Fujitsu Client Computing WB0038 LIFEBOOK T SERIES with WM3945ABG 11ABG WLAN & BT User Manual T Series

Fujitsu Limited LIFEBOOK T SERIES with WM3945ABG 11ABG WLAN & BT T Series

App I2 User Manual Part 2

65TroubleshootingYour Tablet PC appears to change setup parameters when you start it.BIOS setup changes were not saved when you made them and exited the BIOS setup utility returning it to previous settings.Make sure you select Save Changes And Exit when exiting the BIOS setup utility.The BIOS CMOS back-up battery has failed.Contact your support representative for repairs. This is not a user-serviceable part.Video ProblemsThe built-in display is blank when you turn on your Tablet PC.The angle of the display and the brightness settings are not adequate for your lighting conditions.Move the display and the brightness control until you have adequate visibility.The optional Port Replicator is attached, an external monitor is plugged in, and the Tablet PC is set for an external monitor only.Pressing [F10] while holding down the [Fn] key allows you to change your selection of where tosend your display video. Each time you press the combination of keys you will step to the nextchoice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.The power management timeouts may be set for very short intervals and you failed to notice the display come onand go off again.Press any button the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standby mode, Auto Suspend or Video Timeout)The Tablet PC turned on with a series of beeps and your built-in display is blank.Power On Self Test (POST)has detected a failure which does not allow the displayto operate. Contact your support representative.Your system display won’t turn on when the system is turned on or when the system has resumed.The system may be password-protected.Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.The display goes blank by itself after you have been using it.The Tablet PC has gone into Video Timeout, Standby Mode, or Hibernate Mode because you have not used it for a period of time.Press a button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. See “BIOS Setup Utility” on page 36.The power management time-outs may be set for very short intervals and you failed to notice the display come onand go off again.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout)The display does not close. A foreign object, such as a paper clip, is stuck between the display and the keyboard.Remove all foreign objects from the keyboard.Problem Possible Cause Possible SolutionsT Series.book Page 65 Thursday, July 14, 2005 2:24 PM
66LifeBook T Series Tablet PC - Section FiveThe display has bright or dark spots.If the spots are very tiny and few in number, this is normal for a large LCD display.This is normal; do nothing.If the spots are numerous or large enough to interfere with your operation needs.The display needs technical diagnosis; contact your support representative.The application display uses only a portion of your screen and is surrounded by a dark frame.You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compres-sion is enabled.When compensation is disabled, a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution will result. You can fill the screen but have less resolution by changing your compensation setting. (See the Video Features submenu, located within the Advanced menu of the BIOS. See “BIOS Setup Utility” on page 36.You have connected an external monitor and it does not display any information.Your BIOS setup is not set to enable your external monitor.Try toggling the video destination by pressing [Fn] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. See “BIOS Setup Utility” on page 36.Your external monitor is not properly installed. Reinstall your device. See “External Video Port” on page 55.Your operating system soft-ware is not set up with the correct software driver forthat device.Check your device and operating systemdocumentation and activate the proper driver.You have connected an external monitor and it does not come on.Your external monitor may not be compatible with your Tablet PC.See your monitor documentation and the External Monitor Support portions of the Specifications section. See “Specifications” on page 79.Miscellaneous ProblemsAn error message is displayed on the screen during the operation of an application.Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.Problem Possible Cause Possible SolutionsT Series.book Page 66 Thursday, July 14, 2005 2:24 PM
67TroubleshootingPOWER ON SELF TEST MESSAGESThe following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes successfully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)*Extended RAM Failed at offset: nnnn Extended memory not working or not configured prop-erly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is prop-erly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.nnnn Extended RAM Passed Where nnnn is the amount of memory in kilobytes successfully tested.*Failing Bits: nnnn The hex number nnnnThis is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4) The fixed disk is not working or not configured prop-erly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.*Invalid NVRAM media typeProblem with NVRAM access. In the unlikely case that you see this message you may have some display prob-lems. You can continue operating but should contact your support representative for more information.*Keyboard controller error The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.*Keyboard error Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able touse an external keyboard until then. Contact your support representative.*Keyboard error nn BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted and your system may have to be re-installed from your back up media.*Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays “????”. This is apotentially data destroying failure. Contact yoursupport representative.*Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays “????”. This is apotentially data destroying failure. Contact yoursupport representative.*Press <F1> to resume, <F2> to SETUP Displayed after any recoverable error message. Pressthe [F1] key to continue the boot process or the [F2]key to enter Setup and change any settings.*Previous boot incomplete – Default configuration used Previous Power On Self Test did not complete success-fully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power and contact your support representative.T Series.book Page 67 Thursday, July 14, 2005 2:24 PM
68LifeBook T Series Tablet PC - Section Five*Real time clock error Real-time clock fails BIOS test. May require board repair. Contact your support representative.*Shadow RAM Failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corruption if you continue. Contact your support repre-sentative.nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested.*System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your Tablet PC.System BIOS shadowed System BIOS copied to shadow RAM.*System CMOS checksum bad – run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.*System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.nnnn System RAM PassedWhere nnnn is the amount of system memory inkilobytes successfully tested.*System timer error The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.Video BIOS shadowed Video BIOS successfully copied to shadow RAM.MODEM RESULT CODESThe operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are:■OK■NO CARRIER■NO DIALTONE■CONNECT 53000 (Connection complete at 53,000 bps.)■ERROR■FAX■RING (This means an incoming call.)■BUSY■NO ANSWERWhen using the internal modem with applications that are not factory installed refer to the application documentation.T Series.book Page 68 Thursday, July 14, 2005 2:24 PM
69TroubleshootingRestoring Your Pre-installed SoftwareThe Drivers and Applications Restore (DAR) DVD contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your Tablet PC configuration for use as documented below.RE-INSTALLING INDIVIDUAL DRIVERS AND APPLICATIONS The Drivers and Applications CD can be used to selec-tively re-install drivers and/or applications that may have been un-installed or corrupted. To re-install drivers and/or applications:1. Boot up the system and insert the DAR CD after Windows has started. A Fujitsu Installer screen is displayed after the CD is inserted.2. After reading the License Agreement, click [I agree].3. A window will appear containing a list of applica-tions, drivers, and utilities that you can install from the Drivers and Applications CD.4. In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately.5. Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed.6. After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system. RESTORING THE FACTORY IMAGEThe Restore Disc that came with your system contains two utilities:■The Recovery utility allows you to restore the original contents of the C: drive.■The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use Hard Disk Data Delete unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.BOOT Priority ChangeBefore restoring an image, you must first verify that your system is set up to boot from the DVD drive. To verify/change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps:In order to install applications and/or drivers from the DAR DVD, you will need access to a DVD drive. If you do not have a built-in modular DVD drive, you will need to connect an external DVD drive to your system.If you have access to the internet, visit the Fujitsu Support web site at http://www.computers.us.fujitsu.com/support to check for the most current information, drivers and hints on how to perform recovery and system updates.There may be certain free third-party applications pre-installed on your system that are not on the DAR CD. The latest versions of the applications can be downloaded from the third-party’s website.The components listed are color-coded in terms of their install status. Blue indicates that the component can be installed. Green indicates that the component needs to be installed separately. Grey indicates a component that is already installed; grey items can be reinstalled, but prior to installation you will receive a reminder that the component is already installed and may need to be uninstalled prior to reinstallation.• The use of this disc requires that you have a device capable of reading DVDs attached to your system. If you do not have a built-in DVD player, you will need to attach an external player. For more information on available external devices, visit our Web site at: us.fujitsu.com/computers. • This disc can only be used with the system with which it was purchased.T Series.book Page 69 Thursday, July 14, 2005 2:24 PM
70LifeBook T Series Tablet PC - Section Five1. Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.2. Using the arrow keys, go to the Boot menu.3. Arrow down to the Boot Device Priority submenu. Press [Enter].4. If “Optical Media Drive” or “CD-ROM Drive” is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.). Note that the BIOS for some systems will indicate “CD-ROM Drive”, even when a DVD drive is connected.5. If you have an external DVD drive connected, proceed to the next step; otherwise, proceed to step 7.6. If you have an external DVD drive connected:• Select the Advanced menu in the BIOS window.• Scroll down to the USB Features submenu and press the Enter key to open it.• If Legacy USB Support is disabled, press the space bar to enable it.• Scroll down to SCSI SubClass Support and press the space bar to enable it. 7. Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.After you have changed the boot priority, you can restore a backup image when you are booting up.Procedure1. Turn on the power to your system.2. Ensure that you have a device that can read DVDs either installed in your system or attached exter-nally to it.3. Insert the Restore Disc into the drive tray.4. Reboot your system.5. After the system reboots, follow the instructions that appear to either restore your system image or erase all data from your hard disk.T Series.book Page 70 Thursday, July 14, 2005 2:24 PM
716Care and MaintenanceT Series.book Page 71 Thursday, July 14, 2005 2:24 PM
72LifeBook T Series Tablet PC - Section SixT Series.book Page 72 Thursday, July 14, 2005 2:24 PM
73Care and MaintenanceCare and MaintenanceIf you use your LifeBook T Series Tablet PC carefully, you will increase its life and reliability. This section provides some tips for looking after the Tablet PC and its devices.LIFEBOOK T SERIES TABLET PCCaring for your Tablet PC■Your Tablet PC is a durable but sensitive electronic device. Treat it with care.■Make a habit of transporting it in a suitable carrying case.■Do not attempt to service the computer yourself. Any unauthorized service performed on the computer will void the warranty.■To protect your computer from damage and to opti-mize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used. ■Do not operate the computer in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.■ Always follow installation instructions closely.■Keep it away from food and beverages.■If you accidentally spill liquid on your Tablet PC:1. Turn it off.2. Position it so that the liquid can run out.3. Let it dry out for 24 hours, or longer if needed.4. If your Tablet PC will not boot after it has dried out, call your support representative.■Do not use your Tablet PC in a wet environment (near a bathtub, swimming pool).■Always use the AC adapter and batteries that are approved for your Tablet PC.■Avoid exposure to sand, dust and other environmental hazards.■Do not expose your Tablet PC to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your Tablet PC.■Keep the covers closed on the connectors and slots when they are not in use.■Do not put heavy or sharp objects on the computer.■If you are carrying your Tablet PC in a briefcase, or any other carrying case, make sure that there are no objects in the case pressing on the lid.■Do not drop your Tablet PC.■Do not touch the screen with any sharp objects. Cleaning your Tablet PC■Always disconnect the power plug. (Pull the plug, not the cord.)■Clean your Tablet PC with a damp, lint-free cloth. Do not use abrasives or solvents.■Use a soft cloth to remove dust from the screen. Never use glass cleaners.Storing your Tablet PC■If storing your Tablet PC for a month or longer, turn the Tablet PC off, fully charge the battery, then remove and store all Lithium ion batteries.■Store your Tablet PC and batteries separately. If you store your Tablet PC with a battery installed, the bat-tery will discharge, and battery life will be reduced. In addition, a faulty battery might damage the Tablet PC.■Store your Tablet PC in a cool, dry location. Temperatures should remain between 13º F (-25º C) and 140º F (60º C).Traveling with your Tablet PC■Do not transport your Tablet PC while it is turned on. ■Do not check your Tablet PC as baggage. Carry it with you.■When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine. Electrical equipment may be hazardous if misused. Operations of this product or similar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.T Series.book Page 73 Thursday, July 14, 2005 2:24 PM
