Fujitsu Client Computing WL0009 LifeBook P Series w/WLL4070 11ABG WLAN User Manual P7010

Fujitsu Limited LifeBook P Series w/WLL4070 11ABG WLAN P7010

Users Manual

CopyrightCopyright and Trademark InformationFujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. The absence of a product or service name, slogan, or logo does not constitute a waiver of any trademark or other intellectual property rights relating to that name, slogan, or logo owned by Fujitsu Computer Systems Corporation, its parent, subsidiaries, and affiliated companies.Fujitsu, the Fujitsu logo, and LifeBook are registered trade-marks of Fujitsu Limited.Intel and Pentium are registered trademarks and Centrino is a trademark of Intel Corporation or its subsidiaries in the United States and other countries.IBM, IBM PC AT, and IBM PS/2 are registered trademarks of IBM Corporation in the United States, other countries, or both. MS, MS-DOS, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.PCMCIA is a trademark of the Personal Computer Memory Card International Association.Memory Stick and Memory Stick Duo are trademarks of Sony, its parent, and/or its affiliates.Adobe, Acrobat, and Acrobat Reader are either registered trade-marks or trademarks of Adobe Systems, Incorporated in the United States and/or other countries.Dolby Headphone manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. Quicken is a registered trademark and/or registered service mark of Intuit, Inc. or one of its subsidiaries in the United States and other countries.InterVideo and WinDVD are registered trademarks of Inter-video, Inc.Realtek is a registered trademark of Realtek Semiconductor Corporation.Norton AntiVirus is a registered trademark of Symantec Corporation in the United States and other countries.This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection tech-nology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.All other trademarks mentioned herein are the property of their respective owners.© Copyright 2004 Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, translated, stored, or transmitted in any electronic form without the written consent of Fujitsu Computer Systems Corporation. B6FH-4971-01EN-00W a rn in gHandling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Was h hands  after handling.DECLARATION OF CONFORMITYaccording to FCC Part 15Responsible Party Name: Fujitsu Computer Systems CorporationAddress:  1250 E. Arques AvenueSunnyvale, CA 94085Telephone: (408) 746-6000Declares that product: Base Model Configurations:LifeBook P1510 notebookLifeBook P1510D notebookComplies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:(1) This device must not be allowed to cause harmful interference, (2) This device must accept anyinterference received, including interference that may cause undesired operation.P7010.book  Page 1  Monday, December 20, 2004  1:57 PM
LifeBook P7000 NotebookUL Notice This unit requires an AC adapter to operate. Use only UL Listed Class 2 Adapters with an output rating of 16 VDC, with a current of 3.75A minimum.AC Adapter output polarity:■When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:■Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.■Avoid using the modem during an electrical storm. There may be a remote risk of electric shock from lightning.■Do not use the modem to report a gas leak in the vicinity of the leak.■Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.■To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line CordSAVE THESE INSTRUCTIONSFor Authorized Repair Technicians OnlySystem Disposal+■For continued protection against risk of fire, replace only with the same type and rating fuse.■Danger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dis-pose of used batteries according to the manufacturer’s instruction.Hg          LAMP(S) INSIDE THIS PRODUCT            CONTAIN MERCURY AND MUST          BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, ORFEDERAL LAWS.P7010.book  Page 2  Monday, December 20, 2004  1:57 PM
Table of ContentsFujitsu LifeBook® P7000 NotebookTable of Contents1PREFACEPrefaceAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . .1Fujitsu Contact Information . . . . . . . . . . . . . . . . .1Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12GETTING TO KNOW YOUR LIFEBOOK NOTEBOOKOverviewUnpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Locating the Controls/ConnectorsTop and Front Components . . . . . . . . . . . . . . . . .6Left-Side Panel Components  . . . . . . . . . . . . . . . .8Right-Side Panel Components  . . . . . . . . . . . . . . .9Rear Panel Components . . . . . . . . . . . . . . . . . . .10Bottom Components  . . . . . . . . . . . . . . . . . . . . .11Status Indicator PanelBattery Charging Indicators  . . . . . . . . . . . . . . . .12Battery Level Indicators  . . . . . . . . . . . . . . . . . . .12Hard Disk/CD Access Indicator. . . . . . . . . . . . . .12KeyboardUsing the Keyboard . . . . . . . . . . . . . . . . . . . . . .13Key Indicator Lights . . . . . . . . . . . . . . . . . . . . . .13Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . .13Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .13Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . .14Touchpad Pointing DeviceClicking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . .15Dragging  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Touchpad Control Adjustment . . . . . . . . . . . . . .16Volume ControlControlling the Volume  . . . . . . . . . . . . . . . . . . .17Flexible Bay DevicesRemoving and Installing Modular Devices  . . . . .183GETTING STARTED WITH YOUR LIFEBOOK NOTEBOOKPower SourcesConnecting the Power Adapters . . . . . . . . . . . . .23Display PanelOpening the Display Panel . . . . . . . . . . . . . . . . .24Adjusting Display Panel Brightness . . . . . . . . . . .24Closing the Display Panel . . . . . . . . . . . . . . . . . .24Starting Your LifeBook NotebookPower On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . .25BIOS Setup Utility. . . . . . . . . . . . . . . . . . . . . . . .25Booting the System  . . . . . . . . . . . . . . . . . . . . . .26Registering Your LifeBook notebook. . . . . . . . . .26Installing Click Me!. . . . . . . . . . . . . . . . . . . . . . .26Power ManagementSuspend/Resume/Power On Button. . . . . . . . . .27Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . .27Hibernation Feature . . . . . . . . . . . . . . . . . . . . . .27Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . .28P7010.book  Page 3  Monday, December 20, 2004  1:57 PM
LifeBook P7000 NotebookHard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . 28Windows Power Management . . . . . . . . . . . . . . 28Restarting the System. . . . . . . . . . . . . . . . . . . . . 28Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284USER-INSTALLABLE FEATURESLithium ion BatteryRecharging the Batteries. . . . . . . . . . . . . . . . . . . 31Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 32External Floppy Disk DriveLoading a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 33Ejecting a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 33Preparing a Disk for Use. . . . . . . . . . . . . . . . . . . 33Optical DriveMedia Player Software . . . . . . . . . . . . . . . . . . . . 34Loading a DVD or CD  . . . . . . . . . . . . . . . . . . . . 34Removing Media . . . . . . . . . . . . . . . . . . . . . . . . 35Using the Optical Drive Software . . . . . . . . . . . . 35Using DolbyTM Headphone. . . . . . . . . . . . . . . . 35Using the Optical Drive on Battery Power  . . . . . 36Auto Insert Notification Function . . . . . . . . . . . . 36Emergency Tray Release. . . . . . . . . . . . . . . . . . . 36PC CardsInstalling PC Cards . . . . . . . . . . . . . . . . . . . . . . . 37Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . 37Compact Flash CardsInstalling CF Cards . . . . . . . . . . . . . . . . . . . . . . . 38Removing CF Cards . . . . . . . . . . . . . . . . . . . . . . 39Memory Stick/Secure Digital SlotInstalling Memory Stick/SD Cards  . . . . . . . . . . . 40Removing A Memory Stick/SD Card  . . . . . . . . . 41Memory Upgrade ModuleAccessing the Memory Compartment  . . . . . . . . 42Removing a Memory Module. . . . . . . . . . . . . . . 42Installing a Memory Module  . . . . . . . . . . . . . . . 42Checking the Memory Capacity . . . . . . . . . . . . . 43Device PortsModem (RJ-11) Telephone Port. . . . . . . . . . . . . 44Internal LAN (RJ-45) Port. . . . . . . . . . . . . . . . . . 44IEEE 1394 Port . . . . . . . . . . . . . . . . . . . . . . . . . . 45S-Video Out Port (TV Out)  . . . . . . . . . . . . . . . . 45Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . 45Headphone Jack  . . . . . . . . . . . . . . . . . . . . . . . . 45Optical Digital Audio Connector  . . . . . . . . . . . . 46Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 46External Monitor Port  . . . . . . . . . . . . . . . . . . . . 465WIRELESS LAN USER’S GUIDEBefore Using the Wireless LANWireless LAN Modes Using this Device  . . . . . . . 50Wireless Network Considerations. . . . . . . . . . . . 51Deactivating the WLAN Device . . . . . . . . . . . . . 51Activating the WLAN Device . . . . . . . . . . . . . . . 52Configuration of the WLAN DeviceFlow of Operations  . . . . . . . . . . . . . . . . . . . . . . 53Configuration Using Intel PROSet Software . . . . 53Configuration Using      Atheros Client Utility Software  . . . . . . . . . . 54Connection to the network  . . . . . . . . . . . . . . . . 55Troubleshooting the WLANTroubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 60Wireless LAN GlossaryGlossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61IP address informationAbout IP Addresses . . . . . . . . . . . . . . . . . . . . . . 63WLAN SpecificationsSpecification  . . . . . . . . . . . . . . . . . . . . . . . . . . . 63P7010.book  Page 4  Monday, December 20, 2004  1:57 PM
Table of Contents6TROUBLESHOOTINGTroubleshootingIdentifying the Problem . . . . . . . . . . . . . . . . . . .67Specific Problems . . . . . . . . . . . . . . . . . . . . . . . .67Troubleshooting Table . . . . . . . . . . . . . . . . . . . .68Power On Self Test Messages. . . . . . . . . . . . . . .75Emergency DVD Tray Release  . . . . . . . . . . . . . .76Modem Result Codes . . . . . . . . . . . . . . . . . . . . .76Restoring Pre-installed SoftwareRestoring the Factory Image. . . . . . . . . . . . . . . .77Automatically Downloading Driver Updates . . . .787CARING FOR YOUR LIFEBOOK NOTEBOOKCare and MaintenanceBatteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82Floppy Disks and Drives . . . . . . . . . . . . . . . . . . .82Media Care  . . . . . . . . . . . . . . . . . . . . . . . . . . . .83PC Cards  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .838SYSTEM SPECIFICATIONSSpecificationsConfiguration Label . . . . . . . . . . . . . . . . . . . . . .87Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . .87Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Mass Storage Device Options. . . . . . . . . . . . . . .87Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .88Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88Dimensions and Weight . . . . . . . . . . . . . . . . . . .88Environmental Requirements . . . . . . . . . . . . . . .88Popular Accessories  . . . . . . . . . . . . . . . . . . . . . .88Pre-Installed Software  . . . . . . . . . . . . . . . . . . . .89Learning About Your Application Software. . . . .89Regulatory Information  . . . . . . . . . . . . . . . . . . .91Notice  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .919GLOSSARYGlossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95APPENDIX A: USING THE FINGERPRINT SENSOR DEVICEFingerprint Sensor DeviceIntroducing the Optional      Fingerprint Sensor Device  . . . . . . . . . . . . .101Getting Started. . . . . . . . . . . . . . . . . . . . . . . . .101Installing OmniPass  . . . . . . . . . . . . . . . . . . . . .101User Enrollment . . . . . . . . . . . . . . . . . . . . . . . .102Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . .103Configuring OmniPass . . . . . . . . . . . . . . . . . . .105OmniPass Control Center. . . . . . . . . . . . . . . . .106Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .107INDEXIndex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109P7010.book  Page 5  Monday, December 20, 2004  1:57 PM
LifeBook P7000 NotebookP7010.book  Page 6  Monday, December 20, 2004  1:57 PM
1PrefaceP7010.book  Page 1  Monday, December 20, 2004  1:57 PM
LifeBook P7000 NotebookP7010.book  Page 2  Monday, December 20, 2004  1:57 PM
1PrefacePrefaceABOUT THIS GUIDEThe LifeBook P7000/P7000D Series notebook from Fujitsu Computer Systems Corporation is a small but powerful computer. It is powered by an Intel Pentium M processor Ultra-low Voltage (ULV) or an Intel Celeron 852 GML processor, has a built-in wide-aspect Crystal View color display, and brings the functionality of desktop personal computers (PCs) to a portable envi-ronment.This manual explains how to operate your LifeBook notebook’s hardware and built-in system software. It comes with Microsoft Windows® XP Home or Window XP Pro pre-installed.Conventions Used in the GuideKeyboard keys and on-screen buttons appear in brackets. Example: [Fn], [F1], [ESC], and [CTRL].Pages with additional information about a specific topic are cross-referenced within the text.Example: (See page xx.)DOS commands you enter appear in Courier type. Example: Shutdown the computer?FUJITSU CONTACT INFORMATIONService and SupportYou can contact Fujitsu Service and Support in the following ways:■Toll free: 1-800-8Fujitsu (1-800-838-5487)■Fax: (408) 764-2724 ■E-mail: 8fujitsu@us.fujitsu.com ■Web site: http://www.computers.us.fujitsu.com/supportBefore you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:■Product name■Product configuration number■Product serial number■Purchase date■Conditions under which the problem occurred■Any error messages that have occurred■Type of device connected, if anyFujitsu OnlineYou can go directly to the online Fujitsu Product catalog for your LifeBook notebook by clicking on the Fujitsu Weblinks -> LifeBook Accessories Web site URL link, located in the Windows Start menu.You can also reach Fujitsu Service and Support online by clicking on the Fujitsu Weblinks -> Service and Support Web site URL link, located in the Windows Start menu.WARRANTYYour LifeBook notebook is backed by an International Limited Warranty. Check the service kit that came with your notebook for warranty terms and conditions.The information icon highlights information that will enhance your understanding of the subject material.The caution icon highlights information that is important to the safe operation of your computer, or to the integrity of your files. Please read all caution information carefully.The warning icon highlights information that can be hazardous to either you, your LifeBook notebook, or your files. Please read all warning information carefully.You must have an active internet connec-tion to use the online URL links.P7010.book  Page 1  Monday, December 20, 2004  1:57 PM
2LifeBook P7000 Notebook – Section OneP7010.book  Page 2  Monday, December 20, 2004  1:57 PM
32Getting to KnowYour LifeBook NotebookP7010.book  Page 3  Monday, December 20, 2004  1:57 PM
4LifeBook P7000 Notebook – Section TwoP7010.book  Page 4  Monday, December 20, 2004  1:57 PM
5Getting to Know Your LifeBook Figure 2-1 Fujitsu LifeBook P7000 notebookOverviewThis section describes the components of your Fujitsu LifeBook P7000 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers.UNPACKINGWhen you receive your LifeBook notebook, unpack it carefully, and compare the parts you have received with the items listed below.■LifeBook P7000/P7000D notebook(Figure 2-1)■AC adapter with AC power cord (Figure 2-2)■Lithium ion battery■Weig h t  S aver■Phone/Modem (RJ-11) telephone cable■Driver and Application Restore CD■Getting Started Guide■User’s Guide (this document)■International Limited Warranty Brochure■Certification of Authenticity Depending upon the configuration of your system, one or more of the following items may also be included:■Modular DVD/CD-RW Combo Drive■Modular Multi-Format DVD Writer■External Floppy Disk Drive ■Modular 2nd battery■Additional main high capacity battery■RecordNow CD (included with Combo drive)■RecordNow and WinDVD Creator CD (included with Multi-Format DVD Writer)Once you have checked and confirmed that your Life-Book system is complete, read through the following pages to learn about all of your notebook’s components. Figure 2-2 AC AdapterP7010.book  Page 5  Monday, December 20, 2004  1:57 PM
6LifeBook P7000 Notebook – Section TwoFigure 2-3 LifeBook notebook with display openLocating the Controlsand ConnectorsTOP AND FRONT COMPONENTSThe following is a brief description of your LifeBook notebook’s top and front components. Wireless LAN On/Off SwitchAllows you to turn the optional Wireless LAN device on and off. Note that this switch is present on all models of the LifeBook P7000 notebook, but it is functional only on those with an optional Wireless LAN installed. Built-in MicrophoneThe built-in microphone allows you to input or record mono audio.SD/Memory Stick SlotThe Secure Digital (SD)/Memory Stick slot allows you to install a flash memory card for data storage. This archi-tecture allows you to transfer data between a variety of different digital devices. (See Installing Memory Stick/SD Cards on page 40 for more information)Touchpad Pointing Device/Scroll ButtonThe Touchpad pointing device is a mouse-like cursor control with three buttons (left, right, and scroll* button). (See Touchpad Pointing Device on page 15 for more information). *  Certain configurations of this system have an optional fingerprint sensor located in place of the scroll button. If you have a system with the optional fingerprint sensor, refer to (See Fingerprint Sensor Device on page 101 for more information) Num Lock/Scroll Lock/Caps Lock IndicatorThese indicators light up when the num lock, scroll lock, or caps lock buttons have been turned on. (See Using the Keyboard on page 13 for more information).KeyboardA full-size keyboard with dedicated Windowskeys. (See Keyboard on page 13 for more information)Stereo SpeakersThe built-in dual box speakers allow for stereo sound. Display PanelStatus Indicator PanelKeyboardStereo SpeakersSuspend/Resume/ Power On ButtonWireless LAN On/Off SwitchTouchpad Pointing Device*Num Lock IndicatorCaps Lock IndicatorScroll Lock IndicatorMicrophoneSD/Memory Stick Slot* Touchpad may have scroll button or     optional fingerprint sensor device. P7010.book  Page 6  Monday, December 20, 2004  1:57 PM
7Getting to Know Your LifeBookSuspend/Resume/Power On ButtonThe Suspend/Resume/Power On button allows you to suspend notebook activity without powering off, resume your LifeBook notebook from suspend mode, and power on your notebook when it has been shut down from Windows. (See Suspend/Resume/Power On Button on page 27 for more information)Status Indicator PanelThe Status Indicator Panel displays symbols that corre-spond with a specific component of your LifeBook note-book. (See Status Indicator Panel on page 12 for more information)Display PanelThe display panel is a color LCD panel with back lighting for the display of text and graphics. P7010.book  Page 7  Monday, December 20, 2004  1:57 PM
8LifeBook P7000 Notebook – Section TwoFigure 2-4 LifeBook notebook left-side panelLEFT-SIDE PANEL COMPONENTSThe following is a brief description of your LifeBook notebook’s left-side components. PC Card SlotThe PC Card Slot allows you to install one Type II PC Card. (See PC Cards on page 37 for more information)PC Card Eject ButtonThe PC Card eject button allows you to remove PC Cards from the PC Card slot. (See PC Cards on page 37 for more information)Compact Flash Card SlotAllows you to insert a compact flash (CF) card. (See Compact Flash Cards on page 38 for more information)Compact Flash Card Eject ButtonAllows you to eject a compact flash card. (See Removing CF Cards on page 39 for more information)Flexible BayThe Flexible Bay can accommodate either the standard DVD/CD-RW Drive or an optional modular bay battery. If neither device is installed, the weight saver should be installed. (See Flexible Bay Devices on page 18 for more information)Modem (RJ-11) Telephone PortThe Modem (RJ-11) telephone port is for attachinga telephone line to the internal multinational 56K modem. (See Modem (RJ-11) Telephone Port on page 44 for more information)DC Power JackThe DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your note-book and charge the internal Lithium ion battery. Modem PortCompact Flash SlotCompact Flash Card Eject ButtonDC Power JackFlexible BayPC Card SlotPC Card Eject ButtonThe internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire notebook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.The internal multinational modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600bps at upload. For additional information about the multinational modem, refer to the Fujitsu web site at: us.fujitsu.com/computers.P7010.book  Page 8  Monday, December 20, 2004  1:57 PM
9Getting to Know Your LifeBookFigure 2-5  LifeBook notebook right-side panel RIGHT-SIDE PANEL COMPONENTSThe following is a brief description of your LifeBook notebook’s right-side components. LAN (RJ-45) PortThe internal LAN (RJ-45) port is used for an internal Fast Ethernet (10/100 Base-TX) connection.(See Internal LAN (RJ-45) Port on page 44 for more infor-mation)IEEE 1394 Port The IEEE 1394 port (also known as “Firewire”) is used to connect between your LifeBook and a peripheral such as a digital video camera.(See IEEE 1394 Port on page 45 for more information)S-Video Out PortThe S-video out port is used to transmit a higher resolu-tion video signal to a compatible TV or VCR. (See S-Video Out Port (TV Out) on page 45 for more information)External Monitor PortThe external monitor port allows you to connect your LifeBook notebook to an external monitor. (See External Monitor Port on page 46 for more information)Port Access DoorsThe port access doors are designed to protect the ports when they are not in use.USB 2.0 PortsThe USB ports allow you to connect Universal Serial Bus 2.0 devices. (See Universal Serial Bus Ports on page 45 for more information)Microphone JackThe microphone jack allows you to connect an external mono microphone. (See Microphone Jack on page 46 for more information)Headphone/Optical Digital Audio JackThe headphone/optical digital audio jack allows you to connect headphones or to download digital audio onto a MiniDisc recorder’s SPDIF (Sony Philips Digital Inter-face) format. (See Optical Digital Audio Connector on page 46 for more information)USB PortsMicrophone JackHeadphone/OpticalDigital Audio OutJack Port Access Doors(open)External Monitor PortS-Video Out PortIEEE 1394 PortLAN (RJ-45) PortP7010.book  Page 9  Monday, December 20, 2004  1:57 PM
10LifeBook P7000 Notebook – Section TwoFigure 2-6  LifeBook notebook rear panelREAR PANEL COMPONENTSThe following is a brief description of your LifeBook notebook’s rear components.Anti-theft Lock SlotThe anti-theft lock slot allows you to attach an optional physical lock down device. Air VentsThe air vents allow for proper cooling of the system while it is operating.Air VentsAnti-theft Lock SlotP7010.book  Page 10  Monday, December 20, 2004  1:57 PM
11Getting to Know Your LifeBookFigure 2-7 LifeBook notebook bottom panelBOTTOM COMPONENTSThe following is a brief description of your LifeBook notebook’s bottom panel components. Lithium ion Battery The internal Lithium ion battery can be installed in the battery bay by aligning it with the slides and pushing it into place. The battery can be removed when swapping with a charged battery, or when the computer is to be stored for a long period of time. (See Lithium ion Battery on page 31 for more information)Battery Release LatchesSlide the battery releases to unlatch the battery. Memory Module CoverRemovable cover over the memory modules. (See Removing a Memory Module on page 42 for more infor-mation)Flexible Bay Release LatchThe Flexible Bay Release Latch releases the flexible bay device for removal. (See Removing and Installing Modular Devices on page 18 for more information)Main Unit and Configuration LabelThe configuration label shows the model number and other information about your LifeBook notebook. In addition, the configuration portion of the label has the serial number and manufacturer information that you will need to give your support representative. It identi-fies the exact version of various components of your notebook. Air VentsThe air vents allow for proper cooling of the system while it is operating.Main Lithium ion BatteryMain Unit andConfiguration Label(approximate location)Memory Module CoverAir VentsFlexible Bay Release LatchBattery Release LatchesP7010.book  Page 11  Monday, December 20, 2004  1:57 PM
12LifeBook P7000 Notebook – Section TwoFigure 2-8 Status Indicator PanelStatus Indicator PanelThe Status Indicator displays symbols that correspond with a specific component of your LifeBook notebook. These symbols (when visible) tell you how each of those components is operating. (Figure 2-8). When you turn off the system, all indicators will go off, except when the battery is being charged. BATTERY CHARGING INDICATORSWhen the AC adapter is connected to your system, these indicators show the status of the specified battery charging (either the primary battery 1 or modular battery 2), as follows:■Green, solid: The battery is either fully charged or the AC adapter is connected and there is no battery pack installed.■Orange, solid: The battery pack is charging.■Orange, blinking: Charging is suspended due to exces-sively high or low battery temperature. ■Off: No AC adapter is connected. BATTERY LEVEL INDICATORSThe Battery Level indicators display the charge level of the indicated battery pack, as follows:■Green, solid: Battery is between 51% and 100% charged.■Orange, solid: Battery is between 13% and 50% charged.■Red, solid: Battery is between 0% and 12% charged.■Orange, blinking: Blinks during battery status measurement (Four seconds after the battery is installed).■Red, blinking: There is a problem with the battery.■Off: There is no battery installed. HARD DISK/CD ACCESS INDICATORThe Hard Disk/CD access indicator lights when the hard disk or optical drive is being accessed. To prevent corruption of data, do not press the power button when the hard disk/CD access indicator is lit. Battery 1 Level IndicatorHard Drive/Optical Drive Battery 1ChargingIndicator AccessBattery 2ChargingIndicatorBattery 2 Level Indicator■ If the battery pack is installed while the power is turned off, the battery level indicator will display the charge level for five seconds after it blinks orange.■If the AC adapter is not connected or the battery pack is not fully charged when the computer is switched to standby mode, the indicator will blink. The LED blinks at the rate of one second on/five seconds off. ■Batteries subjected to shocks, vibration or extreme temperatures can be perma-nently damaged.■A shorted battery is damaged and must be replaced.P7010.book  Page 12  Monday, December 20, 2004  1:57 PM
13Getting to Know Your LifeBookFigure 2-9  KeyboardKeyboard USING THE KEYBOARDYour Fujitsu LifeBook notebook has an integral 82-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys. (Figure 2-9)■Numeric keypad: Your notebook allows certain keys to serve dual purposes, both as standard characters and as numeric and mathematical keys. The ability to tog-gle between the standard character and numerical keys is controlled through the [NumLk] key.■Cursor keys: Your keyboard contains four arrowkeys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. ■Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. ■Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right buttonon your pointing device.KEY INDICATOR LIGHTSThere are three small indicator lights located on the lower right of the palm rest. (Figure 2-10). When lit, these lights indicate that the related key is locked. Figure 2-10  Key IndicatorsNUMERIC KEYPADCertain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] keys. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ),multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary functions. (Figure 2-9) WINDOWS KEYSYour LifeBook notebook has two Windows keys, consisting of a Start key and an Application key. The Start key displays the Start menu. This button functions the same as your onscreen Start menu button. The Fn Key WindowsFunction KeysNumeric KeypadCursor KeysWindowsApplication KeyStart KeyNum Lock IndicatorCaps Lock Indicator Scroll Lock Indicator P7010.book  Page 13  Monday, December 20, 2004  1:57 PM
