Fujifilm Finepix A204 Users Manual Owner's

A204 to the manual 92666ce8-2633-4bda-bceb-30a629df2997

2015-02-02

: Fujifilm Fujifilm-Finepix-A204-Users-Manual-402935 fujifilm-finepix-a204-users-manual-402935 fujifilm pdf

Open the PDF directly: View PDF PDF.
Page Count: 64

2.0
A204 BL00202-200 (1)
7
8
Getting Ready
Camera Connection
Using FinePixViewer
Basic Photography
Advanced Features
Photography
Advanced Features
Playback
Software Installation
Settings
32
Warning
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing)instructions
in the literature accompanying the
appliance.
For customers in the U.S.A.
FCC Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions : (1)This device may not cause
harmful interference, and (2)this device must
accept any interference received, including
interference that may cause undesired
operation.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The graphical symbols are located on the bottom
of the case.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
CAUTION
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures :
—Reorient or relocate the receiving antenna.
—Increase the separation between the
equipment and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Please read the Safety Notes (➡P.119)
and make sure you understand them
before using the camera.
—Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void the user’s authority to operate
the equipment.
Notes on the Grant:
To comply with Part 15 of the FCC rules, this
product must be used with a Fujifilm-specified
ferrite-core USB cable and DC supply cord.
For customers in Canada
CAUTION
This Class B digital apparatus complies with
Canadian ICES-003.
4
1
2
3
4
5
6
7
8
5
4 Advanced Features Playback
PLAYING BACK MOVIES ........................................ 52
■Playing Back Movies ..................................... 53
w
MODE
5 Settings
6 Software Installation
g
ADJUSTING THE MONITOR BRIGHTNESS
......... 67
gUSING SET–UP .................................................. 68
■List of settings ................................................ 69
■SET–UP Menu Options ................................. 69
gPOWER SAVE .................................................... 70
SET–UP
System Expansion Options ................................ 101
Accessories Guide ............................................. 102
Notes on Using Your Camera Correctly ............. 104
Notes on the Power Supply ................................ 105
Applicable Batteries ...................................... 105
Notes on the Batteries .................................. 105
AC Power Adapter ........................................ 107
Notes on the xD-Picture Card ............................ 108
Warning Displays ............................................... 110
Troubleshooting .................................................. 113
Specifications ..................................................... 116
Explanation of Terms ......................................... 118
Safety Notes ....................................................... 119
EC Declaration of Conformity ............................. 123
IMPORTANT ...................................................... 124
6.1 The Software Components ................................. 71
6.2 Installation on a Windows PC ............................. 72
6.2.1 Load the CD-ROM into your PC ................ 72
6.2.2
From FinePixViewer installation to restart
....... 73
6.3 Installation on a Mac OS 8.6 to 9.2 .................... 77
6.3.1 Check the system software settings .......... 77
6.3.2 From FinePixViewer installation to restart .. 77
6.4 Installation on a Mac OS X ................................. 80
6.4.1 From FinePixViewer installation to restart .. 80
7 Camera Connection
7.1 Using the optional AC Power adapter ................ 83
7.2 Use at DSC mode ............................................... 84
8 Using FinePixViewer
8.1
Saving Images on Your Computer and viewing images
.. 92
8.2 Making a FinePix CD Album ............................... 93
8.3 Using the FinePix Internet Service ..................... 94
8.3.1 User FAQ ................................................... 94
8.3.2 User Registration ....................................... 94
8.4 Mastering FinePixViewer .................................... 98
8.5 Uninstalling the Software .................................... 99
Contents
1 Getting Ready
2 Basic Photography
3 Advanced Features Photography
LOADING THE BATTERIES AND xD-Picture Card
..... 11
Compatible batteries ......................................... 11
xD-Picture Card (sold separately) ..................... 11
SWITCHING ON AND OFF ...................................... 14
SETTING THE DATE AND TIME ............................. 15
Changing the date and time .............................. 16
To change the date display format .................... 17
SELECTING THE LANGUAGE ................................ 18
Warning .................................................................. 2
Preface ................................................................... 6
Accessories and Attaching the Strap ..................... 7
Nomenclature ......................................................... 8
BASIC OPERATION GUIDE .................................... 19
TAKING PICTURES (AAUTO MODE) .................. 21
■Viewfinder Lamp Display ............................... 25
Number of Available Frames ............................. 26
USING AF/AE LOCK ................................................ 27
USING THE ZOOM .................................................. 29
FRAMING GUIDELINE FUNCTION ......................... 30
VIEWING YOUR IMAGES (PLAYBACK) ................. 31
MULTI-FRAME PLAYBACK ..................................... 32
PLAYBACK ZOOM ................................................... 33
w
MODE
Q
MODE
SELECTING AAUTO OR SMANUAL .............. 36
PHOTOGRAPHY MENU OPERATION .................... 37
PHOTOGRAPHY AND MOVIE MENU OPTIONS
... 38
ySETTING THE QUALITY .................................. 39
cFLASH ............................................................... 40
AUTO
Auto Flash Mode ...................................... 40
nRed-Eye Reduction .................................. 41
cForced Flash ............................................ 41
bSuppressed Flash .................................... 42
vSlow Synchro ........................................... 42
EMACRO (CLOSE-UP) PHOTOGRAPHY .......... 43
=SELF-TIMER PHOTOGRAPHY ........................ 44
aWHITE BALANCE
(SELECTING THE LIGHT SOURCE) ............... 46
dEV (EXPOSURE COMPENSATION) ................ 47
TMOVIE (VIDEO) ................................................ 48
■xD-Picture Card standard shooting time ........ 48
Quality settings for movies ................................ 51
T
MODE
PHOTOGRAPHY MENU
Q
MODE
7.3 Use at PC-CAM mode ........................................ 87
7.4 Disconnecting the Camera ................................. 90
ERASING SINGLE FRAME ...................................... 34
pERASING SINGLE •
ALL FRAMES/FORMATTING .......................... 54
kPROTECTING IMAGES FRAME/ALL .............. 58
i
HOW TO SPECIFY PRINT OPTIONS (DPOF)
....... 62
iDPOF SET FRAME .......................................... 63
PLAYBACK MENU
6 7
Accessories
h16 MB, xD-Picture Card (1)
Supplied with:
• Anti-static case (1)
hLR6 AA-size alkaline Batteries (2)
hHand strap (1)
hUSB Interface Set (1)
• CD-ROM: Software for FinePix SX (1)
• USB cable with Noise Suppression core (1)
hOwner’s Manual (this manual)(
1)
1Pass the loop of this cord on the end of the
strap through the strap mount.
2Then pass the other end of the strap through
the loop of the thin cord and pull the strap
tight.
Attaching the Strap
0102
Preface Accessories and Attaching the Strap
■Test Shots Prior to Photography
For particularly important photographs (such as weddings and
overseas trips), always take a test photograph and view the
image to make sure that the camera is functioning normally.
hFuji Photo Film Co., Ltd. cannot accept liability for any
incidental losses (such as the cost of photography or the
loss of income from photography) incurred as a result of
faults with this product.
■Notes on Copyright
Images recorded using your digital camera system cannot be
used in ways that infringe copyright laws without the consent
of the owner, unless intended only for personal use. Note that
some restrictions apply to the photographing of stage
performances, entertainments and exhibits, even when
intended purely for personal use. Users are also asked to note
that the transfer of memory cards containing images or data
protected under copyright laws is only permissible within the
restrictions imposed by those copyright laws.
■Liquid Crystal
If the LCD monitor or display panel is damaged, take particular
care with the liquid crystal in the monitor or panel. If any of the
following situations arise, take the urgent action indicated.
hIf liquid crystal comes in contact with your skin
Wipe the area with a cloth and then wash thoroughly with
running water and soap.
hIf liquid crystal gets into your eye
Flush the affected eye with clean water for at least
15 minutes and then seek medical assistance.
hIf liquid crystal is swallowed
Flush your mouth thoroughly with water. Drink large
quantities of water and induce vomiting. Then seek
medical assistance.
■Notes on Electrical Interference
If the camera is to be used in hospitals or aircrafts, please
note that this camera may cause interference to other
equipment in the hospital or aircraft. For details, please
check with the applicable regulations.
■Handling Your Digital Camera
This camera contains precision electronic components. To
ensure that images are recorded correctly, do not subject the
camera to impact or shock while an image is being recorded.
■Trademark Information
hIBM PC/AT is a registered trademark of International
Business Machines Corp. of the U.S.
hiMac and Macintosh are registered trademarks of Apple
Computer, Inc.
hQuickTime and the QuickTime logo are trademarks used
under license. The QuickTime logo is registered in the
U.S. and other countries.
hAdobe Acrobat®Reader™is a trademark of Adobe
Systems Incorporated of the U.S.
hMicrosoft , Windows, the Windows logo and DirectX are
either trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Windows is an abbreviated term referring to the Microsoft
Windows Operating System.
✽The “Designed for Microsoft Windows XP” logo refers to
the camera and the driver only.
hxD-Picture Card and other company or product names are
trademarks or registered trademarks of the respective
companies.
■ Exif Print (Exif ver. 2.2)
Exif Print Format is a newly revised digital camera file format that
contains a variety of shooting information for optimal printing.
98
MENU/OK button(P.19)
DISP button(P.19,30,32)
BACK button (P.19)
Strap mount(P.7)
xD-Picture Card slot
(P.13)
Viewfinder lamp(P.14)
Viewfinder(P.23)
LCD monitor
(P.23)
Tr ipod mount
Battery cover
(P.12,13)
Battery compartment
  (a)  (b)
/Zoom button
g button
Nomenclature ✽Refer to the pages in parentheses for information on using the camera features.
Flash(P.40)
Shutter button
Lens
Self-timer lamp
(P.45)
Viewfinder window
(USB) socket
(P.84,87)
DC IN 3V
(Power input)
socket (P.83)
POWER switch(P.14)
Lens cover(P.14)
Mode Switch
Flash control sensor
Movie mode(P.48)
  Still photography mode(P.21)
Select this mode for still photography.
Playback mode(P.31)
This mode provides playback zoom and multi-frame
playback as well as normal single-frame playback.
You can also use this mode to erase frames, format
xD-Picture Card and specify DPOF settings.
11
1
10
1Getting Ready
LOADING THE BATTERIES AND xD-Picture Card
xD-Picture Card (sold separately)
DPC-16 (16MB)
DPC-64 (64MB)
DPC-32 (32MB)
DPC-128 (128MB)
●
!
Operation of this camera is only guaranteed when it
is used with FUJIFILM xD-Picture Card.
●
!
Because xD-Picture Cards are small, they can be
accidentally swallowed by small children. Be sure to
store xD-Picture Cards out of the reach of small
children. If a child accidentally swallows an xD-Picture
Card, seek medical advice immediately.
●
!
See P.108-109 for more information on xD-Picture
Card.
Compatible batteries
Use two AA-size alkaline batteries or two AA-
size nickel-metal hydride (Ni-MH) batteries.
◆Notes on Handling Batteries ◆
hIt is recommended that you use the same brand of
alkaline batteries as those supplied with the camera.
hNever use a battery when the
outer casing is split or peeling as
this could result in a short-circuit
and cause major problems due
to battery fluid leakage or
overheating.
hDo not use different types of batteries or old and new
batteries together.
hYou cannot use lithium, manganese or nickel-
cadmium (Ni-Cd) batteries.
hThe operating lives of alkaline batteries vary between
brands and the life of batteries you purchase may be
shorter than the alkaline batteries provided with the
camera. Note also that due to the nature of alkaline
batteries, the time for which they can be used is
shorter in cold locations (at temperatures of +10°C
(+50°F) or below). Consequently, Ni-MH batteries are
recommended.
hSoil (fingerprints, etc) on the terminals of batteries can
greatly reduce the time for which the batteries provide
power.
hYou will need the optional charger (➡P.102) to
recharge Ni-MH batteries.
hSee P.105 for notes on using batteries.
Outer casing
Nomenclature (Sample display)
Battery level warning
Protection
DPOF
Playback mode Playback frame number
Macro
Number of remaining shots
Camera shake warning
AF warning
Battery level warning
Quality mode
EV(Exposure compensation)
White balance
Flash
Still photography mode
Zoom bar
Date
Date
AF frame
 １／ １／２００２
 １／ １／２００２
１００ー０００１
１００ー０００１
４９
４９
 １／ １／２００２
 １／ １／２００２
１Ｍ
１Ｍ
ＡＦ
ＡＦ
Example of LCD Monitor Text Display: Still photography mode
Example of LCD Monitor Text Display: Playback mode
Front Back
12 13
1
Indicator
◆Replacing an xD-Picture Card ◆
When you push the xD-Picture Card into the slot
and then slowly remove your finger, the lock is
released and the xD-Picture Card is pushed out.
You can then pull the xD-Picture Card the rest of
the way out.
3Push the xD-Picture Card firmly into the
xD-Picture Card slot as far as it will go.
4Close the battery cover.
●
!
If you open the battery cover while the camera is still
switched on, the camera is automatically switched
off to protect the xD-Picture Card.
●
!
The xD-Picture Card will not slide fully into the slot if
it is inserted facing the wrong way. Be careful not to
apply undue force to the xD-Picture Card.
●
!
When storing xD-Picture Card, always use the anti-
static case provided.
●
!
Take care not to remove your finger too quickly
after the lock is released, as the card may
spring completely out of the slot.
0304
1Slide the battery cover out to open it.
2Load the batteries correctly as shown.
●
!
Do not apply excessive force to the battery cover.
LOADING THE BATTERIES AND xD-Picture Card
0102
Do not open the battery cover while the camera
is still switched on. This could damage the xD-
Picture Card or corrupt the image files on the
xD-Picture Card .
◆When you want to replace
the battery ◆
●
!
Take care not to drop the battery when opening
and closing the battery cover.
Check that the camera is switched off, open the
battery cover and then remove the battery.
Indicator
14 15
1
SETTING THE DATE AND TIME
●
!
To set the date and time later, press the “BACK”
button.
●
!
If you do not set the date and time, this confirmation
screen will appear each time you switch the camera on.
When you first switch the camera on, the date is
cleared. Press the “MENU/OK” button to set the
date and time.
1
1Use “d” or “c” to select Year, Month, Day,
Hour or Minute.
2Press “a” or “b” to set the number.
●
!
If you hold down “a” or “b”, the numbers change
continuously.
●
!
When the time displayed passes “12:00”, the AM/PM
setting automatically switches.
2
0102
When you slide the “POWER” switch sideways
to switch the camera on, the green viewfinder
lamp lights. To switch the camera off, slide the
“POWER” switch sideways again.
1Use the Mode switch to select the mode you
want to use.
2If you want to use the camera in Still
photography/Movie mode, open the lens cover.
If the “ç” warning message
appears on the LCD monitor, slide the lens
cover completely.
●
!
Take care not to press on the lens when it is
extending or while you are taking a shot as this could
cause a camera fault.
●
!
Open and close the lens cover by fitting your finger
into the indentation in the cover.
1 2
01
02
SWITCHING ON AND OFF
16 17
1
To change the date display format
◆Power Save Function ◆
If the camera is not used for 2 minutes, this
function automatically switches it off.
When this function is enabled, the LCD monitor
switches off to conserve battery power if the
camera is not used in any way for 30 seconds
(See P.70 for details).
◆Checking the remaining battery charge ◆
Switch the camera on and check that no battery
level warning (Zor X) is displayed on the
LCD monitor. If no icon indicating the remaining
battery charge is displayed, the battery has
ample charge.
iZLit red:
Battery charge low. Replace or recharge the
battery as it will run out shortly.
iXBlinking red:
The battery is exhausted. The display will shortly
go blank and the camera will stop working.