74LifeBook T Series Tablet PC - Section Six■Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which adapter you'll need or ask your travel agent.Figure 6-1. Outlet typesKEYBOARDCaring for your KeyboardThe keyboard of your computer is a very sensitive instrument. It is made up of many switches that are activated when you press on the keys. The keyboard is a major component of the heat dissipation system in a Tablet PC. Due to heat and size considerations the keyboard is not sealed. Because the keys are so close together, it is not easy for the user to see when liquids have fallen onto the circuitry below the keys. Attempting to clean the keyboard with a spray on cleaner or rag soaked with cleaner the liquid can drip onto the circuitry sight unseen. Once the liquid seeps between the layers of circuitry, it can cause corrosion or other damage to the circuits. This can result in keys which no longer operate, or which, when pressed, record the wrong characters and other similar failures.There is no repair for this problem other than replace-ment. The solution is to become aware of the issue and take appropriate steps to protect your keyboard. To clean the keyboard, use a rag dampened slightly with cleaning solution. Use extreme care to prevent liquid from dripping between the keys. Spraying directly on the keys should be avoided. The spray should be applied first to the cloth, and then the cloth wiped over the keys.BATTERIESCaring for your Batteries■Always handle batteries carefully.■Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.■Do not drop, puncture, disassemble, mutilate or incin-erate the battery.■Recharge batteries only as described in this manual and only in ventilated areas.■Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.■Do not leave a battery in storage for longer than six months without recharging it.Increasing Battery Life■Keep brightness to the lowest comfortable level.■Set the power management for maximum battery life.■Put your Tablet PC in Standby mode when it is turned on and you are not actually using it.■Limit your CD-ROM access.■Disable the Windows CD auto insert function.■Always use fully charged batteries.■Eject PCMCIA cards when not in use.OPTIONAL FLOPPY DISK DRIVE AND FLOPPY DISKSCaring for your Floppy Disks■Avoid using floppy disks in damp and dusty locations.■Never store a floppy disk near a magnet or magnetic field.■Do not use a pencil or an eraser on a disk or disk label.■Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10º C) and 125º F (52º C).■Do not touch the exposed part of the disk behind the metal shutter.Caring for your Optional Floppy Disk Drive■To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.■Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe Outlet Type LocationUnited States, Canada, Mexico, parts of Latin America, Japan, Korea, the Philippines, TaiwanRussia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South AsiaUnited Kingdom, Ireland, Malaysia, Singapore, parts of AfricaChina, Australia, New Zealand T Series.book Page 74 Thursday, July 14, 2005 2:24 PM
75Care and Maintenancetemperature changes. Store at temperatures between 50º F (10º C) and 125º F (52º C).■Keep the floppy disk drive out of direct sunlight and away from heating equipment.■Avoid storing the floppy disk drive in locations subject to shock and vibration.■Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy disk drive or disk.■Never disassemble or dismantle your floppy disk drive.OPTIONAL OPTICAL DRIVE AND DISCSCaring for your discsCDs and DVD discs are precision devices and will func-tion reliably if given reasonable care.■Always store your discs in their case when not in use.■Always handle discs by the edges and avoid touching the surface.■Avoid storing any discs in extreme temperatures.■Do not bend discs or set heavy objects on them.■Do not spill liquids on discs.■Do not scratch discs.■Do not put a label on discs.■Do not get dust on discs.■Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.■If a disc is subjected to a sudden change in tempera-ture, cold to warm condensation may form on the sur-face. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry discs.■If a disc is dirty, use only a disc cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.Caring for your Optional Optical DriveYour optical drive is durable but you must treat it with care. Please pay attention to the following points:■The drive rotates the compact disk at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.■Avoid using or storing the drive where it will be exposed to extreme temperatures.■Avoid using or storing the drive where it is damp or dusty.■Use of a commercially-available lens cleaner kit is recommended to maintain the drive lens. ■Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.■Avoid using or storing the drive where it will be subjected to shock or vibration.■Do not disassemble or dismantle the optical drive.PC CARDSCaring for your PC Card Slots PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Cards provides specific information for caring for the cards. When you don’t have a PC Card inserted in your system, you should be sure to insert the PC Card slot inserts that came with your system. These will help to keep dust and dirt out of your system.T Series.book Page 75 Thursday, July 14, 2005 2:24 PM
76LifeBook T Series Tablet PC - Section SixT Series.book Page 76 Thursday, July 14, 2005 2:24 PM
777SpecificationsT Series.book Page 77 Thursday, July 14, 2005 2:24 PM
78LifeBook T Series Tablet PC - Section SevenT Series.book Page 78 Thursday, July 14, 2005 2:24 PM
79SpecificationsSpecificationsThis section provides the hardware and environmental specifications for your LifeBook T Series Tablet PC. Specifications of particular configurations will vary.CONFIGURATION LABELYour LifeBook T Series Tablet PC has a configuration label located on the bottom. (See figure 2-8 on page 16 for location). This label contains specific information regarding the options you’ve chosen for your Tablet PC. Following is an example label and information on how to read your own configuration label.Figure 7-1. Configuration LabelLifeBook T Series Tablet PC SpecificationsThe specifications for your particular model may vary. To determine the specifications for your system, please visit our Web site at: us.fujitsu.com/computers.Physical SpecificationsDimensions 11.54” w x 9.61” d x 1.38" / 1.48" (293 mm x 244 mm x 35 / 37.5 mm)Processing SpecificationsCPU/Speed Intel® Pentium® M Processor 740/760 Chip set Intel 915GM - 533 MHzMemory/Storage SpecificationsMain RAM • 256 MB SDRAM (DDR2 533 MHz)• 200-pin SO DIMM slots x 2256 MB, 512 MB, and 1.0 GB modules available, with a system maximum of 2.0 GB.L1 cache (CPU)64 KB on-die L2 cache 2 MB on-die BIOS ROM 1 MB (Boot Block Type Flash ROM)T4210, PM 740, 12.1 XGA, XPTE, 40G, 256MConfiguration P/N: AE2XXXXXXXXXXXXFPC P/N: FPCXXXXXXModelProcessorScreenSizeOperatingSystemHard Drive MemoryPart NumberConfiguration IDHard disk drive• 2.5” HDD• Minimum 40 GB IDE (5400 rpm)Also available:60 GB (5400 rpm)80 GB (5400 rpm)• SATA 150• Shock-mounted• SMART SupportDisplay SpecificationsDisplay 12.1" TFT XGA (1024 x 768), 16M colors:• Color LCD• Active Digitizer• 32-bit color• External monitor support: VGA (1024 x 768 maximum)• Dot pitch: 0.240 x 0.240 mm• Viewing Angle: Horizontal: 90 degrees (max.) Vertical: 90 degrees (max.)• Optional Indoor/Outdoor ViewabilityOptional 12.1" TFT SXGA+ (1400 x 1050), 16M colors:• Color LCD• Transmissive indoor display• Active Digitizer• 32-bit color• External monitor support: VGA (1024 x 768 maximum)• Dot pitch: 0.175 x 0.175 mm• Standard Viewing AngleVRAM Intel® Graphics Media Accelerator 915 video graphics. Up to 128 MB shared video memory using Dynamic Video Memory Technology (DVMT)Interface SpecificationsIntegrated Interfaces• Modem (RJ-11)• LAN (RJ-45)• USB 2.0 x 2•DC-In•IrDA• IEEE1394• Analog RGB, Mini D-SUB 15-pin connector for external VGA monitor• Docking connectorLifeBook T Series Tablet PC Specifications (Continued)T Series.book Page 79 Thursday, July 14, 2005 2:24 PM
80LifeBook T Series Tablet PC - Section SevenInterfaceson Optional Port Replicator • DC Power• LAN (RJ-45)• 15-pin D-SUB connector for external VGA monitor• DVI-D for external monitor• USB 2.0 x 4•Line Out• Docking PortPC Card Slots• One Type I or Type II• PCMCIA CardBus version 3.0SD/Memory Stick SlotOne slot for SD/Memory Stick cardSmart Card SlotDedicated slot for SmartCardModular Bay Devices One of the following devices is pre-installed:• Dual-Layer Multi-Format DVD Writer: 8x DVD-ROM, 24x CD-R, 10x CD-RW, 24x CD-ROM, 8x DVD-R, 4x DVD-RW, 8x DVD+R, 4x DVD+RW, 3x DVD-RAM•DVD-ROM Drive: 8x DVD-ROM• DVD/CD-RW Combo Drive: 8x DVD-ROM, 24x CD-R, 24x CD-RW, 24x CD-ROM• Modular Bay Battery• Weight SaverInfrared • System IR Port• IrDA version 1.1 (FIR, 4 Mbps)User Interface support• Keyboard Pitch: 19 mm, Stroke: 3 mm• TouchPad pointing device with scroll button or optional fingerprint sensor• Active digitizer with pen input• On-screen keyboardAudio • Sigmatel STAC9753A• Dual internal microphone array with background noise cancellation• Stereo speaker x 2• Mono microphone and stereo headphone jacks• 26 adjustable audio levelsLifeBook T Series Tablet PC Specifications (Continued)User Controls• Programmable Application Buttons, each with primary and secondary functions (default applications: Microsoft Journal and Calculator)• Security button support• Trusted Platform Module (TPM) support (on some models)• Suspend/Resume buttonStatus Indicators (LCDs)• Power•Charge/DC-In• Battery charging (x 2)• Battery level (x 2)• Wireless LAN/Bluetooth Switch• Optical drive• Hard disk drive•Caps Lock•Num Lock• Scroll Lock•SecurityPower SpecificationsMain Battery • 6-cell • Removable, Lithium ion• 10.8 V @5200 mAh, max. 56 WHr• Warm-swappableOptional Bay Battery•6-cell• Removable, Lithium ion• 10.8V @ 3800 mAh, max. 41.0 WHrBridge Battery• 6-cell NiMH, 35 mAh• Life (with Suspend-to-RAM on bridge battery only): 5 minutes from full chargeAC Adapter Autosensing 100 - 240V, supplying 19 VDC, with a current of 3.15 AEnvironmental SpecificationsTemperature Operating: 41o to 95o F (5o to 35o C) Non-operating: 5o to 140o F (-15o to 60o C) Humidity Operating: 20 to 80% non-condensingNon-operating: 8 to 85% non-condensingLifeBook T Series Tablet PC Specifications (Continued) T Series.book Page 80 Thursday, July 14, 2005 2:24 PM
81SpecificationsAgency Approval SpecificationsEmissions• EN55022 (CISPR22) Class B • FCC 15, Class B• FCC 15C, 15.247• ICES-003• Canada RSS-210• ETSI EN 300 328-1 V1.3.1 : 2001• ETSI EN 300 328-2 V1.2.1 : 2001_12• ETSI EN 301 498-17 V1.2.1 : 2002• ETSI EN 301 498-1 V1.4.1 : 2002Immunity • EN55024 (1998)Safety • UL and cUL Listed, UL 60950Telecom • FCC Part 68• IC CS-03Additional SpecificationsOperating systems Microsoft® Windows® XP Tablet PC Edition 2005LifeBook T Series Tablet PC Specifications (Continued)T Series.book Page 81 Thursday, July 14, 2005 2:24 PM
82LifeBook T Series Tablet PC - Section SevenRegulatory InformationFCC NOTICESNotice to Users of Radios and TelevisionThese limits are designed to provide reasonable protec-tion against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic-ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet that is on a different circuit than the receiver.• Consult the dealer or an experienced radio/TVtechnician for help.Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Notice to Users of the US Telephone NetworkThis equipment contains an internal modem (Fujitsu Media Devices, MBH 7MD33) that complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.This equipment is designed to be connected to the tele-phone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.The ringer equivalent number (REN) of this equipment is 0.1B as shown on the label. The REN is used to deter-mine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local tele-phone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facili-ties, equipment, operations or procedures that could effect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to main-tain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commis-sion or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equip-ment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such busi-ness, other entity, or individual.Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipmentT Series.book Page 82 Thursday, July 14, 2005 2:24 PM
83Regulatory InformationDOC (INDUSTRY CANADA) NOTICESNotice to Users of Radios and TelevisionThis Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.Notice to Users of the Canadian Telephone Network NOTICE: This equipment (Fujitsu Media Devices modem, MBH 7MD33) meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number (4061A-8687) signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certifica-tion standards does not prevent service degradation in some situations.Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecom-munication company cause to request the user to disconnect the equipment from the telephone line.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equiva-lence Numbers of all the devices does not exceed five.Avis Aux Utilisateurs Du Réseau Téléphonique CanadienAVIS: Le présent matériel est conforme aux spécifica-tions techniques d’Industrie Canada applicables au matériel terminal. Cette conformité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement (4061A-8687), signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifica-tions techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel. Avant de connecter cet équipement à une ligne télépho-nique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécom-munications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur décon-necte l’équipement de la ligne téléphonique.AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.0. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équiva-lence de la sonnerie de tous les dispositifs n’excède pas 5.For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appro-priate electric inspection authority or elec-trician. This may be particularly important in rural areas.Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du ser-vice d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont con-nectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connex-ions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales.T Series.book Page 83 Thursday, July 14, 2005 2:24 PM
84LifeBook T Series Tablet PC - Section SevenT Series.book Page 84 Thursday, July 14, 2005 2:24 PM
858GlossaryT Series.book Page 85 Thursday, July 14, 2005 2:24 PM
86LifeBook T Series Tablet PC - Section EightT Series.book Page 86 Thursday, July 14, 2005 2:24 PM
