth feature on and off.

This menu provides access to your
Bluetooth Devices and Advanced menu
features. Use the arrow buttons to scroll
through the menu options.

335

F150 (TF6) , enUSA

SYNC™
3. Scroll to Bluetooth Devices. Press OK.

Press the phone button to enter the
phone menu
2. Scroll to System Settings. Press OK.

4. Scroll to select from the following
options:

If you select:

You can:

Add Bluetooth Device

See Using SYNC™ With Your Phone (page 327).

Connect Bluetooth Device

Connect a previously paired Bluetooth-enabled phone.
1. Press OK to select and view a list of previously paired
phones.
2. Scroll until you find the desired device, and then press
OK to connect the phone.

Set as Primary Phone

Set a previously paired phone as your primary phone.
Press OK to select and scroll to select the desired phone.
Press OK to confirm.
SYNC attempts to connect with the primary phone at every
ignition cycle. When you select a phone as a primary phone,
it appears first in the list and the system marks it with an
asterisk.

Set Bluetooth

Turn the Bluetooth feature on and off.
Press OK and scroll to toggle between On and Off. Make
a selection, and then press OK.
Setting Bluetooth to off disconnects all Bluetooth devices
and turns off all Bluetooth features.

Delete Device

Delete a paired phone.
Press OK and scroll to select the device. Press OK to
confirm.

Delete All Devices

Delete all previously paired phones (and all information
originally saved with those phones).
Press OK to select.

Return

Exit the current menu.

This is a speed-dependent feature.

You can only connect one device at a time. When another phone is connected, the
previous one is disconnected.

336

F150 (TF6) , enUSA

SYNC™
Advanced

Press the phone button to enter the
phone menu
2. Scroll to System Settings. Press OK.
3. Scroll to Advanced. Press OK.
4. Scroll to select from the following
options:

The Advanced menu allows you to access
and set prompts, languages, defaults,
perform a master reset, install an
application and view system information.

If you select:

You can:

Prompts

Get help from SYNC by using questions, helpful hints or
asking you for a specific action. To turn these prompts on
or off:
1. Press OK to select and scroll to select between On and
Off.
2. Press OK when the desired selection appears in the
display. SYNC takes you back to the Advanced menu.

Languages

Choose between English, Français and Español. Once
selected, all of the radio displays and prompts are in the
selected language.
1. Press OK to select and then scroll through the languages.
2. Press OK when the desired selection appears in the
display. If you change the language setting, the display
indicates that the system is updating. When complete,
SYNC takes you back to the Advanced menu.

Factory Defaults

Return to the factory default settings. This selection does
not erase your indexed information (phonebook, call
history, text messages and paired devices).
1. Press OK to select and then press OK again when
Restore Defaults? appears in the display.
2. Press OK to confirm.

Master Reset

Completely erase all information stored on SYNC
(phonebook, call history, text messages and paired
devices) and return to the factory default settings.
Press OK to select. The display indicates when complete
and SYNC takes you back to the Advanced menu.

Install Application?

Install applications you have downloaded.
Press OK and scroll to select. Press OK to confirm.

Delete All Devices

Delete all previously paired phones (and all information
originally saved with those phones).
Press OK to select.

System Info

Access the Auto Version number as well as the FDN
number.

337

F150 (TF6) , enUSA

SYNC™
If you select:

You can:

Press OK to select.
MAP Profile

This is a Bluetooth component, which can further help
your phone with the exchange of text messages.

Return

Exit the current menu.
WARNINGS

SYNC™ APPLICATIONS AND
SERVICES (IF EQUIPPED)

Do not wait for 911 Assist to make an
emergency call if you can do it
yourself. Dial emergency services
immediately to avoid delayed response
time which could increase the risk of
serious injury or death after a crash. If you
do not hear 911 Assist within five seconds
of the crash, the system or phone may be
damaged or non-functional.

In order for the following features to work,
your cellular phone must be compatible
with SYNC. To check your phone's
compatibility, visit www.SYNCMyRide.com,
www.SYNCMyRide.ca or
www.syncmaroute.ca.
*
• SYNC Services : Provides access to
traffic, directions and information such
as travel, horoscopes, stock prices and
more.
• 911 Assist: Can alert 911 in the event of
an emergency.
*
• Vehicle Health Report : Provides a
diagnostic and maintenance report
card of your vehicle.

Always place your phone in a secure
location in your vehicle so it does not
become a projectile or get damaged
in a crash. Failure to do so may cause
serious injury to someone or damage the
phone which could prevent 911 Assist from
working properly.
Note: The SYNC 911 Assist feature must be
set on before the incident.

This is an optional feature and available
in the United States only.

Note: Before setting this feature on, make
sure that you read the 911 Assist Privacy
Notice later in this section for important
information.

911 Assist

Note: If any user turns 911 Assist on or off,
that setting applies for all paired phones. If
911 Assist is turned off, either a voice
message plays or a display message (or
icon) comes on (or both) when your vehicle
is started after a previously paired phone
connects.

WARNINGS
Unless the 911 Assist setting is set on
before a crash, the system will not
dial for help which could delay
response time, potentially increasing the
risk of serious injury or death after a crash.

Note: Every phone operates differently.
While SYNC 911 Assist works with most
cellular phones, some may have trouble
using this feature.

338

F150 (TF6) , enUSA

SYNC™
•

If a crash deploys an airbag (excluding
knee airbags and rear inflatable safety
belts [if equipped]) or activates the fuel
pump shut-off, your SYNC-equipped
vehicle may be able to contact emergency
services by dialing 911 through a paired and
connected Bluetooth-enabled phone. You
can learn more about the 911 Assist
feature, visit www.SYNCMyRide.com,
www.SYNCMyRide.ca or
www.syncmaroute.ca.

•

See Supplementary Restraints System
(page 39). Important information about
airbag deployment is in this chapter.
See Roadside Emergencies (page 215).
Important information about the fuel pump
shut-off is in this chapter.

In the Event of a Crash
Not all crashes will deploy an airbag or
activate the fuel pump shut-off (the
triggers for 911 Assist). If a connected cell
phone sustains damage or loses its
connection to SYNC during a crash, SYNC
will search for and try to connect to a
previously paired cell phone; SYNC will
then attempt to call the emergency
services.

Setting 911 Assist On
1.
2.
3.
4.
5.

Press the phone button to enter the
phone menu.
Scroll to select 911 Assist.
Press OK to confirm and enter the 911
Assist menu.
Scroll to select between On and Off.
Press OK when the desired option
appears in the radio display. Set On or
Set Off appears in the display as
confirmation.

Before making the call:
• SYNC provides a short window of time
(about 10 seconds) to cancel the call.
If you fail to cancel the call, SYNC
attempts to dial 911.
• SYNC says the following, or a similar
message: "SYNC will attempt to call
911, to cancel the call, press Cancel on
your screen or press and hold the
phone button on your steering wheel."

Off selections include:
• Off with reminder: Provides a display
and voice reminder at phone
connection at vehicle start.
• Off without reminder: Provides a
display reminder only without a voice
reminder at phone connection.

If you do not cancel the call, and SYNC
makes a successful call, a pre-recorded
message plays for the 911 operator, and
then the occupant(s) in your vehicle is able
to talk with the operator. Be prepared to
provide your name, phone number and
location immediately, because not all 911
systems are capable of receiving this
information electronically.

To make sure that 911 Assist works
properly:
• SYNC must be powered and working
properly at the time of the incident and
throughout feature activation and use.
• The 911 Assist feature must be set on
before the incident.

339

F150 (TF6) , enUSA

You must pair and connect a
Bluetooth-enabled and compatible
cell phone to SYNC.
A connected Bluetooth-enabled phone
must have the ability to make and
maintain an outgoing call at the time
of the incident.
A connected Bluetooth-enabled phone
must have adequate network coverage,
battery power and signal strength.
The vehicle must have battery power
and be located in the U.S., Canada or
in a territory in which 911 is the
emergency number.

SYNC™
Note: Your Vehicle Health Report feature
requires activation before use. Visit
www.SYNCMyRide.com to register. There
is no fee or subscription associated with
Vehicle Health Report, but you must register
to use this feature.

911 Assist May Not Work If
•
•
•

Your cellular phone or 911 Assist
hardware sustains damage in a crash.
The vehicle's battery or the SYNC
system has no power.
The phone(s) thrown from your vehicle
are the ones paired and connected to
the system.

Note: This feature may not function
properly if you have enabled caller ID
blocking on your cellular phone. Before
running a report, review the Vehicle Health
Report Privacy Notice.

911 Assist Privacy Notice
When you turn on 911 Assist, it may
disclose to emergency services that your
vehicle has been in a crash involving the
deployment of an airbag or activation of
the fuel pump shut-off. Certain versions or
updates to 911 Assist may also be capable
of electronically or verbally disclosing to
911 operators your vehicle location or other
details about your vehicle or crash to assist
911 operators to provide the most
appropriate emergency services. If you do
not want to disclose this information, do
not turn the feature on.

Note: In order to allow a break-in period for
your vehicle, you may not be able to create
a Vehicle Health Report until your vehicle
odometer has reached 200 miles.
Note: Cellular phone and SMS charges may
apply when making a report.
Register for Vehicle Health Report and set
your report preferences at
www.SYNCMyRide.com. After registering,
you can request a Vehicle Health Report
(inside your vehicle). Return to your
account at www.SYNCMyRide.com to view
your report. You can also choose for SYNC
to remind you automatically to run reports
at specific mileage intervals.

Vehicle Health Report
WARNING

The system allows you to check your
vehicle's overall health in the form of a
diagnostic report card. The vehicle health
report contains valuable information such
as:
• Vehicle diagnostic information
• Scheduled maintenance
• Open recalls and Field Service Actions
• Items noted during vehicle inspections
by an authorized dealer that still need
servicing.

Always follow scheduled
maintenance instructions, regularly
inspect your vehicle, and seek repair
for any damage or problem you suspect.
Vehicle Health Report supplements, but
cannot replace, normal maintenance and
vehicle inspection. Vehicle Health Report
only monitors certain systems
electronically monitored by your vehicle
and will not monitor or report the status
of any other system, (such as brake lining
wear). Failure to perform scheduled
maintenance and regularly inspect your
vehicle may result in vehicle damage and
serious injury.

You can run a report (after your vehicle has
been running a minimum of 60 seconds)
by pressing the voice button and saying
"Vehicle health report", or pressing the
phone button.

Note: This feature is only available in the
United States.

To run a report using the phone button:

340

F150 (TF6) , enUSA

SYNC™
3. Scroll to select from the following
options:

Press the phone button to enter phone
menu.
2. Scroll to select Vehicle Health, and
then press OK.

Vehicle health report options

User Preferences: Press OK Automatic Reports: Press OK to and select On or Off.
to select and enter the
Select On to have SYNC automatically prompt you to run
menu. Scroll to select from: a health report at certain mileage intervals.*
Mileage Intervals: Press OK. Scroll to select between
5000, 7500 or 10000-mile intervals and press OK to make
your selection.
Return: Press OK to exit the menu.
Run Report?

Press OK for SYNC to run a health report of your vehicle's
diagnostic systems and send the results to Ford where it
combines with scheduled maintenance information, open
recalls and other field service actions and vehicle inspection items that still need servicing from an authorized
dealer.

You must first turn this feature on before you can select the desired mileage interval.

Note: SYNC Services varies by trim level
and model year and may require a
subscription. Traffic alerts and turn-by-turn
directions available in select markets.
Message and data rates may apply. Ford
Motor Company reserves the right to change
or discontinue this product service at any
time without prior notification or incurring
any future obligation.

information, do not run the feature or set
up your Vehicle Health Report profile at
www.SYNCMyRide.com. See
www.SYNCMyRide.com (Vehicle Health
Report Terms and Conditions, and Privacy
Statement) for more information.

SYNC Services: Traffic, Directions
& Information (TDI) (If Equipped,
Unites States Only)

Vehicle Health Report Privacy Notice

When you create a Vehicle Health Report,
Ford Motor Company may collect your
cellular phone number (to process your
report request) and diagnostic information
about your vehicle. Certain versions or
updates to Vehicle Health Report may also
collect more vehicle information. Ford may
use your vehicle information it collects for
any purpose. If you do not want to disclose
your cellular phone number or vehicle

341

F150 (TF6) , enUSA

SYNC™
Note: SYNC Services requires activation
before use. Visit www.SYNCMyRide.com to
register and check your eligibility for
complimentary services. Standard phone
and message rates may apply. Subscription
may be required. You must also have the
active SYNC Services Bluetooth-enabled
cellular phone paired and connected to the
system in order to connect to, and use,
SYNC Services. See Using SYNC™ With
Your Phone (page 327).

Note: When you connect, the service uses
GPS technology and advanced vehicle
sensors to collect your vehicle's current
location, travel direction and speed to help
provide you with the directions, traffic
reports, or business searches you request.
Further, to provide the services you request,
for continuous improvement, the service
may collect and record call details and voice
communications. For more information, see
SYNC Services Terms and Conditions at
www.SYNCMyRide.com. If you do not want
Ford or its service providers to collect your
vehicle travel information or other
information identified in the Terms and
Conditions, do not subscribe or use the
service.

Note: This feature does not function
properly if you have enabled caller ID
blocking on your cellular phone. Make sure
your cellular phone is not blocking caller ID
before using SYNC Services.
Note: The driver is ultimately responsible
for the safe operation of the vehicle, and
therefore, must evaluate whether it is safe
to follow the suggested directions. Any
navigation features provided are only an aid.
Make your driving decisions based on your
observations of local conditions and existing
traffic regulations. Do not follow the route
suggestions if doing so would result in an
unsafe or illegal maneuver, place you in an
unsafe situation, or if you would be directed
into an area that you consider unsafe. Maps
used by this system may be inaccurate
because of errors, changes in roads, traffic
conditions or driving conditions.

SYNC Services uses advanced vehicle
sensors, integrated GPS technology and
comprehensive map and traffic data, to
give you personalized traffic reports,
precise turn-by-turn directions, business
search, news, sports, weather and more.
For a complete list of services, or to learn
more, please visit www.SYNCMyRide.com.
Connecting to SYNC Services Using
Voice Commands
1. Press the voice button.
2. When prompted, say "Services". This
initiates an outgoing call to SYNC
Services using your paired and
connected Bluetooth-enabled cellular
phone.
3. Once you connect to the service, follow
the voice prompts to request the
desired service, such as Traffic or
Directions. You can also say, "What are
my choices?" to receive a list of
available services from which to
choose.
4. Say, "Services" to return to the Services
main menu or for help, say, "Help".

342

F150 (TF6) , enUSA

SYNC™
Connecting to SYNC Services Using
the Phone Menu
1.
2.
3.

4.
5.

assist you by searching for businesses
by name or by category, residential
addresses by street address or by
name or specific street intersections.
Operator Assist is a feature of your
SYNC Services subscription. For more
information on Operator Assist, visit
www.SYNCMyRide.com/support.
2. Follow the voice prompts to select your
destination. Once you select your
destination, the system uploads your
current vehicle location, calculates a
route based on current traffic
conditions and sends it back to your
vehicle. After the route download is
complete, the phone call automatically
ends. You then receive audible and
visual driving instructions as you travel
toward your destination.
3. While on an active route, you can select
or say "Route summary" or "Route
status" to view the Route Summary
turn list or the Route Status ETA. You
can also turn voice guidance on or off,
cancel the route or update the route.

Press the phone button to enter the
phone menu.
Scroll to Services.
Press OK to confirm and enter the
Services menu. The display indicates
the system is connecting.
Press OK. SYNC initiates the call to the
Services portal.
Once you connect to the service, follow
the voice prompts to request the
desired service, such as Traffic or
Directions. You can also say, "What are
my choices?" to receive a list of
available services from which to
choose.
Say, "Services" to return to the Services
main menu or for help, say, "Help".

Receiving Turn-by-Turn Directions
1.

When connected to SYNC Services,
say "Directions" or "Business search".
To find the closest business or type of
business to your current location, just
say "Business search" and then
"Search near me". If you need further
assistance in finding a location you can
say "Operator" at any time within a
Directions or Business search to speak
with a live operator. The system may
prompt you to speak with an operator
when it has difficulty matching your
voice request. The live operator can

If you miss a turn, SYNC automatically asks
if you want the route updated. Just say,
"Yes" when prompted and the system
sends a new route to your vehicle.
Disconnecting from SYNC Services
1.

Press and hold the phone button on
the steering wheel.
2. Say "Goodbye" from the SYNC
Services main menu.

343

F150 (TF6) , enUSA

SYNC™

SYNC Services quick tips

Personalizing

You can personalize your Services feature to provide
quicker access to your most used or favorite information.
You can save address points such as work or home. You
can also save favorite information like sports teams or a
news category. You can learn more about personalization
by logging onto www.SYNCMyRide.com.

Push to interrupt

Press the voice button at any time (while connected to
SYNC Services) to interrupt a voice prompt or an audio
clip (such as a sports report) and say your voice command.

Portable

Your subscription is associated with your Bluetoothenabled cellular phone number, not your VIN (Vehicle
Identification Number). You can pair and connect your
phone to any vehicle equipped with SYNC Services and
continue enjoying your personalized services.
You can even access your account outside your vehicle.
Just use the number on your phone's call history. Traffic
and Directions features do not function properly but
information services and the 411 connect and text message
features are available.
To Access Using the Phone Menu

SYNC AppLink

Note: This feature is only available in the
United States.

Note: You must pair and connect your
smartphone to SYNC to access AppLink.

Note: iPhone users need to connect the
phone to the USB port in order to start the
application. We recommend you lock your
iPhone after starting an application.

Note: The AppLink feature is not available
if your vehicle is equipped with the MyFord
Touch or MyLincoln Touch system.

5.
6.

Note: Depending on your display type, you
can access AppLink from the media menu,
the phone menu, or by using voice
commands. Once an app is running through
AppLink, you can control main features of
the app through voice commands and
steering wheel controls.

344

F150 (TF6) , enUSA

Press the phone button to access the
SYNC phone menu on-screen.
Scroll to Mobile Apps and press OK to
access a list of available applications.
Scroll through the list of available
applications and press OK to select a
particular app.
Once an app is running through SYNC,
you can access an app’s menu by
pressing the MENU button to first
access the SYNC menu.
Select "SYNC-Media" by pressing OK.
Scroll until " Menu" is
displayed (such as, Pandora Menu),
then press OK. From here, you can
access an application's features, such
as Thumbs up and Thumbs down. For
more information, please visit
www.SYNCMyRide.com.

SYNC™
To Access Using the Media Menu
1.
2.
3.
4.
5.

7.
8.

USING SYNC™ WITH YOUR
MEDIA PLAYER

Press the AUX button on the center
console.
Press MENU to access the SYNC
menu.
Select "SYNC-Media" by pressing OK.
Scroll to Mobile Apps and press OK to
access a list of available applications.
Scroll through the list of available
applications and press OK to select a
particular app.
Once an app is running through SYNC,
you can access an app’s menu by
pressing the MENU button to first
access the SYNC menu.
Select "SYNC-Media" by pressing OK.
Scroll until " Menu" is
displayed (such as, Pandora Menu),
then press OK. From here, you can
access an application's features, such
as Thumbs up and Thumbs down. For
more information, please visit
www.SYNCMyRide.com.

You can access and play music from your
digital music player over your vehicle's
speaker system using the system's media
menu or voice commands. You can also
sort and play your music by specific
categories, such as artist and album.
Note: The system is capable of indexing up
to 30,000 songs.
SYNC is capable of hosting nearly any
digital media player including: iPod®,
Zune™, Plays from device players, and
most USB drives. SYNC also supports
audio formats, such as MP3, WMA, WAV
and ACC.

Connecting Your Digital Media
Player to the USB Port
Note: If your digital media player has a
power switch, make sure you switch it on
before plugging it in.
To Connect Using Voice Commands

To Access Using Voice Commands

1. Plug the device into the USB port.
2. Press the voice icon and when
prompted, say "USB".
3. You can now play music by saying any
of the appropriate voice commands.
See the media voice commands.

1. Press the voice icon.
2. When prompted, say "Mobile Apps".
3. Say the name of the application after
the tone.
4. The app should start. While an app is
running through SYNC, you can press
the voice button and speak commands
specific to the app, such as "Play
Station Quickmix". Say "Help" to
discover available voice commands.

To Connect Using the System Menu
1. Plug the device into the USB port.
2. Press AUX and then MENU to enter
the media menu.
3. Scroll to Select Source. Press OK.
4. Scroll to USB. Press OK.
5. Depending on how many digital media
files are on your connected device,
Indexing may appear in the radio
display. When indexing is complete, the
screen returns to the Play menu.
345

F150 (TF6) , enUSA

SYNC™
Press OK and scroll through selections of:
• Play All
• Albums
• Genres
• Playlists
• Tracks
• Explore USB
• Similar Music
• Return

"USB"

"Play playlist "

"Play previous folder"
"Play previous track"

1,2

"Play song "

"Play track "

What's Playing?

1,2

"Refine album "

At any time when a track is playing, you
can press the voice icon and ask the
system "What's playing?". The system
reads the metadata tags (if populated) of
the playing track to you.

"Refine artist "
"Refine song "

1,2

"Repeat off"

Press the voice icon. When
prompted, say "USB", then any
of the following:

"Repeat on"
"Search album "
"Search artist "

"Autoplay off"

"Search genre "

"Autoplay on"

"Search song "

"Search track "
"Shuffle off"

"Play"

"Shuffle on"
1,2

"Play album "
"Play all"

1,2

"Play artist "

"Play genre "

1,2

"Play next track"

346

F150 (TF6) , enUSA

1,2

"Connections"
"Pause"

1,2

"USB"

"Play next folder"

1,2

"Refine track "

Media Voice Commands

E142599

1,2

SYNC™
1

is a dynamic listing, meaning that
it could be the name of anything, such as
a group, artist or song.

"USB"

"Similar music"

This voice command is not available until
indexing is complete.

"What's playing?"

This voice command is only available in
folder mode.
Voice command guide

"Autoplay"

Turn autoplay on to listen to music processed during
indexing. Turn autoplay off to allow the indexing process
to finish before the system plays any of your music.

"Search genre" or "Play
genre"

The system searches all the data from your indexed music
and, if available, begins to play the chosen type of music.
You can only play genres of music that are present in the
GENRE metadata tags that you have on your digital media
player.

"Similar music"

The system compiles a playlist and then plays music
similar to what is currently playing from the USB port using
indexed metadata information.

"Search" or "Play" artist,
track or album

The system searches for specific artist, track or album
information from the music indexed through the USB port.

"Refine"

This allows you to make your previous command more
specific. For example, if you asked to search and play all
music by a certain artist, you could then say, "Refine
album" and choose a specific album from the list to view.
If you then select Play, the system only plays music from
that specific album.

Indexing times can vary from device to device and with regard to the number of songs
the system needs to process.
Press the voice icon. When prompted, say,
"Bluetooth audio", then any of the
following:

"BLUETOOTH AUDIO"

"Connections"
"Pause"
"Play"
"Play next track"
"Play previous track"

347

F150 (TF6) , enUSA

SYNC™
Media Menu Features

and also to add, connect or delete devices.

The media menu allows you to select your
media source, how to play your music
(such as by artist, genre, shuffle or repeat),

Press AUX and then MENU to enter
the media menu.
2. Scroll to cycle through:

When you select:

You can:

Play Menu

Play your music by artist, album, genre, playlist, track,
similar music or play all music. You can also choose to
Explore USB to view the supported digital music files on
your playing device.

Select Source

Select and play music from your USB port, auxiliary input
jack (line in) or stream music from your Bluetooth-enabled
phone.
SYNC USB: Press OK to access music plugged into your
USB port. You can also plug in devices to charge them (if
supported by your device). Once connected, the system
indexes any readable media files.

Bluetooth Audio: This is a phone-dependent feature that
allows you to stream music playing on your Bluetoothenabled phone. If supported by your device, you can press
SEEK to play the previous or next track.
SYNC Line In: Press OK to select and play music from your
2

portable music player over your vehicle's speakers.
Media Settings

Choose to shuffle or repeat your music and select your
Autoplay settings. Once you turn these selections on, they
remain on until you turn them off. Press SEEK to play the
3

previous or next track.

Shuffle: Press OK to shuffle available media files in the
current playlist. To shuffle all media tracks, you must select
Play All in the play menu and then select Shuffle.
Repeat: Press OK to repeat any song.
Autoplay: Turn autoplay on to listen to music processed
during indexing. Turn autoplay off to allow the indexing
process to finish before the system plays any of your
4

music.
Mobile Apps

Interact with SYNC-capable mobile applications on your
smartphone.

348

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

System Settings

Access Bluetooth Device menu listings (Add, Connect, Set
as Primary, On and Off, Delete) as well as Advanced menu
listings (prompts, languages, defaults, master reset, install
application and system information).

Exit Media Menu

Press OK to exit the media menu.

The time required to complete this depends on the size of the media the system needs
to index. If autoplay is on, you can listen to media processed during indexing. If autoplay
is off, you cannot listen to music until the system finishes indexing media. SYNC is capable
of indexing thousands of average size media and notifies you if it reaches the maximum
indexing file size.
2

If you have already connected a device to the USB port, you cannot access the line in
feature. Some digital media players require both USB and line in ports to stream data
and music separately.
3

Some digital media players require both USB and line in ports to stream data and music
separately
4

Indexing times can vary from device to device and with regard to the number of songs
the system needs to process.
Press AUX and then MENU to enter
the media menu.
2. Scroll to Play. Press OK.
1.

Accessing Your Play Menu
This menu allows you to select and play
your media by artist, album, genre, playlist,
track, similar music or even to explore what
is on your USB device.

If there are no media files to access, the
display indicates there is no media. If there
are media files, you have the following
options:

Note: If your digital media player has a
power switch, make sure you switch it on
before plugging it in.
When you select:

You can:

Play All

Play all indexed media (tracks) from your playing device
in flat file mode, one at a time in numerical order.
Press OK to select. The first track title appears in the
display.

Artists

Sort all indexed media by artist. Once selected, the system
lists and then play all artists and tracks alphabetically. If
there are fewer than 255 indexed artists, the system lists
them alphabetically in flat file mode. If there are more
than 255, the system categorizes them alphabetically.

349

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

1. Press OK to select. You can select to play All Artists or
any indexed artist.
2. Scroll to choose the desired artist. Press OK.
Albums

Sort all indexed media by albums. If there are fewer than
255 indexed albums, the system lists them alphabetically
in flat file mode. If there are more than 255, the system
categorizes them alphabetically.
1. Press OK to enter the album menu and select from
playing all albums or from any individual indexed album.
2. Scroll to choose the desired album. Press OK.

Genres

Sort indexed music by genre (category) type. SYNC lists
the genres alphabetically in flat file mode. If there are more
than 255, the system categorizes them alphabetically.
1. Press OK to select.
2. Scroll to select the desired genre. Press OK.

Playlists

Access your playlists (from formats, such as .ASX, .M3U,
.WPL or .MTP). The system lists your playlists alphabetically in flat-file mode. If there are more than 255, the system
categorizes them alphabetically.
1. Press OK to select.
2. Scroll to select the desired playlist. Press OK.

Tracks

Search for and play a specific indexed track. SYNC lists
your tracks alphabetically in flat file mode. If there are
more than 255, the system categorizes them alphabetically.
1. Press OK to select.
2. Scroll to select the desired track. Press OK.

Explore USB

Explore all supported digital media on your media device
connected to the USB port. You can only view media
content which is compatible with SYNC; other files saved
are not visible.
1. Press OK to select.
2. Scroll to explore indexed media on your flash drive.
*

Similar Music

Play music similar to what is currently playing from the
USB port. The system uses the metadata information of
each song to compile a playlist for you.

350

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

Press OK to select. The system creates a new list of similar
songs and begins playing. This feature does not include
tracks with incomplete metadata information.
Return

Exit the current menu.

With certain playing devices, if your metadata tags are not populated, the tracks are not
available in voice recognition, play menu or similar music. However, if you place these
tracks onto your playing device in "Mass Storage Device Mode", they are available in voice
recognition, play menu browsing and similar music. The system places Unknown items
into any unpopulated metadata tag.
1.

Press AUX and then MENU to enter
the media menu.
2. Scroll to System Settings. Press OK.
3. Scroll to Bluetooth Devices. Press OK.