Replace or recharge the battery.
●
!
The above estimates are for the Still photography
modes. In Playback mode, the transition from “Z”
to “X” may take less time.
0102
1Press “d” or “c” to select the date format.
2Press “a” or “b” to set the format. Refer to
the table below for details of the settings.
Displays the date in the “month/day/ year” format.
MM/DD/YYYY
Displays the date in the “day.month. year” format.
DD.MM.YYYY
YYYY.MM.DD
Explanation
Setting
Displays the date in the “year.month. day” format.
Once you have set the date and time, press the
“MENU/OK” button. Pressing the “MENU/OK”
button switches the camera to still photography
or Playback mode.
●
!
You cannot set the seconds, but you can set the time
more accurately by pressing the “MENU/OK” button
when the time on your reference clock is at zero
seconds.
●
!
If the camera is left for 30 minutes or longer with the
batteries removed and the AC power adapter
disconnected, the date and time settings may revert to
the factory default settings. If this occurs, reset the date
and time.
3
Changing the date and time
To change the date and time:
1Press the “MENU/OK” button.
2Use “d” or “c” to select “g” OPTION and
then use “a” or “b” to select “SET–UP”.
3Press the “MENU/OK” button.
4Select “DATE/TIME” and press “c”.
See P.15 for information on setting the date and
time.
01030204
SETTING THE DATE AND TIME
19
2
18
2Basic
Photography BASIC OPERATION GUIDE
You can use this button to
select the LCD monitor display
mode.
When shooting : Switches
the LCD monitor on and off
or displays the framing guides.
During playback : Switches
text display on and off or selects
multi-frame playback.
Slide this switch to turn the
camera on and off.
0 DISP button
Displays the menu screen
when you are shooting or
playing back images. You also
press this button to confirm a
menu selection.
0 MENU/OK button
Press this button to stop a
procedure midway through.
0 BACK button
0 POWER switch 0 Switching between still
photography,playback
and movies
0 Main actions performed
by a, b, dand c
For recording still images.
Still photography
For playing back recorded
data.
Playback
For recording movies.
Movie
Change frame in playback.
gbutton ：
fbutton ：
Digital zoom, Playback
zoom.
SELECTING THE LANGUAGE
1Press the “MENU/OK” button to display the
menu screen.
2Use “a”, “b”, “d” or “c” to select “SET–UP”
from the “g” OPTION menu.
3Press the “MENU/OK” button.
1The “SET–UP” screen appears. Use “a” or
“b” to select “LANGUAGE”.
2Use “c” to select “ENGLISH”, “FRANCAIS” or
“DEUTSCH”. You can cycle through the
language settings by pressing “c”.
0102
21 0301
02
●
!
The screens in this manual are shown in English.
●
!
See P.68 for more information on the “g” OPTION
menu.
20 21
2
1Set the Mode switch to “Q”.
2Open the lens cover. If the “ç”
warning message appears on the LCD
monitor, slide the lens cover completely.
3Slide the “POWER” switch sideways to switch
the camera on.
To take pictures using the LCD monitor, press
the “DISP” button to switch the LCD monitor on.
hFocal range: Approx. 80 cm (2.6 ft.) to infinity
1 2
●
!
If the “Ω”, “∂”, “≈” or
“˙” message appears, see P.110.
01
03
02
Loop the strap over your wrist, brace your
elbows firmly against your body and hold the
camera with both hands.
●
!
For subjects closer than 80 cm (2.6 ft.), use Macro
photography (➡P.43).
●
!
To minimize power consumption, you should use the
viewfinder (switch the LCD monitor off) to take pictures.
●
!
Use a tripod to avoid camera shake, particularly for
shots is dark situations when the flash is set to
Suppressed Flash mode (➡P.40).
BASIC OPERATION GUIDE
●Using the Menus
1Display the menu.
Press the “MENU/OK” button.
2Select a menu option.
Press the “d” or “c”.
Press this button to stop
a procedure midway
through.
Help messages are displayed at the bottom of
the screen to show you the next step to take.
Press the button indicated.
Press the “DISP” button
to use the zoom.
In the Owner's Manual,black triangles
are used to indicate up,down (a,b )
and left, right (d,c) respectively.
3Select a setting.
Press the “a” or “b”.
◆ Displaying the On-screen Help ◆
4Confirm your selection.
Press the “MENU/OK” button.
ＺＯＯＭ
ＤＩＳＰ
ＺＯＯＭＺＯＯＭ
ＤＩＳＰ
１Ｍ １Ｍ １Ｍ １Ｍ
  ２５
  ３９
２Ｍ Ｆ
２Ｍ Ｎ
 １２２
０ ３Ｍ
  ４９
ＱＵＡＬＩＴＹ
１Ｍ １Ｍ １Ｍ １Ｍ
  ２５
  ３９
２Ｍ Ｆ
２Ｍ Ｎ
 １２２
０ ３Ｍ
  ４９
ＱＵＡＬＩＴＹ
TAKING PICTURES (AAUTO MODE)
QMODE
22 23
2
Using the viewfinder or LCD monitor, frame your
shot so that the subject fills the entire AF (Auto
Focus) frame.
●
!
If your subject is not in the center of the picture, use
AF/AE lock to take the picture(➡P.27).
When you are using the viewfinder to take a
picture at a distance of 0.8 m to 1.5 m (2.6 ft. to
4.9 ft.), only the shaded area in the figure is
photographed.
5
6
LCD monitor
AF frame
AF frame
Viewfinder ●
!
To frame your shot precisely, you should take the
picture using the LCD monitor.
●
!
In some conditions it may be difficult to see your
subject clearly on the LCD monitor, such as in sunny
weather outdoors or when you are shooting dimly lit
scenes. In such situations, use the viewfinder to take
the shot.
●
!
The image shown on the LCD monitor before you
take the shot may differ in its brightness, color, etc.
from the image actually recorded. If necessary, play
back the recorded image to check it (➡P.31).
Ensure that your fingers or the camera strap do
not obscure the lens or flash control sensor.
●
!
There may be some unevenness in the brightness at
the lower edge of the LCD monitor. This is normal
and does not indicate a fault. This does not affect
the photographed image.
●
!
Check that the lens is clean. If it is dirty, clean the
lens as described on P.104.
●
!
If you use the flash in very dusty conditions or when
it is snowing, white dots may appear in the image
due to the flash reflecting off the dust particles or
snowflakes. Try taking the shot with the flash mode
set to Suppressed Flash.
To zoom in on the subject, press “a” (}TELE).
To zoom out, press “b” ({WIDE). A “zoom
bar” appears on the LCD monitor when you
zoom in or out.
●Optical zoom focal length (35mm camera
equivalent)
Approx. 38 mm-114 mm (1.5 in. to 4.5 in.)
Maximum zoom scale: 3×
●
!
Zooming stops briefly when the camera switches
between optical zoom and digital zoom (➡P.29).
3 44
TAKING PICTURES (AAUTO MODE)
QMODE
24 25
2
■Viewfinder Lamp Display ✽When the LCD monitor is switched on, more detailed warning messages
are displayed (➡P.110-112).
Display Status
Lit green Ready to shoot
.
Blinking green
AF/AE in progress, camera shake warning or AF warning (Ready to shoot).
Blinking green and
orange alternately
Recording to xD-Picture Card (Ready to shoot).
Lit orange Recording to xD-Picture Card (Not ready).
Blinking orange Flash charging. PC communication in progress (Flash will not fire).
Blinking red hxD-Picture Card Warnings
No card loaded, card not formatted, incorrect format, card full, xD-Picture Card error.
hLens operation error.
hVery shiny subjects such as a mirror or car body.
hSubjects photographed through glass.
hSubjects that do not reflect well, such as hair or fur.
hSubjects with no substance, such as smoke or flames.
hWhen the subject is dark.
hWhen there is very little contrast between the subject
and the background (such as white walls or subjects
dressed in the same color as the background).
◆ Subjects Not Suitable for Autofocus ◆
hSubjects moving at high speed.
hWhen something other than your subject is close to the
AF frame, has contrasting areas of light and dark and is
either closer or further away than your subject (as when
you photograph someone against a background with
strongly contrasting elements).
For subjects of this type, use AF/AE lock (➡P.27).
Though the FinePix A204 uses an accurate autofocus mechanism, it may have difficulty focusing or not be able to
focus at all for the types of subject and situation listed below. In such cases, the image may be out of focus.
7
To take the picture, press the shutter button
down fully without lifting your finger off it. The
camera beeps and takes the picture, and the
data is then recorded.
●
!
When you press the shutter button, there is a very
short delay before the picture is actually taken.
●
!
Since the amount of image data recorded is not fixed
and varies depending on the subject (level of image
detail, etc.), the number of available shots may not
decrease after the image is recorded, or may
decrease by 2.
●
!
See P.110-112 for information on the warning
displays.
7Beep
8
Press the shutter button down halfway. The
camera is focused when the AF frame on the
LCD monitor shrinks and the green viewfinder
lamp stops flashing and stays lit.
●
!
If you press the shutter button down fully in one motion,
the shot is taken without the AF frame changing.
●
!
The viewfinder lamp flashes orange while the flash is
charging. If the LCD monitor is switched on, the
screen may go dark for a moment. This is normal
and does not indicate a fault.
●
!
The flash charging time may increase when the
battery charge decreases.
The viewfinder lamp glows orange while the
image is being recorded and no pictures can be
taken. Also, do not switch the camera off or
open the battery cover during image recording.
Opening the cover during image recording could
corrupt the image files.
TAKING PICTURES (AAUTO MODE)
QMODE
26 27
2
In a shot with this type of composition, the
subjects (two people in this case) are not in the
AF frame. If the shot is taken at this point, the
subjects will not be in focus.
Move the camera slightly so that one of the
subjects in the AF frame.
1
2
USING AF/AE LOCK
QMODE
◆AF (Autofocus)/AE (Auto exposure) Lock ◆
On the FinePix A204, when you press the shutter button down half way, the focus and exposure settings
are fixed (AF/AE lock). If you want to focus on a subject that is off to one side of the image or if you want
to set the exposure before you compose the final shot, lock the AF and AE settings and then compose
and shoot your picture to get the best results.
Continued over page...
✽Number of available shots displayed on the camera for a new xD-Picture Card formatted in the camera.
４９４９
１Ｍ１Ｍ １Ｍ１Ｍ
Number of Available Frames
■ Standard number of shots per xD-Picture Card
Because the amount of data recorded varies depending on the subject, the number of available shots may not
decrease when recording ends, or may decrease by 2 frames. The discrepancy between the standard number of
available shots and the actual number of available shots increases in proportion to the capacity of the xD-Picture Card.
The number of available shots is displayed on
the LCD monitor.
●
!
See P.39 for information on changing the quality.
●
!
The default quality setting “y” set at shipment is
1M.
Quality mode
Image Data Size
DPC-16 (16 MB)
DPC-32 (32 MB)
Approx. 620 KB Approx. 390 KB
2M •F2M
•N
DPC-64 (64 MB)
DPC-128 (128 MB)
101
204
50
25
159
319
79
39
Number of recorded pixels
1600 ×1200 640 ×480
49
99
122
247
Approx. 320 KB Approx. 130 KB
198
398
497
997
1280 ×960
1M 0.3M
TAKING PICTURES (AAUTO MODE)
QMODE
28 29
2
USING THE ZOOM
QMODE
Press “a” to zoom in and make your subject
larger. Press “b” when you want to zoom out
and shoot a wider area. If you use the LCD
monitor to take pictures, you can continue
zooming with the digital zoom after the optical
zoom finishes.
●
!
See P.39 for information on changing the quality
setting.
●
!
If the image goes out of focus when you use the
zoom, press the shutter button down halfway to
refocus.
●
!
The optical zoom is equivalent to approximately
38 mm-114 mm on a 35 mm camera.
The position of the “■” on the zoom bar indicates
the current zoom setting.
hIf the “■” is above the dividing line, the digital
zoom is being used. If it is below the line, the
optical zoom is being used.
hPress “a” or “b” to move the “■” up and down.
hWhen you switch between digital zoom and
optical zoom, the “■” stops moving briefly.
Press the button for the same direction again
to start the “■” moving and switch the zoom
setting.
１Ｍ
１Ｍ
Macro
Macro
０３Ｍ
０３Ｍ
Optical zoom
Digital zoom
Zoom bar display
Digital zoom focal distance✽
Mode
Quality Max.
Zoom Scale
Max. 1.3×
Max. 2.5×
Max. 1.3×
Equivalent to approx. 114 mm-146 mm
Equivalent to approx. 114 mm-285 mm
Equivalent to approx. 38 mm- 48 mm
Still
photography
E
Macro
1M
Cannot be used2M
0.3M
1M
Max. 2.5×
Equivalent to approx. 38 mm- 95 mm
0.3M
✽35 mm camera equivalent
Without moving the camera, press the shutter
button down halfway (AF/AE lock). Check that
the AF frame on the LCD monitor has shrunk
and the green viewfinder lamp has stopped
flashing and is now lit.
Continue to hold the shutter button down
halfway. Move the camera back to the original
image and then fully press down on the shutter
button.
●
!
You can reapply the AF/AE lock as many times as
you like before releasing the shutter.
●
!
The AF/AE lock operates in all photography modes
and can be used to ensure excellent results.
3Beep
4
USING AF/AE LOCK
QMODE
30 31
2
During playback, you can skip backwards or forwards through
the images (the frame number increases or decreases) by
holding down “d” or “c” for approximately 1 second.
The displayed image does not change, but a progress bar
indicates the approximate playback location on the xD-Picture
Card.
1Set the Mode switch to “w”.
2You can “d” or “c” to move forward and
backward respectively through your images.
●
!
When you set the Mode switch to “w”, the last
image shot is displayed.
VIEWING YOUR IMAGES (PLAYBACK)
w
MODE
0102Fast Forwarding Images
Playback frame
number
LCD monitor ON
Framing guideline
displayed
LCD monitor OFF
FRAMING GUIDELINE FUNCTION
Q
MODE
You can select the framing guide function in “Q”
Still photography mode. The mode shown on the
LCD monitor switches each time you press the
“DISP” button. Press the “DISP” button to
display the framing guideline.
●
!
The framing guideline is not recorded on the image.
●
!
The lines in the scene frame roughly divide the
recorded pixels into three parts horizontally and
vertically. When the image is printed, the resulting
print may be shifted slightly from the scene frame.
Scene
Use this frame when you want to position your
main subject in the center of the frame or when
you want to align your shot with the horizon.
This feature provides a clear guide to the
subject size and the overall balance of the shot
so that you get exactly the shot you want.
１Ｍ１Ｍ
４９４９
Always use the AF/AE lock to compose your
picture.
Failing to use the AF/AE lock may result in the
image being out of focus.
◆Important ◆
◆Still images that can be viewed ◆
You can use this camera to view still images recorded on the FinePix A204 or still images (excluding
some uncompressed images) recorded on a FUJIFILM digital camera that supports xD-Picture Cards.
32 33
2
PLAYBACK ZOOM
w
MODE
Pressing “a” or “b” during single-frame
playback zooms in (enlarges) or out on a still
image. When you use this function, a zoom bar
is displayed.
hZoom scales:
2M 1600 ×1200 pixel images: Max 10×
1M 1280 ×960 pixel images: Max 8×
0.3M 640 ×480 pixel images: Max 4×
After you have zoomed in on your image,
1Press the “DISP” button.
