Frigidaire FFTW4120SW WASHER INST A07504201 User Manual Manuals And Guides 1705316L

User Manual: Frigidaire FFTW4120SW FFTW4120SW FRIGIDAIRE WASHER - Manuals and Guides View the owners manual for your FRIGIDAIRE WASHER #FFTW4120SW. Home:Laundry & Garment Care Parts:Frigidaire Parts:Frigidaire WASHER Manual

Open the PDF directly: View PDF .
Page Count: 10

Download
Open PDF In Browser	View PDF

All about the

Installation
of your Washer

TA B L E O F C O N T E N T S
Important Safety Instructions ........................... 2-3

Accessories ...................................................... 10

Installation Requirements ................................ 4-6

Français........................................................... 11

Installation Instructions ................................... 7-9

Español ........................................................... 21

A07504201A (1610)

IMPORTANT SAFETY INSTRUCTIONS
WARNING
Please read all instructions before using this washer.

Installation Checklist
Leveling
 Washer is level, side-to-side and front-to-back
 Cabinet is setting solid on all corners

Recognize safety symbols, words and
labels
Safety items throughout this manual are labeled with a
WARNING or CAUTION based on the risk type as described
below:

Water Supply
 Use only new hoses and verify rubber sealing
washers are installed
 HOT supply is connected to HOT inlet and COLD
supply is connected to COLD inlet
 HOT and COLD water supply turned on

Definitions
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.

 No leaks present at water supply connections or
appliance inlet connections recheck in 24 hours

Drain
 Drain hose mounted securely to pump outlet with
supplied clamp (check for leaks)

DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.

WARNING
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.

CAUTION
CAUTION indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.

 Drain hose snapped in “U” channel (shipped in
drum)
 Stand pipe or wall drain height minimum 39”
 Drain hose secured in place with cable tie (shipped
in tub)

Electrical Power
House power turned on
 Washer plugged in

Final Checks
 Installation Instructions and Use and Care Guide
read thoroughly
 Water enters tub when cycle starts with lid lowered.

IMPORTANT
IMPORTANT indicates installation, operation or maintenance
information which is important but not hazard-related.

2

 Registration card sent in

IMPORTANT SAFETY INSTRUCTIONS
WARNING

NOTE
The electrical service to the washer must conform with
local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70, or in Canada, the
Canadian Electrical Code C22.1 part 1.

WARNING
SUFFOCATION HAZARD
Destroy the carton and plastic bags after the washer is
unpacked. Children might use them for play. Cartons covered
with rugs, bedspreads, or plastic sheets can become airtight
chambers causing suffocation. Place all materials in a garbage
container or make materials inaccessible to children.

CAUTION
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than one person
move or lift the washer.

FIRE HAZARD
For your safety the information in this manual must be
followed to minimize the risk of fire or explosion or to
prevent property damage, personal injury or loss of life. Do
not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.

IMPORTANT
The instructions in this manual and all other literature
included with this washer are not meant to cover every
possible condition and situation that may occur. Good safe
practice and caution MUST be applied when installing,
operating and maintaining any appliance.
Maximum benefits and enjoyment are achieved when all
the Safety and Operating Instructions are understood and
practiced as a routine with your laundering tasks.

Save these instructions for future reference.

Tools and materials needed for installation:

AND

Adjustable
pliers

Carpenter’s level

Inlet hose (x2)

NOTE
Hoses are not included with washer purchase. See
“Accessories” section for various inlet hose kits to fit your
specific installation.

3

INSTALLATION REQUIREMENTS
Electrical system requirements
CIRCUIT - Individual, properly polarized and grounded 15
amp. branch circuit fused with 15 amp. time delay fuse
or circuit breaker.
POWER SUPPLY - 2 wire, with ground, 120 volt single phase,
60 Hz, Alternating Current.

NOTE
Because of potentially inconsistent voltage capabilities,
the use of this washer with power created by gas powered
generators, solar powered generators, wind powered
generators or any other generator other than the local
utility company is not recommended.
OUTLET RECEPTACLE - Properly grounded 3-prong receptacle
to be located so the power supply cord is accessible
when the washer is in an installed position.

Grounding type
wallll receptacle
wa
receptacl

Do not, under
anyy circumstances,
an
circumstances,
cut, remo
remove
ve,
or bypass
bypass th
the
grounding
gr
ounding pr
prong.
ong.

Power cord with
Power
3-prong gr
grounded
ounded plug

NOTE
GFI (Ground Fault Interrupter) receptacle is not required.