14LifeBook P7000 Notebook – Section TwoApplication key functions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows documentation for additional information regarding the Windows keys.) (Figure 2-9)CURSOR KEYSThe cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right). (Figure 2-9)FUNCTION KEYSYour LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. (Figure 2-9)The [Fn] key provides extended functions for thenotebook and is always used in conjunction with another key. ■[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.■[Fn+F4]: Pressing [F4] while holding [Fn] will toggle the Quick Point feature on and off. Note that the [Fn+F4] combination only works if Manual Setting is selected in the BIOS. (See “Entering the BIOS Setup Utility” on page 25)■[Fn+F5]: Pressing [F5] while holding [Fn] allows you to toggle between video compensation and no compensation. (Video compensation controls spacing on the display. When it is enabled, displays with 1024 x 768 or 800 x 600 pixel resolution will still cover the entire screen.) Note that this function is only applicable if Compensation is disabled in the BIOS. (See BIOS Setup Utility on page 25 for more informa-tion).■[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.*■[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.*■[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your LifeBook note-book.**■[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your LifeBook notebook.**■[Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, both built-in display panel and external monitor or external monitor only.* There are eight brightness levels.** There are 26 audio levels.P7010.book  Page 14  Monday, December 20, 2004  1:57 PM
15Getting to Know Your LifeBookFigure 2-11 Touchpad pointing deviceTouchpad Pointing DeviceThe Touchpad pointing device comes built into your LifeBook notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left and right button, and a scrolling button. The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger. The left and right buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending on the application that is being used. The scrolling button allows you to navi-gate quickly through pages, without having to use the scroll bars. (Figure 2-15)CLICKINGClicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the Touchpad once. (Figure 2-12)Figure 2-12 ClickingDOUBLE-CLICKINGDouble-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and then immediately release it. You also have the option to perform the double-click operation by tapping lightly on the Touchpad twice. (Figure 2-13)Figure 2-13  Double-clickingCursor ControlLeft ButtonRight ButtonScroll ButtonCursor(or optionalfingerprint sensor)Certain configurations of the LifeBook P7000 notebook have an optional finger-print sensor instead of a scrolling button. For information on using the optional fin-gerprint sensor, refer to “Fingerprint Sen-sor Device” on page 101.P7010.book  Page 15  Monday, December 20, 2004  1:57 PM
16LifeBook P7000 Notebook – Section TwoDRAGGINGDragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap. Next, move the object to its new location by moving your finger across the Touchpad, and then release your finger. (Figure 2-14)Figure 2-14  DraggingSCROLLINGUsing the Scrolling button allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navigating through on-line pages. To use the Scrolling button, press the crescent shape at the top or bottom of the button to scroll up or down a page. When you have reached the desired section of the page, release the button. (Figure 2-15)If you have an optional fingerprint sensor in the location of the Scrolling button, you can scroll by sliding your finger up and down the fingerprint sensor.(Figure 2-16). Note that you can also scroll by sliding your finger up and down the right side of the touchpad. This feature is disabled by default, but you can enable it by going to Start -> Control Panel -> Mouse.Figure 2-15 Scrolling with scrolling buttonFigure 2-16 Scrolling with TouchpadTOUCHPAD CONTROL ADJUSTMENTIf you need to change or adjust any of the touchpad control functions, you can customize them from the Mouse properties dialog box in the Control Panel. Click on Start, select Settings > Control Panel, then double-click Mouse. ■If the interval between clicks is too long, the double-click will not be executed.■Parameters for the Touchpad can be adjusted from the Mouse Properties dialog box located in the Windows Control Panel.P7010.book  Page 16  Monday, December 20, 2004  1:57 PM
17Getting to Know Your LifeBookVolume ControlYour Fujitsu LifeBook notebook has multiple volume controls which interact with each other. CONTROLLING THE VOLUMEThe volume can be controlled in several different ways:■Volume can be set from within the Volume Control on the Taskbar.■Volume can be controlled with the [F8] and [F9] functions keys. Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your notebook. Press-ing [F9] repeatedly while holding [Fn] will increase the volume of your notebook.■Volume can be controlled by many volume controls that are set within individual applications.■Certain external audio devices you might connect to your system may have hardware volume controls.Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources. We recommend that you experiment with the various volume controls to discover the optimal sound level.Any software that contains audio files will also contain a volume control of its own. If you install an external audio device that has an independent volume control, the hardware volume control and the software volume control will interact with each other. It should be noted that if you set your software volume to Off, you will override external volume control settings. There are 26 levels through which the function keys cycle. P7010.book  Page 17  Monday, December 20, 2004  1:57 PM
18LifeBook P7000 Notebook – Section TwoFigure 2-17 Flexible BayFlexible Bay DevicesYour Fujitsu LifeBook notebook contains a Flexible Bay. The Flexible Bay can accommodate a modular Multi-Format DVD Writer, a modular DVD/CD-RW combo drive, a modular Lithium ion battery, or a weight saver. (Figure 2-17)■Modular Multi-Format DVD Writer: This allows you to access movies, software, and audio DVD/CDs and record to DVD+RW, CD-R/RW, and DVD-RAM discs.■Modular DVD/CD-RW combo drive: This allows you to access movies, software, and audio DVD/CDs as well as to write to CDs. ■Modular Lithium ion battery: This is a rechargeablebattery that can be used to power your LifeBook note-book when an adapter is not connected.■Weight Saver: This is used to fill the bay when no device is installed.REMOVING AND INSTALLINGMODULAR DEVICES To remove and install modular devices in the Flexible Bay, you can perform either a cold-swapping or hot-swapping of the device. Cold-swapping means swapping devices while your LifeBook notebook is powered off. Hot-swapping occurs when your system is powered on with a charged main battery or AC Adapter.Cold-swappingTo cold-swap modular devices in your Flexible Bay follow these easy steps: 1. Close any open files.2. Shut down your LifeBook notebook.3. Turn the system over and slide the release latch (Figure 2-18). Pull out the Flexible Bay device from the slot. Figure 2-18 Removing a device from the Flexible BayFigure 2-19 Installing a device in the Flexible BayFlexible BayYou should never leave your Flexible Bay empty when the notebook is in operation. If left empty, dust or foreign matter may accumulate inside the notebook.Be careful when aligning and seating devices in the bay. If the fit is incorrect, you may damage the bay or the device. If the device does not move easily in the bay, remove it, and check for dirt or foreign objects. It will require a firm push to latch the device in place.Flexible Bay Release LatchP7010.book  Page 18  Monday, December 20, 2004  1:57 PM
19Getting to Know Your LifeBook5. Slide the device you are installing into your note-book until it clicks into place. (Figure 2-19)6. It is now safe to turn your notebook back on.7. You can now access and use the device.Your LifeBook notebook will automatically detect the new device and activate it within your system. The drive letters associated with the device will be created and listed under My Computer and Windows Explorer. Hot-swappingTo hot-swap Flexible Bay devices while the system is powered on, follow these steps:1. Prior to performing the hot-swap, make sure you have a charged main battery installed, or an AC Adapter is powering the system.2. If your system is in Suspend mode, press the Suspend/Resume button to resume operation.3. Click the Safely Remove Hardware icon in the lower right-hand corner of the screen.4. From the list that appears, click the device you want to remove.5. Pull out the Flexible Bay eject lever. This will push your device out slightly, allowing you to remove the device.6. Slide your device out until it is clear of the bay.This will require light force.7. Slide the device you are installing into yournotebook until it clicks into place.8. You can now access and use the device.Your LifeBook notebook will automatically detect the new device and activate it within your system. The drive letters associated with the device will be created and listed under My Computer and Windows Explorer. Be careful when aligning and seating devices in the bay. If the fit is incorrect, you may damage the bay or the device. If the device does not move easily in the bay, remove it, and check for dirt or foreign objects. It will require a firm push to latch the device in place.P7010.book  Page 19  Monday, December 20, 2004  1:57 PM
20LifeBook P7000 Notebook – Section TwoP7010.book  Page 20  Monday, December 20, 2004  1:57 PM
213Getting StartedP7010.book  Page 21  Monday, December 20, 2004  1:57 PM
22LifeBook P7000 Notebook – Section ThreeP7010.book  Page 22  Monday, December 20, 2004  1:57 PM
23Getting StartedFigure 3-1 Connecting the AC AdapterPower SourcesYour Fujitsu LifeBook notebook has four possible power sources: a primary Lithium ion battery, an optional modular Lithium ion battery, an AC adapter, or an optional Auto/Airline adapter.CONNECTING THE POWER ADAPTERSThe AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter1. Plug the DC output cable into the DC power jackof your LifeBook notebook.2. Plug the AC adapter into an AC electrical outlet. (Figure 3-1)Connecting the Optional Auto/Airline Adapter1. Plug the DC output cable into the DC power jackon your notebook.2. Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key inthe On or Accessories position.OR3. Plug the Auto/Airline adapter into the DC power jack on an airplane seat.Switching from AC Adapter Power or theAuto/Airline Adapter to Battery Power1. Be sure that you have at least one chargedbattery installed.2. Remove the AC adapter or the Auto/Airline adapter.DC Power JackDC Output CableAC AdapterAC CableThe Lithium ion battery is not charged upon purchase. Initially, you will need to connect either the AC adapter or the Auto/Airline adapter to use your notebook.P7010.book  Page 23  Monday, December 20, 2004  1:57 PM
24LifeBook P7000 Notebook – Section ThreeFigure 3-2 Opening the Display PanelDisplay PanelYour Fujitsu LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of active-matrix technology. OPENING THE DISPLAY PANELLift the display backwards, being careful not to touch the screen, until it is at a comfortable viewing angle. (Figure 3-2)ADJUSTING DISPLAY PANEL BRIGHTNESSOnce you have turned on your LifeBook notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness, by using the keyboard or the power management utility. Using the KeyboardAdjusting the brightness using the keyboard changes the setting only temporarily. ■[Fn+F6]: Pressing repeatedly will lower thebrightness of your display.■[Fn+F7]: Pressing repeatedly will increase thebrightness of the display.CLOSING THE DISPLAY PANELHolding the edge of your display panel, pull it forward until it is flush with the body of your LifeBook notebook. P7010.book  Page 24  Monday, December 20, 2004  1:57 PM
25Getting StartedStarting Your LifeBook NotebookPOWER ONSuspend/Resume/Power On buttonThe Suspend/Resume/Power On button is used to turn on your LifeBook notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion Battery, you can power on your notebook. Figure 3-3 Pressing the suspend/resume/power buttonPress the Suspend/Resume/Power On button that is adjacent to the status indicator panel (Figure 3-3). When you are done working you can either leave your LifeBook notebook in Suspend mode, (See Suspend Mode on page 27 for more information), or you can turn it off. (See Power Off on page 28 for more information)When turn on your LifeBook notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LifeBook notebook will emit an audio warning and/or an error message will be displayed. (See Power On Self Test Messages on page 75 for more information) Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.After satisfactory completion of the Power On Self Test (POST), your notebook will load your operating system.BOOT SEQUENCEThe procedure for starting-up your notebook is termed the Bootup sequence and involves your notebook’s BIOS. When your LifeBook notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook. This information is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your notebook is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.The boot sequence is executed when:■You turn on the power to your LifeBook notebook.■You restart your notebook from the WindowsShut Down dialog box.■The software initiates a system restart. Example:When you install a new application.■You reset the system by pressing the three keys [CTRL+ALT+DEL]. BIOS SETUP UTILITYThe BIOS Setup Utility is a program that sets up the operating environment for your LifeBook notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your notebook.The BIOS Setup Utility configures:■Device control feature parameters, such as changingI/O addresses and boot devices.■System Data Security feature parameters, such as passwords.Entering the BIOS Setup UtilityTo enter the BIOS Setup Utility do the following: 1. Turn on or restart your LifeBook notebook.2. Press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.When you turn on your LifeBook note-book be sure you have a battery installed and charged, or that the AC or Auto/Air-line adapter is connected and has power.Do not carry your LifeBook notebook around with the power on or subject it to shocks or vibration, as you risk damaging your notebook.Status Indicator PanelSuspend/Resume/Power On ButtonNever turn off your LifeBook notebook during the Power On Self Test (POST) or it will cause an error message to be displayed the next time you turn on your LifeBook notebook. (See Power On Self Test Mes-sages on page 75 for more information)P7010.book  Page 25  Monday, December 20, 2004  1:57 PM
26LifeBook P7000 Notebook – Section Three3. Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings.BIOS GuideA guide to your notebook’s BIOS is available online. Please visit our service and support Web site at http://www.computers.us.fujitsu.com/support. Once there, select Support, then select Notebooks under User’s Guides. Select LifeBook BIOS Guides from the pull-down menu for your LifeBook series. If you are unsure of your notebook’s BIOS number, refer to your packing slip.BOOTING THE SYSTEM We strongly recommend that you not attach any external devices and do not put a DVD/CD in your drive until you have gone through the initial power on sequence.When you turn on your LifeBook notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.Designed to accommodate the needs of many users, in many different countries, Windows needs to be config-ured the first time you use them. Windows has three parts: ■Getting Started: You have the opportunity to enter custom information for your configuration file and setup your modem so that your LifeBook notebook will be prepared to dial out. ■Registration: Easy online registration for Windows with Microsoft, and for your LifeBook notebook with Fujitsu. ■Windows License Agreement and Final Settings:You have the opportunity to review the Windows License Agreement.Getting StartedRead the instructions on the screens carefully and fill in the information as directed. You will be asked for such items as the language you wish to use, the country in which you live, your first and last name, and about how you dial out from where you will be using your LifeBook notebook. For the modem settings, enter your current location information where you will be using your Life-Book notebook. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button, and you will go directly to the condition of use page.Once you have set up your LifeBook notebook to dial out, Windows will make a free telephone call to test the settings. If the call is unsuccessful, you will be returned to the phone settings page where you may try to fix them. If you are unable to fix the settings please contact Fujitsu Service and Support. (See Fujitsu Contact Infor-mation on page 1 for more information). If you would simply like to move on, and register at a later time, you may click the Skip button, and you will go directly to the Condition of Use page.Windows RegistrationIf your connection is successful, you will go to a Registration Confirmation page. Enter the requested information, then check the box at the bottom to register your copy of Windows with Microsoft. Once you have finished, click the Next button to continue.Final SettingsThe first part of your final settings is the Windows End User License Agreement. Read the agreement carefully. When you finish reading you must accept or reject the terms of the agreement and then click on the Next button.REGISTERING YOUR LIFEBOOK NOTEBOOKHow do I register my LifeBook notebook?You can register your LifeBook by going to our Web site:us.fujitsu.com/computersYou will need to be set up with an Internet Service Provider (ISP) to use the last option. INSTALLING CLICK ME! The first time you boot up your system, you will see an icon called Click Me! in the Start folder or in the system tray in the bottom right of the screen. When you click the Click Me! icon, your system will automatically build the icon tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access. You may click Cancel at any time within this process to shut down Windows. You may restart this process at any time in the future, but you must complete it in order to use your computer.■If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows or to shut down your LifeBook notebook.■You cannot use your LifeBook notebook until you have accepted the License Agreement. If you stop the process your notebook will return to the beginning of the Windows Welcome Process, even if you shut your notebook down and start it up again.P7010.book  Page 26  Monday, December 20, 2004  1:57 PM
27Getting StartedPower ManagementYour Fujitsu LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your oper-ating conditions, such as those for the display bright-ness. Internal power management for your notebook may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly.For example, you can create an appropriate power saving profile, put your notebook into Suspend mode when itis not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off betweenperformance and power savings.SUSPEND/RESUME/POWER ON BUTTONWhen your LifeBook notebook is active, the Suspend/Resume/Power On button can be used to manually put your notebook into Suspend mode. Push the button when your notebook is active, but not actively accessing anything, and immediately release the button. You will hear two short beeps and your system will enterSuspend mode. (See figure 2-3 on page 6 for location)If your LifeBook notebook is suspended, pushing the Suspend/Resume/Power On button will return your notebook to active operation. You can tell whether or not your system is in Suspend mode by looking at the Power indicator. (See figure 2-3 on page 6) If the indi-cator is visible and not flashing, your notebook is fully operational. If the indicator is both visible and flashing, your notebook is in Suspend mode. If the indicator is not visible at all, the power is off or your notebook is in Hibernation mode.SUSPEND MODESuspend or Standby mode in Windows saves the contents of your LifeBook notebook’s system memory during periods of inactivity by maintaining power to critical parts. This mode will turn off the CPU, the display, the hard drive, and all of the other internal components except those necessary to maintain system memory and allow for restarting. Your notebook can be put in Suspend mode by:■Pressing the Suspend/Resume/Power On button when your system is turned on.■Selecting Standby from the Windows Shut Down menu.■Timing out from lack of activity.■Allowing the battery to reach the Dead BatteryWarning condition.You can change the actions the computer takes when the lid is closed or buttons are pressed by clicking [Start] -> Control Panel. Double-click the Power Options icon and select the Advanced tab. Your LifeBook notebook’s system memory typically stores the file(s) on which you are working, open applica-tion(s) information, and any other data required to support the operation(s) in progress. When you resume operation from Suspend mode, your notebook will return to the point where it left off. You must use the Suspend/Resume/Power On button to resume operation, and there must be an adequate power source available, or your notebook will not resume.HIBERNATION FEATUREThe Hibernation feature saves the contents of yourLifeBook notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. ■If you are running your LifeBook note-book on battery power, be aware that the battery continues to discharge while your notebook is in Suspend mode, though not as fast as when fully opera-tional. ■Disabling the Suspend/Resume/Power On button prevents it from being used to put your LifeBook notebook in Suspend or Hibernation mode. The resume function of the button cannot be disabled.■If your LifeBook notebook is actively accessing information when you enter the Suspend or Hibernation mode, changes to open files are not lost. The files are left open and memory is kept active during Suspend mode or the memory is transferred to the internal hard drive during Hibernation mode.The Suspend or Hibernation mode should not be used with certain PC Cards. Check your PC Card documentation for more information.When PC Cards or external devices are in use, Hibernation mode cannot return to the exact state prior to suspension, because all of the peripheral devices will be re-initialized when the system restarts.P7010.book  Page 27  Monday, December 20, 2004  1:57 PM
28LifeBook P7000 Notebook – Section ThreeEnable or Disable the Hibernation FeatureThe default settings is not enabled. To enable or disable the Hibernation feature follow these easy steps:1. From the Start menu, select Settings, and then select Control Panel.2. From the Control Panel select Power Options.3. Select the Hibernation tab. Select the box to enable or disable this feature.Using the Hibernation Feature1. From the Start menu, select Settings, and then select Control Panel.2. From the Control Panel select Power Options.3. Select the Advanced tab. Select Hibernate from the pull down menu for Power buttons.DISPLAY TIMEOUT The Video Timeout is one of the power management parameters. This feature saves power by turning off the display if there is no keyboard or pointer activity for the user selected timeout period. Any keyboard or pointer activity will cause the display to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. HARD DISK TIMEOUTThe Hard Disk Timeout is another one of the power management parameters. This feature saves power by turning off the hard drive if there is no hard drive activity for the user selected timeout period. Any attempt to access the hard drive will cause it to restart automatically. This feature is independent of the Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. WINDOWS POWER MANAGEMENT Power ManagementThe Power Management icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Management to set the timeout values for turning off the display and hard disks whether you are running the notebook on battery power or one of the adapters. The settings may also be changed in the BIOS. RESTARTING THE SYSTEMIf your system is on and you need to restart it, be sure that you use the following procedure. 1. Click the Start button, and then click Shut Down.2. Select the Restart option from within the Windows Shut Down dialog box.3. Click OK to restart your notebook. Your notebook will shut down and then reboot.POWER OFFBefore turning off the power, check that the Hard Drive, DVD, CD-ROM, CD-RW, PC Card and the Floppy Disk Drive Access indicators are all Off. (See figure 2-3 on page 6) If you turn off the power while accessing a disk or PC Card there is a risk of data loss. To ensure that your notebook shuts down without error, use the Windows shut down procedure.Using the correct procedure to shut down from Windows allows your notebook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:1. Click the Start button, and then click Shut Down.2. Select the Shut Down option from within the Windows Shut Down dialog box.3. Click OK to shut down your notebook.If you are going to store your notebook for a month or more see Care and Maintenance Section. You can also enter Hibernate mode by clicking Start -> Shut Down..., then select-ing Hibernate from the dropdown menu. Turning off your LifeBook notebook with-out exiting Windows or turning on your notebook within 10 seconds of the note-book being shut off may cause an error when you start the next time. Be sure to close all files, exit all applica-tions, and shut down your operating sys-tem prior to turning off the power. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors.P7010.book  Page 28  Monday, December 20, 2004  1:57 PM
294User-Installable FeaturesP7010.book  Page 29  Monday, December 20, 2004  1:57 PM
30LifeBook P7000 Notebook – Section FourP7010.book  Page 30  Monday, December 20, 2004  1:57 PM
