Fujitsu Isotec 019M33334A Dot Matrix Printer User Manual

Fujitsu Isotec Limited Dot Matrix Printer

User Manual

     FUJITSU DL7400Pro DOT MATRIX PRINTER USER'S MANUAL
  READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT. INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO USERS, BYSTANDERS OR PROPERTY. While FUJITSU ISOTEC has sought to ensure the accuracy of all information in this manual, FUJITSU ISOTEC assumes no liability to any party for any damage caused by any error or omission contained in this manual, its updates or supplements, whether such errors or omissions result from negligence, accident, or any other cause. In addition, FUJITSU ISOTEC assumes no liability with respect to the application or use of any product or system in accordance with descriptions or instructions contained herein; including any liability for incidental or consequential damages arising therefrom. FUJITSU ISOTEC DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION CONTAINED HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY. FUJITSU ISOTEC reserves the right to make changes to any products described herein without further notice and without obligation.        This Product is designed, developed and manufactured as contemplated for general use, including without limitation, general office use, personal use, household use, and ordinary industrial use, but is not designed, developed and manufactured as contemplated for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could lead directly to death, personal injury, sever physical damage or other loss(hereinafter “High Safety Required Use”), including without limitation, nuclear control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system. You shall not use this  Product without securing the sufficient safety required for the High Safety Required Use. If you wish to use this Product for  High Safety Required Use, please consult with our sales representatives in charge before such use.     This manual contains technology which is subject to the Foreign Exchange and Foreign Trade Law of Japan. This manual should not be exported or transferred to foreign countries in any from or method, or released to anyone other than the residents of Japan prior obtaining applicable license from your local government or authorities and/ or the Ministry of Economy, Trade and Industry of Japan in accordance with the above law.     IMPORTANT NOTE TO USERSUsing This Product in High-risk SituationsEXPORT CONTROL
    User's Manual  i  Following notes for United States are valid for 100-120V model only.  Federal Communications Commission Radio Frequency Interference Statement  for United States Users NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15B of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.     FCC warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.   NOTES 1.  Testing of this equipment was performed on model number M33334A. 2.  The use of an unshielded  interface cable with the referenced device is prohibited. The length of the parallel interface cable must be 3 meters (10 feet) or less. The length of the optional serial interface cable must be 15 meters (50 feet) or less.  3.  The length of the power cord must be 3 meters (10 feet) or less.
   ii  User's Manual The contents of this manual may be revised without prior notice and without obligation to incorporate changes and improvements into units already shipped. Every effort has been made to ensure that the information included here is complete and accurate at the time of publication; however, Fujitsu Isotec Limited cannot be held responsible for errors and omissions. Printer model specifications differ with the power supply input voltage (M33334A; 100-120 V or M33334B; 220-240 V).  KA02086-Y890-01EN DECEMBER 2015 Copyright © 2015 FUJITSU ISOTEC LIMITED  Printed in Japan. All rights reserved. No part of this manual may be reproduced or translated, stored in a database or retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Fujitsu Isotec Limited.   FUJITSU is a registered trademark and Fujitsu Creative Faces is a trademark of Fujitsu Limited. Centronics is a trademark of Centronics Data Computer Corporation. IBM PC and IBM Proprinter XL24E are trademarks of International Business Machines Corporation. ESC/P2 is a trademark of Seiko Epson Corporation. Microsoft is a registered trademark and MS-DOS and Windows are trademarks of Microsoft Corporation. Nimbus Sans is a registered trademark of URW Unternehmensberatung Karow Rubow Weber GmbH, Hamburg. Other product names mentioned in this manual may also be trademarks of their respective companies. TRADEMARK ACKNOWLEDGEMENT
   User's Manual  iii ABOUT THIS MANUAL Thank you for buying the Fujitsu DL7400Pro dot matrix printer. You can expect years of reliable service with very little maintenance. This manual explains how to use your printer to full advantage. It is written for both new and experienced printer users. This manual describes how to install, set up, and use your printer and printer options. It also explains how to keep the printer in good working condition and what to do should something go wrong. Detailed procedures are provided for first-time users. Experienced users can skip some of the details, using the table of contents and chapter introductions to locate information. This manual has several appendixes, a glossary, and an index. Appendix A lists supplies and additional documentation and information available from your dealer or authorized Fujitsu representative. Fujitsu offices are listed at the end of the manual.  This manual covers model DL7400Pro, a 136-column printer. Each model has a 100-120 V (M33334A) or 220-240 V (M33334B) power supply.  A LAN card, a user add-on option, can be installed only on printer models with the Centronics parallel + USB interfaces. You must specify these when purchasing the printer. Other options include a cut sheet feeder can be added by yourself after purchasing the printer.  DL7400Pro Basic specifications Print line at 10 cpi:  136 columns (DL7400Pro)  Interface:  Centronics parallel + RS-232C   Centronics parallel + USB + LAN (LAN:user option) Alternative specification Power supply:   100-120 V (M33334A)   220-240 V (M33334B) User add-on option LAN card Cut sheet feeder Tractor unit Sound proof cover  Large Stacker Small paper table cpi: characters per inch PRINTER MODELS AND OPTIONS
   iv  User's Manual This manual is organized as follows: Quick Reference summarizes everyday printer operations. After you become familiar with the printer, use this section as a memory aid. Chapter 1, Introduction, introduces the printer and identifies key features and options that enhance the printer’s capabilities. Chapter 2, Setting Up, gives step-by-step procedures for setting up the printer for immediate use and identifies the main parts of the printer. If this is your first printer, you should read the entire chapter before attempting to use the printer. Chapter 3, Paper Handling, explains how to load and use paper with your printer. Chapter 4, Printing, covers basic printing operations. This chapter describes everyday operations from the printer’s control panel, such as loading paper and selecting print features, in detail. After you become more familiar with the printer, use Quick Reference at the beginning of the manual to refresh your memory as needed. Chapter 5, Using Setup Mode, describes how to change the printer’s optional settings, such as print features, hardware options, and top-of-form. Most settings only affect print features such as the typestyle and page format. Note that certain settings directly affect hardware and software compatibility. Refer to this chapter as indicated in Chapter 2 or as required. Chapter 6, Maintenance, explains basic maintenance procedures for this printer. Chapter 7, Trouble-Shooting, describes problem-solving techniques. Before you contact your dealer for help, check the list of problems and solutions provided in this chapter. Chapter 8, Installing Options, describes the options available for the printer and explains how to install them. At the end of this manual, you will find several appendixes, a glossary, and an index. Appendix A gives order numbers for printer supplies, options, and publications. Other appendixes provide additional technical information about the printer. ORGANIZATION
   User's Manual  v Special information, such as warnings, cautions, and notes, are indicated as follows:  WARNING A WARNING indicates that personal injury may result if you do not follow a procedure correctly.  CAUTION A CAUTION indicates that damage to the printer may result if you do not follow a procedure correctly.  NOTE A NOTE provides “how-to” tips or suggestions to help you perform a procedure correctly. NOTEs are particularly useful for first-time users.  For Experienced Users: If you are familiar with this printer or with dot matrix printers in general, this information will help you use the manual effectively.  CONVENTIONS
   viii  User's Manual  Warning symbols Various graphic symbols are used in this manual.  They serve as signs to help users of this product use the product safely and correctly as well as prevent damage and personal injury to the users or bystanders.  The following tables show and explain each symbol.  Be sure that you understand the meaning of each symbol before reading the manual.    WARNING    CAUTION A WARNING indicates that death or serious personal injury may result if you do not follow a procedure correctly. A CAUTION indicates that personal injury or property damage may result if you do not follow a procedure correctly.  Examples and explanations of graphic symbols   indicates a warning or caution item.  By itself, the image in this symbol suggests the meaning of the warning or caution (the example on the left is a caution of possible electric shock).   indicates a prohibited action.  The image in or beside this symbol expresses the prohibited action (the example on the left indicates that disassembly is prohibited).   indicates a direction that must be observed.  The image in this symbol shows the direction (the example on the left shows the direction in which a power plug is disconnected from an outlet).  Caution: Hot This symbol and accompanying statement indicate a risk of injury from a hot object.  Caution: Flammable This symbol and accompanying statement indicate a risk of fire.  Do not touch This symbol and accompanying statement indicate a risk of injury from touching part of the equipment.  Do not disassemble This symbol and accompanying statement indicate a risk of injury, such as from electric shock, caused by disassembling the equipment.  General prohibited action This symbol and accompanying statement indicate a general prohibited action.  General caution This symbol and accompanying statement indicate a general caution.
  User's Manual    ix Notes on Safety  WARNING    WARNING    Do not place a container containing water, such as a vase, potted plant, and drinking glass, or a metal object on or near the printer. Otherwise, electric shock or fire may result. Do not place the printer in a humid or dusty area, in an area with explosive fumes, an area with poor ventilation or close to a fire. Otherwise, electric shock or fire may result. Use only one of the power cords included with this product, for this product.  Do not use any other power cord for this product. Otherwise, electric shock or fire may result.    Do not use this product in an area exposed to a high level of moisture, such as a bathroom and shower room. Otherwise, electric shock or fire may result.
   x  User's Manual   WARNING    When mounting or removing an optional device or component, turn off the power to the printer and personal computer and disconnect their power plugs from the outlets before performing the work. Otherwise, electric shock may result. Connect only Fujitsu-recommended optional devices and components. Otherwise, electric shock, fire, or failure may result.    CAUTION    Do not block openings in the printer (e.g., ventilation openings). If ventilation openings are blocked, heat accumulates inside the printer, possibly resulting in a fire. Do not place a heavy object on the printer.  Also, do not subject the printer to shocks. Otherwise, the printer may become unbalanced, causing it to fall, and possibly resulting in personal injury. Do not place the printer in an area exposed to strong vibration or an unstable area such as on a slope. Otherwise, the printer may fall or topple, possibly resulting in personal injury. Do not leave the printer in an area exposed to direct sunlight for a long time, such as inside a car under the sun or any other area subjected to high temperatures. Otherwise, the printer surface heats up, possibly melting covers or resulting in other deformities, or the inside of the printer may become extremely hot, possibly resulting in fire.    Before moving the printer, be sure to disconnect the power plug from the outlet and disconnect all connected cables from the printer. Otherwise, the power cord may be damaged, possibly resulting in electric shock or fire, or the printer may fall or topple, possibly resulting in personal injury. Before connecting or disconnecting a printer cable, be sure to turn off the power to the printer and personal computer. Performing that and related work without the power turned off may result in a personal computer or printer failure.
  User's Manual    xi   Notes about the printer in operation    WARNING    If the printer is making a strange noise, which indicates a problem, discontinue printer operation.  Request your printer dealer to fix the problem. Continued operation of the printer without repairs may result in electric shock or fire. Do not use a power source whose voltage is other than that indicated.  Also, an excessive number of plugged-in power cords must not be connected to a single outlet. Otherwise, electric shock or fire may result. Do not spill any liquid, such as water, on the printer. Otherwise, electric shock or fire may result. Do not damage or modify the power cord. The power cord may be damaged by placing a heavy object on it, stretching it excessively, forcibly bending it, twisting it, or heating it, and this may result in electric shock or fire. Do not use the power cord if it or the power plug is damaged or the plug does not fit securely in the outlet receptacle. Using the power cord in that condition may result in electric shock or fire. Do not insert the power cord into an outlet or turn on the power to the printer when any of its covers has been removed. Otherwise, electric shock or fire may result. Prevent foreign objects, such as metal shards and inflammable materials, from being inserted or dropped into any openings in the printer (e.g., ventilation openings). Otherwise, electric shock or fire may result. Do not disconnect the power plug from the outlet while the power to the printer is turned on. Otherwise, the plug becomes deformed, possibly resulting in fire.    Do not remove the main printer cover or the cover for the cable connectors except as necessary.  To check and repair internal components, request your printer dealer to do so. Some internal components use high voltage, and touching them may result in electric shock. Do not modify the printer by yourself. Otherwise, electric shock or fire may result.      Do not connect or disconnect the power plug with wet hands. Otherwise, electric shock may result.
   xii  User's Manual   WARNING    If excessive heat, smoke, a strange odor, or a strange noise is coming the printer or any other abnormality is observed, immediately turn off the power to the printer by using the power switch, and be sure to disconnect the power plug from the outlet. Then, after verifying the end of the abnormality (e.g., no more smoke is coming from the printer), request your printer dealer to make repairs.  Do not repair the printer by yourself as doing so is dangerous. Continued use of the printer when it is operating abnormally may result in electric shock or fire. If a foreign object (e.g., water or other liquid, metal shard) has entered the printer, immediately turn off the power to the printer by using the power switch, and disconnect the power plug from the outlet.  Then, contact your printer dealer. Continued use of the printer in that condition may result in electric shock or fire.  Customers who use the printer near children should take especial care regarding this point. If the printer is dropped or a cover is damaged, turn off the power to the printer by using the power switch, and disconnect the power plug from the outlet.  Then, contact your printer dealer. Continued use of printer in that condition may result in electric shock or fire. Before performing cleaning, maintenance, or troubleshooting work on the printer, switch off the power switch, and be sure to disconnect the power plug from the outlet. Performing that work on the printer without the power turned off may result in burns or electric shock.    If dust accumulates on or near the metal parts of the power plug, so wipe away that dust with a dry cloth. Continued use of printer in that condition may result in fire.      Do not drop or strike the printer, such as by hitting it against something. Otherwise, a failure may result.
  User's Manual    xiii   CAUTION    Insert the power plug completely into an outlet so that it is securely connected. Otherwise, electric shock or fire may result. Exercise caution to keep loose clothing, hair, neckties, etc. away from paper feed- or ejection openings, and tractors while the printer is operating. Otherwise, personal injury may result.    When disconnecting the power plug from the outlet, pull it out while grasping the plug, not the cord. If you pull it out while grasping the cord, the insulation may be damaged or the cable core may be exposed or damaged, possibly resulting in electric shock or fire. Do not cover or wrap the printer with a cloth or anything else while it is operating. Otherwise, heat accumulates, possibly resulting in fire. Do not use the power cord with it bunched together. Otherwise, heat accumulates, possibly resulting in fire.      If the printer is not to be used for a long time, disconnect the power plug from the outlet for safety reasons. Otherwise, electric shock or fire may result. If a lightning storm is in nearby, disconnect the power plug from the outlet. Leaving the plug connected to the outlet may result in damage to the printer or other property damage.    The print head and internal frames become extremely hot during printer operation and remain so immediately afterwards.  Do not touch these parts until sufficient time has passed to allow them to cool. Otherwise, burns or personal injury may result.
   xiv  User's Manual   CAUTION    Do not touch the paper feed- or ejection openings  while the printer is operating. Otherwise, personal injury may be result. Do not touch the printer cable connectors or the metal part of the print head. Otherwise, personal injury or a printer failure may result. Do not touch the print head while it is moving. Otherwise, burns or personal injury may result.    Note that continuous forms that are fed in the reverse direction continuously may come off the paper feed tractors. Operate the printer with the paper thickness lever set to the appropriate paper thickness. Use only an original ribbon cassette that is specified as suitable by Fujitsu. Textile fibers accumulate on components inside the printer and parts of the roller, so clean these parts regularly. Do not turn the ribbon feed knob in the reverse direction. Otherwise, the ribbon may become jammed and stuck. If printing is started with a slack ribbon, the ribbon may become tangled or the ribbon feed mechanism may become locked. The print head is extremely hot immediately after printing.  When replacing the ribbon, verify that the print head is sufficiently cool before setting the print head to the ribbon replacement position.
  User's Manual    xv TABLE OF CONTENTS QUICK REFERENCE .................................................. QR-1 CHAPTER 1 INTRODUCTION ....................................................................... 1-1 FEATURES ................................................................... 1-1 MODELS ....................................................................... 1-3 OPTIONS ...................................................................... 1-3 CHAPTER 2 SETTING UP............................................................................. 2-1 SELECTING A GOOD LOCATION ................................. 2-1 UNPACKING THE PRINTER ......................................... 2-2 Checking Options and Supplies ................................. 2-4 ASSEMBLING THE PRINTER ....................................... 2-5 Mounting and removing the tractor unit .....................2-10 GETTING ACQUAINTED WITH YOUR PRINTER .........2-13 CONNECTING THE POWER CORD ............................2-16 TESTING THE PRINTER (OFFLINE) ............................2-17 Loading Paper for the Self-Test ................................2-17 Printing the Self-Test ................................................2-18 CONNECTING THE PRINTER TO YOUR COMPUTER .................................................................2-21 Selecting a Parallel Interface Cable ..........................2-21 Selecting a Serial Interface Cable.............................2-21 Selecting a USB Cable .............................................2-22 Selecting a LAN cable ..............................................2-22 Connecting the Interface Cable ................................2-22 SELECTING AN EMULATION ......................................2-23 PRINTING A SAMPLE PAGE (ONLINE) .......................2-27 INSTALLING THE PRINTER DRIVER...........................2-28 CHAPTER 3 PAPER HANDLING .................................................................. 3-1 SELECTING PAPER...................................................... 3-1 OVERVIEW OF PAPER OPERATIONS ......................... 3-2 SELECTING PAPER PATH ........................................... 3-5 Paper Paths and Feed Directions ADJUSTING FOR PAPER THICKNESS ........................ 3-9 USING SINGLE SHEETS .............................................3-10 Loading a Single Sheet of Paper ..............................3-10 Loading Paper from the Cut Sheet Feeder (Option)....................................................................3-13 Ejecting Single Sheets .............................................3-15 USING CONTINUOUS FORMS ....................................3-15 Positioning the Paper Stack .....................................3-16 Loading Continuous Forms (Front Feed) ..................3-17 Loading Continuous Forms (Rear Feed) ...................3-20 Unloading Continuous Forms ...................................3-20 Tearing Off Continuous Forms .................................3-21 FEEDING AND POSITIONING PAPER .........................3-23 Line Feed/Form Feed ...............................................3-23 Micro Feed ...............................................................3-23
   xvi  User's Manual Load Position Adjust ................................................ 3-23 TIPS ON PAPER HANDLING ....................................... 3-24 General Tips ............................................................ 3-24 Multipart Forms ........................................................ 3-24 Envelopes ................................................................ 3-24 Labels ...................................................................... 3-24 CHAPTER 4 PRINTING ................................................................................. 4-1 MULTIPART FORMS (HI IMPACT MODE) ..................... 4-1 PRINT MODE(HI SPEED MODE/QUIET MODE) ............ 4-2 STARTING OR STOPPING PRINTING ........................... 4-3 Starting Printing ......................................................... 4-3 Stopping Printing ....................................................... 4-3 Resuming from a Paper-Out ...................................... 4-3 Printing the remaining lines on a page ........................ 4-3 Continuing printing after supplying paper.................... 4-4 Resuming after an Area Over warning ........................ 4-4 REMOVING PRINTED PAGES ....................................... 4-5 Removing Single Sheets ............................................ 4-5 Removing Continuous Forms ..................................... 4-5 CLEARING THE PRINT BUFFER ................................... 4-5 SELECTING PRINT FEATURES .................................... 4-6 Using Commercial Software ....................................... 4-7 Using the Control Panel ............................................. 4-7 Selecting MENU1 or MENU2 ..................................... 4-8 CHAPTER 5 USING SETUP MODE .............................................................. 5-1 HOW TO USE THIS CHAPTER ...................................... 5-1 ENTERING SETUP MODE ............................................. 5-2 OVERVIEW OF SETUP MODE ...................................... 5-4 Setup Mode Example ................................................. 5-5 Points to Remember .................................................. 5-8 PRINTING A LIST OF SELECTED OPTIONS ................. 5-8 DECIDING WHICH OPTIONS TO CHANGE ................. 5-11 MENU1 AND MENU2 ITEMS AND OPTIONS ............... 5-13 Resetting MENU1 and MENU2 ................................ 5-28 CHANGING HARDWARE OPTIONS ............................ 5-28 CHANGING PRINT POSITION ADJUSTMENT OPTIONS ..................................................................... 5-34 CHANGING CONFIGURATION OPTIONS ................... 5-43 HEAD GAP ADJUSTMENT ITEMS AND OPTIONS ...... 5-56 EXITING AND SAVING................................................. 5-57 Procedure ................................................................ 5-57 RESETTING DEFAULTS .............................................. 5-58 Resetting Power-On Defaults ................................... 5-58 Resetting Factory Defaults ....................................... 5-58 Resetting Factory Defaults in MENU1 and MENU2 .. 5-58 USING THE DIAGNOSTIC FUNCTIONS ...................... 5-59 Printing the Self-Test ............................................... 5-59 Procedure ................................................................ 5-60 Printing Hex Dumps ................................................. 5-61 Procedure ................................................................ 5-61 Checking Vertical Print Alignment (V-ALMNT) .......... 5-63
  User's Manual    xvii Procedure ................................................................5-63 SETUP MODE REFERENCE ........................................5-65 DPL24C PLUS ORGANIZATION .............................5-66 Differences in IBM Proprinter XL24E Emulation ........5-69 Differences in Epson ESC/P2 Emulation ..................5-69 ONLINE SETUP MODE ................................................5-70 CHAPTER 6 MAINTENANCE ........................................................................ 6-1 CLEANING .................................................................... 6-1 Cleaning and Vacuuming the Printer ......................... 6-1 Cleaning the Platen ................................................... 6-2 REPLACING THE RIBBON ............................................ 6-3 OPENING AND CLOSING THE CONTROL PANEL ....... 6-6 REMOVING THE STACKER UNIT ................................. 6-6 MOUNTING THE STACKER UNIT ................................. 6-7 CHAPTER 7 TROUBLE-SHOOTING ............................................................ 7-1 SOLVING PROBLEMS .................................................. 7-1 Print Quality Problems............................................... 7-1 Paper Handling Problems ......................................... 7-5 Operating Problems .................................................. 7-7 Printer Failures.......................................................... 7-8 Alarm display function ............................................... 7-9 Responses to alarm occurrences .............................7-10 DIAGNOSTIC FUNCTIONS ..........................................7-10 GETTING HELP ...........................................................7-11 CHAPTER 8 INSTALLING OPTIONS ........................................................... 8-1 INSTALLING THE CUT SHEET FEEDER ...................... 8-3 Installing on the front side of the printer ..................... 8-4 Installing on the rear side of the printer ...................... 8-6 Removing the Cut Sheet Feeder ............................... 8-9 INSTALLING THE TRACTOR UNIT ..............................8-10 INSTALLING THE LARGE STACKER ...........................8-11 APPENDIX A SUPPLIES AND OPTIONS....................................................... A-1 SUPPLIES ..................................................................... A-1 OPTIONS ...................................................................... A-1 APPENDIX B PRINTER AND PAPER SPECIFICATIONS ............................. B-1 PHYSICAL SPECIFICATIONS ....................................... B-1 FUNCTIONAL SPECIFICATIONS .................................. B-2 PERFORMANCE SPECIFICATIONS ............................. B-5 PAPER SPECIFICATIONS ............................................ B-6 Print Area .................................................................. B-6 Paper Thickness ....................................................... B-8 APPENDIX C COMMAND SETS ..................................................................... C-1 FUJITSU DPL24C PLUS................................................ C-2 Bar Code Printing Control ....................................... C-14 IBM PROPRINTER XL24E EMULATION ..................... C-22 EPSON ESC/P2 EMULATION ..................................... C-28
   xviii  User's Manual APPENDIX D INTERFACE INFORMATION ................................................... D-1 PARALLEL INTERFACE ................................................ D-1 Compatible Mode ...................................................... D-2 Nibble Mode ............................................................. D-4 Data Transmission Timing......................................... D-6 SERIAL INTERFACE ..................................................... D-7 Serial  Options ........................................................... D-8 Cable  Wiring ............................................................. D-8 Serial Protocols....................................................... D-10 USB INTERFACE ........................................................ D-11 Cable ...................................................................... D-11 Specification ........................................................... D-11 LAN INTERFACE ........................................................ D-12 Cable ...................................................................... D-12 Specification ........................................................... D-12 APPENDIX E CHARACTER SETS ................................................................. E-1 CHARACTER SETS 1 AND 2  (DPL24C PLUS AND IBM XL24E EMULATION) ........... E-1 ITALIC AND GRAPHICS CHARACTER SETS  (ESC/P2 EMULATION) ................................................. E-2 NATIONAL CHARACTER SETS  (ALL EMULATIONS) ..................................................... E-4 NATIONAL CHARACTER SETS  (DPL24C PLUS AND IBM XL24E EMULATION) ......... E-14 NATIONAL CHARACTER SETS  (ESC/P2 EMULATION) ............................................... E-16 NATIONAL CHARACTER SETS AND SUPPORTED RESIDENT FONTS (ALL EMULATIONS)..................... E-20 APPENDIX F RESIDENT FONTS ................................................................... F-1 INDEX ...............................................................................................................  IN-1 FUJITSU OFFICES ............................................................................................... 1
  User's Manual  QR-1 Q QUICK REFERENCE QUICK REFERENCE Quick Reference is written for experienced users — users who are familiar with how the printer works, but who may need to refresh their memory occasionally. Only the printer’s normal (non-setup) mode is covered. For details on setup mode, see Chapter 5. Normal mode operation includes everyday operations, such as paper handling and font selection. The printer comes up in normal mode when turned on. To enter setup mode, press the SET UP  button  while the ONLINE indicator is off (not lit).        Control panel The table on the next page lists normal mode operations with online and offline conditions and gives the required user response. Operations are listed by functions.
QUICK REFERENCE    QR-2  User's Manual Printer Operations (Normal Mode) :  Operation can be performed when the printer is in this state. — :  Operation cannot be performed when the printer is in this state. N/A: Does not apply. Operation Online Offline Required Response Enter normal mode  N/A  N/A  Turn printer on.  (Press I on the power switch.) If STANDBY lamp lights, Press any buttons. Place printer offline   — Press ONLINE. Place printer online  —   Press ONLINE. Load paper    Press LOAD. Line feed (forward)    Press LF/FF within three seconds. Unload paper to park position (both front and rear-fed continuous forms)   Press LOAD. Form feed (forward)    Press and hold LF/FF until the operation starts. Eject single sheets    Press and hold LF/FF until the operation starts. Tear off forms (continuous forms only)   Press TEAR OFF. Tear off forms, then press any button to retract forms. Micro feed (backward)    Press MICRO. Micro feed (forward)    Press MICRO. Select a paper feed direction      Press FRONT DIR. Select a print mode      Press PRINT MODE. Set/reset high impact mode    Press HI IMPACT. Select a paper input source    Press PAPER PATH. Select a gap mode  —   Press AUTO GAP. Save adjusted load positions    Press ONLINE and LOAD. Select MENU1 or MENU2  —   Press PAPER PATH and HI IMPACT. Clear print buffer  —   Press HIIMPACT and PRINT MODE. Reset power-on defaults    Turn printer off, then on. Start/stop/resume printing    Start:  Send print command. Stop/resume:  Press ONLINE. Resume printing after paper  —   Press ONLINE.
QUICK REFERENCE   User's Manual  QR-3 Printer Operations (Normal Mode) (Cont.) :  Operation can be performed when the printer is in this state. — :  Operation cannot be performed when the printer is in this state. N/A: Does not apply. Operation Online Offline Required Response Enter setup mode  —   Press SETUP until the printer beeps.  Exit to normal mode Self-test printing   Start: Turn printer off.  Press LF/FF while turning printer on. Pause/resume:  Press LOAD. Exit:  Press ONLINE.
QUICK REFERENCE    QR-4  User's Manual
  User's Manual  1-1 1  CHAPTER 1  INTRODUCTION INTRODUCTION Congratulations on purchasing this printer. This printer is a compact, versatile, flat paper path printer that offers maximum compatibility with today’s software packages and personal computers. The 24-wire print head provides crisp, clear printing for business, office, and home environments. This printer is also easy to install and use. DL7400Pro dot matrix printer (136 columns) Key printer features, models and options are listed in the next two sections.  Software compatibility. This printer, which operates primarily with the Fujitsu DPL24C PLUS command set, is compatible with the IBM Proprinter XL24E command set and the Epson ESC/P2 command set.  Various character sets. As basic character sets, IBM PC character sets 1 and 2 are available for the Fujitsu DPL24C PLUS command set and the IBM Proprinter XL24E emulation, and the italic character set and graphics character sets 1 and 2 are available for the Epson ESC/P2 emulation. As national character sets, a total of 56 or 58 national character sets (depending on the emulation), including IBM PS/2 character sets, are available.  Multiple fonts. The printer has nineteen resident fonts:  Ten bit-map fonts — Courier 10, Pica 10, Prestige Elite 12, Boldface PS, OCR-B 10, OCR-A 10, Correspondence, Compressed, Draft, and High-speed Draft and nine outline fonts — Timeless, Nimbus Sans, and Courier, each in upright, italic, and bold.  High-speed printing. At 10 cpi, print speed ranges from 120 cps for letter quality to 600 cps for Super high draft quality. FEATURES
INTRODUCTION    1-2  User's Manual  Large print buffer. 128K bytes are available in total for storing input data and downloading fonts. A large input data buffer allows you to send files to the printer and return to work in your application. A large download buffer allows you to use custom fonts.  136-column print line. 136-column printers print in landscape mode using legal- or standard-size computer forms.  Simple switching of paper types. The ability to “park” continuous forms makes it easy to switch between continuous forms and single sheets from the control panel. This switching is possible even for an optional cut sheet feeder and second tractor.  Dual tractor feeding capability. The tractor unit is removable and can be converted to front-feed or rear-feed.  Multi-path of paper.  The printer has multiple paths to feed paper : For the continuous form front and rear tractor(second tractor is option), For cut sheet loading paper table (front), front CSF(option), rear CSF(option).Also for cut sheet ejecting front and rear is selectable(front eject paper require removing for next paper loading)  Tear off  function. Available at both the front and the rear of the printer. TEAR OFF  button on the control panel is used.  High copy capability  Up to eight sheets for front/rear continuous forms and cut sheets fed from front paper table.  Up to five sheets for CSF fed  Auto paper thickness control. Features as standard equipment.  Auto interface selection.  The printer automatically selects the interface proper to the occasion. (This  function can’t move at single interface models)  Paper skew detection. The printer detects a skew of paper that is manually fed from the paper table and automatically ejects it without printing.  Area-over print prevention. The printer senses and memorizes the left and right edges of paper when loading the paper. If receiving data beyond either edge, the printer ignores it to prevent breakage of wires of print head.  Left Margin adjustment. The printer senses and memorizes the left and right edges of paper when loading the paper. Printer adjusts the left margin according to paper left edge. This function allows you inaccurate paper setting. Would you use set-up mode to select this function.   Maintenance-free. The printer only requires periodic cleaning and changing of the ribbon cartridge.
