Fujitsu Isotec 021M33342A Dot Matrix Printer User Manual Part 1 of 2

Download:
Mirror Download [FCC.gov]
Document ID	3801400
Application ID	yq0iHbUYks2mXFbC86DhKg==
Document Description	Users Manual_Part 1 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	213.63kB (2670373 bits)
Date Submitted	2018-03-29 00:00:00
Date Available	2018-03-29 00:00:00
Creation Date	2018-03-30 09:52:34
Producing Software	PDF Editor 2.2 - Foxit Software
Document Lastmod	2018-03-30 09:52:34
Document Title	Users Manual_Part 1 of 2
Document Author:	Zanvia

FUJTSU DL3100
DOT MATRIX PRINTER
USER'S MANUAL
IMPORTANT NOTE TO USERS
READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO
USERS, BYSTANDERS OR PROPERTY.
While FUJITSU ISOTEC has sought to ensure the accuracy of all information in this manual,
FUJITSU ISOTEC assumes no liability to any party for any damage caused by any error or
omission contained in this manual, its updates or supplements, whether such errors or omissions
result from negligence, accident, or any other cause. In addition, FUJITSU ISOTEC assumes no
liability with respect to the application or use of any product or system in accordance with
descriptions or instructions contained herein; including any liability for incidental or
consequential damages arising therefrom. FUJITSU ISOTEC DISCLAIMS ALL WARRANTIES
REGARDING THE INFORMATION CONTAINED HEREIN, WHETHER EXPRESSED,
IMPLIED, OR STATUTOR.
FUJITSU ISOTEC reserves the right to make changes to any products described herein without
further notice and without obligation.
Using This Product in High-risk Situation
This Product is designed, developed and manufactured as contemplated for general use, including
without limitation, general office use, personal use, household use, and ordinary industrial use,
but is not designed, developed and manufactured as contemplated for use accompanying fatal
risks or dangers that, unless extremely high safety is secured, could lead directly to death,
personal injury, sever physical damage or other loss(hereinafter “High Safety Required Use”),
including without limitation, nuclear control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile launch control in weapon
system. You shall not use this Product without securing the sufficient safety required for the High
Safety Required Use. If you wish to use this Product for High Safety Required Use, please
consult with our sales representatives in charge before such use.
EXPORT CONTRO
This manual contains technology which is subject to the Foreign Exchange and Foreign Trade Law of
Japan. This manual should not be exported or transferred to foreign countries in any fromor method, or
released to anyone other than the residents of Japan prior obtaining applicablelicense from your local
government or authorities and/ or the Ministry of Economy, Trade and
Industry of Japan in accordance with the above law.
FUJITSU DL3100
Following notes for United States are valid for
100-120V model only.
Federal Communications Commission
Radio Frequency Interference Statement
for United States Users
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15B of the FCC
Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measure:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
FCC warning: Changes or modifications not expressly
approved by the party responsible for compliance could void
the user’s authority to
operate the equipment.
NOTES
1. Testing of this equipment was performed on model number
M33342A.
2. The use of an unshielded a non-shielded interface cable with the
referenced device is prohibited. The length of the parallel interface
cable must be 3 meters (9.8 feet) or less. The length of the optional
serial interface cable must be 15 meters (50 feet) or less.
3. The length of the power cord must be 3 meters (9.8 feet) or less.
Use’s Manual
FUJITSU DL3100
The contents of this manual may be revised without prior notice and
without obligation to incorporate changes and improvements into units
already shipped.
Every effort has been made to ensure that the information included here
is complete and accurate at the time of publication; however, Fujitsu
Isotec Limited cannot be held responsible for errors and omissions.
Printer model specifications differ with the power supply input voltage
(100-120 V) and (200-240 V) .
KA02087-Y890-01EN FEBRUARY 2017
Copyright © 2017 FUJITSU ISOTEC LIMITED
Printed in Japan. All rights reserved. No part of this manual may be
reproduced or translated, stored in a database or retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written
permission of Fujitsu Isotec Limited.
TRADEMARK
ACKNOWLEDGEME
FUJITSU is a registered trademark and Fujitsu Creative Faces is a
trademark of Fujitsu Limited. Centronics is a trademark of Centronics
Data Computer Corporation. IBM PC and IBM Proprinter XL24E are
trademarks of International Business Machines Corporation. ESC/P2 is
trademark of Seiko Epson Corporation. Microsoft is a registered
trademark and MS-DOS and Windows are trademarks of Microsoft
Corporation. Nimbus Sans is a registered trademark of URW
Unternehmensberatung Karow Rubow Weber GmbH, Hamburg
Other product names mentioned in this manual may also be trademarks
of their respective companies.
ii
Use’s Manual
FUJITSU DL3100
ABOUT THIS MANUAL
Thank you for buying the Fujitsu DL3100Pro dot matrix
printer.
You can expect years of reliable service with very little
maintenance. This manual explains how to use your printer to
full advantage. It is written for both new and experienced
printer users.
PRINTER MODELS
AND OPTION
This manual describes how to install, set up, and use your
printer and printer options. It also explains how to keep the
printer in good working condition and what to do should
something go wrong. Detailed procedures are provided for
first-time users. Experienced users can skip some of the
details, using the table of contents and chapter introductions
to locate information.
This manual has several appendixes, a glossary, and an index.
Appendix
A lists supplies and additional documentation and information
available from your dealer or authorized Fujitsu representative. Fujitsu
offices are listed at the end of the manual.
This manual covers model DL3100, a 80-column printer. Each
model has a 100~120 & 200-240 power supply.
Models with the Centronics parallel +USB interfaces. You
must specify these when purchasing the printer.
DL3100
Basic specifications
Print line at 10 cpi: 80 columns (DL3100)
Control Panel: LED type
Interface: Factory default USB
Parallel, Ethernet, RS232CSerial
Alternative specification
Power supply:100~120 & 200-240
cpi: characters per inch
Use’s Manual
iii
FUJITSU DL3100
ORGANIZATION
This manual is organized as follows:
Quick Reference summarizes everyday printer operations. After you
become familiar with the printer, use this section as a memory aid.
Chapter 1, Introduction, introduces the printer and identifies key
features and options that enhance the printer’s capabilities.
Chapter 2, Setting Up, gives step-by-step procedures for setting up
the printer for immediate use and identifies the main parts of the
printer. If this is your first printer, you should read the entire chapter
before attempting to use the printer.
Chapter 3, Paper Handling, explains how to load and use paper with
your printer.
Chapter 4, Printing, covers basic printing operations. This chapter
describes everyday operations from the printer’s control panel, such as
loading paper and selecting print features, in detail. After you become
more familiar with the printer, use Quick Reference at the beginning
of the manual to refresh your memory as needed.
Chapter 5, Using Setup Mode, describes how to change the printer’s
optional settings, such as print features, hardware options, and top-ofform. Most settings only affect print features such as the typestyle and
page format. Note that certain settings directly affect hardware and
software compatibility. Refer to this chapter as indicated in Chapter 2
or as required.
Chapter 6, Maintenance, explains basic maintenance procedures for
this printer.
Chapter 7, Trouble-Shooting, describes problem-solving techniques.
Before you contact your dealer for help, check the list of problems and
solutions provided in this chapter.
Chapter 8, Installing Options, describes the options available for the
printer and explains how to install them.
At the end of this manual, you will find several appendixes, a glossary,
and an index. Appendix A gives order numbers for printer supplies,
options, and publications. Other appendixes provide additional technical
information about the printer.
iv
Use’s Manual
FUJITSU DL3100
CONVENTIONS
Special information, such as warnings, cautions, and notes, are
indicated
as follows:
WARNING
A WARNING indicates that personal injury may result if you
do not follow a procedure correctly.
CAUTION
A CAUTION indicates that damage to the printer may result if
you do notfollow a procedure correctly.
NOTE
A NOTE provides “how-to” tips or suggestions to help you
perform a procedure correctly. NOTEs are particularly useful for
first-time users.
For Experienced Users
If you are familiar with this printer or with dot matrix printers
in general this information will help you use the manual
effectively.
Use’s Manual
FUJITSU DL3100
Warning symbols
Various graphic symbols are used in this manual. They serve as signs to help users of this product use the product safely
and correctly as well as prevent damage and personal injury to the users or bystanders.The following tables show and
explain each symbol. Be sure that you understand the meaning of each
symbol before reading the manual.
WARNING
CAUTION
A WARNING indicates that death or serious
personal injury may result if you do not follow a
A CAUTION indicates that personal injury or
property damage may result if you do not follow a
procedure correctly
procedure correctly
Examples and explanations of graphic symbols
 Indicates a warning or caution item. By itself, the image in this
symbol suggests the meaning of the warning or caution (the example
on the left is a caution of possible electric shock).
 Indicates a prohibited action. The image in or beside this symbol
expresses the prohibited action (the example on the left indicates that
disassembly is prohibited).
 Indicates a direction that must be observed. The image in this
symbol shows the direction (the example on the left shows the
direction in which a power plug is disconnected from an outlet).
This symbol and accompanying statement indicate a risk of injury from
a hot object.
Caution: Hot
This symbol and accompanying statement indicate a risk of fire.
Caution: Flammable
This symbol and accompanying statement indicate a risk of injury from
touching part of the equipment.
Do not touch
This symbol and accompanying statement indicate a risk of injury,
such as from electric shock, caused by disassembling the equipment.
Do not disassemble
This symbol and accompanying statement indicate a general prohibited
action.
General prohibited
action
This symbol and accompanying statement indicate a general caution.
General caution
vi
Use’s Manual
FUJITSU DL3100
Notes on Safet
WARNING
WARNING
Do not place a container containing water, such as a vase, potted plant, and drinking glass,
or a metal object on or near the printer.
Otherwise, electric shock or fire may result.
Do not place the printer in a humid or dusty area, in an area with explosive fumes, an area
with poor ventilation or close to a fire.
Otherwise, electric shock or fire may result.
Use only one of the power cords included with this product, for this product. Do not use
any other power cord for this product.
Otherwise, electric shock or fire may result.
Do not use this product in an area exposed to a high level of moisture, such as a bathroom
and shower room.
Otherwise, electric shock or fire may result.
Use’s Manual
vii
FUJITSU DL3100
WARNING
When mounting or removing an optional device or component, turn off the power to the
printer and personal computer and disconnect their power plugs from the outlets before
performing the work.
Otherwise, electric shock may result.
Connect only Fujitsu-recommended optional devices and components.
Otherwise, electric shock or fire may result.
CAUTION
Do not block openings in the printer (e.g., ventilation openings)
If ventilation openings are blocked, heat accumulates inside the printer, possibly resulting
in a fire.
Do not place a heavy object on the printer. Also, do not subject the printer to shocks.
Otherwise, the printer may become unbalanced, causing it to fall, and possibly resulting in
personal injury.
Do not place the printer in an area exposed to strong vibration or an unstable area such as
on a slope.
Otherwise, the printer may fall or topple, possibly resulting in personal injury.
Do not leave the printer in an area exposed to direct sunlight for a long time, such as inside
a car under the sun or any other area subjected to high temperatures.
Otherwise, the printer surface heats up, possibly melting covers or resulting in other
deformities, or the inside of the printer may become extremely hot, possibly resulting in
fire.
Before moving the printer, be sure to disconnect the power plug from the outlet and
disconnect all connected cables from the printer.
Otherwise, the power cord may be damaged, possibly resulting in electric shock or fire, or
the printer may fall or topple, possibly resulting in personal injury.
Before connecting or disconnecting a printer cable, be sure to turn off the power to the
printer and personal computer.
Performing that and related work without the power turned off may result in a personal
computer or printer failure.
viii
Use’s Manual
FUJITSU DL3100
Notes about the printer in operation
WARNING
If the printer is making a strange noise, which indicates a problem, discontinue printer
operation. Request your printer dealer to fix the problem.
Continued operation of the printer without repairs may result in electric shock or fire.
Do not use a power source whose voltage is other than that indicated. Also, an excessive
number of plugged-in power cords must not be connected to a single outlet.
Otherwise, electric shock or fire may result.
Do not spill any liquid, such as water, on the printer.
Otherwise, electric shock or fire may result.
Do not damage or modify the power cord.
The power cord may be damaged by placing a heavy object on it, stretching it excessively,
forcibly bending it, twisting it, or heating it, and this may result in electric shock or fire.
Do not use the power cord if it or the power plug is damaged or the plug does not fit
securely in the outlet receptacle.
Using the power cord in that condition may result in electric shock or fire.
Do not insert the power cord into an outlet or turn on the power to the printer when any of
its covers has been removed.
Otherwise, electric shock or fire may result.