31User Installable FeaturesLithium ion BatteryYour LifeBook notebook has a Lithium ion battery (and possibly an optional modular battery) that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals, or other hazards.The Lithium ion battery operating time may become shorter if it is used under the following conditions:■When used at temperatures that exceed a low of 5°C (41°F) or a high of 35°C (95°F). Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The charging indicator on the Status Indicator panel will flash red for the affected battery (battery 1 or 2) when you try to charge a battery that is outside of operating temperature range. (See Battery Charging Indicators on page 12 for more information)■When using a high current device such as a modem, DVD/CD-RW drive, or the hard drive, using the AC adapter will conserve your battery life.RECHARGING THE BATTERIESIf you want to know the condition of the primary Lithium ion battery, check the Battery Level 1 indicator located on the Status Indicator panel. The indicator changes as the battery level changes. If you want to know the condition of the secondary modular Lithium ion battery, check the Battery Level 2 indicator located on the Status Indicator panel. The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LifeBook notebook and connect the AC or Auto/Airline adapter.There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your notebook into Suspend mode, or turn it off while the adapter is charging the battery. (See Power Management on page 27 for more information) Low Battery StateWhen the battery is running low, a low battery notifica-tion message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your notebook will go into Suspend mode. There is no guarantee that your data will be saved once the notebook reaches this point.Do not leave a faulty battery in your LifeBook notebook. It may damage your AC adapter, optional Auto/Airline adapter, another battery or your notebook itself. It may also prevent operation of your notebook by draining all available current into the bad battery.■Battery life will vary based on screen brightness, applications, features, power management settings, battery condition and other customer preferences.DVD, CD-RW, CD-ROM, or hard drive usage may also have a significant impact on battery life. The battery charging capac-ity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one.■Under federal, state, or local law it may be illegal to dispose of batteries by put-ting them in the trash. Take care of our environment by disposing of batteries properly. Check with your local govern-ment authority for information on recy-cling or disposing of old batteries. If you cannot find this information elsewhere, contact your support representative at 1-800-8Fujitsu (1-800-838-5487)Make sure that the Battery Charging indica-tor and the percentage charge is shown inside the Battery Level icon on the Status Indicator Panel. (See Battery Charging Indicators on page 12 for more informa-tion)Using heavy current devices such as Modem or frequent DVD/CD-RW/CD-ROM accesses may prevent charging completely.P7010.book  Page 31  Monday, December 20, 2004  1:57 PM
32LifeBook P7000 Notebook – Section FourDead Battery Suspend mode shows on the Status indi-cator just like the normal Suspend mode. Once your notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Suspend/Resume button to resume operation.In Dead Battery Suspend mode, your data can be main-tained for some time, but if a power source is not provided promptly, the charging indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your notebook while an adapter is charging the battery.Shorted BatteriesThe Status Indicator panel battery charging icons will blink red to indicate a shorted battery or battery problem. This indicates that the battery is damaged and must be replaced so it does not damage any other parts of your LifeBook notebook.REPLACING THE BATTERY With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged.Swapping Batteries when Additional Power Source is not AvailableTo swap batteries in your battery bay when you don’t have another power source available (such as an AC Adapter or charged modular battery), follow these easy steps: (Figure 4-1)1. Have a charged battery ready to install.2. Shut down your notebook.3. Press and hold the battery release latches to open the bay. (Figure 4-1)Figure 4-1  Removing the Battery4. Remove the battery from the bay.5. Place the new battery into the bay. (Figure 4-2)6. Verify that the battery bay latches click into place.Figure 4-2 Installing a batterySwapping Batteries when another Power Source is available To swap batteries in your battery bay when you have an additional power source (such as an AC Adapter or charged modular battery), follow these easy steps: (Figure 4-1)1. Plug in an AC Adapter or install a fully charged modular battery in the Flexible Bay to ensure power is supplied to the system.2. Slide and hold the battery release latches to open the bay.3. Remove the battery from the bay.4. Slide the new battery into the bay.5. Verify that the battery bay latches click into place. ■Once the low battery notification mes-sage appears, you need to save all your active data and put your system into Suspend mode until you can provide a new power source. You should provide a charged battery, AC power adapter, or Auto/Airline adapter as soon as possible.■ When you are in Suspend mode there must always be at least one power source active. If you turn off the power or remove all power sources while your LifeBook notebook is in Suspend mode, any data that has not been saved to the hard drive will be lost.If the Lithium ion battery connector is not fully seated, you may not be able to use your notebook or charge your battery.Battery Release LatchesP7010.book  Page 32  Monday, December 20, 2004  1:57 PM
33User Installable FeaturesFigure 4-3 Loading/Ejecting a 3.5” Floppy DiskExternal Floppy Disk DriveYour LifeBook notebook may have an optional external floppy disk drive which can read and write information on removable 1.44MB and 720KB floppy disks.LOADING A DISKTo load a disk into your disk drive, follow these easy steps: 1. Orient the disk so that its label is facing upwardsand the shutter side is pointing towards the drive. (Figure 4-3)2. Push the disk into the drive until the Eject button pops out and you hear a click. EJECTING A DISKTo eject a disk from the disk drive, follow these easy steps:1. Check that the Floppy Disk Drive Access indicatoris inactive.2. Press the Eject button. This will push your disk partially out of the drive.3. Remove the disk.PREPARING A DISK FOR USEBefore you can use a new disk, it needs to be prepared so your LifeBook notebook knows where to store informa-tion. This preparation is called formatting or initializing a disk. You will need to format new disks, unless they are preformatted. (Please refer to your operating system manual for step-by-step instructions on formatting a disk) To prevent accidental erasure of the data stored on a disk, slide the “write protect” tab until a small hole is exposed. This sets the disk into a protected state where nothing can be added or removed. If you want to add or remove data on a protected disk, slide the “write protect” tab to close the small hole. (Figure 4-4)Figure 4-4 Floppy Disk Write ProtectEject ButtonYour LifeBook notebook is preconfigured to boot from a floppy drive. Reference the BIOS manual for further information on changing the default boot drive.If you eject the disk while the Floppy Disk Drive Access indicator is active, there is a risk of damaging the data on the disk, the disk itself or even the disk drive.Formatting a floppy disk that already con-tains data will erase all of the information on the disk.Write ProtectedWrite EnabledP7010.book  Page 33  Monday, December 20, 2004  1:57 PM
34LifeBook P7000 Notebook – Section FourFigure 4-5 Optical Disk DriveOptical DriveThere is a variety of media available to use with your system, depending upon the system configuration you have selected. Multi-Format DVD Writer and DVD/CD-RW Combo drives are collectively known as “optical drives”.A CD-R or DVD-R disc can only be written to once; CD-RW or DVD-RW discs can be written to over and over. CD-R and CD-RW discs hold up to 700MB of data. DVD-R and DVD-RW discs hold up to 4.7 GB of data. Depending upon the configuration of your LifeBook notebook, you may have one of the following drives:■Multi-Format DVD Writer: The Multi-Format DVD Writer combines seven recordable formats in a single drive (DVD-R, DVD+R, DVD-RW, DVD+RW, DVD-RAM, CD-R, and CD-RW), making it the most versa-tile drive to date.■DVD/CD-RW combo: A DVD/CD-RW combo drive allows you to access movie, software, data, or audio DVD/CDs, and to write data onto recordable CD-R and CD-RW discs.MEDIA PLAYER SOFTWAREMulti-Format DVD Writer model only: With the Multi-Format DVD Writer and media player software you can play DVD movies and music CDs on your LifeBook notebook. The media player includes controls which allow you to take full advantage of the features of a DVD movie, as well as standard features such as fast forward, fast reverse, pause, etc. With this drive you can also burn onto recordable DVD-R/RW, DVD+R/RW, or CD-R/RW discs. DVD/CD-RW Combo model only: With the combo drive, you can play DVD movies, read audio CDs, and write data onto recordable CD-R or CD-RW discs.LOADING A DVD OR CDTo load a disc into your optical drive, follow these steps (Figure 4-6):1. Push and release the eject button on the front of the optical drive to open the holder tray. The tray will come out of the notebook a short distance. 2. Gently pull the tray out until a media disc can easily be placed in the tray.3. Place the media disc into the tray, label side up. Snap the hole in the center of the disc onto the raised circle in the center of the tray.4. Gently push the holder tray back in until you hear a click. Media Holder TrayMedia Eject ButtonInstall your media player software before first using the optical drive. Refer to the applicable readme file on the Driver Applications CD-ROM.The Multi-Format DVD Writer also supports burning and reading of DVD-RAM. (Windows XP supports burning and reading of DVD-RAM as a standard feature.)There may be a protective sheet in the tray from when it was shipped; make sure it is removed before operating the drive, other-wise you may damage the drive.If you have disabled the Auto Insert Notifi-cation Function, you will have to start the drive from your desktop, since your note-book will not automatically recognize that media has been loaded.P7010.book  Page 34  Monday, December 20, 2004  1:57 PM
35User Installable FeaturesFigure 4-6  Loading/Removing MediaREMOVING MEDIA1. Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the notebook a short distance.2. Gently pull the tray out until the disc can easily be removed from the tray.3. Carefully remove the media disc from the holder tray.4. Gently push the holder tray back in until you hear a click.USING THE OPTICAL DRIVE SOFTWAREStarting a DVD Movie 1. Insert the DVD movie into the optical drive of your notebook. If the CD AutoRun feature activates, skip Step 2. 2. The first time you insert a movie into the media tray, you will be prompted to select what you want the system to do when discs are inserted (i.e., start auto-matically or wait for a prompt). Until you make a selection, you will receive the same prompt when-ever you insert a disc. Opening the Optical Drive Control PanelWith most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the optical drive control panel and the mouse.1.  Right-click on the movie screen to open a dropdown menu for options.2. Select View, then Player for all the controls available. This will open the control panel into the bottom of the screen.Using the Optical Drive Control PanelThe optical drive software allows you to watch the movie much like a VCR player. You have the option to pause, rewind, fast-forward and stop the movie at any point.1.  To Pause the movie, click the button.2.  To Rewind the movie, click the  button to rewind to a specific portion of the movie, or the  button to return to the opening screen.3.  To Fast-forward the movie, click the  button to forward to a specific portion of the movie, or the button to jump to the ending credits.4.  To Stop the movie, click the  button.Exiting the DVD/CD-RW Application1. Click the U located in the upper right corner of the title bar. This will open an optical drive dialog box.2.  Click Yes to stop and exit the movie, or No to close the optical drive dialog box and return to the movie.USING DOLBYTM HEADPHONEThe Dolby Headphone utility lets you enjoy multi-channel sound sources, such as movies, with realistic surround sound using your conventional stereo head-phones.Dolby Headphone is a signal processing system that enables your stereo headphones to realistically portray the sound of a five-speaker playback system.To use the Dolby Headphone feature, perform the following steps:1. Double click the InterVideo WinDVD icon on your desktop.2.  On the toolbar that appears, click the Fujitsu logo3. Select the desired Room Filter Setting.4. Click OK. The Dolby Headphone feature will now be enabled until you disable it selecting Disable in the Dolby Headphones menu (click on the Fujitsu logo to open it). Note that Dolby Headphone is not accessible if a DVD is not inserted.(c)(a)(d)(b)■Media discs which do not have the Dolby Surround 5:1 symbol will not support Dolby Headphone.■After making changes to the Dolby Headphone feature and clicking OK, wait at least ten seconds before making another change in order to allow the system to stabilize.P7010.book  Page 35  Monday, December 20, 2004  1:57 PM
36LifeBook P7000 Notebook – Section FourUSING THE OPTICAL DRIVE ON BATTERY POWERSince an optical drive consumes a lot of power, your overall battery life will be shorter when operating the drive continuously (such as watching a DVD movie) than during standard operation. Many movies run-times are longer than your LifeBook notebook can support on a single battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to view it in its entirety. To Watch a Movie on Battery Power:1. Have an additional full-charged battery or your AC adapter ready for use.2. Start watching your DVD movie. 3. When the low battery warning occurs, immediately stop the movie and exit the DVD/CD-RW application. 4. Connect an AC Adapter to your system, or install a fully charged battery in the Flexible Bay (after removing any modular devices that may be present in the bay) prior to removing the main battery. 5.  Manually place your notebook into suspend mode by depressing the Suspend button then replace the discharged battery with a fully-charged battery. 6. If you removed the optical drive from the Flexible Bay in step 4, reinstall it now.7.  Resume your notebook by pressing the Suspend button again. This step is not required if you attached AC power without entering suspend mode.8.  Restart your DVD/CD-RW application and skip to the chapter of the movie you were last watching.9.  Continue watching your DVD movie.AUTO INSERT NOTIFICATION FUNCTIONThe Auto Insert Notification function allows your Life-Book notebook to automatically start a DVD/CD as soon as it is inserted in the optical drive and the tray is closed. Your notebook will begin playing an audio DVD/CD or will start an application if the DVD/CD includes an auto run file.To prevent a CD from playing automatically as soon as it is inserted, refer to the related help file for your specific operating system.EMERGENCY TRAY RELEASEIn the event that your system does not have power applied, you can still open the media tray using the end of an opened paper clip. To open the tray, insert the paper clip into the emergency tray release hole on the fact of the tray (Figure 4-7). The tray will pop open.Figure 4-7 Using the Emergency Tray Release■Prolonged use of the optical drive, such as when watching a DVD movie, will substantially reduce your note-book’s battery life.■An additional fully-charged battery is highly recommended if you will be watching DVD movies on battery power. If you don’t have an additional battery, you may purchase one either on-line at us.fujitsu.com/computers or call 1-877-372-3473.If you do not stop the optical drive quickly and the LifeBook notebook attempts to auto-suspend (critical battery low state) the notebook will shut down improperly. If this occurs, you will need to install a fresh power source (either a charged battery or AC Adapter).Some shorter DVD movies may not require you to swap batteries or attach AC power to complete them. However, it is best to be prepared since actual battery life while operating the optical drive cannot be guaranteed.P7010.book  Page 36  Monday, December 20, 2004  1:57 PM
37User Installable FeaturesFigure 4-8 Installing/Removing PC CardsPC CardsYour Fujitsu LifeBook notebook supports Type I and II PC Cards, which can perform a variety of functions. Some available PC Cards:■Fax/data modem cards■Local area network (LAN) cards■IDE solid-state disk cards■SCSI cards■Wireless LAN cards ■Other PC Cards that conform to PCMCIA 2.1 or CardBus standardsFor further information, refer to the instructions supplied with your PC Card.INSTALLING PC CARDSPC Cards are installed in the PC Card slot. To install aPC Card, follow these easy steps: (Figure 4-8) 1. See your PC Card manual for specific instructions on the installation of your card. Some PC Cards may require your notebook to be Off while installing them.2. Make sure there is no PC Card currently in the slot. If there is, see Removing PC Cards.3. Insert your PC Card into the slot, with the product label facing up. 4. Push the card into the slot firmly until it is seatedin the opening. You will hear a click and the Eject button will pop away from your notebook.REMOVING PC CARDSTo remove a PC Card, follow these easy steps:1. See your PC Card manual for specific instructions on removing your card. Some PC Cards may require your notebook to be in Suspend Mode or Off while removing them.2. Push the Eject button in until it is flush with the notebook. This will push the PC Card slightly out of the slot allowing you to remove the card.Eject ButtonPC Card SlotPC Card■Installing or removing a PC Card during your LifeBook notebook’s shutdown or bootup process may damage the card and/or your notebook.■Do not insert a PC Card into a slot if there is water or any other substance on the card as you may permanently dam-age the card, your LifeBook notebook, or both.Windows has a shutdown procedure for PC Cards that must be followed before removing a card. (Please review your oper-ating system manual for the correct proce-dure). If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applica-tions and shut down your notebook. If the PC Card has an external connector and cable, do not pull the cable when removing the card.P7010.book  Page 37  Monday, December 20, 2004  1:57 PM
38LifeBook P7000 Notebook – Section FourFigure 4-9 Installing/Removing CF CardsCompact Flash CardsYour Fujitsu LifeBook notebook supports Compact Flash (CF) cards, which can perform a variety of func-tions. Some available CF Cards:■Memory cards■Fax/data modem cards■Local area network (LAN) cards■Wireless LAN (802.11b) cardsFor further information, refer to the instructions supplied with your CF Card.INSTALLING CF CARDSCF Cards are installed in the CF Card slot. To install aCF Card, follow these steps: (Figure 4-9) 1. See your CF Card manual for specific instructions on the installation of your card. Some CF Cards may require your notebook to be Off while installing them.2. When you receive your LifeBook, there will be a protective plug installed in the slot. Whenever you don’t have a CF Card installed, be sure to replace the plug to prevent system contamination. To remove the plug, press the CF Card eject button. (Figure 4-10)Figure 4-10 Removing CF Slot plug3. When the CF Slot plug is ejected, remove it from the slot.4. Insert your CF Card into the slot, with the product label facing up. Figure 4-11 Installing a CF Card5. Push the card into the slot firmly until it is seatedin the opening. You will hear a click and the Eject button will pop away from your notebook.Eject ButtonCF Card SlotCF Card■Installing or removing a CF Card during your LifeBook notebook’s shutdown or bootup process may damage the card and/or your notebook.■Do not insert a CF Card into a slot if there is water or any other substance on the card as you may permanently dam-age the card, your LifeBook notebook, or both.CF Slot PlugCF Eject ButtonP7010.book  Page 38  Monday, December 20, 2004  1:57 PM
39User Installable FeaturesREMOVING CF CARDSTo remove a CF Card, follow these easy steps:1. See your CF Card manual for specific instructions on removing your card. Some CF Cards may require your notebook to be in Suspend Mode or Off while removing them.2. Push the Eject button in until it is flush with the notebook. This will push the CF Card slightly out of the slot allowing you to remove the card.Figure 4-12 Removing a CF CardWindows has a shutdown procedure for CF Cards that must be followed before removing a card. (Please review your operating system manual for the correct procedure). If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applica-tions and shut down your notebook. P7010.book  Page 39  Monday, December 20, 2004  1:57 PM
40LifeBook P7000 Notebook – Section FourFigure 4-13. Installing a Memory Stick/SD CardMemory Stick/Secure Digital SlotYour LifeBook notebook supports the following memory cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data. ■SD Memory Card■Memory Stick Media■Memory Stick Select Media■Memory Stick Duo Media■Memory Stick PRO MediaMemory Stick is a flash memory technology developed by Sony Electronics. Memory Stick allows you to record, transfer and share digital content, such as digital pictures, movies, music, voice, and computer data and applications.Secure Digital (SD) Cards are very similar to Memory Sticks, but they are shorter. Like the Memory Stick, SD Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. SD Cards transfer data quickly, with low battery consumption. Like the memory stick, it uses flash memory architecture.Figure 4-14. Memory Stick and Secure Digital CardINSTALLING MEMORY STICK/SD CARDSMemory Sticks and SD Cards are installed in the Memory Stick/SD Card slot (Figure 4-13). To install aMemory Stick or SD Card, follow these steps: 1. See your Memory Stick or SD Card manual for instructions on the installation of your card. Some cards may require that your notebook is off while installing them.2. Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD Card.Note: A Memory Stick is usedfor illustration purposes. Memory Stick/SD Card SlotMemory Stick• Some of the media in the above list may have more features than others.• An adapter is required for Memory Stick Duo.• Copyright Protection Technology can-not be used.• MultiMedia Cards (MMC) and Secure MMC are not supported.■Installing or removing a Memory Stick or SD Card during your LifeBook note-book’s shutdown or bootup process may damage the card and/or your LifeBook notebook.■Do not insert a card into a slot if there is water or any other substance on the card as you may permanently damage the card, your LifeBook notebook, or both.P7010.book  Page 40  Monday, December 20, 2004  1:57 PM
41Memory Stick/SD Card3. Insert your PC Card into the slot with the product label facing up.4. Push the card firmly into the slot until it is seated in the connector. REMOVING A MEMORY STICK/SD CARDTo remove a Memory Stick or SD Card, follow these easy steps:Push the Memory Stick or SD Card in until it unlatches. It will then eject from the slot for removal.See your Memory Stick or SD Card manual for specific instructions on the removal of your card. Some cards may require your LifeBook notebook to be in Suspend Mode or Off while removing them.P7010.book  Page 41  Monday, December 20, 2004  1:57 PM
42LifeBook P7000 Notebook – Section FourMemory Upgrade ModuleYour LifeBook notebook can be upgraded to include up to 1 GB of in-slot high speed Double Data Rate (DDR) Synchronous Dynamic RAM (SDRAM). To increase your LifeBook notebook’s memory capacity, you may install a larger memory upgrade module. Your LifeBook notebook has two micro DIMM slots. If you have less than 1 GB pre-installed, and you would like to increase it, you will need to remove the installed module and replace it with the larger module or add a new module to an empty slot. The memory upgrade must be a dual-in-line (micro DIMM) SDRAM module. To ensure 100% compatibility, purchase the memory module only from the Fujitsu web store at us.fujitsu.com/computers.ACCESSING THE MEMORY COMPARTMENTTo gain access to the memory compartment, follow these steps:1. Turn off power to your LifeBook notebook, and remove any power adapter (AC or auto/airline), battery pack, and modem connection.2. Place your LifeBook notebook with the bottom facing up on a clean work surface.3. Remove the two screws from the holes in the memory compartment cover. (Figure 4-15) Figure 4-15. Removing screws from memory compartment coverREMOVING A MEMORY MODULE1. Perform steps 1 through 3 of Accessing the Memory Compartment.2. Pull the module clips sideways away from each side of the memory module simultaneously. (Figure 4-16)Figure 4-16. Removing a memory module3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the back of your LifeBook notebook. 4. Store the memory upgrade module in a static guarded sleeve.5. Install a new memory module as detailed in the procedure below.6. Replace the memory compartment cover.INSTALLING A MEMORY MODULE1.   Align the connector edge of the memory upgrade module, chip side up, with the connector slot in the compartment. (Figure 4-17)Figure 4-17. Installing a memory module2 . Insert the memory upgrade module at a 45o angle and press it firmly onto the connector.3. Press the memory upgrade module down into the compartment until it locks underneath the retaining clip. You will hear a click when it is properly in place. (Figure 4-17)The memory upgrade module can be severely damaged by electrostatic dis-charge (ESD). Be sure you are properly grounded when handling and installing the module.You must turn off power and remove any modem connection before installing the memory upgrade module.There is already a memory module pre-installed when you receive your system. In order to increase the memory, you must first remove the old memory chip.Module ClipP7010.book  Page 42  Monday, December 20, 2004  1:57 PM
43User Installable FeaturesCHECKING THE MEMORY CAPACITYOnce you have changed the system memory capacity by replacing the installed module with a larger one, be sure to check that your notebook has recognized the change.Check the memory capacity by clicking [Start] -> Settings -> Control Panel, then double-clicking the System icon. Select the General tab and check the amount of memory under “Computer:”.There may be a variation between the actual memory size and what is displayed. This is due to the fact that your system uses a video graphics chip which dynami-cally allocates system memory to accelerate graphics performance. Up to 64 MB of memory is dynamically shared on an as-needed basis using Dynamic Video Memory Technology (DVMT).The memory upgrade module is not something you routinely remove from your LifeBook notebook. Once it is installed, you should leave it in place unless you want to increase system memory capacity.If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. (If the module is properly installed and the capacity is still not correctly recognized, see Trouble-shooting on page 67.P7010.book  Page 43  Monday, December 20, 2004  1:57 PM
44LifeBook P7000 Notebook – Section FourDevice PortsYour Fujitsu LifeBook notebook comes equipped with multiple ports to which you can connect external devices such as disk drives, keyboards, printers, etc. MODEM (RJ-11) TELEPHONE PORTThe modem (RJ-11) telephone port is used for an internal modem. To connect the telephone cable follow these easy steps: 1. Align the connector with the port opening (Figure 4-18).2. Push the connector into the port until it is seated.3. Plug the other end of the telephone cable into a tele-phone outlet.Figure 4-18 Modem PortFigure 4-19 Connecting the ModemThe modem sound is deactivated by default, to activate modem sound follow these easy steps:1. Right click on the Speaker icon in your system tray.2. Select Open Volume.3. Select Option/Properties.4. Under “Show the following volume controls”, click on Phone and click OK.5. Uncheck the Mute box under Phone Balance.INTERNAL LAN (RJ-45) PORT The internal LAN (RJ-45) port is used for an internalFast Ethernet (10/100 Base-T/Tx) connection. If your notebook has been configured with internal LANcapability you will need to configure your notebookto work with your particular network. (Please refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these easy steps: 1. Open the protective cover on the right side of the system (Figure 4-20).2. Align the connector with the port opening.3. Push the connector into the port until it is seated.4. Plug the other end of the cable into a LAN outlet.Figure 4-20 LAN PortThe internal modem is not intended for use with Digital PBX systems. Do not con-nect the internal modem to a Digital PBX as it may cause serious damage to the internal modem or your entire LifeBook notebook. Consult your PBX manufac-turer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem.■The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connec-tion rate depends on the line conditions. The maximum speed is 33600bps at upload. ■The internal modem on all Fujitsu Life-Book notebooks are registered for use in the United States and Canada. The modem may be certified in other coun-tries.P7010.book  Page 44  Monday, December 20, 2004  1:57 PM
