Frigidaire BGGF3031KBC User Manual GAS RANGE Manuals And Guides 1408061L

User Manual: Frigidaire BGGF3031KBC BGGF3031KBC FRIGIDAIRE GAS RANGE - Manuals and Guides View the owners manual for your FRIGIDAIRE GAS RANGE #BGGF3031KBC. Home:Kitchen Appliance Parts:Frigidaire Parts:Frigidaire GAS RANGE Manual

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

GRLP3 CONVERSION

INSTALLATION

KiT APPLiCATiON

AND SERVICE

iNSTRUCTiONS

MUST BE PERFORMED

A QUALIFIED
INSTALLER.
IMPORTANT:
SAVE FOR LOCAL ELECTRICAL
INSPECTOR'S
USE.
READ AND SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
I_
This conversion kit must be installed by a qualified service technician in accordance with the
manufacturer's
instructions and all applicable codes and requirements
of the authority having jurisdiction.
Failure to follow instructions may result in fire, explosion or production of carbon monoxide causing property
damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of
this kit. The installation is not proper and complete until the operation of the converted appliance is checked as
specified in the manufacturer's
instructions supplied with this kit.
Before proceeding with the conversion, shut off the gas supply and disconnect the electrical
power to the range. Be sure both power supplies are off before installing the conversion kit. Failure to do so
could cause serious bodily injury.
IMPORTANT:
Do not attempt to use this conVersion
kit on products for which itis not specifically
designated:
Consult
the product installation manual or parts list to determine
the correct conversion
kit number
Tools

prior to use.

Required

for

L.P. Conversion"

(A) 3/8", 1/2" and 5/8" Open End Wrench, (B) #1 Square Tip Screwdriver,
(C) 1/8" Wide Flat Blade Screwdriver,
(D) 7rnm & 3/16" Nutdriver

How
1.

to Convert
Convert

the

Range

Pressure

for

use with

LP/Propane

A--_

B--_

C-_

D-__

Gas

Regulator

To access the gas regulator, remove the storage drawer or warmer drawer. If equipped with a storage drawer, open and remove the drawer completely. For
models equipped with a front panel, remove the front panel and skip steps b & c below. For models equipped with warmer drawer, follow all the instructions
below to remove the warmer drawer. NOTE: DO NOT ATTEMPT TO CONVERT MODELS THAT FEATURE A LOWER OVEN.

a.
b.
c.

_
Electrical Shock Hazard can occur and result in serious injury or death. Disconnect electrical power to the range
before removing the warmer drawer for servicing.
Locate glide lever on each side of drawer, pull up on the left glide lever and push down on the right glide lever (See Fig. 1).
Pull the drawer away from the range (See Fig. 2).
........

_ ,:;:,2_ ...................

_,_:: _ .........

Pull up with finger

Left Glide

Fig. 2

[]
Push down with finger

Fig. 1

p/n 316417518

rev F (1008)

( Continued

on following

page )

After removing the drawer identify which type of regulator
is installed on the range by comparing
the photos below. Follow the appropriate
conversion
instructions found on the following
pages.
Hex Shaped Cap

Plastic Dust Protector I

Aluminum Top I

Fig. 3 Aluminum Regulator

iNSTRUCTiONS
FOR CONVERTING
ALUMINUM
REGULATOR:
If the regulator has an aluminum top as pictured in Fig. 3 convert the regulator in the following
A. Remove the regulator access cover if equipped. Do not remove the Pressure Regulator
B. Unscrew the hex shaped cap and turn it over to access the conversion plug inside the cap.
Do not remove the spring from the regulator.
C. Rotate the plug 90 degrees in either direction to align the tabs on the plug with the notches
Lift the plug out of the cap.
D. Turn the plug over so that the
nib on then end of the cap faces
out and re insert into the cap.
Rotate the plug 90 degrees in
either direction to lock it into the
cap (Fig C)
E. Reinstall the cap and plug
securely onto the regulator.
F. Attach the LP conversion label
as illustrated on page 8 then
complete the remaining steps in
the instructions provided with
the LP kit.

