Fujitsu Client Computing WB0022 Lifebook B Series w/ WM3B2915ABG 11ABG WLAN & BT User Manual Appendix H 1

Fujitsu Limited Lifebook B Series w/ WM3B2915ABG 11ABG WLAN & BT Appendix H 1

Contents

users manual 1

FCC ID: EJE-WB0022 (IC: 337J-WB0022) Report No. M050754_Cert_ WM3B2915ABG _DTS_BT EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au APPENDIX H USER MANUAL (PART 1)
CopyrightCopyright and Trademark InformationFujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.Microsoft, MS-DOS, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.PCMCIA is a trademark of the Personal Computer Memory Card International Association.Intel, Pentium, and SpeedStep are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.Netscape is a registered trademark of Netscape Communications Corporation.Adobe, Acrobat, and Acrobat Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.All other trademarks mentioned herein are the property of their respective owners.© Copyright 2005 Fujitsu Computer Systems CorporationAll rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu Computer Systems Corporation. No part of this publi-cation may be stored or transmitted in any electronic form without the written consent of Fujitsu Computer Systems Corporation.B6FH-6061-01EN-00W a rn i n gHandling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Was h hands after handling.DECLARATION OF CONFORMITYaccording to FCC Part 15Responsible Party Name: Fujitsu Computer Systems CorporationAddress: 1250 E. Arques Avenue, M/S 122Sunnyvale, CA 94085Telephone: (408) 746-6000Declares that product: Model Configurations:LifeBook B6110 Complies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:(1) This device must not be allowed to cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.B Series.book Page 1 Friday, April 22, 2005 2:51 PM
LifeBook B SeriesIMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed Class 2 Adapters with an output rating of 16 V DC, with a current of 3.75 A.AC Adapter output polarity:When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:■Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.■Avoid using the modem during an electrical storm. There may be a remote risk of electric shock from lightning.■Do not use the modem to report a gas leak in the vicinity of the leak.■Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.■To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord.SAVE THESE INSTRUCTIONSFor Authorized Repair Technicians OnlySystem Disposal+Danger of explosion if Lithium (clock) bat-tery is incorrectly replaced. Replace only with the same or equivalent type recom-mended by the manufacturer. Dispose of used batteries according to the manufac-turer’s instruction.For continued protection against risk of fire, replace only with the same type and rating fuse.Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, ORFEDERAL LAWS.B Series.book Page 2 Friday, April 22, 2005 2:51 PM
Table of ContentsFujitsu LifeBook® B Series NotebookTable of Contents1PREFACEPrefaceAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . .3Fujitsu Contact Information . . . . . . . . . . . . . . . . .3Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32GETTING TO KNOW YOUR LIFEBOOK NOTEBOOKOverviewUnpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Locating the Controlsand ConnectorsTop and Front Components . . . . . . . . . . . . . . . . .8Left-Side Panel Components . . . . . . . . . . . . . . . .9Right-Side Panel Components . . . . . . . . . . . . . .10Bottom Components . . . . . . . . . . . . . . . . . . . . .11Rear Panel Components . . . . . . . . . . . . . . . . . . .12Status Indicator PanelPower Indicator . . . . . . . . . . . . . . . . . . . . . . . . .13AC Adapter Indicator . . . . . . . . . . . . . . . . . . . . .13Battery Level Indicators . . . . . . . . . . . . . . . . . . .13Battery Charging Indicator . . . . . . . . . . . . . . . . .14HDD/Removable Media Drive Indicator . . . . . . .14PC Card Access Indicators . . . . . . . . . . . . . . . . .14Compact Flash (CF) Card Access Indicators . . . . 14NumLk Indicator. . . . . . . . . . . . . . . . . . . . . . . . .14CapsLock Indicator. . . . . . . . . . . . . . . . . . . . . . .14ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .14Security Indicator . . . . . . . . . . . . . . . . . . . . . . . .14KeyboardUsing the Keyboard . . . . . . . . . . . . . . . . . . . . . .15Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . .15Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .15Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . .15Touchpad Pointing DeviceClicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . .17Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Touchpad Control Adjustment . . . . . . . . . . . . . .18Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . .18Volume ControlControlling the Volume . . . . . . . . . . . . . . . . . . .20LifeBook Security/Application PanelSetting up Your LifeBook Security Panel . . . . . . .21Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Operating the Security/ Application Panel . . . . .22Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Uninstalling the Security Panel Application . . . . .22Launching Applications with Application Panel . .233GETTING STARTED WITH YOUR LIFEBOOK NOTEBOOKPower SourcesConnecting the Power Adapters . . . . . . . . . . . . .27Display PanelOpening the Display Panel . . . . . . . . . . . . . . . . .28Adjusting Display Panel Brightness . . . . . . . . . . .28Closing the Display Panel . . . . . . . . . . . . . . . . . .28 B Series.book Page 3 Friday, April 22, 2005 2:51 PM
LifeBook B SeriesStarting Your LifeBook NotebookPower On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . 29BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . 29Booting the System . . . . . . . . . . . . . . . . . . . . . . 30Activating Additional Utilities . . . . . . . . . . . . . . . 30Registering Your LifeBook notebook . . . . . . . . . 31Power ManagementSuspend/Resume Button . . . . . . . . . . . . . . . . . . 32Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 32Hibernate Mode. . . . . . . . . . . . . . . . . . . . . . . . . 33Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . 33Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . 33Windows Power Management . . . . . . . . . . . . . . 33Restarting the System. . . . . . . . . . . . . . . . . . . . . 33Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344USER-INSTALLABLE FEATURESLithium ion BatteryRecharging the Batteries. . . . . . . . . . . . . . . . . . . 37Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 38External Floppy Disk DriveConnecting an Optional Floppy Disk drive . . . . . 39Loading a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 39Ejecting a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 39Preparing a Disk for Use. . . . . . . . . . . . . . . . . . . 39PC CardsInstalling PC Cards . . . . . . . . . . . . . . . . . . . . . . . 41Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . 41Smart Card Reader. . . . . . . . . . . . . . . . . . . . . . . 41Compact Flash CardsInstalling Compact Flash Cards. . . . . . . . . . . . . . 42Removing Compact Flash Cards. . . . . . . . . . . . . 43Memory Upgrade ModuleInstalling a Memory Module . . . . . . . . . . . . . . . 44Removing a Memory Module. . . . . . . . . . . . . . . 44Checking the New Memory Capacity. . . . . . . . . 45Port ReplicatorPort Replicator Components . . . . . . . . . . . . . . . 46Attaching Port Replicator . . . . . . . . . . . . . . . . . . 46Detaching Port Replicator . . . . . . . . . . . . . . . . . 46Device PortsModem (RJ-11) Jack . . . . . . . . . . . . . . . . . . . . . 48Internal LAN (RJ-45) jack . . . . . . . . . . . . . . . . . . 48Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Universal Serial Bus 2.0 Ports . . . . . . . . . . . . . . . 48Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 48Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 48External Monitor Port . . . . . . . . . . . . . . . . . . . . 495TROUBLESHOOTINGTroubleshootingIdentifying the Problem . . . . . . . . . . . . . . . . . . . 53Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . 53Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 54Power On Self Test Messages . . . . . . . . . . . . . . 61Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 62Restoring Pre-installed SoftwareRestoring the Factory Image . . . . . . . . . . . . . . . 63Automatically Downloading Driver Updates. . . . 646CARING FOR YOUR LIFEBOOK NOTEBOOKCare and MaintenanceLifeBook Notebook . . . . . . . . . . . . . . . . . . . . . . 67Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Floppy Disks and Drives . . . . . . . . . . . . . . . . . . . 68CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68PC/CF Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . 69B Series.book Page 4 Friday, April 22, 2005 2:51 PM
Table of Contents7SYSTEM SPECIFICATIONSSpecificationsConfiguration Label . . . . . . . . . . . . . . . . . . . . . .73Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . .73Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Mass Storage Device Options. . . . . . . . . . . . . . .73Integrated Pointing Device . . . . . . . . . . . . . . . . .73LifeBook Security/Application Panel . . . . . . . . . .74Security Features . . . . . . . . . . . . . . . . . . . . . . . .74Communications . . . . . . . . . . . . . . . . . . . . . . . .74Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .74Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74Dimensions and Weight . . . . . . . . . . . . . . . . . . .74Environmental Requirements . . . . . . . . . . . . . . .74Popular Accessories . . . . . . . . . . . . . . . . . . . . . .74Pre-Installed Software . . . . . . . . . . . . . . . . . . . .75Learning About Your Software . . . . . . . . . . . . . .758GLOSSARY/REGULATORYGlossaryGlossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79RegulatoryRegulatory Information . . . . . . . . . . . . . . . . . . .84APPENDIX A: USING THE WIRELESS LAN DEVICEBefore Using the Wireless LANWireless LAN Modes Using this Device. . . . . . . .90Wireless Network Considerations . . . . . . . . . . . .91Deactivating the WLAN Device . . . . . . . . . . . . .91Activating the WLAN Device . . . . . . . . . . . . . . .92Configuration of the WLAN DeviceFlow of Operations. . . . . . . . . . . . . . . . . . . . . . .93Configuration Using Atheros Client Utility . . . . .93Connection to the network. . . . . . . . . . . . . . . . .94Troubleshooting the WLANTroubleshooting Table . . . . . . . . . . . . . . . . . . . .97Wireless LAN GlossaryGlossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98IP address informationAbout IP Addresses . . . . . . . . . . . . . . . . . . . . .100SpecificationsSpecification . . . . . . . . . . . . . . . . . . . . . . . . . . .101Using the Bluetooth DeviceWhat is Bluetooth. . . . . . . . . . . . . . . . . . . . . . .102Where to Find Information About Bluetooth . .102APPENDIX B: SECURITY DEVICE USER’S GUIDEFingerprint Sensor DeviceIntroducing the Fingerprint Sensor Device . . . .105Getting Started. . . . . . . . . . . . . . . . . . . . . . . . .105Installing OmniPass . . . . . . . . . . . . . . . . . . . . .105User Enrollment . . . . . . . . . . . . . . . . . . . . . . . .106Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . .107Configuring OmniPass . . . . . . . . . . . . . . . . . . .109OmniPass Control Center. . . . . . . . . . . . . . . . .110Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .111Trusted Platform Module InstallationTPM Installation . . . . . . . . . . . . . . . . . . . . . . . .112INDEX Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113B Series.book Page 5 Friday, April 22, 2005 2:51 PM
LifeBook B SeriesB Series.book Page 6 Friday, April 22, 2005 2:51 PM
11PrefaceB Series.book Page 1 Friday, April 22, 2005 2:51 PM
2LifeBook B SeriesB Series.book Page 2 Friday, April 22, 2005 2:51 PM
