Frigidaire FWT449GFS2 User Manual WASHER Manuals And Guides L0710661

FRIGIDAIRE Residential Washers Manual L0710661 FRIGIDAIRE Residential Washers Owner's Manual, FRIGIDAIRE Residential Washers installation guides

User Manual: Frigidaire FWT449GFS2 FWT449GFS2 FRIGIDAIRE WASHER - Manuals and Guides View the owners manual for your FRIGIDAIRE WASHER #FWT449GFS2. Home:Laundry & Garment Care Parts:Frigidaire Parts:Frigidaire WASHER Manual

Open the PDF directly: View PDF PDF.
Page Count: 6

Installation
Instructions
Full Size Tumble Action Washers
Before beginning installation, carefully read these instructions• This will simplify the
installation and ensure the washer is installed correctly and safely• Leave these instructions
near the washer after installation for future reference•
NOTE: The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70 or in Canada, CSA
C22•1 Canadian Electrical Code Part 1• Contents
For your safety the information in
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or loss of life.
- Do not store or use gasoline or other
flammable vapors and liquid in the vicinity of
this or any other appliance.
- WHATTO DO IFYOU SMELL GAS
•Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppliers
instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
SUBJECT PAGE
Pre-tnstallation Requirements 2
Electrical Requirements 2
Grounding Requirements 2
Water Supply Requirements 2
Drain Requirements 2
Rough-In Dimensions 3
Location Of Your Washer 4
Unpacking 4
Installation 5
Replacement Parts 5
Printed in U.S.A. PIN 131803200 (9811 )
PRE-INSTALLATION REQUIREMENTS
Tools Required for Installation:
1. 1/4 in. nut driver
2. 3/8 in. socket with ratchet.
3. 3/8 in. open end wrench.
4. 7/16 in. socket with ratchet.
5. 9/16 in. open end wrench.
6. Channel-lock adjustable pliers.
7. Carpenter's level.
ELECTRICAL REQUIREMENTS
CIRCUIT - Individual, properly polarized and grounded
15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.
POWER SUPPLY - 2 wire, with ground, 120 volt, single
phase, 60 Hz, Alternating Current.
OUTLET RECEPTACLE - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.
GROUNDING REQUIREMENTS
Improper connection of the equipment grounding
conductor can result in a risk of electrical shock. Check
with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least
resistance for electrical current.
.Since your washer is equipped with a power
supply cord having an equipment-grounding
conductor and a grounding plug, the plug MUST
be plugged into an appropriate, copper wired
receptacle that is properly installed and grounded
in accordance with all local codes and ordinances
or in the absence of local codes, with the National
Electrical Codes, ANSI/NFPA 70 (latest edition).
If in doubt, call a licensed electrician. DO NOT
cut off or alter the grounding prong on the power
supply cord. In situations where a two-slot
receptacle is present, it is the owner's
responsibility to have a licensed electrician
replace it with a properly grounded three prong
grounding type receptacle.
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed within
42 inches (107 cm) of your washer's water inlet. The
faucets MUST be 3/4 inch (1.9 cm) garden hose type
so inlet hoses can be connected. Water pressure
MUST be between 10 and 120 pounds per square
inch (maximum unbalance pressure, hot vs. cold, 10
psi.) Your water department can advise you of your
water pressure. The hot water temperature should be
about 120 degrees F (49 degrees C).
DRAIN REQUIREMENTS
1. Drain capable of eliminating 17 gals (64.3 L) per
minute.
2. A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.
3. The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm) t
96 in.
(244 cm)
o Max.
- t
24 in.
(61 cm)
Min.
BACK l
NOTE:
Drain hose attached to the washer can reach a
58 in. (147 cm) high standpipe. For higher
standpipe use hose P/N 131461201, available
from an authorized parts distributor. If drain is
less than 24 in. (61 cm), install a siphon break
kit, available at your local hardware store.
17
(43.2)
(ls%
ROUGH-IN DIMENSIONS
24 3,4
"_ (62.9)
6O
(152.4) _
11/2 V_
Power
Cord
331/2
(85)
36
(91.5)
SIDE
263A
(67.9)
(7 3)
o
/
Under
Counter
345/6
(87.9)
iiiii!
\i
/
/
BACK
inch (cm) Adjustable Legs Roller Wheels
Water
Inlets
31%
(80.3)
UNDER COUNTER INSTALLATION
If an under counter* installation is desired, the washer MUST have a top sheet kit installed, P/N 131445600.
Kit is available from an authorized parts distributor.
*Custom sized countertop is required.
17
(43.2) 3A
inch (cm)
24 8,4
(62.9)
6O
SIDE
iiiii!iiiiii i&
1½
(3.81)
Power
Cord
33½
(85)
AdjustableLegs
43%
(110.7)
26SA
"_ (67.9) _"
O
/
!
\ O A
\
./
\ j) \
, BACK
Roller Wheels
2¼
(7.3)
Water
Inlets
31%
(80.3)
1
LOCATION OF YOUR WASHER
DO NOT INSTALL YOUR WASHER:
1. In an area exposed to dripping water or outside
weather conditions. The ambient temperature
should never be below 60 degrees F (15.6
degrees C) for proper washer operation.
2. In an area where it will come in contact with
curtains or drapes.
3. In an area (garage or garage-type building) where
gasoline of other flammables are kept or stored
(including automobiles).
4. On carpet. Floor MUST be solid with a maximum
slope of 1/2 in. per foot (1.27 cm per 30.5 cm). To
ensure vibration or movement does not occur,
reinforcement of the floor may be necessary.
IMPORTANT
MINIMUM INSTALLATION CLEARANCES