System Settings
Bluetooth Devices
The Bluetooth Devices menu allows you
to add, connect and delete a device as turn
the Bluetooth feature on and off.
When you select:

You can:

Add Bluetooth Device

Pair more devices to the system.
1. Press OK to select and press OK again when Find SYNC
appears in the display.
2. Follow the directions in your phone's manual to put your
phone into discovery mode. A six-digit PIN appears in the
display.
3. When prompted on your phone's six-digit display, enter
the PIN.

Connect Bluetooth Device

Connect a previously paired Bluetooth-enabled device.
1. Press OK to select and view a list of previously paired
devices.
2. Scroll until you find the desired device, and then press
OK to connect the device.

Set Bluetooth

Turn the Bluetooth feature on and off.
1. Press OK and scroll to toggle between On and Off.
2. Make a selection, and then press OK.

Delete Device

Delete a paired media device.
1. Press OK and scroll to select the device.
2. Press OK to confirm.

Delete All Devices

Delete all previously paired devices.

351

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

Press OK to select.
Return
*

Exit the current menu.

This is a speed-dependent feature.

Setting Bluetooth to off disconnects all Bluetooth devices and turns off all Bluetooth
features.
1.

Press AUX and then MENU to enter
the media menu.
2. Scroll to System Settings. Press OK.
3. Scroll to Advanced. Press OK.

Advanced
The Advanced menu allows you to access
and set prompts, languages, defaults and
perform a master reset.
When you select:

You can:

Prompts

Have SYNC guide you by asking questions, helpful hints
or ask you for a specific action.
1. Press OK to select and scroll to select between on or
off.
2. Press OK when the desired selection appears in the
display. SYNC takes you back to the Advanced menu.

Languages

Choose from English, Français or Español. The displays
and prompts are in the selected language.
1. Press OK to select and then scroll through the languages.
2. Press OK when the desired selection appears in the
display.
3. If you change the language setting, the display indicates
that the system is updating. When complete, SYNC takes
you back to the Advanced menu.

Factory Defaults

Return to the factory default settings. This selection does
not erase your indexed information (phonebook, call
history, text messages and paired devices).
1. Press OK to select.
2. Press OK again when Restore Defaults? appears in
the display.
3. Press OK to confirm.

352

F150 (TF6) , enUSA

SYNC™
When you select:

You can:

Master Reset

Completely erase all information stored on SYNC (all
phonebook, call history, text messages and all paired
devices) and return to the factory default settings.

Application

Download new software applications (if available) and
then load the desired applications through your USB port.
See the web site for more information.

Return

Exit the current menu.
Use the website at any time to check your
phone's compatibility, register your
account and set preferences as well as
access a customer representative via an
online chat (during certain hours). Visit
www.SYNCMyRide.com,
www.SYNCMyRide.ca or
www.syncmaroute.ca for more
information.

SYNC™ TROUBLESHOOTING
Your SYNC system is easy to use. However,
should questions arise, see the tables
below.

Phone issues
Issue

Possible cause(s)

Possible solution(s)

The audio control settings
There is excessive background noise during a phone on your phone may be
affecting SYNC performcall.
ance.

Review your phone's manual
about audio adjustments.

During a call, I can hear the
other person but they
cannot hear me.

This may be a possible
phone malfunction.

Try turning off the device,
resetting the device,
removing the device's
battery, then trying again.

SYNC is not able to download my phonebook.

This is a phone-dependent
feature.
This may be a possible
phone malfunction.

Go to the website to review
your phone's compatibility.
Try turning off the device,
resetting the device or
removing the device's
battery, then trying again.
Try pushing your phonebook
contacts to SYNC by using
the Add Contacts feature.
Use the SYNCmyphone
feature available on the
website.

353

F150 (TF6) , enUSA

SYNC™
Phone issues
Issue

Possible cause(s)

Possible solution(s)

The system says Phonebook This may be a limitation on
Downloaded but the
your phone's capability.
phonebook in SYNC is
empty or missing contacts.

Try pushing your phonebook
contacts to SYNC by using
the Add Contacts feature.
If the missing contacts are
stored on your SIM card, try
moving them to the device
memory.
Remove any pictures or
special ring tones associated with the missing
contact.
Depending upon your phone,
you may have to grant SYNC
permission to access your
phonebook contacts. Make
sure to confirm when
prompted by your phone
during the phonebook
download.

I am having trouble
connecting my phone to
SYNC.

This is a phone-dependent
feature.
This may be a possible
phone malfunction.

Go to the website to review
your phone's compatibility.
Try turning off the device,
resetting the device or
removing the device's
battery, then trying again.
Try deleting your device
from SYNC, deleting SYNC
from your device and trying
again.
Check the security and auto
accept and prompt always
settings relative to the SYNC
Bluetooth connection on
your phone.
Update your device's firmware.
Turn off the Auto phonebook download setting.

Text messaging is not
working on SYNC.

This is a phone-dependent
feature.

Go to the website to review
your phone's compatibility.

354

F150 (TF6) , enUSA

SYNC™
Phone issues
Issue

Possible cause(s)

This may be a possible
phone malfunction.

Possible solution(s)

Try turning off the device,
resetting the device or
removing the device's
battery, then trying again.

USB and media issues
Issue

I am having trouble
connecting my device.

Possible cause(s)

This may be a possible
device malfunction.

SYNC does not recognize
This is a device limitation.
my device when I turn on the
car.

Possible solution(s)

Try turning off the device,
resetting the device,
removing the device's
battery, then trying again.
Make sure you are using the
manufacturer's cable.
Make sure you insert the
USB cable correctly into the
device and the USB port.
Make sure that the device
does not have an autoinstall program or active
security settings.
Make sure you are not
leaving the device in your
vehicle during very hot or
cold temperatures.

Bluetooth audio does not
stream.

This is a phone-dependent Review the device compatibility chart on the SYNC
feature.
The device is not connected. website to confirm your
phone supports the
Bluetooth audio streaming
function.
Make sure you correctly
connect the device to SYNC,
and that you have pressed
play on your device.

SYNC does not recognize
music that is on my device.

Your music files may not
contain the correct artist,
song title, album or genre
information.

355

F150 (TF6) , enUSA

Make sure that all song
details are populated.

SYNC™
USB and media issues
Issue

Possible cause(s)

Possible solution(s)

The file may be corrupted.
The song may have copyright protection, which does
not allow it to play.

Some devices require you to
change the USB settings
from mass storage to MTP
class.

Vehicle Health Report and Services (Traffic, Directions and Information) issues
Issue

Possible cause(s)

Possible solution(s)

I received a text that I did
not activate Vehicle Health
Report.

You did not activate your
account on the website.
You may have the wrong
VIN (vehicle identification
number) listed.

This is a free feature, but you
must first register online to
use it.
Make sure that your VIN is
correctly listed in your
account.

I am unable to retrieve the
report on the website, or I
receive a system error.

The preferred dealer
information did not load
correctly.

When you register your
account, you must choose a
preferred dealer. If it already
lists a dealer, try selecting
another dealer and logging
out. Log back in, change it
back to your preferred
dealer, and retrieve the
report.

I am unable to submit a
report.

This could be due to your
phone's compatibility.
Bad signal strength.
You did not register your
phone correctly on the
website.

Update your cellular number
in your account on the
website.
Make sure you have full
signal strength and that your
Bluetooth volume level has
been turned up.
Make sure the currently
connected phone is
registered on your
SYNCMyRide account.
Try deleting your phone and
performing a clean pairing.

I heard a commercial when
I tried to use Traffic, Directions and Information.

You did not activate this
phone for this service.
Your phone has ID blocker
active.

This is a free feature, but you
must first register online to
use it.

356

F150 (TF6) , enUSA

SYNC™
Vehicle Health Report and Services (Traffic, Directions and Information) issues
Issue

Possible cause(s)

Possible solution(s)

Turn off ID blocker on your
phone as the system recognizes you by your phone
number.
Make sure the currently
connected phone is the
same one that is registered
on your SYNCMyRide
account.

Voice command issues
Issue

Possible cause(s)

Possible solution(s)

SYNC does not understand You may be using the wrong
voice commands.
what I am saying.
You may be speaking too
soon or at the wrong time.

Review the phone voice
commands and the media
voice commands at the
beginning of their respective
sections.
After pressing the voice icon,
wait until after the tone
sounds and Listening
appears before saying a
command. Any command
spoken before this does not
register with the system.

SYNC does not understand You may be using the wrong
the name of a song or artist. voice commands.
You may be saying the
name differently than the
way you saved it.
The system may not be
reading the name the same
way you are saying it.

Review the media voice
commands at the beginning
of the media section.
Say the song or artist
exactly as listed. If you say
"Play Artist Prince", the
system does not play music
by Prince and the Revolution
or Prince and the New
Power Generation.
Make sure you are saying the
complete title, such as
"California remix featuring
Jennifer Nettles".

357

F150 (TF6) , enUSA

SYNC™
Voice command issues
Issue

Possible cause(s)

Possible solution(s)

If the song titles are in all
CAPS, you have to spell
them. LOLA requires you to
say "L-O-L-A".
Do not use special characters in the title. The system
does not recognize them.
SYNC does not understand
or is calling the wrong
contact when I want to
make a call.

You may be using the wrong
voice commands.
You may be saying the
name differently than the
way you saved it.
The system may not be
reading the name the same
way you are saying it.
Contacts in your phonebook
may be very short and
similar, or they may contain
special characters.
Your phonebook contacts
may be in CAPS.

358

F150 (TF6) , enUSA

Review the Phone voice
commands at the beginning
of the phone section.
Make sure you are saying the
contacts exactly as they are
listed. For example, if you
save a contact as Joe
Wilson, say "Call Joe
Wilson".
Using the SYNC phone
menu, open the phonebook
and scroll to the name
SYNC is having trouble
understanding. SYNC will
read the name to you, giving
you some idea of the
pronunciation SYNC is
expecting.
The system works better if
you list full names, such as
"Joe Wilson" rather than
"Joe".
Do not use special characters, such as 123 or ICE, as
the system does not recognize them.
If a contact is in CAPS, you
have to spell it. JAKE
requires you to say "Call JA-K-E".

MyFord Touch™ (If Equipped)
GENERAL INFORMATION

E161891

Phone

Navigation (or Information if your vehicle is not equipped with Navigation)

Climate (or Settings, if your vehicle is equipped with manual climate control)

Settings (if your vehicle is equipped with automatic climate control)

Home

Information

Entertainment

359

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
This system uses a four-corner strategy to
provide quick access to several vehicle
features and settings. The touchscreen
provides easy interaction with your cellular
phone, multimedia, climate control and
navigation system. The corners display any
active modes within those menus, such as
phone status or the climate temperature.

Press to select any of the following:
• Driver Settings
• Recirculated Air
• Auto
• Dual
• Passenger Settings
• A/C
• Defrost

Note: Some features are not available while
your vehicle is moving.

SETTINGS

Note: Your system is equipped with a
feature that allows you to access and
control audio features for 30 minutes after
you switch the ignition off (and no doors
open).

E142607

Press to select any of the following:
• Clock
• Display
• Sound
• Vehicle
• Settings
• Help

PHONE
Press to select any of the following:
• Phone
• Quick Dial
• Phonebook
• History
• Messaging
• Settings

HOME
Press to access your home
screen. Depending on your
vehicle’s option package and software,
your screens may vary in appearance from
the descriptions in this section. Your
features may also be limited depending on
your market. Check with an authorized
dealer for availability.
E142613

NAVIGATION
Press to select any of the following:
• My Home
• Favorites
• Previous Destinations
• Point of Interest
• Emergency
• Street Address
• Intersection
• City Center
• Map
• Edit Route
• Cancel Route

INFORMATION
E142608

Press to select any of the following:
• Services
• Travel Link
• Alerts
• Calendar
• Apps

CLIMATE

ENTERTAINMENT

360

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Using Your Bezel Controls

Press to select any of the following:
• AM
• FM
• SIRIUS
• CD
• USB
• BT Stereo
• SD Card
• A/V In

Depending on your vehicle and option
package, you may also have these controls
on your bezel:
• Power: Switch the media or climate
features off and on.
• VOL: Control the volume of playing
media.
• Temperature, fan and climate control
buttons: Control the temperature, fan
speed or settings of the climate control
system.
• Seek and Tune buttons: Use as you
normally would in media modes.
• Eject: Eject a CD from the
entertainment system.
• SOURCE: Touch the word repeatedly
to see all available media modes. The
screen does not change, but you see
the media change in the lower left
status bar.
• MEDIA: Touch the word to access the
Sound menu where you can adjust
settings such as: Bass, Treble,
Midrange, Balance and Fade, DSP
(Digital Signal Processing), Occupancy
Mode and Speed Compensated
Volume. (Your vehicle may not have
all of these sound options.)
• Hazard flasher: Switch the hazard
flashers off and on.

Using the Touch-Sensitive
Controls on Your System
To turn a feature on and off, just touch the
graphic with your finger. To get the best
performance from the touch-sensitive
controls:
• Do not press hard on the controls. They
are sensitive to light touch.
• Use your bare finger to touch the center
of a touch-control graphic. Touching
off-center of the graphic may affect
operation of a nearby control.
• Make sure your hands are clean and
dry.
• Since the touchscreen operates based
on the touch of a finger, you may have
trouble using it if you are wearing
gloves.
• Keep metal and other conductive
material away from the surface of the
touchscreen as this may cause
electronic interference (for example,
inadvertently turning on a feature other
than the one you meant to turn on).

Using Your Steering Wheel
Controls
Depending on your vehicle and option
package, you can use your steering wheel
controls to interact with the touchscreen
system. See Steering Wheel (page 65).

Cleaning the Touchscreen Display
Use a clean, soft cloth such as one used
for cleaning glasses. If dirt or fingerprints
are still visible, apply a small amount of
alcohol to the cloth. Do not pour or spray
alcohol onto the display. Do not use
detergent or any type of solvent to clean
the display.

Support
The SYNC support team is available to
help you with any questions you are not
able to answer on your own.

361

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Monday-Saturday, 8:30am-9:00pm EST.

•

Sunday, 10:30am-7:30pm EST.
In the United States, call: 1-800-392-3673.
In Canada, call: 1-800-565-3673.
•

Times are subject to change due to
holidays.

Safety Information

Make sure that you review your device's
manual before using it with SYNC.

Do not leave playing devices in your
vehicle during extreme conditions as it
could cause them damage. See your
device's user guide for further
information.
For your safety, some SYNC functions
are speed-dependent. Their use is
limited to when your vehicle is traveling
at speeds under 3 mph (5 km/h).

Speed-restricted Features
Some features of this system may be too
difficult to use while your vehicle is moving
so they are restricted from use unless your
vehicle is stationary.
• Screens crowded with information,
such as Point of Interest reviews and
ratings, SIRIUS Travel Link sports
scores, movie times or ski conditions.
• Any action that requires you to use a
keyboard is restricted, such as entering
a navigation destination or editing
information.
• All lists are limited so the user can view
fewer entries (such as phone contacts
or recent phone call entries).

Do not attempt to service or repair the
system. See an authorized dealer.
Do not operate playing devices if the
power cords or cables are broken, split
or damaged. Place cords and cables
out of the way, so they do not interfere
with the operation of pedals, seats,
compartments or safe driving abilities.

See the following chart for more specific
examples.

Restricted features

Cellular Phone

Pairing a Bluetooth phone
Adding phonebook contacts or uploading phonebook
contacts (from a USB)
List entries are limited for phone contacts and recent
phone call entries

System Functionality

Editing the keypad code
Enabling Valet Mode

362

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Restricted features

Editing settings while the rear view camera or active park
assist are active
Wi-Fi and Wireless

Editing wireless settings
Editing the list of wireless networks

Videos, Photos and Graphics Playing video
Editing the screen's wallpaper or adding new wallpaper
Text Messages

Composing text messages
Viewing received text messages
Editing preset text messages

Navigation

Using the keyboard to enter a destination
Demo navigation route
Adding or editing Address Book entries or Avoid Areas
The cellular profile, media device index,
and development log remain in your
vehicle unless you delete them and are
generally accessible only in your vehicle
when the cellular phone or media player
is connected. If you no longer plan to use
the system or your vehicle, we recommend
you perform a Master Reset to erase all
stored information.

Privacy Information
When you connect a cellular phone to
SYNC, the system creates a profile within
your vehicle that links to that cellular
phone. This profile helps in offering you
more cellular features and operating more
efficiently. Among other things, this profile
may contain data about your cellular
phone book, text messages (read and
unread), and call history, including history
of calls when your cell phone was not
connected to the system. In addition, if you
connect a media device, the system
creates and retains an index of supported
media content. The system also records a
short development log of approximately
10 minutes of all recent system activity.
The log profile and other system data may
be used to improve the system and help
diagnose any problems that may occur.

System data cannot be accessed without
special equipment and access to your
vehicle's SYNC module. Ford Motor
Company and Ford of Canada do not
access the system data for any purpose
other than as described absent consent, a
court order, or where required by law
enforcement, other government
authorities, or other third parties acting
with lawful authority. Other parties may
seek to access the information
independently of Ford Motor Company and
Ford of Canada. For further privacy
information, see the sections on 911 Assist,
Vehicle Health Report, and Traffic,
Directions and Information.

363

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Using Voice Recognition

What Can I Say?

This system helps you control many
features using voice commands. This
allows you to keep your hands on the
wheel and focus on what is in front of you.
The system provides feedback through
audible tones, prompts, questions and
spoken confirmations depending on the
situation and the chosen level of
interaction (voice settings).

To access the available voice commands
for the current session, do one of the
following:
• During a voice session, press the Help
icon (?) in the lower left status bar of
the screen.
• Say, "What can I say?" for an
on-screen listing of the possible voice
commands associated with your
current voice session.
• Press the voice icon. After the tone, say,
"Help" to hear a list of possible voice
commands.

The system also asks short questions
(confirmation prompts) when it is not sure
of your request or when there are multiple
possible responses to your request.
When using voice commands, words and
icons may appear in the lower left status
bar indicating the status of the voice
session (such as Listening, Success, Failed,
Paused or Try Again).

Helpful Hints
•

How to Use Voice Commands with Your
System

E142599

•

Press the voice icon. After the
tone, speak your command
clearly.

•

These commands can be said at any time
during a voice session

•

"Cancel"
"Exit"

Accessing a List of Available Commands

"Go back"

•

"List of commands"
"Main menu"

•

"Next page"
"Previous page"
"What can I say?"
"Help"

364

F150 (TF6) , enUSA

Make sure the interior of your vehicle is
as quiet as possible. Wind noise from
open windows and road vibrations may
prevent the system from correctly
recognizing spoken commands.
After pressing the voice icon, wait until
after the tone sounds and Listening
appears before saying a command. Any
command spoken prior to this does not
register with the system.
Speak naturally, without long pauses
between words.
At any time, you can interrupt the
system while it is speaking by pressing
the voice icon.

If you use the touchscreen, press the
Settings icon > Help > Voice
Command List.
If you use the steering wheel control,
press the voice icon. After the tone,
speak your command clearly.

MyFord Touch™ (If Equipped)
•
Available voice commands

"Audio list of commands"
"Bluetooth audio list of commands"

•

"Browse list of commands"
"CD list of commands"
"Climate control list of commands"
"List of commands"
"Navigation list of commands"

•

"Phone list of commands"
"Radio list of commands"
"SD card list of commands"
"Sirius satellite list of commands"
"Travel link list of commands"

Interaction Mode: Novice mode
provides detailed interaction and
guidance while the advanced mode
has less audible interaction and more
tone prompts.
Confirmation Prompts: The system
uses these short questions to confirm
your voice request. If turned off, the
system simply makes a best guess as
to what you requested. The system
may still occasionally ask you to
confirm settings.
Phone and Media Candidate Lists:
Candidate lists are lists of possible
results from your voice commands. The
system creates these lists when it has
the same confidence level of several
options based on your voice command.

To access these settings using the
touchscreen:

Press the Settings icon > Settings >
Voice Control.
2. Select from:
• Interaction Mode
• Confirmation Prompts
• Media Candidate Lists
• Phone Candidate Lists
• Voice Control Volume.

"USB list of commands"
"Voice instructions list of commands"
"Voice settings list of commands"
"Help"
*

This command is only available when
your vehicle is equipped with the
navigation system, and the navigation
system SD card is in the card slot.

To access these settings using voice
commands:
1.

Press the voice icon. Wait for the
prompt "Please say a command".
Another tone sounds to let you know
the system is listening.
2. Say any of the following commands:

This command is only available when
you have an active SIRIUS satellite radio
subscription.
Voice Settings

Voice settings using voice commands

Voice settings allow you to customize the
level of system interaction, help and
feedback. The system defaults to standard
interaction that uses candidate lists and
confirmation prompts as these provide the
highest level of guidance and feedback.

"Confirmation prompts off"
"Confirmation prompts on"
"Interaction mode advanced"

365

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Using Voice Commands with the
Touchscreen Options

Voice settings using voice commands

"Interaction mode novice"

Your voice system has a dual mode feature
which allows you to switch between using
voice commands and making on-screen
selections. This is available only when the
system displays a list of candidates
generated during a voice session. For
example, when entering in a street address
or trying to call a contact from the phone
you paired to the system.

"Media candidate lists off"
"Media candidate lists on"
"Phone candidate lists off"
"Phone candidate lists on"
"Help"

SETTINGS

A
B
C
D
E
F
E161968

Clock

Display

Sound

Vehicle

Settings

Help

366

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Under this menu, you can set
your clock, access and adjust the
display, sound and vehicle
settings as well as access settings for
specific modes or the help feature.

•

Clock

•

E142607

•

Note: You cannot manually set the date.
Your vehicle’s GPS does this for you.
Note: If the battery has been disconnected,
your vehicle needs to acquire a GPS signal
to update the clock. Once your vehicle
acquires the signal, it may take a few
minutes for the update to display the correct
time.
•
E142607

1. Press the Settings icon > Clock.
2. Press + and - to adjust the time.
From this screen, you can also make other
adjustments such as 12-hour or 24-hour
mode, activate GPS time synchronization
and have the system automatically update
new time zones.

•

You can also turn the outside air
temperature display off and on. It appears
at the top center of the touchscreen, next
to the time and date.

Uploading Photos for Your Home
Screen Wallpaper
Note: You cannot load photos directly from
your camera. You must access the photos
either from your USB mass storage device
or from an SD card.

The system automatically saves any
updates you make to the settings.

Display

Note: Photographs with extremely large
dimensions (such as 2048 x 1536) may not
be compatible and appear as a blank
(black) image on the display.

You can adjust the touchscreen display
through the touchscreen or by pressing the
voice button on your steering wheel
controls and when prompted, say, "Display
settings".

Your system allows you to upload and view
up to 32 photos.
To access, press the Settings
icon > Display > Edit
Wallpaper, and then follow the
system prompts to upload your
photographs.

Press the Settings icon >
Display, to access and make
E142607
adjustments using the
touchscreen.

E142607

367

F150 (TF6) , enUSA

Brightness allows you to make the
screen display brighter or dimmer.
Auto DIM, when set to On, lets you use
the Auto Dim Manual Offset feature.
When set to Off, screen brightness
does not change.
Mode allows you to set the screen to
a certain brightness or have the system
automatically change based on the
outside light level, or turn the display
off.
• If you select AUTO or NIGHT, you
have the options of turning the
display's Auto Dim feature on or off
and changing the Auto Dim Manual
Offset feature.
Auto Dim Manual Offset allows you
to adjust screen dimming as the
outside lighting conditions change from
day to night. This feature also allows
you to adjust screen brightness using
the instrument panel dimming control.
Edit Wallpaper
• You can have your touchscreen
display the default photo or upload
your own.

MyFord Touch™ (If Equipped)
Only the photograph(s), which meets the
following conditions, display:
• Compatible file formats are as follows:
.jpg, .gif, .png, .bmp
• Each file must be 1.5 MB or less.
• Recommended dimensions: 800 x 384

When done making your selections, press
Run Vehicle Health Report Now if you
want your report.
You can find more information on Vehicle
Health Report in this chapter. See
Information (page 399).
Rear View Camera

Sound

This menu allows you to access settings
for your rear view camera.

Press the Settings icon > Sound,
then select from the following:
E142607

E142607

Sound

settings:

Bass

•
•
•

Midrange
Treble

Rear Camera Delay
Visual Park Aid Alert
Guidelines.

You can find more information on the rear
view camera in another chapter. See Rear
View Camera (page 173).

Set Balance and Fade
DSP

Press the Settings icon >
Vehicle > Rear View Camera,
then select from the following

Enable Valet Mode

Occupancy Mode

Valet mode allows you to lock the system.
No information is accessible until the
system is unlocked with the correct PIN.
You can create your own four-digit PIN to
lock and unlock the system.

Speed Compensated Volume
*

Your vehicle may not have these sound
settings.

Vehicle

E142607

•
•
•

Press the Settings icon >
Vehicle, then select from the
following:

E142607

Press the Settings icon > Vehicle >
Enable Valet Mode.
2. When prompted, enter a four-digit PIN.

Vehicle Health Report
Rear View Camera
Enable Valet Mode.

After you press Continue, the system locks
until you enter the PIN again.
Note: If the system locks, and you need to
reset the PIN, enter 3681 and the system
unlocks.

Vehicle Health Report
Turn Automatic Reminders on and off
and set the mileage interval at which you
would like to receive the reports. Press ?
for more information on these selections.

368

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Settings

System

Access and adjust system settings, voice
features, as well as phone, navigation and
wireless settings.

E142607

Press the Settings icon >
Settings > System, then select
from the following:

System

Language

Select to have the touchscreen display in English, Spanish
or French.

Distance

Select to display units in kilometers or miles.

Temperature

Select to display units in Celsius or Fahrenheit.

System Prompt Volume

Adjust the volume of voice prompts from the system.

Touch Screen Button Beep

Select to have the system beep to confirm choices made
through the touchscreen.

Touch Panel Button Beep

Select to have the system beep to confirm button choices
made through the climate or audio system.

Keyboard Layout

Have the touchscreen keyboard display in QWERTY or
ABC format.

Install Applications

Install any downloaded applications or view the current
software licenses.

Master Reset

Select to restore factory defaults. This erases all personal
settings and personal data.

Voice Control

E142607

Press the Settings icon >
Settings > Voice Control, then
select from the following:

369

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)

Voice control

Interaction Mode

Standard interaction mode provides more detailed interaction and guidance. Advanced mode has less audible
interaction and more tone prompts.

Confirmation Prompts

Have the system ask you short questions if it has not
clearly heard or understood your request.

Media Candidate Lists

Candidate lists are possible results from your voice
commands. The system simply makes a best guess at
your request with these turned off.

Phone Candidate Lists

Candidate lists are possible results from your voice
commands. The system simply makes a best guess at
your request with these turned off.

Voice Control Volume

This allows you to adjust the system’s voice volume level.

Even with confirmation prompts turned off, the system may occasionally ask you to
confirm settings
Media Player

E142607

Press the Settings icon >
Settings > Media Player, then
select from the following:
Media player

Autoplay

When this feature is on, the system automatically switches
to the media source upon initial connection. This allows
you to listen to music during the indexing process. When
this feature is off, the system does not automatically
switch to the inserted media source.

Bluetooth Devices

Select to connect, disconnect, add or delete a device. You
can also set a device as your favorite so that the system
automatically attempts to connect to that device at every
ignition cycle.

Index Bluetooth Audio
Devices

When this feature is on, the system automatically indexes
media on your connected Bluetooth device.

370

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Media player

Gracenote Database Info

This allows you to view the version level of the Gracenote
Database.

Gracenote Mgmt

With this feature on, the Gracenote Database supplies
metadata information for your music files. This overrides
information from your device. This feature defaults to off.

Cover Art Priority

With this feature on, the Gracenote Database supplied
cover art for your music files. This overrides any art from
your device. This feature defaults to Media Player.

Navigation

E142607

Press the Settings icon >
Settings > Navigation, then
select from the following:
Navigation

Map Preferences

Turn breadcrumbs on and off.
Have the system display your turn list top to bottom or
bottom to top.
Turn the Parking POI notification on and off.

Route Preferences

Choose to have the system display the Shortest, Fastest
or most Ecological route first. If you set Always Use
Preferred Route to Yes, the system uses the selected
route type to calculate only one route to the desired
destination. Always Use Preferred Route bypasses route
selection in destination programming. The system only
calculates one route based on the preferred route setting.
Eco Time Penalty allows you to select a low, medium or
high cost for the calculated Eco Route. The higher the
setting, the longer the time allotment is for the route.
Have the system avoid freeways.
Have the system avoid tollroads.
Have the system avoid ferries or car trains.
Have the system use HOV (high-occupancy vehicle) lanes.