3PrefacePrefaceABOUT THIS GUIDEThe LifeBook® B Series notebook from Fujitsu Computer Systems is a powerful notebook computer. It is powered by an Intel® Pentium® M microprocessor, has a built-in 12.1" color touch screen display, and brings the computing power of a desktop personal computer to a portable environment.This manual explains how to operate your LifeBook notebook’s hardware and built-in system software.Your computer comes with Microsoft Windows® XP Home or Windows XP Professional pre-installed.Your notebook is a completely self-contained unit with an active-matrix (TFT) color LCD touch screen display. It has a powerful interface that enables it to support a variety of optional features.Conventions Used in the GuideKeyboard keys appear in brackets. Example: [Fn], [F1], [Esc], [Enter] and [Ctrl].Pages with additional information about a specific topic are cross-referenced within the text.Example: (See page xx.)On screen buttons or menu items appear in boldExample: Click OK to restart your notebook.DOS commands you enter appear in Courier type. Example: Shutdown the computer?FUJITSU CONTACT INFORMATIONService and SupportYou can contact Fujitsu Computer Systems Service and Support the following ways:■Toll free: 1-800-8Fujitsu (1-800-838-5487)■Fax: 408-764-2724 ■E-mail: 8fujitsu@us.fujitsu.com ■Web site: http://www.computers.us.fujitsu.com/supportBefore you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:■Product name■Product configuration number■Product serial number■Purchase date■Conditions under which the problem occurred■Any error messages that have occurred■Type of device connected, if anyFujitsu OnlineYou can go directly to the online Fujitsu Product catalog for your notebook by clicking on the Fujitsu Weblinks -> LifeBook Accessories Web Site link, located in the Windows Start menu.You can also reach Fujitsu Service and Support online by clicking on the Fujitsu Weblinks -> Fujitsu Service and Support link, located in the Windows Start menu.WARRANTYYour LifeBook notebook is backed by an International Limited Warranty and includes toll-free technical support. Check the service kit that came with yournotebook for warranty terms and conditions.The point icon highlights information that will enhance your understanding of the subject material.The caution icon highlights information that is important to the safe operation of your computer, or to the integrity of your files. Please read all caution information carefully.The warning icon highlights information that can be hazardous to either you, your LifeBook notebook, or your files. Please read all warning information carefully.You must have an active internet connection to use the online URL links.B Series.book Page 3 Friday, April 22, 2005 2:51 PM
4LifeBook B Series – Section OneB Series.book Page 4 Friday, April 22, 2005 2:51 PM
52Getting to KnowYour LifeBookB Series.book Page 5 Friday, April 22, 2005 2:51 PM
6LifeBook B SeriesB Series.book Page 6 Friday, April 22, 2005 2:51 PM
7Getting to Know Your LifeBook Figure 2-1. Fujitsu LifeBook B Series notebookOverviewThis section describes the components of your Fujitsu LifeBook B Series notebook. We strongly recommend that you read it before using your notebook, even if you are already familiar with notebook computers.UNPACKINGWhen you receive your LifeBook notebook, unpack it carefully, and compare the parts you have received with the items listed below.For a pre-configured model you should have:■LifeBook B Series notebook (Figure 2-1)■AC adapter with AC power cord (Figure 2-2)■Phone/Modem (RJ-11) telephone cable■Stylus (located in stylus holder)■Driver and Application Restore CD■Restore DVD■Getting Started Guide■User’s Guide (this document)■International Limited Warranty Brochure■Certificate of AuthenticityDepending upon the configuration of your notebook, you will have one of the following battery configurations: ■One main high-capacity Lithium ion battery (pre-installed), or,■One main Lithium ion battery pre-installed and one spare main high-capacity Lithium ion batteryYou may also have one or more of the following devices in the box:■External USB Floppy Disk Drive (Figure 2-4),and/or,■Port Replicator (Figure 2-3) Figure 2-2. AC AdapterFigure 2-3. Optional Port ReplicatorFigure 2-4. Optional External USB Floppy Disk DriveB Series.book Page 7 Friday, April 22, 2005 2:51 PM
8LifeBook B Series – Section TwoFigure 2-5. LifeBook notebook with display openLocating the Controlsand ConnectorsTOP AND FRONT COMPONENTSThe following is a brief description of your LifeBook notebook’s top and front components. (Figure 2-5)Display Panel LatchThe display panel latch locks and releases the display panel. Touch Screen Display PanelThe display panel is a color LCD panel with back lighting for the display of text and graphics and touch screen functionality. Status Indicator PanelThe Status Indicator Panel displays symbols that corre-spond with a specific component of your LifeBook note-book. See “Status Indicator Panel” on page 13. LifeBook Security/Application PanelThe Security/Application Panel provides hardware secu-rity and one-touch application launch capability. See “LifeBook Security/ Application Panel” on page 21. Suspend/Resume ButtonThe Suspend/Resume button allows you to suspend notebook activity without powering off, resume your notebook from standby mode, and power on your note-book when it has been shut down from the Windows operating system. See “Power On” on page 29.Stereo SpeakersThe built-in dual speakers allow for stereo sound. Built-in MicrophoneThe built-in microphone allows you to input or record mono audio.KeyboardA full-function keyboard with dedicated Windowskeys. See “Using the Keyboard” on page 15.Touchpad Pointing DeviceThe Touchpad pointing device consists of two mouse-like buttons, a scroll button, and a cursor control pad. Note that the scroll button may be replaced by an optional fingerprint recognition sensor, depending upon your system configuration. The optional finger-print recognition sensor allows you to start your system by swiping your finger over the sensor. See “Touchpad Pointing Device” on page 17.DisplayStatusKeyboardLifeBookTouchpad StereoPanel Latch IndicatorPanel Security/ApplicationPanel Pen GarageSuspend/ResumeButtonTouch ScreenDisplay PanelScroll Button or optionalFingerprint RecognitionSensor (pictured)Built-inMicrophonePointing DeviceSpeakersB Series.book Page 8 Friday, April 22, 2005 2:51 PM
9Getting to Know Your LifeBookFigure 2-6. LifeBook notebook left-side panelLEFT-SIDE PANEL COMPONENTSFollowing is a brief description of your LifeBook note-book’s left-side components. (Figure 2-6)Modem (RJ-11) Telephone PortThe Modem (RJ-11) telephone port is for attachinga telephone line to the internal multinational 56K modem.PC Card SlotThe PC Card Slot allows you to install a Type I or Type II PC Card. See “PC Cards” on page 41.PC Card Eject ButtonThe PC Card eject button allows you to remove PC Cards from the PC Card slot. See “PC Cards” on page 41.Microphone JackThe microphone jack allows you to connect an external mono microphone. See “Microphone Jack” on page 48.Headphone JackThe headphone jack allows you to connect headphones or powered external speakers. See “Headphone Jack” on page 48.DC Power JackThe DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your notebook and charge the internal Lithium ion Battery.PC Card SlotPC Card Eject ButtonHeadphone JackMicrophone Jack Modem Port DC Power JackThe internal multinational modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook notebook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum upload speed is 33600bps. B Series.book Page 9 Friday, April 22, 2005 2:51 PM
10LifeBook B Series – Section TwoFigure 2-7. LifeBook notebook right-side panelRIGHT-SIDE PANEL COMPONENTSFollowing is a brief description of your LifeBook note-book’s right-side components.StylusThe stylus is used as the pointing device for the touch screen. Compact Flash Card Eject ButtonAllows you to eject a compact flash card. Compact Flash Card SlotAllows you to insert a compact flash (CF) card. See “Compact Flash Cards” on page 42.USB 2.0 PortsThe two Universal Serial Bus (USB) 2.0 ports allow you to connect Universal Serial Bus devices. See “Universal Serial Bus 2.0 Ports” on page 48.Anti-theft Lock SlotThe anti-theft lock slot allows you to attach an optional physical locking device.USB 2.0 PortsCompact Flash Compact Flash Anti-theft Card SlotCard Eject Button Lock SlotStylusB Series.book Page 10 Friday, April 22, 2005 2:51 PM
11Getting to Know Your LifeBookFigure 2-8. LifeBook notebook bottom panelBOTTOM COMPONENTSFollowing is a brief description of your LifeBook note-book’s bottom panel components. Docking Port ConnectorThis connector allows you to connect the optional Port Replicator. Air VentsThe air vents are used to cool the system to prevent over-heating.Memory Upgrade CompartmentYour LifeBook notebook comes with high speed Synchronous Dynamic RAM (SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your notebook, hence improving overall performance. See “Memory Upgrade Module” on page 44.Hard Disk Drive CoverThe hard disk drive cover protects the hard disk drive. Under normal circumstances, you should never remove this cover unless you are replacing a hard disk drive.Lithium ion Battery PackThe battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery. See “Lithium ion Battery” on page 37.Battery Pack LatchesThe battery pack latches are used to secure and release the Lithium ion battery pack. See “Lithium ion Battery” on page 37.Main Unit and Configuration LabelThe configuration label shows the model number and other information about your LifeBook notebook. In addition, the configuration portion of the label has the serial number and manufacturer information that you will need to give your support representative. It identi-fies the exact version of various components of your notebook. Memory Main Unit andLithium ion Battery Pack LatchesDocking Port ConnectorConfigurationLabel(approximate location)Battery PackUpgradeCompartmentAir VentsHard DiskDrive CoverTo protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used. Do not operate the notebook in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.B Series.book Page 11 Friday, April 22, 2005 2:51 PM
12LifeBook B Series – Section TwoFigure 2-9. LifeBook notebook rear panelREAR PANEL COMPONENTSFollowing is a brief description of your LifeBook note-book’s right-side components. (Figure 2-7)External Monitor PortThe external monitor port allows you to connect an external VGA or SVGA CRT monitor. Note that when the optional Port Replicator is attached to the system, you must use the external monitor port on the Port Replicator rather than the port on the system. See “External Monitor Port” on page 49.LAN (RJ-45) JackThe optional internal LAN (RJ-45) port is used for an internal Fast Ethernet (10/100/1000 Base-T/Tx) Gigabit connection. See “Internal LAN (RJ-45) jack” on page 48.Wireless LAN/Bluetooth On/Off SwitchAllows you to turn the optional Wireless LAN or Blue-tooth devices on and off. This is present only on systems with optional wireless LAN or Bluetooth device installed. LAN (RJ-45) Port External Monitor Port Wireless LAN/ BluetoothOn/Off SwitchB Series.book Page 12 Friday, April 22, 2005 2:51 PM
