Fujitsu Network Communications LS103 2X2 MIMO, low power cellular base station User Manual User Guide

Fujitsu Network Communications, Inc. 2X2 MIMO, low power cellular base station User Guide

Users Manual

shaping tomorrow with you BroadOne™ LS110 Residential Femtocell Release 14 Issue 1, May 2015 FNC-LS110-0014-100User GuideFujitsu Network Communications Inc. Fujitsu and Fujitsu Customer Use Only https://partners.fnc.fujitsu.com
BroadOne™ is a trademark of Fujitsu NetworkCommunications Inc. (USA). All Rights Reserved.Buildex®, E-Z Ancor®, and Twist-N-Lock™ are registeredtrademarks or trademarks of Illinois Tool Works, Inc.Macintosh® is a registered trademark of Apple Computer, Inc.Microsoft® and Windows® are registered trademarks ofMicrosoft Corporation.All other products or services mentioned in this document are identified by the trademarks, service marks, or product namesas designated by the companies that market those products or services or own those marks. Inquiries concerning suchproducts, services, or marks should be made directly to those companies.This document and its contents are provided by Fujitsu Network Communications Inc. for guidance purposes only. Thisdocument is provided “as is” with no warranties or representations whatsoever, either express or implied, without notice, tomake including without limitation the implied warranties of merchantability and fitness for purpose. Fujitsu NetworkCommunications Inc. does not warrant or represent that the contents of this document are error free. Furthermore, thecontents of this document are subject to update and change at any time without notice by Fujitsu Network CommunicationsInc., since it reserves the right, changes in equipment design or components as progress in engineering methods maywarrant. No part of the contents of this document may be copied, modified, or otherwise reproduced without the expresswritten consent of Fujitsu Network Communications Inc.Fujitsu and Fujitsu Customer Use Only
Contents1 Welcome p. 52 Important Precautions p. 63 Exemptions and Liabilities p. 94 Customer Service p. 105 What's in the Box p. 116 Ports and Reset Button p. 127 LEDs p. 138 Before You Begin p. 149 Installation and Setup p. 159.1 Physically Mount the Product p. 169.1.1 Mount the Product on a Flat Surface p. 169.1.2 Mount the Product on a Wall p. 179.2 Connect the Product to a LAN Port p. 199.3 Connect the GPS Antenna p. 219.4 Connect the AC Adapter p. 229.5 Perform Initial Setup p. 2310 Reset the Product p. 2711 Troubleshooting p. 2912 Specifications p. 3213 Radio Frequency Energy p. 33User Guide Page 3BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
14 FCC Radio Frequency Emission p. 3415 Limited Warranty p. 3616 End-User License Agreement p. 3717 Open Source Software p. 4117.1 Guide to Micro Base Station Open Source Software p. 4217.2 Open Source Software Licensing p. 45User Guide Page 4BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
1WelcomeThank you for buying the BroadOne™ LS110 Residential Femtocell. The LS110 Residential Femtocell allows you toconnect your 4G LTE–capable devices, such as smartphones, tablets, and PCs, to the 4G LTE cellular network andthe Internet in areas where 4G LTE cellular signal strength is too weak or nonexistent. Think of the LS110 as a Wi-Fi hotspot for your 4G LTE network. The product is also GPS capable to support location-based services.This product can be used alone in a residential (home) environment, or it can be deployed in clusters in a small-business environment. Although your 4G LTE–capable devices connect to the LS110 wirelessly, the product itselfconnects to the cellular network and the Internet by way of a wired Ethernet connection (LAN cable) to yourrouter, modem, or other device used for connecting to the Internet.Important!Before using your new LS110 Residential Femtocell, read this entire manual to ensure that the product isinstalled and used correctly.To avoid personal injury or damage to the equipment, carefully read and adhere to the Important Precautions.About this User GuideThis manual assumes that you are familiar with the basic operations of Microsoft® Windows® and Macintosh®operating systems as well as mobile devices such as smartphones and tablets.Screens and illustrations shown in this manual may differ from the actual product. In some cases, minor details ora part of a screen may be omitted to help clarify a point.User GuideWelcomePage 5BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
2Important PrecautionsBefore using this product, please read and make sure you understand the following precautions. If you have anyquestions, contact Customer Support.Warning of 911 Limitations: Basic 911 and Enhanced 911 (E911) services may be limited in areas outsideof wireless network coverage. This device extends the reach of wireless network coverage in your area. Therefore,in the event of an electrical power outage, broadband connection failure, termination of broadband service, orother service disruption, you may not be able to make 911 calls using this device. Always be prepared to reportyour location to the 911 operator.Danger: Cell phones or other electronic devices that emit radio waves, including this product, mayaffect the operation of implanted pacemakers, implanted cardioverter-defibrillators, or otherelectronic medical devices. Therefore, it is important that you observe the following precautions whenoperating the product near such medical devices: • People with an implanted pacemaker or cardioverter-defibrillator should keep such devices atleast 9 inches away from their pacemaker or cardioverter-defibrillator.• Do not bring such devices into operating theaters, intensive-care units (ICUs), and coronary careunits (CCUs), and turn off such devices when entering hospital wards.• Even if you are in a lobby or waiting room, turn off such devices when there are electronic medicaldevices nearby.• When using electronic medical devices other than an implanted pacemaker and implantedcardioverter-defibrillator outside a medical institution (for example, home medical treatment),check individually with the manufacturer of the electronic medical device regarding the influenceof radio waves.Danger: Turn the product off near high-precision electronic devices, such as cardiac pacemakers,hearing aids, other electronic medical devices, fire alarms, and automatic doors. The radio wavesemitted by this product might adversely affect such devices. If you are using an electronic medicaldevice, contact the device manufacturer or retailer for information about the possible effect of radiowaves.Danger: If you experience any physical discomfort, such as itching or rashes, stop using the productimmediately, and consult a dermatologist. People with certain physical conditions may experiencesuch skin problems.User GuideImportant PrecautionsPage 6BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Danger: Do not leave within reach of small children. Mishandling by a small child could injure thechild.Danger: If you detect smoke, an abnormal odor or noise, excessive heat, or any other abnormalcondition from the product, immediately turn off the product, remove the cables from the product orPC, and check whether they are overheated. Then contact your dealer. Also, if you have dropped ordamaged the product in any way, do not continue to use it, and contact your dealer.Danger: Do not splash the product with water or other liquids, do not use in places subject to directsplashing with water or other liquids, do not touch the product with wet hands, and