Fujitsu Client Computing WL0006 WLAN (WLL4030) in LifeBook T Series T3010D User Manual Appendix O

Fujitsu Limited WLAN (WLL4030) in LifeBook T Series T3010D Appendix O

Host PC User Manual

FCC ID: EJE-WL0006     (IC: 337J-WL0006)                                    Report No.  M040222_Cert_Mace_Atheros_5.2    EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au    EMC Technologies Report Number: M040222_Cert_Mace_Atheros_5.2      APPENDIX O1 – Host PC User Manual
CopyrightCopyrightFujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.The following are registered trademarks of Microsoft Corporation: MS, MS-DOS, Windows.PCMCIA is a trademark of the Personal Computer Memory Card International Association.Intel and Pentium are registered trademarks of Intel Corporation.Adobe Acrobat Reader is a registered trademark of Adobe System Inc.PowerQuest and Drive Image are registered trademarks of PowerQuest Corporation.All other trademarks mentioned herein are the property of their respective owners.© Copyright 2003 Fujitsu PC Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu PC Corporation. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu PC Corporation.B5FH-9011-01EN-00DECLARATION OF CONFORMITYaccording to FCC Part 15Responsible Party Name: Fujitsu PC CorporationAddress:  5200 Patrick Henry DriveSanta Clara, CA  95054Telephone: (408) 982-9500Declares that product: Model Configuration:LifeBook T3010 Tablet PC LifeBook T3010D Tablet PCComplies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:(1) This device must not be allowed to cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.T Series.book  Page 1  Thursday, July 31, 2003  10:49 AM
LifeBook T Series Tablet PCT Series.book  Page 2  Thursday, July 31, 2003  10:49 AM
Table of ContentsFujitsu LifeBook® T Series Tablet PCTable of Contents1PREFACEPrefaceAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . .3FPC Contact Information . . . . . . . . . . . . . . . . . . .3Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32GETTING TO KNOWYOUR TABLET PCOverviewUnpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Optional Accessories  . . . . . . . . . . . . . . . . . . . . . .8Locating the Controls and ConnectorsTop and Front Components . . . . . . . . . . . . . . . .10Left-Side Panel Components  . . . . . . . . . . . . . . .11Right-Side Panel Components  . . . . . . . . . . . . . .12Rear Panel Components . . . . . . . . . . . . . . . . . . .13Bottom Components  . . . . . . . . . . . . . . . . . . . . .14Status Indicator PanelPower Indicator . . . . . . . . . . . . . . . . . . . . . . . . .15AC Adapter Indicator . . . . . . . . . . . . . . . . . . . . .15Battery Level Indicators  . . . . . . . . . . . . . . . . . . .15Battery Charging Indicator . . . . . . . . . . . . . . . . .16Hard Drive Access Indicator . . . . . . . . . . . . . . . .16NumLk Indicator. . . . . . . . . . . . . . . . . . . . . . . . .16CapsLock Indicator. . . . . . . . . . . . . . . . . . . . . . .16ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .16Security Indicator . . . . . . . . . . . . . . . . . . . . . . . .16Display PanelOpening the Display Panel . . . . . . . . . . . . . . . . .17Using the System as a Tablet . . . . . . . . . . . . . . .17Adjusting Display Panel Brightness . . . . . . . . . . .18KeyboardUsing the Keyboard . . . . . . . . . . . . . . . . . . . . . .19Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . .19Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .19Cursor Keys  . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . .20LifeBook Security/Tablet PC ButtonsChanging Tablet PC Button Functions  . . . . . . . .22Setting up LifeBook Security Panel . . . . . . . . . . .22Passwords  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Using Your LifeBook Security Panel  . . . . . . . . . .23Uninstalling the Security Panel Application . . . . . 24Touchpad Pointing DeviceClicking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . .25Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Touchpad Control Adjustment . . . . . . . . . . . . . .26Pen and Active DigitizerUsing the Pen. . . . . . . . . . . . . . . . . . . . . . . . . . .27Calibrating the Pen. . . . . . . . . . . . . . . . . . . . . . .27Replacing the Pen Tip. . . . . . . . . . . . . . . . . . . . .28Using the Active Digitizer . . . . . . . . . . . . . . . . . .28Volume ControlControlling the Volume  . . . . . . . . . . . . . . . . . . .293USING YOUR TABLET PCPower SourcesConnecting the Power Adapters . . . . . . . . . . . . .33Starting Your Tablet PCPower On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . .34BIOS Setup Utility. . . . . . . . . . . . . . . . . . . . . . . .34Booting the System  . . . . . . . . . . . . . . . . . . . . . .34T Series.book  Page 3  Thursday, July 31, 2003  10:49 AM
LifeBook T Series Tablet PCActivating Additional Utilities . . . . . . . . . . . . . . . 35Registering Your LifeBook T Series Tablet PC . . . 35Power ManagementSuspend/Resume Button . . . . . . . . . . . . . . . . . . 36Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 36Hibernate Mode. . . . . . . . . . . . . . . . . . . . . . . . . 37Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . 37Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . 37Windows Power Management. . . . . . . . . . . . . . 37Restarting the System. . . . . . . . . . . . . . . . . . . . . 37Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384USER-INSTALLABLE FEATURESLithium ion BatteryRecharging the Battery. . . . . . . . . . . . . . . . . . . . 41Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 42Memory Upgrade ModuleInstalling Memory Upgrade Modules . . . . . . . . . 43To Remove a Memory Upgrade Module  . . . . . . 43Checking the Memory Capacity . . . . . . . . . . . . . 44PC CardsInstalling PC Cards . . . . . . . . . . . . . . . . . . . . . . . 45Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . 45Smart Card Reader. . . . . . . . . . . . . . . . . . . . . . . 45Port ReplicatorRear Panel Components. . . . . . . . . . . . . . . . . . . 46Front Panel Components . . . . . . . . . . . . . . . . . . 47Attaching the Port Replicator . . . . . . . . . . . . . . . 47Detaching the Port Replicator. . . . . . . . . . . . . . . 47Device PortsModem (RJ-11) Jack  . . . . . . . . . . . . . . . . . . . . . 48Internal LAN (RJ-45) jack . . . . . . . . . . . . . . . . . . 48Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . 48Infrared Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 49Headphone Jack. . . . . . . . . . . . . . . . . . . . . . . . . 49External Monitor Port. . . . . . . . . . . . . . . . . . . . . 495TROUBLESHOOTINGTroubleshootingIdentifying the Problem . . . . . . . . . . . . . . . . . . . 53Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . 53Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 54Power On Self Test Messages  . . . . . . . . . . . . . . 61Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 62Restoring Your Pre-installed SoftwareDrive Image Special Edition (DISE) . . . . . . . . . . . 636CARE AND MAINTENANCECare and MaintenanceLifeBook T Series Tablet PC . . . . . . . . . . . . . . . . 67Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Optional Floppy Disk Drive and Floppy Disks. . . 68Optional CD Drive and CDs. . . . . . . . . . . . . . . . 68PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697SPECIFICATIONSSpecificationsConfiguration Label . . . . . . . . . . . . . . . . . . . . . . 73Physical Specifications . . . . . . . . . . . . . . . . . . . . 73Processing Specifications . . . . . . . . . . . . . . . . . . 73Memory/Storage Specifications . . . . . . . . . . . . . 73Display Specifications. . . . . . . . . . . . . . . . . . . . . 73Interface Specifications  . . . . . . . . . . . . . . . . . . . 73Power Specifications  . . . . . . . . . . . . . . . . . . . . . 74Environmental Specifications . . . . . . . . . . . . . . . 74Agency Approval Specifications . . . . . . . . . . . . . 74Additional Specifications  . . . . . . . . . . . . . . . . . . 74Regulatory Information . . . . . . . . . . . . . . . . . . . 75T Series.book  Page 4  Thursday, July 31, 2003  10:49 AM
Table of Contents8GLOSSARYGlossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81APPENDIX:INTEGRATED WIRELESSLAN USER’S GUIDEFCC Regulatory Information. . . . . . . . . . . . . . . .89Before Using the Wireless LANFor Better Communications  . . . . . . . . . . . . . . . .91Stopping Transmission . . . . . . . . . . . . . . . . . . . .92Starting Transmission . . . . . . . . . . . . . . . . . . . . .92Connection Using Windows XPFlow of Operations. . . . . . . . . . . . . . . . . . . . . . .93Preparation for Wireless LAN Connection. . . . . .93Connection to the Network . . . . . . . . . . . . . . . .95Other settingsSetting of Power-saving Function. . . . . . . . . . . .99TroubleshootingTroubleshooting the Wireless LAN . . . . . . . . . .100IP address informationAbout IP Addresses  . . . . . . . . . . . . . . . . . . . . .102SpecificationsWireless LAN Specifications . . . . . . . . . . . . . . .103T Series.book  Page 5  Thursday, July 31, 2003  10:49 AM
LifeBook T Series Tablet PCT Series.book  Page 6  Thursday, July 31, 2003  10:49 AM
11PrefaceT Series.book  Page 1  Thursday, July 31, 2003  10:49 AM
2LifeBook T Series Tablet PCT Series.book  Page 2  Thursday, July 31, 2003  10:49 AM
3PrefacePrefaceABOUT THIS GUIDEThe LifeBook® T Series Tablet PC from Fujitsu PC Corporation is a powerful convertible computer. It can be used either as a standard notebook using keyboard input, or in tablet configuration using pen input. It is powered by an Intel® microprocessor, has a built-in color display with an active digitizer, and brings the computing power of desktop personal computers (PCs) to a portable and versatile environment.This manual explains how to operate your LifeBook T Series Tablet PC’s hardware and built-in system soft-ware. Your LifeBook T Series Tablet PC is compatible with the IBM® PC AT, and it comes with Windows® XP Tablet Edition pre-installed.Your LifeBook T Series Tablet PC is a completely self-contained unit with an active-matrix (TFT) color LCD display. It has a powerful interface that enables it to support a variety of optional features. Conventions Used in the GuideKeyboard keys appear in brackets. Example: [Fn], [F1], [Esc], [Enter] and [Ctrl].Pages with additional information about a specific topic are cross-referenced within the text.Example: (See page xx.)On screen buttons or menu items appear in bold.Example: Click OK to restart your Tablet PC.DOS commands you enter appear in Courier type. Example: Shutdown the computer?FPC CONTACT INFORMATIONService and SupportYou can contact FPC Service and Support the following ways:■Toll free: 1-800-8Fujitsu (1-800-838-5487)■Fax: 1-408-764-2724 ■E-mail: 8fujitsu@fujitsupc.com ■Web site: http://www.fujitsupc.comBefore you place the call, you should have the following information ready so that the customer support representative can provide you with thefastest possible solution:■Product name■Product configuration number■Product serial number■Purchase date■Conditions under which the problem occurred■Any error messages that have occurred■Hardware configuration■Type of device connected, if anyFujitsu OnlineYou can go directly to the online Fujitsu Product catalog for your Tablet PC. Go to Start -> All Programs -> Service & Support Software, and click on Pen Accesso-ries Web site.You can also reach Fujitsu Service and Support online by going to Start -> All Programs -> Service & Support Software, and clicking on Fujitsu Service & Support Web site.WARRANTYYour LifeBook T Series Tablet PC is backed by an Inter-national Limited Warranty and includes toll-free tech-nical support. Check the service kit that came with yourTablet PC for warranty terms and conditions.The information icon highlights information that will enhance your understanding of the subject material.The caution icon highlights information that is important to the safe operation of your computer, or to the integrity of your files. Please read all caution information carefully.The warning icon highlights information that can be hazardous to either you, your LifeBook T Series Tablet PC, or your files. Please read all warning information carefully.You must have an active internet connection to use the online URL links.T Series.book  Page 3  Thursday, July 31, 2003  10:49 AM
4LifeBook T Series Tablet PC - PrefaceT Series.book  Page 4  Thursday, July 31, 2003  10:49 AM
52Getting to KnowYour Tablet PCT Series.book  Page 5  Thursday, July 31, 2003  10:49 AM
6LifeBook T Series Tablet PCT Series.book  Page 6  Thursday, July 31, 2003  10:49 AM
7Getting to Know Your Tablet PC Figure 2-1. Fujitsu LifeBook T Series Tablet PC OverviewThis section describes the components of your Fujitsu LifeBook T Series Tablet PC. We strongly recommend that you read it before using your Tablet PC, even if you are already familiar with mobile computers.UNPACKINGWhen you receive your LifeBook T Series Tablet PC, unpack it carefully, and compare the parts you have received with the items listed below.For a pre-configured model you should have:■LifeBook T Series Tablet PC (Figure  2-1)■AC adapter with AC power cord (Figure  2-2)■Phone/Modem (RJ-11) telephone cable■Pen (located in pen holder)■Driver and Application Restore (DAR) CD■Getting Started Guide■User’s Guide (this document)■International Limited Warranty Booklet■Microsoft Windows Manual and Certificate of Authenticity■Lithium ion battery (pre-installed)You may also have one or more of the following optional devices in the box:■Port Replicator (Figure  2-3)■External USB Floppy Disk Drive■External DVD/CD-ROM Combo Drive■External USB CD-ROM Drive Figure 2-2. AC AdapterFigure 2-3. Optional Port ReplicatorT Series.book  Page 7  Thursday, July 31, 2003  10:49 AM
8LifeBook T Series Tablet PC - Section 2OPTIONAL ACCESSORIESThe following optional accessories can be used with the LifeBook T Series Tablet PC. Refer to the instructions provided with these accessories for details on their use. For the latest list of accessories available for your LifeBook T Series Tablet PC, be sure to frequently check the Fujitsu Web site at: www.fujitsupc.comTable 2-1.  Optional Accessories for LifeBook T Series Tablet PCPeripheral/Accessory Fujitsu Part NumberDocking Options LifeBook T Series Tablet PC port replicator FPCPR39APCarrying CasesDuo Travel Bag FPCCC16Director leather carrying case FPCCC22Diplomat carrying case FPCCC02Propak backpack FPCCC07Storage OptionsExternal USB floppy disk drive  FPCFDD12External DVD/CD-RW combo drive FPCDVR26External CD-ROM drive FPCCD33APMemory256 MB SDRAM, DDR266 FPCEM51AP512 MB SDRAM, DDR 266 FPCEM55AP1.0 GB SDRAM, DDR 266 FPCEM87AP128 MB Compact Flash card FPCEMC02256 MB Compact Flash card FPCEMC03128 MB Secure Digital memory card FPCEMC01Power OptionsAC Adapter with US cord FPCAC23Main battery FPCBP73APAuto/airline adapter FPCAA02Battery charger FPCBC06Input AccessoriesReplacement pen set (2-pack) FPCPN11APUSB optical mouse FPCMO08APAdditional AccessoriesSmart Card holder FPCSCH01Wireless LAN card, 802.11b FPCWL08Compact Flash card adapter FPCCFA01Notebook Guardian Lock FPCLCK02Logitech wireless keyboard and mouse FPCKB04 T Series.book  Page 8  Thursday, July 31, 2003  10:49 AM
9Getting to Know Your Tablet PCLocating the Controls and ConnectorsConnectors and peripheral interfaces on the LifeBook T Series Tablet PC and the optional port replicator allow you to connect a variety of devices. Specific locations are illustrated in Figures 2-4 through 2-8. The table below provides a short description of each icon on the Life-Book T Series Tablet PC. Each of the icons is either molded into or printed on the Tablet PC chassis. Table 2-2.  System iconsConnection Tablet PC Icon PurposeDC in connector Connect an external power source such as the AC adapter or auto/airline adapter. USB Port Connect Universal Serial Bus 2.0 or 1.1 compliant devices to the Tablet PC. PCMCIA Card slot      Install Type I, Type II, or Type III PC Cards.Microphone jack Connect an external microphone. The internal microphone is disabled when you plug in an external microphone. Headphone jack Connect stereo headphones or powered external speakers. The internal speaker is disabled when you plug in external headphones or powered speakers. IrDA/FIR port  An infrared transceiver built into the Tablet PC allows you to communicate with other devices that are compliant with IrDA Standard Rev. 1.1. Effective range for infrared communication is about 3 feet, and within 15 degrees off center. A clear line-of-sight path must exist between the IrDA port on the computer and the IrDA transceiver on the other device.Modem Connect a telephone line to the internal modem using a standard RJ-11 telephone plug.Tablet Dock port Connect the LifeBook T Series Tablet PC port replicator or other approved docking device. Refer to documentation accompanying the docking device for more information.Security lock slot The security slot allows you to secure the Tablet PC using Kensington-compatible locking devices.Suspend/Resume buttonThe Suspend/Resume button allows you to suspend Tablet PC activity without powering off, resume your Tablet PC from suspend mode, and power on the system when it has been shut down from Windows. Local Area Network (LAN)The LAN (RJ-45) jack is used to connect the internal Fast Ethernet (10/100 Base-T/TX) to a Local Area Network (LAN) in your office or home, or broadband devices such as a cable modem, DSL, or satellite Internet. Battery Release LatchThe battery release latch allows you to remove the battery from your system for storage or replacement.Wireless LAN On-Off SwitchThe wireless LAN switch allows you to turn power to the optional wireless LAN device on and off.T Series.book  Page 9  Thursday, July 31, 2003  10:49 AM
10LifeBook T Series Tablet PC - Section 2Figure 2-4. LifeBook T Series Tablet PC with display openTOP AND FRONT COMPONENTSThe following is a brief description of the top and front features of the LifeBook T Series Tablet PC. (Figure  2-4)Pen/Pen HolderThe pen is used as the interface with the active digitizer display.Closed Cover SwitchThe closed cover switch turns off the LCD back lighting when the display panel is closed. Display Panel LatchThe display panel latch locks and releases the display panel. Status Indicator PanelThe Status Indicator Panel displays symbols that corre-spond to specific components of your LifeBook T Series Tablet PC. See “Status Indicator Panel” on page 15.LifeBook Security/Tablet PC ButtonsThe LifeBook T Series Tablet PC Security/Tablet PC Buttons provide hardware security and application launch capabilities. See “LifeBook Security/ Tablet PC Buttons” on page 21.Touchpad Pointing DeviceThe Touchpad pointing device consists of two mouse-like buttons and one scroll button. See “Touchpad Pointing Device” on page 25.KeyboardA full-function keyboard with dedicated Windows keys. See “Keyboard” on page 19.Display PanelThe display panel is a color LCD panel with back lighting for the display of text and graphics and active digitizer functionality. Rotation HingeThe rotation hinge allows you to transform your Tablet PC from a notebook configuration into a tablet configu-ration. For more information, see See “Using the System as a Tablet” on page 17.Display StatusKeyboardLifeBook TouchpadScroll ButtonIndicatorPanelPanelDisplay PanelLatchRotationHingeClosedCoverSwitchSecurity/PointingDeviceSpeakerPen/Pen HolderTablet PCButtonsT Series.book  Page 10  Thursday, July 31, 2003  10:49 AM
11Getting to Know Your Tablet PCFigure 2-5. LifeBook T Series Tablet PC left-side panelLEFT-SIDE PANEL COMPONENTSFollowing is a brief description of your Tablet PC’s left-side components. (Figure  2-5)PC Card SlotsThe PC Card Slots allow you to install two Type II or one Type III PC Card. The PC Card Eject Button is used when ejecting a PC Card from the slot. See “PC Cards” on page 45.Headphone JackThe headphone jack allows you to connect headphones or powered external speakers. See “Headphone Jack” on page 49.Microphone JackThe microphone jack allows you to connect an external mono microphone. See “Microphone Jack” on page 49.PC Card SlotsPC Card Eject/Lock ButtonAir VentsHeadphone JackMicrophone JackT Series.book  Page 11  Thursday, July 31, 2003  10:49 AM
12LifeBook T Series Tablet PC - Section 2Figure 2-6.  LifeBook T Series Tablet PC right-side panelRIGHT-SIDE PANEL COMPONENTSFollowing is a brief description of your Tablet PC’s right-side components. Suspend/Resume ButtonThe Suspend/Resume button allows you to suspend Tablet PC activity without powering off, resume your Tablet PC from standby mode, and power on your system when it has been shut down from the Windows operating system. See “Power On” on page 34.Modem (RJ-11) Telephone PortThe Modem (RJ-11) telephone port is for attachinga telephone line to the internal multinational 56K modem. Anti-theft Lock SlotThe anti-theft lock slot allows you to attach a optional physical lock-down device. Modem (RJ-11) PortSuspend/Resume ButtonAnti-theft Lock SlotThe internal multinational modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook T Series Tablet PC. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000 bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600 bps at upload. T Series.book  Page 12  Thursday, July 31, 2003  10:49 AM
