Fujitsu Technology Solutions SCENIC6201 User Manual A26361 K520 Z100 1 7619

Fujitsu Technology Solutions GmbH A26361 K520 Z100 1 7619

SCENIC 600 Operating Manual January 1999 Edition

A26361-K520-Z100-1-7619 1IntroductionThis Operating Manual tells you how to put your PC into operation and how to operate it in daily use.This description applies for all configuration levels. Depending on the configuration level chosensome of the hardware components described may not be available on your PC. Please observe thenotes on your operating system.Your device is a powerful PC which is suitable for both professional and private use.Your PC is available in various configuration levels, which differ in hardware and softwareequipment. In addition, you can incorporate operable drives (for example DAT drive, streamer) anda second hard disk, as well as other boards.Depending on the configuration level chosen, your PC is supplied with Windows 9x or Windows NTas the operating system.Your PC has a number of security features to ensure that no unauthorized persons can access yourdata. For example, you can activate a screen saver with password protection. The security functionsin the BIOS Setup also allow you to protect your data by means of passwords. In addition, you canalso lock your PC mechanically using the cover lock. Systems with a chipcard reader offer additionalprotection.Further information on this PC is provided:• in the manual "Safety, Guarantee and Ergonomics"• in the Operating Manual for the monitor• in the Technical Manual for the system board• in the manual "BIOS Setup"• in the documentation of your operating system• in the information files (e. g. *.TXT, *.DOC, *.WRI, *.HLP)iSome of the manuals listed can be found on the CD "Drivers & Utilities" providedwith your computer. These manuals can be read and printed with theAcrobat Reader contained on the CD.Notational conventionsThe meanings of the symbols and fonts used in this manual are as follows:!Pay particular attention to texts marked with this symbol. Failure to observe this warningendangers your life, destroys the system, or may lead to loss of data.iThis symbol is followed by supplementary information, remarks and tips.Texts which follow this symbol describe activities that must be performed in the order shown.Texts in this typeface are screen outputs.Texts in italics indicate commands or menu items."Quotation marks" indicate names of chapters and terms that are being emphasized.
A26361-K520-Z100-1-7619 3Important notesIn this chapter you will find information regarding safety which it is essential to take note of whenworking with your PC. The manufacturer's notes contain helpful information on your PC.Safety!Pay attention to the information provided in the manual "Safety, Guarantee andErgonomics" and to the following notes.• During installation and before operating the device, observe the instructions on environmentalconditions in the chapter entitled "Technical data" as well as the instructions in the chapter"Preparation for use and operation".• Please check whether the device is set to the local power supply (see chapter "Preparation foruse and operation").• The main switch and the ON/OFF switch do not disconnect the system unit from the linevoltage. To disconnect the line voltage completely, remove the power plug from the groundedpower outlet.• Replace the lithium battery on the system board in accordance with the instructions in thechapter "System expansions - Replacing processor and lithium battery".• Caution: components in the system can get very hot.• Keep this Operating Manual together with your device. If you pass on the device to thirdparties, you should also pass on this manual.Notes on installing and removing boardsBoards with electrostatic sensitive devices (ESD) may be identified by thelabel shown.When you handle boards fitted with ESDs, you must observe the followingpoints under all circumstances:• You must always discharge yourself (e.g. by touching a groundedobject) before working.• The equipment and tools you use must be free of static charges.• Pull out the power plug before inserting or pulling out boards containingESDs.• Always hold boards with ESDs by their edges.• Never touch pins or conductors on boards fitted with ESDs.
Important notes Manufacturer's notes4A26361-K520-Z100-1-7619Manufacturer's notesEnergy savingWhen the PC is delivered, some energy-saving functions are already set (see the Technical Manualfor the system board or the manual "BIOS Setup").• If you are not using your PC, switch it off.• In the BIOS Setup you may set further energy-saving functions for the PC (see the TechnicalManual of the system board or in the manual "BIOS Setup").Energy saving under Windows NTIf the attached monitor and screen controller support power management in accordance with VESA(DPMS), the screen saver Powersaver ("Drivers & Utilities" CD) can be used to switch the monitorinto power management mode.Energy saving under Windows 95The Screen Saver tab allows you to set further energy-saving functions for your screen. Select thefollowing item in the Start menu: Settings - Control Panel - Display - Display Properties - Screen Saver -Energy saving features of monitor.Energy saving under Windows 98In the Start - Settings - Control Panel - Power Management menu you can set additional power-management functions.Disposal and recyclingThis device has been manufactured to the greatest possible degree from materials which can berecycled or disposed of in a manner that is not environmentally damaging. The device is taken backafter use, so that it can be recycled, provided that it is returned in a condition which is the result ofnormal use. Any components not recuperated will be disposed of in an environmentally acceptablemanner.For devices marked with this symbol Siemens AG offers a guarantee for36 months with a Bring-in-Service. The guarantee starts on the day ofdelivery (sale date) by Siemens or a Siemens partner.We herewith declare that it will be possible to repair any device marked withthe eco-label for at least 5 years after production of that device hasdiscontinued.Information on power management and energy saving mode can be found inchapter "Technical data".Do not throw lithium batteries or accumulators into the trashcan. They must be disposed of inaccordance with local regulations concerning special waste.If you have any questions on disposal, please contact your local office, our service department, or,directly:Siemens AGRecyclingcenterD-33106 PaderbornTel.: 49 5251 818 010 / Fax: 49 5251 818 015
Power cord selection Important notesA26361-K520-Z100-1-7619 5CE certificateThe shipped version of this device complies with the requirements of the EEC directives89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage directive".FCC Class B Compliance StatementIf there is an FCC statement on the device, then:The following statement applies to the products covered in this manual, unless otherwise specifiedherein. The statement for other products will appear in the accompanying documentation.NOTE:This equipment has been tested and found to comply with the limits for a "Class B" digital device,pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-Causing Equipment Regulations. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in strict accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:• Reorient or relocate the receiving antenna.• Increase the separation between equipment and the receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.• Consult the dealer or an experienced radio/TV technician for help.Siemens AG is not responsible for any radio or television interference caused by unauthorizedmodifications of this equipment or the substitution or attachment of connecting cables andequipment other than those specified by Siemens AG. The correction of interferences caused bysuch unauthorized modification, substitution or attachment will be the responsibility of the user.The use of shielded I/O cables is required when connecting this equipment to any and all optionalperipheral or host devices. Failure to do so may violate FCC rules.Power cord selectionThe power cord for this unit has been packedseparately and has been selected accordingto the country of destination. It must be usedto prevent electric shock. Use the followingguidelines if it is necessary to replace theoriginal cord set.The female receptacle of the cord set mustmeet CEE-22 requirements (see Figure).
