Fujitsu Client Computing WL0010 WM3945ABG GOLAN INTEL WLAN IN FUJITSU NOTEBOOKS User Manual 3

Fujitsu Limited WM3945ABG GOLAN INTEL WLAN IN FUJITSU NOTEBOOKS 3

Contents

USER MANUAL 3

FCC ID: EJE-WL0010 (IC: 337J-WL0010) Report No. M060108_Cert_WM3945ABG_DTS EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M060108_Cert_WM3945ABG_DTS APPENDIX I2 FUJITSU NOTEBOOK USER MANUAL (part 3)
696Care and MaintenanceS7020.book Page 69 Friday, May 13, 2005 3:49 PM
70LifeBook S7000 NotebookS7020.book Page 70 Friday, May 13, 2005 3:49 PM
71Care and MaintenanceCare and MaintenanceIf you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices.Caring for your LifeBook notebook■Your LifeBook notebook is a durable but sensitive electronic device. Treat it with respect and care.■Make a habit of transporting it in a suitable carrying case. To protect your notebook from damage and to optimize system performance, be sure to keep all air all vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used. ■Do not operate the notebook in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.■Do not attempt to service the computer yourself. Always follow installation instructions closely.■Keep it away from food and beverages.■If you accidentally spill liquid on your LifeBook note-book:1. Turn it off.2. Position it so that the liquid can run out.3. Let it dry out for 24 hours, or longer if needed.4. If your notebook will not boot after it has dried out, call your support representative.■Do not use your Fujitsu LifeBook notebook in a wet environment (near a bathtub, swimming pool).■Always use the AC adapter and batteries that are approved for your notebook.■Avoid exposure to sand, dust and other environmental hazards.■Do not expose your notebook to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your notebook.■Keep the covers closed on the connectors and slots when they are not in use.■Do not put heavy or sharp objects on the computer.■If you are carrying your LifeBook notebook in a brief-case, or any other carrying case, make sure that there are no objects in the case pressing on the lid.■Never position your notebook such that the optical drive is supporting the weight of the notebook. ■Do not drop your notebook.■Do not touch the screen with any sharp objects. Cleaning your LifeBook notebook■Always disconnect the power plug. (Pull the plug, not the cord.)■Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.■Use a soft cloth to remove dust from the screen. Never use glass cleaners.Storing your LifeBook notebook■If storing your notebook for a month or longer, turn your LifeBook notebook off, fully charge the battery(s), then remove and store all Lithium ion batteries.■Store your notebook and batteries separately. If you store your LifeBook with a battery installed, the battery will discharge, and battery life will be reduced. In addi-tion, a faulty battery might damage your LifeBook.■Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between 13ºF (-25ºC) and 140ºF (60ºC).Traveling with your LifeBook notebook■Do not transport your notebook while it is turned on. ■It is recommended that you carry your notebook with you while traveling, rather than checking it in as bag-gage.■Always bring your System Recovery CD that came with your notebook when you travel. If you experience sys-tem software problems while traveling, you may need it to correct any problems. ■Never put your notebook through a metal detector. Have your notebook hand-inspected by security per-sonnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel. Secu-rity officials may require you to turn your notebook On. Make sure you have a charged battery on hand. ■When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand-inspected by Electrical equipment may be hazardous if misused. Operations of this product or simi-lar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.S7020.book Page 71 Friday, May 13, 2005 3:49 PM
72LifeBook S7000 Notebooksecurity personnel. You can however, put your hard drive through a properly tuned X-ray machine. ■Take the necessary plug adapters if you're traveling over-seas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.BATTERIESCaring for your Batteries■Always handle batteries carefully.■Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.■Do not drop, puncture, disassemble, mutilate or incin-erate the battery.■Recharge batteries only as described in this manual and only in ventilated areas.■Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.■Do not leave a battery in storage for longer than 6 months without recharging it.Increasing Battery Life■Power your LifeBook notebook through the AC or optional auto/airline adapter whenever possible.■If your notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.■Keep brightness to the lowest level comfortable.■Set the power management for maximum battery life.■Put your notebook in Suspend mode when it is turned on and you are not actually using it.■Limit your media drive access.■Disable the Media Player auto insert notification function.■Always use fully charged batteries.■Eject PCMCIATM cards when not in use.FLOPPY DISKS AND DRIVESCaring for your Floppy Disks■Avoid using the floppy disks in damp and dusty locations.■Never store a floppy disk near a magnet or magnetic field.■Do not use a pencil or an eraser on a disk or disk label.■Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).■Do not touch the exposed part of the disk behind the metal shutter.■Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy disk drive or disk.■Never disassemble your floppy disk drive.MEDIA CARECaring for your Media (DVD/CD/CD-R)Media discs are precision devices and will function reli-ably if given reasonable care.■Always store your media disc in its case when it is not in use.■Always handle discs by the edges and avoid touching the surface.■Avoid storing any media discs in extreme temperatures.■Do not bend media discs or set heavy objects on them.■Do not spill liquids on media discs.■Do not scratch media discs.Outlet Type LocationUnited States, Canada,parts of Latin America,Mexico, Japan, Korea,the Philippines, TaiwanRussia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South AsiaUnited Kingdom, Ireland, Malaysia, Singapore, parts of AfricaChina, Australia,New ZealandS7020.book Page 72 Friday, May 13, 2005 3:49 PM
73Care and Maintenance■Do not get dust on media discs.■Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.■If a media disc is subjected to a sudden change in tem-perature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry media discs.■If a disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.Caring for your Optical DriveYour optical drive is durable but you must treat it with care. Please pay attention to the following points:■The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.■Avoid using or storing the drive where it will be exposed to extreme temperatures.■Avoid using or storing the drive where it is damp or dusty.■Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.■Avoid using or storing the drive where it will be subjected to shock or vibration.■Do not disassemble or dismantle the optical drive.■Use of a commercially available lens cleaner is recommended for regular maintenance of your drive.PC CARDS/EXPRESSCARDSCaring for your PC Cards and ExpressCards PC Cards and ExpressCards are durable, but you must treat them with care. The documentation supplied with your card will provide specific information, but you should pay attention to the following points:■To keep out dust and dirt, store cards in their protective sleeves when they are not installed in your LifeBook notebook.■Avoid prolonged exposure to direct sunlight orexcessive heat.■Keep the cards dry.■Do not flex or bend the cards, and do not place heavy objects on top of them.■Do not force cards into the slot.■Avoid dropping cards, or subjecting them to excessive vibration.S7020.book Page 73 Friday, May 13, 2005 3:49 PM
74LifeBook S7000 NotebookS7020.book Page 74 Friday, May 13, 2005 3:49 PM
757SpecificationsS7020.book Page 75 Friday, May 13, 2005 3:49 PM
76LifeBook S7000 NotebookS7020.book Page 76 Friday, May 13, 2005 3:49 PM
77SpecificationsSpecificationsThis section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook. Spec-ifications of particular configurations will vary.CONFIGURATION LABELThere is a configuration label located on the bottom of your LifeBook notebook. (See figure 2-8 on page 10 for location) This label contains specific information regarding the options you’ve chosen for your notebook. Following is an example label and information on how to read your own configuration label.Figure 7-1 Configuration LabelMICROPROCESSORIntel Core Duo processor (Refer to the system label to determine the speed of your processor).CHIPSETIntel 945GMMEMORYSystem MemoryDDR2 533 MHz dual-channel* SDRAM memory module. 256 MB pre-installed in one DIMM slot; one open DIMM slot available for upgrade. Upgradeable to 2 GB of total memory (1 GB x 2)* Dual-channel data transfer is enabled automatically only when using two DDR2 533 memory modules of the same capacity together.Cache Memory2 MB L2 on-dieVIDEOBuilt-in color flat-panel TFT active matrix LCD display with simultaneous display capabilityVideo Color and ResolutionDepending upon your system configuration, you have one of the following displays: 14.1” Crystal View TFT XGAInternal: Up to 1024 x 768 pixel resolution, 16M colorsExternal: Up to 1600 x 1200 pixel resolution, 16M colorsSimultaneous Video: Up to 1024 x 768, 16M colors. XGA, SVGA and VGA compatible14.1” TFT SXGA+Internal: Up to 1400 x 1050 pixel resolution, 16M colorsExternal: Up to 1600 x 1200 pixel resolution, 16M colorsSimultaneous Video: Up to 1400 x 1050, 16M colors. XGA, SVGA and VGA compatibleVideo RAMIntel® Graphics Media Accelerator 900 with PCI-Express 16x interface; up to 128 MB shared video memory using Dynamic Video Memory Technology (DVMT). AUDIORealtek ALC260 codec with 2-channel High Definition (HD) audioStereo line-out/headphone jack, 3.5 mm, 1 Vrms or less, minimum impedance 32 OhmsStereo microphone/line-in jack, 3.5 mm, 100 mVp-p or less, minimum impedance 10K OhmsTwo built-in stereo speakers, 16 mm diameterMASS STORAGE DEVICE OPTIONSHard Drive80 GB, 60 GB, or 40 GB Serial ATA hard drive; 5400 rpm, 1.5 Gb/s transfer rateMedia PlayerDepending upon the configuration of your system, one of the following is installed.DVD-ROM Drive (8x DVD-R, 24 x CD-ROM), or,Combo DVD/CD-RW Drive (modular 8x maximum DVD/24x maximum write, 10x maximum rewrite, 24x maximum read CD-RW combo drive), or, AUUXXXXXXXXXXXXXS 7110, P M 740, 14C VXG A, X P P, 60G , 256M, LAN/W LANP /N: F P C P /N: FP C MXXXXXOperating Hard Drive Configuration IDPart NumberProcessorModel # Screen Size MemorySystemCommunicationsS7020.book Page 77 Friday, May 13, 2005 3:49 PM
78LifeBook S7000 Notebook■Dual-Layer Multi-Format DVD Writer (modular 8x DVD-R, 4x DVD-RW, 8x DVD+R, 4x DVD+RW, 2.4x DL +R, 3x DVD-RAM, 8x DVD-ROM, 24x CD-R, 10x CD-RW, 24x CD-ROM)FEATURESIntegrated Pointing Device■Touchpad pointing device with scroll button■Optional Quick Point cursor control button■Optional fingerprint swipe sensorCommunicationsModem: Internal V.90 standard 56K fax/modem(ITU V.90, 56K data, 14.4K fax) Gigabit LAN: Internal wired 10Base-T/100Base-Tx/1000Base-T/Tx Ethernet LANWireless LAN: Certain configurations of the Lifebook S7000 notebook have an optional Wireless LAN device installed. If you have an IntelPRO device installed, your system is classified as a Centrino product. If you have a Wireless LAN device other than IntelPRO installed, your system is classified as a Pentium M product. (For additional information about the Wireless LAN device, refer to the Wireless LAN User’s Guide on page 91).■Integrated Intel PRO/Wireless 2915ABG Network Connections (802.11a+b/g*) with Antenna On/Off switch (available in LifeBook S7020 model), or,■Integrated Atheros Super AG Wireless LAN (802.11a/b/g*) with Antenna On/Off switch (available in Life-Book S7020D model)■Optional Bluetooth device for wireless personal area network communication* Operates at 2.4 GHz and 5.0 GHz; communications range may vary, depending upon environment.LifeBook Security/Application PanelThe Application Launcher buttons on your LifeBook notebook default to the following applications:Theft Prevention LockLock slot for use with security restraint systems. The Kensington locking system is recommended.DEVICE PORTSOn the LifeBook notebook:■PC Card slot for Type I or Type II card: PCMCIA Standard 2.1 with CardBus support■ExpressCard slot for one ExpressCard 54/34■One 15-pin D-SUB connector for VGA external monitor (see Display specifications)■Three USB 2.0 (Universal Serial Bus) connectors forinput/output devices ■One IEEE 1394 (4-pin type) jack■One modular modem (RJ-11) connector■One LAN (RJ-45) connector ■One stereo headphone/line-out jack. (See Audio speci-fications)■One stereo microphone/line-in jack. (See Audio specifi-cations)■Embedded Smart Card Reader (requires optional third-party application and holder)■S-Video Out jack■Wireless LAN antenna with pre-installed on/off switch■Optional Bluetooth module with antennaOn the Optional Port Replicator:■One 6-pin mini DIN PS/2 compatible connectors for external keyboard or mouse■One 25-pin D-SUB connector for parallel input/output devices; Bi-directional, output only or ECP■One 15-pin D-SUB connector for VGA external monitor (see Display specifications)■One 9-pin D-SUB connector for RS-232C serialinput/output devices■Four USB 2.0 (Universal Serial Bus) connectors for input/output devices■One LAN (RJ-45) connector ■One DC In connector■One microphone In jack■One headphone jack■One Digital Video (DVI-D) 24-pin, female interface■One power/suspend/resume buttonKEYBOARDBuilt-in keyboard with all functions of 101 key PS/2 compatible keyboards.■Total number of keys: 84■Function keys: F1 through F12■Feature extension key: Fn■Two Windows keys: one Start key, one application key ■Key pitch: 19 mm■Key stroke: 3 mm■Built-in Touchpad pointing device with left and right buttons and scroll button.■Built-in Palm Rest■Optional Quick Point cursor control buttonExternal Keyboard SupportUSB or PS/2-compatible (PS/2 compatible with Port Replicator only)Table 7-1 Application Launcher DefaultsButtonLabelButtonFunction Default Application1 Application A Notepad2 Application B Calculator3 Internet Internet Explorer4 E-Mail Microsoft Outlook or Outlook ExpressS7020.book Page 78 Friday, May 13, 2005 3:49 PM
