Friedrich CP12C10 User Manual ROOM A/C Manuals And Guides L0608155

FRIEDRICH Air Conditioner Room (42) Manual L0608155 FRIEDRICH Air Conditioner Room (42) Owner's Manual, FRIEDRICH Air Conditioner Room (42) installation guides

User Manual: Friedrich CP12C10 CP12C10 FRIEDRICH ROOM A/C - Manuals and Guides View the owners manual for your FRIEDRICH ROOM A/C #CP12C10. Home:Heating & Cooling Parts:Friedrich Parts:Friedrich ROOM A/C Manual

Open the PDF directly: View PDF .
Page Count: 19

Download
Open PDF In Browser	View PDF

Room Air Conditioner
Installation and Operation
Manual

CP Line
115 Volts

• CP10

• CP12

Registering Your Room Air Conditioner
Model information can be found on the name plate located on the
side of the unit near the control panel. Please complete and mail
the owner registration card furnished with this product or register
on-line at www.friedrich.com
(USA only). For your future
convenience,
record the model information here.

MODEL

NUMBER

SERIAL

NUMBER

PURCHASE

DATE

Congratulations!
Friedrich.

Thank you for choosing

Your Friedrich unit is designed for
maximum comfort and quietness.

Table of Contents
Introduction .................................................................................. 2
Safety Precautions ....................................................................... 3
How to operate your Friedrich ................................................... 5
Adjusting the Air Flow Direction................................................. 6
Care and Maintenance ................................................................. 7
Hardware Location ....................................................................... 8
Installation

Instructions ........................................................ 14

Troubleshooting Tips ................................................................. 16
Warranty ...................................................................................... 17

Introduction
Before Operating Your Unit
Make sure the wiring is adequate for your unit.
If you have fuses, they should be of the time delay type. Before you install or relocate this unit, be sure that
the amperage rating of the circuit breaker or time delay fuse does not exceed the amp rating listed in figure 1.

DO NOT use an extension cord.
The cord provided will carry the proper amount of electrical power to the unit; an extension cord will not.

Make sure that the receptacle is compatible with the wall plug provided.
This insuresproper grounding. If you have a two-prong receptacle you will need to have the circuit replaced
by a certified electrician with a grounded circuit that meets all national and local codes and ordinances. You
must use the three-prong plug furnished with the air conditioner.

MODEL

CIRCUIT
RATING OR
TIME DELAY
FUSE

PLUG FACE

AMP

VOLT

NEMA NO.

15

125

5-15P

CPIO
CP12

@

Figure 1

For the Best Cooling Performance and Energy Efficiency
Keep the filter clean
Make sure that your air conditioner is always in top performing condition by cleaning the filter regularly.
Instructions for removing and cleaning the filter can be found on page 7.

Provide good airflow
Make sure that the airflow to and from the unit is clear. Your air conditioner puts the air out at the top of
the unit, and takes in air at the bottom. Airflow is critical for good operation. It is just as important on the
outside of the building that the airflow around the unit exterior is not blocked.

Unit Placement
If your air conditioner can be placed in a window or a wall that is shaded by a tree or another building, the
unit will operate even more efficiently. Using drapes or blinds on the sunny side of the dwelling will also
add to your unit's efficiency.

/nsu/ation
Good insulation will be a big help in maintaining desirable comfort levels. Doors should have weather
stripping. Be sure to caulk around doors and windows.

Safety Precautions
To prevent injury and property damage, follow these instructions.
• incorrect operation due to ignoring of instruction can cause harm or damage. The seriousness is classified
by the following indications.

f/_
k.

/_

WARNING
CAUTION

This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to
properties only.

J

• Meanings of symbols used in this manual are as shown below.

f
_.O

Q
@

Never Do This
Always Do This

(_
I_

• Otherwise, it will cause electric
shock or fire due to heat

WARNING}

• it will cause electric

shock or fire

due to heat generation.

generation.

• it will cause electric shock or fire.
• if the power cord is damaged, it must
be reptaced by the manufacturer or a
Friedrich-certified

• it will cause electric

shock or fire

due to heat generation.

®

1

• it will cause electric

shock.

service agent.

• This could lead to health probiems.

• They are sharp and may cause
an injury.

• Water may enter the unit and
degrade the insulation. It may
cause an electric shock.

• Since the fan rotates

• This could injure the pets
or plants.

• Do not use this air conditioner

speed during

at high

operation,

it may

cause an injury.

®
• It could cause dust to
accumulate on the heat
exchanger.

• It may cause a fire or
deformation
of the cabinet.