Important notes Power cord selection6A26361-K520-Z100-1-7619For the United States and CanadaUse a UL listed and CSA labeled cord set consisting of a three conductor cord with a maximumlength of 15 feet.For units which stand on a desk or table, type SVT or SJT cord sets shall be used.For units which stand on floor, only SJT type cord sets shall be used.The cord set must be selected according to the current rating for your unit. Please consult Table Afor the selection criteria for power cords used in the United States and Canada.Table A:Cord Type Size of Conductorsin Cord Maximum CurrentRating of UnitSJT 18 AWG16 AWG14 AWG10 Amps12 Amps12 AmpsSVT 18 AWG17 AWG 10 Amps12 AmpsFor units set at 115 V:use a parallel blade, grounding typeattachment plug rated 15 A, 125 V.For units set at 230 V (domestic use):use a tandem blade, grounding typeattachment plug rated 15 A, 250 V.For units set at 230 V (outside of the United States and Canada):use a cord set consisting of a minimum AWG according to Table A and a grounding type attachmentplug rated 15 A, 250 V. The cord set should have the appropriate safety approvals for the country inwhich the equipment will be installed and should be marked HAR.
Transporting the PC Important notesA26361-K520-Z100-1-7619 7For the United KingdomShould the plug on the flexible cord not be of the type for your socket outlets, do not use an adapterbut remove the plug from the cord and discard. Carefully prepare the end of the supply cord and fit asuitable plug.WARNINGTHIS APPLIANCE MUST BE EARTHEDIMPORTANTThe wires in this mains lead are coloured in accordance with the following code:Green and Yellow: EarthBlue: NeutralBrown: LiveAs the colours of the wires in the mains lead of this appliance may not correspond with the colouredmarkings identifying the terminals in your plug, proceed as follows:• The wire which is coloured Green and Yellow must be connected to the terminal in the plugwhich is marked with the letter E or by the earth symbol or coloured Green or Green andYellow.• The wire which is coloured Blue must be connected to the terminal which is marked with theletter N or coloured Black.• The wire which is coloured Brown must be connected to the terminal which is marked with theletter L or coloured Red.Transporting the PC!Transport all parts separately, and in their original packaging or in a packaging whichprotects them from knocks and jolts, to the new site. Do not unpack them until all transportmaneuvers are completed.Never drop the monitor (risk of implosion)!
Important notes Cleaning the PC8A26361-K520-Z100-1-7619Cleaning the PC!Turn off all power and equipment switches and pull the power plug out of the groundedpower outlets.Do not clean any interior parts yourself, leave this job to a service technician.Do not use any cleaning agents that contain abrasives or may corrode plastic.Ensure that no liquid enters the system.Ensure that the ventilation areas of the system unit and the monitor are free.Cleaning the system unit and the monitorWipe the system unit and monitor casing with a dry cloth. If particularly dirty, use a cloth which hasbeen moistened in mild domestic detergent and then carefully wrung out.Cleaning the keyboard and the mouseUse a cloth for disinfection to clean the keyboard and the mouse.Remove the retaining ring on the underside of the mouse and then clean the mouse mechanism andthe rotating ball.1234Using both thumbs exert downward pressure on the notches of the retaining ring and turn thering anticlockwise (1).Remove the retaining ring and the rotating ball from the mouse (2).Clean the three small wheels in the mouse and the ball with a lint-free cloth.Replace the ball and the retaining ring (3).Using both thumbs exert downward pressure on the notches of the retaining ring (4) and turnthe ring clockwise. You must feel the ring engage.
A26361-K520-Z100-1-7619 9Preparation for use and operation!Please take note of the safety information in the chapter "Important notes".Unpacking and checking the deliveryIt is recommended not to throw away the original packaging material! It may be required forreshipment at some later date.Unpack all the individual parts.Check the delivery for damage incurred during transport.Check whether the delivery agrees with the details in the delivery note.Should you discover that the delivery does not correspond to the delivery note, notify your localsales office immediately.iIf you have received drives or boards with your PC, please do not install them until afterfirst-time setup. How to install drives and boards is described in the chapter "Systemexpansions".Preparing the PC for useFirst-time setup includes the connection of the devices (monitor, mouse, keyboard etc.) and thesetup of the supplied software.When you set up the PC for the first time, you should carry out the following steps in the ordershown:1. Decide where you are going to use the PC.2. Connect the external devices to the system unit.3. Check the rated voltage of the system unit and connect it to the line voltage.4. Switch the PC on and follow the instructions on the screen.
Preparation for use and operation Setting up the PC10 A26361-K520-Z100-1-7619Setting up the PC!When installing your PC, give consideration to the recommendations and safety notes inthe manual "Safety, Guarantee and Ergonomics".Set up the PC only in its correct orientation. The points to observe are illustrated on thefollowing pages.We recommend that you place your equipment on a surface with good anti-slip qualities.In view of the multitude of different finishes and varnishes used on furniture, it is possiblethat the rubber feet of the devices will mark the surface they stand on.Do not expose the PC to extreme environmental conditions (see chapter "Technicaldata"). Protect it from dust, humidity and heat.Provide at least 200 mm of clearance on the left, in front of and behind the ventilator areaof the system unit to ensure adequate ventilation. Do not cover the ventilation areas of themonitor and the fan.Do not place several system units one above the other.Connecting devices!The power plug must be disconnected!Read the documentation on the external device before connecting it.Do not connect or disconnect cables during a thunderstorm.Always take hold of the actual plug body. Never unplug a cable by pulling the cable itself!Connect and disconnect the cables in the order described below.Connecting cables• Turn off all power and equipment switches.• Unplug all power plugs from the grounded power outlets.• Connect all cables at the system unit and peripherals. You must observe the informationprovided in the chapter "Important notes".• Plug all data communication cables into the utility sockets.• Plug all power cables into the grounded power outlets.Disconnecting cables• Turn off all power and equipment switches.• Unplug all power plugs from the grounded power outlets.• Unplug all data communication cables from the utility sockets.• Disconnect all cables from the system unit and peripherals.
Connecting devices Preparation for use and operationA26361-K520-Z100-1-7619 11Ports for external devicesThe ports for external devices are on the rear and on the front of the system unit. The portsavailable on your device depend on the configuration level you have selected. The standard portsare marked with symbols like those below or similar symbols. Exact details of the position of theports are supplied in the Technical Manuals for the boards.Keyboard port Serial port 1PS/2 mouse port Serial port 2Video connector Parallel interfaceUSB - Universal Serial Bus Game portLAN port Chipcard readerAudio output (Line out) Microphone jackAudio input (Line in)iSome of the devices that you connect require special drivers (see the documentation forthe connected device and for the operating system).