do not use inhumid areas, such as in a bathroom. Doing so might cause electric shock or fault from short-circuitingor corrosion of electronic circuits. If the product is splashed with liquid, immediately disconnect thepower plug! Faults caused by wetting with water or humidity are not covered by the warranty, andcharges will be incurred for repair.Danger: Do not expose the product to extreme heat, cold, dust, or humidity, and do not place theproduct in a microwave oven or pressurized vessel. Doing so might cause an ignition, rupture, fault,fire, or deformation.Danger: Do not use the product outside in an unprotected area. Exposure to snow, rain, or lightningrisks electric shock or other damage or injury.Danger: Do not touch the connection terminals. Doing so might cause electric shock, injury, or afault. Also, do not short-circuit the connection terminals or allow conductive foreign objects, such asmetal fragments or pencil lead, to come into contact with or get inside the connection terminals.Doing so might cause a fire or fault.Danger: Do not let metal straps, metal accessories, or other metal objects touch the power plug orconnection terminals. Doing so might cause fire, electric shock, injury, or a fault.Danger: Do not drop, throw, or hit the product. Any strong impact might cause rupture,overheating, ignition, leakage, or fault. If the product is damaged and its internal parts are exposed,do not touch the exposed parts with your hands. Doing so might cause electric shock or injury.Immediately unplug the product from the wall outlet, and contact your dealer.Danger: Do not disassemble, modify, or attempt to repair the product. Doing so might cause a fault,ignition, electric shock, or injury. Doing so also voids the warranty, and the Company is not liable forany damage to the product or devices used with the product. In addition, remodeling cell phones orelectronic devices that emit radio waves violates the Radio Law.Danger: Do not use power outlets or wiring apparatus beyond its rating. Also, connecting multipledevices to a single power strip could exceed its rating, thereby causing overheating and fire.Danger: The product may become hot through prolonged use, especially in a high-temperatureenvironment. Though not extremely hot, touching the product for a long time might cause low-temperature burns.Warning: Use only the supplied AC adapter. Using an AC adapter from another product coulddamage the product.User GuideImportant PrecautionsPage 7BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Warning: Do not place heavy objects on the AC adapter or pull on the cord. Doing so could damagethe cord. To avoid damaging the cord, plug the AC adapter power plug into an outlet near the productto keep the amount of exposed cord to a minimum, and ensure that the exposed cord is alwaysclearly visible.Warning: When not using the product for an extended period of time, unplug the AC adapter.Warning: Use only the specified peripheral cables. Using other types of cables might causeoverheating, ignition, rupture, fault, or leakage.Warning: Keep the connection terminals clean. Failure to do so may cause a fault.Warning: Do not leave the product on an unstable or tilted surface, such as on an unstable stand.The product may be damaged if it falls to the floor.Warning: Do not place the product directly on sand, dirt, or any similarly dirty surface. If sand or dirtgets inside the product, it might cause overheating or a fault.Warning: Do not place near corrosive chemicals or in places where corrosive gas is generated. Doingso might cause a fault or loss of internal data.Warning: Do not place the product close to magnetized objects, such as credit cards or floppy disks.Doing so might result in loss of recorded information.User GuideImportant PrecautionsPage 8BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
3Exemptions and LiabilitiesOne advantage of digital communications is that consistently high communications quality can be maintainedeven when the signal strength is weak. When the signal strength is too weak, however, communications can stillbe interrupted.Because this product uses radio waves, the possibility of your communications being intercepted by third partiescannot be eliminated.This product is intended for use in an office environment or at home as office automation equipment. As such, donot use this product for any purpose directly or indirectly related to human health and safety, such as withmedical equipment.If you use this product for a purpose that requires higher reliability than ordinary office automation equipment orcomputer systems, take proper steps to ensure safety and prevent system failures.The Company is not liable for any damages arising from earthquakes, lightning, storms, floods or other naturaldisasters, as well as fires, actions by third parties, other accidents, intentional or mistaken operation by thecustomer, or use under other unusual conditions outside the responsibility of the Company.The Company is not liable for any incidental damages (change/disappearance of described content, loss ofbusiness income, disruption of business, etc.) arising from use of or inability to use the product.The Company is not liable for any damages arising from failure to observe the described content of this manual.The Company is not liable for any damages arising, for example, from malfunction caused by combination withconnected devices or software not related to the Company.Setting data may sometimes be altered or lost due to faults, repair or other handling of the product. TheCompany is not liable for any damages or lost income resulting from recovery of these data.It is recommended that you keep a copy of important data in your PC's hard disk, etc. Whatever the cause of faultor malfunction may be, the Company assumes no responsibility for alteration or loss of saved information.User GuideExemptions and LiabilitiesPage 9BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
4Customer ServiceService and Repair InquiriesFor service and repair inquiries, contact your service provider for information.Backing Up Data Before RepairBefore sending the product for repair, be sure to back up any data in memory in case the memory is erasedduring repair. Note that the Company is not liable for any damages and loss of income resulting from altered orlost contents.Spare PartsThe Company retains performance parts for repair of the LS110 main unit and its peripherals for 6 years afterdiscontinuation of production. "Performance parts for repair" refers to parts required for maintaining the functionsof the product. If necessary, recycled parts that meet the Company's quality standards may be used for repair.User GuideCustomer ServicePage 10BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
5What's in the BoxIf any of the following items are missing from the box, contact customer service or the retail store from which itwas purchased:LS110 Residential Femtocell(shown with bracket attached)StandAC AdapterGPS AntennaAlso included in the box is a Quick Start Guide that may be used by experienced users for quick installation andsetup.User GuideWhat's in the BoxPage 11BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