INTRODUCTION   User's Manual  1-3  Power Supply type; 100-120V (M33334A)    220-240V  (M33334B)  Interface type;  Centronics parallel + USB interfaces    Centronics parallel + RS232C serial interface  Printer add-on options are listed below. For details, see Chapter 8.  Cut sheet feeder. The SF940 single-bin feeder is available as an option. Two cut sheet feeders can be installed in front of and behind the printer at the same time. A cut sheet feeder allows single cut sheets and multiple-part cut sheets to be fed automatically.  Tractor unit. A second tractor unit may be bought as an additional option if dual tractor feeding capability is required.  LAN card. A LAN card is available as a printer add-on option. A user installable function, the LAN card can be installed only on printer models with the Centronics parallel + USB interfaces. For details, see Chapter 8.                  OPTIONS of DL7400Pro dot matrix printer    MODELS OPTIONS SF940 single-bin feeder (front). Slot for LAN card is available.(Centronics parallel + USB interfaces MODEL) Replacing stacker with large stacker is required when SF940 is installed in rear side. SF940 single-bin feeder (rear). Tractor unit (rear)
INTRODUCTION    1-4  User's Manual  Small paper table. It is used in printing a short cut sheet.   Large stacker. The large stacker accommodates sheets output from the rear.  It is used in continuous printing with a cut sheet feeder.  Sound proof cover. The acoustic noise is reduced.                                OPTIONS of DL7400Pro dot matrix printer  Small paper table  Large stacker Sound proof cover
  User's Manual  2-1 2  CHAPTER 2  SETTING UP SETTING UP Your new printer is easy to install and set up.  This chapter tells you how to set up the printer and start printing right away. If this is your first printer, you should read the entire chapter before attempting to use the printer.  In this chapter, you will learn how to:   Unpack, assemble, and select a good location for the printer   Identify the printer’s major parts   Connect the power and interface cables   Test the printer before connecting it to your computer   Install the printer driver   Select an emulation and print a sample page using your software  If you have a problem while setting up the printer, review the section Solving Problems in Chapter 7. If the problem persists, contact your dealer.  This printer is suitable for most business, office, and home environments. To obtain peak performance from the printer, select a location that meets the following guidelines:    Place the printer on a sturdy, level surface.   Place the printer near a well-grounded AC power outlet.   Ensure easy access to the front and rear of the printer by leaving several inches of space around the printer. Do not block the air vents on the front, left, and right sides of the printer.   Do not place the printer in direct sunlight or near heaters.   Make sure that the room is well-ventilated and free from excessive dust.   Do not expose the printer to extremes of temperature and humidity. SELECTING A GOOD LOCATION
SETTING UP    2-2  User's Manual   Use only the power cord supplied with the printer or recommended by your dealer. Do not use an extension cord.   Do not plug the printer into a power outlet that is shared with heavy industrial equipment, such as motors, or appliances, or such as copiers or coffee makers. Such equipment often emits electrical noise or causes power degradation.  Unpack the printer as follows: 1.  Open the carton and remove the printer and its components. Make sure that you have all of the items shown below. Note that the power cord supplied depends on the printer model (100-120 V or 220-240 V).                     Checking items received UNPACKING THE PRINTER Power cord  Ribbon cartridge CD-ROM Quick Guide Printer
SETTING UP   User's Manual  2-3 2.  Carefully examine each item for damage. Report any problems to your dealer or shipping agent. 3.  Place the printer where you plan to use it. 4.  Remove the tapes and cushions securing the printer. Open the front cover and remove the shipping restraint cardboard that holds the print head carriage in place (shown below).           Removing the shipping restraint cardboard 5.  Store the original shipping carton and packaging materials for future use. For example, the original packaging is ideal for use when you move or ship your printer to another location. NOTE The interface cable is not included with the printer. You must purchase it separately. Connection of the interface cable is described later in this chapter.
SETTING UP    2-4  User's Manual Checking Options and Supplies The following options and supplies, if ordered, are shipped separately:   LAN card (option)   Cut sheet feeder (option)   Tractor unit (option)   Small Paper Table (option)   Large Stacker (option)   Sound proof cover  (option)   Extra monochrome ribbon cartridge Make sure that you received all the options you ordered. Installation of options is described in Chapter 8. Once you are sure you have everything, you are ready to assemble the printer.
SETTING UP   User's Manual  2-5 This section explains how to handle the paper table, change the tractor unit position and install the ribbon cartridge.  Handling the paper table You must open or close the paper table when you operate the front tractor.  1  Open the paper table. Slightly raise the front end of the paper table (1), then pull (2) and lift the table (3).              ASSEMBLING THE PRINTER
SETTING UP    2-6  User's Manual  2 Close the paper table. Lower the paper table as shown in the figure below (1), then push (2) and close (3) the cover.  The complete setup conditions are shown below.  Make sure that the top end of the paper table is engaged with the printer guide pin and the guide pin on the paper table is inserted into the cover groove.                  NOTE Do not apply unreasonable force while you are handling the paper table.  It could cause damage.  Also, do not leave the paper table in incomplete setting.  Running the printer with the paper table left in incomplete conditions could cause a paper jam.  Cover groove.  Paper table guide pin Guide pin (metal stud) (3)(1)(2)(2)(1)(3)
SETTING UP   User's Manual  2-7 Installing the Ribbon cartridge (HOT) CAUTION <HOT> The print head and metal frame is hot during printing or immediately after printing.  Do not touch them until it cools down.  1.  Prepare the printer to install the ribbon cartridge. Make sure that the print head protecting cardboard used for transportation has been removed, then turn on the printer power with the top cover closed.  Ensure that the print head moves and stops at the ribbon replacement position.  NOTE If you turn on the printer power with the top cover open, the print head does not move.  Turn the printer power with the top cover closed.  2.  Turn off the printer power. Make sure that the power switch is set to the “” side. 3.  Open the front cover of the printer. Slide the print head carriage so that its center is at the position for replacing the ribbon cartridge (indicated by the triangle marking on the front of the upper cover).         Preparing the printer to install the ribbon cartridge NOTE The buzzer may sound if the print head is moved while the power supply is ON.
SETTING UP    2-8  User's Manual 4.  Remove the ribbon cartridge from its package.  Turn the ribbon feed knob clockwise to be sure that it feeds properly.       Preparing the ribbon cartridge 5.  Locate the two ribbon release levers on either side of the ribbon cartridge. Each ribbon release lever has a mounting pin on the side. Place the mounting pins on the ribbon support bracket of the print head cartridge. Insert the ribbon so that the ribbon falls between the nose of the print head and the print guide.              Installing the ribbon cartridge   6.  Press the ribbon release levers inward until the mounting pins snap into the holes of the ribbon support brackets. Gently pull on the cartridge to be sure that the pins are secure in the holes. Ribbon feed knob Turn clockwise to tighten Ribbon release lever Mounting pin
SETTING UP   User's Manual  2-9 7.  Turn the ribbon feed knob clockwise to take up any slack in the ribbon. 8.  Close the front cover.  NOTE A Fujitsu ribbon cartridge is recommended. Don’t use other cartridges.  If other cartridges are used, operating problems or a damage of the print head may be caused.  Selecting the tractor unit Position  NOTE This printer uses a detachable tractor that can be used on either the front or back of the printer.  You can attach the tractor to either the front or back of the printer according to your installation or operating conditions.  The printer is delivered to you with the tractor attached to the front.  You can detach it from the front and then attach it to the back if needed.  See “SELECTING PAPER PATH” in Chapter 3.
SETTING UP    2-10  User's Manual Mounting and removing the tractor unit Tractor unit at the front [Removing the tractor unit] Raise the paper table.  While pressing the lock levers of the tractor frames located on both sides of the tractor unit, lift out the tractor unit to remove it.           [Mounting the tractor unit] 1)  Position the U-shaped slots on both sides of the tractor unit over the guide pins of the printer unit.  (To set the tractor unit in position, line it up with the groove of the left guide pin.  The right guide pin has no groove). 2)  Push down the shaft at the front of the tractor unit until it locks with an audible click.  (Do not press the lock levers when pushing down the shaft.)       Lock lever Lock lever  Paper table Guide pin Guide pin U-shaped slotU-shaped slotTractor unit
SETTING UP   User's Manual  2-11 3)  Verify that the hooks on both sides of the tractor unit are securely hooked onto guide pin 2 as shown in the following figure.  Tractor unit at the rear  [Removing the tractor unit] While pressing the lock levers of the tractor frames located on both sides of the tractor unit, lift out the tractor unit to remove it.
SETTING UP    2-12  User's Manual [Mounting the tractor unit] 1)  Position the U-shaped slots on both sides of the tractor unit over the guide pins of the printer unit.  (To set the tractor unit in position, line it up with the groove of the left guide pin.  The right guide pin has no groove). 2)  Push down the shaft at the front of the tractor unit until it locks with an audible click.  (Do not press the lock levers when pushing down the shaft.)  3)  Verify that the hooks on both sides of the tractor unit are securely hooked onto guide pin 2 as shown in the following figure.
SETTING UP   User's Manual  2-13 Now that your printer is assembled, take a moment to become familiar with its major parts. Looking at the printer from the front right side and rear left side, you can see the parts of the printer shown in the figure below.                       Printer components The printer control panel has the buttons and indicators used to load and feed paper (see Chapter 3) and select print features (see Chapter 4). The control panel also allows you to change the printer’s optional settings (see Chapter 5). GETTING ACQUAINTED WITH YOUR PRINTER Print headPaper guidePower switchControl panel InterfaceconnectorSub guide Paper tableTractor unit Front CSF connector Front cover Rear stackerPower connectorRear CSF connector
SETTING UP    2-14  User's Manual The explanation of Symbols on the printer • Power Switch Turns the printer power ON (Printable Condition)/ OFF (Unprintable Condition).            ・ Print head The print head become extremely hot during printer operation and remain so immediately afterwards.  Do not touch these parts until sufficient time has passed to allow them to cool. Otherwise, burns or personal injury may result.             ON OFF
SETTING UP   User's Manual  2-15 ・ Spacing motor The spacing motor become extremely hot during printer operation and remain so immediately afterwards.  Do not touch these parts until sufficient time has passed to allow them to cool. Otherwise, burns or personal injury may result.
SETTING UP    2-16  User's Manual Before you plug in the printer:   Make sure that the printer power is switched off. The side marked “” on the power switch should be depressed.   Make sure that the power outlet is properly grounded.   Make sure that you use the power cord shipped with the printer.   To plug in the power cord: 1.  Plug one end of the power cord into the power connector on the rear of the printer. 2.  Plug the other end of the power cord into the power outlet.  Connecting the power cord 3.  Make sure that the power cord is securely connected. 4.  Turn on the power by pressing the side marked “I” on the power switch. The POWER indicator on the printer control panel will light, the print head will move to its home position within a few seconds, and the ONLINE indicator will light (green). NOTE If no forms are loaded, the printer beeps and the PAPER OUT indicator lights and the ONLINE indicator will not light.  CONNECTING THE POWER CORD
SETTING UP   User's Manual  2-17 At this point, load paper and run the printer self-test. The self-test checks printer performance and print quality before you connect the printer to the computer. Use either single sheets or continuous forms (see Chapter 3). This section describes the self-test procedure using single sheets. Loading Paper for the Self-Test To print the self-test, use paper wider than 215.9 mm (8.5 inches) and set the left paper guide all the way to the right to avoid clipping the test pattern. Standard letter or A4 size paper can be used lengthwise (portrait mode).  Pull the sub guide out as required to accommodate the paper size. Before loading paper, make sure that the printer is on. Then, proceed as follows: 1. Press the PAPER PATH button on the control panel to select the cut sheet mode (the CUT SHEET indicator  lights).                Loading a sheet of paper 2.  Insert a sheet of paper (A4 or larger) into the printer, keeping it aligned with the paper guide on the left hand side of the paper table. The sheet will automatically be pulled into the printing start position. TESTING THE PRINTER (OFFLINE)  PAPER PATH
SETTING UP    2-18  User's Manual Printing the Self-Test The printer has a built-in self-test program. The self-test prints the firmware version, the names of the printer’s resident emulations, and all of the characters available in the emulations. The self-test prints 80 characters per line. To print a self-test page, make sure that a sheet of paper is loaded. Then proceed as follows:  1.  Turn the printer off. 2.  While pressing the LF/FF button, turn the printer back on. Keep the LF/FF button pressed until the printer beeps. Self-test printing will start.      Starting the self-test 3. Allow printing to continue for a dozen or more lines of repeat printing. To exit the self-test mode, press the ONLINE button. Then press the LOAD button to remove the test page. 4.  Examine the self-test page. It should look like the sample on the next page. Check that printing is uniform and that there are no light, dark, or smudged areas. If the print quality is good, go to step 5. Otherwise, try to correct the problem as follows:   Make sure that the ribbon is installed correctly.   Load a new sheet of paper.   Repeat the self-test procedure.
SETTING UP   User's Manual  2-19   Sample self-test page 5.  To exit the self-test mode, press the ONLINE button. The printer will return online. NOTE The printer can also print a special “demo pattern” that illustrates some of the printer’s capabilities. To print the demo pattern:  1.  Load a sheet of paper (A4 or larger). 2.  Turn the printer off . 3.  While pressing the PRINT MODE  button, turn the printer back on.   The printer will start printing the demo pattern. 4.  The demo pattern stops printing after one page. To pause or restart the demo during printing of a page, press the ONLINE button. 5.  To exit demo mode, turn the printer off.   ver.  x.xxver.  x.xx ver.  x.xx 00000-0000 (00x) 000000
SETTING UP    2-20  User's Manual                       Demo pattern
SETTING UP   User's Manual  2-21 Your printer supports one of the following interface options:   Centronics parallel interface+RS-232C serial interface   Centronics parallel interface + USB (+LAN) interface The parallel interface connector has wire clips. The serial interface connector has tapped holes. Cables for these interfaces are available from dealers, cable manufacturers, and other suppliers. The LAN card is a user installable option. For details, see Chapter 8  For detailed interface specifications, see Appendix D. Selecting a Parallel Interface Cable For the parallel interface, use a cable that meets the following specifications:   At the printer end, use a shielded male Centronics connector, such as an Amphenol DDK 57FE-30360 or its equivalent. To prevent RFI (radio frequency interference), the connector cover must be connected to the cable shield.   At the computer end, most computers (including IBM PCs) require a male DB-25P connector. Some computers, however, require a Centronics connector. To determine the type of connector your computer uses, refer to your computer user manual.   Make sure that the cable length does not exceed 3 meters (10 feet). Selecting a Serial Interface Cable For the serial interface, use a cable that meets the following specifications:   At the printer end, use a 25-pin male connector, such as a Cannon DB-25P or its equivalent.   To determine the type of connector your computer requires, refer to your computer user manual or ask your dealer.   The cable length can be up to 15 meters (50 feet). This type of length is required in many networking and shared-printer configurations. CONNECTING THE PRINTER TO YOUR COMPUTER
SETTING UP    2-22  User's Manual Selecting a USB Cable   When the USB interface is used to connect to the host computer, the parallel interface and the serial interface (factory add-on option) cannot be connected simultaneously.   The USB interface does not guarantee all connections of USB-supported devices. Selecting a LAN cable   When the LAN cable is connected, the parallel and USB cables cannot be used.   The LAN cable, when used in 100BASE-TX environments, must conform to category 5 or higher. Connecting the Interface Cable To connect the interface cable: 1.  Turn off both the printer and the computer. 2.  Attach the interface cable to the connector. Do not connect more than one interface cable type to the printer at the same time.   Connecting the interface cable
SETTING UP   User's Manual  2-23 NOTE The LAN interface is a user add-on option. When installing a LAN card, remove the two screws securing the cover and remove the cover. Then insert the LAN card and reattach the cover with the two screws removed earlier. For details, see Chapter 8.  3.  To secure a parallel interface cable, flip the fastener clips located on the printer into the notches on the cable connector. To secure a serial interface cable, tighten the screws in the cable connector. 4.  Attach the other end of the interface cable to your computer.  Gently pull on the cable to verify that it is secure.  Before printing with your software, verify that the correct emulation is selected on your printer. This section describes the available emulations and their selection. For Experienced Users: The printer’s factory default  factory setting is the Fujitsu DPL24C PLUS emulation. If this emulation is acceptable, you may skip this section. An emulation is a set of commands used by your software to communicate with the printer. There are many different emulations available for printers. Each emulation has unique features and capabilities. This printer offers three resident emulations:   Fujitsu DPL24C PLUS (for Fujitsu DL-series printers)   IBM Proprinter XL24E  Epson ESC/P2 Resident emulations are stored in the printer’s permanent memory.  Here are some points to help you determine which emulation to select:   Determine which emulations your software supports. (Refer to your software documentation.) Since most software programs support this printer, try to run a program with the factory default emulation first. (DPL24C PLUS emulation is the factory default.) Try this emulation even if you are not sure of which emulation to choose. See Chapter 5 for detailed information about how your printer communicates with your software. SELECTING AN EMULATION
SETTING UP    2-24  User's Manual   If you are using more than one software package, determine which emulation is supported by the software you use most frequently. Select that emulation.   If your software supports more than one emulation, select the DPL24C PLUS emulation if possible. This emulation has the greatest capabilities.   If you want to use an emulation that is not supported by your software, contact your software manufacturer or printer dealer and ask whether support is available. You may be able to obtain a printer driver that is not shipped with the original software package. To select an emulation, proceed as follows: 1.  Turn the printer on and load a sheet of paper. To change a single printer setting, such as the emulation, you can use a single sheet paper. To change several printer settings as described in Chapter 5, you must load continuous forms paper. See Chapter 3 for paper loading instructions. 2.  Enter setup mode. Press the ONLINE button to place the printer offline. Then, press the SETUP button until the printer beeps. As the printer enters offline setup mode, it prints the following information:
SETTING UP   User's Manual  2-25     Initial printout in setup mode Check that the <<FUNCTION>> menu is printed at the bottom of the page. <<FUNCTION>> menuFunction
SETTING UP    2-26  User's Manual 3.  Select the MENU1 function. Locate the cursor on left edge of the aluminum print guide. Initially, this cursor should be positioned at SAVE & END at the beginning of the <<FUNCTION>> menu. Press the LOAD button repeatedly to position the cursor at MENU1, as shown below:    Press the  MICRO FEED button to select MENU1 and print the following <EMULATE> options:  <EMULATE>      DPL24C+    XL24E    ESC/P2  The currently selected emulation is indicated by a short underline. In the figure shown above, the Fujitsu DPL24C PLUS emulation is selected. 4.  Select an emulation. Press the LOAD button repeatedly to position the cursor at the required emulation. Press the  MICRO FEED button to select the emulation and print the next MENU1 item. 5. Exit MENU1. Press the ONLINE button to exit the MENU1 function and reprint the <<FUNCTION>> menu. 6.  Exit setup mode to save the emulation. To exit setup mode and save the new emulation, make sure that the cursor is positioned under SAVE & END. Then press the  MICRO FEED button. The printer selects SAVE & END and then goes online. To change other printer settings using the printer setup mode, see Chapter 5.
SETTING UP   User's Manual  2-27 Once the self-test verifies that the printer is functioning correctly, try printing using one of your software packages. This exercise will ensure that the printer is correctly connected to your computer. If you are using a parallel interface, the printer usually prints the correct characters automatically. However, you may need to adjust the page layout or various print features using your software or the printer setup mode. If you are using a serial interface, the printer may not work at all or it may print a lot of “?” characters. In this case, the serial settings on the printer do not match those of your computer or your software. Before changing any settings, use the procedure described below to try printing using the printer’s preselected factory settings. Test communication between the printer and computer as follows: 1.  Load a sheet of paper. 2.  Check that the printer is online. If the ONLINE indicator is not green, press the ONLINE button. 3.  Try to print using your word processor, a programming language, or other software. 4.  Use your software printer selection menus or the printer setup mode (described in Chapter 5) to make required changes in the page layout or other print features. If the printer does not print or prints the wrong characters, proceed as follows:   Make sure that the interface cable is properly connected.   Make sure that the printer emulation selected in your software is the same as that selected on the printer.   If you are using a serial interface, make sure that the printer serial interface settings are the same as those on the computer. The printer’s factory default settings are 8 data bits, no parity, 1 stop bit, 9600 baud, and XON/XOFF protocol.  You can change the serial settings on either the printer or your computer. To change the printer settings, see Chapter 5. To change the computer settings, use the selection menus provided by your software or the commands of your computer operating system. The following example uses the MS-DOS operating system:   PRINTING A SAMPLE PAGE (ONLINE)
SETTING UP    2-28  User's Manual  Using MS-DOS to Specify Serial Interface Settings For an IBM PC or compatible device, use the following MS-DOS MODE commands to set the computer serial settings to match the printer factory default settings:  MODE COM1:9600,N,8,1,P MODE LPT1:=COM1  To activate these settings whenever you turn the computer on, write the MODE commands in your AUTOEXEC.BAT file. Make sure that the MODE.COM file is included in your root directory.   If the printer still doesn’t work, consult your dealer or someone experienced in serial interface communications.   If an error occurs during printing with Windows, simply printing the page again will cause the printed characters to be garbled. To avoid this problem, execute reset from the control panel or turn off the printer, then print the page again.  You are now finished setting up and testing the printer. To familiarize yourself with everyday printer operations, such as loading paper, selecting print features, and printing, see Chapters 3 and 4.  A printer driver is required for using the printer in a Windows environment.  Special printer drivers are provided with the DL7400Pro printer. For information about how to install printer drivers, refer to INSTALLGUIDE_(LANG).PDF or Readme.txt of the printer driver to be installed. -  These printer drivers run with DLP24C+ emulation. Be sure to specify DLP24C+ emulation for the printer mode. -  The DL7400Pro printer driver is a printer driver for monochrome printing. The color data printing result may differ from its print preview or the monochrome data printing result.  INSTALLING THE PRINTER DRIVER
  User's Manual  3-1 3 CHAPTER 3  PAPER HANDLING PAPER HANDLING This chapter explains how your printer uses paper. Topics covered are:  Selecting paper   Overview of paper operations   Adjusting for paper thickness   Using single sheets   Using continuous forms (front-tractor feed and rear-tractor feed)   Feeding and positioning paper   Switching paper types Tips for paper handling are given at the end of this chapter. Check that section if you are using multipart forms, envelopes, or labels.  The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. For best results, use paper that meets the specifications listed below.  (See Appendix B for detailed specifications.) If you are unsure of the suitability of a particular paper, try testing the paper or consult your dealer. Length  Single sheets: 70 to 420 mm (3 to 16.5 in) Continuous forms: 102 mm (4 in) or greater Width  Single sheets: 55 to 420 mm (2.16 to 16.5 in) Continuous forms: 102 to 420 mm (4 to 16.5 in) Thickness  0.57 mm (0.022 in) maximum total thickness. Copies  1 to 8-copies (Paper table/Front/Rear tractor) 1 to 5-copies (Cut sheet feeder) Note: To use cut sheets exceeding 297 mm in length, the optional arge stacker are required.  SELECTING PAPER
PAPER HANDLING    3-2  User's Manual The following buttons are used in paper handling:   LF/FF, TEAR OFF, PAPER PATH,  MICRO FEED,  MICRO FEED and LOAD buttons on the control panel  The following figure shows the location of each button:        Location of the buttons Table 3.1 summarizes the use of buttons in paper handling. More detailed information is provided later in this chapter.  NOTE To load or feed paper, the printer must be:   Online but not receiving or printing data   Offline but not in setup mode To micro feed paper, the printer must be:   Online but not receiving or printing data   Offline but not in setup mode  OVERVIEW OF PAPER OPERATIONS
PAPER HANDLING   User's Manual  3-3 Table 3.1  Buttons Used for Paper Handling  Button/Dial Purpose  Action ONLINE Change the printer mode  Stop/resume printing Press ONLINE to place the printer online or offline.Press ONLINE to stop or resume printing. LOAD Load/unload paper   Save adjusted load point Press LOAD to load paper or to retract continuous forms to the “park position.” Press LOAD and ONLINE simultaneously to permanently store a load position adjusted by micro feeding immediately after loading paper. LF/FF Form feed   Line feed Press and hold LF/FF to execute a form feed. Continuous forms are fed forward by one page. Single sheets are ejected. Press LF/FF within three seconds to feed paper forward by one line. TEAR OFF  Advance forms for tear off  Press TEAR OFF to advance the forms perforation to the tear off  edge. Tear off the forms, then press any button to retract the remaining forms. PAPER PATH Selects paper path Press PAPER PATH to select the paper path: front tractor, rear tractor, cut sheet. HI IMPACT  Set/reset HI IMPACT mode Press HI IMPACT to set or reset hi impact mode.
PAPER HANDLING    3-4  User's Manual Table 3.1  Buttons Used for Paper Handling (Cont.)  Button/Dial Purpose  Action FRONT DIR/AUTO GAP  Select cut sheet ejectionPress FRONT DIR/AUTO GAP at Online to select a direction of ejecting cut sheet.  Front ejection –  FRONT indicator lights. It blinks when paper is ejected to the paper table prompting the user to remove the paper.  Rear ejection –  FRONT indicator does not light. When you save your setting in the setup mode, it becomes the new default. The default setting is invoked whenever you turn on the printer.  MICRO  Micro Feed  Press MICRO/MICRO to feed paper by 1/180 inch in the direction of the arrow.  MICRO FRONT DIR/AUTO GAP Select paper thickness control mode Select paper thickness control mode. AUTO GAP — AUTO GAP indicator lights. Manual Gap — AUTO GAP indicator doesn't lights. The Manual Gap dial is enabled. MANUAL GAP DIAL Select paper  Thickness at MANUAL MODE Select the paper thickness at MANUAL MODE. Auto Gap is usually used.  Auto Gap is used for printing on paper of different thicknesses.
PAPER HANDLING   User's Manual  3-5 This printer has a variety of paper paths and feed directions. Paper Paths and Feed Directions See the following five cases.    : Cut sheet     : Continuous forms   (n) : Input   [n] : Output With front tractor   (1) Front tractor  Print  Rear eject        With rear tractor  (2) Rear tractor Print  Front eject   SELECTING PAPER PATH (2)Rear tractor(1) (2)(1)  (3)  (3) [1] (1)  Front tractor
PAPER HANDLING    3-6  User's Manual With front and rear tractors (either optional) (1) Front tractor  Print  Rear eject (2)  Rear tractor    Print  Front eject (3)  Paper table    Print  Paper table (4)  Paper table   Print  Rear stacker       Rear tractor (2)  [4] [3]  (3) (4) Front tractor (1)  [2]  [1]
PAPER HANDLING   User's Manual  3-7 In the next two cases, the number of cut sheets stacked in the printer may be reduced depending on printing conditions and environments.  Follow the notes. With rear tractor and front optional cut sheet feeder and large stacker(optional).  (1) Rear tractor    Print  Front eject (2)  Paper table                     Print  Paper table  (3) Paper table   Print  Rear stacker (4)  Front cut sheet feeder   Print  Paper table (5)  Front cut sheet feeder   Print  Rear stacker With front or rear tractor and rear optional cut sheet feeder and large stacker. In addition, the front and rear tractor (either is optional) can be mounted. (1) Front tractor   Print  Rear eject (2) Rear tractor   Print  Front eject (3) Paper table   Print  Paper table (4) Paper table   Print  Rear stacker (7)  Rear cut sheet feeder   Print  Paper table (8)  Rear cut sheet feeder   Print  Rear stacker   (4) (5)(2)(3) [3] [5] [1] (1)Rear tractor Front cut sheet  feeder [2] [4] Rear cut sheet feeder Large stocker(2) (1)  [1] [2] Rear tractor(3)(4)  [4][8] (7)(8)  Front tractor[3] [7]
PAPER HANDLING    3-8  User's Manual With rear tractor and front and rear optional cut sheet feeder and large stacker.  In addition, the front and rear tractor (either is optional) can be mounted. (2) Rear tractor   Print  Front eject (3) Paper table   Print  Paper table  (4) Paper table   Print  Rear stacker  (5)  Front cut sheet feeder  Print  Paper table (6)  Front cut sheet feeder  Print  Rear stacker (7)  Rear cut sheet feeder   Print  Paper table (8)  Rear cut sheet feeder   Print  Rear stacker          NOTES When remaining the ejected cut sheet on the paper table, the REMOVE PAPER indicator blinks and the printer stops printing.  Before restarting printing, be sure to remove the cut sheet. You must remove cut sheets one by one immediately after ejection. This is required therefore the printer may load an ejected sheet again or an ejected sheet may push the previous sheets out of the printer.  To eject sheets larger than A4 size onto the paper table, the paper table must be replaced with the optional large cut sheet table to prevent ejected sheets from falling off the paper table. When printing thin paper, multipart copy paper, or large size paper, frequently remove the paper from the rear stacker or the paper table.  Rear cut sheet  feeder Large stocker(2)(5) (6)[2] Rear tractor(3)(4)  [4] [6] [8] (7)(8)  Front cut sheet  feederr [3] [5] [7]
PAPER HANDLING   User's Manual  3-9 The printer can handle paper of different thicknesses, including multipart forms with up to eight parts (original plus seven copies). For details on paper thickness specifications, see Appendix B. The printer automatically adjusts for different paper thicknesses. You can use the MANUAL GAP DIAL to adjust the paper thickness manually at manual mode.          Adjusting the manual gap dial Table 3.2  Manual Gap Dial Settings Number of Copies  (Including the Original) *1  Setting *2 1 copy   1 2 copies   2 3 copies   3 4 copies   4 5 copies   5 6 copies   6 7 copies   7 8 copies   8 Envelopes  A Slips  B, C, D Ribbon replacement  R *1  For carbon-interleaved paper, the carbon counts as one copy. *2  Vary the setting up or down (including A to R) to optimize printing especially for labels and envelopes. Select R when replacing a ribbon or clearing a paper jam. NOTE If printing is messy, the ribbon miss-feeds, or the paper jams, move the manual gap dial  one setting higher. ADJUSTING FOR PAPER THICKNESS
PAPER HANDLING    3-10  User's Manual  This section describes how to load paper from the paper table or cut sheet feeder. The paper table allows paper to be loaded manually, one sheet at a time. A cut sheet feeder allows paper to be loaded automatically from the paper bin. Loading a Single Sheet of Paper To load a sheet of paper from the paper table: 1.  Make sure that the printer is turned on. 2.  Press the PAPER PATH button to select CUT SHEET (the indicator lights). 3.  Press the FRONT DIR button to select the direction of ejecting single sheets.   Front ejection — FRONTDIR indicator lights.   Rear ejection — FRONTDIR indicator doesn’t light. USING SINGLE SHEETS
PAPER HANDLING   User's Manual  3-11 4.  Adjust the left margin. On the left hand side of the paper table, a scale graduated in units of 1 [mm]. When the paper guide is positioned at scale 0 [mm], the left margin is 5 mm (0.2 inch).  Push the lock lever down to secure the guide. 5.  Pull the sub-guide out as required to the paper size.  NOTE When using the paper whose width is under 100 mm (4 inch), position the paper guide at scale 0 [mm].          Preparing to load a sheet of paper 6.  Insert a sheet of paper into the paper table. Make sure that the front edge of the paper engages snugly with the feed roller. NOTE If paper skews when it is loaded, the printer does not print and ejects the paper. (This function can be disabled by a setting in setup mode.) 0
PAPER HANDLING    3-12  User's Manual 7.  Press the LOAD button. The paper will advance to the top-of-form position. The top-of-form position is the first line on which printing can start. To adjust the position of the paper slightly, press the  MICRO FEED button or the  MICRO FEED button. The paper will move forward or backward in 1/180-inch increments. After loading paper, the printer goes into online mode.       Loading a sheet of paper 8.  Print a sample page and check the page margins. Make the following adjustments, as necessary:   Horizontal alignment. Readjust the paper guide if required.   Top-of-form setting (see Chapter 5).   Margin settings. Use your software or the printer setup mode (see Chapter 5).  NOTE Do not open the front cover during printing. With the cover open detection option installed, the printer never prints while the front cover is open. Close the front cover to perform printing.  LOAD
PAPER HANDLING   User's Manual  3-13 Loading Paper from the Cut Sheet Feeder (Option) A cut sheet feeder (SF940) allows automatic printing on single sheets without the need to manually insert the sheets one-by-one. This can save you a lot of time when printing long files using single sheets. See Chapter 8 for more information on the cut sheet feeder. For installation of the feeder, refer to its user’s manual. When a feeder is mounted and the feeder cable is connected, the printer automatically knows the feeder type and controls the feeder accordingly. 1.  Two steps of extension are available for supporting long sheets of paper.  Steps of extension 2.  Adjust the left margin. To help align the left paper guide, use the inch-based ruler located behind the paper guides. The ruler is graduated in 10 columns per inch. For example, setting the left paper guide 12.7 mm (0.5 inch) from the left gives a left margin of 6.3 mm (0.25 inch) plus the left margin specified by your software or the printer setup mode.
