Frigidaire BBBD2432KB0 User Manual DISHWASHER Manuals And Guides L0410283
FRIGIDAIRE Dishwasher Manual L0410283 FRIGIDAIRE Dishwasher Owner's Manual, FRIGIDAIRE Dishwasher installation guides
User Manual: Frigidaire BBBD2432KB0 BBBD2432KB0 FRIGIDAIRE DISHWASHER - Manuals and Guides View the owners manual for your FRIGIDAIRE DISHWASHER #BBBD2432KB0. Home:Kitchen Appliance Parts:Frigidaire Parts:Frigidaire DISHWASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dishwasher Parts You Will Need* (Not#ncluded) • • • • Installation Instructions IMPORTANT: Drain Hose Clamp, 1W' Diameter Elbow, 90 ° with a 3/d' National Pipe Thread Conduit Connector Wire Nuts, two (2) for 12-14 gauge wire Disconnect power before starting installation. Electrical lYf:l 1! at: 1. ; If required: Available • "Y" Branch Tailpiece and Connector Kit (See Step 4) • Air Gap Kit (See Step 4) • Fasteners for floor Plumbing Supply Store Observe all local codes and ordinances for Plumbing Supply Store Hardware Store electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury. Electric Shock Hazard anchoring (See Step 9) 1. Make sure your location has the right drain, water, and electrical outlets to make the connections. Do not install unit under a cooktop range, Damage to plastic tub will occur, 2. Note the locations of electrical supply and dishwasher's electrical junction box on right underside of unit behind kickplate assembly. See Figure 3. 3. Cut access hole in shaded area shown in Figure 2. 4. Pull electrical cable through hole into installation area. -_ f 1. Determine where you will connect to hot water supply. Review Figure 3 and note the location of water inlet valve. Examine dishwasher and locate connections. • Locate dishwasher where there is easy access to drain, water, and electrical lines. The best location is on either side of the kitchen sink for access to existing plumbing and ease in loading dishes. See Step 4. • , 90°---_ © See Step 4. 24 '''_ rain. /-- Electrical, water, and drain lines must be confined to shaded area. Do not use the furnished drain hose or a rubber garden hose for the water supply line. Either of these hoses can burst. Flooding may occur and cause property damage. • Kinked water or drain hoses can cause problems. See Step 6. • Dishwashers need to be connected to a hot water supply with enough water pressure to insure an adequate fill. See Steps 4 and 7. Printed in U.S.A. 154427301 (04/07) • @ | 8 _ , i_ %' . f 3. Flgut_ installing 2. Do not use dishwasher until completely installed. 2. Failure to follow this warning can result in serious injury. It is not necessary to remove the outer door for installation. However, you might find it more convenient to do so. You can find directions for removing door in Step 10. Kicl_plate Drill, Electric _pamte Trap NOTE: If dishwasher is installed at end of a cabinet line, sides and back must be fully enclosed. NOTE: You can order a Cabinet Seal Kit (Kit # 154528701) by contacting your dealer or parts supplier. This kit provides a seal between the unit and cabinets once installation is complete. Figure 4 4. Cut water access hole in shaded area in Figure 2. 5. Route water supply line into installation area. IMPORTANT: Incoming hot water temperature should least 120°F (49°C). Water pressure should be between 20-120 psi. Drain 1. Review Figures 5 and 6 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. IMPORTANT: Do not cross drain, water, and electrical lines in front of dishwasher motor or frame. Locating the Connections 1. Review dimensions in Figure 3 to locate dishwasher's water, and electrical connections. 2. All connections must be made in shaded area in Figure 2. drain, 3 Sink at RlghtSMe 2" Drain Hose Hole 49 _/4" I,_ 23_/s " I Door in opon posltion l/an. 3. Locate water inlet valve behind kickplate on bottom left underside of unit. The valve has a 3/s"NPT female fitting. Tape, Electrical or Duct Tape, Measuring 4. Wrap 90 ° elbow (not included) with pipe thread tape (or apply joint compound) and thread it into water inlet valve. Wire Stripper or Utility Knife Wrench, Hex-end 5. Tighten elbow with a wrench, leaving elbow pointing toward rear of unit. To prevent bending of bracket or breaking of valve, a void overtightening. 33/+,, From rear to center of water lnlet valve. From #oor to water inlet valve. Junction Box (not visible) . 5. Before cutting drain hose access, check both sides of selected area to avoid interference. Cut a 2" diameter hole in shaded area shown in Figure 2. 6. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. be at Entry Must be Above i_ Sink at Right Flgnre 71b) (This kit is included on select models). Water Inlet Valve Saw, Keyhole or V2", 1V2" to 2" Hole Cutters Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred) r .oekout 2" Drain Hose Hole Electrical, water, and drain lines must be confined to shaded areas in Figure 2. Front Fl_u/_ n connection. Through Floor into _in Safety Glasses Wrenches, 2 Adjustable (for copper tubing) or 2 Pipe wrenches (for iron pipe plumbing) Cot [or 3./# Electric Shock Hazard F_ure Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) Pliers Drain Hose ve Driver, Socket 3116",V4",5/_6" Flaring Tool / Tube Cutter (for copper tubing) Flashlight Level _ltsdisposer Inlet filling. Alternate Drain Figure5 Tools and Materials Needed for Installation / Drain Air Gap FdcAplateAssembly Adjustable Toeplate (Insulation avdilable somemodols) connection. / •Largerend ofhose 71a) 2 Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock. Tilt and pull forward to remove. See Figure 1. . ...... F_ure II dishwasher. See Step 9. Remove two (2) screws at front of the kickplate assembly using a #2 Phillips screw driver. NOTE: Do not push down on open door. Cutfor_/, IMPORTANT: Drain, water, and electrical lines should be roughed-in before going any further. For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher. Tip Over Hazard / Remove any carpet from area to provide motor clearance. Floor should be flat and free of any obstruction. dishwasher. 