4

Ground requirements
WARNING
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment grounding conductor
can result in a risk of electrical shock. Check with a licensed
electrician if you are in doubt as to whether the appliance is
properly grounded.

1 The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electrical shock by a path of least resistance for
electrical current.
2 Since your washer is equipped with a power supply
cord having an equipment-grounding conductor and
a grounding plug, the plug MUST be plugged into an
appropriate, copper wired receptacle that is properly
installed and grounded in accordance with all local codes
and ordinances or in the absence of local codes, with the
National Electrical Codes, ANSI/NFPA 70 (latest edition).
If in doubt, call a licensed electrician. DO NOT cut off
or alter the grounding prong on the power supply cord.
In situations where a two-slot receptacle is present, it is
the owner’s responsibility to have a licensed electrician
replace it with a properly grounded three prong
grounding type receptacle.

Water supply requirements
Hot and cold water faucets MUST be 3/4 inch with threading
for laundry hose connection. Water pressure MUST be
between 30 and 120 psi. Pressure difference between hot and
cold cannot be more than 10 psi. Your water department can
advise you of your water pressure.

INSTALLATION REQUIREMENTS
Drain system requirements
1 Drain capable of eliminating 17 gals (64.3 L) per minute.
2 A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.
3 The standpipe height above the floor should be:
Minimum height: 39 in. (99 cm)
Maximum height: 96 in. (244 cm)

Installation in a Recess or Closet
If washer and dryer are installed in the same closet, door
ventilation is required: A minimum of 120 square inches
(774.2 cm²) of opening, equally divided at the top and
bottom of the door, is required. Louvered openings should
be located 3 inches (7.6 cm) from bottom and top of door.
Air openings are required to be unobstructed when a door is
installed. A louvered door with equivalent air openings for the
full length of the door is acceptable.

3”
(7.6cm)

60 sq. in.
(387.1cm²)

96”
(244 cm)
max.
39”
(99 cm)
min.

NOTE
For installations requiring a longer drain hose, have a
qualified technician install a longer drain hose (according
to your model number) available from an authorized parts
distributor. For drain systems in the floor, install a syphon
break kit available from your local hardware store.

60 sq. in.
(387.1cm²)

3”
(7.6cm)

closet door

5

INSTALLATION REQUIREMENTS
Clearance requirements

MINIMUM INSTALLATION CLEARANCES - Inches (cm)
SIDES

REAR

TOP

FRONT

Alcove

1”
(2.5 cm)

6”
(15.2 cm)

24”
(61 cm)

n/a

Closet

1”
(2.5 cm)

6”
(15.2 cm)

24”
(61 cm)

2”
(5.1 cm)

IMPORTANT
DO NOT INSTALL YOUR WASHER:
1 In an area exposed to dripping water or outside
weather conditions. The ambient temperature should
never be below 60° F (15.6° C) to maximize detergent
effectiveness.
2 In an area (garage or garage-type building) where
gasoline or other flammables (including automobiles)
are kept or stored.

1”
(2.5 cm)

1”
(2.5 cm)

2”
(5.1 cm)

6”
(15.2 cm)

3 On carpet. Floor MUST be solid with a maximum
slope of 1 inch (2.5 cm). To minimize vibration
or movement, reinforcement of the floor may be
necessary.
24”
(61 cm)

Washer Dimensions
water supply
connection on
rear of washer
59” (150 cm)
to clear open lid

38.5”
(97.5 cm)
tuyau de vidange
à l’arrière de la
laveuse1

power cord
attachment location
on rear of unit2

27.0” (68.5 cm)
Drain hose length on washer approximately 59 inches (150 cm).
Power supply cord length approximately 70.5 inches (180 cm).

1
2

6

44.2”
(112 cm)

29.0” (73.6 cm)

INSTALLATION INSTRUCTIONS
Leveling your washer
Excessive noise and vibration can be prevented by properly
leveling the washer.
1 With the washer within 4 feet (1 m) of its final location,
use a carpenter’s level to level your washer front-toback and side-to-side. For front-to-back leveling, place
edge of the level flush to the front panel. For side-toside leveling place the edge of the level flush to the
side panel.
2 Use adjustable pliers to adjust the front leveling legs so
the washer is level front-to-rear and side-to-side, and
stable corner-to-corner.
3 Press down on alternate corners and sides and feel for
the slightest movement. Adjust the appropriate front
leg(s) so the washer sits solidly on the floor on ALL four
legs. Keep the leveling leg extension at a minimum for
best performance of the washer.

b

a

raise

c

lower

d

Connecting inlet water
1 Run some water from the hot and cold faucets to flush
the water lines and remove particles that might clog
the water valve screens and to determine which faucet
is hot and which is cold supply.