• Use caution when handling the
case. Grip it firmly and do not allow
it to slip while holding it.
• Use heavy gloves to handle
the case if necessary.
• DO NOT
allow the
case to slide
against
your skin!
Sharp
edges

to

preserve precision devices, food,
pets, plants, and art objects.
It may cause deterioration
of
quality, etc.

How to operate your Friedrich

•

Temp •

Fan Speed

Timer

_o

l/

il

(_

Control and Remote Control Operations
1. POWER
Operation begins when this button is pressed
and stops when you press the button again.
2. TEMPERATURE CONTROL
The thermostat monitors room temperature
to maintain the desired temperature.
The thermostat can be set between
60°F~86°F (16°C~30°C).
The unit takes an average of 30 minutes to
adjust the room temperature by I°F.
3. OPERATION MODE SELECTOR
Select cooling mode to cool the room.
Select Money Saver@mode for energy
saving operation.
Select fan mode for basic ventilating fan
operation.
Select dry mode for dry operation.

4. FAN SPEED SELECTOR
For increasedpower while cooling, select a
higher fan speed.
3 steps: High; Low; Med
5. ON/OFF TIMER
The timer can be set to start and stop the
unit in hourly increments (up to 12 hours).
6. REMOTE CONTROL SENSOR

Inserting the Remote Control Batteries
1. Push out the cover on the back
of the remote control with your
thumb
2. Pay attention to polarity and
insert two new AAA 1.5V
batteries.
3. Reattach the cover.

NOTE: Donotuserechargeable
batteries.Makesurethat
bothbatteries
arenew.
• In orderto preventdischarge,removethe batteriesfrom
theremotecontrolifthe air conditioneris notgoingto be
usedfor an extendedperiodof time
humidplaces.
Keepthe
To
maintain
remotecontrolawayfromextremelyhotor
optimaloperationof the remotecontrol,the
remotesensorshouldnotbe exposedto directsunlight.
• Theremotecontrolcanbe mountedon a wall usingthe
mountableholder.(Friedrich
doesnotprovidethis.)

Adjusting the Air Flow Direction
Vent Control
For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation.
OPEN the vent to discharge stale air.

*.uJ_'qp.

Part

-.

"" :_::--'.'."

NOTE : Before using the ventilation feature, position
the vent lever by pulling Part A out straight
and snapping it into place.

Adjusting the Air Flow Direction
Airflow can be adjustedby changing the directionof the air conditioner's louvers.
•Adjusting Horizontal Air Flow Direction
Adjusting the vertical louvers left and right will
change horizontal airflow.

• Adjusting VerticalAir Flow Direction
Adjusting the horizontal louver up and down will
change vertical airflow. The louver can be
adjusted by pressing in at the top or button of the
horizontal louver.

\

Adjusting horizontal air flow

Adjusting vertical air flow

• Recommended orientation of louvers
Adjust louvers to face upwards when cooling to maximize cooling efficiency.

\

Care and Maintenance
Turn the power off and unplug the power plug before cleaning the air conditioner.

Air Filter
The air filter behind the inlet grille should be checked and cleaned at least once every 2 weeks (or as
necessary) to maintain optimal performance of the air conditioner.

How to remove the air filter
1. The grille may be opened from the top for easy
maintenance after installation.
2. Open the inlet grille by pulling out on the exposed
door on the top of the unit (based on installation).
3. Pull the tab slightly to release the filter. Pull the
filter in the same direction as the opening.
4. Clean the filter with warm, soapy water.
5. Rinse off and gently shake off excess water from
the filter. Make sure filter is completely dry before
replacing it.

Drainage
The base pan may overflow due to high humidity. To drain
the excess water, remove the drain cap from the back of
the unit and secure the drainpipe.
When pressing the drainpipe into place, apply force in the
direction away from the fins to avoid injuring yourself.

Drain

pipe

_]___
Drain

cap

Hardware Location
Product Features
//_

CAUTION
This appliance should be installed in accordance with local and national wiring regulations. This
manual acts as a guide to help to explain product features.

®
@

©
®
©

®

Positioning the Power cord
You can choose between two methods below according to your window stool shape and preference.

• Fasten the stopper using 2 screw holes, and lead
out the power cord through slit "A".

Power

° Fasten the stopper using left screw hole, and rotate
properly to lead the power cord out through slit "B".

Power

How to Install the Unit
1. To prevent vibration and excess noise,
make sure the unit is installed securely
and firmly
2. Install the unit where the sunlight does not
shine directly on the unit.