Navigation Preferences

Have the system use guidance prompts.

371

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Navigation

Have the system automatically fill-in State/Province
information.
Traffic Preferences

Have the system display areas where roadwork occurs.
Have the system display incident icons.
Have the system display areas where difficult driving
conditions may occur.
Have the system display areas where snow and ice on the
road may occur.
Have the system display any smog alerts.
Have the system display weather warnings.
Have the system display where there may be reduced
visibility.
Have the system turn on your radio for traffic announcements.

Avoid Areas

Enter specific areas that you would like to avoid on
planned navigation routes.

Phone

E142607

Press the Settings icon >
Settings > Phone, then select
from the following:
Phone

Bluetooth Devices

Connect, disconnect, add or delete a device, as well as
save it as a favorite.

Bluetooth

Turn Bluetooth on and off.

Do Not Disturb

Have all calls go directly to your voice mail and not ring
inside your vehicle. With this feature turned on, text
message notifications are also suppressed and do not ring
inside your vehicle.

911 Assist

Turn on or turn off the 911 Assist feature. See Information
(page 399).

372

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Phone

Phone Ringer

Select the type of notification for phone calls - ring tone,
beep, text to speech, or have it be silent.

Text Message Notification

Select the type of notification for text messages - alert
tone, beep, text to speech, or have it be silent.

Internet Data Connection

If compatible with your phone, you can adjust your internet
data connection. Select to make your connection profile
with the personal area network or to turn off your
connection. You can also choose to adjust your settings
or have the system always connect, never connect when
roaming or query on connect. Press ? for more information.

Manage Phonebook

Access features, such as automatic phonebook download,
re-download your phonebook, add contacts from your
phone as well as delete or upload your phonebook.

Roaming Warning

Have the system alert you when in Roaming mode.
feature, everyone in your vehicle can also
gain access the internet if you have a USB
mobile broadband connection inside your
vehicle, your phone supports personal area
networking and if you park outside a
wireless hotspot.

Wireless & Internet
Your system has a Wi-Fi feature that
creates a wireless network within your
vehicle, thereby allowing other devices
(such as personal computers or phones)
in your vehicle to speak to each other,
share files or play games. Using this Wi-Fi

E142607

following:

373

F150 (TF6) , enUSA

Press the Settings icon >
Settings > Wireless &
Internet, then select from the

MyFord Touch™ (If Equipped)

Wi-fi

Wi-Fi Settings

Wi-Fi Network (Client) Mode turns the Wi-Fi feature on
and off in your vehicle. Make sure you turn it on for
connectivity purposes.
Choose a Wireless Network allows you to use a previously stored wireless network. You can categorize by
alphabetical listing, priority and signal strength. You can
also choose to search for a network, connect to a network,
disconnect from a network, receive more information,
prioritize a network or delete a network.
Gateway (Access Point) Mode makes SYNC an access
point for a phone or a computer when turned on. This
forms the local area network within your vehicle for things,
such as game playing, file transfer and internet browsing.
Press ? for more information.
Gateway (Access Point) Settings allows you to view
and change settings for using SYNC as the internet
gateway.
Gateway (Access Point) Device List allows you to view
recent connections to your Wi-Fi system.

USB Mobile Broadband

Instead of using Wi-Fi, your system can also use a USB
mobile broadband connection to access the internet. (You
must turn on your mobile broadband device on your
personal computer before connecting it to the system.)
This screen allows you to set up what is your typical area
for your USB mobile broadband connection. (USB mobile
broadband settings may not display if the device is already
on.) You can select the following: Country, Carrier, Phone
Number, User Name and Password.

Bluetooth Settings

Shows you the currently paired devices as well as giving
you your typical Bluetooth options to connect, disconnect,
set as favorite, delete and add device. Bluetooth is a
registered trademark of the Bluetooth SIG.

Prioritize Connection
Methods

Choose your connection methods and change them as
needed. You can select to Change Order and have the
system either always attempt to connect using a USB
mobile broadband or using Wi-Fi.

374

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
The
Wi-Fi

CERTIFIED Logo is a certification mark of
the Wi-Fi Alliance.
Help
Press the Settings icon > Help,
then select from the following:
E142607

E142626

Help

Where Am I?

View your vehicle's current location, if your vehicle is
equipped with navigation. If your vehicle is not equipped
with navigation, you do not see this button.

System Information

Touchscreen system serial number
Your vehicle identification number (VIN)
Touchscreen system software version
Navigation system version
Map database version
Sirius satellite radio ESN
Gracenote Database Information and Library version

Software Licenses

View the licenses for any software and applications
installed on your system.

Driving Restrictions

Certain features are not accessible when your vehicle is
moving.

911 Assist

Turn on and turn off the 911 Assist feature. See Information (page 399).
In Case of Emergency (ICE) Quick Dial: allows you to
save up to two numbers as ICE contacts for quick access
if there is an emergency. Select Edit to access your
phonebook and then select the desired contacts. The
numbers then appear as options on this screen for the ICE
1 and ICE 2 buttons. The ICE contacts you select appear
at the end of the 911 Assist call process.

Voice Command List

View categorized lists of voice commands.

375

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
To access Help using the voice commands,
press the voice button, then, after the tone,

say "Help". The system provides allowable
voice commands for the current mode.

ENTERTAINMENT

A
B

C
D
E

E161892

AM 1 and AM AST

FM 1, FM 2 and FM AST

SIRIUS

USB

Touch this button to scroll down for more options, such as SD Card, BT Stereo
and A/V In

These buttons change with the media mode you are in.

Radio memory presets and CD controls.

Note: Some features may not be available
in your area. Contact an authorized dealer
for more information.

Browsing Device Content
When listening to audio on a device, you
can browse through other devices without
having to change sources. For example, if
you are currently listening to audio on an
SD card, you can browse all the artists that
are stored on your USB device.

You can access these options using the
touchscreen or voice commands.

376

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Your voice system allows you to change
audio sources with a simple voice
command. For example, if you are listening
to music on a USB device, then want to
switch to a satellite radio channel, simply
press the voice button on the steering
wheel controls and say the name of the
SIRIUS station (such as, "the Highway").
The following voice commands are
available at the top level of the voice
session no matter which current audio
source you are listening to (such as a USB
device or SIRIUS satellite radio).

Press the voice icon on the
steering wheel. When prompted,
you can say:

E142599

"BROWSE" within devices

"Browse"

"Browse games"

"Browse channels"
"Browse SD card"

Note: This is only available when your
MyFord Touch system language is set to
North American English.

"Browse Sirius channel guide"
"Browse USB"

Sample commands

"Help"

"<87.9-107.9>"

If you only say, "Browse", you can then
say any commands in the following chart.

"<530-1710>"

This command is only usable if you have
an active subscription to SIRIUS satellite
radio.

""*

"BROWSE"

"FM <87.9-107.9>"

" Games"

"AM <530-1710>"

"Play [album] "**

"Play [artist] "**

" channels"

"Play [genre] "**

"SD card"

"Sirius Channel Guide"
"USB"

"Play [playlist] "**

"Play [song] "**

"Help"

"Play "

This command is only usable if you have
an active subscription to SIRIUS satellite
radio.

"Play by "

For more commands in SD card or USB
mode, see the "SD Card and USB Port"
section of this chapter.

377

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Options

Sample commands

Sound Settings

"Sirius <0-223>"*

Touch this button to adjust settings for:

"Sports games"*

•
•
•
•
•
•
•

This command is only usable if you have
an active subscription to SIRIUS satellite
radio.
**

The commands that have [ ] around the
word means that the word is optional. For
example, if you say, "Play Metallica", this
is the same as the voice command, "Play
[artist] ".

Note: Your vehicle may not have all these
sound settings.

AM/FM Radio

Set PTY for Seek/Scan

Touch the AM or FM tab to listen
to the radio.

This allows you to select a category of
music you would like to search for. You can
then choose to either seek or scan for the
stations playing that category.

E142611

To change between AM and FM presets,
just touch the AM or FM tab.

RDS Text Display

Memory Presets

This allows you to view the information
broadcast by FM stations.

Save a station by pressing and holding one
of the memory preset areas. There is a brief
mute while the radio saves the station.
Sound returns when finished.

AST
AST (Autostore) allows you to have the
system automatically store the six
strongest stations in your current location.

HD Radio
Touch this button to turn HD Radio on. The
light on the button illuminates when the
feature is on. HD Radio allows you to
receive radio broadcasts digitally, where
available, providing free, crystal-clear
sound. See HD Radio information later in
this chapter.

TAG Button
This feature is available when HD Radio is
on, and allows you to tag a song to
download later. When you select On, TAG
appears on-screen when HD Radio is
active. You can touch TAG to save the
information of the song that is playing.
When you plug in your portable music
player, the information transfers, if
supported by your device. When you are
connected to iTunes, the tags appear to
remind you of the songs you would like to
download. See HD Radio information later
in this chapter.

Scan
Touch this button to go to the next strong
AM or FM radio station. The light on the
button illuminates when the feature is on.

378

F150 (TF6) , enUSA

Bass
Midrange
Treble
Balance and Fade
DSP (Digital Signal processing)
Occupancy Mode
Speed Compensated Volume.

MyFord Touch™ (If Equipped)
The multicast indicator appears in FM
mode (only) if the current station is
broadcasting multiple digital broadcasts.
The highlighted numbers signify available
digital channels where new or different
content is available. HD1 signifies the main
programming status and is available in
analog and digital broadcasts. Other
multicast stations (HD2 through HD7) are
only available digitally.

Direct Tune
Touch this button to manually enter the
desired station number. Touch Enter when
you are done.
HD Radio™ Information (If Available)
Note: HD Radio broadcasts are not
available in all markets.
HD Radio technology is the digital
evolution of analog AM/FM radio. Your
system has a special receiver that allows
it to receive digital broadcasts (where
available) in addition to the analog
broadcasts, it already receives. Digital
broadcasts provide a better sound quality
than analog broadcasts with free,
crystal-clear audio and no static or
distortion. For more information, and a
guide to available stations and
programming, please visit
www.hdradio.com.

TAG allows you to save a song to
download later when you are on an
acquired HD Radio station and the feature
is on. To turn the feature on and use it:
1.

Press AM or FM > Options > TAG
Button > On.
2. When you hear a song you like, touch
TAG.
3. The system automatically saves the
song's information and transfers it to
your portable music player (if
supported) when you connect it to the
system. The system automatically
transfers the tag to your player (if
already connected) and a pop-up
confirms the transfer.
4. When you access iTunes with your
portable music player, the tags appear
to you as a reminder. The system
allows you to tag up to approximately
100 songs. For a list of devices that
support tagging, see
www.SYNCMyRide.com,
www.SYNCMyRide.ca or
www.syncmaroute.ca.

When HD Radio is on and you tune to a
station broadcasting HD Radio technology,
you may notice the following indicators on
your screen:

E142616

The HD Radio logo either blinks when
acquiring a digital station, and then stays
solid when digital audio is playing, or is grey
when acquiring a digital station, and then
changes to orange when digital audio is
playing. When this logo is available, you
may also see Title and Artist fields
on-screen.

379

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
When HD Radio broadcasts are active, you
can access the following functions:
• Scan allows you to hear a brief
sampling of all available stations. This
feature still works when HD Radio
reception is on, although it does not
scan for HD2-HD7 channels. You may
see the HD logo appear if the station
has a digital broadcast.

•

Memory presets allow you to save an
active channel as a memory preset.
Touch and hold a memory preset slot
until the sound returns. There is a brief
mute while the radio saves the station.
Sound returns when finished. When
switching to an HD2 or HD3 memory
preset, the sound mutes before the
digital audio plays, because the system
has to reacquire the digital signal.

Note: As with any saved radio station, you
cannot access the saved station if your
vehicle is outside the station’s reception
area.
HD Radio Reception and Station Troubleshooting
Potential reception issues

Reception area

Station blending

380

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)

Potential station issues
Issues

Echo, stutter, skip or repeat
in audio.
Increase or decrease in
audio volume.

Cause

Action

This is poor time alignment No action required. This is a
by the radio broadcaster.
broadcast issue.

Sound fading or blending in The radio is shifting between No action required. The
and out.
analog and digital audio.
reception issue may clear up
as you continue to drive.

There is an audio mute
delay when selecting HD2 or
HD3, multicast preset or
Direct Tune.

The digital multicast is not No action required. This is
available until the HD Radio normal behavior. Wait until
broadcast is decoded. Once the audio is available.
decoded, the audio is available.

Cannot access HD2 or HD3
multicast channel when
recalling a preset or from a
direct tune.

The previously stored
No action required. The
multicast preset or direct
station is not available in
tune is not available in your your current location.
current reception area.

Text information does not
match currently playing
audio.

Data service issue by the
radio broadcaster.

Fill out the station issue
form at website listed
below.

There is no text information Data service issue by the
shown for currently selected radio broadcaster.
frequency.

Fill out the station issue
form at website listed

HD2-HD7 stations not found Pressing Scan disables
when Scan is pressed.
HD2-HD7 channel search.

No action required. This is
normal behavior.

below.

http://www.ibiquity.com/automotive/report_radio_station_experiences
Radio Voice Commands

If you are listening to the radio,
press the voice button on the
E142599
steering wheel controls. When
prompted, say any of the following
commands.
If you are not listening to the radio, press
the voice button and, after the tone, say
"Radio", then any of the following
commands.

381

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
"RADIO"
"RADIO"

"Tune"

"<87.9-107.9>"

"Help"

"<87.9-107.9> HD"

"<530-1710>"

If available.

If you have said "Browse", see the
"Browse" chart later in this section.

"AM"

If you have said "Tune", see the following
"Tune" chart.

"AM <530-1710>"
"AM autoset"
"AM autoset preset <#>"

"TUNE"

"AM preset <#>"

"<530-1710>"

"Browse"

"<87.9-107.9>"

"FM"

"<87.9-107.9> HD <#>"

"FM <87.9-107.9>"

"AM"

"FM <87.9-107.9> HD <#>"

"AM <530-1710>"

"FM autoset"

"AM autoset"

"FM autoset preset <#>"

"AM autoset preset <#>"

"FM preset <#>"

"AM preset <#>"

"FM 1"

"FM"

"FM 1 preset <#>"

"FM <87.9-107.9>"

"FM 2"

"FM <87.9-107.9> HD <#>"

"FM 2 preset <#>"

"FM autoset"

"HD <#>"

"FM autoset preset <#>"

"FM preset <#>"

"Preset <#>"
"Radio off"

"FM 1"

"Radio on"

"FM 1 preset <#>"

"Set PTY"

"FM 2"
"FM 2 preset <#>"

382

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Scan

"TUNE"

"HD <#>"

Touch this button to hear a brief sampling
of channels.

"Preset <#>"

Options

"Help"
*

Touch this button to view and adjust
various media settings.

If available.

Sound Settings

SIRIUS® Satellite Radio (If
Activated)

E142611

Touch this button to adjust settings for:
•
•
•
•
•
•
•

Press the lower left corner of the
touchscreen, and then select the
SIRIUS tab.

Memory Presets
Save a channel by pressing and holding
one of the memory preset areas. There is
a brief mute while the radio saves the
channel. Sound returns when finished.

Note: Your vehicle may not have all these
sound settings.

ALERT

Set Category for Seek/Scan

Save the current song, artist, or team as a
favorite. The system alerts you when it
plays again on any channel.

This allows you to select a category of
music you would like to search for. You can
then choose to either seek or scan for the
stations playing that category.

Replay
Replay audio on the current channel. You
can replay approximately 45 minutes of
audio as long as you have remained tuned
to the current station. Changing stations
erases the previous audio.

Parental Lockout
This allows you to lock and unlock
channels, change or reset your PIN or
unlock all channels. To use this feature,
you need your initial PIN, which is 1234.

While in replay mode:
• Press and release the seek buttons to
hear the previous or next song.
• Press and hold the seek buttons to
reverse or fast forward in the current
track.
• Press play or pause to play or pause
the audio.
• Press Replay to return to live audio if
you have been using the feature to
replay audio.

Artist/Title/Team Alerts
This feature allows you to select Artists,
Titles and Teams that you would like the
system to alert you to when they are
playing on other channels. Press Edit Alerts
to delete or turn off alerts. You can also
set all alerts to on or off. When an alert
appears on the screen, you can choose to

383

F150 (TF6) , enUSA

Bass
Midrange
Treble
Balance and Fade
DSP (Digital Signal processing)
Occupancy Mode
Speed Compensated Volume.

MyFord Touch™ (If Equipped)
Tune to the channel, to Cancel the alert or
to Disable Alerts. If you are listening to a
sporting event, you can save your favorite
teams so that the system can alert you
when they are playing on a satellite radio
channel.
E142593

Note: SIRIUS does not support the Alert
feature on all channels. Ford Motor
Company shall not be responsible for Alert
feature variation.

SIRIUS satellite radio is a
subscription-based satellite radio service
that broadcasts a variety of music, sports,
news, weather, traffic and entertainment
programming. Your factory-installed
SIRIUS satellite radio system includes
hardware and a limited subscription term
that begins on the date of sale or lease of
your vehicle. See an authorized dealer for
availability.

Electronic Serial Number (ESN)
SIRIUS requires this number when
communicating with you about your
account.
Direct Tune

For more information on extended
subscription terms (a service fee is
required), the online media player and a
list of SIRIUS satellite radio channels, and
other features, please visit
www.siriusxm.com in the United States,
www.sirius.ca in Canada, or call SIRIUS at
1-888-539-7474.

Touch this button to manually enter the
desired satellite channel number. Touch
Enter when you are done.
Browse
Touch this button to view a list of all
available stations. Scroll to see more
categories. Touch the station you want to
listen to.

Note: This receiver includes the eCos
real-time operating system. eCos is
published under the eCos License.

Touch Skip if you want to skip this
channel.

Satellite Radio Electronic Serial Number
(ESN)

Touch Lock if you do not want anyone to
listen to this channel.

You need your ESN to activate, modify or
track your satellite radio account. The ESN
is on the System Information Screen (SR
ESN:XXXXXXXXXXXX). To access your
ESN, touch the bottom left corner of the
touchscreen. Touch SIRIUS > Options.

Touch Title or Artist to see song and
artists on other stations.
SIRIUS Satellite Radio Information
Note: SIRIUS reserves the unrestricted right
to change, rearrange, add or delete
programming including canceling, moving
or adding particular channels, and its prices,
at any time, with or without notice to you.
Ford Motor Company shall not be
responsible for any such programming
changes.

384

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
SIRIUS Satellite Radio Reception Factors and Troubleshooting
Potential reception issues

Antenna obstructions

For optimal reception performance, keep the antenna
clear of snow and ice build-up and keep luggage and other
materials as far away from the antenna as possible.

Terrain

Hills, mountains, tall buildings, bridges, tunnels, freeway
overpasses, parking garages, dense tree foliage and
thunderstorms can interfere with your reception.

Station overload

When you pass a ground-based broadcast-repeating
tower, a stronger signal may overtake a weaker one and
the audio system may mute.

Satellite radio signal interfer- Your display may show ACQUIRING... to indicate the
ence
interference and the audio system may mute.

Troubleshooting tips
Radio display

Cause

Action

Acquiring...

Radio requires more than
two seconds to produce
audio for the selected
channel.

Sat Fault/SIRIUS System
Failure.

There is an internal module If this message does not
clear shortly, or with an ignior system failure present.
tion key cycle, your receiver
may have a fault. See an
authorized dealer for service.

Invalid Channel.

The channel is no longer
available.

Tune to another channel or
choose another preset.

Unsubscribed Channel.

Your subscription does not
include this channel.

Contact SIRIUS at 1-888539-7474 to subscribe to
the channel, or tune to
another channel.

No Signal.

The signal is lost from the
SIRIUS satellite or SIRIUS
tower to your vehicle
antenna.

The signal is blocked. When
you move into an open area,
the signal should return.

385

F150 (TF6) , enUSA

No action required. This
message should disappear
shortly.

MyFord Touch™ (If Equipped)
Troubleshooting tips
Radio display

Cause

Action

Updating.

Update of channel
programming in progress.

No action required. The
process may take up to
three minutes.

Call SIRIUS
1-888-539-7474.

Your satellite service is no
longer available.

Contact SIRIUS at 1-888539-7474 to resolve
subscription issues.

SIRIUS has updated the
channels available for your
vehicle.

"SIRIUS"

SIRIUS Satellite Radio Voice
Commands

"SAT 2 preset <#>"

If you are listening to SIRIUS
satellite radio, press the voice
button on the steering wheel
controls. When prompted, say any of the
following commands.

"SAT 3"

E142599

"SAT 3 preset <#>"
"Sirius <0-223>"

If you are not listening to SIRIUS satellite
radio, press the voice button and, after the
tone, say "SIRIUS", then any of the
following commands.

"Sirius off"
"Sirius on"
"Sports game"

"SIRIUS"

"Tune"

"Help"

"Preset <#>"

If you have said "Sports game", see the
following "Sports game" chart.

"SAT"

If you have said "Tune", see the following
"Tune" chart.

"SAT preset <#>"
"SAT 1"
"SAT 1 Preset <#>"
"SAT 2"

386

F150 (TF6) , enUSA

No action required.

MyFord Touch™ (If Equipped)
Shuffle
"SPORTS GAME"

Touch this button to play the tracks or
entire albums in random order, or turn the
feature off if already on.

"Tune to the game"
"Tune to the game"

Scan

"Tune to the
game"

Touch this button to hear a brief sampling
of all available tracks.

"Tune to the game"

More Info

"Help"

Touch this button to see disc information.
Options

"TUNE"

Sound Settings

Touch this button to adjust settings for:

"Preset <#>"

•
•
•
•
•
•
•

"SAT"
"SAT 1"
"SAT 1 preset <#>"
"SAT 2"
"SAT 2 preset <#>"
"SAT 3"

Note: Your vehicle may not have all these
sound settings.

"SAT 3 preset <#>"

Compression

"Sirius <0-223>"

Touch this button to turn the compression
feature on and off.

"Help"

E142611

Browse
Press the lower left corner of the
touchscreen, and then select the
CD tab.

Touch this button to look through all
available CD tracks.
CD Voice Commands

You can also advance and reverse the
current track or current folder, if applicable.

If you are listening to a CD, press
the voice button on the steering
wheel controls. When prompted,
say any of the following commands.
E142599

Repeat
Touch this button to repeat the currently
playing track, all tracks on the disc or turn
the feature off if already on.

If you are not listening to a CD, press the
voice button and, after the tone, say "CD",
then any of the following commands.
387

F150 (TF6) , enUSA

Bass
Midrange
Treble
Balance and Fade
DSP (Digital Signal processing)
Occupancy Mode
Speed Compensated Volume.

MyFord Touch™ (If Equipped)

"CD"

"Pause"
"Play"
"Play next track"
"Play previous track"
"Play track <1-512>"
E142619

"Repeat"

The SD card slot is located either in the
center console or behind a small access
door in the instrument panel. To access
and play music from your device, press the
lower left corner of the touchscreen.

"Repeat folder"
"Repeat off"
"Repeat track"
"Shuffle"
"Shuffle CD"

"Shuffle folder"
"Shuffle off"

E142620

"Help"
*

SD logo is a trademark of SD-3C, LLC.

This applies to WMA or MP3 files only.

USB Port

SD Card Slot and USB Port
SD Card
Note: Your SD card slot is spring-loaded.
To remove the SD card, press the card in
and the system ejects it. Do not attempt to
pull the card to remove it as this could cause
damage.
Note: The navigation system also uses this
card slot. See Navigation (page 410).
E142621

The USB ports are located either in the
center console or behind a small access
door in the instrument panel. To access
and play music from your device, press the
lower left corner of the touchscreen.

388

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
This feature allows you to plug in media
playing devices, memory sticks, flash drives
or thumb drives, and charge devices if they
support this feature.
In order to playback video from your iPod
or iPhone, you must have a special
combination USB/RCA composite video
cable (which you can buy from Apple).
When you connect the cable to your iPod
or iPhone, plug the other end into both the
RCA jacks and the USB port.

Sound Settings allows you to adjust
settings for:
• Bass
• Midrange
• Treble
• Balance and Fade
• DSP (Digital Signal processing)
• Occupancy Mode
• Speed Compensated Volume.

Playing Music from Your Device

Note: Your vehicle may not have all these
sound settings.

Note: The system is capable of indexing up
to 30,000 songs.

Media Player Settings allows you to
select more settings, which is under Media
Player. See Settings (page 366).

Insert your device and select the
SD Card or USB tab once the
system recognizes it. You can
then select from the following options:

Device Information displays software
and firmware information about the
currently connected media device.

E142611

Update Media Index indexes your device
when you connect it for the first time and
each time the content changes (such as
adding or removing tracks) to make sure
you have the latest voice commands
available for all media on the device.

Repeat
This feature replays the currently playing
song or album.
Shuffle
Touch this button to play music on the
selected album or folder in random order.

Browse
This feature allows you to view the
contents of the device. It also allows you
to search by categories, such as genre,
artist or album.

Similar Music
This feature allows you to choose music
similar to what is currently playing.

If you want to view song information such
as Title, Artist, File, Folder, Album, and
Genre, touch the on-screen album art.

More Info
Touch this button to see disc information
such as current track, artist name, album
and genre.

You can also touch What’s Playing to
hear how the system pronounces the
current band and song. This can be helpful
when using voice commands to make sure
the system correctly plays your request.

Options
Touch this button to view and adjust
various media settings.

389

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Playing Video from Your Device

"USB" or "SD CARD"

To access and play video from your device,
your vehicle's transmission must be in
position P with the ignition in accessory
mode. See Starting and Stopping the
Engine (page 135).

"Play podcast "
"Play podcast episode "
"Play similar music"
"Play song "

SD Card and USB Voice Commands
If you are listening to a USB
device or an SD card, press the
E142599
voice button on the steering
wheel controls. When prompted, say any
of the following commands.

"Play TV show "

"Play TV show episode "
**

"Play video podcast "

"Play video playlist "

"Previous"

"Repeat all"

"Next"

"Repeat off"

"Pause"

"Repeat one"

"Play"

"Shuffle"

"Play album "

"Shuffle album"

"Play all"

"Shuffle off"

"Play artist "

"What's this?"

"Play audiobook "

"Help"

"Play author "

If you have said you would like to browse
your USB or SD card, the system prompts
you to specify what you would like to
browse. When prompted, see the following
"Browse" chart.

"Play composer "
"Play folder "
"Play genre "

These commands are only available in
USB mode and are device-dependent.

"Play music video "
"Play playlist "

390

F150 (TF6) , enUSA

"Play video podcast episode "

"USB" or "SD CARD"

"Play movie "

"Play video "

If you are not listening to a USB device or
an SD card, press the voice button and,
after the tone, say "USB" or "SD card",
then any of the following commands.

"Browse"

MyFord Touch™ (If Equipped)
"BROWSE"
"BROWSE"

"TV show "

"Album "

"All albums"

"Video "

"All artists"

"Video playlist "

"All audiobooks"

This command is only available in USB
mode and is device-dependent.

"All folders"
"All genres"

Supported Media Players, Formats
and Metadata Information

"All music videos"

SYNC is capable of hosting nearly any
digital media player, including iPod,
Zune™, plays from device players, and
most USB drives. Supported audio formats
include MP3, WMA, WAV and AAC.

"All playlists"
"All podcasts"

It is also able to organize your indexed
media from your playing device by
metadata tags. Metadata tags, which are
descriptive software identifiers embedded
in the media files, provide information
about the file.

"All songs"
*

"All TV shows"

"All video playlists"

"All video podcasts"
"All videos"

"Help"

"All composers"

"All movies"

"Video podcast "

"All authors"

If your indexed media files contain no
information embedded in these metadata
tags, SYNC may classify the empty
metadata tags as Unknown.

"Artist "

In order to playback video from your iPod
or iPhone, you must have a special
combination USB/RCA composite video
cable (which you can buy from Apple).
When you connect the cable to your iPod
or iPhone, plug the other end into both the
RCA jacks and the USB port.

"Audiobook "
"Author "
"Composer "
"Folder "

Bluetooth Audio

"Genre "

Your system allows you to stream audio
over your vehicle's speakers from your
connected, Bluetooth-enabled cellular
phone.