CONVERSION

PLUG

[

UNLOCK

Fig. 4 Steel Top Regulator

manner:
or allow it to turn.
(Fig A)
in the cap. (Fig. B)

REINSTALL PLUG
WITH NIB POINTING UP

INSTRUCTIONS
FOR CONVERTING
STEEL TOP REGULATOR:
If the regulator has a steel top as pictured in Fig. 4 above
convert the regulator in the following manner:
A. Remove the regulator access cover if equipped. Do not remove the Pressure Regulator or allow it to turn.
B. Remove the plastic dust protector from the cap (Fig 5). Using a 5/8" wrench, unscrew the cap from the pressure regulator (Fig 6).
Do not remove the spring from the regulator.
C. Turn the cap over so the hollow end faces outward. Place the solid end of the cap into the loop end of the dust protector
(See Fig. 7).
D. Replace the cap on the regulator with the hollow end facing out (Fig 8). Do not over tighten the cap. Snap the dust protector over
the regulator cap.
E. Attach the LP conversion label as illustrated on page 8 then complete the remaining steps in the instructions provided with the LP
kit.

NOTE: The pressure regulator cap
may be made d brass or aluminum
depending on the age of the
product. The conversion process is
the same for both types of caps.

2.Convert

Surface Burners

for use with LP/Propane Gas

This conversion kit contains multiple gas orifices for converting different styles of sealed gas surface burners. Determine
which style of gas surface burner is being converted and select the proper orifice from the designated orifice pack for that
jspecific burner styJe and size.
lSave the natural gas orifices removed from the appliance for possible future conversions to natural gas.
BURNER
STYLE #1 (Non Mounted Burner)
This burner style is not secured to the cooktop with screws and the burner head
can be lifted off the cooktop to access the orifice holder and orifice. The orifice

No MountingScrews

holder for this style of burner passes through a circular cut out in the cooktop as

seen style
This
in theof photo.
burner will use the orifices contained in the main envelope of the

'_
_

_+_

converting this burner style.
BURNER
STYLE #2 (Screw Mounted Burner)
This burner is secured to the cooktop surface by two screws as seen in the photo.
The screw heads may be different than those illustrated. When the burner is
removed the orifice holder cutout in the cooktop can be seen to have an irregular
elongated shape. The mounting screw sockets for the burner head are also
visible. This style of burner will use the orifices contained in the separate smaller
envelope found inside the main envelope of the LP kit # GRLP3. This envelope
will be labeled " SCREW MOUNTED BURNER LP KIT". Follow the instructions on
page 4 when converting this burner style.
BURNER
STYLE #3 (Screw Mounted Burner)
This burner can be identified by the two piece cap as seen in the photo. It is
secured to the cooktop surface by two screws. The screw heads may be different
than those illustrated. When the burner is removed three orifice openings can
be seen in the cooktop. This style of burner will use the orifices contained in the
separate smaller envelope found inside the main envelope of the LP kit # GRLP3.
This envelope will be labeled " SCREW MOUNTED BURNER LP KIT". Follow the
instructions on page 5 when converting this burner style.

BURNER
Burner

Secured

With

STYLE #1

Screws

Elongated

BURNER
Burner

Secured

With

Screws

BURNER

STYLE

Bottom

View

Top View

Bottom View

INSTRUCTIONS
Unlike the standard gas range,
THIS COOKTOP IS NOT REMOVABLE.
Do not attempt to remove this cooktop.

Use caution when replacing each burner cap
so the electrode is not damaged.

Example

Oval Burner

Top View

BURNER STYLE #1 CONVERSION

Opening

OVAL BURNERS
There are currently two different oval surface burners used and each one requires
a different LP orifice. Both burners are rated 9500 BTU and are very similar in
appearance when the burner caps are in place. Use the photos at right to identify
which oval burner is on your range and use the appropriate orifice for that burner
when converting.
Oval Burner A - Use orifice size .89 from the main envelope. The orifice holder
for this burner will have the circular cooktop opening as seen in Burner Style #1.
Oval Burner B - Use orifice size .93 from envelope labeled " SCREW MOUNTED
BURNER LP KIT". The orifice holder for this burner will have the elongated
cooktop opening as seen in Burner Style #2.
NOTE: Some ranges may include multiple burner styles. When this is
encountered
use the appropriate
orifice for each burner styJe and size.

