Fujitsu Client Computing WB0063 533AN_HMW WLAN & EYTF3CSFT BT IN LIFEBOOK T SERIES User Manual Appendix H

Fujitsu Limited 533AN_HMW WLAN & EYTF3CSFT BT IN LIFEBOOK T SERIES Appendix H

Users Manual

                                                         FCC ID: EJE-WB0063  (IC: 337J-WB0063)                                                             EMC Technologies Pty Ltd – 176 Harrick Road, Keilor Park, VIC 3042 Australia www.emctech.com.au       APPENDIX H  USER MANUAL
  User’s GuideLearn how to use your Fujitsu LifeBook T2020 notebook
    Copyright and Trademark InformationFujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.Intel, Intel Core, Centrino, and Intel Centrino Pro are trademarks or registered trademarks of Intel Corporation or its subsidiaries in  the United States and other countries.Microsoft, Windows, Windows Vista, and OneNote are either registered trademarks or trademarks of Microsoft Corporation in the  United States and/or other countries.PCMCIA is a trademark of the Personal Computer Memory Card International Association.EverNote is a registered trademark of EverNote Corporation.Bluetooth is a trademark of Bluetooth SIG, Inc., USA.Google and Picasa are trademarks or registered trademarks of Google Incorporated.OmniPass is a trademark of Softex, Inc.Roxio is a trademark of Roxio, a division of Sonic Solutions.PowerProducer and PowerDVD are trademarks of CyberLink Corp.Adobe, Acrobat, and Acrobat Reader are either a registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.Norton and Norton Internet Security are trademarks or registered trademarks of Symantec Corporation in the United States and other countries.All other trademarks mentioned herein are the property of their respective owners.
© Copyright 2008 Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu.  B5FJ-DRAFT-01EN-00WARNINGHANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.DECLARATION OF CONFORMITYaccording to FCC Part 15Responsible Party Name: Fujitsu Computer Systems CorporationAddress:  1250 E. Arques Avenue, M/S 122Sunnyvale, CA 94085Telephone: (408) 746-6000Declares that product: Base Model Configuration:LifeBook T2020 notebookComplies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any interference received,  including interference that may cause undesired operation.
IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 16 VDC, with a current of 3.75 A (60 W).When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:•Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.•Avoid using a modem during an electrical storm. There may be a remote risk of electric shock from lightning.•Do not use a modem to report a gas leak in the vicinity of the leak.•Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.•To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord.•For TV tuner use: To protect from overvoltages and transients on the Cable Distribution System, make sure that the outer shield of the coaxial cable is connected to earth (grounded) at the building premise as close to the point of cable entrance as practicable, as required per NEC Article 820.93, ANSI/NFPA 70: 2005. If you have questions about your CATV installation, contact your service provider.SAVE THESE INSTRUCTIONSFor Authorized Repair Technicians Only System Disposal DANGER OF EXPLOSION IF LITHIUM (CLOCK) BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTION.FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH THE SAME TYPE AND RATING FUSE.+AC adapter output polarity:
Recycling your battery Over time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*. If you replace it, it is important that you dispose of the old battery properly because batteries contain materials that could cause environmental damage if disposed of improperly.Fujitsu is very concerned with environmental protection, and has enlisted the services of the Rechargeable Battery Recycling Corporation (RBRC)**, a non-profit public service organization dedicated to protecting our environment by recycling old batteries at no cost to you.RBRC has drop-off points at tens of thousands of locations throughout the United States and Canada. To find the location nearest you, go to www.RBRC.org or call 1-800-822-8837. If there are no convenient RBRC locations near you, you can also go to the EIA Consumer Education Initiative website (http://EIAE.org/) and search for a convenient disposal location.Remember – protecting the environment is a cooperative effort, and you should make every effort to protect it for current and future generations.*    To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site at www.shopfujitsu.com in the US or www.fujitsu.ca/products/notebooks in Canada.**   RBRC is an independent third party to which Fujitsu provides funding for battery recycling;   RBRC is in no way affiliated with Fujitsu.
    ContentsPrefaceAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Chapter 1 Getting to Know Your LifeBookOverview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Locating the Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Top Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Left-Side Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Right-Side Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Back Panel Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Bottom Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Status Indicator Panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Battery Level Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
 7 Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Opening the Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Using the System as a Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Adjusting Display Panel Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Using the Keyboard  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Quick Point Pointing Device/Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . 39Quick Point Control Adjustment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Clicking on Touch Screen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Right-Clicking on Touch Screen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Calibrating the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Installing a Pen Tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Controlling the Volume  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47LifeBook Security/Tablet PC Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Security Button Functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Pre-logon button functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Post-logon button functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Changing Tablet PC Button Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Setting up LifeBook Security Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Using Your LifeBook Security Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Uninstalling/Re-installing the Security Panel Application. . . . . . . . . . . . . 58
 8 Chapter 2 Getting Started with Your LifeBookPower Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Connecting the Power Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Starting Your LifeBook Notebook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Power On  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Boot Sequence  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Hard Disk Drive Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Booting the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Starting Windows Vista the first time  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Starting Windows XP the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Registering Your LifeBook notebook with Fujitsu  . . . . . . . . . . . . . . . . . . 69Installing ClickMe!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Fujitsu Driver Update Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Power/Suspend/Resume Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Standby (Sleep) Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Hibernation (Save-to-Disk) Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Windows Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Restarting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Powering Off  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Chapter 3 User-Installable FeaturesLithium ion Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Recharging the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Memory Stick/Secure Digital Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Installing/Removing Memory Stick/SD Cards. . . . . . . . . . . . . . . . . . . . . . 82
 9 PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Installing PC Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Smart Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Memory Upgrade Module  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Installing Memory Upgrade Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Removing a Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Checking the Memory Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Internal LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Port Replicator Connector  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90IEEE 1394 Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Microphone Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92External Video Port  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Chapter 4 Troubleshooting Your LifeBookTroubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Identifying the Problem  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Power On Self Test Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Restoring Your Pre-installed Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113Re-installing Individual Drivers and Applications. . . . . . . . . . . . . . . . . . . 113Restoring the Operating System for Windows XP Systems. . . . . . . . . . . . 114Restoring the Operating System for Windows Vista Systems . . . . . . . . . . 116Automatically Downloading Driver Updates . . . . . . . . . . . . . . . . . . . . . . . 119
 10 Chapter 5 Care and MaintenanceCaring for your LifeBook Notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Cleaning your LifeBook notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123Storing your LifeBook notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123Traveling with your LifeBook notebook  . . . . . . . . . . . . . . . . . . . . . . . . . . 123Batteries  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127Chapter 6 System SpecificationsSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129Chipset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129Audio  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Mass Storage Device Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132Power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133Popular Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134Pre-Installed Software  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134Learning About Your Software  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
 11 Glossary/RegulatoryGlossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154Appendix A: WLAN User’s GuideBefore Using the Optional Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . 162Wireless LAN Device Covered by this Document. . . . . . . . . . . . . . . . . . . 162Characteristics of the WLAN Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162Wireless LAN Modes Using this Device . . . . . . . . . . . . . . . . . . . . . . . . . . 163Deactivating/Disconnecting the WLAN Device  . . . . . . . . . . . . . . . . . . . . 165Deactivation Using the Wireless On/Off Switch . . . . . . . . . . . . . . . . . . . . 166Disconnection Using the Icon in the Taskbar. . . . . . . . . . . . . . . . . . . . . . . 166Activating the WLAN Device  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166Configuring the Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167Configuring the WLAN Using Windows Vista . . . . . . . . . . . . . . . . . . . . . 167Configuring the WLAN Using Windows XP  . . . . . . . . . . . . . . . . . . . . . . 168Connection to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168Troubleshooting the WLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169WLAN Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Using the Bluetooth Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173What is Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Where to Find Information About Bluetooth . . . . . . . . . . . . . . . . . . . . . . . 173
 12 Appendix B: Fingerprint Sensor DeviceIntroducing the Fingerprint Sensor Device  . . . . . . . . . . . . . . . . . . . . . . . . 175Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176Installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176User Enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Configuring OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188OmniPass Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
13     PrefaceAbout This GuideThe LifeBook T2020 notebook from Fujitsu Computer Systems Corporation is a powerful convertible computer. It can be used either as a standard notebook using keyboard input, or in tablet configuration using pen input. It is powered by a fast, Intel® Core™ 2 Duo Ultra Low Voltage processor, has a built-in color display with an active digitizer, and brings the computing power of desktop personal computers (PCs) to a portable and versatile environment.This manual explains how to operate your LifeBook T2020 notebook’s hardware and pre-installed system software. Your LifeBook T2020 notebook comes with Windows® XP Tablet PC Edition 2005 or Windows Vista™ Business pre-installed.Conventions Used in the GuideKeyboard and on-screen keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].Pages with additional information about a specific topic are cross-referenced within the text. For example: (“See Installation Procedure on page 43”.) Note that all cross-references are linked to the referenced items, so by clicking the link, you will automatically go to the referenced item or page.On-screen menu items appear in bold. Example: “Click Fujitsu Menu, and select your choice”.
14 - About This GuideFujitsu Contact InformationService and Support You can contact Fujitsu Service and Support in the following ways:•Toll free: 1-800-8Fujitsu (1-800-838-5487)•E-mail: 8fujitsu@us.fujitsu.com •Website: http://www.computers.us.fujitsu.com/supportBefore you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:•Product name•Product configuration number•Product serial numberTHE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF THE SUBJECT MATERIAL.THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATION CAREFULLY.THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR LIFEBOOK NOTEBOOK, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.
15 - About This Guide•Purchase date•Conditions under which the problem occurred•Any error messages that have occurred•Type of device connected, if anyFujitsu Shopping Online You can go directly to the online by going to the website at: www.shopfujitsu.com.Limited Warranty Your LifeBook T2020 notebook is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your notebook for the Limited Warranty period and terms and conditions.YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS.
16     Chapter 1    Getting to Know Your LifeBookOverviewThis section describes the components of your Fujitsu LifeBook T2020 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers.Figure 1.  Fujitsu LifeBook T2020 notebook
17 - Locating the Controls and ConnectorsLocating the Controls and ConnectorsConnectors and peripheral interfaces on the LifeBook T2020 notebook and the optional port replicator allow you to connect a variety of devices. Specific locations are illustrated in Figures 2 through 6. The table below provides a short description of each icon on the LifeBook T2020 notebook and/or optional port replicator. Each of the icons is either molded into or printed on the notebook or port replicator chassis.Connection Notebook Icon PurposeDC in connector Connect an external power source such as the AC adapter or auto/airline adapter. SD/Memory Stick SlotThe Secure Digital (SD) card/Memory Stick slot allows you to insert a flash memory card for data storage. Flash memory cards allow you to transfer data to and from a variety of different digital devices.Smart Card Slot A dedicated Smart Card slot allows you to insert a Smart Card on which you can store such data as medical information or electronic “cash”. USB Port Connect Universal Serial Bus 2.0 or 1.1 compliant devices to the  notebook.PCMCIA  Card slot Insert Type I or Type II PC Cards.Microphone Jack Connect an external microphone. The internal microphone is disabled when you plug in an external microphone. Headphone Jack Connect stereo headphones or powered external speakers. The internal speaker is disabled when you plug in external headphones or powered speakers.
18 - Locating the Controls and ConnectorsDock port Connect the notebook port replicator or other approved docking device. Refer to documentation accompanying the dock for more information.Security lock slot The security slot allows you to secure the notebook using compatible locking devices.Suspend/ Resume buttonThe Suspend/Resume button allows you to suspend notebook activity without powering off, resume your notebook from suspend mode, and power on the system when it has been shut down from Windows. Local Area Network (LAN)The LAN (RJ-45) jack is used to connect the internal 10/100/1000* Base-T/Tx Ethernet to a Local Area Network (LAN) in your office or home, or broadband devices such as a cable modem, DSL, or satellite Internet. *1000 Mbps, commonly referred to as Gigabit Ethernet.Wireless LAN  On-Off SwitchThe wireless LAN switch allows you to turn power to the optional wireless LAN device on and off.External Video portThe external video port allows you to connect an external monitor or LCD projector to your computer.Digital Video InterfaceThe DVI-D port on the optional port replicator allows you to connect a flat-panel LCD monitor or television that is equipped with a DVI-D port for ultra-crisp digital images and graphics.Connection Notebook Icon Purpose
19 - Locating the Controls and ConnectorsFigure 2.  LifeBook notebook with display openDisplay PanelStatus  SpeakerKeyboardLifeBook Security/Power/Suspend/Tablet PC ButtonsResume ButtonMemory Stick/SDQuick Point Cursor ControlIndicator PanelRight ButtonScroll ButtonCard SlotBuilt-inMicrophonesFingerprint SensorLeft Button
20 - Locating the Controls and ConnectorsTop ComponentsThe following is a brief description of your LifeBook notebook’s top components. Display Panel The display panel is a color LED panel with backlighting for the display of text and graphics and active digitizer functionality. Status Indicator Panel The Status Indicator Panel displays symbols that correspond with a specific component of your LifeBook notebook. See “Status Indicator Panel” on page 30.LifeBook Security/Tablet PC Buttons The LifeBook Security/Tablet PC Buttons provide password security for your system, as well as one-touch application launch capability. See “LifeBook Security/Tablet PC Buttons” on page 49.Power/Suspend/Resume Button The Power/Suspend/Resume button allows you to suspend notebook activity without powering off, resume your LifeBook notebook from standby mode, and power on your notebook when it has been shut down from Windows. See “Power/Suspend/Resume Button” on page 72.Keyboard A full-size keyboard with dedicated Windows keys. See “Keyboard” on page 37.Right Button This button acts the same as the right button on a mouse.Speaker The built-in speaker allows for mono sound.
21 - Locating the Controls and ConnectorsScroll Button The scroll button is used in conjunction with the Quick Point cursor control to navigate through pages quickly and easily.Left Button This button acts the same as the left button on a mouse.Memory Stick/SD Card Slot The Memory Stick/SD card slot allows you to install a Memory Stick or a Secure Digital (SD) card for data storage. This architecture allows you to transfer data from a variety of different digital devices. See “Installing Memory Stick/SD Cards” on page 83.Quick Point Cursor Control The Quick Point control offers an additional method for moving the cursor. See “Quick Point Pointing Device/Touch Screen” on page 40.Dual Built-in Microphones The built-in microphones allows you to input stereo audio. Fingerprint Sensor The fingerprint sensor device allows you to log onto your system and password-protected websites and applications by swiping your finger over the sensor. See “Introducing the Fingerprint Sensor Device” on page 176.
22 - Locating the Controls and ConnectorsFigure 3.  LifeBook notebook left-side panelLeft-Side Panel ComponentsThe following is a brief description of your LifeBook notebook’s left-side components. PC Card Slot The PC Card Slot allows you to install a Type I or Type II PC Card. See “PC Cards” on page 84.Wireless LAN/Bluetooth On/Off Switch The wireless LAN/Bluetooth on/off switch is used to turn on and off the optional WLAN and Bluetooth devices. Switching the device off when not in use will help to extend battery life. See “Activating the WLAN Device” on page 167.PC Card Eject Button The PC Card eject button is used for removing a PC Card from the slot.Air VentsPC Card SlotSmart Card Slot PC Card Eject ButtonWireless LAN/Bluetooth On/Off Switch
23 - Locating the Controls and ConnectorsSmart Card Slot A dedicated Smart Card slot is provided on your notebook. Smart Cards are the same size and shape as credit cards, but they contain an integrated microprocessor chip. See “Smart Card Reader” on page 86. In order to use the embedded Smart Card Reader, you must purchase optional third-party software for installation.Air Vents The air vents are used to cool the system to prevent overheating.TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE PERFORMANCE, BE SURE TO KEEP ALL AIR ALL VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. DO NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.
24 - Locating the Controls and ConnectorsFigure 4.   LifeBook notebook right-side panel Right-Side Panel ComponentsThe following is a brief description of your LifeBook notebook’s right-side components. Headphone Jack The headphone jack allows you to connect headphones. See “Headphone Jack” on page 93. USB 2.0 Ports The USB 2.0 ports (one on the right side, one on the rear) allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480 Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 12 Mbps. See “Universal Serial Bus Ports” on page 91.DC Power Jack The DC power jack allows you to plug in the AC adapter to power your LifeBook notebook and charge the internal Lithium ion battery.Pen/Pen Holder Microphone Headphone JackDC Power JackIEEE 1394 JackUSB 2.0 PortJackPen Tether Point
25 - Locating the Controls and ConnectorsIEEE 1394 (4-pin) Jack The 4-pin 1394 jack is used to connect between your notebook and an IEEE 1394 peripheral such as a digital video camera. See “IEEE 1394 Port” on page 92.Microphone Jack The microphone jack allows you to connect an external mono microphone. See “Microphone Jack” on page 93.Pen Tether Attachment Point The pen tether attachment point is designed to securely hold a pen tether to prevent loss of the pen. See “Installing a Pen Tether” on page 47 for additional information.Pen/Pen Holder The pen is used as the interface with the active digitizer display.
26 - Locating the Controls and ConnectorsFigure 5.  LifeBook notebook back panelBack Panel ComponentsFollowing is a brief description of your LifeBook notebook’s back panel components. Gigabit LAN (RJ-45) Jack The internal LAN (RJ-45) jack is used for an internal Gigabit (10Base-T/100Base-Tx/1000Base-T) Ethernet LAN connection. See “Internal LAN (RJ-45) Jack” on page 90.USB 2.0 Ports The USB 2.0 ports allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 12Mbps. See “Universal Serial Bus Ports” on page 91.Gigabit LAN (RJ-45) JackUSB 2.0 PortAnti-Theft Lock SlotAir VentsExternal Video Port
27 - Locating the Controls and ConnectorsAir Vents The air vents allow air to circulate through the system to cool down the components. Anti-theft Lock Slot The anti-theft lock slot allows you to attach an optional physical lock down device. External Video Port The external monitor port allows you to connect an external monitor or LCD projector. See “External Video Port” on page 93.TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE PERFORMANCE, BE SURE TO KEEP ALL AIR ALL VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. DO NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.
28 - Locating the Controls and ConnectorsFigure 6.  LifeBook notebook bottom panelBottom ComponentsThe following is a brief description of your LifeBook notebook’s bottom panel components. Battery Latches The battery latches are used to secure the Lithium ion battery in the battery bay.Lithium ion Battery Bay The battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery. See “Lithium ion Battery” on page 77.Memory Upgrade CompartmentLithium ionPort Replicator ConnectorBattery BayAir VentsBattery Latches
29 - Locating the Controls and ConnectorsAir Vents The air vents allow air to circulate through the system to cool down the components. Memory Upgrade Compartment Your notebook comes with high speed Double Data Rate 2 Synchronous Dynamic RAM (DDR2 SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your notebook, thus improving overall performance. See “Memory Upgrade Module” on page 87. Under normal circumstances, it should not be necessary to open this compartment.Port Replicator Connector This connector allows you to connect the optional Port Replicator to your notebook. TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE, BE SURE TO KEEP ALL AIR ALL VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED. DO NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.
30 - Status Indicator PanelFigure 7.  Status Indicator PanelStatus Indicator PanelThe Status Indicator displays symbols that correspond to a specific component of your Fujitsu LifeBook notebook. These symbols tell you how each of those components is operating.(Figure 7)  Battery Level IndicatorThe Battery Level indicators display the charge level of the indicated battery pack, as follows:•Green, solid: Battery is between 50% and 100% charged.•Orange, solid: Battery is between 13% and 49% charged.•Red, solid: Battery is between 0% and 12% charged.•Orange, blinking: Blinks during battery status measurement (Four seconds after the battery is installed).•Red, blinking: There is a problem with the battery.•Off: There is no battery installed.Hard Drive AccessNumLkCapsLkScrLkSecurity Battery Level
31 - Status Indicator Panel Hard Drive Access IndicatorThe Hard Drive Access indicator shows whether your internal hard drive is being accessed. NumLk IndicatorThe NumLk indicator states that the integral keyboard is set in ten-key numeric keypad mode.  CapsLock IndicatorThe CapsLock indicator states that your keyboard is set to type in all capital letters.  ScrLk IndicatorThe ScrLk indicator states that your scroll lock is active.  Security IndicatorThe Security Indicator flashes (if a password was set) when the system resumes from Off or Standby mode. You must enter the password that was set in the Security Panel before you can resume operation.• If the battery pack is installed while the power is turned off, the battery level indicator will display the charge level for five seconds after it blinks orange.•If the AC adapter is not connected or the battery pack is not fully charged when the computer is switched to standby mode, the indicator will blink. The LED blinks at the rate of one second on/five seconds off. •Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged.•A shorted battery is damaged and must be replaced.
32 - Display PanelFigure 8.  Opening the Display PanelDisplay PanelYour LifeBook T2020 notebook contains an LED display panel that is backlit for easier viewing in bright environments. The convertible design of your notebook allows you to open the display fully, rotate it in either direction 180 degrees, and lay it face up on the keyboard. This allows you to use the system as a tablet, much as you would a pad of paper.
33 - Display PanelOpening the Display PanelLift the display backwards, being careful not to touch the screen with your fingers, until it is at a comfortable viewing angle. (Figure 8)Using the System as a TabletIf you would like to use the system as a tablet, perform the following steps. 1Lift the display until it is perpendicular to the keyboard. (Figure 9).2When the display is perpendicular to the keyboard, rotate it 180 degrees in either direction (Figure 10) so that it is facing backwards.3Holding the top edge of the display panel, pull it forward until it is lying nearly atop the keyboard.4Lay the display flush against the system so that the latch engages. You can now use your system as a tablet. (Figure 11)To return the system to notebook configuration, repeat step 3 and 2.•The display can be rotated in either direction, but when returning the system to notebook mode, be sure to turn it back to its original position (i.e., the reverse of how you turned it when you opened it. Turning the display in the incorrect direction could cause hinge damage.•In the following step, be sure to position the display perpendicular to the keyboard, otherwise the keyboard or display cover could get scratched.