Preparation for use and operation Connecting devices12 A26361-K520-Z100-1-7619Connecting the keyboardiUse only the keyboard cable supplied.Plug the round plug of the keyboard cable into the keyboard port on the system unit.Plug the other connector of the keyboardcable into the socket on the underside ofthe keyboard.Connecting the mousePlug the connector of the mouse cable into the mouse port.iIf you do not attach a mouse at the PS/2 mouse port, you can disable the mousecontroller in the BIOS-Setup in order to free the IRQ12 for a different application.Connecting devices with serial or parallel portConnect the data cable to the external device.Connect the data cable of the external device to the appropriate port on the system unit.iMost devices that you connect to the serial or parallel port require special drivers. Youroperating system already includes many drivers . But if the driver you need is not on thehard disk please install it from the floppy disk supplied with the device or with theapplication program.If you need to change the default settings of the serial or parallel port (e.g. address,interrupt), you can do so in the BIOS Setup. The default setting for the interfaces aredescribed in the Technical Manual for the system board or in the "BIOS Setup" manual.
Connecting devices Preparation for use and operationA26361-K520-Z100-1-7619 13Connecting the monitor to the line voltagePrepare the monitor as described in the Operating Manual for the monitor.Plug the data cable of the monitor into the monitor port of the system unit.12Depending on the connector, plug the monitor power cable into either the system unit (1) or thegrounded power outlet (2).!You may only plug the monitor power cable into the monitor connector if the rated currentof the monitor is less than 1.5 A (230 V) or 3 A (115 V). The rated current for the monitoris also given on the monitor itself and in the Operating Manual for the monitor.
Preparation for use and operation Connecting the PC to the line voltage14 A26361-K520-Z100-1-7619Connecting the PC to the line voltage100 V - 125 V 200 V - 240 V1 11 = Notch for inserting the screwdriverCheck the rated voltage.!The value marked with an arrow must agree with the local line voltage:115 = 100 V to 125 V 230 = 200 V to 240 VIf the rated voltage does not agree with the local line voltage, lift out the plug-in unit with ascrewdriver (1), turn it and replace it.21Plug the system unit's power cable into the system unit (1) and then into the grounded poweroutlet (2).
Unlocking/locking the system unit Preparation for use and operationA26361-K520-Z100-1-7619 15Unlocking/locking the system unitWith the casing lock you can mechanically lock the system unit, and with the drive cover you canblock access to the drives.Unlocking the system unit12Turn the key counterclockwise (1).Slide the drive cover in direction of the arrow (2).Locking the system unit21Slide the drive cover in direction of the arrow (1) and turn the key clockwise (2).
Preparation for use and operation Switching the PC on and off16 A26361-K520-Z100-1-7619Switching the PC on and off1230I1 = Main switch2 = ON/OFF switch3 = Power-on indicator0 = System unit is switched off I = System unit is ready-to-operateSystem unit is offThe main switch (1) is in position 0, the power-on indicator (3) does not light, and the ON/OFFswitch (2) is disabled.System unit is ready-to-operateThe main switch (1) is in position I and the power-on (3) indicator lights up orange or flashesgreen/orange. In this mode, you can switch the system unit on with the ON/OFF switch (2). The"ready-to-operate" status corresponds to the "stand-by" status of a TV set. The exact description ofthe power-on indicator (3) is contained in the section "Indicators on the system unit".System unit is onThe main switch (1) is in position I and the power-on indicator (3) lights up green. The system unitcan be switched ready-to-operate at the ON/OFF switch (2).
Switching the PC on and off Preparation for use and operationA26361-K520-Z100-1-7619 17Switching on the PC for the first timeWhen you switch on your PC for the first time the supplied software is set up and configured.iIf the PC is integrated into a network, the user and server details as well as the networkprotocol are required. Contact your network administrator if you have any questions aboutthese details.The license number for Windows is printed on the front cover of the Windows manualsupplied.Switch your monitor on.Switch the system unit on with the ON/OFF switch.The power-on indicator lights green and the PC is started.!While the PC boots the screen remains dark for up to a minute depending on the systemconfiguration. To see the start-up messages, you can switch off the standard setting in theBIOS setup in the Quiet Boot entry.Adjust the brightness if necessary (see the Operating Manual for the monitor).!Some variants require you to start the software installation by pressing the function key.Once the installation has been started the PC must not be switched off.You should only reboot the PC during installation if you are requested to do so. Otherwisethe installation will be not be performed correctly. If a fault occurs in the installation thecontents of the hard disk must be completely restored.During installation follow the instructions on the screen.Consult the operating system manual if there is anything unclear about the requested input data.Some system configurations do not include a Windows CD in the delivery package. In this case youshould create a backup copy after installing Windows so that you can restore the hard disk contentsin an emergency.You need about 40 diskettes for this.Create Windows diskettes with the MSCSD backup program (create system diskettes) and labelthem using the labels supplied.iYou will find further information about the system, drivers, utilities, updates, and manualsetc. on the "Drivers & Utilities" CD supplied.
Preparation for use and operation Switching the PC on and off18 A26361-K520-Z100-1-7619Switching on the PCSwitch the monitor on (see the Operating Manual for the monitor).Switch the system unit on with the main switch at the rear of the system unit.If the power-on indicator lights orange, press the ON/OFF switch at the front of the system unit.The power-on indicator lights green and the PC is started.!While the PC boots, the screen remains dark for up to a minute depending on the systemconfiguration. To see the start-up messages, you can switch off this standard setting inthe BIOS Setup in the Quiet Boot entry.If you have assigned the system password, you must enter this when requested to do so,in order to start the operating system.Switching off the PCShut down the operating system properly. Windows in the Start menu via the Quit function.If the operating system does not automatically switch the system unit off, switch the systemunit to ready-to -operate by pressing the ON/OFF switch or turn it off by pressing the mainswitch when requested to do so.If the system unit is ready-to-operate, the power-on indicator lights up orange. The system unitconsumes a minimum of energy and can be switched on by an external device (provided that theremote-on functionality is enabled in BIOS Setup).When the system unit is switched off with the main switch the power-on indicator is dark afterapprox. 15 seconds. The system unit no longer uses any power.iThe main switch and the ON/OFF switch do not disconnect the system unit from the linevoltage. To disconnect the line voltage completely, remove the power plug from thegrounded power outlet.Placing a PC (with soft power off function) in a ready-to-operate state by means of softwarePrerequisite: Your system must support switching off with software and this functionality must beenabled in BIOS Setup (Soft Power OFF - Enabled). In addition, the soft off software must be installedon Windows NT systems.You can switch your PC ready-to-operate under Windows 9x or Windows NT via theShutdown the Computer menu or by using the DeskOff program.