13Getting to Know Your Tablet PCFigure 2-7. LifeBook T Series Tablet PC rear panelREAR PANEL COMPONENTSDC Power JackThe DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your Tablet PC and charge the internal Lithium ion Battery. External Monitor PortThe external monitor port allows you to connect an external VGA or SVGA CRT monitor. Note that when the optional Port Replicator is attached to the system, you must use the external monitor port on the Port Replicator rather than the port on the system. See “External Monitor Port” on page 49.USB 2.0 PortsThe two USB 2.0 ports allow you to connect Universal Serial Bus devices. See “Universal Serial Bus Ports” on page 48.Infrared PortThe fast IrDA compatible port allows you to communi-cate with another IrDA compatible infrared device without a cable. LAN (RJ-45) JackThe internal LAN (RJ-45) port is used for an internal Fast Ethernet (10/100 Base-T/TX) connection. See “Internal LAN (RJ-45) jack” on page 48.Built-in MicrophoneThe built-in microphone allows mono audio input. WLAN On/Off SwitchThe wireless LAN On/Off Switch is used to power off the wireless antenna when not in use.Infrared PortWLAN On/Off SwitchDC Power JackExternal Monitor PortLAN (RJ-45) JackUSB 2.0 PortsBuilt-in Microphone(cover removed)T Series.book  Page 13  Thursday, July 31, 2003  10:49 AM
14LifeBook T Series Tablet PC - Section 2Figure 2-8. LifeBook T Series Tablet PC bottom panelBOTTOM COMPONENTSFollowing is a brief description of your Tablet PC’s bottom panel components. (Figure  2-8)Lithium ion Battery CompartmentThe battery compartment contains the internal Lithium ion battery. The battery should be removed when the computer is stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery. See “Lithium ion Battery” on page 41.Port Replicator ConnectorThis connector allows you to connect the optional port replicator. Main Unit and Configuration LabelThe configuration label shows the model number and other information about your LifeBook T Series Tablet PC. In addition, the configuration portion of the label has the serial number and manufacturer information that you will need to give your support representative. It identifies the exact version of various components of your Tablet PC. Memory Upgrade CompartmentYour Tablet PC comes with high speed Synchronous Dynamic RAM (SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your Tablet PC, hence improving overall performance. See “Memory Upgrade Module” on page 43.Memory UpgradeCompartmentLithium ionBatteryMain Unit andConfigurationLabel (approximateBatteryPort ReplicatorConnectorlocation)PackLatchBatteryPackLatchCompartmentT Series.book  Page 14  Thursday, July 31, 2003  10:49 AM
15Getting to Know Your Tablet PCFigure 2-9. Status Indicator PanelStatus Indicator PanelThe Status Indicator Panel displays symbols that corre-spond to specific components of your LifeBook T Series Tablet PC. These symbols tell you how each of those components is operating. (Figure 2-9)POWER INDICATORThe Power indicator symbol states whether your system is operational. It has several different states, each of which tells you what mode your Tablet PC is in at that time.■Steady On: This means that there is power to your Tablet PC and that it is ready for use.■Flashing: This means that your Tablet PC is in Standby mode.■Steady Off: This means that your system is either in Hibernate mode, or that your Tablet PC has been turned off.If you are charging your battery, the Power indicator symbol will remain on even if your LifeBook T Series Tablet PC is shut off. The Power indicator symbol will also remain on if you have either adapter connected and are shut down from Windows.AC ADAPTER INDICATORThe AC adapter indicator states whether your notebook is operating from the AC adapter, the auto/airline adapter or the batteries. This icon has two different states that can tell you what power source your LifeBook notebook is using.■On: This means that either of the adapters are currently in use.■Off: Power is only coming from the batteries, andyou do not have an adapter connected.BATTERY LEVEL INDICATORSThe Battery Level indicators state whether or not the Lithium ion battery is installed and how much charge is available within the battery. (Figure 2-10)Additionally, this indicator displays when an overcur-rent is detected. If an overcurrent is detected, the battery stops charging and the Battery Level indicator blinks at the rate of once per second. To stop the indicator from blinking, you must disconnect the power adapter.A1BatteryLevel Hard DriveAccessBatteryCharging NumLkScrLkSecurityIndicatorCapsLkPowerAC AdapterT Series.book  Page 15  Thursday, July 31, 2003  10:49 AM
16LifeBook T Series Tablet PC - Section TwoFigure 2-10.  Battery Level IndicatorBATTERY CHARGING INDICATORLocated to the left of the Battery Level indicator is a small arrow symbol. This symbol states whether the battery is charging. This indicator will flash if the battery is too hot or cold to charge.HARD DRIVE ACCESS INDICATORThe Hard Drive Access indicator states whether your internal hard drive is being accessed.NUMLK INDICATORThe NumLk indicator states that the integral keyboard is set in ten-key numeric keypad mode. If there is no battery activity and the power adapters are not connected, the Battery Level indicators will also be off.CAPSLOCK INDICATORThe CapsLock indicator states that your keyboard is set to type in all capital letters. SCRLK INDICATORThe ScrLk indicator states that your scroll lock is active. SECURITY INDICATORThe Security Indicator flashes (if a password was set) when the system resumes from Off or Standby modes. You must enter the password that was set in the Security Panel before your system will resume operation.A shorted battery is damaged and must be replaced. (Figure 2-10) If there is no battery activity and the power adapters are not connected, the Battery Level indicators will also be off.Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged.76%–100% Charging76%–100%51%–75%26%–50%11%–25%Low Warning <11%Critical Low or Dead BatteryShorted BatteryIf you are using the optional external numerical keypad, pressing the [NumLk] key will activate the external keypad. The indicator will come on, however it will not change any of the functionality of your keyboard keys.T Series.book  Page 16  Thursday, July 31, 2003  10:49 AM
17Getting to Know Your Tablet PCFigure 2-11. Opening the displayDisplay PanelYour LifeBook T Series Tablet PC contains a display panel that is backlit for easier viewing in bright environ-ments. The convertible design of your Tablet PC allows you to open the display fully, rotate it 180 degrees, and lay it face up on the keyboard. This allows you to use the system as a tablet, much as you would a pad of paper.OPENING THE DISPLAY PANEL1. Slide the latch release to the right. This releases the locking mechanism. While holding the latch release, lift display cover.2. Lift the display backwards, being careful not to touch the screen, until it is at a comfortable viewing angle. (Figure 2-11)USING THE SYSTEM AS A TABLETIf you would like to use the system as a tablet, perform the following steps. 1. Lift the display until it is perpendicular to the keyboard. (Figure 2-13).2. When the display is perpendicular to the keyboard, rotate it clockwise (when viewed from the top). Be very careful to rotate it in the direction indicated. (Figure 2-14). Turn the display 180 degrees so that it is facing backwards. (Figure 2-15)3. Holding the top edge of the display panel, pull it forward until it is lying nearly atop the keyboard.4. Push the latch towards the display (See "A" in Figure 2-12). The latch will pivot so the top latch disappears, and the bottom latch appears (See "B" in Figure 2-12). Holding the latch down, lay the display flush against the system so that the latch engages. You can now use your system as a tablet. (Figure 2-16)Figure 2-12. Latching/Unlatching5. To return the system to notebook configuration, repeat step 3 and 2. Be sure to turn the display in the opposite direction when performing step 2.Figure 2-13. Fully open displayDisplay Panel LatchLatch ReleaseRotate the system display only in the direction indicated in the procedure. Turning the display in the incorrect direction could cause hinge damage.In the following step, be sure to position the display perpendicular to the keyboard, otherwise the keyboard or display cover could get scratched.ABTop latchBottom latchDisplay Side90oT Series.book  Page 17  Thursday, July 31, 2003  10:49 AM
18LifeBook T Series Tablet PC - Section TwoFigure 2-14. Rotating the displayFigure 2-15. Display rotated completelyFigure 2-16. System in tablet configurationADJUSTING DISPLAY PANEL BRIGHTNESSOnce you have turned on your Tablet PC, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness, keyboard and power management utility. Using Keyboard to Adjust BrightnessAdjusting the brightness using the keyboard changes the system setting (i.e., the settings you make via the func-tion keys automatically changes the brightness settings in the system’s Pen and Tablet Settings). ■[Fn+F6]: Pressing repeatedly will lower the brightness of your display.■[Fn+F7]: Pressing repeatedly will increase thebrightness of the display.Using Power Management to Adjust BrightnessTo adjust brightness with the power management utility, click Start -> Control Panel -> Tablet and Pen Settings. Select the Display tab and set the screen brightness slider for battery and AC power scenarios.Using the Fujitsu Menu to Adjust BrightnessTo adjust brightness using the Fujitsu menu, click on the Fujitsu Menu icon in the system tray in the lower right corner of the screen. From the menu that appears, select Brightness Control. The Tablet and Pen Settings window will open. Select the Display tab and set the screen brightness slider for battery and AC power scenarios.  If using AC power your brightness setting is set to its highest level by default. If using battery power your brightness settings is set to approximately mid-level by default.The higher the brightness level, the more power the LifeBook T Series Tablet PC will consume and the faster your batteries will discharge. For maximum battery life, make sure that the brightness is set as low as possible.T Series.book  Page 18  Thursday, July 31, 2003  10:49 AM
19Getting to Know Your Tablet PCFigure 2-17.  KeyboardKeyboardUSING THE KEYBOARDYour LifeBook T Series Tablet PC has an integral 83-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys. (Figure 2-17)■Numeric keypad: Your Tablet PC allows certain keys to serve dual purposes, both as standard characters and as numeric and mathematical keys. The ability to tog-gle between the standard character and numerical keys is controlled through the [NumLk] key.■Cursor keys: Your keyboard contains four arrowkeys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. ■Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. ■Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.NUMERIC KEYPADCertain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] key. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ),multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary func-tions. (Figure 2-17) WINDOWS KEYSYour LifeBook T Series Tablet PC has two Windows keys: a Start key and an Application key. The Start key displays the Start menu. This button functions the same as your onscreen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows documentation for additional information regarding the Windows keys.) (Figure 2-17)Fn Key Start KeyFunction KeysNumeric KeypadApplication KeyCursor Keys(outlined with thickblack line)If you are using the optional external numerical keypad, pressing the [NumLk] key will activate the external keypad. The indicator will come on, however it will not change any of the functionality of your keyboard keys. T Series.book  Page 19  Thursday, July 31, 2003  10:49 AM
20LifeBook T Series Tablet PC - Section TwoCURSOR KEYSThe cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left, and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right). (Figure 2-17)FUNCTION KEYSYour Tablet PC has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documen-tation to find out how these keys are used. (Figure 2-17)[Fn] KeyThe [Fn] key provides extended functions for theTablet PC and is always used in conjunction with another key. ■[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.■[Fn+F4]: Pressing [F4] while holding [Fn] will toggle the built-in pointing device on and off. Note that the [Fn+F4] combination only works if Manual Setting is selected in the BIOS. (See “Entering the BIOS Setup Utility” on page 34)■[Fn +F5]: Pressing [F5] while holding [Fn] allows you to toggle between video compensation and no compensation. (Video compensation controls spacing on the display. When it is enabled, displays with less than 1024 x 768 or 800 x 600 pixel resolution will still cover the entire screen.)■[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display. Note that adjusting the brightness using the keyboard changes the system setting.■[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.■[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your Tablet PC.■[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your Tablet PC.■[Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, both built-in display panel, and external monitor or external moni-tor only.T Series.book  Page 20  Thursday, July 31, 2003  10:49 AM
21Getting to Know Your Tablet PCFigure 2-18.  LifeBook T Series Tablet PC Security/Tablet PC Buttons LifeBook Security/Tablet PC ButtonsA unique feature of your LifeBook T Series Tablet PC is the array of Security and Tablet PC buttons. These buttons allow you to secure your Tablet PC from unauthorized use and to launch specific applications with the touch of a button. If the security system is activated, upon starting your Tablet PC or resuming from Standby, Hibernate, or shut-down mode the security system will require you to enter a password code using the security buttons. After you enter the correct password, your Tablet PC will resume operation. The five security/Tablet PC buttons are located on the bottom right-hand side of the display when it is config-ured to be used as a notebook. (Figure 2-18) Security functions: All five buttons are used when implementing security functions. Four of the buttons are used to enter the password, and the fifth is used as an Enter button. See the right-hand column of Table 2-3.Tablet PC funct io n s :  All five of the buttons have primary functions. Four of the buttons have secondary functions when used as application buttons. The secondary functions are activated by pressing the Func-tion (Fn) button while pressing the application button. See Table 2-3 for specific functions. The secondary func-tions of the Application A and B buttons can be changed to launch any application. See “Changing Tablet PC Button Functions” on page 22 Table 2-3. Security/Tablet PC Button Functions(1) Application A Button(3) Button 3(2) Application B Button(4) Button 4Enter ButtonWhen the system is logging on or when it is locked (i.e., when you have the Logon or Computer Locked window showing on your desktop), the A and B buttons act as [Tab] and [Enter] keys, respectively. Button Icon  Primary Function Secondary Function(Fn + Button)Security Panel Function(Pre-boot and resuming from suspend)Page Down User-defined Application A(Default = Calculator) Security Button 1Page Up User-Defined Application B(Default = MS Journal) Security Button 2Screen Rotation VGA-Out Security Button 3Secondary Function Selection Fujitsu Menu Utility Security Button 4Ctl+Alt+Del Button None Security Enter ButtonT Series.book  Page 21  Thursday, July 31, 2003  10:49 AM
22LifeBook T Series Tablet PC - Section TwoPage Down / Application A ButtonWhen you press the Page Down button when the system is running, each press of the button will scroll the screen down one frame. This allows you to navigate quickly through large documents.When you press the Fn button while you press then release the Page Down/Application A button, you will automatically start whichever program is assigned to the button. The default application for this button is Calcu-lator.See “Changing Tablet PC Button Functions” on page 22 to select a different application for this button.Page Up / Application B ButtonWhen you press the Page Up button when the system is running, each press of the button will scroll the screen up one frame. This allows you to navigate quickly through large documents.When you press the Fn button while you press then release the Page Up/Application A button, you will auto-matically start whichever program is assigned to the button. The default application for this button is Microsoft Journal.See “Changing Tablet PC Button Functions” on page 22 to select a different application for this button.Screen Rotation / VGA-Out ButtonThe screen rotation feature would normally be used only when the system is configured as a tablet. When you would like to use the tablet as an eBook, for example, you would use the portrait orientation; when accessing spreadsheets or using the system as a notebook, you would more typically use landscape orientation.When the system is changed to tablet configuration, the orientation automatically changes to portrait mode by default. When you press the Screen Rotation / VGA-Out button, the system screen orientation changes from portrait (vertical) to landscape (horizontal) or from landscape to portrait. Function / Fujitsu Menu Utility ButtonThe Function button works in conjunction with the other application buttons to provide additional func-tionality for the buttons. Refer to specific details above.Pressing the Fn button twice in succession causes the Fujitsu Menu Utility to appear on your screen, allowing you to modify certain system settings.Ctl+Alt+Del ButtonPressing and holding the Ctl-Alt-Del button for up to 750 msecs launches the Logon screen or the Windows Task Manager (if the system hasn’t yet been configured).CHANGING TABLET PC BUTTON FUNCTIONSThe Application A and B buttons can be changed to launch a program or perform an action you select. By default, the Application A button launches the Calcu-lator, and the Application B button launches MS Journal.To launch different applications or cause the Application A or B buttons to perform a specific action:1. Double-click on the Tablet and Pen Settings icon in the Control Panel. 2. Select the Tablet Buttons tab and select the button you would like to change from the list.3. Click [Change] and open the drop down list in the Action: field.4. Select the action you would like the button to perform. If you want to launch a program, click on Launch an Application then browse to the location of the program.5. Click [OK], then click [OK] again. The buttons will now perform the actions you have assigned to them.SETTING UP LIFEBOOK SECURITY PANELWhen you receive your Tablet PC, the security panel application is pre-installed without any passwords. The following sections provide detailed information on your security panel, how to set, change or remove passwords.Numbered ButtonsUse these buttons to enter your password.(Figure 2-18)Enter ButtonAfter entering the button strokes, push this button to enter the password into the Tablet PC. (Figure 2-18)PASSWORDSThe user and supervisor password may be set on this Tablet PC. A supervisor password is typically the same for all Tablet PC’s and notebooks in a work group, office, or company to allow for system management. Individual computers in a group environment should not use a common password. A password consists of one to five button strokes plus the enter button. A valid stroke consists of pushing one or up to four buttons simulta-neously. The screen orientation default can be changed by going to the Control Panel and double-clicking on the Fujitsu Display Control icon and selecting the desired defaults from the Display Orientation section. After changing the defaults, click [OK]. T Series.book  Page 22  Thursday, July 31, 2003  10:49 AM