13Getting to Know Your LifeBookFigure 2-10. Status Indicator PanelStatus Indicator PanelThe Status Indicator displays symbols that correspond with a specific component of your LifeBook notebook. These symbols tell you how each of those components are operating. (Figure 2-10)POWER INDICATORThe Power indicator symbol states whether your system is operational. It has several different states, each of which tells you what mode your notebook is in at that time.■Steady On: This means that there is power to your notebook and that it is ready for use.■Flashing: This means that your notebook is in Standby mode.■Steady Off: This means that your system is either in Hibernate mode, or that your notebook has been turned off.If you are charging your battery, the Power indicator symbol will remain on even if your LifeBook notebook is shut off. The Power indicator symbol will also remain on if you have either adapter connected.AC ADAPTER INDICATORThe AC Adapter indicator states whether your notebook is operating from the AC adapter, the Auto/Airline adapter or the batteries. This icon has two different states that can tell you what power source your note-book is using.■On: This means that either of the adapters are currently in use.■Off: Power is only coming from the batteries, andyou do not have an adapter connected.BATTERY LEVEL INDICATORSThe Battery Level indicators state whether or not the primary Lithium ion battery is installed. In addition, this symbol states how much charge is available within the installed battery. The symbol will only be displayed for a battery that is currently installed in your notebook. (Figure 2-11)Figure 2-11. Battery Level IndicatorBattery Hard Drive AccessPC Card Access NumLk ScrLkSecurityCapsLkPowerAC Compact FlashAdapterBatteryChargingLevelCard Access76%–100% Charging76%–100%51%–75%26%–50%11%–25%Low Warning <11%Critical Low or Dead BatteryShorted BatteryB Series.book Page 13 Friday, April 22, 2005 2:51 PM
14LifeBook B Series – Section TwoBATTERY CHARGING INDICATORLocated to the left of the Battery Level indicator is a small arrow symbol. This symbol states whether the battery is charging. This indicator will flash if the battery is too hot or cold to charge.HARD DRIVE OR REMOVABLEMEDIA DRIVE ACCESS INDICATORThe Hard Drive Access indicator states whether your internal hard drive is being accessed.PC CARD ACCESS INDICATORSThe PC Card Access indicator states whether or not your notebook is accessing a PC Card. The indicator will flash if your software tries to access a PC Card even if there is no card installed. See “PC Cards” on page 41.COMPACT FLASH (CF) CARD ACCESS INDICATORSThe Compact Flash Card Access indicator states whether or not your notebook is accessing a Compact Flash Card. The indicator will flash if your software tries to access a Compact Flash Card even if there is no card installed. See “Compact Flash Cards” on page 42.NUMLK INDICATORThe NumLk indicator states that the integral keyboard is set in ten-key numeric keypad mode. CAPSLOCK INDICATORThe CapsLock indicator states that your keyboard is set to type in all capital letters. SCRLK INDICATORThe ScrLk indicator states that your scroll lock is active. SECURITY INDICATORThe Security Indicator flashes (if a password was set) when the system resumes from Off or Standby modes. You must enter the password that was set in the Security Panel before your system will resume operation.A shorted battery is damaged and must be replaced. (Figure 2-11) If there is no battery activity, the power adapters are not connected, and the power is Off, the Battery Level indicators will also be off.Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged.12B Series.book Page 14 Friday, April 22, 2005 2:51 PM
15Getting to Know Your LifeBookFigure 2-12. KeyboardKeyboardUSING THE KEYBOARDYour LifeBook notebook has an integral 82-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys. (Figure 2-12)■Numeric keypad: Your notebook allows certain keys to serve dual purposes, both as standard characters and as numeric and mathematical keys. The ability to tog-gle between the standard character and numerical keys is controlled through the [NumLk] key.■Cursor keys: Your keyboard contains four arrowkeys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. ■Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. ■Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.NUMERIC KEYPADCertain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] key. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ),multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary func-tions. (Figure 2-12) WINDOWS KEYSYour LifeBook notebook has two Windows keys: a Start key and an Application key. The Start key displays the Start menu. This button functions the same as your onscreen Start menu button. The Application key func-tions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows documentation for additional informa-tion regarding the Windows keys.) (Figure 2-12)CURSOR KEYSThe cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right). (Figure 2-12)FUNCTION KEYSYour LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. (Figure 2-12)[Fn] KeyThe [Fn] key provides extended functions for thenotebook and is always used in conjunction with another key. Fn KeyFunction KeysNumeric Keypad Application Key Cursor Start KeyKeys(outlined in black) B Series.book Page 15 Friday, April 22, 2005 2:51 PM
16■[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.■[Fn+F4]: Pressing [F4] while holding [Fn] will toggle the touch pad on and off. Note that the [Fn+F4] com-bination only works if Manual Setting is selected in the BIOS. (See )■[Fn +F5]: Pressing [F5] while holding [Fn] allows you to toggle between video compensation and no compensation. (Video compensation controls spacing on the display. When it is enabled, displays with less than 1024 x 768 or 800 x 600 pixel resolution will still cover the entire screen.)■[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.■[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.■[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your LifeBook notebook.■[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your LifeBook notebook.■[Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, both built-in display panel and external monitor or external moni-tor only.B Series.book Page 16 Friday, April 22, 2005 2:51 PM
17Getting to Know Your LifeBookFigure 2-13. Touchpad pointing deviceTouchpad Pointing DeviceThe Touchpad pointing device comes built into your LifeBook notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a scrolling button, and left and right buttons. The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger. The scrolling button allows you to navigate quickly through pages (Note that in some LifeBook configura-tions, the scrolling button is replaced by a Fingerprint Recognition Sensor. The left and right buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending on the application that is being used. (Figure 2-13)CLICKINGClicking means pushing and releasing a button. To left-click, move the cursor to the item you wishto select, press the left button once, and then immedi-ately release it. (Figure 2-14) You can also perform the clicking operation by tapping lightly on the Touchpad once. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. Figure 2-14. ClickingDOUBLE-CLICKINGDouble-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button (Figure 2-15). To double-click, move the cursor to the item you wish to select, press the left button twice, and then immediately release it. You can also perform the double-click opera-tion by tapping lightly on the Touchpad twice.Figure 2-15. Double-clickingCursor ControlLeft ButtonRight ButtonScrolling button oroptional FingerprintRecognition Sensor(pictured)B Series.book Page 17 Friday, April 22, 2005 2:51 PM
18LifeBook B Series – Section TwoDRAGGINGDragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor tothe item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap. Next, move the object to its new location by moving your finger across the Touchpad, and then releasing your finger. (Figure 2-16)Figure 2-16. DraggingTOUCHPAD CONTROL ADJUSTMENTIf you need to change or adjust any of the touchpad control functions, you can customize them from the Mouse properties dialog box in the Control Panel. Click on Start, select Settings > Control Panel, then double-click Mouse. TOUCH SCREENThe integrated touch screen allows you to use either the included stylus, or your fingertip, as a pointing device. You can use the stylus to click, double-click, drag items and icons, or to draw like a pen or pencil in applications that support this behavior, such as drawing or painting programs. See the documentation that came with your application for details. (Figure 2-17)Figure 2-17. Using the Stylus with the Touch ScreenRemoving the StylusThe stylus is located on the right side of the system, towards the front (Figure 2-18). To remove the stylus, press the end of it into the stylus holder; this will disen-gage it, allowing it to pop out.Figure 2-18. Removing the StylusClickingTo left-click, touch the object you wish to select, then lift the stylus tip immediately. You also have the option to perform the left-click operation by tapping lightly with your finger on the touch screen once. (Figure 2-19)To right-click, go to Start -> Control Panel -> Touch Panel. From that window, you can specify a right button ■If the interval between clicks is too long, the double-click will not be executed.■Parameters for the Touchpad can be adjusted from the Mouse Properties dialog box located in the Windows Control Panel.To purchase additional or replacement styluses, visit Fujitsu’s accessories web site at: http://us.fujitsu.com/computers.To avoid potential scratching and damage, never use anything but the included stylus or your finger with the touch screen.B Series.book Page 18 Friday, April 22, 2005 2:51 PM
19Getting to Know Your LifeBooktool by using the Touch Panel Configuration Control button prior to the desired right mouse click. It can be used two ways: by holding down the key or by pressing the key once.Figure 2-19. Clicking the Touch ScreenDouble-ClickingTo double-click, touch the item twice, and then immedi-ately remove the stylus tip. You also have the option to perform the double-click operation by tapping lightly with your finger on the touch screen twice. (Figure 2-20)Figure 2-20. Double-clicking the Touch ScreenDraggingDragging means touching the screen with the stylus, moving and then lifting the stylus. To drag, tap the touch screen twice with your stylus over the item you wish to move, making sure to leave the stylus on the screen after the final tap. Next, move the item to its new location by moving the stylus across the screen, and then lifting the stylus to release it. Dragging can also be done using your fingertip. (Figure 2-21)Figure 2-21. Dragging on the Touch ScreenRight-clickingIt is possible for you to perform right-click functions with the stylus.1. Click Start -> Control Panel -> Touch Panel.2. Select the Right button simulation tab. 3. Check the "Enable the right click simulation" box.4. Choose which key you prefer to enable the right-click function: Ctrl Key, Shift Key, or Alt Key.Calibrating the Touch ScreenIn order to ensure accurate tracking between the stylus and cursor, you should run the Touch Screen Calibra-tion Utility before you use the touch screen for the first time, or after you change the display resolution.To run the calibration utility:1. Go to [Start] -> Control Panel, and double-click on the Touch Panel icon. 2. Select the Calibration tab and click the [Calibrate Now] button. 3. Adjust the display of your notebook to a comfortable angle and find the red (+) symbol in the upper-left corner of the display.4. Using the stylus, touch the screen directly on the (+) symbol, then lift the stylus. When you lift the stylus tip, the (+) symbol will move to the next location.4. Repeat step 4 until you have selected a total of nine symbols. This is the minimum number of points necessary to calibrate your touch screen.5. Once you have selected the nine symbols, click the [Update] button to return to the Touch Panel Settings screen.If the interval between taps is too long, thedouble-click will not be executed.B Series.book Page 19 Friday, April 22, 2005 2:51 PM