34 - Display PanelHolding the Tablet PC Your computer can be used in tablet configuration in three different orientations (Figure 11). •Portrait Orientation: Hold the system with the display positioned vertically with the latch on the left.•2nd Portrait Orientation: Hold the system with the display positioned vertically with the latch on the right.•Landscape Orientation: Hold the system with the display positioned horizontally with the latch on the top.Note: Holding the system horizontally with the latch at the bottom is not a functional orientation.Figure 9.  Fully Open Display Figure 10.  Rotating Display Figure 11.  Tablet Mode
35 - Display PanelAdjusting Display Panel BrightnessOnce you have turned on your Tablet PC, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are three ways to adjust the brightness: keyboard, power management utility, and Fujitsu Menu. Using Keyboard to Adjust Brightness Adjusting the brightness using the keyboard changes the system setting (i.e., the settings you make via the function keys automatically changes the brightness settings in the system’s Pen and Tablet Settings). •[Fn+F6]: Pressing repeatedly will lower the brightness of your display.•[Fn+F7]: Pressing repeatedly will increase the brightness of the display.Using Power Management to Adjust Brightness To adjust brightness with the power management utility,:Windows XP: Click Start -> Control Panel. If you are not in Classic View, select it in the left panel. Double-click the Tablet and Pen Settings icon, then select the Display tab. Set the screen brightness slider for When plugged in and Powered by batteries scenarios.Windows Vista: Click Start -> Control Panel. If you are not in Classic View, select it in the left panel. Double-click the Windows Mobility Center icon, then double-click the icon adjacent to Display brightness. Set the screen brightness sliders for On battery and Plugged in scenarios.Using the Fujitsu Menu to Adjust Brightness Windows XP: To adjust brightness using the Fujitsu menu, click on the Fujitsu Menu icon in the system tray in the lower right corner of the screen. From the menu that appears, select Brightness Control. The Tablet and Pen Settings window will open. Select the Display tab and set the screen brightness slider for battery and AC power scenarios.
36 - Display PanelWindows Vista: To adjust brightness using the Fujitsu menu, click on the Fujitsu Menu icon in the system tray in the lower right corner of the screen. Double-click Windows Mobility Center, then double-click the icon adjacent to Display brightness. Set the screen brightness sliders for On battery and Plugged in scenarios.IF USING AC POWER, YOUR BRIGHTNESS SETTING IS SET TO ITS HIGHEST LEVEL BY DEFAULT. IF USING BATTERY POWER, YOUR BRIGHTNESS SETTINGS IS SET TO APPROXIMATELY MID-LEVEL BY DEFAULT.THE HIGHER THE BRIGHTNESS LEVEL, THE MORE POWER THE TABLET PC WILL CONSUME AND THE FASTER YOUR BATTERIES WILL DISCHARGE. FOR MAXIMUM BATTERY LIFE, MAKE SURE THAT THE BRIGHTNESS IS SET AS LOW AS POSSIBLE.
37 - KeyboardKeyboardFigure 12.  KeyboardUsing the KeyboardYour Fujitsu LifeBook notebook has an integral 84-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys (Figure 12):EndHomeFn Key Start KeyFunction KeysNumeric Keypad Application Key Cursor Keys(surrounded by heavy line)
38 - Keyboard•Numeric keypad: Your notebook allows certain keys to serve dual purposes, both as standard characters and as numeric and mathematical keys. The ability to toggle between the standard character and numerical keys is controlled through the [NumLk] key.•Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. •Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. •Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.Numeric Keypad Certain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] keys. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary functions. Windows Keys Your LifeBook notebook has two Windows keys, consisting of a Start key and an Application key. The Start key displays the Start menu. This button functions the same as your onscreen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows documentation for additional information regarding the Windows keys.) Cursor Keys The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right).
39 - KeyboardFunction Keys Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. •The [Fn] key provides extended functions for the notebook and is always used in conjunction with another key. •[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.•[Fn+F4]: Pressing [F4] while holding [Fn] will toggle the Quick Point feature on and off. Note that the [Fn+F4] combination only works if Manual Setting is selected in the BIOS. (See “BIOS Setup Utility” on page 66)•[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.•[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.•[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your LifeBook notebook.•[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your LifeBook notebook.•[Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, external monitor only, and both built-in display panel and external monitor.
40 - Quick Point Pointing Device/Touch ScreenQuick Point Pointing Device/Touch ScreenFigure 13.  Touchpad pointing deviceThe Quick Point is built into your LifeBook notebook. It is used to control the movement of the cursor to select items on your display panel. The Quick Point is composed of a cursor control at the center of the keyboard and three buttons on the palm rest of your computer. The cursor control works the same way a mouse ball does, and moves the cursor around the display. It only requires light pressure with the tip of your finger, and the more pressure you use, the faster the cursor will move. The left button functions the same as a left mouse button while the right button has the same function as a right mouse button. When used with the cursor control, the middle button allows you to scroll up and down a screen. The actual functionality of the buttons may vary depending on the application that is being used.Left ButtonRight ButtonScroll ButtonQuick Point Control
41 - Quick Point Pointing Device/Touch ScreenClickingClicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the cursor to the item you wish to select, press the bottom button once, and then immediately release it. Double-ClickingDouble-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press and release the left button twice.•IF THE INTERVAL BETWEEN CLICKS IS TOO LONG, THE DOUBLE-CLICK WILL NOT BE EXECUTED.•PARAMETERS FOR THE QUICK POINT CAN BE ADJUSTED FROM THE MOUSE DIALOG BOX LOCATED IN THE WINDOWS CONTROL PANEL.
42 - Quick Point Pointing Device/Touch ScreenDraggingDragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it.ScrollingUsing the Scrolling button allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navigating through on-line pages. To scroll, press and hold the center button while scrolling with the cursor control button.
43 - Quick Point Pointing Device/Touch ScreenQuick Point Control AdjustmentThe Windows Control Panel allows you to customize your Quick Point with selections made from within the Mouse Properties dialog box. There are three aspects of Quick Point operation, which you can adjust:•Buttons: This tab lets you set up the buttons for right or left handed operation, in addition to setting up the time interval allowed between clicks in double-clicking.•Pointers: This tab lets you set up the scheme for the cursor depending on its functionality.•Pointer Options: This tab lets you set up a relation between the speed of your finger motion and the speed of the cursor. It also allows you to enable a Pointer Trail for the cursor arrow. Touch ScreenThe integrated Touch Screen allows you to use the included stylus as a pointing device. You can use the stylus to click, double-click, drag items and icons, or to draw like a pen or pencil in applications that support this behavior, such as drawing or painting programs. See the documentation that came with your application for details.•DO NOT USE EXCESSIVE FORCE WHEN TAPPING OR WRITING ON THE SCREEN WITH THE STYLUS. EXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR TOUCH SCREEN.•TO PURCHASE ADDITIONAL OR REPLACEMENT STYLUSES, VISIT FUJITSU’S ACCESSORIES WEBSITE AT: WWW.SHOPFUJITSU.COM.
44 - Quick Point Pointing Device/Touch ScreenClicking on Touch ScreenTo left-click, touch the object you wish to select and then lift the stylus tip immediately. Right-Clicking on Touch ScreenWindows VistaRight-click can be accomplished by holding the pen down until a circular icon appears. To change the settings for the right-click feature, go to Start -> Control Panel -> Pen and Input Devices. In the Pen Options tab, select “Press and Hold” then click the [Settings] button.Windows XP Tablet PC Edition:Right-click can be accomplished by holding the pen down until a circular icon appears. To change the settings for the right-click feature, go to Start -> Control Panel -> Tablet and Pen Settings. In the Pen Options tab, select “Press and Hold” then click the [Settings] button.
45 - Quick Point Pointing Device/Touch ScreenCalibrating the Touch ScreenIn order to ensure accurate tracking between the stylus and cursor, you must run the Touch Screen Calibration Utility before you use the Touch Screen for the first time, or after you change the display resolution.Double-ClickingTo double-click, touch the item twice, and then immediately remove the stylus tip. DraggingDragging means moving an item with the stylus by touching the screen, moving and then lifting the stylus. To drag, touch the Touch Screen with your stylus on the item you wish to move. While continuing to touch the screen with the stylus, drag the item to its new location by moving the stylus across the screen, and then lifting the stylus to release it. Dragging can also be done using your fingertip.
46 - Quick Point Pointing Device/Touch ScreenTo run the calibration utility:1Go to Start -> Control Panel. If you are not in Classic View, select “Switch to Classic View” in the left panel. Windows XP Tablet PC Edition: Double-click the Tablet and Pen Settings icon and select the Settings tab. Windows Vista: Double-click the Tablet PC Settings icon and select the General tab2Click the [Calibrate] button.3Adjust the display of your notebook to a comfortable angle and find the (+) symbol in the upper-left corner of the display.4Using the stylus, firmly touch the screen directly on the (+) symbol. Lift the stylus from the screen and the target will move to a different location on the screen.5Repeat step 4 until you have selected all of the (+) symbols.6Once you have selected all the symbols, press the [OK] button. 7Touch the stylus to various points on the screen to verify that the screen is correctly calibrated. If you are not satisfied with the screen’s calibration, press the [Calibrate]) button to begin again.DO NOT USE EXCESSIVE FORCE WHEN TAPPING ON THE SCREEN DURING CALIBRATION. USE OF EXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR TOUCH PANEL.WHEN USING THE STYLUS TO CALIBRATE THE SCREEN, BE SURE TO AVOID TOUCHING THE SCREEN WITH YOUR FINGERS; DOING SO COULD RESULT IN FAULTY CALIBRATION.
47 - Quick Point Pointing Device/Touch Screen2Attach the end of the pen tether with the larger loop to the attachment point on your tablet. To do so, insert the end of the pen tether through the attachment point, then feed the pen through the large loop in the tether.Installing a Pen TetherTo prevent dropping or losing your pen, you should attach it to your system using the pen tether that is included with the system. To attach the pen tether to your notebook, perform the following steps:1Attach the end of the pen tether with the smaller loop to your pen. To do so, push the end of the tether through the hole in the pen, then thread the opposite end of the tether through the loop.
48 - Volume ControlVolume ControlYour Fujitsu LifeBook notebook has multiple volume controls which interact with each other. Controlling the VolumeThe volume can be controlled in several different ways:•Volume can be changed or muted from within the Volume Control in the system tray.•Volume can be controlled with the F8 and F9 functions keys. Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your notebook. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your notebook.•Volume can be muted by pressing the [F3] key while holding down the [Fn] key. To restore audio, repeat the [Fn+F3] procedure.•Volume can be controlled by many volume controls that are set within individual applications.•Certain external audio devices you might connect to your system may have hardware volume controls.Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources. We recommend that you experiment with the various volume controls to discover the optimal sound level.ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF, YOU WILL OVERRIDE THE EXTERNAL VOLUME CONTROL SETTING.
49 - LifeBook Security/Tablet PC ButtonsFigure 14.   LifeBook T2020 Notebook Security/Tablet PC Buttons LifeBook Security/Tablet PC ButtonsA unique feature of your LifeBook T2020 notebook is the array of Security and Tablet PC buttons. These buttons allow you to secure your notebook from unauthorized use and to launch specific applications and functions with the touch of a button. Security Button FunctionsIf the security system is activated, upon starting your notebook or resuming from Standby, Hibernate, or shutdown mode, the security system will require you to enter a password code using the security buttons. After you enter the correct password, your system will resume operation. The five security/Tablet PC buttons are located on the bottom right-hand side of the display when it is configured to be used as a notebook. All five buttons are used when implementing security functions. Four of the buttons are used to enter the password, and the fifth is used as an Enter button. See Table 1 for information about each of the Security buttons.ABn1234ENT
50 - LifeBook Security/Tablet PC ButtonsPre-logon button functionsAll five buttons can be used before logging on to Windows (i.e., the Windows logon screen is displayed). Three of the buttons have secondary functions. See Table 2 for information about the pre-logon functions.<Tab>/<Shift><Tab> When you press the [Page Down] button when the system is pre-logon, each press of the button will act as if you had pressed the [Tab] key.When you press the [Fn] button then press and release the [Page Down] button, each press of the button will act as if you had pressed the [Shift]+[Tab] key combination.<Enter>/<Escape> When you press the [Page Up] button when the system is pre-logon, each press of the button will act as if you had pressed the [Enter] key.Table 1.  Security Panel Button FunctionsButton Icon  System State Security Panel FunctionSystem is pre-boot or resuming from suspend Security Button 1Security Button 2Security Button 3Security Button 4Security Enter Button
51 - LifeBook Security/Tablet PC ButtonsTable 2.  Pre-logon Tablet PC Button FunctionsWhen you press the [Fn] button then press and release the [Page Up] button, each press of the button will act as if you had pressed the [Escape] key.Screen Rotation The screen rotation feature would normally be used when the system is configured as a tablet. When you would like to use the tablet as an eBook, for example, you would use the portrait orientation; when accessing spreadsheets or using the system as a notebook, you would more typically use landscape orientation.When the system is changed to tablet configuration, the orientation automatically changes to portrait mode by default.Button Icon  System State Notebook Function Secondary Functions(Fn + Button)System is pre-logon (Windows logon screen is displayed) <Tab> <Shift><Tab><Enter> <Escape>Rotate screen NoneUsed to invoke  secondary functionNoneCtl+Alt+Del Button None
52 - LifeBook Security/Tablet PC Buttons When you press the [Screen Rotation] button when the system is in pre-boot, the system screen orientation changes from portrait (vertical) to landscape (horizontal) or from landscape to portrait.Table 3.  Post-logon Tablet PC Button FunctionsTHE SCREEN ORIENTATION DEFAULT CAN BE CHANGED BY GOING TO THE CONTROL PANEL AND DOUBLE-CLICKING ON THE FUJITSU TABLET CONTROLS ICON AND SELECTING THE DESIRED SETTINGS IN THE DISPLAY PROPERTIES. AFTER CHANGING THE SETTINGS, SAVE THEM IN FUJITSU TABLET CONTROLS.Button Icon  System State Primary Notebook  FunctionSecondary Functions (Fn + Button)System is post-logon (Windows desktop is displayed) Page Down User-defined Application A (Default = Calculator)Page Up User-Defined Application B (Default = MS Journal)Screen Rotation Display Switching:1. LED only2. CRT only3. Dual DisplaySecondary  Function SelectionFujitsu Menu UtilityCtl+Alt+Del Button None
53 - LifeBook Security/Tablet PC ButtonsFunction / Fujitsu Menu Utility Button The [Function] button works in conjunction with the other application buttons to provide additional functionality for the buttons. Refer to specific details above.Post-logon button functionsAll five buttons can be used after logging on to Windows. Four of the buttons have secondary functions. See Table 3 for information about each of the post-logon functions.Page Down / Application A Button When you press the [Page Down] button when the system is running, each press of the button will scroll the screen down one frame. This allows you to navigate quickly through large documents.When you press the [Fn] button then press and release the [Page Down/Application A] button, you will automatically start whichever program is assigned to the button. The default application for this button is Calculator. See “Changing Tablet PC Button Functions” on page 54 to select a different application for this button.Page Up / Application B Button When you press the [Page Up] button when the system is running, each press of the button will scroll the screen up one frame. This allows you to navigate quickly through large documents.When you press the [Fn] button then press and release the [Page Up/Application B] button, you will automatically start whichever program is assigned to the button. The default application for this button is Microsoft Journal. See “Changing Tablet PC Button Functions” on page 54. to select a different application for this button.Screen Rotation /Display Switching Button The screen rotation feature would normally be used only when the system is configured as a tablet. When you would like to use the tablet as an eBook, for example, you would use the portrait orientation; when accessing spreadsheets or using the system as a notebook, you would more typically use landscape orientation.
54 - LifeBook Security/Tablet PC ButtonsWhen the system is changed to tablet configuration, the orientation automatically changes to portrait mode by default. When you press the [Screen Rotation /Display Switching] button, the system screen orientation changes from portrait (vertical) to landscape (horizontal) or from landscape to portrait. Pressing the [Fn] button while pressing the [Screen Rotation] button will switch the display output in the following order: built-in display only, external display only, dual display.Function / Fujitsu Menu Utility Button The [Function] button works in conjunction with the other application buttons to provide additional functionality for the buttons. Refer to specific details above.Pressing the [Fn] button twice in succession causes the Fujitsu Menu Utility to appear on your screen, allowing you to modify certain system settings.Ctl+Alt+Del Button Pressing and holding the [Ctl-Alt-Del] button for up to 750 milliseconds launches the Logon screen or the Windows Task Manager.Changing Tablet PC Button FunctionsThe Application A and B buttons can be changed to launch a program or perform an action you select. By default, the Application A button launches the Calculator, and the Application B button launches MS Journal.To launch different applications or cause the Application A or B buttons to perform a specific action:THE SCREEN ORIENTATION DEFAULT CAN BE CHANGED BY GOING TO THE CONTROL PANEL AND DOUBLE-CLICKING ON THE FUJITSU TABLET CONTROLS ICON AND SELECTING THE DESIRED SETTINGS IN THE DISPLAY PROPERTIES. AFTER CHANGING THE SETTINGS, SAVE THEM IN FUJITSU TABLET CONTROLS.
55 - LifeBook Security/Tablet PC ButtonsWindows XP:1Double-click on the Tablet and Pen Settings icon in the Control Panel. 2Select the Tablet Buttons tab and select the button you would like to change from the list.3Click [Change] and open the drop down list in the Action: field.4Select the action you would like the button to perform. If you want to launch a program, click on Launch an Application then browse to the location of the program.5Click [OK], then click [OK] again. The buttons will now perform the actions you have assigned to them. Windows Vista:1Double-click on the Tablet PC Settings icon in the Control Panel. 2Select the Buttons tab and select the button you would like to change from the list.3Click [Change] and open the drop down list in the Press: field.4Select the action you would like the button to perform. If you want to launch a program, click on Launch an Application then browse to the location of the program.5Click [OK], then click [OK] again. The buttons will now perform the actions you have assigned to them.Setting up LifeBook Security PanelWhen you receive your notebook, the security panel application is pre-installed without any passwords. The following sections provide detailed information on your security panel, how to set, change or remove passwords.Numbered Buttons Use these buttons to enter your password.Enter Button After entering the button strokes, push this button to enter the password into the notebook.
56 - LifeBook Security/Tablet PC ButtonsPasswordsThe user and supervisor password may be set on this notebook. A supervisor password is typically the same for all tablets and notebooks in a work group, office, or company to allow for system management. Individual computers in a group environment should not use a common password. A password consists of one to five button strokes plus the enter button. A valid stroke consists of pushing one or up to four buttons simultaneously. The following are valid button strokes: •Pushing [4] by itself•Pushing [2] and [3] at the same time•Pushing [1], [2], and [4] at the same time•Pushing [1], [2], [3], and [4] at the same timeThe following are valid passwords. The numbers within braces ({  }) are button strokes using more than one button. •{[2]+[3]}, [1], [Enter]•[4], [enter]•{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]Setting Passwords When shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the supervisor password before the user password. •THE PURPOSE OF SUPERVISOR PASSWORD IS TO BE ABLE TO BYPASS THE USER PASSWORD IN CASE THE USER PASSWORD IS FORGOTTEN. THE SUPERVISOR PASSWORD ALONE WILL NOT LOCK THE SYSTEM.•YOU MUST SET THE SUPERVISOR AND USER PASSWORDS FOR THE SECURITY PANEL TO WORK.
57 - LifeBook Security/Tablet PC ButtonsSetting Supervisor Password You must have set a supervisor password before setting any user passwords. The supervisor password can bypass the user password.1Go to the Start menu.2Click on Run.3Typ e i n: C:\Program Files\Fujitsu\Security Panel Application\Supervisor\ FJSECS.EXE, then press [Enter]4Follow the on-screen instructions to set the Supervisor password.Setting User Password 1Go to the Start menu.2Click on All Programs.3Click on Security Panel Application -> Security Panel Application.4Follow the on-screen instructions to set the user password.Using Your LifeBook Security PanelThe security lock feature is in effect both when the system resumes from Off, Standby, or Hibernation state. You always need to push the Security Panel buttons to input the user password. Your system will not begin the boot sequence until you enter your supervisor/user password.From Off State 1Turn on your system.2When the Security Indicator flashes, enter the password and press Enter button (e.g., if the password is 22222, first press Button 2 five times, then press the Enter button). The notebook will boot to normal operation.YOU MAY CHANGE OR REMOVE THE SUPERVISOR OR USER PASSWORD BY REPEATING THE STEPS DEFINED ABOVE.
58 - LifeBook Security/Tablet PC ButtonsFrom Standby/Hibernation State 1Press your Suspend/Resume button.2When the Security Indicator flashes, enter the password and press Enter button.The notebook should resume normal operation.Incorrect Password Entry If an invalid supervisor or user password is entered three times in succession, the system will “beep” for about one minute. If a valid password is entered within a minute (while system beeps), the beeping will stop and the notebook will resume normal operation. If no password is entered or an invalid password is entered while the system beeps, the system will return to its previous locked state (standby or off) and the Security Indicator will go off. To reactivate the notebook after a password failure, you must press the Suspend/Resume button, then enter a correct password.PrecautionsOpening and Closing the Cover By default, closing the cover automatically places your system into Standby mode. Windows XP systems:You can change the action the system takes when the cover is closed by opening the Power Options Properties icon in the Control Panel, and selecting the Advanced tab. Make a choice from the drop down menu for When I close the lid of my portable computer and click the [OK] button.) Opening the cover does not automatically place the notebook into normal operation. Instead, you must enter the proper security password after pushing the Suspend/Resume button.REMEMBER THE USER PASSWORD YOU SPECIFIED ON THE SECURITY PANEL APPLICATION. IF YOU FORGET THE PASSWORD YOU WILL NOT BE ABLE TO USE YOUR COMPUTER. THE SUPERVISOR PASSWORD CAN OVERRIDE THE USER PASSWORD.