Prevent foreign objects, such as metal shards and inflammable materials, from being
inserted or dropped into any openings in the printer (e.g., ventilation openings).
Otherwise, electric shock or fire may result.
Do not disconnect the power plug from the outlet while the power to the printer is turned
on.
Otherwise, the plug becomes deformed, possibly resulting in fire
Do not remove the main printer cover or the cover for the cable connectors except as
necessary. To check and repair internal components, request your printer dealer to do so.
Some internal components use high voltage, and touching them may result in electric
shock.
Do not modify the printer by yourself.
Otherwise, electric shock or fire may result.
Do not connect or disconnect the power plug with wet hands.
Otherwise, electric shock may result.
Use’s Manual
ix
FUJITSU DL3100
WARNING
If excessive heat, smoke, a strange odor, or a strange noise is coming the printer or any
other abnormality is observed, immediately turn off the power to the printer by using the
power switch, and be sure to disconnect the power plug from the outlet.
Then, after verifying the end of the abnormality (e.g., no more smoke is coming from the
printer), request your printer dealer to make repairs. Do not repair the printer by yourself
as doing so is dangerous.
Continued use of the printer when it is operating abnormally may result in electric shock or
fire.
If a foreign object (e.g., water or other liquid, metal shard) has entered the printer,
immediately turn off the power to the printer by using the power switch, and disconnect the
power plug from the outlet. Then, contact your printer dealer.
Continued use of the printer in that condition may result in electric shock or fire.
Customers who use the printer near children should take especial care regarding this point.
If the printer is dropped or a cover is damaged, turn off the power to the printer by using
the power switch, and disconnect the power plug from the outlet. Then, contact your
printer dealer.
Continued use of printer in that condition may result in electric shock or fire.
Before performing cleaning, maintenance, or troubleshooting work on the printer, switch
off the power switch, and be sure to disconnect the power plug from the outlet.
Performing that work on the printer without the power turned off may result in burns or
electric shock
If dust accumulates on or near the metal parts of the power plug, so wipe away that dust
with a dry cloth.
Continued use of printer in that condition may result in fire.
Do not drop or strike the printer, such as by hitting it against something.
Otherwise, a failure may result
Use’s Manual
FUJITSU DL3100
CAUTION
Insert the power plug completely into an outlet so that it is securely connected.
Otherwise, electric shock or fire may result.
Exercise caution to keep loose clothing, hair, neckties, etc. away from paper feed- or
ejection openings, and tractors while the printer is operating.
Otherwise, personal injury may result.
When disconnecting the power plug from the outlet, pull it out while grasping the plug, not
the cord.
If you pull it out while grasping the cord, the insulation may be damaged or the cable core
may be exposed or damaged, possibly resulting in electric shock or fire.
Do not cover or wrap the printer with a cloth or anything else while it is operating.
Otherwise, heat accumulates, possibly resulting in fire.
Do not use the power cord with it bunched together.
Otherwise, heat accumulates, possibly resulting in fire.
If the printer operates when the front cover is unclosed, immediately turn the printer off,
and unplug the power code from wall outlet.
Then contact your printer dealer to make repair of safety interlock.
Continued use of the printer in that condition, operation of the mechanism inside of the
front cover may become a cause of an injury.
If the printer is not to be used for a long time, disconnect the power plug from the outlet
for safety reasons.
Otherwise, electric shock or fire may result.
If a lightning storm is in nearby, disconnect the power plug from the outlet.
Leaving the plug connected to the outlet may result in damage to the printer or other
property damage
Use’s Manual
xi
FUJITSU DL3100
CAUTION
The print head and internal frames become extremely hot during printer operation and
remain so immediately afterwards. Do not touch these parts until sufficient time has
passed to allow them to cool.
Otherwise, burns or personal injury may result.
Do not touch the paper feed- or ejection openings while the printer is operating.
Otherwise, personal injury may be result.
Do not touch the printer cable connectors or the metal part of the print head.
Otherwise, personal injury or a printer failure may result.
Do not touch the print head while it is moving.
Otherwise, burns or personal injury may result.
Note that continuous forms that are fed in the reverse direction continuously may come off
the paper feed tractors.
Operate the printer with the paper thickness set to the appropriate paper thickness.
Use only an original ribbon cassette that is specified as suitable by Fujitsu.
Textile fibers accumulate on components inside the printer and parts of the roller, so clean
these parts regularly.
Do not turn the ribbon feed knob in the reverse direction.
Otherwise, the ribbon may become jammed and stuck.
If printing is started with a slack ribbon, the ribbon may become tangled or the ribbon feed
mechanism may become locked.
The print head is extremely hot immediately after printing. When replacing the ribbon,
verify that the print head is sufficiently cool before setting the print head to the ribbon
replacement position.
xii
Use’s Manual
FUJITSU DL3100
TABLE OF CONTENTS
.. Unpacking Guide ................................................................... ........... .............. 1-1
SELECTING A GOOD LOCATION ..................................................................................... 1-2
UNPACKING THEPRINTER .............................................................................................. 1-3
PRINTER COMPONENTS ................................................................................................ 1-5
.Setting Up Printer ................................................................... ........... ..................2-1
Install Ribbon................................................................................................................. 2-2
Install the single sheet feeder ....................................................................................... 2-4
Connecting the Interface Cable ..................................................................................... 2-6
Connecting the Power Supply ....................................................................................... 2-7
Installing the Windows Driver ....................................................................................... 2-8
Paper Installation Guide .......................................................... ........... ..................3-1
Adjusting the Print Gap Lever ....................................................................................... 3-2
Friction Feed Handling .................................................................................................. 3-3
Tractor Feed Handling ................................................................................................... 3-4
Continuous Paper Placement ........................................................................................ 3-5
TIPS ON PAPER HANDLING ............................................................................................ 3-6
Control Panel Operation.......................................................... ........... ..................4-1
LED Indicators................................................................................................................ 4-3
Control Panel Keys......................................................................................................... 4-4
Panel Operation ............................................................................................................ 4-7
Online State ................................................................................................................... 4-8
Setup State .................................................................................................................... 4-9
Power-on State .............................................................................................................. 4-11
Printer Setting Changes ........................................................... ........... ..................5-1
System Setup ................................................................................................................. 5-2
Paper Setup ................................................................................................................... 错误!未定
义书签。
Interface Setup .............................................................................................................. 错误!未定
义书签。
Character Setup............................................................................................................. 错误!未定
义书签。
Other Setup ................................................................................................................... 错误!未定
义书签。
German (Deutsch) ............................................................................................... 5-11
Russian (Россия)................................................................................................... 5-14
Italian (Italiano)..................................................................................................... 5-17
French (Français) .................................................................................................. 5-19
Spanish (Español) ................................................................................................. 5-22
Turkish (Türkce) ................................................................................................... 5-25
Portuguese (Português) ......................................................................................... 5-28
Black Mark Paramenters ............................................................................................... 5-31
Use’s Manual
xiii
FUJITSU DL3100
Bidirectional Alignment................................................................................................. 5-35
. Customized Form ................................................................... ........... ..................6-1
Customize Cut Sheet Form Length ................................................................................ 6-2
Customize Cut Sheet TOF .............................................................................................. 6-5
Customize Cut Sheet Bottom Margin ............................................................................ 6-6
Customize Cut Sheet Left Margin .................................................................................. 6-6
Customize Fanfold Page Formatting Parameters .......................................................... 6-7
..... MAINTENANCE ................................................................... ........... ..................7-1
CLEANING ...................................................................................................................... 7-2
Cleaning the Platen ( Paper Rollers ) ............................................................................. 7-4
REPLACE THE RIBBON ................................................................................................... 7-5
TROUBLE-SHOOTING ............................................................... ........... ..................8-1
SOLVING PROBLEMS...................................................................................................... 8-2
Print Quality Problems ......................................................................................... 8-2
Paper Handling Problems and Solutions .............................................................. 8-4
Operating Problems and Solutions....................................................................... 8-6
Printer Failures ..................................................................................................... 8-7
Diagnostic Functions ..................................................................................................... 8-8
Getting help................................................................................................................... 8-8
SUPPLIES AND OPTIONS .......................................................... ........... ..................9-1
SUPPLIES........................................................................................................................ 9-1
OPTIONS ........................................................................................................................ 9-1
PRINTER AND PAPER SPECIFICATIONS................................... ........... ............... 10-1
PHYSICAL SPECIFICATIONS ............................................................................................ 10-1
FUNCTIONAL SPECIFICATIONS....................................................................................... 10-2
PERFORMANCE SPECIFICATIONS ................................................................................... 10-5
PAPER SPECIFICATIONS.................................................................................................. 10-8
COMMAND SETS ................................................................... ........... ............... 11-1
ESC/P2 Emulation Command List .................................................................................. 11-2
IBM Emulation Command List ....................................................................................... 11-23
DPL24C Plus Additional Commands .............................................................................. 11-38
INTERFACE INFORMATION .................................................... ........... ............... 12-1
Parallel interface ........................................................................................................... 12-2
USB interface ................................................................................................................. 12-6
Serial interface .............................................................................................................. 12-7
Ethernet interface ......................................................................................................... 12-11
Character sets & Code Pages................................................. ........... ............... 13-1
Character Sets ............................................................................................................... 13-1
Code Page Commands .................................................................................................. 13-6
Code Page Tables........................................................................................................... 13-8
RESIDENT FONTS................................................................... ........... ............... 14-1
xiv
Use’s Manual
FUJITSU DL3100
Unpacking Guide
If this is your first printer, you should read the entire chapter before
attempting to use the printer.
In this chapter, you will learn how to:
·Select a good location for the printer
·Unpacking the Printer
·Know the name of the printer components
Use’s Manual
1-1
FUJITSU DL3100
This printer is suitable for most business, office, and home
SELECTING A
environments.
GOOD LOCATION To obtain peak performance from the printer, select a
location that meets
the following guidelines:
√ Place the printer on a sturdy, level surface.
√ Place the printer near a well-grounded AC power
outlet.
√ Ensure easy access to the front and rear of the printer
by leaving several inches of space around the printer.
Do not block the airvents on the front, left, and right
sides of the printer.
√ Do not place the printer in direct sunlight or near
heaters.
√ Make sure that the room is well-ventilated and free
from excessive dust.
√ Do not expose the printer to extremes of temperature
and humidity.
√ Use only the power cord supplied with the printer or
recommended by your dealer. Do not use an extension
cord.
√ Do not plug the printer into a power outlet that is
hared with heavy industrial equipment, such as
motors, or appliances, or such as copiers or coffee
makers. Such equipment often emits electrical noise or
causes power degradation.
1-2
Use’s Manual
FUJITSU DL3100
UNPACKING
THEPRINTER
Unpack the printer as follows:
1. Place your packaged printer on a solid base.
2. Make sure that the “Up” symbols point in the correct
direction.
3. Open the packaging, lift the printer out of the cardboard
box and remove the remaining packaging material.
4. Check the printer for any visible transport damage and
missing items. If you find any transport damage or if any
accessories are missing, please contact your dealer. The
following items are included:
oPrinter
oPaper feed knob
oSheet feeder
oPower cord
oRibbon cartridge
oCD-ROM
oInstallation Guide
oUSB cable
Use’s Manual
1-3
FUJITSU DL3100
Remove the packaging materials from the printer as follows:
1. Open and remove the top covers of the printer
following the below picture.
2. Remove the shipping cardboard from around the print
head.
3. Install the paper feed knob. Rotate the paper feed
knob to make it fix with the latch. And then press it to
lock.
1-4
Use’s Manual
FUJITSU DL3100
PRINTER
COMPONENTS
See the table of next page.
Use’s Manual
1-5
FUJITSU DL3100
Component
Gap Lever
Adjusts the print gap lever
according to the thickness of paper
Paper Guides
Adjusts positioning of single sheet
paper
Print Head
24-pin printing mechanism
Cover
Control Panel
Paper Feed Lever
Paper Feed Knob
Protects print head and other
components inside, and reduce
noise
Shows printer status, for printer
setup
Two positions:
= continuous forms;
= single sheet paper
Manual feed or vertical positioning
of paper
Power Switch
Power printer ON or OFF
Ribbon Cartridge
Install ribbon in the printer
For guiding ribbon installation on
print head
For feeding and adjustment of
continuous forms
Connects power cord to the printer
Connects interface cables from the
Ribbon Guide
Tractors
Power Socket
Interface
1-6
Function
Use’s Manual
FUJITSU DL3100
Setting Up Printer
Your new printer is easy to install and set up.
This chapter tells you how to set up the printer and start printing
right away.