PAPER HANDLING    3-14  User's Manual   Slide the right paper guide until the distance between the two guides is the approximate width of your paper. 3.  Manually fan the stack of paper and place it in the paper bin.  NOTE A short horizontal mark inside the left paper guide indicates the maximum capacity of the bin. Make sure that your paper stack does not exceed this horizontal mark.  Loading the cut sheet feeder (Front feed)  Loading the cut sheet feeder (Rear feed) 4.  Readjust the right paper guide, leaving a slight gap between the paper guide and the right edge of the paper. Slide the guide to the approximate width of the paper, or the paper will not be loaded properly. Pull the right locking lever forward. 5.  Push the bin lever down to the “SET” position. 6.  Load paper to the top-of-form position using either of the following methods:
PAPER HANDLING   User's Manual  3-15   Load the paper manually. Press the LOAD button. The paper will advance to the top-of-form position. Adjust the position of the paper as needed by the MICRO button or the MICRO button (micro feed).   Load the paper using your software. Press the ONLINE button to place the printer online. Load paper according to the instructions in your software documentation. Most software packages load paper automatically. After loading paper, the printer goes into online mode. 7.  Print a sample page and check the page margins. Make the following adjustments, as necessary:   Horizontal alignment. Readjust the paper guides if required.   Top-of-form setting (see Chapter 5).   Margin settings. Use your software or the printer setup mode (see Chapter 5).  NOTE Do not open the front cover during printing. Ejecting Single Sheets If you print using software, each sheet is ejected automatically when the end of the printed page is reached. To manually eject sheets of paper, use the following method:   Press and hold down the LF/FF button to execute a forward form feed.   Continuous forms paper, fan-folded at the horizontal perforations, is ideal for printing rough drafts and long files. The paper is fed into the printer using the forms tractors.  USING CONTINUOUS FORMS
PAPER HANDLING    3-16  User's Manual Positioning the Paper Stack Place the stack of continuous forms paper directly below the rear of the printer or below the front of the printer. After the paper is installed in the printer, the paper path should look like this:  Good placement  Bad placement  Placement of continuous forms
PAPER HANDLING   User's Manual  3-17 Loading Continuous Forms (Front Feed) This section explains how to use continuous forms as the tractor unit is installed at the front of the printer. The tractor unit pushes continuous forms. This condition applies when you first purchase the printer. Up to 8-ply media can be fed by the front tractor unit. You can use continuous forms paper even if you have a cut sheet feeder installed at the rear of the printer. To load continuous forms paper: 1.  Make sure that the printer is turned on. Remove any single-sheet paper from the printer. 2.  Lift up the paper table as shown below. 3.  Release the tractor locking levers by pulling them up. Open the tractor paper holders. See the following figure. 4.  Position the left tractor. Push the left locking lever down to secure the tractor. Center the middle forms support.               Positioning the tractors 5.  Adjust the left margin. Below the left tractor, there is a tractor guide, short inch-based ruler graduated in 10 columns per inch. Use the ruler to help position the tractor. When the paper edge is positioned to the zero line, the left margin is 12 mm (0.5 inch) including perforation area and the arrow indicates the location of the first character. Locking Lever Locking LeverCenter Guide
PAPER HANDLING    3-18  User's Manual 6.  Fit the paper feed holes onto the left and right tractor pins.  Adjust the right tractor to the width of the form. Close the paper holders.  Adjusting paper tension 7.  Pull the right tractor to stretch the paper taut. Push the right locking lever down to secure the tractor in place. 8.  Lower the paper table to the down position (normal mode).   Lowering the cut sheet stand CAUTION  Before lowering the paper table, make sure that the paper holders are closed. If the holders are opened, they may cause damage to the tractors and the paper table.  Make sure that the paper table is positioned to its normal mode. If it is not done, jamming may occur when continuous forms paper is fed.  Paper Holders Paper table
PAPER HANDLING   User's Manual  3-19 9.  Press the PAPER PATH button to select “FRONT TRACTOR”. (The indicator lights.) 10.  Press the LOAD button to advance the paper to the top-of-form position. Top-of-form is the first line on which printing can start. After loading paper, the printer goes into online mode. 11.  Print a sample page and check the page margins. Make the following adjustments, as necessary:   Horizontal alignment. Move the forms tractors as required.   Top-of-form setting (see Chapter 5).   Margin settings. Use your software or the printer setup mode (see Chapter 5).  NOTE Do not open the front cover during printing.
PAPER HANDLING    3-20  User's Manual Loading Continuous Forms (Rear Feed) A tractor is supplied as standard and is attached to the front of the printer. It can be attached to the rear of the printer. You can also buy a tractor unit as an additional rear tractor unit. A maximum of 8-ply media can be fed from the rear tractor unit.   Put the paper table in the normal mode when the rear tractor unit is to be used. For reinstalling the tractor unit for rear feed, see page 2-11 to 2-12 . 1.  Press the PAPER PATH button to select REAR TRACTOR (the indicator lights). 2.  Set the continuous forms. Go to step 3-8 in the section Loading Continuous Forms (Front Feed) in this chapter. 3.  Load the continuous forms. Go to step 9 in the section Loading Continuous Forms (Front Feed) in this chapter. Unloading Continuous Forms To unload continuous forms: 1.  Make sure that the FRONT TRACTOR or REAR TRACTOR indicator lights. 2.  Press the LOAD button. The continuous forms paper is retracted to the park position. If the paper cannot be retracted in one operation, continue to press the LOAD button until the paper is parked.  NOTE The printer can retract continuous forms paper up to a maximum of 55.8 cm (22 inches) per operation.  3.  To remove the paper, raise the tractor paper holders and lift out the paper.  NOTE If continuous forms are unloaded without stopping, the paper may slip off the tractors.
PAPER HANDLING   User's Manual  3-21 Tearing Off Continuous Forms Your printer has a special “tear off edge” that allows you to tear off printed pages without wasting paper. The tear-off edge is located on the front and rear of the printer. To tear off continuous forms using the tear off  edge: 1.  Press the TEAR OFF button. The bottom perforation of the last page advances to the tear off  edge. If you specified TEAR OFF: AUTO using the HARDWARE function in setup mode, the paper automatically advances to the tear off  edge at the end of each job (or when the printer has printed all the data received).  NOTE If the bottom perforation of your paper is not positioned at the tear off  edge, the length of your paper may not be specified correctly in your software or the printer setup mode. Check that the paper length is specified correctly. For information on specifying page length using setup mode, see Chapter 5.
PAPER HANDLING    3-22  User's Manual 2.  Tear the paper off at the perforation.  Tearing off continuous forms (front feed)  Tearing off continuous forms (rear feed) 3.  Press any button to retract the forms back to the top-of-form position.
PAPER HANDLING   User's Manual  3-23 The following functions are available whether the printer is online or offline. Line Feed/Form Feed Use the line feed/form feed function to move paper forward.   Pressing and holding down the LF/FF button feeds one sheet of paper.   Pressing the LF/FF button once advances the paper one line (do not hold the button more than three seconds). Micro Feed Use the micro feed function to fine tune the position of the paper.  Press the  MICRO button to feed paper backward by 1/180 inch.  Press the  MICRO button to feed paper forward by 1/180 inch.  Remember that the top-of-form will differ from the original setting. Load Position Adjust Use also the micro feed function to adjust the load position of the paper.  When the  MICRO button or the  MICRO button is used immediately after the LOAD button is pressed, the adjusted position of paper is retained as the new load position until the power is turned off.   Pressing the ONLINE and LOAD buttons simultaneously saves the new position permanently. The load position can be set for single sheets and continuous forms respectively.      Adjusting Load Position by Using Window of Card Guide  The lines of window on the right side of card guide indicate printing line. So use this as a guide to adjust load position.  FEEDING AND POSITIONING PAPER WindowCard Guide
PAPER HANDLING    3-24  User's Manual General Tips   Use high-quality paper. Do not use paper that is wrinkled or curled at the edges.   Do not use paper with staples or metal parts.   Do not use paper with unpredictable variations in thickness, such as paper with partial multilayers, paper with embossed printing, and labels with the backing sheet exposed.   Store paper in a clean, dry environment. Multipart Forms   Avoid using carbon-interleaved single sheets if possible. Printing tends to become misaligned on the bottom sheet.   To ensure smoother feeding of paper-stapled, multipart forms, raise the rear stacker to support the forms. Envelopes When printing envelopes, use the paper table or the manual feed slot of the cut sheet feeder. Note the following:   When loading envelopes, make sure that the envelope flaps face forward. Otherwise, the envelopes may jam in the printer. Labels   Be careful to check operating conditions when using labels. Labels are sensitive to temperature and humidity.   Only use labels mounted on continuous forms backing sheets. Do not print labels mounted on single sheet backing. Labels mounted on single sheet backing tend to slip and printing becomes crooked.   Do not feed labels backwards using the LOAD button from the control panel. Jamming may occur.   Do not use the printer tear-off feature when printing labels. If the labels are retracted, the backing may peel off and the labels may jam in the printer.   Test-print labels before running a job. If jams occur, go into setup mode and -  set the paper thickness control to manual mode and -  set the paper thickness indicator to a wider position manually. If jamming problems continue, try a different type of label.   TIPS ON PAPER HANDLING
  User's Manual  4-1 4 CHAPTER 4  PRINTING PRINTING This chapter describes the following everyday  printing operations:   Using multipart form (hi impact mode)   Selecting the print mode   Starting, stopping, or resuming printing   Removing printed pages   Clearing the print buffer   Selecting the print features  Instructions for loading paper are given in Chapter 3. This printer has enough capability to print multipart forms.  When superior copy capability is required, use the HI IMPACT  mode.  Press the HI IMPACT button on the printer control panel. This function is valid when the HI IMPACT indicator lights.        Print control panel NOTE  Setting HI IMPACT mode by pressing the HI IMPACT button is cancelled when you turn off the printer.  If you wish to have the HI IMPACT mode set on power-on, save the setting in setup mode. MULTIPART FORMS (HI IMPACT MODE)
PRINTING    4-2  User's Manual It has three print modes in this printer. ・STANDARD MODE ・HI SPEED MODE Horizontally consecutive dots are omitted (LQ), and the printer stpeed is twice as STANDARD MODE ・QUIET MODE The consecutive dots are omitted (LQ). The print speed is slowed to LQ speed (except for LQ). Skipping the space (no characters) at higher speed doesn’t work. To select Print mode:    1.    If the PRINT MODE button is pressed at STANDARD MODE (Both HI SPEED indicator light and QUIET indicator light are turned off), it becomes HI SPEED MODE. At this time, the HI SPEED indicator lights. 2.    If the PRINT MODE button is pressed at HI SPEED MODE, HI SPEED MODE is released, and it becomes QUIET MODE. At this time, the QUIET indicator lights. 3.    If the PRINT MODE button is pressed at QUIET MODE, the QUIET mode is released , and it becomes STANDARD MODE.         Print control panel NOTE  HI SPEED MODE is valid only for LQ.  QUIET MODE and HI SPEED set by pressing the PRINT MODE button are cancelled when you turn off the printer.  If you wish to have the QUIET MODE or HI SPEED set on power-on, save the setting in setup mode.    PRINT MODE(HI SPEED MODE/QUIET MODE)
PRINTING   User's Manual  4-3 Starting Printing Before you start to print, make sure that paper is loaded. To start printing, press the ONLINE button to place the printer online. Then start your software. Stopping Printing To stop printing immediately, press the ONLINE button to place the printer offline. You can also use your software to stop printing, but there will be a slight delay before printing stops. Any data sent to the print buffer but not yet printed is stored until you resume printing. Data in the print buffer is lost if you turn the printer off. To resume printing, press the ONLINE button again. To cancel printing, use the cancel commands provided by your software or computer. To clear the print buffer, place the printer offline and press the PRINT MODE and HIIMPACT buttons. Any data sent to the print buffer before you canceled printing will be lost. Resuming from a Paper-Out The printer can “sense” when paper runs out. Depending upon how PPR-OUT (paper-out) is set in setup mode, the printer either:   Stops printing and lights the red PAPER OUT indicator, or   Continues printing until no more data remains in the printer. See Chapter 5 for details on setting PPR-OUT. The factory default is to stop printing if continuous forms paper runs out and to continue printing if single sheet paper runs out. To resume printing when paper runs out, use either of the methods described below: Printing the remaining lines on a page This method is convenient to continue printing under the paper-out condition, but is not available when the cut sheet feeder is used. 1.  Press the ONLINE button. The printer returns to online mode, prints or feeds one line, and the PAPER OUT indicator lights up again. 2.  Repeat this procedure until the full page is printed. Line spacing , however, may be uneven. STARTING OR STOPPING PRINTING
PRINTING    4-4  User's Manual CAUTION When printing remaining lines, be careful not to print on the platen. Printing on the platen may damage both the platen and the print head. Continuing printing after supplying paper 1.  Install paper on the forms tractors or on the cut sheet stand, or in the cut sheet feeder bin, as described in Chapter 3. 2.  To load the first sheet of paper, press the LOAD button. The PAPER OUT indicator will turn off. 3.  Press the ONLINE button to place the printer online. The printer resumes printing.  NOTE For continuous forms paper, the page where printing stopped and the page where printing resumes may be incorrectly printed. In this case, wait for the entire job to finish printing. Then reprint the incorrect pages. Resuming after an Area Over warning The printer senses the left and right edges of paper and stores their positions when the paper is loaded. If your software will print data past either edge, the printer ignores that data but does not stop printing.  The AREA OVER detection control functions when AREACNT (area control) is set to ENABLE in setup mode. See Chapter 5 for information on setting AREACNT. The factory default is not to sense the edges. If paper is dark-colored or preprinted, the printer may not be able to sense the edges correctly.  In this case, disable the sensor.
PRINTING   User's Manual  4-5 This section describes the best methods for removing single sheets or continuous forms paper after printing. Removing Single Sheets When you print using software, the printer automatically ejects each sheet of paper when the end of the printed page is reached. To eject sheets manually, use one of the following methods:   Press and hold down the LF/FF button to execute a form feed. Removing Continuous Forms To avoid wasting paper, use the printer tear-off function to remove continuous forms paper. Press the TEAR OFF button to advance the perforation to the tear-off edge. Tear the paper off, and then press any button to retract the paper back to the top-of-form position. See Chapter 3 for more detailed instructions. Place the printer offline. Press the PRINT MODE and HI IMPACT buttons simultaneously to clear all data from the print buffer. This method is useful when you cancel a print operation and do not want to continue printing data already sent to the printer. This method does not change or clear MENU1 and MENU2 settings, paper loading position settings, and downloaded fonts.  REMOVING PRINTED PAGES CLEARING THE PRINT BUFFER
PRINTING    4-6  User's Manual The print features you select determine how your printed pages will look. Print features include the following:  Print quality  Fonts   Pitch (characters per horizontal inch)   Page length and width   Line spacing (lines per vertical inch) To select print features, you can use either commercial software or the printer control panel. The method you use depends on the capabilities of your software. If your software has most of the features you require, you may rarely – if ever – have to use the control panel. In fact, your software often overrides the printer settings. If your software has limited options, you can use the printer control panel to select print features. Sometimes, the control panel enables you to select features not available through your software. For example, you can select downloaded fonts not supported by your software.   SELECTING PRINT FEATURES
PRINTING   User's Manual  4-7 Using Commercial Software Many commercial software packages offer a wide variety of print features, including some features that are not supported by this printer. For example, software often provides a wider range of font sizes than the printer can accommodate. Software also allows you to specify multiple fonts on a page. To determine which features your software supports and how to select them, refer to your software documentation.  Using the Control Panel Use the PAPER PATH and HI IMPACT button to directly select one of the two menus.         Printer control panel The SETUP button specify MENU1 or MENU2, either of which allows you to specify different sets of options in advance. Some of the print features include emulation, print quality, character pitch, and line spacing.  When you first turn the printer on, the MENU 1 indicator is lit; that is, all of the print features assigned to MENU1 are enabled. However, you can easily switch to MENU2 before printing. You can also select a resident font other than the fonts assigned to MENU1 and MENU2.  NOTE For easy reference, keep a list of your current MENU 1 and MENU 2 settings near the printer. To print a list of current settings, see the section Printing a List of Selected Options in Chapter 5. You may also want to use the space provided in Table 4.1 to record your settings.
PRINTING    4-8  User's Manual Selecting MENU1 or MENU2 When you first turn the printer on, MENU1 is selected. To change to MENU2 or back to MENU1, proceed as follows: 1.  Press the ONLINE button to place the printer offline. 2.  Repeatedly press the PAPER PATH and  HI IMPACT buttons. The lighted indicator (1 or 2) shows the menu selected. When the menu selection is changed, the font (font, pitch, and quality) assigned in the selected menu becomes valid.          3.  Press the ONLINE button to return online. You are ready to print using the selected menu.
PRINTING   User's Manual  4-9 Table 4.1  MENU1 and MENU2 Settings Setting  Default Settings For easy reference, check () or record your default settings in the space below. Print Feature  MENU1  MENU2 Emulation Fujitsu DPL24C PLUS IBM Proprinter XL24E Epson ESC/P2   Font Courier 10 Prestige Elite 12 Compressed 17 Boldface PS Pica 10 Correspondence OCR-B 10 OCR-A 10 Courier Normal 10 (outline) Courier Bold 10 (outline) Courier Italic 10 (outline) Nimbus Sans Normal PS (outline) Nimbus Sans Bold PS (outline) Nimbus Sans Italic PS (outline) Timeless Normal PS (outline) Timeless Bold PS (outline) Timeless Italic PS (outline) Downloaded font 0 Downloaded font 1   Print quality Letter Report Draft High-speed draft Super high-speed draft   Pitch 2.5, 3, 5, 6, 10, 12 15, 17, 18 or 20 cpi Proportional spacing   Other features:
  User's Manual  5-1 5 CHAPTER 5  USING SETUP MODE USING SETUP MODE Your printer has two modes: normal and setup. Normal mode is used for everyday printer operations and is explained in Chapters 3 and 4. Setup mode serves two purposes. It enables you to:   Select the printer’s optional settings   Help diagnose printer problems These setup mode functions can be done either offline, using the printer control panel (offline setup), or remotely, using a setup program in your computer system or software (online setup).  Primarily, this chapter explains how to use the offline setup mode.  The online setup mode, which is reviewed briefly at the end of this chapter, is valid in all emulations. Optional settings on the printer include the emulation, fonts, pitch, page length and page width, serial interface options, and the top of form  setting. When you save your settings in the printer’s permanent memory, they become the new settings or defaults. These defaults are invoked whenever you turn on the printer. For example, if you save DPL24C PLUS as the default emulation, DPL24C PLUS is invoked when you turn on the printer. The printer diagnostic functions are SELF-TST, HEX-DUMP, and V-ALMNT. These functions are helpful for printer trouble-shooting, as described in Chapter 7.  The sections in this chapter are presented in logical sequence. If you are a first-time user, be sure to read the following sections first:   Entering Setup Mode   Overview of Setup Mode These sections will familiarize you with how setup mode works.  Once you understand the basics, use the following sections to select printer options that are compatible with your computer system’s hardware and software setup:   Printing a List of Selected Options   Deciding Which Options to Change   MENU1 and MENU2 Items and Options   Hardware Items and Options   Print Position Adjustment Items and Options   Configuration Items and Options HOW TO USE THIS CHAPTER
USING SETUP MODE    5-2  User's Manual   Head Gap Adjustment Items and Options   Exiting and Saving To restore the printer default settings (factory defaults or power-on defaults), see the section Resetting Defaults later in this chapter. For information on using the SELF-TST, HEX-DUMP, and V-ALMNT functions, see the section Using the Diagnostic Functions later in this chapter. For Experienced Users: Once you are familiar with setup mode, you may want to use the flowchart at the end of this chapter for quick reference. The flowchart lists all printer setup functions, items, and options.  Before entering setup mode, load continuous forms paper from the front tractor into the printer as described in Chapter 3. Several sheets of paper may be required to make all of your setup mode selections. To enter setup mode, follow these steps: 1.  Make sure that front continuous forms paper is loaded and press the PAPER PATH button to select the appropriate paper path. If continuous forms paper is fed from the rear or a CSF is mounted, the printer does not enter SETUP mode. 2.  Press the ONLINE button to place the printer offline. 3.  Press the SETUP button until the printer beeps.         Entering setup mode If you do not hear a beep or an alarm beep (beeps four times), you are not in setup mode. Place the printer offline and try again. ENTERING SETUP MODE
USING SETUP MODE   User's Manual  5-3 4.  When the printer enters offline setup mode, it prints the following information.  Initial printout in setup mode The initial printout contains a header, help menu, and <<FUNCTION>> menu. The header tells you that the printer is offline and in setup mode. The help menu provides a quick summary of how to use setup mode. The <<FUNCTION>> menu lists all of the functions available to you in setup mode. Note that the cursor on the left edge of the aluminum print guide is initially positioned at the SAVE & END function. Setup mode can also be entered by turning off the printer, then turning the printer back on while pressing the SETUP button until the printer beeps.
USING SETUP MODE    5-4  User's Manual When you enter setup mode, the following <<FUNCTION>> menu is printed:  << FUNCTION >> SAVE&END MENU1    MENU2    HARDWRE  ADJUST   CONFIG   GAP-ADJ  DEFAULT  LIST     SELF-TST   HEX-DUMP V-ALMNT  INITIAL  Table 5.1 summarizes the purpose of each function. Table 5.1  Setup Mode Functions Function Purpose SAVE & END  Exits setup mode and saves any changes made while in setup mode. MENU1 and MENU2 Assigns print features to MENU1 and MENU2 on the printer control panel. HARDWRE  Changes the printer hardware options. ADJUST  Changes the print position adjustment options. CONFIG  Changes the configuration options. GAP-ADJ  Adjust the gap between the print head and printing paper. DEFAULT  Resets factory defaults in MENU1 and MENU2. INITIAL  Resets factory defaults in MENU1, MENU2, HARDWRE, ADJUST, CONFIG, GAP-ADJ. LIST  Prints a list of all currently selected options. SELF-TST  Runs the self-test. HEX-DUMP Prints hex dumps. V-ALMNT  Checks and corrects vertical print alignment.  To select a function from the <<FUNCTION>> menu: 1.  Repeatedly press the “TEAR OFF” or “LOAD” button to position the cursor on the left edge of the aluminum print guide at the function you require. 2. Press the  button or the  button to select the function. If the function has items and options, the printer prints the first item and its options. The MENU1, MENU2, HARDWRE, ADJUST, CONFIG, and GAP-ADJ functions contain items that have selectable options. The other functions have neither items nor options. OVERVIEW OF SETUP MODE
USING SETUP MODE   User's Manual  5-5 The first three MENU1 items and their options are shown below. Items are enclosed in single brackets < >. < EMULATE>DPL24C+   XL24E   ESC/P2  <FONT    > COUR 10  PRSTG12  COMPRSD  BOLDFCE  PICA 10  CORRESP  OCR-B    OCR-A    COUR-N    COUR-BCOUR-I   N.SAN-N  N.SAN-B  N.SAN-I  TIMLS-N  TIMLS-B  TIMLS-I  DOWNLD0  DOWNLD1  <QUALITY>LETTER   REPORT   DRAFT    HI-DRFT  SH-DRFT To select an option from the <item> menu: 1.  Repeatedly press the “TEAR OFF” or “LOAD” button to position the cursor on the left edge of the aluminum print guide at the option you require. 2. Press the  button to select the option. The printer prints the next item and its options. You can press  to select the option.  Then, the printer prints the previous item and its options. 3.  After selecting the desired options, press the ONLINE button to reprint the <<FUNCTION>> menu. For each item, the short-underlined option is the current default option (the option currently saved in the printer’s permanent memory). In the previous example, the default options are Fujitsu DPL24C PLUS emulation, Courier 10 font, and letter print quality. The chart on the next page summarizes how to select options such as emulation, font, and print quality and how to use functions that do not have options. Setup Mode Example To become familiar with setup mode, try the following example. This example shows how to change the font and pitch in MENU2 to Prestige Elite 12 and 12 cpi. 1.  Load continuous forms paper. 2.  Enter setup mode. Press the SETUP button until the printer beeps. 3.  Select the MENU2 function. Wait for the printer to stop printing and press the “TEAR OFF” or “LOAD” button twice to position the cursor on the left edge of the aluminum print guide at MENU2. Press the “” button or the “” button to select the MENU2 function and print the <EMULATE> item and its options.
USING SETUP MODE    5-6  User's Manual  Summary of setup mode Enter setup mode: Press SETUP button
USING SETUP MODE   User's Manual  5-7 4.  Select the current emulation. Since you do not want to change the emulation, press the “” button to select the current emulation and print the next item, <FONT> and its options. 5.  Change the font to Prestige Elite 12. Press the “TEAR OFF” or “LOAD” button once to position the cursor on the left edge of the aluminum print guide on PRSTG12. Press the “” button to select PRSTG12 and print the next item, <QUALITY>, and its options. 6.  Select the current print quality. Since you do not want to change the print quality, press the  button to select the current print quality and print the next item, <PITCH>, and its options. 7.  Change the pitch to 12 cpi and exit the MENU2 function. Press the “TEAR OFF” or “LOAD” button once to position the cursor on the left edge of the aluminum print guide on 12 CPI. Since you do not want to make any other changes in MENU2, press the ONLINE button to select 12 CPI and exit MENU2.  The <<FUNCTION>> menu is then reprinted. 8.  Exit setup mode, saving the new font and pitch. Since the cursor on the left edge of the aluminum print guide is on SAVE & END, press the  MICRO FEED button or the  MICRO FEED button to select SAVE & END. The printer saves Prestige Elite 12 and 12 cpi as the new power-on defaults in MENU2.  The printer then exits setup mode and returns online. These settings remain in effect until changed.
USING SETUP MODE    5-8  User's Manual Points to Remember   Whenever you enter setup mode, short help menus are printed at the top of the page. Help menus are also printed when you select the SELF-TST, HEX-DUMP, or V-ALMNT functions. Use help menus for quick reference while in setup mode.   When printing the items and options for each function, you can only print one item at a time. However, you can move either forward or backward in the item list. To move forward (print the next item), press the  button. To move backward (print the previous item), press the  button.   While in the <<FUNCTION>> menu or when selecting a function that contains items and selectable options, press the ONLINE button to reprint the <<FUNCTION>> menu.   A short underline under the first two letters of an option indicates that it is the current default setting. For example, 12 CPI indicates that 12 characters per inch is the default pitch. To change the default, select and save a new pitch setting.   While in setup mode, you can use the LIST function to print out a list of the currently selected options (see the next section for details).   To exit setup mode and permanently save your changes, select the SAVE & END function. For details, see the section Exiting and Saving later in this chapter. To exit setup mode without saving your changes, turn the printer off. Your previous power-on defaults are active when you turn the printer on again.  The LIST function prints a list of all the printer’s currently selected options. This function is useful for checking the printer settings when you first enter setup mode or just before you exit. To print a list of options, load continuous forms paper and then proceed as follows: 1.  Enter setup mode. Press the SETUP button until the printer beeps. Wait for the printer to stop printing and check that the following <<FUNCTION>> menu is printed:  << FUNCTION >> SAVE&END MENU1    MENU2    HARDWRE  ADJUST   CONFIG   GAP-ADJ  DEFAULT  LIST     SELF-TST   HEX-DUMP V-ALMNT  INITIAL PRINTING A LIST OF SELECTED OPTIONS
USING SETUP MODE   User's Manual  5-9 2.  Select the LIST function. Repeatedly press the “TEAR OFF” or “LOAD” button to position the cursor on the left edge of the aluminum print guide on LIST. Next press the  button or the  button to select the LIST function. The printer starts to print a list of the currently selected options. The preselected factory settings, also called factory defaults, are shown on the opposite page. When the printer finishes printing the list of options, it reprints the <<FUNCTION>> menu. 3.  Do either of the following:   Select another function, or   Exit setup mode, saving any changes you made.  For details about other functions, see the other sections in this chapter. To exit setup mode and save your changes, make sure that the cursor on the left edge of the aluminum print guide is positioned on SAVE & END, then press the  button or the  button.
USING SETUP MODE    5-10  User's Manual  *1  FORMAT to CD are not printed when PARALEL option is selected for INTRFCE. It is printed equipped with RS-232C. *2  TEAR-EN is printed when AUTO option is selected for TEAROFF. Printout of factory defaults using LIST Func. Item Option Func. Item OptionMENU1 EMULATE DPL24C+ MENU2 EMULATE DPL24C+MENU1 FONT COUR 10 MENU2 FONT COUR 10MENU1 QUALITY LETTER MENU2 QUALITY LETTERMENU1 PITCH 10 CPI MENU2 PITCH 10 CPIMENU1 LINE SP 6 LPI MENU2 LINE SP 6 LPIMENU1 CHAR-W NORMAL MENU2 CHAR-W NORMALMENU1 CHAR-H NORMAL MENU2 CHAR-H NORMALMENU1 ATTRIB NONE MENU2 ATTRIB NONEMENU1 PAGE LG 11.0 IN MENU2 PAGE LG 11.0 INMENU1 LFT-END 1  COLM MENU2 LFT-END 1  COLMMENU1 TOP-MRG 1  LINE MENU2 TOP-MRG 1  LINEMENU1 LANGUGE PAGE437 MENU2 LANGUGE PAGE437MENU1 CHR-SET SET2 MENU2 CHR-SET SET2MENU1 PRF-SKP NO-SKIP MENU2 PRF-SKP NO-SKIPMENU1 WIDTH 13.6 IN MENU2 WIDTH 13.6 INMENU1 ZEROFNT NO-SLSH MENU2 ZEROFNT NO-SLSHMENU1 DC3-CDE ENABLE MENU2 DC3-CDE ENABLEMENU1 CR-CODE CR ONLY MENU2 CR-CODE CR ONLYMENU1 LF-CODE LF & CR MENU2 LF-CODE LF & CRMENU1 RGHTEND WRAP MENU2 RGHTEND WRAPMENU1 INT-MEC DISABLE MENU2 INT-MEC DISABLEMENU1 ==END== MENU2 ==END==Func. Item Option Func. Item OptionHARDWRE PPR-OUT DETECT CONFIG TEAROFF MANUALHARDWRE PRT-DIR BI-DIR CONFIG TEARPOS VISIBLEHARDWRE BUZZER ON CONFIG TEAR-EN 1 SEC (*3)HARDWRE WORD-LG 8 BIT CONFIG CUTLOAD AUTOHARDWRE BUFFER  8KBYTE CONFIG LOADTIM 1.5 SEC (*4)HARDWRE SENLEVL 100% CONFIG DECODE DIRECTHARDWRE STANDBY 1MIN CONFIG FCNTARE ENABLE1HARDWRE INTRFCE AUTO-2S (*1) CONFIG RCNTARE ENABLE1HARDWRE FORMAT 8NONE 1 (*2) CONFIG CUT-ARE ENABLE1HARDWRE BAUD-RT 9600 (*2) CONFIG CUT-ONL ONLINEHARDWRE PROTOCL XON/XOF (*2) CONFIG CNT-ONL ONLINEHARDWRE DSR IGNORE (*2) CONFIG LOCK NONEHARDWRE DUPLEX FULL (*2) CONFIG //S// DISABLEHARDWRE CTS DETECT (*2) CONFIG FCNT-PE EDGEHARDWRE CD IGNORE (*2) CONFIG RCNT-PE EDGEHARDWRE ==END== CONFIG GATHER DISABLECONFIG CUT-CTL SPEEDCONFIG SKIP-PR ENABLECONFIG STATUS DISABLECONFIG BANDCTL DISABLEFunc. Item Option CONFIG TOF-CTL DRIVERCONFIG FCNT-SF DISABLEADJUST FCNTORG 1.8/6IN CONFIG RCNT-SF DISABLEADJUST FCNTFIN 0 /180 CONFIG CUT-SF DISABLEADJUST RCNTORG 1.8/6IN CONFIG CUTEDIR FRONTADJUST RCNTFIN 0 /180 CONFIG CSFEDIR REARADJUST FCUTORG 1.8/6IN CONFIG CUTEJCT AUTOADJUST FCUTFIN 0 /180 CONFIG FL-CENT POSN1ADJUST RCUROTG 1.8/6IN CONFIG RL-CENT POSN1ADJUST RCUTFIN 0 /180 CONFIG SKEWCNT PRCISINADJUST FCNTBTM 0 /180 CONFIG FF-CODE EJECTADJUST RCNTBTM 0 /180 CONFIG CSFBIN1 FRONTADJUST CUT-BTM 0 /180 CONFIG CNT-LD SPEEDADJUST CNT-LFT 0 /90 CONFIG CSF-LD NORMALADJUST CUT-LFT 0 /90 CONFIG CSFAPTC NORMALADJUST FCNTADJ 0 /360 CONFIG LF-CTL SPEEDADJUST RCNTADJ 0 /360 CONFIG PR-MODE NORMALADJUST FCNTAJL 0 /360 CONFIG HI-IMPT DISABLEADJUST RCNTAJL 0 /360 CONFIG DQ-MODE MODE2ADJUST CUT-ADJ 0 /360 CONFIG POW-POS NORMALADJUST FCSFADJ 0 /360 CONFIG ==END==ADJUST RCSFADJ 0 /360ADJUST FCNTLOR 4 /9ADJUST FCNTLFN 0 /90ADJUST RCNTLOR 4 /9ADJUST RCNTLFN 0 /90 Func. Item OptionADJUST CUTLOR 1.8/9ADJUST CUTLFN 0 /90 GAP-ADJ AMOUNT AUTOADJUST FCNTCUT 99 /180 GAP-ADJ ==END==ADJUST RCNTCUT 99 /180ADJUST CUT-CUT 20 /180ADJUST FRCSLNT 28/360ADJUST ==END==--------------------------------------------------<< Hardware settings >>---------------------------------------------------------------------------<< Adjust settings >>-------------------------*** Setup Parameters ***-------------------------<< Config settings >>--------------------------------------------------------------------------------------------------------------------------------<< Menu 1 settings >><< Menu 2 settings >>--------------------------------------------------------------------------------------------------------<< Gap Adjust settings >>----------------------------------------------------
USING SETUP MODE   User's Manual  5-11 The previous page shows a printout of the printer’s factory default settings. In this printout, options are listed by functional group:   Menu 1 settings (MENU1 function)   Menu 2 settings (MENU2 function)   Hardware settings (HARDWRE function)   Print position adjustment settings (ADJUST function)   Configuration settings (CONFIG function)   Print head gap adjustment settings (GAP-ADJ function) Most selectable options only alter print features, such as the typestyle, and page format. However, some options must be selected correctly for the printer to work properly with your hardware and software. For each function, Table 5.2 lists items whose options must be selected correctly for system and printer accessory compatibility. Table 5.2  Required Options Function Item  Option MENU1 EMULATE The emulation selected on the printer must be the same as the emulation selected in your software. If you selected an emulation when you set up the printer (Chapter 2), you do not need to change the EMULATE option unless you want to change to a different emulation. The emulation assigned to MENU1 is the default when you turn the printer on. See the section MENU1 and MENU2 Items and Options later in this chapter. MENU2 None  If you use MENU2, the emulation selected for MENU 2 must be the same as the emulation selected in your software. See the section MENU1 and MENU2 Items and Options later in this chapter.  DECIDING WHICH OPTIONS TO CHANGE
USING SETUP MODE    5-12  User's Manual Table 5.2  Required Options (Cont.) Function Item  Option HARDWRE  FORMAT BAUD-RT PROTOCL DSR DUPLEX CTS  CD If you have a serial interface, the serial interface options selected on the printer must be the same as the settings you selected using your software or your computer operating system. If the settings are not the same, the printer will not print or will print garbage. See the section HARDWRE Items and Options later in this chapter. ADJUST None  If you are not using software to specify the top margin of the page, use the printer’s default top-of-form setting, 1 inch (25.4 mm) from the top of the paper. If you are using software to specify the top margin of the page, change the default setting to 1/6 inch (4.2 mm). See the section Print Position Adjustment Items and Options later in this chapter. CONFIG None  You can change the printer’s primary configuration. See the section Configuration Items and Options later in this chapter. GAP-ADJ None  If you adjust the gap manually or fix the gap, change the setting.  See the section Print Head Gap Adjustment Items and Options.