Indicators on the system unit Preparation for use and operationA26361-K520-Z100-1-7619 19Indicators on the system unit2314561 = Power-on indicator2 = Hard disk indicator3 = Message indicator4 = CD-ROM indicator5 = Chipcard reader indicator6 = Floppy disk indicator1 - Power-on indicator− green:The System unit is on.− orange:The System unit is ready-to-operate.In this mode the PC consumes very little power and can be switched on at the ON/OFFswitch. If the remote-on function is Enabled in the BIOS Setup, the system unit can beswitched on by an incoming message (e. g. fax, telephone call).− flashes green/orange:The indicator only flashes on systems which support the ACPI function (AdvancedConfiguration and Power Interface).The system unit is in the energy-saving mode (standby). After being switched on with theON/OFF switch, the PC returns to the state it was in before the energy-saving mode. Inthe energy-saving mode the system unit may not be switched off with the main switch ordisconnected from the mains supply, as this may otherwise result in data loss.− does not glow:The system unit is switched off.2 - Hard disk indicatorThe indicator lights up when the hard disk drive of the system unit is accessed.3 - Message indicatorThe display glows or flashes when the system has received a message or has reported amalfunction. A detailed description can be found in the Technical Manual for the system board.4 - CD-ROM indicatorThe indicator lights up when the CD-ROM drive of the system unit is accessed. You may onlyremove the CD when the indicator is dark.
Preparation for use and operation Keyboard20 A26361-K520-Z100-1-76195 - Chipcard reader indicatorThe indicator lights up when the chipcard reader is accessed. You may only remove the chipcardwhen the indicator is dark.6 - Floppy disk indicatorThe indicator lights up when the floppy disk drive of the system unit is accessed. You may onlyremove the floppy disk when the indicator is dark.Keyboard134521 = Function keys2 = ON/OFF switch (optional)3 = alphanumeric keypad4 = Cursor control keys5 = numeric keypad (calculator keypad)
Keyboard Preparation for use and operationA26361-K520-Z100-1-7619 21Important keys and key combinationsThe following description of keys and key combinations refers to MS Windows. Details of other keysand key combinations can be found in the documentation of the relevant application program.ON/OFF switchDepending on the setting in the BIOS setup, the system can be switched on, off or onand off with this switch.Enter keyconfirms or starts the marked selection. The enter key is also referred to as the"Return" key or "Carriage Return".Start keyinvokes the START menu of Windows.Menu keyinvokes the menu for the marked item.Shift keyenables upper-case letters and the upper key symbols to be displayed. Alt Gr Alt Gr keyproduces a character shown on the right-hand side of a key (e. g. the character "\"on the key on a German keyboard).%5$4Euro keyenables the output of the Euro symbol.Num Num Lock keyby pressing the Num Lock key you switch between the upper- and lower-case levelsof the calculator keypad.At upper-case level (Num Lock indicator lit) the digit and comma keys are active.At lower-case level (Num Lock indicator not lit) the cursor control functions areactive in the calculator keypad.CtrlCtrl keystarts key combination actions. Ctrl Alt DelWarm bootrestarts your PC. First hold down the and key, andthen press the key. With Windows 9x the Task Managerappears first. The warm start is then carried out the secondtime.
Preparation for use and operation Working with floppy disks22 A26361-K520-Z100-1-7619Working with floppy disks!Follow the instructions supplied by the vendor of the floppy disks.Never clean the floppy disk drives with cleaning disks. Even just one attempt woulddestroy the read/write head in the disk drive within 20 seconds.32156471 = Insertion direction2 = Label area3 = Write protection tab for a 720 Kbyte or a 1.44 Mbyte floppy disk4 = Identification of a 1.44 Mbyte floppy disk or write protect tab on a 120 Mbyte floppy disk5 = Eject button for inserted floppy disks6 = Floppy disk is write protected7 = Floppy disk is not write-protectedTo insert a floppy disk, push it into the drive in the insertion direction (1) until it engages. Thelabel should be facing upward.To remove the floppy disk, press the eject button (5).The write-protect slider enables you to protect the data on the floppy disk from inadvertentoverwriting or deletion.To protect the data on the floppy disk from being overwritten, push the write-protect slider toposition (6). The hole is now visible.To remove write protection, push the slider to position (7). The hole is now covered.
Settings in BIOS Setup Preparation for use and operationA26361-K520-Z100-1-7619 23Settings in BIOS SetupThe BIOS Setup menu allows you to set your hardware configuration and system functions. When thePC is delivered, the default entries are valid (see Technical Manual for the system board or in themanual "BIOS Setup"). You can customize these settings to your requirements in BIOS Setup.The technical manual of the system board or the "BIOS Setup" manual shows you how to open anduse the BIOS Setup. The menus and setting options provided by BIOS-Setup are also described indetail.Property and data protectionThe software functions and mechanical lock on your PC enables you to protect your system andpersonal data in a number of ways against unauthorized access. By combining these options, youcan achieve optimum protection for your system.Locking the system unit mechanicallyWith the casing lock you can mechanically lock the system unit, and with the drive cover you canblock access to the drives.Access authorization via chipcardIn systems that are equipped with a chipcard reader, access can be restricted to users who have acorresponding chipcard.Security functions under WindowsUnder MS-Windows you can activate a screen saver and protect it with a password. Only thoseusers who know the password can deactivate the screen saver and access any open files. Detailedinformation on screen savers under MS Windows is provided by the associated help function.Security functions under Windows NTYou can use the SSLAUNCH program to start the screen saver POWERSAVER immediately. Theseprograms are located on the "Drivers & Utilities" CD.Information on POWERSAVER and SSLAUNCH can be found in the POWERSAV.HLP andSSLAUNCH.EXE files.Security functions under Windows 9xYou can lock the keyboard and mouse with a password-protected screen saver.
Preparation for use and operation Property and data protection24 A26361-K520-Z100-1-7619BIOS Setup security functionsThe Security menu in BIOS Setup offers you various options for protecting your personal data againstunauthorized access, e. g.:• Preventing unauthorized BIOS Setup calls• Preventing unauthorized system access• Preventing unauthorized access to the settings of boards with their own BIOS• Preventing system booting from the diskette drive• Activating virus warnings• Preventing unauthorized writing of diskettes• Protecting BIOS from overwriting• Protecting PC from being switched on by an external deviceBy combining these options, you can achieve optimum protection for your system.You will find a detailed description of the Security menus and how to assign passwords in theTechnical Manual for the system board or in the "BIOS Setup" manual.Theft protection and lead sealingWith a chain lock and the hole in the tab (1) or with the Kensington Lock device (2) and with aKensington MicroSaver you can protect your unit from theft.To prevent unauthorized persons from opening the system unit, the casing can be lead-sealed. Todo this, use the eyes on the back of the casing.21
A26361-K520-Z100-1-7619 25Troubleshooting and tips!Take note of the safety notes in the manual "Safety, Guarantee and Ergonomics" and inthe chapter "Preparation for use and operation", when you connect or disconnect cables.If a fault occurs, try to correct it as described:• in this chapter• in the documentation of the connected devices• in the help systems of the software used.If you fail to correct the problem, proceed as follows:Switch the PC off.Make a note of the steps and the circumstances that led to the fault. Also make a note of anyerror messages displayed and the Ident-No. of your device.Contact your sales office or our customer service.Installing new softwareWhen installing programs or drivers, important files may be overwritten and modified. To be able toaccess the original data in the case of any problems following installation, you should make abackup of the your hard disk prior to installation.Power-on indicator remains dark after you haveswitched on your deviceThis may have the following causes:The line voltage supply is faultyCheck that the power cable is plugged properly into the system unit and grounded power outlet.Switch the PC on at the main switch.Internal power supply overloadedDisconnect the power plug of the system unit from the grounded power outlet.Wait for a moment.Plug the power plug into the grounded power outlet again.Switch the PC on at the main switch.