In this chapter, you will learn how to:
·Install Ribbon
·Install the single sheet feeder into the rear of the printer
·Connecting the Interface Cable
·Connecting the Power Supply
·Installing the Windows Driver
Use’s Manual
2-1
FUJITSU DL3100
Install Ribbon
Installing the Ribbon cartridge
（HOT）
CAUTION 
The print head and metal frame is hot during
printing or immediately after printing. Do not touch
them until it cools down.
1. Ensure the power to the printer is off and the print gap lever
“A” is set to the furthest open position. Move the carriage
to the center of the print platen.
2. Install the recess positions ①-② on the ribbon cassette into
the printer mounting.
3. Press the ribbon frame ③ onto the print head.
4. Turn the ribbon knob ④ in clockwise direction until the
ribbon fabric is taut. Move the carriage left and right to
ensure the carriage and ribbon fabric can move smoothly.
5. Ensure the print gap lever “A” is set to the original
position.
6. Close the printer’s cover. When printer is in operation,
ensure the printer’s cover is closed to keep the noise level to
a minimum.
2-2
Use’s Manual
FUJITSU DL3100
Notes on Ribbon Cartridge Removal:
1. Eject any paper loaded in the printer.
2. Turn off the printer power.
3. Open and remove the cover.
4. Set the gap lever to the most open position labeled
“RIBBON”.
5. Move the carriage to the middle. Be careful not to touch the
print head if printing had just been performed, as the print
head may be hot.
6. Remove the ribbon frame from the print head.
7. Use fingers to take hold of the handle on the ribbon cartridge
firmly, and lift the cartridge upwards to unlatch it. Some
force may be needed to unlatch the cartridge.
Use’s Manual
2-3
FUJITSU DL3100
Install the single
sheet feeder
Install the single sheet feeder into the rear of the printer. If
you intend to use this paper way, assure having removed the
fanfold paper out of the rear tractor paper way by pressing
【Load/Eject】Key.
Then switch the paper feed lever to Single.
1. As shown in the picture below, unfold the Paper Guides
first. Then put the Single Sheet Feeder into its installation
position and push it down to latch.
2-4
Use’s Manual
FUJITSU DL3100
2. Push the Single Sheet Feeder backward to make it latch
again.
Use’s Manual
2-5
FUJITSU DL3100
Connecting the
Interface Cable
The USB port is located at the rear of the printer.
IMPORTANT: Make sure the printer and the computer are
switched off before connecting or disconnecting the interface
cable to prevent electrical damage to the interface ports.
The printer may also be purchased with an
additional interface. The additional interface
can be one of the followings: Parallel, Serial,
Ethernet.
2-6
Use’s Manual
FUJITSU DL3100
Connecting the
Power Supply
Checking the printer voltage
Make sure that the device has been set according to your
country’s power supply voltage. To do this, check the rating
plate at the back of the printer. Contact your dealer if the
setting is incorrect.
Never switch on the printer if the voltage setting is
incorrect; This may result in electrical damage to
the printer.
Make sure that the power switch “A”, located to the left side
of the printer, is in the “O” (off) position.
Connect the power cord to the power inlet of the printer.
Connect the power cord plug to a mains socket. Switch on the
printer.
Use’s Manual
2-7
FUJITSU DL3100
Installing the
Windows Driver
A printer driver is required for using the printer in a Windows
environment. Special printer drivers are provided with the
DL3100 printer.
For information about how to install printer drivers, refer
to ’Printer Driver Installation Giude’ or Readme.txt of the
printer driver to be installed.
- These printer drivers run with DLP24C+ emulation.
Be sure to specify DLP24C+ emulation for the
printer mode.
- The DL3100 printer driver is a printer driver for
monochrome printing.
The color data printing result may differ from its
print preview or the
monochrome data printing result.
Printer Driver Installation Giude can be opened from
'FUJITSU DL Series Software Setup'.
2-8
Use’s Manual
FUJITSU DL3100
Paper Installation Guide
The printer can handle either single sheets or continuous forms.
Single sheets, also called cut sheets, include envelopes and noncontinuous, multipart forms. Continuous forms include labels and
multipart forms fed into the printer using the forms tractors. The
printer is able to print 1~5 plies multipart paper.
This chapter explains how your printer uses paper.
Topics covered are:
·Adjusting the Print Gap Lever
·Friction Feed Handling
·Tractor Feed Handling
·Continuous Paper Placement
·Tips on paper handling
Use’s Manual
3-1
FUJITSU DL3100
Adjusting the
Print Gap Lever
Remove any paper clip or staple. Do not load paper that
has been folded or damaged, wrinkled, or curled.
The print gap lever is on the left side of the printer inside
the top cover. Take care to adjust the print gap lever to a
suitable position whenever you change the number of
copies being printed. Using the wrong print gap may cause
print head damage or paper jams.
3-2
Paper type
Weight
(g/m2) / ply
Thickness
(mm)
Gap lever
position
Single sheet
52~100
0.06~0.12
1P~2P
3-ply
4-ply
5-ply
6-ply
7-ply
Change
40~52
40~52
40~52
40~52
40~52
---
0.12~0.14
0.17~0.22
0.23~0.27
0.28~0.34
0.35~0.41
Above 0.58
3P~4P
4P~5P
5P~6P
6P~7P
7P
RIBBON
Use’s Manual
FUJITSU DL3100
Friction Feed
Handling
There are 2 paper feed modes: friction feed and tractor
feed.
1. Raise the single sheet feeder until it locks into its
mounting.
2. Move the paper-feed lever forward to “ ” for friction
feed mode. Make sure that no paper is in the printer when
you switch the paper path.
3. Adjust the print gap lever if necessary.
4. Align the left paper guide with the mark on the left of the
single sheet feeder.
5. Adjust the right paper guide to the width of the paper used.
6. Insert a sheet of paper. Make sure that the bottom edge of
the paper engages snugly with the platen. Please push the
paper in manually if the paper does not feed in while the
friction roller is running.
7. The paper should advance automatically to the print
position. The printer is now ready to print in the online
state.
Use’s Manual
3-3
FUJITSU DL3100
Tractor Feed
Handling
1. Move the paper-feed lever backward to “
” for
continuous paper position.
2. Adjust the print gap lever if necessary.
3. Raise the tractor doors and fit the first 3 paper holes onto
the left tractor pins. Close the left tractor door. In the same
way, install the paper on the right tractor.
4. Adjust the right tractor to the width of the paper until the
paper is flat. Do not stretch the paper too taut. Push the
right lock lever down to secure the right tractor in place.
5. Press the【Load/Eject】key to load the paper to the
starting print position. The printer is now ready to print in
the online state.
3-4
Use’s Manual
FUJITSU DL3100
Continuous Paper
1. Place the printer on a solid base. The minimum suitable
Placement
height of the solid base is 75 cm.
2. Left and right positioning: The direction of continuous
paper should be parallel with the paper guide. The
tolerance should be less than 3 cm.
Attention：If you want to use continuous paper, make sure
that the Cut Sheet Guide is not standing.If the Cut Sheet
Guide is in state, it may hinder the continuous paper feed
and cause a paper jam.
3. Front and back positioning: The distance between the rear
of printer and the wall should be more than 60cm. To
avoid paper jam, the distance between the continuous
paper and the edge of desk should be 10~15 cm.
Use’s Manual
3-5
FUJITSU DL3100
TIPS ON PAPER
HANDLING
General Tips
 Use high-quality paper. Do not use paper that is wrinkled or curled at
the edges.
 Do not use paper with staples or metal parts.
 Do not use paper with unpredictable variations in thickness, such as
paper with partial multilayers, paper with embossed printing, and
labels with the backing sheet exposed.
 Store paper in a clean, dry environment.
3-6
Use’s Manual
FUJITSU DL3100
Control Panel Operation
This chapter describes the following everyday printing operations:
·LED Indicators
·Control Panel Keys
·Panel Operation
·Online State
·Setup State
·Power-on State
Use’s Manual
4-1
FUJITSU DL3100
There are 4 switches S1~S4 and 4 LEDs L1~L4. The
meaning and application of each switch and LED are
described below pages.
4-2
Use’s Manual
FUJITSU DL3100
LED Indicators
LED
Function
L1
L2
L3
L4
Power/Paper Out
Font1
Font2
Online
1.“Power/Paper Out” LED：
On: Power on
Flashing: Paper out, Energy saving mode。
Flashing + buzzer: Paper jam
2. Font 1 and Font 2” LED
Flashing together: Indicates continuous paper is at
tear-off position; otherwise it indicates the selected font. See
table 4.1.
table 4.1
Font Selection Label
Tear Off
Draft
Draft Condensed
Roman
Sans Serif
Courier
Prestige
Script
Others
(see Menu setting)
L2 State
L3 State
Blink
Off
Off
Off
On
On
On
Blink
Blink
Off
On
Blink
Off
On
Blink
Off
Blink
On
3. “Online” LED:
On: The printer is in online state and ready to receive
data from the computer.
Off: The printer is in offline state and cannot receive
data.
Use’s Manual
4-3
FUJITSU DL3100
Control Panel
Keys
Switch
Label
S1
S2
S3
S4
Tear off
LF/FF
Load/Eject
Online
1.“Tear Off” Key:
This is valid for tractor mode only. It feeds the form to the tearoff position. After tearing off the form, printing starts on the
next TOF by pressing any key or receiving print data from the
host.
When online, this key will move any loaded continuous paper
to the tear-off position. When in setup state, this key is used to
select the desired font.
2.“LF/FF” Key:
Pressing this key will feed paper one line forward. By holding
down this key, the printer will initially feed a few lines, then
perform a form feed (continuous paper mode) or eject the form
(single sheet mode).
3.“Load/Eject” Key:
Load: Automatically loads the paper (according to path
selection) when no paper is on the platen.
Eject: For rear tractor, it retracts the form from the platen to
4-4
Use’s Manual
FUJITSU DL3100
allow users to install cut sheets. (NOTE: Users have to toggle
the path selection lever.) For cut sheets, it ejects the form on
the platen.
When paper is loaded, pressing this key will eject the paper
(single sheet mode) or park the paper (continuous paper
mode). When paper is not loaded, pressing this key will load
the paper to the starting print position.
4.“Online” Key:
Toggles between Online and Offline states.
This key switches the printer between online and offline
states. Printing is stopped when the printer is switched to
offline state. When printer is switched to online state again,
printing will resume.
5.“Clear Buffer and Reset” Key:
In offline state, press switch S1 while holding S4.
Clears the print buffer. beeps once upon completion
Pressing S1 longer initializes the printer to default settings.
Beeps 3 times upon completion.
6.“Clear Life Time” Key:
Use’s Manual
4-5
FUJITSU DL3100
Press the [skip line] + [feeding paper/return paper] enter the counter
initialization mode, and the font light1 and font light2 alternate.
On this mode, press the [tearing paper] button and then the buzzer
honks, the power supply life will be initialized.
Press the [skip line] button and then the buzzer honks, the device
server life will be initialized.
Press the [feeding paper/return paper] and then the buzzer honks, the
print platen server life will be initialized.
Press the [Online] button and then the buzzer honks, the ribbon server
life will be initialized.
Press the [skip line] + [feeding paper/return paper] at the same time
and then the buzzer honks, the print head server life will be initialized.
Press the [tearing paper] + [Online] at the same time and then the
buzzer honks, the server life of all the printer parts will be initialized.
Press the [tearing paper] + [skip line] + [feeding paper/return paper] +
{Online} at the same time. End counter initialization function and the
printer will restart
4-6
Use’s Manual
FUJITSU DL3100
Panel Operation
There are 3 states of operation: Online, Setup and Power
On.
In the Online state, the keys provide the following
functions: Go to Tear Off position, Line Feed/Form Feed,
Load/Eject, Clear Buffer and switch to offline state for
accessing to Setup state.
In the Setup state, the keys provide font selection, micro
feed and quiet mode printing..
To enter the Power On state, the user holds down a key or a
combination of keys while powering up the printer. This
state provides the following functions: Hex-dump, Main
Menu setup, print Main Menu, print lift-time information,
Customize Form.
The followings describe the 3 states in details.
Legend:
[A] = press and hold switch A
{B} = press and then release switch B
[A]+ {B} = press switch B while holding
Use’s Manual
4-7
FUJITSU DL3100
Online State
Function
Name
Switch
Operation
LED
Function Description
Tear Off
{S1}
L2, L3
flash
This is valid for tractor mode only. It feeds the form
to the tear-off position. After tearing off the form,
printing starts on the next TOF by pressing any key
or receiving print data from the host.
LF
{S2}
Feeds one line with every press of S2
Pressing this key will feed paper one line forward.
By holding down this key, the printer will initially
feed a few lines, then perform a form feed
(continuous paper mode) or eject the form (single
sheet mode).