USING SETUP MODE   User's Manual  5-13 The MENU1 and MENU2 functions allow you to change the print options assigned to MENU1 and MENU2 on the printer control panel.  In normal (non-setup) mode, you can easily switch between the menus for printing, as described in Chapter 4. MENU1 is invoked when you first turn the printer on. Select the same emulation on the printer as is selected in your software. If the emulations are not the same, the printer will not work correctly with your software. If you plan to use two different emulations on a regular basis, assign the most frequently used emulation to MENU1. Assign the second emulation to MENU2. All of the other settings available for MENU1 and MENU2 are optional.  Some of the items and options will vary with the emulation. To determine which features your software supports, refer to your software documentation. Table 5.3 describes the MENU1 and MENU2 items and options. Both functions offer the same items and options. The items in Table 5.3 are listed in the order in which they are printed. Not all items are defined for all emulations and some options vary with the emulation. The procedure for changing the options is referred to in the section Setup Mode Example.   MENU1 AND MENU2 ITEMS AND OPTIONS
USING SETUP MODE    5-14  User's Manual Table 5.3  MENU1 and MENU2 Items and Options NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items  Options Description <EMULATE>    Select the same emulation as is selected in your software. See the section Selecting an Emulation in Chapter 2 for information on selecting an emulation.  DPL24C+ Fujitsu DL-series printers  (DPL24C PLUS command set)  XL24E ESC/P2 IBM Proprinter XL24E printers Epson printers using the ESC/P2 command set NOTE: When you change the emulation, all MENU1 or MENU2 options are reset to the factory defaults for that emulation. <FONT>    COUR 10 PRSTG12 COMPRSDBOLDFCEPICA 10 CORRESPOCR-B OCR-A COUR-N COUR-B COUR-I N.SAN-N N.SAN-B N.SAN-I For each of the following fonts, the recommended pitch settings are given after the font name. When you change the font, be sure to also change the pitch, if required.
USING SETUP MODE   User's Manual  5-15 Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items Options Description <FONT> (continued) TIMLS-N TIMLS-B TIMLS-I     DOWNLD# Font 0 or font 1 in the printer’s download RAM See Appendix F for font examples. <QUALITY>    Select the print quality that most often meets your needs.  LETTER Letter print quality. This option provides the highest resolution but the slowest print speed. It cannot be used with the compressed font.   REPORT  Report print quality. This option provides lower resolution than letter quality, but at twice the speed. If you want only the double speed, regardless of fonts, use the correspondence font. The quality of the correspondence font is higher than that of report.   DRAFT  Regular draft print quality. This option provides lower resolution than report quality, but at 3 times letter speed.   HI-DRFT High-speed draft print quality. This option provides lower resolution than draft quality, but at 4.2 times letter speed.   SH-DRFT  Super high-speed draft print quality. This option provides lower resolution than hi-draft quality, but at 5 times letter speed . Condition: The margin is enough to speed up.
USING SETUP MODE    5-16  User's Manual Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items  Options Description <PITCH> ## CPI 2.5, 3, 5, 6, 10, 12, 15, 17, 18, or 20 cpi (characters per horizontal inch)  If 15cpi is selected at ESC/P2 emulation, font size is compressed and DQ and HDQ printing is done at LQ speed. To avoid speed down, select NOCMPRS at 15CPI item.   PROP SP  Proportional spacing (1/12 inch per character space) <LINE SP>  ## LPI  1, 2, 3, 4, 5, 6, 7, or 8 lpi  (lines per vertical inch) 6 lpi  3 lpi (double spacing) ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD ABCD <CHAR-W>    Change also the pitch 2 TIMES or 4 TIMES is selected.  NORMAL Standard character width    2 TIMES  Double character width   4 TIMES (*1) Quadruple character width
USING SETUP MODE   User's Manual  5-17 Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items Options Description <CHAR-H>    Change also the line spacing if 2 TIMES or 4 TIMES is selected.  NORMAL Standard character height    2 TIMES  Double character height   4 TIMES (*1) Quadruple character height  <ATTRIB>    Selects an attribute to add emphasis to your documents. Only one attribute may be selected at a time.  NONE   ITALICS    CONDNSD (*1)    SHADOW   BOLD
USING SETUP MODE    5-18  User's Manual Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table. MENU1 and MENU2 Items  Options Description <PAGE LG>    Specifies the length of the page in inches.     ## IN  For DPL24C PLUS and IBM XL24E emulations: 3.0, 3.5, 4.0, 5.0, 5.5, 6.0, 7.0, 8.0, 8.5, 11.0 (letter size), 11.6 (A4 size), 12.0, 14.0, 18.0 inches, or LINE For Epson ESC/P2 emulation: 4.0, 4.5, 5.0, ..., 11.0, 11.5, ..., 22.0 inches   LINE  Selecting the page length by specifying number of lines per page (default: 66 lines per page) Selecting this option displays the <PG LX10> and <PG LX1>. Use in combination the <PG LX10> to set the tens value of the lines-per-page setting, and the <PG LX1> to set the ones value of the lines-per-page setting. <PG LX10>  Tens value setting for setting number of lines per page 0 LINE, 10 LINE, 20 LINE, 30 LINE 40 LINE, 50 LINE, 60 LINE, 70 LINE 80 LINE, 90 LINE  The LINE setting depends on the line spacing setting 'LINE SP'.  When 0 LINE is set, the line spacing value is 11.0 IN (only when both 'PG LX10' = '0 LINE' and 'PG LX1' = '0 LINE' are set). <PG LX1>  Ones value setting for setting number of lines per page 0 LINE, 1 LINE, 2 LINE, 3 LINE 4 LINE, 5 LINE, 6 LINE, 7 LINE 8 LINE, 9 LINE  The LINE setting depends on the line spacing setting 'LINE SP'.  When 0 LINE is set, the line spacing value is 11.0 IN (only when both 'PG LX10' = '0 LINE' and 'PG LX1' = '0 LINE' are set).
USING SETUP MODE   User's Manual  5-19 Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items Options Description <LFT-END>   Specifies the print start column for changing the left margin. Printing starts at the position given by this column plus your software-specified left margin.   ## COLM  Column 1, 2, 3, ..., 41  <TOP-MRG>   Specifies the number of space lines for the top margin. The resultant blank space is the <TOP-MRG> setting minus 1 line. The total size of your top margin is the above resultant value plus the following two settings: top-of-form (default = 1 inch) and the software-specified top margin. If you are using software to specify the top margin, use the default (1 line) for <TOP-MRG>.   ## LINE  1, 2, 3,4, 5, 6, 7, 8, 9, or 10 lines
USING SETUP MODE    5-20  User's Manual Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items  Options Description <LANGUGE>    Selects a language. Appendix E shows the character sets for each language. Two-pass means that diacritical marks are printed separately from their letters and that letters are printed without any reduction. The first listing is common to all emulations. Options specific to each emulation are skipped. See the subsequent listings (*2) and(*3).  USA American English (Same as code page 437)  UK British English  GERMAN German  SWEDISH Swedish  PAGE437 Code page 437   PAGE850  Code page 850   PAGE860  Code page 860   PAGE863  Code page 863   PAGE865  Code page 865  ECMA94 ECMA 94  ISO8859 ISO 8859-1   PG852  Code page 852   PG852-T  Code page 852 two-pass   PG855  Code page 855   PG866  Code page 866  HUNGARY Hungarian  HUNG-T Hungarian two-pass
USING SETUP MODE   User's Manual  5-21 Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items Options Description <LANGUGE> (continued) SLOV Slovenian SLOV-T Slovenian two-pass  POLISH Polish  POLSH-T Polish two-pass  MAZOWIA Mazowian  MAZOW-T Mazowian two-pass  LATIN2 Latin 2  LATIN2-T Latin 2 two-pass  KAMENIC Kamenicky  KAMEN-T Kamenicky two-pass  TURKY Turkish  TURKY-T Turkish two-pass  CYRILIC Cyrillic  IBM437 IBM 437  IBM851 IBM 851  ELOT928 ELOT 928   PG-DHN  Code page DHN  LATIN-P Latin Polish  ISO-LTN ISO Latin  LITHUA1 Lithuanian1  LITHUA2 Lithuanian2  MIK   MACEDON Macedonian  PG-MAC   ELOT927
USING SETUP MODE    5-22  User's Manual Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items  Options Description <LANGUGE> (continued) ABG  ABY   DEC GR   HBR-OLD   PG862   HBR-DEC   GREEK 11   ISO-TUK ISO Turkish  RUSCII   LATIN-9   WCP1250 Windows-1250  WCP1251 Windows-1251  WCP1252 Windows-1252  (*2)   FRENCH French  ITALIAN Italian  SPANISH Spanish  DANISH1 Danish I  DANISH2 Danish II  FINNISH Finnish  NORWEGN Norwegian
USING SETUP MODE   User's Manual  5-23 Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items Options Description <LANGUGE> (continued)   DANISH1 Danish I  ITALIAN Italian  SPANSH1 Spanish I  SPANSH2 Spanish II  JAPAN Japanese  NORWEGN Norwegian   LATIN A  Latin American  FRENCH French  DANISH2 Danish II  KOREA Korea  LEGAL Legal <CHR-SET> (*2) SET 1  IBM character set 1  SET 2 IBM character set 2     If a downloaded (soft) font is used, the character set for that font overrides the <CHR-SET> setting.  (*3)   ITALIC Italic characters are available.   GRAPHIC  Graphics characters (ruled lines) are available.
USING SETUP MODE    5-24  User's Manual Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items  Options Description <AGM>  (*5) ON  Enables the graphic image command. OFF  Disables the graphic image command. <PRF-SKP>    For continuous forms, this option specifies whether an inch is skipped around the perforation. If you are not using software to specify a bottom margin, select SKIP when using thicker, multipart forms. SKIP  One inch is skipped around the perforation.  NO-SKIP The perforation is not skipped. Printing continues in the bottom margin of the page. <WIDTH> 13.6 IN  13.6-inch page width   11.4 IN  11.4-inch page width   11.0 IN  11-inch page width   8.0 IN  8-inch page width <ZEROFNT>    Specifies whether to print the number zero with a slash. This is useful to distinguish the capital letter “O” from the number “0”. Invalid for some soft fonts.  NO-SLSH 0  SLASH 0
USING SETUP MODE   User's Manual  5-25 Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items Options Description <DC3-CDE> (*4) ENABLE  Enables the DC1 and DC3 codes. Any data received between DC3 and the next DC1 is ignored. DISABLE  Disables the DC1 and DC3 codes. These codes are then ignored. <CR-CODE> CR ONLY No line feed is added to a carriage return.    CR & LF  A line feed is added to each carriage return. <LF-CODE> (*2) LF ONLY  No carriage return is added to a line feed.    LF & CR  A carriage return is added to each line feed. Note The default value of <LF-CODE> changes with the selected emulations as follows.  "LF&CR" is a default value in the DPL24C+ emulations.  "LF ONLY" is a default value in the XL24E emulations.
USING SETUP MODE    5-26  User's Manual Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items  Options Description <RGHTEND> WRAP  End-of-line wrap. Causes a carriage return plus a line feed.  OVR-PRT  Characters are overprinted at the end of a line.  <15CPI> (*3) COMPRES1 Enables compression of font when 15cpi selected at ESC/P2 emulation. Horizontal and vertical font size is compressed.  COMPRS2  Enables compression of font when 15cpi selected at ESC/P2 emulation. Horizontal font size is compressed.  NOCMPRS  Disables compression of font when 15cpi selected at ESC/P2 emulation.  When accept the compressing command, only horizontal compression is executed.
USING SETUP MODE   User's Manual  5-27 Table 5.3  MENU1 and MENU2 Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  Asterisks identify items and options that differ for the IBM XL24E and Epson ESC/P2 emulations. The notes are defined at the end of the table.  MENU1 and MENU2 Items Options Description <INT-MEC>  ENABLE  Mechanical initial is operated by receiving a reset command. DISABLE  Mechanical initial isn’t operated by receiving a reset command. <==END==>    Indicates the end of MENU1 items.  Press the  button to print the first item, <EMULATE>. Press the  button to print the previous item, <INT-MEC>. Press the ONLINE button to reprint the <<FUNCTION>> menu. *1  Unavailable in the IBM XL24E emulation *2  Unavailable in the Epson ESC/P2 emulations *3  Available only in the Epson ESC/P2 emulations *4  Available only in the DPL24C+ emulation *5  Available only in the IBM XL24E emulation
USING SETUP MODE    5-28  User's Manual Resetting MENU1 and MENU2 To reset the factory defaults for both MENU1 and MENU2, select the DEFAULT/INITIAL function.  For more information, see the section Resetting Defaults later in this chapter.  The DEFAULT function cannot reset those options which are handled by the HARDWRE, ADJUST, CONFIG, and GAP-ADJ functions. The INITIAL function can reset those options which are handled by the HARDWRE, ADJUST, CONFIG, and GAP-ADJ functions.  The HARDWRE function defines the printer’s hardware operating conditions.  If you are using the optional RS-232C serial interface, the serial interface options must be set properly for the printer to function correctly with your system hardware. Table 5.4 describes the HARDWRE items and options . Items are listed in the order in which they are printed. The procedure for changing the hardware options is described after Table 5.4. Table 5.4  HARDWRE Items and Options NOTE: Underlined options are the factory defaults.  HARDWRE Items  Options Description <PPR-OUT>    Specifies how the printer responds when you run out of paper.   CNTONLY The printer detects paper-out only for continuous forms. Printing stops and the PAPER OUT indicator lights red.  DETECT The printer detects paper-out for both continuous forms and single sheets. Printing stops and the PAPER OUT indicator lights red.     IGNORE  The printer ignores paper-out for both continuous forms and single sheets. Printing continues until no more data remains. No PAPER OUT warning is displayed.  CHANGING HARDWARE OPTIONS
USING SETUP MODE   User's Manual  5-29 Table 5.4  HARDWRE Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  HARDWRE Items  Options Description <PRT-DIR> BI-DIR  Bidirectional printing. The printer prints in either direction while seeking the next print direction for a shorter print time.   UNI-DIR  Unidirectional printing. Unidirectional printing is used for printing vertical lines in tables even if vertical alignment is not adjusted. Unidirectional printing is slower than bidirectional printing. <BUZZER>    Enables or disables the printer status buzzer.  ON Buzzer on (recommended). The printer beeps to indicate paperout or other conditions.  ON-1  Buzzer on (Sound in bass )  ON-2  Buzzer on (Sound in high-pitched tone)   OFF  Buzzer off under any conditions. <WORD-LG>    To determine the required word length, refer to your computer documentation. Select 8-BIT to print bit image graphics.  8 BIT 8-bit word length (used by most computers)   7 BIT  7-bit word length (MSB = 0)
USING SETUP MODE    5-30  User's Manual Table 5.4  HARDWRE Items and Options (Cont.) NOTE: Underlined options are the factory defaults. HARDWRE Items  Options Description <BUFFER>    Assigns buffer memory to input data and downloaded font data.   Print buffer  Download buffer  NONE 0 byte 128K bytes   256BYTE  256 bytes  127.75K bytes   2KBYTE  2K bytes  126K bytes  8KBYTE 8K bytes  120K bytes   24KBYTE  24K bytes  104K bytes   32KBYTE  32K bytes  96K bytes   96KBYTE  96K bytes  32K bytes   128KBYT  128K bytes  0K bytes   NOTE:  0BYTE option is recommended only for graphics application. With 128KB selected, the printer cannot accept any download font data. <SENLEVL> ## %  120, 110, 100, 90, 80, 70 or 60 % The threshold level of Photo Sensor for Paper Edge Detection. If output voltage of photo sensor is not enough, threshold level should be lower so that sensor can detect paper properly. In general reasons of low voltage of sensor output are as follows. ・Paper color is too dark. ・Preprint is on scanning area.  Note The margin for strong light from outside would be decreased, if you select threshold level lower than 100% (90,80,70 or 60%).
USING SETUP MODE   User's Manual  5-31  Table 5.4  HARDWRE Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  HARDWRE Items  Options Description <STANDBY>  ## MIN  1, 3, 5, 10, 20 or 30 MIN Time until shifting to the power saving mode is set. <INTRFCE>    Selects the type of the interface to the computer.   PARALEL  Centronics parallel interface   SERIAL  RS-232C serial interface  USB USB interface  AUTO-2S Auto interface selection mode  AUTO-4S AUTO-6S  Both interfaces are ready for communication.  AUTO10S AUTO15S  Specify the timing regarding the selected interface as being inactive.   AUTO20S  To switch the interface to the optional LAN interface, mount the LAN card with the setup mode set to “AUTO-XS” or “AUTOXXS” under “INTERFCE,” which in turn is under “HARDWRE” The interface will automatically switch to the optional LAN interface. To switch the interface to something other than the optional LAN interface, do either of the following:  To return the setup mode to “INTERFCE” under “HARDWRE,” remove the LAN card.  To switch the interface to a fixed interface, set PARALEL,USB with the LAN card mounted, and the setup mode set to “INTERFCE” under “HARDWRE.”
USING SETUP MODE    5-32  User's Manual Table 5.4  HARDWRE Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  HARDWRE Items  Options Description Serial Interface or USB interface Items. The following <FORMAT> to <DUPLEX> items are not printed when you select the PARALEL option for the <INTRFCE> item. Be sure that the options selected on the printer are the same as the options selected using your computer operating system or your software. Refer to the documentation provided for your computer and software. <FORMAT>   Number of data bits Parity bit Number of stop bits  8NONE 1 8 None  1  8NONE 2 8 None 2  8EVEN 1 8 Even 1  8ODD 1 8 Odd 1  7EVEN 1 7 Even 1  7ODD 1 7 Odd 1  7MARK 1 7 Mark 1  7SPACE 1 7 Space 1  7EVEN 2 7 Even 2  7ODD 2 7 Odd 2     The data format also includes a start bit. The mark is logical 1. The space is logical 0. <BAUD-RT> 150 300 600 1200 2400 4800 9600 19200 The baud rate is in bps (bits per second). Select the same baud rate as 600 used by your computer or modem.
USING SETUP MODE   User's Manual  5-33 Table 5.4  HARDWRE Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  HARDWRE Items  Options Description <PROTOCL>    Indicates data transmission protocol.  XON/XOF The DC1 and DC3 codes are used.   DTR  The Data Terminal Ready signal is used.   REV-CHL  The Reverse Channel signal is used. <DSR>  DETECT  DSR is detected by the printer.  IGNORE  DSR is ignored by the printer. <DUPLEX> FULL  Simultaneous data transmission occurs in opposite directions.   HALF  Data transmission occurs in either direction, but not simultaneously. <CTS> DETECT  CTS is detected by the printer.   IGNORE  CTS is ignored by the printer. <CD>  DETECT  CD is detected by the printer.  IGNORE  CD is ignored by the printer. <==END==>    Indicates the end of the HARDWRE item list. Press the  button to print the first item, which is <PPR-OUT>.  Press the  button to print the previous item. Press the ONLINE button to reprint the <<FUNCTION>> menu.
USING SETUP MODE    5-34  User's Manual When you print using ruled paper, you often want to adjust the print position so that the print sits properly on the ruled lines. The ADJUST function allows you to:  Set top-of-form position  Fine-tune top-of-form position  Fine-tune left print start column (left margin)  Adjust for accumulative line spacing error in a page The top edge of your paper is the physical top of the page. The logical top of the page, as “understood” by the printer when loading paper, is called the top-of-form. Printing starts at this position. Note that printing actually starts at the position obtained by adding the following:  Top-of-form, default = 1.8/6 inch (7.6mm)  Top margin specified by your software  Printer TOP-MRG (top margin setting), default = 1 line Table 5.5 describes the ADJUST items and options. Items are listed in the order they are printed. The procedure for changing top-of-form is described after Table 5.5.  CHANGING PRINT POSITION ADJUSTMENT OPTIONS
USING SETUP MODE   User's Manual  5-35 Table 5.5  ADJUST Items and Options NOTES:  Underlined options are the factory defaults.  When you select less than 1/6IN, please make sure that Print data from software has enough top margins so that no print data will not be printed out of paper.  HARDWRE Items  Options Description <FCNTORG> -1/6 IN 0/6 IN 1/6 IN 1.8/6 IN   : 6/6 IN   : 66/6 IN Sets the top-of-form for front continuous forms. The top-of-form is defined distance from top of paper to bottom of print line. The default is recommended if your top margin is not software-specified. <FCNTFIN>   0/180, ..., 29/180 Fine-tunes the top-of-form position for front continuous forms. Increases top-of-form in increments of 1/180 inch (0.14 mm). <RCNTORG> -1/6 IN 0/6 IN  1/6 IN 1.8/6 IN   : 6/6 IN   : 66/6 IN Sets the top-of-form for rear  continuous forms. The top-of-form is defined distance from top of paper to bottom of print line. The default is recommended if your top margin is not software-specified. <RCNTFIN>   0/180, ..., 29/180 Fine-tunes the top-of-form position for rear continuous forms. Increases top-of-form in increments of 1/180 inch (0.14 mm).
USING SETUP MODE    5-36  User's Manual Table 5.5  ADJUST Items and Options (Cont.) NOTES:  Underlined options are the factory defaults.  When you select less than 1/6IN, please make sure that Print data from software has enough top margins so that no print data will not be printed out of paper.  HARDWRE Items  Options Description <FCUTORG> -1/6 IN 0/6 IN  1/6 IN 1.8/6 IN   : 6/6 IN   : 66/6 IN Sets the top-of-form for front single sheets. The top-of-form is defined distance from top of paper to bottom of print line. The default is recommended if your top margin is not software-specified. <FCUTFIN>    0/180, ..., 29/180 Fine-tunes the top-of-form position for front single sheets. Increases top-of-form in increments of 1/180 inch (0.14 mm). <RCUTORG> -1/6 IN 0/6 IN 1/6 IN 1.8/6 IN   : 6/6 IN   : 66/6 IN Sets the top-of-form for rear single sheets. The top-of-form is defined distance from top of paper to bottom of print line. The default is recommended if your top margin is not software-specified. <RCUTFIN>    0/180, ..., 29/180 Fine-tunes the top-of-form position for rear single sheets. Increases top-of-form in increments of 1/180 inch (0.14 mm).
USING SETUP MODE   User's Manual  5-37 Table 5.5  ADJUST Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  ADJUST Items  Options Description <FCNTBTM>   -30/180, ..., 0/180,..., 30/180 It is possible to fine-tune the bottom blank by every 1/180 inches for its amount (4.2mm) of the front continuous form. NOTE: This setting is effective only at < FCNT-PE:EDGE >. <RCNTBTM>   -30/180, ..., 0/180,..., 30/180 It is possible to fine-tune the bottom blank by every 1/180 inches for its amount (4.2mm) of the back continuous form. NOTE: This setting is effective only at < FCNT-PE:EDGE >. <CUT-BTM>  -30/180, ..., 0/180,..., 30/180 It is possible to fine-tune the bottom blank by every 1/180 inches for its amount (4.2mm) of the cut sheet paper.
USING SETUP MODE    5-38  User's Manual Table 5.5  ADJUST Items and Options (Cont.) NOTE: Underlined options are the factory defaults. ADJUST Items  Options Description <CNT-LFT>   -10/90, ..., 0/90, ..., 10/90 Fine-tunes the left print start position for continuous forms. Moves the position left or right in increments of 1/90 inch  (0.28 mm).  NOTE: This setting is effective only at  < RCNT-SF: DISABLE > when the back tractor is used.  < FCNT-SF: DISABLE > when the front tractor is used.  <CUT-LFT>   -10/90, ..., 0/90, ..., 10/90 Fine-tunes the left print start position for single sheets. Moves the position left or right in increments of 1/90 inch  (0.28 mm).  NOTE: This setting is effective only at < CUT-SF:DISABLE >. <FCNTADJ>  -14/360, -9/360, -4/360, 0/360 4/360, 9/360, 14/360, GRAPHIC(*1) Compensates for the forms feed error accumulated through feeding of front continuous forms. <RCNTADJ>  -14/360, -9/360, -4/360, 0/360 4/360, 9/360, 14/360, GRAPHIC(*1) Compensates for the forms feed error accumulated through feeding of rear continuous forms. <FCNTAJL>  -14/360, -9/360, -4/360, 0/360 4/360, 9/360, 14/360, GRAPHIC(*1) Compensates for the forms feed error accumulated through feeding of front continuous forms. (Last page)
USING SETUP MODE   User's Manual  5-39 Table 5.5  ADJUST Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  ADJUST Items  Options Description <RCNTAJL>  -14/360, -9/360, -4/360, 0/360 4/360, 9/360, 14/360, GRAPHIC(*1) Compensates for the forms feed error accumulated through feeding of rear continuous forms.  (Last page) <CUT-ADJ>  -14/360, -9/360, -4/360, 0/360 4/360, 9/360, 14/360, GRAPHIC(*1) Compensates the line spacing pitch on the basis of the spacing error accumulated for feeding single sheets by10 inches. Decreases or increases in increments of 1/360 inch in total. <FCSFADJ>  -14/360, -9/360, -4/360, 0/360 4/360, 9/360, 14/360, GRAPHIC(*1) Compensates the line spacing pitch on the basis of the spacing error accumulated for feeding single sheets by10 inches. Decreases or increases in increments of 1/360 inch in total. This option is available only when paper is being loaded in the front cut sheet feeder. <RCSFADJ>  -14/360, -9/360, -4/360, 0/360 4/360, 9/360, 14/360, GRAPHIC(*1) Compensates the line spacing pitch on the basis of the spacing error accumulated for feeding single sheets by10 inches. Decreases or increases in increments of 1/360 inch in total. This option is available only when paper is being loaded in the rear cut sheet feeder.
USING SETUP MODE    5-40  User's Manual Table 5.5  ADJUST Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  ADJUST Items  Options Description <FCNTLOR>  0/9, 1/9, 1.8/9, 2/9, 3/9, 4/9, ..., 15/9 It is possible to fine-tune the left blank of the front continues form (the amount of between the left paper edge to the first dot for the first character).  This setting is effective only for the front continues form at < FCNT-SF:ENABLE >. <FCNTLFN>   0/90, ..., 29/90 It is possible to fine-tune the left blank of the front continues form by every 1/90 inches. <RCNTLOR>  0/9, 1/9, 1.8/9, 2/9, 3/9, 4/9, ..., 15/9 It is possible to fine-tune the left blank of the back continues form (the amount of between the left paper edge to the first dot for the first character).  This setting is effective only for the back continues form at < RCNT-SF:ENABLE >. <RCNTLFN>   0/90, ..., 29/90 It is possible to fine-tune the left blank of the back continues form by every 1/90 inches. <CUTLOR>  0/9, 1/9, 1.8/9, 2/9, 3/9, 4/9, ..., 15/9 It is possible to fine-tune the left blank of the cut sheet paper (the amount of between the left paper edge to the first dot for the first character).  This setting is effective only for the cut sheet paper at < CUT-SF:ENABLE >. <CUTLFN>   0/90, ..., 29/90 It is possible to fine-tune the left blank of the cut sheet paper by every 1/90 inches.
USING SETUP MODE   User's Manual  5-41 Table 5.5  ADJUST Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  ADJUST Items  Options Description <FCNTCUT>  71 /180, 74 /180, 78 /180, 81 /180, 85 /180, 88 /180, 92 /180, 95 /180, 99 /180, 102/180, 106/180, 109/180,113/180, 116/180, 120/180, 124/180, 128/180, 131/180,135/180, 138/180, 142/180 It is possible to set the amount of blank area of both sides of the front continues form. This setting is effective only for the front continues form at < FCNTARE:ENABLE1 or ENABLE2> <RCNTCUT>  71 /180, 74 /180, 78 /180, 81 /180, 85 /180, 88 /180, 92 /180, 95 /180, 99 /180, 102/180, 106/180, 109/180,113/180, 116/180, 120/180, 124/180, 128/180, 131/180,135/180, 138/180, 142/180 It is possible to set the amount of blank area of both sides of the back continues form. This setting is effective only for the back continues form at < RCNTARE:ENABLE1 or ENABLE2>.<CUT-CUT>  7  /180, 10 /180, 14 /180, 17 /180, 20 /180, 24 /180, 28 /180, 31 /180, 35 /180, 38 /180, 43 /180, 46 /180, 50 /180, 53 /180, 57 /180, 60 /180, 64 /180, 67 /180, 71 /180 It is possible to set the amount of blank area of both sides of the cut sheet paper.This setting is effective only for the cut sheet paper at < CUT-ARE:ENABLE1 or ENABLE2>. <FRCSLNT> 7 /360, 14/360,  21/360, 28/360,  35/360 It is possible to set the threshold of skew detection during manual paper insertion of a cut sheet.
USING SETUP MODE    5-42  User's Manual  Table 5.5  ADJUST Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  ADJUST Items  Options Description <==END==>    Indicates the end of MENU1 items. Press the  button to print the first item, <FCNTORG>.  Press the  button to print the previous item, < FRCSLNT>.  Press the ONLINE button to reprint the <<FUNCTION>> menu. *1:  When printing graphics, selecting “GRAPHIC” may result in the printing of clearer graphics.
USING SETUP MODE   User's Manual  5-43 The CONFIG function defines the printer’s primary configuration. You can set the following options to ensure that the printer meets your requirements:  Tear off for continuous forms  Auto loading of single sheets  Direct decoding of certain commands  Enabling of the AREA OVER indicator Table 5.6 describes the CONFIG items and options. Items are listed in the order they are printed. The procedure for changing the configuration options is described after Table 5.6. Table 5.6  CONFIG Items and Options NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <TEAROFF>    Auto or manual tear off  feed.   AUTO  Automatic tear off is valid but only for continuous forms. Tear off feed can also be done using the TEAR OFF button.  MANUAL Automatic tear off feed is invalid, and tear off feed must be done using the TEAR OFF button.  CHANGING CONFIGURATION OPTIONS
USING SETUP MODE    5-44  User's Manual Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <TEARPOS>    Tear off position.  VISIBLE Select this option when your software positions forms to the next top-of form after printing the last data. The printer performs tear off  feed without adding a form feed when data transfer has stopped.   ALWAYS  Select this option when your software stops after printing the last data. The printer performs tear off  feed after adding a form feed when data transfer has stopped.  Note: For both settings, tear off  positioning will fail if the page length setting does not match the actual perforation spacing. The following <TEAR-EN> item is printed when TEAROFF:AUTO is specified for the <TEAROFF> item. <TEAR-EN>    Tear off enabled time (offset time).  0 SEC 1 SEC 2 SEC 4 SEC 6 SEC The offset time is from when data transfer stops to when the printer performs automatic tear off  feed. If the printer receives data again within the offset time, the printer does not perform automatic tear off  feed.