87GlossaryGlossaryAC AdapterA device which converts the AC voltage from a wall outlet to the DC voltage needed to power your Tablet PC.ACPIAdvanced Configuration and Power InterfaceActive-Matrix DisplayA type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.AdHocA designation for wireless LAN network configuration. It indicates a form of communication limited to those personal computers which have wireless LAN function. .ADSLAsymmetric Digital Subscriber LineTechnology for transporting high bit-rate services over ordinary phone lines.Auto/Airline AdapterA device which converts the DC voltage from an auto-mobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your Tablet PC.BIOSBasic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your Tablet PC when you turn it on until it loads your installed operating system from disk. Infor-mation from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.BitAn abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).bpsAn abbreviation for bits per second. Used to describe data transfer rates.BootTo start-up a computer and load its operating system from disk, ROM or other storage media into RAM.BusAn electrical circuit which passes data between the CPU and the sub-assemblies inside your Tablet PC.Byte8 bits of parallel binary information.Cache MemoryA block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.CardBusA faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.CD-ROMCompact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.ChannelThe frequency band of wireless LAN to be used in communications over wireless LAN or at the access point.CMOS RAMComplementary metal oxide semiconductor random access memory. This is a technology for manufacturing random access memory which requires very low levels of power to operate.CommandAn instruction which you give your operating system. Example: run a particular application or format a floppy disk.ConfigurationThe combination of hardware and software that makes up your system and how it is allocated for use.CRTCathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam.DataThe information a system stores and processes.DCDirect current. A voltage or current that does not fluctuate periodically with time.Default ValueA pre programmed value to be used if you fail to set your own.T Series.book Page 87 Thursday, July 14, 2005 2:24 PM
88LifeBook T Series Tablet PC - Section EightDHCP Dynamic Host Configuration ProtocolA protocol used for automatically fetching communica-tion parameters such as IP addresses. The side which assigns IP address is called DHCP server and the side that is assigned it is called DHCP client.DIMMDual-in-line memory module.DiskA spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.Disk DriveThe hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.DisketteA floppy disk in a hard housing with a shutter.DMADirect Memory AccessSpecial circuitry for memory to memory transfers of data which do not require CPU action.DMIDesktop Management Interface A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals.DNS Domain Name SystemA function that controls the correspondence of IP addresses assigned to a computer with the name. Even for those computers whose IP addresses are unknown, if their names are known, it is possible to communicate with them.DOSDisk Operating System (MS-DOS is a Microsoft Disk Operating System).DriverA computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.ECPExtended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices.Encryption Key (Network Key)Key information used to encode data for data transfer.This device uses the same encryption key to encode and decode the data, and the identical encryption key is required between the sender and receiver.ESDElectro-Static Discharge. The sudden discharge of elec-tricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.Extended MemoryAll memory more than the 640KB recognized by MS-DOS as system memory.FCCFederal Communication Commission.Floppy DiskA spinning platter of magnetic data storage media which is highly flexible.GBGigabyte.Hard driveA spinning platter of magnetic data storage media where the platter is very stiff.I/OInput/Output. Data entering and leaving your Tablet PC in electronic form.I/O PortThe connector and associated control circuits for data entering and leaving your Tablet PC in electronic form.IDEIntelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.IEEE 1394Industry standard that allows you to connect between your Tablet PC and a peripheral device such as a digital camera. Also known as “Firewire” or “iLINK”.T Series.book Page 88 Thursday, July 14, 2005 2:24 PM
89GlossaryIEEE802.11aOne of the wireless LAN standards prescribed by the 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Elec-tronic Engineers). This standard allows communica-tions at the maximum speed of 54 Mbps by using a 5 GHz band which can freely be used without radio communication license. IEEE802.11bOne of the wireless LAN standards prescribed by 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Elec-tronic Engineers). It allows communications at the maximum speed of 11 Mbps by a band of 2.4 GHz (ISM band) which can freely be used without radio communi-cation license. IEEE802.11gOne of the wireless LAN standards prescribed by 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Elec-tronic Engineers). It allows communications at the maximum speed of 54 Mbps by a band of 2.4 GHz (ISM band) which can freely be used without radio communi-cation license. InfraredLight just beyond the red portion of the visible light spectrum which is invisible to humans.InfrastructureA designation of Wireless LAN network configurations. It indicates a form of communication using an Access Point. IP AddressAn address used for computers to communicate in the TCP/IP environment.Current IPv4 (version 4) uses four values in the range between 1 and 255. (Example: 192.168.100.123).There are two types of IP address: global address and private address.The global address is an only address in the world. It is controlled by JPNIC (Japan Network Information Center). A private address is an only address in the closed network.IRAn abbreviation for infrared.IrDAInfrared Data Association. An organization which produces standards for communication using infrared as the carrier.IRQInterrupt RequestAn acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.KB Kilobyte.LANLocal Area NetworkAn interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.LCDLiquid Crystal DisplayA type of display which makes images by controlling the orientation of crystals in a crystalline liquid.Lithium ion BatteryA type of rechargeable battery which has a high power-time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.LPT PortLine Printer Port. A way of referring to parallel interface ports because historically line printers were the first and latter the most common device connected to parallel ports.MAC Address Media Access Control AddressA unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards. For Ethernet, frames are sent and received based on this address.MBMegabyte.Megahertz1,000,000 cycles per second.MemoryA repository for data and applications which is readily accessible to your Tablet PC’s CPU.MHzMegahertz.T Series.book Page 89 Thursday, July 14, 2005 2:24 PM
90LifeBook T Series Tablet PC - Section EightMIDIMusical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers.ModemA contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.MonauralA system using one channel to process sound from all sources.MPU-401A standard for MIDI interfaces and connectors.MTUMaximum Transmission UnitThe maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large.Network authenticationThe method of authentication performed by wireless LAN clients to connect with the access point. There are two types: open system authentication and shared key authentication. The type of authentication must be set to each client and also coincide with the setting of access point with which to communicate. Network authentica-tion is sometimes called authentication mode.Network keyData that is used for encrypting data in data communi-cation. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.Network name (SSID: Security Set Identifier)When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.NTSCNational TV Standards Commission. The standard for TV broadcast and reception for the USA.Open system authenticationOne of network authentication types for wireless LAN. Since there is no check of network key upon authentica-tion, clients can connect to the access point without submitting correct network keys. However, in case of actual communications, the same network key must be set. Open system authentication is sometimes called Open key authentication.Operating SystemA group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of micro-processor in order to produce the desired results from that particular equipment.PartitionA block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.PCIPeripheral Component Interconnect Self-configuring PC local bus. Designed by Intel, PCI has gained wide acceptance as a standard bus design.PCMCIAPCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.Peripheral DeviceA piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.Pitch (keyboard)The distance between the centers of the letter keys of a keyboard.PixelThe smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.POSTPower On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your Tablet PC. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded. PPPoEPoint to Point Protocol over Ethernet.A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line.T Series.book Page 90 Thursday, July 14, 2005 2:24 PM
91GlossaryProgramAn integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.ProtocolProcedures and rules use to send and receive data between computers.- Method of sending and receiving data- Process used to handle communication errorsConditions required for communication are organized in procedures for correct transfer of information.RAMRandom Access Memory. A hardware component of your Tablet PC that holds binary information (both program and data) as long as it has the proper power applied to it.RAM ModuleA printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.ResetThe act of reloading the operating system. A reset erases all information stored in RAM.RestartSee Reset.ResumeTo proceed after interruption. In your Tablet PC this refers to returning to active operation after having been in one of the suspension states.ROMRead Only Memory. A form of memory in which infor-mation is stored by physically altering the material. Data stored in this way can not be changed by your Tablet PC and does not require power to maintain it.SDRAMSynchronous Dynamic Random Access Memory.Serial PortA connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.Shared key authenticationOne of the network authentication types for wireless LAN. Upon authentication, the access point checks whether the same network key is set to the client. If the client uses a wrong network key or the network key itself is not set, authentication is unsuccessful, allowing no communications with the access point.SMARTSelf-Monitoring, Analysis and Reporting Technology (SMART) is an emerging technology that provides near-term failure predictions for hard drives. When SMART is enabled the hard drive monitors pre-determined drive attributes that are susceptible to degradation over time. If a failure is likely to occur, SMART makes a status report available so that the Tablet PC can prompt the user to back up the data on the drive. Naturally not all failures are predictable. SMART predictability is limited to those attributes which the drive can self-monitor. In those cases where SMART can give advance warning, a considerable amount of precious data can be saved.SRAMStatic random access memory. A specific technology of making RAM which does not require periodic data refreshing.SSIDService Set IdentifierSpecifies which network you are joining. Some systems allow you to specify any SSID as an option so you can join any network.StandbyTo make inoperative for a period of time. Your Tablet PC uses various suspension states to reduce power consumption and prolong the charge of your battery.Status IndicatorA display which reports the condition of some portion of your hardware. On your Tablet PC this is an LCD screen just above the keyboard.Stereo (audio)A system using two channels to process sound from two different sources.Subnet maskTCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.SVGASuper VGA.S-VideoSuper Video. A component video system for driving a TV or computer monitor.SXGA+Short for Super Extended Graphics Array, a display specification that is capable of displaying 1400 x 1050 resolution.T Series.book Page 91 Thursday, July 14, 2005 2:24 PM
92LifeBook T Series Tablet PC - Section EightSystem ClockAn oscillator of fixed precise frequency which synchro-nizes the operation of the system and is counted to provide time of day and date.TCP/IP Transmission Control Protocol/Internet Protocol.A standard Internet protocol that is most widely used.TFTThin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.ULUnderwriters Laboratories – An independent organiza-tion that tests and certifies the electrical safety of devices.USBUniversal Serial Bus.Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer.VGAVideo Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of personal computers.VRAMVideo Random Access Memory. A memory dedicated to video display data and control.WFMWired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.Wi-Fi CompatibleWi-Fi (Wireless Fidelity) Identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guar-antees the interoperability of wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA website at: www.wirelessethernet.com.WLANWireless Local Area Network. A wireless interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.Write ProtectPrevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or direc-tory of floppy diskette or hard drive.XGAExtended VGA.Zip DriveA 100MB or 250MB read/write removable media disk drive.T Series.book Page 92 Thursday, July 14, 2005 2:24 PM
93Appendix AIntegrated WirelessLAN* User’s Guide*Optional DeviceT Series.book Page 93 Thursday, July 14, 2005 2:24 PM
94LifeBook T Series Tablet PC - Appendix AT Series.book Page 94 Thursday, July 14, 2005 2:24 PM
95Wireless LAN User’s Guide FCC REGULATORY INFORMATIONPlease note the following regulatory information related to the wireless LAN device.Regulatory Notes and StatementsWireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wire-less LAN (WLAN) devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wire-less LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:On board an airplane, orIn an explosive environment, orIn situations where the interference risk to other devices or services is perceived or identified as harmful.In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, hospitals, private buildings), obtain authorization to use these devices prior to operating the equipment.Regulatory Information/DisclaimersInstallation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its autho-rized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operating in conjunction with any other antenna or transmitter.Federal Communications Commission statementThis device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.FCC Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the distance between the equipment and the receiver.3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.4. Consult the dealer or an experienced technician for help.FCC Radio Frequency Exposure statementThe available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposure have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The wireless LAN radio device has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equip-ment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.The maximum SAR value measured from the devices are:Intel PROSet Wireless LAN(WM3945ABG) : 1.51 W/kgIntel PROSet WirelessLAN(WM3945ABG) + Bluetooth Simultaneous: 1.29 W/kgAtheros Wireless LAN (AR5BXB6) : 1.59 W/kgAtheros Wireless LAN (AR5BXB6 ) + Bluetooth Simultaneous: 1.32 W/kgExport restrictionsThis product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment.Canadian NoticeTo prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. High power radars are allocated as primary users of 5250-5350 MHz and 5650 - 5850 MHz and these radars could cause inter-ference and/or damage to LELAN (license-exempt LAN) devices operating in these bands.T Series.book Page 95 Thursday, July 14, 2005 2:24 PM