Load: Automatically loads the paper (according to
path selection) when no paper is on the platen.
Eject: For rear tractor, it retracts the form from the
platen to allow users to install cut sheets. (NOTE:
Users have to toggle the path selection lever.) For cut
sheets, it ejects the form on the platen.
FF
[S2]
Load/Eject
{S3}
Online
{S4}
L4
Toggles between Online and Offline states.
Setup State
[S4]
L4
Hold the S4 key for 3 seconds. Toggles to 3s Setup
state. Indicated by flashing L4.
--
Clears the print buffer. Beeps once upon completion.
Pressing S1 longer initializes the printer to default
settings. Beeps 3 times upon completion.
Clear Buffer
[S4]+{S1}
and Reset
Clear Life
Time
4-8
[S2]+[S3]
L2, L3
The server life of all the printer parts will be
flash
initialized.
alternate
Use’s Manual
FUJITSU DL3100
Setup State
3 seconds setup state
Function
Switch
Name
Operation
LED
Function Description
Online state
{S4}
L4
Toggling to the Online state will cause the printer to go
into a ready-to-print state. Any changes made in Setup
state will be saved permanently. Lighting up L4
indicates the Online state.
Micro UP
{S3}
--
Press S3 to micro feed paper up.
Micro Down
{S2}
--
Press S2 to micro feed paper down.
Font Select
{S1}
L2, L3 Refer to Table 4.1 for details.
2 Seconds setup state
Hold the S3 key for 2 seconds,toggles to 2s Setup state. Indicated by flashing L1.In the 2
seconds setup state,Press S1(Tearoff button)can choose the silent mode, the buzzer will
call, you can set the automatic silent mode,print once,print twice, and print thrice.
Use’s Manual
4-9
FUJITSU DL3100
Function Name
Switch
LED
Operation
Automatically
determines the
number of prints
based on the
segmentation mode
{S1}
print once
（Segmentation is
invalid）
{S1}
--
print twice (Parity
{S1}
--
print thrice（8
dots/group）
{S1}
--
4-10
Function Description
-Press S1(Tearoff button)can choose the
silent mode, the buzzer will call, you can
set the automatic silent mode,print
once,print twice, and print thrice.
Use’s Manual
FUJITSU DL3100
Power-on State
Use’s Manual
4-11
FUJITSU DL3100
Function
Name
Switch
Operation
LED
Function Description
Beeps once to indicate going into hex dump mode:
Prints data from host in hexadecimal representation.
Pressing S4 suspends the printing.
Hex Dump
[S3]
When the hex dump has finished, pressing S4 forces the
printing of the last line of data, as any line termination
control code from host has no function.
Switch off the power to terminate the hex dump.
Menu Setup /
EDS
[S1]
Self Test /
Status Page
[S4]
Customize
Form
[S3] + [S4]
Life Time
[S2]
4-12
Allows for Main Menu setting changes. Please read the
instructions printed on how to change settings when this
mode is activated. (EDS: Electronic DIP Switch)
Prints the printer settings and self-test pattern.
To customize the margins and tear-off position, please
refer Chapter 6 for details.
Printing the information of consumables
Use’s Manual
FUJITSU DL3100
Printer Setting Changes
In order to meet specific print requirements, the printer
configurations may be changed as follows: Hold down the【Tear
off】key while powering on the printer and then release the key
when the print head starts to move. The printer will enter Main
Menu setup state. Follow the instructions printed on how to make
setting changes. When a new setting is saved, it is retained after the
printer has been powered off.
The Printer Settings menu contains 8 sub-menus:
System Setup, Paper Setup, Interface Setup,
Character Setup, Other Setup, Bi-directional
Alignment, BlackMark Mode, Restore Factory
Defaults.
This chapter describes the following operations:
·System Setup
·Paper Setup
·Interface Setup
·Character Setup
·Other Setup
·Black Mark Parameters
·Bidirectional Alignment
Use’s Manual
5-1
FUJITSU DL3100
System Setup
System setup
Valid Settings
Function
Language
English, Deutsch,
Poccия, Italiano,
Français, Español,
Türkçe, Português
Allows user to select one of the following
languages: English, German, Russian, Italian,
French, Spanish and Turkish, Portuguese
Emulation
ESC/P2, IBM
Selects the printer emulation. This should be
the same as the host printer driver.
Auto CR
(ESC/P2)
No, Yes
Auto CR (IBM)
No, Yes
Auto LF
No, Yes
Yes: LF = LF+CR; No: LF = LF
(Applies to ESC/P2 emulation only)
Yes: LF = LF+CR; No: LF = LF
(Applies to IBM emulation only)
Yes: CR = CR+LF; No: CR = CR
Bi-Dir: Graphics and text are printed in both
directions, resulting in faster printing speed.
Print Dir
Bi-Dir, Uni-Dir
Uni-Dir: Graphics and text are printed from
left to right, resulting in higher precision.
Disable: Grids in block graphics are disjoint,
but grids by graphics commands or slanted
grids (block graphics) are not affected.
Enabled: Vertical grids are continuous in all
line spacing.
Form Line
Disable, Enabled,
Dashed, NoPrint
Dashed: Horizontal grids are printed in
dotted lines and vertical grids are not
affected.
NoPrint: Grids are not printed. But nested
grids (by graphical commands) above 2
levels deep are printed.
0: No-slashed Zero 0.
Zero
5-2
0, Ø
Ø: Slashed Zero Ø.
Use’s Manual
FUJITSU DL3100
System setup
Valid Settings
Function
The “LQ Text Quality” parameter is invalid
when Font is set to Draft.
LQ Text Quality
LQ, NLQ
Change Pin#1:
No, 1, 2, 3, 4, 5, 6, 7,
8, 9, 10, 11, 12, 13,
14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
Change Pin #2
When Font is set to another font other Draft,
the “LQ Text Quality” parameter will
determine whether to print in NLQ mode or
LQ mode.
Defines the first broken / worn out pin. This
pin will be substituted by an adjacent pin in
the second pass printing.
No: Not to substitution of the worn out pin.
No, 1, 2, 3, 4, 5, 6, 7, Defines the first broken / worn out pin. This
pin will be substituted by an adjacent pin in
8, 9, 10, 11, 12, 13,
the second pass printing.
14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24 No: Not to substitution of the worn out pin.
Defines the idle period before the printer
gets into Save-energy Mode.
Power-Saving
OFF, 1min, 2min,
5min, 10min
Print Mode
Performance：print quality is best, but print
speed is relatively slow.
Performance,Stan Standard: print quality and print speed can
meet the requirement of general users.
dard,Speed
Speed: print speed is fastest, but print
quality is relatively decreased
MultiPaper
Disable, Standard,
Enhance
Impact
Normal, Heavy
Graphic Speed
Normal, Fast, Ultra
Use’s Manual
OFF: The printer never goes into Saveenergy Mode.
Disable: The printer ignores the
determination of paper thickness sensor; it
keeps the impact force and the print speed
unchanged.
Standard: The printer increases the impact
force and reduces the print speed.
Enhance: The printer prints with even
stronger impact force and slower print
speed.
Normal: The print speed is faster causing
head hot easily and the impact force is
weaker.
Heavy: The print speed is reduced, resulting
better thermal performance and copy
capability.
Selects different print quality and print
speed for graphic.
5-3
FUJITSU DL3100
Paper Setup
Paper Setup
Single FormLen
Single Top
Single Bottom
Valid Settings
2.5, 11/4, 3, 3.5,11/3,
4, 5, 5.5, 6, 7, 8, 9,
10, 11, 12, 14, A4,
B4, Define
-1, 0, 1, 1.8,2,3,4,5,
6,7,8,9,10,11,12,13,1
4,15,16,17,18,19,20,
21,22,23,24,25,26,27
,28,29,30,31,32,33,3
4,35,36,37,38,39,40,
41,42,43,44,45,46,47
,48,49,50,51,52,53,5
4,55,56,57,58,59,60,
61,62,63,64,65,66
0, 1/6, 1/4, 1/3, 1/2,
2/3, 3/4, 1, Define
Function
Sets the page length in inches for single
paper
Defines the separation in1/6 inches from the
top edge of a single paper to the first print
line.
Defines the separation in inches from the
bottom edge of a single paper to the last print
line.
0, 1, 2, 3, 4, 5, 6, 7, Compensation value added to Single Left
Single Left
8,9,10,11,12,13,14,1 Mrg.
Mrg (1/180inch)
5,16,17,18,19,20
0, 1, 2, 3, 4, 5, 6, 7,
Single Top
8,9,10,11,12,13,14,1 Compensation value added to Single Top.
Mrg (1/180inch) 5,16,17,18,19,20,21,
22,23,24,25,26,27,28
Defines the setting time before a single sheet
is loaded.
Disable, 0.5sec,
Single Auto Load
1sec, 1.5sec, 2sec
Disable: Press the【Load/Eject】key
manually to load a single sheet.
Fanfold
FormLen
Fanfold Top
Fanfold Bottom
5-4
2.5, 11/4, 3, 3.5,
11/3, 4, 5, 5.5, 6, 7,
8, 9, 10, 11, 12, 14,
A4, B4, Define
-1, 0, 1, 1.8, 2,3,4,5,
6,7,8,9,10,11,12,13,1
4,15,16,17,18,19,20,
21,22,23,24,25,26,27
,28,29,30,31,32,33,3
4,35,36,37,38,39,40,
41,42,43,44,45,46,47
,48,49,50,51,52,53,5
4,55,56,57,58,59,60,
61,62,63,64,65,66
0, 1/6, 1/4, 1/3, 1/2,
2/3, 3/4, 1, Define
Sets the Page Length for fanfold.
Defines the separation in 1/6inches from the
top edge of a fanfold to the first print line.
Define the separation in inches from the
bottom edge of a fanfold to the last print line.
Use’s Manual
FUJITSU DL3100
Paper Setup
Valid Settings
Function
0, 1, 2, 3, 4, 5, 6, 7, Compensation value added to Fanfold Left
Fanfold Left
8,9,10,11,12,13,14,1 Mrg.
Mrg (1/180inch)
5,16,17,18,19,20
0, 1, 2, 3, 4, 5, 6, 7,
Fanfold Top
8,9,10,11,12,13,14,1 Compensation value added to Fanfold Top.
Mrg (1/180inch) 5,16,17,18,19,20,21,
22,23,24,25,26,27,28
Yes: The printer loads paper to the first
printing position automatically when using
Fanfold Auto
fanfold.
No, Yes
Load
No: Press the【Load/Eject】key to load
paper when using fanfold.
Skips printing on perforation area.
Only valid to fanfold.
Skip
No, Yes
Yes: Blank lines between 2 pages.
No: No blank lines between 2 pages.
Auto: Form Feed command from the host
causes the printer to advance the paper to the
tear-off position. Printing resumes on the
TOF on next page.
Tear
Manual: After the completion of a print job,
press a panel key to advance the paper to the
Auto, Manual, View, tear-off position.
Auto@FF
View: No incoming print data in 1~2 seconds
after printing completed causes the printer to
advance the paper by 2 lines. Printing
resumes 2 lines below the torn edge.
Auto@FF: a formfeed command is necessary
to auto feed the form to tear position.
Paper End
Detect
Yes: The printer stops printing if out of
paper.
No, Yes
No: The printer continues printing even out
of paper.
Disable: No compression on the print line
exceeding the printable width.
Compress
Disable, 11:8,
13.6:8, Auto
Auto: The print squeezes an over-width print
line (not exceeding 22" in contents) to the
printable width.
Other Compression Ratio: For example, a
ratio of 11: 8 commands the printer to take
this line compression ratio.
Use’s Manual
5-5
FUJITSU DL3100
Paper Setup
Valid Settings
Function
**Remark: The compression is disabled after
printer reset or loading a new page.
Determines if the cut sheet is jammed or
skew.
PaperCheck
Invalid, Anti-jam,
Anti-skew, Valid
Invalid: Disables the detection of both.
Anti-jam: Detect paper jam only.
Anti-Skew: Detect paper skew only.
Valid: Enables the detection of both.
No: Buzzer does not sound if out of paper.
Buzzer
No, Yes
Yes: Buzzer sounds if out of paper.
This printer saves the tear-off position before
switched off. After switched on, the printer if
any change in the tear-off position and
determines the start printing position.
Invalid: Printing starts from previously
switched off position.
Tear Position
Invalid, Detect,
Record
Detect: If the tear-off position is unchanged
or smaller, printing starts from TOF position.
If larger, printing starts from previously
switched off position.
Record: If the tear-off position is unchanged,
printing starts from TOF position. If
changed, printing starts from previously
switched off position.