USING SETUP MODE   User's Manual  5-45 Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <TEAR-EN> (continued)   In some application programs, data transfer may stop temporarily due to internal processing. This setting can avoid an undesired tear off feed by waiting for up to six seconds each time data transfer stops. <CUTLOAD>   Single sheet auto loading.  AUTO Single sheet paper is automatically loaded a certain time after you set the paper.   BUTTON  Single sheet paper can be loaded by pressing the LOAD button. The following <LOADTIM> item is printed when CUTLOAD:AUTO is specified for the <CUTLOAD> item. <LOADTIM>    Auto load start time.   0.5, 1.0, 1.5, 2.0 2.5, 3.0SEC Auto loading starts when this amount of time passes after you set single sheet paper. <DECODE>    Command decode timing.  DIRECT The printer decodes certain commands immediately after receiving data. Example: ESC SUB I, ESC CR  P (DPL24C+) ESC  Q # (IBM XL24E)   QUEUED  The printer decodes commands after storing all data (including commands) in the input buffer. This speeds data reception because the printer does not require decoding time during data reception.
USING SETUP MODE    5-46  User's Manual Table 5.7  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <FCNTARE>    Area-over detection control of front continuous forms.  ENABLE1 Detects the left and right edges of paper when loading the paper.    ENABLE2  Detects the left and right edges of paper at 13mm and 43mm from top of the paper.  This setting is effective if the left and right edges are not detected by <ENABLE1> for preprint papers, etc.   DISABLE  Does not detect the edges. Select this option when you are using colored or preprinted paper. <RCNTARE>    Area-over detection control of rear continuous forms.  ENABLE1 Detects the left and right edges of paper when loading the paper.    ENABLE2  Detects the left and right edges of paper at 13mm and 43mm from top of the paper.  This setting is effective if the left and right edges are not detected by <ENABLE1> for preprint papers, etc.   DISABLE  Does not detect the edges. Select this option when you are using colored or preprinted paper.
USING SETUP MODE   User's Manual  5-47 Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <CUT-ARE>    Area-over detection control of cut sheets.  ENABLE1 Detects the left and right edges of paper when loading the paper.    ENABLE2  Detects the left and right edges of paper at 13mm and 43mm from top of the paper.  This setting is effective if the left and right edges are not detected by <ENABLE1> for preprint papers, etc.   DISABLE  Does not detect the edges. Select this option when you are using colored or preprinted paper. <CUT-ONL>    Printer status after loading paper in offline mode for single sheets.   OFFLINE  Remains offline after paper loading. ONLINE Goes into online after paper loading. <CNT-ONL>    Printer status after loading paper in offline mode for continuous forms.   OFFLINE  Remains offline after paper loading. ONLINE Goes into online after paper loading.
USING SETUP MODE    5-48  User's Manual Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <LOCK>    Lock function of setup mode.  NONE Enables all buttons on the control panel.   SETUP  Disables the setup-related buttons to keep the printer from entering setup mode during the offline state.   ALL  Disables the setup-related buttons and the MENU button. Once this setting has been selected, setup mode cannot be entered from the control panel. To cancel this setting, turn the power on while simultaneously pressing the HI IMPACT, PAPER PATH, and LF/FF buttons. <//S//>    Effectiveness of the Cut Sheet Selection command (//S//).   ENABLE  Makes the command effective. Note:  The Cut Sheet Selection command (//S//) changes the paper source to the paper table and waits for manual insertion of a cut sheet.  DISABLE Makes the command ineffective. <FCNT-PE>    Detection of end of front continuous forms.  TRACTOR Paper end is detected by the sensor on the tractor unit. Paper-end unprinted area:  Continuous forms:  About 101 mm  EDGE Regardless of paper end, printing continues near to the edge of paper. Paper-end unprinted area:  About 4 mm for both continuous forms
USING SETUP MODE   User's Manual  5-49 Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <RCNT-PE>    Detection of end of rear continuous forms.  TRACTOR Paper end is detected by the sensor on the tractor unit. Paper-end unprinted area:  Continuous forms:  About 157 mm  EDGE Regardless of paper end, printing continues near to the edge of paper. Paper-end unprinted area:   About 4 mm for both continuous forms GATHER    Setting of ribbon protective control at a line feed on continuous forms   ENABLE  The protective control is executed.  DISABLE The protective control is not executed. CUT-CTL    Setting of retracting control at canceling TEAR OFF of continuous forms.  PRCISIN The precision-prioritized retracting control is executed. It retracts a certain amount of paper (the top part of the paper which hangs out from the TOFS), and then moves back to the position before TEAR OFF. If TOFS detects paper end when a certain amount of paper is retracted, it executes the continuous forms save operation and then executes the paper loading operation. SPEED The speed-prioritized retracting control is executed. It retracts the paper by the amount the paper was advanced.
USING SETUP MODE    5-50  User's Manual Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description SKIP-PR    Setting of printing speed change processing (skip)  ENABLE The skip processing is executed. When a certain amount of blank spaces are found in a line, it changes the printing speed for the blank spaces.   DISABLE  The skip processing is not executed. It does not change the printing speed for the blank spaces. -  If the printing speed of the printing data varies before and after the blank spaces (such as LQ characters + blank space + CQ characters), it changes printing speeds regardless of this setting. STATUS    Setting of the asynchronous status function   ENABLE  The status information is stored in the send buffer by a nibble mode request.  DISABLE The status information is not stored in the send buffer by a nibble mode request. BANDCTL    Setting of reducing backward line feeds as much as possible. Backward line feeds occur when printing vertical enlargement characters or multi-path characters which involve several printing paths for a print activation.   ENABLE  Reduce control is performed.  DISABLE Reduce control is not performed.
USING SETUP MODE   User's Manual  5-51 Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description TOF-CTL    Setting of priority on TOF control to a printer driver specification or a setup specification. TOF control determines the amout of the top margin when paper is fed to the home position.  DRIVER Driver specification is given priority.  SETUP  Setup specification is given priority. <FCNT-SF>    SET-FREE function of front continues papers is set. SET-FREE function is to adjust automatically the start printing position of print data by detecting the left edge position of paper during paper feeding.   EBANLE  Enables SET-FREE function  DISABLE Disables SET-FREE function <RCNT-SF>    Enables SET-FREE function of the back continues paper.   EBANLE  Enables SET-FREE function  DISABLE Disables SET-FREE function <CUT-SF>    Enables SET-FREE function of the cut sheet paper.   EBANLE  Enables SET-FREE function  DISABLE Disables SET-FREE function
USING SETUP MODE    5-52  User's Manual Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <CUTEDIR>    Selection of the eject direction of cut sheets with manually feeding of cut sheets  FRONT Ejected to the front.   REAR  Ejected to the rear. <CSFEDIR>    Selection of the eject direction of cut sheets with use of a CSF   FRONT  Ejected to the front.  REAR Ejected to the rear. <CUTEJCT>    Selection for automatic ejection of cut sheets  AUTO Automatic ejection of cut sheets when no cut sheet is detected   MANUAL  No automatic ejection of cut sheets when no cut sheet is detected <FL-CENT>   Selection of the print carrier position when paper is fed via a front path (with feeding of continuous forms paper from the front, use of a front CSF, and manual feeding of cut sheets)  POSN1  Position 1: Column 31  POSN2  Position 2: Column 42 <RL-CENT>    Selection of the print carrier position when paper is fed via a front path (with feeding of continuous forms paper from the rear and use of a rear CSF)  POSN1 Position 1: Column 31   POSN2  Position 2: Column 42
USING SETUP MODE   User's Manual  5-53 Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <SKEWCNT>   Detection of paper feed skew  PRCISIN Enables paper feed skew detection. Precision is the first priority.   SPEED  Enables paper feed skew detection. Speed is the first priority.   DISABLE  Disables paper feed skew detection. <FF-CODE>    Selection of the method of processing for the FF code is received in cut sheet mode or for the “LF/FF” switch  EJECT Ejects cut sheets.   FORM-FD  Uses a page break. <CSFBIN1>    Selection of the CSF for bin 1 if both a front CSF and rear CSF are mounted  FRONT  Front CSF  REAR Rear CSF <CNT-LD>    Selection for the paper feeding of continuous forms paper   PRCIS-1  Precision is the first priority.   PRCIS-2  Speed is the first priority. Reduces the disturbance of line break outstretching fold of the paper by over feeding during the process of paper feeding  SPEED Speed is the first priority.
USING SETUP MODE    5-54  User's Manual Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <CSF-LD>    Selection of the method of feeding from the CSF  NORMAL Feeds paper directly from the CSF hopper.   SWBACK Feeds paper from the CSF hopper to either the paper table cut sheet table used with a front CSF or the stacker used with a rear CSF.  Then, that paper is fed again. <CSFAPTC>    Paper thickness detection with use of a CSF  NORMAL Sheet of paper that is fed immediately after the feed bin is switched.  Detect the paper thickness at 1st page when printing from Cut sheet feeder continuously.   ALWAYS Detect the paper thickness of every paper when printing from Cut sheet feeder. <LF-CTL>    Selection for LF mode   PRCISIN  Precision is the first priority.  SPEED Speed is the first priority. <PR-MODE>    Selection for print mode  (standard/ hi speed /low noise)  NORMAL Prints in standard mode.   HISPEED  Prints in hi-speed mode.   QUIET  Prints in low-noise mode.
USING SETUP MODE   User's Manual  5-55 Table 5.6  CONFIG Items and Options (Cont.) NOTE: Underlined options are the factory defaults.  CONFIG Items  Options Description <HI-IMPT>    Selection for high impact mode   ENABLE  Prints in high impact mode.  DISABLE Prints in standard impact mode. <DQ-MODE >   Selection for draft quality printing mode   MODE1  Prints in 505CPS printing mode.  MODE2 Prints in 360CPS printing mode.   MODE3  Prints in 600CPS printing mode. <POW-POS >    It is possible to set the paper position at power on.  NORMAL Current position   TEAROFF  Tear off position <==END==>    Indicates the end of the CONFIG item list. Press the  button to print the first item, which is <TEAROFF>.Press the  button to print the previous item. Press the ONLINE button to reprint the <<FUNCTION>> menu.
USING SETUP MODE    5-56  User's Manual The GAP-ADJ function adjusts the gap between the print head and the paper. The automatic paper thickness control (APTC) feature is built in this printer. If you adjust the gap manually or fix the gap, change the option of GAP-ADJ function. For the procedure how to change the options refer to the section Setup Mode Example earlier in this chapter. Table 5.7  GAP-ADJ Items and Options NOTE: Underlined options are the factory defaults.  GAP-ADJ Items  Options Description <AMOUNT>    Specifies the print head gap.  AUTO The print head gap is set automatically.   MANUAL  Turn the paper thickness dial (indicator) manually. <==END==>    Indicates the end of the GAP-ADJ item list. Press the  button to print the first item, which is <AMOUNT>. Press the  button to print the previous item. Press the ONLINE button to reprint the <<FUNCTION>> menu.    This section describes how to exit setup mode and save any changes you made: HEAD GAP ADJUSTMENT ITEMS AND OPTIONS
USING SETUP MODE   User's Manual  5-57 To exit setup mode immediately, select the SAVE & END function. Any settings changed while in setup mode are saved as the new power-on defaults for the printer. The new defaults remain active until you change them again.  NOTE The only way to exit setup mode without saving your changes is to turn off the printer. When you turn the printer back on, the previous default settings are used. Procedure To exit setup mode and save your changes using SAVE/END, proceed as follows: 1.  Print the <<FUNCTION>> menu. The <<FUNCTION>> menu should be the last printed line on the page. If the menu is not printed, press the ONLINE button to print the menu. The <<FUNCTION>> menu is shown below:  << FUNCTION >> SAVE&END MENU1    MENU2    HARDWRE  ADJUST   CONFIG   GAP-ADJ  DEFAULT  LIST     SELF-TST  HEX-DUMP V-ALMNT  INITIAL  2.  Select the SAVE/END function. Make sure that the cursor on the left edge of the aluminum print guide is positioned under SAVE & END. Press the  button or the  button to select SAVE & END. The printer exits setup mode and returns online (the ONLINE indicator lights green). Any changes you made while in setup mode are saved.  EXITING AND SAVING
USING SETUP MODE    5-58  User's Manual This section describes how to reset the printer’s power-on defaults, all of the factory defaults, or the factory defaults only for MENU1 and MENU2. Resetting Power-On Defaults Power-on defaults are the settings saved in the printer’s permanent memory. The defaults are enabled whenever you turn the printer on. The easiest way to reset the power-on defaults is to turn the printer off and then on again. This method is useful if you have made changes in setup mode that you do not want to save. Resetting Factory Defaults Factory defaults are those settings preselected at the factory. For a list of the printer’s factory defaults, see the section Printing a List of Selected Options earlier in this chapter. To reset the factory defaults for all functions, proceed as follows: 1.  Turn off the printer. 2.  While pressing the LOAD and, TEAR OFF buttons, turn on the printer. Continue to press the two buttons until the printer beeps. The factory defaults are now reset. Another available method is to select INITIAL in SETUP mode.  The method of making settings is the same as the method for selecting DEFAULT on the next page, except that INITIAL must be selected instead of DEFAULT. Resetting Factory Defaults in MENU1 and MENU2 This method resets factory defaults for MENU1 and MENU2 options, listed in Table 5.3, but does not reset the printer hardware, print position adjustment, and configuration options. To reset the factory defaults in MENU1 and MENU2, proceed as follows: RESETTING DEFAULTS
USING SETUP MODE   User's Manual  5-59 1.  Enter setup mode. Press the SETUP button until the printer beeps. Wait for the printer to stop printing and check that the following <<FUNCTION>> menu is printed:  << FUNCTION >> SAVE&END MENU1    MENU2    HARDWRE  ADJUST   CONFIG   GAP-ADJ  DEFAULT  LIST     SELF-TST  HEX-DUMP V-ALMNT  INITIAL  2.  Select the DEFAULT function. Repeatedly press the “TEAR OFF” or “LOAD” button to position the cursor on the left edge of the aluminum print guide on DEFAULT. Press the  button or the  button to select the DEFAULT function. The printer reprints the <<FUNCTION>> menu. The default values in MENU1 and MENU2 are now reset. 3.  Do either of the following:   Select new options for MENU1 or MENU2.   Exit setup mode, saving the factory defaults. See the section MENU1 and MENU2 Items and Options. To exit setup mode and save the new defaults, make sure that the cursor on the left edge of the aluminum print guide are positioned on SAVE & END, then press the  MICRO button or the  MICRO button. This section describes how to use the following diagnostic functions:  SELF-TST  HEX-DUMP  V-ALMNT These functions are used for checking print quality and diagnosing printer problems. HEX-DUMP also provides useful information for programmers. Printing the Self-Test The SELF-TST function prints test pages to check how the printer operates independently of your computer. The self-test does not check the interface between the computer and the printer. The self-test prints the printer’s firmware version, its resident emulations, and all of the characters available in the currently selected character set. If the DPL24C PLUS emulation is selected for MENU1, the self-test is printed using the settings currently assigned to MENU1. USING THE DIAGNOSTIC FUNCTIONS
USING SETUP MODE    5-60  User's Manual Procedure This procedure assumes that you are in setup mode. To print the self-test,  make sure that continuous forms paper is loaded into the printer. Then proceed as follows: 1.  Print the <<FUNCTION>> menu. The <<FUNCTION>> menu should be the last printed line on the page. If the menu is not printed, press the ONLINE button to print the menu.  If you are using the HEX-DUMP function, press the “TEAR OFF” or “LOAD” button instead of the ONLINE button to print the menu.  The following <<FUNCTION>> menu is printed:    << FUNCTION >> SAVE&END MENU1    MENU2    HARDWRE  ADJUST   CONFIG   GAP-ADJ  DEFAULT  LIST     SELF-TST   HEX-DUMP V-ALMNT  INITIAL  2.  Select the SELF-TST function. Repeatedly press the “TEAR OFF” or “LOAD” button to position the cursor on the left edge of the aluminum print guide on SELF-TST, and then press the “ ” button or the “ ” button. The printer selects SELF-TST and starts printing. A short help menu is printed at the top of the page, followed by the self-test .  Note that the printer is not online during self-test printing. 3.  Examine the self-test page. A sample self-test page is shown in Chapter 2. To pause during self-test printing, press the “LOAD” button. To resume self-test printing, press the “LOAD” button again. 4.  Exit the SELF-TST function. Exit the SELF-TST function in either of the following ways:   To exit SELF-TST and remain in setup mode, press the LF/FF button. The <<FUNCTION>> menu is then reprinted.   To exit SELF-TST and return online, press the ONLINE button. The printer permanently saves any changes made while in setup mode and returns online. The self-test can also be started by turning off the printer, and then pressing the LF/FF button while turning the printer back on. As described in Chapter 2, this method is useful when you first set up the printer.
USING SETUP MODE   User's Manual  5-61 Printing Hex Dumps The HEX-DUMP function prints data and commands in hexadecimal characters and abbreviated control codes. The IBM character set 2 is used for printing (see Appendix E). The HEX-DUMP function is useful for checking whether your computer is sending the correct commands to the printer and whether the printer is executing the commands correctly. It is also useful for debugging software programs. Procedure To print hex dumps, make sure that continuous forms paper is loaded into the printer. Then proceed as follows: 1.  Enter setup mode. Press the SETUP button until the printer beeps. Wait for the printer to stop printing and check that the following <<FUNCTION>> menu is printed: 2.  Select the HEX-DUMP function.  << FUNCTION >> SAVE&END MENU1    MENU2    HARDWRE  ADJUST   CONFIG   GAP-ADJ  DEFAULT  LIST     SELF-TST  HEX-DUMP V-ALMNT  INITIAL  Repeatedly press the “TEAR OFF” or “LOAD” button to position the cursor on the left edge of the aluminum print guide on HEX-DUMP, then press the  button or the  button to select the HEX-DUMP function. The printer goes online and prints a header and a short help menu. 3.  Print the hex dump. To start hex dump printing, send your file or program to the printer. The printer goes online and prints the hex dump. Press the LOAD button to pause during hex dump printing. To resume hex dump printing, press the “LOAD” button again.  NOTE When hex dump printing stops, the printer remains online in setup mode (the ONLINE indicator is green). To print another hex dump, send another file to the printer.
USING SETUP MODE    5-62  User's Manual    Sample hex dump 4.  Exit the HEX-DUMP function. Exit the HEX-DUMP function in either of the following ways:   To remain in setup mode, press the LF/FF button.  The <<FUNCTION>> menu is then reprinted. For details on other functions, see other sections in this chapter.   To return to online normal mode, press the ONLINE button. If you press the ONLINE button while the hex dump is printing, the printer immediately switches to normal online mode, but data that was sent to the printer is printed. You can also enter hex dump mode, by turning off the printer, and then turning the printer back on while simultaneously pressing the ONLINE button and the LF/FF button until the printer beeps.
USING SETUP MODE   User's Manual  5-63 Checking Vertical Print Alignment (V-ALMNT) The V-ALMNT function corrects the vertical character displacement that sometimes occurs with bidirectional printing. Characters printed from left to right are not aligned with characters printed from right to left as shown below:  This example shows how printing looks  when characters are vertically misaligned. Note that the left  margin is not straight. If you notice misaligned printing, use the following procedure to check and correct the vertical print alignment. Procedure Make sure that continuous forms paper is loaded in the printer. If possible, use forms at least 356 mm (14 inches) wide to avoid printing on the platen. However, you can also use letter or A4 size forms if you set the WIDTH option in MENU1 to 8 inches. See the section Changing MENU1 and MENU2 Items and Options for details. Then proceed as follows to check and correct vertical print alignment: 1.  Enter setup mode. Press the SETUP button  until the printer beeps. Wait for the printer to stop printing and check that the following <<FUNCTION>> menu is printed:  << FUNCTION >> SAVE&END MENU1    MENU2    HARDWRE  ADJUST   CONFIG   GAP-ADJ  DEFAULT  LIST     SELF-TST  HEX-DUMP V-ALMNT  INITIAL  2.  Select the V-ALMNT function. Repeatedly press the “TEAR OFF” or “LOAD” button to position the cursor at V-ALMNT, then press the “” button or the “” button to select the V-ALMNT function. The printer prints the help menu then starts printing rows of parallel bars using letter quality speed.
USING SETUP MODE    5-64  User's Manual 3.  Adjust the vertical print alignment at letter quality speed. Examine the parallel bars. If the bars are aligned (not jagged), go to step 4. If the bars are offset to the left, repeatedly press the “” button until the bars are aligned. If the bars are offset to the right, repeatedly press the “” button until the bars are aligned. (In the following figure, the first line is assumed to be printed from left to right.)    Bars offset to the left  Bars offset to the right 4.  Adjust the vertical print alignment at correspondence speed. Press the “TEAR OFF” button to switch from letter speed to correspondence speed. Examine the parallel bars and adjust the vertical print alignment as described in step 3. Press the HI IMPACT button to enter Hi Impact mode.  Make similar adjustments. 5.  Adjust the vertical print alignment at draft speed. Press the “TEAR OFF” button to switch from correspondence speed to draft speed. Examine the parallel bars and adjust the vertical print alignment as described in step 3. Press the HI IMPACT button to enter Hi Impact mode.  Make similar adjustments. 6.  Adjust the vertical print alignment at high draft speed. Press the “TEAR OFF” button to switch from draft speed to high draft speed. Examine the parallel bars and adjust the vertical print alignment as described in step 3. Press the HI IMPACT button to enter Hi Impact mode.  Make similar adjustments.
USING SETUP MODE   User's Manual  5-65 7.  Adjust the vertical print alignment at super high draft speed. Press the TEAR OFF button to switch from high draft speed to super high draft speed. Examine the parallel bars and adjust the vertical print alignment as described in step 3. Press the HI IMPACT button to enter Hi Impact mode. Make similar adjustments HI IMPACT MODE of Vertical print alignment. 8.  Exit the V-ALMNT function. Press the ONLINE button to exit the V-ALMNT function and save the new vertical alignment settings. The printer exits setup mode and returns online. NOTE To exit the V-ALMNT function, you must exit setup mode.               Correct vertical print alignment  The following flowchart shows how setup mode is organized for the Fujitsu DPL24C PLUS emulation. Differences in the IBM Proprinter XL24E and Epson ESC/P2 emulations are summarized after the flowchart.  SETUP MODE REFERENCE
USING SETUP MODE    5-66  User's Manual DPL24C PLUS ORGANIZATION                              Note: Asterisks (*) indicate default setting at shipment. orororMove red cursor on the prime guide. Select function. Select option, print next item. Select option, print previous ite. Move red cursor on the prime guide.
USING SETUP MODE   User's Manual  5-67
USING SETUP MODE    5-68  User's Manual
USING SETUP MODE   User's Manual  5-69 Differences in IBM Proprinter XL24E Emulation In the IBM Proprinter XL24E emulation, MENU1 and MENU2 differ from the DPL24C PLUS emulation in the following ways:   The following options are different:    The AGM item is provided:  Differences in Epson ESC/P2 Emulation In the Epson ESC/P2 emulation, MENU1 and MENU2 differ from the DPL24C PLUS emulation in the following ways:   The  LF-CODE items are not defined.   The following options are different:
USING SETUP MODE    5-70  User's Manual The preceding sections describe offline setup mode. This section introduces online setup mode. The tedious task of setting up printer features one-by-one from the control panel and printing and checking the desired options on paper can be avoided by using online setup mode. In online setup mode, printer features are set via the computer rather than the printer control panel. Put the printer in online setup mode, in either of the following two ways:   Turn the printer off and then turn the printer back on while pressing the TEAR OFF button. Hold down the button until the printer beeps.   Issue the printer command ESC e ONLINE. This command is valid in any emulation. Send setup data from the computer in any of the following three ways:   Enter setup data directly from the computer keyboard before starting your job. With MS-DOS, hold down the Ctrl key and type P. Data entered from the keyboard is sent directly to the printer. When data entry is complete, hold down the Ctrl key again and type P. This method is useful when just a few settings need to be changed.   Use an editor program to prepare a setup data file and then send the file to the printer using a command before starting your job. With MS-DOS, use the COPY command. This method is useful when settings are used repeatedly.   Install a program that enables interactive entry of setup data on the screen. This method is the most useful of the three. This printer is provided with a CD which contains this program called DLMENU. Execute “setup.exe” in Utility folder of CD to install it. To exit from online setup mode, send EXIT as the last setup data. For details of setup data and its format, refer to the programmer’s manual for each emulation.   ONLINE SETUP MODE
  User's Manual  6-1 6  CHAPTER 6  MAINTENANCE MAINTENANCE Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Lubrication of the printer is usually not necessary. If the print head carriage does not move smoothly back and forth, clean the printer as described in this chapter. If the problem continues, contact your dealer to determine whether lubrication might be needed.  The front cover, the rear stacker, and the paper table of the printer help protect against dust, dirt, and other contaminants. However, paper produces small particles that accumulate inside the printer. This section explains how to clean and vacuum the printer and how to clean the platen. It is easier to clean the printer when the front cover and the rear stacker are removed. Cleaning and Vacuuming the Printer  WARNING To avoid any possibility of injury, before cleaning the printer, turn off the power to both the printer and the computer, and unplug the printer.  Use the following procedure to clean and vacuum the printer as required: 1.  Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer power cord. 2.  Using a soft vacuum brush, vacuum the exterior of the printer. Be sure to vacuum the air vents at the front, left sides, and bottom of the printer. Also vacuum the paper table, rear stacker, and the cut sheet feeder. 3.  Use a soft, damp cloth to wipe the exterior of the printer, including the cover, paper table, and rear stacker. A mild detergent may be used. CAUTION Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer. CLEANING
MAINTENANCE    6-2  User's Manual 4.  Open the front cover of the printer and remove the ribbon cartridge. Using a soft vacuum brush, gently vacuum the platen, print head carriage, and surrounding areas. You can easily slide the print head to the left or right when the power is off. Be careful not to press too hard on the flat ribbon cable that extends from the print head carriage.  Printer interior 5.  Re-install the ribbon cartridge. Close the front cover. 6.  Raise the paper table and rear stacker. Vacuum the forms tractors and surrounding areas. Cleaning the Platen Clean the platen about once a month to remove excess ink. Use the platen cleaner recommended by your supplier and proceed as follows: 1.  Apply a small amount of platen cleaner to a soft cloth. Avoid spilling platen cleaner inside the printer. CAUTION Do not use alcohol to clean the platen. Alcohol may cause the rubber to harden. 2.  Place the cloth against the platen. 3.  To dry the platen, place a dry cloth against the platen.
MAINTENANCE   User's Manual  6-3 There are two ways of replacing the ribbon. You can install a new ribbon cartridge in the printer or refill the old ribbon cartridge with new ribbon from a ribbon sub cassette. Appendix A lists order numbers for ribbon cartridges and ribbon sub cassettes. The following procedure is for ribbon cartridges. For ribbon sub cassettes, refer to the instructions shipped with the sub cassette. To replace the ribbon cartridge: 1.  Turn off the printer. Note: If the power is turned off during or immediately after printing, turn on the power again.  Verify that the print head has moved to the ribbon replacement position, and then turn off the power again. 2.  Open the front cover of the printer. For easy installation, slide the print head carriage to a position for replacing the ribbon cartridge (indicated by the triangle marking on the front of the upper cover).  (HOT) CAUTION <HOT> The print head and metal frame is hot during printing or immediately after printing.  Do not touch them until it cools down.   Preparing the printer to install the ribbon cartridge REPLACING THE RIBBON
MAINTENANCE    6-4  User's Manual 3.  To remove the ribbon cartridge, press the ribbon release levers located on either side of the cartridge and carefully lift the cartridge out of the printer.  Removing the ribbon cartridge 4.  Remove the new ribbon cartridge from its package. Push in the sides of the two ribbon release tabs. The tabs will snap into the cartridge and the ribbon feed mechanism will engage. Turn the ribbon feed knob clockwise to be sure that it feeds properly.   Preparing the new ribbon cartridge Ribbon feed knob Turn clockwise to tighten Ribbon release Mounting pin
MAINTENANCE   User's Manual  6-5 5.  Place the two mounting pins on the ribbon support brackets of the head cartridge. (The two mounting pins are located on the sides of the ribbon release levers.) Insert the ribbon so that the ribbon falls between the nose of the print head and the plastic print guide.  Installing the new ribbon cartridge 6.  Press the ribbon release levers until the mounting pins snap into the holes on the ribbon support brackets. Gently pull on the cartridge to verify that the pins are securely positioned in the holes. 7.  Turn the ribbon feed knob clockwise to tighten the ribbon. 8.  Close the front cover of the printer.  Note: The buzzer may sound if the print head is moved while the power supply is ON.
MAINTENANCE    6-6  User's Manual Opening and closing the control panel The control panel of this printer can be pulled down toward the front as necessary, such as when jammed paper must be removed.  The stacker unit of this printer can be removed in the event that paper is jammed in it unit. While pushing down the lock levers of the stacker guide, pull out the stacker unit from the rear.     OPENING AND CLOSING THE CONTROL PANEL REMOVING THE STACKER UNIT Lock lever Stacker guideLock lever Stacker
MAINTENANCE   User's Manual  6-7 Position groove 1 over guide pin 1 on the right and left sides of the stacker unit.  Then, push in the stacker unit until guide pin 2 is hooked onto slot 2.           MOUNTING THE STACKER UNIT Guide pin 2Guide pin 1Groove 1 Slot 2 Groove 1 Slot 2
  User's Manual  7-1 7  CHAPTER 7  TROUBLE-SHOOTING TROUBLE-SHOOTING Your printer is extremely reliable, but occasional problems may occur. You can solve many of these problems yourself, using this chapter. If you encounter problems that you cannot resolve, contact your dealer for assistance.  This chapter is organized as follows:  Solving problems  Diagnostic functions  Getting help  The tables in this section describe common printer problems and their solutions. The following types of problems are considered:   Print quality problems  Paper handling problems  Operating problems  Printer failures Print Quality Problems Poor print quality or other printing problems are often caused by incorrect printer setup or incorrect software settings. A gradual decrease in print quality usually indicates a worn ribbon. Table 7.1 identifies common print quality problems and suggests solutions.  SOLVING PROBLEMS
TROUBLE-SHOOTING    7-2  User's Manual Table 7.1  Print Quality Problems and Solutions Problem Solution Printing is too light or too dark. Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly. Check ribbon wear. Replace the ribbon if necessary. Check the difference of thickness of medium. If auto adjustment function detects difference level of medium, it doesn’t work properly. In this case you must adjust for paper thickness manually. See ADJUSTING PAPER THICKNESS in Chapter 3. If you adjust for paper thickness manually, tune-up as follows. If printing is too light, decrease setting. If printing is dark, increase setting. Note Printer accepts the value for paper thickness from Printer Driver or application program. In this case, check the setting of the Printer Driver or application program at your host computer. And then tune the value by way above.       Stains or smudges appear on the page. Check ribbon wear. Replace the ribbon if necessary. Check whether the tip of the print head is dirty. Clean the head with a soft cloth if necessary. The page is blank.  Make sure that the ribbon cartridge is properly installed. Printing is erratic or the wrong characters are printed. One or more “?” characters are printed. Make sure that the interface cable is securely connected to both the printer and computer. Make sure that the printer emulation selected in your software is the same as the emulation selected on the printer. See the section Selecting an Emulation in Chapter 2. If you are using an RS-232C serial interface, make sure that the serial settings required by your software or computer are the same as the settings on the printer. See the section Hardware Items and Options in Chapter 5.