59 - LifeBook Security/Tablet PC ButtonsWindows Vista systems:To change the default for Windows Vista systems when the cover is closed:1Open the system Control Panel.2If the display is in Category view, click Change battery settings under the Mobile PC category. If it is in Classic view, click Power Options.3Click Choose what closing the lid does in the left pane.4Select the desired action for When I close the lid, then click the [Save changes] button.Low Battery Operations If your notebook has a low battery, pushing the suspend/resume button only turns on the Security Indicator. Your notebook does not unlock, the Security Indicator turns off after one minute. To resume normal operation, first attach a power supply to the notebook. Then you may unlock the notebook.Uninstalling/Re-installing the Security Panel ApplicationYou have two options when uninstalling the security panel application:•Remove passwords and uninstall the security panel application software. This will disable all security features.•Uninstall the security panel application with password still active. This will not allow any changes to the password. Uninstalling the Security Panel Application Software Remove passwords when User wants no password protection whatsoever and doesn’t want to give anybody the utility to set a password on their computer. In this case, if passwords (supervisor, user, or both) are set, the passwords must first be cleared BEFORE removing the application. To clear passwords, follow same procedure in SETTING PASSWORD CODES except this time, select REMOVE, enter current password then click Next. When asked to confirm select Yes.
60 - LifeBook Security/Tablet PC ButtonsRemoving Security Panel Application with Passwords Still Active Using this feature will not allow any changes to the password. Windows XP:User: 1Go to Start -> Control Panel.2Open Add or Remove Programs Properties in the Control Panel. 3Select the Security Panel Application in the list, and click Change/Remove. 4When Confirm File Deletion box appears, click Yes.Supervisor:1Go to Start -> Control Panel.2Open Add or Remove Programs Properties in the Control Panel. 3Select the Security Panel Application for Supervisor in the list, and click Change/Remove. 4When Confirm File Deletion box appears, click Yes. Windows Vista:User:1Go to Start -> Control Panel.2Open Programs and Features in the Control Panel. 3Select Security Panel for User in the list, and click Uninstall/Change. REMOVING THE APPLICATIONS DOES NOT REMOVE THE PASSWORD. IT SIMPLY REMOVES THE ABILITY TO CHANGE/ADD/REMOVE PASSWORDS. TO CHANGE YOUR PASSWORD YOU MUST REINSTALL THE APPLICATION.
61 - LifeBook Security/Tablet PC Buttons4When User Account Control box appears, click Continue.Supervisor:1Go to Start -> Control Panel.2Open Add or Remove Programs Properties in the Control Panel. 3Select the Security Panel for Supervisor in the list, and click Uninstall/Change. 4When User Account Control box appears, click Continue. Reinstalling the Security Panel Application To reinstall supervisor or user security application, you will need your Drivers and Applications CD. The Utilities\Security Panel Application folder contains two separate folders: Supervisor and User. The setup files for supervisor and user security applications are contained in those folders. 1Go to the Utilities\Security Panel Application\ Supervisor folder on the CD and double-click the setup.exe file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.2Go to the Utilities\Security Panel Application\User folder on the CD and double-click the setup.exe file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.Supervisor and user passwords can be set via Windows software using the FJSECS.exe and FJSECU.exe files, respectively. FJSECU.exe for the user password cannot run without first setting a supervisor password. You need to run FJSECS.exe first to set the supervisor password. Follow instructions under Setting Passwords on page 56.If you forget both passwords, please contact Fujitsu Computer Systems Corporation Service and Support at 1-800-8FUJITSU (1-800-838-5487). Fujitsu Computer Systems Corporation charges a service fee for unlocking a password-restricted notebook. When calling please have a valid credit card and provide proof of ownership. You will then be given instructions on where to ship your notebook.
62     Chapter 2    Getting Started with Your LifeBookFigure 15.  Connecting the AC AdapterPower SourcesYour Fujitsu LifeBook notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.DC Power JackAC Adapter
63 - Power SourcesConnecting the Power AdaptersThe AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter 1Plug the DC output cable into the DC power jack of your LifeBook notebook.2Plug the AC adapter into an AC electrical outlet. Connecting the Optional Auto/Airline Adapter 1Plug the DC output cable into the DC power jack on your notebook.2Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key in the On or AccessOR3Plug the Auto/Airline adapter into the DC power jack on an airplane seat.Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power 1Be sure that you have at least one charged battery installed.2Remove the AC adapter or the Auto/Airline adapter.THE LITHIUM ION BATTERY IS NOT CHARGED UPON PURCHASE. INITIALLY, YOU WILL NEED TO CONNECT EITHER THE AC ADAPTER OR THE AUTO/AIRLINE ADAPTER TO USE YOUR NOTEBOOK.
64 - Starting Your LifeBook NotebookStarting Your LifeBook NotebookPower OnPower/Suspend/Resume Button The Power/Suspend/Resume button is used to turn on your LifeBook notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your LifeBook notebook. To turn on your LifeBook notebook from its off state, press the Power/Suspend/Resume button, located above the keyboard to the right. When you are done working you can either leave your notebook in Suspend mode, See “Standby (Sleep) Mode” on page 73. or you can turn it off. See “Powering Off” on page 76.. When you power on your LifeBook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LifeBook notebook will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 109. Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.After satisfactory completion of the POST, your notebook will load your operating system.WHEN YOU TURN ON YOUR LIFEBOOK NOTEBOOK BE SURE YOU HAVE A POWER SOURCE. THIS MEANS THAT AT LEAST ONE BATTERY IS INSTALLED AND CHARGED, OR THAT THE AC OR AUTO/AIRLINE ADAPTER IS CONNECTED AND HAS POWER.DO NOT CARRY YOUR LIFEBOOK NOTEBOOK AROUND WITH THE POWER ON OR SUBJECT IT TO SHOCKS OR VIBRATION, AS YOU RISK DAMAGING YOUR NOTEBOOK.
65 - Starting Your LifeBook NotebookBoot SequenceThe procedure for starting-up your notebook is termed the Bootup sequence and involves your notebook’s BIOS. When your LifeBook notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook. This information is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your notebook is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.The boot sequence is executed when:•You turn on the power to your LifeBook notebook.•You restart your notebook from the Windows Shut Down dialog box.•The software initiates a system restart. Example: When you install a new application.Hard Disk Drive PasswordsTo provide additional security for your data, you can assign passwords to your hard disk drive(s). This feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about accessing the utility.NEVER TURN OFF YOUR LIFEBOOK NOTEBOOK DURING THE POWER ON SELF TEST (POST) OR IT WILL CAUSE AN ERROR MESSAGE TO BE DISPLAYED WHEN YOU TURN YOUR LIFEBOOK NOTEBOOK ON THE NEXT TIME. See “Power On Self Test Messages” on page 109.
66 - Starting Your LifeBook NotebookBIOS Setup UtilityThe BIOS Setup Utility is a program that sets up the operating environment for your LifeBook notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your notebook.The BIOS Setup Utility configures:•Device control feature parameters, such as changing I/O addresses and boot devices.•System Data Security feature parameters, such as passwords.Entering the BIOS Setup Utility To enter the BIOS Setup Utility do the following (or use the TrustedCore Menu, as detailed in the next section):1Turn on or restart your LifeBook notebook.2To enter the BIOS Setup Utility, press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.3Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings.Using the TrustedCore Menu When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear. REMEMBER YOUR PASSWORDS. IF YOU SET AND FORGET YOUR USER AND MASTER HARD DISK PASSWORDS, FUJITSU COMPUTER SYSTEMS WILL NOT BE ABLE TO RESET IT. YOU MAY LOSE DATA AND HAVE TO REPLACE YOUR SYSTEM BOARD OR HARD DISK DRIVE.
67 - Starting Your LifeBook NotebookThe TrustedCore Menu provides shortcuts to the following menus and information screens: •BIOS Setup•Diagnostic Screen•Boot Menu•Patent Information•System Information•Continue BootingClicking on any of the fields will invoke the screen, information, or action described.The Boot Menu can also be invoked by pressing the [F12] key when the Fujitsu logo appears on the screen.BIOS Guide A guide to your notebook’s BIOS is available online. Please visit our service and support website at http://www.computers.us.fujitsu.com/support, then select User’s Guides under Online Support. Select your Product, Series, and Model, then click [Go]. Under the Manuals tab, select the BIOS Guide. Booting the SystemWe strongly recommend that you not attach any external devices until you have gone through the initial power on sequence.When you turn on your notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.Depending upon your operating system (Windows Vista or XP edition), there is a different procedure for stating your system for the first time, as outlined below.
68 - Starting Your LifeBook NotebookStarting Windows Vista the first timeIn order to ensure that you receive the most benefits from the Windows Vista operating system, it should be registered the first time you use it. 1First of all, you will need to read and accept the End User License Agreements (EULAs). 2You will be prompted to enter your User Name and Password and you will be given a chance to select an icon for your account.3The next screen asks for a Computer Name and allows you to choose a desktop background. 4You will next see a "Help protect Windows automatically" screen in which the default choice is "Use recommended settings”. The other two choices are "Install important updates only" and "Ask me later". Select from the three choices.5On the next screen set your time and date settings. 6You will next see the "Select your computer's current location" screen. Make your selection from Home, Work (Default), and Public location. 7The "Thank you" screen follows and an offer for free Norton Internet Security is extended. Following are several screens while Windows checks the system performance. THE FIRST TIME YOU INITIALIZE YOUR WINDOWS VISTA SYSTEM, THE SCREEN WILL BE BLANK FOR APPROXIMATELY TWO MINUTES. THIS IS NORMAL. AFTER INITIALIZATION, A “SET UP WINDOWS” DIALOG BOX WILL APPEAR.IMPORTANT: DURING THE SETUP PROCEDURE, DO NOT DISCONNECT THE POWER SUPPLY, PRESS ANY BUTTONS, OR USE ANY PERIPHERAL DEVICES SUCH AS A MOUSE, KEYBOARD, OR REMOTE CONTROL.•IF YOU REJECT THE TERMS OF THE LICENSE AGREEMENTS YOU WILL BE ASKED TO REVIEW THE LICENSE AGREEMENTS FOR INFORMATION ON RETURNING WINDOWS OR TO SHUT DOWN YOUR LIFEBOOK NOTEBOOK.•YOU CANNOT USE YOUR NOTEBOOK UNTIL YOU HAVE ACCEPTED THE LICENSE AGREEMENTS. IF YOU STOP THE PROCESS YOUR NOTEBOOK WILL RETURN TO THE BEGINNING OF THE WINDOWS WELCOME PROCESS, EVEN IF YOU SHUT YOUR NOTEBOOK DOWN AND START IT UP AGAIN.
69 - Starting Your LifeBook Notebook8Windows will then boot up for the first time. As noted above, the first time you initialize your Windows Vista system, the screen will be blank for approximately two minutes. This is normal. During this period, do not disconnect the power supply, press any buttons, or use any peripheral devices such as mouse, keyboard, or remote control.Registering Windows Vista with Microsoft 1After Windows has booted up for the first time, the Control Panel Welcome Center will appear. If the Register Windows Online icon is not seen in the window, click on “Show all xx items” (where “xx” is the number of topics in the Welcome Center).2Click on Register Windows Online and follow the instructions that appear to register your copy of Windows.Starting Windows XP the First TimeRegistering Windows XP with Microsoft In order to ensure that you receive the most benefits from the Windows operating system, it should be registered the first time you use it. After you receive the Windows Welcome screen, you will be prompted to enter registration information in the following order.First of all, you will need to read and accept the End User License Agreements (EULAs). After accepting the EULAs, you will be asked if you want to enable the Automatic Updates feature. Acceptance of this feature is recommended because it allows your system to be updated automatically whenever an important change becomes available for your notebook.•IF YOU REJECT THE TERMS OF THE LICENSE AGREEMENT YOU WILL BE ASKED TO REVIEW THE LICENSE AGREEMENT FOR INFORMATION ON RETURNING WINDOWS OR TO SHUT DOWN YOUR LIFEBOOK NOTEBOOK.•YOU CANNOT USE YOUR LIFEBOOK NOTEBOOK UNTIL YOU HAVE ACCEPTED THE LICENSE AGREEMENT. IF YOU STOP THE PROCESS YOUR NOTEBOOK WILL RETURN TO THE BEGINNING OF THE WINDOWS WELCOME PROCESS, EVEN IF YOU SHUT YOUR NOTEBOOK DOWN AND START IT UP AGAIN.
70 - Starting Your LifeBook NotebookSeveral additional windows will appear, prompting you to enter a name and description for your computer, an Administrator password, and a domain name. Read the instructions on the screens carefully and fill in the information as directed. You will then be automatically connected to the Internet, if you have an appropriate connection available. If an automatic connection is not possible, you will be asked about how you dial out from where you will be using your LifeBook notebook. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button.Once you are connected to the Internet, you will be asked if you wish to continue with the registration. If you select Yes you will then enter your name and address, and email address if desired. Click Next to complete registration.Registering Your LifeBook notebook with FujitsuYou can register your LifeBook by going to our website at: us.fujitsu.com/computersYou will need to be set up with an Internet Service Provider (ISP) to register online.  Installing ClickMe! Windows Vista Systems The first time you boot up your system, you will see a “Primary Settings for the PC” window. This window explains the installations which will be performed by the Click Me! utility. If you click [Execute], ClickMe! will begin installing. If after clicking the button you receive a “User Account BEFORE INSTALLING THE CLICKME! UTILITY, BE SURE THE WIRELESS LAN SWITCH IS TURNED ON.ClickMe!
71 - Starting Your LifeBook NotebookControl” window, you will be asked for your permission to continue. Click [Continue] to continue. If you cancel the operation, the ClickMe! icon will appear on your desktop for later installation. Windows XP Systems The first time you boot up your system, you will see an icon called Click Me! in the Start menu. We highly recommend that you install the ClickMe! utility the first time you boot up. When you click the Click Me! icon, your system will automatically create the related icons in the system tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access, such as wireless LAN software provided by the wireless LAN manufacturer. Fujitsu Driver Update Utility Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 83.THERE MAY BE SOME THIRD-PARTY APPLICATIONS THAT DO NOT GET INSTALLED USING THE CLICKME! UTILITY. FOR MORE INFORMATION, REFER TO YOUR GETTING STARTED GUIDE.
72 - Power ManagementPower ManagementYour Fujitsu LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly. For example, you can create an appropriate power saving profile, put your notebook into Standby (Sleep) mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings.Power/Suspend/Resume ButtonWhen your notebook is active, the Power/Suspend/Resume button can be used to manually put the notebook into Standby mode. Push the Power/Suspend/Resume button when the notebook is active, but not actively accessing anything, and immediately release the button.If your notebook is suspended, pushing the Power/Suspend/Resume button returns your notebook to active operation. You can tell whether the system is Suspended by looking at the Power indicator. If the indicator is visible and not flashing, your notebook is fully operational. If the indicator is visible and flashing, your notebook is in Standby mode. If the indicator is not visible, the power is off or your notebook is in Hibernation mode. (See Hibernation Feature)PLEASE NOTE THAT “STANDBY MODE” IN WINDOWS XP IS KNOWN AS “SLEEP MODE” IN WINDOWS VISTA. THE TWO TERMS ARE INTERCHANGEABLE. FOR PURPOSES OF THIS DOCUMENT, “STANDBY MODE” WILL BE USED.
73 - Power ManagementStandby (Sleep) ModeStandby (Sleep) mode in Windows saves the contents of your system memory during periods of inactivity by maintaining power to critical parts. This mode turns off the CPU, display, hard drive, and all other internal components except those necessary to maintain system memory and for restarting. Your notebook can be put in Standby mode by:•Pressing the Power/Suspend/Resume button when your system is turned on.•Selecting Standby (“Sleep” in Windows Vista) from the Windows Shut Down menu.•Timing out from lack of activity.•Allowing the battery to reach the Dead Battery Warning condition.Your notebook’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Standby mode, your notebook will return to the point where it left off. You must use the Power/Suspend/Resume button to resume operation, and there must be an adequate power source available, or your notebook will not resume.
74 - Power ManagementHibernation (Save-to-Disk) FeatureThe Hibernation feature saves the contents of your notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation Feature Windows Vista: The default settings are not enabled. To enable or disable the Hibernation feature follow these steps:1From the Start menu, select Control Panel, then select the Power Options icon.2Select “Choose what the power button does” or “Choose what closing the lid does”, then make your selections (Do Nothing, Sleep, Hibernate, or Shut Down).■IF RUNNING YOUR NOTEBOOK ON BATTERY POWER, BE AWARE THAT THE BATTERY CONTINUES TO DISCHARGE WHILE YOUR NOTEBOOK IS IN STANDBY MODE, THOUGH NOT AS FAST AS WHEN FULLY OPERATIONAL. ■DISABLING THE POWER/SUSPEND/RESUME BUTTON PREVENTS IT FROM BEING USED TO PUT THE NOTEBOOK INTO STANDBY OR HIBERNATION (SAVE-TO-DISK) MODE. THE BUTTON RESUME FUNCTION CAN’T BE DISABLED.■THE STANDBY OR HIBERNATION (SAVE-TO-DISK) MODE SHOULD NOT BE USED WITH CERTAIN PC CARDS. CHECK YOUR PC CARD DOCUMENTATION FOR MORE INFORMATION. WHEN PC CARDS OR EXTERNAL DEVICES ARE IN USE, HIBERNATION (SAVE-TO-DISK) MODE CANNOT RETURN TO THE EXACT STATE PRIOR TO SUSPENSION, BECAUSE ALL OF THE PERIPHERAL DEVICES WILL BE RE-INITIALIZED WHEN THE SYSTEM RESTARTS.■IF YOUR NOTEBOOK IS ACTIVELY ACCESSING INFORMATION WHEN YOU ENTER THE STANDBY OR HIBERNATION (SAVE-TO-DISK) MODE, CHANGES TO OPEN FILES ARE NOT LOST. THE FILES ARE LEFT OPEN AND MEMORY IS KEPT ACTIVE DURING STANDBY MODE OR THE MEMORY IS TRANSFERRED TO THE INTERNAL HARD DRIVE DURING HIBER-NATION MODE.THE MAIN ADVANTAGE OF USING HIBERNATION (SAVE-TO-DISK) IS THAT POWER IS NOT REQUIRED TO MAINTAIN YOUR DATA. THIS IS PARTICULARLY IMPORTANT IF YOU WILL BE LEAVING YOUR NOTEBOOK IN A SUSPENDED STATE FOR A PROLONGED PERIOD OF TIME. THE DRAWBACK OF USING HIBERNATION MODE IS THAT IT LENGTHENS THE POWER DOWN AND POWER UP SEQUENCES AND RESETS PERIPHERAL DEVICES.
75 - Power ManagementWindows XP:The default settings are not enabled. To enable or disable the Hibernation feature follow these steps:1From the Start menu, select Settings, and then select Control Panel.2From the Control Panel select Power Options.3Select the Hibernate tab. Select the box to enable or disable this feature.Windows Power Management The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Options to set the timeout values for turning off the display and hard disks whether you are running the notebook on battery power or one of the adapters. Restarting the SystemIf your system is on and you need to restart it, be sure that you use the following procedure. Windows Vista:1Click the [Start] button, and then move the mouse over the small arrow at the bottom right of the right-hand pane.2Select Restart from the list.Windows XP:1Click the [Start] button, and then click Turn Off Computer.2Select the Restart option. Your notebook will shut down and then reboot.TURNING OFF YOUR LIFEBOOK NOTEBOOK WITHOUT EXITING WINDOWS OR TURNING ON YOUR NOTEBOOK WITHIN 10 SECONDS OF THE NOTEBOOK BEING SHUT OFF MAY CAUSE AN ERROR WHEN YOU START THE NEXT TIME.
76 - Power ManagementPowering OffBefore turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your notebook shuts down without error, use the Windows shut down procedure.Using the correct procedure to shut down from Windows allows your notebook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:Windows Vista:1Click the [Start] button, and then move the mouse over the small arrow at the bottom right of the right-hand pane.2Select Shut Down from the list.Windows XP:1Click the [Start] button, and then click Turn Off Computer.Select the Turn Off option. If you are going to store your notebook for a month or more, see Care and Maintenance Section. BE SURE TO CLOSE ALL FILES, EXIT ALL APPLICATIONS, AND SHUT DOWN YOUR OPERATING SYSTEM PRIOR TO TURNING OFF THE POWER. IF FILES ARE OPEN WHEN YOU TURN THE POWER OFF, YOU WILL LOSE ANY CHANGES THAT HAVE NOT BEEN SAVED, AND MAY CAUSE DISK ERRORS.