20LifeBook B Series – Section TwoVolume ControlYour Fujitsu LifeBook notebook has multiple volume controls which interact with each other. CONTROLLING THE VOLUMEThe volume can be controlled in several different ways:■Volume can be set from within the Volume Control on the Taskbar.■Volume can be controlled from the Control Panel by selecting the Sounds and Audio Devices icon. Select the Volume tab and move the slider bar to the desired volume level.■Volume can be controlled with the F8 and F9 function keys. Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your notebook. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your notebook. Volume can be controlled by many volume controls that are set within individual applica-tions.■Certain external audio devices you might connect to your system may have hardware volume controls.Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources. We recommend that you experiment with the various volume controls to discover the optimal sound level.Any software that contains audio files will also contain a volume control of its own. If you install an external audio device that has an independent volume control, the hardware volume control and the software volume control will interact with each other. It should be noted that if you set your software volume to Off, you will override the external volume control setting. There are twenty-six levels through which the volume function keys cycle. B Series.book Page 20 Friday, April 22, 2005 2:51 PM
21Getting to Know Your LifeBookFigure 2-22. LifeBook Security/Application Panel LifeBook Security/Application PanelA unique feature of your LifeBook notebook is the Secu-rity/Application Panel that allows you to secure your notebook from unauthorized use. The Security/Applica-tion Panel also allows you to launch applications with the touch of a button when your system is on.If the security system is activated, upon starting your notebook or resuming from Standby mode the security system requires you to enter a password code using the buttons on the Security/Application Panel. After entering a correct password, your notebook resumes system operation. (Figure 2-22)SETTING UP YOUR LIFEBOOK SECURITY PANELWhen you receive your LifeBook notebook, the security panel application is pre-installed without any pass-words. The following sections provide detailed informa-tion on your security panel, how to set, change or remove passwords.Numbered ButtonsUse these buttons to enter your password.Enter ButtonAfter entering the button strokes, push this button to enter the password into the LifeBook notebook. PASSWORDSThe user and supervisor password may be set on this notebook. A supervisor password is typically the same for all LifeBook notebooks in a working group, office, or company to allow for system management. Individual LifeBook notebooks in a group environment should not use a common password. A password consists of one to five button strokes plus the enter button. A valid stroke consists of pushing one or up to four buttons simulta-neously. The following are valid button strokes: ■Pushing [4] by itself■Pushing [2] and [3] at the same time■Pushing [1], [2], and [4] at the same time■Pushing [1], [2], [3], and [4] at the same timeThe following are valid passwords. The numberswithin braces ({ }) are button strokes using morethan one button. ■{[2]+[3]}, [1], [enter]■[4], [enter]■{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [enter]Setting PasswordsWhen shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the super-visor password before the user password. (1) Application A Button(3) Internet Button(2) Application B Button(4) E-Mail ButtonEnter ButtonB Series.book Page 21 Friday, April 22, 2005 2:51 PM
22LifeBook B Series – Section TwoSetting Supervisor PasswordYou must have set a supervisor password before setting any user passwords. The supervisor password can bypass the user password.1. Go to the Start menu.2. Click on Run.3. Type in:C:\Program Files\Fujitsu\Security Panel Application\Supervisor\FJSECS.EXE, then press [Enter]4. Follow the on-screen instructions to set theSupervisor password.Setting User Password1 Go to the Start menu.2. Click on Programs.3. Click on Security Panel Application andSet User Password.4. Follow the on-screen instructions to set theuser password.OPERATING YOUR LIFEBOOK SECURITY/ APPLICATION PANELThe security lock feature is in effect both when the system resumes from Off or Standby state. You always need to push the Suspend /Resume button to input the user pass-word. Your system will not begin the boot sequence without entering your supervisor/user password.From Off State1. Turn on your system.2. When the Security Indicator flashes, enter the pass-word and press Enter button.For example, if the password is 22222,Press Button Number 2 five times and press Enter button.The LifeBook notebook will boot to normal opera-tion.From Standby State1. Press your Suspend/Resume button.2. When the Security Indicator flashes, enter the pass-word and press Enter button.The notebook should resume normal operation.Incorrect Password EntryIf an invalid supervisor or user password is entered three times in succession, the system will “beep” for about one minute. If a valid password is entered within a minute (while system beeps), the beeping will stop and the note-book will resume normal operation. If no or an invalid password is entered while the system beeps, the system will return to its previous locked state (standby or off) and the Security Indicator will go off. To reactivate the notebook after a password failure, you must press the Suspend/Resume button, then enter a correct password.PRECAUTIONSOpening and Closing the CoverClosing the cover automatically places the notebook into Standby mode. Opening the cover does not automati-cally place the notebook into normal operation. Instead, you must enter the proper security password after pushing the Suspend/Resume button.Low Battery OperationsIf your LifeBook notebook has low battery, pushing the suspend/resume button only turns on the Security Indi-cator. Your notebook does not unlock, the Security Indi-cator turns off after one minute. To resume normal operation, first attach a power supply to the notebook. Then you may unlock the notebook.UNINSTALLING THE SECURITY PANEL APPLICATIONYou have two options when uninstalling the securitypanel application:■Uninstall the security panel application software.This will disable all security feature.■Uninstall the security panel application with password still active. This will not allow any changes to the password. Uninstalling the Security Panel Application SoftwareRemove passwords when User wants no password protection whatsoever and doesn’t want to give anybody the utility to set a password on their computer. In this ■The purpose of supervisor password is to be able to bypass the user password in case the user password is forgotten. The supervisor password alone will not lock the system.■You have to set both the supervisor and user passwords for the security panel to work.You may change or remove the supervisor or user password by repeating the steps defined above.Remember the user password you specified on the Security Panel Application. If you forget the password you will not be able to use your computer. The supervisor password can override the user password.B Series.book Page 22 Friday, April 22, 2005 2:51 PM
23Getting to Know Your LifeBookcase, if passwords (supervisor, user, or both) are set, the passwords must first be cleared before removing the application. To clear passwords, follow same procedure in setting the passwords, except this time, check the “Remove Supervisor (and/or) User Password” box, as appropriate. Click [Next]. Enter the password. When asked to confirm that you want to remove the password, click [OK], then click [Finish]. Removing Security Panel Application withPasswords Still ActiveUsing this feature will not allow any changes tothe password. User: 1. Go to Start Menu, Click on Control Panel.2. Open Add/Remove Programs Properties in the Control Panel. 3. Select the Security Panel Application in the list, and click Add/Remove. 4. When the Confirm File Deletion box appears,click Ye s .Supervisor:1. Go to Start Menu, Click on Control Panel.2. Open Add/Remove Programs Properties in the Control Panel. 3. Select the Security Panel Application forSupervisor in the list, and click Add/Remove. 4. When the Confirm File Deletion box appears,click Ye s .Reinstalling the Security/Application PanelTo reinstall supervisor or user security application, you will need your Drivers and Applications CD. The Utilities\Security Application Panel folder contains two separate folders: Supervisor and User. The setup files for supervisor and user security applications are contained in those folders. 1. Go to the Utilities\Security Application Panel\Supervisor folder on the CD and double-click the setups.exe file. The Installing Security Panel Application window will appear. Follow the instruc-tions on the screen.2. Go to the Utilities\Security Application Panel\User folder on the CD and double-click the setup.exe file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.Supervisor and user passwords can be set via Windows software using the FJSECS.exe and FJSECU.exe files, respectively. FJSECU.exe for the user password cannot run without first setting a supervisor password. You need to run FJSECS.exe first to set the supervisor pass-word. Follow instructions under Setting Passwords on page 21.If you forget both passwords, please contact Fujitsu Computer Systems Service and Support at 1-800-8FUJITSU (1-800-838-5487). Fujitsu Computer Systems Corporation charges a service fee for unlocking a pass-word restricted LifeBook notebook. When calling please have a valid credit card and provide proof of ownership. You will then be given instructions on where to ship your notebook. LAUNCHING APPLICATIONS WITHTHE SECURITY/APPLICATION PANELThe security panel also enables you to launch applications with the touch of a button when your system is on. Pressing any of the buttons will launch a user-defined application. Your notebook is pre-installed with software utilities that let you operate and configure your LifeBook Security /Application Panel. These utilities are found under the Start menu, under Programs, then under Life-Book Application Panel. They include Application Panel Setup, Application Panel Guide, Activate Panel and Deac-tivate Panel. Configuring your LifeBook Application Panel When you start Windows, the LifeBook Application Panel is automatically activated. An icon resembling a finger pressing a button will appear in the system Control Panel. When you see this icon you will know that LifeBook Application Panel is active.As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. To set up the Panel to best suit your needs, we have provided the Application Panel Setup utility that quickly and easily helps you make the most of this valuable feature.To configure your LifeBook Application Panel with Application Panel Setup:1. Click on [Start].2. Click on Control Panel.3. Double-click on the Application Panel icon. The Application Panel setup utility will appear. There are tabs that correspond to the application buttons on the LifeBook Application Panel. When you receive your notebook, these buttons are pre-configured to launch specific programs, as referenced in Chapter 7 of this document.Removing the applications does not remove the password. It simply removes the utility to change/add/remove passwords. To change your password you must reinstall the application.B Series.book Page 23 Friday, April 22, 2005 2:51 PM