Yes: Measures the width of the paper
automatically after loading the paper.
No: Disables page width measurement.
NOTE:
APW (Auto
Paper Width
detection)
No, Yes
The printer is equipped with a page width
sensor called “APW”.
If the sensor is defective, the “APW” setting
will not appear in the menu; The【Power】
LED blinks, 【Font 1】and【Font 2】have
no change,【Online】LED is off.
BlackMark
5-6
No, Yes
No: Disables black mark sensor.
Yes: Enables black mark sensor.
When “Yes” and online, pressing the【Tear
Off】 key advances the paper to the tear-off
position.
Use’s Manual
FUJITSU DL3100
Paper Setup
Valid Settings
Function
BlackMark commands: (also see section 5.7)
• 1D 0C:
Feeds paper to the print position
designated by the black mark. Advance
the paper to the tear-off position after
printing.
• 1C 28 4C 03 00 42 m:
m = 0: feeds paper to the print position
designated by the black mark.
m = 1: feeds paper to the black mark tearoff position.
8.0inch: The maximum print width is 80
columns of 10cpi PICA characters.
Width
FormLen
MicroAdj
Bail mode
Roll Paper
Use’s Manual
8.0inch, PaperWidth
Paper Width: Sets the detected page width as
print width. Enabling APW is required.
-20 -19 -18 -17 -16 15 -14 -13 -12 -11 10 -9 -8 -7 -6 -5 -4 - Fine tunes the form-length by n/360"
3 -2 -1 0 +1 +2
(0.07mm) based on the default value. (Valid
+3 +4 +5 +6 +7 +8
for single papers and fanfolds.)
+9 +10 +11 +12 +13
+14 +15 +16 +17
+18 +19 +20
The bail mode presses the paper against the
print platen during printing, but it is released
for paper loading.
Invalid: If you uninstall the lever or want to
disable the function, set this setting to
“invalid”.
Standard: Release the lever for paper loading
and lower the lever to press the paper against
Invalid, Standard,
the platen during printing.
Special
Special: When the paper is in tear-off
position, after the printer received printing
data, the printer will judge whether tear-off
was implemented first. If tear-off was
implemented and printing position is in lever
area, then the printer will press the lever; If
tear-off was not implemented, the printer will
not press the lever.
In friction mode, 【LF/FF】will not eject
the paper and feed to next page. (Assume roll
No, Yes
paper)
5-7
FUJITSU DL3100
Interface Setup
Interface setup
PnP
Valid Settings
No, Yes
Function
No: Disables plug and play for USB
Yes: Enables plug and play.
USB ID
No, Yes
No: Disables USB ID.
Yes: Enables USB ID
Character Setup
Character
setup
Valid Settings
Italic, Graphic
Character
Table
Function
Italic: Selects standard character sets.
Please refer to UG for details.
Graphic: Selects IBM character sets.
Please refer to UG for details.
Group 1, Group 2
Character
Group
The interpretation of ASCII codes
between 0x80~0x9F:
Group 1: as control codes.
Group 1: as printable characters.
Int'l Char Set
HS-Draft
Font
Pitch (cpi)
5-8
USA, France, Germany,
UK, DenmarkI, Sweden,
Italy, SpainI, Japan,
Norway, DenmarkII,
Spain II, LatinAm,
Denmark, China
No, Yes
International character set selections
Yes: Prints High Speed Draft when Draft
font is selected.
Daft, DraftCond, Roman,
Sans Serif,
Selects the font.
Courier, Prestige,
Script, OCR B, OCR A,
Orator, Gothic, Souvenir
10, 12, 15, 16.6, 17.1, 20, Controls the characters per inch setting.
24, PS
Use’s Manual
FUJITSU DL3100
Code Page
CP437, CP737,
CP850, CP851,
CP852, CP857,
CP858, CP860,
CP861,CP863,
CP864, Extend864,
CP865, CP866,
Bulgaria866,
CP1250, CP1251,
CP1252, CP1253,
CP1254, 8859_1,
8859_1SAP, 8859_2,
8859_5, 8859_7,
8859_9, 8859_15,
BRASCII, Abicomp,
Roman8,
CoaxTwinax,
New437,
NewDig850,
Code page selections
OldCode860,
Flarro863,
Hebrew865,
CP1257,
Ukraine866,
Kazakhst866,
Kamenicky,
Mazovia, Baltic775,
CROASCII, Farsi,
Urdu, GreekDEC,
ELOT928,
UK_ASCII,
US_ASCII, Swedish,
German, Portuguese,
French, Italian,
Norwegian, Spanish,
SiemensTurk,
DECTurkish
Sets the height for 15CPI character.
15cpi Style
Small, Normal
Small: prints in 1/8” height
Normal: prints in full height
AGM (IBM)
Use’s Manual
No, Yes
Activates or deactivates the AGM
(Alternative Graphics Mode) mode in
IBM emulation
5-9
FUJITSU DL3100
Other Setup
Other setup
Valid Settings
Form Length
Ctrl
No, Yes
Function
No: Form length commands are invalid in
neither of the emulation.
Yes: Form length commands are valid in either
of the emulations.
Print Speed
Ctrl
No, Yes
No: Print speed commands are invalid in
neither of the emulation.
Yes: Print speed commands are valid in either
of the emulations.
Pitch Ctrl
No, Yes
No: Ignores CPI commands
Yes: CPI commands are valid
Font Ctrl
No, Yes
No: Ignores font select commands
Yes: font select commands are valid
5-10
Use’s Manual
FUJITSU DL3100
German (Deutsch)
Systemeinstellung
Sprache
Emulation
Auto CR (ESC/P2)
Auto CR (IBM)
Auto LF
Druck Dir
Tabellenlinien
Null
Textqualität
Ersetze 1. Nadel
Ersetze 2. Nadel
Energiesparmodus
Mehrlagiges Drucken
Impact Mode
Graphikgeschw.
Use’s Manual
Gültige Werte
English, deutsch, Poccия, Italiano, Français, Español,
Türkçe, Português
ESC/P2, IBM
Nein, Ja
Nein, Ja
Nein, Ja
Bi-Dir, Uni-Dir
Gestrichelt, Verbunden, Gepunktet, Deaktiviert
0, Ø
LQ, NLQ
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
Aus, 1min, 2min, 5min, 10min
Ungültig, Standard, Verstärkt
Normal, Stark
Normal, Schnell, Ultra
5-11
FUJITSU DL3100
Papier Setup
Einzel Länge
Einzel Ob Rand
Einzel Unt Rand
Einzel Li Rand
Einzel Ob Rand Fein
Einzel Auto laden
Endlos Form länge
Endlos Ob Rand
Endlos Unt Rand
Endlos Li Rand
Endlos Ob Rand Fein
Endlos Auto Laden
Perforationssprung
Abreißen
Papierendeerkennung
Komprimieren
Papierhandhabung
Summer
Abreißposition
APW
BlackMark
Druckbreite
FormLäng Fein
Andruckbügelmodus
Rollenpapier
Gültige Werte
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4,
B4, Definiert
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Ungültig, 0.5sec, 1sec, 1.5sec, 2sec
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4,
B4, Definiert
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definiert
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Nein, Ja
Nein, Ja
Auto, Manuelles, Kurz, Auto@FF
Nein, Ja
Ungültig, 11: 8, 13.6: 8, Auto
Aus, Anti-Stau, Anti-Schräg, Ein
Nein, Ja
Nein, Erkennen, Speichern
Nein, Ja
Nein, Ja
8.0inch, Papierbreite
-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Ungültig, Standard, Spezial
Nein, Ja
Schnittstellen Setup
PnP
USB ID
Zeicheneinstellung
Zeichentabelle
PC-Zeichensatz
Land
HS-Draft
Schriftart
Laufweite (cpi)
5-12
Gültige Werte
Nein, Ja
Nein, Ja
Gültige Werte
Italic, Graphic
Gruppe 1, Gruppe 2
USA, Frankreich, Deutschland, U.K., Dänemark
Ⅰ,
Schweden, Italien, Spanien
II, Spanien II, Lat-Amerika, Dänemark, China
Nein, Ja
Draft, DraftCond, Roman, Sans Serif, Courier, Prestige,
Script,
OCR B, OCR A, Orator, Gothic, Souvenir
10, 12, 15, 16.6, 17.1, 20, 24, PS
Use’s Manual
FUJITSU DL3100
Zeicheneinstellung
Zeichensatz
15cpi Stil
AGM (IBM)
Gültige Werte
CP437, CP737, CP850, CP851, CP852, CP857, CP858,
CP860, CP861, CP863, CP864, Extend864, CP865, CP866,
Bulgaria866, CP1250, CP1251, CP1252, CP1253, CP1254,
8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7, 8859_9,
8859_15, BRASCII, Abicomp, Roman8, CoaxTwinax,
New437, NewDig850, OldCode860, Flarro863, Hebrew865,
CP1257, Ukraine866, Kazakhst866, Kamenicky, Mazovia,
Baltic775, CROASCII, Farsi, Urdu, GreekDEC, ELOT928,
UK_ASCII, US_ASCII, Swedish, German, Portuguese,
French, Italian, Norwegian, Spanish, SiemensTurk,
DECTurkish
Schmal, Normal
Nein, Ja
Erweitertes Setup
Formularlänge Strg
Geschwindigkeit Strg
Laufweite Strg
Font Strg
Uni-dir Strg
Use’s Manual
Gültige Werte
Nein, Ja
Nein, Ja
Nein, Ja
Nein, Ja
Nein, Ja
5-13
FUJITSU DL3100
Russian (Россия)
обновление системы
язык
Эмуляция
Авто CR ( ESC/P2)
Авто CR (IBM)
Авто LF
Направленниe пeчати
Контурная линия
Hoлb
Текcт кaчecтва
Заменa 1. иглы
Заменa 2. иглы
Экономный режим
Многослойная печать
вoздействия
Скорость печати
5-14
Правильные значения
English, Deutsch, Poccия, Italiano, Français, Español,
Türkçe, Português
ESC/P2, IBM
НET, ДA
НET, ДA
НET, ДA
oднoнaпpB, дByнaпpB
отключен, Подключен, лyнктиpнaя, безпечати
0, Ø
LQ, NLQ
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
выключенo, 1мин, 2мин, 5мин, 10мин
недейств, Обычный, усилен
Hopmaльнo, сильнo
Hopmaль, быстро, yльтpa
Use’s Manual
FUJITSU DL3100
Настройка стpaницы
Длина форм лист
Сверху oтступ Лист
Снизу oтступ Лист
Слева oтступ Лист
Веpx отс. Л. Тонко
Автом Загруз Лист
Длина форм Непрер
Сверху oтступ Непрер
Снизу oтступ Непрер
Слева oтступ Непрер
Веpx отс. Тонко Непр
Автом загруз Непрер
Пропуск перфорации
Отрыв бумаги
Oлpeдел конeц бумаг
Сжатие
Обpaшeниe c бумагой
Сигнал
Позиции отрыва
Oлpeд ширины бумаги
черной метки
Ширина печати
Микродлинформ бумаг
Moд.лpижимн.Cкoбa
Pyлoннaя бумагa
Правильные значения
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, oлpeделeн
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, oлpeделeн
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, oлpeделeн
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, oлpeделeн
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
нeдейств, 0.5sec, 1sec, 1.5sec, 2sec
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, oлpeделeн
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, oлpeделeн
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, oлpeделeн
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, oлpeделeн
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
НET, ДA
НET, ДA
Авто, ручной, короткий, Авто@FF
HET, ДA
Недейств, 11: 8, 13.6: 8, Auto
Лoдключен, Aнти-застой, Aнти-cклoн, отключен
HET, ДA
Лoдключен, oлpeдениe, запись
НET, ДA
НET, ДA
8.0inch, Ширина бумаги
-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4
-3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20
Нeдoлyстимo, стaндapт, Cлeциaлbнo
НET, ДA
Настройка интерфейс
PnP
USB ID
Настройка
знаков
Taблицa знаков
Группа символов
Набор знаков
Bbl c o3aд
Use’s Manual
Правильные значения
НET, Да
НET, Да
Правильные значения
Italic, Graphic
Группа I, группа 2
CШA, фpaнция, Гepмaния, U.K., Дания, Швеция,
итaпия,
испания, япoния, Норвегия, Дания II, испания II, Лат
Америка, Данияя, Китай
НET, Да
5-15
FUJITSU DL3100
pkopocтb
Настройка
знаков
Шpифт
Шаг
(cpi)
Koдoвaя cтpaницa
Cпocoб пeчaтc 15 cpi
AGM (IBM)
Правильные значения
Draft, DraftCond, Roman, Sans Serif, Courier, Prestige,
Script, OCR B, OCR A, Orator, Gothic, Souvenir
10, 12, 15, 16.6, 17.1, 20, 24, PS
CP437, CP737, CP850, CP851, CP852, CP857, CP858,
CP860, CP861, CP863, CP864, Extend864, CP865,
CP866, Bulgaria866, CP1250, CP1251, CP1252, CP1253,
CP1254, 8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7,
8859_9, 8859_15, BRASCII, Abicomp, Roman8,
CoaxTwinax, New437, NewDig850, OldCode860,
Flarro863, Hebrew865, CP1257, Ukraine866,
Kazakhst866, Kamenicky, Mazovia, Baltic775,
CROASCII, Farsi, Urdu, GreekDEC, ELOT928,
UK_ASCII, US_ASCII, Swedish, German, Portuguese,
French, Italian, Norwegian, Spanish, SiemensTurk,
DECTurkish
Meпкий, Обычный
НET, Да
Другие настройки
длинa формyляp Ctrl
скорости Ctrl
Шaг Ctrl
ШpиФт Ctrl
однонаправленной Ctrl
5-16
Правильные значения
HET, Да
НET Да
НET, Да
НET, Да
НET, Да
Use’s Manual
FUJITSU DL3100
Italian (Italiano)
Setup sistema
Linguaggio
Emulazione
Auto CR (ESC/P2)
Auto CR (IBM)
Auto LF
Direz.Stampa
Linee Formato
Zero
Qualità di testo
Primo ago rotto
Secondo ago rotto
Risparmio Energia
Stampa multicopia
Modo Impatto
Veloc. Grafica
Imposta carta
Lunghezza Foglio
Margine Sup. Foglio
Margine Infer. Foglio
Regola foglio a SX
Regola Sup. Foglio
Autocarica foglio
Lungh. Mod.