6Ports and Reset ButtonGPS portIf the internal GPS antenna is unable to receive a GPS signal, plugthe supplied GPS antenna into this port, and place the antennaend of the cable near a window or other suitable location.LAN portTo change settings, such as when setting up the product for thefirst time, connect your PC to this port using a LAN cable. Once theproduct is up and running, you may disconnect the LAN cable. Ifyour PC does not support Wi-Fi, you can leave it connected.WAN portConnect one end of a LAN cable to this port and the other end tothe LAN port on your router, modem, or other device used toconnect to the Internet.Power portConnect the supplied AC adapter to this connector. The productdoes not include a Power or On/Off button. Connecting the powercable automatically turns on the product.Reset buttonThe Reset button is recessed on the back of the product and isused to reset or restart the product:• To reset (reinitialize) the product to factory-default settings,press and hold the Reset button for 10 seconds. Caution: Yoursettings will be lost! For more information, refer to Reset theProduct.• To restart the product without losing your settings, just pressthe Reset button. The product will restart.User GuidePorts and Reset ButtonPage 12BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
7LEDsAttention: Once the product has beenpowered up and configured, all LEDsshould be a steady (not blinking) green.If any LED is not steady green, refer to Troubleshooting.ACTIVE LED Off — Power off or product failureSteady Green — Activation complete/normal operationBlinking Green — Activation in progressSteady Orange — Product alarmBlinking Orange — Product alarm during activationWAN LED Off — Power off or WAN link (Ethernet connection) downSteady Green — Internet connection normal Fast Blinking Green — Files downloadingSlow Blinking Green — NTP access errorSteady Orange — Link errorFast Blinking Orange — Link error while downloading filesSlow Blinking Orange — Link error (NTP access error)LTE LED Off — Power off or LTE signal offSteady Green — LTE signal on/normal operationFast Blinking Green — RF validation in progressSlow Blinking Green — NTP calibration error duringsynchronizationFast Blinking Orange — Temperature alarmGPS LED Off — Power off or hardware problemSteady Green — GPS measurement completed/normaloperationFast Blinking Green — GPS measurement incomplete or inprogressUser GuideLEDsPage 13BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
8Before You BeginImportant!To avoid personal injury or damage to the equipment, carefully read and adhere to the Important Precautions.If you encounter problems while installing or operating this product, refer to Troubleshooting.System Requirements• Internet connection via a router or broadband modem• An available LAN (Ethernet) portRequired MaterialIn addition to the items included in the box, you should have the following items before installing and setting upthe product:• PC or laptop running Mac or Windows operating system• One LAN cable for connecting the product to a LAN port (Internet connection)• One spare LAN cable for temporarily connecting your PC to the product for the initial setup• Optional: Surge/spike protector or UPS• Optional: Two screws of appropriate type (that is, wood, drywall, or concrete) and size if mounting the producton a wall• Optional: Network subscription document (For the Internet connection, network subscription is required.)User GuideBefore You BeginPage 14BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
9Installation and SetupIn this chapter:9.1 Physically Mount the Product9.2 Connect the Product to a LAN Port9.3 Connect the GPS Antenna9.4 Connect the AC Adapter9.5 Perform Initial SetupUser GuideInstallation and SetupPage 15BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
9.1Physically Mount the ProductIn this section:9.1.1 Mount the Product on a Flat Surface9.1.2 Mount the Product on a Wall+Important: For stability, the product should always be mounted using the supplied stand. Whenchoosing a location, ensure that all necessary wired connections, including the power supply, can beplugged into the product.9.1.1Mount the Product on a Flat SurfaceTo mount the product on a flat surface:Step 1Place the stand on a flat surface. If desired, the stand can be attached to the surface using two screws(not included).Step 2Align the mounting slots on the bottom of the product with the corresponding slots on the top of thestand. User GuideInstallation and SetupPhysically Mount the ProductPage 16BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Step 3Slowly slide the product onto the stand until you feel it click into place.9.1.2Mount the Product on a WallTo mount the product on a wall:Step 1Attach the stand to the wall using the appropriate mounting hardware (not supplied), ensuring thatthe arrow on the stand base is pointing straight up (see photo below) and that the stand is level:• If attaching directly to a wooden or plywood wall, use two #6 x 1 in. wood screws. If attaching towall studs, use two #6 x 1-1/2 in. or #6 x 2 in. wood screws instead.• If attaching to drywall, use two #6 screws and drywall anchors capable of supporting 12 lbs or more.Screws and anchors can be bought as a set (for example, E-Z Ancor® Twist-N-Lock™ drywall anchorsand screws) from any home-improvement store.• If attaching to concrete, ensure that appropriate screws and anchors are used.Step 2Aligning the slots on the back of the product with the corresponding hooks on the stand, slide theproduct onto the stand, and push down firmly.Warning: Do not let go of the product until you are absolutely sure that it is securely fastened.User GuideInstallation and SetupPhysically Mount the ProductPage 17BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Step 3Gently pull on the product to ensure that it is securely fastened.User GuideInstallation and SetupPhysically Mount the ProductPage 18BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
9.2Connect the Product to a LAN PortUsing a LAN cable, connect the WAN port on the product to the LAN port used for your Internet connection. If yourPC is currently connected to the LAN port, simply disconnect the cable from your PC and reconnect it to the WANport on the product. When finished, the product should be connected as illustrated in one of the scenariosillustrated below:Connect tothe LAN port.LAN CableConnect to the WANport of the product.Modem/Router/ONUInternetConnectionLAN WANs6001dd_1Figure 1: Internet Connection through Modem, Wireless Router, or ONUInternetConnectionModem/Router/ONU Wired RouterLAN CableConnect tothe LAN port.Connect to the WANport of the product.LAN WANs6001de_1Figure 2: Internet Connection through Wired RouterUser GuideInstallation and SetupConnect the Product to a LAN PortPage 19BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
LAN CableInternetConnection Connect tothe LAN port.Connect to the WANport of the product.LAN WANs6001df_1Figure 3: Internet Connection through LAN Port Directly Installed in WallUser GuideInstallation and SetupConnect the Product to a LAN PortPage 20BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
9.3Connect the GPS AntennaGPS is essential for location-based services, such as E911 emergency services. Unfortunately, GPS reception canbe weak or nonexistent in some locations, especially indoors, where the building structure may interfere with GPSreception. Because of this, the included GPS antenna must be connected to the product and located in the sameroom or area as the product.Connect the GPS antenna to the GPS port on the product, and then place the receiving end of the GPS antenna asclose as possible to an outside window or doorway. When placing the receiving end of the GPS antenna, be awarethat it must be in the same room or area as the product.User GuideInstallation and SetupConnect the GPS AntennaPage 21BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