"Playlist "
"Podcast "

391

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)

E142611

To access, press the lower left
corner on the touchscreen, then
select the BT Stereo tab.

Bluetooth Audio Voice Commands
If you are listening to a Bluetooth
audio device, press the voice
button on the steering wheel
control. When prompted, say "Next song",
"Pause", "Play" or "Previous song".
E142599

E142622

If you are not listening to a Bluetooth audio
device, press the voice button and, after
the tone, say "Next song", "Pause", "Play"
or "Previous song".

Your A/V inputs allow you to connect an
auxiliary audio/video source (such as a
gaming systems or a personal camcorder)
by connecting RCA cords (not included)
to these input jacks. The jacks are yellow,
red and white and are located either
behind a small access door on the
instrument panel or in your center console.

A/V Inputs
WARNINGS
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any handheld device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

You can also use the A/V inputs as an
auxiliary input jack to play music from your
portable music player over your vehicle's
speakers. Plug in your 1/8 inch (3.5
millimeter) RCA adapter into the two left
A/V input jacks (red and white).
Press the lower left corner of the
touchscreen, and then select A/V In.
To use the auxiliary input jack feature,
make sure that your portable music player
is designed for use with headphones and
that it is fully charged. You also need an
audio extension cable with stereo male
1/8-inch (3.5 millimeter) connectors at one
end and a RCA jack at the other.

For safety reasons, do not connect
or adjust the settings on your
portable music player while your
vehicle is moving.

Switch off the engine, radio and
portable music player. Set the parking
brake and put the transmission in
position P.
2. Attach one end of the audio extension
cable to the headphone output of your
player and the other end into the
adapter in one of the two left A/V input
jacks (white or red) inside the center
console.

Store the portable music player in a
secure location, such as the center
console or the glove box, when your
vehicle is moving. Hard objects may
become projectiles in a crash or sudden
stop, which may increase the risk of serious
injury. The audio extension cable must be
long enough to allow the portable music
player to be safely stored while your
vehicle is moving.

392

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
3. Press the lower left corner on the
touchscreen. Select either a tuned FM
station or a CD (if there is a CD already
loaded into the system).
4. Adjust the volume as desired.
5. Turn the portable music player on and
adjust the volume to ½ the maximum.
6. Press the lower left corner on the
touchscreen. Select the A/V In tab.
(You should hear audio from your
portable music player although it may
be low.)
7. Adjust the sound on your portable
music player until it reaches the level
of the FM station or CD by switching
back and forth between the controls.

Troubleshooting

•

PHONE

A
B
C
D
E
F
E161968

393

F150 (TF6) , enUSA

Do not connect the audio input jack to
a line level output. The jack only works
correctly with devices that have a
headphone output with a volume
control.
Do not set the portable music player's
volume level higher than is necessary
to match the volume of the CD or FM
radio as this causes distortion and
reduces sound quality.
If the music sounds distorted at lower
listening levels, turn the portable music
player volume down. If the problem
persists, replace or recharge the
batteries in the portable media player.
Control the portable media player in
the same manner when used with
headphones, as the auxiliary input jack
does not provide control (such as Play
or Pause) over the attached portable
media player.

MyFord Touch™ (If Equipped)
A

Phone

Quick Dial

Phonebook

History

Messaging

Settings

Pairing Your Phone for the First
Time

Hands-free calling is one of the main
features of SYNC. Once you pair your
phone, you can access many options using
the touchscreen or voice commands. While
the system supports a variety of features,
many are dependent on your cellular
phone’s functionality.

WARNING
Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any handheld device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

At a minimum, most cellular phones with
Bluetooth wireless technology support the
following functions:
• Answering an incoming call.
• Ending a call.
• Using privacy mode.
• Dialing a number.
• Redialing.
• Call waiting notification.
• Caller ID.

The first thing you must do to use the
phone features of SYNC is to pair your
Bluetooth-enabled cellular phone with
SYNC. This allows you to use your phone
in a hands-free manner.

Other features, such as text messaging
using Bluetooth and automatic phonebook
download, are phone-dependent features.
To check your phone’s compatibility, see
your phone’s user manual and visit
www.SYNCMyRide.com,
www.SYNCMyRide.ca or
www.syncmaroute.ca.

Note: Put the transmission in park (P).
Switch on your vehicle ignition and the radio.
Touch Add Phone in the upper left
corner of the touchscreen. Find SYNC
appears on the screen, and instructs
you to begin the pairing process from
your device.
2. Make sure that Bluetooth is set to On
and that your cellular phone is in the
proper mode. See your phone’s manual
if necessary.

394

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
SYNC may prompt you with more phone
options. For more information on your
phone's capability, see your phone's
manual and visit the website.

Note: Select SYNC, and a six-digit PIN
appears on your device.
3. If prompted to enter a PIN on your
device, it does not support Secure
Simple Pairing. To pair, enter the PIN
displayed on the touchscreen. Skip the
next step.
4. When prompted on your phone’s
display, confirm that the PIN provided
by SYNC matches the PIN displayed
on your cellular phone.
5. The display indicates when the pairing
is successful.

Making Calls
Press the voice button on your
steering wheel controls. When
E142599
prompted, say, "Call "
or say "Dial", then the desired number.

E165966

SYNC may prompt you with more phone
options. For more information on your
phone's capability, see your phone's
manual and visit the website.

Receiving Calls
During an incoming call, an audible tone
sounds. Call information appears in the
display if it is available.

Pairing Subsequent Phones

Accept the call by pressing
Accept on the touchscreen or
E165966
by pressing the phone button on
your steering wheel controls.

Note: Put the transmission in park (P).
Switch on your vehicle ignition and the radio.
Press the Phone corner of the
touchscreen > Settings > BT Devices
> Add Device.
2. Make sure that Bluetooth is set to On
and that your cellular phone is in the
proper mode. See your phone’s manual
if necessary.
Note: Select SYNC, and a six-digit PIN
appears on your device.
1.

Reject the call by pressing Reject on the
touchscreen or by pressing and holding the
phone button on your steering wheel
controls.
Ignore the call by doing nothing. SYNC logs
it as a missed call.

Phone Menu Options

3. If prompted to enter a PIN on your
device, it does not support Secure
Simple Pairing. To pair, enter the PIN
displayed on the touchscreen. Skip the
next step.
4. When prompted on your phone’s
display, confirm that the PIN provided
by SYNC matches the PIN displayed
on your cellular phone.
5. The display indicates when the pairing
is successful.

Press the top left corner on your
touchscreen to select from the following
options:
Phone
Touch this button to access the on-screen
numerical pad to enter a number and place
a call. During an active call, you can also
choose to:
• Mute the call.
• Put the call on hold.
• Turn on the privacy feature.

395

F150 (TF6) , enUSA

To end the call or exit phone
mode, press and hold the phone
button.

MyFord Touch™ (If Equipped)
•
•

Text Messaging

Join two calls.
End the call.

Note: Downloading and sending text
messages using Bluetooth are
phone-dependent features.

Quick Dial
Set up favorite contacts from you
phonebook or history folder.

Note: Certain features in text messaging
are speed-dependent and not available
when your vehicle is traveling at speeds over
3 mph (5 km/h).

Phonebook
Touch this button to access and call any
contacts in your previously downloaded
phone book. The system places the entries
in alphabetical categories summarized at
the top of the screen.

Note: SYNC does not download read text
messages from your phone.
You can send and receive text messages
using Bluetooth, read them aloud and
translate text messaging acronyms, such
as LOL.

To switch on contact picture settings, if
your device supports this feature, press
Phone > Settings > Manage Phonebook
> Download photos from Phonebook
> On.

Touch the top left corner of the display
to access the Phone menu.
2. Select Messaging.
3. Choose from the following:
• Listen (speaker icon).
• Dial.
• Send Text.
• View.
• Delete.

History
After you connect your Bluetooth-enabled
phone to SYNC, you can access any
previously dialed, received or missed calls.
You can also choose to save these to your
Favorites or to Quick Dial.
Note: This is a phone-dependent feature.
If your phone does not support downloading
call history using Bluetooth, SYNC keeps
track of calls made with the SYNC system.

Composing a Text Message

Messaging

Note: This is a speed-dependent feature.
It is unavailable when your vehicle is
traveling at speeds over 3 mph (5 km/h).

Send text messages using your
touchscreen. See Text messaging later
in this section.

Note: Downloading and sending text
messages using Bluetooth are
phone-dependent features.
1.

Touch the top left corner of the display
to access the Phone menu.
2. Touch Messaging > Send Text.
3. Enter a phone number or choose from
your phonebook.
4. You can select from the following
options:

Settings
Touch this button to access various phone
settings, such turning Bluetooth on and off,
managing your phonebook and more. See
Phone settings later in this section.

396

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
•
•

When a new message arrives, an audible
tone sounds and the screen displays a
pop-up with the caller name and ID, if
supported by your phone. You can press:
• View to view the text message.
• Listen for SYNC to read the message
to you.
• Dial to call the contact.
• Ignore to exit the screen.

Send, which sends the message as it
is.
Edit Text, which allows you to
customize the pre-defined message or
create a message on your own.

You can then preview the message, verify
the recipient as well as update the
message list.
Text message options

Phone Settings

I’ll call you back in a few minutes.

Press Phone > Settings.

I just left, I’ll be there soon.

Bluetooth Devices

Can you give me a call?

Touch this tab to connect, disconnect, add
or delete a device, as well as save it as a
favorite.

I’m on my way.
I’m running a few minutes late.

Bluetooth

I’m ahead of schedule, so I’ll be there
early.

Touch this tab to turn Bluetooth off or on.

I’m outside.

Do Not Disturb

I’ll call you when I get there.

Touch this tab if you want all calls to go
directly to your voice mail and not ring in
the vehicle. When this feature is on, text
message notifications do not ring inside
the cabin either.

OK
Yes
No

911 Assist

Thanks

Turn on or turn off the 911 Assist feature.
See Information (page 399).

Stuck in traffic.
Call me later.

Phone Ringer

LOL

Select the ring tone you want to hear when
you receive a call. Choose from possible
system ring tones, your currently paired
phone’s ring tone, a beep, text-to-speech
or a silent notification.

Receiving a Text Message
Note: If you select View and your vehicle
is traveling over 3 mph (5 km/h), the system
offers to read the message to you instead
of allowing you to view it while driving.

397

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Text Message Notification

"PHONE"

Select a text message notification, if
supported by your phone. Choose from
possible system alert tones,
text-to-speech or silent.

"Call on other"
"Call voicemail"
"Dial"

Internet Data Connection

"Do not disturb off"

If your phone is compatible, use this screen
to adjust your internet data connection.
Select to make your connection profile
with the personal area network or to switch
off your connection. You can also choose
to adjust your settings or have the system
always connect, never connect when
roaming or query on connect. Press ? for
more information.

"Do not disturb on"
"Forward text messages"
"Go to hands free"

"Hold call off"
*

"Hold on"

Manage Phonebook

"Join calls"

Touch this button to access features such
as automatic phonebook download,
re-download your phonebook, add
contacts from your phone as well as delete
or upload your phonebook.

"Listen to text message <#>"
"Listen to text messages"
"Messages"

Roaming Warning
"Mute call"

Touch this button to have the system alert
you when your phone is in roaming mode.

"Pair phone"

Phone Voice Commands

"Privacy on"

Press the voice button on the
steering wheel controls. When
E142599
prompted, say any of the
following commands:

"Read text message"
"Reply to text messages"
"Turn ringer off"
"Turn ringer on"

"PHONE"

"Call"
"Call "
"Call at home"
"Call at work"
"Call on cell"

398

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
"PHONE"
"MESSAGES"
*

"Unmute call"

"Call"

"Help"

"Forward text messages"

This command is only available during an
active call.

"Listen to text message <#>"
"Listen to text messages"

If you say "Messages", see the following
"Messages" chart for additional
commands.

"Reply to text messages"
"Help"

INFORMATION

A
B
C
D
E

E161889

SYNC Services

Sirius Travel Link

Alerts

Calendar

SYNC Applications

399

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Under the Information menu, you can
access features such as:
• SYNC Services
• Sirius Travel Link
• Alerts
• Calendar
• SYNC Applications
If your vehicle is equipped with
Navigation, press the
Information button to access
these features. If your vehicle is not
equipped with Navigation, press the corner
of the touchscreen with the green tab.
E142608

SYNC Services (If Equipped,
United States Only)
Note: SYNC Services varies by trim level
and model year and may require a
subscription. Traffic alerts and turn-by-turn
directions available in select markets.
Message and data rates may apply. Ford
Motor Company reserves the right to change
or discontinue this product service at any
time without prior notification or incurring
any future obligation.
Note: SYNC Services requires activation
before use. Visit www.SYNCMyRide.com to
register and check your eligibility for
complimentary services. Standard phone
and message rates may apply. Subscription
may be required. You must also have the
active SYNC Services Bluetooth-enabled
cellular phone paired and connected to the
system in order to connect to, and use,
SYNC Services. See Phone (page 393).

Note: The driver is ultimately responsible
for the safe operation of the vehicle, and
therefore, must evaluate whether it is safe
to follow the suggested directions. Any
navigation features provided are only an aid.
Make your driving decisions based on your
observations of local conditions and existing
traffic regulations. Do not follow the route
suggestions if doing so would result in an
unsafe or illegal maneuver, if you would be
placed in an unsafe situation, or if you would
be directed into an area that you consider
unsafe. Maps used by this system may be
inaccurate because of errors, changes in
roads, traffic conditions or driving
conditions.
Note: When you connect, the service uses
GPS technology and advanced vehicle
sensors to collect your vehicle's current
location, travel direction and speed to help
provide you with the directions, traffic
reports, or business searches you request.
Further, to provide the services you request,
for continuous improvement, the service
may collect and record call details and voice
communications. For more information, see
SYNC Services Terms and Conditions at
www.SYNCMyRide.com. If you do not want
Ford or its service providers to collect your
vehicle travel information or other
information identified in the Terms and
Conditions, do not subscribe or use the
service.
SYNC Services uses advanced vehicle
sensors, integrated GPS technology and
comprehensive map and traffic data, to
give you personalized traffic reports,
precise turn-by-turn directions, business
search, news, sports, weather and more.
For a complete list of services, or to learn
more, please visit www.SYNCMyRide.com.

Note: This feature does not function
properly if you have enabled caller ID
blocking on your cellular phone. Make sure
your cellular phone is not blocking caller ID
before using SYNC Services.

Connecting to SYNC Services Using
Voice Commands

E142599

400

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
1. Press the voice button.
2. When prompted, say "Services". This
initiates an outgoing call to SYNC
Services using your paired and
connected Bluetooth-enabled cellular
phone.
3. Once you connect to the service, follow
the voice prompts to request the
desired service, such as "Traffic" or
"Directions". You can also say, "What
are my choices?" to receive a list of
available services from which to
choose.
4. Say, "Services" to return to the Services
main menu or for help, say, "Help".

assistance in finding a location you can
say "Operator" at any time within a
Directions or Business search to speak
with a live operator. The system may
prompt you to speak with an operator
when it has difficulty matching your
voice request. The live operator can
assist you by searching for businesses
by name or by category, residential
addresses by street address or by
name or specific street intersections.
Operator Assist is a feature of your
SYNC Services subscription. For more
information on Operator Assist, visit
www.SYNCMyRide.com/support.
2. Follow the voice prompts to select your
Destination. After the route download
is finished, the phone call automatically
ends.

Connecting to SYNC Services Using
the Touchscreen

E142608

If your vehicle is equipped with
Navigation, press the
Information button.

If your vehicle is not equipped with
Navigation:
• Turn-by-turn directions appear in the
information display, in the status bar
of your touchscreen system and on the
SYNC Services screen. You also receive
driving instructions from audible
prompts.
• When on an active route, you can
select Route Summary or Route
Status using the touchscreen controls
or voice commands to view the Route
Summary Turn List or the Route
Status ETA. You can also turn voice
guidance on or off, cancel the route or
update the route.

If your vehicle is not equipped with
Navigation, press the green tab on your
touchscreen.
1.

Select Connect to Services to initiate
an outgoing call to SYNC Services
using your phone.
2. Once connected, follow the voice
prompts to request your desired
Service, such as "Traffic" or
"Directions". You can also say, "What
are my choices?" to receive a list of
available services from which to
choose.
3. Say, "Services" to return to the Services
main menu or for help, say, "Help".

If you miss a turn, SYNC automatically asks
if you want the route updated. Just say,
"Yes" when prompted and the system
delivers a new route to your vehicle.

Receiving Turn-by-Turn Directions
1.

If your vehicle is equipped with Navigation,
SYNC Services downloads your requested
destination to the navigation system. The
navigation system then calculates the
route and provides driving instructions.
See Navigation (page 410).

401

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Disconnecting from SYNC Services
1.

button on the steering wheel.
2. Say "Good-bye" from the SYNC
Services main menu.

Press and hold the hang-up phone

SYNC Services quick tips

Personalizing

You can personalize your Services feature to provide
quicker access to your most used or favorite information.
You can save address points, such as work or home. You
can also save favorite information like sports teams, such
as Detroit Lions, or a news category. You can learn more
about personalization by logging onto
www.SYNCMyRide.com.

Push to interrupt

Press the voice button at any time (while connected to
SYNC Services) to interrupt a voice prompt or an audio
clip (such as a sports report) and say your voice command.

Portable

SYNC Services Voice Commands

"Services"

When a route has been
downloaded (non-navigation
E142599
systems), press the voice button
on the steering wheel controls. When
prompted, say any of the following
commands:

"Update route"
"Help"

Sirius Travel Link (If Equipped)
WARNING

"SERVICES"

Driving while distracted can result in
loss of vehicle control, crash and
injury. We strongly recommend that
you use extreme caution when using any
device that may take your focus off the
road. Your primary responsibility is the safe
operation of your vehicle. We recommend
against the use of any handheld device
while driving and encourage the use of
voice-operated systems when possible.
Make sure you are aware of all applicable
local laws that may affect the use of
electronic devices while driving.

"Cancel route"
"Navigation voice off"
"Navigation voice on"
"Next turn"
"Route status"
"Route summary"

402

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Note: In order to use Sirius Travel Link, your
vehicle must be equipped with navigation
and your navigation SD card must be in the
SD card slot.

Weather
Touch this button to view the nearby
weather, current weather, or the five day
forecast for the chosen area. Select Map
to see the weather map, which can show
storms, radar information, charts and
winds. Select Area to select from a listing
of weather locations.

Note: A paid subscription is required to
access and use these features. Go to
www.siriusxm.com/travellink for more
information.
Note: Visit www.siriusxm.com/traffic# and
click on Coverage map and details for a
complete listing of all traffic areas covered
by Sirius Travel Link.

Sports Info
Touch this button to view scores and
schedules from a variety of sports. You can
also save up to 10 favorite teams for easier
access. The score automatically refreshes
when a game is in progress.

Note: Neither Sirius nor Ford is responsible
for any errors or inaccuracies in the Sirius
Travel Link services or its use in vehicles.
When you subscribe to Sirius Travel Link,
it can help you locate the best gas prices,
find movie listings, get current traffic alerts,
view the current weather map, get
accurate ski conditions and see scores to
current sports games.

Ski Conditions

If your vehicle is equipped with
Navigation, touch the i
E142608
(Information) button to access
these features. If your vehicle is not
equipped with Navigation, touch the corner
of the touchscreen with the green tab.

Press the voice button on the
steering wheel controls. When
E142599
prompted, say any of the
following commands:

Touch this button to view ski conditions
for a specific area.
Sirius Travel Link Voice Commands

"SIRIUS TRAVEL LINK"

Traffic On Route and Traffic Nearby

"5-day weather forecast"

Touch these buttons to identify traffic
incidents on your route, nearby your
vehicle’s current location or near any of
your favorite places, if programmed.

"Fuel prices"
"Movie listings"
"Sports headlines"

Fuel Prices

"Sports schedules"

Touch this button to view fuel prices at
stations close to your vehicle’s location or
on an active navigation route.

"Sports scores"
"Traffic"

Movie Listings

"Weather"

Touch this button to view nearby movie
theaters and their show times, if available.

403

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
"SIRIUS TRAVEL LINK"

Additional sports-related voice
commands

"Weather map"

"College football schedule"

"Help"

"College football scores"

If you say "Sports headlines", "Sports
schedules" or "Sports scores", you can
then say any of the commands in the
following chart.

"Golf headlines"
"Golf leaderboard"
"Golf schedule"

Sports-related commands

"MLS headlines"

"Baseball"

"MLS schedule"

"College basketball"

"MLS scores"

"College football"

"Motor sports headlines"

"Golf"

"Motor sports order"

"MLS"

"Motor sports schedule"

"My teams"

"My team headlines"

"NBA"

"My teams schedule"

"NFL"

"My teams scores"

"NHL"

"NBA headlines"

"WNBA"

"NBA schedule"

"Help"

"NBA scores"

Additional sports-related voice
commands

"NFL headlines"

"Baseball headlines"

"NFL scores"

"Baseball schedule"

"NHL headlines"

"Baseball scores"

"NHL schedule"

"College basketball headlines"

"NHL scores"

"College basketball schedule"

"WNBA headlines"

"NFL schedule"

"College basketball scores"
"College football headlines"

404

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
911 Assist (If Equipped)

Additional sports-related voice
commands

WARNINGS
Unless the 911 Assist setting is set on
before a crash, the system will not
dial for help, which could delay
response time, potentially increasing the
risk of serious injury or death after a crash.

"WNBA schedule"
"WNBA scores"
"Help"

Do not wait for 911 Assist to make an
emergency call if you can do it
yourself. Dial emergency services
immediately to avoid delayed response
time, which could increase the risk of
serious injury or death after a crash. If you
do not hear 911 Assist within five seconds
of the crash, the system or phone may be
damaged or non-functional.

Alerts
If your vehicle is equipped with
Navigation, touch the i
(Information) button to access
these features. If your vehicle is not
equipped with Navigation, touch the corner
of the touchscreen with the green tab.
E142608

Press Alerts, and then choose from any
of the following services:
• View the complete message.
• Delete the message.
• Delete All messages.

Always place your phone in a secure
location in your vehicle so it does not
become a projectile or damaged in
a crash. Failure to do so may cause serious
injury to someone or damage the phone,
which could prevent 911 Assist from
working properly.

This screen displays any system messages
(such as an SD card fault).
Note: The system alerts you to any
messages by turning the information icon
yellow. After you read or delete the
messages, the icon returns to white.

Note: The SYNC 911 Assist feature must be
set on prior to the incident.
Note: Before setting this feature on, make
sure that you read the 911 Assist Privacy
Notice later in this section for important
information.

Calendar
If your vehicle is equipped with
Navigation, touch the i
E142608
(Information) button to access
these features. If your vehicle is not
equipped with Navigation, touch the corner
of the touchscreen with the green tab.

Press Calendar. You can view the current
calendar by day, week or month.

Note: Every phone operates differently.
While SYNC 911 Assist works with most
cellular phones, some may have trouble
using this feature.

405

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
•

If a crash deploys an airbag (excludes knee
airbags and rear inflatable safety belts [if
equipped]) or activates the fuel pump
shut-off, your SYNC-equipped vehicle may
be able to contact emergency services by
dialing 911 through a paired and connected
Bluetooth-enabled phone. You can learn
more about the 911 Assist feature, visit
www.SYNCMyRide.com,
www.SYNCMyRide.ca or
www.syncmaroute.ca.

•

See Supplementary Restraints System
(page 39). Important information
regarding airbag deployment is in this
chapter.

In the Event of a Crash

See Roadside Emergencies (page 215).
Important information regarding the fuel
pump shut-off is in this chapter.

Not all crashes deploy an airbag or activate
the fuel pump shut-off (which would
trigger 911 Assist); however, SYNC tries to
contact emergency services if 911 Assist
triggers. If a connected phone sustains
damage or loses connection to SYNC,
SYNC searches for, and tries to connect
to, any available previously paired phone
and tries to make the call to 911.

Setting 911 Assist On
If your vehicle is equipped with
Navigation, touch the i
(Information) button to access
these features. If your vehicle is not
equipped with Navigation, touch the corner
of the touchscreen with the green tab.
E142608

Touch Apps > 911 Assist, then select On.
You can also access 911 Assist
by:
E142607

•
•

Pressing the Settings icon > Settings
> Phone > 911 Assist, or
Pressing the Settings icon > Help > 911
Assist.

406

F150 (TF6) , enUSA

You must pair and connect a
Bluetooth-enabled and compatible
phone to SYNC.
A connected Bluetooth-enabled phone
must have the ability to make and
maintain an outgoing call at the time
of the incident.
A connected Bluetooth-enabled phone
must have adequate network coverage,
battery power and signal strength.
The vehicle must have battery power
and be located in the United States,
Canada or in a territory in which 911 is
the emergency number.

MyFord Touch™ (If Equipped)
Note: Your Vehicle Health Report feature
requires activation prior to use. Visit
www.SYNCMyRide.com to register. There
is no fee or subscription associated with
Vehicle Health Report, but you must register
to use this feature.

911 Assist May Not Work If
•
•
•

Note: This feature may not function
properly if you have enabled caller ID
blocking on your cellular phone. Before
running a report, review the Vehicle Health
Report Privacy Notice.

Vehicle Health Report (If Equipped)
WARNING
Always follow scheduled
maintenance instructions, regularly
inspect your vehicle, and seek repair
for any damage or problem you suspect.
Vehicle Health Report supplements, but
cannot replace, normal maintenance and
vehicle inspection. Vehicle Health Report
only monitors certain systems
electronically monitored by your vehicle
and will not monitor or report the status
of any other system, (such as brake lining
wear). Failure to perform scheduled
maintenance and regularly inspect your
vehicle may result in vehicle damage and
serious injury.

The system allows you to check your
vehicle’s overall health in the form of a
diagnostic report card. The Vehicle Health
Report contains valuable information, such
as:
• Vehicle diagnostic information
• Scheduled maintenance
• Open recalls and Field Service Actions
• Items noted during vehicle inspections
by your authorized dealer that still need
servicing.
Making a Report

Note: This feature is only available in the
United States.

E142608

407

F150 (TF6) , enUSA

If you want to run a report by
using the touchscreen, touch
Apps > Vehicle Health Report.

MyFord Touch™ (If Equipped)
To run a report by voice
command, press the voice
button on the steering wheel
and, when prompted, say "Vehicle health
report".

your cellular phone number or vehicle
information, do not run the feature or set
up your Vehicle Health Report profile at
www.SYNCMyRide.com. See
www.SYNCMyRide.com (Vehicle Health
Report Terms and Conditions, and Privacy
Statement) for more information.

E142599

Vehicle Health Report Privacy Notice
When you create a Vehicle Health Report,
Ford Motor Company may collect your
cellular phone number (to process your
report request) and diagnostic information
about your vehicle. Certain versions or
updates to Vehicle Health Report may also
collect more vehicle information. Ford may
use your vehicle information it collects for
any purpose. If you do not want to disclose

CLIMATE
Press the lower right corner on
the touchscreen to access your
E142612
climate control features.
Depending on your vehicle line and option
package, your climate screen may look
different from the screen shown here.

E166384

Power: Touch to switch the system off and on. Outside air cannot enter your
vehicle when you switch off the system.

Passenger settings: Touch + or – to adjust the temperature. Touch the heated
seat icon to control the heated seat. Touch the cooled seat icon to control the
cooled seat. See Seats (page 114).

Fan speed: Touch + or – to adjust fan speed.

408

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
D

Recirculated air: Touch to turn the recirculated air on or off which may reduce
the amount of time needed to cool down the interior and help reduce odors
from reaching the interior. Recirculated air also engages automatically when
you select MAX A/C and may turn on manually in any airflow mode except
defrost. It may also turn off in all airflow modes except MAX A/C to reduce fog
potential.

MAX A/C: Touch to cool your vehicle with recirculated air. Touch again for
normal A/C operation. MAX A/C distributes air through instrument panel vents
and may help reduce odors from entering your vehicle. MAX A/C is more
economical and efficient than normal A/C mode.

A/C: Touch to turn the air conditioning on or off. Use A/C with recirculated air
to improve cooling performance and efficiency. A/C engages automatically in
MAX A/C, defrost and footwell/defrost.

AUTO: Touch to engage automatic operation, then set the temperature using
the temperature control. The system automatically controls fan speed, airflow
distribution, A/C on or off and the use of fresh or recirculated air.

Rear defrost: Touch to turn the rear window defroster and heated mirrors.

