Frigidaire FGID2474QB4B User Manual DISHWASHER Manuals And Guides 1502103L
User Manual: Frigidaire FGID2474QB4B FGID2474QB4B FRIGIDAIRE DISHWASHER - Manuals and Guides View the owners manual for your FRIGIDAIRE DISHWASHER #FGID2474QB4B. Home:Kitchen Appliance Parts:Frigidaire Parts:Frigidaire DISHWASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dishwasher Figure 3 CD.808 936 635 Installation Instructions Front Closed _23¾"(60,3 cm)-_ _24¼"(61,5 cm)_ NOTE: Put unit on its back being careful not to pinch the Water Drain Hose. 1. 2. Tilt and pull forward the kickplate to remove it. - see Figure 1. NOTE:It is not necessary to remove the outer door for installation• e cm) e ® Opendoor to900 90,8jm)** Height 0nly adjustableto 35 ¾" (90,8cm) max when *DIMENSIONS DONOTINCLUDE INSULATION- Power supply/water dishwasher. For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher• The dishwasher is provided with water heating feature. The dishwasher is intended for connection Tip Over Hazard Do not use dishwasher until completely / / 35¾" I to hot water supply. ® installedin35 ¾" (90,8cm)maxstandardcabinetrycutout. INSULATION BLACKET MAYBECOMPRESSED inlet location to 353A'' UPONINSTALLATION. IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance between the wall and the open door. 2. Floor shouldbe flat and freeof any obstruction. IMPORTANT: Drain, water, and electrical roughed-in before going any further. ® installed. lines should be Electric Shock Hazard Electrical, water, and drain lines must be confined to shaded areas in Figure 2. Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock. Do not push down on open door. Failure to follow this warning can result in serious injury. Cut Hazard Figure Locate water inlet valve behind kickplate on bottom left underside of unit. See Figure 4 The valve has a 3/8" ( 1 cm ) NPT male fitting• 4. Connect the 90 ° elbow (not included) to water inlet valve. When tightened, point elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4. Cabinet Preparation: As a precaution, it is recommended, but not required that the cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/moisture damage. Tools and Materials Needed for Installation • • • • • Flaring Tool / Tube Cutter (for copper tubing) Flashlight Level • Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) Pliers • • • • • • • • • • 1. Brass Elbow (Not Included) Electric Shock Hazard all local codes and ordinances Observe for 1. qualified persons. Failure to follow this warning could result in death or serious injury. 2. • Drain HoseClamp, 11/4" (3,1 cm)Diameter • Brass Elbow, 90 ° with a 3/4" ( Q 2 cm )-11.5 NH to 3/8" ( Q 2 cm ) NPT Compression fitting • Conduit Connector (UL Listed) • Wire Nuts, three (3) for 12-14 gauge wire (UL Listed) range, Damage to tub or other components 34"(86,36cm) min.to35¾" (90,8cm) max.** 90° -_" I Electrical, water, and drain lines must be confined to shaded area. Preferred Drain Areas 3" "(45,7 cm) and 3" (7,6cm) cm) max. height Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. Review dimensions in Figure 2 to locate dishwasher's drain, water, and electrical connections• All utilities must be routed in shaded area in the Figure 2 3½" (8,89 cm) min.to _/' 4½"(11,430m) m_x. _/// / / _4_ /.,,_/ standardcabinetrycutout. (5/16"[0,8cm]mfn. ¼" (3,1 cm) clearance required from unit to _J(5,7 2¼" cm) \.,_4_\ Ix 1", \ will Note: Locate the electrical supply and dishwasher's electrical junction box on right underside of unit behind kickplate assembly• See Figure 4. Determine where you will connect to hot water supply• Review Figure 4 and note the location of water inlet valve. Determine where you will connect the drain hose. 3. Cut access holes for the Electrical, Water and Drain hoses in the cabinet within the shaded areas as shown in Figure 2. 4. The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. 5. Pull electrical cable through hole into installation area. 6. Be sure water inlet valve is protected from freezing. If valve freezes and ruptures, flooding may occur• 7. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve• Extra hose length is necessary High-pressure and high-temperature Stainless Flexible hose with a minimum inner diameter of 1/4" may be used. A shut-off valve installed outside dishwasher cabinet is best. 8. Route water supply line into installation area. 9. Stand dishwasher back upright for further installation. .X IMPORTANT: Incoming hot water temperature should be at 24" (61 cm) .................................................................................................................................................................................................................... least 120°F (49°0). Water pressure should be between 20-90 psi. underside ofcountertop.) of countertop area. Anchoring ® To install the Side Mounting Clips• Note: Install Side Mount Brackets before unit is installed into the cabinet. Insert screws into the front holes of the clips only. Use extreme caution when fixing the screws, not to cratch dishwashers or kitchen cabinet. Make sure your location has the correct drain, water, and electrical outlets to make the connections• Do not install unit under a cooktop occur. from underside Choose one of the methods of attachment below to secure unit, holes need to be pre-drilled using a Q5 drill bit regardless of the option chosen: a. Side Mount Cabinet Clips (Preferred Method of attachment) b. Top Mount Cabinet Clips (to be used when Side Mount is not an available option) CAUTION: Use extreme care .n mounting the dishwasher as to not scratch, bump or otherwise damage the console or tub. Figure 2 1• height of cabinet opening Dishwasher Electrical Line Locating the Connections electrical and plumbing connections. All electrical and plumbing work should be performed by Measure to floor. .• Move front of installation Adjust dishwasher the levelling to legs. 4. Parts You Will Need*(Not Included) "klf required: • "Y" Branch Tailpiece and Connector Kit (See Step 8 ) • Air Gap Kit (See Step 8 ) All the parts can be found at local hardware, electrical plumbing supply stores• 333A,, Adjustabl, to 353A'' Water line (Not Included) Safety Glasses Saw, Keyhole or 1/2", 11/2" to 2" Hole Cutters Screw Drivers, Slotted and Q2 Phillips (magnetic tip preferred) Work gloves Tape, Electrical or Duct Measuring Tape Wire Stripper or Utility Knife Wrench, Hex-end Wrenches, 2 Adjustable (for copper tubing) or 2 Pipe wrenches (for iron pipe plumbing) 6 4 3. Parts Included: Figure NOTE: If dishwasher is installed at end of a cabinet, sides and back must be fully enclosed. To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit. (Not Included) Drill, Electric Driver, Socket 5/32% 1/4", 5/16" 5 NOTE: Install cabinet seal to dishwasher before placing it into the cabinet 33¾" (86cm), Adjustable to Remove two (2) screws at the top the kickplate assembly Figure before installing Figure _- 22½"(57,1 INSTALLER: Leave Installation Instructions with owner• OWNER: Read your dishwasher Use and Care Manual. It contains important safety information for operating this appliance• It also has many suggestions for getting the best results from your dishwasher• Read all instructions Open Door 50¼"(127,6 cm} 2¼"< (5,7 cm)' (See image below) (_ To install using Top Mount Cabinet Clips: Depending on the depth of cabinet, the Top Mount Clip have a break off point that can be removed if necessary. NOTE: Install Top Mount Clips before unit is installed into the cabinet. Screw clips firmly to top brace using screws provided in the literature pack. (See image below) 5. 6. 7. Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to prevent damage to cabinet, dishwasher and floor. Front of door needs to be even with the front of adjoining cabinets. Front levelers should allow 5/16" (0,8 cm) below underside of countertop to top of console. Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 7a. Property Damage Do not solder within 6" (15,24 era) of the water inlet valve. Damage to the plastic parts in the valve may occur. Fig ure 7a _' -- Use care that no sealer, dirt, or other objects Damage to the filter screen may occur. Air Gap enter the valve. Be sure the dishwasher is placed_where the water inlet valve will _e.Fep£rrom freezing, if the valve freezes, it may rupture aria noomng may occur, Electric Water Line 1. 8. Adjust levelers _ up or down Figure until dishwasher is level. See Figure Figure 7b 7b/c. 7e 2. 3. 4. Grounding Flush water line before connecting itto water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water supply at shut-off valve, Route water line to water inlet valve as shown in Figure 4. While firmly pulling water supply line into 90 ° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. Turn on water supply and check for leaks. 2. 