When installed in alcove or closet:
Sides, Rear = 0 in. (0 cm)
Top = 0 in. (0 cm) Front Console Model
Top = 15 in. (38.1 cm) Rear Console Model
When installed in closet: Front = 1 in. (2.54 cm)
Closet door ventilation required: 2 Iouvered openings
each 60 in2(387 cm2), 3 in. (7.6 cm) from top and bottom
of door.
3. Remove the styrofoam base.
4. Carefully return the washer to an upright position
and remove the carton.
5. Carefully move the washer to within 4 feet (122cm)
of the final location.
6. Remove the following from the back side of the
washer: 4 bolts,
4 yellow plastic spacers,
4 metal "P" clamps.
7. Remove the service panel from the front of the
washer.
8. Remove the 4 nuts and 6 large washers that attach
the 2 yellow shipping braces to the drum and the
base. Lift up on the drum and remove the braces
(a yellow ribbon surrounds the items to be
removed). These braces must be removed to allow
the power supply cord to be released from the
shipping ring.
9. Remove the large styrofoam block located under
the drum. Lift up on the drum, tilt the base of the
foam block inwards toward the rear of the washer
until free, then pull it out.
10. Remove and discard the yellow ribbon and label
from the front of the washer.
UNPACKING
1. Cut the shipping carton along the dotted line along
the base of the unit.
2. While in the carton carefully lay the washer on its
back side.
@
BOLT
(_)' SPACER
"P" CLAMP
11. From the rear of the washer, carefully pull out the
power supply cord through the hole in the
backsheet.
12. Replace the service panel and screws.
NOTE: If the washer is to be transported at a later
date, the shipping support hardware must
be reinstalled to prevent shipping
damage. Retain the hardware in the
plastic bag provided.
.
.
.
Cable
Tie
.
INSTALLATION
Run some water from the
hot and cold faucets to flush
the water lines and remove
particles that might clog up
the water valve screens.
Connect the inlet hose ends
to the HOT and COLD water
faucets tightly by hand,
then tighten another 2/3 turn
with pliers. Turn the water on
and check for leaks.
NOTE: Use only new hoses provided with this unit.
Carefully move the washer to its final location.
Rollers on the rear of the washer allow for easy
movement in undercounter installations. Gently
lift up on the front of the washer and slide back.
NOTE: Lifting up more than 1/8" will engage the
rear legs. Do not use the dispenser drawer
or door to lift washer.
With the washer in its final position, place a level
on top of the washer (if an undercounter
installation, no rocking of the washer should exist).
Adjust the front leveling legs up or down to ensure
the washer is resting solid. Turn the lock nuts on
each leg up towards the base of the washer and
snug with a wrench.
NOTE: Keep the leg extension at a minimum to
prevent excessive vibration. The farther
out the legs are extended the more the
washer will vibrate.
The washer is designed to operate resting on its
rear rollers, tfthe floor is not level or is damaged,
the rear leveling legs may have to be extended.
For undercounter installations, rear leg adjustment
is accessible through the front service panel.
Form a U shape on the end of the drain hose with
the hose pointed toward the drain. Place in a
laundry tub or standpipe and secure with the cable
tie provided in the enclosure package.
NOTE: If the drain hose is placed in a standpipe
without forming a U shape, a siphoning
action could occur. There must be an air
gap around the drain hose. A snug hose
fit can also cause a siphoning action.
@
Cable Tie
Cable
Tie
Cable
Tie
6. Plug the power cord into a grounded outlet.
NOTE: Check to ensure the power is off at a
circuit breaker/fuse box before plugging
the power cord into an outlet.
7. Turn on the power at a circuit breaker/fuse box.
8. Read the Operating Instructions and Owner's
Guide provided with the washer. They contain
valuable and helpful information that will save you
time and money.
9. Run the washer through a complete cycle. Check
for water leaks and proper operation.
10. If your washer does not operate, please review
the "Avoid Service Checklist" in your Owner's
Guide before calling for service.
11. Place these instructions in a location near the
washer for future reference.
NOTE: A wiring diagram is located inside the washer
on the service panel.
REPLACEMENT PARTS
If replacements parts are needed for your washer,
contact the source where you purchased your washer
or call 1-800-944-9044 for the Frigidaire Company
Authorized Parts Distributor nearest you.
Destroy the carton and plastic bags
after the washer is unpacked. Children might use them
for play. Cartons covered with rugs, bedspreads, or
plastic sheets can become airtight chambers causing
suffocation. Place all materials in a garbage container
or make materials inaccessible to children.
_The instructions in this manual and all
other literature included with this washer are not meant
to cover every possible condition and situation that
may occur. Good safe practice and caution MUST be
applied when installing, operating and maintaining any
appliance.
Maximum benefits and enjoyment are achieved
when all the Safety and Operating instructions are
understood and practiced as a routine with your
laundering tasks.
[DO NOT PRINT
P/N 131803200 mEnglish Page 6 left intentionally blank.]

Navigation menu