Fence
Awning
Cooled

air

Heat

3. The outside of the cabinet must extend
outward for at least 12" and there should
be no obstacles, such as a fence or wall,
within 20" from the back of the cabinet, as
it will prevent heat radiation of the
condenser.
Restriction of outside air will greatly reduce
the cooling efficiency of the air conditioner.

CAUTION: All side louvers of the cabinet must remain exposed and unobstructed to the outside of the
structure.

4. Install the unit with a rear, downward slope, so the back is slightly lower than the front
(about 114"buble on a level). This will force condensation to flow to the outside.
5. Install the unit with the bottom about 30"~60'' above the floor level.

Window Requirements
NOTE: All supporting parts should be secured to firm wood, masonry, or metal.
• This unit is designed for installation in standard
double hung windows with actual opening widths
from 27" to 39".
• The top and bottom window sash must open
sufficiently to allow a clear vertical opening of 16"
from the bottom of the upper sash to the window
stool.

ili27,,
to39,,
...........
. 16 min . Stool
/w@Trame
cur_an) ,, Jl ............

I

iL"i\

5,1

Offset

:

Interior wall ".]" .... L"X,Exterior
, 23 5/8 min. ,/
I (Without
frame
curtain)/

Installation Kit Contents
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13

NAME OF PARTS
FRAME CURTAIN
SILL SUPPORT
BOLT
NUT
SCREW (TYPE A)
SCREW (TYPE B)
SCREW (TYPE C)
FOAM-STRIP
UPPER GUIDE
FOAM-PE
FRAME GUIDE
WINDOW LOCKING BRACKET
FOAM-PE

Q'TY
2
2
2
2
16
3
5
1
1
1
2
1
1

Suggested Tool Requirements
J

SCREWDRIVER(+,

-), RULER, KNIFE, HAMMER, PENCIL, LEVEL

PREPARATION OF CHASSIS
1. Remove the screws which fasten the cabinet at both
sides and at the back.(4 total)

Shipping
Screws

.-....

2. Slide the unit from the cabinet by gripping the base pan
handle and pulling forward while bracing the cabinet.
3. Cut the window sash seal to the proper length.
Peel off the backing and attach the Foam-PE @ to the
underside of the window sash.
4. Remove the backing from the top upper guide Foam-PE
® and attach it to the bottom of the Upper Guide ®.
5. Attach the upper guide onto the top of the cabinet with 3
Type A screws ®.
6. Insert the Frame Guides ® into the bottom of the cabinet.
7. Insert the Frame Curtain O into the Upper Guide (_ and
Frame Guides @.
8. Fasten the curtains to the unit with 4-Type
A screws _).
(Type A)d

)(Type A)

Cabinet Installation
1. Open the window. Mark a line on center of the
window stool.
Carefully place the cabinet on the window
stool and align the center mark on the bottom
front with the center line marked in the
window stool.

Upper

Guide

Window stool
Front Angle
Fig. 1

2. Pull the bottom window sash down behind the
Upper Guide until they meets•

Window

Sash

Upper

guide

\\

NOTE: Do not pull the window sash down so
tightly that the movement of Frame
Curtain (_ is restricted.

Foam-pe
Cabinet
Frame

-- -......

/

Curtain
Foam-pe

Fig. 2
3. Loosely assemble the Sill Support Q using
the parts in Fig. 3.

INDOOR_

-

_

,OUTDOOR
•

port@

Bolt@
Fig. 3

4. Select the position that will place the Sill
Support ® near the outer most point on sill
(See Fig. 4)
NOTE: Be careful when you install the cabinet
(Frame Guides @ are broken easily).
5. Attach the Sill Support _ to the cabinet track
hole in relation to the selected position using
2 -type A ® screws in each support
(See Fig. 4).

Screw(Type
Frame

A)

Guide@

LL___\

Fig. 4

6. The cabinet should be installed with a very slight
tilt (about 1/2") downward toward the outside
(See Fig. 5).
Adjust the bolt and the nut of Sill Support ® for
balancing the cabinet.

Screw(Type

/I

B) (._

J

LL_ ...., •
_k_..e__

\

{

u

7. Attach the cabinet to the window stool by driving
the screws ® [Type B: Length 16mm (518inch)
and below.] through the front angle into window
stool.
8. Pull each Frame Curtain _ to each window
sash track, and repeat step 2.