23Getting to Know Your Tablet PCThe following are valid button strokes: ■Pushing [4] by itself■Pushing [2] and [3] at the same time■Pushing [1], [2], and [4] at the same time■Pushing [1], [2], [3], and [4] at the same timeThe following are valid passwords. The numbers within braces ({  }) are button strokes using more than one button. ■{[2]+[3]}, [1], [Enter]■[4], [enter]■{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]Setting PasswordsWhen shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the super-visor password before the user password. Setting Supervisor PasswordYou must have set a supervisor password before setting any user passwords. The supervisor password can bypass the user password.1. Go to the Start menu.2. Click on Run.3. Type in:C:\Program Files\Fujitsu\Security Panel Application\Supervisor\ FJSECS.EXE, then press [Enter]4. Follow the on-screen instructions to set theSupervisor password.Setting User Password1 Go to the Start menu.2. Click on All Programs.3. Click on Security Panel Application -> Security Panel Application.4. Follow the on-screen instructions to set theuser password.USING YOUR LIFEBOOK SECURITY PANELThe security lock feature is in effect both when the system resumes from Off, Standby, or Hibernation state. You always need to push the Security Panel buttons to input the user password. Your system will not begin the boot sequence until you enter your supervisor/user password.From Off State1. Turn on your system.2. When the Security Indicator flashes, enter the pass-word and press Enter button.For example, if the password is 22222, first press Button 2 five times and press the Enter button. The Tablet PC will boot to normal operation.From Standby/Hibernation State1. Press your Suspend/Resume button.2. When the Security Indicator flashes, enter the pass-word and press Enter button.The Tablet PC should resume normal operation.Incorrect Password EntryIf an invalid supervisor or user password is entered three times in succession, the system will “beep” for about one minute. If a valid password is entered within a minute (while system beeps), the beeping will stop and the Tablet PC will resume normal operation. If no password is entered or an invalid password is entered while the system beeps, the system will return to its previous locked state (standby or off) and the Security Indicator will go off. To reactivate the Tablet PC after a password failure, you must press the Suspend/Resume button, then enter a correct password.PRECAUTIONSOpening and Closing the CoverBy default, closing the cover automatically places your system into Standby mode. (You can change the action the system takes when the cover is closed by opening the Power Options Properties icon in the Control Panel, and selecting the Advanced tab. Make a choice from the drop down menu for “When I close the lid of my portable computer:” and click the [OK] button.) Opening the cover does not automatically place the Tablet PC into normal operation. Instead, you must enter the proper security password after pushing the Suspend/Resume button.■The purpose of supervisor password is to be able to bypass the user password in case the user password is forgotten. The supervisor password alone will not lock the system.■You must set the supervisor and user passwords for the security panel to work.You may change or remove the supervisor or user password by repeating the steps defined above.Remember the user password you specified on the Security Panel Application. If you forget the password you will not be able to use your computer. The supervisor pass-word can override the user password.T Series.book  Page 23  Thursday, July 31, 2003  10:49 AM
24LifeBook T Series Tablet PC - Section TwoLow Battery OperationsIf your Tablet PC has a low battery, pushing the suspend/resume button only turns on the Security Indicator. Your Tablet PC does not unlock, the Security Indicator turns off after one minute. To resume normal operation, first attach a power supply to the Tablet PC. Then you may unlock the Tablet PC.UNINSTALLING THE SECURITY PANEL APPLICATIONYou have two options when uninstalling the securitypanel application:■Remove passwords and uninstall the security panel application software. This will disable all security features.■Uninstall the security panel application with password still active. This will not allow any changes to the password. Uninstalling the Security Panel Application SoftwareRemove passwords when User wants no password protection whatsoever and doesn’t want to give anybody the utility to set a password on their computer. In this case, if passwords (supervisor, user, or both) are set, the passwords must first be cleared BEFORE removing the application. To clear passwords, follow same procedure in SETTING PASSWORD CODES except this time, select REMOVE, enter current password then click Next. When asked to confirm select Ye s .Removing Security Panel Application withPasswords Still ActiveUsing this feature will not allow any changes tothe password. User: 1. Go to Start -> Control Panel.2. Open Add or Remove Programs Properties in the Control Panel. 3. Select the Security Panel Application in the list, and click Change/Remove. 4.  When the Confirm File Deletion box appears,click Ye s .Supervisor:1. Go to Start -> Control Panel.2. Open Add or Remove Programs Properties in the Control Panel. 3. Select the Security Panel Application forSupervisor in the list, and click Change/Remove. 4. When the Confirm File Deletion box appears,click Ye s .Reinstalling the Security Panel ApplicationTo reinstall supervisor or user security application, you will need your Drivers and Applications CD. The Utilities\Security Panel Application folder contains two separate folders: Supervisor and User. The setup files for supervisor and user security applications are contained in those folders. 1.  Go to the Utilities\Security Panel Applica-tion\Supervisor folder on the CD and double-click the setup.exe file. The Installing Security Panel Application window will appear. Follow the instruc-tions on the screen.2.  Go to the Utilities\Security Panel Application\User folder on the CD and double-click the setup.exe file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.Supervisor and user passwords can be set via Windows software using the FJSECS.exe and FJSECU.exe files, respectively. FJSECU.exe for the user password cannot run without first setting a supervisor password. You need to run FJSECS.exe first to set the supervisor pass-word. Follow instructions under Setting Passwords on page 23.If you forget both passwords, please contact Fujitsu PC Corporation Service and Support at 1-800-8FUJITSU (1-800-838-5487). Fujitsu PC Corporation charges a service fee for unlocking a password-restricted Tablet PC. When calling please have a valid credit card and provide proof of ownership. You will then be given instructions on where to ship your Tablet PC. Removing the applications does not remove the password. It simply removes the utility to change/add/remove passwords. To change your password you must reinstall the application.T Series.book  Page 24  Thursday, July 31, 2003  10:49 AM
25Getting to Know Your Tablet PCFigure 2-19. Touchpad pointing deviceTouchpad Pointing DeviceThe Touchpad pointing device built into your Tablet PC is used to control the movement of the cursor to select items on your display panel. The Touchpad is composed of a cursor control, left and right buttons, and a scroll button. The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger. The left and right buttons function the same as left and right mouse buttons. The scroll button allows you to navigate through pages quickly without using the scroll bars. The actual functionality of the buttons may vary depending on the application that is being used. (Figure 2-19)CLICKINGClicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the cursor to the item you wish to select, press the right button once, and then immedi-ately release it. (Figure 2-20)Figure 2-20.  ClickingDOUBLE-CLICKINGDouble-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, pressand release the left button twice. (Figure 2-21)Figure 2-21.  Double-clickingLeft ButtonRight ButtonScroll ButtonCursor Control■If the interval between clicks is too long, the double-click will not be executed.■Parameters for the Touchpad can be adjusted from the Mouse dialog box located in the Windows Control Panel.T Series.book  Page 25  Thursday, July 31, 2003  10:49 AM
26LifeBook T Series Tablet PC - Section TwoDRAGGINGDragging means pressing and holding the left button while moving the cursor. To drag, move the cursor tothe item you wish to move. Press and hold the left button while moving the item to its new locationand then release it. (Figure 2-22)Figure 2-22.   DraggingSCROLLINGUsing the scroll button allows you to navigate through a document quickly without having to use the scroll bars. This is particularly useful when you are navigating through online pages. To use the scroll button, press the raised horizontal line at the top or bottom of the button to scroll up or down a page. When you have reached the desired section of the page, release the button. (Figure 2-23)Figure 2-23.   ScrollingTOUCHPAD CONTROL ADJUSTMENTThe Windows Control Panel allows you to customize your Touchpad with selections made from within the Mouse Properties dialog box. There are several aspects of Touchpad operation, which you can adjust.To access the Mouse Properties window, open the Control Panel and double-click the Mouse icon. In the window that appears, you will see a variety of different mouse functions that you can change.T Series.book  Page 26  Thursday, July 31, 2003  10:49 AM
27Getting to Know Your Tablet PCPen and Active DigitizerUSING THE PENYou can use the LifeBook T Series Tablet PC pen to generate and create electronic “ink”, to select items, and to navigate through programs on the Tablet PC. Programs that support handwriting recognition also allow you to write characters directly on the screen with the pen. You can also use the pen as a drawing tool.Figure 2-24. LifeBook T Series PenThe screen reacts when the pen tip is approximately 1/8 inch (3-5 mm) from the screen. The pen has three switches: a tip switch and a barrel button toggle switch with switches at both ends. By default, the tip switch corresponds to the left mouse button, and the front toggle (closest to the pen tip) barrel button switch corre-sponds to the right mouse button (when used in combi-nation with the tip switch). The rear toggle of the barrel button switch acts as an electronic ink "eraser".The functions of the rear toggle and the tip click pres-sure can be changed by clicking [Start] -> Control Pane, and double-clicking the Fujitsu Pen Settings icon. To change the rear toggle function, select the drop-down list to select a new function, then click [Apply]. If you don’t want the rear toggle to have any function, select Ignore from the list. Adjusting the click pressure determines how much pres-sure must be put on the pen tip in order for the screen to react. The softer it is set, less pressure is required; the harder it is set, more pressure is required. To change the click pressure, use the slider bar to make the click pres-sure harder or softer, then click [Apply]. Here are some hints that may help you use the pen more effectively:• To activate the tip switch, tap or hold the pen tip against the screen.• To activate the barrel button switch, press and hold the end of the button you wish to use (front toggle is the right mouse button switch; the rear toggle acts as an electronic “eraser”).• To move the cursor, hold the pen tip within 1/8 inch (3 - 5 mm) from the screen and move the pen.• To start a program, double-tap the pen tip (tap the pen tip twice rapidly) on the program icon as you would double-click a mouse.•To select an object, tap the pen tip on the object once. •To double-click an object, quickly tap the object twice.CALIBRATING THE PENIn order to ensure accurate tracking between the pen and cursor, you must run the Touch Screen Calibration Utility before you use the active digitizer for the first time, or after you change the display resolution.To run the calibration utility:1. Go to Start -> Control Panel and double-click on the Tabl et and Pen S ettin gs icon. 2. Click Calibrate.3. Adjust the display of your Tablet PC to a comfort-able angle.You are advised to use a screen protector on your system display to minimize the chance of its being scratched. Screen protectors are available from the Fujitsu Web site at www.fujitsupc.com. The LifeBook T Series Tablet PC pen is a  high-quality electronic instrument that can be damaged if used improperly. Treat the pen as you would any precision device. Observe the following guidelines:• Do not gesture with the pen, use it as a pointer, or tap it on surfaces other than the Tablet PC screen.• Do not try to turn the thumb grip on the pen; it is designed for inserting and removing the pen from the pen holder.• Never store the pen with the tip bearing the weight of the pen (e.g., sitting tip down in a pencil cup). Storing the pen tip down could distort the internal mechanism over a period of time (especially in higher temperatures), causing the tip to act as if it is always depressed. The pen should be stored in the pen holder when not in use.Tip SwitchBarrel SwitchUse only the pen provided with your Tablet PC. Do not use substitutes that were not designed for the LifeBook T Series Tablet PC.T Series.book  Page 27  Thursday, July 31, 2003  10:49 AM
28LifeBook T Series Tablet PC - Section Two4. Using the pen, firmly touch the screen directly on the (+) symbol; the (+) symbol will move to the next location.5. Repeat step 4 in the four corners, then click OK.REPLACING THE PEN TIPWith use, the pen tip may become worn or may pick up foreign particles that can scratch the screen. A damaged or worn tip may not move freely, causing unpredictable results when using the pen. If your pen exhibits these problems, you should replace the pen tip. To do so, use the pen tip removal tool included with your pen.Figure 2-25. Tip Removal ToolTo remove the tip, position the tip in the gap between the two ends of the tool (Figure 2-25). Pinch the tool together so the tip is firmly clasped, then pull it from the barrel. If the tip is worn or damaged, discard it.To replace the tip, retrieve one of the new tips that accompanied your pen. Insert the flat end of the tip into the barrel and push it in firmly until it is seated.If you need more tips, they can be ordered from the Fujitsu Web site at: www.fujitsupc.com.USING THE ACTIVE DIGITIZERThe integrated active digitizer allows you to use the included pen as a pointing device. You can use the pen to click, double-click, drag items and icons, or to draw like a pen or pencil in applications that support this behavior, such as drawing or painting programs. See the documentation that came with your application for details. (Figure 2-26)Figure 2-26. Using the pen with the screenClickingTo left-click, touch the object you wish to select and then lift the pen tip immediately. (Figure 2-27)To right-click, press the front button on the barrel switch or touch the pen to the screen for a couple of seconds until the right mouse icon appears at the tip.Figure 2-27. Clicking the screenDouble-ClickingTo double-click, touch the item twice, and then immedi-ately remove the pen tip. (Figure 2-28)Figure 2-28. Double-clicking the screenGapTo avoid potential scratching and damage, never use anything but the included pen with the display. To purchase additional or replacement pens, visit the Fujitsu accessories Web site at: http://www.fujitsupc.com.■If the interval between taps is too long, the double-click will not be executed.■Parameters for the screen can be adjusted from the Mouse Properties dia-log box located in the Windows Control Panel.T Series.book  Page 28  Thursday, July 31, 2003  10:49 AM
29Getting to Know Your Tablet PCVolume ControlYour Fujitsu Tablet PC has multiple volume controls which interact with each other. CONTROLLING THE VOLUMEThe volume can be controlled in several different ways:■Volume can be set from within the Volume Control on the Taskbar.■Volume can be controlled with the [F8] and [F9] func-tions keys. Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your Tablet PC. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your Tablet PC.■Volume can be controlled by many volume controls that are set within individual applications.■Certain external audio devices you might connect to your system may have hardware volume controls.■Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources. We recommend that you experiment with the various volume controls to discover the optimal sound level.Any software that contains audio files will also contain a volume control of its own. If you install an external audio device that has an independent volume control, the hardware volume control and the software volume control will interact with each other. It should be noted that if you set your software volume to Off, you will override the external volume control setting. There are twenty-six levels through which the function keys cycle. T Series.book  Page 29  Thursday, July 31, 2003  10:49 AM
30LifeBook T Series Tablet PC - Section TwoT Series.book  Page 30  Thursday, July 31, 2003  10:49 AM
313Using Your Tablet PCT Series.book  Page 31  Thursday, July 31, 2003  10:49 AM
32LifeBook T Series Tablet PC - Section ThreeT Series.book  Page 32  Thursday, July 31, 2003  10:49 AM
33Getting StartedFigure 3-1. Connecting the AC AdapterPower SourcesYour LifeBook T Series Tablet PC has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.CONNECTING THE POWER ADAPTERSThe AC adapter or optional Auto/Airline adapter provides power for operating your Tablet PC and charging the battery. Connecting the AC Adapter1. Plug the DC output cable into the DC power jackof your Tablet PC.2. Plug the AC adapter into an AC electrical outlet. (Figure 3-1)Connecting the Optional Auto/Airline Adapter1. Plug the DC output cable into the DC power jackon your Tablet PC.2. Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key inthe On or Accessories position.OR3. Plug the Auto/Airline adapter into the DC power jack on an airplane seat.Switching from AC Adapter Power or theAuto/Airline Adapter to Battery Power1. Be sure that you have a charged battery installed.2. Remove the AC adapter or the Auto/Airline adapter.DC Power PlugDC Output CableAC AdapterAC CableThe Lithium ion battery is not charged upon purchase. Initially, you will need to connect either the AC adapter or the Auto/Airline adapter to use your Tablet PC.T Series.book  Page 33  Thursday, July 31, 2003  10:49 AM
34LifeBook T Series Tablet PC - Section ThreeStarting Your Tablet PCPOWER ONThe Suspend/Resume button is used to turn on your LifeBook T Series Tablet PC from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your Tablet PC. (See figure 2-6 on page 12 for location)Press the Suspend/Resume button to start your system. When you are done working you can either leave your Tablet PC in Standby mode, See “Standby Mode” on page 36, or you can turn it off. See “Power Off” on page 38When you Power On your Tablet PC, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your Tablet PC will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 61 Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.After satisfactory completion of the Power On Self Test (POST), your Tablet PC will load your operating system.BOOT SEQUENCEThe procedure for starting-up your Tablet PC is termed the Bootup sequence and involves your Tablet PC’s BIOS. When your Tablet PC is first turned on, the main system memory is empty, and it needs to find instruc-tions to start up your Tablet PC. This information is in the BIOS program. Each time you power up or restart your Tablet PC, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your Tablet PC is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.The boot sequence is executed when:■You turn on the power to your Tablet PC.■You restart your Tablet PC from the WindowsShut Down dialog box.■The software initiates a system restart. Example:When you install a new application.BIOS SETUP UTILITYThe BIOS Setup Utility is a program that sets up the operating environment for your Tablet PC. Your BIOSis set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your Tablet PC.The BIOS Setup Utility configures:■Device control feature parameters, such as changingI/O addresses and boot devices.■System Data Security feature parameters, suchas passwords.Entering the BIOS Setup UtilityTo enter the BIOS Setup Utility do the following: 1. Turn on or restart your Tablet PC.2. Press the [F2] key once the Fujitsu logo appearson the screen. This will open the main menuof the BIOS Setup Utility with the currentsettings displayed.3. Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings.BIOS GuideA guide to your Tablet PC’s BIOS is available online. Please visit our service and support Web site at www.fujitsupc.com. Once there, select Support, then select Tablet PCs under User’s Guides. Select LifeBook Tablet PC BIOS Guides from the pull-down menu for your Tablet PC series. If you are unsure of your Tablet PC’s BIOS number, refer to your packing slip.BOOTING THE SYSTEM We strongly recommend that you not attach any external devices until you have gone through the initial power-on sequence.When you turn on your LifeBook T Series Tablet PC for the first time, it will display a Fujitsu logo on the screen. When you turn on your Tablet PC be sure you have a power source. This means that a battery is installed and charged, or that the AC or Auto/Airline adapter is connected and has power.Never turn off your Tablet PC during the Power On Self Test (POST) or it will cause an error message to be displayed when you turn your Tablet PC on the next time. See “Power On Self Test Messages” on page 61If your data security settings require it, you may be asked for a password before the BIOS main menu will appear.T Series.book  Page 34  Thursday, July 31, 2003  10:49 AM