2Use “a”, “b”, “d” or “c” to zoom in on different
parts of the image.
3Press the “DISP” button again to revert to
zoomed display.
●
!
Pressing “d” or “c” during zooming cancels zooming
and moves to the next image.
●
!
Multi-frame playback cannot be used with Playback zoom.
●
!
You may not be able to use playback zoom for some
images shot on other camera models.
●
!
Press the “BACK” button to return to normal unscaled
display.
This is useful for such things as checking the focus
after you take a shot.
1
2020301
MULTI-FRAME PLAYBACK
w
MODE
●
!
You cannot use multi-frame playback while a menu
is displayed.
●
!
Playback zoom cannot be used with multi-frame
playback.
In playback mode, the display shown on the
LCD monitor switches each time you press the
“DISP” button. Press the “DISP” button until the
multi-frame playback screen (9 frames) appears.
You cannot display text during multi-frame
playback.
1Select a frame by using “d”, “c”, “a” or “b”
to move the cursor (the orange box) to the
desired frame. Press the “a” or “b” several
times to switch to the previous page or the
next page.
2You can enlarge the selected image by
pressing the “DISP” button again.
No text displayed
Multi-frame
playback
Text displayed
1 2 0102
34 35
2
3
4
Press “d” or “c” to view the frame (individual
file) you want to erase.
●
!
Press the “BACK” button to cancel frame erasing.
Pressing the “MENU/OK” button erases the
frame (individual file) displayed. When erasing is
complete, the next image appears and the
“§” message is displayed.
To erase another frame, repeat steps and .
43
ERASING SINGLE FRAME
w
MODE
1Set the Mode switch to “w”.
2Press the “MENU/OK” button to display the
Menu screen on the LCD monitor.
Select “FRAME” in the “p” ERASE menu and
press the “MENU/OK” button.
See P.54 for more information on “ALL FRAMES”
and “FORMAT”.
1
2
0102
Note that mistakenly erased images cannot be
recovered. You should copy important files that
you do not want to be erased to your computer
or other media.
36 37
3
PHOTOGRAPHY MENU OPERATION
●
!
The settings available in the menu screen differ
depending on the still photography mode.
When you validate the settings, the respective
icons appear at the top of the screen.
2
1Press the “MENU/OK” button to display the
menu.
2Use “d” or “c” to select the menu item and
“a” or “b” to change the setting.
3Press the “MENU/OK” button to confirm the
selection.
1030102
3
Advanced Features
Photography
2030102
1
1Press the “MENU/OK” button to display the
menu.
2Use “d” or “c” to select “g” OPTION and
then use “a” or “b” to select “QAUTO” or
“QMANUAL”.
3Press the “MENU/OK” button to confirm the
selection.
Set the Mode switch to “Q”.
●
!
See P.48 for information on shooting movies.
This is the easiest mode for taking pictures and
can be used in a wide range of conditions.
This mode allows you to specify your own
brightness and white balance settings.
QAUTO
QMANUAL
SELECTING AAUTO OR SMANUAL
Q
MODE
ＱＵＡＬＩＴＹＱＵＡＬＩＴＹ
38 39
3
ySETTING THE QUALITY
PHOTOGRAPHY MENU
✽Displaying the menus (➡P.37)
●
!
The numbers to the right of each setting show the
number of available shots.
●
!
When you change the quality, the number of
available shots also changes.
You can choose from 4 settings. Use the table on
the right as a guide for selecting the best setting
for the shot you want to take.
Printing
Internet
Quality
2M •F(1600 ×1200)
2M •N(1600 ×1200)
1M (1280 ×960)
0.3M ( 640 ×480)
Use
<Examples>
hFor printing on A5 paper →2M •F, 2M •N
✽Select “2M •F” (FINE) for better image quality and
“2M •N” (NORMAL) to increase the number of
available shots.
In most cases, the “2M •N” setting provides more
than adequate image quality.
hFor printing on A6 (postcard) paper →1M
hFor an image attached to E-mail or used on a
website →0.3M
This mode can be selected in the
“A”, “S” still photography
modes.
Number of rem-
aining shots
Factory default
PHOTOGRAPHY AND MOVIE MENU OPTIONS
Mode
AAUTO
yQUALITY
cFLASH
EMACRO
=SELF-TIMER
gOPTION
1M
AUTO
OFF
OFF
–
P.39
P.40
P.43
P.44
P.68
ＱＵＡＬＩＴＹＱＵＡＬＩＴＹ
  ２５  ２５
  ３９  ３９
 １２２ １２２
  ４９  ４９
１Ｍ１Ｍ １Ｍ１Ｍ
２Ｍ・Ｆ２Ｍ・Ｆ
２Ｍ・Ｎ２Ｍ・Ｎ
０３Ｍ０３Ｍ
SMANUAL
yQUALITY
cFLASH
EMACRO
aWHITE BALANCE
dEV
gOPTION
1M
AUTO
OFF
AUTO
0
–
P.39
P.40
P.43
P.46
P.47
P.68
ＥＶＥＶ
０ ３０ ３
０ ３０ ３
０ ６０ ６
＋
−
−
０
TMOVIE yQUALITY
gOPTION
320 ×240
–
P.51
P.68
Sample LCD monitor display Accessible menu settings
Factory default
Explanation
This section gives a quick overview of the various functions you can use when the mode switch is set
to “Q” or “T”.
40 41
3
nRed-Eye Reduction
Use this mode to ensure that the subject’s eyes
appear natural when photographing people in
low-light conditions. The flash fires automatically
as required by the photography conditions.
The flash fires a pre-flash just before the picture
is taken and then fires again to take the actual
picture.
cForced Flash
Use this mode to photograph backlit scenes,
such as a subject against a window or in the
shade of a tree, or to obtain the correct colors
when you are shooting under lighting such as
fluorescent tubes. In this mode, the flash fires in
bright as well as dark conditions.
◆Red-Eye Effect ◆
When you use the flash to photograph people in low-light conditions, their eyes sometimes appear red in
the picture. This is caused by the light of the flash reflecting off the inside of the eye. Use Red-Eye
Reduction flash to effectively minimize the likelihood of the red-eye effect.
Take the following measures also to make Red-Eye Reduction more effective:
●Get the subjects to look at the camera. ●Get as close as possible to the subjects.
cFLASH
PHOTOGRAPHY MENU
Use the flash mode that best suits your shot.
h5 modes: “AUTO”, “n”, “c”, “b” and “v”
hEffective flash range (in “AAUTO” mode):
Wide-angle: Approx. 0.2 m to 3.0 m (0.6 ft. to 9.8 ft.)
Telephoto: Approx. 0.8 m to 3.0 m (2.6 ft. to 9.8 ft.)
●
!
If you use the flash in very dusty conditions or when it is
snowing, white dots may appear in the image due to the flash
reflecting off the dust particles or snowflakes. Try taking the shot
with the flash mode set to Suppressed Flash.
●
!
The flash charging time may increase if the charge remaining
in the batteries is low.
●
!
When you take a shot using the flash, you may see the video
image disappear and the screen go dark as the flash charges.
The viewfinder lamp flashes orange while the flash is
charging.
Use this mode for ordinary photography. The
flash fires automatically as required by the
shooting conditions.
AUTO
Auto Flash Mode
This mode can be selected in the
“A”, “S” still photography
modes.
✽Displaying the menus (➡P.37)
Factory default
42 43
3
Use Macro mode for close-up shots.
hFocal range: Approx. 10 cm to 80 cm (3.9 in.
to 2.6 ft.)
(Approx. 20 cm to 80 cm (0.6 ft. to 2.6 ft.) when
the flash is used)
●Digital zoom focal distance (35 mm camera
equivalent)
1M: Equivalent to approx. 38 mm-48 mm
(1.3×)
0.3M: Equivalent to approx. 38 mm-95 mm
(2.5×)
Selecting Macro mode specifies the following
camera settings:
hThe lens is fixed to the wide-angle zoom
setting and only digital zooming is available.
hThe LCD monitor is fixed to the ON setting.
hSwitching the camera off cancels Macro
mode.
●
!
When shooting in dark conditions, use a tripod to
prevent camera shake.
If you use the viewfinder to take pictures in
Macro mode, there is a discrepancy between
what you see and what the camera actually
photographs due to the difference in the
positions of the lens and the viewfinder window.
For this reason, you should always use the LCD
monitor when shooting in Macro mode.
✽Displaying the menus (➡P.37)
E
MACRO (CLOSE-UP)PHOTOGRAPHY
PHOTOGRAPHY MENU
✽Displaying the menus (➡P.37)
This mode can be selected in the
“A”, “S” still photography
modes.
Factory default
cFLASH
PHOTOGRAPHY MENU
This is a flash mode that uses a slow shutter
speed. This allows you to take pictures of people
at night that clearly show both your subjects and
the night time backdrop.
vSlow Synchro
●
!
The image may be overexposed when you shoot
bright scenes.
●
!
Because a slow shutter speed is used, a tripod
should be used to prevent camera shake.
bSuppressed Flash
Use this mode for photography using indoor
lighting, for shots taken through glass, and for
photography in venues such as theaters or at
indoor sporting events where the distance is too
great for the flash to be effective. When you use
Suppressed Flash, the Automatic White Balance
function (➡P.118) operates so that natural colors
are captured along with the ambience of the
available light.
●
!
If you are shooting in Suppressed Flash mode in dark
conditions, use a tripod to prevent camera shake.
●
!
See P.110 for information on the camera shake
warning.
44 45
3
3
The self timer lamp lights for 5 seconds and then
starts flashing. 5 seconds later the camera emits
a short beep and takes the picture.
Until the picture is taken, a countdown appears
on the LCD monitor.
Self-timer mode is automatically cancelled after
each shot.
●
!
To stop the self-timer once it has started running,
press the “BACK” button.
4
ＳＥＬＦ−ＴＩＭＥＲ
ＯＦＦ
ＯＮ
４９
１Ｍ
=
SELF-TIMER PHOTOGRAPHY
PHOTOGRAPHY MENU
✽Displaying the menus (➡P.37)
Beep
21 01
0203
When you set the self-timer to “ON”, “=” appears on
the LCD monitor.
In this mode, a timer runs for roughly 10 seconds
before the shutter is released. Use this mode for shots
such as photographs of yourself.
1Position the AF frame over your subject.
2Press the shutter button down half way to set
the focus.
3Without releasing the shutter button, press it
down fully. The self-timer then starts running.
●
!
The self-timer is automatically cancelled in the following
situations:
• When shooting ends
• When you switch to “A” or “S” mode
• When the mode switch setting is changed
• When the camera is switched off
●
!
You can also use the AF/AE lock (➡P.27).
●
!
Be careful not to stand in front of the camera when you
press the shutter button as this can cause focusing or
exposure metering errors.
This mode can be selected in the
“A” still photography mode.
Factory
default
46 47
3
Use the Brightness setting to obtain the optimum
image brightness (exposure) when the subject is
much brighter or darker than the background.
hCorrection range: –2.1 EV to +1.5 EV
(13 steps in 0.3 EV increments)
See P.118 for information on EV.
●
!
The Brightness setting is disabled in the following
situations:
iWhen the flash is used in Auto or Red-Eye
Reduction mode.
iWhen dark scenes are shot in Forced Flash mode.
hCopying of printed text (black characters on
white paper) (+1.5 EV)
hBacklit portraits (+0.6 EV to +1.5 EV)
hVery bright scenes (such as snowfields) and
highly reflective subjects (+0.9 EV)
hShots made up predominantly of sky
(+0.9 EV)
hSpotlit subjects, particularly against dark
backgrounds (–0.6 EV)
hCopying of printed text (white characters on
black paper) (–0.6 EV)
hScenes with low reflectivity, such as shots of
pine trees or dark foliage (–0.6 EV)
Guide to using + (positive) compensation
Guide to using – (negative) compensation
◆
Subjects for Which Exposure
Adjustment is Particularly Effective
◆
d
EV (EXPOSURE COMPENSATION)
PHOTOGRAPHY MENU
✽Selecting A/S(➡P.36)
✽Displaying the menus (➡P.37)
This mode can be selected in the
“S” still photography mode.
AUTO: Automatic adjustment
(Shooting to show the ambience of the
light source)
6: Shooting outdoors in fine weather
7: Shooting in shade
9: Shooting under “Daylight” fluorescent
lamps
0: Shooting under “Warm White” fluorescent
lamps
-: Shooting under “Cool White” fluorescent
lamps
8: Shooting in incandescent light
✽ The white balance setting is ignored when the flash is
used. To achieve the desired effect in your shot, set
the flash to Suppressed Flash mode (➡P.42).
Change the white balance setting when you
want to take a picture with the white balance
fixed for the surroundings and lighting when the
picture is taken.
In Auto mode, the correct white balance may not
be obtained for subjects such as close-ups of
people’s faces and shots taken under a special
light source. In such situations, select the correct
white balance for the light source. See P.118 for
information on the white balance.
✽Selecting A/S(➡P.36)
✽Displaying the menus (➡P.37)
PHOTOGRAPHY MENU
This mode can be selected in the
“S” still photography mode.
a
WHITE BALANCE (SELECTING THE LIGHT SOURCE)
Factory default
Factory default
48 49
3
During movie shooting, the lens is fixed at the
wide-angle zoom setting and only the digital
zoom can be used.
Use “a” or “b” to zoom in and out. A zooming
bar is displayed on the LCD monitor.
The focal distances and maximum zoom ratios
for the digital zoom are shown below.
hDigital zoom focal distance (35 mm camera
equivalent)
Approx. 38 mm to 95 mm
Max. zoom scale: 2.5×
●
!
You do not need to hold down the shutter button.
●
!
The focus is fixed at 80 cm (2.6 ft.) to infinity.
●
!
The white balance is fixed during shooting, but the
exposure varies automatically to suit the scene being
shot.
●
!
The image shown on the LCD monitor before you
take the shot may differ in its brightness, color, etc.
from the image shown on the monitor during movie
recording.
When you press the shutter button, the camera
starts shooting.
4
The white balance is set automatically when you
press the shutter button.
3
Approx.
40.6 min.
Approx.
12.9 min.
DPC-128 (128 MB)
Approx.
20.2 min.
Approx.
6.4 min.
DPC-64 (64 MB)
Approx.
10.1 min.
Approx.
191 sec.
DPC-32 (32 MB)
Approx.
5.0 min.
DPC-16 (16 MB)
$#
Quality mode
xD-Picture Card
Capacity
Approx.
94 sec.
TMOVIE (VIDEO)
T
MODE
12
●
!
Select Macro mode for close-up shots (➡P.43).
●
!
Depending on the available space on the xD-Picture
Card, the available shooting time per movie may be
shorter.
●
!
You cannot switch the LCD monitor off in this mode.
●
!
It may not be possible to play back your movie on
other cameras.
Set the Mode switch to “T”.
This mode allows you to shoot movies up to 20
seconds (at the #setting) or 80 seconds (at the
$setting) without sound. (See P.51 for
information on quality settings.)
hMovie format: Motion JPEG (➡P.118)
#(320 ×240 pixels)
$(160 ×120 pixels)
selectable
10 frames per second
Without sound
The available shooting time and the “œ”
message are shown on the LCD monitor.
■xD-Picture Card standard shooting time
✽The available shooting time displayed on the camera
for a new xD-Picture Card formatted in the camera.
Continued on next page...
50 51
3
Quality settings for movies
1Use “a” or “b” to change the quality setting.
2Press the “MENU/OK” button to confirm the
selection.
1Set the Mode switch to “T”.
2Press the “MENU/OK” button to display the
menu screen.
3Press “d” or “c” to select “y” QUALITY.