Troubleshooting and tips26 A26361-K520-Z100-1-7619The screen stays blankIf your screen remains blank this may have the following causes:Monitor is switched offSwitch your monitor on.The PC is startingWhile the PC boots, the screen remains dark for up to a minute depending on the systemconfiguration. To see the start-up messages, you can switch off this standard setting in the BIOSSetup in the Quiet Boot entry.Screen has been blankedPress any key on the keyboard.orDeactivate screen blanking (screen saver). Enter the appropriate password.Brightness control is set to darkSet the brightness control to light. For detailed information, please refer to the OperatingManual supplied with your monitor.Power cable or monitor cable not connectedSwitch off the monitor and the system unit.Check that the power cable is properly connected to the monitor and system unit or to thegrounded power outlet.Check that the monitor cable is properly connected to the system unit and monitor (if notpermanently attached).Switch on the monitor and the system unit.Wrong monitor has been set under Windows NTRestart the PC in standard VGA mode.Set the desired resolution in the Control Panel window using the Display program, and adjustthe monitor display as described in the Operating Manual.Wrong monitor has been set under Windows 9xRestart the PC.If the message Starting Windows 9x appears, press function key .The Windows 9x start menu appears.Select the option Safe mode or Safe mode with network support.Set the correct values for the attached monitor by selecting Start - Settings - Control Panel -Display - Settings.The wrong RAM memory modules have been insertedSee the Technical Manual for the system board for information on which memory modules can beused.
Troubleshooting and tipsA26361-K520-Z100-1-7619 27No mouse pointer displayed on the screenShut down the operating system properly.Switch the PC off.Check that the mouse cable is properly connected to the system unit.If you use an adapter or extension lead with the mouse cable, check the connector.Make sure that only one mouse is connected.Switch the PC on.The mouse controller must be enabled, if you use a PS/2 mouse. Check in the BIOS Setup thatthe mouse controller is enabled.Check that the mouse driver is properly installed and is present when the application programis started. Detailed information can be found in the User Guide of the mouse or applicationprogram.The floppy disk cannot be read or writtenCheck that the write protection of the floppy disk or the floppy disk drive is activated (refer alsoto the Technical Manual of the system board or in the manual BIOS).Check the relevant entries for Diskette A: or B: in the Main menu of the BIOS Setup.Check that the floppy disk drive controller is enabled (refer also to the Technical Manual of thesystem board or in the manual "BIOS Setup").Check that the cables of the floppy disk drive are properly connected (refer to chapter "Systemexpansions").Time and/or date is not correctSet the time and/or date. You can set the time and date in the BIOS Setup or in the operatingsystem.iIf the time and date are repeatedly wrong when you switch on your PC, the battery is flat.Change the lithium battery as described in the Chapter "System expansions".Error messages on the screenError messages and their descriptions are listed in the Technical Manual of the system board or inthe "BIOS Setup" manual and in the documentation of the installed software.
Troubleshooting and tips28 A26361-K520-Z100-1-7619Restoring the hard disk contentsInstructions for this purpose can be found in the documentation (booklet) of theCD "Drivers & Utilities".TipsThe PC cannot be switched off with the ON/OFF switchCause: The PC has not been switched on with the ON/OFF switch.Press the ON/OFF switch again.Cause: System crashPress the ON/OFF switch for at least four seconds, until the device switches off.PC switches on briefly and then off againThe power cable has been plugged in or the device was switched on with the main switch. Fortechnical reasons, this brief switching on and off is necessary.Out of system resourcesIf you have too many applications running at once, you may experience problems due to a lack ofsystem resources. If this happens, you should close applications you do not require or call theapplications in a different order.BIOS settings in power management do not become activeThe Auto insert notification setting may be active for the CD-ROM drive. This setting causesWindows 9x to inquire about any modifications on the drive at regular intervals. Because of this thetimer for the idle time cannot time out.To activate power management, proceed as follows:In Windows 9x, select Start - Settings - Control Panel - System - Device Manager - CD-ROM.Select the installed CD-ROM drive from the list.Select Settings.Deactivate the Auto insert notification box.CD-ROM driveInformation on the CD-ROM drive can be found in the manual of the CD-ROM drive or on the"Drivers & Utilities" CD.Other manualsOther manuals are contained on the "Drivers & Utilities" CD.
A26361-K520-Z100-1-7619 29System expansions!It may be necessary to update the BIOS when carrying out a system expansion orhardware upgrade. In this instance, please contact our service.When installing components with a high power loss, make sure that the maximumpermissible temperatures of the individual components are not exceeded.This chapter describes all the activities required to modify your PC hardware (e.g. installing boardsor drives).Memory and processor upgrading are described in the Technical Manual for the system board.Read the supplied documentation before installing new drives and/or boards.Refer to the Technical Manual for the system board before making any extensions on the systemboard.Opening the system unitSwitch the PC off.!Please take note of the safety information in the chapter "Important notes".Pull the power plug out of the power outlet!If any cables attached to the system unit are obstructing you, pull out the connectors on thesystem unit.Place the system unit in a convenient working position.
System expansions30 A26361-K520-Z100-1-76192a3 41Unlock the system unit (1).Unlock the top cover with the locking slide at the rear of the casing by sliding it to the left (2).Push the top cover in the direction of the arrow (3) until the distance (a) isapproximately 10 mm.Lift off the top cover in an upward direction (4).Assembling the system unit3a2 1Place the top cover on the system unit (1) from above so that the distance (a) isapprox. 10 mm.Push the top cover in the direction of the arrow (2) until it engages.Lock the top cover using the locking slide at the rear (3).Return the system unit to its original position.If you have disconnected cables, reconnect them at the rear.
System expansionsA26361-K520-Z100-1-7619 31Installing and removing a board!Observe the notes on installing and removing boards in the chapter "Important notes".Old ISA boards which require a -5 V power supply are not supported.The number, position and constellation of the board slots on the system board can be found in thetechnical manual for the system board. Boards may be installed when the device is shipped.Any angled slot is intended for high PCI boards including connectors and cables. However, you canalso install an ISA board.Installing a boardOpen the system unit (see "Opening the system unit").312Press on the clip in the direction of the arrow (1) and remove it (2).Remove the rear slot cover plate from the slot (3).!Do not dispose of the rear slot cover plate. For cooling, protection against fire and in orderto comply with EMC regulations, you must refit the rear slot cover plate if you remove theboard.Take the new board out of its packaging.Make the required settings for the board.