........
Support@

.S_ash track

F,oot n0,e
Screw(Type

B)

Sill Support
9. Attach each Frame Curtain •

Fig. 5

to the window

sash using screws _ (Type C). (See Fig. 6)

CAUTION: Do not drill a hole in the bottom pan.
The unit is designed to operate with
approximately 1/2" of water in bottom
of pan.
There is no need to add water if the
pan is dry.

Type C

Fig. 6

10. Slide the unit into the cabinet. (See Fig. 7)
CAUTION: For security purpose, reinstall the 2
screws (Type A) at cabinet's side, that
were removed in step 1 on page 10.

Screw(Type

A)
Screw
(Type

A)

Fig. 7

11. Cut the Foam-Strip ® to the proper length
(window width) and insert between the upper
window sash and the lower window sash.
(See Fig. 8)
Fig. 8

12.Attach
theWindow
Locking
Bracket
@witha TypeC
screw@.(SeeFig.9)

Window

locking

bracket

Fig. 9

13.Attach
thefrontgrilletothecabinet
byinserting
the
tabsonthegrilleintothetabsonthefrontofthe
cabinet.
Pushthegrilleinuntilitsnapsintoplace.(See
Fig.10)
Fig. 10

14.Pulldowntheinletgrilleandsecure
itwithaTypeA
screw® through
thefrontgrille.(SeeFig.11)
15.Window installation of room air conditioner is now
completed, See ELECTRICAL DATA for
inserting power cord to electrical outlet.

Fig. 11

Installation Instructions
Read these instructions completely and carefully.

Tools You Will Need
[] Phillips-head screwdriver
[] Flat-blade screwdriver
[] Ruler or tape measure

[] Scissors or knife
[] Pencil
[] Level
[] Hammer

Before You Begin
NOTE TO INSTALLER: Leave these
instructions
with the air conditioner after
installationis completed.
NOTE TO CONSUMER: Keep this Installation
and Operation Manual for future use.

Important notes:
It is recommended that proper attire be worn
during installation.
For personal safety, this air conditioner must
be properly grounded.
It is important to have the wall outlet and circuit
checked by a qualified electrician if there is any
doubt as to whether a proper ground exists.

CAUTION:
Do not under any circumstances,cut or remove
the third (ground) prong from the power cord.
Do not change the plug on the power cord of
this air conditioner.
Aluminum house wiring may present special
problems-consult a qualified electrician.

Electrical safety
Electrical

Data

115V~

F
\=j

Power cord may include a current interrupter device.
A test and reset button is provided on the plug case.
The device should be tested on a periodic basis by first pressing
the TEST button and then the RESET button.
If the TEST button does not trip or if the RESET button will not
stay engaged, discontinue use of the air conditioner and contact
a qualified service technician.

Use Wall Receptacle

©
Standard 125V, 3-wire grounding
receptacle rated 15A, 125V AC

Power Supply

Use 15 AMR time
delay fuse or 15 AMR
circuit breaker.

Use of extension cords
Because of potential safety hazards, we strongly discourage the use of an extension cord.
However, if you wish to use an extension cord, use a CSA certified/UL-listed3-wire (grounding)
extension cord, rated 15A,125V.
All wiring should be made in accordance with local electrical codes and regulations.

I M[o_i[*]q
Aluminum house wiring may pose special problems. Consult a qualified electrician.

ELECTRICAL

SAFETY

IMPORTTANT GROUNDING INSTRUCTIONS
Air conditioner has a three-prong grounding plug on its power supply cord, which must be
plugged into properly grounded three-prong wall receptacle for your protection against possible
shock hazard.

Troubleshooting

Tips

Troubleshooting
Tips savetimeand money!Reviewthe chartbelowfirstand youmaynot needto callfor service.

Normal Operation
_

, You may hear a pinging noise caused by water being picked up and thrown against the condenser
on rainy days or when the humidity is high. This design feature helps remove moisture and improve
efficiency.
• You may hear the thermostat click when the compressor cycles on and off.
• Water will collect in the base pan during high humidity or on rainy days. The water may overflow and
drip from the outdoor side of the unit.
• The fan may run even when the compressor does not.
• Your air conditioner is designed to cool in warm weather when the outside temperature is above
60°F(16°C) and below 115°F(46°C).

Abnormal Operation

• Make sure the air conditioner plug is pushed
completely into the outlet.
• Check the house fuse/circuit breaker box and

Air conditioner
does not start

replace the fuse or reset the breaker.
• If power failure occurs, turn the mode control to Off.
When power is restored, wait 3 minutes to restart the
air conditioner to prevent tripping of the compressor
overload.
• Press the RESET button located on the power
cord plug. If the RESET button will not stay eng
aged, discontinue use of the air conditioner and
contact a qualified service technician.
• Make sure there are no curtains, blinds, or furniture
blocking the front of the air conditioner.
• Push temperature setting button to coolest
temperature setting of 60°F.
• Clean the filter at least every 2 weeks.
See the operating instructions section.