35Getting StartedIf you do nothing the system will load the operating system, and then the Windows Welcome will begin.Designed to accommodate the needs of many users, in many different countries, Windows needs to be config-ured the first time you use them. Windows has two parts: ■Getting Started: You have the opportunity to set up your modem so that your Tablet PC will be prepared to dial out. ■Windows License Agreement and Final Settings:You have the opportunity to review the Windows License Agreement.Getting StartedRead the instructions on the screens carefully and fill in the information as directed. You will be asked for such items as the language you wish to use, the country in which you live, your first and last name, and about how you dial out from where you will be using your Tablet PC. For the modem settings, enter your current location information where you will be using your Tablet PC. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button, and you will go directly to the condition of use page.Once you have set up your Tablet PC to dial out, Windows will make a free telephone call to test the settings. If the call is unsuccessful, you will be returned to the phone settings page where you may try to fix them. If you are unable to fix the settings please contact Fujitsu Service and Support. See “FPC Contact Informa-tion” on page 3 If you would simply like to move on, and register at a later time, you may click the Skip button, and you will go directly to the Condition of Use page.RegistrationIf your connection is successful, you will go to the Registration Confirmation page. On this page simply enter the requested information, and then check the box at the bottom to register your copy of Windows with Microsoft. Once you have finished, click the Next button to continue.Final SettingsThe first part of your final settings is the Windows End User License Agreement. Read the agreement carefully. When you finish reading you must accept or reject the terms of the agreement and then click on the Next button.ACTIVATING ADDITIONAL UTILITIESThe first time you boot up your system, you will see a Click Me! icon on the system desktop. When you double-click the Click Me! icon, your system will automatically add appropriate utilities based on your system’s configuration.The ClickMe! icon disappears after it has been run the first time.REGISTERING YOUR LIFEBOOK T SERIES TABLET PCWhat are the benefits of registering?You will receive an identification label for your Tablet PC, which, if your Tablet PC is ever lost, may help in getting it returned to you. You will also receive technical support access and useful product mailings. How do I register?To register your system, visit our Web site at: www.fujitsupc.com/support.You may click Cancel at any time within this process to shut down Windows. You may restart this process at any time in the future, but you must complete it in order to use your computer.■If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows or to shut down your Tablet PC.■You cannot use your Tablet PC until you have accepted the License Agreement. If you stop the process, your Tablet PC will return to the beginning of the Windows Welcome Process, even if you power down your system and start it up again.T Series.book  Page 35  Thursday, July 31, 2003  10:49 AM
36LifeBook T Series Tablet PC - Section ThreePower ManagementYour LifeBook T Series Tablet PC has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your oper-ating conditions, such as those for the display bright-ness. Internal power management for your Tablet PC may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.Besides the options available for conserving battery power, there are also some things that you can do to prevent your Tablet PC battery from running down as quickly. For example, you can create an appropriate power saving profile, put your Tablet PC into Standby mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings.Table 3-1.  System Power StatesSUSPEND/RESUME BUTTONWhen your Tablet PC is active, the Suspend/Resume button can be used to manually put your Tablet PC into Standby mode. Push the Suspend/Resume button when your Tablet PC is active, but not actively accessing anything, and immediately release the button. You will hear two short beeps and your system will enter Standby mode. (See figure 2-6 on page 12 for location).If your Tablet PC is suspended, pushing the Suspend/Resume button will return your Tablet PC to active operation. You can tell whether or not your system is in Standby mode by looking at the Power indicator. See “Power Indicator” on page 15. If the indicator is visible and not flashing, your Tablet PC is fully operational. If the indicator is both visible and flashing, your Tablet PC is in Standby mode. If the indicator is not visible at all, the power is off or your Tablet PC is in Hibernate mode (See Hibernate Mode)STANDBY MODEStandby mode in Windows saves the contents of your Tablet PC’s system memory during periods of inactivity by maintaining power to critical parts. This mode will turn off the CPU, the display, the hard drive, and all of the other internal components except those necessary to maintain system memory and allow for restarting. Your Tablet PC can be put in Standby mode by:■Pressing the Suspend/Resume button when your system is turned on.■Selecting Standby from the Windows Shut Down menu.■Timing out from lack of activity.■Allowing the battery to reach the Dead BatteryWarning condition.■Closing the system cover.Your Tablet PC’s system memory typically stores the file(s) on which you are working, open application(s) information, and any other data required to support the operation(s) in progress. When you resume operation Power Mode System Activity Events causing system to enter mode stateFully On Mode System is running. CPU, system bus, and all other interfaces operate at full speed.■From Standby mode: System operation resumed (Suspend/Resume button pressed, resume on modem ring, resume on time).■From Hibernation mode: Suspend/Resume button pressed.■From Off mode: Suspend/Resume button pressed.Standby Mode(Suspend-to-RAM)Resume system logic remains powered and RAM remains powered to maintain active data. All other devices are turned off.■Standby timeout occurs.■Suspend request issued by software or by pressing the Suspend/Resume button.■Low battery.Hibernation Mode(Suspend-to-Disk)Windows saves desktop state (including open files and documents) to hard disk. CPU stops. All other devices are turned off.■Suspend timeout occurs.■Clicking Start -> Shut Down -> Hibernate (It may be necessary to Enable Hibernate Support from Windows Power Options.)■Low battery conditionPower Off System is fully powered off except for logic components required for Suspend/Resume button and real-time clock operation.■System shutdown.■Low battery conditionT Series.book  Page 36  Thursday, July 31, 2003  10:49 AM
37Getting Startedfrom Standby mode, your Tablet PC will return to the point where it left off. To resume operation, you must use the Suspend/Resume button to resume operation, and there must be an adequate power source available, or your Tablet PC will not resume.HIBERNATE MODEThe Hibernate mode saves the contents of yourTablet PC’s system memory to the hard drive as a part of the Suspend/Resume mode. Your Tablet PC is pre-configured to perform this function. The Hibernate mode can also be configured through the system BIOS to run in other ways depending on what you need to accomplish. See “BIOS Setup Utility” on page 34.Using Hibernate ModeHibernate default setting is enabled for Windows XP. To   enable or disable the Hibernation feature follow these easy steps:1. From the Start menu, select Settings, and then select Control Panel -> Power Options.2. Select Hibernation, and then select the box to enable or disable this feature.To   use Hibernate mode with Windows XP systems:1. Click on the Start button, click Shut Down.2. Select Hibernate option from the “What do you want the computer to do” list.DISPLAY TIMEOUT The Video Timeout is one of the power management parameters. This feature saves power by turning off the display if there is no keyboard or pointer activity for the user selected timeout period. Any keyboard or pointer activity will cause the display to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows Power Management.HARD DISK TIMEOUTThe Hard Disk Timeout is another one of the power management parameters. This feature saves power by turning off the hard drive if there is no hard drive activity for the user selected timeout period. Any attempt to access the hard drive will cause it to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows.WINDOWS POWER MANAGEMENT The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Options to set the timeout values for turning off the display and hard disks whether you are running the Tablet PC on battery power or one of the adapters. RESTARTING THE SYSTEMIf your system is on and you need to restart it, be sure that you use the following procedure. 1. Click the Start button, and then click Shut Down.2. Select the Restart option from within the Windows Shut Down dialog box.3. Click OK. Your Tablet PC will shut down and reboot.If you are running your Tablet PC on battery power, be aware that the battery continues to discharge while your Tablet PC is in Standby mode, though not as fast as when fully operational. ■Standby or Hibernate modes should not be used with certain PC Cards. Check your PC Card documentation for more information.■Disabling the Suspend/Resume button prevents it from being used to put your Tablet PC in Standby or Hibernate mode. The resume function of the button cannot be disabled.■If your Tablet PC is actively accessing information when you enter Standby or Hibernate mode, changes to open files are not lost. The files are left open and memory is kept active during Standby mode or the memory is transferred to the hard drive during Hibernate mode.■When PC Cards or external devices are in use, Save-to-Disk mode cannot return to the exact state prior to suspension, because all peripheral devices will be re-initialized when the system restarts.■The main advantage of using Hibernate mode is that power is not required to maintain your data. This is very impor-tant if you will be leaving your Tablet PC in a suspended state for a prolonged period of time. The drawback of using Hibernate mode is that it lengthens the power down and power up sequences and resets peripheral devices.T Series.book  Page 37  Thursday, July 31, 2003  10:49 AM
38LifeBook T Series Tablet PC - Section ThreePOWER OFFBefore turning off the power by choosing Shut Down from the Windows Start menu, check that the Hard Drive, CD-ROM, PC Card and the Floppy Disk Drive Access indicators are all Off. (See Figure 2-9 on page 15) If you turn off the power while accessing a disk or PC Card there is a risk of data loss. To assure that your Tablet PC shuts down without error, use the Windows shut down procedure.Using the correct procedure to shut down from Windows, allows your Tablet PC to complete its opera-tions and turn off power in the proper sequence to avoid errors. The proper sequence is:1. Click the Start button, and then click Shut Down.2. Select the Shut Down option from within the Windows Shut Down dialog box.3. Click OK.If you are going to store your Tablet PC for a month or more see the Care and Maintenance section. Turning off your Tablet PC without exiting Windows or turning on your Tablet PC within 10 seconds of the Tablet PC being shut off may cause an error when you start the next time. T Series.book  Page 38  Thursday, July 31, 2003  10:49 AM
394User-Installable FeaturesT Series.book  Page 39  Thursday, July 31, 2003  10:49 AM
40LifeBook T Series Tablet PC - Section FourT Series.book  Page 40  Thursday, July 31, 2003  10:49 AM
41User-Installable FeaturesLithium ion BatteryYour LifeBook T Series Tablet PC has a Lithium ion battery that provides power for operating your Tablet PC when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemi-cals or other hazards.The Lithium ion battery operating time may become shorter if it is used under the following conditions:■When used at temperatures lower than 41° F (5° C) or higher than 95° F (35° C). Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range. See “Battery Charging Indicator” on page 16.■When using a high current device such as a modem, CD-ROM drive, or hard drive, using the AC adapter will conserve your battery life.RECHARGING THE BATTERYIf you want to know the condition of the Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes.The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your Tablet PC and connect the AC orAuto/Airline adapter.There is no memory effect on the Lithium ion battery, therefore you do not need to discharge the battery completely before recharging. The charge times will be longer if your Tablet PC is in use while the battery is charging. If you want to charge the battery more quickly, put your Tablet PC into Standby mode, or turn it off while the adapter is charging the battery. See “Power Management” on page 36.Low Battery StateWhen the battery is running low, your Tablet PC will beep every 15 seconds and the Battery Level indicator will flash. If you do not respond to the low battery alarm, the batteries will continue to discharge until they are too low to operate. When this happens there will be a multiple beep alarm and the Battery Level indicator will show a dead battery. Your Tablet PC will then go into Standby mode to try and protect your data for as long as possible. There is no guarantee that your data will not be lost once the Tablet PC reaches this point.■Do not leave a faulty battery in your Tablet PC. It may damage your AC adapter, optional Auto/Airline adapter, another battery or your Tablet PC itself. It may also prevent operation of your Tablet PC by draining all available cur-rent into the bad battery.■Under federal, state, or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this infor-mation elsewhere, contact your support representative at 1-800-8Fujitsu.Actual battery life will vary based on screen brightness, applications, features, power management settings, battery condition and other customer preferences.CD-ROM drive or hard drive usage may also have a significant impact on battery life. The battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one.Make sure that the Battery Charging indicator and the percentage charge is shown inside the Battery Level icon on the Status Indicator Panel.Using heavy current devices such as a modem or frequent CD-ROM and PCMCIA powered external device accesses may prevent charging completely.■You may not be able to hear the alarm if the volume control is set too low or is turned off by the hardware or software. However, you will be able to see the Battery Level indicator flash. Once the low battery alarm occurs you must save all your data and put your Tablet PC into Standby mode until you can provide a new power source. You should provide a charged battery or AC or Auto/Airline Adapter as soon as possible. ■When you are in Standby mode there must always be at least one power source active. If you remove all power sources while your Tablet PC is in Standby mode, any data that has not been saved to the hard drive will be lost.T Series.book  Page 41  Thursday, July 31, 2003  10:49 AM
42LifeBook T Series Tablet PC - Section FourDead Battery Suspend mode shows on the Status indi-cator just like the normal Standby mode. Once your Tablet PC goes into Dead Battery Suspend mode youwill be unable to resume operation until you providea source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your Tablet PC while an adapter is charging the battery.Shorted BatteriesThe Status Indicator panel uses a symbol inside the battery outline of the Battery Level indicator to display the operating level available in that battery. (See figure  on page 15) If this display shows a Shorted Battery, it means that the battery is damaged and must be replaced so it does not damage any other parts of your Tabl e t PC .REPLACING THE BATTERY Your LifeBook T Series Tablet PC comes with one battery pack; you might want to consider purchasing a spare. By keeping a spare battery fully charged, you can immediately swap with one that is not charged. There are two ways to swap batteries: cold-swapping and warm-swapping. Cold-swapping means swapping batteries when the system has been powered down; warm-swapping is performed when the system is in Standby mode. Cold-swapping batteriesTo cold-swap batteries in your battery compartment, follow these easy steps: (Figure 4-1)1. Have a charged battery ready to install.2. Shut down your notebook and disconnectthe AC adapter.3. Press the battery release latches to open the compartment.4. Remove the battery from the compartment.5. Slide the new battery into the compartment.6. Close the compartment and the battery release latches will click into place.7. Plug in the AC adapter and turn the power on. Figure 4-1.  Removing the BatteryWarm-swapping BatteriesTo warm-swap batteries in your battery compartment follow these easy steps: (Figure 4-1)1. Close any open files and put your Tablet PC into Standby mode.2. Press the battery release latches to open the compartment.3. Remove the battery from the compartment.4. Slide the new battery into the compartment.5. Close the compartment and the battery release latches will click into place.6. Press the Suspend/Resume button to return your Tablet PC to normal operation. You have only a few minutes to perform a warm-swapping before the internal bridge battery runs out of power. Have the charged battery nearby when performing a warm battery swap.If the Lithium ion battery connector is not fully seated, you may not be able to use your Tablet PC or charge your battery.Battery Release LatchesBattery CompartmentT Series.book  Page 42  Thursday, July 31, 2003  10:49 AM
43User-Installable FeaturesMemory UpgradeModuleYour Fujitsu LifeBook T Series Tablet PC comes with a minimum of 256 MB of high speed Double Data Rate Synchronous Dynamic RAM (DDR SDRAM), 266 MHz factory installed. To increase your system’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compati-bility, purchase the SDRAM module only from the Fujitsu web store at www.fujitsupc.com.INSTALLING MEMORY UPGRADE MODULES1. Turn off power to your LifeBook Tablet PC and remove any power adapter (AC or auto/airline).2. Make sure that all the connector covers are closed.3. Turn the Tablet PC bottom side up, and remove the screws of the memory upgrade module compart-ment. (Figure 4-2) 4. Remove the cover.Figure 4-2. Opening the Memory Upgrade Compartment5. Remove the memory upgrade module from the static guarded sleeve. As noted above, if you are installing a 1 GB memory module by itself or with a smaller module, it must be installed in slot 1.6. Align the memory upgrade module with the component side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. (Figure 4-3)7. Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is prop-erly in place. Figure 4-3. Installing a Second Memory Module8. Replace the cover. (Figure 4-4)9. Replace the screws.Figure 4-4. Replacing the Memory Compartment CoverTO REMOVE A MEMORY UPGRADE MODULE1. Perform steps 1 through 4 of Installing a Memory Upgrade Module.2. Pull the clips sideways away from each side of the memory upgrade module at the same time. 3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the rear of your notebook. (Figure 4-5)Figure 4-5. Removing a Memory Upgrade Module■If you are installing a 1 GB memory upgrade module by itself or with a smaller module, it must be installed in slot 1 (Figure 4-2).■Do not remove any screws from the memory upgrade module compart-ment except those specifically shown in the directions for installing and removing the module.Slot 1Slot 2The memory upgrade module is not something you routinely remove from your notebook. Once it is installed, you should leave it in place unless you want to change system memory capacity.T Series.book  Page 43  Thursday, July 31, 2003  10:49 AM
44LifeBook T Series Tablet PC - Section Four4. Store the memory upgrade module in a static guarded sleeve.5. Replace the cover. (Figure 4-4)6. Replace the screws.CHECKING THE MEMORY CAPACITYOnce you have changed the system memory capacity by either adding or removing a memory upgrade module, be sure to check that your notebook has recognized the change.You can check the memory capacity by clicking [Start]-> Control Panel, then double-clicking the System icon. Select the General tab and check the amount of memory under “Computer.”The amount of memory displayed should be approxi-mately the total of all memory modules installed. There may be a discrepancy of 8 MB which is allocated for fixed video memory.Your Tablet PC uses Dynamic Video Memory Technology (DVMT), which allows the video driver to dynamically determine the amount of memory that is used. Your Tablet PC can use a maximum of 64 MB of system memory for video functions. If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. (If the module is properly installed and the capacity is still not correctly recognized, see Troubleshooting on page 54.T Series.book  Page 44  Thursday, July 31, 2003  10:49 AM
45User-Installable FeaturesFigure 4-6. Installing/Removing PC CardsPC CardsYour LifeBook T Series Tablet PC supports Type I, II, and Type III PC Cards, which can perform a variety of functions. Some available PC Cards include:■Fax/data modem cards.■Local area network (LAN) cards.■IDE solid-state disk cards.■SCSI cards.■Other PC Cards that conform to PCMCIA 2.1 or CardBus standards.■Optional SmartCard adapterFor further information, refer to the instructions supplied with your PC Card.INSTALLING PC CARDSPC Cards are installed in the PC Card slot. To install aPC Card, follow these easy steps: (Figure 4-6) 1. See your PC Card manual for specific instructions on the installation of your card. Some PC Cardsmay require your Tablet PC to be Off whileinstalling them.2. Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards.3. Insert your PC Card into the slot, with the product label facing up. 4. Push the card into the slot firmly until it is seated in the opening.REMOVING PC CARDSTo remove a PC Card, follow these easy steps:1. See your PC Card manual for specific instructions on removing your card. Some PC Cards may require your Tablet PC to be in Standby Mode or Off while removing them.2. Push the Eject button until it pops out, and then push it in to eject the card. This will allow you to remove the card.SMART CARD READERAn embedded Smart Card Reader is provided on your Tablet PC. Smart Cards are the same size and shape as credit cards, but they contain an integrated micropro-cessor chip. The chip can hold a variety of information, and provides the user with many possible options, such as allowing them to make secure purchases, pay for phone calls, store security information, and provide identification and information. In order to use the embedded Smart Card Reader, you must purchase an optional Smart Card holder for instal-lation into an available Type II PC Card slot. Eject ButtonsPC Card SlotsPC Card■Installing or removing a PC Card during your Tablet PC’s shutdown or bootup process may damage the card and/or your Tablet PC.■Do not insert a PC Card into a slot if there is water or any other substance on the card as you may permanently dam-age the card, your Tablet PC, or both. If the dialog box states that the device can’t be removed, you must save all open files, close any open applications and shut down your Tablet PC. If the PC Card has an external connector and cable, do not pull the cable when removing the card.T Series.book  Page 45  Thursday, July 31, 2003  10:49 AM