9.4Connect the AC AdapterThe product does not have a power button. To turn on the product, connect the supplied AC adapter to theproduct and a power outlet as shown below. Plugging the AC adapter into a surge/spike protector or UPS(uninterruptible power supply) is recommended.Before doing so, please observe the following precautions to avoid damage to the product or AC adapter:• Use only the supplied AC adapter. Do not use an AC adapter from another product.• Do not bend or kink the AC adapter cord, and do not pull on the cord.• Do not bundle the AC adapter cord with the LAN cable.• Do not place heavy objects on the AC adapter or cord.• To avoid accidentally damaging the cord, plug the AC adapter power plug into an outlet near the product tokeep the amount of exposed cord to a minimum, and ensure that the exposed cord is always visible.The product initializes automatically when powered on. Initialization takes approximately 3 minutes. Wheninitialization is complete, proceed to the next step to perform initial setup.User GuideInstallation and SetupConnect the AC AdapterPage 22BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
9.5Perform Initial SetupStep 1Connect LAN cable from your PC (desktop or laptop) to the LAN port of the product.Step 2Open a Web browser, and enter http://192.168.5.1 in the address bar.The Login page opens.Step 3Enter Fujitsu-HeNB in the User Name field, and then click Login. Leave the Password field blank.The home page opens. From the home page, you can configure or change settings by clicking theSetting button, view current settings by clicking the System Information button, and add or changethe password by clicking the Fujitsu-HeNB button at the top of the page. From any other page, clickTOP to return to this page.User GuideInstallation and SetupPerform Initial SetupPage 23BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Step 4To configure settings, click Setting.The Settings page opens. The specific fields shown on the Settings page depend on the connection typeselected. By default, the DHCP connection type is selected. Presently, only the DHCP and Static IPAddress connection types are supported. The PPPoE connection type is not supported.User GuideInstallation and SetupPerform Initial SetupPage 24BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Figure 4: DHCP Connection TypeFigure 5: Static IP Address Connection TypeStep 5Fill in all fields as required using the information provided by your service provider at the time ofpurchase. Required fields are indicated with a red asterisk (*).User GuideInstallation and SetupPerform Initial SetupPage 25BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Hint: While making changes, if at any time you want to reset all fields to their default values, clickInit. To save those values, click Apply.Step 6When finished, click Apply.The product restarts to apply the new settings.Step 7Wait for the product to restart.After the product turns on, it will take a few minutes for the ACTIVE LED to turn green after the productturns on. If the ACTIVE LED turns green, the initial setup is complete, and the product is connected tothe 4G LTE network.If the ACTIVE LED does not turn green after several minutes, perform the following steps:a) Unplug the AC adapter from the product, reconnect the AC adapter, and wait a few minutes.b) Turn off the modem/router/ONU, wait for approximately 30 minutes, and then check again.c) If the ACTIVE LED still does not turn green, contact customer service.Step 8Confirm that your smartphone or tablet is registered to the product.Note: The procedure for confirming registration varies by device and service provider. Please consult yourdevice's user manual.Step 9Confirm the Internet Connection by opening a Web browser on your smartphone or tablet and going toany Web address.User GuideInstallation and SetupPerform Initial SetupPage 26BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
10Reset the ProductIf a status lamp indicates a failure, the product may need to be reset. Resetting rebuilds the product'sconnection to the network. Following a reset, most settings configured during initial setup, such asyour user name and password, are retained.+Important: This task is normally performed by the service provider or under the direction of theservice provider. If you arrived at this task on your own, contact your service provider beforeproceeding.To reset the product:Step 1Ensure that the power is on.Step 2Using a sharp-pointed object, such as a toothpick or pen, press and hold the Reset button for 10seconds or longer, and then release the button.Step 3Make sure that the product restarts.User GuideReset the ProductPage 27BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
Step 4Go to Perform Initial Setup to perform initial setup again.User GuideReset the ProductPage 28BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
11TroubleshootingIf you are experiencing problems, start by observing the LEDs on the front of the product. Once the product hasbeen powered up and configured, all LEDs should be a steady green, which indicates normal operation. If anyLEDs are not a steady green, proceed as follows:Hint: If more than one LED indicates a problem, address them one at a time since a single problemmay affect multiple LEDs.ACTIVE LED is OffPower is not reaching the product, or the product has failed and will not turn on. If the product will not turn on,ensure that the AC adapter is properly connected and that the power outlet has power. If the product still will notturn on, contact customer service for repair or replacement.ACTIVE LED is Blinking GreenThis is not a problem. A blinking-green LED indicates that activation is in progress. Wait a few minutes for theactivation to complete. Once activation is complete, the ACTIVE LED should turn a steady green.ACTIVE LED is Steady or Blinking OrangeThe product is experiencing a general failure. If the ACTIVE LED is blinking orange, wait a few minutes to see if theproblem resolves on its own. If the problem persists, continue with the next step. If the ACTIVE LED is a steadyorange or continues blinking orange, initialize the product as described in Reset the Product. If initializing theproduct does not work, contact customer service for repair or replacement.WAN LED is OffPower is not reaching the product, or there is no Ethernet connection.First verify that the product is receiving power. If that is not the problem, check your Ethernet connection byconnecting another device and trying to reach the Internet. If the Ethernet connection is working, the productmay be defective. Contact customer service.Be aware that some communication devices, such as certain cable TV set-top boxes, save the last Internet-connection settings in memory, so you may not be able to reconnect to the Internet. To erase these settings,User GuideTroubleshootingPage 29BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