You can select 2 levels of quality. For better
image quality, select “#”, and for longer
photography time, select “$”.
Movie Size
#320 ×240
$160 ×120
Maximum shooting time
20 sec.
80 sec.
03
01
02
1
●
!
Once the remaining time runs out, movie recording
automatically stops and the movie is stored on the
xD-Picture Card.
During shooting, “hREC” appears on the LCD
monitor with a counter showing the remaining
time displayed in the top-right corner.
●
!
If you end shooting immediately after you start
shooting, only 1 second of movie is shot.
If you press the shutter button during shooting,
shooting ends and the movie is stored on the
xD-Picture Card.
56
TMOVIE (VIDEO)
T
MODE
0201
2
ＱＵＡＬＩＴＹＱＵＡＬＩＴＹ
Factory default
52 53
4
■Playing Back Movies
The movie automatically stops when playback ends.
Playback
Control Description
Pauses the movie during playback.
Press this button again to resume playback.
Pause/Resume
Stops playback.
✽Press “d” or “c” while movie playback is stopped to go back
to the previous file or advance to the next file respectively.
Stop
Press these during playback to skip forwards or backwards
through the movie.
Fast forward/Rewind
iEach time you press “d” or “c” when the movie is
paused, the movie advances or goes back one frame.
iHold down the button to move through the frames
quickly.
Skip playback
When paused
Rewind Forward
◆Playing back movie files ◆
iThis camera may not be able to play back movie files (10 fps) that were recorded on a camera other than FinePix A204.
iTo play back movie files on a computer, save the movie file on the xD-Picture Card to the computer’s hard disk and then
play back the saved file.
iMovie files contain large amounts of data. Depending on the performance of the computer, movies may not run
smoothly if the computer cannot process the images quickly enough.
PLAYING BACK MOVIES
w
MODE
4
Advanced
Features Playback
2
1Press “b({)” to play the movie.
2The LCD monitor shows the playback time
and a playback progress bar.
●
!
If the subject of the movie is very bright, white
streaks may appear on the image during playback.
This is normal and is not a fault.
●
!
Movies cannot be played back using multi-frame
playback. Use the “DISP” button to revert to normal
playback.
1Set the Mode switch to “w”.
2Use “d” or “c” to select the movie file.
Movies are displayed somewhat smaller than
still images.
01
02
10102
54 55
4
1Use “a” or “b” to select “FORMAT”, “ALL
FRAMES” or “FRAME”.
2Press the “MENU/OK” button to confirm the
selection.
0102
BACK
Returns to playback without erasing
any files.
FRAME
Erases only the selected file.
ALL FRAMES
Erases all unprotected files.
You should copy important files that
you do not want to be erased to your
computer or another media.
FORMAT
Erases all the files. Because
formatting also erases protected files,
check carefully before formatting a
card and copy any files that you want
to keep onto another media, such as
your hard disk.
3
Continued on next page...
p
ERASING SINGLE •ALL FRAMES/FORMATTING
PLAYBACK MENU
1Set the Mode switch to “w”.
2Press the “MENU/OK” button to view the
menu screen.
Use “d” or “c” to select “p” ERASE.
10102
2
Note that mistakenly erased images cannot be
recovered. You should copy important files that
you do not want to be erased to your computer
or another media.
56 57
4
◆To stop the procedure mid-way ◆
When you want to cancel the “Erase all frames”
procedure, press the “BACK” button.
●
!
Even if you stop the procedure immediately,
some files will be erased.
FORMAT
Pressing the “MENU/OK” button erases all the
files and initializes the xD-Picture Card.
Formatting also erases protected files.
●
!
If the “∂”, “ƒ”, “å” or
“˙” message appears, refer to
P.110, 111 before formatting the xD-Picture Card
and take the appropriate measures.
FRAME ALL FRAMES
1Use “d” or “c” to select the file to be erased.
2Press the “MENU/OK” button to erase the
currently displayed file.
To erase another image, repeat steps 1and 2.
When you have finished erasing images, press
the “BACK” button.
Pressing the “MENU/OK” button erases all the
unprotected files.
●
!
The file for which “ˆ” was displayed
cannot be erased. Remove the protection.
If the “©”
“
ø
” message appears,
press the “MENU/OK” button once more to erase
the image.
pERASING SINGLE •ALL FRAMES/FORMATTING
PLAYBACK MENU
0102
58 59
4
1Press “a” or “b” to select “UNPROTECT ALL”,
“PROTECT ALL” or “FRAME SET/RESET”.
2Press the “MENU/OK” button to confirm the
selection.
0102Protects or unprotects only the
selected file.
FRAME SET/RESET
Removes the protection from all the
files.
UNPROTECT ALL
Protects all the files.
PROTECT ALL
3
Continued on next page...
Protection is a setting that prevents images from
being accidentally erased. However, “FORMAT”
erases all images, regardless of protection
setting (➡P.57).
1Set the Mode switch to “w”.
2Press the “MENU/OK” button to view the
menu screen.
Use “d” or “c” to select “k” PROTECT.
10102
2
●
!
Multi-frame playback is an easy way to select
images to be protected (➡P.32).
kPROTECTING IMAGES FRAME/ALL
PLAYBACK MENU
60 61
4
PROTECT ALL
Press the “MENU/OK” button to protect all the
files.
Press the “MENU/OK” button to unprotect all the
files.
UNPROTECT ALL
◆
To stop the procedure mid-way
◆
If the photographed images are very large, protecting or unprotecting all the
frames may take some time.
If you want to shoot a picture or a movie during the procedure, press the “BACK”
button. To then return to protecting or unprotecting all the frames, start the
procedure on P.58 from step .
1
１００−０００９１００−０００９
ＰＲＯＴＥＣＴ ＡＬＬＰＲＯＴＥＣＴ ＡＬＬ
ＢＡＣＫＢＡＣＫ ＣＡＮＣＥＬＣＡＮＣＥＬ
FRAME SET/RESET
0102
1Press “d” or “c” to select the file to be
protected.
2Press the “MENU/OK” button to protect the
file currently displayed.
To protect another file, repeat steps 1and 2.
To finish protecting files, press the “BACK”
button.
To remove the protection, press the “MENU/OK”
button.
1 2
kPROTECTING IMAGES FRAME/ALL
PLAYBACK MENU
62 63
4
10102
2
1Set the Mode switch to “w”.
2Press the “MENU/OK” button to display the
menu screen.
Use “d” or “c” to select “i” DPOF.
iDPOF SET FRAME
PLAYBACK MENU
Continued on next page...
DPOF stands for Digital Print Order Format and refers to a format that is used for
recording printing specifications for images shot using a digital camera on media such as
an xD-Picture Card. The recorded specifications include information on which frames are
to be printed.
This section gives a detailed description of how to order your prints with the FinePix A204.
On the FinePix A204, you can specify only one print per image in the DPOF settings.
✽ Note that some printers do not support date and time imprinting or specification of the
number of prints.
✽ Note that the warnings shown below may be displayed while you are specifying the
prints.
©
ø(➡P.56)
When you erase the image, the DPOF setting for that image is deleted at the same time.
¥(➡P.66)
If you load an xD-Picture Card that contains frames specified for printing on another
camera, those print specifications are all reset and replaced by the new print specifications.
™(➡P.111)
Up to 999 frames can be specified on the same xD-Picture Card.
iHOW TO SPECIFY PRINT OPTIONS (DPOF)
PLAYBACK MENU
64 65
4
3
50102
6
1Use “d” or “c” to display the frame for which
you want to specify DPOF settings.
2Press “a” or “b” to set “YES” for the frame to
be printed and then press the “MENU/OK”
button or “c”.
To specify more DPOF settings, repeat steps 1
and 2.
●
!
DPOF settings cannot be specified for movies.
●
!
“TOTAL” shows the total number of frames for which
prints have been ordered.
When you have finished the settings, always
select “FINISH” and press the “MENU/OK”
button.
If you press the “BACK” button, no DPOF settings
are specified.
●
!
You can only specify one print per frame in the DPOF
settings. Note also that you can specify prints for up
to 999 frames on the same xD-Picture Card.
Continued on next page...
1Press “a” or “b” to select “DDATE”.
2Use “d” or “c” to select “DATE ON” or
“DATE OFF”.
The selected setting is then valid for all frames
with DPOF settings.
3
0102
4
0102
1Press “a” to select “OK”.
2Press the “MENU/OK” button.
iDPOF SET FRAME
PLAYBACK MENU
67
5
66
5Settings gADJUSTING THE MONITOR BRIGHTNESS
You can set the monitor brightness in “Q”, “w”
and “T” mode.
1Press the “MENU/OK” button to display the
menu screen.
2Press “d” or “c” to select “g” OPTION and
then press “a” or “b” to select “LCD
BRIGHTNESS”.
3Press the “MENU/OK” button.
2
0102
010302
1
●
!
To exit this procedure without changing the settings,
press the “BACK” button.
1Use “d” or “c” to adjust the LCD monitor
brightness.
2Press the “MENU/OK” button.
Pressing the “MENU/OK” button confirms the
DPOF settings.
Pressing the “BACK” button returns you to the
settings screen .
5
7
Pressing the “MENU/OK” button confirms all the
settings.
◆
DPOF settings cannot be changed.
◆
If you select a frame for which DPOF settings have
already been specified, the “¥”
message appears.
Pressing the “MENU/OK” button erases all the
DPOF settings already specified. You must then
specify the DPOF settings again.
●
!
Press the “BACK” button to leave the previous
settings unchanged.
●
!
During playback, check that the “i” icon is
displayed for the previous settings.
iDPOF SET FRAME
PLAYBACK MENU
68 69
5
■SET–UP Menu Options
Settings Display Explanation
POSTVIEW
USB MODE
POWER SAVE
DATE/TIME
ON/OFF
DSC/PC CAM
ON/OFF
SET
This option specifies whether or not an image checking screen (photography
results) is displayed after you take a shot.
The photography results are displayed for about 2 seconds and then automatically
recorded.
See P.82 for details.
If the camera is not used for approximately 30 seconds, this function temporarily
switches off the LCD monitor. See P.70 for details.
Use this option to correct the date or time. See P.15 for details.
Use this option to specify whether the LCD monitor is automatically switched ON or
OFF when the Mode switch is set to “Q”.
This setting selects the volume of the beep emitted by the camera during camera operation.
This resets all camera settings (including the photography and playback menu
settings) other than the date and time to the factory default values set at shipment.
When you press “c”, a confirmation screen appears. To proceed, press the
“MENU/OK” button again.
Select English, French or German as the language used for screen display.
Factory
default
ON
DSC
ON
—
QLCD ON/OFF ON
BEEP FLOW/HIGH/OFF LOW
RESET ALL OK —
LANGUAGE
ENGLISH/FRANCAIS/
DEUTSCH
ENGLISH
■List of settings
AAUTO
SMANUAL
LCD BRIGHTNESS (P.67)
SET–UP
QStill photography mode
—
—
LCD BRIGHTNESS (P.67)
SET–UP
TMovie mode
—
—
LCD BRIGHTNESS (P.67)
SET–UP
wPlayback mode
1Press “a” or “b” to select a menu option and
then press “d” or “c” to change the setting.
2Press the “MENU/OK” button.
You can set the SET–UP in “Q”, “w” and “T”
mode.
1Press the “MENU/OK” button to display the
menu screen.
2Press “d” or “c” to select “g” OPTION and
then press “a” or “b” to select “SET–UP”.
3Press the “MENU/OK” button.
●
!
Press “c” for “DATE/TIME” or “RESET ALL”.
2
101
0201
0203
●
!
The figure above shows the screen for still
photography.
gUSING SET–UP
71
6
70
Software needed for playing back movies, etc.
Launches the FinePixViewer
software when a camera is
connected.
Software used to read PDF-format documents on a
personal computer. This software is needed to read the
User’s Guides for FinePixViewer.
Creates a FinePix CD Album.
Used for videoconferencing (Windows only).
Allows you to display thumbnail lists of the
images stored on your PC or in the camera,
print the images individually or as an index,
display the images at full size and perform
some basic image processing.
✽ Note that the software configuration differs slightly depending on your operating system.
Connect the camera
with “DSC” selected as
the USB setting
(➡P.84).
Connect the camera
with “PC CAM”
selected as the USB
setting (➡P.87).
Allows a digital camera to be used
as USB Mass Storage (removable
disk drive, card reader).
Allows a digital camera to be
used as a PC Camera.
ImageMixer VCD
for FinePix
FinePixViewer
PictureHello
Acrobat Reader
R
QuickTime
USB PC Camera
Driver
Exif Launcher
USB Mass Storage
Driver
6 Software Installation
6.1 The Software Components
When the camera is in Sleep mode, pressing
any button on the camera will switch the LCD
monitor back on. Sleep mode offers a useful
alternative to switching the camera off because
the camera is ready to use far more quickly.
Even when the camera is asleep, you can still
release the shutter and take pictures.
●
!
Power Save/Auto Power Off does not function when
a USB connection is being used.
●
!
Operation can also be restored by pressing buttons
other than the shutter button.
●
!
To switch the camera back on, briefly switch the
camera off and then on again.
The Sleep function does not operate when the
LCD monitor is switched off, while you are
setting the quality or when the camera is in
SET–UP or Playback mode. However, if the
camera controls are not used for 2 minutes, the
camera automatically switches off.
gPOWER SAVE
SET–UP
hPower saving “ON” (default setting)
Power consumption is kept to a minimum to
prevent battery depletion. You should select the
“ON” setting when you are using alkaline
batteries.
iIf the camera is not used for approximately 30
seconds, the LCD monitor switches off temporarily
to reduce power consumption (Sleep mode).
iOnce the camera is in Sleep mode, if it is left
unused for a further 90 seconds, it is automatically
switched off.
iThe charging time for the flash increases slightly
because the flash charging power is reduced.
hPower saving “OFF”
Batteries are more likely to run flat since no
power reduction measures (sleep mode, etc.)
are used. However, this function automatically
switches the camera off if the camera is not
used for approximately 2 minutes.
Factory default
72 73
6
Launching the Installer Manually
1. Double-click the “My Computer” icon.
✽Windows XP users should click “My
Computer” in the “Start” menu.
2. Right-click “FINEPIX” (CD-ROM drive) in
the “My Computer” window and select
“Open”.
3. Double-click “SETUP” or “SETUP.exe”
in the CD-ROM window.
✽The way file names are displayed differs as
described below depending on your computer
settings.
• File extensions (3-letter suffixes indicating
the file type) may be shown or hidden. (e.g.
Setup.exe or Setup)
• Text may be shown normally or all in
uppercase (e.g. Setup or SETUP).
1. Pre-installation checking begins. If any
warning messages appear, follow the
instructions given on the screen.
✽The “Add New Hardware Wizard” may be hidden
behind the “Note” message. Check the taskbar,
move the message window and then click the
[Cancel] button.
6.2.2 From FinePixViewer installation to restart
6.2 Installation on a Windows PC
6.2.1 Load the CD-ROM into your PC
1. Switch on your PC and start up Windows.
✽If you have already switched on your PC, restart
your PC at this point.
Users of Windows 2000 or Windows XP should log in
using a system administrator account (e.g.
“Administrator”).
2. Quit all other active applications until no
applications are shown in the taskbar.
If a “----.dll file not found.” message appears during
installation, there is another application running in the
background. Forcibly shut down the application. Refer
to your Windows manuals for information on how to
forcibly shut down an application.
3. Load the enclosed CD-ROM into the CD-ROM
drive. The installer starts up automatically.