Defrost: Touch to clear the windshield of fog and thin ice. Touch again to return
to the previous airflow selection. When on, defrost provides outside air to reduce
window fogging and distributes air through the windshield defroster vents and
demister vents.

Manual airflow distribution controls:Footwell and Defrost: Distributes
air through the windshield defroster vents, demister vents, floor vents and rear
seat floor vents, and provides outside air to reduce window fogging. Panel:
Distributes air through the instrument panel vents. Panel and Floor: Distributes
air through the instrument panel vents, demister vents, floor vents and rear seat
floor vents. Floor: Distributes air through the demister vents, floor vents and
rear seat floor vents.

Driver settings: Touch + or – adjust the temperature. Touch the heated seat
icon to control the heated seat. Touch the cooled seat icon to control the cooled
seat. See Seats (page 114). Touch and hold MyTemp to select a temperature
you would like your vehicle to remember and maintain for you.

Climate Control Voice Commands

Climate control commands

Press the voice button on the
steering wheel controls. When
E142599
prompted, say any of the
following commands:

"Climate automatic"
"Climate off"
"Climate on"
"Climate temperature <15.5-29.5>
degrees"

409

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Climate control commands

"CLIMATE"

"Climate temperature <60-85> degrees"

"Temperature <15.5-29.5> degrees"

"Climate my temp"

"Temperature <60-85> degrees"

"Help"

"Temperature decrease"
"Temperature high"

There are additional climate control
commands but in order to access them,
you have to say "Climate" first. When the
system is ready to listen, you may say any
of the following commands:

"Temperature increase"
"Temperature low"
"Windshield floor on"
"Help"

"CLIMATE"
*

"A/C off"

If you say "Temperature", you can then
say any of the commands in the following
chart.

"A/C on"
"Automatic"

"TEMPERATURE"

"Climate my temp"

"<15.5-29.5> degrees"

"Defrost off"

"<60-85> degrees"

"Defrost on"

"High"

"Dual off"

"Low"

"Fan decrease"

"Help"

"Fan increase"
"Floor on"

NAVIGATION

"MAX A/C off"
Note: The navigation SD card must be in
the SD card slot to operate the navigation
system. If you need a replacement SD card,
see an authorized dealer.

"MAX A/C on"
"Off"
"On"

Note: The SD card slot is spring-loaded. To
remove the SD card, just push the card in
and release it. Do not attempt to pull the
card out to remove it; this could cause
damage.

"Panel floor on"
"Panel on"
"Recirc off"

Your navigation system is comprised of
two main features, destination mode and
map mode.

"Recirc on"
*

"Temperature"

410

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
2. Select Set as Dest to make this your
destination. You can also choose to set
this as a waypoint (have the system
route to this point on the way to your
current destination) or save it as a
favorite. The system considers any
Avoid Areas selections in its route
calculation.
3. Choose from up to three different types
of routes, and then select Start Route.
• Fastest: Uses the fastest moving roads
possible.
• Shortest: Uses the shortest distance
possible.
• Eco Route: Uses the most fuel-efficient
route.

To set a destination, press the green corner
of your touchscreen, then the Dest button
when it appears. See Setting a
destination later in this chapter.
To view the navigation map and your
vehicle's current location, touch the green
bar in the upper right hand corner of the
touchscreen, or, press Dest, then Map. See
Map mode later in this chapter.

Setting a Destination
Press the green corner of your touchscreen,
then the Dest button when it appears.
Choose any of the following:
Destination

You can cancel the route or have the
system demo the route for you. Select
Route Prefs to set route preferences like
avoiding freeways, tollroads, ferries and
car trains as well as to use or not use
high-occupancy vehicle lanes.
(High-occupancy vehicle lanes are also
known as carpool or diamond lanes.
People who ride in buses, vanpools or
carpools use these lanes.)

My Home
Favorites
Previous Destinations
Point of Interest
Emergency
Street Address
Intersection

Note: If your vehicle is on a recognized road
and you do not press the Start Route
button, the system defaults to the Fastest
Route option and begins guidance.

City Center
Map

During route guidance, you can press the
talking bubble icon that appears in the
upper right navigation corner (green bar)
if you want the system to repeat route
guidance information. When the system
repeats the last guidance instruction, it
updates the distance to the next guidance
instruction, since it detects when the
vehicle is moving.

Edit Route Cancel Route
1.

Enter the necessary information into
the highlighted text fields (in any
order). For address destination entry,
the Go! button appears once you enter
all the necessary information. Pressing
the Go! button makes the address
location appear on the map. If you
choose Previous Destination, the last
20 destinations you have selected
appear.

411

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Point of Interest (POI) Categories

The system also allows you to sort
alphabetically, by distance or by cityseekr
listings (if available).

Main categories

cityseekr

Food/Drink & Dining

Note: cityseekr point of interest (POI)
information is limited to approximately 912
cities (881 in the United States, 20 in
Canada and 11 in Mexico).

Travel & Transportation
Financial
Emergency
Community
Health & Medicine
Automotive
Shopping
Entertainment & Arts

E142634

cityseekr, when available, is a service that
provides more information about certain
points of interest such as restaurants,
hotels and attractions.

Recreation & Sports
Government
Domestic Services

When you have selected a point of interest,
the location and information appear, such
as address and phone number. If cityseekr
lists the point of interest, more information
is available, such as a brief description,
check-in and checkout times or restaurant
hours.

Subcategories

Restaurant
Golf
Parking

Press More Information for a longer
review, a list of services and facilities, the
average room or meal price as well as the
website. This screen displays the point of
interest icon such as:

Home & Garden
Personal Care Services
Auto Dealership

Hotel

Govt Office
Public Transit
E143884

Education

Coffeehouse

To expand these listings, press the + in
front of the listing.

E142636

412

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Setting Your Navigation
Preferences

Food & Drink

Select settings for the system to take into
account when planning your route.

E142637

Nightlife

Press the Settings icon >
Settings > Navigation.
E142607

E142638

Map Preferences

Attraction

Breadcrumbs
Display your vehicle’s previously traveled
route with white dots. Turn this feature ON
or OFF.

E142639

This icon appears when your
selection exists in multiple
categories within the system.

Turn List Format

E142640

Have the system display your turn list Top
to Bottom or Bottom to Top.

When you are viewing more information
for hotels, cityseekr also tells you if the
hotel has certain services and facilities
using icons, such as:
• Restaurant
• Business center
• Handicap facilities
• Laundry
• Refrigerator
• 24 hour room service
• Fitness center
• Internet access
• Pool
• Wi-fi.

Parking POI Notification
Set the automatic parking point of interest
notification. Turn this feature ON or OFF.
When parking point of interest notification
is on, the icons display on the map when
you get close to your destination. This may
not be very useful in dense areas, and may
clutter the map when other points of
interest display.
Route Preferences
Preferred Route
Choose to have the system display the
Shortest, Fastest or most Ecological route
first. If you set Always Use Preferred
Route to Yes, the system uses the
selected route type to calculate only one
route to the desired destination.

For restaurants, cityseekr can provide
information such as star rating, average
cost, review, handicap access, hours of
operation, and website address.
For hotels, cityseekr can provide
information such as star rating, price
category, review, check-in and checkout
times, hotel service icons and website
address.

Always Use Preferred Route
Bypass route selection in destination
programming. The system only calculates
one route based on preferred route setting.

413

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Eco Time Penalty

Traffic Alert Notification

Select a low, medium or high cost for the
calculated Eco Route. The higher the
setting, the longer the time allotment is for
the route.

Have the system display traffic alert
notifications.
Other traffic alert features allows you to
turn on certain, or all, traffic icons on the
map such as road work, incident, accidents
and closed roads. Scroll down to view all
the different types of alerts. Turn these
features ON or OFF.

Avoid
These features allow you to choose to
have the system avoid freeways, toll roads,
ferries and car trains when planning your
route. Turn these features ON or OFF.

Avoid Areas
Choose areas which you want the system
to avoid when calculating a route for you.

Use HOV Lanes
Have the system use high-occupancy
vehicle lanes, if available, when planning
your route.

Press Add to program an entry. Once you
make a selection, the system tries to avoid
the area(s) if possible for all routes. To
delete a selection, choose the listing on
the screen. When the screen changes to
Avoid Areas Edit, you can press Delete
at the bottom right of the screen.

Navigation Preferences
Guidance Prompts
Have the system use Voice & Tones or
Tone Only on your programmed route.

Map Mode

Auto - Fill State/Province

Press the green bar in the upper right area
of the touchscreen to view map mode. Map
mode shows advanced viewing comprised
of both 2D city maps as well as 3D
landmarks (when available).

Have the system automatically fill in the
state and province based on the
information already entered into the
system. Turn this feature ON or OFF.

2D city maps show detailed outlines of
buildings, visible land use and land
elements and detailed railway
infrastructure for the most essential cities
around the globe. These maps also contain
features, such as town blocks, building
footprints, and railways.

Traffic Preferences
Avoid Traffic Problems
Choose how you want the system to
handle traffic problems along your route.
• Automatic: Have the system reroute
you to avoid traffic incidents that
develop and impact the current route.
The system does not provide a traffic
alert notification.
• Manual: Have the system always
provide a traffic alert notification for
traffic incidents along the planned
route. You have a choice to accept or
ignore the notification before making
the route deviation.

3D landmarks appear as clear, visible
objects that are typically recognizable and
have a certain tourist value. The 3D
landmarks appear in 3D map mode only.
Coverage varies, and improves with
updated map releases.

414

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Re-center the map by pressing
this icon whenever you scroll the
map away from your vehicle’s
current location.
E146188

Auto Zoom
Press the green bar to access map mode,
then select the + or - zoom button to bring
up the zoom level and Auto buttons on the
touchscreen. When you press Auto, Auto
Zoom turns on and Auto displays in the
bottom left corner of the screen in the map
scale. The map zoom level then
synchronizes with vehicle speed. The
slower your vehicle is traveling, the farther
in the map zooms in; the faster your vehicle
is traveling, the farther the map zooms out.
To turn the feature off, just press the + or
- button again.

E162051

Change the appearance of the map display
by repeatedly pressing the arrow button in
the upper left corner of the screen. It
toggles between three different map
modes: Heading up, North up, and 3D.
Heading up (2D map) always
shows the direction of forward
travel to be upward on the screen.
E142642
This view is available for map
scales up to 2.5 miles (4 kilometers). The
system remembers this setting for larger
map scales, but shows the map in North
up only. If the scale returns below this level,
the system restores Heading up.

E142643

In 3D mode, rotate the map view by
swiping your finger across the shaded bar
with the arrows.
Map Icons

North up (2D map) always shows
the northern direction to be
upward on the screen.

E142646

Scroll cursor allows you to scroll
the map; the fixed icon is in the
center of the screen. The map
E142647
position closest to the cursor is in
a window on the top center part of the
screen.

3D map mode provides an
elevated perspective of the map.
This viewing angle can be adjusted
E142644
and the map can be rotated 180
degrees by touching the map twice, and
then dragging your finger along the shaded
bar with arrows at the bottom of the map.

Address book entry default
icon(s) indicates the location on
the map of an address book entry.
E142648
This is the default symbol shown
after the entry has been stored to the
Address Book by any method other than
the map. You can select from any of the
22 icons available. You can use each icon
more than once.

View switches between full map, street
list and exit view in route guidance.
Menu displays a pop-up box that allows
direct access to navigation settings,
View/Edit Route, SIRIUS Travel Link,
Guidance Mute and Cancel Route.

415

F150 (TF6) , enUSA

Vehicle mark shows the current
location of your vehicle. It stays
in the center of the map display,
except when in scroll mode.

MyFord Touch™ (If Equipped)
Home indicates the location on
the map currently stored as the
home position. You can only save
E142649
one address from the Address
Book as your Home entry. You cannot
change this icon.

Set as Dest
Touch this button to select a scrolled
location on the map as your destination.
You may scroll the map by pressing your
index finger on the map display. When you
reach the desired location, simply let go
and then touch Set as Dest.

POI (Point Of Interest) icons
indicate locations of any point of
interest categories you choose to
E142650
display on the map. You can
choose to display three point of interest
categories on the map at one time.

Set as Waypoint
Touch this button to set the current
location as a waypoint.
Save to Favorites

Starting point indicates the
starting point of a planned route.

Touch this button to save the current
location to your favorites.

E142651

Waypoint indicates the location
of a waypoint on the map. The
number inside the circle is different
E142652
for each waypoint and represents
the position of the waypoint in the route
list.

POI Icons
Touch this button to select icons to display
on the map. You can select up to three
icons to display on the map at the same
time. Turn these ON or OFF.
Cancel Route

Destination symbol indicates the
ending point of a planned route.

Touch this button to cancel the active
route.

E142653

E142654

Next maneuver point indicates
the location of the next turn on the
planned route.

View/Edit Route
Access these features when a route is
active:
• View Route
• Edit Destination/Waypoints
• Edit Turn List
• Detour
• Edit Route Preferences
• Edit Traffic Preferences
• Cancel Route.

No GPS symbol indicates that
insufficient GPS satellite signals
are available for accurate map
E142655
positioning. This icon may display
under normal operation in an area with
poor GPS access.

Quick-touch Buttons
When in map mode, touch anywhere on
the map display to access the following
options:

416

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Nokia is the digital map provider for the
navigation application. If you find map data
errors, you may report them directly to
Nokia by going to
http://mapreporter.navteq.com. Nokia
evaluates all reported map errors and
responds with the result of their
investigation by e-mail.

Navigation system voice commands

"Destination POI"
"Destination POI category"
"Destination previous destination"
"Destination street address"

Navigation Map Updates

"Detour"

Annual navigation map updates are
available for purchase through your
dealership, by calling 1-800-NAVMAPS (in
Mexico, call 01-800-557-5539) or going
to www.navigation.com/ford. You need to
specify the make and model of your vehicle
to determine if there is an update available.

"Navigation"

"Navigation voice volume decrease"
"Navigation voice volume increase"
"Repeat instruction"

Navigation Voice Commands

"Show 3D"

When in navigation mode, press
the voice button on the steering
E142599
wheel controls. After the tone,
say any of the following commands:

"Show heading up"

Navigation system voice commands

"Show route"

"Cancel next waypoint"

"Show map"
"Show north up"

"Show turn list"

"Voice guidance off"

"Cancel route"

"Voice guidance on"

"Destination"

"Where am I?"

"Destination "

"Zoom in"

"Destination "
"Destination favorites"
"Destination home"
"Destination intersection"
"Destination nearest "
"Destination nearest POI"
"Destination play nametags"

417

F150 (TF6) , enUSA

MyFord Touch™ (If Equipped)
Navigation system voice commands

"NAVIGATION"

"Zoom out"

"Zoom maximum"

"Help"

"Zoom province"

These commands are only available when
a navigation route is active.

"Zoom state"

"Zoom street"

If you say "Destination", you can then say
any command in the following
"Destination" chart.

"Zoom to "
"Help"

If you say "Navigation", you can then say
any command in the following
"Navigation" chart.

If you say "Destination", you can then say
any command in the "Destination" chart.
One-shot Destination Street Address

"DESTINATION"

When you say either "Navigation
destination street address" or "Destination
street address", the system asks you to say
the full address. The system displays an
example on-screen. You can then speak
the address naturally, such as "One two
three four Main Street, Anytown".

""
""
"Favorites"
"Home"
"Intersection"
"Nearest "
"Nearest POI"
"Play nametags"
"POI category"
"Previous destination"
"Street address"
"Help"
"NAVIGATION"
*

"Destination"
"Zoom city"

"Zoom country"
"Zoom minimum"

418

F150 (TF6) , enUSA

Accessories
Lifestyle

For a complete listing of the accessories
that are available for your vehicle, please
contact an authorized dealer or visit our
online store at
www.Accessories.Ford.com (United
States only).

•
•
•
•
•
•
•

Ford Motor Company will repair or replace
any properly authorized dealer-installed
Ford Custom Accessories found to be
defective in factory-supplied materials or
workmanship during the warranty period,
as well as any component damaged by the
defective accessories.
Ford Motor Company will warrant your
vehicle through the warranty that provides
the greatest benefit:
• 24 months, unlimited mileage.
• The remainder of your new vehicle
limited warranty.

•
•
•
•
•
•
•

Contact an authorized dealer for details
and a copy of the warranty.

•

Exterior style
•
•
•
•
•
•
•
•
•

Peace of mind

Hood deflector.
Chrome exhaust tips.
Side window deflectors.
Front grilles.
Running boards.
Step bars.
Splash guards.
Lamps
Custom graphics*.

•
•
•
•
•
•
•
•
•
•
•
•
•
•

Interior style
•
•
•
•
•

Ambient lighting.
Floor mats.
Electrochromatic
compass/temperature interior mirrors.
Sliding rear windows.
Leather-trimmed interior seating*.

419

F150 (TF6) , enUSA

Smoker's package.
Bedliners and bedmats.
Bed side step.
Towing mirrors.
Bed extender.
Tonneau covers*.
Interior cargo organization and
management.
Racks and carriers*.
Truck bed camping tent*.
Sportliner cargo liner*.
Rear-seat entertainment*.
Trailer brake controller.
Hitch balls and towbars.
Truck bed cargo organization and
management.
Trailer hitches, wiring harnesses and
accessories.

Keyless entry keypad.
Vehicle security systems.
Protective seat covers*.
Cable lock*.
Locking gas plug for capless fuel
system.
Bumper- and hitch-mounted parking
sensors*.
Remote start.
Wheel locks.
Wheel well liners.
Bed hooks*.
Back-up alarm*.
Tool or cargo boxes*.
Speed/Cruise control.
Vehicle cover.

Accessories
*The accessory manufacturer designs,
develops and therefore warrants Ford
Licensed Accessories, and does not design
or test these accessories to Ford Motor
Company engineering requirements.
Contact an authorized Ford dealer for the
manufacturer's limited warranty details,
and request a copy of the Ford Licensed
Accessories product limited warranty from
the accessory manufacturer.

•

For maximum vehicle performance, keep
the following information in mind when
adding accessories or equipment to your
vehicle:
• When adding accessories, equipment,
passengers and luggage to your
vehicle, do not exceed the total weight
capacity of the vehicle or of the front
or rear axle (GVWR or GAWR as
indicated on the Safety Compliance
Certification label). Ask an authorized
dealer for specific weight information.
• The Federal Communications
Commission (FCC) and Canadian
Radio Telecommunications
Commission (CRTC) regulate the use
of mobile communications systems
that are equipped with radio
transmitters, for example, two-way
radios, telephones and theft alarms.
Any such equipment installed in your
vehicle should comply with Federal
Communications Commission (FCC)
and Canadian Radio
Telecommunications Commission
(CRTC) regulations and should be
installed only by an authorized dealer.

420

F150 (TF6) , enUSA

Mobile communications systems may
harm the operation of your vehicle,
particularly if their manufacturer did
not design them specifically for
automotive use.
If you or an authorized Ford dealer add
any non-Ford electrical or electronic
accessories or components to your
vehicle, you may adversely affect
battery performance and durability,
and may adversely affect the
performance of other electrical
systems in the vehicle.

Appendices
•

END USER LICENSE
AGREEMENT
SYNC® End User License
Agreement (EULA)
•

•

You have acquired a device ("DEVICE")
that includes software licensed by Ford
Motor Company and its affiliates
("FORD MOTOR COMPANY") from an
affiliate of Microsoft Corporation
("MS") . Those installed software
products of MS origin, as well as
associated media, printed materials,
and "online" or electronic
documentation ("MS SOFTWARE")
are protected by international
intellectual property laws and treaties.
The MS SOFTWARE is licensed, not
sold. All rights reserved.
The MS SOFTWARE may interface with
and/or communicate with, or may be
later upgraded to interface with and/or
communicate with additional software
and/or systems provided by FORD
MOTOR COMPANY. The additional
software and systems of FORD
MOTOR COMPANY origin, as well as
associated media, printed materials,
and "online" or electronic
documentation ("FORD SOFTWARE")
are protected by international
intellectual property laws and treaties.
The FORD SOFTWARE is licensed, not
sold. All rights reserved.

•

IF YOU DO NOT AGREE TO THIS END
USER LICENSE AGREEMENT ("EULA")
DO NOT USE THE DEVICE OR COPY
THE SOFTWARE. ANY USE OF THE
SOFTWARE, INCLUDING BUT NOT
LIMITED TO USE ON THE DEVICE, WILL
CONSTITUTE YOUR AGREEMENT TO
THIS EULA (OR RATIFICATION OF ANY
PREVIOUS CONSENT).
GRANT OF SOFTWARE LICENSE: This
EULA grants you the following license:
•

421

F150 (TF6) , enUSA

The MS SOFTWARE and/or FORD
SOFTWARE may interface with and/or
communicate with, or may be later
upgraded to interface with and/or
communicate with additional software
and/or systems provided by third party
software and service suppliers. The
additional software and services of
third party origin, as well as associated
media, printed materials, and "online"
or electronic documentation ("THIRD
PARTY SOFTWARE") are protected by
international intellectual property laws
and treaties. The THIRD PARTY
SOFTWARE is licensed, not sold. All
rights reserved.
The MS SOFTWARE, FORD
SOFTWARE and THIRD PARTY
SOFTWARE hereinafter collectively
and individually will be referred to as
"SOFTWARE".

You may use the SOFTWARE as
installed on the DEVICE and as
otherwise interfacing with systems
and/or services provide by or through
FORD MOTOR COMPANY or its third
party software and service providers.

Appendices
•

Description of Other Rights and
Limitations
•

•

Speech Recognition: If the
SOFTWARE includes speech
recognition component(s), you should
understand that speech recognition is
an inherently statistical process and
that recognition errors are inherent in
the process. Neither FORD MOTOR
COMPANY nor its suppliers shall be
liable for any damages arising out of
errors in the speech recognition
process.
Limitations on Reverse Engineering,
Decompilation and Disassembly:
You may not reverse engineer,
decompile, or disassemble nor permit
others to reverse engineer, decompile
or disassemble the SOFTWARE, except
and only to the extent that such activity
is expressly permitted by applicable
law notwithstanding this limitation.
Limitations on Distributing,
Copying, Modifying and Creating
Derivative Works: You may not
distribute, copy, make modifications
to or create derivative works based on
the SOFTWARE, except and only to the
extent that such activity is expressly
permitted by applicable law
notwithstanding this limitation.
Single EULA: The end user
documentation for the DEVICE and
related systems and services may
contain multiple EULAs, such as
multiple translations and/or multiple
media versions (e.g., in the user
documentation and in the software).
Even if you receive multiple EULAs, you
are licensed to use only one (1) copy of
the SOFTWARE.

•

422

F150 (TF6) , enUSA

SOFTWARE Transfer: You may
permanently transfer your rights under
this EULA only as part of a sale or
transfer of the DEVICE, provided you
retain no copies, you transfer all of the
SOFTWARE (including all component
parts, the media and printed materials,
any upgrades, and, if applicable, the
Certificate(s) of Authenticity), and the
recipient agrees to the terms of this
EULA. If the SOFTWARE is an upgrade,
any transfer must include all prior
versions of the SOFTWARE.
Termination: Without prejudice to any
other rights, FORD MOTOR COMPANY
or MS may terminate this EULA if you
fail to comply with the terms and
conditions of this EULA.
Security Updates/Digital Rights
Management: Content owners use
the WMDRM technology included in
your DEVICE to protect their
intellectual property, included
copyrighted content. Portions of the
SOFTWARE on your DEVICE use
WMDRM software to access
WMDRM-protected content. If the
WMDRM software fails to protect the
content, content owners may ask
Microsoft to revoke the SOFTWARE's
ability to use WMDRM to play or copy
protected content. This action does
not affect unprotected content. When
your DEVICE downloads licenses for
protected content, you agree that
Microsoft may include a revocation list
with the licenses. Content owners may
require you to upgrade the SOFTWARE
on your DEVICE to access their content.
If you decline an upgrade, you will not
be able to access content that requires
the upgrade.

Appendices
•

•

supplements, add-on components, or
Internet-based services components
of the SOFTWARE after the date you
obtain your initial copy of the
SOFTWARE ("Supplemental
Components").

Consent to Use of Data: You agree
that MS, Microsoft Corporation, FORD
MOTOR COMPANY, third party
software and systems suppliers, their
affiliates and/or their designated agent
may collect and use technical
information gathered in any manner as
part of product support services related
to the SOFTWARE or related services.
MS, Microsoft Corporation, FORD
MOTOR COMPANY, third party
software and services suppliers, their
affiliates and/or their designated agent
may use this information solely to
improve their products or to provide
customized services or technologies to
you. MS, Microsoft Corporation, FORD
MOTOR COMPANY, third party
software and systems suppliers, their
affiliates and/or their designated agent
may disclose this information to others,
but not in a form that personally
identifies you.
Internet-Based Services
Components: The SOFTWARE may
contain components that enable and
facilitate the use of certain
Internet-based services. You
acknowledge and agree that MS,
Microsoft Corporation, FORD MOTOR
COMPANY, third party software and
service suppliers, their affiliates and/or
their designated agent may
automatically check the version of the
SOFTWARE and/or its components
that you are utilizing and may provide
upgrades or supplements to the
SOFTWARE that may be automatically
downloaded to your DEVICE.
Additional Software/Services: The
SOFTWARE may permit FORD MOTOR
COMPANY, third party software and
service suppliers, MS, Microsoft
Corporation, their affiliates and/or their
designated agent to provide or make
available to you SOFTWARE updates,

If FORD MOTOR COMPANY or third party
software and services suppliers provide or
make available to you Supplemental
Components and no other EULA terms are
provided along with the Supplemental
Components, then the terms of this EULA
shall apply.
If MS, Microsoft Corporation, their affiliates
and/or their designated agent make
available Supplemental Components, and
no other EULA terms are provided, then
the terms of this EULA shall apply, except
that the MS, Microsoft Corporation or
affiliate entity providing the Supplemental
Component(s) shall be the licensor of the
Supplemental Component(s).
FORD MOTOR COMPANY, MS, Microsoft
Corporation, their affiliates and/or their
designated agent reserve the right to
discontinue without liability any
Internet-based services provided to you or
made available to you through the use of
the SOFTWARE.

423

F150 (TF6) , enUSA

Appendices
•

•

Links to Third Party Sites: The MS
SOFTWARE may provide you with the
ability to link to third party sites through
the use of the SOFTWARE. The third
party sites are not under the control of
MS, Microsoft Corporation, their
affiliates and/or their designated
agent. Neither MS nor Microsoft
Corporation nor their affiliates nor their
designated agent are responsible for
(i) the contents of any third party sites,
any links contained in third party sites,
or any changes or updates to third
party sites, or (ii) webcasting or any
other form of transmission received
from any third party sites. If the
SOFTWARE provides links to third
party sites, those links are provided to
you only as a convenience, and the
inclusion of any link does not imply an
endorsement of the third party site by
MS, Microsoft Corporation, their
affiliates and/or their designated
agent.
Obligation to Drive Responsibly:
You recognize your obligation to drive
responsibly and keep attention on the
road. You will read and abide with the
DEVICE operating instructions
particularly as they pertain to safety
and assumes any risk associated with
the use of the DEVICE.

INTELLECTUAL PROPERTY RIGHTS:
All title and intellectual property rights in
and to the SOFTWARE (including but not
limited to any images, photographs,
animations, video, audio, music, text and
"applets" incorporated into the
SOFTWARE), the accompanying printed
materials, and any copies of the
SOFTWARE, are owned by MS, Microsoft
Corporation, FORD MOTOR COMPANY, or
their affiliates or suppliers. The
SOFTWARE is licensed, not sold. You may
not copy the printed materials
accompanying the SOFTWARE. All title
and intellectual property rights in and to
the content which may be accessed
through use of the SOFTWARE is the
property of the respective content owner
and may be protected by applicable
copyright or other intellectual property
laws and treaties. This EULA grants you no
rights to use such content. All rights not
specifically granted under this EULA are
reserved by MS, Microsoft Corporation,
FORD MOTOR COMPANY, third party
software and service providers, their
affiliates and suppliers. Use of any on-line
services which may be accessed through
the SOFTWARE may be governed by the
respective terms of use relating to such
services. If this SOFTWARE contains
documentation that is provided only in
electronic form, you may print one copy of
such electronic documentation.