96LifeBook T Series Tablet PC - AppendixBefore Using the Wireless LANThis manual describes the procedures required to prop-erly setup and configure the integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference.Wireless LAN Devices Covered by this DocumentThis document is applicable to systems containing one of the following two devices. Most of the procedures are identical. Sections that differ between the two devices have been noted in the text:Intel PRO/Wireless 3945ABG(WM3945ABG)Atheros® AR5006EXS(AR5BXB6)Mini-Card Wireless Characteristics of the WLAN DeviceThe WLAN device is a Mini-PCI card attached to the main board of the mobile computer. It operates in two license-free RF bands, therefore eliminating the need to procure an FCC license to operate. It operates in the 2.4GHz Industrial, Scien-tific, and Medical (ISM) RF band and in the lower and middle bands of the 5GHz Unlicensed National Infor-mation Infrastructure (UNII) bands. The WLANs are capable of three operating modes, IEEE802.11a, IEEE802.11b and IEEE802.11g, wireless LAN standards governed by the IEEE (Institute of Electronics and Electrical Engineers). Encoding of data is modulated using Direct Sequence Spread Spectrum (DSSS) and Complementary Code Keying (CCK) when the WLAN device is operating in IEEE 802.11b mode and Orthogonal Frequency Divi-sion Multiplexing (OFDM) when operating in IEEE802.11a or IEEE802.11g mode. The WLAN device is Wi-Fi certified and operates at the maximum data transfer rate of 54 Mbps in IEEE802.11a or IEEE802.11g mode and 11 Mbps in IEEE802.11b mode.The maximum communication range indoors is approximately 80 feet (25 meters). However, that range will increase or decrease depending on factors such as number of walls, reflective material, or inter-ference from external RF sources.The WLAN device supports the following encryption methods - WEP, TKIP, and AES encryption.WIRELESS LAN MODES USING THIS DEVICEAd Hoc Mode (See Figure A-1)"Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers.Ad Hoc mode requires that the SSID, network authenti-cation, and encryption key settings are identically configured on all computers in the Ad Hoc network. Figure A-1. Ad Hoc Mode NetworkT Series.book Page 96 Thursday, July 14, 2005 2:24 PMNetwork connection(802.11a+b/g)network card(802.11a+b/g)
97Wireless LAN User’s Guide Access Point (Infrastructure) Mode (See Figure A-2)Infrastructure mode refers to a wireless network archi-tecture in which devices communicate with wireless or wired network devices through an Access Point. In infra-structure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the wired LAN in order to access computers, devices, and services such as file servers, printers, and databases.How to Handle This DeviceThe WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Oper-ating System that your mobile computer comes with has been pre-configured to support the WLAN device. WIRELESS NETWORK CONSIDERATIONS■The WLAN devices support IEEE802.11a+b/g.■The devices operate in the 2.4GHz ISM band the 5 GHz lower and middle UNII bands.■The maximum range of the WLAN device indoors is typically 80 feet (25 meters). Please note that the max-imum range you achieve may be shorter or longer than 80 feet, depending on factors such as access point transmit power, number and density of obstructions, or external RF interference.■Microwave ovens will interfere with the operation of WLAN device as microwave ovens operate in the same 2.4GHz frequency range that IEEE802.11b/g devices operate in. Interference by microwaves does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.■Wireless devices that transmit in the 2.4 GHz fre-quency range may interfere with the operation of WLAN devices in IEEE802.11b/g modes. Interference symptoms include reduced throughput, intermittent disconnects, and large amounts of frame errors. It is HIGHLY recommended that interfering devices be powered off to ensure proper operation of the WLAN.DEACTIVATING THE WLAN DEVICEDeactivation of the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). Fujitsu mobile computers employ two methods with which to deactivate the WLAN device:■Using the Wireless On/Off Switch, or,■In Windows, using the Intel PROSet Software or Atheros Client Utility software.Figure A-2. Access Point (Infrastructure) Mode NetworkADSL modem,cable modem,or similarInternetWired LANAccess Point*Wireless LAN*An optional hub for a wiredLAN may be required dependingupon the type of access point used.T Series.book Page 97 Thursday, July 14, 2005 2:24 PM
98LifeBook T Series Tablet PC - AppendixDeactivation using the Wireless On/Off SwitchThe WLAN device can be deactivated quickly and effi-ciently by toggling the Wireless On/Off Switch to the Off position. (Figure A-3)The wireless On/Off switch has no effect on non-Wire-less LAN models.The Wireless LAN/Bluetooth On/Off switch has no effect on systems without wireless devices.Figure A-3. Wireless LAN/Bluetooth SwitchDeactivation using the Intel PROSet SoftwareThe WLAN device can also be deactivated in Windows using the Intel PROSet Software. The procedure to accomplish this:1. Click [Start]-> [All Programs].2. Select Intel ProSet Wireless, then click on Intel ProSet Wireless from the menu that appears. The Intel ProSet Wireless utility will be displayed.3. At the bottom left corner of the window, select Wireless Off from the dropdown list. Deactivation using Atheros Client Utility software1. Click [Start] -> [Program Files] -> [Atheros] -> Atheros Client Utility.2. Choose Action and click Disable Radio.ACTIVATING THE WLAN DEVICEActivation of the WLAN device can be accomplished using the same methods as the deactivation process■Using the Wireless On/Off Switch■In Windows using the Intel PROSet Software or Atheros Software.The Wireless LAN/Bluetooth On/Off Switch will power off both the optional wireless LAN and Bluetooth devices at the same time. To enable or disable either one of the devices individually, perform the following steps:1. Slide the Wireless LAN/Bluetooth on/off switch to On position.2. In the Control Panel, double-click the Fujitsu Radio Control icon.3. In the window that appears, click the button associated with Bluetooth and/or Wireless LAN Status to enable or dis-able the individual devices.4. Click [OK].Wireless LAN/Bluetooth On/Off SwitchT Series.book Page 98 Thursday, July 14, 2005 2:24 PM
99Wireless LAN User’s Guide Configuration of the WLAN DeviceThe WLAN Device can be configured to establish wire-less network connectivity using one of the following tools:■Windows XP Wireless Zero Configuration (WZC) - The WZC allows for multiple profile setup and sup-port for most industry standard security solutions. ■Intel PROSet Software - The Intel PROSet Software allows for multiple profile setup and supports auto-matic profile switching. Support for most industry standard security solutions as well as Cisco Compati-ble Extensions (CCX) is contained in this software.■Atheros Client Utility - The Atheros Client Utility soft-ware allows for multiple profile setups and supports automatic profile switching. Support for most indus-try standard security solutions, as well as Cisco Com-patible Extensions (CCX), is contained in this software.FLOW OF OPERATIONS1. Activate the WLAN Device (See Activating the WLAN Device on page 98 for more information).2. Configure the Wireless Network parameters (Depending upon the configuration tool or utility you are using, see the appropriate section below).■Enter the network name (SSID)■Choose the appropriate WLAN architecture (Ad Hoc or Infrastructure)■Choose Authentication method: Open, Shared, WPA, or WPA-PSK■If using static WEP keys, enter static WEP key and choose key index. 3. Configure network settings (Depending upon the configuration tool or utility you are using, see the appropriate section below).■TCP/IP settings■Workgroup or Domain settings.CONFIGURATION USING WIRELESS ZERO CONFIGURATION TOOLThis section explains the procedure to properly configure the WLAN device using the WZC. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters:Network Name - Also known as the SSIDNetwork Key (WEP) - Required if using static WEP keys. Authentication Type - Open, Shared, WPA, or WPA-PSKProcedure1. Activate the WLAN device using the Wireless On/Off Switch, the Intel PROSet software, or the Atheros Client Utility.2. Click the [Start] button first and then [Control Panel].3. If the Control Panel is in Category view, switch to Classic view by clicking "Switch to Classic View" which can be found in the left frame of the Control Panel window. 4. Double-click the Network Connections icon. A list of previously configured networks will be dis-played. 5. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis-played.6. Click the [Wireless Networks] tab.7. Click [Refresh], then choose the correct SSID from the [Available Networks] window. Click [Config-ure] and proceed to step 8. Please note that only wireless networks that broadcast their SSID will be displayed. If the SSID of the wireless network is not visible, you must manually add it. This can be accomplished by clicking [Add]8. From within the Association tab configure the appropriate WLAN parameters. Please have ready the following parameters:■Network name (SSID) - ASCII string of up to 33 characters used by the WLAN to logically separate wireless networks. ■Authentication Type - Options include Open, Shared, WPA, or WPA-PSK■Network Key - If Authentication Type is Open or Shared, choices are None or WEP. If Authentica-tion Type is WPA or WPA-PSK, choices are WEP or TKIP.Ad Hoc Networks: All computers in an Ad Hoc network must be assigned with the same SSID and T Series.book Page 99 Thursday, July 14, 2005 2:24 PM
100LifeBook T Series Tablet PC - Appendixthe checkbox for the field [This is a computer to computer (ad hoc) network, wireless access points are not used.] must be checked.Access Point (Infrastructure) Networks: The SSID must be identical to the SSID of the access point(s) and the checkbox for the following field must be unchecked [This is a computer to computer (ad hoc) network wireless access points are not used.] Refer to the access point manual, or contact your network administrator9. Configure Wireless Network Key parameters (Net-work Authentication and Encryption).a. Choose the Network Authentication method appropriate for your wireless LAN. Options include Open, Shared, WPA, and WPA-PSK.Ad Hoc Networks: Network Authentication settings must be identical for all computers in the Ad Hoc network. Access Point (Infrastructure Networks): Network Authentication setting must be config-ured to match the setting of the Access Point(s). Please contact your network administrator for this information.b. Choose the Encryption method appropriate for your wireless LAN. Options for Open or Shared Authentication are None or WEP. Options for WPA or WPA-PSK are WEP or TKIP.c. If using static WEP keys, clear the check mark from the [The key is provided for me automati-cally] check box. If using an authentication method that uses dynamic WEP (e.g., WPA, WPA-PSK, 802.1x/EAP), the check box should remain checked. Please contact your network administrator for the correct settings.d. Static WEP keys (if applicable) are entered in the [Network Key] box. Configuration of the [Network Key] is not required if the [The key is provided for me automatically] check box is checked.■Static WEP keys entered in ASCII code format will be either five characters (40-bit) or thirteen characters (104-bit) in length. Valid characters are 0 - 9, A - Z.■Static WEP keys entered in hexadecimal code format will be either ten characters (40-bit) or twenty-six characters (104-bit) in length. Valid characters are 0 - 9, A - F.Ad Hoc Networks: Assign the same net-work key to all the personal computers to be connected.Access Point (Infrastructure) Networks: Assign the identical network key that is programmed into the access point. Please contact your network administrator for this information.e. If using static WEP keys, confirm the Network key by re-entering the same data in the [Confirm network key:] field.f. The Key index used must be identical to the transmit key used in the Access Point or other wireless device. This is only applicable when static WEP keys are used. Please contact your network administrator for this information.10. Access Point (Infrastructure) Networks Only: If the wireless network you are establishing connec-tivity to implements an access control security mechanism, configuration of 802.1x parameters may be necessary. Please contact your network administrator for these settings. Configuration of these parameters is not applicable to home users. 11. Click [OK] to close the [Wireless Network] window which will cause the WLAN device to re-establish wireless network connectivity using the recently configured parameters.CONFIGURATION USING INTEL PROSET SOFTWAREThis section explains the procedure to properly configure the WLAN device using the Intel PROSet Soft-ware. Pre-defined parameters will be required for this procedure. Please consult with your network adminis-trator for these parameters:Network Name - Also known as the SSIDNetwork Key (WEP) - Required if using static WEP keys. Authentication Type - Open, Shared, WPA, or WPA-PSKProcedure1. Activate the WLAN device using either the Wireless On/Off Switch or the Intel PROSet software.2. Click the [Start] button first and then [Control Panel].3. If the Control Panel is in Category view, switch to Classic view by clicking "Switch to Classic View" which can be found in the left frame of the Control Panel window. 4. Double-click the icon [Intel PROSet] to execute the Intel PROSet Software.5. From the General page, click the Networks tab. T Series.book Page 100 Thursday, July 14, 2005 2:24 PM