NOTE
NOTE
Do not connect the camera to your PC until
the software installation is completed.
4. The Setup screen appears. Click the
[Installing FinePixViewer] button.
✽For more information on what is installed, click the
[Read Me First] button and [Using FinePixViewer]
button.
74 75
6
3Check the installation destination folder and then
click the [Next >] button.
4The “Confirmation” screen shown may appear.
To continue with the settings, click the [Yes]
button.
2. A confirmation message appears asking
whether you want to continue with the
installation. Click the [OK] button.
3. The software version is checked. If the
window shown below appears, click the
[OK] button to uninstall the software.
4. The USB drivers are installed.
5. Install FinePixViewer.
1FinePixViewer installation begins and notes and
warnings are displayed. When you have
confirmed these, click the [Next >] button.
2The User License Agreement for this software is
displayed. Read the agreement carefully and
then, if you agree to the terms of the Agreement,
click the [Yes] button. If you click the [No] button,
the software is not installed.
6. Install QuickTime as directed by the on-
screen instructions.
✽If you have already installed QuickTime version
5.0.2 or later, this installation is not performed.
Click the [Agree] button in the “Software License
Agreement” window.
If the “Connection speed” window appears, set the
correct speed for your environment of connection and
then click the [Next] button.
✽If you do not know your connection speed, simply
click the [Next] button.
7. Install NetMeeting as directed by the on-
screen instructions.
✽If NetMeeting 3.01 or later is already installed on
your PC, this installation is not performed.
8. Install ImageMixer VCD for FinePix as
directed by the on-screen instructions.
9. Close the “Readme” window.
10
.Install WINASPI as directed by the on-screen
instructions.
11
.Install Windows Media Player as directed
by the on-screen instructions and then
restart your PC.
✽If the latest version of the software is already installed
on your PC, this installation is not performed. When
next screen appears, click the [Restart] button.
In Windows Media Component Setup window, tick
the “I have read the Privacy Statement” checkbox
and then click the [Next >] button.
When you click the [Finish] button, your PC is
restarted.
76 77
6
2. Double-click “Installer for MacOS8.6-9.x”
to launch the Installer.
3. The Installer setup screen appears. Click
the [Installing FinePixViewer] button.
✽For more information on what is installed, click the
[Read Me First] button and [Using FinePixViewer]
button.
4. A confirmation message appears asking
whether you want to continue with the
installation. Click the [OK] button.
5. The User License Agreement for this
software is displayed. Read the agreement
carefully and then, if you agree to the
terms of the Agreement, click the [Yes]
button. If you click the [No] button, the
software is not installed.
6.3 Installation on a Mac OS 8.6 to 9.2
6.3.1 Check the system software settings
■Enable File Exchange
Check whether File Exchange is active.
To use an xD-Picture Card that is supported by the
camera, the File Exchange utility supplied with Mac
OS must be running.
1. Switch on your Macintosh and start up
Mac OS 8.6 to 9.2.
Do not connect the camera to your Macintosh until the
software installation is completed.
2. Select the Extension Manager in the Control
Panel and check that the File Exchange
check box is ticked. If not, click in the box
so that an appears and then restart your
Macintosh.
NOTE
6.3.2 From FinePixViewer installation to restart
1. When you load the enclosed CD-ROM into
the CD-ROM drive, the “FinePix” window
automatically opens.
If the “FinePix” window does not open automatically,
double-click the CD-ROM icon.
NOTE
15
.Proceed with the installation as directed
by the on-screen instructions.
■To install Acrobat Reader later...
1. Open the “My Computer” window, right-click
the CD-ROM icon and select “Open” to view
the contents of the CD-ROM.
2. Double-click “ACROREAD” →“ENGLISH”
folder.
3. Double-click “ar505enu.exe”.
4. Proceed with the installation as directed by
the on-screen instructions.
12
.After you restart your PC, install DirectX as
directed by the on-screen instructions and
then restart your PC again. If the latest
version of DirectX is already installed on
your PC, this installation is not performed.
13
.After you restart your PC, the “FinePixViewer
installation completed” message appears.
Click “Using FinePixViewer” to view the
basic FinePixViewer functions.
14
.To install Acrobat Reader, click “Install
Acrobat Reader”.✽
✽You should install Adobe Acrobat Reader
software to read the FinePixViewer User’s Guide
(PDF).
If you already have the latest version installed,
this step is not required.
78 79
6
8. After you restart your Macintosh, the
“FinePixViewer installation completed”
message appears. Click “Using
FinePixViewer” to view the basic
FinePixViewer functions.
9. To install Acrobat Reader, click “Install
Acrobat Reader”.✽
✽You should install Adobe Acrobat Reader
software to read the FinePixViewer User’s Guide
(PDF).
If you already have the latest version installed,
this step is not required.
10
.Proceed with the installation as directed
by the on-screen instructions.
■To install Acrobat Reader later...
1. Double-click the “FinePix” CD-ROM to
open the CD-ROM window.
2. Double-click “FinePixViewer for Mac OS
8.6-9.x” →“Acrobat Reader” →“English”
folder.
3. Double-click “English Reader Installer”.
4. Proceed with the installation as directed by
the on-screen instructions.
6. Select the installation destination for
FinePixViewer and ImageMixer VCD for
FinePix.
1Click the [Open] button to open the installation
destination folder.
2Click the [Save] button.
7. Install QuickTime as directed by the on-
screen instructions and then restart your
Macintosh.
✽If you have already installed QuickTime version
5.0.2 or later, this installation is not performed.
If the “Connection Speed” window appears after you restart your
Macintosh, set the correct speed for your environment of
connection and then click the [Next] button.
✽If you do not know your connection speed, simply click the
[Next] button.
Click [Agree] button in the “License” window.
80 81
6
9. Select the Mac OS X startup disk as the
installation destination and click the
[Continue] button.
10
.Click the [Install (upgrade)] button.
11
.When you have completed the installation,
click the [Restart] button.
6.4 Installation on a Mac OS X
6.4.1 From FinePixViewer installation to restart
Only FinePixViewer is installed on Mac OS X.
AVI movies cannot be played back on version 10.0.4.
1. Switch your Macintosh on and start up Mac
OS X. Do not launch any other applications.
2. Load the enclosed CD-ROM into the CD-
ROM drive. The “FinePix” window opens.
If the “FinePix” window does not open automatically,
double-click the CD-ROM icon.
3. Double-click “Installer for MacOS X”.
NOTE
NOTE
4. Click the “ ” icon.
5. Enter the administrator name and password.
Then click the [OK] button.
6. Click the [Continue] button.
7. Quit any other programs that are running
and then click the [Continue] button.
8. Click [Continue] button in the “Software
License Agreement” window.
82 83
7
DC IN 3V
socket
AC power adapter
Camera
7.1 Using the optional AC Power adapter
Always use a FUJIFILM AC Power Adapter AC-3V
(➡P.102).
Use the AC power adapter to avoid losing power
at inconvenient times, such as when you are
downloading photographed images to your
computer. Using the AC power adapter also
allows you to take pictures and play back images
without worrying about depleting the batteries.
✽See P.107 for notes on using the AC power adapter.
✽Only connect or disconnect the AC power adapter
when the camera is switched off.
Connecting or disconnecting the AC power adapter
while the camera is switched on temporarily interrupts
the power supply to the camera, so that images or
movies being shot at the time are not recorded.
Failing to switch the camera off first can also result in
damage to the xD-Picture Card or malfunctions during
PC connection.
Check that the camera is switched off. Plug the
AC power adapter connector into the “DC IN 3V”
socket and then plug the AC power adapter into
the power outlet.
✽The socket-outlet shall be installed near the equipment
and shall be easily accessible.
✽The shape of the plug and socket-outlet depends on
the country of use.
Connecting the AC power adapter does not
allow you to charge the Ni-MH batteries. Use the
optional charger (➡P.102) to charge the Ni-MH
batteries.
✽Sold separately
■DSC (Mass storage device) Mode
This mode provides a simple way to read images
from an xD-Picture Card and store images on to
an xD-Picture Card (➡P.84).
The first time you connect the camera
to your computer refer to Section 6
You must install all the
software before
connecting the camera
to your computer.
■PC CAM (PC Camera) Mode
This function allows you to conduct
videoconferencing sessions between PCs
connected to the Internet (➡P.87).
✽Videoconferencing (“PictureHello”) is not
supported on Macintosh computers.
✽Connection is only possible with a FUJIFILM camera
equipped with a “PC Camera” function.
For more information on using the software,
refer to “How to use FinePixViewer” in the HELP
menu which was installed from the CD-ROM.
If the power cuts out during data transmission,
the data will not be transmitted correctly. Always
use the AC power adapter when connecting the
camera to a computer.
The “Camera Connection” section explains how
to connect the camera to your computer using
the special USB cable and describes the
functions you can use once the camera and
computer are connected.
7 Camera Connection
CD-ROM
(Software for FinePix SX)
84 85
7
■Camera Operation
iWhen the camera and computer are exchanging
data, the self timer lamp flashes and the
viewfinder lamp flashes alternately green and
orange.
i“DSC” appears on the screen.
iPower Save is disabled when the camera is
connected to a USB port.
✽Before replacing the xD-Picture Card, always
disconnect the camera from the PC using the
procedure on P.90.
✽Do not disconnect the USB cable when the camera is
communicating with the PC. See P.90 for information
on the disconnection procedure.
■PC Operation
✽ The Windows CD-ROM may also be required
during installation. In this event, switch CD-ROMs
as directed by the on-screen instructions.
iFinePixViewer automatically starts up.
Windows 98/98 SE/Me/2000 Professional
iA removable disk icon appears and you can
use your PC to transfer files to and from the
camera.
Windows Macintosh
✽Screen for
Windows 98 SE
If the above operations do not occur, you do not
have the required software programs or drivers
installed on your PC. Complete the required PC
setup procedures. Then reconnect the camera
to your PC.
(USB)socket
AC power
adapter✽
Camera
PC
USB socket
1. Load an xD-Picture Card containing
photographed images into your camera. Plug
the AC power adapter connector into the DC
IN 3V socket on the camera and then plug
the adapter itself into the main power outlet.
2. Slide the power switch to the side to turn
the camera on.
3. Set the “USB MODE” setting in the
“SET–UP” menu to “DSC” (➡P.68, 69).
4. Slide the Power switch to the side to turn
the camera off.
5. Switch your PC on.
6. Use the special USB cable to connect the
camera to your computer.
7. Switch the camera on.
Always use the prescribed procedure when
disconnecting or switching off the camera
(➡P.90).
If you are using a Windows PC, the driver settings
are specified automatically when installation is
completed. No further action is required.
✽On Windows XP and Mac OS X, you must specify the
automatic launch settings the first time you connect
the camera to your computer.
✽Take care to ensure that the special USB cable is
connected the correct way around and that the plugs
are pushed fully into the connection sockets.
7.2 Use at DSC mode
✽Sold separately
86 87
7
(USB)socket
AC power
adapter✽
Camera
Plug the AC power adapter connector into the
DC IN 3V socket on the camera and then plug
the adapter itself into the main power outlet.
1. Slide the power switch to the side to turn
the camera on.
2. Set the “USB MODE” setting in the
“SET–UP” menu to “PC CAM” (➡P.68, 69).
3. Slide the power switch to the side to turn
the camera off.
✽Select Macro mode for close-up shots (➡P.43).
Although the “E” icon is not displayed.
4. Switch your PC on.
5. Use the special USB cable to connect the
camera to your computer.
6. Switch the camera on.
Always use the prescribed procedure when
disconnecting or switching off the camera
(➡P.90).
✽Take care to ensure that the special USB cable is
connected the correct way around and that the plugs
are pushed fully into the connection sockets.
If you are using a Windows PC, the driver
settings are automatically specified when
installation ends. Just wait a few moments.
7.3 Use at PC-CAM mode
PC
USB socket
✽Sold separately
1. The “Found New Hardware” help message
appears in the bottom-right corner of your
screen. This message will close when the
settings are completed. No action is required.
✽This step is not required for subsequent connections.
2. Specify the settings in the “AutoPlay” dialog
box.
■When FinePixViewer is included in
the list of actions to perform
Select “Viewing images using FinePixViewer”
and then select the “Always do the selected
action” checkbox. (This checkbox may not be
shown in some cases.)
Click the [OK] button to launch FinePixViewer.
Windows XP ■When FinePixViewer is not included
in the list of actions to perform
Select “Take no action” and then select the “Always
do the selected action” checkbox. (This checkbox
may not be shown in some cases.)
Click the [OK] button and launch FinePixViewer
manually.
3. A new removable disk icon appears in the
“My Computer” window.
The next time you connect the camera, the removable
disk drive icon and name change to the “FinePix” icon
and name.
TIP
Proceed to “Using FinePixViewer” on
page 92.
88 89
7
If the “Digital Signature Not Found” dialog box
appears, click the [Yes] button.
The USB PC Camera Driver is installed automatically.
When the following screen appears, click the
[Continue] button.
3. FinePixViewer starts up automatically and
the live image is displayed.
If the live image does not appear, refer to “Troubleshooting”
in the FinePixViewer User’s Guide (PDF).
The Exif Launcher installed with the FinePixViewer
automatically launches FinePixViewer when you
connect the camera to your PC.
TIP
NOTE
Windows XP
Windows 2000 Professional
2. Check PC operation. The installation
procedure differs depending on the
operating system running on your PC.
✽This step is not required for subsequent
connections.
The “New Hardware Found” wizard appears. The
wizard will close when the settings are completed.
No action is required.
✽ The Windows CD-ROM may also be required
during installation. In this event, switch CD-ROMs
as directed by the on-screen instructions.
Windows 98/98 SE/Me
■Camera Operation
iWhen the camera and computer are
exchanging data, the self timer lamp flashes
and the viewfinder lamp flashes alternately
green and orange.
i“PC CAM” appears on the screen.
iPower Save is disabled when the camera is
connected to a USB port.
✽Do not disconnect the USB cable when the camera is
communicating with the PC. See P.90 for information
on the disconnection procedure.
✽If the camera is used as a PC camera, a light source
such as fluorescent tube stand can be used to
illuminate the subject and get a brighter image.
✽When the camera is connected to a computer as a
PC camera, the color tones on the LCD monitor may
change briefly.
■PC Operation
1. FinePixViewer automatically starts up and
the PictureHello window opens (Windows
only).
✽Screen for Windows 98 SE
If the above operations do not occur, you do not
have the required software programs or drivers
installed on your PC. Complete the required PC
setup procedures. Then reconnect the camera
to your PC.
90 91
7
(USB)socket
AC power
adapter✽
Camera
1. Switch the camera off.
2. Unplug the special USB cable from the
camera.
✽When you drag the icon to the Trash, “≠”
appears on the camera’s LCD monitor.
3
3. The menu option shown below appears.
Click on this option.
✽ Screen for Windows Me
4. The “Eject hardware” dialog box appears.
Click the [OK] button or the close button.
Drag the “Removable drive” icon on the desktop
to the Trash.
Macintosh ✽Sold separately
1
1. Quit all applications (FinePixViewer etc.)
that are using the camera.
2. Check that the viewfinder lamp is lit green
or that the self timer lamp is off (no data is
being exchanged with the computer).
Perform the steps shown below before you
switch the camera off. This procedure
differs depending on the operating system
software (or PC) you are using.
No PC operation is needed.
1. Right-click the removable disk icon in the
“My Computer” window and select Eject.
This step is only required in Windows Me.
Windows Me/2000 Professional/XP
Windows 98/98 SE
2. Left-click the Eject icon in the taskbar and
eject “USB Disk”.