45User Installable FeaturesIEEE 1394 PORTThe IEEE 1394 port (also known as “Firewire” or “iLink”) allows you to connect devices that are compliant with IEEE standard 1394. This port is effec-tively a very fast communications port. Some digital devices - such as digital cameras - use IEEE 1394 ports for fast transfer of digital files and data.In order to connect an IEEE 1394 device, follow these steps: 1. Open the protective cover on the right side of the system (Figure 4-21).2. Align the connector with the port opening.3. Push the connector into the port until it is seated.Figure 4-21 IEEE 1394 PortS-VIDEO OUT PORT (TV OUT)The S-Video port allows you to connect and use directly any S-Video device, such as a VCR or television. The S-Video standard provides for a higher quality picture than NTSC or PAL. In order to connect an S-Video device, follow these easy steps: Figure 4-22 S-Video Out Port1. Open the protective cover on the right side of the system (Figure 4-22).2. Align the connector with the port opening. 3. Push the connector into the port until it is seated.UNIVERSAL SERIAL BUS PORTSThe Universal Serial Bus 2.0 ports allow you to connect USB devices such as external game pads, pointing devices, keyboards and/or speakers. USB 2.0 is much faster than USB 1.1 (Its 480Mbps transfer rate is 40 times faster than that of USB 1.1). USB 2.0 ports are backward-compatible to work with USB 1.1 devices. In order to connect a USB device follow these easy steps: 1. Align the connector with the port opening.2. Push the connector into the port until it is seated.Figure 4-23 USB PortsHEADPHONE JACKThe headphone allows you to connect headphones or powered external speakers to your notebook. Your head-phones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: 1. Align the connector with the port opening.Figure 4-24 Headphone/Optical Digital Audio Out Jack2. Push the connector into the port until it is seated.The headphone and optical digital audio out share the same jack.If you plug headphones into the head-phone jack, the built-in stereo speakers will be disabled.USB PortUSB PortHeadphone/Optical Digital Audio Out JackP7010.book  Page 45  Monday, December 20, 2004  1:57 PM
46LifeBook P7000 Notebook – Section FourOPTICAL DIGITAL AUDIO CONNECTORThe optical digital audio-out connector allows you todownload digital audio to MiniDisc recorders. It uses SPDIF (Sony Philips Digital Interface) format. Use the following setting when using the digital audio-out connector. 1. Connect the MiniDisc recorder or external speaker to the Optical Digital Audio-Out Connector. (Figure 4-24)2. Insert the disk you want to play in the DVD/CD-RW tray.3. Click on Start -> Programs -> InterVideo WinDVD. (In Windows XP systems, you can go directly from Start to InterVideo WinDVD.)4. When the WinDVD interface appears, right-click in the WinDVD window and select [Setup] from the menu.5. Click on the Audio tab and select Enable S/PDIF output.6. Click [Apply].MICROPHONE JACKThe microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your notebook. In order to connect a microphone follow these easy steps: Figure 4-25 Microphone jack1. Align the connector with the port opening (Figure 4-25).2. Push the connector into the port until it is seated.EXTERNAL MONITOR PORTThe external monitor port allows you to connect an external monitor. In order to connect a monitor follow these easy steps: 1. Open the protective cover on the right side of the system (Figure 4-26).2. Align the connector with the port opening.3. Push the connector into the port until it is seated. Figure 4-26 Installing the External Monitor Cable■When headphones or a SPDIF cable is installed, the speakers are disabled.■Before using the SPDIF function, make sure that WinDVD software is installed on your system.■Certain older CDs and DVDs will not work in conjunction with the SPDIF con-nector.■The frequency of the digital sound output from the SPDIF output connector is fixed to 48KHz. If a sampling rate convertor is not installed in your connecting digital electronic device (e.g., MD player), recording is not possible. Please see the user manuals for the electronic devices for further details.■The sound recorded through connecting a digital electronic device (e.g., MD player) to the SPDIF output connector cannot be used as digital output. All output data from the SPDIF output connector has copyright protection information included.■Please be careful, as there are several types of cables for connecting a digital electronic device (e.g., MD player) to the digital audio-out connector, depend-ing on the connector type. The connec-tor on your computer is an Optical Mini Plug (3.5mm diameter mini plug)Pressing the [Fn] + [F10] keys allows you to change your selection of where to send your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external monitor only, finally moving to both the built-in display panel and an external monitor.Microphone JackP7010.book  Page 46  Monday, December 20, 2004  1:57 PM
475Using the Integrated Wireless LANP7010.book  Page 47  Monday, December 20, 2004  1:57 PM
48LifeBook P7000 Notebook – Section FIveP7010.book  Page 48  Monday, December 20, 2004  1:57 PM
49Wireless LAN User’s Guide  FCC REGULATORY INFORMATIONPlease note the following regulatory information related to the wireless LAN device.Regulatory Notes and StatementsWireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wire-less LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:On board an airplane, orIn an explosive environment, orIn situations where the interference risk to other devices or services is perceived or identified as harmful.In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment.Regulatory Information/DisclaimersInstallation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its autho-rized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operating in conjunction with any other antenna or transmitter.Federal Communications Commission statementThis device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.FCC Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the distance between the equipment and the receiver.3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.4. Consult the dealer or an experienced radio/TV technician for help.FCC Radio Frequency Exposure statementThe maximum SAR value measured from the devices are:Export restrictionsThis product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment.Canadian NoticeTo prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. High power radars are allocated as primary users of 5250-5350 MHz and 5650 - 5850 MHz and these radars could cause inter-ference and/or damage to LELAN (license-exempt LAN) devices operating in these bands.T Series.book  Page 95  Wednesday, February 16, 2005  1:59 PMFor Atheros and Intel PRO Set Wireless LAN:In accroding with 47 CFR Part15.407(e) U-NII devices operating5.15 - 5.25GHz frequency bands are restricted to indoor operations only.The available  scientific evidence does not show that anyhealth problems are associated with using low power wireless devices. There is no proof, however, that theselow power wilreless devices are absolutely safe. Low powerWireless devices emit low levels of radio frequency energy(RF) in the microwave range while being used. Whereas highlevel of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heatingeffects causes no known adverse health effects. Many studiesof low-level RF exposure have not found any biological effects, Some studies have suggested that some biological effectsmight occur, but such findings have not been confirmed by additional research. This wireless LAN radio device has beentested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meetsthe FCC radio frequency (RF) Exposure Guidelines inSupplement C to OET65. 2.4GHz-band : 0.216[W/kg],5.25GHz-band : 1.05[W/kg],5.8GHz-band : 0.546{W/kg] at Body
50LifeBook P7000 Series Notebook - Section FiveBefore Using the Wireless LANThis manual describes the procedures required to prop-erly setup and configure the integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference.Wireless LAN Devices Covered by this DocumentThis document is applicable to systems containing one of the following three devices. Most of the procedures are identical. Sections that differ between the devices have been noted in the text:■Intel PRO/Wireless 2200BG Network Connections (802.11b/g): Available on LifeBook P7010 notebook model■Intel PRO/Wireless 2915ABG Network Connections (802.11a+b/g): Available on LifeBook P7010 notebook model■Atheros AR5002X Mini-PCI wireless network card (802.11a + b/g): Available on LifeBook P7010D note-book modelCharacteristics of the WLAN Device■The WLAN device is a Mini-PCI card attached to the main board of the mobile computer. ■The WLAN devices operate in license-free RF bands, therefore eliminating the need to procure an FCC license to operate. All three WLAN devices operate in the 2.4GHz Industrial, Scientific, and Medical (ISM) RF band. Additionally, the Intel PRO/Wireless 2915ABG and Atheros AR5002X devices operate in the lower and middle bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands. ■The Intel PRO/Wireless 2200BG WLAN device is capable of two operating modes, IEEE802.11b and IEEE802.11g. The Intel PRO/Wireless 2915ABG and Atheros AR5002X WLAN devices are capable of three operating modes, IEEE802.11a, IEEE802.11b and IEEE802.11g. ■Encoding of data is modulated using Direct Sequence Spread Spectrum (DSSS) and Complementary Code Keying (CCK) when the WLAN device is operating in IEEE 802.11b mode and Orthogonal Frequency Divi-sion Multiplexing (OFDM) when operating in IEEE802.11a or IEEE802.11g mode. ■The WLAN device is Wi-Fi certified and operates at the maximum data transfer rate of 54 Mbps in IEEE802.11a or IEEE802.11g mode and 11 Mbps in IEEE802.11b mode.■The maximum communication range indoors is approximately 80 feet (25 meters).   However, that range will increase or decrease depending on factors such as number of walls, reflective material, or inter-ference from external RF sources.■The WLAN device supports the following encryption methods - WEP, CKIP, TKIP, and AES encryption.WIRELESS LAN MODES USING THIS DEVICEAd Hoc Mode (See Figure 5-1)"Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks Figure 5-1. Ad Hoc Mode NetworkP7010.book  Page 50  Monday, December 20, 2004  1:57 PM
51WIreless LAN User’s Guide are an easy and inexpensive method for establishing network connectivity between multiple computers.Ad Hoc mode requires that the SSID, network authenti-cation, and encryption key settings are identically configured on all computers in the Ad Hoc network. Access Point (Infrastructure) Mode (See Figure 5-2)Infrastructure mode refers to a wireless network archi-tecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or can communicate with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the wired LAN in order to access computers, devices, and services such as file servers, printers, and databases.How to Handle This DeviceThe WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Oper-ating System that your mobile computer comes with has been pre-configured to support the WLAN device. WIRELESS NETWORK CONSIDERATIONS■The Intel PRO/Wireless 2200BG WLAN device sup-ports IEEE802.11b and IEEE802.11g. The Intel PRO/Wireless 2915ABG and Atheros AR5002X WLAN devices support IEEE802.11a, IEEE802.11b and IEEE802.11g.■The Intel PRO/Wireless 2200BG WLAN device oper-ates in the 2.4GHz ISM band. The Intel PRO/Wireless 2915ABG and Atheros AR5002X WLAN devices oper-ate in the 2.4GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.■The maximum range of the WLAN device indoors is typically 80 feet (25 meters). Please note that the max-imum range you achieve may be shorter or longer than 80 feet, depending on factors such as access point transmit power, number and density of obstructions, or external RF interference.■Microwave ovens will interfere with the operation of WLAN device as microwave ovens operate in the same 2.4GHz frequency range that IEEE802.11b/g devices operate in. Interference by microwaves does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.■Wireless devices that transmit in the 2.4GHz fre-quency range may interfere with the operation of WLAN devices in IEEE802.11b/g modes. Symptoms of interference include reduced throughput, intermittent disconnects, and large amounts of frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure the proper operation of the WLAN device.Figure 5-2. Access Point (Infrastructure) Mode NetworkADSL modem,cable modem,or similarInternetWired LANAccess Point*Wireless LAN*An optional hub for a wiredLAN may be required dependingupon the type of access point used.P7010.book  Page 51  Monday, December 20, 2004  1:57 PM
52LifeBook P7000 Series Notebook - Section FiveDEACTIVATING THE WLAN DEVICEDeactivation of the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). Fujitsu mobile computers employ two methods with which to deactivate the WLAN device:■Using the Wireless On/Off Switch■In Windows, using the Intel PROSet Software or Atheros Client Utility software.Deactivation using the Wireless On/Off SwitchThe WLAN device can be deactivated quickly and effi-ciently by toggling the Wireless On/Off Switch to the Off position. (Figure 5-3)The Wireless On/Off switch has no effect on non-Wire-less LAN models.Figure 5-3. Wireless LAN On/Off Switch LocationDeactivation using the Intel PROSet SoftwareThe WLAN device can also be deactivated in Windows using the Intel PROSet Software. The procedure to accomplish this:1. Click [Start]-> [All Programs].2. Select Intel ProSet Wireless, then click on Intel ProSet Wireless from the menu that appears. The Intel ProSet Wireless utility will be displayed.3. At the bottom left corner of the window, select Wireless Off from the dropdown list.Deactivation using Atheros Client Utility software1. Right-click on Atheros Client Utility icon in the system tray. Select “Open Atheros Client Utility” from the menu.2. Choose Action and click Disable Radio.ACTIVATING THE WLAN DEVICEActivation of the WLAN device can be accomplished using the same methods as the deactivation process■Using the Wireless On/Off Switch■In Windows using the Intel PROSet Software or Atheros SoftwareWireless LANOn/Off SwitchOnOffP7010.book  Page 52  Monday, December 20, 2004  1:57 PM
53WIreless LAN User’s Guide Configuration of the WLAN DeviceThe WLAN Device can be configured to establish wire-less network connectivity using one of the following tools:■Intel PROSet Software - The Intel PROSet Software allows for multiple profile setup and supports auto-matic profile switching. Support for most industry standard security solutions is contained in this soft-ware.■Atheros Client Utility - The Atheros Client Utility soft-ware allows for multiple profile setups and supports automatic profile switching. Support for most indus-try standard security solutions is contained in this software.FLOW OF OPERATIONS1. Activate the WLAN Device (See Activating the WLAN Device on page 52 for more information).2. Configure the Wireless Network parameters (See Configure Wireless Network Parameters on page 53 for more information).■Enter the network name (SSID)■Choose the appropriate WLAN architecture (Ad Hoc or Infrastructure)■Choose Authentication method: Open, Shared, WPA-Enterprise, WPA2-Enterprise, WPA-Personal, or WPA2-Personal■If using static WEP keys, enter static WEP key and choose key index. 3. Configure network settings (See Configure Net-work Parameters on page 53 for more information)■TCP/IP settings■Workgroup or Domain settings.CONFIGURATION USING INTEL PROSET SOFTWAREThis section explains the procedure to properly configure the WLAN device using the Intel PROSet Soft-ware. Pre-defined parameters will be required for this procedure. Please consult with your network adminis-trator for these parameters:Network Name - Also known as the SSIDNetwork Key (WEP) - Required if using static WEP keys. Authentication Type - Open, Shared, WPA, or WPA-PSKProcedure1. Activate the WLAN device using either the Wireless On/Off Switch or the Intel PROSet software.2. Click the [Start] button first and then [All Pro-grams].3. Click the icon [Intel PROSet Wireless] to execute the Intel PROSet Wireless software.4. Click the [Add] button. The General Settings dialog displays. 5. Enter a profile name in the Profile Name field. 6. Enter the network SSID, in the Network Name (SSID) field. 7. Click Infrastructure or Ad Hoc for the operating mode. 8. Click [Advanced].9. The Mandatory Access Point option is only used if Infrastructure mode is selected. Use this option to connect to a specific access point. Enter the MAC address for the access point. Click OK to save the setting and return to the General Settings page. 10. Click [Next].11. If you are using Cisco CCX, click Cisco Options to enable Cisco CKIP data encryption on the Security Settings page. Check the Cisco Compatible Exten-sions Options. If you have checked the Cisco's "Mixed-Cell" box in the Advanced Setting, this option must also be checked.12. Click [OK].13. Click Next.14. Select Open, Shared, WPA-Enterprise, WPA2-Enterprise, WPA-Personal, or WPA2-Personal in the Network Authentication options. 15. Select either None, WEP, CKIP (if Enable Cisco Cli-ent eXtentions is enabled, use CKIP or WEP), or TKIP for the data encryption. 16. If WEP is selected, select either 64 or 128-bit for the Encryption Level. 17. Select the key index 1, 2, 3 or 4. 18. Enter the WEP key if required. If your network does not employ a 802.1x/EAP security mechanism, please skip to step 24.P7010.book  Page 53  Monday, December 20, 2004  1:57 PM
54LifeBook P7000 Series Notebook - Section Five19. Click the Enable 802.1x checkbox to enable the 802.1x security option. Please contact your network administrator if configuration of this setting is required.20. Select the appropriate Authentication Type. Please contact your network administrator if configura-tion of this setting is required.21. After selecting your authentication type, enter the user name, domain, and password of the user you have created on the authentication server. The user name and password do not have to be the same as name and password of your current Windows user login.22. Click [OK] to save the settings.23. From the Intel ProSet Wireless page, click the new profile name shown in the Profile List. Use the up and down arrows to position the priority of the new profile in the priority list. 24. Click the Connect button to connect to the net-work. 25. Click [Close] if you want to close the Intel(R) PROSet for Wireless window.CONFIGURATION USING ATHEROS CLIENT UTILITY SOFTWAREThis section explains the procedure to properly configure the WLAN device using the Atheros Client Utility. Pre-defined parameters will be required for this procedure. Please consult with your network adminis-trator for these parameters:Network Name - Also known as the SSIDNetwork Key (WEP) - Required if using static WEP keys. Authentication Type - Open, Shared, WPA, or WPA-PSKProcedure1. Activate the WLAN device using either the Wireless On/Off Switch or the Atheros Client Utility2. Right-click on the “Atheros Client Utility” icon in the system tray, and select “Open Atheros Client Utility” from the menu.3. From the Current Status page, click the Profile Management tab. 4. If this is your first time using this utility, highlight the profile [Default] and Click the [Modify] button, otherwise Click the [New] button. The General Set-tings dialog displays. 5. From the General page, enter a profile name in the Profile Name field. 6. Enter the network SSID, in the SSID1 field. If you wish to create a profile that can connect to up to 3 different wireless networks, SSID's can be entered in the SSID2 and SSID3 fields as well.7. Click the Security tab. 8. The Security tab allows for the configuration of the Security modes listed in the table below. Please select the radio button of the desired security mode.   If these settings are not known to you, please consult with your network administrator for the correct settings. 9. Click OK10. Click the Advanced tab11. The Advanced tab allows for the configuration of the options detailed in the table below.Field Name DescriptionWPA Enables the use of Wi-Fi Protected Access. Choosing WPA opens the WPA EAP drop-down menu. Options include TLS and PEAP. If these settings are not known to you, please consult with your network administrator for the correct settings. WPA-PSK Enables WPA-Pre-Shared Key. Click on the Configure button to enter the WPA Passphrase. If these settings are not known to you, please consult with your network administrator for the correct settings. 802.1x Enables 802.1x security. If these settings are not known to you, please consult with your network administrator for the correct settings. Choosing this option opens the 802.1x EAP type drop-down menu. Options include TLS, PEAP, and LEAPPre-Shared Key Enables the use of pre-shared keys that are defined on both the access point and the station. This is where static WEP keys are entered. Click the Configure button to fill in the Define Pre-Shared Keys window.None No securityP7010.book  Page 54  Monday, December 20, 2004  1:57 PM
55WIreless LAN User’s Guide .12. Click OK13. If the profile you just created does not activate immediately, click the Profile Management tab, highlight the desired Profile, and click Activate.14. Click [Close] if you want to close the Atheros Client Utility.CONNECTION TO THE NETWORKThis section explains connection to the network.If there is an administrator of the network, contact the network administrator for data settings.Setting the networkPerform the “Setting TCP/IP” and “Confirming the computer and work group names” operations required for network connection.Setting TCP/IP1. Click the [Start] button first and then [Control Panel].2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click [Network Connections]. A list of cur-rently installed networks will be displayed.4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis-played. The [Wireless Network Connection Proper-ties] window will be displayed.5. Click the [General] tab if it is not already selected.6. Click [Internet Protocol (TCP/IP] and then click [Properties]. The [Internet Protocol (TCP/IP) Properties] window will be displayed.7. Set the IP address as follows:■For ad hoc connection: Select [Use the following IP address:] and then enter data for [IP address] and [Subnet mask]. See page 62 for IP address setting.■For access point (infrastructure) connection: If your network uses DHCP, select [Obtain an IP address automatically] and [Obtain DNS server address automatically]. If your network uses static IP addresses, consult with your network adminis-trator for the correct IP address settings.8. Click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window.9. Click the [OK] button.10. Close the [Network Connection] window. Following this operation, confirm the names of the computer and the workgroup as follows.Confirming the computer and work group names1. Click the [Start] button, then [Control Panel].2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click the [System] icon. The [System Prop-erties] window will be displayed.4. Click the [Computer Name] tab.Field Name DescriptionPower Save ModeOptions are Maximum, Normal, or OffNetwork Type Options are AP (Infrastructure) or Ad Hoc802.11b PreambleSpecifies the preamble setting in 802.11b. The default setting is Short and Long (Access Point mode), which allows both short and long headers in the 802.11b frames. Set to Long Only to override allowing short frames.Transmit Power LevelOptions are 100%, 50%, 25%, 12.5% or Lowest transmit power (0mW)Wireless Mode Specifies 5 GHz 54 Mbps, 5 GHz 108 Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps operation in an access point network.Wireless Mode when Starting Ad Hoc NetworkSpecifies 5GHz 54 Mbps, 5 GHz 108 Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps to start an Ad Hoc network if no matching network name is found after scanning all available modes.To change the setting of the IP address, you need to be logged in from Windows as an administrator.To modify the computer name and/or the work group name, you need to be logged in from Windows as an administrator.P7010.book  Page 55  Monday, December 20, 2004  1:57 PM
56LifeBook P7000 Series Notebook - Section Five5. Confirm the settings of [Full computer name:] and [Workgroup:].a. The setting of [Full computer name:] denotes the name for identifying the computer. Any name can be assigned for each personal computer. Enter the desired name in less than 15 ASCII character code format. Identifiability can be enhanced by entering the model number, the user name, and other factors.b. [Workgroup name] is the group name of the network. Enter the desired name in less than 15 ASCII character code format.For ad hoc connection: Assign the same network name to all personal computers existing on the network.For access point (infrastructure) connection: Assign the name of the work group to be accessed.6. Click the [OK] button. If a message is displayed that requests you to restart the personal computer, click [Yes] to restart the computer.Setting the sharing functionSet the sharing function to make file and/or printer sharing with other network-connected personal computers valid.This operation is not required unless the sharing func-tion is to be used.The folder and printer for which the sharing function has been set will be usable from any personal computer present on the network.Setting the Microsoft network-sharing service1. Click the [Start] button first and then [Control Panel]. 2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click [Network Connections]. A list of cur-rently installed networks will be displayed.4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis-played. The [Wireless Network Connection Proper-ties] window will be displayed.5. If [File and Printer Sharing for Microsoft Net-works] is displayed, proceed to step 6. If [File and Printer Sharing for Microsoft Networks] is not dis-played, skip to step 7.6. Make sure that the [File and Printer Sharing for Microsoft Networks] check box is checked, and then click the [OK] button. Skip to “Setting file-sharing function”.7. Click [Install]. The [Select Network Component Type] window will be displayed.8. Click [Service], then click the [Add] button. The [Select Network Service] window will be displayed.9. Click [File and Printer Sharing for Microsoft Net-works] and then click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window, and [File and Printer Sharing for Microsoft Networks] will be added to the list.10. Click the [Close] button.Setting the file-sharing functionThe procedure for setting the file-sharing function follows, with the “work” folder in drive C: as an example.1. Click the [Start] button first and then [My Com-puter]. 2. Double-click [Local disk (C:)].3. Right-click the “work” folder (or whichever folder you want to share), and then click [Sharing and Security...] in the menu displayed. The [Folder Name Properties] window will be displayed.4. Click [Sharing] if it isn’t already selected.To change the name, click [Change] and then proceed in accordance with the instruction messages displayed on the screen.To share a file and/or the connected printer, you need to be logged in as an administrator. Setting the file-sharing function for the file which has been used to execute Network Setup Wizard is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the file-sharing function easily without using Network Setup Wizard are given below.P7010.book  Page 56  Monday, December 20, 2004  1:57 PM