77     Chapter 3    User-Installable FeaturesLithium ion BatteryYour LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.The Lithium ion battery operating time may become shorter if it is used under the following conditions:•When used at temperatures that exceed a low of 5°C or a high of 35°C. Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range. •When using a high current device such as a modem, external optical drive, or the hard drive, using the AC adapter will conserve your battery life.DO NOT LEAVE A FAULTY BATTERY IN YOUR NOTEBOOK. IT MAY DAMAGE YOUR AC ADAPTER, OPTIONAL AUTO/AIRLINE ADAPTER, ANOTHER BATTERY OR YOUR NOTEBOOK ITSELF. IT MAY ALSO PREVENT OPERATION OF YOUR NOTEBOOK BY DRAINING ALL AVAILABLE CURRENT INTO THE BAD BATTERY.
78 - Lithium ion BatteryRecharging the BatteriesIf you want to know the condition of the primary Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes.The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LifeBook notebook and connect the AC or Auto/Airline adapter.There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your notebook into Standby mode, or turn it off while the adapter is charging the battery. (See Power Management on page 72 for more information on Standby mode and shutdown procedure)•ACTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS, APPLICATIONS, FEATURES, POWER MANAGEMENT SETTINGS, BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES. OPTICAL DRIVE OR HARD DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE. THE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF YOUR BATTERY IS RUNNING LOW QUICKLY, YOU SHOULD REPLACE IT WITH A NEW ONE.•UNDER FEDERAL, STATE, OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTING THEM IN THE TRASH. PLEASE TAKE CARE OF OUR ENVIRONMENT AND DISPOSE OF BATTERIES PROPERLY. CHECK WITH YOUR LOCAL GOVERNMENT AUTHORITY FOR DETAILS REGARDING RECYCLING OR DISPOSING OF OLD BATTERIES. IF YOU CANNOT FIND THIS INFORMATION ELSEWHERE, CONTACT YOUR SUPPORT REPRESENTATIVE AT 1-800-8FUJITSU (1-800-838-5487)MAKE SURE THAT THE PERCENTAGE CHARGE IS INDICATED BY THE BATTERY CHARGING INDICATOR ON THE STATUS INDICATOR PANEL.
79 - Lithium ion BatteryLow Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your notebook will go into Standby mode. There is no guarantee that your data will be saved once the notebook reaches this point.Dead Battery Suspend mode shows on the Status indicator just like the normal Standby mode. Once your notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Power/Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your notebook while an adapter is charging the battery.USING HEAVY CURRENT DEVICES OR FREQUENT EXTERNAL OPTICAL DRIVE ACCESSES MAY PREVENT CHARGING COMPLETELY.■ONCE THE LOW BATTERY NOTIFICATION MESSAGE APPEARS, YOU NEED TO SAVE ALL YOUR ACTIVE DATA AND PUT YOUR LIFEBOOK NOTEBOOK INTO STANDBY MODE UNTIL YOU CAN PROVIDE A NEW POWER SOURCE. YOU SHOULD PROVIDE A CHARGED BATTERY, AN AC POWER ADAPTER, OR AUTO/AIRLINE ADAPTER AS SOON AS POSSIBLE.■ WHEN YOU ARE IN STANDBY MODE THERE MUST ALWAYS BE AT LEAST ONE POWER SOURCE ACTIVE. IF YOU REMOVE ALL POWER SOURCES WHILE YOUR LIFEBOOK NOTEBOOK IS IN STANDBY MODE, ANY DATA THAT HAS NOT BEEN SAVED TO THE HARD DRIVE WILL BE LOST.
80 - Lithium ion BatteryShorted Batteries The Status Indicator panel indicator associated with the Battery Level indicator displays the operating level available in that battery. If this display shows a flashing red LED, it means the battery is damaged and must be replaced so it does not damage other parts of your LifeBook notebook.Replacing the Battery With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. There are two ways to swap batteries, cold-swapping and hot-swapping:Cold-swapping Batteries To cold-swap batteries in your battery bay follow these easy steps (Figure 16): 1Have a charged battery ready to install.2Shut down your notebook and disconnect the AC adapter. 3While pushing the battery bay release latches towards each other, slide the battery out of the bay.4Insert a new battery into the bay, and press it in firmly so that the latches click into place. 5Plug in the AC adapter and turn the power on. Hot-swapping Batteries To hot-swap batteries in your battery bay follow these easy steps: 1Plug an AC Adapter into the system and connect it to a power outlet.BE SURE TO PLUG IN AN AC ADAPTER PRIOR TO REMOVING THE BATTERY. THERE IS NO BRIDGE BATTERY PRESENT TO SUPPORT THE SYSTEM WHILE THE BATTERY IS BEING REPLACED. IF YOU DO NOT USE AN AC ADAPTER YOU WILL LOSE ANY UNSAVED FILES.
81 - Lithium ion BatteryFigure 16.  Removing a Battery2Follow steps 3 through 6 in “Cold Swapping Batteries”. Battery Bay Release LatchesBattery PackIF THE LITHIUM ION BATTERY CONNECTOR IS NOT FULLY SEATED, YOU MAY NOT BE ABLE TO USE YOUR NOTEBOOK OR CHARGE YOUR BATTERY.
82 - Memory Stick/Secure Digital CardsFigure 17.  Installing a Memory Stick or SD CardMemory Stick/Secure Digital CardsYour LifeBook notebook supports Memory Sticks and Secure Digital (SD) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data. Memory Stick is a flash memory technology that allows you to record, transfer and share digital content, such as digital pictures, movies, music, voice, and computer data and applications.Secure Digital (SD) Cards are very similar to Memory Sticks. Like Memory Sticks, SD Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. SD Cards transfer data quickly, with low battery consumption. Like the memory stick, it uses flash memory architecture.Memory StickSD Card
83 - Memory Stick/Secure Digital CardsInstalling Memory Stick/SD CardsMemory Stick and SD Cards are installed in the Memory Stick/SD Card slot. To install a Memory Stick or SD Card, follow these steps:1See your specific card manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.2Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD Card.3Insert your card into the slot with the product label facing up.4Push the card firmly into the slot until it is seated in the connector. Removing A Memory Stick/SD CardTo remove a Memory Stick or SD Card, follow these easy steps:1Select Safely Remove Hardware from the System Tray. Highlight the card in the list, then click [Stop].2Push the Memory Stick or SD Card in until it unlatches. It will then eject from the slot for removal.INSTALLING OR REMOVING A MEMORY STICK OR SD CARD DURING YOUR LIFEBOOK NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK NOTEBOOK.DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR LIFEBOOK NOTEBOOK, OR BOTH.SEE YOUR CARD MANUAL FOR SPECIFIC INSTRUCTIONS ON THE REMOVAL OF YOUR CARD. SOME CARDS MAY REQUIRE YOUR LIFEBOOK NOTEBOOK TO BE IN STANDBY MODE OR OFF WHILE REMOVING THEM.
84 - PC CardsFigure 18.  Installing/Removing PC CardPC CardsYour LifeBook notebook supports Type I and Type II PC Cards which can perform a variety of functions depending on which type of card you install. Some available PC Cards:•Gigabit Ethernet Local area network (LAN) cards•IEEE1394 cards•S-ATA II cards•IEEE802.11n WLAN cards•Other PC Cards that conform to PCMCIA 2.1 or CardBus standardsFor further information, refer to the instructions supplied with your card(s).Eject ButtonsPC Card Slot
85 - PC CardsInstalling PC CardsTo install a PC Card in the PC Card slot, follow these steps: 1See your PC Card manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.2Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards.3If the eject button is extended, press it until it clicks. 4Insert the card into the slot with the label facing up.5Push the card firmly into the slot until it is seated in the connector. Removing PC CardsSee your PC Card manual for specific instructions on removing your card. Some cards may require your notebook to be in Standby Mode or Off during removal.•INSTALLING OR REMOVING A PC CARD DURING YOUR LIFEBOOK NOTEBOOK’S SHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK NOTEBOOK.•DO NOT INSERT A PC CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD, YOUR LIFEBOOK NOTEBOOK, OR BOTH.YOU MAY BE REQUIRED TO LOG ON AS AN ADMINISTRATOR OR MEMBER OF THE ADMINISTRATOR’S GROUP TO COMPLETE THIS PROCEDURE. IF THE COMPUTER IS CONNECTED TO A NETWORK, NETWORK POLICY SETTINGS MAY ALSO PREVENT YOU FROM COMPLETING THIS PROCEDURE.•WINDOWS HAS A SHUTDOWN PROCEDURE FOR PC CARDS THAT MUST BE FOLLOWED BEFORE REMOVING A CARD. (REVIEW YOUR OPERATING SYSTEM MANUAL FOR THE CORRECT PROCEDURE.) IT IS GOOD PRACTICE TO REMOVE DEVICES USING THE SAFELY REMOVE HARDWARE ICON IN THE SYSTEM TRAY.•IF THE DIALOG BOX STATES THAT THE DEVICE CANNOT BE REMOVED, YOU MUST SAVE ALL OF YOUR OPEN FILES, CLOSE ANY OPEN APPLICATIONS AND SHUT DOWN YOUR NOTEBOOK.
86 - PC Cards1Unlock the card from the slot by pressing the eject button associated with the slot in which the card is located. When pressed, the button will pop out. 2Firmly press the button again until it is flush with the notebook. This will eject the card slightly out of the slot allowing you to remove the card.Smart Card ReaderA dedicated Smart Card Reader is provided on your notebook. Smart Cards are the same size and shape as credit cards, but they contain an integrated microprocessor chip. The chip can hold a variety of information, and provides you with many possible options, such as allowing you to make secure purchases, pay for phone calls, store security information, and provide personal identification and information. In order to use the Smart Card Reader, you must purchase optional Smart Card third-party software.Figure 19.  Smart Card SlotIF THE PC CARD HAS AN EXTERNAL CONNECTOR AND CABLE, DO NOT PULL THE CABLE WHEN REMOVING THE CARD.Smart Card Slot
90 - Device PortsDevice PortsYour Fujitsu LifeBook notebook and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, printers, etc. Internal LAN (RJ-45) JackThe internal LAN (RJ-45) jack is used for a Gigabit (10Base-T/100Base-Tx/1000Base-T) Ethernet LAN connection. You may need to configure your notebook to work with your particular network. (Please refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these easy steps: Port Replicator ConnectorThe port replicator connector is used for the connection of your notebook to an optional port replicator. In order to connect your notebook to this device, follow the instructions that came with your port replicator. 1Align the connector with the port opening.2Push the connector into the port until it is seated.3Plug the other end of the cable into a LAN outlet.Figure 22.  Connecting the LAN
91 - Device PortsUniversal Serial Bus PortsThe Universal Serial Bus 2.0 ports (USB) allow you to connect USB devices such as external game pads, pointing devices, keyboards and/or speakers. There are four USB 2.0 ports on your notebook: two on the left side and two on the rear.. In order to connect a USB device follow these steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.Figure 23.  Connecting a USB DeviceDUE TO THE ONGOING CHANGES IN USB TECHNOLOGY AND STANDARDS, NOT ALL USB DEVICES AND/OR DRIVERS ARE GUARANTEED TO WORK.
92 - Device PortsIEEE 1394 PortThe 4-pin 1394 port allows you to connect digital devices that are compliant with IEEE 1394 standard. The IEEE 1394 standard is easy to use, connect, and disconnect. This port can allow up to 400 Mbps transfer rate. A third-party application may be required to operate your device with the 1394 port.THE 1394 PORT USED IN THIS SYSTEM USES A FOUR-PIN CONFIGURATION. IF YOU INTEND TO INTERFACE WITH DEVICES WHICH USE A SIX-PIN CONFIGURATION, YOU WILL NEED TO PURCHASE AN ADAPTER. In order to connect a 1394 device, follow these steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.Figure 24.  Connecting an IEEE1394 Device
93 - Device PortsHeadphone JackThe headphone jack allows you to connect headphones or powered external speakers to your notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.Microphone JackThe microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your notebook. In order to connect a microphone follow these easy steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.External Video PortThe external video port allows you to connect an external monitor or LCD projector. In order to connect an external video device, follow these easy steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.3Tighten the two hold-down screws, located on each end of the connector. PRESSING THE [FN] + [F10] KEYS ALLOWS YOU TO CHANGE YOUR SELECTION OF WHERE TO SEND YOUR DISPLAY VIDEO. EACH TIME YOU PRESS THE KEY COMBINATION, YOU WILL STEP TO THE NEXT CHOICE, STARTING WITH THE BUILT-IN DISPLAY PANEL ONLY, MOVING TO THE EXTERNAL MONITOR ONLY, FINALLY MOVING TO BOTH THE BUILT-IN DISPLAY PANEL AND AN EXTERNAL MONITOR.
94 - Device PortsFigure 25.  Connecting an External Video Device
87 - Memory Upgrade ModuleMemory Upgrade ModuleYour Fujitsu LifeBook notebook comes with a minimum of 512 MB of high speed Double Data Rate Synchronous Dynamic RAM (DDR2-533 SDRAM) factory installed. To increase your notebook’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at www.shopfujitsu.com.Installing Memory Upgrade Modules1Turn off power to your notebook, remove any power adapter (AC or auto/airline). Remove the battery. 2Make sure that all the connector covers are closed.3Turn the notebook bottom side up, and remove the screws from the memory upgrade module compartment. 4Slide the cover towards the battery compartment slightly, then lift it and remove it (Figure 20).5Remove the memory upgrade module from the static guarded sleeve.6Align the memory upgrade module with the part side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment.(Figure 21)•DO NOT REMOVE ANY SCREWS FROM THE MEMORY UPGRADE MODULE COMPARTMENT EXCEPT THE ONES SPECIFICALLY SHOWN IN THE DIRECTIONS FOR INSTALLING AND REMOVING THE MEMORY UPGRADE MODULE.•THE MEMORY UPGRADE MODULE CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD). TO MINIMIZE RISK TO THE MODULE, OBSERVE THE FOLLOWING PRECAUTIONS:•BEFORE HANDLING A MEMORY MODULE, TOUCH A GROUNDED METAL OBJECT TO DISCHARGE STATIC ELECTRICITY BUILT UP IN YOUR BODY. •WHEN INSTALLING OR REMOVING A MEMORY MODULE, HOLD IT BY THE EDGE SO AS NOT TO TOUCH ANY CONTACTS OR CHIPS. BE CAREFUL NOT TO TOUCH ANY INTERNAL COMPUTER TERMINALS OR COMPONENTS; THE OIL FROM YOUR FINGERS COULD CAUSE A SHORT TO THE COMPONENTS. •BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING MEMORY MODULES. EVEN IF THE SYSTEM IS IN HIBERNATE OR STANDBY STATES, DATA COULD BE LOST OR THE MEMORY COULD BE DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.
88 - Memory Upgrade Module7Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You’ll hear a click when it is properly in place. 8Replace the cover and reinstall the screws.Figure 20.  Opening Memory Compartment Figure 21.  Installing a Second Memory ModuleTHE MEMORY UPGRADE MODULE IS NOT SOMETHING YOU ROUTINELY REMOVE FROM YOUR NOTEBOOK. ONCE IT IS INSTALLED, YOU CAN LEAVE IT IN PLACE UNLESS YOU WANT TO CHANGE SYSTEM MEMORY CAPACITY.
89 - Memory Upgrade ModuleRemoving a Memory Upgrade Module1Perform steps 1 through 4 of Installing a Memory Upgrade Module.2Pull the clips sideways away from each side of the memory upgrade module at the same time. 3While holding the clips out, remove the module by lifting it up and pulling it away from your notebook. 4Store the memory upgrade module in a static guarded sleeve.5Replace the cover and reinstall the screws.Checking the Memory CapacityOnce you have changed the system memory capacity by replacing the installed module with a larger one, be sure to check that your notebook has recognized the change.Windows XP: Check the memory capacity by clicking [Start] -> Control Panel, then double-clicking the System icon. Select the General tab and check the amount of memory under “Computer:”Windows Vista: •If you are in Control Panel Home view, check the memory capacity by clicking [Start] -> Control Panel -> System and Maintenance -> System -> View amount of RAM and processor speed. The amount of memory is displayed next to “Memory - RAM:” •If you are in Classic view, check the memory capacity by clicking [Start] -> Control Panel -> System. The amount of memory is displayed next to “Memory - RAM:”There may be a variation between the actual memory size and what is displayed. This is possible if your system is configured with an integrated Intel Graphics Media Accelerator which dynamically allocates system memory to accelerate graphics performance.IF THE TOTAL MEMORY DISPLAYED IS INCORRECT, CHECK THAT YOUR MEMORY UPGRADE MODULE IS PROPERLY INSTALLED. (IF THE MODULE IS PROPERLY INSTALLED AND THE CAPACITY IS STILL NOT CORRECTLY RECOGNIZED, SEE TROUBLESHOOTING ON PAGE 95.
95     Chapter 4    Troubleshooting Your LifeBookTroubleshootingThere may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.Identifying the ProblemIf you encounter a problem, go through the following procedure before pursuing complex troubleshooting:1Turn off your LifeBook notebook.2Make sure the AC adapter is plugged into your notebook and to an active AC power source.3Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.4Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.5Turn on your notebook. Make sure it has been off at least 10 seconds before you turn it back on.6Go through the boot sequence.
96 - Troubleshooting Your LifeBook7If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information. 8If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487)  E-mail: 8fujitsu@us.fujitsu.com  Web site: http://www.computers.us.fujitsu.com/support.Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:•Product name•Product configuration number•Product serial number•Purchase date•Conditions under which the problem occurred•Any error messages that have occurred•Type of device connected, if anySee the Configuration Label on the bottom of your notebook for configuration and serial numbers. IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE.
97 - Troubleshooting Your LifeBookSpecific ProblemsUsing the Troubleshooting Table When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.Troubleshooting TableProblemPageAudio Problems. . . . . . . . . . . . . . . . . .  page 98Optical Drive Problems . . . . . . . . . . . .  page 98Port Replicator Problems  . . . . . . . . . .  page 99Floppy Disk Drive Problems . . . . . . .  page 100Hard Drive Problems. . . . . . . . . . . . .  page 100Keyboard or Mouse Problems. . . . . .  page 100Memory Problems. . . . . . . . . . . . . . .  page 101ProblemPageModem Problems page 101USB Device Problems . . . . . . . . . . . . .page 101PC Card Problems . . . . . . . . . . . . . . . .page 102Power Failures . . . . . . . . . . . . . . . . . . .page 102Shutdown and Startup Problems . . . . .page 105Video Problems  . . . . . . . . . . . . .  page 106Miscellaneous Problems. . . . . . .  page 108
98 - Troubleshooting Your LifeBookProblem Possible Cause Possible SolutionsAudio ProblemsThere is no sound coming from the built-in speaker.The volume is turned too low. Adjust the volume control on your notebook and operating system. Use the [Fn+F9] key combination on your keyboard. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your notebook.The software volume control is set too low.Manually adjusting the volume (i.e., keyboard "hot keys") should dynamically adjust the volume of the operating sys-tem (see above). If that doesn’t work, adjust the sound vol-ume control settings in your software or application.Headphones are plugged into your notebook.Plugging in headphones disables the built-in speakers. Remove the headphones.BIOS audio settings are incor-rect.Set the BIOS setup utility to the default values within the Mul-timedia Device Configuration menu. See “BIOS Setup Utility” on page 66.Software driver is not  configured correctly.The audio driver may be installed or reinstalled using the Drivers and Applications CD that came with your Fujitsu Life-Book. Refer to your application and operating system docu-mentation for help.The speakers have been muted using the Volume icon in the system tray.Click on the Volume icon in the system tray on the bottom right of the screen. (It looks like a speaker). If the Mute box is checked (Windows XP) or the Mute icon has a red circle on it (Windows Vista), click on it to unselect it. You can also use the [Fn+F3] key combination to toggle the volume on and off. Pressing [F3] while holding [Fn] will toggle the audio mute.Optical Drive Problems (optional external device)LifeBook notebook fails to recognize DVD/CD-RW/CD-ROM’s.The disc is not pushed down onto raised center circle of the drive.Open optical drive tray and re-install the disc properly.