✽Even when “Copying” is no longer displayed on the
computer, the camera and the computer may still be
exchanging data. Always check that the viewfinder
lamp is lit green or that the self timer lamp is off.
2
For a DSC connection, proceed to step .
For a PC CAMERA connection, proceed to step .
3
2
✽ Screen for Windows Me
7.4 Disconnecting the Camera
92 93
8
3. Click the [Automatic Taking] button.
Mac OS X
Mac OS 8.6-9.2
8 Using FinePixViewer
8.1 Saving Images on Your Computer and viewing images
This section gives a brief overview of how to use
FinePixViewer. Refer to these instructions while you
are using FinePixViewer.
1. Connect the camera to your computer in
DSC mode (➡P.84).
2. When you open the folders shown below
in order, the images in the camera are
displayed in the thumbnail display area.
On Windows XP, the
removable disk appears
as “FinePix” (for the
second and subsequent
connections).
NOTE
Windows
1
2
3
4
2
3
1
4
2
3
4
1
Copies multiple images
at once.
4. Check that the files are downloaded from
the camera to your computer and that a
folder with the photography date is
created. Open the folder as shown below.
To open a folder, click on the plus “ ” symbol (Windows)
or arrow “ ” (Macintosh) to the left of the folder.
OR
Indicates the folder in which FinePixViewer is
installed.
Mac OS
Windows
+
TIP
1
2
3
1
2
1
2
3
5. Double-click a still-image thumbnail to
open an image window.
Always use the prescribed procedure when
disconnecting or switching off the camera
(➡P.90).
For more information on using the software,
refer to “How to use FinePixViewer” in the HELP
menu which was installed from the CD-ROM.
8.2 Making a FinePix CD Album
For using “ImageMixer VCD for FinePix” to create
CD albums and video CDs.
hTo create CD-Rs or video CDs, you will need a
CD-R drive.
hRefer to the “ImageMixer VCD for FinePix” help
file for more detailed information.
hFor inquiries regarding “ImageMixer VCD for
FinePix”
PIXELA User Support Center
PIXELA Home Page: http://www.ImageMixer.com/
North America (Los Angels) Telephone: +1-213-341-0163
Europe (U.K.) Telephone: +44-1489-564-764
Asia (Philippines) Telephone: +63-2-438-0090
Japan (Osaka) Telephone: +81-72-224-0181
94 95
8
To use the FinePix Internet services, users must
first register.
✽Follow the steps below to register. Users can be
registered for free.
1. Launch FinePixViewer.
2. Click the [Register Now] button.
3. The “User’s Registration for Internet
Services” dialog box opens. As shown at
right, select [Register Here], then select
the country or region where you are living
and click the [OK] button.
✽If you are not already connected to the Internet,
connect now (A dial-up dialog box may be
displayed).
✽If you have completed the user registration, select
“Already Registered” (E.g. When you want to re-
install FinePixViewer after completing user
registration). 4. When the browser starts up, proceed as
directed by the on-screen instructions.
✽If the country or area where you are living does
not appear in the pull-down list, select “OTHERS”.
8.3 Using the FinePix Internet Service
Mac OS X users should refer to P.96.
Using FinePixViewer also allows you to access the
FinePix Internet Service via the Internet.
✽A working Internet connection is required not only for
FinePix Internet Service, but also online FAQ
(FinePixViewer frequently asked and responses) and
latest updates.
✽A FinePix Internet Service fees do not include your
Internet service provider (ISP) connection fees or any
phone charges incurred in dialing your ISP’s access
point.
NOTE
First-time users
To the user registration
window
Registered users
The Internet menu is
updated.
■For Windows and Mac OS 8.6 to 9.2
Your user ID and password are very important. Make
sure you do not forget them.
NOTE
On FinePixViewer,sellct “QuickStart Guide/Online
FAQ” from “Help” menu, then click “FinePixViewer
Q&A”. You may obtain an answer to your question
via internet.
8.3.1 Using FAQ
8.3.2 User Registration
96 97
8
3. Select “User’s registration” and click the
[OK] button.
✽If you are not already connected to the Internet,
connect now. (A dial-up dialog box may be
displayed.)
✽Only select “Menu Acquisition” if you have already
completed the user registration process and you
have re-installed “FinePixViewer”, etc.
4. The User’s Registration
dialog box opens.
Select the country or
area where you are
living and click the
[OK] button.
✽The actual user registration page may differ slightly
in appearance from the sample shown here.
✽If the country or area where you are living does
not appear in the pull-down list, select “OTHERS”.
5. When the browser starts up, proceed as
directed by the on-screen instructions.
6. Enter the required information in the user
registration page.
1Enter the name of your choice (nickname, etc.).
2Enter a password of your choice using letters
and/or numbers. Then enter the password again
for confirmation.
3Enter your name.
4Enter your E-mail address.
5Enter the remaining required information.
✽After you register, a confirmation E-mail message
is sent to you. Be sure to enter a valid E-mail
address at which you can receive the message.
✽The actual user registration page may differ slightly
in appearance from the sample shown here.
7. When you have entered all the required
information, click the [Register] button at
the bottom of the page.
Once you complete the registration, a confirmation
E-mail is sent. Wait a few moments until the
message is sent.
1
2
3
4
5. Enter the required information in the user
registration page.
1Enter the name of your choice (nickname, etc.).
2Enter a password of your choice using letters
and/or numbers. Then enter the password again
for confirmation.
3Enter your name.
4Enter your E-mail address.
5Enter the remaining required information.
✽After you register, a confirmation E-mail message
is sent to you. Be sure to enter a valid E-mail
address at which you can receive the message.
✽The actual user registration page may differ
slightly in appearance from the sample shown
here.
6. When you have entered all the required
information, click the [Registration] button
at the bottom of the page.
Once you complete the registration, a confirmation
E-mail is sent. Wait a few moments until the
message is sent.
■For Mac OS X
To use the FinePix Internet services, users must
first register.
✽Follow the steps below to register. Users can be
registered for free.
1. Double-click the “FinePixViewer” icon in
the installed folder.
2. Click the [User’s Registration] button. The
“Operation Selection” dialog box appears.
1
2
3
4
<User’s Registration button>
98 99
8
8.5 Uninstalling the Software
Only perform this operation when you no longer
require the installed software or when the software
was not installed correctly.
1. Switch on your PC.
2. Disconnect the camera (➡P.90, 91).
3. Quit all currently running applications.
4. Close all files.
5. Open the “My Computer” window, open
the “Control Panel”, and double-click
“Add/Remove Programs”.
6. The “Add/Remove Programs Properties”
window appears. Select the software to be
uninstalled (FinePixViewer or the driver)
and then click the [Add/Remove] button.
Windows
<To remove the driver software>
<To remove FinePixViewer>
7. When the confirmation message appears,
click the [OK] button. Check your selection
carefully since the process cannot be
cancelled once you click [OK].
8. Automatic uninstallation begins.
When uninstallation ends, click the [OK]
button.
8.4 Mastering FinePixViewer
For more information on FinePixViewer functions
not fully explained in this manual, refer to “How to
Use FinePixViewer” in the Help menu for details.
■To read “How to Use FinePixViewer”...
You must install Adobe Acrobat Reader. See P.79 for
information on installing Acrobat Reader.
■What is explained in “How to Use
FinePixViewer”...
“How to Use FinePixViewer” covers a range of topics,
including batch processing and ordering prints.
■Example: Looking up slide shows
1. Click “How to Use FinePixViewer” in the
FinePixViewer Help menu.
2. Search for relevant articles by clicking the
corresponding items in the Help
“Bookmarks” or “Contents”. Here, click
“Viewing Slide Shows”.
Contents
Bookmarks
3. The “Viewing Slide Shows” information is
displayed. Press the “←” key to view the
previous page or the “→” key to view the
next page.
✽For more information on using Acrobat Reader,
refer to the Acrobat Reader “Help” menu.
101100
System Expansion Options
FinePix A204
Digital Camera
(USB)
(PC card slot)Personal Computer
(commercially available)
Digital Photo Printer
CX-400
(USB)
(USB)
PC Card Adapter
xD-Picture Card
Image Memory
Card Reader
TV monitor
(commercially available)
eBy using the FinePix A204 together with other optional FUJIFILM products, your system can be
expanded to fill a wide range of uses.
Only perform this operation when you no longer require
the installed software or when the software was not
installed correctly.
■Uninstalling Mass Storage Driver and
PC Camera Driver
1. Check that the camera is not connected to
your Macintosh.
2. Drag all the files that begin with
“USB04CB...” to the Trash.
3. Restart your Macintosh.
4. Select “Empty Trash” in the “Special” menu.
■Uninstalling Exif Launcher,
FinePixViewer and DP Editor
1. After you have quit Exif Launcher in “Exif
Launcher Settings” in the FinePixViewer
“Settings” menu, move the Exif Launcher
file from the “Startup Items” folder in the
System folder to the Trash. Then select
“Empty Trash” in the “Special” menu.
2. After you have exited FinePixViewer and
DP Editor and then drag the installed
Mac OS 8.6-9.2
NOTE
Macintosh FinePixViewer folder to the Trash. Then
click “Empty Trash” in the “Special” menu.
■Uninstalling FinePixViewer
Quit FinePixViewer and DP Editor. Then drag
the installed FinePixViewer folder to the Trash
and select “Empty Trash” in the “Special”
menu.
Mac OS X
102 103
hDPC-R1 Image Memory Card Reader
The DPC-R1 provides a quick and easy way to transfer images back and forth
between your PC and an image memory card (xD-Picture Card and SmartMedia).
The DPC-R1 uses the USB interface for high-speed file transfer.
iCompatible with Windows 98/98 SE, Windows Me, Windows 2000 Professional,
Windows XP or iMac, Mac OS 8.6 to 9.2.2, Mac OS X (10.1.2 to 10.1.5) and
models that support USB as standard.
iCompatible with SmartMedia of 3.3V, 4MB to 128MB.
●SC-FX26
This is a special case made of polyester that protects the camera against soil, dust
and minor impacts when it is being carried.
hDPC-AD PC Card Adapter
The PC Card Adapter allows the xD-Picture Card and SmartMedia to be used as
a PC Card Standard ATA-compliant (PCMCIA 2.1) PC card (Type II ).
iCompatible with SmartMedia of 3.3V, 2MB to 128MB.
hxD-Picture Card
These are separately available xD-Picture Cards.
Use the following xD-Picture Card:
DPC-16 (16MB)/DPC-32 (32MB)/DPC-64 (64MB)/DPC-128 (128MB)
●AC Power Adapter AC-3V
Use the AC power adapter when you want to take pictures or play back images
for long periods or when the camera is connected to a computer.
✽
The shape of the AC power adapter, the plug and socket outlet depend on the country.
●FUJIFILM Rechargeable Battery 2HR-3UF
The 2HR-3UF includes two (2) high-capacity AA-size Nickel Metal Hydride batteries.
●FUJIFILM Battery charger with Battery BK-NH (with Euro type or UK type plug)
The BK-NH includes the quick battery charger BCH-NH and 2 Ni-MH batteries.
The BCH-NH can charge 2 Ni-MH batteries in approximately 120 minutes.
Up to 4 Ni-MH batteries can be charged simultaneously.
Accessories Guide
eThe optional accessories (sold separately) can make taking pictures with the FinePix A204 even
easier. For information on how to attach and use the accessories, refer to the instructions provided
with the accessory used.
Visit the FUJIFILM web site for the latest information on camera accessories.
http://home.fujifilm.com/products/digital/index.html
104 105
hAA-size alkaline, Ni-MH (nickel-metal hydride) can be
used with this camera.
Do not use AA-size manganese, lithium or nickel-
cadmium (Ni-Cd) batteries in your FinePix camera
because the heat generated by the batteries could
damage the camera or cause malfunctions.
hThe operating lives of alkaline batteries vary between
brands and the life of batteries you purchase may be
shorter than the alkaline batteries provided with the
camera.
hDo not store batteries in very warm or moist
locations.
hKeep the batteries out of reach of babies and small
children.
h
When loading the batteries into the camera, ensure that
the battery polarity (
+
and
_
) is as indicated on the
camera.
hDo not use new batteries together with used
batteries. In the case of rechargeable batteries, do
not use charged and discharged batteries together.
Do not use batteries of different types or brands
together.
hIf you do not intend to use the camera for a long
period of time, remove the batteries from the camera.
(Note that if the camera is left with the batteries
removed, the time and date settings are cleared.)
hThe batteries may feel warm immediately after being
used. Before removing the batteries, switch the
camera off and wait until the batteries cool down.
h
When replacing the batteries, always fit 2 new batteries.
Here, “new batteries” refers to either recently purchased
unused alkaline batteries, or Ni-MH (nickel metal
hydride) batteries that have recently been fully
recharged together.
h
In cold locations (at temperatures of +10°C/+50°F or
below), battery performance deteriorates and the time
for which they can be used shortens markedly. This is
particularly true of alkaline batteries. In cold conditions,
put the batteries in your pocket or a similar place to
warm them before loading them into the camera. If you
use a body warmer to warm the batteries, ensure that
they are not in direct contact with the warmer.
Applicable Batteries
Notes on the Power Supply
Incorrect use of the batteries could cause them to leak,
become hot, ignite or burst. Always observe the
precautions given below.
hDo not heat the batteries or throw them into a fire.
hDo not carry or store batteries with metal objects
such as necklaces or hairpins that could come into
contact with the metal positive +and negative _
poles of the batteries.
hDo not expose the batteries to fresh or sea water,
and take particular care to keep the terminals dry.
hDo not attempt to deform, disassemble or modify the
batteries.
hDo not attempt to peel off or cut the batteries casing.
hDo not drop, strike or otherwise subject the batteries
to strong impacts.
hDo not use batteries that are leaking, deformed,
discolored or exhibit any other obvious abnormality.
Notes on the Batteries
Notes on Using Your Camera Correctly
■ Places to Avoid
Do not store or use the camera in the following types of
locations:
hIn the rain or in very humid, dirty or dusty places.
hIn direct sunlight or in places subject to extreme
temperature rises, such as in a closed car in summer.
hExtremely cold places.
hPlaces subject to strong vibration.
hPlaces affected by smoke or steam.
hPlaces subject to strong magnetic fields (such as near
motors, transformers or magnets).
hIn contact with chemicals such as pesticides or next to
rubber or vinyl products for long periods of time.
■ Notes on Immersion in Water or Sand
The FinePix A204 is particularly adversely affected by
water and sand. When you are at the beach or close to
water, ensure that the camera is not exposed to water or
sand. Take care not to place the camera on a wet surface.
Water or sand inside the camera can cause faults that may
be irreparable.
■ Notes on Condensation
If the camera is carried suddenly from a cold location into a
warm place, water droplets (condensation) may form on
the inside of the camera or on the lens. When this occurs,
switch the camera off and wait an hour before using the
camera. Condensation may also form on the xD-Picture
card. In this event, remove the xD-Picture Card and wait a
short time before using it again.
■ When the Camera is Unused for Long Periods
If you do not intend to use the camera for a long period of
time, remove the batteries and the xD-Picture Card before
storing the camera.
■ Cleaning Your Camera
hUse a blower brush to remove dust from the lens, LCD
monitor screen or viewfinder as these surfaces and then
wipe lightly with a soft, dry cloth. If any soil remains, apply
a small amount of lens cleaning liquid to a piece of
FUJIFILM lens cleaning paper and wipe gently.
hDo not scratch hard objects against the lens, LCD
monitor screen or viewfinder as these surfaces are easily
damaged.
hClean the body of the camera with a soft, dry cloth. Do
not use volatile substances such as thinners, benzine or
insecticide, as these may react with camera body and
cause deformation or remove the coating.