Cooktop

of Burner Assembly

B = 9.5k
D=12k
E = 14 or 14,2k

A= 5k
B = 9.5k

B = 9.5k
(some models)

letter
located

f__

inside
Burner
Head

_._
_
_//_

_=.._Round

,
J=l_:_;_ _,_._

B .....
Head i i_':g&

Or Oval Center

Burner --

:!i

theMatch
letter
stamped
(
t
j) 1\
_r_
on Burner
\
_>
Skirt with
_Bumer
Skirt
Burner
Head
_ .........
and

Burner

elect ;ode
J

B = 9.5k

B =
D =
E =
F=

9.5k
12k
14 or 14.2k
16 or 16.2

B _=&,Sk

Cap

( Continued

on page 4 )

( Continued from page 3 )

Burner

Unlike the standard gas range
THIS COOKTOP IS NOT REMOVABLE.
Do not attempt
to remove this cooktop.

Burner
Head

7mm
Nut
Driver

GAS SURFACE BURNER ORIFICE DATA CHART (Burner Style #1)
BTU Rating / Natural
Natural

Gas

Gas Orifice

LP Gas Orifice
LP Orifice Marking

Color

BTU Rating / LP Gas

_*Note: For operation
_shall be reduced
level.
For all burner

5,000

9,500

12,000

14,000

16,000

1.01

1.54

1.75

1.93

1.99

.68

.89

.95

1.01

1.15

Blue

None

Green

Red

Black

4,500

8,000

10,000

11,000

14,000

above 2000 ft., appliance

at elevations

at the rate of 4 percent

Do Not _
R.....

rating

for each 1000 ft. above sea

7 Electrode

Fig. 11

Fig. 10

locations:

a. Remove the top grates and burner
b. Lift off the burner heads.

caps (See

Fig. 10).

c. Remove the factory installed natural gas orifices one at a time from the center of the orifice holder using a 7 mm nutdriver (See Fig. 11).
Remember to keep the original Natural Gas Orifices for later conversion to Natural Gas.
d. Replace the orifice with the correct LP/Propane gas orifice (See the Surface Burner Orifice Data Chart ; also refer to Fig 9 for the
correct LP orifice installation at each of the surface burner locations). Tighten each orifice until snug. Use caution not to overtighten.
Repeat for each surface burner.
e. Replace the burner heads. Match letter located under center of Burner Caps with letter located inside Burner Heads. Match the letter
stamped on Burner Skirt with Burner Head and Burner Cap. (Refer to Fig. 9). Be sure burner heads mate correctly with each surface
igniter, then replace the burner caps and burner grates.

BURNER
Use caution

when

STYLE

replacing

#2 CONVERSION

each burner

cap so the electrode

INSTRUCTIONS
is not damaged.

7ram Nut Driver

Mounting screws

Ignitor Alignment

Unlike the standard
gas range,
THIS COOKTOP IS
NOT REMOVABLE.
Do not attempt
to remove this
cooktop.
For all burner

Fig. 14

oril
Fig. 13

Fig. 12

locations:

a. Remove Burner Grates & Burner Caps.
b. If the opening in the burner is too small to allow removal of the orifice, remove the burner as follows: Remove 2 screws using #1 square tip driver and
remove Burner Heads (Figs 12 ). NOTE - Some models may have 3/16" hex head screws instead of square drive screws.
c. Remove the factory installed natural gas orifices from the center of the orifice holders using a 7 mm nutdriver (See Fig. 13). Save the natural gas
orifices removed from the appliance for possible future conversion
back to natural gas.
d. Following the chart below select the appropriate LP/Propane gas orifice from the envelope labeled SCREW MOUNTED
BURNER
LP KIT.
EXAMPLE:
Natural Gas orifcie marked 1.07 is replaced by LP orfice marked .66. Tighten all orifices until snug. Use CAUTION not to overtighten.
e. Replace burner heads at all locations and tighten each position with original screws using #1 square tip driver. Make sure that the center of the ignitor
aligns with the center nib in the burner head (Figs. 14). Heads MUST have a Burner Cap installed to insure proper ignition and gas flame size.
GAS SURFACE

BURNER ORIFICE DATA CHART (Burner

BTU Rating / Natural Gas

5,000

Style #2)

9,500/10,000

12,000

14,000

15,000

16,000

17,000

18,000

Natural Gas Orifice

1.07

1.46

1.67

1.87

1.95

1.98

2.1

2.2

L P Gas Orifice

0.66

0.93

1.02

1.09

1.18

LP Orifice Marking Color

Pink

White

Yellow

Brown

Silver

BTU Rating / LP Gas

5,000

9,500

12,000

14,000

16,000

*Note: For operation at elevations
above 2000 ft., appliance rating
shall be reduced at the rate of 4
percent

for each 1000 ft. above
sea level.