99 - Troubleshooting Your LifeBookLifeBook notebook fails to recognize DVD/CD-RW/CD-ROM’s.(continued)Optical drive tray is not latched shut.Push on the front of the optical drive tray until it latches. If that doesn’t work, pull out the modular drive latch to remove the device from the bay, then re-insert the drive until it latched; this ensures that the drive is properly seated. Incorrect DVD Player or no DVD Player software is installed.Install DVD Player software. (See “Media Player Software” on page 73 for more information.)Wrong drive designator was used for the disc in the appli-cation.Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a DVD/CD, drive designa-tions are automatically adjusted. Note that the drive designa-tion can be changed with the Disk Management tool located at Administrative Tools -> Computer Management.DVD/CD-RW/CD-ROM is dirty or defective.Wipe the disc with a non-abrasive CD cleaning cloth and reinsert. It if still will not work try another DVD/CD-RW/CD-ROM in the drive.The drive access indicator on the Status Indicator Panel blinks at regular intervals with no disc in the tray or the drive is not installed.The Windows auto insertion function is active and is checking to see if a disc is ready to run. This is normal. However, you may disable this feature. Port Replicator ProblemsNote: Be sure to power down your LifeBook notebook before adding a printer to the Port Replicator parallel port.Notebook does not turn on when installed in the optional Port ReplicatorPort Replicator AC adapter is not plugged in.Provide power to the Port Replicator.Notebook is not properly seated in the Port Replicator.Remove and re-dock your LifeBook notebook.Problem Possible Cause Possible Solutions
100 - Troubleshooting Your LifeBookFloppy Disk Drive ProblemsYou cannot access your optional external floppy disk.You tried to write to a write protected floppy disk.Eject the disk and set it to write enable. Disk is not loaded correctly. Eject floppy disk, check orientation and re-insert. The floppy disk drive may not be properly installed.Remove and re-install your floppy disk drive. Security is set to protect access to floppy disk data.Verify your password and security settings.Hard Drive ProblemsYou cannot access your hard drive.The wrong drive designator was used by an application when a bootable disc was used to start the notebook.Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted. Security is set so your operat-ing system cannot be started without a password.Verify your password and security settings.Keyboard or Mouse ProblemsThe built-in keyboard does not seem to work.The notebook has gone into Standby mode.Push the Power/Suspend/Resume button.Your application has locked out your keyboard.Try to use your integrated pointing device to restart your sys-tem. You have installed an  external keyboard or mouse, and it does not seem to work.Your external device is not properly installed.Re-install your device. See “Device Ports” on page 90.Your operating system is not set up with correct software driver for that device.Check your device and operating system documentation and activate the proper driver.Problem Possible Cause Possible Solutions
101 - Troubleshooting Your LifeBookYou have connected an external keyboard or a mouse and it seems to be locking up the system.Your operating system is not setup with correct software driver for that device.Check your device and operating system documentation and activate the proper driver.Your system has crashed. Try to restart your notebook. IMemory ProblemsYour System screen in the Control Panel does not show the correct amount of installed memory.Your memory upgrade mod-ule is not properly installed.Remove and re-install your memory upgrade module. See “Memory Upgrade Module” on page 87.You have a memory failure.Check for Power On Self Test (POST) messages. See “Power On Self Test Messages” on page 109.Modem Problems (optional device)Messages about modem operation.Messages about modem operation are generated by whichever modem applica-tion is in use.See your application software documentation for additional information. USB Device ProblemsYou have installed a USB device. Your LifeBook notebook does not recog-nize the device, or the device does not seem to work properly.The device is not properly installed.Remove and re-install the device. See “Device Ports” on page 90.The device may have been installed while an application was running, so your note-book is not aware of its instal-lation.Close the application and restart your notebook.Your device may not have the correct software driver active.See your software documentation and activate the correct driver.Problem Possible Cause Possible Solutions
102 - Troubleshooting Your LifeBookYou have installed a USB device. Your LifeBook notebook does not recog-nize the device, or the device does not seem to work properly.(continued)You may have the wrong I/O address selected for your device.See your device and software documentation to determine the required I/O address. Change the settings in the BIOS setup utility. See “BIOS Setup Utility” on page 66.Your device and another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.Parallel port is set to output only.Check parallel port setting in the BIOS and set to bi-direc-tional or ECP.PC Card ProblemsA card inserted in the PC Card slot does not work or is locking up the system.Card is not properly installed. Remove and re-install the card. See “PC Cards” on page 84.Card may have been installed while an application was run-ning, so your notebook is not aware of its installation.Close the application and restart your notebook.Your software may not have the correct driver active.See your software documentation and activate the correct driver.You may have the wrong I/O address selected for your card device.See your PC Card documentation to determine the required I/O address. Change the settings in the BIOS. See “BIOS Setup Utility” on page 66.Your card device and another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.Power FailuresYou turn on your LifeBook notebook and nothing seems to happen.The installed battery is com-pletely discharged or there is no Power adapter (AC or Auto/Airline) installed.Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 30. Install a charged battery or a Power adapter.Problem Possible Cause Possible Solutions
103 - Troubleshooting Your LifeBookYou turn on your LifeBook notebook and nothing seems to happen. (continued)The battery is installed but is faulty.Use the Status Indicator panel to verify the presence and condition of the battery. See “Status Indicator Panel” on page 30. If the battery indicates a short, remove it and  operate from another power source or replace that battery.The battery is low. Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 30. Use a Power adapter to operate until a battery is charged or install a charged battery.The power adapter (AC or auto/airline) is not plugged in properly.Verify that your adapter is connected correctly. See “Power Sources” on page 62.The power adapter (AC or auto/airline) has no power from the AC outlet, airplane jack, or car cigarette lighter.Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.The power adapter (AC or auto/airline) is faulty.Try a different power adapter.Your LifeBook notebook turns off all by itself.The power management parameters are set for auto timeouts which are too short for your operating needs.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Sus-pend/Resume button. Check your power management set-tings, or close your applications and go to the Power Options located in the Control Panel to adjust the timeout values to better suit your needs.You are operating on battery power and ignored a low bat-tery alarm until the battery was at the dead battery state and the system has entered Dead Battery Suspend mode.Install a power adapter, then push the Power/Sus-pend/Resume button. See “Power Sources” on page 62.Problem Possible Cause Possible Solutions
104 - Troubleshooting Your LifeBookYour LifeBook notebook turns off all by itself.(continued)You have a battery failure. Verify the condition of the battery using the Status Indicator panel. If the battery is shorted, replace or remove it. See “Status Indicator Panel” on page 30.Your power adapter has failed or lost its power source.Make sure the adapter is plugged in and the outlet has power.Your LifeBook notebook will not work on battery alone.The installed battery is dead. Replace the battery with a charged one or install a power adapter.No battery is installed. Install a charged battery.The battery is improperly installed.Verify that the battery is properly connected by re-installing it.Your installed battery is faulty. Verify the condition of the battery using the Status Indicator panel and replace or remove any batteries that are shorted. See “Status Indicator Panel” on page 30.The battery seems to  discharge too quickly.You are running an applica-tion that uses a lot of power due to frequent hard drive access or optical drive access, or use of a modem, LAN PC card, Wireless LAN, or Bluetooth device.Use a power adapter for this application when at all possible.The power savings features may be disabled.Check the Power Options menu settings and adjust accord-ing to your operating needs.The brightness is turned all the way up.Turn down the brightness adjustment. The higher the bright-ness the more power your display uses.The battery is very old. Replace the battery.Problem Possible Cause Possible Solutions
105 - Troubleshooting Your LifeBookThe battery seems to  discharge too quickly (continued)The battery has been exposed to high tempera-tures.Replace the battery.The battery is too hot or too cold. Restore the notebook to normal operating temperature. Charging icon on the Status Indicator panel will flash when battery is outside of operating range.Shutdown and Startup ProblemsThe Suspend/Resume  button does not work.Suspend/Resume  button is disabled. In Windows XP, enable the button by going to the Control Panel -> Power Options Properties and clicking on the Advanced tab. In the Power buttons area, select the option that best suits your needs. In Windows Vista, select the Change what the power button does” option.There may be application software. conflictClose all applications and try the button again.The system powers up, and displays power on information, but fails to load the operating system.The boot sequence settings of the setup utility are not compatible with your configu-ration.Set the operating source by pressing the [ESC] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. See “BIOS Setup Utility” on page 66.You have a secured system requiring a password to load your operating system.Make sure you have the right password. Enter the setup util-ity and verify the Security settings and modify them as accordingly. See “BIOS Setup Utility” on page 66.Internal hard drive was  not detected.Use the BIOS setup utility or Primary Master submenu, located within the Main menu, to try to auto detect the inter-nal hard drive.An error message is dis-played on the screen dur-ing the notebook (boot) sequence.Power On Self Test (POST) has detected a problem.See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. See “Power On Self Test Messages” on page 109.Problem Possible Cause Possible Solutions
106 - Troubleshooting Your LifeBookYour notebook appears to change setup parameters when you start it.BIOS setup changes were not saved when made and you exited the setup utility.Make sure you select Save Changes And Exit when exiting the BIOS setup utility.The BIOS CMOS hold-up bat-tery has failed.Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years.Your system display won’t turn on when the system is turned on or has resumed.You have installed the Life-Book/Security Application panel.Check the Status Indicator Panel for presence of the Security icon. If it is visible, enter your password See “Status Indicator Panel” on page 30.Video ProblemsThe built-in display is blank when you turn on your LifeBook notebook.The notebook is set for an external monitor only.Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the keys you will step to the next choice. The choices, in order are: built-in display only, external moni-tor only, both built-in display and external monitor.Display angle and brightness settings are not adequate for your lighting conditions.Move the display and the brightness control until you have adequate visibility. Pressing either the [F6] or [F7] keys while holding down the [Fn] key also allows you to change the brightness level of the display.Power management timeouts are set for short intervals and you didn’t see the display go on and off again.Press a keyboard button or move the mouse to restore oper-ation. If that fails, push the Power/Suspend/Resume button. (The display may be shut off by Standby mode, Auto Sus-pend or Video Timeout)The notebook turned on with a series of beeps and the built-in display is blank.Power On Self Test (POST) has detected a failure which does not allow the display to operate. Contact your support representative.Problem Possible Cause Possible Solutions
107 - Troubleshooting Your LifeBookThe display goes blank by itself after you have been using it.The notebook has gone into Video timeout, Standby mode, or Save-to-Disk mode because you have not used it for a period of time.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Sus-pend/Resume button. Check your power management set-tings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. See “BIOS Setup Utility” on page 66.The power management time-outs may be set for very short intervals and you failed to notice the display come on and go off again.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Sus-pend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout)Your display won’t turn on when the system is turned on or when it has resumed.The system may be pass-word-protected.Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.The display does not close.A foreign object, such as a paper clip, is stuck between the display and keyboard.Remove all foreign objects from the keyboard.The display has bright or dark spots.If the spots are very tiny and few in number, this is normal for a large LCD display.This is normal; do nothing.If the spots are numerous or large enough to interfere with your operation needs.Display is faulty; contact your support representative.The application display uses only a portion of your screen and is surrounded by a dark frame.You are running an applica-tion that does not support 800 x 600/1024 x 768 pixel resolu-tion display and display com-pression is enabled.Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing display compression settings, (See Video Features submenu located within the Advanced menu of the BIOS. See “BIOS Setup Utility” on page 66.Problem Possible Cause Possible Solutions
108 - Troubleshooting Your LifeBookThe Display is dark when on battery power.The Power Management util-ity default is set on low bright-ness to conserve power.Press [Fn] + [F7] to increase brightness or double-click on the battery gauge and adjust Power Control under battery settings.You have connected an external monitor and it does not display any infor-mation.Your BIOS setup is not set to enable your external monitor.Toggle the video destination by pressing [Fn]+ [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. See “BIOS Setup Utility” on page 66.Your external monitor is not properly installed. Reinstall your device. See “External Video Port” on page 93.Your operating system is not setup with the correct soft-ware driver for that device. Check your device and operating system documentation and activate the proper driver.You have connected an external monitor and it does not come on.Your external monitor is not compatible with your LifeBook notebook.See your monitor documentation and the External Monitor Support portions of the Specifications section. See “Specifi-cations” on page 129.Miscellaneous ProblemsError message is dis-played on the screen dur-ing the operation of an application.Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.Problem Possible Cause Possible Solutions
109 - Troubleshooting Your LifeBookPower On Self Test MessagesThe following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.nnnn Cache SRAM Passed  Where nnnn is the amount of system cache in kilobytes success-fully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)*Diskette drive A error or Diskette drive B error Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, See “BIOS Setup Utility” on page 66. and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative.*Extended RAM Failed at offset: nnnn  Extended memory not working or not configured properly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is properly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.nnnn Extended RAM Passed  Where nnnn is the amount of memory in kilobytes successfully tested.*Failing Bits: nnnn The hex number nnnn This is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.
110 - Troubleshooting Your LifeBook*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4)  The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.*Incorrect Drive A type – run SETUP Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.*Incorrect Drive B type – run SETUP Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.*Invalid NVRAM media type Problem with NVRAM access. In the unlikely case that you see this message you may have some display problems. You can continue operating but should contact your support representative for more information.*Keyboard controller error  The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.*Keyboard error  Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.
111 - Troubleshooting Your LifeBook*Keyboard error nn BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.*Monitor type does not match CMOS – Run SETUP Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.*Operating system not found  Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted.*Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative.*Parity Check 2 nnnn  Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data-destroying failure. Contact your support representative.
112 - Troubleshooting Your LifeBook*Press <F1> to resume, <F2> to SETUP  Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings.*Previous boot incomplete – Default configuration used  Previous Power On Self Test did not complete successfully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power and contact your support representative.*Real time clock error  Real-time clock fails BIOS test. May require board repair. Contact your support representative.*Shadow RAM Failed at offset: nnnn  Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corruption if you continue. Contact your support representative.nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested.*System battery is dead – Replace and run SETUP  The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your notebook. This battery has an expected life of 2 to 3 years.System BIOS shadowed System BIOS copied to shadow RAM.
113 - Troubleshooting Your LifeBook*System CMOS checksum bad – run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.*System RAM Failed at offset: nnnn  System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.nnnn System RAM Passed Where nnnn is the amount of system memory in kilobytes successfully tested.*System timer error  The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.UMB upper limit segment address: nnnn  Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.Video BIOS shadowed  Video BIOS successfully copied to shadow RAM..
114 - Restoring Your Pre-installed SoftwareRestoring Your Pre-installed SoftwareThe Drivers and Applications Restore (DAR) DVD contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your computer configuration for use as documented below.Re-installing Individual Drivers and ApplicationsThe Drivers and Applications CD can be used to selectively re-install drivers and/or applications that may have been un-installed or corrupted. To re-install drivers and/or applications:1Boot up the system and insert the DAR CD after Windows has started. A Fujitsu Installer screen is displayed after the CD is inserted.2After reading the License Agreement, click [I agree].3A window will appear containing a list of applications, drivers, and utilities that you can install from the Drivers and Applications CD.IN ORDER TO INSTALL APPLICATIONS AND/OR DRIVERS FROM THE DAR DVD, YOU WILL NEED TO USE A DVD DRIVE ATTACHED EXTERNALLY.IF YOU HAVE ACCESS TO THE INTERNET, VISIT THE FUJITSU SUPPORT WEBSITE AT HTTP://WWW.COMPUTERS.US.FUJITSU.COM/SUPPORT TO CHECK FOR THE MOST CURRENT INFORMATION, DRIVERS AND HINTS ON HOW TO PERFORM RECOVERY AND SYSTEM UPDATES.THERE MAY BE CERTAIN FREE THIRD-PARTY APPLICATIONS PRE-INSTALLED ON YOUR SYSTEM THAT ARE NOT ON THE DAR CD. THE LATEST VERSIONS OF THE APPLICATIONS CAN BE DOWNLOADED FROM THE THIRD-PARTY’S WEBSITE.
115 - Restoring Your Pre-installed Software4In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately.5Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed.6After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system. Restoring the Operating System for Windows XP SystemsThe Recovery and Utility disc contains three utilities:•The Recovery utility allows you to restore the system operating system (OS). The restored OS is the same one that was originally installed on the hard disk drive. After the OS is restored, you will need to reinstall the drivers and applications from the Drivers and Applications Restore disc and from any application discs that were bundled with the system when you purchased it. •The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk,  including all partitions.•The Partition Creation utility allows you to create or resize partitions on your hard disk. NOTE: Creating or resizing partitions with this utility will cause all data on the hard disk to be completely erased.THE COMPONENTS LISTED ARE COLOR-CODED IN TERMS OF THEIR INSTALL STATUS. BLUE INDICATES THAT THE COMPONENT CAN BE INSTALLED. GREEN INDICATES THAT THE COMPONENT NEEDS TO BE INSTALLED SEPARATELY. GREY INDICATES A COMPONENT THAT IS ALREADY INSTALLED; GREY ITEMS CAN BE REINSTALLED, BUT PRIOR TO INSTALLATION YOU WILL RECEIVE A REMINDER THAT THE COMPONENT IS ALREADY INSTALLED.
116 - Restoring Your Pre-installed SoftwareBOOT Priority Change Before restoring an image, you must first verify that the system is set up to boot from the DVD drive. To verify/change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps:1Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.2Using the arrow keys, go to the Boot menu.3Arrow down to the Boot Device Priority submenu. Press [Enter].4If “Optical Media Drive” or “CD-ROM Drive” is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.). Note that the BIOS for some systems will indicate “CD-ROM Drive”, even when a DVD drive is connected.5If you have an external DVD drive connected, proceed to the next step; otherwise, proceed to step 7.6If you have an external DVD drive connected:•Select the Advanced menu in the BIOS window.•Scroll down to the USB Features submenu and press the Enter key to open it.•If Legacy USB Support is disabled, press the space bar to enable it.•Scroll down to SCSI SubClass Support and press the space bar to  enable it. 7Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.After you have changed the boot priority, you can restore a backup image when you are booting up.•THE USE OF THIS DISC REQUIRES THAT YOU HAVE A DEVICE CAPABLE OF READING DVDS ATTACHED TO YOUR SYSTEM. YOU WILL NEED TO ATTACH AN EXTERNAL PLAYER. FOR MORE INFORMATION ON AVAILABLE EXTERNAL DEVICES, VISIT OUR WEB SITE AT: US.FUJITSU.COM/COMPUTERS. •THIS DISC CAN ONLY BE USED WITH THE SYSTEM WITH WHICH IT WAS PURCHASED.
117 - Restoring Your Pre-installed SoftwareProcedure 1Turn on the power to your system.2Ensure that you have a device that can read DVDs either installed in your system or attached externally to it.3Insert the Restore Disc into the drive tray.4Reboot your system.After the system reboots, follow the instructions that appear to restore your  operating system, erase all data from your hard disk, or create or resize partitions on the hard disk.Restoring the Operating System for Windows Vista SystemsThe Recovery and Utility disc contains four utilities:•The Recovery utility allows you to restore the system operating system (OS). The restored OS is the same one that was originally installed on the hard disk drive. After the OS is restored, you will need to reinstall the drivers and applications from the Drivers and Applications Restore disc and from any application discs that were bundled with the system when you purchased it.•The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk  and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.•The Partition Creation utility allows you to create a new D: partition or resize existing  partitions on your hard disk. NOTE: Creating or resizing partitions with this utility will cause all data on the hard disk to be completely erased.•The Diagnostics utility allows the IT professional to determine device status/condition by executing diagnostics tests on selected system components.Methods for accessing the utilities Certain LifeBook models have the Recovery and Utility applets pre-installed on a hidden drive. Other systems require that the Recovery and Utility disc be used (or in the event the hard disk has been reformatted).
118 - Restoring Your Pre-installed SoftwareIn order to determine the method for accessing the Recovery and Utility applet, perform the  following procedures in order.Determining whether Recovery and Utility is pre-loaded 1Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. 2From the Boot Menu that appears, check whether the <Recovery and Utility> option is present. If it is not present, it means that the utility must be used from the disc. Proceed to “Running Recovery and Utility from the disc” if <Recovery and Utility> is unavailable.Running Recovery and Utility from hard disk 1Cursor down to <Recovery and Utility> and press the [Enter] key.2While the files are being loaded from the disc, a progress bar will appear at the bottom of the screen.3When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next].4When the Operating System dialog appears, click [Next]. 5If necessary, enter your password, then click [OK].6When System Recovery Options window appears, click on Recovery and Utility.7The Recovery and Utility screen appears on the screen with three tabs: Diagnostics,  Recovery and Utility. Please note that Diagnostics tab is not supported on certain LifeBook/Stylistic models when running Recovery and Utility from the hard disk. In order to restore the operating system, please insert the “Recovery and Utility” disc in the CD/DVD drive and use the Start Recovery function under the Recovery tab. For more information about the tabs, go to “Recovery and Utility tabs” on page 120.Running Recovery and Utility from the disc •THE USE OF THIS DISC REQUIRES THAT YOU HAVE A DEVICE CAPABLE OF READING DVDS ATTACHED TO YOUR SYSTEM. YOU WILL NEED TO ATTACH AN EXTERNAL PLAYER. FOR MORE INFORMATION ON AVAILABLE EXTERNAL DEVICES, VISIT OUR WEB SITE AT: US.FUJITSU.COM/COMPUTERS. •THIS DISC CAN ONLY BE USED WITH THE SYSTEM WITH WHICH IT WAS PURCHASED.
119 - Restoring Your Pre-installed SoftwareBOOT Priority Change Before restoring an image, you must first verify that the system is set up to boot from the DVD drive. To verify/change the boot-up priority (rather than booting-up from the hard drive or  an external floppy disk drive), perform the following steps:1Start your system and press the [F2] key when the Fujitsu logo appears. (Alternately, you  can press the [F12] key when the logo appears, then select <Enter BIOS Setup>.) You will enter the BIOS Setup Utility.2Using the arrow keys, go to the Boot menu.3Arrow down to the Boot Device Priority submenu. Press [Enter].4If “Optical Media Drive”, “CD-ROM Drive”, or “CD/DVD Drive” is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the  top of the list. (The system attempts to boot from the devices in the order in which they are listed.). Note that the BIOS for some systems will indicate “CD-ROM Drive”, even when a DVD drive is connected.5If you have an external DVD drive connected, proceed to the next step; otherwise, proceed to step 7.6If you have an external DVD drive connected:•Select the Advanced menu in the BIOS window.•Scroll down to the USB Features submenu and press the Enter key to open it.•If Legacy USB Support is disabled, press the space bar to enable it.•Scroll down to SCSI SubClass Support and press the space bar to enable it. 7Press [F10], then click [Yes] to exit the BIOS Setup Utility and return to the boot process.After you have changed the boot priority, you can restore a backup image when booting up.Procedure for using Recovery and Utility disc 1Turn on the power to your system.2Ensure that you have a device that can read DVDs either installed in your system or attached externally to it, and that it has been set up as the Boot device (in accordance with “BOOT Priority Change” on page 119).