■ Using the Camera Overseas
When travelling overseas, do not place your camera in the
check-in baggage. Baggage handling at airports may
subject baggage to violent shocks, and the camera may be
damaged internally even when no external damage is
visible.
eBe sure to read this information in conjunction with “Safety Notes” (➡P.119), to ensure that you use
your camera correctly.
106 107
Use only the AC-3V AC Power Adapter (sold
separately) with your FinePix A204 Digital Camera. The
use of other AC power adapters may result in damage
to your camera.
hThis AC power adapter is designed exclusively for
indoor use.
hPlug the connection cord plug securely into the DC
input terminal of the FUJIFILM Digital camera.
hTurn off the power switch of the FUJIFILM Digital
camera before disconnecting the connection cord
from the FUJIFILM Digital camera’s DC input
terminal. To disconnect, take hold of the plug and pull
it out (do not disconnect it by pulling on the cord).
hDo not use this AC power adapter with any device
except the specified device.
hDuring use, this AC power adapter will become hot to
touch, but this is normal.
hDo not disassemble the AC power adapter. Doing so
could be dangerous.
hDo not use this device in a place with high
temperature and high humidity.
hDo not drop or subject this device to strong shocks.
hThis device may emit a humming noise, but this is
normal.
hIf used near a radio, this device may cause static, so
play the radio in a distant place.
AC Power Adapter
If any liquid at all leaks from the batteries, wipe the
battery compartment thoroughly and then load new
batteries.
If any battery fluid comes into contact with your
hands or clothing, flush the area thoroughly with
water. Note that battery fluid can cause loss of
eyesight if it gets into your eyes. If this occurs, do not
rub your eyes. Flush the fluid out with clean water
and contact your physician for treatment.
■Disposing of Batteries
When disposing of batteries, do so in accordance with
your local waste disposal regulations.
■Notes on Small Rechargeable Batteries (Ni-
MH batteries)
hAlways use the special battery charger to charge AA-
size Ni-MH batteries. Charge the batteries as
described in the instructions provided with the battery
charger.
hDo not use the battery charger to charge batteries
other than those specified for use with the charger.
hNote that the batteries may feel warm immediately
after being charged.
hNi-MH batteries are not charged at shipment. Be sure
to charge the batteries before using them.
hThe camera mechanism is such that it draws a
minute amount of current even when the camera is
switched off. Take particular care not to leave Ni-MH
batteries in the camera for a long period of time as
they can become excessively discharged and may no
longer be usable even when charged.
hNi-MH batteries self-discharge even when not used.
Always charge Ni-MH batteries before using them. If
the time for which a battery provides power shortens
markedly when it has been correctly charged, this
indicates that the battery has reached the end of its
effective life and should be replaced.
hSoil (fingerprints, etc) on the terminals of Ni-MH
batteries can greatly reduce the number of available
shots. When this occurs, clean the terminals carefully
with a soft dry cloth. Then use up the remaining
charge in the batteries and recharge them.
hNewly purchased batteries or batteries that have
been left unused for an extended period may not be
fully charged. (This is indicated by the immediate
display of the battery low warning or a low number of
available shots.) This is a normal characteristic of the
batteries and does not indicate a fault. Repeatedly
charging and using the batteries 3 or 4 times will
restore them to a normal condition.
hIf you repeatedly charge a Ni-MH batteries before it is
fully discharged, it will suffer from the “memory
effect”✽, causing the battery low warning to appear
while there is still ample charge remaining in the
battery. To restore the batteries to their normal
condition, use up all the charge in the batteries before
recharging them.
Notes on the Power Supply
h
Soil (such as fingerprints) on the battery terminals can
markedly reduce the number of available shots.
Carefully wipe the battery terminals clean with a soft dry
cloth before loading the batteries.
✽Memory effect: A phenomenon affecting the battery
characteristics such that the apparent
battery capacity decreases.
108 109
when images are being played back. These actions
could result in damage to the xD-Picture Card.
hThe use of xD-Picture Cards is recommended with
the FinePix A204.
The camera quality cannot be guaranteed when
cards other than those manufactured by FUJIFILM
are used.
hThe xD-Picture Card may feel warm when it is
removed from the camera after extended periods of
picture taking or image viewing. This is normal and
does not indicate a fault.
hDo not affix labels to the xD-Picture Card.
This could result in the label peeling off and causing
a fault when the card is inserted or removed.
■Notes on Using xD-Picture Card with a PC
hIf you intend to take photos using an xD-Picture Card
that has been used on a PC, format the xD-Picture
Card on your camera.
hWhen you format an xD-Picture Card in the camera
and then shoot and record images, a directory
(folder) is automatically created. Image data is then
recorded in this directory.
hDo not change or delete the directory (folder) names
or file names on the xD-Picture Card from your PC as
this will make it impossible to use the xD-Picture
Card in your camera.
hAlways use the camera to erase image data on an
xD-Picture Card.
hTo edit image data, copy the image data to the PC’s
hard disk and then edit the copied data.
hDo not copy files other than those that will be used by
the camera.
■Specifications
Type
Image memory card for digital cameras
(xD-Picture Card)
Memory type NAND-type flash memory
Conditions for use Temperature:
0°C to +40°C (+32°F to +104°F)
Humidity:
80% max. (no condensation)
Dimensions 25 mm ×20 mm ×2.2 mm
(0.98 in. ×0.79 in. ×0.09 in.) (W ×H ×D)
■Image Memory Card
hThis Image Memory Card is a new image recording
media (xD-Picture Card) developed for digital
cameras. The Image Memory Card consists of a
semiconductor memory (NAND-type flash memory)
to record digital image data.
The recording process is electrically performed and
enables erasure of existing image data as well as re-
recording of new image data.
hWhen using a new Memory Card, or a Memory Card
that has been initialized by a PC, be sure to initialize
(format/initialize) the card with your digital camera
before using it.
■Protecting Your Data
hData may be lost or destroyed in the following
situations. Please note that FUJIFILM assumes no
responsibility for data that is lost or destroyed.
1. Removal of the memory card or turning the power
off while the memory card is being accessed (i.e.,
during record, erase, initialization, and playback
operations).
2. Improper handling and use of the memory card by
the user or third party.
hWe recommend saving your important data to
another media (i.e., MO disk, CD-R, hard disk, etc.).
■Notes on Handling xD-Picture Card
hKeep xD-Picture Cards out of the reach of small
children. When storing xD-Picture Cards, ensure that
they are kept in a location out of the reach of small
children to prevent a card being accidentally
swallowed. An xD-Picture Card could cause suffocation
if accidentally swallowed. If a child swallows an xD-
Picture Card, seek medical advice immediately.
hMake sure that the memory card is straight when you
insert into the camera etc.
hThe memory card is a precision electronic instrument.
Do not apply pressure or shock, and avoid bending it.
hDo not use the memory card in a hot, humid, or
corrosive environment.
hIf the contact area on the card is soiled (dust,
fingerprints, etc.), wipe it clean with a soft, dry cloth.
hClean the memory card with a soft dry piece of cloth
when dirty.
hWhen you carry or store it, always keep the card in
the anti-static case provided. Use a storage case if
available.
hThe memory card can be used reliably for a long
period of time, but will eventually lose its ability to
store and play back image data. At this point, replace
with a new memory card.
hNever remove the xD-Picture Card or switch the
camera off during data recording, during data erasing
(xD-Picture Card formatting) or during frame advance
Notes on the xD-Picture Card
110 111
iThe data could not be recorded due to an xD-
Picture Card error or a connection error
between the xD-Picture Card and camera.
iThe photographed image cannot be recorded
as it is too large to fit in the available space on
the xD-Picture Card.
iRe-insert the xD-Picture Card or switch the
camera off and then on again.
iUse a new xD-Picture Card.
Warning Displayed Explanation Remedy
The frame number has reached 999–9999. Take the shot using a formatted xD-Picture Card.
！ＲＥＡＤ ＥＲＲＯＲ
i
An attempt was made to playback a frame not
recorded on this camera.
iThe xD-Picture Card contact area is soiled.
iCamera fault.
iYou attempted to play back a movie file that
was not recorded on this camera.
iImages cannot be played back.
iWipe the contact surface on the xD-Picture
Card thoroughly with a soft, dry cloth. In some
cases, you may have to format the xD-Picture
Card.
iContact your FUJIFILM dealer.
iPlay back the movie on a computer or on the
camera on which it was recorded.
A protected file was encountered. Protected files cannot be erased. Remove the
protection.
Prints were specified for more than 1000 frames
in the DPOF frame settings.
The maximum number of frames for which
prints can be specified on the same xD-Picture
Card is 999.
Copy the images for which you want to order
prints onto another xD-Picture Card and then
specify the DPOF settings.
Warning Displays eThe table below lists the warnings that are displayed on the LCD monitor
（赤
点
（赤
点
(Lit red)
(Blinking red)
The batteries in the camera are fully depleted or
very low on charge.
Replace the batteries or have new batteries
ready.
No xD-Picture Card is loaded. Load an xD-Picture Card in the correct direction.
！ＣＡＲＤ ＥＲＲＯＲ
iThe xD-Picture Card contact area is soiled.
iThe xD-Picture Card is damaged.
i
The xD-Picture Card format is incorrect.
iCamera fault.
iWipe the contact area on the xD-Picture Card
with a soft dry cloth. It may be necessary to
format the xD-Picture Card. If the error message
is still displayed, replace the xD-Picture Card.
iContact your FUJIFILM dealer.
The xD-Picture Card is fully recorded. Erase some images or use an xD-Picture Card
that has ample free space.
Warning Displayed Explanation Remedy
iThe xD-Picture Card is not formatted.
iThe xD-Picture Card contact area is soiled.
iCamera fault.
iFormat the xD-Picture Card.
iWipe the contact area on the xD-Picture Card
with a soft dry cloth. It may be necessary to
format the xD-Picture Card. If the error message
is still displayed, replace the xD-Picture Card.
iContact your FUJIFILM dealer.
There is a strong likelihood of camera shake
because the shutter speed is slow.
Use flash photography. However, a tripod
should be used for some scenes and modes.
The AF (auto focus) cannot work effectively. iIf the image is too dark, take the picture at a
distance of around 2 m (6.6 ft.) from the subject.
iUse AF lock to take the picture.
Outside the AE continuous range. The shot can be taken, but the exposure will not
be correct.
\
112 113
Troubleshooting eIf you think the camera is faulty, check the following once more.
Troubleshooting Possible causes Solutions
No power. iThe batteries are exhausted.
iThe AC power adapter plug has come out of
the power outlet.
iThe batteries are loaded the wrong way round.
iLoad new batteries.
iPlug the adapter back in.
iLoad the batteries in the correct direction.
Power cuts out during
operation.
The batteries are exhausted. Load new batteries.
Batteries runs out quickly. iCamera is being used in extremely cold
conditions.
iThe terminals are soiled.
iThe batteries have reached the end of their
operating lives.
iPut the batteries in your pocket or another
warm place to heat them and then load them
into the camera just before you take a picture.
iWipe the battery terminals with a clean, dry
cloth.
iLoad new batteries.
No photograph is taken
when the shutter button is
pressed.
iNo xD-Picture Card is loaded.
iThe xD-Picture Card is fully recorded.
iThe xD-Picture Card is not formatted.
iThe xD-Picture Card contact area is soiled.
iThe xD-Picture Card is damaged.
iThe Power Save function has switched the
camera off.
iThe batteries are exhausted.
iLoad an xD-Picture Card.
iLoad a new xD-Picture Card or erase some
unwanted frames.
iFormat the xD-Picture Card.
iWipe the xD-Picture Card contact area with
a clean dry cloth.
iLoad a new xD-Picture Card.
iSwitch the camera on.
iLoad new batteries.
Camera malfunction or fault. iSwitch the camera on again, taking care not to
touch the lens.
iSwitch the camera off and on again.
The lens cover is not open. Open the lens cover.
Warning Displayed Explanation Remedy
Warning Displays
114 115
Troubleshooting Possible causes Solutions
Frame erase does not
erase the frame. iSome frames may be protected. iRemove the protection.
The ERASE ALL function
does not erase all the frames.
Can’t format the xD-
Picture Card.
The xD-Picture Card contact area is soiled. Wipe the xD-Picture Card contact area with a
clean dry cloth.
When the camera is
connected to a personal
computer (PC), the shot
image appears on the
camera’s LCD monitor.
iThe USB cable is not properly connected to
the computer or camera.
iThe PC is not switched on.
iSet up the camera and the USB cable
correctly.
iSwitch the PC on.
The camera no longer
works correctly.
The camera has suffered an unforeseen
problem.
Briefly remove the batteries or disconnect the
AC power adapter. Then reload the batteries
or reconnect the AC power adapter and try
again.
Nothing happens when I
use the Mode switch.
iCamera malfunction.
iThe batteries are exhausted.
iBriefly remove the batteries or disconnect
the AC power adapter. Then reload the
batteries or reconnect the AC power adapter
and try again.
iReplace the batteries.
Troubleshooting eIf you think the camera is faulty, check the following once more.
Troubleshooting Possible causes Solutions
Can’t use the flash to take
pictures.
iThe shutter button was pressed while the
flash was charging.
iThe batteries are exhausted.
iThe Suppressed Flash mode is selected.
iWait until charging is completed before
pressing the shutter button.
iLoad new batteries.
iSet the flash mode to Auto, Red-eye
Reduction or Forced Flash (The flash cannot
be used in some modes).
The photographed image
is dark even though I used
the flash.
iThe subject is too far away.
iYour finger was covering the flash/flash
control sensor.
iMove to within the effective flash range
before taking the shot.
iHold the camera correctly.
The image is blurred. iThe lens is dirty.
iYou photographed scenery with Macro mode
selected.
iYou took a close-up shot without selecting
Macro mode.
iYou are shooting a subject that is not suited
to autofocusing.
iClean the lens.
iCancel Macro mode.
iSelect Macro mode.
iUse AF/AE lock to take the shot.
The playback image is
faded when I used the
flash to take a picture.
iThere is dust on the flash control sensor. iUse an applicator such as a cotton swab to
clean the flash control sensor.
There is speckling on the
image.
The shot was taken with a slow shutter speed
(long exposure) in a high-temperature
environment.
This is a characteristic of CCDs and does not
indicate a camera fault.
116 117
Input/Output Terminals
Power Supply and Others
hDC IN 3V (Power input) socket
Special AC Power Adapter AC-3V
h](USB) socket
USB (1) for image data output with a personal computer
hPower supply
Use one of the following:
i2AA-size alkaline batteries
i
2AA-size Ni-MH (nickel metal hydride) batteries (sold separately)
iAC Power Adapter AC-3V (sold separately)
hNo. of available shots using battery (battery life)
50%. Note that these figures may vary depending on the
ambient temperature and the amount of charge in the
battery. The number of available shots or available
shooting time will be lower in cold conditions.
hConditions for use
Temperature: 0°C to +40°C (+32°F to +104°F); 80%
humidity or less (no condensation)
hCamera dimensions (W ×× H×× D)
100.4 mm ✕65 mm ✕51.7 mm/4.0 in. ✕2.6 in. ✕2.0 in.
(not including accessories and attachments)
hCamera mass (weight)
Approx. 185 g/ 6.5 oz (not including, batteries and xD-Picture
Card)
hMass (weight) for photography
Approx. 240 g/ 8.5 oz (including batteries and xD-Picture Card)
hAccessories
See P.7
hOptional Accessories
See P.102, 103
hFlash (Auto flash using flash control sensor)
Effective range: Wide-angle Approx. 0.2 m – 3.0 m (0.6 ft. – 9.8 ft.)