TROUBLE-SHOOTING   User's Manual  7-3 Table 7.1  Print Quality Problems and Solutions (Cont.) Problem Solution Characters are lost at the left or right end. If lost area is about 10mm (3mm) from left and right edge of continuous forms(single sheet), Area-over detection control woks properly.  In this case make sure that paper size, paper position, and left and right margins are properly set. See the section Configuration Items and Options in Chapter 5. Note Preprinted dark color area, shape of corner cut, paper skew may cause incorrect detection. Please don’t use medium like this. If you must use medium like this absolutely, you can disable Area-over detection by using setup mode. But risk of print head broken is increase.     Incorrect paper size selection of the Printer Driver causes right side area to be  lost (exactly Printer Driver divide the page by paper size setting and postpone divided right page). Please check the paper size setting. Printing is vertically misaligned (jagged). Use the printer’s V-ALMNT function to check the vertical print alignment. If necessary, adjust the print alignment. See the section Using the Diagnostic Functions in Chapter 5. Smaller adjustment for paper thickness causes vertically misalignment too.  Please refer to Printing is too light or too dark. The top margin is wrong. The top margin is the sum of the top-of-form setting, the software-specified top margin, and the printer’s TOP-MRG setting. Proceed as follows:  Make sure that the top-of-form setting is correct. The factory default is 25.4 mm (1 inch). See the section Changing Top-of Form in Chapter 5.  Check the software-specified top margin.  Refer to your software documentation.  Check the printer’s TOP-MRG setting. See the section MENU1 and MENU2 Items and Options in Chapter 5.
TROUBLE-SHOOTING    7-4  User's Manual Table 7.1  Print Quality Problems and Solutions (Cont.) Problem Solution Lines are double spaced instead of single spaced. Check the line spacing setting in your software. Change the CR-CODE setting in the printer setup mode to CR ONLY. See the section MENU1 and MENU2 Items and Options in Chapter 5. The printer overprints on the same line. Change the CR-CODE setting in the printer setup mode to CR & LF. See the section MENU1 and MENU2 Items and Options in Chapter 5. The next print line starts where the previous line ended instead of at the left margin. Change the LF-CODE setting in the printer setup mode to LF & CR. See the section MENU1 and MENU2 Items and Options in Chapter 5. The top of form of continuous form displaces gradually. Variation of the top of form is saturated in a few pages and displacement is about 1mm or less. In this case adjust value is prepared in setup mode. See ADJUST Items and Options and search <FCNTADJ> or <RCNTADJ>. Variation of the top of form isn’t saturated. In this case setting of page length isn’t correct. Make sure that page length setting equal actual page length exactly.  In general page length of continuous form is multiple of 0.5inch. Anyway don’t set page length of continuous forms using mm unit.
TROUBLE-SHOOTING   User's Manual  7-5 Paper Handling Problems Table 7.2 describes common paper handling problems and suggests solutions. See Chapter 3 for detailed procedures on loading and using paper. Table 7.2  Paper Handling Problems and Solutions Problem Solution Paper cannot be loaded or fed. Make sure that the paper path indicator (FRONT TRACTOR, REAR TRACTOR, CUT SHEET) lights correctly. Press the PAPER PATH button to select the paper path. Make sure that the paper covers the paper-out sensor, i.e., the left paper edge is within 52 mm for single sheets or 41 mm for continuous forms from the left edge of the platen. (This problem cannot occur if you use the forms tractor unit or insert a single sheet with its left edge in contact with the left paper guide.) Make sure that the tractor unit is correctly installed and that the tractor shaft gear engages the platen shaft gear. If you are using a cut sheet feeder, make sure that the bin lever is set to the “CLOSED” position. (The bin lever is on the left side of the feeder.) If you are using a cut sheet feeder, make sure that the feeder is firmly mounted on the printer and the cable is correctly connected. Paper manually loaded is ejected without printing If you are using the paper skew detection (option), adjust the paper guide on the paper table for the print start position and correctly slide the sheet along the guide.
TROUBLE-SHOOTING    7-6  User's Manual Table 7.2 Paper Handling Problems and Solutions (Cont.) Problem Solution Paper jams while loading. Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. If you are using a cut sheet feeder, make sure that the bin lever is set to the “CLOSED” position. (The bin lever is on the left side of the feeder.) Make sure that the paper is not folded, creased, or torn. Reload the paper. Make sure that the paper table is in normal mode. Set the paper table to normal mode. Paper jams while printing. Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. For continuous forms, make sure that the incoming and outgoing paper stacks are correctly placed. Paper should feed straight. Make sure that the paper table is in normal mode. Set the paper table to normal mode. If you are using a cut sheet feeder, make sure that the bin lever is set to the “CLOSED” position. (The bin lever is on the left side of the feeder.) Reload the paper. Paper slips off the forms tractors or the perforated holes of the paper tear during printing. Make sure that the forms tractors are positioned correctly for the width of your paper and that the perforated holes of the paper fit directly over the tractor sprockets.
TROUBLE-SHOOTING   User's Manual  7-7 Operating Problems Table 7.3 identifies common operating problems and suggests solutions. If you cannot resolve a problem, contact your dealer. Table 7.3 Operating Problems and Solutions Problem Solution The power does not turn on. Make sure that the “I” on the printer power switch is depressed. Make sure that the power cord is securely connected to both the printer and the outlet.  Make sure that the power outlet is functional. Turn the power off. Wait 100 seconds and then turn the printer on again. If the printer still has no power, contact your dealer. The printer is on but it will not print. Make sure that the printer is online. Make sure that the interface cable is securely connected to both the printer and the computer. If the red PAPER OUT indicator is lit, load paper. Run the printer self-test (see Chapter 5). If the self-test executes normally, the problem is caused by the interface, the computer, incorrect printer settings, or incorrect software settings. Make sure that the printer emulation selected in your software is the same as the emulation selected on the printer. See the section Selecting an Emulation in Chapter 2. Make sure that the front cover is completely closed. If you are using an RS-232C serial interface, make sure that the serial settings required by your software or computer are the same as the settings on the printer. See the section Hardware Items and Options in Chapter 5. The cut sheet feeder does not operate. Make sure that the cut sheet feeder is firmly mounted on the printer. Make sure that the cable is correctly connected. The FRONT DIR indicator blinks. Remove the printed sheet of paper from the paper table.
TROUBLE-SHOOTING    7-8  User's Manual Printer Failures A user cannot generally resolve a problem involving defective printer hardware. On detecting a fatal error, the printer will:   Stop printing  Beep four times   Turn the ONLINE indicator off The control panel displays alarms.  The meanings of alarms can be checked in the following table.
TROUBLE-SHOOTING   User's Manual  7-9 Alarm display function This printer has a function for distinguishing between alarms by using the blinking of individual lamps on the control panel. From the combination of blinking lamps in an alarm state, the meaning of the alarm can be determined as shown in the following table. Lamp    Alarm name PAPER OUT REMOVE PAPER FRONT DIR QUIET AUTO GAP HI IMPACT TRACTOR F TRACTOR R CUT SHEET MENU1 MENU2 ONLINE Condition of occurrenceLES alarm             LES could not be detected during the space initial operation. Space problem alarm                 The shield board could not be detected normally by the LRES sensor. Fan alarm                The cooling fan for the space motor was stopped. HCPP (cut sheet or continuous forms paper switching) alarm            Switching between cut sheet paper and continuous forms paper was not possible. Overload alarm            An overload occurred during printing, and tripartite printing was performed.  However, the power source voltage was not restored. Low voltage alarm                The power source voltage dropped below the specified level when no printing was in progress. APTC gap alarm            During the APTC operation, paper was detected immediately after the start of approach motion, or no paper was detected. APTC hop position sensor alarm           During the APTC operation, no reference position was detected. ROM/RAM alarm                   A sum-check error or read/write error occurred, or no CG-ROM is mounted. Sector protect alarm                A sector protect check of flash ROM was performed, but no sector protect information was found. :  Blinking Blank: Off
TROUBLE-SHOOTING    7-10  User's Manual Responses to alarm occurrences Your first response to each alarm should be as described in the following table.  Problem Solution LES alarm Remove any paper dust, which may cause problems in carriage operation. APTC gap alarm Check the paper thickness (0.04 to 0.57 mm). Check whether the paper has different thicknesses or whether the paper has filing holes.  For problems other than the above, request your printer dealer to make repairs. The following errors cause the printer to turn off the power:  Print head error   Space motor error   Line feed motor error   +34 V overvoltage error No error condition is displayed if any of these errors occurs. Turn the printer off and back on, then rerun the same job to check if the error was transient. If the error recurs, contact your dealer.  The printer diagnostic functions are SELF-TST, HEX-DUMP, and V-ALMNT.   SELF-TST tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer.   HEX-DUMP allows you to determine whether the computer is sending the correct commands to the printer, and whether the printer is executing the commands correctly. This function is useful to programmers or others who understand how to interpret hex dumps.   V-ALMNT allows you to check and, if necessary, correct the printer’s vertical print alignment. For details on using these functions, all of which are available in the printer setup mode, see the section Using the Diagnostic Functions in Chapter 5. DIAGNOSTIC FUNCTIONS
TROUBLE-SHOOTING   User's Manual  7-11 If you are not able to correct a problem using this chapter, contact your dealer for assistance. Be prepared to provide the following information:   Your printer model number, serial number, and date of manufacture. Look for this information on the rating label at the back of the printer.   Description of the problem   Type of interface you are using   Names of your software packages   List of the printer default settings. To print the default settings, see the section Printing a List of Selected Options in Chapter 5.   GETTING HELP
TROUBLE-SHOOTING    7-12  User's Manual
  User's Manual  8-1 8  CHAPTER 8  INSTALLING OPTIONS INSTALLING OPTIONS The installation  of options allows you to expand  the capabilities of your printer. Options available for the printer include:  LAN card   Cut sheet feeder  Tractor unit  Large stacker   Small paper table    Sound proof cover The LAN card is a user installable option, but can be installed only on a printer model with the parallel and USB interfaces. For information on the installation procedure, refer to the manual that comes with the LAN card. Options can be purchased from your dealer. Order numbers for options are given in Appendix A.  This section explains how to install the LAN card. WARNING (Electric shock) Before mounting or removing the LAN card, turn off the power switches of the personal computer and the printer and remove the power plug from the outlet.  Otherwise, you may receive electric shock. 1.  Turn the power off. Make sure that the power switch is set to the “○”side, and make sure that a power plug is disconnected from an outlet.   INSTALLING THE LAN card
INSTALLING OPTIONS    8-2  User's Manual 2.  Remove metal plate Remove two screws and metal plate on the parallel port. Keep metal plate removed.         3.  Insert LAN card Insert the LAN card along both sides of guide rails slowly.   Make sure that LAN card is inserted all the way into the slot.         4.  Tighten the LAN card Tighten the LAN card with two screws removed in step 2.         LAN card Metal plate
INSTALLING OPTIONS   User's Manual  8-3 5. Connect LAN cable After tightening LAN card, connect LAN cable first, then the power plug. Please refer to the manual attached to LAN card about LAN card setting.          This chapter describes what to do after installing cut sheet feeder. A cut sheet feeder (SF940) allows you to automatically feed single sheets.  It can be mounted on the front or the rear of the printer. When attaching the cut sheet feeder to the front of the printer, remove the tractor  For both front and rear, the cut sheet feeder can handle a max. of 5-ply multipart media. When installing the front and rear cut sheet feeders, the printer assigns the first bin to the front feeder.  You can change the assignment using set up mode. WARNING (Electric shock) Before mounting or removing the cut sheet feeder, turn off the power switches of the personal computer and the printer and remove the power plug from the outlet.  Otherwise, you may receive electric shock.  INSTALLING THE CUT SHEET FEEDER LAN cable
INSTALLING OPTIONS    8-4  User's Manual Installing on the front side of the printer 1.  Turn off the printer power. Confirm that the printer power is turned to the  side. 2.  Removing the tractor unit Raise the paper table and remove the tractor unit.  (For details on mounting and removing the tractor unit, see “Selecting the tractor Unit Position” on page 2-9 .)             3.  Installing the cut sheet feeder Adjust the U slots made on both sides of the cut sheet feeder to the mounting pins inside the printer and lower the cut sheet feeder slowly.    Paper table Tractor unit
INSTALLING OPTIONS   User's Manual  8-5 Check that the cut sheet feeder frame is correctly mounted on mounting pin 2.  4.  Replacing the paper table Be sure to replace the paper table.  (See “Handling the paper table” on page 2-5.) If the paper table is incorrectly set, a paper jam may occur. 5.  Connecting the cable Connect the cut sheet feeder cable to the connector on the front right of the printer.  Insert the cable with the connector arrow mark up.
INSTALLING OPTIONS    8-6  User's Manual 6.  Extend the extension and extension wire in the order from (1) to (2) according to the size of the paper to be used.  Installing on the rear side of the printer Before mounting the cut sheet feeder, turn off the printer power. 1.  Turn off the printer power. Confirm that the printer power is turned to the O side. 2.  Installing the cut sheet feeder Open the rear stacker.  Hold both sides of the cut sheet feeder and adjust the U slots made on both side of the cut sheet feeder to the mounting pins inside the printer.  (Attach the slots with the letter A of the cut sheet feeder adjusted to that on the printer side.)  Then, lower the cut sheet feeder like it turns in the direction of arrow B, using the mounting pins as supporting points.
INSTALLING OPTIONS   User's Manual  8-7 Check that the cut sheet feeder frame is correctly mounted on mounting pin 2.  3.  Close the rear stacker.
INSTALLING OPTIONS    8-8  User's Manual 4.  Connecting the cable Connect the cut sheet feeder cable to the connector on the rear right of the printer.  Insert the cable with the connector arrow mark up.  5.  Extend the extension and extension wire in the order from (1) to (2) according to the size of the paper to be used
INSTALLING OPTIONS   User's Manual  8-9 Removing the Cut Sheet Feeder Before removing the cut sheet feeder, disconnect the cable.  WARNING (Electric shock) Before mounting or removing the cut sheet feeder, turn off the power switches of the personal computer and the printer and remove the power plug from the outlet.  Otherwise, you may receive electric shock.   When mounted on the front side of the printer  Cable
INSTALLING OPTIONS    8-10  User's Manual When mounted on the rear side of the printer   A tractor unit is supplied as standard equipment attached to the front of the printer.   This unit may also be attached to the rear of the printer for rear feeding of continuous forms. For details on removing and mounting the tractor unit, see “Mounting and removing the tractor unit” on page 2-10.   INSTALLING THE TRACTOR UNIT Cable
INSTALLING OPTIONS   User's Manual  8-11 To stack cut sheets continuously or eject long cut sheets to the rear, mount the large stacker. Also, if a cut sheet feeder is mounted at the rear, the stacker must be replaced with the large stacker even if cut sheets need not be continuously stacked. 1 Removing the current stacker 1.  Lift up the current stacker in the direction indicated by the arrow. 2.  With the stacker in the condition described in step 1, push out the right and left stacker frames to separate them from the protrusions on the stacker plate.  INSTALLING THE LARGE STACKER
INSTALLING OPTIONS    8-12  User's Manual 2 Mounting the rear stacker At the rear of the printer, push the protrusions on both sides of the rear stacker into the holes inside the rear stacker guide as shown in the following figure.
INSTALLING OPTIONS   User's Manual  8-13 Please install it when you use only a short cut sheet. 1 Removing the current paper table After opening the paper table and adjusting it to a tilted position, remove the paper table by pulling it to separate the left and right protrusions on the paper table ends from the grooves on the cover.          INSTALLING THE SMALL PAPER TABLE
INSTALLING OPTIONS    8-14  User's Manual 2  Installing the Small Paper Table Insert and push the left and right protrusions on the paper table ends into the grooves on the cover as shown in the following figure.  Set the paper table in the normal position. (See “Handling the paper table” in Chapter 2.) The paper table can be opened or closed in the same way as the removed current paper table.         Make sure the protrusions are inserted completely as left figure.
INSTALLING OPTIONS   User's Manual  8-15 The Acoustic noise  can be decreased by installing Sound proof cover.  However, the cut sheet and Cut Sheet Feeder cannot be used. 1 Removing the current paper table  After opening the paper table and adjusting it to a tilted position, remove the paper table by pulling it to separate the left and right protrusions on the paper table ends from the grooves on the cover.      INSTALLING THE SOUND PROOF COVER
INSTALLING OPTIONS    8-16  User's Manual 2  Installing the Sound Proof Cover Insert and push the left and right protrusions on the paper table ends into the grooves on the cover as shown in the following figure.  Set the paper table in the normal position. (See “Handling the paper table” in Chapter 2.) The paper table can be opened or closed in the same way as the removed current paper table.       Make sure the protrusions are inserted completely as left figure.
  User's Manual  A-1 A  APPENDIX A  SUPPLIES AND OPTIONS SUPPLIES AND OPTIONS This appendix lists the supplies and options available for the printer. Contact your dealer for information on ordering any of these items.  Supplies Order Number Ribbon cartridges   Black ribbon  KA02086-C802 Ribbon subcassette   Black ribbon  KA02086-C872   Options Order Number Description LAN card  KA02086-C130  Installable only on a printer model with the parallel and USB interfaces. Cut sheet feeder (SF940) KA02027-D750  Tractor Unit  KA02038-E650   Large Stacker  KA02086-D160   Small paper table  KA02086-D170   Sound proof cover  KA02086-D190     SUPPLIES OPTIONS
  User's Manual  B-1 B  APPENDIX B  PRINTER AND PAPER SPECIFICATIONS PRINTER AND PAPER SPECIFICATIONS This appendix gives the physical, functional, and  performance specifications for the printer. It also gives detailed paper specifications.  Dimensions Height: 290 mm (11.4 in) Width: 600 mm (23.6 in) Depth: 350 mm (13.8 in) Weight:  17 kg (37.4 lb) AC power requirements M33334A : 100 to 120 V ±10%; 50/60 Hz M33334B  : 220 to 240 V ±10%; 50/60 Hz Power consumption  Average 210 VA Maximum 360 VA Standby    1W Heat generation Average 420kJ/h Interface  -  Centronics parallel and RS-232C serial -  Centronics parallel and USB and LAN   (option). Data buffer size  0, 256, 2K, 8K, 24K, 32K, 96K, or 128K bytes Download buffer  Maximum 128K bytes (128K minus data buffer size) Operating environment  5 to 38°C (41 to 100°F) 30% to 80% RH (no condensation) Wet bulb  temperature, less than 29°C (84°F) Storage environment  -15 to 60°C (-4 to 140°F) 10% to 95% RH (no condensation) Acoustic noise  Standard model :Average 59 dB (A) Install sound proof cover : Average  55 dB (A) ISO 7779 (Bystander Position-Front)  PHYSICAL SPECIFICATIONS
PRINTER AND PAPER SPECIFICATIONS    B-2  User's Manual Print method Impact dot matrix with a 0.2 mm, 24-wire head Print direction  Bidirectional logic-seeking or unidirectional seeking Character cell Horizontal  vertical Letter (10 cpi): 36  24 dots Letter (12 cpi): 30  24 dots Report: 18  24 dots Draft: 9  24 dots   (MODE 1) 12  24 dots  (MODE 2) High-speed draft: 9  24 dots Paper handling  Standard: Friction-feed platen (cut sheets) Convertible bi-directional tractor on front or rear Paper loading by LOAD button Advancing perforations to tear-off edge by TEAR OFF button Parking continuous forms when using cut sheetsOptional: Cut sheet feeder Tractor unit Paper type  1 to 5-copies for cut sheet feeder 1 to 8-copies for tractor and paper table Paper size   Continuous  Width: 102-420 mm (4-16.5 in)   Length: 102 mm (4 in) or greater Cut sheets  (Paper table) Width: 55-420 mm (2.16-16.5 in)   Length: 70-420 mm (2.76-16.5 in) (Cut sheet feeder)     Width: 100-420 mm (4-16.5 in)  Length: 70-420 mm for front cut sheet feeder  (2.76-16.5 in)  100-420 mm for front cut sheet feeder  (4-16.5 in) Note: To use cut sheets exceeding 297 mm in length, the optional  large stacker is required. For detail see Chapter 3. FUNCTIONAL SPECIFICATIONS
PRINTER AND PAPER SPECIFICATIONS   User's Manual  B-3 Paper thickness Up to 0.57 mm (0.022 inch) Paper length  By software Programmable in one line or inch increments in all emulations By control panel  Depends upon emulations. Default is 11 inches for all emulations. DPL24C+/XL24E: 3, 3.5, 4, 5, 5.5, 6, 7, 8, 8.5, 11, 11.6, 12, 14, or 18 inches ESC/P2: 4, 4.5, 5, 5.5, ..., 11, 11.5, ..., 22 inches Number of copies  Up to 5, including the original (normal mode) Up to 8, including the original (HI IMPACT mode) Paper stack   Cut sheet 100 sheets (A4 size, 1p, 55 kg/m2) (The stack of cut sheets may decrease, depending upon the various paper conditions such as quality, the extent of curl, and storage environment.) Command sets (emulations)   Resident  Fujitsu DPL24C PLUS IBM Proprinter XL24E Epson ESC/P2 Character sets   DPL24C+/XL24E:  IBM PC character sets 1 and 2 (code pages 437)  IBM PS/2 character sets (code pages and other national character sets (57 + 2 languages in total)  Fujitsu character sets (691 characters) ESC/P2:  Italic character set Graphics character sets 1 and 2  IBM PS/2 character sets (code pages) and other national character sets (61 + 2 languages in total)
PRINTER AND PAPER SPECIFICATIONS    B-4  User's Manual Fonts   Resident Nineteen fonts available Bit map: Courier 10, Pica 10, OCR-B 10, OCR-A 10 , Prestige Elite 12, Boldface PS, Correspondence, Compressed, Draft, and High-speed Draft. Scalable: Courier, Timeless, and Nimbus Sans ®; each in normal, bold, and italic styles Downloaded  Available from independent vendors Line spacing 1, 2, 3, 4, 5, 6, 7, or 8 lines per inch.  Programmable in 1/360 inch or various increments for image graphics. Character pitch 2.5, 3, 5, 6, 10, 12, 15, 17.1, 18, or 20 cpi, or proportional spacing. Programmable in 1/360 inch or various increments for image graphics. Characters per line   10 cpi: 136 cpl 12 cpi: 163 cpl 15 cpi: 204 cpl 17.1 cpi: 232 cpl 18 cpi: 244 cpl 20 cpi: 272 cpl   cpi: characters per inch cpl: characters per line
PRINTER AND PAPER SPECIFICATIONS   User's Manual  B-5  Print speed  10 cpi 12 cpi Letter: 120 cps  144 cps Report: 240 cps  288 cps Correspondence: 240 cps  288 cps Draft: 505 cps    606 cps  (MODE 1) 360 cps    432 cps  (MODE 2) High-speed draft: 505 cps    606 cps Super hi-speed draft    cpi: characters per inch cps: characters per second Line feed speed  60 ms per line at 6 lines per inch Form feed speed  6 inches per second Ribbon life  Up to 5 million characters Certification  Safety:  Model Regulation Country M33334A  UL60950-1 United States (for 100 V to 120 V) United States   CSA C22.2 No. 60950-1 (for 100 V to 120 V) Canada  M33334B  EN 60950-1 (for 220 V to 240 V) Europe   EMI regulation: Model Regulation Country M33334A  CFR 47 FCC Part 15 Subpart B class B  United States   ICES-003 class B  Canada   CNS 13438 class B  Taiwan M33334B  EN 55022 class B   Europe  AS/NZS CISPR22 class B  Australia and New Zealand   PERFORMANCE SPECIFICATIONS
PRINTER AND PAPER SPECIFICATIONS    B-6  User's Manual Print Area This section illustrates the recommended print area for single sheets and continuous forms.  Print area for single sheets PAPER SPECIFICATIONS (2.75-16.5in) 4.230.16 0.16 4.23
PRINTER AND PAPER SPECIFICATIONS   User's Manual  B-7  Print area for continuous forms    Approx. 101 mm (4 inches)   for front tractor feed Approx. 157 mm (6.2 inches)  for rear tractor feed 4.234.234.230.160.160.16
PRINTER AND PAPER SPECIFICATIONS    B-8  User's Manual Paper Thickness Paper thickness is given by the weight of the paper in either grams per square meter (g/m2) or in pounds per bond (lbs/bond). The following table shows the allowable paper thickness for one-part paper or for each sheet of multipart paper. The total thickness must not exceed 0.57 mm (0.022 inch). The weight of carbonless or carbon-backed paper may vary, depending upon the paper manufacturer. When using paper of borderline thickness, test the paper before running a job.  Type of Paper Number of Parts  Thickness One-part Single  47-81 g/m2 (40-70 kg or 12-22 lb) Carbonless  Top Bottom  40-64 g/m2 (34-55 kg or 11-17 lb) 40-81 g/m2 (34-70 kg or 11-22 lb) Top Middle Bottom 40-50 g/m2 (34-43 kg or 11-13 lb) 40-50 g/m2 (34-43 kg or 11-13 lb) 40-81 g/m2 (34-70 kg or 11-22 lb) Top Middle (2-3p) Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-81 g/m2 (34-70 kg or 11-22 lb) Top Middle (2-4p) Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) Top Middle (2-5p) Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) kg:  Weight in kilograms of 1000 sheets of 788  1091 mm paper (1.16 g/m2) lb:  Weight in pounds of 500 sheets of 17  22 inch paper (3.76 g/m2)
PRINTER AND PAPER SPECIFICATIONS   User's Manual  B-9 Type of Paper Number of Parts  Thickness Carbonless  Top Middle (2-6p)Bottom  40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) Top Middle (2-7p)Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) Carbon-backed  Do not use in high humidity environments. Top Bottom 40-64 g/m2 (34-55 kg or 11-17 lb) 40-81 g/m2 (34-70 kg or 11-22 lb) Top Middle Bottom 40-52 g/m2 (34-45 kg or 11-14 lb) 40-52 g/m2 (34-45 kg or 11-14 lb) 40-81 g/m2 (34-70 kg or 11-22 lb) Top Middle (2-3p)Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-81 g/m2 (34-70 kg or 11-22 lb) Top Middle (2-4p)Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) Top Middle (2-5p)Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) kg:  Weight in kilograms of 1000 sheets of 788  1091 mm paper (1.16 g/m2) lb:  Weight in pounds of 500 sheets of 17  22 inch paper (3.76 g/m2)
PRINTER AND PAPER SPECIFICATIONS    B-10  User's Manual Type of Paper Number of Parts  Thickness Carbon-backed  Do not use in high humidity environments. Top Middle (2-6p)Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) Top Middle (2-7p)Bottom 40 g/m2 (34 kg or 11 lb) 40 g/m2 (34 kg or 11 lb) 40-64 g/m2 (34-55 kg or 11-17 lb) Carbon-interleaved Avoid using carbon-interleaved single sheets. Top Carbon Bottom 35-52 g/m2 (30-45 kg or 9-14 lb) Counted as one sheet 35-81 g/m2 (30-70 kg or 9-22 lb) Top Carbon Middle Carbon Bottom 35-46 g/m2 (30-40 kg or 9-12 lb) Counted as one sheet 35-46 g/m2 (30-40 kg or 9-12 lb) Counted as one sheet 35-64 g/m2 (30-55 kg or 9-17 lb) Top Carbon Middle (3,5P)Carbon (4,6P)Bottom 35-46 g/m2 (30-40 kg or 9-12 lb) Counted as one sheet 35-46 g/m2 (30-40 kg or 9-12 lb) Counted as one sheet 35-64 g/m2 (30-55 kg or 9-17 lb) kg:  Weight in kilograms of 1000 sheets of 788  1091 mm paper (1.16 g/m2) lb:  Weight in pounds of 500 sheets of 17  22 inch paper (3.76 g/m2)
  User's Manual  C-1 C  APPENDIX C  COMMAND SETS COMMAND SETS This appendix describes printer commands and their parameters. This printer has three resident command sets:  Fujitsu DPL24C PLUS (native command set for Fujitsu DL series printers)  IBM Proprinter XL24E  Epson ESC/P2 Separate programmer s manuals are available for these emulations. See Appendix A for order information. Select the same emulation on the printer and in your software. If your software emulations include DPL24C PLUS, select DPL24C PLUS for optimum performance.