101Wireless LAN User’s Guide 6. Click the [Add] button. The General Settings dialog displays. 7. From the General page, click the Networks tab. 8. Click the [Add] button. The General Settings dialog displays. 9. Enter a profile name in the Profile Name field. 10. Enter the network SSID, in the Network Name (SSID) field. 11. Click Infrastructure or Ad Hoc for the operating mode. 12. The Mandatory AP option is only used if Infra-structure mode is selected. Use this option to con-nect to a specific access point. Click the Mandatory AP button, enter the MAC address for the access point. Click OK to save the setting and return to the General Settings page. 13. If you are using Cisco CCX, click the Enable Cisco Client eXtentions option to enable Cisco CKIP data encryption on the Security Settings page. If you have checked the Cisco's "Mixed-Cell" box in the Advanced Setting, this option must also be checked. 14. Click Next.15. Click the Security tab16. Select Open, Shared, WPA, or WPA-PSK in the Network Authentication options. 17. Select either None, WEP, CKIP (if Enable Cisco Cli-ent eXtentions is enabled on the General Settings page), or TKIP for the data encryption. 18. If WEP is selected, select either 64 or 128-bit for the Encryption Level. 19. Select the key index 1, 2, 3 or 4. 20. Enter the WEP key if required. If your network does not employ a 802.1x/EAP security mechanism, please skip to step 24.21. Click the 802.1x Enabled checkbox to enable the 802.1x security option. Please contact your network administrator if configuration of this setting is required.22. Select the appropriate 802.1x/EAP Type. Please contact your network administrator if configura-tion of this setting is required.23. After selecting your authentication type, click the Configure button to open the Settings dialog. Enter the user name and password of the user you have created on the authentication server. The user name and password do not have to be the same as name and password of your current Windows user login. The "Server Identity" can be use the default setting. The "Client Certificate" should be the one obtained from your RADIUS server or other certifi-cation server. 24. Click Close to save the settings. 25. From the General settings page, click the new pro-file name shown in the Profile List. Use the up and down arrows to position the priority of the new profile in the priority list. 26. Click the Advanced button to set the network con-nection preferences. 27. Click the Connect button to connect to the net-work. 28. Click OK to close the Intel(R) PROSet for Wireless utilityCONFIGURATION USING ATHEROS CLIENT UTILITY SOFTWAREThis section explains the procedure to properly configure the WLAN device using the Atheros Client Utility. Pre-defined parameters will be required for this procedure. Please consult with your network adminis-trator for these parameters:Network Name - Also known as the SSIDNetwork Key (WEP) - Required if using static WEP keys. Authentication Type - Open, Shared, WPA, or WPA-PSKProcedure1. Activate the WLAN device using either the Wireless On/Off Switch or the Atheros Client Utility2. Click the [Start] button first and then [Control Panel].3. If the Control Panel is in Category view, switch to Classic view by clicking "Switch to Classic View" which can be found in the left frame of the Control Panel window. 4. Double-click the icon [Atheros Client Utility] to execute the Atheros Client Utility.5. From the Current Status page, click the Profile Management tab. 6. If this is your first time using this utility, highlight the profile [Default] and Click the [Modify] button, otherwise Click the [New] button. The General Set-tings dialog displays. 7. From the General page, enter a profile name in the Profile Name field. T Series.book Page 101 Thursday, July 14, 2005 2:24 PM
102LifeBook T Series Tablet PC - Appendix8. Enter the network SSID, in the SSID1 field. If you wish to create a profile that can connect to up to 3 different wireless networks, SSID's can be entered in the SSID2 and SSID3 fields as well.9. Click the Security tab. 10. The Security tab allows for the configuration of the Security modes listed in the table below. Please select the radio button of the desired security mode. If these settings are not known to you, please consult with your network administrator for the correct settings. 11. Click OK12. Click the Advanced tab13. The Advanced tab allows for the configuration of the options detailed in the table below.14. Click OK15. If the profile you just created does not activate immediately, click the Profile Management tab, highlight the desired Profile, and click Activate.16. Click OK to close the Atheros Client Utility.Field Name DescriptionWPA Enables the use of Wi-Fi Protected Access. Choosing WPA opens the WPA EAP drop-down menu. Options include TLS and PEAP. If these settings are not known to you, please consult with your network administrator for the correct settings. WPA-PSK Enables WPA-Pre-Shared Key. Click on the Configure button to enter the WPA Passphrase. If these settings are not known to you, please consult with your network administrator for the correct settings. 802.1x Enables 802.1x security. If these settings are not known to you, please consult with your network administrator for the correct settings. Choosing this option opens the 802.1x EAP type drop-down menu. Options include TLS, PEAP, and LEAPPre-Shared Key Enables the use of pre-shared keys that are defined on both the access point and the station. This is where static WEP keys are entered. Click the Configure button to fill in the Define Pre-Shared Keys window.None No securityField Name DescriptionPower Save ModeOptions are Maximum, Normal, or OffNetwork Type Options are AP (Infrastructure) or Ad Hoc802.11b PreambleSpecifies the preamble setting in 802.11b. The default setting is Short and Long (Access Point mode), which allows both short and long headers in the 802.11b frames. Set to Long Only to override allowing short frames.Transmit Power LevelOptions are 100%, 50%, 25%, 12.5% or Lowest transmit power (0mW)Wireless Mode Specifies 5 GHz 54 Mbps, 5 GHz 108 Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps operation in an access point network.Wireless Mode when Starting Ad Hoc NetworkSpecifies 5GHz 54 Mbps, 5 GHz 108 Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps to start an Ad Hoc network if no matching network name is found after scanning all available modes.T Series.book Page 102 Thursday, July 14, 2005 2:24 PM
103Wireless LAN User’s Guide CONNECTION TO THE NETWORKThis section explains connection to the network.If there is an administrator of the network, contact the network administrator for data settings.Setting the networkPerform the “Setting TCP/IP” and “Confirming the computer and work group names” operations required for network connection.Setting TCP/IP1. Click the [Start] button first and then [Control Panel].2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click [Network Connections]. A list of cur-rently installed networks will be displayed.4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis-played. The [Wireless Network Connection Proper-ties] window will be displayed.5. Click the [General] tab if it is not already selected.6. Click [Internet Protocol (TCP/IP] and then click [Properties]. The [Internet Protocol (TCP/IP) Properties] window will be displayed.7. Set the IP address as follows:■For ad hoc connection: Select [Use the following IP address:] and then enter data for [IP address] and [Subnet mask]. See page 109 for IP address setting.■For access point (infrastructure) connection: If your network uses DHCP, select [Obtain an IP address automatically] and [Obtain DNS server address automatically]. If your network uses static IP addresses, consult with your network adminis-trator for the correct IP address settings.8. Click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window.9. Click the [OK] button.10. Close the [Network Connection] window. Following this operation, confirm the names of the computer and the workgroup as follows.Confirming the computer and work group names1. Click the [Start] button, then [Control Panel].2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click the [System] icon. The [System Prop-erties] window will be displayed.4. Click the [Computer Name] tab.5. Confirm the settings of [Full computer name:] and [Workgroup:].a. The setting of [Full computer name:] denotes the name for identifying the computer. Any name can be assigned for each personal computer. Enter the desired name in less than 15 ASCII character code format. Identifiability can be enhanced by entering the model number, the user name, and other factors.b. [Workgroup name] is the group name of the network. Enter the desired name in less than 15 ASCII character code format.For ad hoc connection: Assign the same network name to all personal computers existing on the network.For access point (infrastructure) connection: Assign the name of the work group to be accessed.6. Click the [OK] button. If a message is displayed that requests you to restart the personal computer, click [Yes] to restart the computer.Setting the sharing functionSet the sharing function to make file and/or printer sharing with other network-connected personal computers valid.This operation is not required unless the sharing func-tion is to be used.To change the setting of the IP address, you need to be logged in from Windows as an administrator.To modify the computer name and/or the work group name, you need to be logged in from Windows as an administrator.To change the name, click [Change] and then proceed in accordance with the instruction messages displayed on the screen.T Series.book Page 103 Thursday, July 14, 2005 2:24 PM
104LifeBook T Series Tablet PC - AppendixThe folder and printer for which the sharing function has been set will be usable from any personal computer present on the network.Setting the Microsoft network-sharing service1. Click the [Start] button first and then [Control Panel]. 2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click [Network Connections]. A list of cur-rently installed networks will be displayed.4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis-played. The [Wireless Network Connection Proper-ties] window will be displayed.5. If [File and Printer Sharing for Microsoft Net-works] is displayed, proceed to step 6. If [File and Printer Sharing for Microsoft Networks] is not dis-played, skip to step 7.6. Make sure that the [File and Printer Sharing for Microsoft Networks] check box is checked, and then click the [OK] button. Skip to “Setting file-sharing function”.7. Click [Install]. The [Select Network Component Type] window will be displayed.8. Click [Service], then click the [Add] button. The [Select Network Service] window will be displayed.9. Click [File and Printer Sharing for Microsoft Net-works] and then click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window, and [File and Printer Sharing for Microsoft Networks] will be added to the list.10. Click the [Close] button.Setting the file-sharing functionThe procedure for setting the file-sharing function follows, with the “work” folder in drive C: as an example.1. Click the [Start] button first and then [My Com-puter]. 2. Double-click [Local disk (C:)].3. Right-click the “work” folder (or whichever folder you want to share), and then click [Sharing and Security...] in the menu displayed. The [Folder Name Properties] window will be displayed.4. Click [Sharing] if it isn’t already selected.5. Click the link stating “If you understand the secu-rity risks, but want to share files without running the wizard, click here”.6. Click “Just enable file sharing” and click [OK].7. Check the [Share this folder on the network] check box.8. Click the [OK] button. The folder will be set as a sharable folder, and the display of the icon for the “work.” folder will change.Setting the printer-sharing function1. Click the [Start] button first and then [Printers and FAX]. A list of connected printers will be displayed.2. Right-click the printer for which the sharing func-tion is to be set, and then click [Sharing] in the menu displayed. The property window correspond-ing to the selected printer will be displayed.To share a file and/or the connected printer, you need to be logged in as an administrator. Setting the file-sharing function for the file which has been used to execute Network Setup Wizard is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the file-sharing function easily without using Network Setup Wizard are given below.To specify the corresponding folder as a read-only folder, select the [Read only] checkbox under the General tab.Setting the printer-sharing function when Network Setup Wizard has been executed is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the printer-sharing function without using Network Setup Wizard are laid down below.T Series.book Page 104 Thursday, July 14, 2005 2:24 PM
105Wireless LAN User’s Guide 3. Click the [Sharing] tab.4. Click [Share this printer].5. Enter the sharing printer name in [Share name].6. Click the [OK] button. Confirming connectionAfter you have finished the network setup operations, access the folder whose sharing has been set for other personal computers. Also, confirm the status of the radio waves in case of trouble such as a network connection failure.Connecting your personal computer to another personal computer1. Click [Start] first and then [My Computer]. The [My Computer] window will be displayed in the left frame.2. Click [My Network Places] in the “Other Places” list. The window [My Network Places] will be dis-played.3. Click [View workgroup computers] under Network Tasks in the left frame.4. Double-click the personal computer to which your personal computer is to be connected. The folder that was specified in “Setting the file-sharing func-tion” on page 104 will be displayed.5. Double-click the folder to be accessed.Confirming the status of the radio1. Right-click the Intel PRO Wireless icon in the lower right corner of the screen.2. Click [Open Intel PROSet for Wireless]. The Intel PROSet for Wireless window opens.3. Contained within the General tab and the Details section (accessed by pressing the [Details] button), you will find the current operating status of the radio. (When the radio is turned off or the com-puter is not yet connected, some of the conditions will not be displayed.)■Network Name (SSID)Displays the Network Name (SSID) currently used by the radio.■Profile NameThe current configuration profile is displayed.■ModeDisplays the current operating mode. [Infra-structure (AP)] or [Ad Hoc] will be displayed.■SecurityDisplays the current security status of the profile being used:None: No encryption used.WEP: WEP encryption algorithm used.CKIP: WEP encryption algorithm used.TKIP: WEP encryption algorithm used.■SpeedDisplays the highest data rate of the associated access point in mega-bits-per-second (Mbps) until data transfer occurs.802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, or 54. 802.11b: 1, 2, 5.5, or 11.■Band (Frequency)Displays the current band and frequency being used. Displays Out of Range if no band and frequency is displayed. Displays:802.11g (2.4 GHz) or 802.11b (2.4 GHz)■ChannelDisplays the current transmit and receive channel being used.■802.1x ProtocolDisplays Enabled if the profile uses 802.1x authentication. Default is Disabled.In the case of access point (infrastructure) connection, enter the necessary data for the access point before confirming connection. Refer to the manual of the access point for the access point setup procedure.T Series.book Page 105 Thursday, July 14, 2005 2:24 PM