24LifeBook B Series – Section TwoTo change an application associated with the Application buttons, click on the tab for the button you would like to reconfigure – for example, Application A. Click on [Browse] or [Go to Start Menu...], scroll down the list of applications, click on the application you wish to launch with this button, and then click OK. The button will now launch the new application.The Internet tab is different. It comes set to launch your Windows default Internet browser (Internet Explorer), unless you have changed this in Windows. In order to reconfigure it to launch another program follow these easy steps:1. Select “Start Other Program” from the “Specify the button action:” box. 2. Click on [Browse] or [Go to Start Menu...].3. Scroll down the list of applications, and then click on the application you wish to launch with this button.4. Click [OK]. The button will now launch the new application. If you want to return to launching your Windows default Internet browser with this button, you need only click on “Default Internet Browser” from the Internet browser box. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application” from this button, you will need to reconfigure it as described above.When you have finished with Application Panel Setup click OK, and the new settings will take effect. You can reconfigure your LifeBook Application Panel as often as you like.Deactivating and Activating the LifeBook Application PanelTo deactivate the LifeBook Application Panel, follow these easy steps:1. Click on [Start].2. Click on Programs.3. Click on LifeBook Application Panel.4. Click on Stop Application Panel.To reactivate, follow the same procedure, except forstep 4. Click on Restart Application Panel instead.The tabs in Application Panel Setup may not be in the same order as the buttons on your LifeBook notebook, please select the tab you wish to change carefully.If your system has dedicated one of the application launcher buttons to be an Internet launcher, the button can still be configured to launch any application you wish, not just an Internet browser.Every time you start Windows the LifeBook Application Panel is activated, even if you deactivated it before you shut down.B Series.book Page 24 Friday, April 22, 2005 2:51 PM
253Getting StartedB Series.book Page 25 Friday, April 22, 2005 2:51 PM
26LifeBook B SeriesB Series.book Page 26 Friday, April 22, 2005 2:51 PM
27Getting StartedFigure 3-1. Connecting the AC AdapterPower SourcesYour LifeBook notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.CONNECTING THE POWER ADAPTERSThe AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter1. Plug the DC output cable into the DC power jackof your notebook.2. Plug the AC adapter into an AC electrical outlet. (Figure 3-1)Connecting the Optional Auto/Airline Adapter1. Plug the DC output cable into the DC power jackon your notebook.2. Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key inthe On or Accessories position.OR3. Plug the Auto/Airline adapter into the DC power jack on an airplane seat.Switching from AC Adapter Power or theAuto/Airline Adapter to Battery Power1. Be sure that you have at least one chargedbattery installed.2. Remove the AC adapter or the Auto/Airline adapter.DC Power JackDC Output CableAC AdapterAC CableThe Lithium ion battery is not charged upon purchase. Initially, you will need to connect either the AC adapter or the Auto/Airline adapter to use your notebook.B Series.book Page 27 Friday, April 22, 2005 2:51 PM
28LifeBook B Series – Section ThreeFigure 3-2. Opening the Display PanelDisplay PanelYour LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of active-matrix technology. OPENING THE DISPLAY PANEL1. Press the Display Panel latch in. This releases the locking mechanism and raises the display slightly. 2. Lift the display backwards, being careful not to touch the screen, until it is at a comfortableviewing angle. ADJUSTING DISPLAY PANEL BRIGHTNESSOnce you have turned on your notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. Adjusting the brightness using the keyboard changes the setting only temporarily. ■[Fn+F6]: Pressing repeatedly will lower thebrightness of your display.■[Fn+F7]: Pressing repeatedly will increase thebrightness of the display.CLOSING THE DISPLAY PANEL1. Holding the edge of your display panel, pull it forward until it is flush with the body of your note-book. 2. Push down until you hear a click. This will engage the locking mechanism and prevent your display panel from opening unexpectedly.Display Panel LatchIf using AC power your brightness setting is set to its highest level by default. If using battery power your brightness setting is set to approximately mid-level by default.The higher the brightness level, the more power the LifeBook notebook will consume and the faster your batteries will discharge. For maximum battery life, make sure that the brightness is set as low as possible.B Series.book Page 28 Friday, April 22, 2005 2:51 PM
29Getting StartedStarting Your LifeBook NotebookPOWER ONSuspend/Resume On buttonThe Suspend/Resume button is used to turn on your LifeBook notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your notebook. Figure 3-3. Pressing the Suspend/Resume ButtonPress the Suspend/Resume button (Figure 3-3). When you are done working you can either leave your Life-Book notebook in Suspend mode (See “Suspend/Resume Button” on page 32.), or you can turn it off (See “Power Off” on page 34.)When you turn on your LifeBook notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LifeBook notebook will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 84. Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.After satisfactory completion of the Power On Self Test (POST), your notebook will load your operating system.BOOT SEQUENCEThe procedure for starting-up your notebook is termed the Bootup sequence and involves your LifeBook note-book’s BIOS. When your notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook. This informa-tion is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your notebook is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.The boot sequence is executed when:■You turn on the power to your notebook.■You restart your notebook from the WindowsShut Down dialog box.■The software initiates a system restart. Example:When you install a new application.■You reset the system by pressing the three keys [CTRL+ALT+DEL]. BIOS SETUP UTILITYThe BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOSis set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your notebook.The BIOS Setup Utility configures:■Device control feature parameters, such as changingI/O addresses and boot devices.■System Data Security feature parameters, suchas passwords.Entering the BIOS Setup UtilityTo enter the BIOS Setup Utility do the following: 1. Turn on or restart your notebook.2. Press the [F2] key once the Fujitsu logo appearson the screen. This will open the main menuof the BIOS Setup Utility with the currentsettings displayed.3. Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings.When you turn on your LifeBook note-book be sure you have a battery installed and charged, or that the AC or Auto/Air-line adapter is connected and has power.Do not carry your LifeBook notebook around with the power on or subject it to shocks or vibration, as you risk damaging your notebook.Suspend/Resume ButtonNever turn off your LifeBook notebook during the Power On Self Test (POST) or it will cause an error message to be displayed the next time you turn on your LifeBook notebook. See “Power On Self Test Mes-sages” on page 61.B Series.book Page 29 Friday, April 22, 2005 2:51 PM
30LifeBook B Series – Section ThreeBIOS GuideA guide to your notebook’s BIOS is available online. Please visit our service and support Web site at http://www.computers.us.fujitsu.com/support. Once there, select User’s Guides under Notebook/Tablet PC Support. Select your system model and click [Go]. Select the BIOS Guide from the menu for your LifeBook series. If you are unsure of your notebook’s BIOS number, refer to your packing slip.BOOTING THE SYSTEM We strongly recommend that you not attach any external devices until you have gone through the initial power-on sequence.When you turn on your LifeBook notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.Designed to accommodate the needs of many users, in many different countries, Windows needs to be config-ured the first time you use them. Windows has three parts: ■Getting Started: You have the opportunity to enter custom information for your configuration file and setup your modem so that your LifeBook notebook will be prepared to dial out. ■Windows License Agreement and Final Settings:You have the opportunity to review the Windows License Agreement.Getting StartedRead the instructions on the screens carefully and fillin the information as directed. You will be asked for such items as the language you wish to use, the country in which you live, your first and last name, and abouthow you dial out from where you will be using your Life-Book notebook. For the modem settings, enter your current location information where you will be using your LifeBook notebook. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button, and you will go directly to the condition of use page.Once you have set up your LifeBook notebook to dial out, Windows will make a free telephone call to test the settings. If the call is unsuccessful, you will be returned to the phone settings page where you may try to fix them. If you are unable to fix the settings, contact Fujitsu Service and Support. See “Fujitsu Contact Information” on page 3. If you would simply like to move on, and register at a later time, you may click the Skip button, and you will go directly to the Condition of Use page.RegistrationIf your connection is successful, you will go to the Registration Confirmation page. On this page simply enter the requested information, and then check the box at the bottom to register your copy of Windows with Microsoft. Once you have finished, click the Next button to continue.You will then go through the Fujitsu registration process. Follow the instructions on the screens, and enter all of the necessary information. Be as specific as possible so that if you need help the service and support team will be able to serve you better.Final SettingsThe first part of your final settings is the Windows End User License Agreement. Read the agreement carefully. When you finish reading you must accept or reject the terms of the agreement and then click on the Next button.ACTIVATING ADDITIONAL UTILITIESIn Windows XP systems, the Click Me! icon is in the Start menu. When you click the Click Me! icon, your system will automatically build the icon tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access. Although the icon remains on the screen, you need invoke it only once.If your data security settings require it, you may be asked for a password before the BIOS main menu will appear.■If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows or to shut down your LifeBook notebook.■You cannot use your LifeBook notebook until you have accepted the License Agreement. If you stop the process your notebook will return to the beginning of the Windows Welcome Process.If you do not register at this time you can do it later simply by double-clicking on the LifeBook Registration icon on your desk-top and following the instructions.If you do not register at this time you can do it later simply by double-clicking on the LifeBook Registration icon on your desk-top and following the instructions.B Series.book Page 30 Friday, April 22, 2005 2:51 PM
31Getting StartedREGISTERING YOUR LIFEBOOK NOTEBOOKHow do I register?With Windows, just follow the on-screen instructions during the Welcome process. If you do not register during the Welcome process you can double-click on the LifeBook Registration icon on your desktop at any time and follow the instructions. You may also register on our Web site:■http://www.computers.us.fujitsu.com/supportYou will need to be set up with an Internet Service Provider (ISP) to use this option.Make sure you have connected a phone line to your modem before you use E-Registration.B Series.book Page 31 Friday, April 22, 2005 2:51 PM