UPGRADES AND RECOVERY MEDIA:
If the SOFTWARE is provided by FORD
MOTOR COMPANY separate from the
DEVICE on media such as a ROM chip, CD
ROM disk(s) or via web download or other
means, and is labeled "For Upgrade
Purposes Only" or "For Recovery Purposes
Only" you may install one (1) copy of such
SOFTWARE onto the DEVICE as a
replacement copy for the existing
SOFTWARE, and use it in accordance with
this EULA, including any additional EULA
terms accompanying the upgrade
SOFTWARE.

EXPORT RESTRICTIONS: You
acknowledge that the SOFTWARE is
subject to U.S. and European Union export
jurisdiction. You agree to comply with all
applicable international and national laws
that apply to the SOFTWARE, including
the U.S. Export Administration Regulations,
as well as end-user, end-use and
destination restrictions issued by U.S. and
other governments. For additional
information, see
http://www.microsoft.com/exporting/.

424

F150 (TF6) , enUSA

Appendices
Adobe

TRADEMARKS: This EULA does not grant
you any rights in connection with any
trademarks or service marks of FORD
MOTOR COMPANY, MS, Microsoft
Corporation, third party software or service
providers, their affiliates or suppliers.

Contains Adobe® [Flash® Player] or
[AIR®] technology by Adobe Systems
Incorporated. This [Licensee Product]
contains [Adobe® Flash® Player]
[Adobe® AIR®] software under license
from Adobe Systems Incorporated,
Copyright ©1995-2009 Adobe
Macromedia Software LLC. All rights
reserved. Adobe, Flash and AIR are
trademarks of Adobe Systems
Incorporated.

PRODUCT SUPPORT: Product support
for the SOFTWARE is not provided by MS,
its parent corporation Microsoft
Corporation, or their affiliates or
subsidiaries. For product support, please
refer to FORD MOTOR COMPANY
instructions provided in the documentation
for the DEVICE. Should you have any
questions concerning this EULA, or if you
desire to contact FORD MOTOR
COMPANY for any other reason, please
refer to the address provided in the
documentation for the DEVICE.

End User Notice
Microsoft® Windows® Mobile for
Automotive Important Safety
Information
This system Ford SYNC™ contains
software that is licensed to Manufacturer
FORD MOTOR COMPANY by an affiliate
of Microsoft Corporation pursuant to a
license agreement. Any removal,
reproduction, reverse engineering or other
unauthorized use of the software from this
system in violation of the license
agreement is strictly prohibited and may
subject you to legal action.

No Liability for Certain Damages:
EXCEPT AS PROHIBITED BY LAW, FORD
MOTOR COMPANY, ANY THIRD PARTY
SOFTWARE OR SERVICES SUPPLIERS,
MS, MICROSOFT CORPORATION AND
THEIR AFFILIATES SHALL HAVE NO
LIABILITY FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL OR INCIDENTAL
DAMAGES ARISING FROM OR IN
CONNECTION WITH THE USE OR
PERFORMANCE OF THE SOFTWARE. THIS
LIMITATION SHALL APPLY EVEN IF ANY
REMEDY FAILS OF ITS ESSENTIAL
PURPOSE. IN NO EVENT SHALL MS,
MICROSOFT CORPORATION AND/OR
THEIR AFFILIATES BE LIABLE FOR ANY
AMOUNT IN EXCESS OF U.S. TWO
HUNDRED FIFTY DOLLARS (U.S.
$250.00).
•

Read and follow instructions: Before
using your Windows Automotive- based
system, read and follow all instructions
and safety information provided in this end
user manual ("User's Guide"). Not
following precautions found in this User's
Guide can lead to an accident or other
serious consequences.
Keep User's Guide in vehicle: When kept
in the vehicle, the User's Guide will be a
ready reference for you and other users
unfamiliar with the Windows
Automotive-based system. Please make
certain that before using the system for
the first time, all persons have access to
the User's Guide and read its instructions
and safety information carefully.

THERE ARE NO WARRANTIES OTHER
THAN THOSE THAT MAY EXPRESSLY
BE PROVIDED FOR YOUR NEW
VEHICLE.

425

F150 (TF6) , enUSA

Appendices
Use of Speech Recognition Functions:
Speech recognition software is inherently
a statistical process which is subject to
errors. It is your responsibility to monitor
any speech recognition functions included
in the system and address any errors.

WARNING
Operating certain parts of this
system while driving can distract
your attention away from the road,
and possibly cause an accident or other
serious consequences. Do not change
system settings or enter data non-verbally
(using your hands) while driving. Stop the
vehicle in a safe and legal manner before
attempting these operations. This is
important since while setting up or
changing some functions you might be
required to distract your attention away
from the road and remove your hands from
the wheel.

Navigation Features: Any navigation
features included in the system are
intended to provide turn by turn
instructions to get you to a desired
destination. Please make certain all
persons using this system carefully read
and follow instructions and safety
information fully.
Distraction Hazard: Any navigation
features may require manual (non-verbal)
setup. Attempting to perform such set-up
or insert data while driving can seriously
distract your attention and could cause an
accident or other serious consequences.
Stop the vehicle in a safe and legal manner
before attempting these operations.

General Operation
Voice Command Control: Functions
within the Windows Automotive-based
system may be accomplished using only
voice commands. Using voice commands
while driving allows you to operate the
system without removing your hands from
the wheel.

Let Your Judgment Prevail: Any
navigation features are provided only as
an aid. Make your driving decisions based
on your observations of local conditions
and existing traffic regulations. Any such
feature is not a substitute for your personal
judgment. Any route suggestions made by
this system should never replace any local
traffic regulations or your personal
judgment or knowledge of safe driving
practices.

Prolonged Views of Screen: Do not
access any function requiring a prolonged
view of the screen while you are driving.
Pull over in a safe and legal manner before
attempting to access a function of the
system requiring prolonged attention. Even
occasional short scans to the screen may
be hazardous if your attention has been
diverted away from your driving task at a
critical time.

Route Safety: Do not follow the route
suggestions if doing so would result in an
unsafe or illegal maneuver, if you would be
placed in an unsafe situation, or if you
would be directed into an area that you
consider unsafe. The driver is ultimately
responsible for the safe operation of the
vehicle and therefore, must evaluate
whether it is safe to follow the suggested
directions.

Volume Setting: Do not raise the volume
excessively. Keep the volume at a level
where you can still hear outside traffic and
emergency signals while driving. Driving
while unable to hear these sounds could
cause an accident.

426

F150 (TF6) , enUSA

Appendices
Potential Map Inaccuracy: Maps used
by this system may be inaccurate because
of changes in roads, traffic controls or
driving conditions. Always use good
judgment and common sense when
following the suggested routes.

Telenav may revise this Agreement and
the privacy policy at any time, with or
without notice to you. You agree to visit
http://www.telenav.com from time to time
to review the then current version of this
Agreement and of the privacy policy.

Emergency Services: Do not rely on any
navigation features included in the system
to route you to emergency services. Ask
local authorities or an emergency services
operator for these locations. Not all
emergency services such as police, fire
stations, hospitals and clinics are likely to
be contained in the map database for such
navigation features.

1. Safe and Lawful Use
You acknowledge that devoting attention
to the Telenav Software may pose a risk
of injury or death to you and others in
situations that otherwise require your
undivided attention, and you therefore
agree to comply with the following when
using the Telenav Software: (a) observe
all traffic laws and otherwise drive safely;
(b) use your own personal judgment while
driving. If you feel that a route suggested
by the Telenav Software instructs you to
perform an unsafe or illegal maneuver,
places you in an unsafe situation, or directs
you into an area that you consider to be
unsafe, do not follow such instructions; (c)
do not input destinations, or otherwise
manipulate the Telenav Software, unless
your vehicle is stationary and parked; (d)
do not use the Telenav Software for any
illegal, unauthorized, unintended, unsafe,
hazardous, or unlawful purposes, or in any
manner inconsistent with this Agreement;
(e) arrange all GPS and wireless devices
and cables necessary for use of the
Telenav Software in a secure manner in
your vehicle so that they will not interfere
with your driving and will not prevent the
operation of any safety device (such as an
airbag).

TeleNav Software End User License
Agreement
Please read these terms and conditions
carefully before you use the Telenav
Software. Your use of the Telenav
Software indicates that you accept these
terms and conditions. If you do not accept
these terms and conditions, do not break
the seal of the package, launch, or
otherwise use the Telenav Software.
These terms and conditions represent the
agreement (“Agreement”) between you
and Telenav, Inc. (“Telenav”) with respect
to the Telenav Software (including
upgrades, modifications, or additions
thereto) (collectively “Telenav Software”).
All references herein to “you” and “your”
means you, your employees, agents, and
contractors, and any other entity on whose
behalf you accept these terms and
conditions, all of whom shall also be bound
by this Agreement. Additionally, all of your
account information, as well as other
payment and personal information
provided by you to Telenav (directly or
through the use of the Telenav Software,
is subject to Telenav’s privacy policy
located at http://www.telenav.com.

You agree to indemnify and hold Telenav
harmless against all claims resulting from
any dangerous or otherwise inappropriate
use of the Telenav Software in any moving
vehicle, including as a result of your failure
to comply with the directions above.

427

F150 (TF6) , enUSA

Appendices
2. Account Information

or proprietary rights, rights of publicity or
privacy or other rights of any party, (ii)
violates any law, statute, ordinance or
regulation, including but not limited to laws
and regulations related to spamming,
privacy, consumer and child protection,
obscenity or defamation, or (iii) is harmful,
threatening, abusive, harassing, tortuous,
defamatory, vulgar, obscene, libelous, or
otherwise objectionable; and (f) lease, rent
out, or otherwise permit unauthorized
access by third parties to the Telenav
Software without advanced written
permission of Telenav.

You agree: (a) when registering the
Telenav Software, to provide Telenav with
true, accurate, current, and complete
information about yourself, and (b) to
inform Telenav promptly of any changes
to such information, and to keep it true,
accurate, current and complete.
3. Software License
Subject to your compliance with the terms
of this Agreement, Telenav hereby grants
to you a personal, non-exclusive,
non-transferable license (except as
expressly permitted below in connection
with your permanent transfer of the
Telenav Software license), without the
right to sublicense, to use the Telenav
Software (in object code form only) in
order to access and use the Telenav
Software. This license shall terminate upon
any termination or expiration of this
Agreement. You agree that you will use the
Telenav Software only for your personal
business or leisure purposes, and not to
provide commercial navigation services to
other parties.

4. Disclaimers
To the fullest extent permissible pursuant
to applicable law, in no event will Telenav,
its licensors and suppliers, or agents or
employees of any of the foregoing, be
liable for any decision made or action
taken by you or anyone else in reliance on
the information provided by the Telenav
Software. Telenav also does not warrant
the accuracy of the map or other data used
for the Telenav Software. Such data may
not always reflect reality due to, among
other things, road closures, construction,
weather, new roads and other changing
conditions. You are responsible for the
entire risk arising out of your use of the
Telenav Software. For example but
without limitation, you agree not to rely on
the Telenav Software for critical navigation
in areas where the well-being or survival
of you or others is dependent on the
accuracy of navigation, as the maps or
functionality of the Telenav Software are
not intended to support such high risk
applications, especially in more remote
geographical areas.

3.1 License Limitations
You agree not to do any of the following:
(a) reverse engineer, decompile,
disassemble, translate, modify, alter or
otherwise change the Telenav Software
or any part thereof; (b) attempt to derive
the source code, audio library or structure
of the Telenav Software without the prior
express written consent of Telenav; (c)
remove from the Telenav Software, or
alter, any of Telenav’s or its suppliers’
trademarks, trade names, logos, patent or
copyright notices, or other notices or
markings; (d) distribute, sublicense or
otherwise transfer the Telenav Software
to others, except as part of your permanent
transfer of the Telenav Software; or (e)
use the Telenav Software in any manner
that (i) infringes the intellectual property

TELENAV EXPRESSLY DISCLAIMS AND
EXCLUDES ALL WARRANTIES IN
CONNECTION WITH THE TELENAV
SOFTWARE, WHETHER STATUTORY,
EXPRESS OR IMPLIED, INCLUDING ALL
WARRANTIES WHICH MAY ARISE FROM

428

F150 (TF6) , enUSA

Appendices
COURSE OF DEALING, CUSTOM OR
TRADE AND INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND
NON-INFRINGEMENT OF THIRD PARTY
RIGHTS WITH RESPECT TO THE TELENAV
SOFTWARE. Certain jurisdictions do not
permit the disclaimer of certain warranties,
so this limitation may not apply to you.

STATES AND/OR JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO
YOU.
6. Arbitration and Governing Law
You agree that any dispute, claim or
controversy arising out of or relating to this
Agreement or the Telenav Software shall
be settled by independent arbitration
involving a neutral arbitrator and
administered by the American Arbitration
Association in the County of Santa Clara,
California. The arbitrator shall apply the
Commercial Arbitration Rules of the
American Arbitration Association, and the
judgment upon the award rendered by the
arbitrator may be entered by any court
having jurisdiction. Note that there is no
judge or jury in an arbitration proceeding
and the decision of the arbitrator shall be
binding upon both parties. You expressly
agree to waive your right to a jury trial.

5. Limitation of Liability
TO THE EXTENT PERMITTED UNDER
APPLICABLE LAW, UNDER NO
CIRCUMSTANCES SHALL TELENAV OR
ITS LICENSORS AND SUPPLIERS BE
LIABLE TO YOU OR TO ANY THIRD PARTY
FOR ANY INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR
EXEMPLARY DAMAGES (INCLUDING IN
EACH CASE, BUT NOT LIMITED TO,
DAMAGES FOR THE INABILITY TO USE
THE EQUIPMENT OR ACCESS DATA,
LOSS OF DATA, LOSS OF BUSINESS,
LOSS OF PROFITS, BUSINESS
INTERRUPTION OR THE LIKE) ARISING
OUT OF THE USE OF OR INABILITY TO
USE THE TELENAV SOFTWARE, EVEN IF
TELENAV HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.

This Agreement and performance
hereunder will be governed by and
construed in accordance with the laws of
the State of California, without giving
effect to its conflict of laws provisions. To
the extent judicial action is necessary in
connection with the binding arbitration,
both Telenav and you agree to submit to
the exclusive jurisdiction of the courts of
the County of Santa Clara, California. The
United Nations Convention on Contracts
for the International Sale of Goods shall
not apply.

NOTWITHSTANDING ANY DAMAGES
THAT YOU MIGHT INCUR FOR ANY
REASON WHATSOEVER (INCLUDING,
WITHOUT LIMITATION, ALL DAMAGES
REFERENCED HEREIN AND ALL DIRECT
OR GENERAL DAMAGES IN CONTRACT,
TORT (INCLUDING NEGLIGENCE) OR
OTHERWISE), THE ENTIRE LIABILITY OF
TELENAV AND OF ALL OF TELENAV’S
SUPPLIERS SHALL BE LIMITED TO THE
AMOUNT ACTUALLY PAID BY YOU FOR
THE TELENAV SOFTWARE. SOME

7. Assignment
You may not resell, assign, or transfer this
Agreement or any of your rights or
obligations, except in totality, in connection
with your permanent transfer of the
Telenav Software, and expressly
conditioned upon the new user of the
Telenav Software agreeing to be bound by
429

F150 (TF6) , enUSA

Appendices
the terms and conditions of this
Agreement. Any such sale, assignment or
transfer that is not expressly permitted
under this paragraph will result in
immediate termination of this Agreement,
without liability to Telenav, in which case
you and all other parties shall immediately
cease all use of the Telenav Software.
Notwithstanding the foregoing, Telenav
may assign this Agreement to any other
party at any time without notice, provided
the assignee remains bound by this
Agreement.

Notices by posting them on Telenav’s
Website or by downloading such Notices
to your wireless device. If you desire to
withdraw your consent to receive Notices
electronically, you must discontinue your
use of the Telenav Software.
8.4
Telenav’s or your failure to require
performance of any provision shall not
affect that party’s right to require
performance at any time thereafter, nor
shall a waiver of any breach or default of
this Agreement constitute a waiver of any
subsequent breach or default or a waiver
of the provision itself.

8. Miscellaneous
8.1
This Agreement constitutes the entire
agreement between Telenav and you with
respect to the subject matter hereof.

8.5
If any provision herein is held
unenforceable, then such provision will be
modified to reflect the intention of the
parties, and the remaining provisions of
this Agreement will remain in full force and
effect.

8.2
Except for the limited licenses expressly
granted in this Agreement, Telenav retains
all right, title and interest in and to the
Telenav Software, including without
limitation all related intellectual property
rights. No licenses or other rights which are
not expressly granted in this Agreement
are intended to, or shall be, granted or
conferred by implication, statute,
inducement, estoppel or otherwise, and
Telenav and its suppliers and licensors
hereby reserve all of their respective rights
other than the licenses explicitly granted
in this Agreement.

8.6
The headings in this Agreement are for
convenience of reference only, will not be
deemed to be a part of this Agreement,
and will not be referred to in connection
with the construction or interpretation of
this Agreement. As used in this Agreement,
the words “include” and “including,” and
variations thereof, will not be deemed to
be terms of limitation, but rather will be
deemed to be followed by the words
“without limitation”.

8.3
By using the Telenav Software, you
consent to receive from Telenav all
communications, including notices,
agreements, legally required disclosures
or other information in connection with the
Telenav Software (collectively, “Notices”)
electronically. Telenav may provide such

9. Other Vendors Terms and Conditions
The Telenav Software utilizes map and
other data licensed to Telenav by third
party vendors for the benefit of you and
other end users. This Agreement includes
end-user terms applicable to these
companies (included at the end of this

430

F150 (TF6) , enUSA

Appendices
Agreement), and thus your use of the
Telenav Software is also subject to such
terms. You agree to comply with the
following additional terms and conditions,
which are applicable to Telenav’s third
party vendor licensors:

TERMS AND CONDITIONS
License Limitations on Use:
You agree that your license to use this Data
is limited to and conditioned on use for
solely personal, noncommercial purposes,
and not for service bureau, timesharing or
other similar purposes. Except as otherwise
set forth herein, you agree not to otherwise
reproduce, copy, modify, decompile,
disassemble or reverse engineer any
portion of this Data, and may not transfer
or distribute it in any form, for any purpose,
except to the extent permitted by
mandatory laws.

End User License Agreement For
Distribution By HERE For North
America/APAC
The content provided (“Data”) is licensed,
not sold. By opening this package, or
installing, copying, or otherwise using the
Data, you agree to be bound by the terms
of this agreement. If you do not agree to
the terms of this agreement, you are not
permitted to install, copy, use, resell or
transfer the Data. If you wish to reject the
terms of this agreement, and have not
installed, copied, or used the Data, you
must contact your retailer or HERE North
America, LLC (as defined below) within
thirty (30) days of purchase for a refund
of your purchase price. To contact HERE,
please visit www.here.com.

License Limitations on Transfer:
Your limited license does not allow transfer
or resale of the Data, except on the
condition that you may transfer the Data
and all accompanying materials on a
permanent basis if: (a) you retain no copies
of the Data; (b) the recipient agrees to the
terms of this End-User License Agreement;
and (c) you transfer the Data in the exact
same form as you purchased it by
physically transferring the original media
(e.g., the CD-ROM or DVD you purchased),
all original packaging, all Manuals and
other documentation. Specifically,
Multi-disc sets may only be transferred or
sold as a complete set as provided to you
and not as a subset thereof.

The Data is provided for your personal,
internal use only and may not be resold. It
is protected by copyright, and is subject to
the following terms (this “End User License
Agreement”) and conditions which are
agreed to by you, on the one hand, and
HERE and its licensors (including their
licensors and suppliers) on the other hand.
For purposes of these terms, “HERE” shall
mean (a) HERE North America, LLC with
respect to Data for the Americas and/or
the Asia Pacific region and (b) HERE
Europe B.V. for Data for Europe, the Middle
East and/or Africa.

Additional License Limitations:
Except where you have been specifically
licensed to do so by HERE in a separate
written agreement, and without limiting
the preceding paragraph, your license is
conditioned on use of the Data as
prescribed in this agreement, and you may
not (a) use this Data with any products,
systems, or applications installed or
otherwise connected to or in
communication with vehicles capable of
vehicle navigation, positioning, dispatch,

The Data includes certain information and
related content provided under license to
HERE from third parties and is subject to
the applicable supplier terms and
copyright notices set forth at the following
URL:
http://corporate.navteq.com/supplier_terms.html.

431

F150 (TF6) , enUSA

Appendices
Disclaimer of Liability:

real time route guidance, fleet
management or similar applications; or (b)
with, or in communication with, including
without limitation, cellular phones,
palmtop and handheld computers, pagers,
and personal digital -assistants or PDAs.

This Data is provided to you “as is”, and
you agree to use it at your own risk. HERE
and its licensors (and their licensors and
suppliers) make no guarantees,
representations or warranties of any kind,
express or implied, arising by law or
otherwise, including but not limited to,
content, quality, accuracy, completeness,
effectiveness, reliability, fitness for a
particular purpose, usefulness, use or
results to be obtained from this Data, or
that the Data or server will be
uninterrupted or error ¬free.

HERE AND ITS LICENSORS (INCLUDING
THEIR LICENSORS AND SUPPLIERS)
SHALL NOT BE LIABLE TO YOU IN
RESPECT OF ANY CLAIM, DEMAND OR
ACTION, IRRESPECTIVE OF THE NATURE
OF THE CAUSE OF THE CLAIM, DEMAND
OR ACTION ALLEGING ANY LOSS, INJURY
OR DAMAGES, DIRECT OR INDIRECT,
WHICH MAY RESULT FROM THE USE OR
POSSESSION OF THIS DATA; OR FOR ANY
LOSS OF PROFIT, REVENUE, CONTRACTS
OR SAVINGS, OR ANY OTHER DIRECT,
INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES ARISING
OUT OF YOUR USE OF OR INABILITY TO
USE THIS DATA, ANY DEFECT IN THIS
DATA, OR THE BREACH OF THESE TERMS
OR CONDITIONS, WHETHER IN AN
ACTION IN CONTRACT OR TORT OR
BASED ON A WARRANTY, EVEN IF HERE
OR ITS LICENSORS HAVE BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
Some States, Territories and Countries do
not allow certain liability exclusions or
damages limitations, so to that extent the
above may not apply to you.

Disclaimer of Warranty:

Export Control:

HERE AND ITS LICENSORS (INCLUDING
THEIR LICENSORS AND SUPPLIERS)
DISCLAIM ANY WARRANTIES, EXPRESS
OR IMPLIED, OF QUALITY,
PERFORMANCE, MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE
OR NON-INFRINGEMENT. Some States,
Territories and Countries do not allow
certain warranty exclusions, so to that
extent the above exclusion may not apply
to you.

You agree not to export from anywhere
any part of the Data or any direct product
thereof except in compliance with, and
with all licenses and approvals required
under, applicable export laws, rules and
regulations, including but not limited to the
laws, rules and regulations administered
by the Office of Foreign Assets Control of
the U.S. Department of Commerce and the
Bureau of Industry and Security of the U.S.
Department of Commerce. To the extent
that any such export laws, rules or
regulations prohibit HERE from complying
with any of its obligations hereunder to
deliver or distribute Data, such failure shall
be excused and shall not constitute a
breach of this Agreement.

Note: This Data may contain inaccurate or
incomplete information due to the passage
of time, changing circum-stances, sources
used and the nature of collecting
comprehensive geographic Data, any of
which may lead to incorrect results.
No Warranty:

432

F150 (TF6) , enUSA

Appendices
Entire Agreement:

Government End Users:

These terms and conditions constitute the
entire agreement between HERE (and its
licensors, including their licensors and
suppliers) and you pertaining to the subject
matter hereof, and supersedes in their
entirety any and all written or oral
agreements previously existing between
us with respect to such subject matter.

If the Data is being acquired by or on behalf
of the United States government or any
other entity seeking or applying rights
similar to those customarily claimed by the
United States government, this Data is a
“commercial item” as that term is defined
at 48 C.F.R. (“FAR”) 2.101, is licensed in
accordance with this End¬ User License
Agreement, and each copy of Data
delivered or otherwise furnished shall be
marked and embedded as appropriate
with the following “Notice of Use”, and be
treated in accordance with such Notice:

Severability:
You and HERE agree that if any portion of
this agreement is found illegal or
unenforceable, that portion shall be
severed and the remainder of the
Agreement shall be given full force and
effect.

NOTICE OF USE
CONTRACTOR
(MANUFACTURER/SUPPLIER)

Severability:

NAME:

You and HERE agree that if any portion of
this agreement is found illegal or
unenforceable, that portion shall be
severed and the remainder of the
Agreement shall be given full force and
effect.

HERE
CONTRACTOR
(MANUFACTURER/SUPPLIER)
ADDRESS:
425 West Randolph Street, Chicago, IL
60606.

Governing Law:

This Data is a commercial item as defined
in FAR 2.101

The above terms and conditions shall be
governed by the laws of the State of Illinois
(for Data for the Americas and/or the Asia
Pacific region) or The Netherlands (for
Data for Europe, the Middle East and
Africa), without giving effect to (i) its
conflict of laws provisions, or (ii) the United
Nations Convention for Contracts for the
International Sale of Goods, which is
explicitly excluded. For any and all
disputes, claims and actions arising from
or in connection with the Data (“Claims”),
you agree to submit to the personal
jurisdiction of (a) the State of Illinois for
Claims related to Data for the Americas
and/or the Asia Pacific region provided to
you hereunder, and (b) The Netherlands
for Data for Europe, the Middle East and/or
Africa provided to you hereunder.

and is subject to the End User License
Agreement under
which this Data was provided.
© 1987-2013 HERE. All rights reserved.
If the Contracting Officer, federal
government agency, or any federal official
refuses to use the legend provided herein,
the Contracting Officer, federal
government agency, or any federal official
must notify HERE prior to seeking
additional or alternative rights in the Data.

433

F150 (TF6) , enUSA

Appendices
Gracenote® Copyright

You agree that you will use the content
from Gracenote ("Gracenote Content") ,
Gracenote Data, the Gracenote Software,
and Gracenote Servers for your own
personal, non-commercial use only. You
agree not to assign, copy, transfer or
transmit the Gracenote Content,
Gracenote Software or any Gracenote
Data (except in a Tag associated with a
music file) to any third party. YOU AGREE
NOT TO USE OR EXPLOIT GRACENOTE
CONTENT, GRACENOTE DATA, THE
GRACENOTE SOFTWARE, OR
GRACENOTE SERVERS, EXCEPT AS
EXPRESSLY PERMITTED HEREIN.

CD and music-related data from
Gracenote, Inc., copyright© 2000-2007
Gracenote. Gracenote Software, copyright
© 2000-2007 Gracenote. This product and
service may practice one or more of the
following U.S. Patents #5,987,525,
#6,061,680, #6,154,773, #6,161,132,
#6,230,192, #6,230,207, #6.240,459,
#6,330,593 and other patents issued or
pending. Some services supplied under
license from Open Globe, Inc. for U.S.
Patent: #6,304,523.
Gracenote and CDDB are registered
trademarks of Gracenote. The Gracenote
logo and logotype, and the "Powered by
Gracenote™" logo are trademarks of
Gracenote.

You agree that your non-exclusive licenses
to use the Gracenote Content, Gracenote
Data, the Gracenote Software, and
Gracenote Servers will terminate if you
violate these restrictions. If your licenses
terminate, you agree to cease any and all
use of the Gracenote Content, Gracenote
Data, the Gracenote Software, and
Gracenote Servers. Gracenote,
respectively, reserve all rights in Gracenote
Data, the Gracenote Software, and the
Gracenote Servers and Gracenote Content,
including all ownership rights. Under no
circumstances will either Gracenote
become liable for any payment to you for
any information that you provide, including
any copyrighted material or music file
information. You agree that Gracenote
may enforce its respective rights,
collectively or separately, under this
agreement against you, directly in each
company's own name.

Gracenote® End User License Agreement
(EULA)
This device contains software from
Gracenote, Inc. of 2000 Powell Street
Emeryville, California 94608
("Gracenote").
The software from Gracenote (the
"Gracenote Software") enables this device
to do disc and music file identification and
obtain music-related information, including
name, artist, track, and title information
("Gracenote Data") from online servers
("Gracenote Servers"), and to perform
other functions. You may use Gracenote
Data only by means of the intended End
User functions of this device.
This device may contain content belonging
to Gracenote's providers. If so, all of the
restrictions set forth herein with respect to
Gracenote Data shall also apply to such
content and such content providers shall
be entitled to all of the benefits and
protections set forth herein that are
available to Gracenote.