57WIreless LAN User’s Guide 5. Click the link stating “If you understand the secu-rity risks, but want to share files without running the wizard, click here”.6. Click “Just enable file sharing” and click [OK].7. Check the [Share this folder on the network] check box.8. Click the [OK] button. The folder will be set as a sharable folder, and the display of the icon for the “work.” folder will change.Setting the printer-sharing function1. Click the [Start] button first and then [Printers and FAX]. A list of connected printers will be displayed.2. Right-click the printer for which the sharing func-tion is to be set, and then click [Sharing] in the menu displayed. The property window correspond-ing to the selected printer will be displayed.3. Click the [Sharing] tab.4. Click [Share this printer].5. Enter the sharing printer name in [Share name].6. Click the [OK] button. Confirming connectionAfter you have finished the network setup operations, access the folder whose sharing has been set for other personal computers. Also, confirm the status of the radio waves in case of trouble such as a network connection failure.Connecting your personal computer to another personal computer1. Click [Start] first and then [My Computer]. The [My Computer] window will be displayed in the left frame.2. Click [My Network Places] in the “Other Places” list. The window [My Network Places] will be dis-played.3. Click [View workgroup computers] under Network Tasks in the left frame.4.  Double-click the personal computer to which your personal computer is to be connected. The folder that was specified in “Setting the file-sharing func-tion” on page 56 will be displayed.5. Double-click the folder to be accessed.Confirming the status of the radio1. Right-click the Intel PRO Wireless icon in the lower right corner of the screen.2. Click [Open Intel PROSet for Wireless]. The Intel PROSet for Wireless window opens.3. Contained within the General tab and the Details section (accessed by pressing the [Details] button), you will find the current operating status of the radio. (When the radio is turned off or the com-puter is not yet connected, some of the conditions will not be displayed.)■Profile NameThe current configuration profile is displayed.■Network Name (SSID)Displays the Network Name (SSID) currently used by the radio.■IP AddressThe IP address of the current profile.■Signal QualityDisplays a message stating the current quality of the signal.■Signal StrengthDisplays a graphic representation of the current signal strength.Additionally, in the lower section of the display, you will see a variety of different measurements related to the WLAN. For additional information about the items, click on the “Help?” button:■Adapter MAC Address■Band■Supported Data RatesTo specify the corresponding folder as a read-only folder, select the [Read only] checkbox under the General tab.Setting the printer-sharing function when Network Setup Wizard has been executed is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the printer-sharing function without using Network Setup Wizard are laid down below.In the case of access point (infrastructure) connection, enter the necessary data for the access point before confirming connection. Refer to the manual of the access point for the access point setup procedure.P7010.book  Page 57  Monday, December 20, 2004  1:57 PM
58LifeBook P7000 Series Notebook - Section Five■Radio Frequency■Channel Number■Network Authentication■Data Encryption■802.1x Authentication Type■802.1x Authentication Protocol■CCX Version■CCX TPC■CCX Power Levels■Access Point MAC Address■Mandatory Access PointP7010.book  Page 58  Monday, December 20, 2004  1:57 PM
59WIreless LAN User’s Guide TroubleshootingCauses and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. Problem Possible Cause Possible SolutionUnavailable network connectionIncorrect network name (SSID) or network keyAd hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.Access Point (Infrastructure) connection: set the network name (SSID) and network key to the same values as those of the access point. Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary. For the method of setting network authentication, refer to the following page:·”Assigning parameters” on page 53·Weak received signal strength and/or link qualityAd hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight.Access Point (Infrastructure) connection: Retry connection after short-ening the distance to the access point or removing any obstacles for better sight.To check the wave condition, refer to the following page:· “Confirming the status of the radio waves” on page 57.The WLAN device has been deactivated or disabledCheck if the wireless switch is turned ON. Also verify “Disable Radio” is not checked in “Network setting” window. Refer to “Starting Transmis-sion” on page 52.The computer to be connected is turned offCheck if the computer to be connected is turned ON.RF interference from Access Points or other wireless networksThe use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device.Wireless network authentication has failedRe-check your Network Authentication, Encryption, and Security settings. Incorrectly configured security settings such as an incorrectly typed WEP key, a mis-configured LEAP username, or an incorrectly chosen authentication method will cause the LAN device to associate but not authenticate to the wireless network.Incorrectly configured network settingsRecheck the configuration of your network settings.For the method of checking, refer to the following page:·“Connection to the Network” on page 55.Incorrect IP address configurationThis only applies to networks using static IP addresses. Please contact your network administrator for the correct settings.P7010.book  Page 59  Monday, December 20, 2004  1:57 PM
60LifeBook P7000 Series Notebook - Section FiveWireless LAN GlossaryAd Hoc ModeAd Hoc Mode refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion. For details, refer to “Ad hoc connection” on page 50.ChannelRange of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.DHCP (Dynamic Host Configuration Protocol)A protocol that provides a means to dynamically allocate IP addresses to computers on a local area network.DNS (Domain Name System)A data query service that provides a mechanism with which to translate host names into Internet addresses.IEEE802.11aWireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands. IEEE802.11bWireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz ISM band. Access pointWireless network device used to bridge wireless and wired network traffic. IP addressThe logical 32-bit host address defined by the Internet Protocol that uniquely identifies a computer on a network. The IP address is usually expressed in dotted decimal notation.LAN (Local Area Network)A LAN or Local Area Network is a computer network (or data communications network) which is confined to a limited geographical area.MAC address (Media Access Control Address)A MAC address (also called an Ethernet address or IEEE MAC address) is the 48-bit address (typically written as twelve hexadecimal digits, 0 through 9 and A through F, or as six hexadecimal numbers separated by periods or colons, e.g., 0080002012ef, 0:80:0:2:20:ef) which uniquely identifies a computer that has an Ethernet interface.MTU (Maximum Transmission Unit)The maximum size of data which can be transmitted at one time in networks including the Internet. In an envi-ronment whose maximum size of data is too large to correctly receive data, normal communications can be restored by setting the size of MTU to a smaller value.Network keyData that is used for encrypting data in data communi-cation. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.Network name (SSID: Security Set Identifier)When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.Open system authenticationNull authentication method specified in the 802.11 stan-dard that performs no authentication checks on a wire-less client before allowing it to associate.PPPoE (Point to Point Protocol over Ethernet)A method of allowing the authentication protocol adopted in telephone line connection (PPP) to be used over an Ethernet.ProtocolA procedure or rule of delivering data among computers. Ordered data communication is allowed by making all conditions required for communication including the method of data transmission/reception and actions upon communication errors into proce-dures.P7010.book  Page 60  Monday, December 20, 2004  1:57 PM
61WIreless LAN User’s Guide Shared key authentication802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP. If the client has the wrong key or no key, authentication will fail and the client will not be allowed to associate with the AP. Shared key authentica-tion is not considered secure, because a hacker who detects both the clear-text challenge and the same chal-lenge encrypted with a WEP key can decipher the WEP key.SSID (Service Set Identifier)Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID. Because the SSID is broadcast in plain text, it does not supply any security to the network. Subnet maskTCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.TCP/IP (Transmission Control Protocol/Internet Protocol)A standard protocol of the Internet. Wi-Fi Wi-Fi, or Wireless Fidelity, is a set of standards for wire-less local area networks (WLAN) based on the IEEE 802.11 specifications. Certified products can use the official Wi-Fi logo, which indicates that the product is interoperable with any other product also showing that logo.P7010.book  Page 61  Monday, December 20, 2004  1:57 PM
62LifeBook P7000 Series Notebook - Section FiveIP address informationIf IP address is unknown, set IP address as follows:If you have an access point (DHCP server) on the network, set the IP address as follows:[Obtain an IP address automatically]If the IP address is already assigned to the computer in the network, ask the network administrator to check the IP address to be set for the computer.If no access point is found in the network:An IP address is expressed with four values in the range between 1 and 255.Set the each computer as follows: The value in paren-theses is a subnet mask.<Example>Computer A: 192.168.100.2 (255.255.255.0)Computer B: 192.168.100.3 (255.255.255.0)Computer C: 192.168.100.4 (255.255.255.0)::Computer X: 192.168.100.254 (255.255.255.0)IP addressing is much more complicated than can be briefly explained in this document. You are advised to consult with your network administrator for additional information.A DHCP server is a server that automatically assigns IP addresses to computers or other devices in the network. There is no DHCP server for the AdHoc network.P7010.book  Page 62  Monday, December 20, 2004  1:57 PM
63WIreless LAN User’s Guide Specifications* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/104 bits after subtracting the fixed length of 24 bits.*** Depending on practical environments, the allowable number of computers to be connected may be decreased.Item SpecificationType of network  The Atheros AR5002X and the Intel PRO/Wireless 2915ABG Network Connections WLAN devices conform to IEEE 802.11a and 802.11b/g (Wi-Fi based)*. The Intel PRO/Wireless 2200BG Network Connections WLAN device conforms to 802.11b/g (Wi-Fi based) Transfer rate (Automatic switching)IEEE 802.11a/g: 54 Mbps maximum data rate IEEE 802.11b: 11 Mbps maximum data rateActive frequency 802.11b/g: 2400~2473 MHz 802.11a: 4900 ~ 5850 MHzNumber of channels 802.11a: 8 independent channels802.11b/g: 11 channels, 3 non-overlapping channels Security  Encryption Types - CKIP, WEP, TKIP, AES**WPA 1.0 compliant Encryption Keylengths Supported: 64 bits, 128 bits, and 152 bits (Atheros module using AES encryption only)802.1x/EAPMaximum recommended number of computers to be connected over wireless LAN (during ad hoc connection)10 units or less ***P7010.book  Page 63  Monday, December 20, 2004  1:57 PM
64LifeBook P7000 Series Notebook - Section FiveP7010.book  Page 64  Monday, December 20, 2004  1:57 PM
656TroubleshootingP7010.book  Page 65  Monday, December 20, 2004  1:57 PM
66LifeBook P7000 Notebook – Section SixP7010.book  Page 66  Monday, December 20, 2004  1:57 PM
67TroubleshootingTroubleshootingYour Fujitsu LifeBook notebook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.IDENTIFYING THE PROBLEMIf you encounter a problem, go through the following procedure before pursuing complex troubleshooting:1. Turn off your LifeBook notebook.2. Make sure the AC adapter is plugged into your note-book and to an active AC power source.3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.5. Turn on your notebook. Make sure it has been off at least 10 seconds before you turn it back on.6. Go through the boot sequence.7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information. 8. If you are still having problems after referring to the Troubleshooting Table, go to the Fujitsu Computer Systems Support website (http://www.computers.us.fujitsu.com/support), and search the list of Frequently Asked Questions (FAQs) contained there. 9. If you have tried the solutions suggested above without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) Fax: 408-764-2724 E-mail: 8fujitsu@us.fujitsu.com Web site: http://www.computers.us.fujitsu.com/supportBefore you place the call, you should have the following information ready so that the customer support represen-tative can provide you with the fastest possible solution:■Product name■Product configuration number■Product serial number■Purchase date■Conditions under which the problem occurred■Any error messages that have occurred■Type of device connected, if anySee the Configuration Label on the bottom of yournotebook for configuration and serial numbers. (See figure 2-7 on page 11 for location)SPECIFIC PROBLEMSUsing the Troubleshooting TableWhen you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your notebook.If you keep notes about what you have tried, your support representative may be able to help you more quickly by giving additional suggestions over the phone.P7010.book  Page 67  Monday, December 20, 2004  1:57 PM
68LifeBook P7000 Notebook – Section SixTROUBLESHOOTING TABLEProblem PageAudio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 68DVD/CD-RW Drive Problems . . . . . . . . . . . . . . page 68Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 69Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 69Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 69Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 70Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 70 Problem PageUSB Device Problems . . . . . . . . . . . . . . . . . . . . . page 70PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 70Power Failures  . . . . . . . . . . . . . . . . . . . . . . . . . . . page 71Shutdown and Startup Problems . . . . . . . . . . . . page 72Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 73Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 74Problem Possible Cause Possible SolutionsAudio ProblemsThere is no sound coming from the built-in speakers.The software volume control is set too low.Adjust the sound volume control settings in your software, operating system and applications.Headphones are plugged into your notebook.Plugging in headphones disables the built-in speakers; remove the headphones.BIOS audio settingsare incorrect.Set the BIOS setup utility to the default values within the Multimedia Device Configuration menu. (See BIOS Setup Utility on page 25 for more information)Software driver is not configured correctly.Refer to your application and operating system documentation for help.DVD/CD-RW Drive ProblemsLifeBook notebook fails to recognize DVD/CD-RW discProtective sheet is still in the DVD/CD-RW drive tray.Remove the protective sheet from the tray.The disc is not pushed down onto raised center of the drive.Open DVD/CD-RW tray and re-install DVD/CD-RW disc properly.DVD/CD-RW drive tray is not latched shut.Push on the front of the DVD/CD-RW drive tray until it latches.Incorrect DVD Player or no DVD Player software is installed.Install DVD Player software. (See “Using the Optical Drive Software” on page 35 for more information.)Wrong drive designator was used for DVD/CD-RW drive in the application.Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a DVD/CD, drive designations are automatically adjusted.Windows DVD/CD-RW auto insertion function is disabled.Start the DVD/CD-RW drive from the desktop or application software or re-enable the Windows DVD/CD-RW auto insertion function. (See Auto Insert Notification Function on page 36 for more information)DVD/CD-RW disc is dirty or defective.Wipe disc with non-abrasive cleaning cloth and reinsert. It if still will not work try a different disc.The DVD/CD-RW Access indicator on the Status Indicator Panel blinks at regular intervals when no disc is in the tray or the drive is not installed.The Windows DVD/CD-RW auto insertion function is active and is checking to see if a DVD/CD-RW disc is ready to run. This is normal. However, you may disable this feature. (See Auto Insert Notification Function on page 36 for more information)P7010.book  Page 68  Monday, December 20, 2004  1:57 PM
69TroubleshootingFloppy Disk Drive ProblemsYou cannot access your optional floppy disk.You tried to write to a write protected floppy disk.Eject the floppy disk and set it to write enable. (See Preparing a Disk for Use on page 33 for more informa-tion)Floppy disk is not loaded correctly.Eject floppy disk, check orientation and re-insert. (See Ejecting a Disk on page 33 for more information)Security is set to protect access to floppy disk data.Verify your password and security settings.Hard Drive ProblemsYou cannot access your hard drive.The setup utility is incorrectly set for your internal (Primary Master) or optional second hard drive (Primary Slave).Revise BIOS settings to set both Primary Masterand Primary Slave correctly. (See BIOS Setup Utility on page 25 for more information)The wrong drive designator was used by an application when a bootable CD-ROM was used to start the notebook.Verify drive designator used by application is inuse by the operating system. When the operating system is booted from a CD, drive designationsare automatically adjusted. Security is set so your operating system cannot be started without a password.Verify your password and security settings.Keyboard or Mouse ProblemsThe built-in keyboard does not seem to work.The notebook has gone into Suspend mode.Push the Suspend/Resume/Power On button.Your application has locked out your keyboard.Try to use your integrated pointing device to restart your system. If this fails, turn your notebook off by pressing the Power/Suspend/Resume button for several seconds. After the system has been off for at least 10 seconds, turn it back on.The characters that appear do not match those which you typed.NumLk is set in the BIOS. Go to the BIOS and make sure that NumLk is disabled. (See BIOS Setup Utility on page 25 for more information)You have installed an external keyboard or mouse, and it does not seem to work.Your external device is not prop-erly installed.Re-install your device. (See Device Ports on page 44 for more information)Your operating system software is not setup with the correct soft-ware driver for that device.Check your device and operating system docu-mentation and activate the proper driver.You have connected an external keyboard or a mouse and it seems to be locking up the system.Your operating system software is not setup with the correct soft-ware driver for that device.Check your device and operating systemdocumentation and activate the proper driver.Your system has crashed. Try to restart your notebook. If this fails, turn your notebook off by pressing the Power/Suspend/Resume button for several seconds. After the system has been off for at least 10 seconds, turn it back on.Problem Possible Cause Possible SolutionsP7010.book  Page 69  Monday, December 20, 2004  1:57 PM
70LifeBook P7000 Notebook – Section SixMemory ProblemsYour Power On screen, or Info menu of the BIOS setup utility information, does not show the correct amount of installed memory.Your memory upgrade module is not properly installed.Remove and re-install your memory upgrade module. (See Memory Upgrade Module on page 42 for more information)You have a memory failure. Check for Power On Self Test (POST) messages. (See Power On Self Test Messages on page 75 for more information)Modem ProblemsMessages about modem operation.Messages about modem opera-tion are generated by whichever modem application is in use.See your application software documentation for additional information.USB Device ProblemsYou have installed a USB device but your LifeBook notebook does not recog-nize the device, or the device does not seem to work properly.The device is not properly installed.Remove and re-install the device. (See Device Ports on page 44 for more information)The device may have been installed while an application was running, so your notebook is not aware of its installation.Close the application and restart your notebook.Your software may not have the correct software driver active.See your software documentation and activate the correct driver.You may have the wrong I/O address selected for your device.See your device documentation and software docu-mentation to determine the required I/O address. Change the settings in the BIOS setup utility. (See BIOS Setup Utility on page 25 for more information)Your device and another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.PC Card ProblemsA card inserted in the PC Card slot does not work or is locking up the system.The card is not properly installed.Remove and re-install the card. (See PC Cards on page 37 for more information)The card may have been installed while an application was running, so your notebook is not aware of its installation.Close the application and restart your notebook.Your software may not have the correct software driver active.See your software documentation and activate the correct driver.You may have the wrong I/O address selected for your PC Card device.See your PC Card documentation to determinethe required I/O address. Change the settings inthe BIOS. (See BIOS Setup Utility on page 25 for more information)Yo u r  PC  Ca rd  de v i ce  an d  another device are assigned the same I/O address.Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.Problem Possible Cause Possible SolutionsP7010.book  Page 70  Monday, December 20, 2004  1:57 PM
71TroubleshootingPower FailuresYou turn on your LifeBook notebook and nothing seems to happen.The installed primary battery is completely discharged, there is no optional second battery installed or there is no Power adapter installed.Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel on page 12 for more information) Install a charged battery or a Power adapter.The primary battery is installed but is faulty.Use the Status Indicator panel to verify the presence and condition of the batteries. (See Status Indicator Panel on page 12 for more information) If a battery is indicating a short, remove that battery and operate from another power source or replace that battery.The battery or batteries are low. Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel on page 12 for more information) Use a Power adapter to operate until a battery is charged or install a charged battery.The adapter (AC or auto/airline) is not plugged in properly.Verify that your adapter is connected correctly. (See Power Sources on page 23 for more information)The Power adapter (AC or auto/airline) has no power from the AC outlet, airplane seat jack, or the car’s cigarette lighter.Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.The Power adapter (AC or auto/airline) is faulty.Try a different Power adapter or install a charged optional second battery.Your LifeBook notebook turns off all by itself.The power management param-eters are set for auto timeouts which are too short for your operating needs.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings, or close your applicationsand go to the Power Savings menu of the setup utility to adjust the timeout values to better suityour operation needs.You are operating on battery power only and have ignored a low battery alarm until the battery is at dead battery state and your system has gone into Dead Battery Suspend mode.Install a power adapter and then push the Suspend/Resume button. (See Power Sources on page 23 for more information)You have a battery failure. Verify the condition of the batteries using theStatus Indicator panel, and replace or removeany batteries that are shorted. (See Status Indicator Panel on page 12 for more information)Your power adapter has failed or lost its power source.Make sure the adapter is plugged in and the outlet has power.Your LifeBook notebook will not work on battery alone.The installed batteries are dead. Replace the battery with a charged one or install a Power adapter.No batteries are installed. Install a charged battery.Problem Possible Cause Possible SolutionsP7010.book  Page 71  Monday, December 20, 2004  1:57 PM
72LifeBook P7000 Notebook – Section SixYour LifeBook notebook will not work on battery alone.(continued)The batteries are improperly installed.Verify that the batteries are properly connected by re-installing them.Your installed batteries are faulty.Verify the condition of the batteries using the Status Indicator panel and replace or remove any batteries that are shorted. (See Status Indicator Panel on page 12 for more information)The batteries seem to discharge too quickly.You are running an application that uses a lot of power due to frequent hard drive or DVD/CD-RW drive access, or use of a modem or LAN PC card.Use both the primary battery and an optional second battery and/or use a power adapter for this application when at all possible.The power savings features may be disabled.Check the power management and/or setup utility settings in the Power Savings menu and adjust according to your operating needs.The brightness is turned all the way up.Turn down the brightness adjustment. The higher the brightness the more power your display uses.The batteries are very old. Replace the batteries.The batteries have been exposed to high temperatures.Replace the batteries.The batteries are too hot or too cold. Restore the notebook to normal operating tempera-ture. The Charging icon on the Status Indicator panel will flash when the battery is outside itsoperating range.Shutdown and Startup ProblemsThe Suspend/Resume/Power On button does not work.The Suspend/Resume/Power On button is disabled from the Advanced submenu of the Power menu of the setup utility. Enable the button from the setup utility.You did not hold the button in long enough.Hold the button longer. This may need to be a few seconds if your application is preventing the CPU from checking for button pushes.There may be a conflict with the application software.Close all applications and try the button again.The system powers up, and displays power on information, but fails to load the operating system.Boot sequence settings of the setup utility are not compatible with your configuration.Set the operating source by pressing the [F12] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. (See BIOS Setup Utility on page 25 for more information)You have a secured system requiring a password to load your operating system.Make sure you have the right password. Enter the setup utility and verify the Security settings and modify them as accordingly. (See BIOS Setup Utility on page 25 for more information)Internal hard drive was not detected.Use the BIOS setup utility to try to auto detect the internal hard drive. If this does not work, contact Fujitsu Service and Support at 1-800-8FUJITSU.Problem Possible Cause Possible SolutionsP7010.book  Page 72  Monday, December 20, 2004  1:57 PM