46LifeBook T Series Tablet PC - Section FourFigure 4-7.  Port Replicator rear panelPort ReplicatorAn optional Port Replicator is available from Fujitsu to support your LifeBook T Series Tablet PC. The Port Replicator extends the functionality of your Tablet PC by providing ports to connect USB devices, an external monitor, or a LAN device. The Port Replicator connects to the bottom of your Tablet PC. See “Device Ports” on page 48.REAR PANEL COMPONENTSFollowing is a brief description of the optional Port Replicator’s rear panel components. External Monitor PortThe external monitor port allows you to connect an external VGA or SVGA monitor. Note that if a Port Replicator is attached, you must use the external monitor port on the Port Replicator. (Figure 4-7)LAN (RJ-45) JackThe LAN jack allows you to connect a LAN to the Port Replicator. Note that when the system is attached to the Port Replicator, the LAN Jack on the Port Replicator should be used, not the one on the system.DC Power JackThe DC power jack allows you to plug in the AC adapter to power your Tablet PC and charge the internal Lithium ion battery. USB 2.0 PortsThe two USB 2.0 ports allow you to connect USB devices such as game pads, pointing devices, and keyboards. USB 2.0 is downward-compatible with USB 1.1 devices, so older USB devices will work with these ports. USB 2.0 is a much faster design, running 40 times faster than USB 1.1.External Monitor PortLAN (RJ-45) JackDC Power JackUSB PortsT Series.book  Page 46  Thursday, July 31, 2003  10:49 AM
47User-Installable FeaturesFigure 4-8. Port Replicator front panel FRONT PANEL COMPONENTSFollowing is a brief description of the optional Port Replicator’s front panel componentsDocking PortThe docking port connects the Port Replicator to your Tabl e t PC . (Figure 4-8)Port Replicator Release LatchSlide the Port Replicator Release Latch sideways to remove the Port Replicator from your Tablet PC. (Figure 4-8)ATTACHING THE PORT REPLICATORTo attach the Port Replicator, align the Port Replicator connector on the bottom of your Tablet PC with the connector on the Port Replicator and push together at the two corners. (Figure 4-9)Figure 4-9.  Attaching the Port ReplicatorFigure 4-10.  Unlatching the Port ReplicatorDETACHING THE PORT REPLICATORTo detach the Port Replicator:1. Slide the Port Replicator release latch to release the Port Replicator from your Tablet PC. (Figure 4-10)2. Pull away the Port Replicator to detach it from your Tablet PC. (Figure 4-11)Figure 4-11.  Removing the Port ReplicatorDocking PortPort ReplicatorRelease LatchT Series.book  Page 47  Thursday, July 31, 2003  10:49 AM
48LifeBook T Series Tablet PC - Section FourDevice PortsYour LifeBook T Series Tablet PC and the optional Port Replicator come equipped with multiple Device Ports to which you can connect an external device including: disk drives, keyboards, modems, printers, etc. MODEM (RJ-11) JACKThe modem (RJ-11) jack is used for an internal modem. To connect the telephone cable follow these easy steps: (See Figure 2-6 on page 12 for location)1. Align the connector with the jack opening.2. Push the connector into the jack until it is seated.3. Plug the other end of the telephone cable into atelephone outlet.INTERNAL LAN (RJ-45) JACK The internal LAN (RJ-45) jack is used for an internalFast Ethernet (10/100 Base-T/Tx) connection. You will need to configure your Tablet PC to work with your particular network. (Please refer to your network administrator for information on your network configu-ration.) To connect the LAN cable follow these easy steps: (See Figure 2-7 on page 13 for location)1. Align the connector with the jack opening.2. Push the connector into the jack until it is seated.3. Plug the other end of the cable into a LAN outlet.DOCKING PORTThe docking port is used for the connection of your Tablet PC to an optional port replicator. In order to connect your Tablet PC to one of these devices follow the instructions that came with your docking port. (See Figure 2-8 on page 14 for location)UNIVERSAL SERIAL BUS PORTSThe two Universal Serial Bus 2.0 ports (USB) allow you to connect USB devices such as external floppy disk drives, external CD and DVD drives, game pads, pointing devices, keyboards and/or speakers. USB 2.0 is downward-compatible with USB 1.1 devices, so older USB devices will work with these ports. USB 2.0 is a much faster design, running forty times faster than USB 1.1.In order to connect a USB device, follow these easy steps: (See Figure 2-7 on page 13 for location)1. Align the connector with the port opening.2. Push the connector into the port until it is seated.INFRARED PORTThe Infrared IrDA 1.1 (4 Mbps) port allows for wireless data transfer between your Tablet PC and other IrDA-compatible devices, such as another computer or a printer, without the use of a cable. (See Figure 2-7 on page 13 for location)It is important to keep in mind that while carrying out this form of communication, both devices must be placed so their infrared ports are directly facing each other without obstruction. The devices must also be separated by at least 6" but no more than 36" for maximum performance. The following conditions may interfere with infrared communications:■A television, radio remote control unit, or a wireless headphone is being used nearby.■Direct sunlight, fluorescent light, or incandescent light shines directly on the port.The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook T Series Tablet PC. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.■The internal modem is designed to the ITU V.90 standard. Its maximum speed of 53000 bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600 bps at upload. ■The internal modem on all LifeBook T Series Tablet PC’s from Fujitsu PC Corporation are certified for use in the United States and Canada.■Depending upon the configuration of your system, your LifeBook Tablet PC may have either a LAN jack or an IEEE 1394 jack.Note that the optional Port Replicator is designed to cover the LAN jack located on the system. This design ensures that the LAN jack on the Port Replicator is the only one used when the Port Replicator is installed.T Series.book  Page 48  Thursday, July 31, 2003  10:49 AM
49User-Installable FeaturesMICROPHONE JACKThe microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8"(3.5 mm) mono mini-plug in order to fit into the microphone jack of your Tablet PC. In order to connect a microphone follow these easy steps: (See Figure 2-5 on page 11 for location)1. Align the connector with the port opening.2. Push the connector into the port until it is seated.HEADPHONE JACKThe headphone jack allows you to connect headphones or powered external speakers to your Tablet PC. Your headphones or speakers must be equipped with a 1/8" (3.5 mm) stereo mini-plug. In order to connect head-phones or speakers follow these easy steps: (See Figure 2-5 on page 11 for location)1. Align the connector with the port opening.2. Push the connector into the port until it is seated.EXTERNAL MONITOR PORTThe external monitor port allows you to connect an external monitor. In order to connect an external monitor follow these easy steps: (See Figure 2-7 on page 13 for location)1. Remove the cover from the port opening, if present.2. Align the connector with the port opening.3. Push the connector into the port until it is seated.4. Tighten the two hold-down screws, located oneach end of the connector. ■Do not move either device while com-munication is active as it may interrupt data transmission.■Be careful not to scratch the infrared port lens. Scratches, dirt, or other sur-face marks can degrade operation.If you plug headphones into the headphone jack, the built-in stereo speakers will be disabled.When an external monitor is plugged in, pressing the [Fn] + [F10] keys allows you to change your selection of where to send your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external monitor only, finally moving to both the built-in display panel and an external monitor.T Series.book  Page 49  Thursday, July 31, 2003  10:49 AM
50LifeBook T Series Tablet PC - Section FourT Series.book  Page 50  Thursday, July 31, 2003  10:49 AM
515TroubleshootingT Series.book  Page 51  Thursday, July 31, 2003  10:49 AM
52LifeBook T Series Tablet PC - Section FiveT Series.book  Page 52  Thursday, July 31, 2003  10:49 AM
53TroubleshootingTroubleshootingYour LifeBook T Series Tablet PC is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.IDENTIFYING THE PROBLEMIf you encounter a problem that you are having diffi-culty in solving, go through the following procedure before pursuing further troubleshooting:1. Tur n off your Tabl e t  PC.2. Make sure the AC adapter is plugged into your Tablet PC and to an active AC power source.3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.5. Turn on your Tablet PC. Make sure it has been off at least 10 seconds before you turn it on.6. Go through the boot sequence.7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information.8. If you still have the problem after taking all of the above approaches, please check our Web site at www.fujitsupc.com for possible known support issues. 8. If you have tried the solutions suggested in the Troubleshooting Table and checked our Web site for possible solutions without success, contact your support representative: Toll free: 1-800-8Fujitsu Fax: 1-901-259-5700 E-mail: 8fujitsu@fujitsupc.com Web site: http://www.fujitsupc.com.Before you place the call, you should have the following information ready so that the customer support repre-sentative can provide you with the fastest possible solu-tion:■Product name■Product configuration number■Product serial number■Purchase date■Conditions under which the problem occurred■Any error messages that have occurred■Hardware configuration■Type of device connected, if anySee the Configuration Label on the bottom of yourTablet PC for configuration and serial numbers. (See figure 2-8 on page 14 for location)SPECIFIC PROBLEMSUsing the Troubleshooting TableWhen you have problems with your Tablet PC, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you diffi-culty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your Tablet PC.■If you keep notes about what you have tried, your support representative may be able to help you more quickly by giv-ing additional suggestions over the phone.■Do not return a failed Tablet PC to your supplier until you have talked to a sup-port representative.T Series.book  Page 53  Thursday, July 31, 2003  10:49 AM
54LifeBook T Series Tablet PC - Section FiveTROUBLESHOOTING TABLEProblem PageAudio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 54Docking Problems . . . . . . . . . . . . . . . . . . . . . . . . page 54Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 54Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 54Pen Input Problems . . . . . . . . . . . . . . . . . . . . . . . page 55Infrared Problems  . . . . . . . . . . . . . . . . . . . . . . . . page 55Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 55Problem PageModem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 55USB Device Problems . . . . . . . . . . . . . . . . . . . . . page 56PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 56Power Failures  . . . . . . . . . . . . . . . . . . . . . . . . . . . page 56Shutdown and Startup Problems . . . . . . . . . . . . page 58Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 59Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 60Problem Possible Cause Possible SolutionsAudio ProblemsThere is no sound coming from the built-in speakers.The software volume control is set too low.Adjust the sound volume control settings in your software, operating system and applications.Headphones are plugged into your Tablet PC.Plugging in headphones disables the built-in speakers, remove the headphones.Software driver is not config-ured correctly.Refer to your application and operating system documentation for help.Sound could have been muted with function keys.Press [F3] while holding the [Fn] key to toggle the sound on and off.Port Replicator ProblemsTablet PC does not turn on when installed in optional Port ReplicatorPort Replicator AC adapter is not plugged in. Provide power to the Port Replicator.Tablet PC is not properly seated in the Port Replicator.Remove and re-dock your Tablet PC.Hard Drive ProblemsYou cannot access your hard drive.The setup utility is incorrectly set for your internal (Primary Master) hard drive.Revise BIOS settings to set the Primary Mastercorrectly. See “BIOS Setup Utility” on page 34.The wrong drive designator was used by an application when a bootable CD-ROM was used to start the Tablet PC.Verify drive designator used by application is inuse by the operating system. When the operating system is booted from a CD, drive designationsare automatically adjusted. Security is set so your oper-ating system cannot be started without a password.Verify your password and security settings.Keyboard or Mouse ProblemsThe built-in keyboard does not seem to work.The Tablet PC has gone into Standby mode.Push the Suspend/Resume button.Your application has locked out your keyboard.Try to use your integrated pointing device to restart your system. If this fails, turn your Tablet PC off by pressing the suspend/resume button for 10 seconds or more, and then turn it back on.T Series.book  Page 54  Thursday, July 31, 2003  10:49 AM
55TroubleshootingYou have installed an external keyboard or mouse, and it does not seem to work.Your external device is not properly installed.Re-install your device. See “Device Ports” on page 48.Your operating system soft-ware is not set up with the correct driver for that device.Check your device and operating system docu-mentation and activate the proper driver.You have connected an external keyboard or a mouse and it seems to be locking up the system.Your operating system soft-ware is not set up with the correct driver for that device.Check your device and operating systemdocumentation and activate the proper driver.Your system has crashed. Try to restart your Tablet PC. If that fails, turn off the power by pressing the suspend/resume button for at least 10 seconds, and then power back on. Pen Input ProblemsCursor is not tracking the penThe system may be uncalibratedIf the cursor on the screen appears to be misaligned with the pen or is not accurately tracking the pen, calibrate the pen. See “Calibrating the Pen” on page 27.Infrared ProblemsInfrared data transfer is not workingThe IrDA port on the system can’t “see” the IrDA port on the other device.Move the system so that there is a direct line-of-sight path between the two ports.The system and the other device are too far from each other.Move the system and the device so that they are three feet or less from each other.The viewing angle between the devices is too great.The viewing angle between the system port and the device port cannot be more than 15 degrees from a center line between the IrDA port on the Tablet PC and the IrDA port on the other device.You are using an old version of IrDA.The device with which you are trying to communi-cate must be compliant with IrDA standard 1.1.There are possibly problems in one or both devices. Go to Start -> (All) Programs -> Accessories -> Communications -> New Connection Wizard. Verify that "Set up an advanced connection" is checked and follow the on-screen instructions. Memory ProblemsYour Power On screen, or Info menu of the BIOS setup utility information, does not show the correct amount of installed memory.Your memory upgrade module is not properly installed.Turn off your Tablet PC. Remove and re-install your memory upgrade module. See “Memory Upgrade Module” on page 43.You have a memory failure. Check for Power On Self Test (POST) messages. See “Power On Self Test Messages” on page 61.Modem ProblemsMessages about modem operation.Messages about modem operation are generated by whichever modem application is in use.See your application software documentation for additional information.Problem Possible Cause Possible SolutionsT Series.book  Page 55  Thursday, July 31, 2003  10:49 AM
56LifeBook T Series Tablet PC - Section FiveModem does not appear to work.Modem may not have been intialized.Verify that the modem has been initialized by the operating system. TO do so, right-click on My Computer and select the Hardware tab. Click [Device Manager] and click on the "+" symbol that appears next to Modems. Verify that your device is listed as installed.USB Device ProblemsYou have installed a USB device, but your Tablet PC does not recognize the device, or the device does not seem to work properly.The device is not properly installed.Remove and re-install the device. See “Device Ports” on page 48.The device may have been installed while an application was running, so your Tablet PC is not aware of its installation.Close the application and restart your Tablet PC.Yo u r  s of tw are  m a y  n o t  h ave  the correct software driver active.See your software documentation and activate the correct driver.Your device and another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.PC Card ProblemsA card inserted in the PC Card slot does not work or is locking up the system.The card is not properly installed.Remove and re-install the card. See “PC Cards” on page 45.The card may have been installed while an application was running, so your Tablet PC is not aware of its installation.Close the application and restart your Tablet PC.Yo u r  s of tw are  m a y  n o t  h ave  the correct software driver active.See your software documentation and activate the correct driver.Your PC Card device and another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.Power FailuresYou turn on your Tablet PC and nothing seems to happen.The installed battery is completely discharged or there is no power adapter (AC or Auto/Airline) installed.Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 15. Install a charged battery or a Power adapter.The battery is installed but is faulty.Use the Status Indicator Panel to verify the presence and condition of the battery. See “Status Indicator Panel” on page 15. If a battery is indicating a short, remove that battery and operate from another power source or replace that battery.Problem Possible Cause Possible SolutionsT Series.book  Page 56  Thursday, July 31, 2003  10:49 AM
57TroubleshootingYou turn on your Tablet PC and nothing seems to happen.(continued)The battery is low. Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 15. Use a Power adapter until the battery is charged.The AC or auto/airline adapter is not plugged in properly.Verify that your adapter is connected correctly. See “Power Sources” on page 33.The Power adapter (AC or auto/airline) is faulty.Try a different Power adapter or install a charged optional second battery.The Power adapter (AC or auto/airline) has no power from the AC outlet, airplane seat jack, or the car’s cigarette lighter.Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.Your Tablet PC turns off all by itself.The power management parameters are set for auto timeouts which are too short for your operating needs.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings, or close your applicationsand go to the Power Savings menu of the setup utility to adjust the timeout values to better suityour operation needs.You are operating on battery power only and have ignored a low battery alarm until the battery is at the dead battery state and your machine has gone into Dead Battery Suspend mode.Install a power adapter and then push the Suspend/Resume button. See “Power Sources” on page 33.You have a battery failure. Verify the condition of the battery using theStatus Indicator panel, and replace or removeany battery that is shorted. See “Status Indicator Panel” on page 15.Your power adapter has failed or lost its power source.Make sure the adapter is plugged in and the outlet has power.Your Tablet PC will not work on battery alone.The battery is dead. Replace the battery with a charged one or install a Power adapter.No battery is installed. Install a charged battery.The battery is improperly installed.Verify that the battery is properly connected by re-installing them.Your battery is faulty. Verify the battery condition using the Status Indi-cator panel and replace or remove any battery that is shorted. See “Status Indicator Panel” on page 15.The battery seems to discharge too quickly.You are running an application that uses a great deal of power due to frequent hard drive or CD-ROM access, or use of a modem or LAN PC card.Use a power adapter for this application when at all possible.Problem Possible Cause Possible SolutionsT Series.book  Page 57  Thursday, July 31, 2003  10:49 AM