Gracenote uses a unique identifier to track
queries for statistical purposes. The
purpose of a randomly assigned numeric
identifier is to allow Gracenote to count
queries without knowing anything about
who you are. For more information, see the
web page at www.gracenote.com for the
Gracenote Privacy Policy.

434

F150 (TF6) , enUSA

Appendices
THE GRACENOTE SOFTWARE, EACH ITEM
OF GRACENOTE DATA AND THE
GRACENOTE CONTENT ARE LICENSED
TO YOU "AS IS". NEITHER GRACENOTE
MAKES ANY REPRESENTATIONS OR
WARRANTIES, EXPRESS OR IMPLIED,
REGARDING THE ACCURACY OF ANY
GRACENOTE DATA FROM THE
GRACENOTE SERVERS OR GRACENOTE
CONTENT. GRACENOTE COLLECTIVELY
AND SEPARATELY RESERVE THE RIGHT
TO DELETE DATA AND/OR CONTENT
FROM THE COMPANIES' RESPECTIVE
SERVERS OR, IN THE CASE OF
GRACENOTE, CHANGE DATA
CATEGORIES FOR ANY CAUSE THAT
GRACENOTE DEEMS SUFFICIENT. NO
WARRANTY IS MADE THAT EITHER
GRACENOTE CONTENT OR THE
GRACENOTE SOFTWARE OR
GRACENOTE SERVERS ARE ERROR-FREE
OR THAT THE FUNCTIONING OF THE
GRACENOTE SOFTWARE OR
GRACENOTE SERVERS WILL BE
UNINTERRUPTED. GRACENOTE IS NOT
OBLIGATED TO PROVIDE YOU WITH ANY
ENHANCED OR ADDITIONAL DATA TYPES
THAT GRACENOTE MAY CHOOSE TO
PROVIDE IN THE FUTURE AND IS FREE
TO DISCONTINUE ITS ONLINE SERVICES
AT ANY TIME. GRACENOTE DISCLAIM ALL
WARRANTIES EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO,
IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, TITLE, AND
NON-INFRINGEMENT. NEITHER
GRACENOTE WARRANTS THE RESULTS
THAT WILL BE OBTAINED BY YOUR USE
OF THE GRACENOTE SOFTWARE OR ANY
GRACENOTE SERVER. IN NO CASE WILL
GRACENOTE BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL
DAMAGES OR FOR ANY LOST PROFITS
OR LOST REVENUES FOR ANY REASON
WHATSOEVER.

Vehicle with SYNC only
FCC ID: KMHSG1G1
IC: 1422A-SG1G1
Vehicle with SYNC and MyFord Touch
or MyLincoln Touch
FCC ID: KMHSYNCG2–L
IC: 1422A-SYNCG2–L
This device complies with Part 15 of the
FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
WARNING
Changes or modifications not
expressively approved by the party
responsible for compliance could
void the user's authority to operate the
equipment. The term "IC" before the radio
certification number only signifies that
Industry Canada technical specifications
were met.
The antenna used for this transmitter must
not be co-located or operating in
conjunction with any other antenna or
transmitter.

435

F150 (TF6) , enUSA

Extended Service Plan (ESP)
PROTECT YOURSELF FROM THE RISING
COST OF VEHICLE REPAIRS WITH A FORD
EXTENDED SERVICE PLAN.

That means you get:
• Reliable, quality service at any Ford or
Lincoln dealership
• Repairs performed by factory trained
technicians, using genuine parts

SERVICE PLANS (U.S. Only)
More than 32 million Ford owners have
discovered the powerful protection of Ford
Extended Service Plan. It is the only
extended service plan backed by Ford
Motor Company, and provides peace of
mind protection beyond the New Vehicle
Limited Warranty coverage.

Rental Car Reimbursement
1st day Rental Benefit
You take advantage of replacement
transportation if your vehicle is at your
authorized dealer for same day covered
repairs.

Ford ESP Can Quickly Pay for Itself
One service bill – the cost of parts and
labor – can easily exceed the price of your
Ford Extended Service Plan. With Ford ESP
you minimize your risk for unexpected
repair bills and rising repair costs.

Extended Rental Benefits

Up to 1,000+ Covered Vehicle
Components

Roadside Assistance

If your vehicle is kept overnight for covered
repairs, you are eligible for rental car
coverage, including bumper to bumper
warranty repairs, and Field Service Actions.

Exclusive 24/7 roadside assistance,
including:

There are four Extended Service Plans with
different levels of coverage. Ask your
authorized dealer for details.

•

PremiumCARE - Our most
comprehensive coverage. With over
1,000 covered components, this plan
is so complete that we generally only
discuss what’s not covered.
2. ExtraCARE - Covers 113 components,
and includes many high-tech items.
3. BaseCARE - Covers 84 components.
4. PowertrainCARE - Covers 29 critical
components.

•
•
•

Transferable Coverage
If you sell your vehicle before your Ford
Extended Service Plan coverage expires,
you can transfer any remaining coverage
to the new owner. Whenever you sell your
vehicle, prospective buyers may have a
higher degree of confidence that vehicle
was properly maintained with Ford ESP,
thereby improving resale value.

Ford Extended Service Plan is honored by
all authorized Ford dealers in the U.S. and
Canada. It is the only extended service plan
authorized and backed by Ford Motor
Company.

436

F150 (TF6) , enUSA

Towing, flat-tire change and battery
jump starts
Out of fuel and lock-out assistance
Travel expense reimbursement for
lodging, meals and rental car
Destination assistance for taxi, shuttle,
rental car coverage and emergency
transportation

Extended Service Plan (ESP)
SERVICE PLANS (CANADA ONLY)

Avoid the Rising Cost of Properly
Maintaining Your Vehicle!

You can get more protection for your
vehicle by purchasing a Ford Extended
Service Plan. Ford Extended Service Plan
is the only service contract backed by Ford
Motor Company of Canada, Limited.
Depending on the plan you purchase, Ford
Extended Service Plan provides benefits
such as:

Ford Extended Service Plan also offers a
Premium Maintenance Plan that covers all
scheduled maintenance, and selected
wear items. The coverage is prepaid, so
you never have to worry about affording
your vehicle’s maintenance. It covers
regular checkups, routine inspections,
preventive care and replacement of select
items that require periodic attention for
normal wear:
•
•
•
•
•
•
•

•
•

Windshield wiper blades
Spark plugs (except in California)
The clutch disc
Brake pads and linings
Shock absorbers
Belts and hoses
Diesel exhaust fluid replenishment

•

There are several Ford Extended Service
Plans available in various time, distance
and deductible combinations. Each plan
is tailored to fit your own driving needs,
including reimbursement for towing and
rental. When you purchase Ford Extended
Service Plan, you receive added
peace-of-mind protection throughout
Canada and the United States, provided
by a network of participating authorized
Ford Motor Company dealers.

Interest Free Finance Options
Available
Take advantage of our interest free
installment payment plan. Just a 10%
down payment will provide you with an
affordable, no interest, no fee payment
program allowing you all the security and
benefits Ford ESP has to offer while paying
over time. You are pre-approved with no
credit checks, no hassles! To learn more,
call our Ford ESP specialists at
800-367-3377.

Note: Repairs performed outside of Canada
and the United States are not eligible for
Ford Extended Service Plan coverage.
This information is subject to change. For
more information, visit your local Ford of
Canada dealer or www.ford.ca to find the
Ford Extended Service Plan that is right for
you.

Ford ESP
P.O. Box 8072
Royal Oak, MI 48068-0039

437

F150 (TF6) , enUSA

Rental reimbursement
Coverage for certain maintenance and
wear items
Protection against repair costs after
your New Vehicle Limited Warranty
Coverage expires
Roadside Assistance benefits

Scheduled Maintenance
Genuine Ford and Motorcraft
Replacement Parts

GENERAL MAINTENANCE
INFORMATION

Dealerships stock Ford, Motorcraft and
Ford-authorized branded re-manufactured
replacement parts. These parts meet or
exceed our specifications. Parts installed
at your dealership carry a nationwide
24-month or unlimited mile (kilometer)
parts and labor limited warranty.

Why Maintain Your Vehicle?
Carefully following the maintenance
schedule helps protect against major repair
expenses resulting from neglect or
inadequate maintenance and may help to
increase the value of your vehicle when
you sell or trade it. Keep all receipts for
completed maintenance with your vehicle.

If you do not use Ford authorized parts they
may not meet our specifications and
depending on the part, it could affect
emissions compliance.

We have established regular maintenance
intervals for your vehicle based upon
rigorous testing. It is important that you
have your vehicle serviced at the proper
times. These intervals serve two purposes;
one is to maintain the reliability of your
vehicle and the second is to keep your cost
of owning your vehicle down.

Convenience
Many dealerships have extended evening
and Saturday hours to make your service
visit more convenient and they offer one
stop shopping. They can perform any
services that are required on your vehicle,
from general maintenance to collision
repairs.

It is your responsibility to have all
scheduled maintenance performed and to
make sure that the materials used meet
the specifications identified in this owner's
manual. See Capacities and
Specifications (page 296).

Note: Not all dealers have extended hours
or body shops. Please contact your dealer
for details.

Failure to perform scheduled maintenance
invalidates warranty coverage on parts
affected by the lack of maintenance.

Protecting Your Investment
Maintenance is an investment that pays
dividends in the form of improved
reliability, durability and resale value. To
maintain the proper performance of your
vehicle and its emission control systems,
make sure you have scheduled
maintenance performed at the designated
intervals.

Why Maintain Your Vehicle at Your
Dealership?
Factory-trained Technicians
Service technicians participate in extensive
factory-sponsored certification training to
help them become experts on the
operation of your vehicle. Ask your
dealership about the training and
certification their technicians have
received.

Vehicles with a 3.5L, 3.7L or 5.0L
Engine
Your vehicle is equipped with the
Intelligent Oil-Life Monitor system, which
displays a message in the information
display at the proper oil change interval.
This interval may be up to one year or
10000 miles (16000 kilometers).

438

F150 (TF6) , enUSA

Scheduled Maintenance
When ENGINE OIL CHANGE DUE or OIL
CHANGE REQUIRED appears in the
information display, it is time for an oil
change. Make sure you perform the oil
change within two weeks or 500 miles
(800 kilometers) of the ENGINE OIL
CHANGE DUE or OIL CHANGE
REQUIRED message appearing. Make
sure you reset the Intelligent Oil-Life
Monitor after each oil change.

We strongly recommend the use of only
genuine Ford, Motorcraft or
Ford-authorized re-manufactured
replacement parts engineered for your
vehicle.
Additives and Chemicals
This owner's manual and the Ford
Workshop Manual list the recommended
additives and chemicals for your vehicle.
We do not recommend using chemicals or
additives not approved by us as part of
your vehicle’s normal maintenance. Please
consult your warranty information.

If your information display resets
prematurely or becomes inoperative, you
should perform the oil change interval at
six months or 5000 miles (8000
kilometers) from your last oil change.
Never exceed one year or 10000 miles
(16000 kilometers) between oil change
intervals.

Oils, Fluids and Flushing
In many cases, fluid discoloration is a
normal operating characteristic and, by
itself, does not necessarily indicate a
concern or that the fluid needs to be
changed. However, a qualified expert, such
as the factory-trained technicians at your
dealership, should inspect discolored fluids
that also show signs of overheating or
foreign material contamination
immediately.

Vehicles with a 6.2L Engine
Your vehicle does not have an Intelligent
Oil-Life Monitor system. See the 7500 mile
(12000 kilometers) maintenance schedule
for oil change service intervals.
All Vehicles
Your vehicle is very sophisticated and built
with multiple, complex, performance
systems. Every manufacturer develops
these systems using different
specifications and performance features.
That is why it is important to rely upon your
dealership to properly diagnose and repair
your vehicle.

Make sure to change your vehicle’s oils and
fluids at the specified intervals or in
conjunction with a repair. Flushing is a
viable way to change fluid for many vehicle
sub-systems during scheduled
maintenance. It is critical that systems are
flushed only with new fluid that is the same
as that required to fill and operate the
system or using a Ford-approved flushing
chemical.

Ford Motor Company has recommended
maintenance intervals for various parts
and component systems based upon
engineering testing. Ford Motor Company
relies upon this testing to determine the
most appropriate mileage for replacement
of oils and fluids to protect your vehicle at
the lowest overall cost to you and
recommends against maintenance
schedules that deviate from the scheduled
maintenance information.

Owner Checks and Services
Make sure you perform the following basic
maintenance checks and inspections every
month or at six-month intervals.

439

F150 (TF6) , enUSA

Scheduled Maintenance

Check every month

Engine oil level.
Function of all interior and exterior lights.
Tires (including spare) for wear and proper pressure.
Windshield washer fluid level.

Check every six months

Battery connections. Clean if necessary.
Body and door drain holes for obstructions. Clean if necessary.
Cooling system fluid level and coolant strength.
Door weatherstrips for wear. Lubricate if necessary.
Hinges, latches and outside locks for proper operation. Lubricate if necessary.
Parking brake for proper operation.
Safety belts and seat latches for wear and function.
Safety warning lamps (brake, ABS, airbag and safety belt) for operation.
Washer spray and wiper operation. Clean or replace blades as necessary.

Multi-point Inspection
In order to keep your vehicle running right,
it is important to have the systems on your
vehicle checked regularly. This can help
identify potential issues and prevent major
problems. We recommend having the
following multi-point inspection performed
at every scheduled maintenance interval
to help make sure your vehicle keeps
running great.

440

F150 (TF6) , enUSA

Scheduled Maintenance

Multi-point inspection

Accessory drive belt(s)

Horn operation

Battery performance

Radiator, cooler, heater and A/C hoses

Engine air filter

Suspension component for leaks or
damage

Exhaust system

Steering and linkage

Exterior lamps and hazard warning system Tires (including spare) for wear and proper
**
operation
pressure
Fluid levels ; fill if necessary

Windshield for cracks, chips or pits

For oil and fluid leaks

Washer spray and wiper operation

Brake, coolant recovery reservoir, automatic transmission, power steering (if equipped
with hydraulic power assist steering) and window washer.
**

If your vehicle is equipped with a temporary mobility kit, check the tire sealant expiration
Use By date on the canister. Replace as needed.
This means you do not have to remember
to change the oil on a mileage-based
schedule. Your vehicle lets you know when
an oil change is due by displaying ENGINE
OIL CHANGE DUE or OIL CHANGE
REQUIRED in the information display.

Be sure to ask your dealership service
advisor or technician about the multi-point
vehicle inspection. It is a comprehensive
way to perform a thorough inspection of
your vehicle. Your checklist gives you
immediate feedback on the overall
condition of your vehicle.

The following table provides examples of
vehicle use and its impact on oil change
intervals. It is a guideline only. Actual oil
change intervals depend on several factors
and generally decrease with severity of
use.

NORMAL SCHEDULED
MAINTENANCE
Intelligent Oil-Life Monitor®
(Vehicles with a 3.5L, 3.7L and
5.0L Engine)
Your vehicle is equipped with an Intelligent
Oil-Life Monitor that determines when you
should change the engine oil based on how
your vehicle is used. By using several
important factors in its calculations, the
monitor helps reduce the cost of owning
your vehicle and reduces environmental
waste at the same time.

441

F150 (TF6) , enUSA

Scheduled Maintenance

When to expect the OIL CHANGE REQUIRED message
Interval

Vehicle use and example

Normal
7500-10000 miles
(12000-16000 km)

Normal commuting with highway driving
No, or moderate, load or towing
Flat to moderately hilly roads
No extended idling
Severe

5000-7499 miles
(8000-11999 km)

3000-4999 miles
(4800-7999 km)

Moderate to heavy load or towing
Mountainous or off-road conditions
Extended idling
Extended hot or cold operation
Extreme
Maximum load or towing
Extreme hot or cold operation

442

F150 (TF6) , enUSA

Scheduled Maintenance
Normal Maintenance Intervals
3.5L, 3.7L and 5.0L Engines
*

At every oil change interval as indicated by the information display
**

Change engine oil and filter.

Rotate tires, inspect tire wear and measure tread depth.
Perform a multi-point inspection (recommended).
Inspect the automatic transmission fluid level (if equipped with dipstick). Consult your
dealer for requirements.
Inspect the brake pads, shoes, rotors, drums, brake linings, hoses and parking brake.
Inspect the engine cooling system strength and hoses.
Inspect the exhaust system and heat shields.
Inspect front axle and U-joints. Lubricate if equipped with grease fittings (Four–wheel
drive vehicles).
Inspect the half-shaft boots.
Inspect the steering linkage, ball joints, suspension, tire-rod ends, driveshaft and Ujoints. Lubricate any areas with grease fittings.
Inspect the wheels and related components for abnormal noise, wear, looseness or
drag.
*

Do not exceed one year or 10000 miles (16000 kilometers) between service intervals.

Reset the Intelligent Oil-Life Monitor after engine oil and filter changes.

Other maintenance items

Replace climate-controlled (heated and cooled) seat filter
Every 30000 miles (48000 (if equipped).
km)
Replace engine air filter.
At 100000 miles (160000
km)
Every 100000 miles
(160000 km)

Change engine coolant.
Replace spark plugs.

Inspect accessory drive belt(s).

443

F150 (TF6) , enUSA

Scheduled Maintenance
Other maintenance items

Change automatic transmission fluid and filter.
Change front axle fluid (Four-wheel drive vehicles).
Every 150000 miles
(240000 km)

Change rear axle fluid.
Change transfer case fluid (Four-wheel drive vehicles).
Replace accessory drive belt(s).

Perform these maintenance items within 3000 miles (4800 kilometers) of the last
engine oil and filter change. Do not exceed the designated distance for the interval.
2

Initial replacement at six years or 100000 miles (160000 kilometers), then every three
years or 50000 miles (80000 kilometers).
3

After initial inspection, inspect every other oil change until replaced.

6.2L Engine
Every 7500 miles (12000 km) or six months (whichever comes first)

Change engine oil and filter.
*

Rotate tires , inspect tire wear and measure tread depth.
Inspect wheels and related components for abnormal noise, wear, looseness or drag.
Perform multi-point inspection (recommended).
*

The SVT Raptor has a specific tire rotation interval. See the supplement for more
information.

Every 15000 miles (24000 km) or 12 months (whichever comes first)

Inspect automatic transmission fluid level. Consult dealer for requirements.
Inspect brake pads, shoes, rotors, drums, brake linings, hoses and parking brake.
Inspect engine cooling system strength and hoses.
Inspect exhaust system and heat shields.

444

F150 (TF6) , enUSA

Scheduled Maintenance
Every 15000 miles (24000 km) or 12 months (whichever comes first)

Inspect front axle and U-joints. Lubricate if equipped with grease fittings (Four-wheel
drive vehicles).
Inspect half-shaft boots (if equipped).
Inspect steering linkage, ball joints, suspension, tie-rod ends, driveshaft and U-joints.
Lubricate if equipped with grease fittings.

Other maintenance items

Replace climate-controlled (heated and cooled) seat filter
Every 30000 miles (48000 (if equipped).
km)
Replace engine air filter.
Every 97500 miles (156000 Replace spark plugs.
km)
Every 105000 miles
(168000 km)

Change engine coolant.

Inspect accessory drive belt(s).

Change automatic transmission fluid and filter.
Change front axle fluid (Four-wheel drive vehicles).
Every 150000 miles
(240000 km)

Change rear axle fluid.
Change transfer case fluid (Four-wheel drive vehicles).
Replace accessory drive belt(s) if not replaced within the
last 100000 miles (160000 km).

Initial replacement at six years or 105000 miles (168000 kilometers), then every three
years or 45000 miles (72000 kilometers).
**

If not replaced, inspect every 15000 miles (24000 kilometers).

445

F150 (TF6) , enUSA

Scheduled Maintenance
Perform the services shown in the
following tables when specified or within
3000 miles (4800 kilometers) of the OIL
CHANGE REQUIRED message appearing
in the information display.
• Example 1: The OIL CHANGE
REQUIRED message comes on at
28751 miles (46270 kilometers).
Perform the 30000-mile (48000
kilometer) automatic transmission
fluid replacement.
• Example 2: The OIL CHANGE
REQUIRED message has not come
on, but the odometer reads 30000
miles (48000 kilometers) (for
example, the Intelligent Oil-Life
Monitor was reset at 25000 miles
[40000 kilometers]). Perform the
engine air filter replacement.

SPECIAL OPERATING
CONDITIONS SCHEDULED
MAINTENANCE
3.5L, 3.7L and 5.0L Engines
If you operate your vehicle primarily in any
of the following conditions, you need to
perform extra maintenance as indicated.
If you operate your vehicle occasionally
under any of these conditions, it is not
necessary to perform the extra
maintenance. For specific
recommendations, see your dealership
service advisor or technician.

Towing a trailer or using a car-top carrier

As required

Change engine oil and filter as indicated by the information
display and perform services listed in the Normal Scheduled Maintenance chart.

Inspect frequently, service
as required

Inspect and lubricate U-joints.
See axle maintenance items under Exceptions.

Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)

Extensive idling or low-speed driving for long distances, as in heavy commercial use
(such as delivery, taxi, patrol car or livery)

As required

Change engine oil and filter as indicated by the information
display and perform services listed in the Normal Scheduled Maintenance chart.

Inspect frequently, service
as required

Replace engine air filter.

Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)
Replace spark plugs.

446

F150 (TF6) , enUSA

Scheduled Maintenance

Operating in dusty or sandy conditions (such as unpaved or dusty roads)

Inspect frequently, service
as required

Replace engine air filter.

Every 5000 miles (8000
km)

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.
Rotate tires, inspect tires for wear and measure tread
depth.

Every 5000 miles (8000
km) or six months

Change engine oil and filter.

Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)
*

Reset your Intelligent Oil-Life Monitor after each engine oil and filter change.

Off-road operation

Inspect frequently, service
as required

Inspect steering linkage, ball joints and U-joints, Lubricate
if equipped with grease fittings.
Replace engine air filter.

Every 5000 miles (8000
km) or six months

Change engine oil and filter.

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.
Rotate tires, inspect tires for wear and measure tread
depth.
Every 30000 miles (48000 Replace front wheel bearing grease and grease seals if
km)
non-sealed bearings are used (Two-wheel drive vehicles).
Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)
*

Reset your Intelligent Oil-Life Monitor after each engine oil and filter change.

Exclusive use of E85 (Flex fuel vehicles only)

Every oil change interval

If ran exclusively on E85, fill the fuel tank full with regular
unleaded fuel.

447

F150 (TF6) , enUSA

Scheduled Maintenance
6.2L Engine

under any of these conditions, it is not
necessary to perform the extra
maintenance. For specific
recommendations, see your dealership
service advisor or technician.

If you operate your vehicle primarily in any
of the following conditions, you need to
perform extra maintenance as indicated.
If you operate your vehicle occasionally

Towing a trailer or using a car-top carrier

Inspect frequently, service
as required

Inspect and lubricate U-joints.

Every 5000 miles (8000
km)

Inspect wheels and related components for abnormal
noise, wear, looseness or drag.

See axle maintenance items under Exceptions.

Rotate tires, inspect tires for wear and measure tread
depth.
Every 5000 miles (8000
km) or six months

Change engine oil and filter.

Inspect and lubricate U-joints.
Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)
*

Reset your oil life monitoring system after each engine oil and filter change.

Extensive idling or low-speed driving for long distances, as in heavy commercial use
(such as delivery, taxi, patrol car or livery)

Inspect frequently, service
as required

Replace engine air filter.

Every 5000 miles (8000
km)

Inspect brake system.
Inspect wheels and related components for abnormal
noise, wear, looseness or drag.
Lubricate control arm and steering ball joints if equipped
with grease fittings.
Rotate tires, inspect tires for wear and measure tread
depth.

Every 5000 miles (8000
km) or six months

Change engine oil and filter.

448

F150 (TF6) , enUSA

Scheduled Maintenance
Extensive idling or low-speed driving for long distances, as in heavy commercial use
(such as delivery, taxi, patrol car or livery)

Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)
Replace spark plugs.
*

Reset your oil life monitoring system after each engine oil and filter change.

Operating in dusty or sandy conditions (such as unpaved or dusty roads)

Inspect frequently, service
as required

Replace engine air filter.

Every 5000 miles (8000
km)

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.
Rotate tires, inspect tires for wear and measure tread
depth.

Every 5000 miles (8000
km) or six months

Change engine oil and filter.

Inspect and lubricate U-joints.
Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)
*

Reset your oil life monitoring system after each engine oil and filter change.

Off-road operation

Inspect frequently, service
as required

Inspect steering linkage, ball joints and U-joints, Lubricate
if equipped with grease fittings.
Replace engine air filter.

Every 5000 miles (8000
km) or six months

Change engine oil and filter.

Inspect the wheels and related components for abnormal
noise, wear, looseness or drag.
Rotate tires, inspect tires for wear and measure tread
depth.
Every 60000 miles (96000 Change transfer case fluid (Four-wheel drive vehicles).
km)
*

Reset your oil life monitoring system after each engine oil and filter change.

449

F150 (TF6) , enUSA

Scheduled Maintenance

Exclusive use of E85 (Flex fuel vehicles only)

Every oil change interval

If ran exclusively on E85, fill the fuel tank full with regular
unleaded fuel.
F1TZ-19580-B, or equivalent. Add four
ounces (118 milliliters) of additive friction
modifier XL-3 (EST-M2C118-A), or
equivalent, for complete refill of
Traction-Lok rear axles. Change the axle
fluid anytime the axle submerges in water.

Exceptions
There are several exceptions to the Normal
Schedule:
Normal vehicle axle maintenance: Rear
axles and power take-off units with
synthetic fluid and light-duty trucks
equipped with Ford-design axles are
lubricated for life; do not check or change
fluid unless a leak is suspected, service is
required or the assembly has been
submerged in water. During long periods
of trailer towing with outside temperatures
above 70°F (21°C) and at wide-open
throttle for long periods above 45 mph (72
km/h), change non-synthetic rear axle fluid
every 3000 miles (4800 kilometers) or
three months, whichever comes first. This
interval can be waived if the axle is filled
with 75W140 synthetic gear fluid meeting
Ford specification WSL-M2C192-A, part
number F1TZ-19580-B, or equivalent. Add
friction modifier XL-3 (EST-M2C118-A) or
equivalent for complete refill of
Traction-Lok rear axles. See Capacities
and Specifications (page 296).

California fuel filter replacement: If you
register your vehicle in California, the
California Air Resources Board has
determined that the failure to perform this
maintenance item does not nullify the
emission warranty or limit recall liability
before the completion of your vehicle's
useful life. Ford Motor Company, however,
urges you to have all recommended
maintenance services performed at the
specified intervals and to record all vehicle
service.
Hot climate oil change intervals:
Vehicles operating in the Middle East,
North Africa, Sub-Saharan Africa or
locations with similar climates using an
American Petroleum Institute (API)
Certified for Gasoline Engines (Certification
mark) oil of SM or SN quality, the normal
oil change interval is 5000 miles (8000
kilometers).

Police, Taxi and Livery vehicle axle
maintenance: Change rear axle fluid every
100000 miles (160000 kilometers). Rear
axle fluid change may be waived if the axle
was filled with 75W140 synthetic gear fluid
meeting Ford specification
WSL-M2C192-A, part number

If the available API SM or SN oils are not
available, then the oil change interval is
3000 miles (4800 kilometers).
Engine air filter replacement: The life of
the engine air filter is dependent on
exposure to dusty and dirty conditions.
Vehicles operated in these conditions
require frequent inspection and
replacement of the engine air filter.