power down the device by removing the AC adapter, and wait for approximately 30 minutes before reconnectingthe AC adapter. This will allow the device to adopt new settings.WAN LED is Fast Blinking GreenFiles are downloading. This is normal. The LED should change to a steady green momentarily.WAN LED is Slow Blinking GreenAn NTP access error has occurred. If the problem does not resolve itself in a few minutes, contact customersupport.WAN LED is Steady OrangeA link error has occurred in the network. Contact customer support.WAN LED is Fast Blinking OrangeA link error occurred while downloading files. If the problem does not resolve itself in a few minutes, contactcustomer support.WAN LED is Slow Blinking OrangeA link error (NTP access error) has occurred in the network. If the problem does not resolve itself in a few minutes,contact customer support.LTE LED is OffPower is off, or the LTE signal is off. Verify that the product is receiving power. If the product is receiving power,verify that all cables and securely connected to the appropriate ports. If the LTE LED remains off, contact customersupport.LTE LED is Fast Blinking GreenRadio frequency (RF) validation is in progress. When complete, the LTE LED should turn steady green, indicatingnormal operation.LTE LED is Slow Blinking GreenNTP calibration error during synchronizationLTE LED is Fast Blinking OrangeTemperature alarmUser GuideTroubleshootingPage 30BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
GPS LED is OffPower is off, or there is a hardware problem. Verify that the product is receiving power. If the product is receivingpower and the GPS LED remains dark, the product is defective. Contact customer support for a replacement.GPS LED is Fast Blinking GreenGPS measurement is incomplete or in progress. Wait a few minutes. If the LED does not change to a steady green,try repositioning the GPS cable to get better GPS reception. After a few minutes, if the LED does not change to asteady green, contact customer support.User GuideTroubleshootingPage 31BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
12SpecificationsWeight Less than 1.3 lbs (0.6 kg), excluding bracketDimensions (H x W x D) 9.0 in. x 5.9 in. x 1.2 in. (230 mm x 150 mm x 30 mm)Temperature Operating (up to 1800 m): 32 to 104 °F (0 to 40 °C)Short-term: 23 to 122 °F (–5 to 50 °C)Operating Humidity 5 to 95%Electrical Safety UL-60950-1FCC Radiation Emission FCC Part 15 Subpart BUser GuideSpecificationsPage 32BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
13Radio Frequency EnergyWhen operating, your LS110 Residential Femtocell transmits and receives radio frequency (RF) signals, and yournetwork provider controls the power level of the signals being transmitted and received. The power level can beas high as 100 milliwatts.User GuideRadio Frequency EnergyPage 33BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
14FCC Radio Frequency EmissionThis device meets the FCC Radio Frequency Emission Guidelines. FCC ID number: A3LSCS-2U01.FCC StatementThis product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and used according to the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which is found by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) This device must accept any interference received, includinginterference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate this equipment.FCC Radiation Exposure StatementTo ensure the safety of users, the FCC has established criteria for the amount of radio frequency energy variousproducts may produce depending on their intended usage. This product has been tested and found to complywith the FCC’s exposure criteria.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.User GuideFCC Radio Frequency EmissionPage 34BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
The installation of the base unit should allow at least 20 centimeters between the base and persons to be incompliance with FCC RF exposure guidelines.User GuideFCC Radio Frequency EmissionPage 35BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
15Limited WarrantyFujitsu warrants the LS110 Residential Femtocell against defects in materials and workmanship under normal usefor 1 year from the date of purchase.User GuideLimited WarrantyPage 36BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
16End-User License AgreementThis product:• Apache License Version 2.0• Apache Software Foundation [Ni]• Axis2 Project [No] Software | Axis2/C=============================================================================Apache LicenseVersion 2.0, January 2004http://www.apache.org/licenses/TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION1. Definitions:"License" shall mean the terms and conditions for use, reproduction, and distribution as defined bySections 1 through 9 of this document."Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is grantingthe License."Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlledby, or are under common control with that entity. For the purposes of this definition, "control" means (i)the power, direct or indirect, to cause the direction or management of such entity, whether by contractor otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficialownership of such entity."You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License."Source" form shall mean the preferred form for making modifications, including but not limited tosoftware source code, documentation source, and configuration files.User GuideEnd-User License AgreementPage 37BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
"Object" form shall mean any form resulting from mechanical transformation or translation of a Sourceform, including but not limited to compiled object code, generated documentation, and conversions toother media types."Work" shall mean the work of authorship, whether in Source or Object form, made available under theLicense, as indicated by a copyright notice that is included in or attached to the work (an example isprovided in the Appendix below)."Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derivedfrom) the Work and for which the editorial revisions, annotations, elaborations, or other modificationsrepresent, as a whole, an original work of authorship. For the purposes of this License, Derivative Worksshall not include works that remain separable from, or merely link (or bind by name) to the interfacesof, the Work and Derivative Works thereof."Contribution" shall mean any work of authorship, including the original version of the Work and anymodifications or additions to that Work or Derivative Works thereof, that is intentionally submitted toLicensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorizedto submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means anyform of electronic, verbal, or written communication sent to the Licensor or its representatives, includingbut not limited to communication on electronic mailing lists, source code control systems, and issuetracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing andimproving the Work, but excluding communication that is conspicuously marked or otherwisedesignated in writing by the copyright owner as "Not a Contribution.""Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contributionhas been received by Licensor and subsequently incorporated within the Work.2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor herebygrants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright licenseto reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute theWork and such Derivative Works in Source or Object form.3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grantsto You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in thissection) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work,where such license applies only to those patent claims licensable by such Contributor that are necessarilyinfringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to whichsuch Contribution(s) was submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Workconstitutes direct or contributory patent infringement, then any patent licenses granted to You under thisLicense for that Work shall terminate as of the date such litigation is filed.4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in anymedium, with or without modifications, and in Source or Object form, provided that You meet the followingconditions:(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and(b) You must cause any modified files to carry prominent notices stating that You changed the files; andUser GuideEnd-User License AgreementPage 38BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent,trademark, and attribution notices from the Source form of the Work, excluding those notices that donot pertain to any part of the Derivative Works; and(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative 11 Works thatYou distribute must include a readable copy of the attribution notices contained within such NOTICE file,excluding those notices that do not pertain to any part of the Derivative Works, in at least one of thefollowing places: within a NOTICE text file distributed as part of the Derivative Works; within the Sourceform or documentation, if provided along with the Derivative Works; or, within a display generated bythe Derivative Works, if and wherever such third-party notices normally appear. The contents of theNOTICE file are for informational purposes only and do not modify the License. You may add Your ownattribution notices within Derivative Works that You distribute, alongside or as an addendum to theNOTICE text from the Work, provided that such additional attribution notices cannot be construed asmodifying the License. You may add Your own copyright statement to Your modifications and mayprovide additional or different license terms and conditions for use, reproduction, or distribution of Yourmodifications, or for any such Derivative Works as a whole, provided Your use, reproduction, anddistribution of the Work otherwise complies with the conditions stated in this License.5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submittedfor inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License,without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede ormodify the terms of any separate license agreement you may have executed with Licensor regarding suchContributions.6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, orproduct names of the Licensor, except as required for reasonable and customary use in describing the originof the Work and reproducing the content of the NOTICE file.7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides theWork (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES ORCONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties orconditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. Youare solely responsible for determining the appropriateness of using or redistributing the Work and assumeany risks associated with Your exercise of permissions under this License.8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence),contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts) oragreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect,special, incidental, or consequential damages of any character arising as a result of this License or out ofthe use or inability to use the Work (including but not limited to damages for loss of goodwill, workstoppage, computer failure or malfunction, or any and all other commercial damages or losses), even ifsuch Contributor has been advised of the possibility of such damages.9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, Youmay choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liabilityobligations and/or rights consistent with this License. However, in 12 accepting such obligations, You mayact only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, andonly if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, orclaims asserted against, such Contributor by reason of your accepting any such warranty or additionalliability.User GuideEnd-User License AgreementPage 39BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
APPENDIX: How to apply the Apache License to your workTo apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed bybrackets "[]" replaced with your own identifying information. (Don't include the brackets!) The text should beenclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name anddescription of purpose be included on the same "printed page" as the copyright notice for easier identificationwithin third-party archives.Copyright [yyyy] [name of copyright owner]Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliancewith the License. You may obtain a copy of the License athttp://www.apache.org/licenses/LICENSE-2.0Unless required by applicable law or agreed to in writing, software distributed under the License is distributed onan "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the Licensefor the specific language governing permissions and limitations under the License.=============================================================================User GuideEnd-User License AgreementPage 40BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
17Open Source SoftwareIn this chapter:17.1 Guide to Micro Base Station Open Source Software17.2 Open Source Software LicensingUser GuideOpen Source SoftwarePage 41BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
17.1Guide to Micro Base Station Open Source SoftwareAbout Open Source SoftwareThe following open source software (hereafter, it is said "OSS") is mounted to this device. Please confirm followingURL content about the method of obtaining the source code based on each use permission conditioncorresponding to the use permission condition and each OSS applied to each OSS.URL: https://jp.fujitsu.com/telecom/carrier/download/broadone-ls102/userID: DLOssNetwork password:The condition applied to OssSoft312BE for each OSS is as follows:1. Use permission condition name:Apache License Version 2.0OSS name: Axis2c2. Use permission condition name:BSD LicenseOSS name: db4,fcgi,flex,libcap,libpcap,libupnp,lighttpd,mktemp,mrouted,nfs-utilslib,openssh,portmap,shadow-utils,tcpdump,tftp-hpa,uspdcp3. Use permission condition name:BSD License and GNU Lesser General Public License version 2.1 and GNU General Public License version2 and Public DomainOSS name: Ppp4. Use permission condition name:GNU General Public License version 2OSS name: attr,bash,bridge-utils,busybox,e2fsprogs,ebtables,ethtool,iptables,Linux_driver,linuxigd,lzo,nfs-utils,pciutils,perl,proftpd,readline,rfutil,rp-pppoe,sed,strongswan,tcp_wrappers,U-boot,udev,wireless-tools5. Use permission condition name:GNU General Public License version 2+OSS name: Libgcc and libstdcxxUser GuideOpen Source SoftwareGuide to Micro Base Station Open Source SoftwarePage 42BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
6. Use permission condition name:GNU General Public License version 2 and BSD License and Public DomainOSS name: Util-linux-ng7. Use permission condition name:GNU General Public License version 2 and GNU Lesser General Public License version 2.1OSS name: Acl, glibc, and gmp8. Use permission condition name:GNU General Public License version 2 and GNU Lesser General Public License version 2.1 and MIT LicenseOSS name: Lksctp-tools9. Use permission condition name:GNU General Public License version 2 and Public DomainOSS name: Iproute10. Use permission condition name:GNU Lesser General Public License version 2.1OSS name: Libblkid, nss-mdns, and procps11. Use permission condition name:GNU Lesser General Public LicenseOSS name: Ipc12. Use permission condition name:Internet Systems ConsortiumOSS name: Dhcp and bind13. Use permission condition name:MIT LicenseOSS name: Curl, dropbear, libxml2, ncurses, and popt14. Use permission condition name:OpenSSL LicenseUser GuideOpen Source SoftwareGuide to Micro Base Station Open Source SoftwarePage 43BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