58LifeBook T Series Tablet PC - Section FiveThe battery seems to discharge too quickly.(continued)The power savings features may be disabled.Check the power management and/or setup utility settings in the Power Savings menu and adjust according to your operating needs.The brightness is turned all the way up.Turn down the brightness adjustment. The higher the brightness the more power your display uses.The battery is very old. Replace the battery.The battery has been exposed to high temperatures.Replace the battery.The battery is too hot or too cold. Restore the Tablet PC to normal operating tempera-ture. The Charging icon on the Status Indicator panel will flash when the battery is outside itsoperating range.The AC Adapter is defective. Replace with another AC Adapter to see if the problem persists. Replace any defective AC Adapters.Shutdown and Startup ProblemsThe Suspend/Resume button does not work.The Suspend/Resume button is disabled from the Advanced submenu of the Power menu of the setup utility. Enable the button from the setup utility.You did not hold the button in long enough.Hold the button longer. This may need to be a few seconds if your application is preventing the CPU from checking for button pushes.There may be a conflict with the application software.Close all applications and try the button again.The system powers up, and displays power-on informa-tion, but fails to load the operating system.The boot sequence settings of the setup utility are not compatible with your configuration.Set the operating source by pressing the [F2] key while the Fujitsu logo is on screen, entering the setup utility and adjusting the source settings from the Boot menu. See “BIOS Setup Utility” on page 34.You have a secured system requiring a password to load your operating system.Make sure you have the right password. Enter the setup utility and verify the Security settings and modify them as accordingly. See “BIOS Setup Utility” on page 34.An error message is displayed on the screen during the Tablet PC boot sequence.Power On Self Test (POST) has detected a problem.See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. See “Power On Self Test Messages” on page 61.Your system display won’t turn on when the system is turned on or when the system has resumed.The system may be password-protected.Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.Problem Possible Cause Possible SolutionsT Series.book  Page 58  Thursday, July 31, 2003  10:49 AM
59TroubleshootingYour Tablet PC appears to change setup parameters when you start it.BIOS setup changes were not saved when you made them and exited the BIOS setup utility returning it to previous settings.Make sure you select Save Changes And Exit when exiting the BIOS setup utility.The BIOS CMOS back-up battery has failed.Contact your support representative for repairs. This is not a user-serviceable part.Video ProblemsThe built-in display is blank when you turn on your Tablet PC.The angle of the display and the brightness settings are not adequate for your lighting conditions.Move the display and the brightness control until you have adequate visibility.The optional Port Replicator is attached, an external monitor is plugged in, and the Tablet PC is set for an external monitor only.Pressing [F10] while holding down the [Fn] key allows you to change your selection of where tosend your display video. Each time you press the combination of keys you will step to the nextchoice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.The power management timeouts may be set for very short intervals and you failed to notice the display come onand go off again.Press any button the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standy mode, Auto Suspend or Video Timeout)The Tablet PC turned on with a series of beeps and your built-in display is blank.Power On Self Test (POST)has detected a failure which does not allow the displayto operate. Contact your support representative.Your system display won’t turn on when the system is turned on or when the system has resumed.The system may be password-protected.Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.The display goes blank by itself after you have been using it.The Tablet PC has gone into Video Timeout, Standby Mode, or Hibernate Mode because you have not used it for a period of time.Press a button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. See “BIOS Setup Utility” on page 34.The power management time-outs may be set for very short intervals and you failed to notice the display come onand go off again.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout)The display does not close. A foreign object, such as a paper clip, is stuck between the display and the keyboard.Remove all foreign objects from the keyboard.Problem Possible Cause Possible SolutionsT Series.book  Page 59  Thursday, July 31, 2003  10:49 AM
60LifeBook T Series Tablet PC - Section FiveThe display has bright or dark spots.If the spots are very tiny and few in number, this is normal for a large LCD display.This is normal; do nothing.If the spots are numerous or large enough to interfere with your operation needs.The display needs technical diagnosis; contact your support representative.The application display uses only a portion of your screen and is surrounded by a dark frame.You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compres-sion is enabled.When compensation is disabled, a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution will result. You can fill the screen but have less resolution by changing your compensation setting. (See the Video Features submenu, located within the Advanced menu of the BIOS. See “BIOS Setup Utility” on page 34.You have connected an external monitor and it does not display any information.Your BIOS setup is not set to enable your external monitor.Try toggling the video destination by pressing [Fn] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. See “BIOS Setup Utility” on page 34.Your external monitor is not properly installed. Reinstall your device. See “External Monitor Port” on page 49.Your operating system soft-ware is not set up with the correct software driver forthat device. Check your device and operating systemdocumentation and activate the proper driver.You have connected an external monitor and it does not come on.Your external monitor may not be compatible with your Tablet PC.See your monitor documentation and theExternal Monitor Support portions of theSpecifications section. See “Specifications” on page 73.Miscellaneous ProblemsAn error message is displayed on the screen during the operation ofan application.Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.Problem Possible Cause Possible SolutionsT Series.book  Page 60  Thursday, July 31, 2003  10:49 AM
61TroubleshootingPOWER ON SELF TEST MESSAGESThe following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes successfully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)*Extended RAM Failed at offset: nnnn Extended memory not working or not configured prop-erly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is prop-erly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.nnnn Extended RAM Passed Where nnnn is the amount of memory in kilobytes successfully tested.*Failing Bits: nnnn The hex number nnnnThis is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4) The fixed disk is not working or not configured prop-erly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.*Invalid NVRAM media typeProblem with NVRAM access. In the unlikely case that you see this message you may have some display prob-lems. You can continue operating but should contact your support representative for more information.*Keyboard controller error The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.*Keyboard error Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able touse an external keyboard until then. Contact your support representative.*Keyboard error nn BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted and your system may have to be re-installed from your back up media.*Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays "????". This is apotentially data destroying failure. Contact yoursupport representative.*Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays "????". This is apotentially data destroying failure. Contact yoursupport representative.*Press <F1> to resume, <F2> to SETUP Displayed after any recoverable error message. Pressthe [F1] key to continue the boot process or the [F2]key to enter Setup and change any settings.*Previous boot incomplete – Default configuration used Previous Power On Self Test did not complete success-fully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power and contact your support representative.T Series.book  Page 61  Thursday, July 31, 2003  10:49 AM
62LifeBook T Series Tablet PC - Section Five*Real time clock error Real-time clock fails BIOS test. May require board repair. Contact your support representative.*Shadow RAM Failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corruption if you continue. Contact your support repre-sentative.nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested.*System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your Tablet PC.System BIOS shadowed System BIOS copied to shadow RAM.*System CMOS checksum bad – run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.*System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.nnnn System RAM PassedWhere nnnn is the amount of system memory inkilobytes successfully tested.*System timer error The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.Video BIOS shadowed Video BIOS successfully copied to shadow RAM.MODEM RESULT CODESThe operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are:■OK■NO CARRIER■NO DIALTONE■CONNECT 53000 (Connection complete at 53,000 bps.)■ERROR■FAX■RING (This means an incoming call.)■BUSY■NO ANSWERWhen using the internal modem with applications that are not factory installed refer to the application documentation.T Series.book  Page 62  Thursday, July 31, 2003  10:49 AM
63TroubleshootingRestoring Your Pre-installed SoftwareThe Drivers and Applications Restore (DAR) CD contains:■Sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your LifeBook note-book configuration for use as documented below.■A link to the Drive Image Special Edition (DISE) utility on your hard disk drive.■Read-me files that provide additional use information for items on this CD-ROM.DRIVE IMAGE SPECIAL EDITION (DISE)PowerQuest Drive Image Special Edition (DISE) provides a way to restore your computer if you experi-ence a hard disk crash or other system failure. Fujitsu has used DISE to create an image of everything installed on the computer at the time you purchased it. The image is saved on a separate partition on the hard disk. You can use DISE to restore the factory image and return your computer to the state in which it was shipped from Fujitsu.Although it is not necessary, you can use DISE to store additional image files you create. For example, if you install several applications and save data files on your hard disk, you can create a new image that includes them and then save that image file on the hard disk. Then, in the event of a hard disk failure, you can restore the image that includes the applications and data files you use.Creating a Backup ImageYou can create a system backup image of your C:\ drive at any time. The C:\ partition must be a FAT, FAT32, or NTFS partition, and it must be directly before the backup partition on your hard disk.There are two ways to implement the DISE utility: when booting up the system, or from the desktop. Creating a backup image when booting upBefore creating an image at boot-up, you must first change the boot-up priority in the BIOS so that the system will go to the media drive first, rather than trying to boot-up from the hard drive or an external floppy disk drive.To  c ha ng e  th e b oo t - u p p r i or i t y :1. Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.2. Using the arrow keys, go to the Boot menu.3. Arrow down to the Boot Device Priority submenu and press [Enter].4. Arrow down to the CD-ROM drive in the list, and press the space bar (or the + key) to move the CD-ROM drive to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.)5. Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.After you have changed the boot priority, you can create a backup image when you are booting up:1. Install the DAR CD in the drive prior to booting up. When bootup begins, a message appears informing you that if you proceed, you will be able to: ■Create a new backup of drive C■Restore a previous backup, or,■Restore the original factory image. Note that creating a new backup will overwrite any previous backups, and restoring a backup or factory image will overwrite all information on the hard drive, including saved files. ■In order to install applications and/or drivers from the DAR CD, you will need to connect an external CD drive to your system.■If the DAR CD is in the drive when you boot up the system, and the Boot Sequence is set in the BIOS to boot from the CD drive first (see “Creating a backup image when booting up” on page 63), a message will appear informing you that if you proceed, you will have a choice of: creating a new backup of drive C:, restor-ing a previous backup, or restoring the original factory image. Note that creating a new backup will overwrite any previous backups, and restoring a backup or factory image will overwrite all information on the hard drive, including saved files. If you wish to install drivers or applications only from the CD, remove the disk from the drive, reboot the system, and insert the CD after Windows has started.If you have access to the internet, visit the Fujitsu Support web site at www.fujitsupc.com to check for the most current information, drivers and hints on how to perform recovery and system updates.Using the DISE feature will reduce the amount of usable disk space on your hard disk drive.T Series.book  Page 63  Thursday, July 31, 2003  10:49 AM
64LifeBook T Series Tablet PC - Section Four2. After you click [Y]es. You will be presented with two options: [Create New Backup] and [Restore Backup].After you click [Create New Backup], follow the on-screen instructions. By selecting [Create New Backup], a new image will be written to your backup partition. This will overwrite any previously created image. Creating a backup image from the desktopTo create a backup image from the desktop, select Drive Image SE from the Program list. You will initially be prompted to create a backup diskette. It is not necessary to create the backup diskette, since the DAR CD performs the same function.1. At the Drive Image Special Edition main screen, click Options> Create New Backup. DISE displays a warning that it must go to DOS to create the image.2. Click Ye s .DISE creates an image file in the backup partition. If you created a backup image previously, the new image overwrites the old one.Enlarging the Backup PartitionIf there is not enough unused space in the backup parti-tion on your hard disk, DISE will resize the partition. DISE will display the minimum, maximum, and recom-mended sizes for the backup partition. You choose the size you want.DISE takes the space from the FAT, FAT32, or NTFS partition that you are backing up. If there is not enough unused space in that partition to take, you will not be able to resize the backup partition and create an image file. You can delete files from the FAT, FAT32, or NTFS partition to create more unused space on the hard disk.Restoring a Backup ImageYou can restore either a factory image or a backup image you created. Be aware that restoring a backup image will replace the contents of the C:\ partition with the image you restore.1. Disable virus protection software. If virus protection software is enabled, DISE will lock up.2. From the DISE main window, click Options > Restore Backup to restore an image you created, or click Options > Restore Factory Backup to restore the factory image.DISE shuts down to DOS and restores the image file.Re-Installing Individual Drivers and Applications The Drivers and Application CD can be used to selec-tively re-install drivers and/or applications that may have been un-installed or corrupted. To re-install drivers and/or applications:1. Boot up the system and insert the DAR CD after Windows has started. A Fujitsu Welcome screen is displayed after the CD is inserted.2. From the left frame of the Welcome screen, “System Components” and “3rd Party Applications” can be selected. System Components are those drivers and utilities that have been developed by Fujitsu; 3rd Party Applications are applications developed by other vendors.Installing System Components1. To install system components, click on “System Components” in the left frame of the Welcome screen. A list of utilities and drivers will be displayed. Select one or more items from the list, or click [Select All] to select all items in the list. (To de-select your choices, click the [Clear All] button.2. Click [Install Selected Subsystems] to install the selected items.Installing 3rd Party Applications1. To install 3rd party applications, click on “3rd Party Applications” in the left frame of the Welcome screen. A list of applications will be displayed. 2. Select one of the items from the list, and follow the instructions that appear on the screen. Note that only one application may be installed at a time.3. Repeat step 2 to install additional applications.T Series.book  Page 64  Thursday, July 31, 2003  10:49 AM
656Care and MaintenanceT Series.book  Page 65  Thursday, July 31, 2003  10:49 AM
66LifeBook T Series Tablet PC - Section SixT Series.book  Page 66  Thursday, July 31, 2003  10:49 AM
67Care and MaintenanceCare and MaintenanceIf you use your LifeBook T Series Tablet PC carefully, you will increase its life and reliability. This section provides some tips for looking after the Tablet PC and its devices.LIFEBOOK T SERIES TABLET PCCaring for your Tablet PC■Your Tablet PC is a durable but sensitive electronic device. Treat it with care.■Make a habit of transporting it in a suitablecarrying case.■Do not attempt to service the computer yourself. Any unauthorized service performed on the computer will void the warranty.■ Always follow installation instructions closely.■Keep it away from food and beverages.■If you accidentally spill liquid on your Tablet PC:1. Turn it off.2. Position it so that the liquid can run out.3. Let it dry out for 24 hours, or longer if needed.4. If your Tablet PC will not boot after it has dried out, call your support representative.■Do not use your Tablet PC in a wet environment (near a bathtub, swimming pool).■Always use the AC adapter and batteries that are approved for your Tablet PC.■Avoid exposure to sand, dust and otherenvironmental hazards.■Do not expose your Tablet PC to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your Tablet PC.■Keep the covers closed on the connectors and slots when they are not in use.■Do not put heavy or sharp objects on the computer.■If you are carrying your Tablet PC in a briefcase, or any other carrying case, make sure that there are no objects in the case pressing on the lid.■Do not drop your Tablet PC.■Do not touch the screen with any sharp objects. Cleaning your Tablet PC■Always disconnect the power plug. (Pull the plug,not the cord.)■Clean your Tablet PC with a damp, lint-free cloth. Do not use abrasives or solvents.■Use a soft cloth to remove dust from the screen.Never use glass cleaners.Storing your Tablet PC■If storing your Tablet PC for a month or longer, turn the Tablet PC off, fully charge the battery, then remove and store all Lithium ion batteries.■Store your Tablet PC and batteries separately. If you store your Tablet PC with a battery installed, the bat-tery will discharge, and battery life will be reduced. In addition, a faulty battery might damage the Tablet PC.■Store your Tablet PC in a cool, dry location. Temperatures should remain between 13º F (-25º C) and 140º F (60º C).Traveling with your Tablet PC■Do not transport your Tablet PC while it is turned on. ■Do not check your Tablet PC as baggage. Carry it with you.■When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine. ■Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which adapter you'll need or ask your travel agent.Figure 6-1. Electrical equipment may be hazardous if misused. Operations of this product or similar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.Outlet Type LocationUnited States, Canada, Mexico, parts of Latin America, Japan, Korea, the Philippines, TaiwanRussia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South AsiaUnited Kingdom, Ireland, Malaysia, Singapore, parts of AfricaChina, Australia, New ZealandT Series.book  Page 67  Thursday, July 31, 2003  10:49 AM