Continuo
Margine Superiore
Mar. Inf. Continuo
Regola a SX continuo
Regola Sup. continuo
Autocarica continuo
Salto Perforazione
Strappo
Vede fine carta
Comprime
Gestione carta
Cicalino
Posizione STP
APW
Use’s Manual
Impostazioni Valide
English, Deutsch, Poccия, Italiano, Français, Español,
Türkçe, Português
ESC/P2, IBM
No, Si
No, Si
No, Si
Bi-Dir, Uni-Dir
Disconnessa, Connessa, riga aghi, Non stampa
0, Ø
LQ, NLQ
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
OFF, 1min, 2min, 5min, 10min
Non valido, Copia STD, più impatto
Normale, Pesante
Normale, Veloce, Ultra
Impostazioni Valide
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4,
B4, Definito
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Non valido, 0.5sec, 1sec, 1.5sec, 2sec
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4,
B4, Definito
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definito
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
No, Si
No, Si
Auto STP, STP manuale, STP corto, Auto@FF
No, Si
Non valido, 11:8., 13.6:8, Auto
Invalido, Non inceppa, Antiscivolo, Valido, ,
No, Si
Invalido, Rileva, Registra
No, Si
5-17
FUJITSU DL3100
Segno nero riferim
Larghezza stampa
Regola lung. Carta
Barra rullini
Rullo Carta
No, Si
8.0inch, Larghezza carta
-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3
-2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14
+15 +16 +17 +18 +19 +20
Non valido, Standard, Speciale
No, Si
Setup IF
PnP
ID USB
Impostazioni Valide
No, Si
No, Si
Imposta caratteri
Tabella Caratteri
Gruppo Carattere
Set Carat. Int.
HS-Bozza
Fonte
Spaziatura (cpi)
Impostazioni Valide
Italico, Grafica
Groupo 1, Group 2
USA, Francia, Germania, Regno Unito, Danimarca I,
Svezia, Italia, Spagna I, Giappone, Norvegia, Danimarca
II, Spagna II, Danimarca, Porcellana
No, Si
Draft, DraftCond, Roman, Sans Serif, Courier, Prestige,
Script, OCR B, OCR A, Orator, Gothic, Souvenir
10, 12, 15, 16.6, 17.1, 20, 24, PS
Imposta caratteri
Code Page
Stile 15 CPI
AGM (IBM)
Impostazioni Valide
CP437, CP737, CP850, CP851, CP852, CP857, CP858,
CP860, CP861, CP863, CP864, Extend864, CP865,
CP866, Bulgaria866, CP1250, CP1251, CP1252, CP1253,
CP1254, 8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7,
8859_9, 8859_15, BRASCII, Abicomp, Roman8,
CoaxTwinax, New437, NewDig850, OldCode860,
Flarro863, Hebrew865, CP1257, Ukraine866,
Kazakhst866, Kamenicky, Mazovia, Baltic775,
CROASCII, Farsi, Urdu, GreekDEC, ELOT928,
UK_ASCII, US_ASCII, Swedish, German, Portuguese,
French, Italian, Norwegian, Spanish, SiemensTurk,
DECTurkish
Piccolo, Normale
No, Si
Altri Setup
Comando lunghezza
Comando velocità
Comando Spaziatura
Comando Fonte
5-18
Impostazioni Valide
No, Si
No, Si
No, Si
No, Si
Use’s Manual
FUJITSU DL3100
Comando stampa mono
No, Si
French (Français)
Configuration Système
Language
Emulation
RC-Auto (ESC/P2)
RC-Auto (IBM)
SL-Auto
Dir Impr
Ligne forméà
Zéro
Qualité du texte
Changer aiguille 1
Changer aiguille 2
Economie Energie
Impr. multi-copies
Mode Impact
Vitesse graphiq
Use’s Manual
Paramètres Valides
English, Deutsch, Poccия, Italiano, Français, Español,
Türkçe, Português
ESC/P2, IBM
Non, Oui
Non, Oui
Non, Oui
Bidir, Unidir
Discontinue, Continue, Pointillé, Non imprime
0, Ø
LQ, NLQ
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
18, 19, 20, 21, 22, 23, 24
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
18, 19, 20, 21, 22, 23, 24
Non, 1mn, 2mn, 5mn, 10mn
Non, Standard, Renforcé
Normal, Fort
Normal, Rapide, Ultra
5-19
FUJITSU DL3100
Réglage papier
Feuille LongPage
Bord Sup. Feuille
Bord Inf. Feuille
Marge Gauche Feuille
Marge Haute Feuille
Charg. Auto Feuille
Listing LongPage
Listing Bord Sup.
Listing Bord infér.
Listing Marge Gauche
Listing Marge Haute
Listing Charg. Auto
Saut perforation
Coupe
Détect. Fin Papier
Condense
Gestion Papier
Alarma
Position de Coupe
APW
Mode Repère Noir
Largeur Impression
LongPag Micro-ajust
Mode entrainement
Papier du rouleau
Paramètres Valides
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, Définie
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Définie
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Définie
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, c
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Non, 0.5sec, 1sec, 1.5sec, 2sec
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, Définie
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Définie
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1,Définie
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Définie
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Non, Oui
Non, Oui
Auto, Manuelle, Courte, Auto@FF
Non, Oui
Non, 11:8, 13.6:8, Auto
Non, Bourrage, Anti-biais, Oui,
Non, Oui
Non, Détecter, Enregistrer
Non, Oui
Non, Oui
8.0inch, Larg.Papier
-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5
-4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
19 20
Non Valid, Standard, Spécial
Non, Oui
Config Interface
PnP
USB ID
Parametrage Caractere
Table Caractère
Groupe Caractères
Pays
HS-Draft
Fonte
Espacement (cpi)
5-20
Paramètres Valides
Non, Oui
Non, Oui
Valid Settings
Italic, Graphic
Groupe 1, Groupe 2
USA, France, Allemagne, Royaume-Uni, Denmark
Ⅰ,
Suède, Italie, Espagne, Japon, Norvège, Denmark
Ⅱ,
Espagne
Ⅱ, Ameriquelat,
Non, Oui
Draft, DraftCond, Roman, Sans Serif, Courier, Prestige,
Script, OCR B, OCR A, Orator, Gothic, Souvenir
10, 12, 15, 16.6, 17.1, 20, 24,PS
Use’s Manual
FUJITSU DL3100
Parametrage Caractere
Code Page
Style15cpi
AGM (IBM)
Valid Settings
CP437, CP737, CP850, CP851, CP852, CP857, CP858,
CP860, CP861, CP863, CP864, Extend864, CP865,
CP866, Bulgaria866, CP1250, CP1251, CP1252, CP1253,
CP1254, 8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7,
8859_9, 8859_15, BRASCII, Abicomp, Roman8,
CoaxTwinax, New437, NewDig850, OldCode860,
Flarro863, Hebrew865, CP1257, Ukraine866,
Kazakhst866, Kamenicky, Mazovia, Baltic775,
CROASCII, Farsi, Urdu, GreekDEC, ELOT928,
UK_ASCII, US_ASCII, Swedish, German, Portuguese,
French, Italian, Norwegian, Spanish, SiemensTurk,
DECTurkish
Petit, Normal
Non, Oui
Autre réglage
Ctrl LongPage
Ctrl Vitesse Impr.
Ctrl Espacement
Ctrl Fonte
Ctrl Impr. Uni-Dir
Use’s Manual
Paramètres Valides
Non, Oui
Non, Oui
Non, Oui
Non, Oui
Non, Oui
5-21
FUJITSU DL3100
Spanish (Español)
Menu. Sistema
Lenguage
Emulación
Auto CR (ESC/P2)
Auto CR (IBM)
Auto LF
Direccion Imp
Linea del Formato
Cero con barra
Sust. 1er pin roto
Sust. 2do pin roto
Modo Ahorro Energía
Impr. Multi-Copias
Modo de Impacto
Imp.Grafica
5-22
Ajustes validos
English, Deutsch, Poccия, Italiano, Français, Español,
Türkçe, Português
ESC/P2, IBM
No, Si
No, Si
No, Si
Bi-Dir, Uni-Dir
Desconect, Conectado, Línea Punto, Sin Impr.
0, Ø
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
18, 19, 20, 21, 22, 23, 24
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
18, 19, 20, 21, 22, 23, 24
OFF, 1min, 2min, 5min, 10min
Inválido, Cop. Normal, Cop. Fuerte
Normal, Fuerte
Normal, Rapido, Ultra
Use’s Manual
FUJITSU DL3100
Config. Papel
Tam. Hojas Sueltas
Margen Sup.Hoja S.
Margen Inf.Hoja S.
Margen Izq. Hoja S.
Margen. Sup. Hoja S.
Carga Auto. Hoja S.
Tam. Papel Continuo
Mar. Sup. Pap. Con.
Mar. Inf. Pap.Cont.
Marg. Iz. Pap. Cont.
Marg. Sup. Pap. Cont.
Carga Auto. Hoja Su.
Salto perforación
Corte
Detec. Fin de Papel
Condensado
Manejo de Papel
Alarma
Posición de Corte
Det. Ancho de Papel
Modo Marca Negra
Ancho de Impresión
Micro-Aju. Tam. Hoja
Modo barra
Rollo de Papel
Ajustes validos
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Invalido, 0.5seģ, 1seģ, 1.5seģ, 2seģ
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
No, Si
No, Si
Automatico, Manual, Corto, Auto@FF
No, Si
Inválido, 11:8, 13.6:8, Auto
Inválido, Anti-atasco, Anti-desvío, Válido,
No, Si
Inválido, Detectar, Registrar
No, Si
No, Si
8.0inch, Ancho de Papel
-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4
-3
-2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14
+15 +16 +17 +18 +19 +20
Inválido, Estandar, Espécial
No, Si
Conf. Interface
PnP
USB ID
Use’s Manual
Ajustes validos
No, Si
No, Si
5-23
FUJITSU DL3100
Menu. Carácter
Tabla de Caracter
Grupo de Caracter
Juego Carácter Int.