79SpecificationsExternal Mouse SupportUSB or PS/2-compatible (PS/2 compatible with Port Replicator only)POWERBatteriesOne 6-cell Lithium ion battery, rechargeable, 10.8V, 4800 mAh, 51.8 Wh Optional Flexible Bay battery: 6-cell Lithium ion battery, rechargeable, 10.8V, 3800 mAh, 41.0 WhAC AdapterAutosensing 100-240V AC, supplying 19V DC, 3.15A, 60W to the LifeBook notebook, Fujitsu Model FPCAC46AP, which includes an AC cable.Power ManagementConforms to ACPI (Advanced Configuration and Power Interface).DIMENSIONS AND WEIGHTOverall DimensionsApproximately 12.05"(w) x 9.72"(d) x 1.0”/1.3”(h) (306 mm x 247 mm x 25.4/33.0 mm)WeightsApproximately 3.85 lbs (1.75 kg) with battery and weight saver.Approximately 4.3 lbs (1.95 kg) with battery and DVD/CD-RW Combo drive.ENVIRONMENTAL REQUIREMENTSTemper atureOperating: 41° to 95° F (5° to 35° C)Non-operating: 5° to 140° F (–15° to 60° C)HumidityOperating: 20% to 85%, relative, non-condensingNon-operating; 8% to 85%, relative, non-condensingPOPULAR ACCESSORIESFor ordering or additional information on Fujitsu accessories please visit our Web site atus.fujitsu.com/computers or call 1-877-372-3473.Memory Upgrades■256 MB, 512 MB, and 1 GB SDRAM modulesDocking■Port ReplicatorPower■Main Lithium ion battery■Battery Charger■Auto/Airline Adapter■AC AdapterPC Cards■Wireless PC Card ■4-in-1 Media Card Adapter■Compact Flash Media Card AdapterAdditional Accessories■Wireless Keyboard and Mouse■External USB Floppy Disk Drive■Presentation Audio System■Tele Ad a pt 1 6' Te leC or d■Notebook Guardian Lock■IBM Modem SaverCarrying Cases■Diplomat■Backpack■Director■MobileMax Wheeled CasePRE-INSTALLED SOFTWAREDepending on your pre-installed operating system, your Fujitsu LifeBook notebook comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software, virus protection software and Power Management software. The following list indicates the pre-installed software associated with your system.■Adobe Acrobat Reader■Fujitsu HotKey/Fujitsu BatteryAid■LifeBook Security/Application Panel■Symantec Norton AntiVirus 2004 (90-day free trial)■Quicken 2005 New User Edition■Fujitsu Driver Update UtilityDepending upon your system configuration, you may receive one of the following:■Microsoft Works 8.0■Microsoft Office 2003 Small Business EditionLEARNING ABOUT YOUR SOFTWARETutorialsAll operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application.ManualsIncluded with your notebook you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included, are avail-able online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications.Adobe Acrobat ReaderThe Adobe Acrobat Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms. Fujitsu HotKeyFujitsu HotKey allows you to control the display bright-ness of your notebook in order to maximize battery life. S7020.book Page 79 Friday, May 13, 2005 3:49 PM
80LifeBook S7000 NotebookQuicken 2005 New User EditionQuicken 2005 New User Edition by Intuit is a personal money management program. It has features such as portfolio management, account registries, on-line banking and bill paying features. This application is for new users who are using Quicken software for the first time. Full version upgrade information is available on line.LifeBook Security/Application Panel SoftwareYour LifeBook notebook is pre-installed with software utilities that let you operate and configure your LifeBook Security/Application Panel. The Security Panel portion allows for password protection while the system is off or in Suspend mode. The Security Panel utilities are found under the Start menu, under Programs, then under LifeBook Security Panel. The Application Panel utilities are found under the Start menu, Settings/Control Panel, then Application Panel. To open the CD Player and Application Panel Help, select Start, Programs, LifeBook Application Panel.Norton AntiVirus 2005Your system is pre-installed with a free 90-day trial version of Symantec’s Norton AntiVirus™ 2005. Norton AntiVirus is a program designed to protect your Life-Book notebook from computer viruses. It assists in the protection of the data currently residing on your hard disk from destruction or contamination. The 90-day trial version is activated upon your acceptance of soft-ware license agreement. After 90 days, it will be neces-sary to purchase a subscription from Symantec to download latest virus definitions. S7020.book Page 80 Friday, May 13, 2005 3:49 PM
818GlossaryS7020.book Page 81 Friday, May 13, 2005 3:49 PM
82LifeBook S7000 NotebookS7020.book Page 82 Friday, May 13, 2005 3:49 PM
83GlossaryGlossaryAC AdapterA device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook.ACPIAdvanced Configuration and Power InterfaceActive-Matrix DisplayA type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.AdHocA name of a wireless LAN configuration.It is a type of communication using wireless cards only.Another type of communication is called Infrastructure (using a wireless card and an access point).ADSLAsymmetric Digital Subscriber LineTechnology for transporting high bit-rate services over ordinary phone lines.AGPAccelerated Graphics PortGraphics port specifically designed for graphics-inten-sive devices, such as video cards and 3D accelerators.Auto/Airline AdapterA device which converts the DC voltage from an auto-mobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook note-book.BIOSBasic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook notebook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.BitAn abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).bpsAn abbreviation for bits per second. Used to describe data transfer rates.BootTo start-up a computer and load its operating system from disk, ROM or other storage media into RAM.BusAn electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook.Byte8 bits of parallel binary information.Cache MemoryA block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.CardBusA faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.CD-ROMCompact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.ChannelA radio frequency band used for communication between wireless cards and access points.CMOS RAMComplementary metal oxide semiconductor random access memory. This is a technology for manufacturing random access memory which requires very low levels of power to operate.COM PortAbbreviation for communication port. This is your serial interface connection.CommandAn instruction which you give your operating system. Example: run a particular application or format a floppy disk.ConfigurationThe combination of hardware and software that makes up your system and how it is allocated for use.CRTCathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It S7020.book Page 83 Friday, May 13, 2005 3:49 PM
84LifeBook S7000 Notebookproduces a visual image by varying the position and intensity of the beam.DataThe information a system stores and processes.DCDirect current. A voltage or current that does not fluctuate periodically with time.Default ValueA pre programmed value to be used if you fail to set your own.DHCP Dynamic Host Configuration ProtocolA protocol used to automatically acquire parameters required for the communication, such as IP address.The sender of IP address is called a DHCP server, and the receiver is called a DHCP client.DIMMDual-in-line memory module.DiskA spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.Disk DriveThe hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.DisketteA floppy disk in a hard housing with a shutter.DMADirect Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.DMIDesktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software compo-nents, and peripherals.DNS Domain Name SystemA function to control the association between the IP address and the name assigned to the computer.If you do not know the IP address but if you know the computer name, you can still communicate to that computer.DOSDisk Operating System (MS-DOS is a Microsoft Disk Operating System).DriverA computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.DVMTDynamic Video Memory TechnologyA video memory architecture that increases the efficiency of the motherboard by using innovative memory utilization and direct AGP.ECPExtended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices.Encryption Key (Network Key)Data encryption key used to encrypt message text and for computing message integrity checks. Data encryp-tion protects data from unauthorized viewing.This device uses the same encryption key to encode and decode the data, and the identical encryption key is required between the sender and receiver.ESDElectro-Static Discharge. The sudden discharge of elec-tricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.Extended MemoryAll memory more than the 640KB recognized by MS-DOS as system memory.FCCFederal Communication Commission.Floppy DiskA spinning platter of magnetic data storage media which is highly flexible.GBGigabyte.S7020.book Page 84 Friday, May 13, 2005 3:49 PM
85GlossaryHard driveA spinning platter of magnetic data storage media where the platter is very stiff.I/OInput/Output. Data entering and leaving your notebook in electronic form.I/O PortThe connector and associated control circuits for data entering and leaving your notebook in electronic form.IDEIntelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.InfraredLight just beyond the red portion of the visible light spectrum which is invisible to humans.InfrastructureA name of a wireless LAN configuration. This type of communication uses an access point.Another type of communication is called AdHoc.IP AddressAn identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 1.160.10.240 could be an IP address. Within an isolated network, you can assign IP addresses at random as long as each one is unique. However, connecting a private network to the Internet requires using registered IP addresses (called Internet addresses) to avoid duplicates. The four numbers in an IP address are used in different ways to identify a particular network and a host on that network. Three regional Internet registries -- ARIN, RIPE NCC and APNIC -- assign Internet addresses from the following three classes. Class A - supports 16 million hosts on each of 126 networks Class B - supports 65,000 hosts on each of 16,000 networks Class C - supports 254 hosts on each of 2 million networks The number of unassigned Internet addresses is running out, so a new classless scheme called CIDR is gradually replacing the system based on classes A, B, and C and is tied to adoption of IPv6. (credit: webopedia.com)IRAn abbreviation for infrared.IrDAInfrared Data Association. An organization which produces standards for communication using infrared as the carrier.IRQInterrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.KB Kilobyte.LANLocal Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.LCDLiquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.Lithium ion BatteryA type of rechargeable battery which has a high power-time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.LPT PortLine Printer Port. A way of referring to parallel interface ports because historically line printers were the first and latter the most common device connected to parallel ports.MAC Address Media Access Control AddressA unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards. For Ethernet, frames are sent and received based on this address.MBMegabyte.S7020.book Page 85 Friday, May 13, 2005 3:49 PM
86LifeBook S7000 NotebookMegahertz1,000,000 cycles per second.MemoryA repository for data and applications which is readily accessible to your LifeBook notebook’s CPU.MHzMegahertz.MIDIMusical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers.ModemA contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.MonauralA system using one channel to process sound from all sources.MPU-401A standard for MIDI interfaces and connectors.MTUMaximum Transmission UnitThe maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large.Norton AntiVirusWeb-based software that protects you email, instant messages, and other files by removing viruses, worms, and Trojan horses.NTSCNational TV Standards Commission. The standard for TV broadcast and reception for the USA.Operating SystemA group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of micro-processor in order to produce the desired results from that particular equipment.PartitionA block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.PCIPeripheral Component Interconnect Self-configuring PC local bus. Designed by Intel, PCI has gained wide acceptance as a standard bus design.PCMCIAPCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.Peripheral DeviceA piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.Pitch (keyboard)The distance between the centers of the letter keys of a keyboard.PixelThe smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.POSTPower On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded. PPPoEPoint to Point Protocol over Ethernet.A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line.ProgramAn integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.ProtocolProcedures and rules use to send and receive data between computers.S7020.book Page 86 Friday, May 13, 2005 3:49 PM
87Glossary- Method of sending and receiving data- Process used to handle communication errorsConditions required for communication are organized in procedures for correct transfer of information.RAMRandom Access Memory. A hardware component of your LifeBook notebook that holds binary information (both program and data) as long as it has the proper power applied to it.RAM ModuleA printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.ResetThe act of reloading the operating system. A reset erases all information stored in RAM.RestartSee Reset.ResumeTo proceed after interruption. In your notebook this refers to returning to active operation after having been in one of the suspension states.ROMRead Only Memory. A form of memory in which infor-mation is stored by physically altering the material. Data stored in this way can not be changed by your notebook and does not require power to maintain it.SDRAMSynchronous Dynamic Random Access Memory.Serial PortA connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.SMARTSelf-Monitoring, Analysis and Reporting Technology (SMART) is an emerging technology that provides near-term failure predictions for hard drives. When SMART is enabled the hard drive monitors pre-determined drive attributes that are susceptible to degradation over time. If a failure is likely to occur, SMART makes a status report available so that the LifeBook notebook can prompt the user to back up the data on the drive. Natu-rally not all failures are predictable. SMART predict-ability is limited to those attributes which the drive can self-monitor. In those cases where SMART can give advance warning, a considerable amount of precious data can be saved.SRAMStatic random access memory. A specific technology of making RAM which does not require periodic data refreshing.SSIDService Set IdentifierSpecifies which network you are joining. Some systems allow you to specify any SSID as an option so you can join any network.StandbyTo make inoperative for a period of time. Your LifeBook notebook uses various suspension states to reduce power consumption and prolong the charge of your battery.Status IndicatorA display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard.Stereo (audio)A system using two channels to process sound from two different sources.SVGASuper VGA.S-VideoSuper Video. A component video system for driving a TV or computer monitor.System ClockAn oscillator of fixed precise frequency which synchro-nizes the operation of the system and is counted to provide time of day and date.TCP/IP Transmission Control Protocol/Internet Protocol.A standard Internet protocol that is most widely used.TFTThin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.ULUnderwriters Laboratories – An independent organiza-tion that tests and certifies the electrical safety of devices.S7020.book Page 87 Friday, May 13, 2005 3:49 PM
88LifeBook S7000 NotebookUSBUniversal Serial Bus.Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer.VGAVideo Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of personal computers.VRAMVideo Random Access Memory. A memory dedicated to video display data and control.WFMWired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.Wi-Fi CompatibleWi-Fi (Wireless Fidelity) Identifies that the product has passed the interoperability test, supplied by the WECA (Wireless Ethernet Compatibility Alliance), which guar-antees the interoperability of wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA Web site at: www.wirelessethernet.com.WLANWireless Local Area Network. A wireless interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.Write ProtectPrevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or direc-tory of floppy diskette or hard drive.XGAExtended VGA.Zip DriveA 100MB or 250MB read/write removable media disk drive.S7020.book Page 88 Friday, May 13, 2005 3:49 PM
89Regulatory InformationRegulatory InformationNOTICEChanges or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.FCC NOTICESNotice to Users of Radios and TelevisionThese limits are designed to provide reasonable protec-tion against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic-ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:nReorient or relocate the receiving antenna.nIncrease the separation between the equipment and receiver.nConnect the equipment into an outlet that is on a different circuit than the receiver.nConsult the dealer or an experienced radio/TVtechnician for help.Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Notice to Users of the US Telephone NetworkThis equipment complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this information or number must be provided to the telephone company.This equipment is designed to be connected to the tele-phone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.The ringer equivalent number (REN) of this equipment is 0.0B as shown on the label. The REN is used to deter-mine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local tele-phone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facili-ties, equipment, operations or procedures that could effect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to main-tain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commis-sion or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equip-ment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such busi-ness, other entity, or individual.S7020.book Page 89 Friday, May 13, 2005 3:49 PM
90LifeBook S7000 NotebookDOC (INDUSTRY CANADA) NOTICESNotice to Users of Radios and TelevisionThis Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signi-fies that registration was performed based on a Declara-tion of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecom-munication company cause to request the user to disconnect the equipment from the telephone line.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equiva-lence Numbers of all the devices does not exceed five.Avis Aux Utilisateurs Du Réseau Téléphonique CanadienAVIS: Le présent matériel est conforme aux spécifica-tions techniques d’Industrie Canada applicables au matériel terminal. Cette conformité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel. Avant de connecter cet équipement à une ligne télépho-nique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécom-munications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur décon-necte l’équipement de la ligne téléphonique.AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.0. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équiva-lence de la sonnerie de tous les dispositifs n’excède pas 5.For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appro-priate electric inspection authority or elec-trician. This may be particularly important in rural areas.Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du ser-vice d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont con-nectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connex-ions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales.S7020.book Page 90 Friday, May 13, 2005 3:49 PM
91Appendix AIntegrated WirelessLAN* User’s Guide* Optional deviceS7020.book Page 91 Friday, May 13, 2005 3:49 PM
92LifeBook S7000 NotebookS7020.book Page 92 Friday, May 13, 2005 3:49 PM
93WIreless LAN User’s Guide FCC REGULATORY INFORMATIONPlease note the following regulatory information related to the wireless LAN device.Regulatory Notes and StatementsWireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wire-less LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:On board an airplane, orIn an explosive environment, orIn situations where the interference risk to other devices or services is perceived or identified as harmful.In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment.Regulatory Information/DisclaimersInstallation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its autho-rized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operating in conjunction with any other antenna or transmitter.For operation within 5.15~5.25 GHz frequency range, the device is restricted to indoor environments, and the antenna of this device must be integral.Federal Communications Commission statementThis device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.FCC Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the distance between the equipment and the receiver.3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.4. Consult the dealer or an experienced radio/TV technician for help.FCC Radio Frequency Exposure statementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the Wireless LANantennas and yourbody. The WLAN antenna is located on the left and ends of the top edge of the LCD screen.The transmitters in this device must not be co-located or oper-ated in conjunction with any other antenna or transmitter.Export restrictionsThis product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment.Canadian NoticeTo prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.High power radars are allocated as the primary users of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LELAN (license-exempt LAN) devices operating in these bands.S7020.book Page 93 Friday, May 13, 2005 3:49 PMright
94LifeBook S7000 Series Notebook - AppendixBefore Using the Wireless LANThis manual describes the procedures required to prop-erly setup and configure the integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Keep this manual in a safe place for future reference.Wireless LAN Devices Covered by this DocumentThis document is applicable to systems containing one of the following two devices. Most of the procedures are identical. Sections that differ between the three devices have been noted in the text:Intel PRO/Wireless 3945ABG (WM3945ABG) Network Connections (802.11a+b/g): Available on LifeBook S7110 notebook modelCharacteristics of the WLAN DeviceThe WLAN device is a Mini-PCI card attached to the main board of the mobile computer. The WLAN devices operate in license-free RF bands, therefore eliminating the need to procure an FCC license to operate. All three WLAN devices operate in the 2.4GHz Industrial, Scientific, and Medical (ISM) RF band. Additionally, the Intel PRO/Wireless 3945ABG devices operate in the lower and middle bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands. The Intel PRO/Wireless 3945ABG WLAN device is capable of three operating modes, IEEE802.11a, IEEE802.11b and IEEE802.11g. Encoding of data is modulated using Direct Sequence Spread Spectrum (DSSS) and Complementary Code Keying (CCK) when the WLAN device is operating in IEEE 802.11b mode and Orthogonal Frequency Divi-sion Multiplexing (OFDM) when operating in IEEE802.11a or IEEE802.11g mode. The WLAN device is Wi-Fi certified and operates at the maximum data transfer rate of 54 Mbps in IEEE802.11a or IEEE802.11g mode and 11 Mbps in IEEE802.11b mode.The maximum communication range indoors is approximately 80 feet (25 meters). However, that range will increase or decrease depending on factors such as number of walls, reflective material, or inter-ference from external RF sources.The WLAN device supports the following encryption methods - WEP, CKIP, TKIP, and AES encryption.WIRELESS LAN MODES USING THIS DEVICEAd Hoc Mode (See Figure A-1)"Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers.Ad Hoc mode requires that the SSID, network authenti-cation, and encryption key settings are identically configured on all computers in the Ad Hoc network. Figure A-1. Ad Hoc Mode NetworkS7020.book Page 94 Friday, May 13, 2005 3:49 PM
95WIreless LAN User’s Guide Access Point (Infrastructure) Mode (See Figure A-2)Infrastructure mode refers to a wireless network archi-tecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or can communicate with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the wired LAN in order to access computers, devices, and services such as file servers, printers, and databases.How to Handle This DeviceThe WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The Oper-ating System that your mobile computer comes with has been pre-configured to support the WLAN device. WIRELESS NETWORK CONSIDERATIONS■The WLAN devices support IEEE802.11a, IEEE802.11b and IEEE802.11g.■The WLAN devices operate in the 2.4GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.■The maximum range of the WLAN device indoors is typically 80 feet (25 meters). Please note that the max-imum range you achieve may be shorter or longer than 80 feet, depending on factors such as access point transmit power, number and density of obstructions, or external RF interference.■Microwave ovens will interfere with the operation of WLAN device as microwave ovens operate in the same 2.4GHz frequency range that IEEE802.11b/g devices operate in. Interference by microwaves does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.■Wireless devices that transmit in the 2.4GHz fre-quency range may interfere with the operation of WLAN devices in IEEE802.11b/g modes. Symptoms of interference include reduced throughput, intermittent disconnects, and large amounts of frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure the proper operation of the WLAN device.DEACTIVATING THE WLAN DEVICEDeactivation of the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). Fujitsu mobile computers employ two methods with which to deactivate the WLAN device:■Using the Wireless On/Off Switch■In Windows, using the Intel PROSet Software or Atheros Client Utility software.Figure A-2. Access Point (Infrastructure) Mode NetworkADSL modem,cable modem,or similarInternetWired LANAccess Point*Wireless LAN*An optional hub for a wiredLAN may be required dependingupon the type of access point used.S7020.book Page 95 Friday, May 13, 2005 3:49 PM
96LifeBook S7000 Series Notebook - AppendixDeactivation using the Wireless On/Off SwitchThe WLAN device can be deactivated quickly and effi-ciently by toggling the Wireless On/Off Switch to the Off position. (Figure A-3)The Wireless On/Off switch has no effect on non-Wire-less LAN models.Figure A-3. Wireless LAN On/Off Switch LocationDeactivation using the Intel PROSet SoftwareThe WLAN device can also be deactivated in Windows using the Intel PROSet Software. The procedure to accomplish this:1. Click [Start]-> [All Programs].2. Select Intel ProSet Wireless, then click on Intel ProSet Wireless from the menu that appears. The Intel ProSet Wireless utility will be displayed.3. At the bottom left corner of the window, select Wireless Off from the dropdown list.Deactivation using Atheros Client Utility software1. Right-click on Atheros Client Utility icon in the system tray. Select “Open Atheros Client Utility” from the menu.2. Choose Action and click Disable Radio.ACTIVATING THE WLAN DEVICEActivation of the WLAN device can be accomplished using the same methods as the deactivation process■Using the Wireless On/Off Switch■In Windows using the Intel PROSet Software or Atheros SoftwareWireless LANOn/Off SwitchS7020.book Page 96 Friday, May 13, 2005 3:49 PM
97WIreless LAN User’s Guide Configuration of the WLAN DeviceThe WLAN Device can be configured to establish wire-less network connectivity using one of the following tools:■Intel PROSet Software - The Intel PROSet Software allows for multiple profile setup and supports auto-matic profile switching. Support for most industry standard security solutions is contained in this soft-ware.■Atheros Client Utility - The Atheros Client Utility soft-ware allows for multiple profile setups and supports automatic profile switching. Support for most indus-try standard security solutions is contained in this software.FLOW OF OPERATIONS1. Activate the WLAN Device (See Activating the WLAN Device on page 96 for more information).2. Configure the Wireless Network parameters.■Enter the network name (SSID)■Choose the appropriate WLAN architecture (Ad Hoc or Infrastructure)■Choose Authentication method: Open, Shared, WPA-Enterprise, WPA2-Enterprise, WPA-Personal, or WPA2-Personal■If using static WEP keys, enter static WEP key and choose key index. 3. Configure network settings (See Configure Net-work Parameters on page 97 for more information)■TCP/IP settings■Workgroup or Domain settings.CONFIGURATION USING INTEL PROSET SOFTWAREThis section explains the procedure to properly configure the WLAN device using the Intel PROSet Soft-ware. Pre-defined parameters will be required for this procedure. Please consult with your network adminis-trator for these parameters:Network Name - Also known as the SSIDNetwork Key (WEP) - Required if using static WEP keys. Authentication Type - Open, Shared, WPA, or WPA-PSKProcedure1. Activate the WLAN device using either the Wireless On/Off Switch or the Intel PROSet software.2. Click the [Start] button first and then [All Pro-grams].3. Click the icon [Intel PROSet Wireless] to execute the Intel PROSet Wireless software.4. Click the [Add] button. The General Settings dialog displays. 5. Enter a profile name in the Profile Name field. 6. Enter the network SSID, in the Network Name (SSID) field. 7. Click Infrastructure or Ad Hoc for the operating mode. 8. Click [Advanced].9. The Mandatory Access Point option is only used if Infrastructure mode is selected. Use this option to connect to a specific access point. Enter the MAC address for the access point. Click OK to save the setting and return to the General Settings page. 10. Click [Next].11. If you are using Cisco CCX, click Cisco Options to enable Cisco CKIP data encryption on the Security Settings page. Check the Cisco Compatible Exten-sions Options. If you have checked the Cisco's "Mixed-Cell" box in the Advanced Setting, this option must also be checked.12. Click [OK].13. Click Next.14. Select Open, Shared, WPA-Enterprise, WPA2-Enterprise, WPA-Personal, or WPA2-Personal in the Network Authentication options. 15. Select either None, WEP, CKIP (if Enable Cisco Cli-ent eXtentions is enabled, use CKIP or WEP), or TKIP for the data encryption. 16. If WEP is selected, select either 64 or 128-bit for the Encryption Level. 17. Select the key index 1, 2, 3 or 4. 18. Enter the WEP key if required. If your network does not employ a 802.1x/EAP security mechanism, please skip to step 24.S7020.book Page 97 Friday, May 13, 2005 3:49 PM
98LifeBook S7000 Series Notebook - Appendix19. Click the Enable 802.1x checkbox to enable the 802.1x security option. Please contact your network administrator if configuration of this setting is required.20. Select the appropriate Authentication Type. Please contact your network administrator if configura-tion of this setting is required.21. After selecting your authentication type, enter the user name, domain, and password of the user you have created on the authentication server. The user name and password do not have to be the same as name and password of your current Windows user login.22. Click [OK] to save the settings.23. From the Intel ProSet Wireless page, click the new profile name shown in the Profile List. Use the up and down arrows to position the priority of the new profile in the priority list. 24. Click the Connect button to connect to the net-work. 25. Click [Close] if you want to close the Intel(R) PROSet for Wireless window.CONFIGURATION USING ATHEROS CLIENT UTILITY SOFTWAREThis section explains the procedure to properly configure the WLAN device using the Atheros Client Utility. Pre-defined parameters will be required for this procedure. Please consult with your network adminis-trator for these parameters:Network Name - Also known as the SSIDNetwork Key (WEP) - Required if using static WEP keys. Authentication Type - Open, Shared, WPA, or WPA-PSKProcedure1. Activate the WLAN device using either the Wireless On/Off Switch or the Atheros Client Utility2. Right-click on the “Atheros Client Utility” icon in the system tray, and select “Open Atheros Client Utility” from the menu.3. From the Current Status page, click the Profile Management tab. 4. If this is your first time using this utility, highlight the profile [Default] and Click the [Modify] button, otherwise Click the [New] button. The General Set-tings dialog displays. 5. From the General page, enter a profile name in the Profile Name field. 6. Enter the network SSID, in the SSID1 field. If you wish to create a profile that can connect to up to 3 different wireless networks, SSID's can be entered in the SSID2 and SSID3 fields as well.7. Click the Security tab. 8. The Security tab allows for the configuration of the Security modes listed in the table below. Please select the radio button of the desired security mode. If these settings are not known to you, please consult with your network administrator for the correct settings. 9. Click OK10. Click the Advanced tab11. The Advanced tab allows for the configuration of the options detailed in the table belowField Name DescriptionWPA Enables the use of Wi-Fi Protected Access. Choosing WPA opens the WPA EAP drop-down menu. Options include TLS and PEAP. If these settings are not known to you, please consult with your network administrator for the correct settings. WPA-PSK Enables WPA-Pre-Shared Key. Click on the Configure button to enter the WPA Passphrase. If these settings are not known to you, please consult with your network administrator for the correct settings. 802.1x Enables 802.1x security. If these settings are not known to you, please consult with your network administrator for the correct settings. Choosing this option opens the 802.1x EAP type drop-down menu. Options include TLS, PEAP, and LEAPPre-Shared Key Enables the use of pre-shared keys that are defined on both the access point and the station. This is where static WEP keys are entered. Click the Configure button to fill in the Define Pre-Shared Keys window.None No securityS7020.book Page 98 Friday, May 13, 2005 3:49 PM
99WIreless LAN User’s Guide .12. Click OK13. If the profile you just created does not activate immediately, click the Profile Management tab, highlight the desired Profile, and click Activate.14. Click [Close] if you want to close the Atheros Client Utility.CONNECTION TO THE NETWORKThis section explains connection to the network.If there is an administrator of the network, contact the network administrator for data settings.Setting the networkPerform the “Setting TCP/IP” and “Confirming the computer and work group names” operations required for network connection.Setting TCP/IP1. Click the [Start] button first and then [Control Panel].2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click [Network Connections]. A list of cur-rently installed networks will be displayed.4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis-played. The [Wireless Network Connection Proper-ties] window will be displayed.5. Click the [General] tab if it is not already selected.6. Click [Internet Protocol (TCP/IP] and then click [Properties]. The [Internet Protocol (TCP/IP) Properties] window will be displayed.7. Set the IP address as follows:■For ad hoc connection: Select [Use the following IP address:] and then enter data for [IP address] and [Subnet mask]. See page 106 for IP address setting.■For access point (infrastructure) connection: If your network uses DHCP, select [Obtain an IP address automatically] and [Obtain DNS server address automatically]. If your network uses static IP addresses, consult with your network adminis-trator for the correct IP address settings.8. Click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window.9. Click the [OK] button.10. Close the [Network Connection] window. Following this operation, confirm the names of the computer and the workgroup as follows.Confirming the computer and work group names1. Click the [Start] button, then [Control Panel].2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click the [System] icon. The [System Prop-erties] window will be displayed.4. Click the [Computer Name] tab.Field Name DescriptionPower Save ModeOptions are Maximum, Normal, or OffNetwork Type Options are AP (Infrastructure) or Ad Hoc802.11b PreambleSpecifies the preamble setting in 802.11b. The default setting is Short and Long (Access Point mode), which allows both short and long headers in the 802.11b frames. Set to Long Only to override allowing short frames.Transmit Power LevelOptions are 100%, 50%, 25%, 12.5% or Lowest transmit power (0mW)Wireless Mode Specifies 5 GHz 54 Mbps, 5 GHz 108 Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps operation in an access point network.Wireless Mode when Starting Ad Hoc NetworkSpecifies 5GHz 54 Mbps, 5 GHz 108 Mbps, 2.4 GHz 11 Mbps, or 2.4 GHz 54 Mbps to start an Ad Hoc network if no matching network name is found after scanning all available modes.To change the setting of the IP address, you need to be logged in from Windows as an administrator.To modify the computer name and/or the work group name, you need to be logged in from Windows as an administrator.S7020.book Page 99 Friday, May 13, 2005 3:49 PM
100LifeBook S7000 Series Notebook - Appendix5. Confirm the settings of [Full computer name:] and [Workgroup:].a. The setting of [Full computer name:] denotes the name for identifying the computer. Any name can be assigned for each personal computer. Enter the desired name in less than 15 ASCII character code format. Identifiability can be enhanced by entering the model number, the user name, and other factors.b. [Workgroup name] is the group name of the network. Enter the desired name in less than 15 ASCII character code format.For ad hoc connection: Assign the same network name to all personal computers existing on the network.For access point (infrastructure) connection: Assign the name of the work group to be accessed.6. Click the [OK] button. If a message is displayed that requests you to restart the personal computer, click [Yes] to restart the computer.Setting the sharing functionSet the sharing function to make file and/or printer sharing with other network-connected personal computers valid.This operation is not required unless the sharing func-tion is to be used.The folder and printer for which the sharing function has been set will be usable from any personal computer present on the network.Setting the Microsoft network-sharing service1. Click the [Start] button first and then [Control Panel]. 2. If the Control Panel is in Category view, switch to Classic view by clicking “Switch to Classic View” under Control Panel the left frame. (If you are already in Classic view, “Switch to Category View” will be displayed.) 3. Double-click [Network Connections]. A list of cur-rently installed networks will be displayed.4. Right-click [Wireless Network Connection] in the list, and then click [Properties] in the menu dis-played. The [Wireless Network Connection Proper-ties] window will be displayed.5. If [File and Printer Sharing for Microsoft Net-works] is displayed, proceed to step 6. If [File and Printer Sharing for Microsoft Networks] is not dis-played, skip to step 7.6. Make sure that the [File and Printer Sharing for Microsoft Networks] check box is checked, and then click the [OK] button. Skip to “Setting file-sharing function”.7. Click [Install]. The [Select Network Component Type] window will be displayed.8. Click [Service], then click the [Add] button. The [Select Network Service] window will be displayed.9. Click [File and Printer Sharing for Microsoft Net-works] and then click the [OK] button. Processing will return to the [Wireless Network Connection Properties] window, and [File and Printer Sharing for Microsoft Networks] will be added to the list.10. Click the [Close] button.Setting the file-sharing functionThe procedure for setting the file-sharing function follows, with the “work” folder in drive C: as an example.1. Click the [Start] button first and then [My Com-puter]. 2. Double-click [Local disk (C:)].3. Right-click the “work” folder (or whichever folder you want to share), and then click [Sharing and Security...] in the menu displayed. The [Folder Name Properties] window will be displayed.4. Click [Sharing] if it isn’t already selected.5. Click the link stating “If you understand the secu-rity risks, but want to share files without running the wizard, click here”.6. Click “Just enable file sharing” and click [OK].To change the name, click [Change] and then proceed in accordance with the instruction messages displayed on the screen.To share a file and/or the connected printer, you need to be logged in as an administrator.Setting the file-sharing function for the file which has been used to execute Network Setup Wizard is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the file-sharing function easily without using Network Setup Wizard are given below.S7020.book Page 100 Friday, May 13, 2005 3:49 PM
101WIreless LAN User’s Guide 7. Check the [Share this folder on the network] check box.8. Click the [OK] button. The folder will be set as a sharable folder, and the display of the icon for the “work.” folder will change.Setting the printer-sharing function1. Click the [Start] button first and then [Printers and FAX]. A list of connected printers will be displayed.2. Right-click the printer for which the sharing func-tion is to be set, and then click [Sharing] in the menu displayed. The property window correspond-ing to the selected printer will be displayed.3. Click the [Sharing] tab.4. Click [Share this printer].5. Enter the sharing printer name in [Share name].6. Click the [OK] button. Confirming connectionAfter you have finished the network setup operations, access the folder whose sharing has been set for other personal computers. Also, confirm the status of the radio waves in case of trouble such as a network connection failure.Connecting your personal computer to another personal computer1. Click [Start] first and then [My Computer]. The [My Computer] window will be displayed in the left frame.2. Click [My Network Places] in the “Other Places” list. The window [My Network Places] will be dis-played.3. Click [View workgroup computers] under Network Tasks in the left frame.4. Double-click the personal computer to which your personal computer is to be connected. The folder that was specified in “Setting the file-sharing func-tion” on page 100 will be displayed.5. Double-click the folder to be accessed.Confirming the status of the radio1. Right-click the Intel PRO Wireless icon in the lower right corner of the screen.2. Click [Open Intel PROSet for Wireless]. The Intel PROSet for Wireless window opens.3. Contained within the General tab and the Details section (accessed by pressing the [Details] button), you will find the current operating status of the radio. (When the radio is turned off or the com-puter is not yet connected, some of the conditions will not be displayed.)■Profile NameThe current configuration profile is displayed.■Network Name (SSID)Displays the Network Name (SSID) currently used by the radio.■IP AddressThe IP address of the current profile.■Signal QualityDisplays a message stating the current quality of the signal.■Signal StrengthDisplays a graphic representation of the current signal strength.Additionally, in the lower section of the display, you will see a variety of different measurements related to the WLAN. For additional information about the items, click on the “Help?” button:■Adapter MAC Address■Band■Supported Data Rates■Radio Frequency■Channel Number■Network Authentication■Data Encryption■802.1x Authentication TypeTo specify the corresponding folder as a read-only folder, select the [Read only] checkbox under the General tab.Setting the printer-sharing function when Network Setup Wizard has been executed is suggested on the screen. For the wireless LAN, however, since security is guaranteed by entry of the network name (SSID) and the network key, the steps to be taken to set the printer-sharing function without using Network Setup Wizard are laid down below.In the case of access point (infrastructure) connection, enter the necessary data for the access point before confirming connection. Refer to the manual of the access point for the access point setup procedure.S7020.book Page 101 Friday, May 13, 2005 3:49 PM
102LifeBook S7000 Series Notebook - Appendix■802.1x Authentication Protocol■CCX Version■CCX TPC■CCX Power Levels■Access Point MAC Address■Mandatory Access PointS7020.book Page 102 Friday, May 13, 2005 3:49 PM
103WIreless LAN User’s Guide Troubleshooting the WLANTROUBLESHOOTINGCauses and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. Problem Possible Cause Possible SolutionUnavailable network connectionIncorrect network name (SSID) or network keyAd hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.Access Point (Infrastructure) connection: set the network name (SSID) and network key to the same values as those of the access point. Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary. Weak received signal strength and/or link qualityAd hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight.Access Point (Infrastructure) connection: Retry connection after short-ening the distance to the access point or removing any obstacles for better sight.To check the wave condition, refer to the following page:· “Confirming the status of the radio waves” on page 101.The WLAN device has been deactivated or disabledCheck if the wireless switch is turned ON. Also verify “Disable Radio” is not checked in “Network setting” window. Refer to “Activating the Wireless LAN” on page 96.The computer to be connected is turned offCheck if the computer to be connected is turned ON.RF interference from Access Points or other wireless networksThe use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device.Wireless network authentication has failedRe-check your Network Authentication, Encryption, and Security settings. Incorrectly configured security settings such as an incorrectly typed WEP key, a misconfigured LEAP username, or an incorrectly chosen authentication method will cause the LAN device to associate but not authenticate to the wireless network.Incorrectly configured network settingsRecheck the configuration of your network settings.For the method of checking, refer to the following page:·“Connection to the Network” on page 99.Incorrect IP address configurationThis only applies to networks using static IP addresses. Please contact your network administrator for the correct settings.S7020.book Page 103 Friday, May 13, 2005 3:49 PM
104LifeBook S7000 Series Notebook - AppendixWireless LAN GlossaryGLOSSARYAccess pointWireless network device used to bridge wireless and wired network traffic. Ad Hoc ModeAd Hoc Mode refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion. For details, refer to “Ad hoc connection” on page 94.CCX (Cisco Compatible Extensions)Implementation that provides improved wireless data security, ensuring certified compatibility with Cisco wireless access points.ChannelRange of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.DHCP (Dynamic Host Configuration Protocol)A protocol that provides a means to dynamically allocate IP addresses to computers on a local area network.DNS (Domain Name System)A data query service that provides a mechanism with which to translate host names into Internet addresses.EAPExtensible Authentication ProtocolA protocol implementation that provides a framework to allow easier user authentication.IEEE802.11aWireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands. IEEE802.11bWireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz ISM band. IP addressThe logical 32-bit host address defined by the Internet Protocol that uniquely identifies a computer on a network. The IP address is usually expressed in dotted decimal notation.LAN (Local Area Network)A LAN or Local Area Network is a computer network (or data communications network) which is confined to a limited geographical area.MAC address (Media Access Control Address)A MAC address (also called an Ethernet address or IEEE MAC address) is the 48-bit address (typically written as twelve hexadecimal digits, 0 through 9 and A through F, or as six hexadecimal numbers separated by periods or colons, e.g., 0080002012ef, 0:80:0:2:20:ef) which uniquely identifies a computer that has an Ethernet interface.MTU (Maximum Transmission Unit)The maximum size of data which can be transmitted at one time in networks including the Internet. In an envi-ronment whose maximum size of data is too large to correctly receive data, normal communications can be restored by setting the size of MTU to a smaller value.Network keyData that is used for encrypting data in data communi-cation. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.Network name (SSID: Security Set Identifier)When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.Open system authenticationNull authentication method specified in the 802.11 stan-dard that performs no authentication checks on a wire-less client before allowing it to associate.S7020.book Page 104 Friday, May 13, 2005 3:49 PM
105WIreless LAN User’s Guide PEAP (Protected Extensible Authentication Protocol)An improvement over EAP, making authentication much easier to achieve.PPPoE (Point to Point Protocol over Ethernet)A method of allowing the authentication protocol adopted in telephone line connection (PPP) to be used over an Ethernet.ProtocolA procedure or rule of delivering data among computers. Ordered data communication is allowed by making all conditions required for communication including the method of data transmission/reception and actions upon communication errors into proce-dures.Shared key authentication802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP. If the client has the wrong key or no key, authentication will fail and the client will not be allowed to associate with the AP. Shared key authentica-tion is not considered secure, because a hacker who detects both the clear-text challenge and the same chal-lenge encrypted with a WEP key can decipher the WEP key.SSID (Service Set Identifier)Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID. Because the SSID is broadcast in plain text, it does not supply any security to the network. Subnet maskTCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.TCP/IP (Transmission Control Protocol/Internet Protocol)A standard protocol of the Internet. TKIP (Temporal Key Integrity Protocol)Security feature that is a WEP enhancement to defend against known wireless data security issues.WEP (Wired Equivalent Privacy)Standard wireless security provided by the Wi-Fi stan-dard, used for protecting wireless data.Wi-Fi Wi-Fi, or Wireless Fidelity, is a set of standards for wire-less local area networks (WLAN) based on the IEEE 802.11 specifications. Certified products can use the official Wi-Fi logo, which indicates that the product is interoperable with any other product also showing that logo.WPA (Wi-Fi Protected Access)Strong replacement for WEP, providing improved data encryption and user authentication.S7020.book Page 105 Friday, May 13, 2005 3:49 PM
106LifeBook S7000 Series Notebook - AppendixIP address informationABOUT IP ADDRESSESIf IP address is unknown, set IP address as follows:If you have an access point (DHCP server) on the network, set the IP address as follows:[Obtain an IP address automatically]If the IP address is already assigned to the computer in the network, ask the network administrator to check the IP address to be set for the computer.If no access point is found in the network:An IP address is expressed with four values in the range between 1 and 255.Set the each computer as follows: The value in paren-theses is a subnet mask.<Example>Computer A: 192.168.100.2 (255.255.255.0)Computer B: 192.168.100.3 (255.255.255.0)Computer C: 192.168.100.4 (255.255.255.0)::Computer X: 192.168.100.254 (255.255.255.0)IP addressing is much more complicated than can be briefly explained in this document. You are advised to consult with your network administrator for additional information.A DHCP server is a server that automatically assigns IP addresses to computers or other devices in the network. There is no DHCP server for the AdHoc network.S7020.book Page 106 Friday, May 13, 2005 3:49 PM
107WIreless LAN User’s Guide Specifications* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/104 bits after subtracting the fixed length of 24 bits.*** Depending on practical environments, the allowable number of computers to be connected may be decreased.Item SpecificationType of network The Atheros AR5002X (WLL4070) and the Intel PRO/Wireless 2915ABG (WM3B2915ABG) Network Connections WLAN devices conform to IEEE 802.11a and 802.11b/g (Wi-Fi based)*.Transfer rate (Automatic switching)IEEE 802.11a/g: 54 Mbps maximum data rate IEEE 802.11b: 11 Mbps maximum data rateActive frequency 802.11b/g: 2400~2473 MHz 802.11a: 5050 ~ 5850 MHzNumber of channels 802.11a: 8 independent channels802.11b/g: 11 channels, 3 non-overlapping channels Security Encryption Types - WEP, TKIP, AES**WPA 1.0 compliant Encryption key lengths supported: 64 bits, 128 bits, and 152 bits (Atheros module using AES encryption only)802.1x/EAPMaximum recommended number of computers to be connected over wireless LAN (during ad hoc connection)10 units or less ***S7020.book Page 107 Friday, May 13, 2005 3:49 PM
108WIreless LAN User’s Guide Using the Bluetooth DeviceThe Integrated Bluetooth module (EYTF3CSFT) is an optional device available for Fujitsu mobile computers. WHAT IS BLUETOOTHBluetooth technology is designed as a short-range wire-less link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other. WHERE TO FIND INFORMATIONABOUT BLUETOOTHThe Bluetooth module contains a robust Help user’s guide to assist you in learning about operation of the Bluetooth device.To access the Help file, click [Start] -> All Programs, and click on Toshiba. Select Bluetooth, then select User’s Guide.For additional information about Bluetooth Technology, visit the Bluetooth Web site at: www.bluetooth.com.FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The Bluetooth antenna is located to the l eft of [Tab] key,above the air vent and is exempt from minimum criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.Canadian NoticeTo prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.WarrantyUsers are not authorized to modify this product. Any modifications invalidate the warranty.This equipment may not be modified, altered, or changed in any way without signed written permission from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and Industry Canada and the warranty.The Wireless LAN/Bluetooth On/Off Switch will power off both the optional wireless LAN and Bluetooth devices at the same time. To enable or disable either one of the devices individually, perform the following steps:1. Slide the Wireless LAN/Bluetooth on/off switch to On position.2. In the Control Panel, double-click the Fujitsu Radio Control icon.3. In the window that appears, click the button associated with Bluetooth and/or Wireless LAN Status to enable or dis-able the individual devices.4. Click [OK].E8020.book Page 107 Thursday, March 10, 2005 1:55 PMdistance
109Appendix BUsing the Fingerprint Sensor* * Optional DeviceS7020.book Page 109 Friday, May 13, 2005 3:49 PM
110LifeBook S7000 Notebook – AppendixS7020.book Page 110 Friday, May 13, 2005 3:49 PM
111Using the Fingerprint SensorFingerprint Sensor DeviceINTRODUCING THE OPTIONAL FINGERPRINT SENSOR DEVICEYour system may have an optional fingerprint sensor device in the location at which other models have a scroll button. (Figure B-1) Figure B-1 Fingerprint sensorWith a fingerprint sensor, you can avoid having to enter a username and password every time you want to:■Log onto Windows■Recover from suspend mode■Cancel a password-protected screen saver■Log into homepages that require a username and pass-wordAfter you have “enrolled” - or registered - your finger-print, you can simply swipe your fingertip over the sensor for the system recognize you. The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and on-line passwords. OmniPass requires users to authenticate themselves using the fingerprint sensor before granting access to the Windows desktop. This device results in a secure authentication system for restricting access to your computer, applications, web sites, and other password-protected resources.OmniPass presents a convenient graphical user interface, through which you can securely manage passwords, users, and multiple identities for each user.GETTING STARTEDThis section guides you through the preparation of your system for the OmniPass fingerprint recognition application. You will be led through the OmniPass installation process. You will also be led through the procedure of enrolling your first user into OmniPass. INSTALLING OMNIPASSIf OmniPass has already been installed on your system, skip this section and go directly to “User Enrollment” on page 112. You can determine whether OmniPass has already been installed by checking to see if the following are present:■The presence of the gold key-shaped OmniPass icon in the system tray at the bottom right of the screen.■The presence of the Softex program group in the Programs group of the Start menuSystem RequirementsThe OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows:■Windows XP Home Edition or Windows XP Profes-sional operating system■At least 35 MB available hard disk spaceInstalling the OmniPass ApplicationIf OmniPass is already installed on your system, go to “User Enrollment” on page 112. Otherwise continue with this section on software installation.To install OmniPass on your system you must:1. Insert the installation media for the OmniPass appli-cation into the appropriate drive. If you are installing from CD-ROM or DVD-ROM, you must find and launch the OmniPass installation program (setup.exe) from the media.2. Follow the directions provided in the OmniPass installation program. Specify a location to which you would like OmniPass installed. It is recom-mended that you NOT install OmniPass in the root directory (e.g. C:\). 3. Once OmniPass has completed installation you will be prompted to restart you system. Once your system has rebooted you will be able to use OmniPass. If you choose not to restart immediately after installation, OmniPass will not be available for use until the next reboot.Although the system may have a fingerprint sensor in place of a scroll button, the fingerprint sensor can be used for scrolling. Simply move your fingerprint over the sensor the same as you would use a scroll button. For installation, OmniPass requires that the user installing OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass installation.S7020.book Page 111 Friday, May 13, 2005 3:49 PM
112LifeBook S7000 Notebook – AppendixThe installation program automatically places an icon (Softex OmniPass) in the Windows Control Panel as well as a golden key shaped icon in the taskbar. Verifying Information about OmniPassAfter you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system.To check the version information of OmniPass:1. From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen),or,Click the Start button, select Settings, and click Control Panel (if you are using Windows XP you will see the Control Panel directly in the Start menu; click it, then click Switch to Classic View). Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear. If it does not appear, then the program is not properly installed,or,Click the Start button, select Programs, and from the submenu select the Softex program group, from that submenu click OmniPass Control Center.2. Select the About tab at the top of the OmniPass Control Panel. The About tab window appears with version information about OmniPass.Uninstalling OmniPassTo remove the OmniPass application from your system:1. Click Start on the Windows taskbar. Select Settings, and then Control Panel.2. Double-click Add/Remove Programs.3. Select OmniPass, and then click Change/Remove.4. Follow the directions to uninstall the OmniPass application.5. Once OmniPass has finished uninstalling, reboot your system when prompted.USER ENROLLMENTBefore you can use any OmniPass features you must first enroll a user into OmniPass.Master Password ConceptComputer resources are often protected with passwords. Whether you are logging into your computer, accessing your email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access. This can result in dozens of sets of creden-tials that you have to remember.During OmniPass user enrollment a "master password” is created for the enrolled user. This master password “replaces” all other passwords for sites you register with OmniPass. Example: A user, John, installs OmniPass on his system (his home computer) and enrolls an OmniPass user with username “John_01” and password “freq14”. He then goes to his webmail site to log onto his account. He inputs his webmail credentials as usual (username “John_02” and password “lifebook”), but instead of clicking [Submit], he directs OmniPass to Remember Password. Now whenever he returns to that site, OmniPass will prompt him to supply access credentials. John enters his OmniPass user credentials (“John_01” and “freq14”) in the OmniPass authentication prompt, and he is allowed into his webmail account. He can do this with as many web sites or password protected resources he likes, and he will gain access to all those sites with his OmniPass user credentials (“John_01” and “freq14”). This is assuming he is accessing those sites with the system onto which he enrolled his OmniPass user. OmniPass does not actually change the credentials of the password protected resource. If John were to go to an Internet cafe to access his webmail, he would need to enter his original webmail credentials (“John_02” and “lifebook”) to gain access. If he attempts his OmniPass user credentials on a system other than where he enrolled that OmniPass user, he will not gain access.Basic EnrollmentThe Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified other-wise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard.1. Click Enroll to proceed to username and password verification. By default, the OmniPass Enrollment Wizard enters the credentials of the currently logged in Windows user.2. Enter the password you use to log in to Windows. This will become the “master password” for this OmniPass user. In most cases, the Domain: value For uninstallation, OmniPass requires that the user uninstalling OmniPass have administrative privileges to the system. If your current user does not have administrative privileges, log out and then log in with an administrator user before proceeding with OmniPass uninstallation.The enrollment procedure assumes you have no hardware authentication devices or alternate storage locations that you wish to integrate with OmniPass. If you desire such functionality, consult the appropriate sections of this document.S7020.book Page 112 Friday, May 13, 2005 3:49 PM
113Using the Fingerprint Sensorwill be your Windows computer name. In a corpo-rate environment, or when accessing corporate resources, the Domain: may not be your Windows computer name. Click [Next] to continue.3. In this step OmniPass captures your fingerprint. Refer to “Enrolling a Fingerprint” on page 113 for additional information.4. Next, choose how OmniPass notifies you of various events. We recommend you keep Taskbar Tips on Beginner mode taskbar tips and Audio Tips on at least Prompt with system beeps only until you get accustomed to how OmniPass operates. Click [Next] to proceed with user enrollment. You will then see a Congratulations screen indicating your completion of user enrollment.5. Click [Done] to exit the OmniPass Enrollment Wizard. You will be asked if you’d like to log in to OmniPass with your newly enrolled user; click [Yes].Enrolling a FingerprintEnrolling a fingerprint will increase the security of your system and streamline the authentication procedure. You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the User Settings area. Click Enroll Authentication Device and authenticate at the authentication prompt to start device enrollment.1. During initial user enrollment, you will be prompted to select the finger you wish to enroll. Fingers that have already been enrolled will be marked by a green check. The finger you select to enroll at this time will be marked by a red arrow. OmniPass will allow you re-enroll a finger. If you choose a finger that has already been enrolled and continue enrollment, OmniPass will enroll the fingerprint, overwriting the old fingerprint. Select a finger to enroll and click [Next].2. It is now time for OmniPass to capture your selected fingerprint. It may take a several capture attempts before OmniPass acquires your fingerprint. Should OmniPass fail to acquire your fingerprint, or if the capture screen times out, click [Back] to restart the fingerprint enrollment process. Your system has a “swipe” fingerprint sensor. A swipe sensor is small and resembles a skinny elon-gated rectangle. To capture a fingerprint, gently swipe or pull your fingertip over the sensor (starting at the second knuckle) towards yourself. Swiping too fast or too slow will result in a failed capture. The Choose Finger screen has a [Practice] button; click it to practice capturing your fingerprint. When you are comfortable with how your fingerprint is captured, proceed to enroll a finger.3. Once OmniPass has successfully acquired the finger-print, the Ver i fy Fin ger pri nt screen will automati-cally appear. To verify your enrolled fingerprint, place your fingertip on the sensor and hold it there as if you were having a fingerprint captured. Successful fingerprint verification will show a green fingerprint in the capture window and the text Ver i -fication Successful under the capture window.USING OMNIPASSYou are now ready to begin using OmniPass. Used regu-larly, OmniPass will streamline your authentications.Password ReplacementYou will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials. OmniPass can detect these prompts and you can teach OmniPass your login credentials. The next time you go to that website, you can authenticate with your fingerprint to gain access.OmniPass Authentication ToolbarAfter installing OmniPass and restarting, you will notice a dialog you have not seen before at Windows Logon. This is the OmniPass Authentication Toolbar, and it is displayed whenever the OmniPass authentication system is invoked. The OmniPass authentication system may be invoked frequently: during Windows Logon, during OmniPass Logon, when unlocking your workstation, when resuming from standby or hibernate, when unlocking a password-enabled screensaver, during pass-word replacement for remembered site or application logins, and more. When you see this toolbar, OmniPass is prompting you to authenticate.The Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not. When you click the icon for an unse-lected authentication method, the authentication prompt associated with that method is displayed.When prompted to authenticate, you must supply the appropriate credentials: an enrolled finger for the finger-print capture window or your master password for the master password prompt (the key icon).Remembering a PasswordOmniPass can remember any application, GUI, or pass-word protected resource that has a password prompt.Using the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint.S7020.book Page 113 Friday, May 13, 2005 3:49 PM
114LifeBook S7000 Notebook – AppendixGo to a site that requires a login (username and pass-word), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login). Right-click the OmniPass system tray icon and select Remember Password from the submenu. The Windows arrow cursor will change to a golden key OmniPass cursor. Click this OmniPass cursor in the login prompt area, but do not click the [Login] or [Submit] button.Associating a Friendly NameAfter clicking the OmniPass key cursor near the login prompt, OmniPass will prompt you to enter a “friendly name” for this site. You should enter something that reminds you of the website, the company, or the service you are logging into. In its secure database, OmniPass associates this friendly name with this website.Additional Settings for Remembering a SiteWhen OmniPass prompts you to enter a “friendly name” you also have the opportunity to set how OmniPass authenticates you to this site. There are three effective settings for how OmniPass handles a remembered site.The default setting is Automatically click the “OK” or “Submit” button for this password protected site once the user is authenticated. With this setting, each time you navigate to this site OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass, you will automatically be logged into the site. Less secure is the option to Automatically enter this password protected site when it is activated. Do not prompt for authentication. Check the upper box to get this setting, and each time you navigate to this site OmniPass will log you into the site without prompting you to authenticate.If you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master pass-word or fingerprint authentication device. Once you have authenticated with OmniPass your credentials will be filled in to the site login prompt, but you will have to click the website [OK], [Submit], or [Login] button to gain access to the site. Click Finish to complete the remember password proce-dure. The site location, the credentials to access the site, and the OmniPass authentication settings for the site are now stored in the OmniPass secure database. The OmniPass authentication settings (Settings for this Pass-word Site) can always be changed in Vault Management.Logging in to a Remembered SiteWhether or not OmniPass prompts you to authenticate when you return to a remembered site is determined by Settings for this Password Site and can be changed in Vault Management. The following cases are applicable to using OmniPass to login to: Windows, remembered web sites, and all other password protected resources.With Master PasswordOnce you return to a site you have remembered with OmniPass, you may be presented with a master pass-word prompt. Enter your master password and you will be allowed into the site.Logging into Windows with a Fingerprint DeviceWhen logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.In Windows XP, your login options must be set either for classic login, or for fast user switching and logon screen to be enabled to use your fingerprint to log on to Windows. To change this go to Control Panel, select User Accounts and then click Change the way users log on or off. If your Windows screensaver is password protected, the fingerprint capture window will now appear next to screensaver password dialog during resume. You can authenticate to your screensaver pass-word prompt with your enrolled finger.Password ManagementOmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Vau lt Ma nage-ment; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Pass-words under Vault Settings. You will see the Manage Passwords interface, with a list of friendly names.This setting is more convenient in that whenever you go to a site remembered with this setting, you will bypass any authentication procedure and gain instant access to the site. But should you leave your system unattended with your OmniPass user logged in, anyone using your system can browse to your password protected sites and gain automatic access.If a machine is locked and OmniPass detects a different user logging back in with a fingerprint, the first user will be logged out and the second user logged in.S7020.book Page 114 Friday, May 13, 2005 3:49 PM
115Using the Fingerprint SensorYou can view the credentials stored for any remembered website by highlighting the desired resource under Pass-word Protected Dialog and clicking Unmask Values. Should a password be reset, or an account expire, you can remove stored credentials from OmniPass. Highlight the desired resource under Password Protected Dialog and click Delete Page. You will be prompted to confirm the password deletion.The two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site.OmniPass will overwrite an old set of credentials for a website if you attempt to use Remember Password on an already remembered site. The exception to the above rule is the resetting of your Windows password. If your password is reset in Windows, then the next time you login to Windows, OmniPass will detect the password change and prompt you to “Update” or “Reconfirm” your password with OmniPass. Enter your new Windows password in the prompt(s) and click OK and your OmniPass "master password" will still be your Windows password.OmniPass User IdentitiesIdentities allow OmniPass users to have multiple accounts to the same site (e.g., bob@biblomail.com and boballen@biblomail.com). If OmniPass did not provide you identities, you would be limited to remembering one account per site.To create and manage identities, double-click the OmniPass key in the system tray. Click Vau lt Manage-ment; OmniPass will prompt you to authenticate. Once you gain access to Vault Management, click Manage Identities under Vault Settings. You can only manage the identities of the currently logged in OmniPass userTo add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply]. You can now switch to the new identity and start remembering passwords.To delete an identity, highlight the identity you want to delete and click [Delete Identity], then click [Apply].To set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automati-cally be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password".Choosing User Identity during LoginTo choose your identity during login, type your user-name in the User Name: field. Press [Tab] and see that the Domain: field self-populates. Click the Password: field to bring the cursor to it, and you will see the pull-down menu in the Identity: field. Select the identity you wish to login as and then click OK to login.Switch User IdentityTo switch identities at any time, right-click the OmniPass system tray icon and click Switch User Iden-tity from the submenu. The Switch Identity dialog will appear. Select the desired identity and then click OK.Identities and Password ManagementOn the Manage Passwords interface of the Va u l t Management tab of the OmniPass Control Center, there is a pull-down selection box labeled, Identity. This field lets you choose which identity you are managing pass-words for. When you select an identity here, only those password protected dialogs that are associated with that identity are shown. You can perform all the functions explained in “Password Management” on page 114.CONFIGURING OMNIPASSThis section gives an overview of both the Export/Import function and the OmniPass Control Center. Exporting and Importing UsersUsing the OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and any enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported. When you delete an identity, all of its associated remembered sites and password protected dialogs are lost.■You should periodically export your user profile and store it in a safe place. If anything happens to your system, you can import your OmniPass profile to a new system and have all your remem-bered settings and fingerprints instantly.■You don't forget the Windows login credentials when exporting. When you examine the importation, you are prompted for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain.S7020.book Page 115 Friday, May 13, 2005 3:49 PM
116LifeBook S7000 Notebook – AppendixExporting an OmniPass User ProfileTo export a user, open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Exports an OmniPass user profile. OmniPass will prompt you to authenticate. Upon successfully authenti-cation, you must name the OmniPass user profile and decide where to save it. An .opi file is generated, and you should store a copy of it in a safe place.This .opi file contains all your user specific OmniPass data, and it is both encrypted and password protected. This user profile does NOT contain any of your encrypted data files.Importing an OmniPass User ProfileTo import an OmniPass user open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Imports a new user into OmniPass and then select OmniPass Import/Export File (*.opi) and click Next. OmniPass will then prompt you to browse for the file you had previously exported (.opi file). When you select the .opi file for importation, OmniPass will prompt you for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name.OmniPass will notify you if the user was successfully imported.Things to Know Regarding Import/Export■Assume you export a local Windows User profile from OmniPass. You want to import that profile to another machine that has OmniPass. Before you can import the profile, a Windows user with the same login cre-dentials must be created on the machine importing the profile.Example: I have a Windows user with the username “Tom” and the password “Sunshine” on my system. I have enrolled Tom into OmniPass and remembered passwords. I want to take all my passwords to new sys-tem. I export Tom’s OmniPass user profile. I go to my new system and using the Control Panel I create a user with the username "Tom" and the password "Sun-shine". I can now successfully import the OmniPass user data to the new system.■If you export an OmniPass-only user, you can import that user to any computer running OmniPass, pro-vided that a user with that name is not already enrolled in OmniPass. ■If you attempt to import a user profile who has the same name as a user already enrolled in OmniPass, the OmniPass import function will fail.OMNIPASS CONTROL CENTERThis section will serve to explain functions within the OmniPass Control Center that weren’t explained earlier. You can access the OmniPass Control Center any of three ways:■Double-click the golden OmniPass key shaped icon in the Windows taskbar (typically in the lower-right cor-ner of the desktop)■Click the Start button; select the Programs group; select the Softex program group; and click the OmniPass Control Center selection.■Open the Windows Control Panel (accessible via Start button --> Settings --> Control Panel) and double-click the Softex OmniPass icon.User ManagementThe User Management tab has two major interfaces: Add/Remove User and Import/Export User. Import/Export User functionality is documented in “Exporting and Importing Users” on page 115. Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard. The Enrollment Wizard is documented in “User Enrollment” on page 112. If you click Removes a user from OmniPass, OmniPass will prompt you to authenticate. Authenticate with the credentials (or enrolled fingerprint) of the user you wish to remove. OmniPass will prompt you to confirm user removal. Click OK to complete user removal.User SettingsThe User Settings tab has four interfaces: Audio Settings, Tas kb ar Tip s, and Enrollment. User settings allow users to customize OmniPass to suit their individual prefer-ences. Under User Settings (Audio Settings and Ta s kb ar Tips) you can set how OmniPass notifies the user of OmniPass events (e.g., successful login, access denied, You cannot import a user into OmniPass if there already is a user with the same name enrolled in OmniPass. Removing a user will automatically destroy all OmniPass data associated with that user. All identities and credentials associated with the user will be lost.If you are sure about removing the user, we recommend you export the user profile.S7020.book Page 116 Friday, May 13, 2005 3:49 PM
117Using the Fingerprint Sensoretc.). The details of each setting under the Audio Settings and Taskbar Tips interfaces are self-explana-tory.The Enrollment interface allows you to enroll finger-prints. For the procedure to enroll and authentication device refer to Chapter 2.3. To enroll additional finger-prints, click Enroll Authentication Device, and authen-ticate with OmniPass. Select the fingerprint recognition device in the Select Authentication Device screen (it should already be marked by a green check if you have a finger enrolled) and click Next.System SettingsThe OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon.The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass. This setting is appropriate for an office setting or any setting where users must enter a username and password to log into a computer. This is the default setting.With the second option, Manually log on to OmniPass at startup, OmniPass will prompt you to login once you have logged on to Windows.With the third option, Do not log on to OmniPass at startup, OmniPass will not prompt for a user to be logged on.You can manually log on to OmniPass by right-clicking the OmniPass taskbar icon and clicking Log in User from the right-click menu.TROUBLESHOOTINGYou cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and passwordCannot add Windows users to OmniPassIf you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local secu-rity settings. You can do this by going to Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Network Access: Sharing and Security Model for Local Accounts. The correct setting should be Classic - Local Users Authen-ticate as Themselves.Cannot add a User with a Blank Password to OmniPassIf you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the proce-dure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure.Click Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Accounts: Limit local account use of blank pass-words to console login only. This setting should be set to Disabled.Dialog appears after OmniPass authentication during Windows LogonAfter installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box.This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). This could happen for any of the following reasons:■Your Windows password has changed■Your Windows account has been disabledIf you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password.Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.S7020.book Page 117 Friday, May 13, 2005 3:49 PM
118LifeBook S7000 Notebook – AppendixS7020.book Page 118 Friday, May 13, 2005 3:49 PM
119IndexIndexAAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1ACadapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Anti-theft lock slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Application Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . 27Automatically Downloading Driver Updates . . . . . . 67BBattery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72charging indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 11cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . . 32dead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11lithium ion battery . . . . . . . . . . . . . . . . . . . . . . . . . . 40low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60, 61recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40BIOSguide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56CCapsLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56, 57Centrino . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 41Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . 10, 77Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . 6Conventions Used in the Guide . . . . . . . . . . . . . . . . . . 1Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13DDC Power Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 27Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50, 78Diskcare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 28adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Dolby Headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Drivers and Application Restore CD . . . . . . . . . . . . . 66DVD driveaccess indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12tray release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65DVD/CD-RW/CD-ROM drive . . . . . . . . . . . . . . . . . . 37access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56, 57DVD-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37EEmergency tray release . . . . . . . . . . . . . . . . . . . . . . . . . 8Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64ExpressCards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43External Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . 42problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57External Monitor Port . . . . . . . . . . . . . . . . . . . . . . . 7, 52S7020.book Page 119 Friday, May 13, 2005 3:49 PM
120LifeBook S7000 NotebookFFDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Fingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . 111enrolling a fingerprint . . . . . . . . . . . . . . . . . . . . . 113getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . 111logging into a remembered site . . . . . . . . . . . . . . 114OmniPass authentication toolbar . . . . . . . . . . . . 113password replacement . . . . . . . . . . . . . . . . . . . . . 113remembering a password . . . . . . . . . . . . . . . . . . . 113uninstalling OmniPass . . . . . . . . . . . . . . . . . . . . . 112user enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . 112using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . 113Flexible Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 18cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18eject lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Floppy Diskejecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42preparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42write protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . 1Fujitsu Driver Update utility . . . . . . . . . . . . . . . . . . . 67Fujitsu LifeBookstoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Function KeyF10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14F3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14F4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14F6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14F7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14F8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 17F9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 17FN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14HHard Disk Driveaccess indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 52Hibernation Feature . . . . . . . . . . . . . . . . . . . . . . . . . . 33disable/enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33IInfrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 51Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44Internal LAN Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51KKeyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6, 13cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .13problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13LLAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9LifeBook Security Application Panel . . . . . . . . . . . . . .6buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22configuring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23deactivating and activating . . . . . . . . . . . . . . . . . . .23launching applications . . . . . . . . . . . . . . . . . . . . . . .22operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21MMedia Playercare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37, 38using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39Memorycapacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46compartment . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 45installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45, 46upgrade module . . . . . . . . . . . . . . . . . . . . . . . . . . . .45Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58Modem Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50Modem Result Codes . . . . . . . . . . . . . . . . . . . . . . . . . .65Modular Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18S7020.book Page 120 Friday, May 13, 2005 3:49 PM
121IndexMouse problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Multi-Format DVD Writer . . . . . . . . . . . . . . . . . . . . . 37NNumeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13NumLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12OOptical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37PParallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58, 59PC Cardaccess indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73eject button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7installing/removing . . . . . . . . . . . . . . . . . . . . . . . . . 43problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7PC Cardsremoving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Pointing DeviceSee Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48back panel components . . . . . . . . . . . . . . . . . . . . . .47connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10detaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57PowerAC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Auto/Airline adapter . . . . . . . . . . . . . . . . . . . . . . . . 27failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59, 60indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Power Management . . . . . . . . . . . . . . . . . . . . . . . .32, 33Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . . 29, 64Power/Suspend/Resume Button . . . . . . . . . . . . . . . 6, 32Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . . 79Adobe Acrobat Reader . . . . . . . . . . . . . . . . . . . . . . . 79Fujitsu HotKey . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79LifeBook Application Panel . . . . . . . . . . . . . . . . . .80manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Norton AntiVirus 2004 . . . . . . . . . . . . . . . . . . . . . . 80Quicken New User Edition . . . . . . . . . . . . . . . . . . .80PS/2 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51RRegistration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 31Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50SScrLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 45Security Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Security Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58, 59Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . 79Environmental Requirements . . . . . . . . . . . . . . . . 79Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . 6, 11Stereo Line-in Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Stereo Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32TTouchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 15buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16pointing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6scroll button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55UUnpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59USB 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 51problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58USB 2.0 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9VVolume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17S7020.book Page 121 Friday, May 13, 2005 3:49 PM
122LifeBook S7000 NotebookWWarranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1WindowsWindows XP Home . . . . . . . . . . . . . . . . . . . . . . . . . 1Windows XP Professional . . . . . . . . . . . . . . . . . . . . 1Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Start keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Wireless LANaccess point (infrastructure) mode . . . . . . . . . . . . 95activating the WLAN device . . . . . . . . . . . . . . . . . 96ad hoc mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94before using the wireless LAN . . . . . . . . . . . . . . . . 94configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97deactivating the WLAN device . . . . . . . . . . . . . . . 95devices covered by this document . . . . . . . . . . . . . 94IP address information . . . . . . . . . . . . . . . . . . . . . 106modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 103using Atheros Client Utility software . . . . . . . . . . 98using Intel PROSet software . . . . . . . . . . . . . . . . . 97wireless LAN glossary . . . . . . . . . . . . . . . . . . . . . . 104wireless network considerations . . . . . . . . . . . . . . 95S7020.book Page 122 Friday, May 13, 2005 3:49 PM
S7020.book Page 123 Friday, May 13, 2005 3:49 PM
S7020.book Page 124 Friday, May 13, 2005 3:49 PM
S7020.book Page 125 Friday, May 13, 2005 3:49 PM
S7020.book Page 126 Friday, May 13, 2005 3:49 PM
S7020.book Page 127 Friday, May 13, 2005 3:49 PM
S7020.book Page 128 Friday, May 13, 2005 3:49 PM

Navigation menu