106LifeBook T Series Tablet PC - AppendixTroubleshootingCauses and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. Problem Possible Cause Possible SolutionUnavailable network connectionIncorrect network name (SSID) or network keyAd hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.Access Point (Infrastructure) connection: set the network name (SSID) and network key to the same values as those of the access point. Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary. For the method of setting network authentication, refer to the section of this chapter related to the configuration tool or utility you are using.·Weak received signal strength and/or link qualityAd hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight.Access Point (Infrastructure) connection: Retry connection after short-ening the distance to the access point or removing any obstacles for better sight.(See Confirming connection on page 105 for more information).The WLAN device has been deactivated or disabledCheck if the wireless switch is turned ON. Also verify “Disable Radio” is not checked in “Network setting” window. (See Activating the WLAN Device on page 98 for more information).The computer to be connected is turned offCheck if the computer to be connected is turned ON.RF interference from Access Points or other wireless networksThe use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device.Wireless network authentication has failedRe-check your Network Authentication, Encryption, and Security settings. Incorrectly configured security settings such as an incorrectly typed WEP key, a mis-configured LEAP username, or an incorrectly chosen authentication method will cause the LAN device to associate but not authenticate to the wireless network.Incorrectly configured network settingsRecheck the configuration of your network settings.For the method of checking, refer to the following page:·“Connection to the Network” on page 103.Incorrect IP address configurationThis only applies to networks using static IP addresses. Please contact your network administrator for the correct settings.T Series.book Page 106 Thursday, July 14, 2005 2:24 PM
107Wireless LAN User’s Guide Wireless LAN GlossaryAd Hoc ModeAd Hoc Mode refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion. For details, refer to “Ad hoc connection” on page 96.ChannelRange of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.DHCP (Dynamic Host Configuration Protocol)A protocol that provides a means to dynamically allocate IP addresses to computers on a local area network.DNS (Domain Name System)A data query service that provides a mechanism with which to translate host names into Internet addresses.IEEE802.11aWireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands. IEEE802.11bWireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz ISM band. Access pointWireless network device used to bridge wireless and wired network traffic. IP addressThe logical 32-bit host address defined by the Internet Protocol that uniquely identifies a computer on a network. The IP address is usually expressed in dotted decimal notation.LAN (Local Area Network)A LAN or Local Area Network is a computer network (or data communications network) which is confined to a limited geographical area.MAC address (Media Access Control Address)A MAC address (also called an Ethernet address or IEEE MAC address) is the 48-bit address (typically written as twelve hexadecimal digits, 0 through 9 and A through F, or as six hexadecimal numbers separated by periods or colons, e.g., 0080002012ef, 0:80:0:2:20:ef) which uniquely identifies a computer that has an Ethernet interface.MTU (Maximum Transmission Unit)The maximum size of data which can be transmitted at one time in networks including the Internet. In an envi-ronment whose maximum size of data is too large to correctly receive data, normal communications can be restored by setting the size of MTU to a smaller value.Network keyData that is used for encrypting data in data communi-cation. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.Network name (SSID: Security Set Identifier)When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.Open system authenticationNull authentication method specified in the 802.11 stan-dard that performs no authentication checks on a wire-less client before allowing it to associate.PPPoE (Point to Point Protocol over Ethernet)A method of allowing the authentication protocol adopted in telephone line connection (PPP) to be used over an Ethernet.ProtocolA procedure or rule of delivering data among computers. Ordered data communication is allowed by making all conditions required for communication including the method of data transmission/reception and actions upon communication errors into proce-dures.T Series.book Page 107 Thursday, July 14, 2005 2:24 PM
108LifeBook T Series Tablet PC - AppendixShared key authentication802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP. If the client has the wrong key or no key, authentication will fail and the client will not be allowed to associate with the AP. Shared key authentica-tion is not considered secure, because a hacker who detects both the clear-text challenge and the same chal-lenge encrypted with a WEP key can decipher the WEP key.SSID (Service Set Identifier)Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID. Because the SSID is broadcast in plain text, it does not supply any security to the network. Subnet maskTCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.TCP/IP (Transmission Control Protocol/Internet Protocol)A standard protocol of the Internet. Wi-Fi Wi-Fi, or Wireless Fidelity, is a set of standards for wire-less local area networks (WLAN) based on the IEEE 802.11 specifications. Certified products can use the official Wi-Fi logo, which indicates that the product is interoperable with any other product also showing that logo.T Series.book Page 108 Thursday, July 14, 2005 2:24 PM
109Wireless LAN User’s Guide IP address informationIf IP address is unknown, set IP address as follows:If you have an access point (DHCP server) on the network, set the IP address as follows:[Obtain an IP address automatically]If the IP address is already assigned to the computer in the network, ask the network administrator to check the IP address to be set for the computer.If no access point is found in the network:An IP address is expressed with four values in the range between 1 and 255.Set the each computer as follows: The value in paren-theses is a subnet mask.<Example>Computer A: 192.168.100.2 (255.255.255.0)Computer B: 192.168.100.3 (255.255.255.0)Computer C: 192.168.100.4 (255.255.255.0)::Computer X: 192.168.100.254 (255.255.255.0)IP addressing is much more complicated than can be briefly explained in this document. You are advised to consult with your network administrator for additional information.A DHCP server is a server that automatically assigns IP addresses to computers or other devices in the network. There is no DHCP server for the AdHoc network.T Series.book Page 109 Thursday, July 14, 2005 2:24 PM
110LifeBook T Series Tablet PC - AppendixSpecifications* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/104 bits after subtracting the fixed length of 24 bits.*** Depending on practical environments, the allowable number of computers to be connected may be decreased.Item SpecificationType of network Conforms to IEEE 802.11a/802.11b/g (Wi-Fi based)*Transfer rate (Automatic switching)IEEE 802.11a/g: 54 Mbps maximum data rate IEEE 802.11b: 11 Mbps maximum data rateActive frequency 802.11b/g: 2400~2473 MHz 802.11a: 4900 ~ 5850 MHzNumber of channels 802.11a: 8 independent channels802.11b/g: 11 channels, 3 non-overlapping channels Security Encryption Types - WEP, TKIP, AES**WPA 1.0 compliant Encryption Keylengths Supported: 64 bits, 128 bits, and 152 bits (Using AES encryption only)802.1x/EAPCCX 1.0 compliantMaximum recommended number of computers to be connected over wireless LAN (during ad hoc connection)10 units or less ***T Series.book Page 110 Thursday, July 14, 2005 2:24 PM
111Wireless LAN User’s Guide Using the Bluetooth DeviceThe Integrated Bluetooth module (EYTF3CSFT) is an optional device available for Fujitsu mobile computers. WHAT IS BLUETOOTHBluetooth technology is designed as a short-range wire-less link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other. WHERE TO FIND INFORMATIONABOUT BLUETOOTHThe Bluetooth module contains a robust Help user’s guide to assist you in learning about operation of the Bluetooth device.To access the Help file, click [Start] -> All Programs, and click on Toshiba. Select Bluetooth, then select User’s Guide.For additional information about Bluetooth Technology, visit the Bluetooth Web site at: www.bluetooth.com.FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located at thethe LCD screen and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.Canadian NoticeTo prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.WarrantyUsers are not authorized to modify this product. Any modifications invalidate the warranty.This equipment may not be modified, altered, or changed in any way without signed written permission from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and Industry Canada and the warranty.The Wireless LAN/Bluetooth On/Off Switch will power off both the optional wireless LAN and Bluetooth devices at the same time. To enable or disable either one of the devices individually, perform the following steps:1. Slide the Wireless LAN/Bluetooth on/off switch to On position.2. In the Control Panel, double-click the Fujitsu Radio Control icon.3. In the window that appears, click the button associated with Bluetooth and/or Wireless LAN Status to enable or dis-able the individual devices.4. Click [OK].T Series.book Page 111 Thursday, July 14, 2005 2:24 PMmiddle of edge of
112LifeBook T Series Tablet PC - AppendixT Series.book Page 112 Thursday, July 14, 2005 2:24 PM
113Appendix BUsing the Fingerprint Sensor* * Optional DeviceT Series.book Page 113 Thursday, July 14, 2005 2:24 PM
114LifeBook T Series Tablet PC – Appendix BT Series.book Page 114 Thursday, July 14, 2005 2:24 PM
115Using the Fingerprint SensorFingerprint Sensor DeviceINTRODUCING THE OPTIONAL FINGERPRINT SENSOR DEVICEYour system may have an optional fingerprint sensor device in the location at which other models have a scroll button. (Figure B-1) Figure B-1 Fingerprint sensorWith a fingerprint sensor, you can avoid having to enter a username and password every time you want to:■Log onto Windows■Recover from suspend mode■Cancel a password-protected screen saver■Log into homepages that require a username and pass-wordAfter you have “enrolled” - or registered - your finger-print, you can simply swipe your fingertip over the sensor for the system recognize you. The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and on-line passwords. OmniPass requires users to authenticate themselves using the fingerprint sensor before granting access to the Windows desktop. This device results in a secure authentication system for restricting access to your computer, applications, web sites, and other password-protected resources.OmniPass presents a convenient graphical user interface, through which you can securely manage passwords, users, and multiple identities for each user.GETTING STARTEDThis section guides you through the preparation of your system for the OmniPass fingerprint recognition application. You will be led through the OmniPass installation process. You will also be led through the procedure of enrolling your first user into OmniPass. INSTALLING OMNIPASSIf OmniPass has already been installed on your system, skip this section and go directly to “User Enrollment” on page 116. You can determine whether OmniPass has already been installed by checking to see if the following are present:■The presence of the gold key-shaped OmniPass icon in the system tray at the bottom right of the screen.■The presence of the Softex program group in the Programs group of the Start menuSystem RequirementsThe OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows:■Windows XP Home Edition or Windows XP Profes-sional operating system■At least 35 MB available hard disk spaceInstalling the OmniPass ApplicationIf OmniPass is already installed on your system, go to “User Enrollment” on page 116. Otherwise continue with this section on software installation.To install OmniPass on your system you must:1. Insert the installation media for the OmniPass appli-cation into the appropriate drive. If you are installing from CD-ROM or DVD-ROM, you must find and launch the OmniPass installation program (setup.exe) from the media.2. Follow the directions provided in the OmniPass installation program. Specify a location to which you would like OmniPass installed. It is recom-mended that you NOT install OmniPass in the root directory (e.g. C:\). 3. Once OmniPass has completed installation you will be prompted to restart you system. Once your system has rebooted you will be able to use OmniPass. If you choose not to restart immediately after installation, OmniPass will not be available for use until the next reboot.Although the system may have a fingerprint sensor in place of a scroll button, the fingerprint sensor can be used for scrolling. Simply move your fingerprint over the sensor the same as you would use a scroll button. For installation, OmniPass requires that the user installing OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass installation.T Series.book Page 115 Thursday, July 14, 2005 2:24 PM
116LifeBook T Series Tablet PC – Appendix BThe installation program automatically places an icon (Softex OmniPass) in the Windows Control Panel as well as a golden key shaped icon in the taskbar. Verifying Information about OmniPassAfter you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system.To check the version information of OmniPass:1. From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen),or,Click the Start button, select Settings, and click Control Panel (if you are using Windows XP you will see the Control Panel directly in the Start menu; click it, then click Switch to Classic View). Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear. If it does not appear, then the program is not properly installed,or,Click the Start button, select Programs, and from the submenu select the Softex program group, from that submenu click OmniPass Control Center.2. Select the About tab at the top of the OmniPass Control Panel. The About tab window appears with version information about OmniPass.Uninstalling OmniPassTo remove the OmniPass application from your system:1. Click Start on the Windows taskbar. Select Settings, and then Control Panel.2. Double-click Add/Remove Programs.3. Select OmniPass, and then click Change/Remove.4. Follow the directions to uninstall the OmniPass application.5. Once OmniPass has finished uninstalling, reboot your system when prompted.USER ENROLLMENTBefore you can use any OmniPass features you must first enroll a user into OmniPass.Master Password ConceptComputer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access. This can result in dozens of sets of creden-tials that you have to remember.During OmniPass user enrollment a "master password” is created for the enrolled user. This master password “replaces” all other passwords for sites you register with OmniPass. Example: A user, John, installs OmniPass on his system (his home computer) and enrolls an OmniPass user with username “John_01” and password “freq14”. He then goes to his webmail site to log onto his account. He inputs his webmail credentials as usual (username “John_02” and password “lifebook”), but instead of clicking [Submit], he directs OmniPass to Remember Password. Now whenever he returns to that site, OmniPass will prompt him to supply access credentials. John enters his OmniPass user credentials (“John_01” and “freq14”) in the OmniPass authentication prompt, and he is allowed into his webmail account. He can do this with as many web sites or password protected resources he likes, and he will gain access to all those sites with his OmniPass user credentials (“John_01” and “freq14”). This is assuming he is accessing those sites with the system onto which he enrolled his OmniPass user. OmniPass does not actually change the credentials of the password protected resource. If John were to go to an Internet cafe to access his webmail, he would need to enter his original webmail credentials (“John_02” and “lifebook”) to gain access. If he attempts his OmniPass user credentials on a system other than where he enrolled that OmniPass user, he will not gain access.Basic EnrollmentThe Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified other-wise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard.1. Click Enroll to proceed to username and password verification. By default, the OmniPass Enrollment Wizard enters the credentials of the currently logged in Windows user.2. Enter the password you use to log in to Windows. This will become the “master password” for this OmniPass user. In most cases, the Domain: value For uninstallation, OmniPass requires that the user uninstalling OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass uninstallation.The enrollment procedure assumes you have no hardware authentication devices or alternate storage locations that you wish to integrate with OmniPass. If you desire such functionality, consult the appropriate sections of this document.T Series.book Page 116 Thursday, July 14, 2005 2:24 PM