Alta Velocidad
Fuente
Tamaño Letra (cpi)
Pagina Codigos
Estilo15cpi
AGM (IBM)
Ajustes validos
Italico, Graficos
Grupo 1, Grupo 2
EEUU, Francia, Alemania, Reino Unido, Dinamarca
Ⅰ,
Suecia, Italia, España, Japón, Noruega, Dinamarca
Ⅱ,
España
Ⅱ, AméricaLat, D
No, Si
Draft, DraftCond, Roman, Sans Serif, Courier, Prestige,
Script, OCR B, OCR A, Orator, Gothic, Souvenir
10, 12, 15, 16.6, 17.1, 20, 24, PS
CP437, CP737, CP850, CP851, CP852, CP857, CP858,
CP860, CP861, CP863, CP864, Extend864, CP865,
CP866, Bulgaria866, CP1250, CP1251, CP1252, CP1253,
CP1254, 8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7,
8859_9, 8859_15, BRASCII, Abicomp, Roman8,
CoaxTwinax, New437, NewDig850, OldCode860,
Flarro863, Hebrew865, CP1257, Ukraine866,
Kazakhst866, Kamenicky, Mazovia, Baltic775,
CROASCII, Farsi, Urdu, GreekDEC, ELOT928,
UK_ASCII, US_ASCII, Swedish, German, Portuguese,
French, Italian, Norwegian, Spanish, SiemensTurk,
DECTurkish
Pequeno, Normal
No, Si
Config. Otros
Cmd. Long. de Hoja
Cmd. Vel. Impresión
Cmd. Tamaño Letra
Cmd.Fuente
Cmd. Imp. Uni-dir
5-24
Ajustes validos
No, Si
No, Si
No, Si
No, Si
No, Si
Use’s Manual
FUJITSU DL3100
Turkish (Türkce)
Sistem Ayar Durumu
Lisan
Emülasyon
Otom. Satırbaşı
(ESC/P2)
Otom. Satırbaşı (IBM)
Otom. Satır besleme
Baskı Yönü
Kağıt satırı
Sıfır Sayısı
metin Kalite
Sistem Ayar Durumu
Arızalı 1. iğne yed.
Arızalı 2. iğne yed.
Enerji tutumu modu
Çok katmanlı baskı
Vuruf modu
Grafik Hızı
Use’s Manual
Valid Settings
English, Deutsch, Poccия, Italiano, Français, Español,
Türkçe, Português
ESC/P2, IBM
Hayır, Evet
Hayır, Evet
Hayır, Evet
Ÿki-Yöne, Tek-Yöne
Bağlı değil, Bağlandı, Nokta satır, Baskı yok
0, Ø
LQ, NLQ
Valid Settings
Hayır, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
18, 19, 20, 21, 22, 23, 24
Hayır, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17,
18, 19, 20, 21, 22, 23, 24
OFF, 1min, 2min, 5min, 10min
Geçersiz, Normal, Güçlü
Normal, Güçlü
Normal, Hızlı, Ultra
5-25
FUJITSU DL3100
Kağıt Ayarı
Tek-kağıt Form uzun
Tek-kağıt Üst boşluk
Tek-kağıt Altkenar
Tek-kağıt Sol ayar
Tek-kağıt Üst ayar
Tek-kağıt oto kağıt
Sür. Form Kğt Uz.
Sür.Form Kğt Üst
Sür.Form Kğt Alt
Sür.Form Kğt Sol
Sür.Form Kğt üst
Sür. Form Oto Kğt
Delik atlama
Kağıt kesme
Sayfa sonu algı
Gnş Baskı sıkıştma
Eğrilik önleme
Ikaz
Kğt Kesme Poz.Sakla
Kağıt gen.algı
Siyah Çizgi algı
Baskı Genişliği
Kğt uznlk ince ayar
Basınç yay modu
Rulo kağıt
Geçerli ölçüler
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, Oto. Tanım.
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto. Tanım.
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto. Tanım.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Oto. Tanım.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Geçersiz, 0.5sec, 1sec, 1.5sec, 2sec
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14,
A4, B4, Oto. Tanım.
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto. Tanım.
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Oto. Tanım.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Oto. Tanım.
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Hayır, Evet
Hayır, Evet
Oto. kesim, Elle kesim, Kısa kesim, Auto@FF
Hayır, Evet
Geçersiz, 11:8, 13.6:8, Auto
Sıkışıklık, engel, Geçerli, Geçersiz
Hayır, Evet
Geçersiz, Algılama, Hafıza kayıt，
Hayır, Evet
Hayır, Evet
8.0inch, Kağıt genişliği
-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4
-3
-2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14
+15 +16 +17 +18 +19 +20
Geçersiz, Standart, Özel
Hayır, Evet
Arabirim Ayarı
PnP
USB Tanımı
5-26
Geçerli ölçüler
Hayır, Evet
Hayır, Evet
Use’s Manual
FUJITSU DL3100
Karakter Ayarı
Karakter Tablosu
Karakter Grubu
Karakter setleri
YБk.HHz-Tasiak
Yazı Tipi
Karakter Aralık (cpi)
Kod Sayfası
15cpi Biçimi
AGM (IBM)
Geçerli ölçüler
Italic,Graphic
Grup 1, Grup 2
Amerika, Fransa, Almanya, İngiltere, Danimarka I, İsveç,
İtalya, İspanya, Japonya, Norveç, Danimarka II, İspanya II,
Ltn Amerika, Danimarka, Çin
Hayır, Evet
Draft, DraftCond, Roman, Sans Serif, Courier, Prestige,
Script,
OCR B, OCR A, Orator, Gothic, Souvenir
10, 12, 15, 16.6, 17.1, 20, 24, PS
CP437, CP737, CP850, CP851, CP852, CP857, CP858,
CP860, CP861, CP863, CP864, Extend864, CP865, CP866,
Bulgaria866, CP1250, CP1251, CP1252, CP1253, CP1254,
8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7, 8859_9,
8859_15, BRASCII, Abicomp, Roman8, CoaxTwinax,
New437, NewDig850, OldCode860, Flarro863, Hebrew865,
CP1257, Ukraine866, Kazakhst866, Kamenicky, Mazovia,
Baltic775, CROASCII, Farsi, Urdu, GreekDEC, ELOT928,
UK_ASCII, US_ASCII, Swedish, German, Portuguese,
French, Italian, Norwegian, Spanish, SiemensTurk,
DECTurkish
Küçük, Normal
Hayır, Evet
Diğer Ayarlar
Kğt Uzunluk Komutu
Baskı Hızı Komutu
Karak.Aralık Kont.
YazıTipi Komutu
Tekyön bask Komutu
Use’s Manual
Geçerli ölçüler
Hayır, Evet
Hayır, Evet
Hayır, Evet
Hayır, Evet
Hayır, Evet
5-27
FUJITSU DL3100
Portuguese (Português)
Config. Sistema
Linguagem
Emulação
Auto CR (ESC/P2)
Auto CR (IBM)
Auto LF
Direção Imp.
Linha forma
Zero
Calidad del texto
Substituição Pino 1
Substituição Pino 2
Config. Sistema
Poupança Energia
Impr.Multi-Copias
Modo de Impacto
Imp. Grafica
5-28
Valores válidos
English, Deutsch, Poccия, Italiano, Français, Español,
Türkçe, Português
ESC/P2, IBM
Não, Sim
Não, Sim
Não, Sim
Bi-Dir, Uni-Dir
Desativar, Ativar, Tracejada, No Imprimir
0, Ø
LQ, NLQ
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
No, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24
Valores válidos
OFF, 1min, 2min, 5min, 10min
Desativo, Cop.Normal, Cop.Forte
Normal, Forte
Normal, Rápido, Ultra
Use’s Manual
FUJITSU DL3100
Config. Papel
Tam.Folha Solta
Margem Topo Folha
Margem Inf. Folha
Margem Esq. Folha
Margem Dir. Folha
Carreg. Auto Folha
Tam. Form. Cont.
Mar. Topo Form. Cont.
Mar. Inf. Form. Cont.
Mar. Esq. Form. Cont.
Marg. Topo Form. Cont.
Carreg. Auto Form
Salte perfuração
Corte
Detec. Fim de Papel
Condensado
Manuseio de Papel
Cigarra
Posição de corte
Det. Largura Papel
Modo Marca Preta
Largura impressão
Mic. -Aju. Tam. Hoja
Modo de pressão
Rollo de Papel
Valores válidos
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4,
B4, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Desativo, 0.5sec, 1sec, 1.5sec, 2sec
2.5, 11/4, 3, 3.5, 11/3, 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 14, A4,
B4, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
0, 1/6, 1/4, 1/3, 1/2, 2/3, 3/4, 1, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, Definido
-7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7
Não, Sim
Não, Sim
Automático, Manual, Corto, Auto@FF
Não, Sim
Desativo, 11:8, 13.6:8, Auto
Inválido, Anti-atola, Anti-desvio, Válido
Não, Sim
Inválido, Detectar, Registrar
Não, Sim
Não, Sim
8.0inch, largura do papel
-20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 3
-2 -1 0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +10 +11 +12 +13 +14
+15 +16 +17 +18 +19 +20
Invalido, Norma, Especial
Não, Sim
Conf. Interface
PnP
ID USB
Use’s Manual
Valores válidos
Não, Sim
Não, Sim
5-29
FUJITSU DL3100
Config. Caráter
Tabela de carateres
Grupo de Carateres
Conj. Carateres Int.
Alta Velocidad
Fonte
Passo (cpi)
Página de Código
Estilo 15cpp
AGM (IBM)
Valores válidos
Itálic, Gráfico
Group 1, Group 2
EUA, França, Alemanha, Reino Unido, Dinamarca I, Suécia,
Itália, Espanha, Japão, Noruega, Dinamarca II, Espanha II,
América Lat, Dinamarca, China
Não, Sim
Draft, DraftCond, Roman, Sans Serif, Courier, Prestige,
Script,
OCR B, OCR A, Orator, Gothic, Souvenir
10, 12, 15, 16.6,17.1, 20, 24,PS
CP437, CP737, CP850, CP851, CP852, CP857, CP858,
CP860, CP861, CP863, CP864, Extend864, CP865, CP866,
Bulgaria866, CP1250, CP1251, CP1252, CP1253, CP1254,
8859_1, 8859_1SAP, 8859_2, 8859_5, 8859_7, 8859_9,
8859_15, BRASCII, Abicomp, Roman8, CoaxTwinax,
New437, NewDig850, OldCode860, Flarro863, Hebrew865,
CP1257, Ukraine866, Kazakhst866, Kamenicky, Mazovia,
Baltic775, CROASCII, Farsi, Urdu, GreekDEC, ELOT928,
UK_ASCII, US_ASCII, Swedish, German, Portuguese,
French, Italian, Norwegian, Spanish, SiemensTurk,
DECTurkish
Pequeno, Normal
Não, Sim
Config. Outros
Cmd. Tam. de Folha
Cmd. Vel. Impresso
Cmd. Passo
Cmd. Fonte
Cmd. Imp. Uni- dir
5-30
Valores válidos
Não, Sim
Não, Sim
Não, Sim
Não, Sim
Não, Sim
Use’s Manual
FUJITSU DL3100
Black Mark
Paramenters
This printer uses tractors to load fanfold forms with pre-printed
black marks.
The printer requires 3 parameters to print on paper with black
marks:
1. Horizontal offset of black mark from the edge of page
(called Black Mark Physical Horizontal Position); later on,
this value facilitates the printer to locate its scanner
preparing for identifying the black marks.
2. Vertical offset of the first print line from the black mark
(called Distance Offset From BlackMark To Print
Position); later on, the print makes use of this value to
print the first line relative to the black mark.
3. Vertical offset of the tear-off edge from the black mark
(called Distance Offset From BlackMark To Tear
Position); this value informs the printer the tear-off
position of the page.
Not to skip or change the order of setting the above 3
parameters.
Use’s Manual
5-31
FUJITSU DL3100
The procedures to set the parameters:
1. Hold down the【Tear off】key while powering on the printer
and then release the key when the print head starts to move.
After loading paper, the printer prompts the Printer Settings
Printer Settings
[LF]=Next, [TEAR]=Back, [LOAD/EJECT]=OK,
[ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]=
Save and restart the printer.
System Setup
2. Press the Next or Back keys to scroll forward or backward
the sub-menus till the printer shows:
BlackMark Mode
3. Press OK to go into the BlackMark menu. The printer
prompts:
[Black Mark Adjustment Mode]
[LF]= Next, [TEAR]= Back,
[LOAD/EJECT]=OK,
[ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]=
Save and restart the printer.
Black Mark Physical Horizontal Position
Press any key to eject the paper, and load paper with black mark in
the Fanfold
Path.
4. The last prompt above advises you to press any key to unload
the dialog form. Then load a fanfold form with black mark.
5. Ensure to place the lever at
position. Then press the
【Load/Eject】key to load the black marked form. The top
edge of the form will then align with the printer’s tear-off blade.
Press Next or Back until you see the black mark marginally
exposed out of the tear-off blade. Then press OK to allow the
printer to scan the horizontal offset of the black mark relative to
the left edge of the page. (Meanwhile, the vertical position of
the black mark is measured and recorded.)
5-32
Use’s Manual
FUJITSU DL3100
When the printer fails to scan the horizontal offset (see the
below picture), it prompts you to repeat the above
procedures. If scanning is successful, it prompts:
Successfully setup black mark parameters.