OSS name: Openssl15. Use permission condition name:Public DomainOSS name: Basesystem, filesystem, setup, and sqlite16. Use permission condition name:Xinetd LicenseOSS name: Xinetd17. Use permission condition name:Zlib licenseOSS name: ZlibAbout the Program that Permits Remodeling and Reverse EngineeringThe following programs included in this software are assumed to be the one that only the range permitted byGNU LESSER GENERAL PUBLIC LICENSE Version 2.1 can do the rearrangement and the reverse engineering.File name:procps-3.2.8libblkid-2.16nss-mdns-0.8User GuideOpen Source SoftwareGuide to Micro Base Station Open Source SoftwarePage 44BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
17.2Open Source Software LicensingThis product:• u-boot-2011.06• GNU GENERAL PUBLIC LICENSE Version 2 (GPL-2)=============================================================================GNU GENERAL PUBLIC LICENSEVersion 2, June 1991Copyright (C) 1989, 1991 Free Software Foundation, Inc.59 Temple Place, Suite 330, Boston, MA 02111-1307 USAEveryone is permitted to copy and distribute verbatim copies of this license document, but changing it is notallowed.PreambleThe licenses for most software are designed to take away your freedom to share and change it. By contrast, theGNU General Public License is intended to guarantee your freedom to share and change free software--to makesure the software is free for all its users. This General Public License applies to most of the Free SoftwareFoundation's software and to any other program whose authors commit to using it. (Some other Free SoftwareFoundation software is covered by the GNU Library General Public License instead.) You can apply it to yourprograms, too.When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designedto make sure that you have the freedom to distribute copies of free software (and charge for this service if youwish), that you receive source code or can get it if you want it, that you can change the software or use pieces ofit in new free programs; and that you know you can do these things.To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you tosurrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of thesoftware, or if you modify it.For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipientsall the rights that you have. You must make sure that they, too, receive or can get the source code. And you mustshow them these terms so they know their rights.We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives youlegal permission to copy, distribute and/or modify the software.Also, for each author's protection and ours, we want to make certain that everyone understands that there is nowarranty for this free software. If the software is modified by someone else and passed on, we want its recipientsUser GuideOpen Source SoftwareOpen Source Software LicensingPage 45BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
to know that what they have is not the original, so that any problems introduced by others will not reflect on theoriginal authors' reputations.Finally, any free program is threatened constantly by software patents. We wish to avoid the danger thatredistributors of a free program will individually obtain patent licenses, in effect making the program proprietary.To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed atall.The precise terms and conditions for copying, distribution and modification follow.GNU GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION1. This License applies to any program or other work which contains a notice placed by the copyright holdersaying it may be distributed under the terms of this General Public License. The "Program", below, refers toany such program or work, and a "work based on the Program" means either the Program or any derivativework under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim orwith modifications and/or translated into another language. (Hereinafter, translation is included withoutlimitation in the term "modification".) Each licensee is addressed as "you".Activities other than copying, distribution and modification are not covered by this License; they are outsideits scope. The act of running the Program is not restricted, and the output from the Program is covered onlyif its contents constitute a work based on the Program (independent of having been made by running theProgram). Whether that is true depends on what the Program does.2. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium,provided that you conspicuously and appropriately publish on each copy an appropriate copyright noticeand disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of anywarranty; and give any other recipients of the Program a copy of this License along with the Program.You may charge a fee for the physical act of transferring a copy, and you may at your option offer warrantyprotection in exchange for a fee.3. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on theProgram, and copy and distribute such modifications or work under the terms of Section 1 above, providedthat you also meet all of these conditions:a) You must cause the modified files to carry prominent notices stating that you changed the files andthe date of any change.b) You must cause any work that you distribute or publish, that in whole or in part contains or is derivedfrom the Program or any part thereof, to be licensed as a whole at no charge to all third parties underthe terms of this License.c) If the modified program normally reads commands interactively when run, you must cause it, whenstarted running for such interactive use in the most ordinary way, to print or display an announcementincluding an appropriate copyright notice and a notice that there is no warranty (or else, saying that youprovide a warranty) and that users may redistribute the program under these conditions, and telling theuser how to view a copy of this License. (Exception: if the Program itself is interactive but does notnormally print such an announcement, your work based on the Program is not required to print anannouncement.)User GuideOpen Source SoftwareOpen Source Software LicensingPage 46BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