: Telephoto Approx. 0.8 m – 3.0 m (2.6 ft. – 9.8 ft.)
Flash modes: Auto, Red-Eye Reduction,
Forced Flash, Suppressed Flash, Slow Synchro
hLCD monitor
1.5-inches, 55,000-pixels D-TFD
hSelf-Timer
10 sec. timer clock
✽
These specifications are subject to change without notice.
FUJIFILM shall not be held liable for damages resulting
from errors in this Owner’s Manual.
✽
The LCD monitor on your digital camera is manufactured
using advanced high-precision technology. Even so, small
bright points and anomalous colors (particularly around
text) may appear on the monitor. These are normal display
characteristics and do not indicate a fault with the monitor.
This phenomenon will not appear on the recorded image.
✽ The operation error may be caused in a digital camera by
the strong radio interference (i. e. electric fields, static
electricity, line noise, etc.).
Specifications
hModel
Digital camera FinePix A204
hNumber of effective pixels
2.0 million
hCCD Sensor
1/2.7-inch square pixel CCD
Total number of pixels: Approx. 2.11 million
hImage quality
1600 ×1200 pixels (1.92 million pixels)/1280 ×960 pixels/
640 ×480 pixels
hFile format
Still image: JPEG (Exif Ver. 2.2), DPOF-compatible
Movie : AVI format, motion JPEG
✽Design rule for Camera File system compliant
hViewfinder
Real image optical; Frame coverage: 80%
hLens
Fujinon optical 3×zoom lens
hAperture
F3.5/F8.7 (automatically selected)
hStorage media
xD-Picture Card (16MB to 128MB)
hFocus distance
f = 6 mm-18 mm
(equivalent to 38 mm-114 mm on a 35 mm camera)
hExposure control
64 zones TTL metering, Program AE
(exposure compensation available in Manual mode)
hSensitivity
Equivalent to ISO 100
hWhite balance
Auto (7 positions selectable in Manual mode)
hFocal range
Normal:Approx. 80 cm (2.6 ft.) to infinity
Macro: Approx. 10 cm (3.9 in.) to 80 cm (2.6 ft.)
hShutter speeds
Variable-speed, 1/2 to 1/ 1000 sec.
(combined with mechanical shutter)
System
hStandard number of available shots/recording time per xD-Picture Card
DPC-16 (16 MB)
DPC-32 (32 MB)
DPC-64 (64 MB)
DPC-128 (128 MB)
Quality mode
Image Data Size
2M •F2M
•N
Approx. 620 KB Approx. 390 KB
25 39
50 79
101
204
159
319
Approx. 320 KB
49
99
198
398
Approx. 130 KB
122
247
497
997
1M 0.3M
—
Approx. 94 sec.
Approx. 191 sec.
Approx. 6.4 min.
Approx. 12.9 min.
#
—
Number of recorded pixels 1600 ×1200 1280 ×960 640 ×480 320 ×240 160 ×120
Approx. 5.0 min.
Approx. 10.1 min.
Approx. 20.2 min.
Approx. 40.6 min.
$
With LCD monitor
OFF
With LCD monitor
ON
Battery type
Ni-MH batteries
HR-3UF 1700 mAh
Alkaline batteries
Approx. 250 frames✽
Approx. 150 frames
Approx. 400 frames✽
Approx. 250 frames
(Condition: Power saving mode ON, with fully charged battery (Ni-MH))
This indicates the number of available frames shot
consecutively at room temperature with a flash use rate of
118 119
When a fault arises, switch the camera
off and then remove the batteries and
disconnect the AC power adapter.
Continued use of the camera when it is
emitting smoke, is emitting any unusual
odor, or is in any other abnormal state can
cause a fire or electric shock.
hContact your FUJIFILM dealer.
Do not allow water or foreign objects to
enter the camera.
If water or foreign objects get inside the
camera, switch the camera off, remove the
battery and disconnect and unplug the AC
power adapter.
Continued use of the camera can cause a
fire or electric shock.
hContact your FUJIFILM dealer.
Do not place the camera on an unstable
surface.
This can cause the camera to fall or tip over
and cause injury.
Do not use the camera in the bathroom
or shower.
This can cause a fire or electric shock.
hTo ensure that you use your FinePix A204 camera
correctly, read these Safety Notes and your Owner’s
Manual carefully beforehand.
hAfter reading these Safety Notes, store them in a safe
place.
About the Icons
The icons shown below are used in this document to
indicate the severity of the injury or damage that can result
if the information indicated by the icon is ignored and the
product is used incorrectly as a result.
WARNING
This icon indicates that death or
serious injury can result if the
information is ignored.
CAUTION
This icon indicates that personal
injury or material damage can
result if the information is ignored.
The icons shown below are used to indicate the nature of
the information which is to be observed.
Triangular icons notify the user of information
requiring attention (“Important”).
Circular icons with a diagonal bar notify the user
that the action indicated is prohibited
(“Prohibited”).
Filled circles with an exclamation mark notify the
user of an action that must be performed
(“Required”).
Safety Notes
WARNING
Unplug from
power socket.
Do not use in the
bathroom or shower.
Explanation of Terms
DPOF: Digital Print Order Format
DPOF is a format used for recording information on a storage media (image memory card, etc.) that allows
you to specify which of the frames shot using a digital camera are printed and how many prints are made of
each image.
EV:
A number that denotes Exposure Value. The EV is determined by the brightness of the subject and sensitivity
(speed) of the film or CCD. The number is larger for bright subjects and smaller for dark subjects. As the
brightness of the subject changes, a digital camera maintains the amount of light hitting the CCD at a constant
level by adjusting the aperture and shutter speed. When the amount of light striking the CCD doubles, the EV
increases by 1. Likewise, when the light is halved, the EV decreases by 1.
JPEG: Joint Photographics Experts Group
A file format used for compressing and saving color images. The compression ratio can be selected, but the higher the
compression ratio, the poorer the quality of the expanded image.
Motion JPEG:
A type of AVI (Audio Video Interleave) file format that handles images and sound as a single file. Images in
the file are recorded in JPEG format. Motion JPEG can be played back by QuickTime 3.0 or later.
PC Card:
A generic term for cards that meet the PC Card Standard.
PC Card Standard:
A standard for PC cards determined by the PCMCIA.
PCMCIA:
Personal Computer Memory Card International Association (US).
White Balance:
Whatever the kind of the light, the human eye adapts to it so that a white object still looks white. On the other
hand, devices such as digital cameras see a white subject as white by first adjusting the color balance to suit
the color of the ambient light around the subject. This adjustment is called matching the white balance. A
function that automatically matches the white balance is called an Automatic White Balance function.
120 121
Keep out of the reach of small children.
This product could cause injury in the hands
of a child.
Do not use this camera in locations
severely affected by oil fumes, steam,
humidity or dust.
This can cause a fire or electric shock.
Do not leave this camera in places
subject to extremely high temperatures.
Do not leave the camera in locations such
as a sealed vehicle or in direct sunlight.
This can cause a fire.
Do not place heavy objects on the
camera.
This can cause the heavy object to tip over
or fall and cause injury.
Do not move the camera while the AC
power adapter is still connected.
This can damage the power cord or cables
and cause a fire or electric shock.
CAUTIONWARNING
Keep xD-Picture Cards out of the
reach of small children.
Because xD-Picture Cards are small, they
can be accidentally swallowed by small
children. Be sure to store xD-Picture Cards
out of the reach of small children. If a child
accidentally swallows an xD-Picture Card,
seek medical advice immediately
Never attempt to modify or disassemble
the camera. (Never open the casing.)
Do not use the camera when it has been
dropped or the casing is damaged.
This can cause a fire or electric shock.
●Contact your FUJIFILM dealer.
Never attempt to take pictures while in
motion.
Do not use the camera while you are
walking or operating a moving car or other
vehicle.
This can result in you falling down or being
involved in a traffic accident.
Do not heat, modify or attempt to
disassemble the batteries.
Do not drop or subject the batteries to
impacts.
Do not attempt to recharge lithium or
alkaline batteries.
Do not store the batteries with metallic
products.
Any of these actions can cause the
batteries to burst or leak and cause fire or
injury as a result.
Do not touch any metal parts of the
camera during a thunderstorm.
This can cause an electric shock due to
induced current from the lightning discharge.
Do not use the batteries except as
specified.
Load the batteries with the poles positioned
as indicated by the +and _marks.
Use only the batteries or AC power
adapter specified for use with this
camera.
The use of other power sources can cause a fire.
If the battery leaks and fluid gets into
your eyes or comes into contact with
your skin or clothing, this can cause
injury or loss of eyesight. Immediately
flush the affected area thoroughly with
clean water and seek medical treatment.
When discarding or storing batteries,
cover the battery terminals with
insulation tape.
hContact with other metallic objects or
batteries could cause the batteries to
ignite or burst.
WARNING
Do not
disassemble.
WARNING
Safety Notes
122 123
EC Declaration of Conformity
We
Name :Fuji Photo Film (Europe)G.m.b.H.
Address :Heesenstrasse 31
40549 Dusseldorf, Germany
declare that the product
Product Name : FUJIFILM DIGITAL CAMERA FinePix A204
Manufacture’s Name : Fuji Photo Film Co., Ltd.
Manufacture’s Address : 26-30, Nishiazabu 2-chome, Minato-ku,
Tokyo 106-8620, Japan
is in conformity with the following Standards
Safety :EN60950
EMC :EN55022 :1998 Classe B
EN55024 :1998
EN61000-3-2 :1995 +A1:1998 +A2:1998
following the provision of the EMC Directive (89/336/EEC, 92/31/EEC and
93/68/EEC)and Low Voltage Directive (73/23/EEC).
Dusseldorf, Germany September 1, 2002
Place Date Signature/Managing Director
Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA
CAUTION
Do not cover or wrap the camera or the
AC power adapter in a cloth or quilt.
This can cause heat to build up and distort
the casing or cause a fire.
Remove the batteries and disconnect
the AC power adapter when you are
cleaning the camera or if you intend to
leave the camera unused for a long
period.
Failure to do so can cause a fire or electric
shock.
Using a flash too close to a person’s
eyes may temporarily affect the eyesight.
Take particular care when photographing
infants and young children.
When an xD-Picture Card is removed,
the card may fly completely out of the
slot. Use your finger to stop the card
flying out before removing the card.
If an xD-Picture Card is allowed to fly out, it
could hit someone and cause injury.
Request regular internal testing and
cleaning for your camera.
Build-up of dust in your camera can cause
a fire or electric shock.
hContact your FUJIFILM dealer to request
internal cleaning every 2 years.
CAUTION
Safety Notes
125124
IMPORTANT
Be sure to read this page before using theSoftware.
NOTICE
BEFORE OPENING THE PACKAGE OF CD-ROM PROVIDED BY
FUJI PHOTO FILM CO., LTD., PLEASE READ THIS END USER
LICENSE AGREEMENT CAREFULLY. ONLY IF YOU DO AGREE TO
THIS AGREEMENT, YOU WILL BE ABLE TO USE THE SOFTWARE
RECORDED ON THE CD-ROM. BY OPENING THE PACKAGE, YOU
ACCEPT AND AGREE TO BE BOUND BY THIS AGREEMENT.
End User License Agreement
T
his End User License Agreement (“Agreement”) is an agreement between Fuji Photo
Film Co., Ltd. (“FUJIFILM”) and you, which sets forth the terms and conditions of the
license granted for you to use the software provided by FUJIFILM.
The CD-ROM contains third party software. In case a separate agreement is provided by
a third party supplier for its software, the provisions of such separate agreement shall
apply to the use of such third party software, prevailing over those of this Agreement.
1. Definitions.
(a) “Media” means the CD-ROM titled “Software for FinePix SX” which is provided
to you together with this Agreement.
(b) “Software” means the software which is recorded on Media.
(c) “Documentation” means the operation manuals of Software and other related
written materials which are provided to you together with Media.
(d) “Product” means Media (including Software) and Documentation collectively.
2. Use of Software.
FUJIFILM grants to you a nontransferable, nonexclusive license:
(a)
to install one copy of Software onto one computer in binary machine executable form;
(b) to use Software on the computer onto which Software is installed; and
(c) to make one backup copy of Software.
3. Restrictions.
3.1 You shall not distribute, rent, lease or otherwise transfer all or any part of
Software, Media or Documentation to any third party without FUJIFILM’s prior
written consent. You also shall not sublicense, assign or otherwise transfer all
or any part of the rights granted to you by FUJIFILM under this Agreement
without FUJIFILM’s prior written consent.
3.2 Except as expressly granted by FUJIFILM hereunder, you shall not copy or
reproduce all or any part of Software or Documentation.
3.3 You shall not modify, adapt or translate Software or Documentation. You also
shall not alter or remove copyright and other proprietary notices that appear on
or in Software or Documentation.
3.4 You shall not, or shall not have any third party, reverse-engineer, decompile,
or disassemble Software.
4. Ownership.
All copyrights and other proprietary rights to Software and Documentation are
owned and retained by FUJIFILM or the third party suppliers as indicated on or in
Software or Documentation. Nothing contained herein shall be construed,
expressly or implicitly, as transferring or granting any right, license, or title to you
other than those explicitly granted under this Agreement.
5. Limited Warranty.
FUJIFILM warrants to you that Media is free from any defect in material and
workmanship under normal use for ninety (90) days from the date of your receipt of
Media. Should Media not meet the foregoing warranty, FUJIFILM shall replace
such defective Media with other Media bearing no defect. FUJIFILM’s entire liability
and your sole and exclusive remedy with regard to any defect in Media shall be
expressly limited to such FUJIFILM’s replacement of Media as provided herein
6. DISCLAIMER OF WARRANTY.
EXCEPT AS PROVIDED IN SECTION 5 HEREIN, FUJIFILM PROVIDES
PRODUCT “AS IS” AND WITHOUT WARRANTIES OF ANY KIND, EXPRESS OR
IMPLIED. FUJIFILM SHALL MAKE NO WARRANTY, EXPRESS, IMPLIED OR
STATUTORY, AS TO ANY OTHER MATTERS, INCLUDING, BUT NOT LIMITED
TO NON-INFRINGEMENT OF ANY COPYRIGHT, PATENT, TRADE SECRET,
OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY,
MARCHANTABILITY, OR FITNESS FOR ANY PARTICULAR PURPOSE.
7. LIMITATION OF LIABILITY.
IN NO EVENT SHALL FUJIFILM HAVE ANY LIABILITY FOR ANY GENERAL,
SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS OR LOST SAVINGS)
INCURRED FROM THE USE OF OR INABILITY TO USE PRODUCT EVEN IF
FUJIFILM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
8. No export.
You acknowledge that neither Software nor any part thereof, will be transferred, or
exported to any country or used in any manner in violation of any export control
laws and regulations to which Software is subject.
9. Termination.
In case you breach any of the terms and conditions hereof, FUJIFILM may
immediately terminate this Agreement without any notice.
10. Term.
This Agreement is effective until the date when you cease to use
Software, unless earlier terminated in accordance with Section 9 hereof.
11. Obligation upon termination.
Upon termination or expiration of this Agreement, you shall, at your own
responsibility and expense, delete or destroy immediately all Software
(including its copies), Media and Documentation.
12. Governing Law.
This Agreement shall be governed by and construed in accordance with
laws of Japan.
Memo
Printed in Japan FGS-204107-FG
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan
Printed on recycled paper.

Navigation menu