Foxpro 650 JD1 Transmitter User Manual

Foxpro Inc JD1 Transmitter Jack Daddyx

a href="https://usermanual.wiki/Foxpro" itemprop="url"> Foxpro >

User Manual

  FOXPRO Jack Daddy Operation Instructions To avoid personal injury and prevent product damage, read all operating instructions and safety precautions prior to use. Please note that these instructions may be modified without notice. It is recommended to periodically check the instructions to be aware of any recent changes. Important Information FOXPRO®’s goal  is  to  provide  our  customers  with  the  highest  quality  products  in the industry. We take great pride in manufacturing our products in the USA. Please do not hesitate to contact us for assistance, comments or questions.  FOXPRO® Inc. 14 Fox Hollow Drive Lewistown, PA 17044 (717) 248-2507 Fax: (717) 247-3594  Hours of Operation Monday – Friday 8AM – 5PM EST  Contact Us Customer Service: (717) 248-2507 Toll Free Orders Only: 866-463-6977 General Inquiry E-mail: sales@gofoxpro.com         This  manual,  the  animal  sounds  stored  in  your  caller,  and  animal  sounds  purchased  from FOXPRO® Inc. for installation in your caller are protected by copyright.   Copyright ©℗ 2014 by FOXPRO® Inc. REV4 - Publication Date: September 10, 2014
2 Jack Daddy Requirements The Jack Daddy is shipped without batteries. The Jack Daddy requires 4 ‘AA’ batteries.    Installing batteries in the Jack Daddy 1. Access the battery compartment by removing the door on the back of the Jack Daddy. The door features a knurled thumbscrew for easy access.  2. After the door has been removed, locate the black plastic battery tray.  The tray is double-sided, providing spaces for 4 ‘AA’ batteries. The tray can be pulled directly out of the battery compartment. Remove the tray from the compartment. 3. Place the batteries into each battery cavity while observing polarity as indicated. 4. Place the battery tray back into the compartment 5. Secure the door back to the Jack Daddy. Jack Daddy Remote: Requirements The Jack Daddy Remote contains a single lithium coin cell battery (CR2032). To replace the battery, follow the instructions below: 1. Before attempting to replace the battery, it is crucial that you understand the risks of electrostatic discharge potentially harming the electronic board during battery replacement! Prior to replacing the battery, make sure that you are static free. You can touch your hand to a refrigerator door, oven housing, door knob, etc. If you have the ability to use a proper grounding wrist strap, please do so. 2. Carefully separate the Jack Daddy Remote into two halves. This can be accomplished with a flathead screwdriver or other comparable tool. 3. Locate the battery and carefully remove it from the board by sliding it out of the holder. Note battery orientation as you remove it as the new battery must go back in the same way. 4. Carefully slide the new battery into the holder. 5. Place the circuit board back inside the appropriate case half. 6. Line the two halves up together and snap them shut to form a single device once again. Setting Up the Jack Daddy The following instructions apply whether you are using the Jack Daddy as a standalone device or linked-up with a FOXPRO digital game call. Basic field deployment instructions: 1. Locate the mounting stake on the left side of the housing. The Jack Daddy sits upon this stake in the field.  2. Unscrew the mounting stake from the housing.  3. Screw the stake into the mounting point on the bottom of the Jack Daddy.
Download:
Mirror Download [FCC.gov]
Document ID2424579
Application IDyZ9zdIibJMyQnut0lT5hiw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize8.87kB (110905 bits)
Date Submitted2014-10-22 00:00:00
Date Available2014-10-22 00:00:00
Creation Date2014-09-10 07:43:19
Producing SoftwareGPL Ghostscript 8.15
Document Lastmod2014-09-10 07:43:19
Document TitleMicrosoft Word - Jack-Daddy.docx
Document CreatorPScript5.dll Version 5.2.2
Document Author: Joe
FCC ID Filing: C6M650

Navigation menu