117Using the Fingerprint Sensorwill be your Windows computer name. In a corpo-rate environment, or when accessing corporate resources, the Domain: may not be your Windows computer name. Click [Next] to continue.3. In this step OmniPass captures your fingerprint. Refer to “Enrolling a Fingerprint” on page 117 for additional information.4. Next, choose how OmniPass notifies you of various events. We recommend you keep Taskbar Tips on Beginner mode taskbar tips and Audio Tips on at least Prompt with system beeps only until you get accustomed to how OmniPass operates. Click [Next] to proceed with user enrollment. You will then see a Congratulations screen indicating your completion of user enrollment.5. Click [Done] to exit the OmniPass Enrollment Wizard. You will be asked if you’d like to log in to OmniPass with your newly enrolled user; click [Yes].Enrolling a FingerprintEnrolling a fingerprint will increase the security of your system and streamline the authentication procedure. You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the User Settings area. Click Enroll Authentication Device and authenticate at the authentication prompt to start device enrollment.1. During initial user enrollment, you will be prompted to select the finger you wish to enroll. Fingers that have already been enrolled will be marked by a green check. The finger you select to enroll at this time will be marked by a red arrow. OmniPass will allow you re-enroll a finger. If you choose a finger that has already been enrolled and continue enrollment, OmniPass will enroll the fingerprint, overwriting the old fingerprint. Select a finger to enroll and click [Next].2. It is now time for OmniPass to capture your selected fingerprint. It may take a several capture attempts before OmniPass acquires your fingerprint. Should OmniPass fail to acquire your fingerprint, or if the capture screen times out, click [Back] to restart the fingerprint enrollment process. Your system has a “swipe” fingerprint sensor (See Figure B-1). A swipe sensor is small and resembles a skinny elongated rectangle. To capture a fingerprint, gently swipe or pull your fingertip over the sensor (starting at the second knuckle) towards yourself. Swiping too fast or too slow will result in a failed capture. The Choose Finger screen has a [Practice] button; click it to practice capturing your finger-print. When you are comfortable with how your fingerprint is captured, proceed to enroll a finger.3. Once OmniPass has successfully acquired the finger-print, the Ver if y F i ng e r pr i n t screen will automati-cally appear. To verify your enrolled fingerprint, swipe your fingertip over the sensor four times to verify. Successful fingerprint verification will show a green fingerprint in the capture window and the text Verification Successful under the capture window. (An unsuccessful swipe will be indicated in red.)USING OMNIPASSYou are now ready to begin using OmniPass. Used regu-larly, OmniPass will streamline your authentications.Password ReplacementYou will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials. OmniPass can detect these prompts and you can teach OmniPass your login credentials. The next time you go to that website, you can authenticate with your fingerprint to gain access.OmniPass Authentication ToolbarAfter installing OmniPass and restarting, you will notice a dialog you have not seen before at Windows Logon. This is the OmniPass Authentication Toolbar, and it is displayed whenever the OmniPass authentication system is invoked. The OmniPass authentication system may be invoked frequently: during Windows Logon, during OmniPass Logon, when unlocking your workstation, when resuming from standby or hibernate, when unlocking a password-enabled screensaver, during pass-word replacement for remembered site or application logins, and more. When you see this toolbar, OmniPass is prompting you to authenticate.The Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not. When you click the icon for an unse-lected authentication method, the authentication prompt associated with that method is displayed.When prompted to authenticate, you must supply the appropriate credentials: an enrolled finger for the finger-print capture window or your master password for the master password prompt (the key icon).Remembering a PasswordOmniPass can remember any application, GUI, or pass-word protected resource that has a password prompt.Using the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint.T Series.book Page 117 Thursday, July 14, 2005 2:24 PM
118LifeBook T Series Tablet PC – Appendix BGo to a site that requires a login (username and pass-word), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login). Right-click the OmniPass system tray icon and select Remember Password from the submenu. The Windows arrow cursor will change to a golden key OmniPass cursor. Click this OmniPass cursor in the login prompt area, but do not click the [Login] or [Submit] button.Associating a Friendly NameAfter clicking the OmniPass key cursor near the login prompt, OmniPass will prompt you to enter a “friendly name” for this site. You should enter something that reminds you of the website, the company, or the service you are logging into. In its secure database, OmniPass associates this friendly name with this website.Additional Settings for Remembering a SiteWhen OmniPass prompts you to enter a “friendly name” you also have the opportunity to set how OmniPass authenticates you to this site. There are three effective settings for how OmniPass handles a remembered site.The default setting is Automatically click the “OK” or “Submit” button for this password protected site once the user is authenticated. With this setting, each time you navigate to this site OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass, you will automatically be logged into the site. Less secure is the option to Automatically enter this password protected site when it is activated. Do not prompt for authentication. Check the upper box to get this setting, and each time you navigate to this site OmniPass will log you into the site without prompting you to authenticate.If you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master pass-word or fingerprint authentication device. Once you have authenticated with OmniPass your credentials will be filled in to the site login prompt, but you will have to click the website [OK], [Submit], or [Login] button to gain access to the site. Click Finish to complete the remember password proce-dure. The site location, the credentials to access the site, and the OmniPass authentication settings for the site are now stored in the OmniPass secure database. The OmniPass authentication settings (Settings for this Pass-word Site) can always be changed in Vault Management.Logging in to a Remembered SiteWhether or not OmniPass prompts you to authenticate when you return to a remembered site is determined by Settings for this Password Site and can be changed in Vault Management. The following cases are applicable to using OmniPass to login to: Windows, remembered web sites, and all other password protected resources.With Master PasswordOnce you return to a site you have remembered with OmniPass, you may be presented with a master pass-word prompt. Enter your master password and you will be allowed into the site.Logging into Windows with a Fingerprint DeviceWhen logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.In Windows XP, your login options must be set either for classic login, or for fast user switching and logon screen to be enabled to use your fingerprint to log on to Windows. To change this go to Control Panel, select User Accounts and then click Change the way users log on or off. If your Windows screensaver is password protected, the fingerprint capture window will now appear next to screensaver password dialog during resume. You can authenticate to your screensaver pass-word prompt with your enrolled finger.Password ManagementOmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Vau lt Man a g e-ment; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Pass-words under Vault Settings. You will see the Manage Passwords interface, with a list of friendly names.This setting is more convenient in that whenever you go to a site remembered with this setting, you will bypass any authentication procedure and gain instant access to the site. But should you leave your system unattended with your OmniPass user logged in, anyone using your system can browse to your password protected sites and gain automatic access.If a machine is locked and OmniPass detects a different user logging back in with a fingerprint, the first user will be logged out and the second user logged in.T Series.book Page 118 Thursday, July 14, 2005 2:24 PM
119Using the Fingerprint SensorYou can view the credentials stored for any remembered website by highlighting the desired resource under Pass-word Protected Dialog and clicking Unmask Values. Should a password be reset, or an account expire, you can remove stored credentials from OmniPass. Highlight the desired resource under Password Protected Dialog and click Delete Page. You will be prompted to confirm the password deletion.The two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site.OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site. The exception to the above rule is the resetting of your Windows password. If your password is reset in Windows, then the next time you login to Windows, OmniPass will detect the password change and prompt you to “Update” or “Reconfirm” your password with OmniPass. Enter your new Windows password in the prompt(s) and click OK and your OmniPass "master password" will still be your Windows password.OmniPass User IdentitiesIdentities allow OmniPass users to have multiple accounts to the same site (e.g., bob@biblomail.com and boballen@biblomail.com). If OmniPass did not provide you identities, you would be limited to remembering one account per site.To create and manage identities, double-click the OmniPass key in the system tray. Click Vault M a nage -ment; OmniPass will prompt you to authenticate. Once you gain access to Vault Management, click Manage Identities under Vault Settings. You can only manage the identities of the currently logged in OmniPass userTo add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply]. You can now switch to the new identity and start remembering passwords.To delete an identity, highlight the identity you want to delete and click [Delete Identity], then click [Apply].To set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automati-cally be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password".Choosing User Identity during LoginTo choose your identity during login, type your user-name in the User Name: field. Press [Tab] and see that the Domain: field self-populates. Click the Password: field to bring the cursor to it, and you will see the pull-down menu in the Identity: field. Select the identity you wish to login as and then click OK to login.Switch User IdentityTo switch identities at any time, right-click the OmniPass system tray icon and click Switch User Iden-tity from the submenu. The Switch Identity dialog will appear. Select the desired identity and then click OK.Identities and Password ManagementOn the Manage Passwords interface of the Va u l t Management tab of the OmniPass Control Center, there is a pull-down selection box labeled, Identity. This field lets you choose which identity you are managing pass-words for. When you select an identity here, only those password protected dialogs that are associated with that identity are shown. You can perform all the functions explained in “Password Management” on page 118.CONFIGURING OMNIPASSThis section gives an overview of both the Export/Import function and the OmniPass Control Center. Exporting and Importing UsersUsing the OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and any enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported. When you delete an identity, all of its associated remembered sites and password protected dialogs are lost.■You should periodically export your user profile and store it in a safe place. If anything happens to your system, you can import your OmniPass profile to a new system and have all your remem-bered settings and fingerprints instantly.■You don't forget the Windows login credentials when exporting. When you examine the importation, you are prompted for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain.T Series.book Page 119 Thursday, July 14, 2005 2:24 PM