32LifeBook B Series – Section ThreePower ManagementYour LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating condi-tions, such as those for the display brightness. Internal power management for your notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.Besides the options available for conserving battery power, there are also some things that you can do to prevent your notebook battery from running down as quickly. For example, you can create an appropriate power saving profile, put your notebook into Standby mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings.Table 3-1. System Power StatesSUSPEND/RESUME BUTTONWhen your LifeBook notebook is active, the Suspend/Resume button can be used to manually put your Life-Book into Standby mode. Push the Suspend/Resume button when your notebook is active, but not actively accessing anything, and immediately release the button. You will hear two short beeps and your system will enter Standby mode. (See figure 2-5 on page 8 for location).If your notebook is suspended, pushing the Suspend/Resume button will return your notebook to active oper-ation. You can tell whether or not your system is in Standby mode by looking at the Power indicator. See “Power Indicator” on page 13. If the indicator is visible and not flashing, your notebook is fully operational. If the indicator is both visible and flashing, your notebook is in Standby mode. If the indicator is not visible at all, the power is off or your notebook is in Hibernate mode. STANDBY MODEStandby mode in Windows saves the contents of your notebook’s system memory during periods of inactivity by maintaining power to critical parts. This mode will turn off the CPU, the display, the hard drive, and all of the other internal components except those necessary to maintain system memory and allow for restarting. Your notebook can be put in Standby mode by:■Pressing the Suspend/Resume button when your system is turned on.■Selecting Standby from Windows Shut Down menu.■Timing out from lack of activity.■Allowing the battery to reach the Dead BatteryWarning condition.Your notebook’s system memory typically stores the file(s) on which you are working, open application(s) information, and any other data required to support the Power Mode System Activity Events causing system to enter mode stateFully On Mode System is running. CPU, system bus, and all other interfaces operate at full speed.■From Standby mode: System operation resumed (Suspend/Resume button pressed, resume on modem ring, resume on time).■From Hibernation mode: Suspend/Resume button pressed.■From Off mode: Suspend/Resume button pressed.Standby Mode (Suspend-to-RAM)Resume system logic remains powered and RAM remains powered to maintain active data. All other devices are turned off.■Standby timeout occurs.■Suspend request issued by software or by pressing the Suspend/Resume button.■Low battery.Hibernation Mode (Suspend-to-Disk)Windows saves desktop state (including open files and documents) to hard disk. CPU stops. All other devices are turned off.■Suspend timeout occurs.■Clicking Start -> Shut Down -> Hibernate (It may be necessary to Enable Hibernate Support from Windows Power Options.)■Low battery conditionPower OffSystem is fully powered off except for logic components required for Suspend/Resume button and real-time clock operation.■System shutdown.■Low battery conditionB Series.book Page 32 Friday, April 22, 2005 2:51 PM
33Getting Startedoperation(s) in progress. When you resume operation from Standby mode, your notebook will return to the point where it left off. To resume operation, you must use the Suspend/Resume button to resume operation, and there must be an adequate power source available, or your notebook will not resume.HIBERNATE MODEHibernate mode saves the contents of yournotebook’s system memory to the hard drive as a part of the Suspend/Resume mode. Your notebook is pre-configured to perform this function. The Hibernate mode can also be configured through the system BIOS to run in other ways depending on what you need to accomplish. See “BIOS Setup Utility” on page 29.Using Hibernate ModeTo enable or disable the Hibernation feature follow these easy steps:1. From the Start menu, select Settings, and then select Control Panel --> Power Options.2. Select the Hibernate tab, and then select the box to enable or disable this feature.3. Click [Apply].To use Hibernate mode:1. Click the Ctrl-Alt-Del keys.2. Select Shut Down from the top of the window.3. Select Hibernate from the drop down list that appears.DISPLAY TIMEOUT The display timeout is a power management feature. This feature saves power by turning off the display if there is no keyboard or pointer activity for the user selected timeout period. Any keyboard or pointer activity will cause the display to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows Power Management and BIOS setup utility (APM only). See “BIOS Setup Utility” on page 29.HARD DISK TIMEOUTThe hard disk timeout is another one of the power management parameters. This feature saves power by turning off the hard drive if there is no hard drive activity for the user selected timeout period. Any attempt to access the hard drive will cause it to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility (APM only). See “BIOS Setup Utility” on page 29.WINDOWS POWER MANAGEMENT The Power Management icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Management to set the timeout values for turning off the display and hard disks whether you are running the notebook on battery power or one of the adapters. The settings may also be changed in the BIOS (APM only). See “BIOS Setup Utility” on page 29.RESTARTING THE SYSTEMIf your system is on and you need to restart it, be sure that you use the following procedure. 1. Click the Start button, and then click Turn Off Computer.2. Select the Restart option from within the Windows Turn Of f Com puter dial og box.If you are running your LifeBook notebook on battery power, be aware that the battery continues to discharge while your notebook is in Standby mode, though not as fast as when fully operational. ■The Standby or Hibernate modes should not be used with certain PC Cards. Check your PC Card documentation for more information.■Disabling the Suspend/Resume button prevents it from being used to put your notebook in Standby or Hibernate mode. The resume function of thebutton cannot be disabled.■If your notebook is actively accessing information when you enter the Standby or Hibernate mode, changes to open files are not lost. The files are left open and memory is kept active during Standby mode or the memory is trans-ferred to the internal hard drive during Hibernate mode.■When PC Cards or external devices are in use, Save-to-Disk mode cannot return to the exact state prior to suspension, because all of the peripheral devices will be re-initialized when the system restarts.■The main advantage of using the Hiber-nate function is that power is not required to maintain your data. This is particularly important if you will be leav-ing your notebook in a suspended state for a prolonged period of time. The drawback of using Hibernate mode is that it lengthens the power down and power up sequences and resets periph-eral devices.B Series.book Page 33 Friday, April 22, 2005 2:51 PM
34LifeBook B Series – Section Three3. Click OK. Your notebook will shut down and then reboot.POWER OFFBefore turning off the power by choosing Turn Off Computer from the Windows Start menu, check that the Hard Drive, PC Card and the Floppy Disk Drive Access indicators are all Off. (See Figure 2-5 on page 8) If you turn off the power while accessing a disk or PC Card there is a risk of data loss. To ensure that your notebook shuts down without error, use the Windows shut down procedure.Using the correct procedure to shut down from Windows, allows your notebook to complete its opera-tions and turn off power in the proper sequence to avoid errors. The proper sequence is:1. Click the Start button, and then click Turn Off Computer.2. Select the Turn Off option from within the dialog box.If you are going to store your notebook for a month or more see the Care and Maintenance section. Turning off your LifeBook notebook without exiting Windows or turning on your notebook within 10 seconds of the notebook being shut off may cause an error when you start the next time. Be sure to close all files, exit all applications, and shut down your operating system prior to turning off the power. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors.B Series.book Page 34 Friday, April 22, 2005 2:51 PM
354User-Installable FeaturesB Series.book Page 35 Friday, April 22, 2005 2:51 PM
36LifeBook B SeriesB Series.book Page 36 Friday, April 22, 2005 2:51 PM
37User Installable FeaturesLithium ion BatteryYour LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.The Lithium ion battery operating time may become shorter if it is used under the following conditions:■When used at temperatures that exceed a low of 40°F (5°C) or a high of 95°F (35°C). Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range. See “Battery Charging Indicator” on page 14.■When using a high current device such as a modem, CD-ROM drive, or the hard drive. Using the AC adapter when operating such devices will help to conserve your battery life.RECHARGING THE BATTERIESIf you want to know the condition of the primary Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes.The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your notebook and connect the AC orAuto/Airline adapter.There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your notebook into Standby mode, or turn it off while the adapter is charging the battery. See “Power Management” on page 32.Low Battery StateWhen the battery is running low, your notebook will beep every 15 seconds and the Battery Level indicator will flash. If you do not respond to the low battery alarm, the batteries will continue to discharge until they are too low to operate. When this happens there will be a multiple beep alarm and the Battery Level indicator will show a dead battery. Your LifeBook will then go into Standby mode to try and protect your data for as long as possible. There is no guarantee that your data will not be lost once the notebook reaches this point.■Do not leave a faulty battery in your notebook. It may damage your AC adapter, optional Auto/Airline adapter, another battery or your notebook itself. It may also prevent operation of your notebook by draining all avail-able current into the bad battery.■Under federal, state, or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this information else-where, contact your support represen-tative at 1-800-8Fujitsu.Actual battery life will vary based on screen brightness, applications, features, power management settings, battery condition and other customer preferences.CD-ROM drive or hard drive usage may also have a significant impact on battery life. The battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one.Make sure that the Battery Charging indicator and the percentage charge is shown inside the Battery Level icon on the Status Indicator Panel.Using heavy current devices such as a modem or frequent CD-ROM and PCMCIA powered external devices accesses may prevent charging completely.■You may not be able to hear the audio alarm if the volume control is set too low or is turned off by either the hardware or software. However, you will still be able to see the Battery Level indicator flash. Once the low battery alarm occurs you must save all your active data and put your notebook into Standby mode until you can provide a new power source. You should provide a charged battery, an AC power adapter, or Auto/Airline as soon as possible. ■When you are in Standby mode there must always be at least one power source active. If you remove all power sources while your notebook is in Standby mode, any data that has not been saved to the hard drive will be lost.B Series.book Page 37 Friday, April 22, 2005 2:51 PM