BURNER

STYLE #3 (TWIN

BURNER)

CONVERSION

INSTRUCTIONS
Fig. 17
!

Simmer

_win

Two Piece Burner Cap

Remove Burner Mounting Screws

Unlike the standard gas range, THIS COOKTOP
Do not attempt to remove this cooktop.
For all burner locations:
a. Remove burner grates & lift off the two piece burner cap. (Fig. 15)

_Orifice

Orifice

Orifices

Openings

IS NOT REMOVABLE.

b. Remove the two burner mounting screws using the appropriate screwdriver or nutdriver and remove burner head (Figs 16). NOTE - Burners may be
secured with 3/16" hex head screws or square drive screws,
c. Remove the factory installed natural gas orifices from the orifice holders using a 7 mm nutdriver (See Fig 17). Save the natural gas orifices
removed from the appliance for possible future conversion
back to natural gas.
d. Replace the orifice in each of the orifice holders with the appropriate LP/Propane gas orifice from the envelope labeled SCREW MOUNTED
BURNER
LP KIT. Note that there are two identical orifices for the main portion of the burner and a separate smaller orifice for the center/simmer
portion of the burner. Tighten all orifices until snug. Use CAUTION not to overtighten.
e. Replace burners at all locations and tighten each position with original screws. Burners MUST have a Burner Cap installed to insure proper ignition
and gas flame size.
GAS SURFACE

BURNER ORIFICE DATA CHART (Burner
SIMMER

TWIN (Main)

BTU Rating / Natural Gas

750

17,000

Natural Gas Orifice

0.43

1.46

L P Gas Orifice
LP Orifice Marking Color
BTU Rating / LP Gas

BURNER

(Qty 2)

0.22

0.84 (Qty 2)

Orange

Purple

750

15,000

STYLE

*Note: For operation at elevations
above 2000 ft., appliance rating shall
be reduced at the rate of 4 percent for
each 1000 ft. above sea level.

Style #3)

#3 (TWIN BURNER)

CONTROL

Adjust the "LOW" Setting of the Twin Burner Surface Valve
(Figure 18) (some models):
Note: On the Twin burner surface valve the low setting of each portion
(inner portion and outer portion of the twin burner) should be adjusted
individually.
a. Push in and turn control to ignite the burner
b. Quickly turn knob to LOWEST POSITION.
c. If burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. The inner portion of the twin burner flame size can be increased or
decreased with the turn of the screwA. Use screw B to adjust the
flame size of the outer portion of the twin burner. Turn
counterclockwise the screw to increase flame size. Turn clockwise the
screw to decrease flame size. Adjust flame until you can quickly turn
knob from LITE to LOWEST POSITION without extinguishing the
flame. Flame should be as small as possible without going out.
Note: Air mixture adjustment is not required on surface burners.

VALVE ADJUSTMENT
Fig.

_'_
,_

]

Convert

Oven

for LP/Propane
a.
b.

Burner

Orifice

Gas (16,000

Fig. t9

BTU*)

Locate the oven burner spud (See Fig. 18).
Using a 1/2" wrench, turn down the adjustable spud, which injects gas
into the oven burner, until snug against the LP/Propane metering pin
(approximately 2-1/2 turns). Do not over tighten.

4. Convert Waist=High
Broiler Burner
Flame for LP/Propane Gas (13,500

Orifice
BTU*)

( Some Models )
a.
b.

Open the oven door.
Locate the broiler burner spud and turn down until snug against the LP/
Propane metering pin (approximately 1 to 1-1/2 turns). Do not over tighten
(See Fig. 18).
Oven Burner
Orifice

I *Note:
be reduced
For operation
at the rateatofelevations
4 percent above
for each
2000
1000
ft,, ft.
appliance
above sea
rating
level,shall

5. Reconnect

Gas and Electrical

Leak testing of the appliance

Supply

to Range.

shall be conducted according to the Installation

Instructions

provided with the Range.