COMMAND SETS (DPL24CPLUS)    C-2  User's Manual This section describes the printer commands for the DPL24C PLUS command set which is the native command set of this printer.  Function Command Print Mode Control Double-strike (bold) printing on Double-strike (bold) printing off Emphasized (shadow) printing on Emphasized (shadow) printing off Italic printing on Italic printing off Select character style and screening   n1= 0:Normal  1:Outline  2:Shaded  3:Outline and shaded  4:Thin outline  5:Thin shaded   6:Thin outline and shaded n2= 0:Transparent  1:Light dot matrix   2:Heavy dot matrix  3:Vertical bars  4:Horizontal bars  5:Slants  6:Back slants  7:Lattice One-line double width characters on  One-line double width characters off  Double width characters on/off  (on: n = 1, off: n = 0)  ESC G ESC H ESC E ESC F ESC 4 ESC 5 ESC e S (n1) (n2)                SO or ESC SO DC 4 ESC W (n)    FUJITSU DPL24C PLUS
COMMAND SETS    User's Manual  C-3 Function Command Double-height characters on/off  (on: n = 1, off: n = 0) This command does not adjust the line spacing. Multiwidth and height printing  n =  0: Not adjusted   1: Character pitch multiplied   2: Line spacing multiplied   3: Character pitch and line spacing   multiplied h1:  Tens digit of horizontal multiple h2:  Units digit of horizontal multiple v1:  Tens digit of vertical multiple v2:  Units digit of vertical multiple (0 < h1h2 or v1v2 < 11) Condensed characters on  Condensed characters off  Subscript or superscript printing on  (subscript: n = 1, superscript: n = 0) Subscript and superscript printing off  Select underline type  n =  0:Single line  1:Bold single line   2:Extremely bold single line  3:Double line   4:Bold double line   5:Extremely bold double line Underline on/off  (on: n=1, off: n=0) Overline on/off  (on: n=1, off: n=0) ESC V (n)    ESC u (n) (h1) (h2) (v1) (v2)          SI or ESC SI DC2 ESC S (n)  ESC T ESC e U (n)       ESC- (n)  ESC e o (n)
COMMAND SETS (DPL24CPLUS)    C-4  User's Manual Function Command Select printing style  This command allows you to combine various printing styles.  The value of n is the sum of the values of the styles you want  to combine. n= 0:Pica pitch  1:Elite pitch  4:Condensed  8:Shadow  16:Bold  32:Double width  64:Proportional Select image overlay type  This command allows you to overlay a pattern on characters. n= 1:Light dot matrix   2:Heavy dot matrix  3:Vertical bars  4:Horizontal bars  5:Slants  6:Back slants  7:Lattice Image overlay printing on/off  (on:n=1, off: n=0) ESC ! (n)            ESC e I (n)          ESC e L (n)  Horizontal Control Space  Backspace Carriage return Elite pitch (12 cpi)  Pica pitch (10 cpi)  Proportionally spaced characters on/off  (on:n=1, off: n=0) Set character pitch to (n-1)/120 inch  (1 < n < 127) Set character pitch to n/180 inch  (0 < n < 255)  SP BS CR ESC M ESC P ESC p (n)  ESC US (n)  ESC h (n)
COMMAND SETS    User's Manual  C-5 Function Command Set character offset to n/120 inch  Cancelled by CR or ESC x. (0 < n < 63) (64 < n < 127) Set character pitch to n/360 inch  (0 < n1 n2 n3 < 999)  n1, n2, and n3 are the hundreds, tens, and units digits. ESC DC1 (n)   ESC e H (n1) (n2) (n3) Vertical Control Line feed  Reverse line feed  Form feed Advance paper n/180 inch (0 < n < 255)  Reverse paper n/180 inch (0 < n < 255)  Advance paper n/360 inch  (0 < n1 n2 n3 < 999)  n1, n2, and n3 are the hundreds, tens, and units digits. Reverse paper n/360 inch  (0 < n1 n2 n3 < 999)  n1, n2, and n3 are the hundreds, tens, and units digits. Set line spacing to 1/8 inch (8 lpi)  Set line spacing to n/180 inch  (0 < n < 255) Set line spacing to 7/60 inch  Set line spacing to n/60 inch  (0 < n < 127) Set line spacing to 1/6 inch (6 lpi) or to the value set with the ESC A command. The preset line spacing command is ESC A (n). Set line spacing to n/360 inch  (0 < n1 n2 n3 < 999)  n1, n2, and n3 are the hundreds, tens, and units digits. Set line spacing to n/360 inch  (1 < n < 255)  LF LF ESC FF ESC J (n) ESC j (n) ESC e J (n1) (n2) (n3)   ESC e j (n1) (n2) (n3)   ESC 0 ESC 3 (n)  ESC 1 ESC A (n)  ESC 2    ESC e V (n1) (n2) (n3)   FS 3 (n)
COMMAND SETS (DPL24CPLUS)    C-6  User's Manual Function Command Tabulation Horizontal tab execution  Set horizontal tabs  The values of n1 to nk in this command  are the ASCII values of the print columns (at the current character width) at which tabs are to be set. (1 < n < 255) (1 < k < 255) Move to print column n (1 < n < 255)  Move dot column n/360 inch  (n = n1 + n2  256) The value below is for 136-column printers. (0 < n1 < 255) (0 < n2 < 19) (0 < n2  256 + n1 < 4895) Horizontal relative move by n/360 inch  (-999 < n1 n2 n3 < +999)  n1, n2, and n3 are the hundreds, tens, and units digits of the distance.s is a plus or minus ( + or -) sign. Vertical tab execution  Set vertical tabs  The values of n1 to nk in this command  are the ASCII values of the lines (at the current line spacing) at which tabs are to be set. (1 < n < 255) (1 < k < 64) Move to line n (1 < n < 255)   HT ESC D (n1) ... (nk) NUL     ESC HT (n) ESC $ (n1) (n2)     ESC e R (s) (n1) (n2) (n3)    VT ESC B (n1) ... (nk) NUL     ESC VT (n) Page Formatting Set right margin (0 < n < 255)  Set left margin (0 < n< 255)  Set perforation skip by n lines  (1 < n < 127) Perforation skip off Set page length to n lines  (1 < n < 127)  ESC Q (n) ESC 1 (n) ESC N (n)  ESC O ESC C (n) or ESC FF (n)
COMMAND SETS    User's Manual  C-7 Function Command Set page length to n inches  (1 < n < 22)   Set page length to n/360 inch  (n = n1  256 + n2) (0 < n1 n2 < 255) (1 < n1 < 256 + n2 < 7920) ESC C NUL (n) or ESC e C NUL (n) orESC FF NUL (n) ESC e f (n1) (n2) Character Set Control Select character set 1  Appendix E gives the character sets Select character set 2  Appendix E gives the character sets. Select international character set  n =  0:USA  1:France  2:Germany  3:United Kingdom  4:Denmark 1/Norway  5:Sweden/Finland  6:Italy  7:Spain  8:Denmark 2 Clear print buffer  Select printer  Deselect printer (ignore input)  Force most significant bit to 1  Force most significant bit to 0  Cancel control over most significant bit  ESC 7  ESC 6  ESC R (n)          CAN DC1 DC3 ESC > ESC = ESC #
COMMAND SETS (DPL24CPLUS)    C-8  User's Manual Function Command Select code table  n =  0:Code page 437   1:Code page 850   2:Code page 860   3:Code page 863   4:Code page 865   5:ISO 8859-1/ECMA 94 Select extended character by character  number  (0 < n1 n2 n3 < 664) n1, n2, and n3 are the hundreds, tens, and units digits. ESC e C (n)       ESC e E (n1) (n2) (n3) Word Processing Line justification on  Automatically center printing  Reset word processing features  ESC m ESC c ESC x Font Selection and Downloading Select font m with source and style set by n   m (bits 0 and 1: Font device selection) Bit 1  Bit 0 Selection of font0 0 1 0 1 0 Resident font Downloaded fontResident font   m (bits 2 and 3: Print quality specification Bit 3  Bit 2 Print quality 0 0 1  1 0 1 0  1 Original quality of font Letter quality (360 dpi) Correspondence quality (180 dpi) Draft quality (120 dpi)    ESC % (m) (n)
COMMAND SETS    User's Manual  C-9 Function Command  n (bit 0 to 2: Specification of font number) (1) Resident fonts n m (bit 1, 0) = 0, 0 m (bit 1, 0) = 1, 001234567Courier 10  Prestige elite 12  Draft Compressed Boldface PS Pica 10 Correspondence High-speed draft OCR-B OCR-A    (2) Downloaded fonts n =  0: Downloaded font 0   1: Downloaded font 1 Select print quality (font attributes) n =  0:Letter (360  180 dpi)  1:Correspondence (180  180 dpi)  2:Draft (120  180 dpi)   3:High-speed daft  (90  180 dpi)    4:Super high-speed draft (72×180 dpi) Select spacing mode (font attributes)  n =  0:Fixed pitch font   1:Proportional spacing font Select character pitch (n/360 inch, font  attributes) (0 < n1 < 255) (1 < n2 < 255) (n = n1  256 + n2) Ex.n = 36:  10 pitch   30:  12 pitch   24:  15 pitch   21:  17 pitch Condense/enlarge vertically (font attributes)  n =  1:Executed  0:Not executed Select point size (n/1200 inch, font attributes)  (0 < n1 < 255) (0 < n2 < 255) (n = n1  256 + n2) Ex. n =166:  10 point     ESC e q (n)     ESC e s (n)   ESC e p (n1) (n2)        ESC e A (n)   ESC  e v (n1) (n2)
COMMAND SETS (DPL24CPLUS)    C-10  User's Manual  Function Command Select character style (font attributes)  n =  0:Upright  1:Italic Select stroke weight (font attributes)  n =  249:-7 (reserved)  251:-5 (reserved)  253:-3 (light)  0:0 (medium)  3:3 (bold)  5:5 (black)  7:7 (ultrablack) Select typeface (font attributes)  n =  1:Pica  3:Courier (bitmap)   4:Nimbus Sans    5:Timeless  6:Gothic  8:Prestige  23:Boldface  130:OCR-A  131:OCR-B  134:Courier (scalable) Select font by I.D. (font attributes) ESC e i  (n)   ESC e w (n)        ESC e t (n)           ESC e F (n)  n Quality Spacing Pitch Point Typeface 1 2 3 4 9 10 32 34 128 129 130 132 133 134 140 141 142 LQLQ LQ LQ LQ LQ LQ LQ LQ LQ LQ LQ LQ LQ LQ LQ LQ FixedFixed PS Fixed Fixed Fixed Fixed Fixed PS PS PS PS PS PS Fixed Fixed Fixed 10 cpi12 cpi- 10 cpi10 cpi10 cpi10 cpi12 cpi- - - - - - 10 cpi10 cpi10 cpi12 pt10 pt12 pt12 pt12 pt 12 pt12 pt11pt 10 pt10 pt10 pt10 pt10 pt10 pt10 pt10 ptCourier (bitmap) Prestige Boldface  Pica OCR-A OCR-B Courier (bitmap) Gothic Timeless Timeless Italic Timeless Bold Nimbus Sans   Nimbus Sans  Italic Nimbus Sans  Bold Courier (scalable) Courier Bold (scalable) Courier Italic (scalable)
COMMAND SETS    User's Manual  C-11 Function Command Copy resident font to download area  m = 0:Courier 10  1:Prestige Elite 12  2:Draft  3:Compressed  4:Boldface PS  5:Pica 10  6:Correspondence  7:High-speed Draft n =  0:Downloaded font 0   1:Downloaded font 1 Create download font   m (bits 4 and 5: Specifies the quality of    characters to be registered) Bit 5 Bit 4 Font quality selection 0 1 1 1 0 1 Letter (360 dpi) Correspondence (180 dpi)Draft (120 dpi)  m (bit 0: Specifies external font number   to be registered)   ESC : NUL (m) (n)           ESC & (m) (Cs) (Ce) (data) Bit 0 Font number selection  Remarks 0  Downloaded font 0  At power on, resident font 0 is automatically downloaded. 1  Downloaded font 1  At power on, resident font 1 is automatically downloaded.   m (bits 1, 2, 3, 6, 7) Not used (don’t care)  Cs (Download start character, ASCII code)  Ce (Download end character, ASCII code) Decimal 00 < Cs, Ce < 255 Hex  00 < Cs, Ce < FF  Precaution: Ce  Cs  data (More than one byte of data   containing bit map data) (Reserved)           ESC e D (data);
COMMAND SETS (DPL24CPLUS)    C-12  User's Manual Function Command Bit Image Graphics Graphics type m graphics   Graphics type m graphics     Single-density graphics  Double-density graphics  High-speed double-density graphics  Quadruple-density graphics  360 dot per inch 24-pin graphics  ESC * (m) (n1) (n2) (data) ESC e b (m) (n1) (n2) (data) or ESC e B (m) (n1) (n2) (data) ESC K (n1) (n2) (data) ESC L (n1) (n2) (data) ESC Y (n1) (n2) (data) ESC Z (n1) (n2) (data) FS Z (n1) (n2) (data) Cut Sheet Feeder Control Feed a sheet from bin 1  Feed a sheet from bin 2  Feed a sheet from bin 3  Eject a page from the printer  Select bin 1 for following pages  Select bin 2 for following pages  Select bin 3 for following pages   ESC EM 1 ESC EM 2 ESC EM E ESC EM R / / 1 / / / / 2 / / / / E / / Initialize Printer Reset printer  Reset printer  Initialize printer  ESC @ ESC CR P ESC SUB I
COMMAND SETS    User's Manual  C-13 Function Command Bar Code Printing Print bar code  b:  Total number of parameters  R: (fixed)  c:  Type of bar code  ESC DC4 (b) R (c) (w) (h) (a) (ch1) ... (chn)  ASCII Decimal Hex Type 1 2 3 4 5 6 7 A B a 49 50 51 52 53 54 55 65 66 97 31 32 33 34 35 36 37 41 42 61 Codabar (nw-7) EAN 13 EAN 8 Code 3 of 9 Industrial 2 of 5 Interleaved 2 of 5 Matrix 2 of 5 UPC type A Code 128 UPC type A with checkdigit printing  w:  Width of narrow bar in 1/1440-inch  units h:  Height of bar code a:  Defines check characters and OCR  characters ch1 ... chn:  Bar code characters  NOTE When EAN13, UPC type A, or UPC type A with checkdigit printing is selected as the type of barcode, printing the barcode from the left (from the first dot) will cause the omission of a flag character that should by printed on the lower left or middle left of it.  Therefore, when printing these types of barcode, leave two or more spaces open from the left. See the next page for details of the Bar Code Command.
COMMAND SETS (DPL24CPLUS)    C-14  User's Manual Bar Code Printing Control ASCII  :  ESC  + DC4 + b + R  + c + w  + a  + ch1 … + chn Hexadecimal :  1B  + 14  + b + 52 + c + w  + a  + ch1 … + chn Decimal  :  27  + 20  + b + 82 + c + w  + a  + ch1 … + chn (1) Function (a)  Instructs the printing of bar codes according to the different specifications of this command. (2)  Valid range of parameters (a)  b (Specification of number of bytes) = Actual number of data + 6 (b)  R (Fixed)  ASCII  : R Hexadecimal :  82 Decimal : 52 (c)  C (Specifies the type of bar code to be printed.  No printing is done if any value other than the following is specified.) C  Type of bar code ASCII Decimal Hexadecimal1  49 31 Codabar (nw-7) 2 50  32 EAN 13 3  51 33 EAN 8 4  52  34  Code 3 of 9 5  53  35  Industrial 2 of 5 6  54  36  Interleaved 2 of 5 7  55  37  Matrix 2 of 5 A  65  41  UPC type A B 66  42 CODE 128 a 97  61 UPC type A with check character
COMMAND SETS    User's Manual  C-15 (d)  w (Specify the width of the narrow bar of the bar code to be printed in units of 1/1440.) Specify the “Logical value” to be printed (in units of 1/1440). Actual printing: The printer prints with the width given in the following table in units of 1/180 inches. w  Width of narrow bar 1 ~ 19  2 Dots (2/180 inches) 20 ~ 27  3 Dots (3/180 inches) 28 ~  4 Dots (4/180 inches)  (e)  h (Specify the height of the bar code to be printed in units of 1/1440 taking the narrow bar width as the reference.)   Height of bar code  =  (parameter w)  (parameter h) [in units    of 1/1440] Height of bar code   11 Inches Actual printing:  The printing is done with the following initial values if the bar code height is less than or equal to 24 dots taking 1 dot equal to 1/180 inches of the printing unit of the printer.   The following values are the standard heights for the respective bar code standards.  Enter the value so that the height is ≤ 23/180 if the standard is correct. Narrow bar width  EAN 13/UCP-A  EAN 8  Others 2 Dots (16/1440) 162 Dots (1296/1440)130 Dots (1040/1040) 108 Dots (864/1440) 3 Dots (24/1440) 234 Dots (1872/1440)187 Dots (1496/1040) 135 Dots (1080/1440)4 Dots (32/1440) 312 Dots (2496/1440)249 Dots (1992/1040) 162 Dots (1296/1440)  Figures in parentheses ( ) are values converted to units of 1/1440.   ..
COMMAND SETS (DPL24CPLUS)    C-16  User's Manual (f)  a (Bits 2~0: Specifications related to the check and OCR characters.) Bit Content of specification value Content of setting 0 Check character Additional specification * 1 0 Added 1 Not added 1 Specification of  OCR character printing (OCR-B is taken as the standard) 0 Printed 1 Not printed 2 Printing position of EAN, UPC flag character 0  To the left of the bar code 1 To the bottom left of the bar code  *1:  The specification becomes invalid for the following bar codes:   Codabar   … Always the non-additional code is set.   EAN, UPC  … Always the additional code is set.  *2:   The flag character is printed when Bit 1 = 0.
COMMAND SETS    User's Manual  C-17 (g)  (ch1) … (chn)   The data and the printable character set are listed below. Type of bar code  Usable character set  Data count Codabar  Numerals: 0 ~ 9 Symbols; + -, $/: Start, Stop:  A,a,B,b,C,c,D,d,  T,t,N,n,*,E,e 1 ≤ n ≤ 64  Includes Start and Stop EAN 13  Numerals: 0 ~ 9  Fixed at n=12 EAN 8  Numerals: 0 ~ 9  Fixed at n=7 Code 3 of 9  Numerals: 0 ~ 9 Alphabets: A ~ Z: Symbols:   +-,$/%SPACE Start, Stop:* Check character Additional code 1 ≤ n ≤ 63   Check character Non-additional code 1 ≤ n ≤ 64  Industrial 2 of 5  Numerals: 0 ~ 9 Interleaved  2 of 5  Numerals: 0 ~ 9 Matrix 2 of 5  Numerals: 0 ~ 9 UPC Type A  Numerals: 0 ~ 9  Fixed at n=11 UPC Type A with check character Numerals: 0 ~ 9  Fixed at n=11 Code 128 ASCII Code Start code: A, B, C Code set C: 0 ~ 9 Check character Additional code 1 ≤ n ≤ 63 Check character Non-additional code 1 ≤ n ≤ 64 Code set C: 2n
COMMAND SETS (DPL24CPLUS)    C-18  User's Manual Function Command Print Option Control Friction feed selection  Rear tractor feed selection  Front tractor feed selection  Cut sheet feed selection  Host controlled paper path control  n =  “F”  :Friction   “T” :Rear Tractor  “M” : Front Tractor Automatic paper thickness control  / / F / / / / T / / / / M / / / / S / / ESC e T (n)    ESC e P (n1) (n2) (n3) (n4) Miscellaneous Sound bell  Enable paper-out sensor  Ignore paper-out sensor  Typewriter mode on/off  (on:n=1, off: n=0) Move print head to home position  Unidirectional printing on/off  (on:n=1, off: n=0) Select CR code definition  n =  0:CR = CR only   1:CR = CR + LF Select LF code definition  n =  0:LF = LF only   1:LF = LF + CR Enter online setup mode Move print head (unit: 1/180 inch) (0 < n1 < 255) (0 < n2 < 255)  BEL ESC 9 ESC 8 ESC i (n)  ESC < ESC U (n)  ESC e r (n)   ESC e l (n)   ESC e ONLINE (data) ESC e h (n1) (n2)
COMMAND SETS    User's Manual  C-19 Factory Default Settings The following table describes the printer commands used to control options of the items that can be selected in printer setup mode. Command parameters are omitted  Item   Selectable options in setup mode   Command  Emulate  DPL24C+, XL24E, ESC/P2   Controllable in online setup mode  Font   COUR 10, PRSTG 12, COMPRSD,  BOLDFCE, PICA 10, CORRESP,  COUR-N, COUR-B, COUR-I,  TIMLS-N, TIMLS-B, TIMLS-I,  N.SAN-N, N.SAN-B, N.SAN-I. OCR-B, OCR-A, DOWNLD 0, DOWNLD 1  ESC e t  ESC e F  ESC %  Quality   LETTER, REPORT, DRAFT, HI-DRFT , SH-DRFT ESC e q  Pitch   2.5, 3, 5, 6, 10, 12, 15, 17, 18, 20 CPI or PROP SP  ESC e p  ESC e H  ESC h  ESC US  ESC M  ESC P  ESC p ESC i  ESC e s  Line space  1, 2, 3, 4, 5, 6, 7, 8, LPI   ESC e V  ESC 0 ESC 1  ESC 2  ESC 3  ESC A  Character width  NORMAL, 2 TIMES, 4 TIMES   ESC W  SO or ESC SO  (DC4) ESC u  ESC !  Character height  NORMAL, 2 TIMES, 4 TIMES   ESC V  ESC u  Underline: Factory default ( ): Cancel command
COMMAND SETS (DPL24CPLUS)    C-20  User's Manual Item   Selectable options in setup mode  Command  Attributes   NONE, ITALICS, CONDNSD, SHADOW, BOLD  ESC 4 (ESC 5)  SI or ESC SI (DC2)  ESC E (ESC F) ESC G (ESC H) ESC e i ESC !  Page length  3.0, 3.5, 4.0, 5.0, 5.5, 6.0, 7.0, 8.0, 8.5, 11.0, 11.6, 12.0, 14.0, 18.0 IN  ESC C NUL  ESC e C NUL  ESC FF NUL  ESC C  ESC e C  ESC FF  Left end   1 , 2, 3, ... , 41 COLM   Controllable in online setup mode  Top margin  1 , 2, 3, ... , 10 LINE   Controllable in online setup mode  Language   USA, UK, GERMAN, FRENCH, ITALIAN, SPANISH, SWEDISH, FINNISH, DANISH1, DANISH2, NORWEGN, PAGE437, PAGE850, PAGE860, PAGE863, PAGE865 ISO8859, ECMA94  ESC R  ESC e C  PG852, PG852-T, PG855, PG866, HUNGARY, HUNG-T, SOLV, SOLV-T, POLISH, POLSH-T, MAZOWIA, MAZOW-T, LATIN7, LATIN2, LATN2-T, KAMENIC, KAMEN-T, TURKY, TURKY-T, CYRILIC, IBM437, IBM851, ELOT928, PG-DHN, LATIN-P, ISO-LTN, LITHUA1, LITHUA2, MIK, MACEDON, ABG, ABY, PG-MAC, ELOT927, DEC-GR, GREEK 11, PG862, HBR-OLD, HBR-DEC, ISO-TUK, RUSCII, LATIN-9 , WCP1250, WCP1251, WCP1252 Uncontrollable by commands but controllable in online setup mode  Underline: Factory default ( ): Cancel command
COMMAND SETS    User's Manual  C-21 Item   Selectable options in setup mode   Command  Character set  SET 1, SET2   ESC7 ESC6  Perfora-tion skip SKIP, NO-SKIP   ESC N (ESC O)  Paper width  8.0 IN, 11.0 IN, 11.4 IN, 13.6IN, (8.0 IN is default for 80-column printer, and 13.6 IN is default for 136-column printer)  Controllable in online setup mode Zero font  NO-SLSH, SLASH   Controllable in online setup mode DC3   ENABLE, DISABLE   Controllable in online setup mode CR code  CR-ONLY, CR & LF   ESC e r  LF code   LF-ONLY, LF & CR   ESC e l  Right end wrap  WRAP, OVR-PRT   Controllable in online setup mode Paper-out  CNTONLY, DETECT, IGNORE   ESC 9 (ESC 8)  Print direction BI-DIR, UNI-DIR   ESC U  Print mode NORMAL , HISPEED , QUIET  ESC e X ESC e O High Impact DISABLE, ENABLE  ESC e z Underline: Factory default ( ): Cancel command
COMMAND SETS (IBM XL24E)    C-22  User's Manual This section describes the printer commands for the IBM Proprinter XL24E emulation.  Asterisks in the “Function” column indicate extended commands that are not supported by the original printer.  Function Command Print Mode Control Double-strike (bold) printing on  Double-strike (bold) printing off  Emphasized (shadow) printing on  Emphasized (shadow) printing off  One-line double-width characters on  One-line double-width characters off  Double-width characters on/off  (on:  n = 1, off:  n = 0) Double-height/double-width characters  n1 = 4, n2 = 0, m1 = 0, m2 = 0  m3 controls character height and line spacing: m3 Height  Spacing 0 1 2 16 17 18 32 33 34 UnchangedNormal Double UnchangedNormal Double UnchangedNormal Double Unchanged Unchanged Unchanged Single Single Single Double Double Double  m4 controls character width: m3 Height 0 1 2 UnchangedNormal Double    ESC G ESC H ESC E ESC F SO or ESC SO DC4 ESC W (n)  ESC [ @ (n1)(n2) (m1) ... (m4)  IBM PROPRINTER XL24E EMULATION
COMMAND SETS    User's Manual  C-23  Function Command Condensed characters on  Condensed and elite characters off Subscript or superscript printing on  (subscript:  n = 1, superscript:  n = 0) Subscript and superscript printing off  Underline on/off (on:  n = 1, off:  n = 0)  Overline on/off (on:  n = 1, off:  n = 0) SI or ESC SI DC2 ESC S (n)  ESC T ESC - (n) ESC_(n) Horizontal Control Space Backspace Carriage return Elite characters on Proportionally spaced characters on/off  (on:n= 1, off:  n= 0)  SP BS CR ESC: ESC P (n) Vertical Control Line feed Form feed Advance paper  n/216 inch (1 < n < 255)  Advance paper  n/180 inch (in AG mode)  (1 < n < 255) Set line spacing to 1/8 lines  Set line spacing to 7/72 inch  Set line spacing to n/216 inch  (0 < n < 255) Set line spacing to n/180 inch (in AG mode)  (0 < n < 255) Preset line spacing to n/72 inch  (1 < n < 255) Preset line spacing to n/60 inch (in AG mode)  (1 < n < 255) Set line spacing to 1/6 inch or to the value  preset by line spacing command  ESC A (n)  LF FF ESC J (n) ESC J (n)  ESC 0 ESC 1 ESC 3 (n)  ESC 3 (n)  ESC A (n)  ESC A (n)  ESC 2
COMMAND SETS (IBM XL24E)    C-24  User's Manual Function Command Change graphics line spacing base to  1/216 or 1/180 inch (for ESC J and ESC 3)  m1 = 4, m2 = 0 0 < t1 < 255, 0 < t2 < 255, t3 = 0 t4 = 180 or 216 ESC [ \ (m1) (m2) (t1) ... (t4) Tabulation Horizontal tab execution  Set horizontal tabs  The values of n1 to nk in this command  are the ASCII values of the print columns (at the current character width) at which tabs are to be set.  (1 < n< 255) (1 < k < 28) Clear all horizontal tabs  Move print position right by n/120 inch  (0 < n1, n2 < 255) (n = n1 + n2  256) Vertical tab execution  Set vertical tabs  The values of n1 to nk in this command  are the ASCII values of the lines (at the current line spacing) at which tabs are to be set.  (1 < n < 255) (1 < k < 64) Clear all vertical tabs  Reset tabs to default values  HT ESC D (n1)... (nk) NUL    ESC D NUL ESC d (n1)(n2)  VT ESC B (n1)... (nk) NUL    ESC B NUL ESC R Page Formatting Set left margin at column n and right  margin at column m (0 < n, m < 255) Set perforation skip by n lines  (1 < n < 255) Perforation skip off  Set page length to n lines (1 < n < 255)  Set page length to n inches (1 < n < 22)  Set top of form  ESC X (n) (m)  ESC N (n)  ESC O ESC C (n) ESC C NUL (n) ESC 4
COMMAND SETS    User's Manual  C-25 Function Command Character Set Control Select character set 1  Select character set 2  Print n1+ n2  256 characters from all-  character set  (chars.:  codes of characters to print, 0 < chars. < 255) Print a character from all-character set  (char.:  a code of character to print, 0 < char. < 255) Select code page table n  (0 < n1, n2 < 255) (n = n1+ n2  256)  c1c2Code page ID 0133330 18182929597Ignore command Code page 437 Code page 850 Code page 860 Code page 863 Code page 865  Clear input buffer  Select printer  Deselect printer (ignore input)  ESC 7 ESC 6 ESC \ (n1)(n2) (chars.)   ESC  ^ (char.)   ESC [ T (n1)(n2) 0 0 (c1)(c2)         CAN DC1 ESC Q #
COMMAND SETS (IBM XL24E)    C-26  User's Manual Function Command Downloading Select resident or downloaded font  Ex.n = 0:Resident Draft  2:Resident Courier  4:Downloaded Draft  6:Downloaded Courier Create download font  ESC I (n)    ESC = (n1) (n2) ID (m1) (m2) (data) Bit Image Graphics Single-density graphics  Double-density graphics  High-speed double-density graphics  Quadruple-density graphics  High-resolution graphics   Select graphics mode (in AG mode only)  ESC K (n1)(n2) (data) ESC L (n1)(n2) (data) ESC Y (n1)(n2) (data) ESC Z (n1)(n2) (data) ESC [ g (n1)(n2) (m) (data) ESC * (m) (c1) (c2) (data) Cut Sheet Feeder Control Feed a sheet from bin 1  Feed a sheet from bin 2 Feed a sheet from bin 3 Eject a page from the printer  Select bin 1 for following pages  Select bin 2 for following pages  Select bin 3 for following pages  Change bins at next page  ESC EM 1 ESC EM 2 ESC EM E ESC EM R / / 1 / /  / / 2 / /  / / E / /  / / C / /  Print Option Control Friction feed selection  Rear tractor feed selection  Front tractor feed selection  Cut sheet feed selection Host controlled paper path control  n =  “F”  :Friction   “T” :Rear Tractor  “M” : Front Tractor Automatic paper thickness control  / / F / /  / / T / /  / / M / /  / / S / /  ESC e T (n)    ESC e P (n1) (n2) (n3) (n4)
COMMAND SETS    User's Manual  C-27  Function Command Miscellaneous Sound the bell  Unidirectional printing on/off  (on:n= 1, off:n= 0) Add a carriage return to all line feeds  (on:n= 1, off:n= 0) Printer offline  Enter online setup mode  Select default settings  BEL ESC U (n)  ESC 5 (n)  ESC j ESC e ONLINE (data)ESC [ K (n1)(n2) (i) (ID) (p1)(p2) Bar Code Printing Print bar code  b:  Total number of parameters  R: (fixed)  c:  Type of bar code  w:  Width of narrow bar in 1/1440-inch  units h:  Height of bar code a:  Defines check characters and OCR  characters ch1 ... chn:  Bar code characters  NOTE Please refer to the command specification of DPL24CPLUS for details.  ESC DC4 (b) R (c) (w) (h) (a) (ch1) ... (chn)
COMMAND SETS (ESC/P2)    C-28  User's Manual This section describes the printer commands for the Epson ESC/P2 emulation.  Asterisks in the “Function” column indicate extended commands that are not supported by the original printer.  Function Command Print Mode Control Double-strike (bold) printing on  Double-strike (bold) printing off  Emphasized (shadow) printing on  Emphasized (shadow) printing off  Italic printing on  Italic printing off  Select character style  n = 0: Normal  1: Outlined  2: Shaded   3: Outlined and shadowed One-line double-width characters on  One-line double-width characters off  Double-width characters on/off  (on: n= 1, off: n= 0) Double-height characters on/off  (on: n= 1, off: n= 0) Condensed characters on  Condensed characters off  Subscript or superscript printing on  (subscript: n= 1, superscript: n= 0) Subscript and superscript printing off  Underline on/off  (on: n= 1, off: n= 0)  ESC G ESC H ESC E ESC F ESC 4 ESC 5 ESC q (n)     SO or ESC SO DC4 ESC W (n)  ESC w (n)  SI or  ESC SI DC2 ESC S (n)  ESC T ESC - (n)    EPSON ESC/P2 EMULATION
COMMAND SETS    User's Manual  C-29 Function Command Select line  n1 = 3, n2 = 0, d1 = 1  d2 = 0:Ignore command  1:Underline  2:Strike through  3:Overscore d3 = 0 or 4:Cancel line selection   1:Single line   2 or 3:Double line   5:Single-dotted line   6 or 7:Double-dotted line Select printing style  This command allows you to combine various printing styles.  The value of n is the sum of the values of the styles you want to combine. n =  0:Pica pitch  1:Elite pitch  2:Proportional spacing  4:Condensed  8:Shadow  16:Bold  32:Double-width  64:Italics  128:Underline ESC ( - (n1)(n2) (d1) (d2) (d3)          ESC ! (n) Horizontal Control Space Backspace Carriage return Set elite pitch Set pica pitch Set 15 CPI Proportionally spaced characters on/off  (on: n = 1, off: n = 0) Set inter-character space to n/120 inch (for  draft) or n/180 inch (for letter and proportional) (0 < n < 127)  SP BS CR ESC M ESC P ESC g ESC p (n)  ESC SP (n)
COMMAND SETS (ESC/P2)    C-30  User's Manual Function Command Set character pitch to (n1+ n2  256)/360 inch  (0 < n1 < 255) (0 < n2 < 4) Select character pitch (specify unit of pitch)  n1 = 1, n2 = 0 d = 10 to 19:  10/3600 inch = 1/360 inch d = 20 to 29:  20/3600 inch = 1/180 inch d = 30 to 39:  30/3600 inch = 1/120 inch d = 40 to 49:  40/3600 inch = 1/90 inch d = 50 to 59:  50/3600 inch = 1/72 inch d = 60 to 69:  60/3600 inch = 1/60 inch ESC c (n1)(n2)  ESC ( U (n1)(n2) (d)  Vertical Control Line feed Form feed Advance paper n/180 inch (1 < n < 255)  Set line spacing to 1/8  inch  Set line spacing to n/180 inch (0 < n <  255)  Set line spacing to n/60 inch (0 < n < 127)  Set line spacing to 1/6 inch  Set line spacing to n/360 inch (0 < n < 255)  LF FF ESC J (n) ESC 0 ESC 3 (n) ESC A (n) ESC 2 ESC + (n) Tabulation Horizontal tab execution Set horizontal tabs  The values of n1 to nk in this  command are the ASCII values of the print columns (at the current character width) at which tabs are to be set. (1 < n < 255) (1 < k < 32) Move print position n/120 inch (for draft)(*1)  or n/180 inch (for letter)(*1) right from left margin (n = n1+ n2  256) Move print position n/120(*1) inch (for draft)  Or n/180(*1) inch (for letter) left or right from the current position (n = n1+ n2  256) Vertical tab execution  HT ESC D (n1)... (nk) NUL     ESC $ (n1)(n2)   ESC \ (n1)(n2)    VT
COMMAND SETS    User's Manual  C-31 Function Command Set vertical tabs  The values of n1 to nk in this  command are the ASCII values of the lines (at the current line spacing) at which tabs are to be set. (1 < n < 255) (1 < k < 16) Move to dot line (d1 + d2  256)/360(*1) inch  n1 = 2, n2 = 0  (0 < d1 < 255) (0 < d2 < 127) Vertical relative move by (d1 + d2  256)/360(*1)  Inch  n1 = 2, n2 = 0 (0 < d1 < 255) (0 < d2 < 127) -32768 < d1 + d2 256  32768 ESC B (n1)... (nk) NUL     ESC ( V (n1) (n2) (d1) (d2)  ESC ( v (n1) (n2) (d1) (d2) Page Formatting Set right margin to column n  (1 < n < 255) Set left margin to column n  (0 < n < 255) Set top and bottom margins from top of page  n1 = 4, n2 = 0   Top margin = (t1 + t2  256)/360(*1) inch   (0 < t1 < 255) (0 < t2 < 127)  Bottom margin = (b1+b2  256)/360(*1) inch   (0 < b1< 255)   (0 < b2 < 127) Set perforation skip by n lines  (1 < n < 127) Perforation skip off  Set page length to n lines (1 < n < 127)  Set page length to n inches (1 < n < 22)  Set page length to (d1 + d2  256)/360(*1) inch  n1 = 2, n2 = 0  (0 < d1< 255) (0 < d2 < 127)  ESC Q (n)  ESC  l (n)  ESC ( c (n1) (n2) (t1) (t2) (b1) (b2)      ESC N (n)  ESC O ESC C (n) ESC C NUL (n) ESC ( C (n1) (n2) (d1) (d2) *1  The value depends on the pitch set by the ESC (U command.   The default is 1/360 inch.