1. Drain Motor End Flush water line prior to making the final connection to prevent clogging of dishwasher's filter screen. See Step 7. • Anchorthe before Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Copper tubing must have a minimum _/8"OD. High-pressure and high-temperature rated plastic tubing with a minimum inner diameter of V4"may be used. A shut-off valve installed outside dishwasher cabinet is best. See Figure 4. IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance to open door. • The dishwasher will look, sound, and perform best when properly leveled. See Step 5. (NOTE: If levelers are removed during installation, make sure the floor is flat and free of any obstruction.) Read all instructions Be sure water inlet valve is )rotected from freezing. If valve freezes and ruptures, flooding may occur. Each home installation differs. You will need additional parts listed above to complete your installation. See Steps 4 and 7. • If you connect to a disposer, the large end of drain hose will fit. Figure 7(a). The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. See Figure 7(b). drain hose will be connected to a food disposer for the first time, knock out plug located inside disposer inlet. See Steps 4 and 6. OWNER: Read your dishwasher Use and Care Manual. It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher. 4. Property Damage 90 ° __ • A 15-20 amp, grounded, 120 volt AC only, electrical supply is required. See Steps 4 and 8. INSTALLER: Leave Installation Instructions with owner. If you connect to a sink trap, local codes may require you to install an air gap kit, not included. The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 6. An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary). © Electrical, water, and drain connections are not the same for all age, brands, or models of dishwashers. Check the location and length of home utilities. See Step 4. • If dishwasher 3. j 34,'/_"min. • i Water Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. Air Gap The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 5. . Measure height of cabinet opening from underside of countertop to floor. Check chart for height opening and suggested adjustment. Electrical Supply Floor Anchoring 1. Remove junction box cover and pull house wiring into junction box. See Figures 12 and 13. This procedure is difficult and should be used only if countertop mounting brackets cannot be used. 2. Use a UL listed conduit connector, not included, at box to stabilize wiring. IMPORTANT: dishwasher's , 5. 1. Screw 1/4"lag screws, not included, through holes provided in frame rail. See Figure 15. 2. Use expansion fasteners if floor is concrete. Place door where it will not get scratched or damaged while completing installation. When ready to replace door, fit the slots on each side of top door edge over the tabs on the metal liner. Push on sides to insure the door is fiat. Push up from bottom until there is no gap between door and console. See Figure 16c. Be sure electrical cable is not routed behind motor. Use'/4 "/.agscrews (not includ_d) Leg Leveler Adjustment Height of Cabinet Opening Chart Liner Number of Turns to Adjust Levelers 34" (86.4cm) 0 34W' (86.7cm) 2 345/16"(87.2cm) 6 341/2" (87.6cm) 9 Figure 15 Figure I0 The drain hose loop must be at least 32" !_ to insure proper drainage. from the lloor Wall For additional height add shims under levelers. . 3. Move dishwasher to front of installation area. Junction Box (in place) Loosen the front and rear leveling legs by turning counterclockwise. Refer to chart for number of turns. See Figure 8. Front levelers should allow 1/4"below underside of countertop. J Door Side View Note: If mounting your dishwasher to the countertop or to the floor is not a desirable option, you can order the side mount kit, 154477201, by contacting your dealer or parts supplier. This allows you to install the dishwasher by securing it to the cabinets or partitions on either side of the unit. The kit utilizes the front frame of the dishwasher to secure the unit to the cabinet or partitions. Appearance of console and door may vary from your model. Property Damage 6. Do not solder within 6" of the water inlet valve. Damage to the plastic parts in the valve may occur. PTgure 12 Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur. ///i! . Be sure the dishwasher is placed where the water inlet valve will be kept from freezing. If the valve freezes, it may rupture and flooding may occur. 4. Water Line 1. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open valve for a few seconds and let water drain into a pan. Turn off water supply at shut-off valve. Inside junction box, attach ground wire under head of grounding screw and tighten. See Figure 13. Connect incoming black lead to dishwasher's black lead and incoming white lead to dishwasher's white lead with wire nuts or other suitable connectors, not included. Wire nuts should be tight. Conduit Connector Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Ground Wire Before starting the dishwasher, check these items: Failure to follow this warning could result in death or serious injury. Figure II 4. 