73TroubleshootingAn error message is displayed on the screen during the notebook (boot) sequence.Power On Self Test (POST) has detected a problem.See the Power On Self Test (POST) messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. (See Power On Self Test Messages on page 75 for more information)Your notebook appears to change setup parameters when you start it.BIOS setup changes were not saved when you made them and exited the BIOS setup utility returning it to previous settings.Make sure you select Save Changes And Exit when exiting the BIOS setup utility.The BIOS CMOS hold-up battery has failed.Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years.Video ProblemsThe built-in display is blank when you turn on your LifeBook notebook.The notebook is set for an external monitor only.Pressing [F10] while holding down the [Fn] key allows you to change your selection of where tosend your display video. Each time you press the combination of keys you will step to the nextchoice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.The display angle and brightness settings are not adequate for your lighting conditions.Move the display and the brightness control until you have adequate visibility.The power management time-outs may be set for very short intervals and you failed to notice the display come on and go off.Press any button the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standby mode, Auto Suspend or Video Timeout)The notebook is set for S-Video display only.While holding down the [Fn] key, click on the [F11] key to toggle the S-Video display off.The LifeBook notebook turned on with a series of beeps and your built-in display is blank.Power On Self Test (POST) has detected a failure which does not allow the display to operate.Contact your support representative.The display goes blank by itself after you have been using it.The notebook has gone into Video timeout, Standby mode, Suspend mode or Hibernation mode because you have not used it for a period of time.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. Check your power management settings to adjust the timeout values to better suit your operation needs. (See BIOS Setup Utility on page 25 for more information)The power management time-outs may be set for very short intervals and you failed to notice the display come on and go off.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout)The Built-in Display does not close.A foreign object, such as a paper clip, is stuck between the display and the keyboard.Remove all foreign objects from the keyboard.Problem Possible Cause Possible SolutionsP7010.book  Page 73  Monday, December 20, 2004  1:57 PM
74LifeBook P7000 Notebook – Section SixThe Built-in Display has bright or dark spots.If the spots are very tiny and few in number, this is normal for a large LCD display.This is normal; do nothing.If the spots are numerous or large enough to interfere with your operation needs.Display is faulty; contact your support representative.The application display uses only a portion of your screen and is surrounded by a dark frame.You are running an application that does not support 800 x 600/1024 x 768 pixel resolution display and display compression is enabled.Display compression gives a clearer but smaller display for applications that do not support 800 x 600/1024 x 768 pixel resolution. You can fill the screen but have less resolution by changing your display compression setting, (See the Video Features submenu, located within the Advanced menu of the BIOS. (See BIOS Setup Utility on page 25 for more information)The display is dark when on battery power.The default is set on low bright-ness to conserve power.Press [Fn] + [F7] to increase brightness and adjust Power Control under battery settings.You have connected an external monitor and it does not display any information.Your BIOS setup is not set to enable your external monitor.Toggle the video destination by pressing [Fn] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS. (See BIOS Setup Utility on page 25 for more information)Your external monitor is not properly installed. Reinstall your device. (See External Monitor Port on page 46 for more information)Your operating system software is not setup with the correct soft-ware driver forthat device. Check your device and operating systemdocumentation and activate the proper driver.You have connected an external monitor and it does not come on.Your external monitor is not compatible with your LifeBook notebook.See your monitor documentation and theExternal Monitor Support portions of theSpecifications section. (See Specifications on page 87 for more information)Miscellaneous ProblemsAn error message is displayed on the screen during the operation ofan application.Application software often has its own set of error message displays. See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.Problem Possible Cause Possible SolutionsP7010.book  Page 74  Monday, December 20, 2004  1:57 PM
75TroubleshootingPOWER ON SELF TEST MESSAGESThe following is an alphabetic list of error-and-status messages that the Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes success-fully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)*Diskette drive A error or Diskette drive B error Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility on page 25 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative.*Extended RAM Failed at offset: nnnn Extended memory not working or not configured prop-erly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is prop-erly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representative.nnnn Extended RAM Passed Where nnnn is the amount of memory in kilobytes successfully tested.*Failing Bits: nnnn The hex number nnnnThis is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4) The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.*Incorrect Drive A type – run SETUP Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.*Incorrect Drive B type – run SETUPType of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.*Invalid NVRAM media typeProblem with NVRAM access. In the unlikely case that you see this message you may have some display prob-lems. You can continue operating but should contact your support representative for more information.*Keyboard controller error The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.*Keyboard error Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able touse an external keyboard until then. Contact your support representative.*Keyboard error nn BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.*Monitor type does not match CMOS – Run SETUPMonitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted and your system may have to be re-installed from your back up media.*Parity Check 1 nnnn Parity error found in the system bus. BIOS attemptsto locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is apotentially data destroying failure. Contact yoursupport representative.P7010.book  Page 75  Monday, December 20, 2004  1:57 PM
76LifeBook P7000 Notebook – Section Six*Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is apotentially data-destroying failure. Contact yoursupport representative.*Press <F1> to resume, <F2> to SETUP Displayed after any recoverable error message. Pressthe [F1] key to continue the boot process or the [F2]key to enter Setup and change any settings.*Previous boot incomplete – Default configuration used Previous Power On Self Test did not complete success-fully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power and contact your support representative.*Real time clock error Real-time clock fails BIOS test. May require board repair. Contact your support representative.*Shadow RAM Failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corrup-tion if you continue. Contact your support representative.nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested.*System battery is dead – Replace and run SETUP The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your notebook. This battery has an expected life of 2 to 3 years.System BIOS shadowed System BIOS copied to shadow RAM.*System CMOS checksum bad – run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. Run Setup and reconfigure the system.*System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.nnnn System RAM PassedWhere nnnn is the amount of system memory inkilobytes successfully tested.*System timer error The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.Video BIOS shadowed Video BIOS successfully copied to shadow RAM.EMERGENCY DVD TRAY RELEASEIf for some reason the eject button fails, you can open the DVD/CD-RW tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clipand push it gently into the hole. The tray will pop outa short distance.MODEM RESULT CODESThe operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are:■OK■NO CARRIER■NO DIALTONE■CONNECT 53000 (Connection complete at 53,000 bps.)■ERROR■FAX■RING (This means an incoming call.)■BUSY■NO ANSWERWhen using the internal modem with applicationsthat are not factory installed refer to theapplication documentation.P7010.book  Page 76  Monday, December 20, 2004  1:57 PM
77TroubleshootingRestoring Your Pre-installed SoftwareThe Drivers and Applications Restore (DAR) DVD contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your notebook configuration for use as documented below.Re-Installing Individual Drivers and Applications The Drivers and Applications CD can be used to selec-tively re-install drivers and/or applications that may have been un-installed or corrupted. To re-install drivers and/or applications:1. Boot up the system and insert the DAR CD after Windows has started. A Fujitsu Installer screen is displayed after the CD is inserted.2. After reading the License Agreement, click [I agree].3. A window will appear containing a list of applica-tions, drivers, and utilities that you can install from the Drivers and Applications CD.4. In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately.5. Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed.6. After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system. RESTORING THE FACTORY IMAGEThe Restore Disc that came with your system contains two utilities:■The Recovery utility allows you to restore the original contents of the C: drive.■The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.BOOT Priority ChangeBefore restoring an image, you must first verify that your system is set up to boot from the DVD drive. To verify/change the boot-up priority (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps:1. Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.2. Using the arrow keys, go to the Boot menu.3. Arrow down to the Boot Device Priority submenu. Press [Enter].4. If “Optical Media Drive” or “CD-ROM Drive” is not at the top of the list, arrow down to the drive in the list, and press the space bar (or the + key) to move it to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.). Note that the BIOS for some systems will indicate “CD-ROM Drive”, even when a DVD drive is connected.5. If you have an external DVD drive connected, proceed to step 6; otherwise, proceed to step 7.6. If you have an external DVD drive connected:• Select the Advanced menu in the BIOS window.• Scroll down to the USB Features submenu and press the Enter key to open it.If you have access to the internet, visit the Fujitsu Support web site at http://www.computers.us.fujitsu.com/support to check for the most current information, drivers and hints on how to perform recovery and system updates. (See Automatically Downloading Driver Updates on page 78 for more information)There may be certain free third-party applications pre-installed on your system that are not on the DAR CD. The latest versions of the applications can be downloaded from the third-party’s website.The components listed are color-coded in terms of their install status. Blue indicates that the component can be installed. Green indicates that the component needs to be installed separately. Grey indicates a component that is already installed; grey items can be reinstalled, but prior to installation you will receive a reminder that the component is already installed. • The use of this disc requires that you have a device capable of reading DVDs attached to your system. If you do not have a built-in DVD player, you will need to attach an external player. For more information on available external devices, visit our Web site at: us.fujitsu.com/computers. • This disc can only be used with the system with which it was purchased.P7010.book  Page 77  Monday, December 20, 2004  1:57 PM
78LifeBook P7000 Notebook – Section Six• If Legacy USB Support is disabled, press the space bar to enable it.• Scroll down to SCSI SubClass Support and press the space bar to enable it. 7. Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.After you have changed the boot priority, you can restore a backup image when you are booting up.Procedure1. Turn on the power to your system.2. Ensure that you have a device that can read DVDs either installed in your system or attached exter-nally to it.3. Insert the Restore Disc into the drive tray.4. Reboot your system.5. After the system reboots, follow the instructions that appear to either restore your system image or erase all data from your hard disk.AUTOMATICALLY DOWNLOADING DRIVER UPDATESYour system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system.The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one). If the FDU icon does not appear in the system tray, it can be started by going to [Start] -> All Programs, and clicking on Fujitsu Driver Update; this will create the icon automatically.To invoke the FDU menu, right-click on the FDU icon. The menu contains the following items:■Check for updates nowAllows for manual driver update search. The first time it is used, you are prompted to agree to a user agreement. After clicking on the icon, the FDU auto-matically connects with the Fujitsu site to check for updates and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be used while the download is in process. When the update is complete, a message appears informing you of the fact.■Enable Automatic Update NotificationsAutomatically searches for new updates on a regular basis (approximately every 3 days).■Show update historyBrings up a screen that displays a history of updates that have been made via the FDU.■About Fujitsu Driver UpdateDisplays the FDU version number and copyright information■Fujitsu Driver Update ReadmeDisplays the FDU readme.P7010.book  Page 78  Monday, December 20, 2004  1:57 PM
797Care and MaintenanceP7010.book  Page 79  Monday, December 20, 2004  1:57 PM
80LifeBook P7000 Notebook – Section SevenP7010.book  Page 80  Monday, December 20, 2004  1:57 PM
81Care and MaintenanceCare and MaintenanceIf you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices.Caring for your LifeBook notebook■Your LifeBook notebook is a durable but sensitive elec-tronic device. Treat it with respect and care.■Make a habit of transporting it in a suitable carrying case.■Do not attempt to service the computer yourself. Always follow installation instructions closely.■Keep it away from food and beverages.■If you accidentally spill liquid on your LifeBook note-book:1.Turn it off.2.Position it so that the liquid can run out.3.Let it dry out for 24 hours, or longer if needed.4.If your notebook will not boot after it has dried out, call your support representative.■Do not use your Fujitsu LifeBook notebook in a wet environment (near a bathtub, swimming pool).■Always use the AC adapter and batteries that are approved for your notebook.■Avoid exposure to sand, dust and otherenvironmental hazards.■Do not expose your notebook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your notebook.■Keep the covers closed on the connectors and slots when they are not in use.■Do not put heavy or sharp objects on the computer.■If you are carrying your LifeBook notebook in a brief-case, or any other carrying case, make sure that there are no objects in the case pressing on the lid.■Never position your notebook such that the DVD/CD-RW drive is supporting the weight of the notebook. ■Do not drop your notebook.■Do not touch the screen with any sharp objects. Cleaning your LifeBook notebook■Always disconnect the power plug. (Pull the plug, not the cord.)■Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.■Use a soft cloth to remove dust from the screen.Never use glass cleaners.Storing your LifeBook notebook■If storing your notebook for a month or longer, turn your LifeBook notebook off, charge the battery, then remove and store all Lithium ion batteries.■Store your notebook and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addi-tion, a faulty battery might damage your LifeBook.■Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between 13ºF (-10ºC) and 140ºF (60ºC).Traveling with your LifeBook notebook■Do not transport your notebook while it is turned on. ■Do not check your notebook as baggage. Carry it with you.■Always bring your backup disk and Drivers and Applications CD that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any prob-lems. ■Never put your notebook through a metal detector. Have your notebook hand-inspected by security per-sonnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel. Secu-rity officials may require you to turn your notebook On. Make sure you have a charged battery on hand. ■When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine. ■Take the necessary plug adapters if you're traveling over-seas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.Electrical equipment may be hazardous if misused. Operations of this product or simi-lar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.P7010.book  Page 81  Monday, December 20, 2004  1:57 PM
82LifeBook P7000 Notebook – Section SevenBATTERIESCaring for your Batteries■Always handle batteries carefully.■Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.■Do not drop, puncture, disassemble, mutilate or incin-erate the battery.■Recharge batteries only as described in this manual and only in ventilated areas.■Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.■Do not leave a battery in storage for longer than 6 months without recharging it.Increasing Battery Life■Power your LifeBook notebook through the AC or optional auto/airline adapter whenever possible.■If your notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.■Keep brightness to the lowest level comfortable.■Set the power management for maximum battery life.■Put your notebook in Suspend mode when it is turned on and you are not actually using it.■Limit your media drive access.■Disable the DVD/CD-RW Combo Drive auto insert noti-fication function.■Always use fully charged batteries.■Eject PCMCIATM cards when not in use.FLOPPY DISKS AND DRIVESCaring for your Floppy Disks■Avoid using the floppy disks in damp anddusty locations.■Never store a floppy disk near a magnet or magnetic field.■Do not use a pencil or an eraser on a disk or disk label.■Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).■Do not touch the exposed part of the diskbehind the metal shutter.Caring for your Floppy Disk Drive■To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.■Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe tempera-ture changes. Store at temperatures between 50º F (10º C) and 125ºF (52º C).■Keep the floppy disk drive out of direct sunlight and away from heating equipment.■Avoid storing the floppy disk drive in locations subject to shock and vibration.■Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy diskdrive or disk.■Never disassemble or dismantle your floppy disk drive.Outlet Type LocationUnited States, Canada,parts of Latin America,Mexico, Japan, Korea,the Philippines, TaiwanRussia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South AsiaUnited Kingdom, Ireland, Malaysia, Singapore, parts of AfricaChina, Australia,New Zealand P7010.book  Page 82  Monday, December 20, 2004  1:57 PM
83Care and MaintenanceMEDIA CARECaring for your Media (DVD/CD-RW/CD-ROM)Media discs are precision devices and will function reli-ably if given reasonable care.■Always store your media disc in its case when it is not in use.■Always handle discs by the edges and avoid touching the surface.■Avoid storing any media discs in extreme temperatures.■Do not bend media discs or set heavy objects on them.■Do not spill liquids on media discs.■Do not scratch media discs.■Do not get dust on media discs.■Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.■If a media disc is subjected to a sudden change in tem-perature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry media discs.■If a disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.Caring for your DVD/CD-RW DriveYour DVD/CD-RW drive is durable but you must treat it with care. Please pay attention to the following points:■The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.■Avoid using or storing the drive where it will be exposed to extreme temperatures.■Avoid using or storing the drive where it is damp or dusty.■Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.■Avoid using or storing the drive where it will be sub-jected to shock or vibration.■Do not disassemble or dismantle the DVD/CD-RW drive.■Occasional use of a commercially available lens cleaner kit is recommended to maintain your drive.PC CARDSCaring for your PC Cards PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Cardwill provide specific information, but you should pay attention to the following points:■To keep out dust and dirt, store PC Cards in theirprotective sleeves when they are not installed in your LifeBook notebook.■Avoid prolonged exposure to direct sunlight orexcessive heat.■Keep the cards dry.■Do not flex or bend the cards, and do not place heavy objects on top of them.■Do not force cards into the slot.■Avoid dropping cards, or subjecting them toexcessive vibration.P7010.book  Page 83  Monday, December 20, 2004  1:57 PM
84LifeBook P7000 Notebook – Section SevenP7010.book  Page 84  Monday, December 20, 2004  1:57 PM
858SpecificationsP7010.book  Page 85  Monday, December 20, 2004  1:57 PM
86LifeBook P7000 Notebook – Section EightP7010.book  Page 86  Monday, December 20, 2004  1:57 PM
87SpecificationsSpecificationsThis section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook.Specifications of particular configurations will vary.CONFIGURATION LABELThe configuration label located on the bottom of your LifeBook notebook (See figure 2-7 on page 11 for location) contains information regarding the options you’ve chosen for your notebook. Following is an example label and information on how to read your own configuration label.Figure 8-1 Configuration LabelMICROPROCESSORIntel® Pentium® M Ultra Low Voltage (ULV) or Intel® Celeron® M Ultra Low Voltage (ULV). For the processor speed of your LifeBook, check the configuration label.■400 MHz system bus speed ■64 KB L1 cache memory■2 MB on-die L2 cache memory (Pentium) or 512 KB (Celeron)MEMORYSystem Memory■256 MB minimum, 1 GB maximum, micro-DIMM DDR SDRAM■Two micro-DIMM slots■256 MB and 512 MB memory modules are availableBIOS Memory1 MB Firmware Hub (FWH) Flash ROMVIDEOBuilt-in color 10.6” Wide XGA Crystal View TFT active matrix LCD display with simultaneous display capabilityVideo Color and Resolution10.6" TFT Wide XGA■Internal: 1280 x 768 pixel resolution, 16M colors■External: 1600 x 1200 pixel resolution, 16M colorsSimultaneous Video = Yes (1024 x 768, 16M colors) XGA, SVGA and VGA compatibleVideo RAMIntel® 855GME or 852GML video graphics chip with integrated 32-bit 3D/2D gfx core and Accelerated Graphics Port (AGP) support. Up to 64 MB shared video memory using Dynamic Video Memory Technology 2.0.AUDIO■Realtek ALC203 codec with 18-bit stereo audio■Stereo headphone/Optical Digital (SPDIF) port ■Mono microphone jack, 100 mVrms max.■Dolby Headphone signal processing utility (in the InterVideo DVD software)■Two built-in stereo speakers, 25 mm x 14 mm, bass reflex■Built-in microphone on palm restMASS STORAGE DEVICE OPTIONSHard Drive40 GB, 60 GB, or 80 GB fixed hard drive, 2.5”, ATA 100Modular DVD/CD-RW Combo Drive8x DVD / 10x CD-RW / 24x CD-R / 24x CD-ROMModular Multi-Format DVD Writer2x DVD-R, 2x DVD-RW, 2.4x DVD+R, 2.4x DVD+RW, 2x DVD-RAM, 8x DVD-ROM, 24x CD-R, 10x CD-RW, 24x CD-ROMFEATURESCommunications■Modem: Internal V.90 standard 56K* fax/modem(ITU V.90, 56K data, 14.4K fax) ■LAN: 10/100 Base-TX Ethernet ■Integrated Intel PRO/Wireless 2200BG Network Connections (802.11b/g*) with Antenna On/Off switch (available in LifeBook P7010 model), or,■Integrated Intel PRO/Wireless 2915ABG Network Connections (802.11a+b/g**) with Antenna On/Off switch (available in LifeBook P7010 model), or,■Integrated Atheros Super AG Wireless LAN (802.11a/b/g**) with Antenna On/Off switch (available in Life-Book P7010D model)■Optional Bluetooth device for wireless personal area network communication*      Operates at 2.4 GHz; communications range may vary, depending upon environment.**    Operates at 2.4 GHz and 5.0 GHz; communications range may vary, depending upon environment.P7010, PM ULV 733, 10.6 WXGA, 256M, 60G, MODEM/LAN/WLAN, WIN XPHConfiguration P/N: AWPXXXXXXXXXXXXXFPC P/N: FPCMXXXXXXOperating Hard Drive Configuration IDPart NumberProcessorModel #Screen Size Memory SystemCommunicationsP7010.book  Page 87  Monday, December 20, 2004  1:57 PM
88LifeBook P7000 Notebook – Section EightIntegrated Pointing DeviceTouchpad pointing device with scroll button. (Scroll button is replaced with optional fingerprint sensor in some configurations)Theft Prevention Lock SlotSlot for use with physical restraining security systems. DEVICE PORTS■PC Card slot for one Type II card: PCMCIA Standard 2.1 with CardBus support■One connector for external monitor (see Display specifications)■One Compact Flash Card slot■One SD/Memory Stick slot■Two USB 2.0 connectors for input/output devices■One S-Video Out port■One modular modem (RJ-11) connector■One LAN (RJ-45) port■One IEEE 1394 port■One stereo headphone/Optical Digital (SPDIF) jack. (See Audio specifications)■One mono microphone jack. (See Audio specifications)KEYBOARDBuilt-in keyboard with all functions of 101 key keyboards.■Total number of keys: 82■Function keys: [F1] through [F12]■Feature extension key: [Fn]■Two Windows keys: one Start and one application key ■Key pitch: 17.5 mm■Key stroke: 2 mm■Built-in Touchpad pointing device with left and right buttons and scroll button.■Built-in palm restExternal Keyboard SupportUSB-compatibleExternal Mouse SupportUSB-compatiblePOWERBatteries■One standard 6-cell high-capacity Lithium ion battery, rechargeable, 10.8V, 4800 mAh. (Approximate charge time: system off: 6.5 hours, system running: 17 hours)■Optional second bay battery: 6-cell Lithium ion battery, rechargeable, 10.8V, 2300 mAhAC AdapterAutosensing 100-240V AC, 60W, supplying 16V DC, 3.75A, to the LifeBook notebook, Fujitsu Model FPCAC37AP, which includes an AC cable.Power ManagementConforms to ACPI (Advanced Configuration and Power Interface)DIMENSIONS AND WEIGHTOverall DimensionsApproximately 10.28"(w) x 7.83"(d) x 1.26/1.428"(h) (261mm x 199 mm x 32/36 mm)WeightsApproximately 3.28 lbs (1.50 kg) with standard high capacity battery and DVD/CD-RW combo driveENVIRONMENTAL REQUIREMENTSTemperatureOperating: 41° to 95° F (5° to 35° C)Non-operating: 13° to 140° F (–10° to 60° C)HumidityOperating: 20% to 85%, relative, non-condensingNon-operating; 8% to 85%, relative, non-condensingAltitudeOperating: 10,000 feet (3,048 m) maximumPOPULAR ACCESSORIESFor ordering or additional information on Fujitsu accessories please visit our Web site at:us.fujitsu.com/computers or call 1-877-372-3473.Memory Upgrade■256 MB Double Data Rate (DDR) SDRAM (micro DIMM)■512 MB Double Data Rate (DDR) SDRAM (micro DIMM)Power■Additional standard High Capacity Lithium ion battery■Modular 2nd Lithium ion Battery■Auto/Airline Adapter■AC Adapter■Battery ChargerFlexible Bay Devices■Modular DVD/CD-RW combo drive■Modular Multi-Format DVD Writer■Modular second Lithium ion batteryAdditional Accessories■USB Optical Mouse■Wireless Keyboard and Mouse■Notebook Guardian Lock■External Floppy Disk DriveCarrying Cases■Diplomat■Dual Carrying Case■Director■Moda BackpackP7010.book  Page 88  Monday, December 20, 2004  1:57 PM