System expansions32 A26361-K520-Z100-1-76191a32Push the board into the slot (1).Ensure that the end of a long board without angle bracket fits into the corresponding guide ofthe system unit. Ensure also that the point of the angle bracket slots into guide (a).Press the board into the slot so that it engages.Replace the clip (2) which fixes the board. Make sure that the clip engages when released (3).If necessary, plug the lines on the board.Close the system unit (see "Assembling the system unit").Removing a boardOpen the system unit (see "Opening the system unit").Remove the lines connected to the board.312Press on the clip in the direction of the arrow (1) and remove it (2).Remove the board from the system unit (3).Place the board into an appropriate packaging.!For cooling, protection against fire and in order to comply with EMC (electromagneticcompatibility) regulations, you must refit the rear slot cover plate.
System expansionsA26361-K520-Z100-1-7619 33132aPush the rear slot cover plate into the slot (1). Ensure that the point of the cover engages intothe guide (a).Replace the clip (2) which fixes the board. Make sure that the clip engages when released (3).Close the system unit (see "Assembling the system unit").iIf you have installed or removed a PCI board, please check in the BIOS Setup the settingsfor the relevant PCI slot. If necessary, change the settings. Further information is providedin the documentation for the PCI board.
System expansions34 A26361-K520-Z100-1-7619Installing and removing drivesThe system unit houses a total of three accessible drives (two 5 1/4-inch drives and one 3 1/2-inchdrive) and two non-accessible half-height (Slimline) drives .IDE drivesBy default four IDE drives are supported. Ideally hard disks are connected to IDE port 1, andaccessible IDE drives, for example CD-ROMs, to IDE port 2 (see also the Technical Manual for thesystem board).SCSI drivesIf you want to install an SCSI drive, you require an SCSI controller and an SCSI cable. Note that:• not every SCSI controller is suitable for operating SCSI hard disks• each SCSI device must be assigned its own SCSI-ID• the SCSI cable must always be terminated at the end, either by a drive or by a terminatingresistor on the cable. The terminating resistors of all other SCSI devices attached must not beactivated or connected.• Depending on the SCSI technology (UW, U2W), an adapter may be required for terminating theSCSI drives with a 50-pin connector.Installing an accessible driveOpen the system unit (see "Opening the system unit").iShould the chipcard reader get in the way of the accessible drive during installation, thenremove the reader (see "Installing/removing a chipcard reader").AB12Pry the plastic drive cover (A) out of the front cover.Pry the shielding plate (B) on left-hand side out of the bay.!Do not throw away the covers. If you remove the drive again later, you will have toreinstall the covers.Take the new drive out of its packaging.Make the required settings on the drive (if necessary, on installed drives as well).
System expansionsA26361-K520-Z100-1-7619 3521ABA = Position of the screw for the upper driveB = Position of the screw for the lower driveSlide the drive into the system unit (1).Plug the data and the power supply connectors into the drive.Fasten the drive with the screw (2).If you have removed the chipcard reader, then reinstall it.Close the system unit (see "Assembling the system unit").iIf necessary, you must adapt the entry for the drive in the Setup menu.
System expansions36 A26361-K520-Z100-1-7619Removing an accessible driveOpen the system unit (see "Opening the system unit").Pull the data and the power supply connectors from the desired drive.iShould the chipcard reader get in the way of the accessible drive during installation, thenremove the reader (see "Installing/removing a chipcard reader").12ABA = Position of the screw for the upper driveB = Position of the screw for the lower driveRemove the relevant screw (1) and take the drive out of the system unit (2).ABInsert the shielding plate (B) on the right-hand side on the installation bay and press it in.Press the plastic drive cover (A) into the front panel until it snaps in place.If you have removed the chipcard reader, then reinstall it.Close the system unit (see "Assembling the system unit").iIf necessary, you must adapt the entry for the drive in the Setup menu.
System expansionsA26361-K520-Z100-1-7619 37Changing the floppy disk driveOpen the system unit (see "Opening the system unit").Remove the hard disk carrier (see "Installing and removing the hard disk drive").12Pull the data and the power supplyconnectors from the floppy disk drive.Remove the screw (1) and take the driveout of the system unit (2).Take the new floppy disk drive out of itspackaging.21Push the drive into the system unit (1), andfix it with the screw (2).Plug the data and the power supplyconnectors into the floppy disk drive.Remove the hard disk carrier (see"Installing and removing the hard diskdrive").Close the system unit (see "Assemblingthe system unit").iIf necessary, you must adapt the entry for the drive in the Setup menu.
System expansions38 A26361-K520-Z100-1-7619Installing and removing the hard disk driveOpen the system unit (see "Opening the system unit").Removing the hard disk carrier2134Lift the hard disk carrier out of the mounting in the direction of the arrow (1) and (2).Lift the hard disk carrier out of the system unit in the direction of the arrow (3) and (4).Pull the data and power supply connectors from the hard disk drive or the hard disk drives.Installing the first hard disk driveTake the new hard disk drive out of its packaging.Make the required settings (e.g. master/slave, stand alone) on the drives.2213Insert the hard disk drive into the plastic bracket (1). The drive must engage in the plasticnipple.Fold the plastic bracket in the direction of the arrow (2) on the hard disk drive.Push the hard disk drive into the drive bracket until the plastic bracket engages (3).
System expansionsA26361-K520-Z100-1-7619 39Installing the second hard disk drive2221Take the new hard disk drive out of itspackaging.Make the required settings (e.g.master/slave, stand alone) on the drives.Slide the hard disk drive into the drivecarrier (1).Fasten the drive with the screws (2).Removing the first hard disk drive12Lightly press on the clip (1).Pull the hard disk drive out of thecarrier (2).112Fold the plastic bracket in the direction ofthe arrow (1).Remove the hard disk drive (2).
System expansions40 A26361-K520-Z100-1-7619Removing the second hard disk drive2111Remove the screws (1).Pull the hard disk drive out of thecarrier (2).Make the required settings on theremaining hard disk drive(e.g. stand alone).Installing the hard disk carrier3421Plug the data and the power supply connectors into the hard disk drive or into the hard diskdrives.Lift the hard disk carrier into the system unit in the direction shown by the arrow (1) and push itforward until it engages (2).Press the hard disk carrier in the direction of the arrow (3) and press it downward (4).Close the system unit (see "Assembling the system unit").iIf necessary, you must adapt the entry for the drive in the Setup menu.