38LifeBook B Series – Section FourDead Battery Suspend mode shows on the Status indi-cator just like the normal Standby mode. Once your notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your notebook while an adapter is charging the battery.Shorted BatteriesThe Status Indicator panel uses a symbol inside the battery outline of the Battery Level indicator to display the operating level available in that battery. (See figure 2-11 on page 13) If this display shows a Shorted Battery, it means that the battery is damaged and must be replaced so it does not damage any other parts of your notebook.REPLACING THE BATTERY Your LifeBook B Series notebook comes with one battery pack, but it’s a good idea to purchase a second one. By keeping a spare battery fully charged, you can immedi-ately swap with one that is not charged. The battery can only be replaced by cold-swapping; doing otherwise could result in loss of data. (Cold swapping means swap-ping batteries when the system has been powered down.)Cold-swapping BatteriesTo cold-swap batteries in your battery bay follow these easy steps: (Figure 4-1)1. Have a charged battery ready to install.2. Shut down your notebook and disconnect the AC adapter.Figure 4-1. Removing the Battery3. Push the battery bay release latches inward, then lift the front of the battery away from the battery bay and remove it from the bay.4. Position the new battery in the bay and carefully lay it into the tray. (Figure 4-2) Press it down so that the latches click into place to secure the battery.5. Turn the power on. Figure 4-2. Installing the BatteryBattery Bay Release Latches BatteryIf the Lithium ion battery connector is not fully seated, you may not be able to use your notebook or charge your battery.B Series.book Page 38 Friday, April 22, 2005 2:51 PM
39User Installable FeaturesFigure 4-3. Loading/Ejecting a 3.5” Floppy DiskExternal Floppy Disk Drive**Optional deviceCONNECTING AN OPTIONALEXTERNAL FLOPPY DISK DRIVEYour LifeBook notebook may have an optional external floppy disk drive which can read and write information on removable 1.44MB and 720KB floppy disks.The USB floppy disk drive can be installed while your system is in a suspended state (“warm” connection), while the system is running (“hot” connection), or when the system is off (“cold” connection).Figure 4-4. USB floppy disk drive cable and connection Attach the external USB floppy disk drive by inserting the end of the cable connector into the USB port. See the figure above.See your computer’s User’s Guide to determine the loca-tion of the USB port.Your computer will automatically detect the floppy disk drive and activate it within your system. The drive letters associated with the floppy disk drive will be created and listed under My Computer and Windows Explorer.LOADING A DISKTo load a disk into your disk drive, follow these steps: 1. Orient the disk so that its label is facing upwardsand the shutter side is pointing towards the drive. (Figure 4-3)2. Push the disk into the drive until the Eject button pops out and you hear a click. EJECTING A DISKTo eject a disk from the disk drive, follow these steps:1. Check that the Floppy Disk Drive Access indicatoris inactive.2. Press the Eject button. This will push your disk partially out of the drive.3. Remove the disk.PREPARING A DISK FOR USEBefore you can use a new disk, it needs to be preparedso your notebook knows where to store information. This preparation is called formatting or initializing a disk. You will need to format new disks, unless they are preformatted. (Please refer to your operating system manual for step-by-step instructions on formatting a disk) To prevent accidental erasure of the data stored on a disk, slide the “write protect” tab until a small hole is exposed. This sets the disk into a protected state where nothing can be added or removed. If you want to add or remove data on a protected disk, slide the “write protect” tab to close the small hole. (Figure 4-5)Eject ButtonWhen there is no disk in the drive, the Eject button is flush with your LifeBook notebook.If you eject the disk while the Floppy Disk Drive Access indicator is active, there is a risk of damaging the data on the disk, the disk itself or even the disk drive.B Series.book Page 39 Friday, April 22, 2005 2:51 PM
40LifeBook B Series – Section FourFigure 4-5. Floppy Disk Write ProtectFormatting a floppy disk that already contains data will erase all of the information on the disk.Write ProtectedWrite EnabledB Series.book Page 40 Friday, April 22, 2005 2:51 PM
41User Installable FeaturesFigure 4-6. Installing/Removing PC CardsPC CardsYour LifeBook notebook supports Type I and Type II PC Cards, which can perform a variety of functions. Some available PC Cards:■Fax/data modem cards.■Local area network (LAN) cards.■IDE solid-state disk cards.■SCSI cards.■Other PC Cards that conform to PCMCIA 2.1 or CardBus standards.■Optional SmartCard adapterFor further information, refer to the instructions supplied with your PC Card.INSTALLING PC CARDSPC Cards are installed in the PC Card slot. To install aPC Card, follow these easy steps: (Figure 4-6) 1. See your PC Card manual for specific instructions on the installation of your card. Some PC Cardsmay require your notebook to be Off whileinstalling them.2. Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards.3. Insert your PC Card into the slot, with the product label facing up. 4. Push the card into the slot firmly until it is seated in the opening. REMOVING PC CARDSTo remove a PC Card, follow these easy steps:1. See your PC Card manual for specific instructions on removing your card. Some PC Cards may require your notebook to be in Standby Mode or Off while removing them.2. Push the Eject button until it pops out, and then push it in to eject the card. This will allow you to remove the card.SMART CARD READERAn embedded Smart Card Reader is provided on your LifeBook notebook. Smart Cards are the same size and shape as credit cards, but they contain an integrated microprocessor chip. The chip can hold a variety of information, and provides the user with many possible options, such as allowing them to make secure purchases, pay for phone calls, store security informa-tion, and provide identification and information. In order to use the embedded Smart Card Reader, you must purchase an optional Smart Card holder for instal-lation into an available Type II PC Card slot. Eject ButtonPC Card■Installing or removing a PC Card during your notebook’s shutdown or bootup process may damage the card and/or your notebook.■Do not insert a PC Card into a slot if there is water or any other substance on the card as you may permanently dam-age the card, your notebook, or both. Windows has a shutdown procedure for PC Cards that must be followed before removing a card. (Review your operating system manual for the correct procedure)If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applications and shut down your LifeBook. If the PC Card has an external connector and cable, do not pull the cable when removing the card.B Series.book Page 41 Friday, April 22, 2005 2:51 PM
42LifeBook B Series – Section FourFigure 4-7. Compact Flash Card SlotCompact Flash CardsYour Fujitsu LifeBook notebook supports Compact Flash (CF) cards, which can perform a variety of func-tions. Some available Compact Flash Cards:■Memory cards■Fax/data modem cards■Local area network (LAN) cardsFor further information, refer to the instructions supplied with your PC Card.INSTALLING COMPACT FLASH CARDSCompact Flash Cards are installed in the Compact Flash Card slot. To install a Compact Flash Card, follow these steps: (Figure 4-7) 1. See your Compact Flash Card manual for specific instructions on the installation of your card. Some Compact Flash Cards may require your notebook to be Off while installing them.2. When you receive your LifeBook, there will be a protective plug installed in the slot. Whenever you don’t have a Compact Flash Card installed, be sure to replace the plug to prevent system contamination. To remove the plug, press the Compact Flash Card eject button. (Figure 4-8)Figure 4-8. Removing Compact Flash Slot plug3. When the Compact Flash Slot plug is ejected, remove it from the slot.4. Insert your Compact Flash Card into the slot, with the product label facing up. 5. Push the card into the slot firmly until it is seatedin the opening. You will hear a click and the Eject button will pop away from your notebook.Compact Flash Card Eject ButtonCompact Flash Card SlotCompact Flash Card■Installing or removing a Compact Flash Card during your LifeBook notebook’s shutdown or bootup process may dam-age the card and/or your notebook.■Do not insert a Compact Flash Card into a slot if there is water or any other sub-stance on the card as you may perma-nently damage the card, your LifeBook notebook, or both.Compact Flash Slot PlugCompact Flash Card Eject ButtonB Series.book Page 42 Friday, April 22, 2005 2:51 PM
43User Installable FeaturesREMOVING COMPACT FLASH CARDSTo remove a Compact Flash Card, follow these easy steps:1. See your Compact Flash Card manual for specific instructions on removing your card. Some Compact Flash Cards may require your notebook to be in Suspend Mode or Off while removing them.2. Push the eject button in until it is flush with the notebook. This will push the Compact Flash Card slightly out of the slot allowing you to remove the card.Figure 4-9. Removing a Compact Flash CardWindows has a shutdown procedure for Compact Flash Cards that must be fol-lowed before removing a card. (Please review your operating system manual for the correct procedure). If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applica-tions and shut down your notebook. B Series.book Page 43 Friday, April 22, 2005 2:51 PM
44LifeBook B Series – Section FourMemory Upgrade ModuleYour notebook has been configured with a minimum of 256 MB of high speed DDR2 400 MHz RAM factory installed. In addition to the installed memory, there is a second DIMM slot in which you can install a second module. You can also increase your notebook’s memory capacity by replacing the original module with a higher capacity module (2 GB maximum). The memory upgrade must be a dual-in-line 400 MHz DDR2 module. (To be certain the correct module is used, you should only use Fujitsu memory modules. To order, go to the Fujitsu Web site: http://us.fujitsu.com/computers).INSTALLING A MEMORY MODULE1. Turn off power to your notebook and remove any attached power adapter (AC or auto/airline).2. Make sure that all connector covers are closed.3. Turn the notebook bottom side up.4. Remove the memory upgrade compartment screws, then remove the cover. (Figure 4-10) Figure 4-10. Removing the Memory Module Cover5. Align the new memory upgrade module with the part side up. Align the connector edge of the memory upgrade module with the empty connector slot in the compartment (Figure 4-11). 6. Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is prop-erly in place. (Figure 4-11)8. Replace the memory compartment cover.Figure 4-11. Installing a Memory ModuleREMOVING A MEMORY MODULE1. Turn off power to your notebook and remove any attached power adapter (AC or auto/airline).2. Make sure you are properly grounded.3. Make sure that all connector covers are closed.4. Turn the notebook bottom side up, with the battery toward you.5. Remove the memory upgrade module compartment screws and remove the cover (Figure 4-10).6. Pull the clips sideways away from each side of the memory upgrade module at the same time (Figure 4-12). 7. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the rear of your notebook.8. Store the memory module in a static guarded sleeve.9. Install a new memory module as instructed in “Installing a Memory Upgrade Module”.Figure 4-12. Removing a Memory Upgrade Module10. Replace the cover and the screws.A memory module can be severely damaged by electrostatic discharge (ESD). Be sure you are properly grounded when handling and installing the module.Do not remove any screws from the memory upgrade module compartment except those specifically shown in the directions for installing and removing the memory upgrade module.The memory upgrade module is not something you routinely remove from your notebook. Once it is installed, you should leave it in place unless you want to change system memory capacity.Alignment KeyModule ClipB Series.book Page 44 Friday, April 22, 2005 2:51 PM