Do not use a flame to check for gas leaks.
Checking Manifold Gas Pressure
If it should be necessary to check the manifold gas pressure, remove the burner cap and connect a manometer (water gauge) or other pressure device
to the top right front burner orifice. Using a rubber hose with inside diameter of approximately 1/4/' hold tubing down tight over orifice. Turn burner valve
on. For an accurate pressure check, have at least two (2) other surface burners burning. Be sure the gas supply (inlet) pressure is at least one inch above
specified range manifold pressure. The gas supply pressure should never be over 14" water column. When properly adjusted the manifold water column
pressure is 10" for LP/Propane gas or 4" for Natural gas.
Pressure Testing Gas Supply Piping System
a.
Disconnect the range and its individual shut-off valve from the gas supply piping system during any pressure testing of that system at test pressures
greater than 14" of water column pressure (approximately 1/2" psig).
b.
Isolate the range from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping
system at test pressures equal to or less than 14" of water column pressure (approximately 1/2" psig).

6. Test surface burners
should be adjusted"

to verify

if "LOW"

setting

a.
b.
c.
d.

Push in and turn control to LITE until burner ignites.
Push in and quickly turn knob to LOWEST POSITION.
if burner goes out, reset control to OFR
Remove the surface burner control knob.

insert a thin-bladed screwdriver into the hollow valve stem and engage the slotted
screw inside. Flame size can be increased or decreased with the turn of the screw.
Turn counterclockwise to increase flame size. Turn clockwise to decrease flame size.

%
To
Surface
Burner

NOTE:

For Twin Burner Valve Adjustments

Fig: 20

(See Figs. 19 & 20).
Adjust flame until you can quickly turn knob from LITE to LOWEST POSITION without
extinguishing the flame. Flame should be as small as possible without going out.

Burner Flame Size

follow the instructions on page 5.

Main
Top
Fig: 21

7. Air Shutter=Oven

Burner

1" Flame

The air shutter for the oven burner may need adjustment, especially if the unit has been
converted for use with LP/Propane gas. The approximate flame length of the oven burner
is 1 inch (distinct inner, blue flame) (See Fig. 21).
To determine if the oven burner flame is proper:
a.
To access the air shutter you must remove the storage drawer or warmer drawer
(see removal instructions on page 2).
b.
Remove the oven bottom by removing the screws at rear of oven bottom. Lift up
the rear of oven bottom and slide toward back of range to disengage from front of
oven front frame.
c.
d.

Remove burner baffle by removing nut located on top of baffle and two screws from
front edge of oven front frame. Lift baffle straight up and out of the oven.
Set the oven to bake at 350°F and observe the flame. If the flame is yellow in color,
increase air shutter opening size. if the flame is a distinct blue color, but lifting away
from the burner; reduce the air shutter opening size.

Fig. 22

( Continued

on following

page )

Burner

Oven

Tube
Z

Burner

Waist-High

"'J

Locking

iLower

Screw

Ov_enBaffle

BUI

Lock

(Self Clean ;Mo(
_;4_mAir

Air Shutter

Shutter

Screw

Air Shutter

Orifice

Hood

--:::-"
Fig. 25

Orifice Hood
(Spud)

Fig. 23

ii
_ _

-Lower Oven Bottom
Air Shutter (Removable)

Fig. 24
e.

Turn off oven and allow to cool before adjusting air shutter. To adjust, loosen lock-screw (3), reposition air shutter (2), and tighten lock-screw (3)
(See Fig. 22). Retest the burner by repeating step "d" above. When the burner flame is a distinct blue color burning steady, the air shutter is
adjusted correctly.
Replace burner baffle and oven bottom.

8. Air Shutter=Broil
a.
b.

Burner

Observe the flame to determine if the broiler burner flame is properly adjusted, it should be steady with approximately 1" blue cones and no yellow or
orange flame tips (See Fig. 23).
if adjustment to the air shutter is necessary, locate the broiler burner air shutter (See Fig. 24), loosen shutter lock screw, and adjust to obtain optimum
flame. This will normally be completely open for LP/Propane gas. if the flame is yellow in color, increase the air shutter opening size. if the flame is a
distinct blue, but lifting away from the burner, reduce the air shutter opening size. Tighten the shutter set screw.

9. Replace Storage Drawer or Warmer Drawer
(instructions
for warmer drawer if equipped):

I Fig.26

a.
b.

Pull the bearing glides to the front of the chassis glide (See Fig. 25).
Align the glide on each side of the drawer with the glide slots on the range.