120 - Restoring Your Pre-installed Software3Insert the Recovery and Utility disc into the drive tray. With the boot priority set in the procedure above, the system will boot from the Recovery and Utility disc.4Reboot your system. After the system reboots, the Recovery and Utility screen appears. On the screen are three tabs: Diagnostics, Recovery, and Utility.Recovery and Utility tabs Diagnostics tab: The Diagnostics tool is designed for use by IT professionals. It is not likely you will need to use this tool. When you select devices from the Diagnosis window then click [Execute], several tests are performed on the selected components.Recovery tab: The Recovery tab contains the Start Recovery tool. Note that the recovery process erases all data from the C: drive. If you decide to use the recovery tool, be sure to back up all data that you don’t want to lose. Also note that you must run the system using your AC adapter while running the recovery tool. To use the Recovery tool, select the Start Recovery function, click on the [Execute] button, then follow the instructions on the screen.Utility tab: The Utility tab contains three tools: System Restore, Hard Disk Data Delete and Partition Creation.•System Restore can help fix problems that might be making your computer run slowly or stop responding. System Restore enables you in rolling back the system to an earlier restore point, and does not affect any of your documents, pictures, or other personal data. •The Hard Disk Data Delete utility is used to delete all data on the hard disk and prevent the data from being reused. NOTE: Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.•The Partition Creation utility allows you to create a D: partition or resize existing partitions on your hard disk. NOTE: Creating or resizing partitions with this utility will cause all data on the hard disk to be completely erased.Automatically Downloading Driver UpdatesYour system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system.
121 - Restoring Your Pre-installed SoftwareThe FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one). If the icon does not appear in the system tray, go to [Start] -> All Programs, and click on Fujitsu Driver Update; this will create the icon automatically.To invoke the FDU menu, you can either right-click on the FDU icon or hold the pen on the icon for a couple of seconds until the menu appears. The menu contains the following items:Check for updates now  Allows for manual driver update search. The first time it is used, you are prompted to agree to a user agreement. After clicking on the icon, the FDU automatically connects with the Fujitsu site to check for updates and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be used while the download is in process. When the update is complete, a message appears informing you of the fact.Enable Automatic Update Notifications Automatically searches for new updates on a regular basis (approximately every 3 days).Show update history  Brings up a screen that displays a history of updates that have been made via the FDU.About Fujitsu Driver Update Displays the FDU version number and copyright informationFujitsu Driver Update Readme Displays the FDU readme.
122     Chapter 5    Care and MaintenanceCaring for your LifeBook NotebookIf you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices.•THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD). TO MINIMIZE RISK TO THE COMPONENTS, OBSERVE THE FOLLOWING PRECAUTIONS:•BEFORE DOCKING OR UNDOCKING YOUR LIFEBOOK NOTEBOOK (WHEN USING A PORT REPLICATOR), IT IS A GOOD PRACTICE TO ALWAYS TOUCH A GROUNDED METAL OBJECT TO DISCHARGE STATIC ELECTRICITY BUILT UP IN YOUR BODY. •BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING SYSTEM COMPONENTS. EVEN IF THE SYSTEM IS IN HIBERNATE OR STANDBY STATES, DATA COULD BE LOST OR MEMORY COULD BE DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.•WHEN INSTALLING OR REMOVING A MEMORY MODULE, HOLD IT BY THE EDGE SO AS NOT TO TOUCH ANY CONTACTS OR CHIPS. BE CAREFUL NOT TO TOUCH ANY INTERNAL COMPUTER TERMINALS OR COMPONENTS; THE OIL FROM YOUR FINGERS COULD CAUSE A SHORT TO THE COMPONENTS. •ELECTRICAL EQUIPMENT MAY BE HAZARDOUS IF MISUSED. OPERATIONS OF THIS PRODUCT OR SIMILAR PRODUCTS, MUST ALWAYS BE SUPERVISED BY AN ADULT. DO NOT ALLOW CHILDREN ACCESS TO THE INTERIOR OF ANY ELECTRICAL PRODUCTS AND DO NOT PERMIT THEM TO HANDLE ANY CABLES.
123 - Care and Maintenance•Your LifeBook notebook is a durable but sensitive electronic device. Treat it with respect and care.•Make a habit of transporting it in a suitable carrying case.•Do not attempt to service the computer yourself. Always follow installation instructions closely.•Keep it away from food and beverages.•To protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used. •Do not operate the notebook in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.•If you accidentally spill liquid on your LifeBook notebook:1Tur n i t o ff.2Position it so that the liquid can run out.3Let it dry out for 24 hours, or longer if needed.4If your notebook will not boot after it has dried out, call your support representative.•Do not use your Fujitsu LifeBook notebook in a wet environment (near a bathtub, swimming pool).•Always use the AC adapter and batteries that are approved for your notebook.•Avoid exposure to sand, dust and other environmental hazards.•Do not expose your notebook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your notebook.•Keep the covers closed on the connectors and slots when they are not in use.•Do not put heavy or sharp objects on the computer.•If you are carrying your LifeBook notebook in a briefcase, or any other carrying case, make sure that there are no objects in the case pressing on the lid.•Never position your notebook such that the optical drive is supporting the weight of the notebook.
124 - Care and MaintenanceCleaning your LifeBook notebook•Always disconnect the power plug. (Pull the plug, not the cord.)•Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.•Use a soft cloth to remove dust from the screen. Never use glass cleaners.Storing your LifeBook notebook•If storing your notebook for a month or longer, turn your LifeBook notebook off, fully charge the  battery(s), then remove and store all Lithium ion batteries.•Store your notebook and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your LifeBook.•Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between 13ºF  (-25ºC) and 140ºF (60ºC).Traveling with your LifeBook notebook•Do not transport your notebook while it is turned on. •Always bring your System Recovery CD that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any problems. •Never put your notebook through a metal detector. Have your notebook hand-inspected by security personnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel. Security officials may require you to turn your notebook On. Make sure you have a charged battery on hand. •When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine. /
125 - Care and Maintenance•Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.•It is recommended that you carry your notebook with you while traveling, rather than checking it in as baggage.BatteriesCaring for your Batteries •Always handle batteries carefully.•Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.Outlet Type LocationUnited States, Canada, parts of Latin America, Mexico, Japan, Korea, the Philippines, TaiwanRussia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South AsiaUnited Kingdom, Ireland, Malaysia, Singapore, parts of AfricaChina, Australia, New Zealand
126 - Care and Maintenance•Do not drop, puncture, disassemble, mutilate or incinerate the battery.•Recharge batteries only as described in this manual and only in ventilated areas.•Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten the life of your battery.•Do not leave a battery in storage for longer than 6 months without recharging it.Increasing Battery Life •Power your LifeBook notebook through the AC or optional auto/airline adapter whenever possible.•If your notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.•Keep brightness to the lowest level comfortable.•Set the power management for maximum battery life.•Put your notebook in Standby mode when it is turned on and you are not actually using it.•Limit your media drive access.•Disable the Media Player auto insert notification function.•Always use fully charged batteries.•Eject PCMCIA cards when not in use.Media CareCaring for your Media (DVD/CD/CD-R) Media discs are precision devices and will function reliably if given reasonable care.•Always store your media disc in its case when it is not in use.•Always handle discs by the edges and avoid touching the surface.•Avoid storing any media discs in extreme temperatures.
127 - Care and Maintenance•Do not bend media discs or set heavy objects on them.•Do not spill liquids on media discs.•Do not scratch media discs.•Do not get dust on media discs.•Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.•If a media disc is subjected to a sudden change in temperature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry media discs.•If a disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.Caring for your Optical Drive Your optional external optical drive is durable but you must treat it with care. Please pay attention to the following points:•The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock  or vibration with the power on.•Avoid using or storing the drive where it will be exposed to extreme temperatures.•Avoid using or storing the drive where it is damp or dusty.•Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.•Avoid using or storing the drive where it will be subjected to shock or vibration.•Do not disassemble or dismantle the optical drive.•Use of a commercially available lens cleaner is recommended for regular maintenance of your drive.
128 - Care and MaintenancePC CardsCaring for your Cards  PC Cards are durable, but you must treat them with care. The documentation supplied with your card will provide specific information, but you should pay attention to the following points:•To keep out dust and dirt, store cards in their protective sleeves when they are not installed in your LifeBook notebook.•Avoid prolonged exposure to direct sunlight or excessive heat.•Keep the cards dry.•Do not flex or bend the cards, and do not place heavy objects on top of them.•Do not force cards into the slot.•Avoid dropping cards, or subjecting them to excessive vibration.
129     Chapter 6    System SpecificationsSpecificationsThis section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook. Specifications of particular configurations will vary.Configuration LabelThe configuration label located on the bottom of your notebook contains specific information regarding the options you’ve chosen for your notebook. Following is an example configuration label.T2010, U7500, 12.1 WXGA, XPTE, 60G, 512MConfiguration P/N: A11XXXXXXXXXXXXFPC P/N: FPCXXXXXXHard Drive Part NumberProcessorModel #MemoryOperating System Screen Size/TypeConfiguration ID
130 - SpecificationsMicroprocessorIntel® Core™ 2 Duo Ultra Low Voltage processors (Refer to the system label to determine the speed of your processor).Chipset•Intel GM965 •I/O Controller Hub 8 Mobile (ICH8-M)MemorySystem Memory •DDR2-533 MHz SDRAM dual-channel memory module.•Two DIMM slots; upgradeable to 4 GB of total memory (2 GB x 2). Note that when 4 MB of memory is installed in a Windows Vista system, approximately 3.3 GB is addressable memory; the upper memory is reserved by Vista for hardware usage.Cache Memory 2 MB L2 cache on-dieVideoBuilt-in color flat-panel TFT active matrix LED backlight display with simultaneous display capability.Video Color and Resolution 12.1" Crystal View Wide XGA display •Internal: 1280 x 800 pixel resolution, 16M colors•External: 1600 x 1200 pixel resolution, 16M colors•Simultaneous: 1280 x 800, 16M colors
131 - SpecificationsVideo RAM Intel® Graphics Media Accelerator X3100 video graphics. Up to 384 MB shared video memory using Dynamic Video Memory Technology (DVMT) Audio•Realtek codec ALC262 with High Definition (HD) audio.•Headphones: Stereo headphone jack, 3.5 mm, 1 Vrms or less, minimum impedance 32 Ohms•Microphone: Stereo microphone jack, 3.5 mm, 100 mVp-p or less, minimum impedance 10K Ohms•One built-in speaker, 20 mm diameter•Two built-in dual digital microphonesMass Storage Device OptionsHard Drive •Serial ATA, 150 Mbps data buffer, 5400 rpm, 2.5”, 9.5 mm•Shock-mounted•Shock Sensor utilityFeaturesIntegrated Pointing Device Quick Point cursor control buttonCommunications •Gigabit LAN: Internal wired 10/100/1000 Gigabit Ethernet LAN•WLAN: Optional Integrated Intel Wireless WiFi Link 5300 (533AN_HMW), Intel Wireless WiFi Link 5100 (512AN_HMW), or, Atheros XSPAN (AR5BHB92) Wireless LAN device•Bluetooth: Optional Bluetooth device for wireless personal area network communication
132 - SpecificationsTrusted Platform Module The LifeBook T2020 has a Trusted Platform Module (TPM) installed for added system security.LifeBook Security/Application Panel Theft Prevention Lock Two lock slots for use with security restraint systems.Device PortsOn the LifeBook notebook: •PC Card slot for one Type I or Type II card: PCMCIA Standard 2.1 with CardBus support•Memory Stick/SD Card slot•One 15-pin D-SUB connector for VGA external monitor (see Display specifications)•Two USB 2.0 (Universal Serial Bus) connectors for input/output devices•One DC In connector•One IEEE 1394 (4-pin type) jack•One LAN (RJ-45) connector •Docking port (100-pin, to dock with port replicator)Button Label Button Function Default Application1Application A Notepad2Application B Calculator3Internet Internet Explorer4E-Mail OutlookFigure 26.   Application Launcher Defaults
133 - Specifications•One stereo headphone jack •One stereo microphone/line-in jack•Dedicated Smart Card slot (requires third-party application)•Wireless LAN antenna with pre-installed on/off switchOn the Optional Port Replicator: •One 15-pin D-SUB connector for VGA external monitor•Four USB 2.0 connectors for input/output devices•One LAN (RJ-45) connector •One DC-in connector•One DVI-D connector•One Line-Out connectorKeyboardBuilt-in keyboard with all functions of 101 key PS/2 compatible keyboards.•Total number of keys: 84•Function keys: F1 through F12, plus Fn extension key•Two Windows keys: one Start key, one application key •Key pitch: 19 mm; key stroke: 3.0 mm•Built-in Touchpad pointing device with two left and two right buttons and scroll button.•Quick Point cursor control button•Built-in Palm Rest•Spill-resistant•External USB keyboard/mouse support
134 - SpecificationsPowerBatteries •Standard Lithium ion battery, rechargeable, 6-cell 10.8V, 5800 mAh, or,•High capacity 9-cell Lithium ion battery, rechargeable, 10.8V, 8700 mAh AC Adapter Autosensing 100-240V AC, supplying 16V DC, 3.75A, 60W to the LifeBook; includes an AC cablePower Management Conforms to ACPI (Advanced Configuration and Power Interface).Dimensions and WeightOverall Dimensions Approximately 11.69"(w) x 8.62"(d) x 1.34”(h) (297 mm x 219 mm x 34 mm)Weight Approximately 3.31 lbs. (1.50 kg) with battery Environmental RequirementsTemperature Operating: 41° to 95° F (5° to 35° C). Non-operating: 5° to 140° F (–15° to 60° C)Humidity Operating: 20% to 85%, relative, non-condensing. Non-operating: 8% to 85%, relative, non-condensingAltitude Operating: 10,000 feet (3,048 m) maximum
135 - SpecificationsPopular AccessoriesFor ordering or additional information on Fujitsu accessories please visit our Web site at  www.shopfujitsu.com or call 1-800-FUJITSU.Pre-Installed SoftwareDepending on your pre-installed operating system, your notebook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. The following list indicates the pre-installed software on your system.•Adobe Acrobat Reader•Norton Internet Security™ 2007 (90-day free trial)•Roxio Easy Media Creator (on select models)•CyberLink PowerDVD•CyberLink PowerProducer•Google Desktop•Google Tool Bar•Google Picasa•OmniPass Fingerprint application•Fujitsu Driver Update utility•Microsoft Office Small Business Edition 2007 (60-day free trial)•Microsoft Office OneNote 2007 (on select models)•Microsoft Works 8.5 •Evernote Plus
136 - SpecificationsLearning About Your SoftwareTutorials All operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application.Manuals Included with your notebook you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included, are available online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications.Adobe Acrobat Reader The Adobe Acrobat Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms.Norton Internet Security 2007 Your system is preinstalled with a free 90-day trial version of Symantec’s Norton Internet Security™ 2007. Norton Internet Security is a suite of tools designed to protect your LifeBook notebook from computer viruses, hackers, spyware, and spam. It assists in the protection of data currently on your hard disk from destruction or contamination. The trial version is activated upon your acceptance of software license agreement. After 90 days, you will need to purchase a subscription from Symantec to download latest virus, spyware, and spam definitions.Roxio Easy Media Creator (Available with some configurations of the optional port replicator) Easy Media Creator allows you to easily burn CDs and organize, edit and share digital photos, music, data, and videos.
137 - SpecificationsCyberLink PowerDVD (Available with some configurations of the optional port replicator). PowerDVD from CyberLink is a versatile DVD player software application. PowerDVD provides high-quality video and audio playback on your system.CyberLink PowerProducer (Available with some configurations of the optional port replicator). CyberLink PowerProducer allows you to produce and edit home movies and slideshows on discs. OmniPass Fingerprint application The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass lets you use a "master password" for all Windows, applications, and on-line passwords, and presents a convenient user interface through which you can securely manage passwords, users, and multiple identities for each user.Google Desktop Google Desktop lets you to search the contents of your computer for emails, web history, and files. It also allows you to view news and photos from anywhere on your desktop.Google Picasa Google Picasa lets you to search for, locate, move and label all of the photos on your computer.Google Toolbar Google Toolbar lets you to search the Internet quickly, block pop-ups, and perform a variety of other tasks to make your Internet experience easier and more pleasant.Fujitsu Driver Update Utility The Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. See “Automatically Downloading Driver Updates” on page 120.
138 - SpecificationsMicrosoft OneNote OneNote lets you collect all of your notes and information in an electronic “notebook” so that you can organize your pictures, text, notes, and audio/video files in a single, searchable place. EverNote EverNote allows you to easily capture, store and access a variety of documents, such as typed and handwritten memos, webpage excerpts, emails, phone messages, addresses, passwords, sketches, and documents.Operating System Options Depending upon your system, one of the following operating system configurations will be installed:•Microsoft Windows XP Tablet PC Edition With Microsoft Works 8.5 and Microsoft Office 60-day trial (Small Business Edition 2007)•Microsoft Windows Vista Business Edition With Microsoft Works 8.5 and Microsoft Office 60-day trial (Small Business Edition 2007)Microsoft Works 8.5 Microsoft Works 8.5 is a software suite containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory.Microsoft Office 2007 Small Business Edition Microsoft Office 2007 Small Business Edition is easy-to-use software to help you manage business opportunities more effectively, create marketing materials, manage e-mail, and share information. Microsoft SBE includes Microsoft Word, Excel, Outlook, PowerPoint, Publisher, and Business Contact Manager.
139     GlossaryAC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook.Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power InterfaceActive-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.Ad Hoc Mode Ad Hoc Mode refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion. ADSL
140 - GlossaryAsymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines.AGP Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators.Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook notebook.BIOS Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook notebook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.Bit An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).bps An abbreviation for bits per second. Used to describe data transfer rates.Boot To start-up a computer and load its operating system from disk, ROM or other storage media into RAM.
141 - GlossaryBus An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook.Byte 8 bits of parallel binary information.Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.CardBus A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.CD-ROM Compact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.Channel Range of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.CMOS RAM Complementary metal oxide semiconductor random access memory. This is a technology for manufacturing random access memory which requires very low levels of power to operate.
142 - GlossaryCOM Port Abbreviation for communication port. This is your serial interface connection.Command An instruction which you give your operating system. Example: run a particular application or format a floppy disk.Configuration The combination of hardware and software that makes up your system and how it is allocated for use.CRT Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam.Data The information a system stores and processes.DC Direct current. A voltage or current that does not fluctuate periodically with time.Default Value A pre-programmed value to be used if you fail to set your own.DHCP Dynamic Host Configuration Protocol. A protocol used to automatically acquire parameters required for the communication, such as IP address. The sender of IP address is called a DHCP server, and the receiver is called a DHCP client.
143 - GlossaryDIMM Dual-in-line memory module.Disk A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.Disk Drive The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.Diskette A floppy disk in a hard housing with a shutter.DMA Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.DMI Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals.DNS Domain Name System. A function to control the association between the IP address and the name assigned to the computer. If you do not know the IP address but if you know the computer name, you can still communicate to that computer.
144 - GlossaryDOS Disk Operating System (MS-DOS is a Microsoft Disk Operating System).Driver A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.DVMT Dynamic Video Memory Technology. A video memory architecture that increases the efficiency of the motherboard by using innovative memory utilization and direct AGP.ECP Extended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices.Encryption Key (Network Key) Data encryption key used to encrypt message text and for computing message integrity checks. Data encryption protects data from unauthorized viewing.This device uses the same encryption key to encode and decode the data, and the identical encryption key is required between the sender and receiver.ESD Electro-Static Discharge. The sudden discharge of electricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.FCC Federal Communication Commission.
145 - GlossaryFloppy Disk A spinning platter of magnetic data storage media which is highly flexible.GB Gigabyte. One billion bytes.Hard drive A spinning platter of magnetic data storage media where the platter is very stiff.I/O Input/Output. Data entering and leaving your notebook in electronic form.I/O Port The connector and associated control circuits for data entering and leaving your notebook in electronic form.IDE Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.IEEE802.11a Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands. IEEE802.11b Wireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz ISM band.
146 - GlossaryIEEE802.11g Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11g devices operate in the 2.4 GHz ISM band. Infrared Light just beyond the red portion of the visible light spectrum which is invisible to humans.Infrastructure A name of a wireless LAN configuration. This type of communication uses an access point. Another type of communication is called Ad Hoc.IP Address An identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 1.160.10.240 could be an IP address. Within an isolated network, you can assign IP addresses at random as long as each one is unique. However, connecting a private network to the Internet requires using registered IP addresses (called Internet addresses) to avoid duplicates. The four numbers in an IP address are used in different ways to identify a particular network and a host on that network. Three regional Internet registries -- ARIN, RIPE NCC and APNIC -- assign Internet addresses from the following three classes. Class A - supports 16 million hosts on each of 126 networks Class B - supports 65,000 hosts on each of 16,000 networks Class C - supports 254 hosts on each of 2 million networks The number of unassigned Internet addresses is running out, so a new classless scheme called CIDR is gradually replacing the system based on classes A, B, and C and is tied to adoption of IPv6.
147 - GlossaryIR An abbreviation for infrared.IrDA Infrared Data Association. An organization which produces standards for communication using infrared as the carrier.IRQ Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.KB  Kilobyte. One thousand bytes.LAN Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.LCD Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.Lithium ion Battery A type of rechargeable battery which has a high power-time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.LPT Port Line Printer Port. A way of referring to parallel interface ports because historically line printers were the first and latter the most common device connected to parallel ports.
148 - GlossaryMAC Address  Media Access Control Address. A unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards. For Ethernet, frames are sent and received based on this address.MB Megabyte. One million bytes.Megahertz 1,000,000 cycles per second.Memory A repository for data and applications which is readily accessible to your LifeBook notebook’s CPU.MHz Megahertz.MIDI Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers.Modem A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.Monaural A system using one channel to process sound from all sources.