45User Installable FeaturesCHECKING THE COMPUTER RECOGNITION OF NEW MEMORY CAPACITYOnce you have changed the system memory capacity, be sure to check that your notebook has recognized the change.You can check the memory capacity by looking at the main menu of the BIOS setup:1. Turn on the power to your notebook.2. Right-click on My Computer.3. Under the General tab, the amount of memory is displayed towards the bottom right of the window. If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. If the module is properly installed and the capacity is still not correctly recognized, see “Troubleshooting” on page 53.B Series.book Page 45 Friday, April 22, 2005 2:51 PM
46LifeBook B Series – Section FourFigure 4-13. Optional Port Replicator rear panel Port Replicator*Ideal for quick connect/disconnect of peripheral devices, the optional Port Replicator extends the functionality of your LifeBook notebook by providing ports to connect a LAN (RJ-45) cable, an external monitor, two USB 2.0 devices, and DC power. The Port Replicator connects to the bottom of your notebook. See “Device Ports” on page 48.PORT REPLICATOR COMPONENTSFollowing is a description of the Port Replicator components. (Figure 4-13)DC Power JackThe DC power jack allows you to plug in the AC adapter to power your notebook and charge the internal Lithium ion battery. The DC power jack is located on the end of the port replicator.USB 2.0 Ports (Qty. 2)Universal Serial Bus (USB) 2.0 ports allow you to connect USB devices. USB 2.0 ports are backward-compatible with USB 1.1 devices.External Monitor PortThe external monitor port allows you to connect an external VGA or SVGA monitor. Note that if a Port Replicator is attached, you must use the external monitor port on the Port Replicator, not the one on your system. LAN (RJ-45) Jack The LAN jack allows you to connect a LAN to the Port Replicator. Note that when the system is attached to the Port Replicator, the LAN Jack on the Port Replicator should be used, not the one on the system.* Optional deviceDocking PortThe docking port connects the Port Replicator to your LifeBook notebook. Port Replicator Release LatchPull the Port Replicator Release latch away from the Port Replicator to remove it from your notebook. ATTACHING PORT REPLICATORTo attach the Port Replicator, align the Port Replicator connector on the bottom of your notebook with the connector on the Port Replicator and push the corners down simultaneously. (Figure 4-14)Figure 4-14. Attaching the Port ReplicatorDETACHING PORT REPLICATORTo detach the Port Replicator:1. Pull the Port Replicator’s release latch away from the Port Replicator to release it from your notebook. (Figure 4-15)USB PortsExternal Monitor PortLAN (RJ-45) JackDC Power JackDocking PortPort Replicator Release LatchB Series.book Page 46 Friday, April 22, 2005 2:51 PM
47User Installable FeaturesFigure 4-15. Unlatching the Port Replicator2. Pull the notebook away from the Port Replicator to detach it from your notebook. (Figure 4-16)Figure 4-16. Removing the Port ReplicatorB Series.book Page 47 Friday, April 22, 2005 2:51 PM
48LifeBook B Series – Section FourDevice PortsYour LifeBook notebook and the optional Port Repli-cator come equipped with multiple ports to which you can connect an external device including: disk drives, keyboards, modems, printers, etc. MODEM (RJ-11) JACKThe modem (RJ-11) jack is used for an internal modem. To connect the telephone cable follow these easy steps: See “LifeBook notebook left-side panel” on page 9.1. Align the connector with the jack opening.2. Push the connector into the jack until it is seated.3. Plug the other end of the telephone cable into atelephone outlet.INTERNAL LAN (RJ-45) JACKThe internal LAN (RJ-45) jack is used for an internalFast Ethernet (10/100 /1000 Base-T/Tx) connection. If your notebook has been configured with internal LANcapability you will need to configure your notebookto work with your particular network. (Please refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these steps: See “LifeBook notebook rear panel” on page 12.1. Align the connector with the jack opening.2. Push the connector into the jack until it is seated.3. Plug the other end of the cable into a LAN outlet.DOCKING PORTThe docking port is used for the connection of your Life-Book notebook to an optional port replicator. In order to connect your notebook to one of these devices follow the instructions that came with your docking port. UNIVERSAL SERIAL BUS 2.0 PORTSThe two Universal Serial Bus (USB) 2.0 ports allow you to connect USB devices such as external floppy disk drives, game pads, pointing devices, keyboards and/or speakers. In order to connect a USB device follow these easy steps: See “LifeBook notebook right-side panel” on page 10.1. Align the connector with the port opening.2. Push the connector into the port until it is seated.MICROPHONE JACKThe microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your notebook. In order to connect a microphone follow these easy steps: See “Life-Book notebook left-side panel” on page 9.1. Align the connector with the port opening.2. Push the connector into the port until it is seated.HEADPHONE JACKThe stereo headphone jack allows you to connect stereo headphones or powered external speakers to your note-book. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: See “LifeBook notebook left-side panel” on page 9.1. Align the connector with the port opening.2. Push the connector into the port until it is seated.■The internal modem is designed to the ITU V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600bps at upload. ■The internal modem on all LifeBook notebooks from Fujitsu Computer Systems Corporation are certified for use in the United States and Canada.■Depending upon the configuration of your system, your LifeBook notebook may have either a LAN jack or an IEEE 1394 jack.The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook notebook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.Note that the optional Port Replicator is designed to cover the LAN jack located on the system. This design ensures that the LAN jack on the Port Replicator is the only one used when the Port Replicator is installed.If you plug headphones into the headphone jack, the built-in stereo speakers will be disabled.B Series.book Page 48 Friday, April 22, 2005 2:51 PM
49User Installable FeaturesEXTERNAL MONITOR PORTThe external monitor port allows you to connect an external monitor. In order to connect an external monitor follow these easy steps: See “LifeBook notebook rear panel” on page 12.1. Remove the cover from the port opening, if present.2. Align the connector with the port opening.3. Push the connector into the port until it is seated.4. Tighten the two hold-down screws, located oneach end of the connector. When a Port Replicator is attached and an external monitor is plugged in, pressing the [Fn] + [F10] keys allows you to change your selection of where to send your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external monitor only, finally moving to both the built-in display panel and an external monitor.B Series.book Page 49 Friday, April 22, 2005 2:51 PM
50LifeBook B Series – Section FourB Series.book Page 50 Friday, April 22, 2005 2:51 PM
515TroubleshootingB Series.book Page 51 Friday, April 22, 2005 2:51 PM
52LifeBook B SeriesB Series.book Page 52 Friday, April 22, 2005 2:51 PM
53TroubleshootingTroubleshootingYour LifeBook notebook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.IDENTIFYING THE PROBLEMIf you encounter a problem that you are having diffi-culty in solving, go through the following procedure before pursuing further troubleshooting:1. Turn off your LifeBook notebook.2. Make sure the AC adapter is plugged into your note-book and to an active AC power source.3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.5. Turn on your notebook. Make sure it has been off at least 10 seconds before you turn it on.6. Go through the boot sequence.7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information. 8. If you have tried the solutions suggested in the Trou-bleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu Fax: 408-764-2724 E-mail: 8fujitsu@us.fujitsu.comWeb site: http://www.computers.us.fujitsu.com/support.Before you place the call, you should have the following information ready so that the customer support repre-sentative can provide you with the fastest possible solu-tion:■Product name■Product configuration number■Product serial number■Purchase date■Conditions under which the problem occurred■Any error messages that have occurred■Type of device connected, if anySee the Configuration Label on the bottom of yourLifeBook notebook for configuration and serial numbers. (See figure 2-8 on page 11 for location)SPECIFIC PROBLEMSUsing the Troubleshooting TableWhen you have problems with your notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you diffi-culty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.■If you keep notes about what you have tried, your support representative may be able to help you more quickly by giv-ing additional suggestions over the phone.■Do not return a failed LifeBook note-book to your supplier until you have talked to a support representative.B Series.book Page 53 Friday, April 22, 2005 2:51 PM
54LifeBook B Series – Section FiveTROUBLESHOOTING TABLEProblem PageAudio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 54Docking Problems . . . . . . . . . . . . . . . . . . . . . . . . page 54Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 54Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 54Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 55Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 55Problem PageModem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 55USB Device Problems . . . . . . . . . . . . . . . . . . . . . page 56PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 56Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 56Shutdown and Startup Problems . . . . . . . . . . . . page 58Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 58Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 60Problem Possible Cause Possible SolutionsAudio ProblemsThere is no sound coming from the built-in speakers.The volume is turned too low. Adjust the volume control on your notebook.The software volume control is set too low.Adjust the sound volume control settings in your software, operating system and applications.Headphones are plugged into your notebook.Plugging in headphones disables the built-in speakers, remove the headphones.BIOS audio settingsare incorrect.Set the BIOS setup utility to the default values within the Advanced/Miscellaneous Configurations menu. See “BIOS Setup Utility” on page 29.Software driver is not config-ured correctly.Refer to your application and operating system documentation for help.Sound could have been muted with function keys.Press [F3] while holding the [Fn] key to toggle the sound on and off.Port Replicator ProblemsLifeBook notebook does not turn on when installed in optional Port ReplicatorPort Replicator AC adapter is not plugged in. Provide power to the Port Replicator.Notebook is not properly seated in the Port Replicator.Remove and re-dock your notebook.Floppy Disk Drive ProblemsYou cannot access your floppy disk.You tried to write to a write protected floppy disk.Eject the floppy disk and set it to write enable. See “Preparing a Disk for Use” on page 39.Floppy disk is not loaded correctly.Eject floppy disk, check orientation and re-insert. See “Ejecting a Disk” on page 39.The floppy disk drive may not be properly installed.Remove and re-install your floppy disk drive. Security is set to protect access to floppy disk data.Verify your password and security settings.The USB floppy disk drive is not selected in the BIOS.Verify that USB Support is enabled in the BIOS Advanced menu. See “BIOS Setup Utility” on page 29.Hard Drive ProblemsYou cannot access your hard drive.The setup utility is incorrectly set for your hard drive.Revise BIOS settings to set both Primary Masterand Primary Slave correctly. See “BIOS Setup Utility” on page 29.B Series.book Page 54 Friday, April 22, 2005 2:51 PM

Navigation menu