System expansionsA26361-K520-Z100-1-7619 41Installing/removing a chipcard readerOpen the system unit (see "Opening the system unit").Installing a chipcard readerRemove the cover.312Fix the cable on the chipcard reader (1) and on the connector for the chipcard reader on thesystem board (see the Technical Manual of the system board).Lift the chipcard reader into the system unit (2).Push the chipcard reader in the direction of the arrow (3) until it clicks into position. Pressdownward and toward the drive cage while doing so.iWith the chipcard reader connected, no devices may be connected to serial port 2.Removing a chipcard reader2314Pull the cable off the chipcard reader and off the connector for the chipcard reader on thesystem board (see the Technical Manual of the system board).Press on the clip (2) and pull the chipcard reader in the direction of the arrow (3).Lift the chipcard reader out of the system unit (4).Mount the cover in place of the chipcard reader. It may be necessary to secure the cover with ascrew.
System expansions42 A26361-K520-Z100-1-7619Installation opening for 2nd serial portAn installation opening for the 2nd serial port is provided on the back of the casing. As a result, thismeans no board slot is occupied.Insert a screwdriver into the opening and break out the pre-stamped installation opening bymoving back and forth.Extensions on the system boardDetails of how and if you can upgrade the main memory or the processor of your PC are provided inthe Technical Manual for the system board. Below the necessary steps are described to enable youto work on the system board.Open the system unit (see "Opening the system unit").Upgrading main memoryUpgrade the memory as it is described in the Technical Manual for the system board.Close the system unit (see "Assembling the system unit").
System expansionsA26361-K520-Z100-1-7619 43Replacing processor and lithium batteryTo replace the processor and the lithium battery, you must remove the ventilation duct.Removing ventilation duct23411Press the clip together (1).Lift the ventilation duct slightly (2) and guide the ventilation duct out of the guide holes (3).Remove the ventilation duct from the unit (4).You have free access to the locations.Replacing processorMake the desired expansions (see the Technical Manual for the system board).Replacing lithium battery!Incorrect replacement of the lithium battery may lead to a risk of explosion.The lithium battery may be replaced only with an identical battery or with a typerecommended by the manufacturer.Do not throw lithium batteries into the trashcan. It must be disposed of in accordance withlocal regulations concerning special waste.Make sure that you insert the battery the right way round. The plus pole must be on thetop!123++++Lift the contact (1) a few millimeters and remove the battery from its socket (2).Insert a new lithium battery of the same type in the socket (3).
System expansions44 A26361-K520-Z100-1-7619Installing ventilation duct43122Lift the ventilation duct into the unit (1)Press the clip together (2).Insert the ventilation duct into the guide holes (3) in the power supply.Push the ventilation duct downward until the clip engages (4).Close the system unit (see "Assembling the system unit").
A26361-K520-Z100-1-7619 45Technical dataElectrical dataRegulations complied with: EN 60950 / VDE 0805UL 1950CSA 22.2 No.950Protection class: IRated voltage range: (selectable) 100 V to 125 V / 200 V to 240 VFrequency: 50 Hz - 60 HzMax. rated current• System unit with monitor socket:• Monitor socket (output)100 V - 125 V / 5,5 A200 V - 240 V / 3,0 A100 V - 125 V / 3 A200 V - 240 V / 1.5 ATypical power draw in operation:Power draw in energy saving mode:Power draw in the 'ready' status< 35 W *)< 28 W *)< 3 W *)DimensionsWidth/Depth/Height:Weight: 454 mm/473 mm/139 mmca. 11 kg (107,9 N) in basic configurationEnvironmental conditionsEnvironment class (3K2)Environment class (2K2) DIN IEC 721 part 3-3DIN IEC 721 part 3-2Temperature:• Operating (3K2)• Transport (2K2) 15 °C .... 35 °C-25 °C .... 60 °CCondensation in operating must be avoided.Clearance required to ensure adequate ventilation:• left-hand side• front• rearmin. 200 mmmin. 200 mmmin. 200 mm!Do not place several system units one above the other.*) These values only apply for a SCENIC 600 with the configuration below. When additionalcomponents are incorporated, the power consumption in energy saving mode may exceed therequirements for the environment symbol ("Blue Angel") (30 W).Processor (512 Kbyte cache):Main memory:Floppy disk drive:Hard disk drive:CD-ROM drive:Graphics:LAN:Pentium II MMX at 450 MHz192 Mbytes1.44 Mbytes6,4 Gbyte32foldMatrox MGA G100 AGP10/100 MBit Ethernet Controller onboard
A26361-K520-Z100-1-7619 47Index22. Serial port, installation opening 42AAccessible driveinstalling 34removing 36Accumulator, disposal 4Activating, security measures 23Alphanumeric keypad 20Alt Gr key 21Anti-theft protection 24Assembling, PC 30Audio input 11Audio output 11BBattery 43disposal 4BIOS Setup 23security functions 24Board 3installing 31removing 31CCableconnecting 10disconnecting 10Cabling, PC 10Calculator keypad 20Casing lock 15CD-ROM driveindicator 19installing 34manual 28removing 36CE certificate 5Changingfloppy disk drive 37hard disk drive 38lithium battery 43Checking, rated voltage 14Chipcard reader 11indicator 20Class B Compliance Statement 5Cleaning 8Clearance 45Configuration, BIOS-Setup 23
IndexA26361-K520-Z100-1-7619Connectingcables 10devices 10keyboard 12monitor 13mouse 12parallel port 12power voltage 14serial port 12Connecting to power voltage 14Contents of delivery 9Control key 21Courier 1Ctrl key 21Ctrl+Alt+Del 21Cursor control keys 20DDark screen 26Data protection 23Data, technical 45Date, not correct 27Devicesconnecting 10interface 11Dimensions 45Diskette 22cannot be read or written 27write-protection 22Displaycleaning 8Disposal 4Drive 34Drive cover 15EElectrical data 45Electromagnetic compatibility 5Energy saving 4Enter key 21Environmental conditions 45Environmental data 45Ergonomic, video workstation 10Errordate 27floppy 27mouse 27screen 26system unit 25time 27Error message 27ESD 3Euro key 21Expansion 29
IndexA26361-K520-Z100-1-7619External devicesconnecting 10ports 11FFCC statement 5Floppy disk drivechanging 37indicator 20removing 36Function keys 20GGame port 11Green, power-on indicator 19Guarantee coupon booklet 9HHard disk carrierinstalling 40removing 38Hard disk drive, replacing 38Hard disk indicator 19Housingassembling 30opening 29IIDE drives 34Important notes 3Indicator, on the PC 19Indicator, power-on indicator fails to light 25Installation opening, for 2nd serial port 42Installation, new Software 25Installingaccessible drive 34board 31hard disk carrier 40hard disk drive 38, 39ventilation duct 44Insufficient memory 28Interfaces 11Italics 1KKensington Lock 24Key combination 21Keyboard 20cleaning 8connecting 12Keyboard port 11Keys 21
IndexA26361-K520-Z100-1-7619LLAN-port 11Lcok 15Lead-sealing 24Line in 11Line out 11Lithium battery 42replacing 43Locking, PC 15MMain memory 42Main switch 16Manuals, other 28Manufacturer’s notes 4Memory, upgrading 42Menu key 21Message indicator 19Microphone jack 11Monitorconnecting 13transporting 7Monitor port 11Mousecleaning 8connecting 12error 27Mouse port 11NNew Installation, Software 25No screen display 26Not enough memory 28Notational conventions 1Noteboards 3CE certificate 5disposal 4energy saving 4important 3manufacturer 4power cord selecction 5safety 3Num Lock key 21Numeric keypad 20OON/OFF switch 16, 21Opening, system unit 29Operation 9Orange, power-on indicator 19Other manuals 28OverviewPC 1
IndexA26361-K520-Z100-1-7619preparing for use 9PPacking material 9Parallel interface 11connecting devices 12PC cabling 10cannot boot 25cleaning 8closing 30connecting 10connecting to power voltage 14indicators 19locking 15opening 29ports 11setting up 10switching off 16, 18switching on 16, 18switching on for the first time 17transporting 7unlocking 15Ports, external devices 11Power cord selecction 5Power management 28Power-on indicator 16, 19blinking 19dark 25Preparation for use 9overview 9Problems 25processor 42Processor, replacing 43Property protection 23PS/2 mouse port 11QQuiet Boot 26RRated voltagesetting 14Ready-to-operate 16Recycling 4Reinstalling, hard disk contents 28Removingaccessible drive 36board 31hard disk carrier 38hard disk drive 39, 40ventilation duct 43Replacingboard 31
IndexA26361-K520-Z100-1-7619hard disk drive 38lithium battery 43Replacing, lithium battery 43Restoring, hard disk contents 28Return key 21SSafety 3Screenblank 17, 18, 26stays blank 26Screen blanking 4SCSI drives 34Security functions 24Chipcard 23lock 23MS-Windows 23Security measures 23Selectpower cord 5Serial interface 11connecting devices 12Setting, rated voltage 14SettingsBIOS Setup 23Setup, see BIOS SetupShift key 21Soft Power Off 18Software, new Installation 25Start key 21Streamerinstalling 34removing 36Summer time 27Surface 45Switching off, PC 16, 18Switching on, for the first time 17Switching on, PC 16, 18Symbols, explanation of 1System board, extensions 42System expansion 29System settings, BIOS Setup 23System unit, see PCTTechnical data 45Time, not correct 27Tips 25, 28Transport 7Troublefloppy 27mouse 27screen 26system unit 25
IndexA26361-K520-Z100-1-7619Troubleshooting 25UUnlocking, PC 15Unpacking 9Upgrading, memory 42USB, Universal Serial Bus 11VVentilation area 45Ventilation ductinstalling 44removing 43VESA (DPMS) 4Video workstation 10WWarm boot 21Winter time 27Write protection, floppy 22