Push
the drawer
intointo
the position.
range until
levers
(approximately
drawer
openglides
again do
to
seat bearing
glides
If you
do "click"
not hear
the levers 2").
"click"Pull orthethe
bearing

_._
I

_,,,,,_-,--,_

"_\-_

oo,,o.,.oa,o0.o ovo,,o0
a
a o ao0
damage to the bearing glides.

10. installation
and Conversion
a.

of New LP/Propane
Label

Using the list on page 8, determine the Surface Burner Combination
to the range after it has been converted

c.
e.

Rating/Serial

and select the corresponding

Plate

that applies

Remove Storage Drawer

(somemodels),

Panel or Warmer Drawer (if equipped)
for access to Regulator

Rating Plate

part number in the approprate language (English/French).
Use a pen or permanent marker to fill out the LP/Propane Rating/Serial plate.
include the date that the LP conversion was performed and the service company
or individual performing the conversion. See the sample label below
Place new plate as close as possible to the existing Rating/Serial plate on range
(See the recommended locations shown in Fig. 26).

Serial
Plate

Remove the lower storage or warmer drawer and install the Regulator L.P.
Conversion

Label in the location shown in figure 26.

Fig. 27

Pressure Regulator
location at rear of ranc

THIS CONTROL
HAS BEEN CONVERTED
FOR USE WITH

p/n 316241200

Sample

CONVERSION

- L.P, Rating/Serial

TO NATURAL

E:_E
::,T::L CE.ROOR,_.TEUR.
_eT_ CONVERT!

_
_U
HU
HA S|DO CONVERTIDO
PARA USARSE

POUR ETRE UT L S_
. ........

(0811)

Sample - Regulator L.P. Conversion Label

Plate

GAS

if it becomes necessary to convert the range back to natural gas:
a.
Disconnect gas and electrical supply from range.
b.
Convert pressure regulator (See step 1), turn cap over so the solid end of cap faces outward. Place the hollow end of the cap into the loop end of the
dust protector.
c.
Remove the LP orifices using 7ram nutdriver and replace with the original factory installed natural gas orifices at their original locations (See figure 9
for locations).
d.
Convert Oven Burner Orifice for Natural Gas by loosening spud counter-clockwise (approximately 2-1/2 turns; See step 3).
e.
Convert Waist-High Broiler Burner Orifice (Self-Cleaning Models Only) for Natural Gas by loosening spud counter-clockwise (approximately 1 to 1-1/2
turns; See step 4.)
f.
Readjust "LOW" Setting for Surface Burner Valves following instructions. (See step 6.)
g.
Readjust Oven & Broil Burner Air Shutters. (See steps 7 & 8.)

GRLP3
:)TY
1
1
1
1
1
1
5
1
1
1
1
1
4
1
2
1

CONVERSION

KIT - CONTENTS

Pa_ Number
316037528
316417518
316241200
316237910
316237904
316237905
316237906
316237907

Item Description
LP Conversion Kit Label
Instructions, Kit, GRLP3
LP Conversion Label - Regulator
Orifice 14,000 Btu/h size 1.15
Orifice 11,000 Btu/h size 1.01
Orifice 10,000 Btu/h size .95
Orifice 8,000 Btu/h
size .89
Orifice 4,500 Btu/h
size .68

For
For
For
For
For

Non
Non
Non
Non
Non

316255600
316527507
316527512
316527503
316527501
316527505
316527515
316527516

Label,
Orifice
Orifice
Orifice
Orifice
Orifice
Orifice
Orifice

For
For
For
For
For
For
For

Screw
Screw
Screw
Screw
Screw
Screw
Screw

Qty

Pa_
Number

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

316005215
316005216
316005217
316005218
316005219
316005220
316005221
316005222
316005223
316005224
316005225
316005226
316005227
316005228
316005229
316005230
316005233
316005234
316005235
316005236
316005237
316005238
316005239
316005240
316005241
316005242
316005243
316005244

Insert Kit Screw Down Burner
16,000 Btu/h size 1.18
14,000 Btu/h size 1.09
12,000 Btu/h size 1.02
9,500 Btu/h
size .93
5,000 Btu/h
size .66
15,000 Btu/h size .84
750 Btu/h
size .22

Description
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating
Rating

Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate

Notes

English
English
English
English
French
French
French
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French