149 - GlossaryMTU Maximum Transmission UnitThe maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large.Network key Data that is used for encrypting data in data communication. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.Network name (SSID: Service Set Identifier )When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.NTSC National TV Standards Commission. The standard for TV broadcast and reception for the USA.Open system authentication Null authentication method specified in the 802.11 standard that performs no authentication checks on a wireless client before allowing it to associate.Operating System A group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of microprocessor in order to produce the desired results from that particular equipment.
150 - GlossaryPartition A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.PCMCIA PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.Peripheral Device A piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.Pitch (keyboard) The distance between the centers of the letter keys of a keyboard.Pixel The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.POST Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded. PPPoE Point to Point Protocol over Ethernet. A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line.
151 - GlossaryProgram An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.Protocol Procedures and rules use to send and receive data between computers.- Method of sending and receiving data- Process used to handle communication errorsConditions required for communication are organized in procedures for correct transfer of information.RAM Random Access Memory. A hardware component of your LifeBook notebook that holds binary information (both program and data) as long as it has the proper power applied to it.RAM Module A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.Reset The act of reloading the operating system. A reset erases all information stored in RAM.Restart See Reset.Resume To proceed after interruption. In your notebook this refers to returning to active operation after having been in one of the suspension states.
152 - GlossaryROM Read Only Memory. A form of memory in which information is stored by physically altering the material. Data stored in this way can not be changed by your notebook and does not require power to maintain it.SDRAM Synchronous Dynamic Random Access Memory.Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.Shared key authentication 802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP. If the client has the wrong key or no key, authentication will fail and the client will not be allowed to associate with the AP. Shared key authentication is not considered secure, because a hacker who detects both the clear-text challenge and the same challenge encrypted with a WEP key can decipher the key.SSID Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID. Because the SSID is broadcast in plain text, it does not supply any security to the network. Standby To make inoperative for a period of time. Your LifeBook notebook uses various suspension states to reduce power consumption and prolong the charge of your battery.
153 - GlossaryStatus Indicator A display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard.Stereo (audio) A system using two channels to process sound from two different sources.Subnet mask TCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.SVGA Super VGA.S-Video Super Video. A component video system for driving a TV or computer monitor.System Clock An oscillator of fixed precise frequency which synchronizes the operation of the system and is counted to provide time of day and date.TCP/IP Transmission Control Protocol/Internet Protocol. A standard Internet protocol that is most widely used.
154 - GlossaryTFT Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.UL Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices.USB Universal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer.VRAM Video Random Access Memory. A memory dedicated to video display data and control.WFM Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.Wi-Fi Compatible Wi-Fi (Wireless Fidelity) Identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guarantees the interoperability of wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA Web site at: www.wirelessethernet.com.WLAN Wireless Local Area Network. A wireless interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.
155 - Regulatory InformationRegulatory InformationNoticeChanges or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.FCC NOTICESNotice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet that is on a different circuit than the receiver.•Consult the dealer or an experienced radio/TV technician for help.Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device.
156 - Regulatory InformationNotice to Users of the US Telephone Network This equipment complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this information or number must be provided to the telephone company.This equipment is designed to be connected to the telephone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.The ringer equivalent number (REN) of this equipment is 0.1B as shown on the label. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operations or procedures that could effect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
157 - Regulatory InformationThe equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equipment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual.DOC (INDUSTRY CANADA) NOTICESNotice to Users of Radios and Television This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.Notice to Users of the Canadian Telephone Network  NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
158 - Regulatory InformationBefore connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.Avis Aux Utilisateurs Du Réseau Téléphonique Canadien AVIS: Le présent matériel est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal. Cette conformité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel.FOR SAFETY, USERS SHOULD ENSURE THAT THE ELECTRICAL GROUND OF THE POWER UTILITY, THE TELEPHONE LINES AND THE METALLIC WATER PIPES ARE CONNECTED TOGETHER. USERS SHOULD NOT ATTEMPT TO MAKE SUCH CONNECTIONS THEMSELVES BUT SHOULD CONTACT THE APPROPRIATE ELECTRIC INSPECTION AUTHORITY OR ELECTRICIAN. THIS MAY BE PARTICULARLY IMPORTANT IN RURAL AREAS.
159 - Regulatory Information Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.1B. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.POUR ASSURER LA SÉCURITÉ, LES UTILISATEURS DOIVENT VÉRIFIER QUE LA PRISE DE TERRE DU SERVICE D’ÉLECTRICITÉ, LES LIGNES TÉLPHONIQUES ET LES CONDUITES D’EAU MÉTALLIQUES SONT CONNECTÉES ENSEMBLE. LES UTILISATEURS NE DOIVENT PAS TENTER D’ÉTABLIR CES CONNEXIONS EUX-MÊMES, MAIS DOIVENT CONTACTER LES SERVICES D’INSPECTION D’INSTALLATIONS ÉLECTRIQUES APPROPRIÉS OU UN ÉLECTRICIEN. CECI PEUT ÊTRE PARTICULIÈREMENT IMPORTANT EN RÉGIONS RURALES.
160     Appendix A: WLAN User’s Guide FCC Regulatory InformationPlease note the following regulatory information related to the optional wireless LAN device.Regulatory Notes and StatementsWireless LAN, Health and Authorization for use  Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:•On board an airplane, or•In an explosive environment, or•In situations where the interference risk to other devices or services is perceived or identified as harmful.In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment.
161 Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operated in conjunction with any other antenna or transmitter.For IEEE 802.11a Wireless LAN: For operation within 5.15~5.25 GHz frequency range, it is restricted to indoor environments, and the antenna of this device must be integral.Federal Communications Commission statement This device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:1Reorient or relocate the receiving antenna.2Increase the distance between the equipment and the receiver.3Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.4Consult the dealer or an experienced radio/TV technician for help.Figure A-1. Ad Hoc Mode Network
162 FCC Radio Frequency Exposure statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposure have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The wireless LAN radio device has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.Export restrictions This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corp. may invalidate the user's right to operate this equipment.Canadian Notice The device for the 5150 - 5250 MHz band is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems.The maximum antenna gain of 6 dBi permitted (for devices in the 5250 - 5350 MHz, 5470 - 5725 MHz and 5725 - 5825 MHz bands) to comply with the e.i.r.p. limit as stated in A9.2 of RSS210.In addition, users are cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250 - 5350 MHz and 5650 - 5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
163 Before Using the Optional Wireless LANBefore Using the Optional Wireless LANThis manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference.Wireless LAN Device Covered by this DocumentThis document is applicable to systems containing one of the following optional devices:•Intel Wireless WiFi Link5300 (533AN_HMW)•Intel Wireless WiFi Link 5100 (512AN_HMW)•Atheros® XSPAN (AR5BHB92) Mini-Card Wireless network cardCharacteristics of the WLAN Device•The WLAN devices are Mini-PCI card attached to the main board of the mobile computer. •The WLAN devices operate in license-free RF bands, eliminating the need to procure an FCC operating license. The WLANs operate in the 2.4GHz Industrial, Scientific, and Medical (ISM) RF band and the lower, middle, and upper bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands. •The wireless devices are capable of four operating modes, IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n (draft)•The WLAN devices are Wi-Fi certified and operate (as applicable0 at a the maximum data rate of 540 Mbps (theoretical) in IEEE802.11n (draft) mode; 54 Mbps in IEEE802.11a or IEEE802.11g mode; and 11 Mbps in IEEE802.11b mode.•The WLAN devices support the following encryption methods - WEP, TKIP, CKIP, and AES encryption.•The Wireless LAN devices are compliant with the following standards: WPA, WPA2, CCX1.0, CCX2.0, CCX3.0, and CCX4.0.
164 Before Using the Optional Wireless LANWireless LAN Modes Using this DeviceAd Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers. Ad Hoc mode requires that the SSID, network authentication, and encryption key settings are identically configured on all computers in the Ad Hoc network.Figure 27.  Ad Hoc Mode Network
165 Before Using the Optional Wireless LANAccess Point (Infrastructure) Mode  Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).Figure 28.  Access Point (Infrastructure) Mode NetworkADSL modem,cable modem,or similarInternet Wired LANAccess Point*Wireless LAN *An optional hub for a wiredLAN may be required dependingupon the type of access point used.
166 Before Using the Optional Wireless LANHow to Handle This Device The WLAN device is an optional device that may come pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. •The wireless devices support IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n.•The WLAN devices operate in the 2.4 GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.•Microwave ovens may interfere with the operation of WLAN devices since they operate in the same 2.4 GHz frequency range as IEEE802.11b/g/n devices. Interference by microwaves does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.•Wireless devices that transmit in the 2.4 GHz range may interfere with operation of WLAN devices in IEEE802.11b/g/n modes. Symptoms of interference include reduced throughput, intermittent disconnects, and many frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure proper operation of the WLAN device.Deactivating/Disconnecting the WLAN DeviceDisconnecting the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). The WLAN device can be deativated by using the Wireless On/Off Switch, and it can be disconnected in Windows using the WLAN icon in the system tray (Note that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected.).BEFORE USING THE WIRELESS LAN DEVICE, YOU MUST FIRST INSTALL CLICKME! TO ENSURE THAT THE CORRECT SOFTWARE FOR YOUR DEVICE IS INSTALLED. SEE “INSTALLING CLICKME!” ON PAGE 70.
167 Before Using the Optional Wireless LANDeactivation Using the Wireless On/Off SwitchThe WLAN device can be deactivated quickly and efficiently by toggling the Wireless LAN/Bluetooth On/Off Switch to the Off position. The switch has no effect on non-Wireless LAN models.Figure 29.  Wireless LAN/Bluetooth On/Off Switch LocationDisconnection Using the Icon in the TaskbarNote that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected.1Right-click the WLAN icon in the taskbar at the bottom right of your screen.2Choose Disconnect from a network.Activating the WLAN DeviceActivation of the WLAN device can be accomplished using the same methods as the deactivation process•Using the Wireless On/Off Switch•In Windows, by right-clicking the WLAN icon then clicking “Connect to a network”WLAN/Bluetooth Switch
168 Configuring the Wireless LANConfiguring the Wireless LANThe optional WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows Vista. Support for most industry standard security solutions is contained in this software.Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters:Configuring the WLAN Using Windows Vista1Click the Start button, then select Control Panel.2If the Control Panel is not in Classic View, select Classic View from the left panel. Double-click the Network and Sharing Center icon.3Select “Manage wireless networks” from the left panel.4Click on the [Add] button.5Depending upon what type of connection you would like to make, make a selection. For an infrastructure network, select “Manually create a network profile. For ad hoc network, select “Create an ad hoc network”.6Enter the required information. It may be necessary to consult with your network administrator for some of the information.7In the event you require assistance, go to the Network and Sharing Center window (Start -> Control Panel -> Network and Sharing Center), and type in relevant keywords in the Search box. Connecting to a Network After you have configured your computer, you can connect to an active network by performing the following steps:1Click on the WLAN icon in the system tray.2Select “Connect to a network”.3Select a network from the list that appears, and click the [Connect] button.
169 Configuring the Wireless LANConfiguring the WLAN Using Windows XP Procedure 1Click the Start button, then select Control Panel.2If the Control Panel is not in Classic View, select Classic View from the left panel. Double-click the Network Connections icon.3Select “New Connection” wizard.4Click the [Next] button.5Select “Connect to the Internet”, then click [Next].6Depending upon what type of connection you would like to make, make a selection. For an infrastructure network, select “Manually create a network profile. For ad hoc network, select “Choose from a list of Internet service providers”.7Enter any required information. It may be necessary to consult with your network administrator for some of the information.8In the event you require assistance, go to [Start] -> Help and Support -> Networking and the Web. Select the main topic in which you are interested, then type in relevant keywords in the Search box. Connection to the networkAfter you have configured your computer, you can connect to an active network by clicking on the Wireless Network icon in the system tray:
170 Troubleshooting the WLANTroubleshooting the WLANTroubleshootingCauses and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. If you are unfamiliar with the steps required, consult your System Administrator or go to [Start] -> Help and Support -> Networking and the WebProblem Possible Cause Possible SolutionUnavailable network  connectionIncorrect network name (SSID) or network keyAd hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.Access Point (Infrastructure) connection: set network name (SSID) and network key to the same values as those of the access point. Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary. Weak received signal strength and/or link qualityAd hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight.Access Point (Infrastructure) connection: Retry connection after shortening the distance to the access point or removing any obstacles for better sight.The WLAN device has been deactivated or disabledCheck if the wireless switch is turned On. In Windows XP, go to Start ->  Control Panel-> Network Connections and right-click on Wireless Network Connection. If Enable appears at the top of the menu, click it to enable the device. In Windows Vista, go to Start -> Control Panel, and double-click on Windows Mobility Center. If the wireless network is off, click the [Turn wireless on] button..
171 Troubleshooting the WLANUnavailable network  connection(continued)The computer to be connected is turned offCheck if the computer to be connected is turned ON.RF interference from Access Points or other wireless networksThe use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device.Wireless network authentication has failedRe-check your Network Authentication, Encryption, and Security settings. Incorrectly configured security settings such as an incorrectly typed WEP key, a mis-configured LEAP username, or an incorrectly chosen authentication method will cause the LAN device to associate but not authenticate to the wireless network.Incorrectly configured network settingsRecheck the configuration of your network settings.Incorrect IP address configurationThis only applies to networks using static IP addresses. Please contact your network administrator for the correct settings.Problem Possible Cause Possible Solution
172 WLAN SpecificationsWLAN SpecificationsSpecificationsItem SpecificationType of network  The Intel WiFi Link 5300 (533AN_HMW), Intel WiFi Link 5100 (512AN_HMW), and Atheros XSPAN (AR5BHB92) WLAN devices conform to IEEE 802.11a, 802.11b/g,  and 802.11n (draft-compliant), Wi-Fi based*.Transfer rate (Automatic switching) 54 Mbps maximum data rate (IEEE802.11n to be determined)Active frequency •802.11n (draft): 2.4 GHz or 5 GHz•802.11b/g: 2400~2473 MHz •802.11a: 4900 ~ 5850 MHzTypical operating distances** •802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps•802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps•802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps•802.11n (draft): Estimated double the operating distance of 802.11g and 802.11a in their respective frequencies.Number of channels •802.11a: 8 independent channels•802.11b/g: 11 channels, 3 non-overlapping channels •802.11n (draft): 2.4 GHz - 3 non-overlapping channels when Channel Bonding is not used; 2 non-overlapping channels when Channel Bonding is used. 5 GHz - 12 non-overlapping UNII channels with or without Channel Bonding Security  Encryption Types - WEP, TKIP, AES***, WPA 1.0 compliant  Encryption Key lengths Supported: 64 bits and 128 bits 802.1x/EAPMaximum recommended number of computers to be connected over wireless LAN (during ad hoc connection)10 units or less ****
173 WLAN Specifications*    “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.**  The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources.*** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/   104 bits after subtracting the fixed length of 24 bits.****  Depending on practical environments, the allowable number of computers to be connected may be decreased.
174 Using the Bluetooth DeviceUsing the Bluetooth DeviceThe Integrated Bluetooth module (EYTF3CSFT) is an optional device available for Fujitsu mobile computers. What is BluetoothBluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other. Where to Find Information About BluetoothThe Bluetooth module contains a robust Help user’s guide to assist you in learning about operation of the Bluetooth device.Windows XP: To access the Help file, click [Start] -> All Programs, and click on Toshiba. Select Bluetooth, then select User’s Guide.Windows Vista: o access the Help file, click [Start] -> All Programs, and click on Bluetooth, then select User’s Guide.For additional information about Bluetooth Technology, visit the Bluetooth Web site at: www.bluetooth.com.THE WIRELESS LAN/BLUETOOTH ON/OFF SWITCH WILL POWER OFF BOTH THE OPTIONAL WIRELESS LAN AND BLUETOOTH DEVICES AT THE SAME TIME. TO ENABLE OR DISABLE EITHER ONE OF THE DEVICES INDIVIDUALLY, PERFORM THE FOLLOWING STEPS:1Slide the Wireless LAN/Bluetooth on/off switch to On position.2In the Control Panel, click the button associated with Bluetooth and/or Wireless LAN Status to enable or disable the individual devices.3Click [OK].
175 Using the Bluetooth DeviceFCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located on the front edge of the right palm rest and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.Canadian Notice To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.Warranty Users are not authorized to modify this product. Any modifications invalidate the warranty.This equipment may not be modified, altered, or changed in any way without signed written permission from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and Industry Canada and the warranty.
176     Appendix B: Fingerprint Sensor DeviceIntroducing the Fingerprint Sensor DeviceYour system has a fingerprint sensor device at the bottom left below the display screen. Figure 30.   Fingerprint sensorWith a fingerprint sensor, you can avoid having to enter a username and password every time you want to:•Log onto Windows•Resume from standby mode•Cancel a password-protected screen saver•Log into homepages that require a username and passwordFingerprintSensor Device
177 - Introducing the Fingerprint Sensor DeviceAfter you have “enrolled” - or registered - your fingerprint, you can simply swipe your fingertip over the sensor for the system recognize you. The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and on-line passwords. OmniPass requires users to authenticate themselves using the fingerprint sensor before granting access to the Windows desktop. This device results in a secure authentication system for restricting access to your computer, applications, web sites, and other password-protected resources.OmniPass presents a convenient graphical user interface, through which you can securely manage passwords, users, and multiple identities for each user.Getting StartedThis section guides you through the preparation of your system for the OmniPass fingerprint recognition application. You will be led through the OmniPass installation process. You will also be led through the procedure of enrolling your first user into OmniPass. Installing OmniPassIf OmniPass has already been installed on your system, skip this section and go directly to “User Enrollment” on page 179. You can determine whether OmniPass has already been installed by checking to see if the following are present:•The gold key-shaped OmniPass icon in the system tray at the bottom right of the screen.•The Softex program group in the Programs group of the Start menuSystem Requirements The OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows:
178 - Introducing the Fingerprint Sensor Device•Windows XP Professional operating system•At least 35 MB available hard disk spaceInstalling the OmniPass Application If OmniPass is already installed on your system, go to “User Enrollment” on page 179. Otherwise continue with this section on software installation.To install OmniPass on your system you must:1Insert the installation media for the OmniPass application into the appropriate drive. If you are installing from CD-ROM or DVD-ROM, you must find and launch the OmniPass installation program (setup.exe) from the media.2Follow the directions provided in the OmniPass installation program. Specify a location to which you would like OmniPass installed. It is recommended that you NOT install OmniPass in the root directory (e.g. C:\). 3Once OmniPass has completed installation you will be prompted to restart you system. Once your system has rebooted you will be able to use OmniPass. If you choose not to restart immediately after installation, OmniPass will not be available for use until the next reboot.4The installation program automatically places an icon (Softex OmniPass) in the Windows Control Panel as well as a golden key shaped icon in the taskbar. Verifying Information about OmniPass After you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system.To check the version information of OmniPass:•INSTALLATION OF THE APPLICATION REQUIRES THAT YOU HAVE AN EXTERNAL OPTICAL DRIVE ATTACHED TO YOUR SYSTEM.•FOR INSTALLATION, OMNIPASS REQUIRES THAT THE USER INSTALLING OMNIPASS HAVE ADMINISTRATIVE PRIVILEGES TO THE SYSTEM. IF YOUR CURRENT USER DOES NOT HAVE ADMINISTRATIVE PRIVILEGES, LOG OUT AND THEN LOG IN WITH AN ADMINISTRATOR USER BEFORE PROCEEDING WITH OMNIPASS INSTALLATION.
179 - Introducing the Fingerprint Sensor Device1From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen), or, Click the Start button, select Settings, and click Control Panel (if you are using Windows XP you will see the Control Panel directly in the Start menu; click it, then click Switch to Classic View). Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear. If it does not appear, then the program is not properly installed, or, Click the Start button, select Programs, and from the submenu select the Softex program group, from that submenu click OmniPass Control Center.2Select the About tab at the top of the OmniPass Control Panel. The About tab window appears with version information about OmniPass.Uninstalling OmniPass To remove the OmniPass application from your system:1Click Start on the Windows taskbar. Select Settings, and then Control Panel.2Double-click Add/Remove Programs.3Select OmniPass, and then click Change/Remove.4Follow the directions to uninstall the OmniPass application.5Once OmniPass has finished uninstalling, reboot your system when prompted.User EnrollmentBefore you can use any OmniPass features you must first enroll a user into OmniPass.FOR UNINSTALLATION, OMNIPASS REQUIRES THAT THE USER UNINSTALLING OMNIPASS HAVE ADMINISTRATIVE PRIVILEGES TO THE SYSTEM. IF YOUR CURRENT USER DOES NOT HAVE ADMINISTRATIVE PRIVILEGES, LOG OUT AND THEN LOG IN WITH AN ADMINISTRATOR USER BEFORE PROCEEDING WITH OMNIPASS UNINSTALLATION.
180 - Introducing the Fingerprint Sensor DeviceMaster Password Concept Computer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access. This can result in dozens of sets of credentials that you have to remember.During user enrollment a "master password” is created for the enrolled user. This master password “replaces” all other passwords for sites you register with OmniPass. Example: A user, John, installs OmniPass on his system (his home computer) and enrolls an OmniPass user with username “John_01” and password “freq14”. He then goes to his webmail site to log onto his account. He inputs his webmail credentials as usual (username “John_02” and password “lifebook”), but instead of clicking [Submit], he directs OmniPass to Remember Password. Now whenever he returns to that site, OmniPass will prompt him to supply access credentials. John enters his OmniPass user credentials (“John_01” and “freq14”) in the OmniPass authentication prompt, and he is allowed into his webmail account. He can do this with as many web sites or password protected resources he likes, and he will gain access to all those sites with his OmniPass user credentials (“John_01” and “freq14”). This is assuming he is accessing those sites with the system onto which he enrolled his OmniPass user. OmniPass does not actually change the credentials of the password protected resource. If John were to go to another computer without he OmniPass account to access his webmail, he would need to enter his original webmail credentials (“John_02” and “lifebook”) to gain access. If he attempts his OmniPass user credentials on a system other than a system he’s enrolled on, he will not gain access.