89SpecificationsPRE-INSTALLED SOFTWAREDepending on your pre-installed operating system, your Fujitsu LifeBook notebook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. LEARNING ABOUT YOURAPPLICATION SOFTWARETutorialsAll operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application.ManualsIncluded with your notebook you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included, are avail-able online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications.Adobe Acrobat ReaderThe Adobe Acrobat Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms. Norton AntiVirus 2004Your system is preinstalled with a free 90-day trial version of Symantec’s Norton AntiVirus™ 2004. Norton AntiVirus is a program designed to protect your Life-Book notebook from computer viruses. It assists in the protection of the data currently residing on your hard disk from destruction or contamination. The 90-day trial version is activated upon your acceptance of soft-ware license agreement. After 90 days, it will be neces-sary to purchase a subscription from Symantec to download latest virus definitions.  (See your online help or manual for more information on how and when to run this program).Fujitsu HotKey UtilityUtility for adjusting the brightness level on your Life-Book.Quicken 2004 New User Edition Quicken 2004 New User Edition by Intuit is a personal money management program. It has features such as portfolio management, account registries, on-line banking and bill paying features. This application is for new users who are using Quicken software for the first time. Full version upgrade information is available on line.MS Works Microsoft Works is a suite of software containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory.Depending upon your system configuration, one of the following applications will be installed on your note-book:Microsoft Works 7.0 Microsoft Works 7.0 is a suite of software containing the basic tools to write letters and reports, track family and friends with address books, manage home finances, and create a home inventory.Microsoft Office SBEMicrosoft Small Business Edition (SBE) is a suite of applications designed to help run a small business while increasing productivity. Among the programs included in Microsoft SBE are Microsoft Word, Excel, and Power-Point. P7010.book  Page 89  Monday, December 20, 2004  1:57 PM
90LifeBook P7000 Notebook – Section EightP7010.book  Page 90  Monday, December 20, 2004  1:57 PM
91Regulatory InformationRegulatory InformationNOTICEChanges or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.FCC NOTICESNotice to Users of Radios and TelevisionThese limits are designed to provide reasonable protec-tion against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic-ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:nReorient or relocate the receiving antenna.nIncrease the separation between the equipment and receiver.nConnect the equipment into an outlet that is on a different circuit than the receiver.nConsult the dealer or an experienced radio/TVtechnician for help.Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Notice to Users of the US Telephone NetworkThis equipment (FMD MBH7MD33 Modem) complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this infor-mation or number must be provided to the telephone company.This equipment is designed to be connected to the tele-phone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.The ringer equivalent number (REN) of this equipment is 0.0B as shown on the label. The REN is used to deter-mine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local tele-phone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facili-ties, equipment, operations or procedures that could effect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to main-tain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commis-sion or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equip-ment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such busi-ness, other entity, or individual.P7010.book  Page 91  Monday, December 20, 2004  1:57 PM
92LifeBook P7000 Notebook - Section EightDOC (INDUSTRY CANADA) NOTICESNotice to Users of Radios and TelevisionThis Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.Notice to Users of the Canadian Telephone Network NOTICE: This equipment (Modem FMD MBH7MD33) meets the applicable Industry Canada Terminal Equip-ment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indi-cating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecom-munication company cause to request the user to disconnect the equipment from the telephone line.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equiva-lence Numbers of all the devices does not exceed five.Avis Aux Utilisateurs Du Réseau Téléphonique CanadienAVIS: Le présent matériel (FMD MBH7MD33 Modem) est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal. Cette confor-mité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformé-ment à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel. Avant de connecter cet équipement à une ligne télépho-nique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécom-munications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur décon-necte l’équipement de la ligne téléphonique.AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.0. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équiva-lence de la sonnerie de tous les dispositifs n’excède pas 5.For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appro-priate electric inspection authority or elec-trician. This may be particularly important in rural areas.Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du ser-vice d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont con-nectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connex-ions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales.P7010.book  Page 92  Monday, December 20, 2004  1:57 PM
939GlossaryP7010.book  Page 93  Monday, December 20, 2004  1:57 PM
94LifeBook P7000 Notebook – Section NineP7010.book  Page 94  Monday, December 20, 2004  1:57 PM
95GlossaryGlossaryAC AdapterA device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook.ACPIAdvanced Configuration and Power Interface. An industry specification for the efficient handling of power consumption in mobile computers. ACPI determines how a computer's BIOS, operating system, and periph-erals communicate with each other about power management. Active-Matrix DisplayA type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.ADSLAsymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines.APMAdvanced Power Management.Auto/Airline AdapterA device which converts the DC voltage from an auto-mobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook note-book.BIOSBasic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook notebook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.BitAn abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).bpsAn abbreviation for bits per second. Used to describe data transfer rates.BootTo start-up a computer and load its operating system from disk, ROM or other storage media into RAM.BusAn electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook.Byte8 bits of parallel binary information.Cache MemoryA block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.CardBusA faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.CD-ROMCompact disc read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.CMSCode Morphing Software. Crusoe processor software architecture that results in longer battery life. For more information on CMS, click on the Technology link on the refer to the Transmeta web site at: www.trans-meta.com.CommandAn instruction which you give your operating system. Example: run a particular application or format a floppy disk.ConfigurationThe combination of hardware and software that makes up your system and how it is allocated for use.DataThe information a system stores and processes.DCDirect current. A voltage or current that does not fluctuate periodically with time.Default ValueA pre programmed value to be used if you fail to set your own.DIMMDual-in-line memory module.DiskA spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.P7010.book  Page 95  Monday, December 20, 2004  1:57 PM
96LifeBook P7000 Notebook – Section NineDisk DriveThe hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.DisketteA floppy disk in a hard housing with a shutter.DMADirect Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.DMIDesktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software compo-nents, and peripherals.DOSDisk Operating System (MS-DOS is a Microsoft Disk Operating System).DriverA computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.ESDElectro-Static Discharge. The sudden discharge of elec-tricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.Extended MemoryAll memory more than the 640KB recognized by MS-DOS as system memory.FCCFederal Communication Commission.Floppy DiskA spinning platter of magnetic data storage media which is highly flexible.GBGigabyte.Hard driveA spinning platter of magnetic data storage media where the platter is very stiff.HexadecimalA decimal notation for the value of a 4 bit binary number. (0-9, A, B, C, D, E, F) Example: 2F in hexadecimal = 00101111 in binary = 47 in decimal.I/OInput/Output. Data entering and leaving your LifeBook notebook in electronic form.I/O PortThe connector and associated control circuits for data entering and leaving your LifeBook notebook in elec-tronic form.IDEIntelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.IEEE 1394The IEEE 1394 (also known as “Firewire” or “iLink”) standard allows you to connect devices that are compliant with IEEE standard 1394. This port is effec-tively a very fast communications port. This architecture is very good for transferring large files, such as those from digital cameras.IRQInterrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.KB Kilobyte.LANLocal Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.LCDLiquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.Lithium ion BatteryA type of rechargeable battery which has a high power-time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.MBMegabyte.Megahertz1,000,000 cycles per second.MemoryA repository for data and applications which is readily accessible to your LifeBook notebook CPU.MHzMegahertz.P7010.book  Page 96  Monday, December 20, 2004  1:57 PM
97GlossaryModemA contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.MonauralA system using one channel to process sound from all sources.NTSCNational TV Standards Commission. The standard for TV broadcast and reception for the USA.Operating SystemA group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of micro-processor in order to produce the desired results from that particular equipment.PartitionA block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.PCMCIAPCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.Peripheral DeviceA piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.Pitch (keyboard)The distance between the centers of the letter keys of a keyboard.PixelThe smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.POP3Post Office Protocol. Protocol that is used to retrieve email from a mail server.POSTPower On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your LifeBook notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded. PPPoEPoint to Point Protocol over Ethernet. A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line.ProgramAn integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.PS/2A series of personal computers which established a number of standards for connecting external devices such as keyboards and monitors.RAMRandom Access Memory. A hardware component of your LifeBook notebook that holds binary information (both program and data) as long as it has the proper power applied to it.RAM ModuleA printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.ResetThe act of reloading the operating system. A reset erases all information stored in RAM.RestartSee Reset.ResumeTo proceed after interruption. In your LifeBook note-book, this refers to returning to active operation after having been in one of the suspension states.ROMRead Only Memory. A form of memory in which infor-mation is stored by physically altering the material. Data stored in this way can not be changed by your LifeBook notebook and does not require power to maintain it.SDRAMSynchronous Dynamic Random Access Memory.Shadow RAMA technique of copying data or applications stored in ROM (Read Only Memory) into RAM (Random Access Memory) for access during actual operation. RAM is much faster to access than ROM, however ROM contents are not lost when power is removed. Shadowing allows permanently stored information to be rapidly accessed.SPDIFSony Philips Digital Interface. Technology that allows you to download digital audio data onto a MiniDisc recorder. P7010.book  Page 97  Monday, December 20, 2004  1:57 PM
98LifeBook P7000 Notebook – Section NineSSIDService Set Identifier. Specifies which network you are joining. Some systems allow you to specify any SSID as an option so you can join any network.Status IndicatorA display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard.Stereo (audio)A system using two channels to process sound from two different sources.Stroke (keyboard)The amount of travel of a key when it is pressed from resting to fully depressed.SuspendTo make inoperative for a period of time. Your LifeBook notebook uses various suspension states to reduce power consumption and prolong the charge of your battery.SVGASuper VGA. Standard that provides 800x600 pixel resolution and a palette of 16M colors.S-VideoSuper Video. A component video system for driving a TV or computer monitor.System ClockAn oscillator of fixed precise frequency which synchro-nizes the operation of the system and is counted to provide time of day and date.TFTThin Film Transistor. A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.ULUnderwriters Laboratories – An independent organiza-tion that tests and certifies the electrical safety of devices.USBUniversal Serial Bus. An external bus standard that allows for fast data transfer. A single USB port can be used to connect up to 127 peripheral devices, such as mice, modems, and scanners. USB 1.1 has a transfer speed of a maximum of 12Mb/s. USB 2.0 is much faster, transferring at up to 480Mb/s. USB 2.0 is backward-compatible to work with USB 1.1 devices.VGAVideo Graphics Array. A video display standard which provides resolutions of 720 x 400.VRAMVideo Random Access Memory. A memory dedicated to video display data and control.WEPWired Equivalent Privacy. WEP is a protocol for increasing privacy over wireless LANs. The protocol works by encrypting data while being transmitted over radio waves.WFMWired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.Wi-Fi CompatibleWi-Fi (Wireless Fidelity) identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guar-antees the interoperability of wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA website at: www.wirelessethernet.com.Write ProtectPrevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or direc-tory of floppy diskette or hard drive.XGAExtended graphics array. Standard that provides resolutions of 640x480 or 1024x764, supporting 64k colors.P7010.book  Page 98  Monday, December 20, 2004  1:57 PM
99Appendix AUsing the Fingerprint Sensor* * Optional DeviceP7010.book  Page 99  Monday, December 20, 2004  1:57 PM
100LifeBook P7000 Notebook – AppendixP7010.book  Page 100  Monday, December 20, 2004  1:57 PM
101Using the Fingerprint SensorFingerprint Sensor DeviceINTRODUCING THE OPTIONAL FINGERPRINT SENSOR DEVICEYour system may have an optional fingerprint sensor device in the location at which other models have a scroll button. (Figure 1) Figure A-1  Fingerprint sensorWith a fingerprint sensor, you can avoid having to enter a username and password every time you want to:■Log onto Windows■Recover from suspend mode■Cancel a password-protected screen saver■Log into homepages that require a username and pass-wordAfter you have “enrolled” - or registered - your finger-print, you can simply swipe your fingertip over the sensor for the system recognize you. The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and on-line passwords. OmniPass requires users to authenticate themselves using the fingerprint sensor before granting access to the Windows desktop. This device results in a secure authentication system for restricting access to your computer, applications, web sites, and other password-protected resources.OmniPass presents a convenient graphical user interface, through which you can securely manage passwords, users, and multiple identities for each user.GETTING STARTEDThis section guides you through the preparation of your system for the OmniPass fingerprint recognition application. You will be led through the OmniPass installation process. You will also be led through the procedure of enrolling your first user into OmniPass. INSTALLING OMNIPASSIf OmniPass has already been installed on your system, skip this section and go directly to “User Enrollment” on page 102. You can determine whether OmniPass has already been installed by checking to see if the following are present:■The presence of the gold key-shaped OmniPass icon in the system tray at the bottom right of the screen.■The presence of the Softex program group in the Programs group of the Start menuSystem RequirementsThe OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows:■Windows XP Home Edition or Windows XP Profes-sional operating system■At least 35 MB available hard disk spaceInstalling the OmniPass ApplicationIf OmniPass is already installed on your system, go to “User Enrollment” on page 102. Otherwise continue with this section on software installation.To install OmniPass on your system you must:1.  Insert the installation media for the OmniPass appli-cation into the appropriate drive. If you are installing from CD-ROM or DVD-ROM, you must find and launch the OmniPass installation program (setup.exe) from the media.2.  Follow the directions provided in the OmniPass installation program. Specify a location to which you would like OmniPass installed. It is recom-mended that you NOT install OmniPass in the root directory (e.g. C:\). 3.  Once OmniPass has completed installation you will be prompted to restart you system. Once your system has rebooted you will be able to use OmniPass. If you choose not to restart immediately after installation, OmniPass will not be available for use until the next reboot.Although the system may have a fingerprint sensor in place of a scroll button, the fingerprint sensor can be used for scrolling. Simply move your fingerprint over the sensor the same as you would use a scroll button. For installation, OmniPass requires that the user installing OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass installation.P7010.book  Page 101  Monday, December 20, 2004  1:57 PM
102LifeBook P7000 Notebook – AppendixThe installation program automatically places an icon (Softex OmniPass) in the Windows Control Panel as well as a golden key shaped icon in the taskbar. Verifying Information about OmniPassAfter you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system.To check the version information of OmniPass:1.  From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen),or,Click the Start button, select Settings, and click Control Panel (if you are using Windows XP you will see the Control Panel directly in the Start menu; click it, then click Switch to Classic View). Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear. If it does not appear, then the program is not properly installed,or,Click the Start button, select Programs, and from the submenu select the Softex program group, from that submenu click OmniPass Control Center.2. Select the About tab at the top of the OmniPass Control Panel. The About tab window appears with version information about OmniPass.Uninstalling OmniPassTo remove the OmniPass application from your system:1. Click Start on the Windows taskbar. Select Settings, and then Control Panel.2. Double-click Add/Remove Programs.3. Select OmniPass, and then click Change/Remove.4.  Follow the directions to uninstall the OmniPass application.5.  Once OmniPass has finished uninstalling, reboot your system when prompted.USER ENROLLMENTBefore you can use any OmniPass features you must first enroll a user into OmniPass.Master Password ConceptComputer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access. This can result in dozens of sets of creden-tials that you have to remember.During OmniPass user enrollment a "master password” is created for the enrolled user. This master password “replaces” all other passwords for sites you register with OmniPass. Example: A user, John, installs OmniPass on his system (his home computer) and enrolls an OmniPass user with username “John_01” and password “freq14”. He then goes to his webmail site to log onto his account. He inputs his webmail credentials as usual (username “John_02” and password “lifebook”), but instead of clicking [Submit], he directs OmniPass to Remember Password. Now whenever he returns to that site, OmniPass will prompt him to supply access credentials. John enters his OmniPass user credentials (“John_01” and “freq14”) in the OmniPass authentication prompt, and he is allowed into his webmail account. He can do this with as many web sites or password protected resources he likes, and he will gain access to all those sites with his OmniPass user credentials (“John_01” and “freq14”). This is assuming he is accessing those sites with the system onto which he enrolled his OmniPass user. OmniPass does not actually change the credentials of the password protected resource. If John were to go to an Internet cafe to access his webmail, he would need to enter his original webmail credentials (“John_02” and “lifebook”) to gain access. If he attempts his OmniPass user credentials on a system other than where he enrolled that OmniPass user, he will not gain access.Basic EnrollmentThe Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified other-wise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard.1. Click Enroll to proceed to username and password verification. By default, the OmniPass Enrollment Wizard enters the credentials of the currently logged in Windows user.2. Enter the password you use to log in to Windows. This will become the “master password” for this OmniPass user. In most cases, the Domain: value For uninstallation, OmniPass requires that the user uninstalling OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass uninstallation.The enrollment procedure assumes you have no hardware authentication devices or alternate storage locations that you wish to integrate with OmniPass. If you desire such functionality, consult the appropriate sections of this document.P7010.book  Page 102  Monday, December 20, 2004  1:57 PM
103Using the Fingerprint Sensorwill be your Windows computer name. In a corpo-rate environment, or when accessing corporate resources, the Domain: may not be your Windows computer name. Click [Next] to continue.3. In this step OmniPass captures your fingerprint. Refer to “Enrolling a Fingerprint” on page 103 for additional information.4. Next, choose how OmniPass notifies you of various events. We recommend you keep Taskbar Tips on Beginner mode taskbar tips and Audio Tips on at least Prompt with system beeps only until you get accustomed to how OmniPass operates. Click [Next] to proceed with user enrollment. You will then see a Congratulations screen indicating your completion of user enrollment.5. Click [Done] to exit the OmniPass Enrollment Wizard. You will be asked if you’d like to log in to OmniPass with your newly enrolled user; click [Yes].Enrolling a FingerprintEnrolling a fingerprint will increase the security of your system and streamline the authentication procedure. You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the User Settings area. Click Enroll Authentication Device and authenticate at the authentication prompt to start device enrollment.1. During initial user enrollment, you will be prompted to select the finger you wish to enroll. Fingers that have already been enrolled will be marked by a green check. The finger you select to enroll at this time will be marked by a red arrow. OmniPass will allow you re-enroll a finger. If you choose a finger that has already been enrolled and continue enrollment, OmniPass will enroll the fingerprint, overwriting the old fingerprint. Select a finger to enroll and click [Next].2. It is now time for OmniPass to capture your selected fingerprint. It may take a several capture attempts before OmniPass acquires your fingerprint. Should OmniPass fail to acquire your fingerprint, or if the capture screen times out, click [Back] to restart the fingerprint enrollment process. Your system has a “swipe” fingerprint sensor. A swipe sensor is small and resembles a skinny elon-gated rectangle. To capture a fingerprint, gently swipe or pull your fingertip over the sensor (starting at the second knuckle) towards yourself. Swiping too fast or too slow will result in a failed capture. The Choose Finger screen has a [Practice] button; click it to practice capturing your fingerprint. When you are comfortable with how your fingerprint is captured, proceed to enroll a finger.3.  Once OmniPass has successfully acquired the finger-print, the Ver if y Fi n g e r p r i n t  screen will automati-cally appear. To verify your enrolled fingerprint, place your fingertip on the sensor and hold it there as if you were having a fingerprint captured. Successful fingerprint verification will show a green fingerprint in the capture window and the text Ver i -fication Successful under the capture window.USING OMNIPASSYou are now ready to begin using OmniPass. Used regu-larly, OmniPass will streamline your authentications.Password ReplacementYou will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials. OmniPass can detect these prompts and you can teach OmniPass your login credentials. The next time you go to that website, you can authenticate with your fingerprint to gain access.OmniPass Authentication ToolbarAfter installing OmniPass and restarting, you will notice a dialog you have not seen before at Windows Logon. This is the OmniPass Authentication Toolbar, and it is displayed whenever the OmniPass authentication system is invoked. The OmniPass authentication system may be invoked frequently: during Windows Logon, during OmniPass Logon, when unlocking your workstation, when resuming from standby or hibernate, when unlocking a password-enabled screensaver, during pass-word replacement for remembered site or application logins, and more. When you see this toolbar, OmniPass is prompting you to authenticate.The Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not. When you click the icon for an unse-lected authentication method, the authentication prompt associated with that method is displayed.When prompted to authenticate, you must supply the appropriate credentials: an enrolled finger for the finger-print capture window or your master password for the master password prompt (the key icon).Remembering a PasswordOmniPass can remember any application, GUI, or pass-word protected resource that has a password prompt.Using the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint.P7010.book  Page 103  Monday, December 20, 2004  1:57 PM