RUBBER WASHERS
MUST BE PRESENT

a
b

USE ONLY
NEW HOSES

d

c

NOTE
Hoses are not included with washer purchase. See
“Accessories” section for various inlet hose kits to fit your
specific installation.
2 Connect the HOT inlet hose to the HOT inlet connection
on the washer and the COLD inlet hose to the COLD
inlet connection on the washer. Tighten by hand until
snug. Then tighten each supply connection another
2/3 turn with pliers. Do not cross thread or overtighten these connections.
3 Connect the HOT inlet hose to the HOT water supply
and the COLD inlet hose to the COLD water supply.
Tighten by hand until snug. Then tighten each supply
connection another 2/3 turn with pliers. Do not bend,
kink or pinch water inlet hoses.
4 Turn on the water and check for leaks.

f
e

BLUE
(COLD)

RED
(HOT)

g

7

INSTALLATION INSTRUCTIONS
Connecting drain hose to washer
IMPORTANT
Inspect rubber flap on pump outlet. Ensure it is in place
and not folded under or torn.
1 With the spring clamp already installed, place the drain
hose elbow over the pump outlet at the lower rear of
the washer. Ensure the hose elbow is completely and
squarely seated to the pump outlet before using pliers
to move the spring clamp into place.

DRAIN PUMP
OUTLET

SLIDE CLAMP
TO HERE

SPRING CLAMP

8

INSTALLATION INSTRUCTIONS
Connecting drain and electrical
1 Snap one end of the drain hose hanger (shipped in
washer drum) onto the drain hose. Continue wrapping
it around the hanger and snap it in place.
2 Place the hook end of the drain hose in the drain
opening. Secure the drain hose with the cable tie
(provided in the enclosure package) to the standpipe,
inlet hose, laundry tub, etc. so the hose does not pull
out from the force of the water.

NOTE
The standpipe inside diameter must be 1-1/4” (3.2 cm)
minimum. There must be an air gap around the drain hose
in the standpipe. A snug hose fit can cause a siphoning
action.

IMPORTANT
Check to ensure the power is off at a circuit breaker/fuse
box before plugging the power cord into an outlet.
3 Plug the power cord into a grounded outlet.
CABLE TIE

Grounding type
wallll receptacle
wa
receptacl

Do not, under
anyy circumstances,
an
circumstances,
cut, remo
remove
ve,
or bypass
bypass th
the
grounding
gr
ounding pr
prong.
ong.

Power cord with
Power
3-prong gr
grounded
ounded plug
4 Turn on the power at the circuit breaker/fuse box.
5 Carefully slide the washer to its final position. Recheck
for level and rock corners for stability.
6 Read the Use & Care Guide provided with the washer. It
contains valuable and helpful information that will save
you time and money.
7 Run the washer through a complete cycle, checking for
water leaks and proper operation.
8 If you have any questions during initial operation,
please review the “Avoid Service Checklist” in your Use
& Care Guide before calling for service.
9 Place these instructions in a location near the appliance
for future reference.

9

ACCESSORIES
INLET HOSE KITS
Please call 866-233-8353 (in Canada, 800-265-8352) to
explore hose kit options that will meet your specific installation
needs.
UNIVERSAL APPLIANCE WRENCH
P/N 137019200
A UNIVERSAL APPLIANCE WRENCH is available to aid in
dryer/washer feet adjustment.

CAUTION
Failure to use accessories manufactured by (or approved by)
the manufacturer could result in personal injury, property
damage or damage to the washer.

TOUCH UP PAINT PENS*
Classic White Touch Up Pen - P/N 5304468812

*Other colors may be available. Contact the source where you
purchased your washer.

Replacement parts:
If replacements parts are needed for your washer, contact the
source where you purchased your washer or refer to your Use
and Care Guide for more information.

10

WARNING
ELECTRICAL SHOCK HAZARD
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : LeeMar01
Create Date                     : 2016:11:10 11:46:10-06:00
Modify Date                     : 2017:05:17 09:23:55-05:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : WASHER INST-A07504201.indd
Creator                         : LeeMar01
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:05:17 09:23:55-05:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:c9916b4c-cfdc-4375-b45d-529c2037e035
Instance ID                     : uuid:33a92fbc-81c8-4df4-b3b7-eb1f372b94da
Page Count                      : 10

EXIF Metadata provided by EXIF.tools