181 - Introducing the Fingerprint Sensor DeviceBasic Enrollment The Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified otherwise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard.1Click Enroll to proceed to username and password verification. By default, the OmniPass Enrollment Wizard enters the credentials of the currently logged in Windows user.2Enter the password you use to log in to Windows. This will become the “master password” for this OmniPass user. In most cases, the Domain: value will be your Windows computer name. In a corporate environment, or when accessing corporate resources, the Domain: may not be your Windows computer name. Click [Next] to continue.3In this step OmniPass captures your fingerprint. Refer to “Enrolling a Fingerprint” on page 182 for additional information.4Next, choose how OmniPass notifies you of various events. We recommend you keep Taskbar Tips on Beginner mode taskbar tips and Audio Tips on at least Prompt with system beeps only until you get accustomed to how OmniPass operates. Click [Next] to proceed with user enrollment. You will then see a Congratulations screen indicating your completion of user enrollment.5Click [Done] to exit the OmniPass Enrollment Wizard. You will be asked if you’d like to log in to OmniPass with your newly enrolled user; click [Yes].THE ENROLLMENT PROCEDURE ASSUMES YOU HAVE NO HARDWARE AUTHENTICATION DEVICES OR ALTERNATE STORAGE LOCATIONS THAT YOU WISH TO INTEGRATE WITH OMNIPASS. IF YOU DESIRE SUCH FUNCTIONALITY, CONSULT THE APPROPRIATE SECTIONS OF THIS DOCUMENT.
182 - Introducing the Fingerprint Sensor DeviceEnrolling a Fingerprint Enrolling a fingerprint will increase the security of your system and streamline the authentication procedure. You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the User Settings area. Click Enroll Authentication Device and authenticate at the authentication prompt to start device enrollment.11.During initial user enrollment, you will be prompted to select the finger you wish to enroll. Fingers that have already been enrolled will be marked by a green check. The finger you select to enroll at this time will be marked by a red arrow. OmniPass will allow you re-enroll a finger. If you choose a finger that has already been enrolled and continue enrollment, OmniPass will enroll the fingerprint, overwriting the old fingerprint. Select a finger to enroll and click [Next].22.It is now time for OmniPass to capture your selected fingerprint. It may take a several capture attempts before OmniPass acquires your fingerprint. Should OmniPass fail to acquire your fingerprint, or if the capture screen times out, click [Back] to restart the fingerprint enrollment process.   Your system has a “swipe” fingerprint sensor. A swipe sensor is small and resembles a skinny elongated rectangle. To capture a fingerprint, gently swipe or pull your fingertip over the sensor (starting at the second knuckle) towards yourself. Swiping too fast or too slow will result in a failed capture. The Choose Finger screen has a [Practice] button; click it to practice capturing your fingerprint. When you are comfortable with how your fingerprint is captured, proceed to enroll a finger.33. Once OmniPass has successfully acquired the fingerprint, the Verify Fingerprint screen will automatically appear. To verify your enrolled fingerprint, place your fingertip on the sensor and hold it there as if you were having a fingerprint captured. Successful fingerprint verification will show a green fingerprint in the capture window and the text Verification Successful under the capture window.
183 - Introducing the Fingerprint Sensor DeviceUsing OmniPassYou are now ready to begin using OmniPass. Used regularly, OmniPass will streamline your authentications.Password Replacement You will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials. OmniPass can detect these prompts and you can teach OmniPass your login credentials. The next time you go to that website, you can authenticate with your fingerprint to gain access.OmniPass Authentication Toolbar After installing OmniPass and restarting, you will notice a dialog you have not seen before at Windows Logon. This is the OmniPass Authentication Toolbar, and it is displayed whenever the OmniPass authentication system is invoked. The OmniPass authentication system may be invoked frequently: during Windows Logon, during OmniPass Logon, when unlocking your workstation, when resuming from standby or hibernate, when unlocking a password-enabled screensaver, during password replacement for remembered site or application logins, and more. When you see this toolbar, OmniPass is prompting you to authenticate.The Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not. When you click the icon for an unselected authentication method, the authentication prompt associated with that method is displayed.When prompted to authenticate, you must supply the appropriate credentials: an enrolled finger for the fingerprint capture window or your master password for the master password prompt (the key icon).Remembering a Password OmniPass can remember any application, GUI, or password protected resource that has a password prompt.
184 - Introducing the Fingerprint Sensor DeviceUsing the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint.Go to a site that requires a login (username and password), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login). Right-click the OmniPass system tray icon and select Remember Password from the submenu. The Windows arrow cursor will change to a golden key OmniPass cursor. Click the OmniPass cursor in the login prompt area, but don’t click [Login] or [Submit].Associating a Friendly Name After clicking the OmniPass key cursor near the login prompt, OmniPass will prompt you to enter a “friendly name” for this site. You should enter something that reminds you of the website, the company, or the service you are logging into. In its secure database, OmniPass associates this friendly name with this website.Additional Settings for Remembering a Site When OmniPass prompts you to enter a “friendly name” you also have the opportunity to set how OmniPass authenticates you to this site. There are three effective settings for how OmniPass handles a remembered site.The default setting is Automatically click the “OK” or “Submit” button for this password protected site once the user is authenticated. With this setting, each time you navigate to this site OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass, you will automatically be logged into the site. Less secure is the option to Automatically enter this password protected site when it is activated. Do not prompt for authentication. Check the upper box to get this setting, and each time you navigate to this site OmniPass will log you into the site without prompting you to authenticate.
185 - Introducing the Fingerprint Sensor DeviceIf you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass your credentials will be filled in to the site login prompt, but you will have to click the website [OK], [Submit], or [Login] button to gain access to the site. Click Finish to complete the remember password procedure. The site location, the credentials to access the site, and the OmniPass authentication settings for the site are now stored in the OmniPass secure database. The OmniPass authentication settings (Settings for this Password Site) can always be changed in Vault Management.Logging in to a Remembered Site Whether or not OmniPass prompts you to authenticate when you return to a remembered site is determined by Settings for this Password Site and can be changed in Vault Management. The following cases are applicable to using OmniPass to login to: Windows, remembered web sites, and all other password protected resources.With Master Password Once you return to a site you have remembered with OmniPass, you may be presented with a master password prompt. Enter your master password and you will be allowed into the site.THIS SETTING IS MORE CONVENIENT IN THAT WHENEVER YOU GO TO A SITE REMEMBERED WITH THIS SETTING, YOU WILL BYPASS ANY AUTHENTICATION PROCEDURE AND GAIN INSTANT ACCESS TO THE SITE. BUT SHOULD YOU LEAVE YOUR SYSTEM UNATTENDED WITH YOUR OMNIPASS USER LOGGED IN, ANYONE USING YOUR SYSTEM CAN BROWSE TO YOUR PASSWORD PROTECTED SITES AND GAIN AUTOMATIC ACCESS.
186 - Introducing the Fingerprint Sensor DeviceLogging into Windows with a Fingerprint Device When logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.In Windows XP, your login options must be set either for classic login, or for fast user switching and logon screen to be enabled to use your fingerprint to log on to Windows. To change this go to Control Panel, select User Accounts and then click Change the way users log on or off. If your Windows screensaver is password protected, the fingerprint capture window will now appear next to screensaver password dialog during resume. You can authenticate to your screensaver password prompt with your enrolled finger.Password Management OmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Vault Management; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Passwords under Vault Settings. You will see the Manage Passwords interface, with a list of friendly names.You can view the credentials stored for any remembered website by highlighting the desired resource under Password Protected Dialog and clicking Unmask Values. Should a password be reset, or an account expire, you can remove stored credentials from OmniPass. Highlight the desired resource under Password Protected Dialog and click Delete Page. You will be prompted to confirm the password deletion.IF A MACHINE IS LOCKED AND OMNIPASS DETECTS A DIFFERENT USER LOGGING BACK IN WITH A FINGERPRINT, THE FIRST USER WILL BE LOGGED OUT AND THE SECOND USER LOGGED IN.
187 - Introducing the Fingerprint Sensor DeviceThe two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site.OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site. The exception to the above rule is when resetting the Windows password. If your password is reset in Windows, the next time you login to Windows, OmniPass will detect the password change and prompt you to “Update” or “Reconfirm” the password with OmniPass. Enter your new Windows password in the prompt and click OK. Your OmniPass "master password" will still be your Windows password.OmniPass User Identities Identities allow OmniPass users to have multiple accounts to the same site (e.g., bob@biblomail.com and boballen@biblomail.com). If OmniPass did not provide you identities, you would be limited to remembering one account per site.To create and manage identities, double-click the OmniPass key in the system tray. Click Vault Management; OmniPass will prompt you to authenticate. Once you gain access to Vault Management, click Manage Identities under Vault Settings. You can only manage the identities of the currently logged in OmniPass userTo add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply]. You can now switch to the new identity and start remembering passwords.To delete an identity, highlight the identity you want to delete and click [Delete Identity], then click [Apply].WHEN YOU DELETE AN IDENTITY, ALL OF ITS ASSOCIATED REMEMBERED SITES AND PASSWORD PROTECTED DIALOGS ARE LOST.
188 - Introducing the Fingerprint Sensor DeviceTo set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automatically be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password".Choosing User Identity during Login To choose your identity during login, type your username in the User Name: field. Press [Tab] and see that the Domain: field self-populates. Click the Password: field to bring the cursor to it, and you will see the pull-down menu in the Identity: field. Select the identity to login as, then click OK.Switch User Identity To switch identities at any time, right-click the OmniPass system tray icon and click Switch User Identity from the submenu. The Switch Identity dialog will appear. Select the desired identity and then click OK.Identities and Password Management On the Manage Passwords interface of the Vault Management tab of the OmniPass Control Center, there is a pull-down selection box labeled, Identity. This field lets you choose which identity you are managing passwords for. When you select an identity here, only those password protected dialogs that are associated with that identity are shown. You can perform all the functions explained in “Password Management” on page 186.
189 - Introducing the Fingerprint Sensor DeviceConfiguring OmniPassThis section gives an overview of both the Export/Import function and the OmniPass Control Center. Exporting and Importing Users Using OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported. Exporting an OmniPass User Profile To export a user, open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Exports an OmniPass user profile. OmniPass will prompt you to authenticate. Upon successfully authentication, you must name the OmniPass user profile and decide where to save it. An .opi file is generated, and you should store a copy of it in a safe place.YOU CANNOT IMPORT A USER INTO OMNIPASS IF THERE ALREADY IS A USER WITH THE SAME NAME ENROLLED IN OMNIPASS. •YOU SHOULD PERIODICALLY EXPORT YOUR USER PROFILE AND STORE IT IN A SAFE PLACE. IF ANYTHING HAPPENS TO YOUR SYSTEM, YOU CAN IMPORT YOUR OMNIPASS PROFILE TO A NEW SYSTEM AND HAVE ALL YOUR REMEMBERED SETTINGS AND FINGERPRINTS INSTANTLY.•YOU DON'T FORGET THE WINDOWS LOGIN CREDENTIALS WHEN EXPORTING. WHEN YOU EXAMINE THE IMPORTATION, YOU ARE PROMPTED FOR AUTHENTICATION. THE CREDENTIALS THAT WILL ALLOW A USER PROFILE TO BE IMPORTED ARE THE WINDOWS LOGIN CREDENTIALS OF THE EXPORTED USER. THEY ARE THE CREDENTIALS THAT HAD TO BE SUBMITTED WHEN THE USER PROFILE WAS EXPORTED. YOU WILL NEED USER NAME, PASSWORD, AND DOMAIN.
190 - Introducing the Fingerprint Sensor DeviceThis .opi file contains all your user specific OmniPass data, and it is both encrypted and password protected. This user profile does NOT contain any of your encrypted data files.Importing an OmniPass User Profile To import an OmniPass user open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Imports a new user into OmniPass and then select OmniPass Import/Export File (*.opi) and click Next. OmniPass will then prompt you to browse for the file you had previously exported (.opi file). When you select the .opi file for importation, OmniPass will prompt you for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name.OmniPass will notify you if the user was successfully imported.Things to Know Regarding Import/Export •Assume you export a local Windows User profile from OmniPass. You want to import that profile to another machine that has OmniPass. Before you can import the profile, a Windows user with the same login credentials must be created on the machine importing the profile.  Example: I have a Windows user with the username “Tom” and the password “Sunshine” on my system. I have enrolled Tom into OmniPass and remembered passwords. I want to take all my passwords to new system. I export Tom’s OmniPass user profile. I go to my new system and using the Control Panel I create a user with the username "Tom" and the password "Sunshine". I can now successfully import the OmniPass user data to the new system.•If you export an OmniPass-only user, you can import that user to any computer running OmniPass, provided that a user with that name is not already enrolled in OmniPass. •If you attempt to import a user profile who has the same name as a user already enrolled in OmniPass, the OmniPass import function will fail.
191 - Introducing the Fingerprint Sensor DeviceOmniPass Control CenterThis section will serve to explain functions within the OmniPass Control Center that weren’t explained earlier. You can access the OmniPass Control Center any of three ways:•Double-click the golden OmniPass key shaped icon in the Windows taskbar (typically in the lower-right corner of the desktop)•Click the Start button; select the Programs group; select the Softex program group; and click the OmniPass Control Center selection.•Open the Windows Control Panel (accessible via Start button --> Settings --> Control Panel) and double-click the Softex OmniPass icon.User Management The User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/Export User functionality is documented in “Exporting and Importing Users” on page 189. Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard. The Enrollment Wizard is documented in “User Enrollment” on page 179. If you click Removes a user from OmniPass, OmniPass will prompt you to authenticate. Authenticate with the credentials (or enrolled fingerprint) of the user you wish to remove. OmniPass will prompt you to confirm user removal. Click OK to complete user removal.REMOVING A USER WILL AUTOMATICALLY DESTROY ALL OMNIPASS DATA ASSOCIATED WITH THAT USER. ALL IDENTITIES AND CREDENTIALS ASSOCIATED WITH THE USER WILL BE LOST.IF YOU’RE SURE YOU WANT TO REMOVE THE USER, WE RECOMMEND YOU EXPORT THE USER PROFILE.
192 - Introducing the Fingerprint Sensor DeviceUser Settings The User Settings tab has four interfaces: Audio Settings, Taskbar Tips, and Enrollment. User settings allow users to customize OmniPass to suit their individual preferences. Under User Settings (Audio Settings and Taskbar Tips) you can set how OmniPass notifies the user of OmniPass events (e.g., successful login, access denied, etc.). The details of each setting under the Audio Settings and Taskbar Tips interfaces are self-explanatory.The Enrollment interface allows you to enroll fingerprints. For the procedure to enroll and authentication device refer to Chapter 2.3. To enroll additional fingerprints, click Enroll Authentication Device, and authenticate with OmniPass. Select the fingerprint recognition device in the Select Authentication Device screen (it should already be marked by a green check if you have a finger enrolled) and click Next.System Settings The OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon.The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass. This setting is appropriate for an office setting or any setting where users must enter a username and password to log into a computer. This is the default setting.With the second option, Manually log on to OmniPass at startup, OmniPass will prompt you to login once you have logged on to Windows.With the third option, Do not log on to OmniPass at startup, OmniPass will not prompt for a user to be logged on.You can manually log on to OmniPass by right-clicking the OmniPass taskbar icon and clicking Log in User from the right-click menu.
193 - Introducing the Fingerprint Sensor DeviceTroubleshootingYou cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and passwordCannot add Windows users to OmniPass If you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local security settings. You can do this by going to Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Network Access: Sharing and Security Model for Local Accounts. The correct setting should be Classic - Local Users Authenticate as Themselves.Cannot add a User with a Blank Password to OmniPas If you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the procedure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure.Click Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Accounts: Limit local account use of blank passwords to console login only. This setting should be set to Disabled.Dialog appears after OmniPass authentication during Windows Logon After installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box.This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). This could happen for any of the following reasons:•Your Windows password has changed•Your Windows account has been disabled
194 - Introducing the Fingerprint Sensor DeviceIf you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password.Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.
195     IndexAAbout This Guide 1, 13ACadapter 62plug adapters 124Air Vents 27, 29Anti-theft lock slot 27Auto/Airline Adapter 62Automatically Downloading Driver Updates 119BBattery 76care 124cold-swapping 79conserving power 71dead 103faulty 103hot-swapping 79increasing life 125level indicator 30lithium ion battery 76low 78problems 103, 104recharging 77replacing 79shorted 79Standby mode 78Battery Latches 28BIOSguide 66setup utility 65BluetoothWhere to Find Information 173Boot Sequence 64Booting the System 66Built-in Speakers 97Button Icons 49, 51CCapsLock 31CD-ROM 97, 98Click Me! 69Clicking 40Configuration Label 128Contact Information 14Controls and Connectors 17Conventions Used in the Guide 13Cursor Keys 37DDC in connector 17DC Output Cable 62DC Power Jack 24, 62Device Ports 89DIMM 86
196 Display Panel 20, 32brightness 34opening 33problems 105, 106Dock port 18Docking Port 89Double-Clicking 40Dragging 41Drivers and Application Restore CD 113Dual Built-in Microphones 21DVD driveproblems 97, 98EError Messages 108External Floppy Disk Driveproblems 99External Monitor Port 92External Video Port 27External Video port 18FFDU 70, 119, 136Fingerprint Sensor 21Fingerprint Sensor Device 175enrolling a fingerprint 181getting started 176installing OmniPass 176logging into a remembered site 184OmniPass authentication toolbar 182password replacement 182remembering a password 182uninstalling OmniPass 178user enrollment 178using OmniPass 182Fujitsu Contact Information 14Fujitsu Driver Update utility 70, 119, 136Fujitsu LifeBookcleaning 123storing 123traveling 123Fujitsu Shopping Online 15Function KeyF10 38F3 38F4 38F6 38F7 38F8 38, 47F9 38, 47FN 38GGigabit LAN (RJ-45) Jack 26Glossary 138HHard Disk Driveaccess indicator 31problems 99Hard Disk Drive Passwords 64Headphone Jack 17, 24, 92Hibernation Feature 73disable/enable 73IIEEE 1394 (4-pin) Jack 25IEEE 1394 Port 91Internal LAN Jack 89
197 KKeyboard 20, 36cursor keys 37function keys 37numeric keypad 37problems 99windows keys 37LLeft Button 21LifeBook Security Paneloperating 56passwords 55setting up 54uninstalling 58LifeBook Security/Tablet PC Buttons 48LifeBook SecurityTablet PC Buttons 20Lithium ion Battery Bay 28Local Area Network (LAN) 18MMedia Playercare 126Memorycapacity 88checking capacity 88compartment 29, 86installing 86problems 100removing 88upgrade module 86Memory Stickinstalling 82removing 82Memory Stick/SD Card Slot 21Memory Stick/Secure Digital Cards 81Microphone Jack 17, 25, 92Microsoft Works 137Modem problems 100Mouse problems 99NNumLk 31Oot 68PPC Cardcare 127problems 101slot 22PC Card Eject Button 22PC Cards 83installing 84removing 84PCMCIA Card slot 17Pen 25installing a pen tether 46Pen tether 46Pen Tether Attachment Point 25Pen/Pen Holder 25Pointing Device 39Port Replicatorconnector 29problems 98Post-logon button functions 52Power
198 AC adapter 61Auto/Airline adapter 61failure 101, 102management 71off 75on 63problems 104sources 61Power Management 71Power On Self Test 63, 108Power/Suspend/Resume Button 20, 71Pre-Installed Software 134Adobe Acrobat Reader 135Google Toolbar 136manuals 135Pre-logon button functions 49QQuick Pointclicking 40control adjustment 42Quick Point Cursor Control 21Quick Point Pointing Device 39RRegistration 69Regulatory Information 154Restarting 74Restoring Your Pre-installed Software 113Right Button 20RJ-45 89SScrLk 31Scroll Button 21Scrolling 41SD Cardinstalling 82removing 82SD/Memory Stick Slot 17SDRAM 29, 86Secure Digital Cardremoving 82Security ButtonsFunctions 48Security Indicator 31Security lock slot 18Sleep Mode 71Smart Card Reader 85Smart Card Slot 17Speaker 20Specifications 128Audio 130Chipset 129Device Ports 131Dimensions and Weight 133Environmental Requirements 133Keyboard 132mass storage device options 130Memory 129Microprocessor 129Power 133Video 129Standby Mode 72Status Indicator Panel 20, 30Suspend/ Resume button 18TTablet Configuration 33
199 Tablet PC Button Functionschanging 53Touch Screen 42calibrating 44clicking 43dragging 44Troubleshooting 94UUniversal Serial Bus Ports 90USB 90, 100problems 100, 101USB 2.0 Ports 24, 26USB Port 17VVolume control 47WWarranty 15Windows keys 37Application key 37Start keys 37Windows Power Management 74Windows Vistaconfiguring the WLAN 167restoring the Operating System 116starting the first time 67Windows XPconfiguring the Wireless LAN 168restoring the Operating System 114starting the first time 68Wireless LANBefore Using the Wireless LAN 162configuring 162connection to the network 168deactivating/disconnecting 165modes 163Specifications 171Troubleshooting 169Wireless LAN/Bluetooth On/Off Switch 22

Navigation menu