3. • _ Figure Figure metal, and connected to the appliance's equipment grounding terminal or Mad. it is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. Do not connect the dishwasher to the power appliance is permanently grounded. All wiring connections must be enclosed This unit has copper lead wires. Remove junction box cover and pull house wiring into junction box. See Figure 9 Use a UL listed conduit connector (not included) at box to stabilize wiring. Connect incoming black lead to dishwasher's black lead, incoming white lead to dishwasher's white lead and incoming green lead to dishwasher's green lead with wire nuts. (See Grounding instruction Warning). Wire nuts must be tight. 8 Instructions: The dishwasher must be connected to a grounded permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors Electrical Supply 1. Shock Hazard Joining should supply until in the junction 3. If you connect to a sink trap,local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 13 An air gap kit is available from a plumbing supply store. (if the drain hose is installed through the floor, an air gap is necessary), If you connect to a disposer, the large end of drain hose will fit. Figure 14 (a) The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. See Figure 14 (b). the box. 4. aluminum building wire to stranded copper wire be done by a qualified electrician using materials recognized by UL and local codes. Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. Failure to follow these instructions could result in death or serious Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury Cut Hazard Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. Failure to follow this warning may result in injury. injury. 9 Larger end fits disposer inlet fitting Figure Option f _ t Green Wire to Green (Ground) He|es need to be pre.drilleld using a 05 drill to secure unit 10. Screw mounting brackets firmly to cabinet using screws provided in installation packet. See Figure 8 11. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly, adjust rear foot if small correction is needed until door opens and closes freely. Adjust the levelling legs. 9. Green Wire to Green Wire . _ Wh'thiW'_/_/ire_ Black Wire to Black Wire Cut Gap f_ Sink BlackWire ! !_kWire _/ X _, at Left White Wire to White Wire "X_f (Neutral) Replace junction box cover.See Figure Figure 10 Through Fl_rimo 10 Separate Trap Removg Sink = Review Figures 12, 13 and 14 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. Figure Figure 5. Entry Must be Above Trap 11 6. _V_ Branch Tailpiece 7. Water Line Electrical Line Sink at Right Sink at Left Figure The drain to insure All three leg levelers are positioned Cabinet Seals are positioned dishwasher. [] properly. on the sides of the Cabinet Attachment Clips are attached to the cabinet on both corners on top of the dishwasher. j 2"Drain Hose Hole 12 hose loop must be at least 32" (80 cm) high from proper 14(b) at Right 2" (5,08 cm) Drain Hose Hole The drain hose loop must be at least 32"(80 cm) high from the floor to insure proper Water and electrical lines are straight out in front of the dishwasher. [] Water and drain lines have no kinks and move freely behind the dishwasher. [] Water supply n Joints are free of leaks. [] Wiring connections to junction panels are secured back in place. (Hot) 4, Plug in Disposer [] check these items: Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kick#ate assembly before placing unit into operation. Failure to follow this warning could result in electric shock. %"(1,6 era) connection. _J_@_ ,f_ (Ground/ . 14(a) 8. 2. if you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 12, kickplate. [] Drain [] All packing materials been removed from [] Dishwasher [] Open hose on. box are tight all access See Figure is connected 11 properly and consumer inside unit. is level and securely and close door to make cabinet to outlet. literature have fastened. sure it does not hit or countertop. Make gqre that all wire ties are removed assemDly from the rack Operate the machine through at least one fill and pump-out, checking the following items: [] At first fill, approximately 4 minutes make sure water completely covers filter surface. [] At pump-out: (pump-out is either when the cycle is completed or canceled, refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out. Check water connections again for leaks. the floor drainage. Replace [] If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. Secure drain hose to sink drain, disposer, or separate trap with a clamp, iMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. Be sure unit does not rest on drain hose. it should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. [] surrounding drainage. is turned []
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Sat Feb 14 07:04:10 2015 Author : Title : Subject :EXIF Metadata provided by EXIF.tools