68LifeBook T Series Tablet PC - Section SIxKEYBOARDCaring for your KeyboardThe keyboard of your computer is a very sensitive instrument. It is made up of many switches that are activated when you press on the keys. The keyboard is a major component of the heat dissipation system in a Tablet PC. Due to heat and size considerations the keyboard is not sealed. Because the keys are so close together, it is not easy for the user to see when liquids have fallen onto the circuitry below the keys. Attempting to clean the keyboard with a spray on cleaner or rag soaked with cleaner the liquid can drip onto the circuitry sight unseen. Once the liquid seeps between the layers of circuitry, it can cause corrosion or other damage to the circuits. This can result in keys which no longer operate, or which, when pressed, record the wrong characters and other similar failures.There is no repair for this problem other than replace-ment. The solution is to become aware of the issue and take appropriate steps to protect your keyboard. To clean the keyboard, use a rag dampened slightly with cleaning solution. Use extreme care to prevent liquid from dripping between the keys. Spraying directly on the keys should be avoided. The spray should be applied first to the cloth, and then the cloth wiped over the keys.BATTERIESCaring for your Batteries■Always handle batteries carefully.■Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.■Do not drop, puncture, disassemble, mutilate or incin-erate the battery.■Recharge batteries only as described in this manual and only in ventilated areas.■Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.■Do not leave a battery in storage for longer than 6 months without recharging it.Increasing Battery Life■Keep brightness to the lowest comfortable level.■Set the power management for maximum battery life.■Put your Tablet PC in Standby mode when it is turned on and you are not actually using it.■Limit your CD-ROM access.■Disable the Windows CD auto insert function.■Always use fully charged batteries.■Eject PCMCIA cards when not in use.OPTIONAL FLOPPY DISK DRIVE AND FLOPPY DISKSCaring for your Floppy Disks■Avoid using the floppy disks in damp anddusty locations.■Never store a floppy disk near a magnet or magnetic field.■Do not use a pencil or an eraser on a disk or disk label.■Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10º C) and 125º F (52º C).■Do not touch the exposed part of the diskbehind the metal shutter.Caring for your optional Optional Floppy Disk Drive■To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.■Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe tem-perature changes. Store at temperatures between 50º F (10º C) and 125º F (52º C).■Keep the floppy disk drive out of direct sunlight and away from heating equipment.■Avoid storing the floppy disk drive in locations subject to shock and vibration.■Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy diskdrive or disk.■Never disassemble or dismantle your floppy disk drive.OPTIONAL CD DRIVE AND CDsCaring for your CDsCDs are precision devices and will function reliably if given reasonable care.■Always store your CDs in its case when it is not in use.■Always handle CDs by the edges and avoid touching the surface.■Avoid storing any CDs in extreme temperatures.■Do not bend CDs or set heavy objects on them.■Do not spill liquids on CDs.■Do not scratch CDs.■Do not put a label on CDs.■Do not get dust on CDs.■Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.■If a CD is subjected to a sudden change in tempera-ture, cold to warm condensation may form on the sur- T Series.book  Page 68  Thursday, July 31, 2003  10:49 AM
69Care and Maintenanceface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry CDs.■If a CD is dirty, use only a CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.Caring for your Optional CD-ROM DriveYour CD-ROM drive is durable but youmust treat it with care. Please pay attention to the following points:■The drive rotates the compact disk at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.■Avoid using or storing the drive where it will be exposed to extreme temperatures.■Avoid using or storing the drive where it is damp or dusty.■Use of a commercially-available lens cleaner kit is recommended to maintain the drive lens. ■Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.■Avoid using or storing the drive where it will be subjected to shock or vibration.■Do not disassemble or dismantle the CD-ROM drive.PC CARDSCaring for your PC Card Slots PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Cards provides specific information for caring for the cards. When you don’t have a PC Card installed in your system, you should be sure to install the PC Card slot inserts that came with your system. These will help to keep dust and dirt out of your system.T Series.book  Page 69  Thursday, July 31, 2003  10:49 AM
70LifeBook T Series Tablet PC - Section SIxT Series.book  Page 70  Thursday, July 31, 2003  10:49 AM
717SpecificationsT Series.book  Page 71  Thursday, July 31, 2003  10:49 AM
72LifeBook T Series Tablet PC - Section SevenT Series.book  Page 72  Thursday, July 31, 2003  10:49 AM
73SpecificationsSpecificationsThis section provides the hardware and environmental specifications for your LifeBook T Series Tablet PC. Specifications of particular configurations will vary.CONFIGURATION LABELYour LifeBook T Series Tablet PC has a configuration label located on the bottom. (See figure 2-8 on page 14 for location). This label contains specific information regarding the options you’ve chosen for your Tablet PC. Following is an example label and information on how to read your own configuration label.Figure 7-1. Configuration LabelLifeBook T Series Tablet PC SpecificationsThe specifications for your particular model may vary. To determine the specifications for your system, please visit our Web site at: www.fujitsupc.com.Physical SpecificationsDimensions 11.5” w x 9.3” d x 1.1 / 1.4 (293 mm x 236 mm x 27.4 / 36.4 mm)Processing SpecificationsCPU/Speed Intel® Pentium® M processor 1.4 GHz @ 1.48V Chip set Intel 855GM - 400 MHzMemory/Storage SpecificationsMain RAM • 256 MB SDRAM (DDR 266 MHz)• 144-pin SO DIMM slots x 2256 MB, 512 MB, and 1.0 GB modules available, with a system maximum of 2.0 GB.L1 cache (CPU)64 KB on-die L2 cache 1 MB on-die T3010, PM 1.4G, 12.1 XGA, XPTE, 40G, 256MConfiguration P/N: ATEXXXXXXXXXXXXFPC P/N: FPCXXXXXXModelProcessorScreenSizeOperatingSystemHard Drive MemoryPart Number Configuration IDBIOS ROM 1 MB (Boot Block Type Flash ROM)Hard disk drive• 2.5” HDD• Minimum 40 GB IDE HDD• ATA 100• Shock-mounted• SMART SupportDisplay SpecificationsDisplay • Color LCD• Active Digitizer• 32-bit color• 12.1” TFT XGA (1024 x 768), 16M colors External monitor support: VGA (1600 x 1200 maximum) • Brightness: 8 levels• Viewing Angle:    Horizontal: 30 degrees (min.)     Vertical: 10 degrees (min.)VRAM Intel 855MG chipset with 8 MB shared memory using Dynamic Video Memory Technology (DVMT) delivers low-power, high-performance 3D/2D graphics, video, and display capabilities. Dynamic Video Memory Technology (DVMT) dynamically responds to application requirements and efficiently allocates the proper amount of memory (maximum is 64 MB) for optimal graphics and system performance. Interface SpecificationsIntegrated Interfaces• Modem (RJ-11)LAN (RJ-45)• USB 2.0 x 2•DC-In•IrDA• 15-pin D-SUB connector for external VGA monitor• Docking connectorInterfaceson Optional Port Replicator • DC Power• Pass-through LAN Port• External Monitor• USB 2.0 x 2• Docking PortPC Card Slots• Two Type I/Type II or one Type III• PCMCIA CardBus version 3.0LifeBook T Series Tablet PC Specifications (Continued)T Series.book  Page 73  Thursday, July 31, 2003  10:49 AM
74LifeBook T Series Tablet PC - Section SevenInfrared • System IR Port• IrDA version 1.1 (FIR, 4 Mbps)User Interface support• Keyboard Pitch: 19 mm, Stroke: 3 mm• TouchPad pointing device with scroll button• Active digitizer with pen input• On-screen keyboardAudio • RealTek ALC202 with 18-bit stereo audio, full duplex• Internal mono microphone and speaker• Mono microphone and stereo headphone jacksUser Controls• Programmable Application Buttons, each with primary and secondary functions (default applications: Microsoft Journal and Calculator)• Security button support• Suspend/Resume buttonStatus Indicators (LCDs)• Power• Charge/DC-In• Battery level• HDD• PC Card•Caps Lock•Num Lock• Scroll Lock• SecurityPower SpecificationsMain Battery • 6-cell • Removable, Lithium ion• 10.8 V @3600 mAh, 38.9 Wh• Warm-swappable•Recharge Time: Approximately 3.2 hours • Suspend Life: Minimum 3 daysOff State: Approximately 20 daysBridge Battery• 6-cell NiMH, 35 mAh• Life (with Suspend-to-RAM on bridge battery only): 5 minutes from full chargeAC Adapter Autosensing 100 - 240V, supplying 16 VDC, with a current of 3.75 ALifeBook T Series Tablet PC Specifications (Continued)Environmental SpecificationsTemperature Operating: 41o to 95o F (5o to 35o C) Non-operating: 5o to 140o F (-15o to 60o C) Humidity Operating: 20 to 85% non-condensingNon-operating: 8 to 85% non-condensingAgency Approval SpecificationsEmissions• EN55022 (CISPR22) Class B • FCC 15, Class B• FCC 15C, 15.247• ETSI EN 300-328• ICES-003• Canada RSS-210Immunity• EN55024 (1998)• ETSI EN 301-489-17 V.1.1.1 (2000-9)Safety • UL and cUL Listed, UL 60950• TuV T-Mark, EN60950Tele com • FCC Part 68• IC CS-03Additional SpecificationsOperating systems •Microsoft Windows XP Tablet PC EditionLifeBook T Series Tablet PC Specifications (Continued) T Series.book  Page 74  Thursday, July 31, 2003  10:49 AM
75Regulatory InformationRegulatory InformationFCC NOTICESNotice to Users of Radios and TelevisionThese limits are designed to provide reasonable protec-tion against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic-ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:nReorient or relocate the receiving antenna.nIncrease the separation between the equipment and receiver.nConnect the equipment into an outlet that is on a different circuit than the receiver.nConsult the dealer or an experienced radio/TVtechnician for help.Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Notice to Users of the US Telephone NetworkThis equipment contains an internal modem (Fujitsu Media Devices, MBH 7MD33) that complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.This equipment is designed to be connected to the tele-phone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.The ringer equivalent number (REN) of this equipment is 0.0B as shown on the label. The REN is used to deter-mine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local tele-phone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facili-ties, equipment, operations or procedures that could effect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to main-tain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu PC Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commis-sion or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equip-ment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such busi-ness, other entity, or individual.Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipmentT Series.book  Page 75  Thursday, July 31, 2003  10:49 AM
76LifeBook T Series Tablet PC - Section SevenDOC (INDUSTRY CANADA) NOTICESNotice to Users of Radios and TelevisionThis Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.Notice to Users of the Canadian Telephone Network NOTICE: This equipment (Fujitsu Media Devices modem, MBH 7MD33) meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number (4061A-8687) signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certifica-tion standards does not prevent service degradation in some situations.Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecom-munication company cause to request the user to disconnect the equipment from the telephone line.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equiva-lence Numbers of all the devices does not exceed five.Avis Aux Utilisateurs Du Réseau Téléphonique CanadienAVIS: Le présent matériel est conforme aux spécifica-tions techniques d’Industrie Canada applicables au matériel terminal. Cette conformité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement (4061A-8687), signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifica-tions techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel. Avant de connecter cet équipement à une ligne télépho-nique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécom-munications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur décon-necte l’équipement de la ligne téléphonique.AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.0. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équiva-lence de la sonnerie de tous les dispositifs n’excède pas 5.For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appro-priate electric inspection authority or elec-trician. This may be particularly important in rural areas.Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du ser-vice d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont con-nectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connex-ions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales.T Series.book  Page 76  Thursday, July 31, 2003  10:49 AM
77Regulatory InformationUL Notice This unit requires an AC adapter to operate. Use only UL Listed Class 2 Adapters with an output rating of 16 Vdc, with a current of 3.75 A.AC Adapter output polarity:For Authorized Repair Technicians OnlyThe modem-to-telephone network connection must be a line cord using a minimum #26 AWG wire.nFor continued protection against risk of fire, replace only with the same type and rating fuse.nDanger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dis-pose of used batteries according to the manufacturer’s instruction.+T Series.book  Page 77  Thursday, July 31, 2003  10:49 AM
78LifeBook T Series Tablet PC - Section SevenT Series.book  Page 78  Thursday, July 31, 2003  10:49 AM
798GlossaryT Series.book  Page 79  Thursday, July 31, 2003  10:49 AM
80LifeBook T Series Tablet PC - Section EightT Series.book  Page 80  Thursday, July 31, 2003  10:49 AM
81GlossaryGlossaryAC AdapterA device which converts the AC voltage from a wall outlet to the DC voltage needed to power your Tablet PC.ACPIAdvanced Configuration and Power InterfaceActive-Matrix DisplayA type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.AdHocA designation for wireless LAN network configuration. It indicates a form of communication limited to those personal computers which have wireless LAN function. For details, refer to "Ad hoc connection" on page 90.ADSLAsymmetric Digital Subscriber LineTechnology for transporting high bit-rate services over ordinary phone lines.Auto/Airline AdapterA device which converts the DC voltage from an auto-mobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your Tablet PC.BIOSBasic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your Tablet PC when you turn it on until it loads your installed operating system from disk. Infor-mation from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.BitAn abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).bpsAn abbreviation for bits per second. Used to describe data transfer rates.BootTo start-up a computer and load its operating system from disk, ROM or other storage media into RAM.BusAn electrical circuit which passes data between the CPU and the sub-assemblies inside your Tablet PC.Byte8 bits of parallel binary information.Cache MemoryA block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.CardBusA faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.CD-ROMCompact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.ChannelThe frequency band of wireless LAN to be used in communications over wireless LAN or at the access point.CMOS RAMComplementary metal oxide semiconductor random access memory. This is a technology for manufacturing random access memory which requires very low levels of power to operate.CommandAn instruction which you give your operating system. Example: run a particular application or format a floppy disk.ConfigurationThe combination of hardware and software that makes up your system and how it is allocated for use.CRTCathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam.DataThe information a system stores and processes.DCDirect current. A voltage or current that does not fluctuate periodically with time.Default ValueA pre programmed value to be used if you fail to set your own.T Series.book  Page 81  Thursday, July 31, 2003  10:49 AM
82LifeBook T Series Tablet PC - Section EightDHCP Dynamic Host Configuration ProtocolA protocol used for automatically fetching communica-tion parameters such as IP addresses. The side which assigns IP address is called DHCP server and the side that is assigned it is called DHCP client.DIMMDual-in-line memory module.DISEDrive Image Special Edition.A utility that allows you to restore the original factory image on your hard drive in the event of corruption or accidental erasure of files or applications.DiskA spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.Disk DriveThe hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.DisketteA floppy disk in a hard housing with a shutter.DMADirect Memory AccessSpecial circuitry for memory to memory transfers of data which do not require CPU action.DMIDesktop Management Interface A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals.DNS Domain Name SystemA function that controls the correspondence of IP addresses assigned to a computer with the name. Even for those computers whose IP addresses are unknown, if their names are known, it is possible to communicate with them.DOSDisk Operating System (MS-DOS is a Microsoft Disk Operating System).DriverA computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.ECPExtended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices.Encryption Key (Network Key)Key information used to encode data for data transfer.This device uses the same encryption key to encode and decode the data, and the identical encryption key is required between the sender and receiver.ESDElectro-Static Discharge. The sudden discharge of elec-tricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.Extended MemoryAll memory more than the 640KB recognized by MS-DOS as system memory.FCCFederal Communication Commission.Floppy DiskA spinning platter of magnetic data storage media which is highly flexible.GBGigabyte.Hard driveA spinning platter of magnetic data storage media where the platter is very stiff.I/OInput/Output. Data entering and leaving your Tablet PC in electronic form.I/O PortThe connector and associated control circuits for data entering and leaving your Tablet PC in electronic form.IDEIntelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.T Series.book  Page 82  Thursday, July 31, 2003  10:49 AM
83GlossaryIEEE 1394Industry standard that allows you to connect between your Tablet PC and a peripheral device such as a digital camera. Also known as "Firewire" or "iLINK".IEEE802.11aOne of the wireless LAN standards prescribed by the 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Elec-tronic Engineers). This standard allows communica-tions at the maximum speed of 54 Mbps by using a 5 GHz band which can freely be used without radio communication license. IEEE802.11bOne of the wireless LAN standards prescribed by 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Elec-tronic Engineers). It allows communications at the maximum speed of 11 Mbps by a band of 2.4 GHz (ISM band) which can freely be used without radio communi-cation license. IEEE802.11gOne of the wireless LAN standards prescribed by 802 committee in charge of establishing standards of LAN technology in IEEE (Institute of Electrical and Elec-tronic Engineers). It allows communications at the maximum speed of 54 Mbps by a band of 2.4 GHz (ISM band) which can freely be used without radio communi-cation license. InfraredLight just beyond the red portion of the visible light spectrum which is invisible to humans.InfrastructureA designation of Wireless LAN network configurations. It indicates a form of communication using an Access Point. For details, refer to "Infrastructure connection" on page 90.IP AddressAn address used for computers to communicate in the TCP/IP environment.Current IPv4 (version 4) uses four values in the range between 1 and 255. (Example: 192.168.100.123).There are two types of IP address: global address and private address.The global address is an only address in the world. It is controlled by JPNIC (Japan Network Information Center). A private address is an only address in the closed network.IRAn abbreviation for infrared.IrDAInfrared Data Association. An organization which produces standards for communication using infrared as the carrier.IRQInterrupt RequestAn acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.KB Kilobyte.LANLocal Area NetworkAn interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.LCDLiquid Crystal DisplayA type of display which makes images by controlling the orientation of crystals in a crystalline liquid.Lithium ion BatteryA type of rechargeable battery which has a high power-time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.LPT PortLine Printer Port. A way of referring to parallel interface ports because historically line printers were the first and latter the most common device connected to parallel ports.MAC Address Media Access Control AddressA unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards. For Ethernet, frames are sent and received based on this address.MBMegabyte.Megahertz1,000,000 cycles per second.T Series.book  Page 83  Thursday, July 31, 2003  10:49 AM