COMMAND SETS (ESC/P2)    C-32  User's Manual Function Command Character Set Control Select character set 1  Select character set 2 Select character set table  n =  0:Italics character set   1:Graphics character set   2:Downloaded character set   3:Graphics character set Select international character set  n =  0:USA  1:France  2:Germany  3:United Kingdom  4:Denmark 1  5:Sweden  6:Italy  7:Spanish 1  8:Japan  9:Norway  10:Denmark 2  11:Spanish 2  12:Latin America  13:Korea  64:Legal  ESC 7 ESC 6 ESC t (n)     ESC R (n)
COMMAND SETS    User's Manual  C-33 Function Command Assign a character set to active character set  number 0 to 3  n1 = 3, n2 = 0 d1 = 0:Active character set number 0   1:Active character set number 1   2:Active character set number 2   3:Active character set number 3 d2 = 0:Italic    1:PC 437 (USA)    3:PC 850 (Multilingual)   7:PC 860 (Portugal)   8:PC 863 (Canada-French)   9:PC 865 (Norway) d3 = 0 Print n1+ n2  256 characters from all-  character set  (0 < n1 < 255) (0 < n2 < 127) (0 < n1 + n2  256 < 255) (0 character codes < 254) Clear input buffer Delete a character Force most significant bit to 1 Force most significant bit to 0 Cancel control over most significant bit ESC ( t (n1) (n2) (d1) (d2) (d3)             ESC ( ^ (n1)(n2) (character codes)    CAN DEL ESC > ESC = ESC # Font Selection and Downloading Select font  n =  0:Resident character set   1:Downloaded character set Select letter or draft quality  n =  0:Draft  1:Letter  ESC % (n)   ESC x (n)
COMMAND SETS (ESC/P2)    C-34  User's Manual Function Command Select type style  Bitmap font: n =  0:Courier  1:Courier  2:Courier  3:Prestige  4:Courier  5:OCR-B  6:OCR-A  7:Courier  8:Courier  9:Courier  Scalable font: n =  0:Timeless  1:Nimbus Sans   2:Courier  3:Timeless  4:Timeless  5:Timeless  6:Timeless  7:Timeless  8:Timeless  9:Timeless Set scalable font mode   m sets character pitch. m = 0:Keep previous pitch   1:Set proportional space mode m > 5:Select character pitch   (m/360 inch)     (Reset proportional space mode)  n1 and n2 set point size of font. Point size = (n1 + n2  256)  0.5 point (0 < n1 < 255) (0 < n2 < 127) Copy resident character set to download area  Create download font  ESC k (n)                      ESC X m (n1)(n2)          ESC : NUL(n)(s) ESC & NUL (n1)(n2) (d0) (d1) (d2) (data) *  Indicates extended commands not supported by the original printer.
COMMAND SETS    User's Manual  C-35 Function Command Bit Image Graphics Graphics type m graphics   Bit image mode definition  Single-density graphics  Double-density graphics  High-speed double-density graphics  Quadruple-density graphics  Select raster image graphics  n1 = 1, n2 = 0 d= 1:  Raster image graphics mode Print raster image graphics  ESC * (m) (n1)(n2) (data) ESC ? (s) (n) ESC K (n1)(n2) (data) ESC L (n1)(n2) (data) ESC Y (n1)(n2) (data) ESC Z (n1)(n2) (data) ESC ( G (n1)(n2) (d)   ESC . (c)(v) (h) (m) (n1)(n2) (data) Cut Sheet Feeder Control Feed a sheet from bin 1  Feed a sheet from bin 2  Feed a sheet from bin 3  Eject a page from the printer  Select bin 1 for following pages   Select bin 2 for following pages   Select bin 3 for following pages   Change bins at next page   ESC EM 1 ESC EM 2 ESC EM E ESC EM R / / 1 / /  / / 2 / /  / / E / /  / / C / /  Print Option Control Friction feed selection   Rear tractor feed selection   Front tractor feed selection   Cut sheet feed selection  Host controlled paper path control  n =  “F”  :Friction   “T” :Rear Tractor  “M” : Front Tractor Automatic paper thickness control  / / F / / / / T / / / / M / / / / S / / ESC e T (n)    ESC e P (n1) (n2) (n3) (n4)
COMMAND SETS (ESC/P2)    C-36  User's Manual  Function Command Miscellaneous Sound the bell  Move print head to home position  Unidirectional printing on/off  (on:n = 1, off:n = 0) Initialize printer  Enter online setup mode   BEL ESC < ESC U (n)  ESC @ ESC e ONLINE (data) Bar Code Printing Print bar code  b:  Total number of parameters  R: (fixed)  c:  Type of bar code  w:  Width of narrow bar in 1/1440-inch  units h:  Height of bar code a:  Defines check characters and OCR  characters ch1 ... chn:  Bar code characters  NOTE Please refer to the command specification of DPL24CPLUS for details.  ESC DC4 (b) R (c) (w) (h) (a) (ch1) ... (chn)
  User's Manual  D-1 D  APPENDIX D  INTERFACE INFORMATION INTERFACE INFORMATION This printer can communicate with a computer through  a Centronics parallel interface, a RS-232C  serial interface, a USB interface, or a LAN interface.  You can specify the interface selection mode so that the printer uses which interface or it can automatically select the interface from which it first receives data. This appendix provides information you may need for wiring your own interface cables or for programming computer-to-printer communications. Most users do not need the information in this appendix.  To simply connect your printer to your computer, follow the instructions in Chapter 2. This parallel interface can operate in the following two modes:  Unidirectional (forward channel) mode or conventional mode:  This printer supports a conventional Centronics interface.  Bidirectional (forward/reverse channel) mode or nibble mode:  This printer supports a bidirectional communication per Nibble mode of the IEEE 1284 Standard. The cable connector at the printer side should be a shielded, Amphenol DDK 57FE-30360 or equivalent. The connector pin assignments are given in the following tables by modes.  In the tables:  “Input” denotes a signal from the computer to the printer.  “Output” denotes a signal from the printer to the computer.  The return lines specified in the second column represent twisted pairs, with one side  connected to signal ground.  The standard signal levels are 0.0 to +0.4 V (low), and +2.4 to +5.0 V (high). PARALLEL INTERFACE
INTERFACE INFORMATION     D-2  User's Manual Compatible Mode  Pin No.  ReturnPin No. Signal Name Direction Description 1 19 Data Strobe (DSTB) Input  This signal is a strobe pulse for reading data (Data 1 to 8).  The printer reads data when this signal is low. The pulse width must be 1 s or more at the receiving terminal. 2-9  20-27  Data 1 to 8  Input  Data 8 (pin 9) is the most significant bit; however, this pin is not used in 7-bit ASCII communications. Logical 1 signals must go high at least 1 s before the falling edge of the  Data Strobe signal and must stay high for at least 1 s after the rising edge. 10 28 Acknowledge(ACK) Output  This pulse signal indicates that the printer has received data and is ready to accept the next set of data. This signal is also sent when the printer is switched from offline to online. 11  29  Busy  Output  Data cannot be received when this signal is high.  This signal is high during data entry, when the printer is offline, when the buffer is full, or when an error occurs. 12 30 Paper Empty (PE) Output  This signal is high when the printer is out of paper.
INTERFACE INFORMATION    User's Manual  D-3 Pin No.  ReturnPin No. Signal Name Direction Description 13   Select (SLCT) Output  This signal is high when the printer is online. 14   Auto Feed XT Input Not used 15     No connection 16   Signal Ground  Logic ground level (0 V) 17   Frame Ground  Printer chassis ground line.  FG and SG are connected.18   +5 V  Output  +5 V source (up to 300 mA) 19- 30  Signal Ground  Twisted pair return lines 31   Input Prime (INPRM)   If this signal is low for more (INPRM) than 50 s, the printer is reset to the initial condition and is placed online. 32   Fault  Output  This signal is low when the printer is offline, paper is out, or when there is a printer error. 33   Signal Ground  Logic ground level (0 V) 34     No connection 35   +5 VR  Output  Pulled up to +5 V through a 3.3 k resistor 36   SLCT-IN Input  Not used
INTERFACE INFORMATION     D-4  User's Manual Nibble Mode Pin numbers 2 to 9, 15 to 31, and 33 to 35 are the same as the conventional mode. Pin No.  ReturnPin No. Signal Name Direction Description 1  19  Host Clock  Input  This signal is set high when the host requests the reverse data transfer phase (nibble mode). 10  28  Printer Clock  Output  Reverse data transfer phase:  This signal goes high when data being sent to the host is established. Reverse idle phase: This signal is set low then goes high to interrupt the host, indicating that data is available. 11  29  Printer Busy  Output  Reverse data transfer phase: Data bit 3, data bit 7, then forward path (host to printer) busy status 12  30  Ack Data Req Output  Reverse data transfer phase: Data bit 2, then data bit 6 Reverse idle phase: This signal is set high until the host requests data and, after that, follows the Data Available signal. 13   X Flag  Output  Reverse data transfer phase: Data bit 1, then data bit 5
INTERFACE INFORMATION    User's Manual  D-5 Pin No.  ReturnPin No. Signal Name Direction Description 14   Host Busy  Input  Reverse data transfer phase: This signal is set low when the host can receive data, and goes high when the host has received data.  Following a reverse data transfer, the interface enters the reverse idle phase when the Host Busy signal goes low and the printer has no data. Reverse idle phase: This signal goes high when the Printer Clock signal goes low so that the interface re-enters the reverse data transfer phase.  If it goes high with the 1284 Active signal low, the 1284 idle phase is aborted and the interface returns to the compatibility mode. 32   Data Available Output  Reverse data transfer phase: This signal is set low when the printer is ready to send data to the host.  During the data transfer, it is used as data bit 0 (LSB), then data bit 4. Reverse idle phase: This signal is used to indicate that data is available. 36   1284 Active  Input  This signal goes high to cause the printer to enter the reverse data transfer phase (nibble mode).
INTERFACE INFORMATION     D-6  User's Manual Data Transmission Timing In unidirectional mode (conventional Centronics interface), this printer guarantees the received data when the Data and Data Strobe signals from the computer have the following timing with respect to the Busy and Acknowledge signals from the printer.   T1, T2, T3 > 1 s T4 < 1 s 0 s < T5 < 3 s 2 s < T6 < 6 s  In bidirectional mode (nibblemode), this printer can send data to the computer.  Data is sent in units of four bits (nibble) using four output signal lines as data paths.  The following outlines one byte of data sent during reverse data transfer phase in nibble mode.
INTERFACE INFORMATION    User's Manual  D-7 RS-232C is the standard serial interface for data terminal equipment. The cable connector at the printer side should be a D-subminiature Cannon or Cinch DB-25P male connector or equivalent that conforms to EIA standards. The table that follows shows the pin assignments commonly used by most computers.  In the table:   “Input” denotes a signal from the computer to the printer.   “Output” denotes a signal from the printer to the computer.  The signal level for mark state (logical 1) is -3 V or lower; for space state (logical 0), it is +3 V or higher.  Pin No.  Signal Name Direction Description 1 FG   Frame Ground 2  TD  Output  This pin carries information from the printer to the computer. 3  RD  Input  Received Data.  This pin carries information from the computer to the printer. 4  RTS  Output  Request To Send.  Spaces are sent when the printer is ready to transmit data. 5  CTS  Input  Clear To Send.  Spaces are sent when the computer is ready to receive data. 6  DSR Input  Data Set Ready.  Spaces are sent when the computer has been powered on and is ready to receive or transmit data. 7 SG   Signal Ground (common return) 8  CD  Input  Carrier Detect.  Spaces are sent when the computer allows the printer to receive data. 11  RC  Output  Reverse Channel.  This signal is used instead of the DTR signal in the RC protocol.  Spaces are sent when the printer is ready to receive or transmit data. 20  DTR Output  Data Terminal Ready.  Spaces are sent when the printer has been powered on and is ready to receive or transmit data.  SERIAL INTERFACE
INTERFACE INFORMATION     D-8  User's Manual Serial Options The serial options for the computer and the printer must match.  Use the printer control panel, the computer operating system, or your software to change options specified as “selectable.” Transmission mode:  Asynchronous, full duplex, or half duplex (selectable) Speed:  150, 300, 600, 1200, 2400, 4800, 9600, or 19200 baud (selectable) Data bits:  7 or 8 bits (selectable) Parity bit:  Odd, even, mark, space, or none (selectable) Start bit:  1 bit Stop bit:  1 or 2 bits (selectable) Protocol:  XON/XOFF (DC1/DC3), DTR (Data Terminal Ready), or RC (Reverse Channel) (selectable) Buffer size:  256, 2K, 8K, 24K, 32K, 96K, or 128K bytes (selectable) Cable Wiring This printer allows two types of serial communication control:  DSR-enabled and DSR-disabled.  The type of control required is determined by your computer requirements.  The type of control also affects the way the interface cable is wired.  To determine whether you need DSR-enabled control or DSR-disabled control, use the printer HARDWRE function (see Chapter 5). DSR-disabled control offers simpler cabling and communication than DSR-enabled control.  DSR-disabled control can be used to interface with an IBM PC and most other personal computers.  With DSR-disabled control, the input control signals DSR, CTS, and CD are always considered high, regardless of their actual states.  Therefore, no wire connection for these pins is required.  The following figure shows the wiring required for connection to an IBM PC.
INTERFACE INFORMATION    User's Manual  D-9   DSR-enabled control enables communication using an RS-232C interface.  The CTS and DSR input control signals are enabled; CD is ignored.  DSR must be high when the printer receives data.  If the printer has data to be transmitted to the computer, the printer transmits the data when both DSR and CTS are high. When using DSR-enabled control, use a straight-through cable to connect to a DCE (data communications equipment) device.  Use a null-modem cable to connect to a DTE (data terminal equipment) device, as shown below.
INTERFACE INFORMATION     D-10  User's Manual Serial Protocols A protocol is a set of instructions that control the way data is transmitted between devices such as a computer and printer.  The protocol ensures that the computer does not send information to the printer faster than the information can be processed.  By telling the computer when the printer can receive data, the protocol prevents the printer s buffer from overflowing. This printer offers a choice of four different protocols for connection to a variety of computers:  XON/XOFF, DTR, and RC.  If you computer documentation does not recommend a particular protocol, try DTR.  The following table describes the three protocols. Protocol Description XON/XOFF(DC1/DC3) When the printer is ready to receive data, it sends the XON (DC1) code (hex 11).  When fewer than 255 bytes of space remain in the buffer (or when the printer is taken offline), the printer sends the XOFF (DC3) code (hex 13).  (When the input buffer is configured for 256 bytes, the buffer limit is reduced from 255 bytes to 63 bytes.)  The computer must stop transmitting data within 255 (63)  characters of receiving the XOFF code, or information may be lost.  If paper runs out, the printer sends an NAK code (hex 15). DTR  DTR is a hardware protocol; that is, the DTR signal on interface cable pin 20 is used to control the flow of data rather than transmission of a character code.  When the printer is ready to receive data, pin 20 is high.  When fewer than 255 (63) bytes of space remain in the buffer (or when the printer is taken offline), pin 20 is low.  The computer must stop transmitting data within 255 (63) characters of DTR being low, or information may be lost.  RC  The RC protocol is the same as the DTR protocol, except that the Reverse Channel signal (pin 11) is used instead of the Data Terminal Ready signal (pin 20).
INTERFACE INFORMATION    User's Manual  D-11 Cable This printer supports the USB 2.0 Full speed specification.  To connect to the host, use USB 2.0-compliant INF cables (5 meters  (196 inch) or shorter).  (Use the shielded cables.) Connector pin alignment No. Signal line name  Function 1 VBUS Power supply 2 D- Data transfer 3 D+ Data transfer 4 GND Signal ground Shell Shield   - Connector specification Printer side  Cable side  Type B receptacle (female) Upstream port Type B plug (male)  Specification -  Basic specification  USB interface compliant  Note   It does not guarantee all operations on hosts. -  Power control  Self-power device -  Transmission mode  Full speed (Maximum 12 Mbps     +0.25%) USB INTERFACE
INTERFACE INFORMATION     D-12  User's Manual Cable This printer supports the 10Base-T and 100Base-TX cables.  Connector pin alignment  No. Signal line name DIR Function 1  TXO+  NIC-HUB  Transmit data + 2 TXO- NIC-HUB Transmit data - 3  RXI+  HUB-NIC  Receive data + 4     5     6 RXI- HUB-NIC Receive data - 7     8       Green LED:   100Mbps Amber LED:  Link/Act  Specification - Ethernet specifications    Standard:  IEEE802.3 10BASE-T,       IEEE802.3u 100BASE-TX     Speed:  100Mbps/10Mbps         Auto negotiation    Duplex:  Full/Half       Auto negotiation    MDI/MID-X:  Auto negotiation -  Internet protocol specifications    Link layer:  ARP     Internet layer:  IPv4, ICMPv4     Transport layer:  TCP, UDP     Application layer:  #9100 RAW, LPD, FTP,       HTTP, SNMP, DHCP  Note   It does not guarantee all operations on hosts.  LAN INTERFACE  Green LED  Amber LED
  User's Manual  E-1 E  APPENDIX E  CHARACTER SETS CHARACTER SETS Below are character sets 1 and 2 of Code Page 437, available in the DPL24C PLUS command set and the IBM Proprinter XL24E emulation.  Characters enclosed in boxes differ for sets 1 and 2. Characters in set 2 also vary with the national character set. Code Page 437 is for the USA character set. Code Page 437 Character Set 1   Code Page 437 Character Set 2  CHARACTER SETS 1 AND 2 (DPL24C PLUS AND IBM XL24E EMULATION)
CHARACTER SETS    E-2  User's Manual  The following shows character sets available in the Epson ESC/P2 emulation.  Characters differ in codes 128 to 255 (hex 80 to FF).  Italic Character Set   Graphics Character Set 1     ITALIC AND GRAPHICS CHARACTER SETS (ESC/P2 EMULATION)
CHARACTER SETS    User's Manual  E-3 Graphics Character Set 2
CHARACTER SETS    E-4  User's Manual Below are the 52 national character sets available for all emulations of this printer.  These character sets support different characters and symbols specific to different languages.  Note that these tables are for Courier 10, a resident font, and that some national character sets do not have some characters and symbols whose use depends on resident fonts.  For details, see the table at the end of this appendix. When the following character sets are used with the Epson ESC/P2 emulation, the printing of FFh code characters is not supported. ECMA94, ISO8859, ISO-LTN, ISO-TUK, CYRILIC, LATIN-9     NATIONAL CHARACTER SETS (ALL EMULATIONS) UK (British English)  SWEDISH (Swedish) GERMAN (German)  ISO8859/ECMA94 (ISO 8859-1/ECMA94)
CHARACTER SETS    User's Manual  E-5                         PAGE437/USA (Code Page 437/USA) PAGE852/PG852-T (Code Page 852)  PAGE850 (Code Page 850(Multilingual)) PAGE855 (Code Page 855)
CHARACTER SETS    E-6  User's Manual                         PAGE860 (Code Page 860(Portugal))  PAGE865 (Code Page 865(Nordic))  PAGE863 (Code Page 863(Canada-French))  PAGE866 (Code Page 866(Cyrillic))
CHARACTER SETS    User's Manual  E-7                               HUNGARY/HUNG-T (Hungarian)  POLISH/POLSH-T (Polish)  SLOV/SLOV-T (Slovenian)  MAZOWIA/MAZOW-T (Mazowian)
CHARACTER SETS    E-8  User's Manual                         LATIN2/LATN2-T (Latin2) TURKY/TURKY-T (Turkish) KAMENIC/KAMEN-T (Kamenicky)  CYRILIC (Cyrillic)
CHARACTER SETS    User's Manual  E-9                         IBM437 (IBM 437)  ELOT928 (ELOT 928)  IBM851 (IBM 851)  PG-DHN (Code Page DHN)
CHARACTER SETS    E-10  User's Manual                         LATIN-P (Latin Polish)  LITHUA1 (Lithuanian 1)  ISO-LTN (ISO Latin)  LITHUA2 (Lithuanian 2)
CHARACTER SETS    User's Manual  E-11                         MACEDON (Macedonian)  PG-MAC MIK ELOT 927
CHARACTER SETS    E-12  User's Manual                        ABG DEC GR  ABY HBR-OLD
CHARACTER SETS    User's Manual  E-13                         PAGE 862 (Code Page 862)  GREEK 11 HBR-DEC ISO-TUK
CHARACTER SETS    E-14  User's Manual            The following character sets differ from those of Code Page 437 (USA), available in the DPL24C PLUS command set and the IBM Proprinter XL24E emulation.                 NATIONAL CHARACTER SETS (DPL24C PLUS AND IBM XL24E EMULATION) RUSCII LATIN-9  FRENCH (French)  ITALIAN (Italian)
CHARACTER SETS    User's Manual  E-15                         SPANISH (Spanish)  FINNISH (Finnish) DANISH1/NORWEGN (Danish1/Norwegian) DANISH2 (Danish2)
CHARACTER SETS    E-16  User's Manual The following character sets differ from the graphics character sets available in the Epson ESC/P2 emulation.                           NATIONAL CHARACTER SETS (ESC/P2 EMULATION) DANISH1 (Danish1)  SPANSH1 (Spanish1) ITALIAN (Italian)  SPANSH2 (Spanish2)
CHARACTER SETS    User's Manual  E-17                         JAPAN (Japanese)   LATIN A (Latin American)   NORWEGN (Norwegian)  FRENCH (French)
CHARACTER SETS    E-18  User's Manual                         DANISH2 (Danish2)  KOREA LEGAL
CHARACTER SETS    User's Manual  E-19                           WCP1250 (Windows –1250)  WCP1252 (Windows –1252)   WCP1251 (Windows –1251)
CHARACTER SETS    E-20  User's Manual In all emulations, this printer supports 52 national character sets for characters and symbols specific to different languages.  Some national character sets, however, do not have some characters and symbols and may not be usable, depending on resident fonts.  The following tables show which of the resident fonts are supported for each national character set:  Resident font National  character set  Name in setup menuUSA *  USA      United Kingdom UK       German GERMAN      Swedish SWEDISH      ISO 8859-1  ISO8859       ECMA94 ECMA94      Code Page 437*  PAGE437      Code Page 850  PAGE850       Code Page 852  PAGE852       Code two-pass  PAGE852-T      Code Page 855  PAGE855           Code Page 860  PAGE860       Code Page 863  PAGE863       Code Page 865  PAGE865       Code Page 866  PAGE866           (Continued on the next page) *  USA is the same as Code Page 437. **  Upright, italic, and bold available  :  Supported   NATIONAL CHARACTER SETS AND SUPPORTED RESIDENT FONTS (ALL EMULATIONS)
CHARACTER SETS    User's Manual  E-21 Resident font National  character set  Name in setup menuHungarian HUNGARY       Hungarian two-pass HUNG-T        Slovenian SLOV      Slovenian two-pass SLOV-T        Polish POLISH       Polish two-pass POLISH-T        Mazowian MAZOWIA       Mazowian two-pass MAZOW-T       Latin 2  LATIN2        Latin 2 two-pass LATIN2-T        Kamenicky KAMENIC       Kamenicky two-pass KAMEN-T        Turkish TURKY       Turkish two-pass TURKY-T        Cyrillic CYRILIC         IBM 437  IBM437          IBM 851  IBM851          ELOT 928  ELOT928          Code Page DHN PG-DHN        Latin Polish  LATIN-P        ISO Latin  ISO-LTN        (Continued on the next page) **  Upright, italic, and bold available  :  Supported
CHARACTER SETS    E-22  User's Manual Resident font National  character set  Name in setup menuLithuanian 1  LITHUA1          Lithuanian 2  LITHUA2          MIK MIK         Macedonian MACEDON         ABG ABG         ABY ABY         DEC Greek  DEC GR          ELOT 927  ELOT 927          GREEK 11  GREEK 11          Code Page 862  PG 862        Hebrew DEC  HBR-DEC        Hebrew Old  HBR-OLD        Code Page MAC PG-MAC          ISO Turkish  ISO-TUK       RUSCII RUSCII      ISO8859-15 LATIN-9      Windows Code Page 1250 WCP1250        Windows Code Page 1251 WCP1251        Windows Code Page 1252 WCP1252        **  Upright, italic, and bold available  :  Supported
  User's Manual  F-1 F  APPENDIX F  RESIDENT FONTS RESIDENT FONTS This appendix provides print samples of  the printer's nineteen resident fonts.     COURIER 10 PRESTIGE ELITE 12 DRAFT 12 COMPRESSED PICA 10 CORRESPONDENCE 10 HIGH-SPEED DRAFT 12 BOLDFACE PS OCR-B 10 OCR-A 10
RESIDENT FONTS    F-2  User's Manual    COURIER (SCALABLE) Normal Bold Italic Normal Bold Italic Normal Bold Italic NIMBUS SANS  (SCALABLE) TIMELESS (SCALABLE)
  User's Manual  IN-1 INDEX INDEXA Adjustments   left margin ..................... 3-10, 3-12, 3-16, 5-18   left print start position ............................... 5-35   top-of-form .................... 3-22,  5-19, 5-32, 5-33  paper thickness........................................... 3-8 AMOUNT ...................................................... 5-49 ATTRIB ......................................................... 5-17 B Bidirectional printing ............................. 5-28, 5-56 Boldface ............................................ 1-1, 4-5, F-1 BUFFER ............................... QR-2, 4-1, 5-28, B-1 BUZZER ........................................................ 5-28 C Cables   LAN ................................... 1-3, 2-21, 8-1, A-1   parallel interface .............................. 2-20, 5-29   serial interface ................ 2-20, 5-12, 5-29, 5-30   USB ....................................... 2-21, 5-29, D-11 Centronics ..................................... 2-20,  5-29,  D-1 Character .............................. 5-15, 5-16, 5-20, E-1 Cleaning ..........................................................  6-1 Continuous forms  loading ............................................. 3-16, 3-19  placement ................................................. 3-15  tearing off ................................................. 3-20  unloading .................................................. 3-19 Control panel .................. QR-1, 2-14, 3-2, 4-1, 6-8 Cut sheet feeder   installing ...................................... 3-6, 8-1, A-1   loadin g ...................................................... 3-12 D Default .................................................. 5-10,  5-51 Demo pattern .................................................. 2-19 Diagnostic functions ............................. 5-52, 7-10 Download ........................................ B-1, B-4, C-8 DPL24C PLUS .............................................. 5-14 DRAFT .................................................. 5-15, B-2 E Eject .................................................... QR-2,  3-14 Emulation .............................................  2-22,  5-14 Envelope ....................................................... 3-23 Epson ESC/P2 ................................4-5, 5-14, 5-62 F Feeding paper   form feed ................................ QR-2, 3-3, 3-22   line feed .................................. QR-2, 3-3, 3-22 Font ........................................................  4-5,  5-14 Function .......................................................... 5-4 H HEX-DUMP ...................................5-4,  5-54,  7-10 I IBM Proprinter XL24E ................. 2-22, 5-14, 5-62 Interface ........................................ 2-20, 5-29, D-1 L Label .............................................................  3-23 LAN interface .............................. 2-22, 5-29, D-12 LF/FF .................................................... QR-2,  3-3 Line feed ...............................QR-2, 3-3, 3-22, B-5 Line spacing  ................................. 5-18, 5-36, B-4 LIST .........................................................  5-4,  5-8 LOAD ................................................... QR-2, 3-3 Loading ..........................................3-9,  3-12,  3-16 Lubrication ...................................................... 6-1
INDEX  IN-2  User's Manual M Maintenan ce..................................................... 6-1 Margin ........................................................... 5-32 Menu ..................................... QR-2, 2-25, 4-4, 5-4 Multipart paper ............................................... B-8 N Number of copies ..................................... 3-9, B-3 O ONLINE ....................................... QR-2, 3-3, 5-41 Order number .................................................. A-1 P Page ......................................................  2-17,  2-26 PAPER OUT............................. 4-6, 5-27, 7-7, 7-9 Paper path .......................................QR-2, 3-3, 3-5 Power ................................... QR-2, 2-15, 7-7, B-1 Print area ........................................................ B-6 Print head ......................................................... 6-6 Printer  Driver ................................................. 2-27 Q QUALITY .............................................. 5-15, 7-1 Quick Reference........................................... QR-1 R Removing printed pages ................................... 4-8 Replacing ribbon cartridge ............................... 6-3 Resume printing .................................... QR-2, 4-6 Ribbon cartridge................................ 2-8, 6-1, A-1 Ribbon  subcassette .......................................... A-1 RS-232C ........................................................ 5-29        S Self-test ..........................................  2-17,  5-4,  5-52 Serial interface .............................. 2-20, 2-27, D-7 Setup mode ..................................................... 5-1 Single sheet  loading ....................................................... 3-9  Single sheets .............................................. B-6  ejecting ..................................................... 3-14 Soft ware ..........................................................  4-3 Specifications .................................................. B-1 Supplies .......................................................... A-1 T TEAR OFF................................... QR-2, 3-3, 3-20 Testing printer  offline ....................................................... 2-16  online........................................................ 2-26 Top margin..................................................... 5-19 U Unidirectional printing............................ 5-28, B-2 Un packin g .......................................................  2-2 USB interface .............................. 2-21, 5-29, D-11 V V-ALMNT function ....................................... 5-56 Vertical character displacement ...................... 5-56 W WIDTH .......................................... 5-24, B-1, B-2
  Please send your comments on this manual or on Fujitsu products to the following addresses:     North American Contact: FUJITSU CANADA INC. 6975 Creditview Road, Unit 1 Mississauga, ON, Canada L5N 8E9 Phone: +1-905-286-9666 Fax: +1-905-286-5997   European, Middle East, African Contact: Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Strasse 8 80807 Munich, Germany Phone: +49-89-62060-0 Internet: www.fujitsu.com/fts/   Australian Contact: FUJITSU AUSTRALIA LTD. Fujitsu House 2 Julius Avenue North Ryde N.S.W. 2113 Australia Phone: +61-2-9776-4555 Fax: +61-2-9776-4556   Asian Contact: FUJITSU HONG KONG LTD. 10/F., Lincoln House, 979 King's Road Taikoo Place, Island East, Hong Kong Phone: +852-2827-5780 Fax: +852-2827-4724  FUJITSU TAIWAN LTD. 19F, No.39, Section 1, Chung hwa Road Taipei, Taiwan Phone: +886-2-2311-2255 Fax: +886-2-2311-2277  FUJITSU SYSTEMS BUSINESS (THAILAND) LTD.  22-23 Fl., Exchange Tower, 388 Sukhumvit Rd. Klongtoey, Bangkok, Thailand 10110 Phone: +66-2-302-1500 Fax: +66-2-302-1555  FUJITSU ASIA PTE. LTD. 20, Science Park Road, #03-37 TeleTech Park Singapore Science Park II, Singapore 117674 Phone: +65-6512-7555 Fax : +65 6512-7502  FUJITSU PHILIPPINES, INC. 2nd Floor, United Life Building, A. Arnaiz Avenue Legaspi Village 1229, Makati City Metro Manila, Philippines Phone: +63-2-812-4001 Fax: +63-2-817-7576  FUJITSU (MALAYSIA) SDN. BHD. Level 1 & 2, No.3505 Jalan Technokrat 5 Cyberjaya, Selangor Darul Ehsan, Malaysia 63000 Tel: +60-3-8318-3700 Fax: +60-3-8318-8700  PT FUJITSU INDONESIA OFFICES Wisma Kyoei Prince 10th Floor Jl. Jend. Sudirman Kav 3-4, Jakarta Indonesia 10220 Phone: +62-21-570-9330 Fax: +62-21-573-5150  FUJITSU VIETNAM LIMITED Unit 01-03, 17th Floor, Keangnam Hanoi Landmark Tower,  Lot E6, Cau Giay New Urban Area, Me Tri Ward, Tu Liem District, Hanoi, Vietnam Phonel:+84-4-22203113  Fax: +84-4-22203114  Manufacturer contact: FUJITSU ISOTEC LIMITED Printer Business Division 135, Higashinozaki, Hobara-machi, Date-shi, Fukushima 960-0695, JAPAN Phone: +81-24-574-2236,  Fax: +81-24-574-2382 URL http://jp.fujitsu.com/group/fit/en/ Contact Email fit-gsm@cs.jp.fujitsu.com     FUJITSU OFFICES
                                                 KA02086-Y890-01EN

Navigation menu