120LifeBook T Series Tablet PC – Appendix BExporting an OmniPass User ProfileTo export a user, open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Exports an OmniPass user profile. OmniPass will prompt you to authenticate. Upon successfully authenti-cation, you must name the OmniPass user profile and decide where to save it. An .opi file is generated, and you should store a copy of it in a safe place.This .opi file contains all your user specific OmniPass data, and it is both encrypted and password protected. This user profile does NOT contain any of your encrypted data files.Importing an OmniPass User ProfileTo import an OmniPass user open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Imports a new user into OmniPass and then select OmniPass Import/Export File (*.opi) and click Next. OmniPass will then prompt you to browse for the file you had previously exported (.opi file). When you select the .opi file for importation, OmniPass will prompt you for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name.OmniPass will notify you if the user was successfully imported.Things to Know Regarding Import/Export■Assume you export a local Windows User profile from OmniPass. You want to import that profile to another machine that has OmniPass. Before you can import the profile, a Windows user with the same login cre-dentials must be created on the machine importing the profile.Example: I have a Windows user with the username “Tom” and the password “Sunshine” on my system. I have enrolled Tom into OmniPass and remembered passwords. I want to take all my passwords to new sys-tem. I export Tom’s OmniPass user profile. I go to my new system and using the Control Panel I create a user with the username "Tom" and the password "Sun-shine". I can now successfully import the OmniPass user data to the new system.■If you export an OmniPass-only user, you can import that user to any computer running OmniPass, pro-vided that a user with that name is not already enrolled in OmniPass. ■If you attempt to import a user profile who has the same name as a user already enrolled in OmniPass, the OmniPass import function will fail.OMNIPASS CONTROL CENTERThis section will serve to explain functions within the OmniPass Control Center that weren’t explained earlier. You can access the OmniPass Control Center any of three ways:■Double-click the golden OmniPass key shaped icon in the Windows taskbar (typically in the lower-right cor-ner of the desktop)■Click the Start button; select the Programs group; select the Softex program group; and click the OmniPass Control Center selection.■Open the Windows Control Panel (accessible via Start button --> Settings --> Control Panel) and double-click the Softex OmniPass icon.User ManagementThe User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/Export User functionality is documented in “Exporting and Importing Users” on page 119. Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard. The Enrollment Wizard is documented in “User Enrollment” on page 116. If you click Removes a user from OmniPass, OmniPass will prompt you to authenticate. Authenticate with the credentials (or enrolled fingerprint) of the user you wish to remove. OmniPass will prompt you to confirm user removal. Click OK to complete user removal.User SettingsThe User Settings tab has four interfaces: Audio Settings, Taskb a r Ti p s , and Enrollment. User settings allow users to customize OmniPass to suit their individual prefer-ences. Under User Settings (Audio Settings and Ta s kb ar Tips) you can set how OmniPass notifies the user of OmniPass events (e.g., successful login, access denied, You cannot import a user into OmniPass if there already is a user with the same name enrolled in OmniPass. Removing a user will automatically destroy all OmniPass data associated with that user. All identities and credentials associated with the user will be lost.If you are sure about removing the user, we recommend you export the user profile.T Series.book Page 120 Thursday, July 14, 2005 2:24 PM
121Using the Fingerprint Sensoretc.). The details of each setting under the Audio Settings and Tas k bar Tips interfaces are self-explana-tory.The Enrollment interface allows you to enroll finger-prints. For the procedure to enroll and authentication device refer to Chapter 2.3. To enroll additional finger-prints, click Enroll Authentication Device, and authen-ticate with OmniPass. Select the fingerprint recognition device in the Select Authentication Device screen (it should already be marked by a green check if you have a finger enrolled) and click Next.System SettingsThe OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon.The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass. This setting is appropriate for an office setting or any setting where users must enter a username and password to log into a computer. This is the default setting.With the second option, Manually log on to OmniPass at startup, OmniPass will prompt you to login once you have logged on to Windows.With the third option, Do not log on to OmniPass at startup, OmniPass will not prompt for a user to be logged on.You can manually log on to OmniPass by right-clicking the OmniPass taskbar icon and clicking Log in User from the right-click menu.TROUBLESHOOTINGYou cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and passwordCannot add Windows users to OmniPassIf you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local secu-rity settings. You can do this by going to Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Network Access: Sharing and Security Model for Local Accounts. The correct setting should be Classic - Local Users Authen-ticate as Themselves.Cannot add a User with a Blank Password to OmniPassIf you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the proce-dure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure.Click Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Accounts: Limit local account use of blank pass-words to console login only. This setting should be set to Disabled.Dialog appears after OmniPass authentication during Windows LogonAfter installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box.This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). This could happen for any of the following reasons:■Your Windows password has changed■Your Windows account has been disabledIf you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password.Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.T Series.book Page 121 Thursday, July 14, 2005 2:24 PM
122LifeBook T Series Tablet PC – Appendix BT Series.book Page 122 Thursday, July 14, 2005 2:24 PM
123IndexIndexAACadapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Anti-theft Lock Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . 35BBattery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . . 38dead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17lithium ion battery . . . . . . . . . . . . . . . . . . . . . . . . . . 43low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63, 64recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43warm-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44BIOSguide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36BluetoothWhere to Find Information . . . . . . . . . . . . . . . . . .111Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Built-in Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . 16Button Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23CCapsLock Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 18CD-ROMcare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Changing Tablet PC Button Functions . . . . . . . . . . . 24Click Me! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Closed Cover Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 11Cold-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . .16Conventions used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21DDC in connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9DC Output Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35DC Power Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .15, 35Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Display Panel Latch . . . . . . . . . . . . . . . . . . . . . . . . . . .11Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Drivers and Application Restore CD . . . . . . . . . . . . . 69EError Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67External Monitor Port . . . . . . . . . . . . . . . . . . . . . .15, 55FFingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . . 115enrolling a fingerprint . . . . . . . . . . . . . . . . . . . . . . 117getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . 115logging into a remembered site . . . . . . . . . . . . . . .118OmniPass authentication toolbar . . . . . . . . . . . . . 117password replacement . . . . . . . . . . . . . . . . . . . . . .117remembering a password . . . . . . . . . . . . . . . . . . .117uninstalling OmniPass . . . . . . . . . . . . . . . . . . . . . .116user enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . .116using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Flexible Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47eject lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Floppy Diskcare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Function KeyF10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22F3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22F4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22F5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22F6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22F7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22F8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22F9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22T Series.book Page 123 Thursday, July 14, 2005 2:24 PM
124LifeBook T Series Tablet PC - IndexFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Fn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22HHard Disk Driveaccess indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 9, 13, 55Hibernate Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39IInfrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Internal LAN Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54IrDA/FIR port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9KKeyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 21cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21LLAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15LifeBook Security Application Paneloperating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26LifeBook Security/Tablet PC Buttons . . . . . . . . . 11, 23LifeBook T Series Tablet PCspecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79LifeBook T Series Tablet PC specificationsadditional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81agency approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81display specifications . . . . . . . . . . . . . . . . . . . . . . . 79environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80physical specifications . . . . . . . . . . . . . . . . . 79, 80, 81power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Local Area Network (LAN) . . . . . . . . . . . . . . . . . . . . 10MMemorycapacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 45inserting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45upgrade module . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Memory Stickinstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 9, 12, 55microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79ModemproblemsTroubleshootingmodem 61modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 15Modem (RJ-11) Port . . . . . . . . . . . . . . . . . . . . . . . . . .15Modem Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54Modem Result Codes . . . . . . . . . . . . . . . . . . . . . . . . . .68Modular Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48Mouseproblems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60See TouchpadNNumeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21NumLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Ooptional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Additional Accessories . . . . . . . . . . . . . . . . . . . . . . . .8additional accessories . . . . . . . . . . . . . . . . . . . . . . . . .8carrying cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8docking options . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8power options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8storage options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8PPC Cardcare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13PC Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9PC Cardsremoving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11pencalibrating the pen . . . . . . . . . . . . . . . . . . . . . . . . . .31installing a pen tether . . . . . . . . . . . . . . . . . . . . . . . .30replacing the tip . . . . . . . . . . . . . . . . . . . . . . . . . . . .31using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Pen and Active Digitizer . . . . . . . . . . . . . . . . . . . . . . . .30pen tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53detaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53T Series.book Page 124 Thursday, July 14, 2005 2:24 PM
125Indexproblems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Port Replicator Connector . . . . . . . . . . . . . . . . . . . . . 16PowerAC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Auto/Airline adapter . . . . . . . . . . . . . . . . . . . . . . . .35failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62, 63indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35powerpower on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Power Management . . . . . . . . . . . . . . . . . . . . . . . .38, 39Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . .36, 67RRegistration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Re-Installing Individual Drivers and Applications . .69Removing a Memory Stick . . . . . . . . . . . . . . . . . . . . .50Restarting the system . . . . . . . . . . . . . . . . . . . . . . . . . . 39Restoring Your Pre-installed Software . . . . . . . . . . . .69RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 54Rotation Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12SScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18SD Cardremoving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50SD Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16, 45Secure Digital Cardremoving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Security Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Security lock slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Setting up LifeBook Security Panel . . . . . . . . . . . . . . . 24Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Smart Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . .49Smart Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . 12, 17Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Suspend/Resume Button . . . . . . . . . . . . . . .9, 11, 38, 52TTablet Dock port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Tablet PCcare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Touch Screenclicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32Touchpadclicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27control adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 28double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Touchpad Pointing Device . . . . . . . . . . . . . . . . . . 11, 27Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61mouse/keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62port replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65UUniversal Serial Bus Port . . . . . . . . . . . . . . . . . . . . . . . 54USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62USB 2.0ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15USB port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Using the Active Digitizer . . . . . . . . . . . . . . . . . . . . . .31Using the system as a Tablet . . . . . . . . . . . . . . . . . . . . 19Vvolume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29WWarm-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Start key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Wireless LANBefore Using the Wireless LAN . . . . . . . . . . . . . . . 96IP address information . . . . . . . . . . . . . . . . . . . . . 109Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 106Wireless LAN Glossary . . . . . . . . . . . . . . . . . . . . . 107Wireless LAN On-Off Switch . . . . . . . . . . . . . . . . . . . 10WLAN On/Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . 13T Series.book Page 125 Thursday, July 14, 2005 2:24 PM
126LifeBook T Series Tablet PC - IndexT Series.book Page 126 Thursday, July 14, 2005 2:24 PM
T Series.book Page 127 Thursday, July 14, 2005 2:24 PM
T Series.book Page 128 Thursday, July 14, 2005 2:24 PM
T Series.book Page 129 Thursday, July 14, 2005 2:24 PM
T Series.book Page 130 Thursday, July 14, 2005 2:24 PM

Navigation menu