104LifeBook P7000 Notebook – AppendixGo to a site that requires a login (username and pass-word), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login). Right-click the OmniPass system tray icon and select Remember Password from the submenu. The Windows arrow cursor will change to a golden key OmniPass cursor. Click this OmniPass cursor in the login prompt area, but do not click the [Login] or [Submit] button.Associating a Friendly NameAfter clicking the OmniPass key cursor near the login prompt, OmniPass will prompt you to enter a “friendly name” for this site. You should enter something that reminds you of the website, the company, or the service you are logging into. In its secure database, OmniPass associates this friendly name with this website.Additional Settings for Remembering a SiteWhen OmniPass prompts you to enter a “friendly name” you also have the opportunity to set how OmniPass authenticates you to this site. There are three effective settings for how OmniPass handles a remembered site.The default setting is Automatically click the “OK” or “Submit” button for this password protected site once the user is authenticated. With this setting, each time you navigate to this site OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass, you will automatically be logged into the site. Less secure is the option to Automatically enter this password protected site when it is activated. Do not prompt for authentication. Check the upper box to get this setting, and each time you navigate to this site OmniPass will log you into the site without prompting you to authenticate.If you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master pass-word or fingerprint authentication device. Once you have authenticated with OmniPass your credentials will be filled in to the site login prompt, but you will have to click the website [OK], [Submit], or [Login] button to gain access to the site. Click Finish to complete the remember password proce-dure. The site location, the credentials to access the site, and the OmniPass authentication settings for the site are now stored in the OmniPass secure database. The OmniPass authentication settings (Settings for this Pass-word Site) can always be changed in Vault Management.Logging in to a Remembered SiteWhether or not OmniPass prompts you to authenticate when you return to a remembered site is determined by Settings for this Password Site and can be changed in Vault Management. The following cases are applicable to using OmniPass to login to: Windows, remembered web sites, and all other password protected resources.With Master PasswordOnce you return to a site you have remembered with OmniPass, you may be presented with a master pass-word prompt. Enter your master password and you will be allowed into the site.Logging into Windows with a Fingerprint DeviceWhen logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.In Windows XP, your login options must be set either for classic login, or for fast user switching and logon screen to be enabled to use your fingerprint to log on to Windows. To change this go to Control Panel, select User Accounts and then click Change the way users log on or off. If your Windows screensaver is password protected, the fingerprint capture window will now appear next to screensaver password dialog during resume. You can authenticate to your screensaver pass-word prompt with your enrolled finger.Password ManagementOmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Vaul t  Manag e -ment; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Pass-words under Vault Settings. You will see the Manage Passwords interface, with a list of friendly names.This setting is more convenient in that whenever you go to a site remembered with this setting, you will bypass any authentication procedure and gain instant access to the site. But should you leave your system unattended with your OmniPass user logged in, anyone using your system can browse to your password protected sites and gain automatic access.If a machine is locked and OmniPass detects a different user logging back in with a fingerprint, the first user will be logged out and the second user logged in.P7010.book  Page 104  Monday, December 20, 2004  1:57 PM
105Using the Fingerprint SensorYou can view the credentials stored for any remembered website by highlighting the desired resource under Pass-word Protected Dialog and clicking Unmask Values. Should a password be reset, or an account expire, you can remove stored credentials from OmniPass. Highlight the desired resource under Password Protected Dialog and click Delete Page. You will be prompted to confirm the password deletion.The two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site.OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site. The exception to the above rule is the resetting of your Windows password. If your password is reset in Windows, then the next time you login to Windows, OmniPass will detect the password change and prompt you to “Update” or “Reconfirm” your password with OmniPass. Enter your new Windows password in the prompt(s) and click OK and your OmniPass "master password" will still be your Windows password.OmniPass User IdentitiesIdentities allow OmniPass users to have multiple accounts to the same site (e.g., bob@biblomail.com and boballen@biblomail.com). If OmniPass did not provide you identities, you would be limited to remembering one account per site.To create and manage identities, double-click the OmniPass key in the system tray. Click Vault  Manage -ment; OmniPass will prompt you to authenticate. Once you gain access to Vault Management, click Manage Identities under Vault Settings. You can only manage the identities of the currently logged in OmniPass userTo add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply]. You can now switch to the new identity and start remembering passwords.To delete an identity, highlight the identity you want to delete and click [Delete Identity], then click [Apply].To set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automati-cally be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password".Choosing User Identity during LoginTo choose your identity during login, type your user-name in the User Name: field. Press [Tab] and see that the Domain: field self-populates. Click the Password: field to bring the cursor to it, and you will see the pull-down menu in the Identity: field. Select the identity you wish to login as and then click OK to login.Switch User IdentityTo switch identities at any time, right-click the OmniPass system tray icon and click Switch User Iden-tity from the submenu. The Switch Identity dialog will appear. Select the desired identity and then click OK.Identities and Password ManagementOn the Manage Passwords interface of the Va u l t  Management tab of the OmniPass Control Center, there is a pull-down selection box labeled, Identity. This field lets you choose which identity you are managing pass-words for. When you select an identity here, only those password protected dialogs that are associated with that identity are shown. You can perform all the functions explained in “Password Management” on page 104.CONFIGURING OMNIPASSThis section gives an overview of both the Export/Import function and the OmniPass Control Center. Exporting and Importing UsersUsing the OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and any enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported. When you delete an identity, all of its associated remembered sites and password protected dialogs are lost.■You should periodically export your user profile and store it in a safe place. If anything happens to your system, you can import your OmniPass profile to a new system and have all your remem-bered settings and fingerprints instantly.■You don't forget the Windows login credentials when exporting. When you examine the importation, you are prompted for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain.P7010.book  Page 105  Monday, December 20, 2004  1:57 PM
106LifeBook P7000 Notebook – AppendixExporting an OmniPass User ProfileTo export a user, open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Exports an OmniPass user profile. OmniPass will prompt you to authenticate. Upon successfully authenti-cation, you must name the OmniPass user profile and decide where to save it. An .opi file is generated, and you should store a copy of it in a safe place.This .opi file contains all your user specific OmniPass data, and it is both encrypted and password protected. This user profile does NOT contain any of your encrypted data files.Importing an OmniPass User ProfileTo import an OmniPass user open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Imports a new user into OmniPass and then select OmniPass Import/Export File (*.opi) and click Next. OmniPass will then prompt you to browse for the file you had previously exported (.opi file). When you select the .opi file for importation, OmniPass will prompt you for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name.OmniPass will notify you if the user was successfully imported.Things to Know Regarding Import/Export■Assume you export a local Windows User profile from OmniPass. You want to import that profile to another machine that has OmniPass. Before you can import the profile, a Windows user with the same login cre-dentials must be created on the machine importing the profile.Example: I have a Windows user with the username “Tom” and the password “Sunshine” on my system. I have enrolled Tom into OmniPass and remembered passwords. I want to take all my passwords to new sys-tem. I export Tom’s OmniPass user profile. I go to my new system and using the Control Panel I create a user with the username "Tom" and the password "Sun-shine". I can now successfully import the OmniPass user data to the new system.■If you export an OmniPass-only user, you can import that user to any computer running OmniPass, pro-vided that a user with that name is not already enrolled in OmniPass. ■If you attempt to import a user profile who has the same name as a user already enrolled in OmniPass, the OmniPass import function will fail.OMNIPASS CONTROL CENTERThis section will serve to explain functions within the OmniPass Control Center that weren’t explained earlier. You can access the OmniPass Control Center any of three ways:■Double-click the golden OmniPass key shaped icon in the Windows taskbar (typically in the lower-right cor-ner of the desktop)■Click the Start button; select the Programs group; select the Softex program group; and click the OmniPass Control Center selection.■Open the Windows Control Panel (accessible via Start button --> Settings --> Control Panel) and double-click the Softex OmniPass icon.User ManagementThe User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/Export User functionality is documented in “Exporting and Importing Users” on page 105. Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard. The Enrollment Wizard is documented in “User Enrollment” on page 102. If you click Removes a user from OmniPass, OmniPass will prompt you to authenticate. Authenticate with the credentials (or enrolled fingerprint) of the user you wish to remove. OmniPass will prompt you to confirm user removal. Click OK to complete user removal.User SettingsThe User Settings tab has four interfaces: Audio Settings, Taskb a r  Ti ps, and Enrollment. User settings allow users to customize OmniPass to suit their individual prefer-ences. Under User Settings (Audio Settings and Ta s kb ar Tips) you can set how OmniPass notifies the user of OmniPass events (e.g., successful login, access denied, You cannot import a user into OmniPass if there already is a user with the same name enrolled in OmniPass. Removing a user will automatically destroy all OmniPass data associated with that user. All identities and credentials associated with the user will be lost.If you are sure about removing the user, we recommend you export the user profile.P7010.book  Page 106  Monday, December 20, 2004  1:57 PM
107Using the Fingerprint Sensoretc.). The details of each setting under the Audio Settings and Tas k bar Tips interfaces are self-explana-tory.The Enrollment interface allows you to enroll finger-prints. For the procedure to enroll and authentication device refer to Chapter 2.3. To enroll additional finger-prints, click Enroll Authentication Device, and authen-ticate with OmniPass. Select the fingerprint recognition device in the Select Authentication Device screen (it should already be marked by a green check if you have a finger enrolled) and click Next.System SettingsThe OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon.The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass. This setting is appropriate for an office setting or any setting where users must enter a username and password to log into a computer. This is the default setting.With the second option, Manually log on to OmniPass at startup, OmniPass will prompt you to login once you have logged on to Windows.With the third option, Do not log on to OmniPass at startup, OmniPass will not prompt for a user to be logged on.You can manually log on to OmniPass by right-clicking the OmniPass taskbar icon and clicking Log in User from the right-click menu.TROUBLESHOOTINGYou cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and passwordCannot add Windows users to OmniPassIf you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local secu-rity settings. You can do this by going to Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Network Access: Sharing and Security Model for Local Accounts. The correct setting should be Classic - Local Users Authen-ticate as Themselves.Cannot add a User with a Blank Password to OmniPassIf you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the proce-dure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure.Click Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Accounts: Limit local account use of blank pass-words to console login only. This setting should be set to Disabled.Dialog appears after OmniPass authentication during Windows LogonAfter installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box.This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). This could happen for any of the following reasons:■Your Windows password has changed■Your Windows account has been disabledIf you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password.Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.P7010.book  Page 107  Monday, December 20, 2004  1:57 PM
108LifeBook P7000 Notebook – AppendixP7010.book  Page 108  Monday, December 20, 2004  1:57 PM
109IndexIndexAACadapter  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23, 97plug adapters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81Anti-theft lock slot   . . . . . . . . . . . . . . . . . . . . . . . . . . .  10Auto Insert Notification  . . . . . . . . . . . . . . . . . . . . . . .  36Auto/Airline Adapter   . . . . . . . . . . . . . . . . . . . . . .  23, 97Automatically Downloading Driver Updates  . . . . . .  78BBattery   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31alarm   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31battery bay release button   . . . . . . . . . . . . . . . . . . .  11care  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82charging indicator . . . . . . . . . . . . . . . . . . . . . . . . . .  12conserving power   . . . . . . . . . . . . . . . . . . . . . . . . . .  27increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12lithium ion battery  . . . . . . . . . . . . . . . . . . . . . .  31, 98low   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31recharging   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32shorted  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32suspend mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31swapping   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32BIOS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  97guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26setup utility  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25Boot   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  97sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25Built-in Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . .  6CCache Memory   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  97Click Me!  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Cold-swap   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18Compact Flashcard slot  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8eject button  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8Configuration Label  . . . . . . . . . . . . . . . . . . . . . . . . . .  11Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . .  1Cursor control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15Cursor Keys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14DDCoutput cable   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23power jack  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 23Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44DIMM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42Disk care   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 24adjusting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24brightness   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24closing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24opening  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Display Timeout  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Dolby Headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Drivers and Application Restore CD   . . . . . . . . . . . . .77DVD/CD-RW drivecontrol panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35loading  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35software  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35tray release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36DVD-RAM   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34EError Messages   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75Extended Memory   . . . . . . . . . . . . . . . . . . . . . . . . . . . .98External Floppy Disk Drive  . . . . . . . . . . . . . . . . . . . . .33External Monitor Port  . . . . . . . . . . . . . . . . . . . . . . .9, 46FFDU  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78Fingerprint Sensor Device  . . . . . . . . . . . . . . . . . . . . .103enrolling a fingerprint  . . . . . . . . . . . . . . . . . . . . . .105getting started  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103installing OmniPass  . . . . . . . . . . . . . . . . . . . . . . . .103logging into a remembered site  . . . . . . . . . . . . . . .106OmniPass authentication toolbar  . . . . . . . . . . . . .105password replacement  . . . . . . . . . . . . . . . . . . . . . .105remembering a password . . . . . . . . . . . . . . . . . . . .105uninstalling OmniPass  . . . . . . . . . . . . . . . . . . . . . .104user enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . .104using OmniPass   . . . . . . . . . . . . . . . . . . . . . . . . . . .105Firewire   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 45P7010.book  Page 109  Monday, December 20, 2004  1:57 PM
110LifeBook P7000 NotebookFlexible bay   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8, 18cold-swapping  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18hot-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18release latch  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18Floppy Diskejecting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33formatting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33initializing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33loading  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33preparing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33write protect   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33Floppy Disk Drivecare  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82Fujitsu Driver Update utility  . . . . . . . . . . . . . . . . . . .  78Fujitsu HotKey Utility   . . . . . . . . . . . . . . . . . . . . . . . .  89Fujitsu LifeBookcare and maintenance . . . . . . . . . . . . . . . . . . . . . . .  81traveling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81Function KeyF10  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14F3   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14F4   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14F5   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14F6   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14F7   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14F8   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14F9   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14Fn  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14HHard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . .  28Hard Disk/CD Access Indicator . . . . . . . . . . . . . . . . .  12Headphone Jack   . . . . . . . . . . . . . . . . . . . . . . . . . . .  9, 45Hibernation Feature  . . . . . . . . . . . . . . . . . . . . . . . . . .  27disable/enable   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28Hot-swapping   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19IIEEE 1394 port . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9, 45IndicatorsCaps Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6Num Lock   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6Scroll Lock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6Integrated Wireless LAN   . . . . . . . . . . . . . . . . . . . . . .  47Internal LAN port  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44KKeyboard  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6, 13cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13key indicator lights  . . . . . . . . . . . . . . . . . . . . . . . . . .13numeric keypad   . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Windows keys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13windows keys   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13LLAN (RJ-45) port  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Lithium ion Battery   . . . . . . . . . . . . . . . . . . . . . . . . . . .11MMemorycapacity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43installing   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43Memory Module Cover  . . . . . . . . . . . . . . . . . . . . . . . .11Memory Stick/SD Card   . . . . . . . . . . . . . . . . . . . . . . . . .6installing   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41slot  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6, 40Memory Upgrade Module  . . . . . . . . . . . . . . . . . . . . . .42Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 46Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8port   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44result codes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76Modular Devices  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18installing   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18NNumeric Keypad  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13OOptical Digitalaudio connector  . . . . . . . . . . . . . . . . . . . . . . . . . . . .46audio-out jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Optical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83DVD/CD-RW combo   . . . . . . . . . . . . . . . . . . . . . . .34emergency tray release  . . . . . . . . . . . . . . . . . . . . . . .36software  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34P7010.book  Page 110  Monday, December 20, 2004  1:57 PM
111IndexPPC Cardcare  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  83eject button  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37, 38removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37, 39slot   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8Port Access Doors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9POST   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  75, 99error messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  75PowerAC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23auto/airline adapter   . . . . . . . . . . . . . . . . . . . . . . . .  23management   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27off  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28sources  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23Power Management   . . . . . . . . . . . . . . . . . . . . . . .  27, 28Power On  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25Power On Self Test   . . . . . . . . . . . . . . . . . . . . . . . . . . .  75Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . .  89Adobe Acrobat Reader  . . . . . . . . . . . . . . . . . . . . . .  89Earthlink 5.0   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  89manuals  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  89Netscape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  89Norton AntiVirus 2004   . . . . . . . . . . . . . . . . . . . . .  89Quicken New User Edition   . . . . . . . . . . . . . . . . . .  89tutorials  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  89Pre-installed Softwarerestoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  99RRegistration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26Regulatory Information  . . . . . . . . . . . . . . . . . . . . . . .  91Re-Installing Individual Drivers and Applications   .  77Restarting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28Restoring software . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77Restoring the Factory Image   . . . . . . . . . . . . . . . . . . .  77RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8, 44RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9, 44SSD Cardinstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  40removing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41SDRAM   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  42Secure Digital Cardremoving  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41Serial Port   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87audio   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87device ports  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88dimensions and weight   . . . . . . . . . . . . . . . . . . . . . .88environmental requirements . . . . . . . . . . . . . . . . . .88features   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87keyboard  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88mass storage device options . . . . . . . . . . . . . . . . . . .87memory  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87microprocessor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87MS Works  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89popular accessories . . . . . . . . . . . . . . . . . . . . . . . . . .88power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . .7, 12Stereo Speakers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Suspend  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27, 100Suspend/Resume/Power On Button  . . . . . . . . . . . .7, 27S-Video Out Port   . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 45Swapping batteries  . . . . . . . . . . . . . . . . . . . . . . . . . . . .32System Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . .87TTouchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15controls  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16double-clicking  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16pointing device  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6scroll button  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6scrolling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67battery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71built-in speakers  . . . . . . . . . . . . . . . . . . . . . . . . . . . .68CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68display panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73DVD/CD-RW drive  . . . . . . . . . . . . . . . . . . . . . . . . .68hard disk drive   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69identifying the problem  . . . . . . . . . . . . . . . . . . . . . .67keyboard  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69memory  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69PC card   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71, 72USB   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70Troubleshooting Table  . . . . . . . . . . . . . . . . . . . . . . . . .68P7010.book  Page 111  Monday, December 20, 2004  1:57 PM

Navigation menu