5. 6. If levelers have to be removed, make sure floor is free of obstructions. Cut Hazard Place dishwasher inside cabinet area so that it is centered in opening. Use caution when moving dishwasher to prevent damage to dishwasher, floor, and cabinets. Through Cabinet \ Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. White Wire to White Wire (Neutral) Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 9a. Hgure 9a 7. 8. Hgare 9b Check that dishwasher is level from front to back by placing level on side of opened door. See Figure 9b. 2. Route water line to water inlet valve as shown in Figure 11. 3. While firmly pulling water supply line into 90 ° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. 4. Turn on water supply and check for leaks. 5. If water inlet valve clogs, make sure water supply is off. Remove four (4) screws at inlet end of valve and clean filter screen. 5. Replace junction box cover. See Figure 13. The dishwasher door panel can be customized to match wood cabinets. This will require a kit that includes a mid-door with side and bottom trim, heavy-duty door springs and instructions. 1. Adjust levelers (see Step 5) so mounting brackets touch underside of countertop. IMPORTANT: Dishwasher must rest on floor--do not hang from countertop. See Figure 14. 2. Screw mounting brackets firmly to countertop using screws provided in literature packet. 3. Open and close dishwasher door slowly. If door hits mounting bracket screw heads, adjust front levelers. . Unlatch and open door. Using a Phillips head screw driver, remove two (2) screws from inner door. Save screws to reassemble. See Figure 16a. Figure 1. Pull out unit and check to see if drain hose is correctly attached to the drain pump assembly, tf drain hose is not attached to drain pump, follow the instruction sheet (included with drain hose) on how to correctly install the drain hose to the drain pump assembly. 2. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. Close and latch door while holding both sides. 3. Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. 4. Be sure unit does not rest on drain hose. It should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. See Figure 10. The dishwasher must be connected to a grounded metal, permanent wiring system. The equipment-grounding conductor must be run with the circuit conductors and connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. Place one hand on each side of door and Failure to follow these instructions could result in death or serious injury. Water and drain lines have no kinks. _1 Wiring connections to junction box are tight. Refer to Step 10, numbers 5 and 6, for replacing outer door. 2. Adjust door springs to balance weight of door. A correct spring setting allows door to remain horizontal in opened position, yet will rise to close with slight lift of finger. 3. If necessary, increase tension by moving springs to a hole toward rear of unit or decrease by moving them toward front. See Figure 17. pull down at top approximately V4". Pull entire door Head Screws i Check water connections again for leaks. • ?!±l ;! ;!1 I 5 #8 x /8 Turn electrical supply on. At pump-out, make sure all water is pumped out. assembly toward you to remove. See Figure 16b. Use Phillips 17 At first fill, make sure water completely covers filter surface. (Motor pump sound may be heard before water enters unit). iii i (included in the literature packet). All wiring connections must be enclosed in the junction box. This unit has copper lead wires. Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. _1 Operate the machine through at least one fill and pump-out, checking the following items: Figure ! 6b , Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes. Open and close door to make sure it does not hit surrounding cabinet or countertop. 1. 4. at fuse Do not connect the dishwasher to the power supply until the appliance is permanently grounded. _1 Move springs toward rear of dlsgwasher to increase tension. Electric Shock Hazard Make sure electrical power has been disconnected box or circuit breaker box. Dishwasher is level and securely fastened. i 6a Plumbing material and drain hose must not come in contact with wiring or electrical components. Failure to follow this warning could result in personal injury from exposed wiring. _1 F/_are Note: Open and close door to make sure it does not hit surrounding cabinets or countertop. Electric Shock Hazard All packing materials and consumer literature have been removed from u nit. To Remove and Replace Outer Door . Countertop Anchoring Adjust levelers up or down until dishwasher is level. _1 Joints are free of leaks. Kits are available from your dealer or parts supplier. The dishwasher must be secured to keep it from tilting when door is opened. Choose one of the methods described below to secure unit. Drain hose is assembled to drain pump. Replacing Door To Install a Custom Wood Panel Through Floor _1 Water supply is turned on. Failure to follow this warning may result in injury. Black Wire to Black Wire (Hot) S Unlatch door and open while supporting outer door on both sides at bottom to keep in place. Align screw holes and replace screws. Appearance of console and door may vary from your model. Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. I Failure to follow this warning could result in electric shock.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Sun Jun 07 04:14:29 2009 Author : Title : Subject :EXIF Metadata provided by EXIF.tools