Distance Offset From Black Mark To Print Position
6. The last prompt above invites you to set the next parameter -- vertical offset of the first print line from the black mark. Like
other setting dialogs, you have options:
1)to bypass this setting (by pressing Next or Back),
(WARNING: Not to skip or change the order in Black Mark
Setting.)
2)to accept the Distance Offset (by pressing OK),
3)to leave the subsequent settings (by press Exit),
4)to terminate the session and save modified parameter(s) (by
pressing Save and Restart).
7.When you respond with “OK” to set the vertical offset, the
printer prompts you to reload a black marked fanfold form:
Press any key to eject the paper, and load paper with black mark in
the Fanfold
Path.
The top edge of the form will then align with the printer’s
tear-off blade. Press Next or Back to feed or reverse-feed the
paper till the desired first print line position is reached. (With
the above measured vertical position, the printer will convert
the next paper feeding to the TOF relative to the black mark.)
Press OK to confirm the vertical offset. Then the print
prompts the invitation for setting the tear-off position relative
to the black mark:
Use’s Manual
5-33
FUJITSU DL3100
Successfully setup black mark parameters.
Distance Offset From Black Mark To Tear Position
8.When you respond with OK to set the tear-off position, the
printer prompts you to reload a black marked fanfold form:
Press any key to eject the paper, and load paper with black mark
in the Fanfold
Path.
The printer reloads the form. By default the form stops 5.5
inches away from the printer’s tear-off blade. Press Next or
Back to feed or reverse-feed the paper till the desired tear-off
position is reached. (With the above measured vertical
position, the printer will convert the net paper feeding to the
tear-off position relative to the black mark.) Press OK to
confirm the tear-off offset relative to the black mark. Finally,
press Save and Restart to save new settings and terminate
the session.
5-34
Use’s Manual
FUJITSU DL3100
Bidirectional
Alignment
When wiggling vertical grids appears in tabular reports, you
should adjust the Bidirectional Alignment. The procedures to
adjust bi-directional alignment across adjacent line grids:
1. Hold down the【Tear off】key while powering on the printer
and then release the key when the print head starts to move.
After loading paper, the printer prompts the Printer Settings.
Printer Settings
[LF]=Next, [TEAR]=Back, [LOAD/EJECT]=OK,
[ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]=
Save and restart the printer.
System Setup
2. Press the Next or Back keys to scroll forward or backward
the sub-menus till the printer shows:
Bi-directional Alignment
3. Press OK to go into the Bi-directional Test menu. The printer
prompts:
[Bi-direction Alignment]
[TEAR]=-1, [LF]=+1, [LOAD/EJECT]=OK, [ONLINE]=Back,
[ONLINE]+ [LOAD/EJECT]=Save and restart the printer
20
4. Every press on “+1” or “-1” shifts the second line to the right
or left, respectively, relative to the top line by 1 fine step.
After pressing “+1” twice and then “OK”, the printer
prompts:
22
Use’s Manual
5-35
FUJITSU DL3100
5. Repeat the adjustment till two grid lines align satisfactory as
“|”. Press “OK” again. The printer asks if you want to save the
correction:
Save the parameter settings ([LOAD/EJECT] or [ONLINE] = OK,
[LF] = Next)?
Yes
At this stage, you have the options to save or give up the
correction by pressing OK or Next, respectively. If you respond
with OK, an asterisk “*” appends to “Yes” to confirm saving
change. If you intend to give up the correction by pressing Next,
the printer prompts a “No” Then a confirmative response of OK
appends an asterisk “*” to the “No” prompt.
The printer then exits the Bi-directional Test and proceeds with
the next setup menu.
5-36
Use’s Manual
FUJITSU DL3100
Hex Dump
Beeps once to indicate going into hex dump mode:
Prints data from host in hexadecimal representation.
Pressing S4 suspends the printing.
When the hex dump has finished, pressing S4 forces the printing
of the last line of data, as any line termination control code from
host has no function.
Switch off the power to terminate the hex dump.
Use’s Manual
5-37
FUJITSU DL3100
Self Test / Status Page
5-38
Prints the printer settings and self-test pattern,show
as follow picture.
Use’s Manual
FUJITSU DL3100
Use’s Manual
5-39
FUJITSU DL3100
Printer Config Tool
In the CDROM is a software utility called “FUJITSU Printer Config
Tool”. This application enables a convenient, simple, and fast way to
control your printer without touching any keys on the operation panel.
1. Start the tool installation by double clicking the “FUJITSU Printer
Config Tool Setup.msi”.
2. Connect the printer to the system using USB or Parallel or Serial
cable
3. Power up the printer.
4. Run the tool from the Windows Start menu by selecting All
Programs, and then FUJITSU Printer Setup.
5. For more information on how to use the tool, go to the Help menu
and select User Guide.
Note: Ensure to disconnect the config tool before sending the
printing data,otherwise the data will not be printed or be
printed in a incorrect way.
5-40
Use’s Manual
FUJITSU DL3100
Customized Form
This printer allows the customization on the form length, TOF,
bottom margin and left margin for single sheets and fanfold.
Selecting the Define value(s) in section 5.2 (Paper Setup menu) allows the
printer to take up the customized page formatting value(s).
The parameter setting procedures involve:
1. The printer prompts the dialogs and you follow the prompts.
2. Before every measurement or change, the print instructs you to
unload the conversation form from the printer.
3. With the exception of measuring the form length for cut sheets,
always set the lever to the tractors position
4. For form length measurement, insert the customized form from
the proper paper path.
The other six settings are actually done on general fanfold forms --not the actual customized form. Fanfold paper gives direct visual
results on the TOF, bottom and left margins even though cut sheets
will be used in actual application.
This
chapter describes the following operations:
·Customize Cut Sheet Form Length
·Customize Cut Sheet TOF
·Customize Cut Sheet Bottom Margin
·Customize Cut Sheet Left Margin
·Customize Fanfold Page Formatting Parameters
Use’s Manual
6-1
FUJITSU DL3100
Customize Cut
Sheet Form
Length
1. Hold down both the【Online】and【Load/Eject】 keys
while powering on the printer and then release the keys
when the carriage initializes and beeps once. After loading
a form the printer prompts:
Customize Form
[LF]=Next ,[TEAR]=Back, [LOAD/EJECT]=OK,
[ONLINE]=Exit, [ONLINE]+[LOAD/EJECT]=
Save and restart the printer.
Single sheet
2. Press “OK” to start customizing all or part of 4 parameters
for single sheet. The printer prompts:
[Single sheet]
Form Length
3. You may skip to other customized settings by pressing
“Next” or “Back”. Once you press “OK” to continue with
form length measurement, the printer prompts:
1.Press any key to clear the Setup Instructions Page from the
printer. Insert
the Customized Page into the corresponding paper path. Press
[LOAD/EJECT] to
load and measure the page length.
2.The printer rolls over the entire Customized Page to measure
its length.
After measurement, press [LOAD/EJECT] to load a blank
Setup Instructions Page
to report the measured value.
3. Press [LOAD/EJECT] to save the measured value.Repeat the
above steps if the
6-2
Use’s Manual
FUJITSU DL3100
Illustrations for above step 1 and step 2.
Use’s Manual
6-3
FUJITSU DL3100
4. Follow the given prompt to unload the conversation form.
Load the customized form to allow the printer to scan the
page length. After the measurement, load another
conversation form to let the printer print out the measured
length.
The measured form length is: 11.0Inch, approximately equal to
279mm,
accuracy of plus or minus 0.1 inches.
The measured value has been saved. Remeasure
( [LOAD/EJECT]=OK, [ONLINE] =Exit)?
Yes
5.At this stage:
If【Load/Eject】is pressed, an asterisk “*” is appended to
“Yes” and you should repeat the procedures for form length
measurement as mentioned. Or,
If you input “Exit”, the printer saves the measurement value
and proceeds with the next customized setting.
6-4
Use’s Manual
FUJITSU DL3100
Customize Cut
Sheet TOF
1. After you follow through all the steps in 6.1 or you input
“Next” in step 3 in 6.1, the printer prompts:
Top Margin
2. You may skip to other customized settings by pressing
“Next” or “Back”. Once you press “OK” to continue with
customization of cut sheet TOF, the printer prompts:
Press any key to eject current page, load paper in the Fanfold
paper path, and then
proceed as follows:
[TEAR] = -(1/72) inch, [LF] = +(1/72) inch, [LOAD/EJECT]
= OK, [ONLINE] = Exit, [ONLINE] +
[LOAD/EJECT] = Save and restart the printer.
3. Follow the given prompt to unload the conversation form.
Ensure the lever is at
position. Then press the
【Load/Eject】key to load fanfold paper from tractors. The
top edge of the form initially aligns with the printer’s tearoff blade. You may input +/- 1/72” to adjust the TOF
position. When you get the desirable TOF, press OK or
Exit. The printer prompts the customized TOF value:
The defined position is: 4.2 mm.
Save the parameter settings ([LOAD/EJECT] or [ONLINE]=OK,
[LF]=Next)?
Yes
4. At this stage:
If【Load/Eject】is pressed, an asterisk “*” is appended to
“Yes” and you should repeat the procedures for form length
measurement as mentioned. Or,
If you input “Exit”, the printer saves the measurement value
and proceeds with the next customized setting.
Use’s Manual
6-5
FUJITSU DL3100
Customize Cut
Sheet Bottom
Margin
1.After you follow through all the steps in 6.2 or you input
“Next” twice in step 3 in 6.1, the printer prompts:
Bottom Margin
2. The remaining operations are nearly the same as
described in section 6.2. The only difference is to input +/1/72” till you get the desirable bottom margin.
Customize Cut
Sheet Left
Margin
1.After you follow through all the steps in 6.3 or you input
“Next” three times in step 3 in 6.1, the printer prompts:
Left Margin
2.The remaining operations are nearly the same as described
in section 6.2. The only difference is to input +/- 1/72” till
you get the desirable left margin.
6-6
Use’s Manual
FUJITSU DL3100
Customize
Fanfold Page
Formatting
Parameters
The customizations of the form length, TOF, bottom and left
margins for fanfold are exactly the same as describe. All you
need is to bypass the Single Sheet menu under Customize
Form. Follow step 1 in section 6.1:
Customize Form
[LF]=Next, [[TEAR]=Back, [LOAD/EJECT]=OK, [ONLINE]
=Exit, [ONLINE]+[LOAD/EJECT]=
Save and restart the printer.
Single sheet
Then hit “Next” instead to get into the fanfold parameter
menus:
[Tractor Paper]
Form Length
Refer section 6.1 to 6.4 for details on customizing the form
length, TOF, bottom margin, and left margin for fanfold.
Use’s Manual
6-7
FUJITSU DL3100
Life information printing
Holding down the jump key while starting up, feeding
paper,then the printer can print out the information
of consumables, as shown in the figure below:
6-8
Use’s Manual
FUJITSU DL3100
MAINTENANCE
Your printer requires very little care. Occasional
cleaning and replacement of the ribbon cartridge
are all that is required.
Cleaning is recommended approximately every 6 months or 300
hours of operation, whichever is sooner.
Lubrication of the printer is not usually necessary.
If the print head carriage does not move smoothly back and forth,
clean the printer in the manner described in this chapter. If the
problem continues, contact your dealer to determine whether
lubrication may be necessary.
The housing and the top cover of the printer help protect it against
dust, dirt, and other contaminants. However, paper produces small
particles that accumulate inside the printer. This section explains
how to clean and vacuum the printer and how to clean the paper bail
rollers.
It is easier to clean the printer when the cover is open.
This chapter describes the following content:
·Cleaning
·Cleaning the Platen(Paper Roller)
·Replace the ribbon
Use’s Manual
7-1
FUJITSU DL3100
CLEANING
Cleaning and Vacuuming the Printer
WARNING
To avoid any possibility of injury, before
cleaning the printer, turn off the power to
both the printer and the computer, and
unplug the printer.
CAUTION
The print head and metal frame is hot
during printing or immediately after
printing. Do not touch them until it cools
down.
Use the following procedure to clean and vacuum the
printer as required:
1.
2.
3.
Remove any paper from the printer. Make sure that the
power is off, and then disconnect the printer power cord.
Using a soft vacuum brush, vacuum the exterior of the
printer. Also vacuum the cut sheet edge.
Use a soft, damp cloth to wipe the exterior of the printer,
including the cover. A mild detergent may be used.
CAUTION
Do not use solvents, kerosene, or abrasive cleaning
materials that may damage the printer.
7-2
Use’s Manual

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 100
Producer                        : PDF Editor 2.2 - Foxit Software
Author                          : Zanvia
Create Date                     : 2018:03:30 09:52:34
Modify Date                     : 2018:03:30 09:52:34

EXIF Metadata provided by EXIF.tools