84LifeBook T Series Tablet PC - Section EightMemoryA repository for data and applications which is readily accessible to your Tablet PC’s CPU.MHzMegahertz.MIDIMusical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers.ModemA contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.MonauralA system using one channel to process sound from all sources.MPU-401A standard for MIDI interfaces and connectors.MTUMaximum Transmission UnitThe maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large.Network authenticationThe method of authentication performed by wireless LAN clients to connect with the access point. There are two types: open system authentication and shared key authentication. The type of authentication must be set to each client and also coincide with the setting of access point with which to communicate. Network authentica-tion is sometimes called authentication mode.Network keyData that is used for encrypting data in data communi-cation. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.Network name (SSID: Security Set Identifier)When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with "Network name (SSID)". In order to improve security, the network key is set allowing no communication unless "Network name (SSID)" coincides with the network key.NTSCNational TV Standards Commission. The standard for TV broadcast and reception for the USA.Open system authenticationOne of network authentication types for wireless LAN. Since there is no check of network key upon authentica-tion, clients can connect to the access point without submitting correct network keys. However, in case of actual communications, the same network key must be set. Open system authentication is sometimes called Open key authentication.Operating SystemA group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of micro-processor in order to produce the desired results from that particular equipment.PartitionA block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.PCIPeripheral Component Interconnect Self-configuring PC local bus. Designed by Intel, PCI has gained wide acceptance as a standard bus design.PCMCIAPCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.Peripheral DeviceA piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.Pitch (keyboard)The distance between the centers of the letter keys of a keyboard.PixelThe smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.POSTPower On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your Tablet PC. Status and error messages may be displayed T Series.book  Page 84  Thursday, July 31, 2003  10:49 AM
85Glossarybefore the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded. PPPoEPoint to Point Protocol over Ethernet.A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line.ProgramAn integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.ProtocolProcedures and rules use to send and receive data between computers.- Method of sending and receiving data- Process used to handle communication errorsConditions required for communication are organized in procedures for correct transfer of information.RAMRandom Access Memory. A hardware component of your Tablet PC that holds binary information (both program and data) as long as it has the proper power applied to it.RAM ModuleA printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.ResetThe act of reloading the operating system. A reset erases all information stored in RAM.RestartSee Reset.ResumeTo proceed after interruption. In your Tablet PC this refers to returning to active operation after having been in one of the suspension states.ROMRead Only Memory. A form of memory in which infor-mation is stored by physically altering the material. Data stored in this way can not be changed by your Tablet PC and does not require power to maintain it.SDRAMSynchronous Dynamic Random Access Memory.Serial PortA connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.Shared key authenticationOne of the network authentication types for wireless LAN. Upon authentication, the access point checks whether the same network key is set to the client. If the client uses a wrong network key or the network key itself is not set, authentication is unsuccessful, allowing no communications with the access point.SMARTSelf-Monitoring, Analysis and Reporting Technology (SMART) is an emerging technology that provides near-term failure predictions for hard drives. When SMART is enabled the hard drive monitors pre-determined drive attributes that are susceptible to degradation over time. If a failure is likely to occur, SMART makes a status report available so that the Tablet PC can prompt the user to back up the data on the drive. Naturally not all failures are predictable. SMART predictability is limited to those attributes which the drive can self-monitor. In those cases where SMART can give advance warning, a considerable amount of precious data can be saved.SRAMStatic random access memory. A specific technology of making RAM which does not require periodic data refreshing.SSIDService Set IdentifierSpecifies which network you are joining. Some systems allow you to specify any SSID as an option so you can join any network.StandbyTo make inoperative for a period of time. Your Tablet PC uses various suspension states to reduce power consumption and prolong the charge of your battery.Status IndicatorA display which reports the condition of some portion of your hardware. On your Tablet PC this is an LCD screen just above the keyboard.Stereo (audio)A system using two channels to process sound from two different sources.Subnet maskTCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. T Series.book  Page 85  Thursday, July 31, 2003  10:49 AM
86LifeBook T Series Tablet PC - Section EightSubnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.SVGASuper VGA.S-VideoSuper Video. A component video system for driving a TV or computer monitor.System ClockAn oscillator of fixed precise frequency which synchro-nizes the operation of the system and is counted to provide time of day and date.TCP/IP Transmission Control Protocol/Internet Protocol.A standard Internet protocol that is most widely used.TFTThin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.ULUnderwriters Laboratories – An independent organiza-tion that tests and certifies the electrical safety of devices.USBUniversal Serial Bus.Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer.VGAVideo Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of personal computers.VRAMVideo Random Access Memory. A memory dedicated to video display data and control.WFMWired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.Wi-Fi CompatibleWi-Fi (Wireless Fidelity) Identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guar-antees the interoperability of wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA website at: www.wirelessethernet.com.WLANWireless Local Area Network. A wireless interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.Write ProtectPrevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or direc-tory of floppy diskette or hard drive.XGAExtended VGA.Zip DriveA 100MB or 250MB read/write removable media disk drive.T Series.book  Page 86  Thursday, July 31, 2003  10:49 AM
105IndexIndexAACadapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33, 81indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15plug adapters   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67ACPI   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Active-Matrix Display  . . . . . . . . . . . . . . . . . . . . . . . . . 81ADSL  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Anti-theft Lock Slot  . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Auto/Airline Adapter  . . . . . . . . . . . . . . . . . . . . . . .33, 81BBattery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41alarm  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41care   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68charging indicator   . . . . . . . . . . . . . . . . . . . . . . . . . . 16cold-swapping   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42compartment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14conserving power  . . . . . . . . . . . . . . . . . . . . . . . . . . . 36dead  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57faulty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57increasing life  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68level indicators  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15lithium ion battery  . . . . . . . . . . . . . . . . . . . . . . .41, 83low  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57, 58recharging  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41replacing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41warm-swapping  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Battery Release Latch  . . . . . . . . . . . . . . . . . . . . . . . . . . . 9BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81guide   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34setup utility  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Boot  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Built-in Microphone   . . . . . . . . . . . . . . . . . . . . . . . . . . 13Button Icons  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21CCache Memory  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81CapsLock Indicator   . . . . . . . . . . . . . . . . . . . . . . . . . . . 16CardBus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81care   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Changing Tablet PC Button Functions   . . . . . . . . . . . 22Channels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Closed Cover Switch   . . . . . . . . . . . . . . . . . . . . . . . . . . 10CMOS RAM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Configuration Label  . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Conventions used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3CRT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20DDC in Connector   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9DC Output Cable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33DC Power Jack  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 33Default Value   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Device Ports   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48DIMM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43, 82DISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Display Panel   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10brightness  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18opening  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Display Panel Latch  . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Display Timeout  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37DMA   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82DMI  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82DNS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48Drive Image Special Edition (DISE) . . . . . . . . . . . . . . 63Drivers and Application Restore CD  . . . . . . . . . . . . . 64EECP   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Encryption Key (Network Key)   . . . . . . . . . . . . . . . . . 82Enlarging the Backup Partition . . . . . . . . . . . . . . . . . . 64Error Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61ESD   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82Extended Memory  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82External Monitor Port  . . . . . . . . . . . . . . . . . . . . . .13, 49FFloppy Diskcare   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Function KeyF10  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20F3  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20T Series.book  Page 105  Thursday, July 31, 2003  10:49 AM
106LifeBook T Series Tablet PC - IndexF4   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20F5   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20F6   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20F7   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20F8   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20F9   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20FN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20Fn  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20HHard Disk Driveaccess indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16problems   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . .  37Headphone Jack   . . . . . . . . . . . . . . . . . . . . . . . .  9, 11, 49Hibernate Mode   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37Hibernation Feature  . . . . . . . . . . . . . . . . . . . . . . . . . .  37IIDE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82IEEE 1394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  83Infrared Port   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13, 48Internal LAN Jack  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48IrDA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9, 48, 83IRQ  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  83KKeyboard  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10, 19cursor keys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19problems   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19LLAN (RJ-45) Jack   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13LifeBook Security Application Paneloperating  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  22uninstalling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24LifeBook Security/Tablet PC Buttons  . . . . . . . . .  10, 21LifeBook T Series Tablet PC specificationsadditional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74agency approval . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74display specifications   . . . . . . . . . . . . . . . . . . . . . . .  73environmental  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74physical specifications . . . . . . . . . . . . . . . . . . . .  73, 74power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74LifeBook Tablet PCunpacking   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7Local Area Network (LAN)   . . . . . . . . . . . . . . . . . . . . .  9MMemorycapacity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44compartment   . . . . . . . . . . . . . . . . . . . . . . . . . . .14, 43installing   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43upgrade module  . . . . . . . . . . . . . . . . . . . . . . . . . . . .43Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . .  9, 11, 49Microprocessor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73MIDI   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 12Modem (RJ-11) Port   . . . . . . . . . . . . . . . . . . . . . . .12, 48Modem Result Codes  . . . . . . . . . . . . . . . . . . . . . . . . . .62Mouseproblems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54See TouchpadMPU-401  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84NNTSC  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84Numeric Keypad  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19NumLk Indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Ooptional accessories   . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Additional Accessories  . . . . . . . . . . . . . . . . . . . . . . . .8additional accessories . . . . . . . . . . . . . . . . . . . . . . . . .8carrying cases   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8docking options   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8memory  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8power options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8storage options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8PParallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84PC Cardcare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69installing   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45slot  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 11PCI  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84PCMCIA   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84Pen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10calibrating the pen  . . . . . . . . . . . . . . . . . . . . . . . . . .27replacing the tip   . . . . . . . . . . . . . . . . . . . . . . . . . . . .28using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Pen and Active Digitizer . . . . . . . . . . . . . . . . . . . . . . . .27T Series.book  Page 106  Thursday, July 31, 2003  10:49 AM
107IndexPort Replicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46attaching  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14detaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54POST  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84PowerAC adapter   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Auto/Airline adapter  . . . . . . . . . . . . . . . . . . . . . . . .33failure   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56, 57indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15management  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33Power Management  . . . . . . . . . . . . . . . . . . . . . . . .36, 37Power On Self Test  . . . . . . . . . . . . . . . . . . . . . . . . . 34, 61Preparation for wireless LAN connection  . . . . . . . . . 93RRegistration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Re-Installing Individual Drivers and Applications  . .64Restarting the system  . . . . . . . . . . . . . . . . . . . . . . . . . . 37Restoring a Backup Image  . . . . . . . . . . . . . . . . . . . . . . 64Restoring Your Pre-installed Software  . . . . . . . . . . . . 63RJ-11  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48RJ-45  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 48Rotation Hinge  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10SScrLk Indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16SDRAM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14, 43Security Indicator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Security Lock Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Serial Port  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85Setting Up LifeBook Security Panel  . . . . . . . . . . . . . . 22Shut Down   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38SMART  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85Smart Card Reader  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Specifications   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73SRAM   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85SSID  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Status Indicator Panel   . . . . . . . . . . . . . . . . . . . . . . 10, 15Suspend  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36, 85Suspend/Resume Button  . . . . . . . . . . . . . . . . . .9, 12, 36S-Video  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86TTablet Dock Port   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Tablet PCcare   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67storing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67traveling   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86Touch Screenclicking   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Touchpadclicking   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 25control adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 26double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25dragging   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53battery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54hard drive  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55mouse/keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . .54PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56port replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56video   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59UUniversal Serial Bus Port  . . . . . . . . . . . . . . . . . . . . . . . 48USB   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56USB Port  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 13Using the Active Digitizer  . . . . . . . . . . . . . . . . . . . . . . 28Using the System as a Tablet  . . . . . . . . . . . . . . . . . . . . 17VVolume Control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29WWarm-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42WFM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Wi-Fi Compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Windowsend user license agreement  . . . . . . . . . . . . . . . . . . . 35Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Start key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Wireless LANAd Hoc Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90before using the wireless LAN . . . . . . . . . . . . . . . . . 90Broadcom wireless LAN   . . . . . . . . . . . . . . . . . . . . . 90T Series.book  Page 107  Thursday, July 31, 2003  10:49 AM
108LifeBook T Series Tablet PC - Indexconnection using Windows XP  . . . . . . . . . . . . . . .  93for better communications   . . . . . . . . . . . . . . . . . .  91Infrastructure Mode  . . . . . . . . . . . . . . . . . . . . . . . .  90Intel PROSet wireless LAN . . . . . . . . . . . . . . . . . . .  90IP address information . . . . . . . . . . . . . . . . . . . . .  102other settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99setting of power-saving function . . . . . . . . . . . . . .  99specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  103starting transmission   . . . . . . . . . . . . . . . . . . . . . . .  92stopping transmission   . . . . . . . . . . . . . . . . . . . . . .  92troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .  100Wireless LAN On-Off Switch . . . . . . . . . . . . . . . . .  9, 13WLAN   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  86T Series.book  Page 108  Thursday, July 31, 2003  10:49 AM

Navigation menu