Surface Burner Combination
4-8k
3-8k, 1-10k
2-8k, 1-10k,
1-8k, 1-10k,
4-8k
3-8k, 1-10k
2-8k, 1-10k,
1-8k, 1-10k,
2-8k, 1-11k,
2-8k, 1-11k,
3-8k, 1-11k
3-8k, 1-11k
1-8k, 1-10k,
1-8k, 1-10k,
2-8k, 1-10k,
2-8k, 1-10k,
4-9.5k
4-9.5k

1-4.5k
1-4.5k, 1-11k

1-4.5k
1-4.5k, 1-11k
1-4.5k
1-4.5k

1-4.5k,
1-4.5k,
1-4.5k,
1-4.5k,

1-14k
1-14k
1-14k
1-14k

4-8k,
4-8k,
3-8k,
3-8k,
5-8k
5-8k

1-4.5k
1-4.5k
1-4.5k, 1-11k
1-4.5k, 1-11k

4-8k,
4-8k,
2-8k,
2-8k,

1-10k
1-10k
1-10k, 1-4.5k, 1-11k
1-10k, 1-4.5k, 1-11k

Mounted
Mounted
Mounted
Mounted
Mounted

Qty

Pa_
Number

1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

316005245
316005246
316005247
316005248
316005249
316005250
316005251
316005252
316005253
316005254
316005255
316005256
316005257
316005258
316005259
316005260
316005261
316005262
316005263
316005264
316005265
316005266
316005267
316005268
316005269
316005270
316005271
316005272
316005277
316005278
316005279
316005280
316005281
316005282
316005283
316005284
316005285
316005286
316005287
316005288

Burner
Burner
Burner
Burner
Burner

Mounted
Mounted
Mounted
Mounted
Mounted
Mounted
Mounted

(Style
(Style
(Style
(Style
(Style

Burner
Burner
Burner
Burner
Burner
Burner
Burner

(Style
(Style
(Style
(Style
(Style
(Style
(Style

Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate
Plate

1)
1)
1)
1)or Oval BumerA
1)

English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
English
French
French
English
English
French
English
French
English
French
English
French
English
French
French
English

2)
2)
2)
2) or Oval Burner B
2)
3)
3)

Surface Burner Combination

3-9.5k, 1-12k
3-9.5k, 1-12k
3-9.5k, 1-14k
3-9.5k, 1-14k
2-9.5k, 1-12k, 1-5k
2-9.5k, 1-12k, 1-5k
2-9.5k, 1-5k, 1-14k
2-9.5k, 1-5k, 1-14k
1-9.5k, 1-12k, 1-5k, 1-16k
1-9.5k, 1-12k, 1-5k, 1-16k
2-9.5k, 1-12k, 1-5k, 1-16k
2-9.5k, 1-12k, 1-5k, 1-16k
4-9.5k, 1-5k
4-9.5k, 1-5k
1-9.5k, 1-8k, 1-12k, 1-5k, 1-16k
1-9.5k, 1-8k, 1-12k, 1-5k, 1-16k
4-9.5k, 1-8k
4-9.5k, 1-8k
3-9.5k, 1-8k, 1-12k
3-9.5k, 1-8k, 1-12k
1-9.5k, 1-12k, 1-5k, 1-14k
1-9.5k, 1-12k, 1-5k, 1-14k
2-9.5k, 1-14k, 1-5k, 1-8k
2-9.5k, 1-14k, 1-5k, 1-8k
1-9.5k, 1-14k, 1-12k, 1-5k
1-9.5k, 1-14k, 1-12k, 1-5k
1-15k, 1-14k, 1-8k, 1-9.5k, 1-5k
1-15k, 1-14k, 1-8k, 1-9.5k, 1-5k
1-16k, 1-14k, 2-9.5k. 1-5k
1-16k, 1-14k, 2-9.5k. 1-5k
1-16k, 1-14k, 2-9.5k. 1-5k
1-16k, 1-14k, 2-9.5k. 1-5k
1-16k, 1-14k, 2-9.5k. 1-5k
1-16k, 1-14k, 2-9.5k. 1-5k
5-9.5k
5-9.5k
3-9k, 1-5k, 1-12k
3-9k, 1-5k, 1-12k
1-14k, 2-9k, 1-5k, 1-15k
1-14k, 2-9k, 1-5k, 1-15k

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 8
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Sun Sep 28 20:46:28 2014
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Frigidaire BGGF3031KBC User Manual GAS RANGE Manuals And Guides 1408061L

Navigation menu

Versions of this User Manual:

Views

Navigation