These requirements apply to the modified work as a whole. If identifiable sections of that work are notderived from the Program, and can be reasonably considered independent and separate works inthemselves, then this License, and its terms, do not apply to those sections when you distribute them asseparate works. But when you distribute the same sections as part of a whole which is a work based on theProgram, the distribution of the whole must be on the terms of this License, whose permissions for otherlicensees extend to the entire whole, and thus to each and every part regardless of who wrote it.Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you;rather, the intent is to exercise the right to control the distribution of derivative or collective works based onthe Program.In addition, mere aggregation of another work not based on the Program with the Program (or with a workbased on the Program) on a volume of a storage or distribution medium does not bring the other workunder the scope of this License.4. You may copy and distribute the Program (or a work based on it, under Section 2) in object code orexecutable form under the terms of Sections 1 and 2 above provided that you also do one of the following:a) Accompany it with the complete corresponding machine-readable source code, which must bedistributed under the terms of Sections 1 and 2 above on a medium customarily used for softwareinterchange; or,b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge nomore than your cost of physically performing source distribution, a complete machine-readable copy ofthe corresponding source code, to be distributed under the terms of Sections 1 and 2 above on amedium customarily used for software interchange; or,c) Accompany it with the information you received as to the offer to distribute corresponding sourcecode. (This alternative is allowed only for noncommercial distribution and only if you received theprogram in object code or executable form with such an offer, in accord with Subsection b above.)The source code for a work means the preferred form of the work for making modifications to it. For anexecutable work, complete source code means all the source code for all modules it contains, plus anyassociated interface definition files, plus the scripts used to control compilation and installation of theexecutable. However, as a special exception, the source code distributed need not include anything that isnormally distributed (in either source or binary form) with the major components (compiler, kernel, and soon) of the operating system on which the executable runs, unless that component itself accompanies theexecutable. If distribution of executable or object code is made by offering access to copy from a designatedplace, then offering equivalent access to copy the source code from the same place counts as distribution ofthe source code, even though third parties are not compelled to copy the source along with the object code.5. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under thisLicense. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and willautomatically terminate your rights under this License. However, parties who have received copies, orrights, from you under this License will not have their licenses terminated so long as such parties remain infull compliance.6. You are not required to accept this License, since you have not signed it. However, nothing else grants youpermission to modify or distribute the Program or its derivative works. These actions are prohibited by law ifyou do not accept this License. Therefore, by modifying or distributing the Program (or any work based onUser GuideOpen Source SoftwareOpen Source Software LicensingPage 47BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
the Program), you indicate your acceptance of this License to do so, and all its terms and conditions forcopying, distributing or modifying the Program or works based on it.7. Each time you redistribute the Program (or any work based on the Program), the recipient automaticallyreceives a license from the original licensor to copy, distribute or modify the Program subject to these termsand conditions. You may not impose any further restrictions on the recipients' exercise of the rights grantedherein. You are not responsible for enforcing compliance by third parties to this License.8. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (notlimited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise)that contradict the conditions of this License, they do not excuse you from the conditions of this License. Ifyou cannot distribute so as to satisfy simultaneously your obligations under this License and any otherpertinent obligations, then as a consequence you may not distribute the Program at all. For example, if apatent license would not permit royalty-free redistribution of the Program by all those who receive copiesdirectly or indirectly through you, then the only way you could satisfy both it and this License would be torefrain entirely from distribution of the Program.If any portion of this section is held invalid or unenforceable under any particular circumstance, the balanceof the section is intended to apply and the section as a whole is intended to apply in other circumstances.It is not the purpose of this section to induce you to infringe any patents or other property right claims or tocontest validity of any such claims; this section has the sole purpose of protecting the integrity of the freesoftware distribution system, which is implemented by public license practices. Many people have madegenerous contributions to the wide range of software distributed through that system in reliance onconsistent application of that system; it is up to the author/donor to decide if he or she is willing todistribute software through any other system and a licensee cannot impose that choice.This section is intended to make thoroughly clear what is believed to be a consequence of the rest of thisLicense.9. If the distribution and/or use of the Program is restricted in certain countries either by patents or bycopyrighted interfaces, the original copyright holder who places the Program under this License may add anexplicit geographical distribution limitation excluding those countries, so that distribution is permitted onlyin or among countries not thus excluded. In such case, this License incorporates the limitation as if writtenin the body of this License.10. The Free Software Foundation may publish revised and/or new versions of the General Public License fromtime to time. Such new versions will be similar in spirit to the present version, but may differ in detail toaddress new problems or concerns.Each version is given a distinguishing version number. If the Program specifies a version number of thisLicense which applies to it and "any later version", you have the option of following the terms andconditions either of that version or of any later version published by the Free Software Foundation. If theProgram does not specify a version number of this License, you may choose any version ever published bythe Free Software Foundation.11. If you wish to incorporate parts of the Program into other free programs whose distribution conditions aredifferent, write to the author to ask for permission. For software which is copyrighted by the Free SoftwareFoundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decisionwill be guided by the two goals of preserving the free status of all derivatives of our free software and ofpromoting the sharing and reuse of software generally.User GuideOpen Source SoftwareOpen Source Software LicensingPage 48BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only
NO WARRANTYBECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THEEXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHTHOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THEPROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARYSERVICING, REPAIR OR CORRECTION.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BELIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGESARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATAOR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY 8 YOU OR THIRD PARTIES OR A FAILURE OFTHE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.END OF TERMS AND CONDITIONS=============================================================================User GuideOpen Source SoftwareOpen Source Software LicensingPage 49BroadOne LS110 ResidentialFemtocellRelease 14 Issue 1, May 2015FNC-LS110-0014-100Fujitsu and Fujitsu Customer Use Only

Navigation menu