Air conditioner
does not cool as it
should

• When the air conditioner is first turned on you need
to allow time for the room to cool down.
• Check for open furnace floor registers and cold air
returns.
• Set the air conditioner's vent to the closed position.
• See Air Conditioner Freezing Up below.

Air conditioner
freezing up

i

iiiiiiiiiii : ii i i i !i ! i 'i

• Set the mode control on high fan until the ice thaws
out.

FRIEDRICH AIR CONDITIONING
Post Office

Box 1540

(210)

• San Antonio,

357-4400

• FAX (210)

CO.

Texas 78295-1540
357-4490

ROOM AIR CONDITIONERS
LIMITED WARRANTY
FIRST YEAR
ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from date of
original purchase, FRIEDRICH will repair the product at no charge, provided room air conditioner is reasonably accessible for service.
Any additional labor cost for removing inaccessible units and/or charges for mileage related to travel by a Service Agency that exceeds
25 miles one way will be the responsibility of the owner. This remedy is expressly agreed to be the exclusive remedy within twelve
months from the date of the original purchase.

SECOND THROUGHFIFTHYEAR
SEALED REFRIGERANT SYSTEM: If the sealed refrigeration system (defined for this purpose as the compressor, condenser coil,
evaporator coil, reversing valve, check valve, capillary, filter drier, and all interconnecting tubing) supplied by FRIEDRICH in your Room
Air Conditioner fails because of a defect in workmanship or material within sixty months from date of purchase, FRIEDRICH will pay a
labor allowance and parts necessary to repair the Sealed Refrigeration System; PROVIDED FRIEDRICH will not pay the cost of diagnosis
of the problem, removal, freight charges and transportation of the air conditioner to and from the Service Agency, and the reinstallation
charges associated with repair of the Sealed Refrigeration System. All such cost will be the sole responsibility of the owner, This remedy
is expressly agreed to be the exclusive remedy within sixty months from the date of the original purchase,
APPLICABILITY
AND LIMITATIONS: This warranty is applicable only to units retained within the Fifty States of the U.S.A.
Columbia, and Canada, This warranty is not applicable to:

District of

1.
2.

Air filters or fuses.
Products on which the model and serial numbers have been removed,

3.

Products which have defects or damage which results from improper installation, wiring, electrical current characteristics, or
maintenance; or caused by accident, misuse or abuse, fire, flood, alterations and/or misapplication of the product and/or units
installed in a corrosive atmosphere, default or delay in performance caused by war, government restrictions or restraints, strikes,
material shot[ages beyond the control of FRIEDRICH, or acts of God.

OBTAINING WARRANTY PERFORMANCE:
Service will be provided by the FRIEDRICH Authorized Dealer or Service Organization
in your area, They are listed in the Yellow Pages.If assistance is required in obtaining warranty performance, write to: Room Air Conditioner
Service Manager, Friedrich Air Conditioning Co., p.o. Box 1540, San Antonio, TX 78295-1540.
LIMITATIONS: THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES. Anything in the warranty notwithstanding,
ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND/OR MERCHANTABILITY
SHALL BE LIMITED TO
THE DURATION OF THIS EXPRESS WARRANTY. MANUFACTURER EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY
FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY.
NOTE: Some states do not allow limitations on how long an implied warranty lasts,or de not allow the limitation or exclusion of consequential
or incidental damages,so the foregoing exclusions and limitations may not apply to you.
OTHER: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
PROOF OF PURCHASE:

Owner must provide proof of purchase in order to receive any warranty related services,

All service calls for explaining the operation of this product will be the sole responsibility
All warranty service must be provided by an Authorized
repairs being made.

FRIEDRICH

Service

Agency,

of the consumer.
unless authorized

by FRIEDRICH

prior to

In case of questions regarding the provisions of this warranty, the English version will govern,

Revised 08/01

Frlelrlrlcn_"
-- " -FRIEDRICH

AIR CONDITIONING

Visit our web

Post Office

Box 1540

• 4200

CO.

site at www.friedrich.com

N. Pan Am Expressway

• (210) 357-4400

• FAX (210)

• San Antonio,

Texas

78295-1540

357-4490
P/NO.:

3828A21016D



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 19
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Wed Aug 15 06:16:33 2007
Author                          : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools