Fujitsu Client Computing WL0024 PORTABLE PC LIFEBOOK T SERIES WITH 62205ANHMW WLAN User Manual Stork T901
Fujitsu Limited PORTABLE PC LIFEBOOK T SERIES WITH 62205ANHMW WLAN Stork T901
Contents
- 1. User Manual
- 2. Updated User Manual for CRN99288
- 3. Updated manual
User Manual
![1 - User’s GuideLearn how to use your Fujitsu LIFEBOOK T901 Tablet PCDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-1.png)
![1 Copyright and Trademark InformationFujitsu America, Inc. has made every effort to ensure the accuracy and completeness of this document; however, as ongoing developmentefforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.Fujitsu, the Fujitsu logo, and LIFEBOOK are registered trademarks of Fujitsu Limited.Intel, Intel Core, Centrino, and Intel Centrino Pro are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.PCMCIA is a trademark of the Personal Computer Memory Card International Association.Bluetooth is a trademark of Bluetooth SIG, Inc., USA.OmniPass is a trademark of Softex, Inc.PowerDirector, PowerDVD, MakeDisc, and YouCam are trademarks of CyberLink Corp.Roxio is a trademark of Sonic Solutions.Adobe and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.Norton and Norton Internet Security are trademarks or registered trademarks of Symantec Corporation in the United States and othercountries.All other trademarks mentioned herein are the property of their respective owners.© Copyright 2011 Fujitsu America, Incorporated. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu. B6FJ-5851-01ENZ0-00DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-2.png)
![2 - LIFEBOOK T901 Tablet PC WARNINGHANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD,A CHEMICAL KNOWN TO THESTATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.WASH HANDS AFTER HANDLING.DECLARATION OF CONFORMITYaccording to FCC Part 15Responsible Party Name: Fujitsu America, IncorporatedAddress: 1250 E. Arques Avenue,Sunnyvale, CA 94085Telephone: (408) 746-6000Declares that product: Base Model Configuration:LIFEBOOK T901 Tablet PCComplies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:(1) This device may not cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-3.png)
![Copyright and Trademark Information 3IMPORTANT SAFETY INSTRUCTIONS This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 19 VDC, with a current of 4.22 A (80 W).When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:•CAUTION - HOT SURFACE: The bottom of this notebook computer can become hot when used for long periods of time. When using this notebook, take caution to limit long term or continuous use while resting it on exposed skin, such as the lap.•Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.•Avoid using a modem during an electrical storm. There may be a remote risk of electric shock from lightning.•Do not use a modem to report a gas leak in the vicinity of the leak.•Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.•To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord.•For TV tuner use: To protect from overvoltages and transients on the Cable Distribution System, make sure that the outer shield of the coaxial cable is connected to earth (grounded) at the building premise as close to the point of cable entrance as practicable, as required per NEC Article 820.93, ANSI/NFPA 70: 2005. If you have questions about your CATV installation, contact your service provider.SAVE THESE INSTRUCTIONSFor Authorized Repair Technicians OnlyDANGER OF EXPLOSION IF LITHIUM (CLOCK)BATTERY IS INCORRECTLY REPLACED. REPLACE ONLYWITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USEDBATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTION.FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,REPLACE ONLY WITH THE SAME TYPE ANDRATING FUSE.+AC adapter output polarity:](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-4.png)
![4 - LIFEBOOK T901 Tablet PC Recycling your batteryOver time, the batteries that run your mobile computer will begin to hold a charge for a shorter amount of time; this is a natural occurrence for all batteries. When this occurs, you may want to replace the battery with a fresh one*. If you replace it, it is important that you dispose of the old battery properly because batteries contain materials that could cause environmental damage if disposed of improperly.Fujitsu is very concerned with environmental protection, and has enlisted the services of the Rechargeable Battery Recycling Corporation (RBRC)**, a non-profit public service organization dedicated to protecting our environment by recycling old batteries at no cost to you.RBRC has drop-off points at tens of thousands of locations throughout the United States and Canada. To find the location nearest you, go to www.RBRC.org or call 1-800-822-8837.If there are no convenient RBRC locations near you, you can also go to the EIA Consumer Education Initiative website (http://EIAE.org/)and search for a convenient disposal location.Remember – protecting the environment is a cooperative effort, and you should make every effort to protect it for current and futuregenerations.* To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site at www.shopfujitsu.com in the US orwww.fujitsu.ca/products/notebooks in Canada.** RBRC is an independent third party to which Fujitsu provides funding for battery recycling; RBRC is in no way affiliated with Fujitsu.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-5.png)
![ContentsCopyright and Trademark InformationIMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . 3PrefaceAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Getting to Know Your LIFEBOOKOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Locating the Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Top Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Left-Side Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Right-Side Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Back Panel Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Bottom Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28External Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Battery Charging Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-6.png)
![2 Battery Level Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Opening the Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Using the System as a Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Adjusting Display Panel Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Touchpad/Active Digitizer/Touchscreen. . . . . . . . . . . . . . . . . . . . . . . . . . . 40Using the Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Active Digitizer Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Using the Optional Capacitive Touchscreen . . . . . . . . . . . . . . . . . . . . . . . 49Installing a Pen Tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Controlling the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Modular Bay Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Removing and Installing Modular Devices . . . . . . . . . . . . . . . . . . . . . . . . 53LIFEBOOK Security/Tablet PC Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 55Security Button Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Pre-logon button functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Post-logon button functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Changing Tablet PC Button Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Setting up LIFEBOOK Security Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Using Your LIFEBOOK Security Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . 63Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Uninstalling/Re-installing the Security Panel Application. . . . . . . . . . . . . 65DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-7.png)
![3Getting Started with Your LIFEBOOKPower Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Connecting the Power Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Starting Your LIFEBOOK Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Hard Disk Drive Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Booting the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Starting Windows the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing ClickMe!75Fujitsu Driver Update Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Power/Suspend/Resume Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Hibernation (Save-to-Disk) Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Windows Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Restarting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Powering Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82User-Installable FeaturesLithium ion Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Recharging the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Memory Stick/Secure Digital Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Installing Memory Stick/SD Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Removing A Memory Stick/SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-8.png)
![4ExpressCards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Installing ExpressCards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Removing ExpressCards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Smart Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Installing Memory Upgrade Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Removing a Memory Upgrade Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Checking the Memory Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Internal LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Modem (RJ-11) Jack*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98Port Replicator Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99IEEE 1394 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101Microphone Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101External Video Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101Troubleshooting Your LIFEBOOKTroubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Identifying the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105Power On Self Test Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Restoring Your Pre-installed Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122Re-installing Individual Drivers and Applications . . . . . . . . . . . . . . . . . . . 122Restoring the Operating System for Windows . . . . . . . . . . . . . . . . . . . . . . 123Automatically Downloading Driver Updates . . . . . . . . . . . . . . . . . . . . . . . 126DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-9.png)
![5Care and MaintenanceCaring for your LIFEBOOK Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . 128Cleaning your LIFEBOOK Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Cleaning the dust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132Storing your LIFEBOOK Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133Traveling with your LIFEBOOK Tablet PC . . . . . . . . . . . . . . . . . . . . . . . 134Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135Media Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136ExpressCards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138System SpecificationsSpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140Digitizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141Mass Storage Device Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141Modular Bay Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146Popular Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Learning About Your Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-10.png)
![6GlossaryRegulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168FCC NOTICES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168DOC (INDUSTRY CANADA) NOTICES . . . . . . . . . . . . . . . . . . . . . . . . 170Appendix A: WLAN User’s Guide FCC Regulatory Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Regulatory Notes and Statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Before Using the Optional Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . 176Wireless LAN Device Covered by this Document. . . . . . . . . . . . . . . . . . . 176Characteristics of the WLAN Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176Wireless LAN Modes Using this Device . . . . . . . . . . . . . . . . . . . . . . . . . . 177Deactivating/Disconnecting the WLAN Device . . . . . . . . . . . . . . . . . . . . 179Deactivation Using the Wireless On/Off Switch . . . . . . . . . . . . . . . . . . . . 180Disconnection Using the Icon in the Taskbar. . . . . . . . . . . . . . . . . . . . . . . 180Activating the WLAN Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180Configuring the Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Configuring the WLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Connection to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Troubleshooting the WLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183WLAN Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185Using the Bluetooth Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187What is Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Where to Find Information About Bluetooth . . . . . . . . . . . . . . . . . . . . . . . 187DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-11.png)
![7Appendix B: Fingerprint Sensor DeviceIntroducing the Fingerprint Sensor Device . . . . . . . . . . . . . . . . . . . . . . . . 189Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190Installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190User Enrollment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195Configuring OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202OmniPass Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206Appendix C: Using Intel® Wireless DisplayUsing the Wireless Display technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208Starting the WiDi application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209Index](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-12.png)
![8 PrefaceAbout This GuideThe LIFEBOOK T901 Tablet PC from Fujitsu America is a powerful convertible computer. It can be used either as a standard notebook using keyboard input, or in tablet configuration using pen input. It is powered by the new 2nd Generation Intel® Core™ Processor, has a built-in color display with either an active digitizer or optional dual digitizer, and brings the computing power of desktop personal computers (PCs) to a portable and versatile environment.This manual explains how to operate your LIFEBOOK T901 Tablet PC’s hardware and pre-installed system software. Conventions Used in the GuideKeyboard and on-screen keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].Pages with additional information about a specific topic are cross-referenced within the text.For example: (“See Installation Procedure on page 43”.) Note that all cross-references are linked to the referenced items, so by clicking the link, you will automatically go to the referenced item or page.On-screen menu items appear in bold. Example: “Click Fujitsu Menu, and select your choice”.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-13.png)
![9 - About This GuideFujitsu Contact InformationService and SupportYou can contact Fujitsu Service and Support in the following ways:•Toll free: 1-800-8Fujitsu (1-800-838-5487)•Website: http://www.computers.us.fujitsu.com/supportBefore you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:•Product name•Product configuration number•Product serial number•Purchase dateTHE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OFTHE SUBJECT MATERIAL.THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOURCOMPUTER,OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATIONCAREFULLY.THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU,YOURLIFEBOOK TABLET PC, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-14.png)
![10 - About This Guide•Conditions under which the problem occurred•Any error messages that have occurred•Type of device connected, if anyFujitsu Shopping OnlineYou can go directly to the online by going to the website at: www.shopfujitsu.com.Limited WarrantyYour LIFEBOOK T901 Tablet PC is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your Tablet PC for the Limited Warranty period and terms and conditions.YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-15.png)
![11 Chapter 1 Getting to Know Your LIFEBOOKOverviewThis section describes the components of your Fujitsu LIFEBOOK T901 Tablet PC. We strongly recommend that you read it before using your Tablet PC – even if you are already familiar with notebook computers.Figure 1. Fujitsu LIFEBOOK T901 Tablet PCDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-16.png)
![12 - Locating the Controls and ConnectorsLocating the Controls and ConnectorsConnectors and peripheral interfaces on the LIFEBOOK T901 Tablet PC and the optional port replicator allow you to connect a variety of devices. Specific locations are illustrated in Figures 2 through 6. The table below provides a short description of each icon on the LIFEBOOK T901 Tablet PC and/or optional port replicator. Each of the icons is either molded into or printed on the Tablet PC or port replicator chassis.Connection Tablet PC IconPurposeDC in connector Connect an external power source such as the AC adapter or auto/airline adapter. SD Card/Memory Stick SlotThe Secure Digital (SD) card/Memory Stick slot allows you to insert a flash memory card for data storage. Flash memory cards allow you to transfer data to and from a variety of different digital devices.Smart Card Slot A dedicated Smart Card slot allows you to insert a Smart Card on which you can store such data as medical information or electronic “cash”.USB Port Connect Universal Serial Bus devices to the Tablet PC. Note that USB ports with a black tab in the center are for 2.0 or 1.1 compliant USB devices; those with a blue tab are for USB 3.0 devices.USB Port with Anytime USB Charge Connect Universal Serial Bus 2.0 or 1.1 compliant USB devices. This port can also be used to charge USB devices whether the system is powered on or not.Microphone Jack Connect an external microphone. The internal microphone is disabled when you plug in an external microphone. Headphone Jack Connect stereo headphones or powered external speakers. The internal speaker is disabled when you plug in external headphones or powered speakers. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-17.png)
![13 - Locating the Controls and ConnectorsHDMI Port The HDMI port allows you to connect compatible digital devices with your computer (such as a high-definition television or AV receiver).Security lock slot The security slot allows you to secure the Tablet PC using compatible locking devices.Suspend/ Resume buttonThe Suspend/Resume button allows you to suspend Tablet PC activity without powering off, resume your Tablet PC from suspend mode, and power on the system when it has been shut down from Windows. Local Area Network (LAN)The LAN (RJ-45) jack is used to connect the internal 10/100/1000* Base-T/Tx Ethernet to a Local Area Network (LAN) in your office or home, or broadband devices such as a cable modem, DSL, or satellite Internet. *1000 Mbps, commonly referred to as Gigabit Ethernet.Wireless Device On-Off SwitchThe Wireless Device switch allows you to turn power to the optional wireless devices on and off.External Video portThe external video port allows you to connect an external monitor or LCD projector to your computer.Digital Video InterfaceThe DVI-D port on the optional port replicator allows you to connect a flat-panel LCD monitor or television that is equipped with a DVI-D port for ultra-crisp digital images and graphics.IEEE1394 port The IEEE 1394 jack allows you to connect IEEE 1394 (Firewire) devices such as digital video cameras and external hard drives to your Tablet PC.Connection Tablet PC IconPurposeDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-18.png)
![14 - Locating the Controls and ConnectorsFigure 2. LIFEBOOK Tablet PC with display openDisplay PanelStatus KeyboardLIFEBOOK Security/Power/Suspend/Tablet PC ButtonsResume SwitchTouchpad Indicator PanelBuilt-inMicrophoneFingerprint SensorStatus Indicator PanelWireless Device On/Off SwitchCursor ControlOptional Web CamDisplay LatchWeb Cam Access LED Stereo SpeakersBuilt-in MicrophoneLatch ButtonHeadphoneMicrophoneJackJackAmbient Light SensorWireless DeviceAntennaDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-19.png)
![15 - Locating the Controls and ConnectorsTop ComponentsThe following is a brief description of your LIFEBOOK Tablet PC’s top components. Display LatchThe display latch is used to secure the tablet PC display when it is closed.Web CameraThe optional 1.3 megapixel web cam can be used to take pictures of yourself to send over the internet Web Cam Access LEDThe web cam access LED indicates when the web camera is activated.Wireless WAN AntennaThe Wireless Wide Area Network (WWAN) antenna allows you to communicate wirelessly with an optional WWAN device from virtually any location.Display PanelThe display panel is a color LED panel with backlighting for the display of text and graphics. There are two different displays available: an active digitizer that is used with a stylus, and a dual digitizer that can be used with either a stylus or your fingers. Dual Stereo SpeakersThe built-in dual speakers provide stereo sound.LIFEBOOK Security/Tablet PC ButtonsThe LIFEBOOK Security/Tablet PC Buttons provide password security for your system, as well as one-touch application launch capability. See “LIFEBOOK Security/Tablet PC Buttons” on page 50.Dual Built-in MicrophonesThe built-in microphones allows you to record voice and annotations. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-20.png)
![16 - Locating the Controls and ConnectorsPower/Suspend/Resume SwitchThe Power/Suspend/Resume button allows you to suspend Tablet PC activity without powering off, resume your LIFEBOOK Tablet PC from sleep mode, and power on your Tablet PC when it has been shut down from Windows. See “Power/Suspend/Resume Button” on page 70.Status Indicator PanelsThe Status Indicator Panels display symbols that correspond to specific components of your Tablet PC. Status indicators are located in two locations: on the front edge of the system (system status indicators) and below the application buttons (button status indicators). See “Status Indicator Panel” on page 26.KeyboardA full-size keyboard with dedicated Windows keys. See “Keyboard” on page 33.Display Latch ButtonThe display latch button allows you to unlatch the front of the display from the case.Wireless Device On/Off SwitchThe wireless device on/off switch is used to turn on and off the optional wireless devices. Switching the device off when not in use will help to extend battery life. See “Activating the WLAN Device” on page 167.Microphone JackThe microphone jack allows you to connect an external mono microphone. See “Microphone Jack” on page 91.Headphone JackThe headphone jack allows you to connect headphones. See “Headphone Jack” on page 91.Touchpad Cursor ControlThe touchpad cursor control offers an additional method for moving the cursor. See “Touchpad/Active Digitizer/Touchscreen” on page 36.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-21.png)
![17 - Locating the Controls and ConnectorsFingerprint SensorThe fingerprint sensor device allows you to log onto your system and password-protected websites and applications by swiping your finger over the sensor. See “Introducing the Fingerprint Sensor Device” on page 175.Ambient Light SensorThe ambient light sensor measures the light in which the computer is operating and automatically adjusts the brightness of the display to suit the lighting conditions. See “Enabling/Disabling Ambient Light Sensor (Windows 7 only)” on page 38.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-22.png)
![18 - Locating the Controls and ConnectorsFigure 3. LIFEBOOK Tablet PC left-side panelLeft-Side Panel ComponentsThe following is a brief description of your LIFEBOOK Tablet PC’s left-side components. ExpressCard SlotThe ExpressCard Slot allows you to install an ExpressCard. Card. See “ExpressCards” on page 81.ExpressCard Eject ButtonThe ExpressCard eject button is used for removing an ExpressCard from the slot.DC Power JackThe DC power jack allows you to plug in the AC adapter to power your LIFEBOOK Tablet PC and charge the internal Lithium ion battery.Air VentsThe air vents are used to cool the system to prevent overheating.Air VentsExpressCard SlotSmart Card SlotExpressCard Eject ButtonDC Power Jack USB 3.0 PortIEEE 1394 Jack Memory Stick/SD Card SlotHDMI PortDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-23.png)
![19 - Locating the Controls and ConnectorsHDMI PortThe HDMI port is used to connect compatible digital devices with your computer (such as a high-definition television or AV receiver). See “HDMI Port” on page 103.IEEE 1394 (4-pin) JackThe 4-pin 1394 jack is used to connect between your Tablet PC and an IEEE 1394 peripheral such as a digital video camera for fast file transfer. See “IEEE 1394 Port” on page 90.USB 3.0 PortThe USB 3.0 port allows you to connect Universal Serial Bus devices. USB 3.0 transfers data at up to 5Gbps and is backward-compatible with USB 1.1 and 2.0 devices, which transfer data at up to 12 Mbps and 480 Mbps, respectively. See “Universal Serial Bus Ports” on page 67.Memory Stick/SD Card SlotThe Memory Stick/SD card slot allows you to install a Memory Stick or a Secure Digital (SD) card for data storage. This architecture allows you to transfer data from a variety of different digital devices. See“Installing Memory Stick/SD Cards” on page 80.Smart Card SlotA dedicated Smart Card slot is provided on your Tablet PC. Smart Cards are the same size and shape as a credit card, but they contain embedded integrated circuits. See “Smart Card Reader” on page 83. To use the embedded Smart Card Reader, you must purchase optional third-party software for installation.TO PROTECT YOUR TABLET PC FROM DAMAGE AND TO OPTIMIZE PERFORMANCE,BE SURE TO KEEPALL AIR VENTS UNOBSTRUCTED,CLEAN,AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODICCLEANING,DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED.DO NOT OPERATE THE TABLET PC IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED,SUCH AS INTIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-24.png)
![20 - Locating the Controls and ConnectorsFigure 4. LIFEBOOK Tablet PC right-side panel Right-Side Panel ComponentsThe following is a brief description of your LIFEBOOK Tablet PC’s right-side components. Pen GarageThe pen garage is used to store the pen (also called a “stylus”) when not in use.The pen is used as the interface with the active digitizer display.Pen Tether Attachment PointThe pen tether attachment point is designed to securely hold a pen tether to prevent loss of the pen. See “Installing a Pen Tether” on page 46 for additional information.Anti-theft Lock SlotThe anti-theft lock slot allows you to attach an optional physical lock down device.Modular BayThe Modular Bay can accommodate one of the following devices. See “Modular Bay Devices” on page 48.•Modular Dual-Layer Multi-Format DVD Writer Modular Bay DevicePen Tether Attachment PointPen Garage Modular Bay Eject LeverDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-25.png)
![21 - Locating the Controls and Connectors•Modular 2nd hard disk drive•Modular Lithium ion battery•Weight SaverModular Bay Eject LeverThe Modular Bay Eject Lever allows you to release the modular bay device so that it can be removed. See “Modular Bay Devices” on page 48.](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-26.png)
![22 - Locating the Controls and ConnectorsFigure 5. LIFEBOOK Tablet PC back panelBack Panel ComponentsFollowing is a brief description of your LIFEBOOK Tablet PC’s back panel components. Gigabit LAN (RJ-45) JackThe internal LAN (RJ-45) jack is used for an internal Gigabit (10Base-T/100Base-Tx/1000Base-T) Ethernet LAN connection. See “Internal LAN (RJ-45) Jack” on page 88.Anti-theft Lock SlotThe anti-theft lock slot allows you to attach an optional physical lock down device.Gigabit LAN USB 2.0 PortAir VentsExternalAnti-Theft Lock Slot Video Port USB 2.0 Port with(RJ-45) JackAir Vents Air Vents Air VentsAnytime USB ChargeSIM Card Slot(behind door)(behind door)DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-27.png)
![23 - Locating the Controls and ConnectorsSIM Card SlotThe SIM Card Slot is used to install an optional Wireless Wide Area Network (WAN) card.Air VentsThe air vents allow air to circulate through the system to cool down the components.USB 2.0 PortsThe USB 2.0 ports allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480 Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 1 2Mbps. See “Universal Serial Bus Ports” on page 89. Note that the USB 2.0 port towards the right has Anytime USB Charge capability, which allows you to charge a USB device whether or not the system is powered on.External Video PortThe external monitor port allows you to connect an external monitor or LCD projector. See “External Video Port” on page 91.TO PROTECT YOUR TABLET PC FROM DAMAGE AND TO OPTIMIZE PERFORMANCE,BE SURE TO KEEPALL AIR VENTS UNOBSTRUCTED,CLEAN,AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODICCLEANING,DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED.DO NOT OPERATE THE TABLET PC IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED,SUCH AS INTIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-28.png)
![24 - Locating the Controls and ConnectorsFigure 6. LIFEBOOK Tablet PC bottom panelBottom ComponentsThe following is a brief description of your LIFEBOOK Tablet PC’s bottom panel components. Battery LatchesThe battery latches are used to secure the Lithium ion battery in the battery bay.Lithium ion Battery BayThe battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery. See “Lithium ion Battery” on page 74.Memory UpgradeLithium ionPort ReplicatorBattery BayAir VentsBattery LatchBattery LatchConnectorCleanable Dust FilterCompartment DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-29.png)
![25 - Locating the Controls and ConnectorsMemory Upgrade CompartmentYour Tablet PC comes with high speed Double Data Rate 3 Synchronous Dynamic RAM (DDR3 1066 MHz SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your Tablet PC, thus improving overall performance. See “Memory Upgrade Module” on page 84. Under normal circumstances, it should not be necessary to open this compartment.Air VentsThe air vents allow air to circulate through the system to cool down the components.Cleanable Dust FilterThe dust filter is used to help remove dust and dirt fin your system. See “Cleaning the dust filter” on page 124.Port Replicator ConnectorThis connector allows you to connect the optional Port Replicator to your Tablet PC. TO PROTECT YOUR TABLET PC FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE,BE SURE TOKEEP ALL AIR VENTS UNOBSTRUCTED,CLEAN,AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODICCLEANING,DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED.DO NOT OPERATE THE TABLET PC IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED,SUCH AS INTIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-30.png)
![26 - Status Indicator PanelFigure 7. Status Indicator PanelStatus Indicator PanelThere are two Status Indicator Panels on your notebook: on the left front and under the button set. The Status Indicator Panels display symbols and associated LEDs that correspond to specific components of your Tablet PC. These symbols tell you how each of those components is operating.(Figure 7)Power Indicator•The Power indicator symbol shows whether your system is operational. It has several different states, each of which tells you what mode your Tablet PC is in at that time.•Steady On: This means that there is power to your Tablet PC and that it is ready for use.•Flashing: This means that your Tablet PC is in Sleep mode.•Steady Off: This means that your system is either in Hibernate mode, or that your Tablet PC has been turned off.12Optical/Hard NumLkCapsLkScrLkBattery 1 LevelBattery 2 LevelBattery ChargingPower IndicatorSecurityDrive AccessDRAFTDRADRRRRRR](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-31.png)
![27 - Status Indicator PanelIf you are charging your battery, the Power indicator symbol will remain on even if your LIFEBOOK Tablet PC is shut off. Even if the system was shut down from Windows, the Power indicator symbol will remain on if you have an adapter connected.Battery Charging IndicatorsThe Battery Charging and Battery Level indicators state whether the Lithium ion battery (Battery 1) or the optional modular battery (Battery 2) are installed and charging. Battery Level IndicatorThe Battery Level indicators display the charge level of the indicated battery pack, as follows:•Blue, solid: Battery is between 50% and 100% charged.•Orange, solid: Battery is between 13% and 49% charged.•Red, solid: Battery is between 0% and 12% charged.•Orange, blinking: Blinks during battery status measurement (Four seconds after the battery is installed).•Red, blinking: There is a problem with the battery.•Off: There is no battery installed.• If the battery pack is installed while the power is turned off, the battery level indicator will display the charge level for five seconds after it blinks orange.•If the AC adapter is not connected or the battery pack is not fully charged when the computer is switched to sleep mode, the indicator will blink. The LED blinks at the rate of one second on/five seconds off. •Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged.•A shorted battery is damaged and must be replaced.111 2DRAFTLIFEBOOKLIFEBOO](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-32.png)
![28 - Status Indicator Panel Hard Drive/Optical Drive Access IndicatorThe Hard Drive/Optical Drive Access indicator shows whether your internal hard drive or optical drive are being accessed is being accessed. Security IndicatorThe Security Indicator flashes (if a password was set) when the system resumes from Off or Sleep modes. You must enter the password that was set in the Security Panel before your system will resume operation. NumLk IndicatorThe NumLk indicator states that the integral keyboard is set in ten-key numeric keypad mode. CapsLock IndicatorThe CapsLock indicator states that your keyboard is set to type in all capital letters. ScrLk IndicatorThe ScrLk indicator states that your scroll lock is active. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-33.png)
![29 - Display PanelFigure 8. Opening the Display PanelDisplay PanelYour LIFEBOOK T901 Tablet PC contains an LED display panel that is backlit for easier viewing in bright environments. The convertible design of your Tablet PC allows you to open the display fully, rotate it in either direction 180 degrees, and lay it face up on the keyboard. This allows you to use the system as a tablet, much as you would a pad of paper.Opening the Display PanelPress the latch button and lift the display backwards, (being careful not to touch the screen with your fingers), until it is at a comfortable viewing angle. (Figure 8)Latch ButtonDisplay LatchDisplay PanelDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-34.png)
![30 - Display PanelUsing the System as a TabletIf you would like to use the system as a tablet, perform the following steps. 1Press the latch button and lift the display until it is perpendicular to the keyboard. (Figure 10).2When the display is perpendicular to the keyboard, rotate it 180 degrees in either direction (Figure 11) so that it is facing backwards.3Holding the top edge of the display panel, pull it forward until it is lying nearly atop the keyboard.To return the system to notebook configuration, repeat steps 3 and 2.•The display can be rotated in either direction, but when returning the system to notebook mode, be sure to turn it back to its original position (i.e., the reverse of how you turned it when you opened it. Turning the display in the incorrect direction could cause hinge damage.•In the following step, be sure to position the display perpendicular to the keyboard, otherwise the keyboard or display cover could get scratched.4Push the latch towards the display (See “A” in Figure 9). The latch will pivot so the top latch disappears, and the bottom latch appears (See “B” in Figure 9). Holding the latch down, lay the display flush against the system so that the latch engages. You can now use your system as a tablet. 5Lay the display flush against the system so that the latch engages. You can now use your system as a tablet. (Figure 12) Figure 9. Latching/unlatchingTop latchBottom latchDisplay SideABDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-35.png)
![31 - Display PanelHolding the Tablet PCYour computer can be used in tablet configuration in four different orientations (Figure 12). Letters associated with each orientation refer to the position of the system when the arrow isfacing up.•(A) Portrait Orientation: Hold the system with the display positioned vertically with the latch on the left.•(B) 2nd Portrait Orientation: Hold the system with the display positioned vertically with the latch on the right.•(C) Landscape Orientation: Hold the system with the display positioned horizontally with the latch on the top.•(D) 2nd Landscape Orientation: Hold the system with the display positioned horizontally with the latch on the bottom.Figure 10. Fully Open Display Figure 11. Rotating Display Figure 12. Tablet ModeABCDDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-36.png)
![32 - Display PanelAdjusting Display Panel BrightnessOnce you have turned on your Tablet PC, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are three ways to adjust the brightness: keyboard, power management utility, and Fujitsu Menu. Using Keyboard to Adjust BrightnessAdjusting the brightness using the keyboard changes the system setting (i.e., the settings you make via the function keys automatically changes the brightness settings in the system’s Pen and Tablet Settings). •[Fn+F6]: Pressing repeatedly will lower the brightness of your display.•[Fn+F7]: Pressing repeatedly will increase the brightness of the display.Using Power Management to Adjust BrightnessTo adjust brightness with the power management utility:Click Start -> Control Panel. In View by:, select one of the icon views. Select Display, then click Adjust brightness in the left pane. Drag the Screen brightness: slider to the left or right, depending upon your preference.Using the Fujitsu Menu to Adjust BrightnessTo adjust brightness using the Fujitsu menu, click on the Fujitsu Menu icon in the system tray in the lower right corner of the screen. (You can also open the Fujitsu menu by clicking the [Fn] button twice in succession.) Scroll down to the Mobility Center and double-click it, then double-click the icon adjacent to Display brightness. Set the screen brightness sliders for On battery and Plugged in scenarios.IF USING AC POWER,YOUR BRIGHTNESS SETTING IS SET TO ITS HIGHEST LEVEL BY DEFAULT. IF USINGBATTERY POWER,YOUR BRIGHTNESS SETTINGS IS SET TO APPROXIMATELY MID-LEVEL BY DEFAULT.THE HIGHER THE BRIGHTNESS LEVEL,THE MORE POWER THE TABLET PC WILL CONSUME AND THEFASTER YOUR BATTERIES WILL DISCHARGE. FOR MAXIMUM BATTERY LIFE,MAKE SURE THAT THEBRIGHTNESS IS SET AS LOW AS POSSIBLE.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-37.png)
![33 - KeyboardKeyboardFigure 13. KeyboardUsing the KeyboardYour Fujitsu LIFEBOOK Tablet PC has an integral 84-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys (Figure 13):Fn Key Start KeyFunction KeysNumeric Keypad Application Key Cursor Keys(surrounded by heavy line)](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-38.png)
![34 - Keyboard•Numeric keypad: Your Tablet PC allows certain keys to serve dual purposes, both as standard characters and as numeric and mathematical keys. The ability to toggle between the standard character and numeric keys is controlled through the [NumLk] key.•Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents. •Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running. •Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.Numeric KeypadCertain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] keys. Turning off the NumLk feature is done the same way. Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary functions. Windows KeysYour LIFEBOOK Tablet PC has two Windows keys, consisting of a Start key and an Application key. The Start key displays the Start menu. This button functions the same as your onscreen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows Help and Support documentation in the Start menu for additional information regarding the Windows keys.) Cursor KeysThe cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right). DRAFThddhd](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-39.png)
![35 - KeyboardFunction KeysYour LIFEBOOK Tablet PC has 12 function keys, F1 through F12. Functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. •The [Fn] key provides extended functions for the Tablet PC and is always used in conjunction with another key. •[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.•[Fn+F4]: Pressing [F4] while holding [Fn] will toggle the Quick Point feature on and off. Note that the [Fn+F4] combination only works if Manual Setting is selected in the BIOS. (See “BIOS Setup Utility” on page 66)•[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.•[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.•[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your LIFEBOOK Tablet PC.•[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your LIFEBOOK Tablet PC.•[Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, external monitor only, and both built-in display panel and external monitor.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-40.png)
![36 - Touchpad/Active Digitizer/TouchscreenTouchpad/Active Digitizer/TouchscreenFigure 14. Touchpad pointing deviceUsing the TouchpadThe touchpad is built into your LIFEBOOK Tablet PC. It is used to control the movement of the cursor to select items on your display panel. The touchpad is composed of a cursor control below the center of the keyboard, two buttons below it, and a scroll sensor on the right edge of the cursor control. The left button functions the same as a left mouse button while the right button has the same function as a right mouse button. When used with the cursor control, the scroll sensor allows you to scroll up and down a screen. The actual functionality of the buttons may vary depending on the application that is being used.Left ButtonRight ButtonCursor ControlScrollSensorDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-41.png)
![37 - Touchpad/Active Digitizer/TouchscreenClickingClicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the touchpad once. Figure 15. Clicking with buttonFigure 16. Clicking with TouchpadFigure 17. Right-clicking with buttonDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-42.png)
![38 - Touchpad/Active Digitizer/TouchscreenDouble-ClickingDouble-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and immediately release it. You can also perform the double-click operation by tapping lightly on the Touchpad twice. Figure 18. Double-clicking with buttonFigure 19. Double-clicking with Touchpad•IF THE INTERVAL BETWEEN CLICKS IS TOO LONG,THE DOUBLE-CLICK WILL NOT BE EXECUTED.•PARAMETERS FOR THE QUICK POINT CAN BE ADJUSTED FROM THE MOUSE DIALOG BOX LOCATED INTHE WINDOWS CONTROL PANEL.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-43.png)
![39 - Touchpad/Active Digitizer/TouchscreenDraggingDragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad. First, tap the Touchpad twice over the item you wish to move making sure to leave your finger on the pad after the final tap. Next, move the object to its new location by moving your finger across the Touchpad, and then release your finger. Figure 20. Dragging with buttonFigure 21. Dragging with TouchpadDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-44.png)
![40 - Touchpad/Active Digitizer/TouchscreenTouchpad Control AdjustmentThe Windows Control Panel allows you to customize your touchpad with selections made from within the Mouse Properties dialog box. There are three aspects of operation which you can adjust:•Buttons: This tab lets you set up the buttons for right or left handed operation, in addition to setting up the time interval allowed between clicks in double-clicking.•Pointers: This tab lets you set up the scheme for the cursor depending on its functionality.•Pointer Options: This tab lets you set up a relation between the speed of your finger motion and the speed of the cursor. It also allows you to enable a Pointer Trail for the cursor arrow.Using the Scroll WheelThe scroll wheel is located to the right of the touchpad (Figure 9). The wheel doesn’t actually turn, but you can easily move your finger around it in a circular motion to scroll though pages and lists, the same way you would with a scroll bar. The scroll wheel can also be used to zoom in and out on pictures. To do so, position the cursor on a picture and move your finger horizontally across the scroll wheel to enlarge and reduce the size of the picture.ScrollingUsing the scrolling strip allows you to navigate through a document quickly without using the window’s scroll bars. This is particularly useful when you are navigating through on-line pages. To scroll, slide your finger up and down the scroll strip on the right side of the cursor control pad. Note that when you are working in tablet mode, a second scroll strip is located adjacent to the display.Figure 22. Scrolling with the Scroll StripDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-45.png)
![41 - Touchpad/Active Digitizer/TouchscreenActive Digitizer DisplayFigure 24. Stylus FeaturesNOTE: Depending upon your system configuration, in addition to the active digitizer, you may also have a capacitive touch panel that responds to finger touch and gestures. (This configuration is called a “Dual Digitizer”.) For more information about the touchscreen, refer to “Using the Optional Capacitive Touchscreen” on page 45.The integrated active digitizer allows you to use the included stylus as a pointing device. You can use the stylus to click, double-click, right-click, drag items and icons, write text, or to draw and erase like a pen or pencil in applications that support this behavior, such as drawing or painting programs. The front half of the barrel button works the same as a right-click button. The back half of the barrel button and the eraser button on the end of the pen both act as erasers. If useing the eraser button, be sure to depress it by pressing it on the display in order to activate the eraser function. Figure 23. Using Active Digitizer DisplayRight-Click ToggleEraser ToggleEraser ButtonPen Tether Attachment PointDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-46.png)
![42 - Touchpad/Active Digitizer/Touchscreen•DO NOT USE EXCESSIVE FORCE WHEN TAPPING OR WRITING ON THE SCREEN WITH THE STYLUS.EXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR ACTIVE DIGITIZER.•TO PURCHASE ADDITIONAL OR REPLACEMENT STYLUSES,VISIT FUJITSU’S ACCESSORIES WEBSITE AT:WWW.SHOPFUJITSU.COM.Clicking on Active Digitizer DisplayTo left-click, touch the object you wish to select and then lift the stylus tip immediately. Figure 25. Clicking on the Active Digitizer DisplayFigure 26. Right-clicking Active DigitizerRight-Clicking on Active DigitizerRight-click can be accomplished by holding the front of the toggle button down while tapping on the screen. To change the settings for the right-click feature, go to Start -> Control Panel -> Hardware and Sound -> Pen and Touch. In the Pen Options tab, select “Press and Hold” then click the [Settings] button.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-47.png)
![43 - Touchpad/Active Digitizer/TouchscreenDouble-ClickingTo double-click, touch the item twice, and then immediately remove the stylus tip. Figure 27. Double-clicking the DisplayDraggingDragging means moving an item with the stylus by touching the screen, moving and then lifting the stylus. To drag, touch the Active Digitizer Display with your stylus on the item you wish to move. While continuing to touch the screen with the stylus, drag the item to its new location by moving the stylus across the screen, and then lifting the stylus to release it. Figure 28. Dragging on the Display](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-48.png)
![44 - Touchpad/Active Digitizer/TouchscreenCalibrating the Active Digitizer DisplayIn order to ensure accurate tracking between the stylus and cursor, you must run the Calibration Utility before you use the system for the first time, or after you change the display resolution.To run the calibration utility:1Go to Start -> Control Panel. 2Click Hardware and Sound, then select Tablet PC Settings3Under the Display tab, click the [Calibrate] button.(Note: If you have the optional capacitive touchscreen, you will need to click on either Pen input or Touch input, depending upon which method you want to calibrate.)4Adjust the display of your Tablet PC to a comfortable angle and find the (+) symbol in the upper-left corner of the display.5Depending upon whether you are calibrating pen input or touch input, firmly touch the screen with the stylus or your finger directly on the (+) symbol. Lift the stylus or your finger from the screen and the target will move to a different location on the screen.6Repeat step 4 until you have selected all of the (+) symbols.7Once you have selected all the symbols, press the [OK] button.8Touch the stylus or your finger to various points on the screen to verify that the screen is correctly calibrated. If you are not satisfied with the screen’s calibration, press the [Calibrate]) button to begin again.•THE FIRST TIME YOU PERFORM A CALIBRATION,THE SYSTEM DISPLAY SHOULD BE IN LANDSCAPEMODE. SUBSEQUENT CALIBRATIONS CAN BE PERFORMED IN LANDSCAPE OR PORTRAIT MODE.•THE FIRST TIME YOU CALIBRATE,THERE WILL BE 16 CALIBRATION POINTS;SUBSEQUENT CALIBRATIONSWILL REQUIRE ONLY FOUR CALIBRATION POINTS.DO NOT USE EXCESSIVE FORCE WHEN TAPPING ON THE SCREEN DURING CALIBRATION. USE OFEXCESSIVE FORCE COULD RESULT IN DAMAGE TO THE LED AND/OR TOUCH PANEL.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-49.png)
![45 - Touchpad/Active Digitizer/TouchscreenUsing the Optional Capacitive TouchscreenCertain configurations of this Tablet PC have an optional dual digitizer that allows you to use either the stylus or your finger(s) as a pointing device. This type of display also allows you to use “gestures” to perform such actions as scroll, zoom, and rotate.Right-clicking the touchscreenTo perform a right-click action using two fingers, press the first finger at the location you want to perform a right-click, then quickly tap and release the second finger on the screen.Gesture ModeTo initiate gesture mode, two fingers must touch the screen within one 10th of a second of each other. If the second finger touches the screen after one 10th of a second has elapsed, the second finger is ignored. Gesture mode ends when both fingers are removed from the screen. Note that if a gesture can’t be recognized, no action is taken. In that case, remove both fingers from the screen and try again.Scrolling GestureTo scroll through long documents or on a web page, place both fingers on the screen (one finger quickly followed by the second) and move them in parallel in the same direction; if only one finger moves, no scrolling will occur. You can scroll vertically or horizontally, depending upon the direction of the gesture.Zoom GestureThe zoom gesture is especially helpful when viewing pictures. To zoom in, place two fingers on the item you want to enlarge (one finger quickly followed by the second), then spread them away from each other. To zoom out, place two fingers on the item you want to reduce (one finger quickly followed by the second), then move them towards each other.•GESTURE SUPPORT IS DETERMINED BY THE APPLICATION IN USE.•THE STYLUS TAKES PRECEDENCE OVER FINGER TOUCH. IF THE STYLUS IS WITHIN ACTIVE RANGE OFTHE SCREEN,FINGER TOUCH WILL BE DISABLED.•WHEN ONE FINGER IS USED ON THE TOUCHSCREEN,IT BEHAVES IN THE SAME MANNER AS A STYLUS.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-50.png)
![46 - Touchpad/Active Digitizer/TouchscreenRotate GestureTo change the orientation of an object on the screen, place two fingers on the image you want to rotate (one finger quickly followed by the second), then move them in opposite directions (as if you were turning a knob). The direction the item turns is dependant upon the direction you move your fingers.Installing a Pen TetherTo prevent dropping or losing your pen, you should attach it to your system using the pen tether that is included with the system. To attach the pen tether to your Tablet PC, perform the following steps:1Attach the end of the pen tether with the smaller loop to your pen. To do so, push the end of the tether through the hole in the pen, then thread the opposite end of the tether through the loop.2Attach the end of the pen tether with the larger loop to the attachment point on your tablet. To do so, insert the end of the pen tether through the attachment point, then feed the pen through the large loop in the tether. Figure 29. Installing a Pen TetherDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-51.png)
![47 - Volume ControlVolume ControlYour Fujitsu LIFEBOOK Tablet PC has multiple volume controls which interact with each other. Controlling the VolumeThe volume can be controlled in several different ways:•Volume can be changed or muted from within the Volume Control in the system tray.•Volume can be controlled with the F8 and F9 functions keys. Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your Tablet PC. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your Tablet PC.•Volume can be changed by opening the Control Panel and selecting Windows Mobility Center. From there, you can either mute or adjust the sound in the Volume area.•Volume can be muted by pressing the [F3] key while holding down the [Fn] key. To restore audio, repeat the [Fn+F3] procedure.•Volume can be controlled by many volume controls that are set within individual applications.•Certain external audio devices you might connect to your system may have hardware volume controls.Each source discussed above puts an upper limit on the volume level that must then be followed by the other sources. We recommend that you experiment with the various volume controls to discover the optimal sound level.ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IFYOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL,THEHARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACHOTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO OFF,YOU WILL OVERRIDETHE EXTERNAL VOLUME CONTROL SETTING.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-52.png)
![48 - Modular Bay DevicesFigure 30. Modular BayModular Bay DevicesYour Fujitsu LIFEBOOK Tablet PC contains a Modular Bay. The Modular Bay can house an optical drive, a Lithium ion battery, a modular second hard disk drive and a weight saver. Your Modular Bay will have one of the following devices installed. •Modular Dual-Layer Multi-Format DVD Writer: This allows you to access movies, software, and audio DVD/CDs and record to DVD, CD, and DVD-RAM discs.•TBD - Modular Blu-ray™ RW Drive. This drive allows you to read from and write to Blu-ray discs.•Modular Lithium ion battery: This is a rechargeable battery that can be used to power your LIFEBOOK Tablet PC when an adapter is not connected.•Modular hard drive: This allows you to increase the storage capacity of your Tablet PC.•Weight Saver: This is used to fill the bay when no device is needed.Modular Bay YOU SHOULD NEVER LEAVE YOUR MODULAR BAY EMPTY WHEN THE TABLET PC IS IN OPERATION. IFLEFT EMPTY,DUST OR FOREIGN MATTER MAY ACCUMULATE INSIDE THE TABLET PC.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-53.png)
![49 - Modular Bay DevicesRemoving and Installing Modular Devices There are two ways to remove and install modular devices in the Modular Bay:•Cold-swapping: swapping devices while your LIFEBOOK Tablet PC is powered off.•Hot-swapping: swapping devices while your system is active using the Safely Remove Hardware icon from your system tray.Cold-swappingTo cold-swap modular devices in your Modular Bay follow these easy steps:1Close any open files and shut down your LifeBook notebook.2Pull out the Flexible Bay release latch. This will push your device out slightly, allowing you to remove it.3Slide your device out until it is clear of the bay. This will require light force.4Slide the device you are installing into your notebook until it clicks into place.5It is now safe to turn your notebook back on.6You can now access and use the device.Your Tablet PC will automatically detect the device and activate it within your system. The drive letters associated with the device will be created and listed under My Computer and Windows Explorer. Hot-swappingHot-swapping is provided through the Safely Remove Hardware utility. The icon for the utility appears in the system tray. Click on the icon and follow the on-screen instructions.Figure 31. Removing/Installing Modular DeviceModular Bay Release LatchDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-54.png)
![50 - LIFEBOOK Security/Tablet PC ButtonsFigure 32. LIFEBOOK T901 Tablet PC Security/Tablet PC Buttons LIFEBOOK Security/Tablet PC ButtonsA unique feature of your LIFEBOOK T901 Tablet PC is the array of Security and Tablet PC buttons. These buttons allow you to secure your Tablet PC from unauthorized use and to launch specific applications and functions with the touch of a button. Security Button FunctionsIf the security system is activated, upon starting your Tablet PC or resuming from Sleep, Hibernate, or shutdown mode, the security system will require you to enter a password code using the security buttons. After you enter the correct password, your system will resume operation. The five security/Tablet PC buttons are located on the bottom right-hand side of the display when it is configured to be used as a notebook. All five buttons are used when implementing security functions. Four of the buttons are used to enter the password; the fifth is used as an Enter button. See Table 1 for information about each Security button.1234ENTBnADRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-55.png)
![51 - LIFEBOOK Security/Tablet PC ButtonsTable 1. Security Panel Button FunctionsPre-logon button functionsAll five buttons can be used before logging on to Windows (i.e., when the Windows logon screen is displayed). Three of the buttons have secondary functions. See Table 2 for information about the pre-logon functions.<Tab>/<Shift><Tab>When you press the [Page Down] button when the system is pre-logon, each press of the button will act as if you had pressed the [Tab] key.When you press the [Fn] button then press and release the [Page Down] button, each press of the button will act as if you had pressed the [Shift]+[Tab] key combination.<Enter>/<Escape>When you press the [Page Up] button when the system is pre-logon, each press of the button will act as if you had pressed the [Enter] key.Button Icon System State Security Panel FunctionSystem is pre-boot or resuming from suspend Security Button 1Security Button 2Security Button 3Security Button 4Security Enter ButtonDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-56.png)
![52 - LIFEBOOK Security/Tablet PC ButtonsTable 2. Pre-logon Tablet PC Button FunctionsWhen you press the [Fn] button then press and release the [Page Up] button, each press of the button will act as if you had pressed the [Escape] key.Screen RotationThe screen rotation feature would normally be used when the system is configured as a tablet. When you would like to use the tablet as an eBook, for example, you would use the portrait orientation; when accessing spreadsheets or using the system as a notebook, you would more typically use landscape orientation.When the system is changed to tablet configuration, the orientation automatically changes to portrait mode by default.ButtonIcon System State Tablet PC Function Secondary Functions(Fn + Button)System is pre-logon (Windows logon screen is displayed) <Tab> <Shift><Tab><Enter> <Escape>Rotate screen NoneUsed to invoke secondary functionNoneCtl+Alt+Del Button NoneDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-57.png)
![53 - LIFEBOOK Security/Tablet PC ButtonsWhen you press the [Screen Rotation] button when the system is in pre-boot, the system screen orientation changes from portrait (vertical) to landscape (horizontal) or from landscape to portrait.Function / Fujitsu Menu Utility ButtonThe [Function] button works in conjunction with the other application buttons to provide additional functionality for the buttons. Refer to specific details above.Post-logon button functionsAll five buttons can be used after logging on to Windows. Four of the buttons have secondary functions. See Table 3 for information about each of the post-logon functions.Page Down / Application A ButtonWhen you press the [Page Down] button when the system is running, each press of the button will scroll the screen down one frame. This allows you to navigate quickly through large documents.When you press the [Fn] button then press and release the [Page Down/Application A] button, you will automatically start whichever program is assigned to the button. The default application for this button is Calculator. See “Changing Tablet PC Button Functions” on page 55 to select a different application for this button.Page Up / Application B ButtonWhen you press the [Page Up] button when the system is running, each press of the button will scroll the screen up one frame. This allows you to navigate quickly through large documents.THE SCREEN ORIENTATION DEFAULT CAN BE CHANGED BY GOING TO THE CONTROL PANEL ANDDOUBLE-CLICKING ON THE FUJITSU TABLET CONTROLS ICON AND SELECTING THE DESIRED SETTINGSIN THE DISPLAY PROPERTIES. AFTER CHANGING THE SETTINGS,SAVE THEM IN FUJITSU TABLETCONTROLS.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-58.png)
![54 - LIFEBOOK Security/Tablet PC ButtonsWhen you press the [Fn] button then press and release the [Page Up/Application B] button, you will automatically start whichever program is assigned to the button. The default application for this button is Microsoft Journal. See “Changing Tablet PC Button Functions” on page 55 to select a different application for this button.Table 3. Post-logon Tablet PC Button FunctionsScreen Rotation /Display Switching ButtonThe screen rotation feature would normally be used only when the system is configured as a tablet. When you would like to use the tablet as an eBook, for example, you would use the portrait orientation; when accessing spreadsheets or using the system as a notebook, you would more typically use landscape orientation.When the system is changed to tablet configuration, the orientation automatically changes to portrait mode by default. Button Icon System State Primary Tablet PC FunctionSecondary Functions(Fn + Button)System is post-logon (Windows desktop is displayed) Page Down User-defined Application A(Default = Calculator)Page Up User-Defined Application B(Default = MS Journal)Screen Rotation Display Switching:1. LED only2. CRT only3. Dual DisplaySecondary Function SelectionFujitsu Menu UtilityCtl+Alt+Del Button NoneDRAFTillil](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-59.png)
![55 - LIFEBOOK Security/Tablet PC ButtonsWhen you press the [Screen Rotation /Display Switching] button, the system screen orientation changes from portrait (vertical) to landscape (horizontal) or from landscape to portrait. Pressing the [Fn] button while pressing the [Screen Rotation] button will switch the display output in the following order: built-in display only, external display only, dual display.Function / Fujitsu Menu Utility ButtonThe [Function] button works in conjunction with the other application buttons to provide additional functionality for the buttons. Refer to specific details above.Pressing the [Fn] button twice in succession causes the Fujitsu Menu Utility to appear on your screen, allowing you to modify certain system settings.Ctl+Alt+Del ButtonPressing and holding the [Ctl-Alt-Del] button for up to 8 seconds launches the Logon screen or the Windows Task Manager.Changing Tablet PC Button FunctionsThe Application A and B buttons can be changed to launch a program or perform an action you select. By default, the Application A button launches the Calculator, and the Application B button launches MS Journal.To launch different applications or cause the Application A or B buttons to perform a specific action:1Double-click on the Tablet PC Settings icon in the Control Panel. THE SCREEN ORIENTATION DEFAULT CAN BE CHANGED BY GOING TO THE CONTROL PANEL ANDDOUBLE-CLICKING ON THE TABLET PC SETTINGS ICON AND SELECTING THE DESIRED SETTINGS IN THEDISPLAY TAB. AFTER CHANGING THE SETTINGS,SAVE THEM IN FUJITSU TABLET CONTROLS.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-60.png)
![56 - LIFEBOOK Security/Tablet PC Buttons2Select the Buttons tab and select the button you would like to change from the list.3Click [Change] and open the drop down list in the Press: field.4Select the action you would like the button to perform. If you want to launch a program, click on Start a Program, then browse to the location of the program.5Click [OK], then click [OK] again. The buttons will now perform the actions you have assigned to them.Setting up LIFEBOOK Security PanelWhen you receive your Tablet PC, the security panel application is pre-installed without any passwords. The following sections provide detailed information on your security panel, how to set, change or remove passwords.Numbered ButtonsUse these buttons to enter your password.Enter ButtonAfter entering the button strokes, push this button to enter the password into the Tablet PC. PasswordsThe user and supervisor password may be set on this Tablet PC. A supervisor password is typically the same for all tablets and notebooks in a work group, office, or company to allow for system management. Individual computers in a group environment should not use a common password. A password consists of one to five button strokes plus the enter button. A valid stroke consists of pushing one or up to four buttons simultaneously. The following are valid button strokes: •Pushing [4] by itself•Pushing [2] and [3] at the same time•Pushing [1], [2], and [4] at the same time•Pushing [1], [2], [3], and [4] at the same time](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-61.png)
![57 - LIFEBOOK Security/Tablet PC ButtonsThe following are valid passwords. The numbers within braces ({ }) are button strokes using more than one button. •{[2]+[3]}, [1], [Enter]•[4], [enter]•{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]Setting PasswordsWhen shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the supervisor password before the user password.Setting Supervisor PasswordYou must have set a supervisor password before setting any user passwords. The supervisor password can bypass the user password.1Go to the Start menu.2Click on Run.3Type in: C:\Program Files\Fujitsu\Security Panel Application\Supervisor\ FJSECS.EXE, then press [Enter]4Follow the on-screen instructions to set the Supervisor password.Setting User Password1Go to the Start menu.2Click on All Programs.3Click on Security Panel Application -> Security Panel Application.4Follow the on-screen instructions to set the user password.•THE PURPOSE OF SUPERVISOR PASSWORD IS TO BE ABLE TO BYPASS THE USER PASSWORD IN CASE THE USERPASSWORD IS FORGOTTEN. THE SUPERVISOR PASSWORD ALONE WILL NOT LOCK THE SYSTEM.•YOU MUST SET THE SUPERVISOR AND USER PASSWORDS FOR THE SECURITY PANEL TO WORK.DRAFTihih](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-62.png)
![58 - LIFEBOOK Security/Tablet PC ButtonsUsing Your LIFEBOOK Security PanelThe security lock feature is in effect both when the system resumes from Off, Sleep, or Hibernation state. You always need to push the Security Panel buttons to input the user password. Your system will not begin the boot sequence until you enter your supervisor/user password.From Off State1Turn on your system.2When the Security Indicator flashes, enter the password and press Enter button (e.g., if the password is 22222, first press Button 2 five times, then press the Enter button). The Tablet PC will boot to normal operation.From Sleep/Hibernation State1Press your Suspend/Resume button.2When the Security Indicator flashes, enter the password and press Enter button.The Tablet PC should resume normal operation.Incorrect Password EntryIf an invalid supervisor or user password is entered three times in succession, the system will “beep” for about one minute. If a valid password is entered within a minute (while system beeps), the beeping will stop and the Tablet PC will resume normal operation. If no password is entered or an invalid password is entered while the system beeps, the system will return to its previous locked state (sleep or off) and the Security Indicator will go off. To reactivate the Tablet PC after a password failure, you must press the Suspend/Resume button, then enter a correct password.YOU MAY CHANGE OR REMOVE THE SUPERVISOR OR USER PASSWORD BY REPEATING THE STEPSDEFINED ABOVE.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-63.png)
![59 - LIFEBOOK Security/Tablet PC ButtonsPrecautionsOpening and Closing the CoverBy default, closing the cover automatically places your system into Sleep mode. To change the default when the cover is closed:1Open the system Control Panel. If the display is in Category view, click one of the icon selections in the View by: field. Click on Power Options.2Click Choose what closing the lid does in the left pane.3Select the desired action for When I close the lid, then click the [Save changes] button.Low Battery OperationsIf your Tablet PC has a low battery, pushing the suspend/resume button only turns on the Security Indicator. Your Tablet PC does not unlock, the Security Indicator turns off after one minute. To resume normal operation, first attach a power supply to the Tablet PC. Then you may unlock the Tablet PC.Uninstalling/Re-installing the Security Panel ApplicationYou have two options when uninstalling the security panel application:•Remove passwords and uninstall the security panel application software. This will disable all security features.•Uninstall the security panel application with password still active. This will not allow any changes to the password. REMEMBER THE USER PASSWORD YOU SPECIFIED ON THE SECURITY PANEL APPLICATION. IF YOUFORGET THE PASSWORD YOU WILL NOT BE ABLE TO USE YOUR COMPUTER. THE SUPERVISORPASSWORD CAN OVERRIDE THE USER PASSWORD.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-64.png)
![60 - LIFEBOOK Security/Tablet PC ButtonsUninstalling the Security Panel Application SoftwareRemove passwords when User wants no password protection whatsoever and doesn’t want to give anybody the utility to set a password on their computer. In this case, if passwords (supervisor, user, or both) are set, the passwords must first be cleared BEFORE removing the application. To clear passwords, follow same procedure in SETTING PASSWORD CODES except this time, select REMOVE, enter current password then click Next. When asked to confirm select Ye s .Removing Security Panel Application with Passwords Still ActiveUsing this feature will not allow any changes to the password. User:1Go to Start -> Control Panel.2Open Programs and Features in the Control Panel. 3Select Security Panel for User in the list, and click Uninstall/Change.4When User Account Control box appears, click Continue.Supervisor:1Go to Start -> Control Panel.2Open Add or Remove Programs Properties in the Control Panel. 3Select the Security Panel for Supervisor in the list, and click Uninstall/Change.4When User Account Control box appears, click Continue.REMOVING THE APPLICATIONS DOES NOT REMOVE THE PASSWORD. IT SIMPLY REMOVES THE ABILITYTO CHANGE/ADD/REMOVE PASSWORDS. TO CHANGE YOUR PASSWORD YOU MUST REINSTALL THEAPPLICATION.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-65.png)
![61 - LIFEBOOK Security/Tablet PC ButtonsReinstalling the Security Panel ApplicationTo reinstall supervisor or user security application, you will need your Drivers and Applications CD. The Utilities\Security Panel Application folder contains two separate folders: Supervisor and User. The setup files for supervisor and user security applications are contained in those folders. 1Go to the Utilities\Security Panel Application\ Supervisor folder on the CD and double-click the setup.exe file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.2Go to the Utilities\Security Panel Application\User folder on the CD and double-click the setup.exe file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.Supervisor and user passwords can be set via Windows software using the FJSECS.exe and FJSECU.exe files, respectively. FJSECU.exe for the user password cannot run without first setting a supervisor password. You need to run FJSECS.exe first to set the supervisor password. Follow instructions under Setting Passwords on page 57.If you forget both passwords, please contact Fujitsu America Service and Support at 1-800-8FUJITSU (1-800-838-5487). Fujitsu America charges a service fee for unlocking a password-restricted Tablet PC. When calling please have a valid credit card and provide proof of ownership. You will then be given instructions on where to ship your Tablet PC. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-66.png)
![62 Chapter 2 Getting Started with Your LIFEBOOKPower SourcesYour Fujitsu LIFEBOOK Tablet PC has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.Connecting the Power AdaptersThe AC adapter or optional Auto/Airline adapter provides power for operating your Tablet PC and charging the batteries. Connecting the AC Adapter1Plug the DC output cable into the DC power jack of your LIFEBOOK Tablet PC.2Plug the AC adapter into an AC electrical outlet. Connecting the Optional Auto/Airline Adapter1Plug the DC output cable into the DC power jack on your Tablet PC.2Plug the Auto/Airline adapter into the cigarette lighter of an automobile, or, 3Plug the Auto/Airline adapter into the DC power jack on an airplane seat.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-67.png)
![63 - Power SourcesFigure 33. Connecting the AC AdapterSwitching from AC Adapter Power or the Auto/Airline Adapter to Battery Power1Be sure that you have at least one charged battery installed.2Remove the AC adapter or the Auto/Airline adapter.DC Power JackAC AdapterPower/Suspend/Resume SwitchTHE LITHIUM ION BATTERY IS NOT CHARGED UPON PURCHASE. INITIALLY,YOU WILL NEED TO CONNECTEITHER THE AC ADAPTER OR THE AUTO/AIRLINE ADAPTER TO USE YOUR TABLET PC.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-68.png)
![64 - Starting Your LIFEBOOK Tablet PCStarting Your LIFEBOOK Tablet PCPower OnPower/Suspend/Resume ButtonThe Power/Suspend/Resume button is used to turn on your LIFEBOOK Tablet PC from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your LIFEBOOK Tablet PC. To turn on your LIFEBOOK Tablet PC from its off state, slide the Power/Suspend/Resume switch, located above the keyboard to the right. When you are done working you can either leave your Tablet PC in Suspend mode, you can turn it off. See “Sleep Mode” on page 70 and “Powering Off” on page 73When you power on your LIFEBOOK, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your LIFEBOOK Tablet PC will emit an audio warning and/or an error message will be displayed. See “Power On Self Test Messages” on page 110. Depending on the nature of the problem, you may be able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.After satisfactory completion of the POST, your Tablet PC will load your operating system.WHEN YOU TURN ON YOUR LIFEBOOK TABLET PC BE SURE YOU HAVE A POWER SOURCE. THISMEANS THAT AT LEAST ONE BATTERY IS INSTALLED AND CHARGED,OR THAT THE AC OR AUTO/AIRLINEADAPTER IS CONNECTED AND HAS POWER.DO NOT CARRY YOUR LIFEBOOK TABLET PC AROUND WITH THE POWER ON OR SUBJECT IT TOSHOCKS OR VIBRATION,AS YOU RISK DAMAGING YOUR TABLET PC.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-69.png)
![65 - Starting Your LIFEBOOK Tablet PCBoot SequenceThe procedure for starting-up your Tablet PC is termed the Bootup sequence and involves your Tablet PC’s BIOS. When your LIFEBOOK Tablet PC is first turned on, the main system memory is empty, and it needs to find instructions to start up your Tablet PC. This information is in the BIOS program. Each time you power up or restart your Tablet PC, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your Tablet PC is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.The boot sequence is executed when:•You turn on the power to your LIFEBOOK Tablet PC.•You restart your Tablet PC from the Windows Shut Down dialog box.•The software initiates a system restart. Example: When you install a new application.Hard Disk Drive PasswordsTo provide additional security for your data, you can assign passwords to your hard disk drive(s). This feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about accessing the utility.NEVER TURN OFF YOUR LIFEBOOK TABLET PC DURING THE POWER ON SELF TEST (POST) OR ITWILL CAUSE AN ERROR MESSAGE TO BE DISPLAYED WHEN YOU TURN YOUR LIFEBOOK TABLET PC ONTHE NEXT TIME.See “Power On Self Test Messages” on page 110.REMEMBER YOUR PASSWORDS. IF YOU SET AND FORGET YOUR USER AND MASTER HARD DISKPASSWORDS, FUJITSU WILL NOT BE ABLE TO RESET IT. YOU MAY LOSE DATA AND HAVE TO REPLACEYOUR SYSTEM BOARD OR HARD DISK DRIVE.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-70.png)
![66 - Starting Your LIFEBOOK Tablet PCBIOS Setup UtilityThe BIOS Setup Utility is a program that sets up the operating environment for your LIFEBOOK Tablet PC. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your Tablet PC.The BIOS Setup Utility configures:•Device control feature parameters, such as changing I/O addresses and boot devices.•System Data Security feature parameters, such as passwords.Entering the BIOS Setup UtilityTo enter the BIOS Setup Utility do the following (or use the TrustedCore Menu, as detailed in the next section):1Turn on or restart your LIFEBOOK Tablet PC.2To enter the BIOS Setup Utility, press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.3Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings.Using the TrustedCore MenuWhen the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear. The TrustedCore Menu provides shortcuts to the following menus and information screens: •BIOS Setup•Diagnostic Screen•Boot Menu•Patent Information•System Information•Continue BootingDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-71.png)
![67 - Starting Your LIFEBOOK Tablet PCClicking on any of the fields will invoke the screen, information, or action described.The Boot Menu can also be invoked by pressing the [F12] key when the Fujitsu logo appears on the screen.BIOS GuideA guide to your Tablet PC’s BIOS is available online. Please visit our service and support website at http://www.computers.us.fujitsu.com/support, then select User’s Guides under Online Support. Select your Product, Series, and Model, then click [Go]. Under the Manuals tab, select the BIOS Guide. Booting the SystemWe strongly recommend that you not attach any external devices until you have gone through the initial power on sequence.When you turn on your Tablet PC for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.Starting Windows the First TimeAfter you boot up the system the first time and follow the instructions on the screen, you will eventually come to the Welcome window. After the Welcome window appears, the screen will black out for up to several minutes. This is normal. DO NOT ATTEMPT TO POWER DOWN THE SYSTEM AT THIS POINT. While the screen is blacked out, your system configuration is being set up and the necessary files are being installed. During the course of the first start up, you will need to read and accept the End User License Agreements (EULAs) for Microsoft and Fujitsu. •IF YOU REJECT THE TERMS OF THE LICENSE AGREEMENT YOU WILL BE ASKED TO REVIEW THE LICENSEAGREEMENT FOR INFORMATION ON RETURNING WINDOWS OR TO SHUT DOWN YOUR NOTEBOOK.•YOU CANNOT USE YOUR NOTEBOOK UNTIL YOU HAVE ACCEPTED THE LICENSE AGREEMENT. IF YOU STOP THEPROCESS YOUR NOTEBOOK WILL RETURN TO THE BEGINNING OF THE WINDOWS WELCOME PROCESS,EVEN IFYOU SHUT YOUR NOTEBOOK DOWN AND START IT UP AGAIN.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-72.png)
![68 - Starting Your LIFEBOOK Tablet PCSeveral additional windows will appear, prompting you to enter a name and description for your computer, an Administrator password, and a domain name. Read the instructions on the screens carefully and fill in the information as directed. Once you have pfinished with the setup, it is very important that you install ClickMe!, as detailed below.Installing ClickMe! The first time you boot up your system, you will see an icon called Click Me! in the Start menu. It is very important that you run the ClickMe! utility the first time you boot up in order to ensure that the necessary applications, utilities. and drivers are installed. When you click the Click Me! icon, your system will automatically create the related icons in the system tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access.When you install the ClickMe! utility, several applications and utilities are installed; this takes time. While ClickMe! is installing, the system may go into Suspend mode. If this should occur, slide the Power/Suspend/Resume button momentarily to wake the system up. Alternately, while ClickMe! is installing, slide your finger across the touchpad every few minutes to keep the system awake.BEFORE INSTALLING THE CLICKME!UTILITY,BE SURE THE WIRELESS LAN DEVICE IS ENABLED BYPUSHING THE WLAN/BLUETOOTH ON/OFF SWITCH TO THE ON POSITION.THERE MAY BE SOME THIRD-PARTY APPLICATIONS THAT DO NOT GET INSTALLED USING THE CLICKME!UTILITY. FOR MORE INFORMATION,REFER TO YOUR GETTING STARTED GUIDE.ClickMe!DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-73.png)
![69 - Starting Your LIFEBOOK Tablet PCRegistering your LIFEBOOK with Fujitsu You can register your notebook by going to our website at: us.fujitsu.com/computers. You will need to be set up with an Internet Service Provider (ISP) to register online.Fujitsu Driver Update Utility Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 121.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-74.png)
![70 - Power ManagementPower ManagementYour Fujitsu LIFEBOOK Tablet PC has many options and features for conserving battery power. Some of these features are automatic and need no user intervention. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness. Internal power management for your Tablet PC may be controlled from settings made in your operating system, pre-bundled power management application, or from settings made in BIOS setup utility.Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly. For example, you can create an appropriate power saving profile, put your Tablet PC into Sleep mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings.Power/Suspend/Resume ButtonWhen your Tablet PC is active, the Power/Suspend/Resume button can be used to manually put the Tablet PC into Sleep mode. Push the Power/Suspend/Resume button when the Tablet PC is active, but not actively accessing anything, and immediately release the button.If your Tablet PC is suspended, pushing the Power/Suspend/Resume button returns your Tablet PC to active operation. You can tell whether the system is Suspended by looking at the Power indicator. If the indicator is visible and not flashing, your Tablet PC is fully operational. If the indicator is visible andflashing, your Tablet PC is in Sleep mode. If the indicator is not visible, the power is off or your Tablet PC is in Hibernation mode.Sleep ModeSleep mode in Windows saves the contents of your system memory during periods of inactivity by maintaining power to critical parts. This mode turns off the CPU, display, hard drive, and all other internal components except those necessary to maintain system memory and for restarting. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-75.png)
![71 - Power ManagementYour Tablet PC can be put in sleep mode by:•Pressing the Power/Suspend/Resume button when your system is turned on.•Selecting “Sleep” after clicking [Start] then clicking the small arrow at the bottom right of the window.•Timing out from lack of activity.•Allowing the battery to reach the Dead Battery Warning condition.Your Tablet PC’s system memory typically stores the file on which you are working, open application information, and any other data required to support operations in progress. When you resume operation from Sleep mode, your Tablet PC will return to the point where it left off. You must use the Power/Suspend/Resume button to resume operation, and there must be an adequate power source available, or your Tablet PC will not resume.•IF RUNNING YOUR TABLET PC ON BATTERY POWER,BE AWARE THAT THE BATTERY CONTINUES TO DISCHARGEWHILE YOUR TABLET PC IS IN SLEEP MODE,THOUGH NOT AS QUICKLY AS WHEN FULLY OPERATIONAL.•DISABLING THE POWER/SUSPEND/RESUME BUTTON PREVENTS IT FROM BEING USED TO PUT THE TABLET PC INTO SLEEP OR HIBERNATION (SAVE-TO-DISK)MODE. THE BUTTON RESUME FUNCTION CANNOT BE DISABLED.•THE SLEEP OR HIBERNATION MODE SHOULD NOT BE USED WITH CERTAIN EXPRESSCARDS. CHECK YOUREXPRESSCARD DOCUMENTATION FOR MORE INFORMATION. WHEN EXPRESSCARDS OR EXTERNAL DEVICES AREIN USE, HIBERNATION MODE CANNOT RETURN TO THE EXACT STATE PRIOR TO SUSPENSION,BECAUSE ALL OFTHE PERIPHERAL DEVICES WILL BE RE-INITIALIZED WHEN THE SYSTEM RESTARTS.•IFYOUR TABLET PC IS ACTIVELY ACCESSING INFORMATION WHEN YOU ENTER THE SLEEP OR HIBERNATIONMODE,CHANGES TO OPEN FILES ARE NOT LOST. THE FILES ARE LEFT OPEN AND MEMORY IS KEPT ACTIVE DURINGSLEEP MODE OR THE MEMORY IS TRANSFERRED TO THE INTERNAL HARD DRIVE DURING HIBERNATION MODE.•THE MAIN ADVANTAGE OF USING HIBERNATION IS THAT POWER IS NOT REQUIRED TO MAINTAIN YOUR DATA. THISIS PARTICULARLY IMPORTANT IF YOU WILL BE LEAVING YOUR TABLET PC IN A SUSPENDED STATE FOR APROLONGED PERIOD OF TIME. THE DRAWBACK OF USING HIBERNATION MODE IS THAT IT LENGTHENS THE POWERDOWN AND POWER UP SEQUENCES AND RESETS PERIPHERAL DEVICES.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-76.png)
![72 - Power ManagementHibernation (Save-to-Disk) FeatureThe Hibernation feature saves the contents of your Tablet PC’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation FeatureThe default settings are not enabled. To enable or disable the Hibernation feature follow these steps:1From the Start menu, select Control Panel, then select the Power Options icon.2Select “Choose what the power button does” or “Choose what closing the lid does”, then make your selections (Do Nothing, Sleep, Hibernate, or Shut Down).Windows Power Management The Power Options icon located in the Windows Control Panel allows you to configure some of the power management settings. For example, you can use the Power Options to set the timeout values for turning off the display and hard disks whether you are running the Tablet PC on battery power or one of the adapters. Restarting the SystemIf your system is on and you need to restart it, be sure that you use the following procedure. 1Click the [Start] button, and then move the mouse over the small arrow at the bottom right of the right-hand pane.2Select Restart from the list.TURNING OFF YOUR LIFEBOOK TABLET PC WITHOUT EXITING WINDOWS OR TURNING ON YOURTABLET PC WITHIN 10 SECONDS OF THE SYSTEM BEING SHUT OFF MAY CAUSE AN ERROR WHEN YOUSTART THE NEXT TIME.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-77.png)
![73 - Power ManagementPowering OffBefore turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off the power while accessing a disk there is a risk of data loss. To ensure that your Tablet PC shuts down without error, use the Windows shut down procedure.Using the correct procedure to shut down from Windows allows your Tablet PC to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:1Click the [Start] button, and then move the mouse over the small arrow at the bottom right of the right-hand pane.2Select Shut Down from the list.If you are going to store your Tablet PC for a month or more, see Care and Maintenance Section. BE SURE TO CLOSE ALL FILES,EXIT ALL APPLICATIONS,AND SHUT DOWN YOUR OPERATING SYSTEMPRIOR TO TURNING OFF THE POWER. IF FILES ARE OPEN WHEN YOU TURN THE POWER OFF,YOU WILLLOSE ANY CHANGES THAT HAVE NOT BEEN SAVED,AND MAY CAUSE DISK ERRORS.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-78.png)
![74 Chapter 3 User-Installable FeaturesLithium ion BatteryYour LIFEBOOK Tablet PC has a Lithium ion battery that provides power for operating your Tablet PC when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.The Lithium ion battery operating time may become shorter if it is used under the following conditions:•When used at temperatures that exceed a low of 5°C or a high of 35°C (41° to 95° F). Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range.•When using a high current device such as a modem, external optical drive, or the hard drive, using the AC adapter will conserve your battery life.DO NOT LEAVE A FAULTY BATTERY IN YOUR TABLET PC. IT MAY DAMAGE YOUR AC ADAPTER,OPTIONALAUTO/AIRLINE ADAPTER,ANOTHER BATTERY OR YOUR TABLET PC ITSELF. IT MAY ALSO PREVENTOPERATION OF YOUR TABLET PC BY DRAINING ALL AVAILABLE CURRENT INTO THE BAD BATTERY.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-79.png)
![75 - Lithium ion BatteryRecharging the BatteriesIf you want to know the condition of the primary Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes.The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LIFEBOOK Tablet PC and connect the AC or Auto/Airline adapter.There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your Tablet PC is in use while the battery is charging. If you want to charge the battery more quickly, put your Tablet PC into Sleep mode, or turn it off while the adapter is charging the battery. (See Power Management on page 70 for more information on Sleep mode and shutdown procedure)•ACTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS,APPLICATIONS,FEATURES,POWERMANAGEMENT SETTINGS,BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES. OPTICAL DRIVEOR HARD DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE. THE BATTERYCHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF YOUR BATTERY IS RUNNING LOW QUICKLY,YOU SHOULD REPLACE IT WITH A NEW ONE.•UNDER FEDERAL,STATE,OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTINGTHEM IN THE TRASH. PLEASE TAKE CARE OF OUR ENVIRONMENT AND DISPOSE OF BATTERIESPROPERLY. CHECK WITH YOUR LOCAL GOVERNMENT AUTHORITY FOR DETAILS REGARDING RECYCLINGOR DISPOSING OF OLD BATTERIES. IF YOU CANNOT FIND THIS INFORMATION ELSEWHERE,CONTACTYOUR SUPPORT REPRESENTATIVE AT 1-800-8FUJITSU (1-800-838-5487)MAKE SURE THAT THE PERCENTAGE CHARGE IS INDICATED BY THE BATTERY CHARGING INDICATOR ONTHE STATUS INDICATOR PANEL.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-80.png)
![76 - Lithium ion BatteryLow Battery StateWhen the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your Tablet PC will go into Sleep mode. There is no guarantee that your data will be saved once the Tablet PC reaches this point.Dead Battery Suspend mode shows on the Status indicator just like the normal Sleep mode. Once your Tablet PC goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Power/Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your Tablet PC while an adapter is charging the battery.USING HEAVY CURRENT DEVICES OR FREQUENT EXTERNAL OPTICAL DRIVE ACCESSES MAY PREVENTCHARGING COMPLETELY.•ONCE THE LOW BATTERY NOTIFICATION MESSAGE APPEARS,YOU NEED TO SAVE ALL YOUR ACTIVE DATA ANDPUT YOUR LIFEBOOK TABLET PC INTO SLEEP MODE UNTIL YOU CAN PROVIDE A NEW POWER SOURCE. YOUSHOULD PROVIDE A CHARGED BATTERY,AN AC POWER ADAPTER,OR AUTO/AIRLINE ADAPTER AS SOON ASPOSSIBLE.• WHEN YOU ARE IN SLEEP MODE THERE MUST ALWAYS BE AT LEAST ONE POWER SOURCE ACTIVE. IF YOUREMOVE ALL POWER SOURCES WHILE YOUR LIFEBOOK TABLET PC IS IN SLEEP MODE,ANY DATA THAT HASNOT BEEN SAVED TO THE HARD DRIVE WILL BE LOST.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-81.png)
![77 - Lithium ion BatteryShorted BatteriesThe Status Indicator panel indicator associated with the Battery Level indicator displays the operating level available in that battery. If this display shows a flashing red LED, it means the battery is damaged and must be replaced so it does not damage other parts of your LIFEBOOK Tablet PC.Replacing the Battery With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. There are two ways to swap batteries, cold-swapping and hot-swapping:Cold-swapping BatteriesTo cold-swap batteries in your battery bay, follow these easy steps (Figure 34):1Have a charged battery ready to install.2Shut down your Tablet PC and disconnect the AC adapter. 3Turn the system upside down.4While pushing the battery bay release latches towards the back of the battery, lift the battery out of the bay.5Insert a new battery into the bay, and press it in firmly so that the latches click into place. 6Plug in the AC adapter and turn the power on. Hot-swapping BatteriesTo hot-swap batteries in your battery bay follow these easy steps: 1Plug an AC Adapter into the system and connect it to a power outlet.BE SURE TO PLUG IN AN AC ADAPTER PRIOR TO REMOVING THE BATTERY. THERE IS NO BRIDGEBATTERY PRESENT TO SUPPORT THE SYSTEM WHILE THE BATTERY IS BEING REPLACED. IF YOU DO NOTUSE AN AC ADAPTER YOU WILL LOSE ANY UNSAVED FILES.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-82.png)
![78 - Lithium ion BatteryFigure 34. Removing a Battery2Follow steps 3 through 6 in “Cold Swapping Batteries”.Battery Bay Release LatchesBattery PackIFTHE LITHIUM ION BATTERY CONNECTOR IS NOT FULLY SEATED,YOU MAY NOT BE ABLE TO USE YOURTABLET PC OR CHARGE YOUR BATTERY.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-83.png)
![79 - Memory Stick/Secure Digital CardsFigure 35. Installing a Memory Stick or SD CardMemory Stick/Secure Digital CardsYour LIFEBOOK Tablet PC supports Memory Sticks and Secure Digital (SD) cards, on which you can store and transfer data to and from a variety of digital devices. These cards use flash memory architecture, which means they don’t need a power source to retain data. Memory Stick is a flash memory technology that allows you to record, transfer and share digital content, such as digital pictures, movies, music, voice, and computer data and applications.Secure Digital (SD) Cards are very similar to Memory Sticks. Like Memory Sticks, SD Cards allow portable storage among a variety of devices, such as cell phones, GPS systems, digital cameras, and PDAs. SD Cards transfer data quickly, with low battery consumption. Like the memory stick, it uses flash memory architecture.Memory StickSD CardDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-84.png)
![80 - Memory Stick/Secure Digital CardsInstalling Memory Stick/SD CardsMemory Stick and SD Cards are installed in the Memory Stick/SD Card slot. To install a Memory Stick or SD Card, follow these steps:1See your specific card manual for instructions on the installation of your card. Some cards may require that your Tablet PC is off while installing them.2Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD Card.3Insert your card into the slot with the product label facing up.4Push the card firmly into the slot until it is seated in the connector. Removing A Memory Stick/SD CardTo remove a Memory Stick or SD Card, follow these easy steps:1Select Safely Remove Hardware from the System Tray. Highlight the card in the list, then click [Stop].2Push the Memory Stick or SD Card in until it unlatches. It will then eject from the slot for removal.INSTALLING OR REMOVING A MEMORY STICK OR SD CARD DURING YOUR LIFEBOOK TABLET PC’SSHUTDOWN OR BOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK TABLET PC.DO NOT INSERT A CARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ON THE CARD ASYOU MAY PERMANENTLY DAMAGE THE CARD,YOUR LIFEBOOK TABLET PC, OR BOTH.SEE YOUR CARD MANUAL FOR SPECIFIC INSTRUCTIONS ON THE REMOVAL OF YOUR CARD. SOMECARDS MAY REQUIRE YOUR LIFEBOOK TABLET PC TO BE IN SLEEP MODE OR OFF WHILE REMOVINGTHEM.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-85.png)
![81 - ExpressCardsFigure 36. Installing/Removing ExpressCardExpressCardsYour LIFEBOOK Tablet PC supports ExpressCards which can perform a variety of functions depending on which type of card you install. There are two different width ExpressCards: 34 mm and 54 mm. The connector inside the slot is located on the left-hand side of the slot. If you insert a 34 mm card, be sure to align it with the left side of the slot when inserting it.For further information, refer to the instructions supplied with your card(s).Installing ExpressCardsTo install an ExpressCard in the ExpressCard slot, follow these steps: Eject ButtonExpressCard Slot54 mm ExpressCard34 mm ExpressCard•INSTALLING OR REMOVING A EXPRESSCARD DURING YOUR LIFEBOOK TABLET PC’S SHUTDOWN ORBOOTUP PROCESS MAY DAMAGE THE CARD AND/OR YOUR LIFEBOOK TABLET PC.•DO NOT INSERT AN EXPRESSCARD INTO A SLOT IF THERE IS WATER OR ANY OTHER SUBSTANCE ONTHE CARD AS YOU MAY PERMANENTLY DAMAGE THE CARD,YOUR LIFEBOOK TABLET PC, OR BOTH.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-86.png)
![82 - ExpressCards1See your ExpressCard manual for instructions on the installation of your card. Some cards may require that your Tablet PC is off while installing them.2Make sure there is no ExpressCard currently in the slot. If there is, see Removing ExpressCards.3If the eject button is extended, press it until it clicks. 4Insert the card into the slot with the label facing up.5Push the card firmly into the slot until it is seated in the connector. Removing ExpressCardsSee your ExpressCard manual for specific instructions on removing your card. Some cards may require your Tablet PC to be in Sleep Mode or Off during removal.1Unlock the card from the slot by pressing the eject button associated with the slot in which the card is located. When pressed, the button will pop out. 2Firmly press the button again until it is flush with the Tablet PC. This will eject the card slightly out of the slot allowing you to remove the card.YOU MAY BE REQUIRED TO LOG ON AS AN ADMINISTRATOR OR MEMBER OF THE ADMINISTRATOR’SGROUP TO COMPLETE THIS PROCEDURE. IF THE COMPUTER IS CONNECTED TO A NETWORK,NETWORKPOLICY SETTINGS MAY ALSO PREVENT YOU FROM COMPLETING THIS PROCEDURE.•WINDOWS HAS A SHUTDOWN PROCEDURE FOR EXPRESSCARDS THAT MUST BE FOLLOWED BEFOREREMOVING A CARD. (REVIEW YOUR OPERATING SYSTEM MANUAL FOR THE CORRECT PROCEDURE.) ITIS GOOD PRACTICE TO REMOVE DEVICES USING SAFELY REMOVE HARDWARE IN THE SYSTEM TRAY.•IF THE DIALOG BOX STATES THAT THE DEVICE CANNOT BE REMOVED,YOU MUST SAVE ALL OF YOUROPEN FILES,CLOSE ANY OPEN APPLICATIONS AND SHUT DOWN YOUR TABLET PC.IFTHE EXPRESSCARD HAS AN EXTERNAL CONNECTOR AND CABLE,DO NOT PULL THE CABLE WHENREMOVING THE CARD.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-87.png)
![83 - ExpressCardsSmart Card ReaderA dedicated Smart Card Reader is provided on your Tablet PC. Smart Cards are the same size and shape as credit cards, but they contain embedded integrated circuits. The chip can hold a variety of information, and provides you with many possible options, such as allowing you to make secure purchases, pay for phone calls, store security information, and provide personal identification and information. In order to use the Smart Card Reader, you must purchase optional Smart Card third-party software.Figure 37. Smart Card SlotSmart Card SlotDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-88.png)
![84 - Memory Upgrade ModuleMemory Upgrade ModuleYour Fujitsu LIFEBOOK Tablet PC comes with a minimum of 1GB of high speed Double Data Rate Synchronous Dynamic RAM (DDR3-1333 SDRAM) factory installed. To increase your Tablet PC’s memory capacity, you may install an additional memory upgrade module. The memory upgrade must be a dual-in-line (DIMM) SDRAM module. To ensure 100% compatibility, purchase the SDRAM module only from the Fujitsu web store at www.shopfujitsu.com.Installing Memory Upgrade Modules1Turn off power to your Tablet PC, remove any power adapter (AC or auto/airline). Remove the battery. 2Make sure that all the connector covers are closed.3Turn the Tablet PC bottom side up, and remove the screws from the memory upgrade module compartment. 4Slide the cover towards the battery compartment slightly, then lift it and remove it (Figure 38).5Remove the memory upgrade module from the static guarded sleeve.6Align the memory upgrade module with the part side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment.(Figure 38)•DO NOT REMOVE ANY SCREWS FROM THE MEMORY UPGRADE MODULE COMPARTMENT EXCEPT THEONES SPECIFICALLY SHOWN IN THE DIRECTIONS FOR INSTALLING AND REMOVING THE MEMORYUPGRADE MODULE.•THE MEMORY UPGRADE MODULE CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE(ESD). TO MINIMIZE RISK TO THE MODULE,OBSERVE THE FOLLOWING PRECAUTIONS:•BEFORE HANDLING A MEMORY MODULE,TOUCH A GROUNDED METAL OBJECT TO DISCHARGESTATIC ELECTRICITY BUILT UP IN YOUR BODY.•WHEN INSTALLING OR REMOVING A MEMORY MODULE,HOLD IT BY THE EDGE SO AS NOT TOTOUCH ANY CONTACTS OR CHIPS. BE CAREFUL NOT TO TOUCH ANY INTERNAL COMPUTERTERMINALS OR COMPONENTS;THE OIL FROM YOUR FINGERS COULD CAUSE A SHORT TO THECOMPONENTS.•BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING MEMORY MODULES.EVEN IF THE SYSTEM IS IN HIBERNATE OR SLEEP STATES,DATA COULD BE LOST OR THE MEMORYCOULD BE DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-89.png)
![85 - Memory Upgrade ModuleFigure 38. Opening Memory Compartment7Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You’ll hear a click when it is properly in place.8Replace the cover and reinstall the screws.THE MEMORY UPGRADE MODULE IS NOT SOMETHING YOUROUTINELY REMOVE FROM YOUR TABLET PC. ONCE IT ISINSTALLED,YOU CAN LEAVE IT IN PLACE UNLESS YOU WANTTO CHANGE SYSTEM MEMORY CAPACITY.Figure 39. Installing a Memory ModuleDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-90.png)
![86 - Memory Upgrade ModuleChecking the Memory CapacityOnce you have changed the system memory capacity by replacing the installed module with a larger one, be sure to check that your Tablet PC has recognized the change.•If you are in Control Panel Category view, check the memory capacity by clicking [Start] -> Control Panel -> System and Security -> System. The amount of memory is displayed next to “Installed Memory - RAM:” •If you are in one of the icon views, check the memory capacity by clicking [Start] -> Control Panel -> System. The amount of memory is displayed next to “Memory - RAM:”Removing a Memory Upgrade Module1Perform steps 1 through 4 of Installing a Memory Upgrade Module.2Pull the clips sideways away from each side of the memory upgrade module at the same time. 3While holding the clips out, remove the module by lifting it up and pulling it away from your Tablet PC. 4Store the memory upgrade module in a static guarded sleeve.5Replace the cover and reinstall the screws.Figure 40. Removing a Memory ModuleDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-91.png)
![87 - Memory Upgrade ModuleThere may be a variation between the actual memory size and what is displayed. This is possible if your system is configured with an integrated Intel Graphics Media Accelerator which dynamically allocates system memory to accelerate graphics performance.IF THE TOTAL MEMORY DISPLAYED IS INCORRECT,CHECK THAT YOUR MEMORY UPGRADE MODULE ISPROPERLY INSTALLED. (IF THE MODULE IS PROPERLY INSTALLED AND THE CAPACITY IS STILL NOTCORRECTLY RECOGNIZED,SEE TROUBLESHOOTING ON PAGE 98.DRAFTibl ifibl if](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-92.png)
![88 - Device PortsDevice PortsYour Fujitsu LIFEBOOK Tablet PC and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, printers, etc. Internal LAN (RJ-45) JackThe internal LAN (RJ-45) jack is used for a Gigabit (10Base-T/100Base-Tx/1000Base-T) Ethernet LAN connection. You may need to configure your Tablet PC to work with your particular network. (Please refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these easy steps: Port Replicator ConnectorThe port replicator connector is used for the connection of your Tablet PC to an optional port replicator. In order to connect your Tablet PC to this device, refer to “Port Replicator” on page 93.1Align the connector with the port opening.2Push the connector into the port until it is seated.3Plug the other end of the cable into a LAN outlet.Figure 41. Connecting the LANDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-93.png)
![89 - Device PortsUniversal Serial Bus PortsThe Universal Serial Bus ports (USB) allow you to connect USB devices such as external game pads, pointing devices, keyboards and/or speakers. There are three USB ports on your Tablet PC; on the left-hand side is a USB 3.0 port, and on the rear are two USB 2.0 ports, one of which is an Anytime USB Charge port..In order to connect a USB device follow these steps:1Align the connector with the port opening.2Push the connector into the port until it is seated.Figure 42. Connecting a USB DeviceUSB 2.0 Port withAnytime USB ChargeDUE TO THE ONGOING CHANGES IN USB TECHNOLOGY AND STANDARDS,NOT ALL USB DEVICESAND/OR DRIVERS ARE GUARANTEED TO WORK.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-94.png)
![90 - Device PortsIEEE 1394 PortThe 4-pin 1394 port allows you to connect digital devices that are compliant with IEEE 1394 standard. The IEEE 1394 standard is easy to use, connect, and disconnect. This port can allow up to 400 Mbps transfer rate. A third-party application may be required to operate your device with the 1394 port.THE 1394 PORT USED IN THIS SYSTEM USES A FOUR-PIN CONFIGURATION. IF YOU INTEND TOINTERFACE WITH DEVICES WHICH USE A SIX-PIN CONFIGURATION,YOU WILL NEED TO PURCHASE ANADAPTER.In order to connect a 1394 device, follow these steps:1Align the connector with the port opening.2Push the connector into the port until it is seated.Figure 43. Connecting an IEEE1394 DeviceDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-95.png)
![91 - Device PortsHeadphone JackThe headphone jack allows you to connect headphones or powered external speakers to your Tablet PC. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.Microphone JackThe microphone jack allows you to connect an external microphone. Your microphone must be equipped with a 1/8”(3.5 mm) mono mini-plug in order to fit into the microphone jack of your Tablet PC. In order to connect a microphone follow these easy steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.External Video PortThe external video port allows you to connect an external monitor or LCD projector. In order to connect an external video device, follow these easy steps: 1Align the connector with the port opening.2Push the connector into the port until it is seated.3Tighten the two hold-down screws, located on each end of the connector.PRESSING THE [FN] + [F10] KEYS ALLOWS YOU TO CHANGE YOUR SELECTION OF WHERE TO SENDYOUR DISPLAY VIDEO. EACH TIME YOU PRESS THE KEY COMBINATION,YOU WILL STEP TO THE NEXTCHOICE,STARTING WITH THE BUILT-IN DISPLAY PANEL ONLY,MOVING TO THE EXTERNAL MONITORONLY,FINALLY MOVING TO BOTH THE BUILT-IN DISPLAY PANEL AND AN EXTERNAL MONITOR.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-96.png)
![92 - Device PortsFigure 44. Connecting an External Video DeviceDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-97.png)
![93 - Port ReplicatorPort ReplicatorThe port replicator extends the functionality of your LIFEBOOK® Tablet PC by providing ports to connect an external VGA monitor, a LAN (RJ-45) cable, four USB 2.0 devices, a DVI device, a DisplayPort device, headphones, and DC power. The port replicator connects to the bottom of your LIFEBOOK Tablet PC.Figure 45. Port Replicator - RearDocking ConnectorDC PowerJackSecurity Lock SlotHeadphone JackLAN (RJ-45)PowerButtonDVI-D PortUSB 2.0 Ports (Qty. 4)DisplayPortExternal VGA PortDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-98.png)
![94 - Port ReplicatorPort Replicator ComponentsThe following is a brief description of the port replicator’s back panel components. (Figure 45)Power ButtonThe power button allows you to power the port replicator on and off.Docking ConnectorThe docking connector allows you to connect the Port Replicator to your LIFEBOOK Tablet PC.DVI-D PortThe DVI-D port lets you to connect digital display devices such flat panel displays and digital projectors using a DVI-D cable. DVI-D is primarily used to connect a computer with a home theater system.DisplayPortThe DisplayPort lets you to connect DisplayPort-compatible digital display devices such flat panel displays and digital projectors using a DisplayPort cable.THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE(ESD). TO MINIMIZE RISK TO THE COMPONENTS,OBSERVE THE FOLLOWING PRECAUTIONS:•BEFORE DOCKING OR UNDOCKING YOUR LIFEBOOK WHEN USING A PORT REPLICATOR,YOU SHOULD TOUCH AGROUNDED METAL OBJECT TO DISCHARGE STATIC ELECTRICITY BUILT UP IN YOUR BODY.•BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING SYSTEM COMPONENTS. EVEN IF THESYSTEM IS IN HIBERNATE OR SLEEP STATES,DATA COULD BE LOST OR MEMORY COULD BE DAMAGED IF POWER ISSTILL AVAILABLE TO THE SYSTEM.•ALTHOUGH DISPLAYPORT AND DVI-D DEVICES ARE SUPPORTED BY THE PORT REPLICATOR,ONLY ONE CAN BEUSED AT ANY TIME. AN INTERNAL SWITCH RECOGNIZES WHICH TYPE OF DEVICE IS CONNECTED. IF BOTH ARECONNECTED AT THE SAME TIME, DISPLAYPORT HAS THE HIGHER PRIORITY.•A DISPLAYPORT OR DVI-D DEVICE CAN BE USED CONCURRENTLY WITH AN EXTERNAL VIDEO DEVICE THAT ISCONNECTED TO THE ANALOG EXTERNAL VGA PORT.•HOT PLUG IS NOT SUPPORTED BY THE DISPLAYPORT OR DVI-D PORTS.•IFA DISPLAYPORT-TO-HDMI CONVERTER IS CONNECTED TO THE DISPLAYPORT,SOUND WILL NOT BE OUTPUTFROM THE HDMI DEVICE. TOUSEAN HDMI DEVICE,PLUG IT INTO THE HDMI PORT ON THE SYSTEM’S LEFT SIDE.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-99.png)
![95 - Port ReplicatorUSB 2.0 Ports (Qty. 4)Universal Serial Bus (USB) 2.0 ports allow you to connect USB devices. USB 2.0 ports are backward-compatible with USB 1.1 devices.External VGA PortThe external VGA port lets you connect an external monitor or projector. Note that if a Port Replicator is attached, you must use the external VGA port on the Port Replicator, not the one on your system. Headphone JackThe headphone jack allows you to listen to stereo sound from your Tablet PC with portable headphones.LAN (RJ-45) Jack The LAN jack allows you to connect a LAN to the Port Replicator. Note that when the system is attached to the Port Replicator, the LAN Jack on the Port Replicator should be used, not the one on the system.Security Lock SlotThe security lock slot allows you to attach an optional physical lock down device.DC Power JackThe DC power jack allows you to plug in the AC adapter to power your Tablet PC and charge the internal Lithium ion battery.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-100.png)
![96 - Attaching the Port ReplicatorDetaching Port ReplicatorTo detach the Port Replicator:1Pull the Port Replicator’s release latch away from the Port Replicator to release it from your Tablet PC. (Figure 47)2Lift the Tablet PC away from the Port Replicator to detach it. (Figure 48)Attaching the Port ReplicatorTo attach the Port Replicator, align the Port Replicator connector on the bottom of your Tablet PC with the connector on the Port Replicator and push the corners down simultaneously. (Figure 46)Figure 46. Attaching the Port ReplicatorDocking ConnectorDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-101.png)
![97 - Figure 47. Unlatching the Port Replicator Figure 48. Removing the SystemRelease LatchDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-102.png)
![98 Chapter 4 Troubleshooting Your LIFEBOOKTroubleshootingThere may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.Identifying the ProblemIf you encounter a problem, go through the following procedure before pursuing complex troubleshooting:1Turn off your LIFEBOOK Tablet PC.2Make sure the AC adapter is plugged into your Tablet PC and to an active AC power source.3Make sure that any card installed in the ExpressCard slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.4Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.5Turn on your Tablet PC. Make sure it has been off at least 10 seconds before you turn it back on.6Go through the boot sequence.7If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information.](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-103.png)
![99 - Troubleshooting8If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) E-mail: 8fujitsu@us.fujitsu.com Web site: http://www.computers.us.fujitsu.com/support.Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:•Product name•Product configuration number•Product serial number•Purchase date•Conditions under which the problem occurred•Any error messages that have occurred•Type of device connected, if anySee the Configuration Label on the bottom of your Tablet PC for configuration and serial numbers. IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED,YOUR SUPPORT REPRESENTATIVE MAY BEABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-104.png)
![100 - TroubleshootingSpecific ProblemsUsing the Troubleshooting TableWhen you have problems with your LIFEBOOK Tablet PC, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your Tablet PC.Troubleshooting TableProblemPageAudio Problems . . . . . . . . . . . . . page 101Optical Drive Problems . . . . . . . page 101Port Replicator Problems . . . . . . page 102Hard Drive Problems . . . . . . . . . page 102Keyboard or Mouse Problems . . page 103Memory Problems . . . . . . . . . . . page 103ProblemPageUSB Device Problems. . . . . . . . . page 103ExpressCard Problems . . . . . . . . page 104Power Failures . . . . . . . . . . . . . . page 104Shutdown and Startup Problems. page 106Video Problems . . . . . . . . . . . . . . page 107Miscellaneous Problems . . . . . . . page 109](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-105.png)
![101 - TroubleshootingProblem Possible Cause Possible SolutionsAudio ProblemsThere is no sound coming from the built-in speaker.The volume is turned too low. Adjust the volume control on your Tablet PC and operating system. Use the [Fn+F9] key combination on your keyboard. Pressing [F9] repeatedly while holding [Fn] will increase the volume of your Tablet PC.The software volume control is set too low.Manually adjusting the volume (i.e., keyboard "hot keys") should dynamically adjust the volume of the operating sys-tem (see above). If that doesn’t work, adjust the sound vol-ume control settings in your software or application.Headphones are plugged into your Tablet PC.Plugging in headphones disables the built-in speakers. Remove the headphones.Software driver is not configured correctly.The audio driver may be installed or reinstalled using the Drivers and Applications CD that came with your Fujitsu LIFEBOOK. Refer to your application and operating system documentation for help.The speakers have been muted using the Volume icon in the system tray.Click the Volume icon in the system tray on the bottom right of the screen. (It looks like a speaker). If the Mute box has a red circle on it, click on it to unselect it. You can also use the [Fn+F3] key combination to toggle the volume on and off. Pressing [F3] while holding [Fn] will toggle the audio mute.Optical Drive Problems LIFEBOOK Tablet PC fails to recognize DVD/CD-RW/CD-ROM’s.The disc is not pushed down onto raised center circle of the drive.Open optical drive tray and re-install the disc properly.Optical drive tray is not latched shut.Push on the front of the optical drive tray until it latches. If that doesn’t work, pull out the modular drive latch to remove the device from the bay, then re-insert the drive until it latched; this ensures that the drive is properly seated. Incorrect DVD Player or player software is installed.Install DVD Player software. (See “Media Player Software” on page 73 for more information.)DRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-106.png)
![102 - TroubleshootingLIFEBOOK Tablet PC fails to recognize DVD/CD-RW/CD-ROM’s.(continued)Wrong drive designator was used for the disc in the appli-cation.Verify the drive designator used by the application is the same as the one used by the operating system. When the operating system is booted from a DVD/CD, drive designa-tions are automatically adjusted. Note that the drive designa-tion can be changed with the Disk Management tool located at Control Panel -> Administrative Tools -> Computer Man-agement.DVD/CD-RW/CD-ROM is dirty or defective.Wipe the disc with a non-abrasive CD cleaning cloth and reinsert. If it still will not work try another DVD/CD-RW/CD-ROM in the drive.Drive access indicator on the Status Indicator Panel blinks at regular intervals with no disc in the tray or the drive is not installed.The Windows auto insertion function is active and is checking to see if a disc is ready to run. This is normal. However, you may disable this feature. Port Replicator ProblemsNote: Be sure to power down your LIFEBOOK Tablet PC before adding a printer to the Port Replicator parallel port.Tablet PC does not turn on when installed in the optional Port ReplicatorPort Replicator AC adapter is not plugged in.Provide power to the Port Replicator.Tablet PC is not properly seated in the Port Replicator.Remove and re-dock your LIFEBOOK Tablet PC.Hard Drive ProblemsYou cannot access your hard drive.The wrong drive designator was used by an application when a bootable disc was used to start the Tablet PC.Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted. Security is set so your operat-ing system cannot be started without a password.Verify your password and security settings.Problem Possible Cause Possible SolutionsDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-107.png)
![103 - TroubleshootingKeyboard or Mouse ProblemsThe built-in keyboard does not seem to work.The Tablet PC has gone into Sleep mode.Push the Power/Suspend/Resume button.Your application has locked out your keyboard.Try to use your integrated pointing device to restart your sys-tem.You have installed an external keyboard or mouse, and it does not seem to work.Your external device is not properly installed.Re-install your device. See “Device Ports” on page 88.Your operating system is not set up with correct software driver for that device.Check your device and operating system documentation and activate the proper driver.You have connected an external keyboard or a mouse and it seems to be locking up the system.Your OS is not setup with cor-rect driver for that device.Check your device and operating system documentation and activate the proper driver.Your system has crashed. Try to restart your Tablet PC. Memory ProblemsYour System screen in the Control Panel does not show the correct amount of installed memory.Your memory upgrade mod-ule is not properly installed.Remove and re-install your memory upgrade module. See“Memory Upgrade Module” on page 84.You have a memoryfailure.Check for Power On Self Test (POST) messages. See “Power On Self Test Messages” on page 110. USB Device ProblemsYour LIFEBOOK doesn’t recognize an installed USB deviceit, or it doesn’t work.The device is not properly installed.Remove and re-install the device. See “Device Ports” on page 88.Your device may not have the correct software driver active.See your software documentation and activate the correct driver.The device may have been installed while an application was running, so your system is not aware of its installation.Close the application and restart your Tablet PC.Problem Possible Cause Possible SolutionsDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-108.png)
![104 - TroubleshootingExpressCard ProblemsA card inserted in the ExpressCard slot does not work or is locking up the system.Card is not properly installed. Remove and re-install the card. See “ExpressCards” on page 81.Card may have been installed while an application was run-ning, so your Tablet PC is not aware of its installation.Close the application and restart your Tablet PC.Your software may not have the correct driver active.See your software documentation and activate the correct driver.Power FailuresYou turn on your LIFE-BOOK Tablet PC and nothing seems to happen.The installed battery is com-pletely discharged or there is no power adapter installed.Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 26. Install a charged battery or a Power adapter.The battery is installed but is faulty.Use the Status Indicator panel to verify the presence and condition of the battery. See “Status Indicator Panel” on page 26. If the battery indicates a short, remove it and operate from another power source or replace that battery.The battery is low. Check the Status Indicator Panel to determine the presence and condition of the battery. See “Status Indicator Panel” on page 26. Use a Power adapter to operate until a battery is charged or install a charged battery.The power adapter is not plugged in properly.Verify that your adapter is connected correctly. See “Power Sources” on page 62.The power adapter (AC or auto/airline) has no power from the AC outlet, airplane jack, or car cigarette lighter.Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.The power adapter (AC or auto/airline) is faulty.Try a different power adapter.Problem Possible Cause Possible SolutionsDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-109.png)
![105 - TroubleshootingYour LIFEBOOK Tablet PC turns off all by itself.The power management parameters are set for auto timeouts which are too short for your operating needs.Press any button on the keyboard, or move the mouse. If that fails, push the Power/Suspend/Resume button. Check your power management settings, or close your applications and go to the Power Options located in the Control Panel to adjust the timeout values to better suit your needs.You are operating on battery power and ignored a low bat-tery alarm until the battery was at the dead battery state and the system has entered Dead Battery Suspend mode.Install a power adapter, then push the Power/Sus-pend/Resume button. See “Power Sources” on page 62.You have a battery failure. Verify the condition of the battery using the Status Indicator panel. If the battery is shorted, replace or remove it. See“Status Indicator Panel” on page 26.Your power adapter has failed or lost its power source.Make sure the adapter is plugged in and the outlet has power.Your LIFEBOOK Tablet PC will not work on battery alone.The installed battery is dead. Replace the battery with a charged one or install a power adapter.Battery is improperly installed. Verify that the battery is properly connected by re-installing it.Your installed battery is faulty. Verify the condition of the battery using the Status Indicator panel and replace or remove any batteries that are shorted. See “Status Indicator Panel” on page 26.The battery seems to discharge too quickly.The power savings features may be disabled.Check the Power Options menu settings and adjust accord-ing to your operating needs.The brightness is turned all the way up.Turn down the brightness adjustment. The higher the bright-ness the more power your display uses.The battery is very old. Replace the battery.Problem Possible Cause Possible SolutionsFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-110.png)
![106 - TroubleshootingThe battery seems to discharge too quickly.(continued)You are running an applica-tion that uses a lot of power due to frequent hard drive access or optical drive access, or use of a Wireless LAN, or Bluetooth device.Use a power adapter for this application when at all possible.The battery has been ex-posed to high temperatures.Replace the battery.The battery is too hot or too cold.Restore the Tablet PC to normal operating temperature. Charging icon on the Status Indicator panel will flash when battery is outside of operating range.Shutdown and Startup ProblemsThe Suspend/Resume button does not work.Suspend/Resume button is disabled. To enable the button, go to the Control Panel -> Power Options Properties and click the Advanced tab. In the Power buttons area, select “Change what the power button does” .There may be application software. conflictClose all applications and try the button again.The system powers up, and displays power on information, but fails to load the operating system.The boot sequence settings of the setup utility are not compatible with your configu-ration.Set the operating source by pressing the [ESC] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. See “BIOS Setup Utility” on page 66.You have a secured system requiring a password to load your operating system.Make sure you have the right password. Enter the setup util-ity and verify the Security settings and modify them as accordingly. See “BIOS Setup Utility” on page 66.Internal hard drive was not detected.Use the BIOS setup utility or Primary Master submenu, located within the Main menu, to try to auto detect the inter-nal hard drive.Problem Possible Cause Possible SolutionsDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-111.png)
![107 - TroubleshootingAn error message is dis-played on the screen dur-ing the Boot sequence.Power On Self Test (POST) has detected a problem.See the POST messages to determine the meaning and severity of the problem. Not all messages are errors; some are simply status indicators. See “Power On Self Test Mes-sages” on page 110.Your Tablet PC appears to change setup parameters when you start it.BIOS setup changes were not saved when made and you exited the setup utility.Make sure you select Save Changes And Exit when exiting the BIOS setup utility.The BIOS CMOS hold-up bat-tery has failed.Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years.Your system display won’t turn on when the system is turned on or has resumed.You have installed the LIFE-BOOK/Security Application panel.Check the Status Indicator Panel for presence of the Security icon. If it is visible, enter your password See “Status Indicator Panel” on page 26.Video ProblemsThe built-in display is blank when you turn on your LIFEBOOK Tablet PC.The Tablet PC is set for an external monitor only.Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the keys you will step to the next choice. The choices, in order are: built-in display only, external moni-tor only, both built-in display and external monitor.Display angle and brightness settings are not adequate for your lighting conditions.Move the display and the brightness control until you have adequate visibility. Pressing either the [F6] or [F7] keys while holding down the [Fn] key also allows you to change the brightness level of the display.Power management time-outs are set for short intervals and you didn’t see the display go on and off again.Press a keyboard button or move the mouse to restore oper-ation. If that fails, push the Power/Suspend/Resume button. (The display may be shut off by Sleep mode, Auto Suspend or Video Timeout)The Tablet PC turned on with a series of beeps and the built-in display is blank.Power On Self Test has detected a failurethat doesn’t allow the display to operate.Contact your support representative.Problem Possible Cause Possible SolutionsDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-112.png)
![108 - TroubleshootingThe display goes blank by itself after you have been using it.The Tablet PC has gone into Video timeout, Sleep mode, or Save-to-Disk mode because you have not used it for a period of time.Press any keyboard button, or move the mouse to restore operation. If that fails, push the Power/Suspend/Resume but-ton. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your opera-tion needs. See “BIOS Setup Utility” on page 66.The power management time-outs may be set for very short intervals and you failed to notice the display come on and go off again.Press any button on the keyboard, or move the mouse to restore operation. If that fails, push the Power/Sus-pend/Resume button. (The display may be shut off by Sleep Mode, Auto Suspend or Video Timeout)Your display won’t turn on when the system is turned on or when it has resumed.The system may be pass-word-protected.Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.The display does not close.A foreign object, such as a paper clip, is stuck between the display and keyboard.Remove all foreign objects from the keyboard.The display has bright or dark spots.If the spots are very tiny and few in number, this is normal for a large LCD display.This is normal; do nothing.If the spots are numerous or large enough to interfere with your operation needs.Display is faulty; contact your support representative.The display is dark when on battery power.The Power Management util-ity default is set on low bright-ness to conserve power.Press [Fn] + [F7] to increase brightness or click the battery gauge, click on More power options, and select Adjust the display brightness.You have connected an external monitor but it does not display anything.Your operating system is not setup with the correct soft-ware driver for that device. Check your device and operating system documentation and activate the proper driver.Problem Possible Cause Possible SolutionsDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-113.png)
![109 - TroubleshootingYou have connected an external monitor but it does not display anything.(continued)Your BIOS setup is not set to enable your external monitor.Toggle the video destination by pressing [Fn]+ [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located in the Advanced Menu of the BIOS. See “BIOS Setup Utility” on page 66.Your external monitor is not properly installed. Reinstall your device. See “External Video Port” on page 91.You have connected an external monitor and it does not come on.Your external monitor is not compatible with your LIFE-BOOK Tablet PC.See your monitor documentation and the External Monitor Support portions of the Specifications section. See “Specifi-cations” on page 130.Miscellaneous ProblemsError message is dis-played on the screen dur-ing the operation of an application.Application software often has its own set of error message displays.See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.Problem Possible Cause Possible SolutionsFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-114.png)
![110 - TroubleshootingPower On Self Test MessagesThe following is a list of error-and-status messages that the Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check the operating system documentation on screen and in the manual. If you can find no reference to the message, contact a support representative.*Invalid NVRAM DataProblem with NVRAM access. In the unlikely case that you see this message you may have a display problem. You can continue operating but should contact your support representative for more information.*Keyboard controller error The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.*Keyboard not detectedKeyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.*Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted.*Press <F1> to resume, <F2> to SETUP Displayed after any recoverable error message. Press [F1] key to Continue or [F2] key to Enter Setup.*Real time clock error - Check date and time settingsReal-time clock fails BIOS test. May require board repair. Contact your support representative.*Fan error, system shutdown in 30s. Contact Fujitsu tech supportFan error occurred. Please contact your sales representative.*Fan error occurred during previous boot.Fan error occurred during previous boot. Please contact your sales representative.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-115.png)
![111 - Restoring Your Pre-installed SoftwareRestoring Your Pre-installed SoftwareIt is very important that you create DVD copies of your Factory Image before beginning to use your system. To do so, follow the instructions below in the “Saving Your Factory Image” section. Along with instructions on saving your Factory Image, this document outlines several other important procedures, such as making a system image, restoring your Factory Image and system images, managing your images, and restoring the partitions on a hard drive.Saving your Factory ImageWhen you purchased your system, a copy of the pre-installed Factory Image was loaded into a hidden partition on your hard disk drive. Having a copy of the original Factory Image available to you means that in the event of system failure, you will be able to restore it to its original state.•IN ORDER TO INSTALL APPLICATIONS AND DRIVERS,MAKE COPIES OF FACTORY AND SYSTEM IMAGES,AND BURNDRIVERS AND APPLICATION RESTORE DISCS,APPLICATION MEDIA,AND BOOTABLE DISCS YOU MUST HAVE ANINTERNAL OR EXTERNALLY CONNECTED WRITABLE DVD DRIVE.•IT IS EXTREMELY IMPORTANT THAT YOU COPY YOUR FACTORY IMAGE TO REMOVABLE MEDIA (E.G., DVD DISCS).FAILURE TO DO SO COULD RESULT IN AN INABILITY TO RESTORE THE IMAGE AT A FUTURE DATE.•WE RECOMMEND THAT YOU USE DVD-R OR DVD+R DISCS FOR YOUR BACKUP,BUT SUPPORTED MEDIA*FOR IMAGE BACKUPS INCLUDE:FOR FACTORY IMAGE, DAR, APPLICATION DATA,AND BOOTABLE DISC: DVD-R/+R.FOR USER-CREATED BACKUP IMAGE: DVD-R/+R, DVD-RW/+RW, DVD-DL. * DEPENDING UPON YOUR OPTICAL DRIVE AND MEDIA FORMAT USED,SOME MEDIA TYPES MAY BE INCOMPATIBLEFOR CREATING IMAGE BACKUPS.DUE TO CERTAIN LICENSING REQUIREMENTS,SOME THIRD-PARTY APPLICATIONS WILL NEED TO BE INSTALLEDSEPARATELY USING THE APPLICATION MEDIA BUNDLED WITH YOUR SYSTEM.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-116.png)
![112 - Restoring Your Pre-installed SoftwareAfter you launch the ClickMe! utility when you first start up your system, you should make a copy of the Factory Image to DVD discs. You will need several blank discs (DVD-R or DVD+R discs are recommended) in order to create the copy. After creating the copy, be sure to label the discs and keep them in a safe place to ensure they do not get damaged.Creating Backup Images of Factory Image, DAR, and DiscsUsing the [Manage/Change] button, you can create backup images of the Factory Image, DAR, Application Disc, or Bootable Disc.1Launch My Recovery from the desktop icon.2Select [Manage/Create] -> [Backup Images] The Backup Images menu displays a list from which you can choose which type of disc you want to burn: Bootable Disc, Drivers and Applications Restore Disc, Application Disc, or Recovery Disc.3Select Recovery Disc, then click [Make DVD]4Confirm that the # box has “2” (Note that in some cases the box may display a larger number for the factory image, depending upon its size.)5The message “Recovery Disc #1. will be created. Enter your comments and number of media on the DVD”. Click [YES] to burn the Factory Image.6While the copy is being made, a “Writing to the media” screen displays a progress bar. When the copy is complete, a dialog will appear informing you of the successful completion of the backup.SOME CONFIGURATIONS OF CERTAIN LIFEBOOK MODELS DO NOT HAVE APPLICATIONS LOADED ON THE HARD DRIVE;RATHER,THEY ARE LOADED ON THE DAR DISC. PLEASE TAKE THAT INTO ACCOUNT WHEN READING THE FOLLOWINGPROCEDURES.IN THE FOLLOWING STEP,DO NOT USE THE SYSTEM UNTIL THE COPY IS COMPLETE.DRAFTkfhkfh](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-117.png)
![113 - Restoring Your Pre-installed Software7Repeat the process for the remaining three images on disc (Bootable Disc, Drivers and Applications Restore Disc, and Application Disc). The number of images available may vary depending on your system model; some models do not have the applications loaded on the hard drive.Recovering Your Factory ImageIn the event you need to restore your original Factory Image, perform the following steps. Note that there may be some third-party applications that need to be installed from the application media bundled with your system.In order to recover your Factory Image, perform the steps outlined in “Running Recovery and Utility from hard disk” on page 3. Backing Up a System ImageUser-Configured System Backups: On your desktop, there is a [MyRecovery] icon that allows you to make backups of your current system image either to another location on your hard drive or on removable media. A system image is the configuration of your C: drive at a particular point of time. You may want to make system image backups occasionally in order to have points to which you can return without having to go all the way back to the Factory Image.By default, system images are saved in the D: drive in the MyRecovery folder. You can also elect to save the image to an external hard drive.1Click the [MyRecovery] icon on your desktop.2Click the [Backup] button on the MyRecovery screen.3On the next screen that appears, you can enter up to 200 characters of information about the backup file. This information will help you to identify the image at a later date.4Click the [OK] button and the system will reboot.ALL USER-CREATED DATA WILL BE DELETED FROM YOUR SYSTEM WHEN THE FACTORY IMAGE IS RESTORED.My RecoveryDRAFTli ti R tli ti R t](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-118.png)
![114 - Restoring Your Pre-installed Software5After rebooting, the “Creating of the backup image” window appears, in which you can either click [Create the image on D drive] or [Select the drive] if you want to save to an external hard disk drive.6An image appears showing you graphically how the image will be stored. Click the [Next] button.7Click [Execute] to start the backup. DRAFTli k [C t thli k [C t th](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-119.png)
![115 - Restoring Your Pre-installed SoftwareManaging Your Backup ImagesWith the MyRecovery tool you can also make copies of backup images, archive them on DVD, or delete them from your hard drive.1To begin, click the [MyRecovery] icon on your desktop.2Click the [Manage/Create] button in the MyRecovery window.3When the MyRecovery Manager window appears, click [Manage Backup Images].4In the next window, a list of your backup images appears. Below the list are three buttons allowing you to [Make DVD], [Copy], or [Delete] your backup images.5Select an image title from the list, then click the action button you would like to perform.6Note that you need to have an external disk drive connected for the [Copy] button to be enabled. If you elect to copy the image, you will be prompted to enter the destination. If you are ready to copy, click [OK] to proceed. A progress screen appears while the backup copy is being made.7Note that if you copy an image to an external hard drive, both the original and the copy will appear in the [Backup Images] window with identical names, dates, and file sizes, but with the different drive letter to distinguish them. Before you select [Make DVD], be sure you have a recordable DVD drive connected and blank DVDs available.Using the Recovery and Utility ToolsThe Recovery and Utility tools consist of a variety of tools that will help you recover your Factory Image, recover system images, and delete the data from your hard disk.Methods for accessing the utilities Recovery and Utility Tools are preinstalled in a hidden partition by the factory, or they can be accessed by using the bootable disc. Please note that you can delete Recovery and Utility tools from your hard disk drive if you modify the partitions. In this case you will not be able to use the hidden partition for booting to Recovery and Utility Tools, but you will still be able to boot from the disc.Determining whether Recovery and Utility is pre-loaded 1Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. 2From the Boot Menu that appears, check whether the <Recovery and Utility> option is present. If it is not present, it means that the utility must be used from the disc. Proceed to “Running Recovery and Utility from the Bootable Disc” if <Recovery and Utility> is unavailable.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-120.png)
![116 - Restoring Your Pre-installed Software3You can also use the SecureCore menu to determine whether the utility is pre-loaded by powering on your system then pressing the [Enter] key when the Fujitsu logo appears on the screen. The SecureCore Menu will appear and the Recovery and Utility option will appear in the menu.Running Recovery and Utility from hard disk 1Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. 2Cursor down to <Recovery and Utility> and press the [Enter] key.3While the files are being loaded from the disc, a progress bar will appear at the bottom of the screen.4When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next].5When the Operating System dialog appears, select “Use recovery tools...”, then click [Next]. 6If necessary, enter your password, then click [OK].7When System Recovery Options window appears, click on Recovery and Utility.8The Recovery and Utility screen appears on the screen with three tabs: Diagnostics, Recovery and Utility. Please note that Diagnostics tab is not supported on certain LifeBook/Stylistic models when running Recovery and Utility from the hard disk. In order to restore the operating system, please use the middle icon “Restoring the Factory Image (only C:\drive)” under the Recovery tab. Running Recovery and Utility from the Bootable disc To verify/change boot-up priority (rather than booting-up from a hard drive or external floppy drive), perform the following steps:1Power on your system. When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the SecureCore™ Menu will appear. 2Select the Boot Menu from the SecureCore Menu.3Highlight the CD/DVD option.4Insert the bootable disc into the drive tray.5Click [OK]. While the files are being loaded from the disc, a progress bar will appear at the bottom of the screen.THE BOOTABLE DISC CAN ONLY BE USED WITH THE SYSTEM WITH WHICH IT WAS PURCHASED.DRAFTii](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-121.png)
![117 - Restoring Your Pre-installed Software6When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next].7When the Operating System dialog appears, click [Next]. 8If necessary, enter your password, then click [OK].9When System Recovery Options window appears, click on Recovery and Utility.10 When the Recovery and Utility screen appears, three tabs will be present: Diagnostics, Recovery, and Utility.Recovery and Utility tabs Diagnostics tab: The Diagnostics tool is designed for use by IT professionals. It is not likely you will need to use this tool. When you select devices from the Diagnosis window then click [Execute], several tests are performed on the selected components.Recovery tab: The Recovery tab contains three tools: Recovering User-Configured System Backups, Restoring the Factory Image (only C: drive), and Restoring the Factory Image (full hard drive recovery). You can use these tools to restore the Factory Image from the hidden partition, restore backup image(s) you created or images stored on DVD discs, and perform a full hard drive recovery. Refer to instructions above for details on how to create Factory Image Recovery DVDs, user backup DVDs and system image backup.Utility tab: The Utility tab contains three tools: Hard Disk Data Delete, Restore Recovery and Utility, and Windows Complete PC Restore.•The Hard Disk Data Delete utility is used to delete all data on the hard disk and prevent the data from being reused. NOTE: Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions.•Restore Recovery and Utility allows you to restore the first hidden partition.•Windows Complete PC Restore utility allows you to restore an image created with Windows Backup and Restore Center. Windows Complete PC Restore will overwrite the data on your hard disk drive.DRAFTth li k [N t]th li k [N t]](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-122.png)
![118 - Restoring Your Pre-installed SoftwareRecovering your Factory Image using Recovery and Utility(new or non-bootable hard drive)If you have installed a new hard drive or your hard drive is not bootable, perform the following steps. Note that first you will need to create new partitions on the hard drive, then restore the Factory Image:1Power on your system. When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the SecureCore™ Menu will appear. 2Select the Boot Menu from the SecureCore Menu.3Highlight the CD/DVD option.4Insert the bootable disc in your DVD drive, then click [OK].5When System Recovery Options window appears, click on <Recovery and Utility>.6When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next].7When the Operating System dialog appears, click [Next]. 8If necessary, enter your password, then click [OK].9When System Recovery Options window appears, click on <Recovery and Utility>.10 Click the Recovery tab in the Recovery and Utility window, then click <Restoring the Factory Image (full hard drive recovery> icon.11 Click [Execute].12 Read the precautions, then select “I Agree”. 13 Click [Next], then click [Next] to start the recovery process. 14 “1. Recovery Disc Check” will be in bold and the rest will be grayed out. Follow the instructions and “Insert the Recovery Disc #1”. In some cases, you may prompted to “Insert the Recovery Disc #2”, depending upon the size of the Recovery Image15 Click [Next] to begin the check. Click [Next] again when the check is complete.16 “2. Initializing hard disk drive” will be in bold with the message “Please insert the Bootable Disc into your optical drive”. Insert the bootable disc. Click [Next] to proceed. A dialog box appears, with a checking disc message.17 “Warning All DATA on the Hard Disk will be completely erased!!!” will appear. Select [OK]. The partition creation process will begin.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-123.png)
![119 - Restoring Your Pre-installed Software18 “3. Restoring Factory Image to hidden partition” will be in bold with the message “Please insert the Recovery Disk#1 into the optical drive”. Click [Next] to proceed.19 After completion, the tool will automatically go back to "3.Restoring Factory Image to hidden partition" but will include the note "Please insert your Application Disc(s) starting with #1, then click [OK]. After installation of each disc, insert the next and continue until all have been installed. If you don't have your Application Disc(s) or you have inserted all your application discs. Please click [Cancel] to continue." At this point, you can either:•Insert Application Disc(s) to restore back to hidden partition, or, •Click [Cancel] to skip restoring Application disc(s) and continue with restore.20 If you select to insert Application Disc, after copying of application disc(s) to hidden partition is completed, the message will appear again. Repeat inserting application disc(s) until all discs have been copied, then click [Cancel] to continue with Restore.21 After clicking [Cancel], a confirmation message will appear "If you want to skip copying or copy has been finished, click [OK]. Click [Cancel] to return to Restoring Factory Image to hidden partition." 22 Click [OK] and Restoring Factory Image will begin.23 When restoration is complete, you will see the message “Restoration has been completed. Click [OK] to reboot the computer.” Click [OK].Automatically Downloading Driver UpdatesYour system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system.The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one). If the icon does not appear in the system tray, go to [Start] -> All Programs, and click on Fujitsu Driver Update; this will create the icon automatically.To invoke the FDU menu, right-click on the FDU icon. The menu contains the following items:DRAFTttth Rth R](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-124.png)
![120 - Restoring Your Pre-installed SoftwareCheck for updates now Allows for manual driver update search. The first time it is used, you are prompted to agree to a user agreement. After you click the icon, FDU automatically connects with the Fujitsu site to check for updates and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be used while the download is in process. When the update is complete, a message appears informing you.Enable Automatic Update NotificationsAutomatically searches for new updates on a regular basis (approximately every 3 days).Show update history Brings up a screen that displays a history of updates that have been made via the FDU.About Fujitsu Driver UpdateDisplays the FDU version number and copyright information.Fujitsu Driver Update ReadmeDisplays the FDU readme.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-125.png)
![121 Chapter 5 Care and MaintenanceCaring for your LIFEBOOK Tablet PCIf you use your Fujitsu LIFEBOOK Tablet PC carefully, you will increase its life and reliability. This section provides some tips for looking after the Tablet PC and its devices.THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATICDISCHARGE (ESD). TO MINIMIZE RISK TO THE COMPONENTS,OBSERVE THE FOLLOWING PRECAUTIONS:•BEFORE DOCKING OR UNDOCKING YOUR LIFEBOOK TABLET PC (WHEN USING A PORTREPLICATOR), IT IS A GOOD PRACTICE TO ALWAYS TOUCH A GROUNDED METAL OBJECT TODISCHARGE STATIC ELECTRICITY BUILT UP IN YOUR BODY.•BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING SYSTEM COMPONENTS.EVEN IF THE SYSTEM IS IN HIBERNATE OR SLEEP STATES,DATA COULD BE LOST OR MEMORY COULDBE DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.•WHEN INSTALLING OR REMOVING A MEMORY MODULE,HOLD IT BY THE EDGE SO AS NOT TO TOUCHANY CONTACTS OR CHIPS. BE CAREFUL NOT TO TOUCH ANY INTERNAL COMPUTER TERMINALS ORCOMPONENTS;THE OIL FROM YOUR FINGERS COULD CAUSE A SHORT TO THE COMPONENTS.•ELECTRICAL EQUIPMENT MAY BE HAZARDOUS IF MISUSED. OPERATIONS OF THIS PRODUCT OR SIMILARPRODUCTS,MUST ALWAYS BE SUPERVISED BY AN ADULT. DO NOT ALLOW CHILDREN ACCESS TO THEINTERIOR OF ANY ELECTRICAL PRODUCTS AND DO NOT PERMIT THEM TO HANDLE ANY CABLES.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-126.png)
![122 - Caring for your LIFEBOOK Tablet PC•Your LIFEBOOK Tablet PC is a durable but sensitive electronic device. Treat it with care.•Make a habit of transporting it in a suitable carrying case.•Do not attempt to service the computer yourself. Always follow installation instructions closely.•Keep it away from food and beverages.•To protect your Tablet PC from damage and to optimize system performance, be sure to keep all air vents unobstructed,clean, and clear of debris. This may require periodic cleaning, depending upon the environment in which the system is used. •Do not operate the Tablet PC in areas where the air vents can be obstructed, such as in tight enclosures or on soft surfaces like a bed or cushion.•If you accidentally spill liquid on your LIFEBOOK Tablet PC:1Turn it off.2Position it so that the liquid can run out.3Let it dry out for 24 hours, or longer if needed.4If your Tablet PC will not boot after it has dried out, call your support representative.•Do not use your Fujitsu LIFEBOOK Tablet PC in a wet environment (near a bathtub, swimming pool).•Always use the AC adapter and batteries that are approved for your Tablet PC.•Avoid exposure to sand, dust and other environmental hazards.•Do not expose your Tablet PC to direct sunlight for long periods of time as temperatures above 140° F (60° C) may damage your Tablet PC.•Keep the covers closed on the connectors and slots when they are not in use.•Do not put heavy or sharp objects on the computer.•If you are carrying your LIFEBOOK Tablet PC in a briefcase, or any other carrying case, make sure that there are no objects in the case pressing on the lid.•Never position your Tablet PC such that the optical drive is supporting the weight of the Tablet PC. DRAFThh](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-127.png)
![123 - Caring for your LIFEBOOK Tablet PCCleaning your LIFEBOOK Tablet PC•Always disconnect the power plug. (Pull the plug, not the cord.)•Clean your LIFEBOOK Tablet PC with a damp, lint-free cloth. Do not use abrasives or solvents.•Use a soft cloth to remove dust from the screen. Never use glass cleaners.•Always shut down the computer, unplug the power adapter, and remove the battery when cleaning or disinfecting the computer exterior, keyboard or LCD display. NOTE: Avoid wetting the thermal suede in all cases.Cleaning guidelines using recommended off-the-shelf cleaners Computer exterior, computer keyboardTo clean the exterior and keyboard, use one of the following off-the-shelf products:•Office Depot® #154-616 Notebook Cleaning Kit•Meridrew Enterprises Klear Screen® Wipes•3M CL563 Cleaner WipesNote: After cleaning with one of these products, gently polish with a dry, soft, lint-free cloth until the solution is no longer visible.LCD display To clean the LCD display, use one of the following off-the-shelf products: •Office Depot® #154-616 Notebook Cleaning Kit•Meridrew Enterprises Klear Screen® WipesApplies to Tablet PC, convertible PC with LCD shield, and standard notebook LCD displays.Wipe the LCD surface gently, allowing it to dry before turning on the computer./DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-128.png)
![124 - Caring for your LIFEBOOK Tablet PCDisinfecting LIFEBOOK computers•Wipe the surface with a soft cloth wipe and a 50% ethanol solution or use another ethanol-based germicide which has been registered as a hospital disinfectant by the EPA.Cleaning the dust filterYour LIFEBOOK is equipped with fans to make air flow inside by pulling in outside air to cool the inside of the system. Depending on the environment in which the system is used, dust and dirt may be pulled in along with the air. Accumulated dust and dirt could impair the function of the system.•USE OF INCORRECT CLEANERS CAN RESULT IN OPTICAL IMPAIRMENT OF THE LCD AND/OR DAMAGE TO THECOMPUTER. ALWAYS REFER TO THE CLEANER MANUFACTURER'S GUIDELINES AND MATERIAL SAFETY DATA SHEETSFOR PROPER HANDLING AND USE OF THE PRODUCTS.•NEVER USE AMMONIA,ACIDIC,OR ALKALINE CLEANERS OR ORGANIC CHEMICALS SUCH AS PAINT THINNER,ACETONE,PROPYL OR ISOPROPYL ALCOHOL,OR KEROSENE. IT MAY DAMAGE SURFACE FINISHES AND THECOATING OF THE LCD SCREEN.•NEVER USE COMPRESSED AIR FOR CLEANING STYLISTIC AND LIFEBOOK PCS.•REMOVE AC ADAPTER: BEFORE REMOVING THE FILTER,TURN OFF THE SYSTEM AND PERIPHERALS ANDDISCONNECT THE AC ADAPTER.•CLEANING THE FILTER:- DO NOT USE DETERGENT- AVOID DAMAGING THE FILTER;DAMAGE TO THE FILTER IS NOT COVERED BY WARRANTY.- USE PLASTIC TOOLS TO CLEAN THE FILTER. METAL OR WOODEN TOOLS COULD DAMAGE THE FILTER.•ESD: BEFORE CLEANING THE FILTER,TOUCH A METAL OBJECT TO DISCHARGE STATIC ELECTRICITY.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-129.png)
![125 - Caring for your LIFEBOOK Tablet PCStoring your LIFEBOOK Tablet PC•If storing your Tablet PC for a month or longer, turn it off, fully charge the battery, then remove and store all Lithium ion batteries.•Store the Tablet PC and batteries separately. If you store your tablet with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a bad battery might damage the system.•Store your Fujitsu LIFEBOOK in a cool, dry location. Temperatures should remain between 13ºF (-25ºC) and 140ºF (60ºC).1Turn off your computer and disconnect the AC adapter.2Close the display panel and turn the system upside down. 3Remove the dust filter by pressing the latch towards the filter and lifting it out (Figure 45).4Carefully clean the dust filter and the air-cooling duct.5Put back the dust filter by inserting the end without latch first and pushing in the filter until it latches.Figure 49. ALWAYS BE SURE THE DUST FILTER IS INSTALLED WHEN RUNNING YOUR SYSTEM. NOT USING THEFILTER COULD CAUSE CONTAMINATION AND POSSIBLE DAMAGE TO THE SYSTEM.Dust Filter CoverFilter Cover LatchDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-130.png)
![126 - Caring for your LIFEBOOK Tablet PCTraveling with your LIFEBOOK Tablet PC•Do not transport your Tablet PC while it is turned on. •It is recommended that you carry your Tablet PC with you while traveling, rather than checking it in as baggage.•Always bring your System Recovery CD that came with your Tablet PC when you travel. If you experience system software problems while traveling, you may need it to correct any problems. •Never put your Tablet PC through a metal detector. Have your Tablet PC hand-inspected by security personnel. You can however, put your Tablet PC through a properly tuned X-ray machine. To avoid problems, place your Tablet PC close to the entrance of the machine and remove it as soon as possible or have your Tablet PC hand-inspected by security personnel. Security officials may require you to turn your Tablet PC on, so make sure you have a charged battery on hand. •ALWAYS POWER OFF THE COMPUTER BEFORE TRANSPORTING AND/OR PACKAGING IT. AFTER SHUTTING DOWNTHE SYSTEM,WAIT UNTIL THE STATUS LED PANEL INDICATES POWER OFF CONDITION (I.E., NO LIGHTS AREILLUMINATED).•IT IS POSSIBLE THAT THE UNIT MAY NOT AUTOMATICALLY GO TO POWER OFF OR HIBERNATE MODE WHEN YOUCLOSE THE LID. THIS SITUATION MAY OCCUR DUE TO PRE-OS BOOT PASSWORD SECURITY SETTINGS OR SOMEOTHER APPLICATION RUNNING ON THE COMPUTER.•ATTEMPTING TO TRANSPORT THE COMPUTER WHILE POWER IS ON MAY DAMAGE THE TABLET PC DUE TO SHOCKOR OVERHEATING SINCE THE AIR VENTS MAY BE BLOCKED OR RESTRICTED.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-131.png)
![127 - Caring for your LIFEBOOK Tablet PC•Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.BatteriesCaring for your Batteries •Always handle batteries carefully.•Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.•Do not drop, puncture, disassemble, mutilate or incinerate the battery.•Recharge batteries only as described in this manual and only in ventilated areas.•Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.•Do not leave a battery in storage for longer than 6 months without recharging it.Outlet Type Location Outlet Type LocationUnited States, Canada, parts of Latin Amer-ica, Mexico, Japan, Korea, the Philippines, Taiw anUnited Kingdom, Ire-land, Malaysia, Sin-gapore, parts of AfricaRussia and the Commonwealth of Independent States (CIS), most of Europe, parts of Latin America, the Middle East, parts of Africa, Hong Kong, India, most of South AsiaChina, Australia, New ZealandDRAFTdidi](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-132.png)
![128 - Caring for your LIFEBOOK Tablet PCIncreasing Battery Life •Power your Tablet PC through the AC or optional auto/airline adapter whenever possible.•If your Tablet PC is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.•Keep brightness to the lowest level comfortable.•Set the power management for maximum battery life.•Put your Tablet PC in Sleep mode when it is turned on and you are not actually using it.•Limit your media drive access.•Disable the Media Player auto insert notification function.•Always use fully charged batteries.•Eject ExpressCards when not in use.Media CareCaring for your Media (DVD/CD/CD-R) Media discs are precision devices and will function reliably if given reasonable care.•Always store your media disc in its case when it is not in use.•Always handle discs by the edges and avoid touching the surface.•Avoid storing any media discs in extreme temperatures.•Do not bend media discs or set heavy objects on them.•Do not spill liquids on media discs.•Do not scratch or get dust on media discs.•Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.•If a media disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-133.png)
![129 - Caring for your LIFEBOOK Tablet PC•If a media disc is subjected to a sudden change in temperature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry media discs.Caring for your Optical Drive Your optical drive is durable but you must treat it with care. Please pay attention to the following points:•The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.•Avoid using or storing the drive where it will be exposed to extreme temperatures.•Avoid using or storing the drive where it is damp or dusty.•Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.•Avoid using or storing the drive where it will be subjected to shock or vibration.•Do not disassemble or dismantle the optical drive.•Use of a commercially available lens cleaner is recommended for regular maintenance of your drive.ExpressCardsCaring for your Cards ExpressCards are durable, but you must treat them with care. The documentation supplied with your card will provide specific information, but you should pay attention to the following points:•To keep out dust and dirt, store cards in their protective sleeves when they are not installed in your Tablet PC.•Avoid prolonged exposure to direct sunlight or excessive heat.•Keep the cards dry.•Do not flex or bend the cards, and do not place heavy objects on top of them.•Do not force cards into the slot.•Avoid dropping cards, or subjecting them to excessive vibration.DRAFTifif](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-134.png)
![130 Chapter 6 System SpecificationsSpecificationsThis section provides the hardware and environmental specifications for your Fujitsu LIFEBOOK Tablet PC. Specifications of particular configurations will vary.Configuration LabelThe configuration label located on the bottom of your Tablet PC contains specific information regarding the options you’ve chosen for your Tablet PC. Following is an example configuration label.T901, i5-2520M, 13.3 WXGA, W7Pro, 160G, 2GBConfiguration P/N: A37XXXXXXXXXXXXFPC P/N: FPCXXXXXXHard Drive Part NumberProcessorModel # MemoryOperating System Screen Size/TypeConfiguration ID](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-135.png)
![131 - SpecificationsMicroprocessorNew 2nd Generation Intel® Core™ Processor family. (Refer to system label to determine your processor.)Chipset•Mobile Intel® QM67 Express•Platform Control Hub (PCH)MemorySystem Memory•DDR3-1333 MHz SDRAM dual-channel memory module.•Two DIMM slots; upgradeable to 8 GB of total memory (4 GB x 2). Cache MemoryUp to 4 MB L3 cache on-die (depending upon CPU)VideoBuilt-in color flat-panel TFT active matrix LED backlit display with simultaneous display capability.Video Color and Resolution13.3" Wide XGA display •Internal: 1280 x 800 pixel resolution, 16M colors•External: 1920 x 1200 pixel resolution, 16M colors•Simultaneous: 1280 x 800, 16M colors•Indoor or indoor/outdoor display options (not available on systems with dual digitizer option)Video RAMIntel® HD Graphics with dynamic frequency. Automatically distributes performance to CPU and graphics applications that need an extra boost up to approximately 20%. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-136.png)
![132 - SpecificationsDigitizerDepending upon the configuration of your system, one of two digitizer options is included:•Active digitizer (uses active stylus input), or,•Dual Digitizer, consisting of active digitizer and capacitive touch panel (uses active stylus input and two finger touch input).Audio•Realtek codec ALC269 with High Definition (HD) audio.•Headphones: Stereo headphone jack, 3.5 mm, 1 Vrms or less, minimum impedance 32 Ohms•Microphone: Stereo microphone jack, 3.5 mm, 100 mVp-p or less, minimum impedance 10K Ohms•Two built-in speakers, 25 mm x 16 mm•Two built-in digital microphonesMass Storage Device OptionsHard DriveSerial ATA, 150 Mbps data buffer, 2.5”, 9.5 mm, shock-mounted with Shock Sensor utility. Capacity and speed of the hard drive are determined by system configuration.Modular Bay DevicesOne of the following devices is pre-installed: •TBD - Blu-ray?•Dual-Layer Multi-Format DVD Writer: 24x CD-ROM, 24x CD-R, 10x CD-RW, 8x DVD-ROM, 5x DVD-RAM, 8x DVD+/-R, 4x DVD+/-R(DL), 6x DVD-RW, 8x DVD+RW•Modular Bay Battery•Modular Hard Drive•Weight SaverDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-137.png)
![133 - SpecificationsFeaturesIntegrated Pointing DeviceTouchpad cursor control buttons, with scroll strip built-inCommunications•Gigabit LAN: Intel wired 10/100/1000 Gigabit Ethernet LAN•WLAN: Optional Integrated Intel Centrino Advanced-N 6205 (802.11abgn 2x2), or, Atheros HB116 WLAN (802.11abgn 2x2)•Bluetooth: Bluetooth V3 device for wireless personal area network communication LIFEBOOK Security/Tablet PC PanelTrusted Platform ModuleThe LIFEBOOK T901 has a Trusted Platform Module (TPM) installed for added system security.Theft Prevention LockLock slot for use with security restraint systems.Web CameraBuilt-in 2.0 megapixel web camera with access indicator LEDButton Label Button Function Default Application1 Application A Notepad2 Application B Calculator3 Internet Internet Explorer4 E-Mail OutlookFigure 50. Application Launcher DefaultsDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-138.png)
![134 - SpecificationsDevice PortsOn the LIFEBOOK Tablet PC:•ExpressCard slot for one ExpressCard•Mini-card slot•Memory Stick/SD Card slot•HDMI Port•One 15-pin D-SUB connector for VGA external monitor (see Display specifications)•One USB 3.0 connector for input/output devices•Two USB 2.0 connectors for input/output devices (one of which features Anytime USB Charge support)•One DC In connector•One IEEE 1394 (4-pin type) jack•One LAN (RJ-45) connector•One modem (RJ-11) connector (on certain configurations)•Docking port (100-pin, to dock with port replicator)•One stereo headphone/line-out jack •One stereo microphone/line-in jack•Dedicated Smart Card slot (requires third-party application)On the Optional Port Replicator:•One 15-pin D-SUB connector for VGA external monitor•Four USB 2.0 connectors for input/output devices•One LAN (RJ-45) connector •One DC-in connector•One DVI-D connector•One DisplayPort connector](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-139.png)
![135 - Specifications•One Line-Out connector•Docking connector (100-pin, to dock with system)KeyboardBuilt-in keyboard with all functions of 101 key keyboard.•Total number of keys: 84•Function keys: F1 through F12, plus Fn extension key•Two Windows keys: one Start key, one application key •Key pitch: 19 mm; key stroke: 3.0 mm•Built-in Touchpad pointing device with left and right buttons and scroll strip.•Built-in Palm Rest•Spill-resistant•External USB keyboard/mouse supportPowerBatteries•Standard Lithium ion battery, rechargeable, 6-cell 10.8V, 5800 mAh, or, •Lithium ion battery, rechargeable, 6-cell 10.8V, 6200 mAh•Optional 6-cell Lithium ion modular bay battery, rechargeable, 10.8V, 3800 mAh AC AdapterAutosensing 100-240V AC, supplying 19V DC, 4.22A, 80W to the LIFEBOOK; includes an AC cablePower ManagementConforms to ACPI (Advanced Configuration and Power Interface).DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-140.png)
![136 - SpecificationsDimensions and WeightOverall DimensionsActive Digitizer model: 12.56"(w) x 9.61"(d) x 1.44/1.52”(h) (319 mm x 244 mm x 36.5/38.5 mm)Dual Digitizer model: 12.56"(w) x 9.61"(d) x 1.45/1.54”(h) (319 mm x 244 mm x 37/39 mm)WeightActive Digitizer model:With weight saver: 4.59 lbs. (2.08 kg)With optical drive: 4.96 lbs. (2.25 kg)With bay battery: 5.20 lbs. (2.36 kg)Dual Digitizer model:With weight saver: 4.78 lbs. (2.17 kg)With optical drive: 5.16 lbs. (2.34 kg)With bay battery: 5.40 lbs. (2.45 kg)Environmental RequirementsTemperatureOperating: 41° to 95° F (5° to 35° C). Non-operating: 5° to 140° F (–15° to 60° C)HumidityOperating: 20% to 85%, relative, non-condensing. Non-operating: 8% to 85%, relative, non-condensingAltitudeOperating: 10,000 feet (3,048 m) maximumDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-141.png)
![137 - SpecificationsPopular AccessoriesFor ordering or additional information on Fujitsu accessories please visit our Web site at www.shopfujitsu.com or call 1-800-FUJITSU.Pre-Installed SoftwareDepending on your operating system, your Tablet PC comes with pre-installed software for playing audio and video files of various formats. In addition there is file transfer software and virus protection software. •Adobe Reader•Norton Internet Security™ 2011 (60-day free trial)•CyberLink PowerDirector •CyberLink PowerDVD•CyberLink MakeDisc•CyberLink YouCam•Google Toolbar•Roxio Creator•Fujitsu Touch Launcher (Windows 7 dual digitizer models only)•Fujitsu Driver Update utility•OmniPass Fingerprint application•Microsoft Windows Live Essentials•Microsoft Office 2010 Starter EditionTHE FOLLOWING LIST CONSTITUTES THE SOFTWARE THAT MAY BE INSTALLED ON YOUR COMPUTER.THE PRE-INSTALLED SOFTWARE MAY VARY,AND IS DETERMINED BY YOUR OPERATING SYSTEM ANDCONFIGURATION.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-142.png)
![138 - SpecificationsLearning About Your SoftwareTutorialsAll operating systems and most application software have tutorials built into them upon installation. We highly recommend that you step through the tutorial before you use an application.ManualsIncluded with your Tablet PC you will find manuals for your installed operating system and other pre-installed software. Any manuals that are not included are available online through the software’s “Help” menu. We recommend that you review these manuals for information on the use of these applications.Adobe ReaderAdobe Reader allows you to view, navigate, and print PDF files across all major computing platforms.Norton Internet Security 2009Your system is preinstalled with a free 60-day trial version of Symantec’s Norton Internet Security™ 2009. Internet Security is a suite of tools designed to protect your LIFEBOOK from viruses, hackers, spam, and spyware. It helps you protect data currently on your hard disk from destruction or contamination. The trial version is activated upon your acceptance of software license agreement. After 60 days, you will need to purchase a subscription from Symantec to download latest virus, spyware, and spam definitions.CyberLink MakeDiscCyberLink MakeDisc allows you to burn data, videos and photographs to CDs or DVDs.CyberLink PowerDVDCyberLink PowerDVD allows you to produce and edit home movies and slideshows on discs. CyberLink YouCam CyberLink YouCam allows you to capture photos or movies on the embedded webcam, add special effects to them, and share them in a variety of formats or via social networks. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-143.png)
![139 - SpecificationsCyberLink PowerDirector CyberLink PowerDirector allows you to edit and enhance your videos, and add special effects to them.Google ToolbarGoogle Toolbar lets you to search the Internet quickly, block pop-ups, and perform a variety of other tasks to make your Internet experience easier and more pleasant.OmniPass Fingerprint applicationThe fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass lets you use a "master password" for all Windows, applications, and on-line passwords, and presents a convenient user interface through which you can securely manage passwords, users, and multiple identities for each user.Roxio CreatorRoxio Creator lets you burn CDs and organize, edit and share digital photos, music, data, or videos.Fujitsu Driver Update UtilityThe Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. See“Automatically Downloading Driver Updates” on page 121.Fujitsu Touch Launcher(Windows 7 dual digitizer models only) The Touch Launcher is a handy on-screen method for quickly launching commonly-used applications and performing Internet tasks.Microsoft Windows Live Essentials Windows Live Essentials is a suite of programs that make it easier and more enjoyable to use your notebook. Live Essentials consists of four Live applications: Messenger, Photo Gallery, Writer, and Mail. Messenger lets you communicate and interact with individuals and groups. Photo Gallery lets you organize, edit, and share your photos. Writer can be used to generate blog entries, upload videos and photos to your blogs, and publish entries online. Mail makes it easy for you to manage your email.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-144.png)
![140 - SpecificationsMicrosoft Office Starter 2010 Edition Office Starter 2010 Edition is a software suite containing basic tools for writing letters and reports, tracking family and friends with address books, managing home finances, and creating a home inventory.Microsoft Office Starter 2010 Edition contains Office Word Starter 2010 for writing, editing, and viewing documents, and Office Excel Starter 2010 for creating and viewing spreadsheets. Office Starter 2010 edition also contains full versions of Office Home & Student 2010, Office Home & Business 2010, and Office Professional 2010. These full-featured suites can be accessed by purchasing a Product Key Card.Operating System Microsoft Windows 7 Professional EditionDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-145.png)
![141 GlossaryAC AdapterA device which converts the AC voltage from a wall outlet to the DC voltage needed to power your system.Access pointWireless network device used to bridge wireless and wired network traffic. ACPIAdvanced Configuration and Power InterfaceActive-Matrix DisplayA type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.Ad Hoc ModeAd Hoc Mode refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion.AGPAccelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-146.png)
![142 - GlossaryAuto/Airline AdapterA device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LIFEBOOK Tablet PC.BIOSBasic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LIFEBOOK Tablet PC when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with information on the configuration and status of the hardware.BitAn abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).bpsAn abbreviation for bits per second. Used to describe data transfer rates.BootTo start-up a computer and load its operating system from disk, ROM or other storage media into RAM.BusAn electrical circuit which passes data between the CPU and the sub-assemblies inside your LIFEBOOK Tablet PC.Byte8 bits of parallel binary information.Cache MemoryA block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-147.png)
![143 - GlossaryCD-ROMCompact disk read only memory. This is a form of digital data storage which is read optically with a laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not subject to heads crashing into the surface and destroying the data when there is a failure nor to wear from reading.ChannelRange of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11 channels, 22 MHz wide channels.CMOS RAMComplementary metal oxide semiconductor random access memory. This is a technology for manufacturing random access memory which requires very low levels of power to operate.CommandAn instruction which you give your operating system. Example: run a particular application or format a floppy disk.ConfigurationThe combination of hardware and software that makes up your system and how it is allocated for use.CRTCathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam.DataThe information a system stores and processes.DCDirect current. A voltage or current that does not fluctuate periodically with time.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-148.png)
![144 - GlossaryDefault ValueA pre-programmed value to be used if you fail to set your own.DHCPDynamic Host Configuration Protocol. A protocol used to automatically acquire parameters required for the communication, such as IP address. The sender of IP address is called a DHCP server, and the receiver is called a DHCP client.DIMMDual-in-line memory module.DiskA spinning platter of magnetic data storage media.Disk DriveThe hardware which spins the disk and has the heads and control circuitry for reading and writing the data.DMADirect Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.DMIDesktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software components, and peripherals.DNSDomain Name System. A function to control the association between the IP address and the name assigned to the computer. If you do not know the IP address but if you know the computer name, you can still communicate to that computer.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-149.png)
![145 - GlossaryDOSDisk Operating System (MS-DOS is a Microsoft Disk Operating System).DriverA computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.DVMTDynamic Video Memory Technology. A video memory architecture that increases the efficiency of the motherboard by using innovative memory utilization and direct AGP.ECPExtended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices.Encryption Key (Network Key)Data encryption key used to encrypt message text and for computing message integrity checks. Data encryption protects data from unauthorized viewing.This device uses the same encryption key to encode and decode the data, and the identical encryption key is required between the sender and receiver.ESDElectro-Static Discharge. The sudden discharge of electricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.FCCFederal Communications Commission.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-150.png)
![146 - GlossaryGBGigabyte. One billion bytes.Hard driveA spinning platter of magnetic data storage media where the platter is stiff.I/OInput/Output. Data entering and leaving your Tablet PC in electronic form.I/O PortThe connector and associated control circuits for data entering and leaving your Tablet PC in electronic form.IDEIntelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.IEEE802.11aWireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the 5 GHz lower and middle UNII bands. IEEE802.11bWireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the 2.4 GHz ISM band. IEEE802.11gWireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11g devices operate in the 2.4 GHz ISM band. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-151.png)
![147 - GlossaryIEEE802.11nWireless LAN standard using multiple data streams supporting a maximum data rate of 450 Mbps. 802.11n devices operate in both the 2.4 GHz and 5 GHz UNII bands and are backward compatible with 802.11g and 802.11a.InfrastructureA name of a wireless LAN configuration. This type of communication uses an access point. Another type of communication is called Ad Hoc.IP AddressAn identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 1.160.10.240 could be an IP address. Within an isolated network, you can assign IP addresses at random as long as each one is unique. However,connecting a private network to the Internet requires using registered IP addresses (called Internet addresses) to avoid duplicates. The four numbers in an IP address are used in different ways to identify a particular network and a host on that network. Three regional Internet registries -- ARIN, RIPE NCC and APNIC -- assign Internet addresses from the following three classes. Class A - supports 16 million hosts on each of 126 networks Class B - supports 65,000 hosts on each of 16,000 networks Class C - supports 254 hosts on each of 2 million networks The number of unassigned Internet addresses is running out, so a new classless scheme called CIDR is gradually replacing the system based on classes A, B, and C and is tied to adoption of IPv6.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-152.png)
![148 - GlossaryIRQInterrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.KB Kilobyte. One thousand bytes.LANLocal Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.LCDLiquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.Lithium ion BatteryA type of rechargeable battery which has a high power-time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.MAC Address Media Access Control Address. A unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards. For Ethernet, frames are sent and received based on this address.MBMegabyte. One million bytes.Megahertz1,000,000 cycles per second.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-153.png)
![149 - GlossaryMemoryA repository for data and applications which is readily accessible to your LIFEBOOK Tablet PC’s CPU.MHzMegahertz.MIDIMusical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers.ModemA contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.MonauralA system using one channel to process sound from all sources.MTUMaximum Transmission UnitThe maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large.Network keyData that is used for encrypting data in data communication. The personal computer uses the same network key both for data encryption and decryption, therefore, it is necessary to set the same network key as the other side of communication.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-154.png)
![150 - GlossaryNetwork name (SSID: Service Set Identifier )When a wireless LAN network is configured, grouping is performed to avoid interference or data theft. This grouping is performed with “Network name (SSID)”. In order to improve security, the network key is set allowing no communication unless “Network name (SSID)” coincides with the network key.NTSCNational TV Standards Commission. The standard for TV broadcast and reception for the USA.Open system authenticationNull authentication method specified in the 802.11 standard that performs no authentication checks on a wireless client before allowing it to associate.Operating SystemA group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of microprocessor in order to produce the desired results from that particular equipment.PartitionA block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.PCMCIAPCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.Peripheral DeviceA piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-155.png)
![151 - GlossaryPitch (keyboard)The distance between the centers of the letter keys of a keyboard.PixelThe smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.POSTPower On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your Tablet PC. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation cannot continue, the operating system will not be loaded. PPPoEPoint to Point Protocol over Ethernet. A protocol for Ethernet, using a Point-to-Point Protocol (PPP), which is used for connection on the phone line.ProgramSet of coded commands to your computers telling your hardware what to do and how and when to do it.ProtocolProcedures and rules use to send and receive data between computers.- Method of sending and receiving data- Process used to handle communication errorsConditions required for communication are organized in procedures for correct transfer of information.RAMRandom Access Memory. A hardware component of your LIFEBOOK Tablet PC that holds binary information (both program and data) as long as it has the proper power applied to it.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-156.png)
![152 - GlossaryRAM ModuleA printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.ResetThe act of reloading the operating system. A reset erases all information stored in RAM.ResumeTo proceed after interruption. In your Tablet PC this refers to returning to active operation after having been in one of the suspension states.ROMRead Only Memory. A form of memory in which information is stored by physically altering the material. Data stored in this way cannot be changed by your Tablet PC and does not require power to maintain it.SDRAMSynchronous Dynamic Random Access Memory.Shared key authentication802.11 network authentication method in which the AP sends the client device a challenge text packet that the client must then encrypt with the correct WEP key and return to the AP. If the client has the wrong key or no key, authentication will fail and the client will not be allowed to associate with the AP. Shared key authentication is not considered secure, because a hacker who detects both the clear-text challenge and the same challenge encrypted with a WEP key can decipher the key.SleepTo make inoperative for a period of time. Your LIFEBOOK Tablet PC uses various suspension states to reduce power consumption and prolong the charge of your battery.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-157.png)
![153 - GlossarySSIDService Set Identifier, a 32-character unique identifier attached to the header of packets sent over a WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID. Because the SSID is broadcast in plain text, it does not supply any security to the network. Status IndicatorA display which reports the condition of some portion of your hardware. On your LIFEBOOK Tablet PC this is an LCD screen just above the keyboard.Stereo (audio)A system using two channels to process sound from two different sources.Subnet maskTCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address consists of the subnet address and the address of each computer. Subnet mask defines how many bits of IP address comprise the subnet address. The same value shall be set among computers communicating with each other.SVGASuper VGA.S-VideoSuper Video. A component video system for driving a TV or computer monitor.System ClockAn oscillator of fixed precise frequency which synchronizes the operation of the system and is counted to provide time of day and date.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-158.png)
![154 - GlossaryTCP/IPTransmission Control Protocol/Internet Protocol. A standard Internet protocol that is most widely used.TFTThin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.ULUnderwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices.USBUniversal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such as game pads, pointing devices, printers, and keyboards to your computer.VRAMVideo Random Access Memory. A memory dedicated to video display data and control.WFMWired for Management is Intel’s broad-based initiative to reduce the total cost of ownership (TCO) of business computing without sacrificing power and flexibility.Wi-Fi CompatibleWi-Fi (Wireless Fidelity). Identifies that a product has passed an interoperability test supplied by WECA (Wireless Ethernet Compatibility Alliance), which guarantees the interoperability of wireless IEEE 802.11 LAN products.WLANWireless Local Area Network. A wireless interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-159.png)
![155 - Regulatory InformationRegulatory InformationNoticeChanges or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.FCC NOTICESNotice to Users of Radios and TelevisionThis equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet that is on a different circuit than the receiver.•Consult the dealer or an experienced radio/TV technician for help.Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-160.png)
![156 - Regulatory InformationNotice to Users of the US Telephone NetworkThis equipment complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this information or number must be provided to the telephone company.This equipment is designed to be connected to the telephone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.The ringer equivalent number (REN) of this equipment is 0.1B as shown on the label. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu America, Inc. Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-161.png)
![157 - Regulatory InformationThe equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equipment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual.DOC (INDUSTRY CANADA) NOTICESNotice to Users of Radios and TelevisionThis Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.DRAFTCiCi](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-162.png)
![158 - Regulatory InformationBefore connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility.Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.Avis Aux Utilisateurs Du Réseau Téléphonique CanadienAVIS: Le présent matériel est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal. Cette conformité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel.FOR SAFETY,USERS SHOULD ENSURE THAT THE ELECTRICAL GROUND OF THE POWER UTILITY,THETELEPHONE LINES AND THE METALLIC WATER PIPES ARE CONNECTED TOGETHER. USERS SHOULDNOT ATTEMPT TO MAKE SUCH CONNECTIONS THEMSELVES BUT SHOULD CONTACT THE APPROPRIATEELECTRIC INSPECTION AUTHORITY OR ELECTRICIAN. THIS MAY BE PARTICULARLY IMPORTANT IN RURALAREAS.DRAFTiibliibl](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-163.png)
![159 - Regulatory Information Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.1B. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.POUR ASSURER LA SÉCURITÉ,LES UTILISATEURS DOIVENT VÉRIFIER QUE LA PRISE DE TERRE DUSERVICE D’ÉLECTRICITÉ,LES LIGNES TÉLPHONIQUES ET LES CONDUITES D’EAU MÉTALLIQUES SONTCONNECTÉES ENSEMBLE. LES UTILISATEURS NE DOIVENT PAS TENTER D’ÉTABLIR CES CONNEXIONSEUX-MÊMES,MAIS DOIVENT CONTACTER LES SERVICES D’INSPECTION D’INSTALLATIONS ÉLECTRIQUESAPPROPRIÉS OU UN ÉLECTRICIEN. CECI PEUT ÊTRE PARTICULIÈREMENT IMPORTANT EN RÉGIONSRURALES.DRAFT’il i d’il i d](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-164.png)
![160 Appendix A: WLAN User’s Guide FCC Regulatory InformationPlease note the following regulatory information related to the optional wireless LAN device.Regulatory Notes and StatementsWireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:•On board an airplane, or•In an explosive environment, or•In situations where the interference risk to other devices or services is perceived or identified as harmful.In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-165.png)
![161Regulatory Information/DisclaimersInstallation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure tocomply with these guidelines. This device must not be co-located or operated in conjunction with any other antenna or transmitter.For IEEE 802.11a Wireless LAN: For operation within 5.15~5.25 GHz frequency range, it is restricted to indoor environments, and the antenna of this device must be integral.Federal Communications Commission statementThis device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device.FCC Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions,it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:1Reorient or relocate the receiving antenna.2Increase the distance between the equipment and the receiver.3Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.4Consult the dealer or an experienced radio/TV technician for help.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-166.png)
![162FCC Radio Frequency Exposure statementThe available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposure have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not beenconfirmed by additional research. The wireless LAN radio device has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65.Export restrictionsThis product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu America, Inc. may invalidate the user's right to operate this equipment.Canadian NoticeThe device for the 5150 - 5250 MHz band is only for indoor usage to reduce the potential for harmful interference to co-channelmobile satellite systems.The maximum antenna gain of 6 dBi permitted (for devices in the 5250 - 5350 MHz, 5470 - 5725 MHz and 5725 - 5825 MHz bands) to comply with the e.i.r.p. limit as stated in A9.2 of RSS210.In addition, users are cautioned to take note that high power radars are allocated as primary users (meaning they have priority)of 5250 - 5350 MHz and 5650 - 5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-167.png)
![163 Before Using the Optional Wireless LANBefore Using the Optional Wireless LANThis manual describes the procedures required to properly set up and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure its correct operation. Keep this manual in a safe place for future reference.Wireless LAN Device Covered by this DocumentThis document is applicable to systems containing one of the following optional devices:•Integrated Intel Centrino Advanced-N 6205 (802.11a/b/g/n)•Atheros HB116 (802.11a/b/g/n)Characteristics of the WLAN Device•The WLAN device is a Mini-PCI card attached to the main board of the mobile computer. •The WLAN device operates in license-free RF bands, eliminating the need to procure an FCC operating license. The WLAN operates in the 2.4GHz Industrial, Scientific, and Medical (ISM) RF band and the lower, middle, and upper bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands. •The WLAN devices are capable of four operating modes, IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n•The WLAN devices are Wi-Fi certified and operate (as applicable) at a the maximum data rate of 540 Mbps (theoretical) in IEEE802.11n mode; 54 Mbps in IEEE802.11a or IEEE802.11g mode; and 11 Mbps in IEEE802.11b mode.•The WLAN devices support the following encryption methods - WEP, TKIP, CKIP, and AES encryption.•The Wireless LAN devices are compliant with the following standards: WPA, WPA2, CCX1.0, CCX2.0, CCX3.0, and CCX4.0.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-168.png)
![164 Before Using the Optional Wireless LANWireless LAN Modes Using this DeviceAd Hoc Mode"Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive method for establishing network connectivity between multiple computers. Ad Hoc mode requires that the SSID, network authentication, and encryption key settings are identically configured on all computers in the Ad Hoc network.Figure 51. Ad Hoc Mode Network](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-169.png)
![165 Before Using the Optional Wireless LANAccess Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the WLAN in order to access services, devices, and computers (e.g., file servers, printers, databases).Figure 52. Access Point (Infrastructure) Mode NetworkADSL modem,cable modem,or similarInternet Wired LANAccess Point*Wireless LAN *An optional hub for a wiredLAN may be required dependingupon the type of access point used.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-170.png)
![166 Before Using the Optional Wireless LANHow to Handle This DeviceThe WLAN device is an optional device that may come pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. •The Wireless LAN devices support IEEE802.11a, IEEE802.11b, IEEE802.11g, and IEEE802.11n.•The WLAN devices operate in the 2.4 GHz ISM band and the 5 GHz lower, middle, and upper UNII bands.•Microwave ovens may interfere with the operation of WLAN devices since they operate in the same 2.4 GHz frequency range as IEEE802.11b/g/n devices. Interference by microwaves does not occur with IEEE802.11a radio which operates in the 5 GHz RF band.•Wireless devices that transmit in the 2.4 GHz range may interfere with operation of WLAN devices in IEEE802.11b/g/n modes. Symptoms of interference include reduced throughput, intermittent disconnects, and many frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure proper operation of the WLAN device.Deactivating/Disconnecting the WLAN DeviceDisconnecting the WLAN device may be desired in certain circumstances (to extend battery life) or where certain environments require it (i.e. hospitals, clinics, airplanes, etc.). The WLAN device can be deactivated by using the Wireless On/Off Switch, and it can be disconnected in Windows using the WLAN icon in the system tray (Note that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected.).BEFORE USING THE WIRELESS LAN DEVICE,YOU MUST FIRST INSTALL CLICKME!TO ENSURE THATTHE CORRECT SOFTWARE FOR YOUR DEVICE IS INSTALLED. SEE “INSTALLING CLICKME!” ON PAGE 68.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-171.png)
![167 Before Using the Optional Wireless LANDeactivation Using the Wireless On/Off SwitchThe WLAN device can be deactivated quickly and efficiently by toggling the Wireless Device On/Off Switch to the Off position. The switch has no effect on non-Wireless LAN models.Figure 53. Wireless Device On/Off Switch LocationDisconnection Using the Icon in the TaskbarNote that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit and receive even though it’s not connected.1Right-click the WLAN icon in the taskbar at the bottom right of your screen.2Choose Disconnect from a network.Activating the WLAN DeviceActivation of the WLAN device can be accomplished using the same methods as the deactivation process•Using the Wireless On/Off Switch•In Windows, by right-clicking the WLAN icon then clicking “Connect to a network”Wireless Device SwitchDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-172.png)
![168 Configuring the Wireless LANConfiguring the Wireless LANThe optional WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows. Support for most industry standard security solutions is contained in this software.Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters:Configuring the WLAN1Click the Start button, then select Control Panel. (If you are in Windows Vista and the Control Panel is not in Classic View, select Classic View from the left panel.)2Double-click the Network and Sharing Center icon.3Select “Manage wireless networks” from the left panel.4Click on the [Add] button.5Depending upon what type of connection you would like to make, make a selection. For an infrastructure network, select “Manually create a network profile. For ad hoc network, select “Create an ad hoc network”.6Enter the required information. If necessary, consult with your network administrator for some of the information.7In the event you require assistance, go to the Network and Sharing Center window (Start -> Control Panel -> Network and Sharing Center), and type in relevant keywords in the Search box. Connecting to a NetworkAfter you have configured your computer, you can connect to an active network by performing the following steps:1Click on the WLAN icon in the system tray.2Select “Connect to a network”.3Select a network from the list that appears, and click the [Connect] button.Connection to the networkAfter you have configured your computer, you can connect to an active network by clicking on the Wireless Network icon in the system tray:](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-173.png)
![169 Troubleshooting the WLANTroubleshooting the WLANTroubleshootingCauses and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. If you are unfamiliar with the steps required, consult your System Administrator or go to [Start] -> Help and Support -> Networking and the WebProblem Possible Cause Possible SolutionUnavailable network connectionIncorrect network name (SSID) or network keyAd hoc connection: verify that the network names (SSID’s) and network keys (WEP) of all computers to be connected have been configured correctly. SSID’s and WEP key values must be identical on each machine.Access Point (Infrastructure) connection: set network name (SSID) and network key to the same values as those of the access point. Set the Network Authentication value identically to that of the Access Point. Please consult your network administrator for this value, if necessary. Weak received signal strength and/or link qualityAd hoc connection: Retry connection after shortening the distance to the destination computer or removing any obstacles for better sight.Access Point (Infrastructure) connection: Retry connection after shortening the distance to the access point or removing any obstacles for better transmission.The WLAN device has been deactivated or disabledCheck if the wireless switch is turned On. Go to Start -> Control Panel, and double-click on Windows Mobility Center. If the wireless network is off, click the [Turn wireless on] button. The computer to be connected is turned offCheck if the computer to be connected is turned ON.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-174.png)
![170 Troubleshooting the WLANUnavailable network connection(continued)RF interference from Access Points or other wireless networksThe use of identical or overlapping RF channels can cause interference with the operation of the WLAN device. Change the channel of your Access Point to a channel that does not overlap with the interfering device.Wireless network authentication has failedRe-check your Network Authentication, Encryption, and Security settings. Incorrectly configured security settings such as an incorrectly typed WEP key, a misconfigured LEAP username, or an incorrectly chosen authentication method will cause the LAN device to associate but not authenticate to the wireless network.Incorrectlyconfigured network settingsRecheck the configuration of your network settings.Incorrect IP address configurationThis only applies to networks using static IP addresses. Please contact your network administrator for the correct settings.Problem Possible Cause Possible SolutionDRAFTFDRAF](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-175.png)
![171 WLAN SpecificationsWLAN SpecificationsSpecificationsItem SpecificationType of network The integrated Intel Centrino Advanced-N 6205 (802.11abgn 2x2) and Atheros HB116 (802.11a/b/g/n) WLAN devices conform to IEEE 802.11a, 802.11b/g, and 802.11n, Wi-Fi based*.Transfer rate (Automatic switching) 54 Mbps maximum data rate (IEEE802.11n to be determined)Active frequency •802.11n: 2.4 GHz or 5 GHz•802.11b/g: 2400~2473 MHz •802.11a: 4900 ~ 5850 MHzTypical operating distances** •802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps•802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps•802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps•802.11n: Estimated double the operating distance of 802.11g and 802.11a in their respective frequencies.Number of channels •802.11a: 8 independent channels•802.11b/g: 11 channels, 3 non-overlapping channels •802.11n: 2.4 GHz - 3 non-overlapping channels when Channel Bonding is not used; 2 non-overlapping channels when Channel Bonding is used.5 GHz - 12 non-overlapping UNII channels with or without Channel Bonding Security Encryption Types - WEP, TKIP, AES***, WPA 1.0 compliant Encryption Key lengths Supported: 64 bits and 128 bits 802.1x/EAPMaximum recommended number of computers to be connected over wireless LAN (during ad hoc connection)10 units or less ****DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-176.png)
![172 WLAN Specifications* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.** The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources.*** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/ 104 bits after subtracting the fixed length of 24 bits.**** Depending on practical environments, the allowable number of computers to be connected may be decreased.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-177.png)
![173 Using the Bluetooth DeviceUsing the Bluetooth DeviceThe Integrated Bluetooth module (EYSMJCS) is a wireless device installed in selected Fujitsu mobile computers. What is BluetoothBluetooth technology is designed as a short-range wireless link between mobile devices, such as laptop computers, phones, printers, and cameras. Bluetooth technology is used to create Personal Area Networks (PANs) between devices in short-range of each other. Where to Find Information About BluetoothThe Bluetooth module contains a robust Help user’s guide to assist you in learning about operation of the Bluetooth device.To access the Help file, click [Start] -> All Programs, and click on Bluetooth, then select User’s Guide.For additional information about Bluetooth Technology, visit the Bluetooth Web site at: www.bluetooth.com.THE WIRELESS LAN/BLUETOOTH ON/OFF SWITCH WILL POWER OFF BOTH THE OPTIONAL WIRELESSLAN AND BLUETOOTH DEVICES AT THE SAME TIME. TO ENABLE OR DISABLE EITHER ONE OF THEDEVICES INDIVIDUALLY,PERFORM THE FOLLOWING STEPS:1Slide the Wireless LAN/Bluetooth on/off switch to On position.2Go to Start > All Programs > Bluetooth.3Click on Options under the Bluetooth menu and click on the Bluetooth Radio Powerbutton. 4Click [OK].DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-178.png)
![174 Using the Bluetooth DeviceFCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The internal Bluetooth antenna is located on the left rear corner of the base unit (just behind the [F1]/[F2]/[F3] keys) and is exempt from minimum distance criteria due to its low power. The transmitters in this device must not be co-located or operated in conjunction with any other antenna or transmitter.Canadian NoticeTo prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.WarrantyUsers are not authorized to modify this product. Any modifications invalidate the warranty.This equipment may not be modified, altered, or changed in any way without signed written permission from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and Industry Canada and the warranty.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-179.png)
![175 Appendix B: Fingerprint Sensor DeviceIntroducing the Fingerprint Sensor DeviceYour system has a fingerprint sensor device at the bottom left below the display screen. Figure 54. Fingerprint sensorWith a fingerprint sensor, you can avoid having to enter a username and password every time you want to:•Log onto Windows•Resume from sleep mode•Cancel a password-protected screen saver•Log into homepages that require a username and passwordFingerprintSensor DeviceDRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-180.png)
![176 - Introducing the Fingerprint Sensor DeviceAfter you have “enrolled” - or registered - your fingerprint, you can simply swipe your fingertip over the sensor for the system recognize you. The fingerprint sensor uses Softex OmniPass which provides password management capabilities to Microsoft Windows operating systems. OmniPass enables you to use a "master password" for all Windows, applications, and on-line passwords. OmniPass requires users to authenticate themselves using the fingerprint sensor before granting access to the Windows desktop. This device results in a secure authentication system for restricting access to your computer, applications, web sites, and other password-protected resources.OmniPass presents a convenient graphical user interface, through which you can securely manage passwords, users, and multiple identities for each user.Getting StartedThis section guides you through the preparation of your system for the OmniPass fingerprint recognition application. You will be led through the OmniPass installation process. You will also be led through the procedure of enrolling your first user into OmniPass. Installing OmniPassIf OmniPass has already been installed on your system, skip this section and go directly to “User Enrollment” on page 179. You can determine whether OmniPass has already been installed by checking to see if the following are present:•The gold key-shaped OmniPass icon in the system tray at the bottom right of the screen.•The Softex program group in the Programs group of the Start menuSystem RequirementsThe OmniPass application requires space on your hard drive; it also requires specific Operating Systems (OS’s). The minimum requirements are as follows:DRAFTihih](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-181.png)
![177 - Introducing the Fingerprint Sensor Device•Windows XP Professional operating system or later•At least 35 MB available hard disk spaceInstalling the OmniPass ApplicationIf OmniPass is already installed on your system, go to “User Enrollment” on page 179. Otherwise continue with this section on software installation.To install OmniPass on your system you must:1Insert the installation media for the OmniPass application into the appropriate drive. If you are installing from CD-ROM or DVD-ROM, you must find and launch the OmniPass installation program (setup.exe) from the media.2Follow the directions provided in the OmniPass installation program. Specify a location to which you would like OmniPass installed.It is recommended that you NOT install OmniPass in the root directory (e.g. C:\). 3Once OmniPass has completed installation you will be prompted to restart you system. Once your system has rebooted you will be able to use OmniPass. If you choose not to restart immediately after installation, OmniPass will not be available for use until the next reboot.4The installation program automatically places an icon (Softex OmniPass) in the Windows Control Panel as well as a golden key shaped icon in the taskbar. Verifying Information about OmniPassAfter you have completed installing OmniPass and restarted your system, you may wish to check the version of OmniPass on your system.•INSTALLATION OF THE APPLICATION REQUIRES THAT YOU HAVE AN EXTERNAL OPTICAL DRIVE ATTACHED TOYOUR SYSTEM.•FOR INSTALLATION, OMNIPASS REQUIRES THAT THE USER INSTALLING OMNIPASS HAVE ADMINISTRATIVEPRIVILEGES TO THE SYSTEM. IF YOUR CURRENT USER DOES NOT HAVE ADMINISTRATIVE PRIVILEGES,LOG OUTAND THEN LOG IN WITH AN ADMINISTRATOR USER BEFORE PROCEEDING WITH OMNIPASS INSTALLATION.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-182.png)
![178 - Introducing the Fingerprint Sensor DeviceTo check the version information of OmniPass:1From the Windows Desktop, double-click the key-shaped OmniPass icon in the taskbar (usually located in the lower right corner of the screen),or,Click the Start button and click Control Panel. Double-click Softex OmniPass in the Control Panel, and the OmniPass Control Center will appear. If it does not appear, then the program is not properly installed,or,Click the Start button, select Programs, and from the submenu select the Softex program group, from that submenu click OmniPass Control Center.2Select the About tab at the top of the OmniPass Control Center. The About tab window appears with version information about OmniPass.Uninstalling OmniPassTo remove the OmniPass application from your system:1Click Start on the Windows taskbar. Select Settings, and then Control Panel.2Double-click Add/Remove Programs (In Windows 7: Programs and Features).3Select OmniPass, and then click Change/Remove.4Follow the directions to uninstall the OmniPass application.5Once OmniPass has finished uninstalling, reboot your system when prompted.FOR UNINSTALLATION, OMNIPASS REQUIRES THAT THE USER UNINSTALLING OMNIPASS HAVEADMINISTRATIVE PRIVILEGES TO THE SYSTEM. IF YOUR CURRENT USER DOES NOT HAVEADMINISTRATIVE PRIVILEGES,LOG OUT AND THEN LOG IN WITH AN ADMINISTRATOR USER BEFOREPROCEEDING WITH OMNIPASS UNINSTALLATION.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-183.png)
![179 - Introducing the Fingerprint Sensor DeviceUser EnrollmentBefore you can use any OmniPass features you must first enroll a user into OmniPass.Master Password ConceptComputer resources are often protected with passwords. Whether you are logging into your computer, accessing email, e-banking, paying bills online, or accessing network resources, you often have to supply credentials to gain access. This can result in dozens of sets of credentials that you have to remember.During user enrollment a "master password” is created for the enrolled user. This master password “replaces” all other passwords for sites you register with OmniPass. Example: A user, John, installs OmniPass on his system (his home computer) and enrolls an OmniPass user with username “John_01” and password “freq14”. He then goes to his webmail site to log onto his account. He inputs his webmail credentials as usual (username “John_02” and password “lifebook”), but instead of clicking [Submit], he directs OmniPass to Remember Password. Now whenever he returns to that site, OmniPass will prompt him to supply access credentials. John enters his OmniPass user credentials (“John_01” and “freq14”) in the OmniPass authentication prompt, and he is allowed into his webmail account. He can do this with as many web sites or password protected resources he likes, and he will gain access to all those sites with his OmniPass user credentials (“John_01” and “freq14”). This is assuming he is accessing those sites with the system onto which he enrolled his OmniPass user. OmniPass does not actually change the credentials of the password protected resource. If John goes to another computer without he OmniPass account to access his webmail, he would need to enter his original webmail credentials (“John_02” and “lifebook”) to gain access. If he attempts his OmniPass user credentials on a system other than a system he’s enrolled on, he will not gain access.THE ENROLLMENT PROCEDURE ASSUMES YOU HAVE NO HARDWARE AUTHENTICATION DEVICES ORALTERNATE STORAGE LOCATIONS THAT YOU WISH TO INTEGRATE WITH OMNIPASS. IF YOU DESIRESUCH FUNCTIONALITY,CONSULT THE APPROPRIATE SECTIONS OF THIS DOCUMENT.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-184.png)
![180 - Introducing the Fingerprint Sensor DeviceBasic EnrollmentThe Enrollment Wizard will guide you through the process of enrolling a user. Unless you specified otherwise, after OmniPass installation the Enrollment Wizard will launch on Windows login. If you do not see the Enrollment Wizard, you can bring it up by clicking Start on the Windows taskbar; select Programs; select Softex; click OmniPass Enrollment Wizard.1Click Enroll to proceed to username and password verification. By default, the OmniPass Enrollment Wizard enters the credentials of the currently logged in Windows user.2Enter the password you use to log in to Windows. This becomes the “master password” for this OmniPass user. In most cases, the Domain: value will be your Windows computer name. In a corporate environment, or when accessing corporate resources, Domain: may not be your Windows computer name. Click [Next] to continue.3In this step OmniPass captures your fingerprint. See “Enrolling a Fingerprint” on page 180 for more information.4Next, choose how OmniPass notifies you of various events. We recommend you keep Taskbar Tips onBeginner mode taskbar tips and Audio Tips on at least Prompt with system beeps only until you get accustomed to how OmniPass operates. Click [Next] to proceed with user enrollment. You will then see a Congratulations screen indicating your completion of user enrollment.5Click [Done] to exit the OmniPass Enrollment Wizard. You will be asked if you’d like to log in to OmniPass with your newly enrolled user; click [Yes].Enrolling a FingerprintEnrolling a fingerprint increases the security of your system and streamlines the authentication procedure. You enroll fingerprints in the OmniPass Control Center. With an OmniPass user logged in, double-click the system tray OmniPass icon. Select the User Settings tab and click Enrollment under the UserSettings area. Click Enroll Authentication Device and authenticate at the authentication prompt to start device enrollment.1During initial user enrollment, you will be prompted to select the finger you wish to enroll. Fingers that have already been enrolled will be marked by a green check. The finger you select to enroll at this time will be marked by a red arrow. OmniPass will allow you re-enroll a finger. If you choose a finger that has already been enrolled and continue enrollment, OmniPass will enroll the fingerprint, overwriting the old fingerprint. Select a finger to enroll and click [Next].DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-185.png)
![181 - Introducing the Fingerprint Sensor Device2It is now time for OmniPass to capture your selected fingerprint. It may take a several capture attempts before OmniPass acquires your fingerprint. Should OmniPass fail to acquire your fingerprint, or if the capture screen times out, click [Back] to restart the fingerprint enrollment process. Your system has a “swipe” fingerprint sensor. A swipe sensor is small and resembles a skinny elongated rectangle. To capture a fingerprint, gently swipe or pull your fingertip over the sensor (starting at the second knuckle) towards yourself. Swiping too fast or too slow will result in a failed capture. The Choose Fingerscreen has a [Practice] button; click it to practice capturing your fingerprint. When you are comfortable with how your fingerprint is captured, proceed to enroll a finger.3Once OmniPass has successfully acquired the fingerprint, the Verify Fingerprint screen will automatically appear. To verify your enrolled fingerprint, place your fingertip on the sensor and hold it there as if you were having a fingerprint captured. Successful fingerprint verification will show a green fingerprint in the capture window and the text Verification Successful under the capture window.Using OmniPassYou are ready to begin using OmniPass. Used regularly, OmniPass will streamline your authentications.Password ReplacementYou will often use the password replacement function. When you go to a restricted access website (e.g., your bank, your web-based email, online auction or payment sites), you are always prompted to enter your login credentials. OmniPass can detect these prompts and you can teach OmniPass your login credentials. The next time you go to that website, you can authenticate with your fingerprint to gain access.OmniPass Authentication ToolbarAfter installing OmniPass and restarting, you will notice a dialog you have not seen before at Windows Logon. This is the OmniPass Authentication Toolbar, and it is displayed whenever the OmniPass authentication system is invoked. The OmniPass authentication system may be invoked frequently: during Windows Logon, during OmniPass Logon, when unlocking your workstation, when resuming from sleep or hibernate, when unlocking a password-enabled screensaver, during password replacement for remembered site or application logins, and more. When you see this toolbar, OmniPass is prompting you to authenticate.DRAFTtt t b ftt t b f](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-186.png)
![182 - Introducing the Fingerprint Sensor DeviceThe Logon Authentication window indicates what OmniPass-restricted function you are attempting. The icons in the lower left (fingerprint and key) show what authentication methods are available to you. Selected authentication methods are highlighted while unselected methods are not. When you click the icon for an unselected authentication method, the authentication prompt associated with that method is displayed.When prompted to authenticate, you must supply the appropriate credentials: an enrolled finger for the fingerprint capture window or your master password for the master password prompt (the key icon).Remembering a PasswordOmniPass can remember any application, GUI, or password protected resource that has a password prompt.Using the following procedure, you can store a set of credentials into OmniPass. These credentials will then be linked to your “master password” or fingerprint.Go to a site that requires a login (username and password), but do not log in yet. At the site login prompt, enter your username and password in the prompted fields, but do not enter the site (do not hit [Enter], [Submit], [OK], or Login). Right-click the OmniPass system tray icon and select Remember Passwordfrom the submenu. The Windows arrow cursor will change to a golden key OmniPass cursor. Click the OmniPass cursor in the login prompt area, but don’t click [Login] or [Submit].Associating a Friendly NameAfter clicking the OmniPass key cursor near the login prompt, OmniPass will prompt you to enter a “friendly name” for this site. You should enter something that reminds you of the website, the company, or the service you are logging into. In its secure database, OmniPass associates this friendly name with this website.Additional Settings for Remembering a SiteWhen OmniPass prompts you to enter a “friendly name” you have the opportunity to set how OmniPass authenticates you to this site. There are three settings for how OmniPass handles a remembered site.DRAFTiThiTh](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-187.png)
![183 - Introducing the Fingerprint Sensor DeviceThe default setting is Automatically click the “OK” or “Submit” button for this password protected site once the user is authenticated. With this setting, each time you navigate to this site OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass, you will automatically be logged into the site.Less secure is the option to Automatically enter this password protected site when it is activated. Do not prompt for authentication. Check the upper box to get this setting, and each time you navigate to this site OmniPass will log you into the site without prompting you to authenticate.If you uncheck both boxes in Settings for this Password Site, OmniPass will prompt you for your master password or fingerprint authentication device. Once you have authenticated with OmniPass your credentials will be filled in to the site login prompt, but you will have to click the website [OK], [Submit], or [Login] button to gain access to the site.Click Finish to complete the remember password procedure. The site location, the credentials to access the site, and the OmniPass authentication settings for the site are now stored in the OmniPass secure database. The OmniPass authentication settings (Settings for this Password Site) can always be changed in Vault Management.Logging in to a Remembered SiteWhether or not OmniPass prompts you to authenticate when you return to a remembered site is determined by Settings for this Password Site and can be changed in Vault Management.The following cases are applicable to using OmniPass to login to: Windows, remembered web sites, and all other password protected resources.THIS SETTING IS MORE CONVENIENT IN THAT WHENEVER YOU GO TO A SITE REMEMBERED WITH THISSETTING,YOU WILL BYPASS ANY AUTHENTICATION PROCEDURE AND GAIN INSTANT ACCESS TO THESITE. BUT SHOULD YOU LEAVE YOUR SYSTEM UNATTENDED WITH YOUR OMNIPASS USER LOGGED IN,ANYONE USING YOUR SYSTEM CAN BROWSE TO YOUR PASSWORD PROTECTED SITES AND GAINAUTOMATIC ACCESS.DRAFTdttddttd](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-188.png)
![184 - Introducing the Fingerprint Sensor DeviceWith Master PasswordOnce you return to a site you have remembered with OmniPass, you may be presented with a master password prompt. Enter your master password and you will be allowed into the site.Logging into Windows with a Fingerprint DeviceWhen logging into Windows with a fingerprint device, the fingerprint capture window will now appear next to the Windows Login screen. Place your enrolled fingertip on the sensor to authenticate. You will be simultaneously logged into Windows and OmniPass. The capture window will also appear if you have used Ctrl-Alt-Del to lock a system, and the fingerprint device can be used to log back in as stated above.Password ManagementOmniPass provides an interface that lets you manage your passwords. To access this GUI, double-click the OmniPass key in the system tray. Click Vault Management; you will be prompted to authenticate. Once you gain access to Vault Management, click Manage Passwords under Vault Settings. You will see the Manage Passwords interface, with a list of friendly names.You can view credentials stored for any remembered website by highlighting the desired resource underPassword Protected Dialog and clicking Unmask Values. Should a password be reset, or an account expire, you can remove stored credentials from OmniPass. Highlight the desired resource under Password Protected Dialog and click Delete Page. You will be prompted to confirm the password deletion.The two check boxes in Manage Passwords govern whether OmniPass prompts you to authenticate or directly logs you into the remembered site.OmniPass will overwrite an old set of credentials for a website if you attempt to use RememberPassword on an already remembered site. IF A MACHINE IS LOCKED AND OMNIPASS DETECTS A DIFFERENT USER LOGGING BACK IN WITH AFINGERPRINT,THE FIRST USER WILL BE LOGGED OUT AND THE SECOND USER LOGGED IN.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-189.png)
![185 - Introducing the Fingerprint Sensor DeviceThe exception to the above rule is when resetting the Windows password. If your password is reset in Windows, the next time you login to Windows, OmniPass will detect the password change and prompt you to “Update” or “Reconfirm” the password with OmniPass. Enter your new Windows password in the prompt and click OK. Your OmniPass "master password" will still be your Windows password.OmniPass User IdentitiesIdentities allow OmniPass users to have multiple accounts to the same site (e.g., bob@biblomail.com and boballen@biblomail.com). If OmniPass did not provide you identities, you would be limited to remembering one account per site.To create and manage identities, double-click the OmniPass key in the system tray. Click Vault Management; OmniPass will prompt you to authenticate. Once you gain access to Vault Management,click Manage Identities under Vault Settings. You can only manage the identities of the currently logged in OmniPass userTo add a new identity, click New Identity or double-click Click here to add a new identity. Name the new identity and click [OK], then click [Apply]. You can now switch to the new identity and start remembering passwords.To delete an identity, highlight the identity you want to delete and click [Delete Identity], then [Apply].To set the default identity, highlight the identity you want as default and click [Set as Default]; click [Apply] to ensure the settings are saved. If you log in to OmniPass with a fingerprint device, you will automatically be logged in to the default identity for that OmniPass user. You can choose the identity with which you are logging in if you login using "master password".WHEN YOU DELETE AN IDENTITY,ALL OF ITS ASSOCIATED REMEMBERED SITES AND PASSWORDPROTECTED DIALOGS ARE LOST.di idi](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-190.png)
![186 - Introducing the Fingerprint Sensor DeviceChoosing User Identity during LoginTo choose your identity during login, type your username in the User Name: field. Press [Tab] and see that the Domain: field self-populates. Click the Password: field to bring the cursor to it, and you will see the pull-down menu in the Identity: field. Select the identity to login as, then click OK.Switch User IdentityTo switch identities at any time, right-click the OmniPass system tray icon and click Switch User Identityfrom the submenu. The Switch Identity dialog will appear. Select the desired identity and then click OK.Identities and Password ManagementOn the Manage Passwords interface of the Vault Management tab of the OmniPass Control Center, there is a pull-down selection box labeled, Identity. This field lets you choose which identity you are managing passwords for. When you select an identity here, only those password protected dialogs that are associated with that identity are shown. You can perform all the functions explained in “Password Management” on page 184.Configuring OmniPassThis section gives an overview of both the Export/Import function and the OmniPass Control Center.Exporting and Importing UsersUsing OmniPass Control Center, you can export and import users in and out of OmniPass. The export process backs up all remembered sites, credentials, and enrolled fingerprints for an OmniPass user. All OmniPass data for a user is backed up to a single encrypted database file. During the import process, the Windows login of the exported user is required. If the proper credentials cannot be supplied, the user profile will not be imported.YOU CANNOT IMPORT A USER INTO OMNIPASS IF THERE ALREADY IS A USER WITH THE SAME NAMEENROLLED IN OMNIPASS.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-191.png)
![187 - Introducing the Fingerprint Sensor DeviceExporting an OmniPass User ProfileTo export a user, open OmniPass Control Center, and click Import/Export User under Manage Users.Click Exports an OmniPass user profile. OmniPass will prompt you to authenticate. Upon successfully authentication, you must name the OmniPass user profile and decide where to save it. An .opi file is generated, and you should store a copy of it in a safe place.This .opi file contains all your user specific OmniPass data, and it is both encrypted and password protected. This user profile does NOT contain any of your encrypted data files.Importing an OmniPass User ProfileTo import an OmniPass user open the OmniPass Control Center, and click Import/Export User under Manage Users. Click Imports a new user into OmniPass and then select OmniPass Import/Export File (*.opi) and click Next. OmniPass will then prompt you to browse for the file you had previously exported (.opi file). When you select the .opi file for importation, OmniPass will prompt you for authentication. The credentials that will allow a user profile to be imported are the Windows login credentials of the exported user. They are the credentials that had to be submitted when the user profile was exported. You will need User Name, Password, and Domain. If you don’t remember the value for Domain, in a PC or SOHO environment Domain should be your computer name.OmniPass will notify you if the user was successfully imported.•YOU SHOULD PERIODICALLY EXPORT YOUR USER PROFILE AND STORE IT IN A SAFE PLACE. IFANYTHING HAPPENS TO YOUR SYSTEM,YOU CAN IMPORT YOUR OMNIPASS PROFILE TO A NEWSYSTEM AND HAVE ALL YOUR REMEMBERED SETTINGS AND FINGERPRINTS INSTANTLY.•YOU DON'T FORGET THE WINDOWS LOGIN CREDENTIALS WHEN EXPORTING. WHEN YOU EXAMINETHE IMPORTATION,YOU ARE PROMPTED FOR AUTHENTICATION. THE CREDENTIALS THAT WILLALLOW A USER PROFILE TO BE IMPORTED ARE THE WINDOWS LOGIN CREDENTIALS OF THEEXPORTED USER. THEY ARE THE CREDENTIALS THAT HAD TO BE SUBMITTED WHEN THE USERPROFILE WAS EXPORTED. YOU WILL NEED USER NAME, PASSWORD,AND DOMAIN.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-192.png)
![188 - Introducing the Fingerprint Sensor DeviceThings to Know Regarding Import/Export•Assume you export a local Windows User profile from OmniPass. You want to import that profile to another machine that has OmniPass. Before you can import the profile, a Windows user with the same login credentials must be created on the machine importing the profile.Example: I have a Windows user with the username “Tom” and the password “Sunshine” on my system. I have enrolled Tom into OmniPass and remembered passwords. I want to take all my passwords to new system. I export Tom’s OmniPass user profile. I go to my new system and using the Control Panel I create a user with the username "Tom" and the password "Sunshine". I can now successfully import the OmniPass user data to the new system.•If you export an OmniPass-only user, you can import that user to any computer running OmniPass, provided that a user with that name is not already enrolled in OmniPass. •If you attempt to import a user profile who has the same name as a user already enrolled in OmniPass, the OmniPass import function will fail.OmniPass Control CenterThis section will serve to explain functions within the OmniPass Control Center that weren’t explained earlier. You can access the OmniPass Control Center any of three ways:•Double-click the golden OmniPass key shaped icon in the Windows taskbar (typically in the lower-right corner of the desktop)•Click the Start button; select the Programs group; select the Softex program group; and click the OmniPass Control Center selection.•Open the Windows Control Panel (accessible via Start button --> Settings --> Control Panel) and double-click the Softex OmniPass icon.](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-193.png)
![189 - Introducing the Fingerprint Sensor DeviceUser ManagementThe User Management tab has two major interfaces: Add/Remove User and Import/Export User.Import/Export User functionality is documented in “Exporting and Importing Users” on page 186.Add/Remove User functionality is straightforward. If you click Adds a new user to OmniPass you will start the OmniPass Enrollment Wizard. The Enrollment Wizard is documented in “User Enrollment” on page 179.If you click Removes a user from OmniPass, OmniPass will prompt you to authenticate. Authenticate with the credentials (or enrolled fingerprint) of the user you wish to remove. OmniPass will prompt you to confirm user removal. Click OK to complete user removal.User SettingsUser Settings tab has four interfaces: Audio Settings,Taskbar Tips, and Enrollment. User settings allow users to customize OmniPass to suit their preferences. Under User Settings (Audio Settings and Taskbar Tips) you set how OmniPass notifies the user of OmniPass events (e.g., successful login, access denied). The details of each setting under the Audio Settings and Taskbar Tips interfaces are self-explanatory.The Enrollment interface allows you to enroll fingerprints. For the procedure to enroll and authentication device refer to Chapter 2.3. To enroll additional fingerprints, click Enroll Authentication Device, and authenticate with OmniPass. Select the fingerprint recognition device in the Select Authentication Device screen (it should already be marked by a green check if you have a finger enrolled) and click Next.System SettingsThe OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon.REMOVING A USER WILL AUTOMATICALLY DESTROY ALL OMNIPASS DATA ASSOCIATED WITH THATUSER. ALL IDENTITIES AND CREDENTIALS ASSOCIATED WITH THE USER WILL BE LOST.IF YOU’RE SURE YOU WANT TO REMOVE THE USER,WE RECOMMEND YOU EXPORT THE USER PROFILE.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-194.png)
![190 - Introducing the Fingerprint Sensor DeviceThe first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. If the user logging into Windows was never enrolled into OmniPass, upon login no one will be logged on to OmniPass. This setting is appropriate for an office setting or any setting where users must enter a username and password to log into a computer. This is the default setting.With the second option, Manually log on to OmniPass at startup, OmniPass will prompt you to login once you have logged on to Windows.With the third option, Do not log on to OmniPass at startup, OmniPass will not prompt for a user to be logged on.You can manually log on to OmniPass by right-clicking the OmniPass taskbar icon and clicking Log in User from the right-click menu.TroubleshootingYou cannot use OmniPass to create Windows users. You must first create the Windows user, and you will need administrative privileges to do that. Once the Windows user is created, you can add that user to OmniPass using the same username and passwordCannot add Windows users to OmniPassIf you experience difficulties adding a Windows user to OmniPass, you may need to adjust your local security settings. You can do this by going to Start, Control Panel,Administrative Tools, and LocalSecurity Settings. Expand Local Policies, expand Security Options, and double-click Network Access: Sharing and Security Model for Local Accounts. The correct setting should be Classic - Local Users Authenticate as Themselves.Cannot add a User with a Blank Password to OmniPassIf you experience difficulties adding a user with a blank password to OmniPass, you may need to adjust your local security settings. First attempt the procedure explained in the Cannot add Windows user to OmniPass section. If the difficulties persist, then try the following procedure.DRAFTidiidi](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-195.png)
![191 - Introducing the Fingerprint Sensor DeviceClick Start, Control Panel, Administrative Tools, and Local Security Settings. Expand Local Policies, expand Security Options, and double-click Accounts: Limit local account use of blank passwords to console login only. This setting should be set to Disabled.Dialog appears after OmniPass authentication during Windows LogonAfter installing OmniPass on your system, you can choose to logon to Windows using OmniPass. You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box.This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). This could happen for any of the following reasons:•Your Windows password has changed•Your Windows account has been disabledIf you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. Click Update Password and you will be prompted with a dialog to reconfirm your password.Enter the new password to your Windows user account and click OK. If the error persists, then it is unlikely the problem is due to your Windows user account password changing.DRAFTddLlLl](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-196.png)
![192 Appendix C: Using Intel® Wireless Display Using the Wireless Display technologyIntel® Wireless Display (WiDi) is a new technology that is available as an option on selected Fujitsu LIFEBOOK computers. If you have Intel WiDi on your system, please read these instructions and information regarding its use.Intel WiDi lets users enjoy and share PC content from an Intel® Core™ processor-based notebook with their big screen TV. With Intel WiDi, you can use your big screen TV to view data and applications from your hard drive, home network, or the Internet. It’s no longer necessary for friends and families to crowd around the PC to enjoy content stored or accessed there.As its name implies, Intel WiDi is a wireless technology. Note, however, that it requires a third-party display adapter in order to be used. The display adapter is attached to the TV via HDMI (preferred) or composite A/V cables.FIRST GENERATION DISPLAY ADAPTERS ARE AVAILABLE FROM ELECTRONICS RETAILERS. ANY DISPLAYADAPTER THAT IS COMPATIBLE WITH INTEL WIRELESS DISPLAY CAN BE USED WITH THIS TECHNOLOGY.IF YOUR TELEVISION HAS HDMI PORTS,THAT IS THE PREFERRED METHOD OF CONNECTION ASOPPOSED TO COMPOSITE CABLE CONNECTION.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-197.png)
![193 - Using the Wireless Display technologyStarting the WiDi applicationTo launch Intel® Wireless Display, perform the following steps:1Verify that you have a display adapter connected to the television on which you want to use WiDi and turn on the television.2If you haven’t yet turned on the wireless device switch on your notebook, do so now.3Click on the WiDi icon on your desktop or the Start menu shortcut.4The PC content is displayed on the big screen TV.After the initial set-up between the laptop and a compatible display adapter, you can set the adapter as the default to auto-connect. In the future, simply opening the application will automatically connect the two.For detailed information about using and troubleshooting the WiDi technology, click on the WiDi icon then click the [Help] button in the upper right-hand corner to open the Wireless Display Help file.•IF YOU PURCHASED A SYSTEM WITH AN INTEL WIRELESS LAN AND OPTIONAL INTEL WIDI TECHNOLOGY,THEWIDI APPLICATION MAY OR MAY NOT BE PRE-INSTALLED (DEPENDING UPOON YOUR SYSTEM CONFIGURATION).SYSTEMS WITH INTEL WIDIPRE-INSTALLED WILL HAVE A WIDI ICON LOCATED ON THEIR DESKTOP. IFTHEICONIS NOT PRESENT, INTEL WIDI WILL BE INSTALLED AS SOON AS YOU RUN CLICKME.•THE INTEL WIDI TECHNOLOGY WILL ONLY WORK IN COMBINATION WITH AN INTEL WIRELESS LAN.•ONLY WINDOWS MEDIA PLAYER CAN BE USED AS THE MEIA PLAYER FOR WIDI 2.0.•BEFORE USING INTEL WIDI,BE SURE THAT THE SYSTEM’S WIRELESS DEVICE SWITCH IS TURNED ON.•NOTE THAT SECURE CONTENTS ARE NOT SUPPORTED BY INTEL WIDI 2.0. CONTENT REQUIRING OUTPUTPROTECTION SUCH AS BLU-RAY®AND DVD MOVIE PLAYBACK IS NOT SUPPORTED BY WIDI.•THERE MAY BE A SLIGHT TIME LAG WHEN USING WIDI WHEN YOU MOVE THE MOUSE OR TYPE IN CHARACTERS.•THE FIRST TIME YOU USE WIDI,THE DEFAULT DISPLAY RESOLUTION IS 1280X720. IF YOU WOULD LIKE TOCHANGE THE RESOLUTION,GO TO THE CONTROL PANEL -> DISPLAY PROPERTIES UNDER THE SETTINGS TAB.ONCE YOU HAVE SET THE RESOLUTION,IT WILL BECOME THE DEFAULT UNLESS YOU CHANGE IT AGAIN.DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-198.png)
![194 IndexAAbout This Guide 1,8ACadapter 68indicator 29plug adapters 135Active Digitizer 45Air Vents 24,27Anti-theft lock slot 22,23Auto/Airline Adapter 68,69BBattery 83care 135cold-swapping 86conserving power 78dead 112faulty 112hot-swapping 86increasing life 136level indicator 29level indicators 29lithium ion battery 83low 85problems 112recharging 84replacing 86shorted 86Standby mode 85Battery Latches 26BIOSguide 74setup utility 73BluetoothWhere to Find Information 187Boot Sequence 72Booting the System 74Built-in Speakers 106Button Icons 56,59CCapacitive Touchscreen 49CapsLock 30CD-ROM 107Click Me! 75Cold-swapping 53Configuration Label 139Contact Information 9Controls and Connectors 13Conventions Used in the Guide 8Cursor Keys 38DDC in connector 13DC Output Cable 68DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-199.png)
![195DC Power Jack 68Device Ports 97DIMM 93Display Panel 16,32brightness 35opening 32problems 114Dock port 13Docking Port 99Double-Clicking 41Dragging 41,43Drivers and Application Restore CD 122Dual Built-in Microphones 18DVD driveproblems 107EError Messages 117ExpressCard Eject Button 20ExpressCard Slot 20ExpressCards 90installing 90problems 110removing 91slot 20External Video Port 14,25,101FFDU 77,126,149Fingerprint Sensor Device 18,189enrolling a fingerprint 195getting started 190installing OmniPass 190logging into a remembered site 199OmniPass authentication toolbar 197password replacement 196remembering a password 197uninstalling OmniPass 192user enrollment 193using OmniPass 195Fujitsu Contact Information 9Fujitsu Driver Update utility 77,126,149Fujitsu LifeBookstoring 132traveling 134Fujitsu Shopping Online 10Function KeyF10 39F3 39F4 39F6 39F7 39F8 39,51F9 39,51FN 39GGestures 49Gigabit LAN (RJ-45) Jack 25Glossary 151HHard Disk Driveaccess indicator 29problems 108Hard Disk Drive Passwords 72Headphone Jack 13,20,101Hibernation Feature 81DRAFT77](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-200.png)
![196disable/enable 81IIEEE 1394 Port 21,100Internal LAN Jack 97,98KKeyboard 16,37cursor keys 38function keys 38numeric keypad 38problems 108windows keys 38LLifeBook Security Paneloperating 63passwords 62setting up 61uninstalling 65LifeBook Security/Tablet PC Buttons 16,55Lithium ion Battery Bay 26Local Area Network (LAN) 14MMedia Playercare 137Memorycapacity 95checking capacity 95compartment 27,94installing 93problems 109removing 95upgrade module 93Memory Stickremoving 89Memory Stick/Secure Digital Cards 88installing 89Microphone Jack 13,21,101Modem 24problems 109Modem (RJ-11) Jack 98Modular Bay 52cold-swapping 53devices 52installing 53removing 53Modular Devices 53installing 53removing 53Mouse problems 108MS/SD Cardinstalling 89NNumLk 30PPen tether 50Pen Tether Attachment Point 20Pointing Device 40Port Replicatorconnector 27problems 108Post-logon button functions 58PowerAC adapter 68DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-201.png)
![197Auto/Airline adapter 68failure 110,111indicator 28management 78off 82on 71problems 113sources 68Power Management 78Power On Self Test 71,117Power/Suspend/Resume Button 16,78Pre-Installed Software 147Adobe Acrobat Reader 148Google Toolbar 148,149manuals 148Pre-logon button functions 56QQuick Point Pointing Device 40RRegistration 77Regulatory Information 168Restarting 81Restoring Your Pre-installed Software 122Right Button 18RJ-11 98RJ-45 97SScrLk 31Scrolling 44SD Cardremoving 89SD/Memory Stick Slot 13SDRAM 27,93Security ButtonsFunctions 55Security lock slot 14Smart Card Reader 92Smart Card Slot 13Specifications 139Audio 141Chipset 140Device Ports 143Dimensions and Weight 145Environmental Requirements 146Keyboard 145mass storage device options 141Memory 140Microprocessor 140Power 145Video 140Starting the first time 74Status Indicator Panel 16,28Suspend/ Resume button 14TTablet Configuration 33Tablet PC Button Functionschanging 61Touch Screencalibrating 48clicking 46dragging 47Touchpad Control Adjustment 44Troubleshooting 103DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-202.png)
![198UUniversal 99USB 2.0 Ports 13,20,23,24,99,109problems 109VVolume control 51WWarranty 10Windows keys 38Application key 38Start keys 38Windows Power Management 81Wireless LANBefore Using the Wireless LAN 176configuring 176connection to the network 182deactivating/disconnecting 179modes 177Specifications 185Troubleshooting 183Wireless LAN/Bluetooth On/Off Switch 14DRAFT](https://usermanual.wiki/Fujitsu-Client-Computing/WL0024.User-Manual/User-Guide-1426872-Page-203.png)