450

F150 (TF6) , enUSA

Scheduled Maintenance
SCHEDULED MAINTENANCE RECORD

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

451

F150 (TF6) , enUSA

Scheduled Maintenance

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

452

F150 (TF6) , enUSA

Scheduled Maintenance

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

453

F150 (TF6) , enUSA

Scheduled Maintenance

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

454

F150 (TF6) , enUSA

Scheduled Maintenance

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

455

F150 (TF6) , enUSA

Scheduled Maintenance

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

456

F150 (TF6) , enUSA

Scheduled Maintenance

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

Repair Order #:

Dealer stamp

Distance:

Engine hours (optional):

Multi-point inspection (recommended):
Signature:
E146852

457

F150 (TF6) , enUSA

458

F150 (TF6) , enUSA

Index

Audio Control..................................................66
Media.........................................................................67
Seek, Next or Previous........................................67
Type 1........................................................................66
Type 2.......................................................................66

4WD
See: Four-Wheel Drive......................................153

Audio Input Jack............................................321
Audio System...............................................306
General Information.........................................306

A/C

Audio unit - Vehicles With: AM/FM/CD/
SYNC/Satellite Radio.............................308
Audio unit - Vehicles With: AM/FM.......307
Audio unit - Vehicles With: Sony AM/FM/
CD....................................................................315
Autolamps..........................................................71
Automatic Climate Control......................109
Automatic Transmission............................147

See: Climate Control.........................................106

About This Manual...........................................7
Protecting the Environment................................7

ABS
See: Brakes............................................................163

ABS driving hints
See: Hints on Driving With Anti-Lock
Brakes................................................................163

Brake-Shift Interlock.........................................150
If Your Vehicle Gets Stuck In Mud or
Snow...................................................................152
Understanding the Shift Positions of a
6–Speed Automatic Transmission.........147
Understanding your SelectShift
Automatic® transmission..........................149

Accessories.....................................................419
Exterior style.........................................................419
Interior style..........................................................419
Lifestyle..................................................................419
Peace of mind......................................................419

Accessories
See: Replacement Parts
Recommendation.............................................11

Automatic Transmission Fluid
Check.............................................................245
Autowipers.......................................................69
Auxiliary Power Points................................132

Adjusting the Headlamps........................249
Horizontal Aim Adjustment............................251
Vertical Aim Adjustment................................249

110 Volt AC Power Points.................................132
12 Volt DC Power Point.....................................132
Locations................................................................132

Adjusting the Pedals....................................68
Adjusting the Steering Wheel...................65
Power Tilt and Telescope Steering
Column................................................................65

Airbag Disposal..............................................48
Air Conditioning

Bonnet Lock

See: Climate Control.........................................106

See: Opening and Closing the Hood..........235

Alarm

Booster Seats..................................................24

See: Anti-Theft Alarm........................................62

Anti-Theft Alarm............................................62

Types of Booster Seats......................................25

Arming the Alarm.................................................62
Disarming the Alarm...........................................62

Brake Fluid Check........................................246
Brakes...............................................................163
General Information..........................................163

Appendices.....................................................421
Audible Warnings and Indicators.............85

Breaking-In......................................................210
Bulb Specification Chart...........................254

Headlamps On Warning Chime......................85
Key in Ignition Warning Chime........................85
Parking Brake On Warning Chime.................86

C
California Proposition 65..............................11
Capacities and Specifications................296
Technical Specifications..................................301

459

F150 (TF6) , enUSA

Index
Cleaning the Exterior..................................259

Car Wash

Cleaning Plastic Exterior Parts.....................260
Exterior Chrome.................................................259
Stripes or Graphics (if equipped)................259
Underbody...........................................................260

See: Cleaning the Exterior..............................259

Center Console..............................................134
Changing a Bulb...........................................252
Lamp Assembly Condensation....................252
Replacing Brake/Tail/Turn/Reverse Lamp
Bulbs..................................................................253
Replacing Cargo Lamp and High-mount
Brake Lamp Bulbs........................................253
Replacing exterior mounted mirror turn
signal indicator lamp bulbs......................254
Replacing Fog Lamp Bulbs (If
Equipped..........................................................253
Replacing the License Plate Lamp
Bulb....................................................................254

Cleaning the Instrument Panel and
Instrument Cluster Lens..........................261
Cleaning the Interior....................................261
Cleaning the Windows and Wiper
Blades............................................................261
Clearing All MyKeys.......................................55
Climate...........................................................408
Climate Control Voice Commands............409

Climate Control............................................106
Coolant Check

Changing a Fuse...........................................233

See: Engine Coolant Check.............................241

Fuses.......................................................................233

Crash Sensors and Airbag Indicator.......48
Creating a MyKey............................................53

Changing a Road Wheel...........................289
Dissimilar Spare Wheel and Tire Assembly
Information.....................................................289
Location of the Spare Tire and Tools........290
Tire Change Procedure.....................................291

Programming/Changing Configurable
Settings...............................................................54

Cruise Control..................................................67
Principle of Operation.......................................176

Changing the 12V Battery.........................246

Cruise control

Battery Management System (If
Equipped)........................................................248

See: Using Cruise Control................................176

Customer Assistance..................................219

Changing the Engine Air Filter - 3.5L
Ecoboost™.................................................256
Changing the Engine Air Filter - 3.7L/
5.0L/6.2L......................................................257
Changing the Wiper Blades.....................249
Checking MyKey System Status...............55
Checking the Wiper Blades.....................249
Child Restraint and Safety Belt
Maintenance..................................................37
Child Safety.......................................................14

D
Data Recording..................................................9
Event Data Recording...........................................9
Service Data Recording........................................9

Daytime Running Lamps.............................72
Digital Radio...................................................316
HD Radio Reception and Station
Troubleshooting..............................................317

Direction Indicators........................................73

General Information.............................................14

Child Safety Locks.........................................28

Lane Change..........................................................73

Left-Hand Side......................................................29
Right-Hand Side...................................................29

Driver and Passenger Airbags...................40
Children and Airbags..........................................40
Proper Driver and Front Passenger Seating
Adjustment.......................................................40

Child Seat Positioning..................................26
Cleaning Leather Seats.............................262

Driving Aids......................................................177
Driving Hints...................................................210
Driving Through Water.................................211
DRL

WITHOUT THE KING RANCH
EDITION............................................................262
WITH THE KING RANCH EDITION..............263

Cleaning Products.......................................259
Cleaning the Alloy Wheels.......................264
Cleaning the Engine...................................260

See: Daytime Running Lamps..........................72

460

F150 (TF6) , enUSA

Index

Essential Towing Checks...........................201
Before Towing a Trailer...................................206
Hitches....................................................................201
Launching or Retrieving a Boat or Personal
Watercraft (PWC)........................................207
Safety Chains......................................................202
Trailer Brakes.......................................................202
Trailer Lamps......................................................206
Trailer Towing Connector.................................201
Using a Step Bumper (If Equipped)..........206
When Towing a Trailer.....................................206

Economical Driving......................................210
Electronic Locking Differential.................161
Activating the Electronic Locking
Differential........................................................161

Emission Control System..........................144
On-Board Diagnostics (OBD-II)....................145
Readiness for Inspection/Maintenance
(I/M) Testing...................................................146

End User License Agreement...................421

Event Data Recording

SYNC® End User License Agreement
(EULA)...............................................................421

See: Data Recording..............................................9

Export Unique Options..................................13
Extended Service Plan (ESP).................436

Engine Block Heater.....................................137
Using the Engine Block Heater......................138

SERVICE PLANS (CANADA ONLY).............437
SERVICE PLANS (U.S. Only).........................436

Engine Coolant Check.................................241
Adding Engine Coolant....................................242
Checking the Engine Coolant.........................241
Recycled Engine Coolant................................242
Severe Climates.................................................243
What You Should Know About Fail-Safe
Cooling..............................................................243

Exterior Mirrors................................................76
Auto-dimming Feature (if equipped)...........77
Clearance Lamps .................................................77
Fold-Away Exterior Mirrors................................77
Heated Exterior Mirrors ......................................77
Integrated Blind Spot Mirror (If
Equipped)..........................................................78
Memory Mirrors .....................................................77
Power Exterior Mirrors.........................................76
Signal Indicator Mirrors ......................................77
Telescoping Mirrors .............................................77

Engine Immobilizer
See: Passive Anti-Theft System......................61

Engine Oil Check..........................................240
Adding Engine Oil..............................................240

Engine Oil Dipstick......................................240
Engine Specifications................................296
Drivebelt Routing...............................................296

Entertainment...............................................376
A/V Inputs............................................................392
AM/FM Radio......................................................378
Bluetooth Audio..................................................391
Browsing Device Content................................376
CD............................................................................387
SD Card Slot and USB Port...........................388
SIRIUS® Satellite Radio (If
Activated)........................................................383
Supported Media Players, Formats and
Metadata Information.................................391

Fastening the Safety Belts...........................31
Fastening the Cinch Tongue.............................32
Safety Belt Extension Assembly....................34
Safety Belt Locking Modes...............................32
Using Safety Belts During Pregnancy...........32
Using the Safety Belt with Cinch Tongue
(Front Center Seat).........................................31

Floor Mats.........................................................211
Fog Lamps - Front
See: Front Fog Lamps.........................................72

Foot Pedals
See: Adjusting the Pedals.................................68

Ford Credit..........................................................11
(U.S. Only).................................................................11

Four-Wheel Drive..........................................153
Front Fog Lamps.............................................72
Front Passenger Sensing System.............41

461

F150 (TF6) , enUSA

Index

Front Seat Armrest.......................................122
Fuel and Refueling.......................................139
Fuel Consumption........................................143

Handbrake

Calculating Fuel Economy..............................144
Filling the Tank.....................................................143

See: Parking Brake.............................................164

Hazard Warning Flashers..........................216
HDC

Fuel Filter........................................................246
Fuel Quality....................................................140

See: Using Hill Descent Control....................170

Choosing the Right Fuel With a Flex Fuel
Vehicle (If Equipped)...................................140
Choosing the Right Fuel Without a Flex Fuel
Vehicle (If Equipped)...................................140
Octane Recommendations............................140

Head Restraints..............................................114
Adjusting the Head Restraint..........................115

Heated Seats.................................................120
Rear Heated Seats...............................................121

Heated Windows and Mirrors....................112

Fuel Shutoff....................................................216
Fuses.................................................................225
Fuse Specification Chart...........................225

Heated Exterior Mirror........................................113
Heated Rear Window.........................................112

Heating

Auxiliary relay box (SVT Raptor
only)...................................................................233
Passenger Compartment Fuse
Panel..................................................................229
Power Distribution Box....................................225

See: Climate Control.........................................106

Hill Start Assist..............................................164
Using Hill Start Assist.......................................164

Hints on Controlling the Interior
Climate...........................................................110
Cooling the Interior Quickly...............................111
General Hints........................................................110
Heating the Interior Quickly..............................111
Recommended Settings for Cooling ...........112
Recommended Settings for Heating.............111
Side Window Defogging in Cold
Weather..............................................................112

G
Garage Door Opener
See: Universal Garage Door Opener............124

Gauges................................................................81
Engine Coolant Temperature Gauge............82
Engine Oil Pressure Gauge...............................82
Fuel Gauge..............................................................82
Information Display.............................................82
Transmission Fluid Temperature
Gauge...................................................................82

Hints on Driving With Anti-Lock
Brakes............................................................163
Hood Lock
See: Opening and Closing the Hood..........235

General Information on Radio
Frequencies...................................................49
General Maintenance Information.......438

Ignition Switch...............................................135
In California (U.S. Only)............................220
Information Display Control.......................67

Multi-point Inspection....................................440
Owner Checks and Services..........................439
Protecting Your Investment..........................438
Why Maintain Your Vehicle?.........................438
Why Maintain Your Vehicle at Your
Dealership?.....................................................438

Type 1.........................................................................67
Type 2........................................................................67

Information Displays.....................................87
General Information............................................87

Getting Assistance Outside the U.S. and
Canada..........................................................222
Getting the Services You Need................219
Away From Home...............................................219

462

F150 (TF6) , enUSA

Index
Information....................................................399

Interior Lamps..................................................73

911 Assist..............................................................405
Alerts......................................................................405
Calendar...............................................................405
Sirius Travel Link................................................402
SYNC Services (If Equipped, United States
Only).................................................................400
Vehicle Health Report......................................407

Front Row Map Lamps (if equipped)...........73
Rear Courtesy, Reading, Cargo Lamps (If
Equipped)...........................................................74
Rear Dome, Courtesy Lamps (If
Equipped)...........................................................74
Rear Dome Lamp (If Equipped).....................73

Interior Mirror....................................................78

Information Messages.................................98

Auto-Dimming Mirror..........................................79

4WD........................................................................105
AdvanceTrac® and Traction Control............98
Airbag.......................................................................98
Alarm and Security.............................................99
Battery and Charging System.........................99
Doors and Locks...................................................99
Drivetrain...............................................................100
Engine.....................................................................100
Fuel..........................................................................100
Key.............................................................................101
Maintenance.........................................................101
MyKey®..................................................................102
Off Road................................................................103
Park Aid..................................................................102
Park Brake.............................................................103
Tire Pressure Monitoring System.................104
Trailer......................................................................104

Introduction.........................................................7

J
Jump Starting the Vehicle.........................216
Connecting the Jumper Cables......................217
Jump Starting.......................................................218
Preparing Your Vehicle......................................217
Removing the Jumper Cables........................218

K
Keyless Entry...................................................58
SECURICODE™ KEYLESS ENTRY
KEYPAD..............................................................58

Keys and Remote Controls.........................49

Installing Child Seats.....................................15
Child Seats...............................................................15
Combining Safety Belt and LATCH Lower
Anchors for Attaching Child Safety
Seats.....................................................................22
Front Seat Tether Strap Attachment
(Regular Cab)...................................................23
Rear Seat Tether Strap Attachment
(SuperCab and SuperCrew).......................23
Use of Inboard Lower Anchors from the
Outboard Seating Positions (Center
Seating Use) ......................................................21
Using Lap and Shoulder Belts..........................16
Using Lap and Shoulder Belts (Front Center
Seating Position)..............................................18
Using Lower Anchors and Tethers for
CHildren (LATCH)...........................................20
Using Tether Straps.............................................22

Lighting Control................................................71
Headlamp Flasher.................................................71
High Beams..............................................................71

Lighting................................................................71
Limited Slip Differential..............................161
Load Carrying.................................................179
Load Limit........................................................179
Special Loading Instructions for Owners of
Pick-up Trucks and Utility-type
Vehicles.............................................................186
Vehicle Loading - with and without a
Trailer..................................................................179

Locking and Unlocking.................................57
Autolock and Autounlock..................................57
Battery Saver.........................................................58
Illuminated Entry..................................................58
Power Door Locks.................................................57
Remote Control.....................................................57
Smart Unlocks.......................................................57

Instrument Cluster.........................................81
Instrument Lighting Dimmer......................72

Locks...................................................................57

463

F150 (TF6) , enUSA

Index

Lug Nuts
See: Changing a Road Wheel.......................289

Oil Check

See: Engine Oil Check......................................240

General Information.........................................235

Opening and Closing the Hood..............235
Ordering Additional Owner's
Literature......................................................223

Manual Climate Control............................106
Manual Seats..................................................116

Overhead Console........................................134

Maintenance..................................................235

Obtaining a French Owner’s Manual..........223

Manual Lumbar ....................................................117
Moving the Seat Backward and
Forward...............................................................117
Recline Adjustment.............................................117

P
Parking Aid.......................................................172

Media Hub......................................................322
Memory Function..........................................118

Rear Sensing System.........................................172

Parking Aids.....................................................172
Parking Brake.................................................164
Passive Anti-Theft System..........................61

Easy Entry and Exit Feature.............................119

Message Center
See: Information Displays.................................87

SecuriLock™...........................................................61

Mirrors

PATS

See: Heated Windows and Mirrors................112
See: Windows and Mirrors................................75

See: Passive Anti-Theft System......................61

Pedals................................................................68
Perchlorate.........................................................11
Personal Safety System™..........................38

Mobile Communications Equipment.......12
Moonroof...........................................................79
Bounce-Back.........................................................80
Opening and Closing the Moonroof.............80
Venting the Moonroof........................................80

How Does the Personal Safety System
Work?..................................................................38

Phone...............................................................393

Motorcraft Parts..........................................298
MyFord Touch™...........................................359

Making Calls........................................................395
Pairing Subsequent Phones..........................395
Pairing Your Phone for the First
Time...................................................................394
Phone Menu Options.......................................395
Phone Settings...................................................397
Phone Voice Commands...............................398
Receiving Calls...................................................395
Text Messaging..................................................396

General Information.........................................359

MyKey Troubleshooting...............................56
MyKey™.............................................................53
Principle of Operation.........................................53

N
Navigation.......................................................410

Post-Crash Alert System...........................218
Power Door Locks

cityseekr.................................................................412
Map Mode.............................................................414
Navigation Map Updates.................................417
Navigation Voice Commands.........................417
Point of Interest (POI) Categories................412
Quick-touch Buttons........................................416
Setting a Destination.........................................411
Setting Your Navigation Preferences..........413

See: Locking and Unlocking..............................57

Power Running Boards................................63
Power Seats.....................................................117
Power Lumbar......................................................118
Power Recline........................................................117

Power Steering Fluid Check....................246
3.5L, 3.7L and 5.0L Engines...........................246
6.2L Engines........................................................246

Normal Scheduled Maintenance...........441
Intelligent Oil-Life Monitor® (Vehicles with
a 3.5L, 3.7L and 5.0L Engine)....................441
Normal Maintenance Intervals.....................443

464

F150 (TF6) , enUSA

Index
Reporting Safety Defects (Canada
Only)..............................................................224
Reporting Safety Defects (U.S.
Only)..............................................................223
Roadside Assistance...................................215

Power Windows..............................................75
Accessory Delay....................................................76
Bounce-Back..........................................................75
One-Touch Up or Down.....................................75
Power Sliding Back Window............................76
Window Lock..........................................................76

Vehicles Sold In Canada : Getting Roadside
Assistance........................................................215
Vehicles Sold In Canada : Using Roadside
Assistance........................................................215
Vehicles Sold In The U.S.: Getting Roadside
Assistance........................................................215
Vehicles Sold In The U.S. : Using Roadside
Assistance........................................................215

R
Rear Axle...........................................................161
Rear Seat Armrest........................................123
Rear Seats........................................................119
Folding up the Rear Seat Cushion (Super
Crew)...................................................................119
Returning the Seat to the Seating
Position...............................................................119

Roadside Emergencies...............................215
Running-In

Rear View Camera........................................173

Running Out of Fuel......................................141

Using the Rear View Camera System..........173

Refilling With a Portable Fuel
Container...........................................................141

See: Breaking-In..................................................210

Rear View Camera
See: Rear View Camera....................................173

Recommended Towing Weights............192
Calculating the Maximum Loaded Trailer
Weight for Your Vehicle..............................200

Safety Belt Height Adjustment.................34
Safety Belt Minder.........................................35

Refueling..........................................................142
Easy Fuel™ Capless Fuel System................142

Belt-Minder™........................................................35

Remote Control..............................................49

Safety Belts......................................................30

Car Finder................................................................50
Integrated Keyhead Transmitters .................49
Memory Feature...................................................50
Remote Start .........................................................51
Replacing the Battery.........................................49
Sounding a Panic Alarm.....................................51

Principle of Operation........................................30

Safety Belt Warning Lamp and Indicator
Chime..............................................................34
Conditions of operation.....................................35

Safety Canopy™............................................46
Safety Precautions.......................................139
Satellite Radio...............................................318

Remote Start...................................................113
Automatic Settings.............................................113

Satellite Radio Electronic Serial Number
(ESN)................................................................320
Satellite Radio Reception Factors...............319
SIRIUS® Satellite Radio Service...................319
Troubleshooting.................................................320

Removing a Headlamp...............................251
Replacing Halogen Headlamp Bulbs (If
Equipped).........................................................251
Replacing HID Headlamp Bulbs (If
Equipped)........................................................252

Scheduled Maintenance Record............451
Scheduled Maintenance..........................438
Seats...................................................................114
Security...............................................................61
Settings...........................................................366

Repairing Minor Paint Damage..............263
Replacement Parts
Recommendation.........................................11
Collision Repairs.....................................................11
Scheduled Maintenance and Mechanical
Repairs...................................................................11
Warranty on Replacement Parts.....................12

Clock.......................................................................367
Display....................................................................367
Settings.................................................................369
Sound....................................................................368
Vehicle...................................................................368

Replacing a Lost Key or Remote
Control.............................................................52

465

F150 (TF6) , enUSA

Index
Sunroof

Side Airbags.....................................................45
Sitting in the Correct Position...................114
Snow Chains

See: Moonroof.......................................................79

Sun Visors.........................................................79
Illuminated Vanity Mirror...................................79
Slide-on-rod...........................................................79

See: Using Snow Chains.................................283

Snowplowing..................................................212

Supplementary Restraints System.........39

Engine temperature while plowing..............213
Installing the Snowplow..................................212
Operating the Vehicle with the Snowplow
Attached............................................................213
Outside Air Temperature While
Plowing..............................................................214
Snowplowing with your Airbag Equipped
Vehicle................................................................213
Transmission operation while
plowing..............................................................214

Principle of Operation........................................39

Symbols Glossary.............................................7
SYNC™ Applications and
Services........................................................338
911 Assist...............................................................338
SYNC AppLink....................................................344
SYNC Services: Traffic, Directions &
Information (TDI) (If Equipped, Unites
States Only).....................................................341
Vehicle Health Report.....................................340

Special Notices................................................12
New Vehicle Limited Warranty.........................12
Special Instructions..............................................12

SYNC™............................................................323

Special Operating Conditions Scheduled
Maintenance..............................................446

SYNC™ Troubleshooting.........................353

General Information..........................................323

3.5L, 3.7L and 5.0L Engines...........................446
6.2L Engine..........................................................448
Exceptions...........................................................450

Tailgate.............................................................186

Speed Control

Bed Extender.......................................................189
Box Side Step......................................................188
Tailgate Lock........................................................186
Tailgate Removal................................................187
Tailgate Step.........................................................187

See: Cruise Control.............................................176

Stability Control............................................167
Principle of Operation.......................................167

Starter Switch

Technical Specifications

See: Ignition Switch...........................................135

Starting a Gasoline Engine........................135

See: Capacities and Specifications............296

Cold Weather Starting (Flexible Fuel
Vehicles Only).................................................136
Failure to Start.....................................................136
Guarding Against Exhaust Fumes................137
Important Ventilating Information...............137
Stopping the Engine When Your Vehicle is
Moving...............................................................136
Stopping the Engine When Your Vehicle is
Stationary.........................................................136

Terrain Response..........................................170
Principle of Operation.......................................170

The Better Business Bureau (BBB) Auto
Line Program (U.S. Only)........................221
Tire Care..........................................................268
Glossary of Tire Terminology........................269
Information About Uniform Tire Quality
Grading.............................................................268
Information Contained on the Tire
Sidewall............................................................270
Temperature A B C............................................269
Traction AA A B C..............................................269
Treadwear............................................................268

Starting and Stopping the Engine..........135
General Information..........................................135

Steering.............................................................177
Electric Power Steering (3.7L, 5.0L and 3.5L
EcoBoost™ engines)....................................177
Hydraulic Steering (6.2L engine)...................177

Tire Pressure Monitoring System...........283
Changing Tires With a Tire Pressure
Monitoring System.......................................284
Understanding Your Tire Pressure
Monitoring System ......................................285

Steering Wheel...............................................65
Storage Compartments.............................134

466

F150 (TF6) , enUSA

Index
Using Power Running Boards....................63

Tires

Towing the Vehicle on Four
Wheels.........................................................208

Automatic Power Deploy..................................63
Automatic Power Stow......................................63
Bounce-back.........................................................64
Enabling and Disabling......................................63
Manual Power Deploy........................................63

Emergency Towing...........................................208
Recreational Towing........................................208

Using Snow Chains.....................................283
Using Stability Control...............................168

Towing...............................................................191
Traction Control............................................166

AdvanceTrac™ with Roll Stability Control™
(RSC™)............................................................168

Principle of Operation......................................166

Using SYNC™ With Your Media
Player............................................................345

See: Wheels and Tires.....................................266

Towing a Trailer..............................................191
Load Placement...................................................191

Trailer Sway Control....................................192
Transfer Case Fluid Check........................245
Transmission Code Designation...........300
Transmission...................................................147
Transmission

Accessing Your Play Menu.............................349
Connecting Your Digital Media Player to the
USB Port..........................................................345
Media Menu Features......................................348
Media Voice Commands................................346
System Settings..................................................351
What's Playing?.................................................346

See: Transmission...............................................147

Transporting the Vehicle...........................207

Using SYNC™ With Your Phone.............327
Accessing Features through the Phone
Menu...................................................................331
Accessing Your Phone Settings....................334
Making Calls........................................................330
Pairing a Phone for the First Time...............328
Pairing Subsequent Phones..........................328
Phone Options during an Active Call.........330
Phone Voice Commands................................328
Receiving Calls...................................................330
System Settings.................................................335
Text Messaging...................................................333

Under Hood Overview - 3.5L
Ecoboost™.................................................236
Under Hood Overview - 3.7L....................237
Under Hood Overview - 5.0L..................238
Under Hood Overview - 6.2L...................239
Universal Garage Door Opener................124
CAR2U® Home Automation System..........124
HomeLink Wireless Control System............127

USB Port..........................................................322
Using Cruise Control....................................176

Using Traction Control...............................166

Switching Cruise Control Off..........................176
Switching Cruise Control On...........................176

System Indicator Lights and
Messages..........................................................166

Using Four-Wheel Drive.............................153

Using Voice Recognition...........................325

4WD Indicator Lights.........................................153
Driving Off-Road With Truck and Utility
Vehicles.............................................................156
How Your Vehicle Differs From Other
Vehicles.............................................................156
Using the 2-Speed Automatic 4WD
System...............................................................154
Using the Electronic Shift on the Fly 4WD
system................................................................153

Initiating a Voice Session................................325
System Interaction and Feedback..............326

Utilizing the Mediation/Arbitration
Program (Canada Only)..........................221

V
Vehicle Care...................................................259

Using Hill Descent Control........................170

General Information.........................................259

Hill descent modes............................................170

Vehicle Certification Label.......................299
Vehicle Identification Number...............298

Using MyKey With Remote Start
Systems..........................................................55

467

F150 (TF6) , enUSA

Index

Vehicle Storage............................................264
Battery...................................................................265
Body.......................................................................264
Brakes....................................................................265
Cooling system...................................................265
Engine....................................................................265
Fuel system..........................................................265
General..................................................................264
Miscellaneous.....................................................265
Removing Vehicle From Storage.................265
Tires........................................................................265

Warning Lamps and Indicators.................82
4X2............................................................................85
4X4 Auto.................................................................85
4X4 HIGH................................................................85
4X4 LOW.................................................................85
Anti-Lock Braking System................................83
Battery......................................................................83
Brake System.........................................................83
Check 4X4..............................................................83
Cruise Control........................................................83
Direction Indicator...............................................83
Door Ajar..................................................................83
Electronic Locking Differential........................83
Engine Coolant Temperature..........................83
Engine Oil................................................................83
Fasten Safety Belt...............................................84
Front Airbag...........................................................84
High Beam..............................................................84
Hill Descent............................................................84
Low Fuel Level......................................................84
Low Tire Pressure Warning...............................84
Powertrain Malfunction/Reduced
Power/Electronic Throttle Control...........84
Service Engine Soon...........................................84
Traction and Stability Control.........................85
Traction and Stability Control Off.................85
Transmission Tow/Haul....................................85

Ventilated Seats.............................................121
Heated and Ventilated Seats Air Filter
Replacement ..................................................122

Ventilation
See: Climate Control.........................................106

VIN
See: Vehicle Identification Number............298

Voice Control....................................................67

Washer Fluid Check....................................246
Washers
See: Cleaning the Exterior..............................259
See: Wipers and Washers.................................69

Waxing............................................................260
Wheel Nuts
See: Changing a Road Wheel.......................289

Wheels and Tires.........................................266
General Information.........................................266
Technical Specifications.................................294

Windows and Mirrors....................................75
Windshield Washers.....................................70
Windshield Wipers........................................69
Speed dependent wipers (if
equipped)..........................................................69

Wipers and Washers.....................................69

468

F150 (TF6) , enUSA

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Unknown
Create Date                     : 2014:02:14 21:11:51Z
Modify Date                     : 2014:03:03 10:32:28-05:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : Untitled
Creator                         : Unknown
Producer                        : XEP 4.16 build 20090723
Trapped                         : False
Creator Tool                    : Unknown
Metadata Date                   : 2014:03:03 10:32:28-05:00
Document ID                     : uuid:1faa9b0c-ad44-4fc7-b227-81709cd6a68b
Instance ID                     : uuid:62f2b61c-8f84-49cb-9d65-1db3c1d3ea56
Page Mode                       : UseOutlines
Page Count                      : 472

EXIF Metadata provided by EXIF.tools

Ford 2014 F 150 Owners Manual

2014-Ford-Ford-F-150-Owners-Manual-version-3_om_EN-US_03_2014 2014 Ford F-150 Maintenance Schedule | SERVICE MANUAL OWNERS

Navigation menu

Versions of this User Manual:

Views

Navigation