A26361-K520-Z100-1-7619ContentsIntroduction..................................................................................................................................... 1Notational conventions...................................................................................................................... 1Important notes............................................................................................................................... 3Safety ............................................................................................................................................... 3Notes on installing and removing boards................................................................................... 3Manufacturer's notes......................................................................................................................... 4Energy saving ........................................................................................................................... 4Disposal and recycling .............................................................................................................. 4CE certificate ............................................................................................................................ 5FCC Class B Compliance Statement ........................................................................................ 5Power cord selection......................................................................................................................... 5For the United States and Canada............................................................................................ 6For the United Kingdom ............................................................................................................ 7Transporting the PC.......................................................................................................................... 7Cleaning the PC................................................................................................................................8Preparation for use and operation................................................................................................. 9Unpacking and checking the delivery................................................................................................ 9Preparing the PC for use................................................................................................................... 9Setting up the PC............................................................................................................................ 10Connecting devices......................................................................................................................... 10Ports for external devices........................................................................................................ 11Connecting the keyboard ........................................................................................................ 12Connecting the mouse ............................................................................................................ 12Connecting devices with serial or parallel port......................................................................... 12Connecting the monitor to the line voltage .............................................................................. 13Connecting the PC to the line voltage ............................................................................................. 14Unlocking/locking the system unit................................................................................................... 15Switching the PC on and off............................................................................................................ 16Switching on the PC for the first time ...................................................................................... 17Switching on the PC................................................................................................................ 18Switching off the PC................................................................................................................ 18Indicators on the system unit .......................................................................................................... 19Keyboard ........................................................................................................................................ 20Important keys and key combinations ..................................................................................... 21Working with floppy disks................................................................................................................ 22Settings in BIOS Setup ................................................................................................................... 23Property and data protection........................................................................................................... 23Locking the system unit mechanically..................................................................................... 23Access authorization via chipcard........................................................................................... 23Security functions under Windows .......................................................................................... 23BIOS Setup security functions ................................................................................................ 24Theft protection and lead sealing ............................................................................................ 24Troubleshooting and tips............................................................................................................. 25Installing new software.................................................................................................................... 25Power-on indicator remains dark after you have switched on your device....................................... 25The screen stays blank................................................................................................................... 26No mouse pointer displayed on the screen ..................................................................................... 27The floppy disk cannot be read or written........................................................................................ 27Time and/or date is not correct ....................................................................................................... 27Error messages on the screen ........................................................................................................ 27
ContentsA26361-K520-Z100-1-7619Restoring the hard disk contents.....................................................................................................28Tips28System expansions.......................................................................................................................29Opening the system unit..................................................................................................................29Assembling the system unit.............................................................................................................30Installing and removing a board.......................................................................................................31Installing and removing drives.........................................................................................................34Installing an accessible drive...................................................................................................34Removing an accessible drive.................................................................................................36Changing the floppy disk drive.................................................................................................37Installing and removing the hard disk drive..............................................................................38Installing/removing a chipcard reader..............................................................................................41Installation opening for 2nd serial port...............................................................................................42Extensions on the system board......................................................................................................42Upgrading main memory.........................................................................................................42Replacing processor and lithium battery..................................................................................43Technical data...............................................................................................................................45Index...............................................................................................................................................47
A26361-K520-Z100-1-7619A26361-K520-Z100-1-7619SCENIC 600Operating ManualJanuary 1999 editionMicrosoft, MS, MS-DOS, Windows and Windows NT are Trademarks of Microsoft Corporation.VESA and DPMS are trademarks of Video Electronics Standards Association.PS/2 is a registered trademark of International Business Machines, Inc.Pentium is a registered trademark of Intel Corporation, USA.Acrobat Reader is a trademark of Adobe Systems Incorporated.All other trademarks referenced are trademarks or registered trademarks of their respective owners,whose protected rights are acknowledged.Copyright  Siemens AG 1998All rights, including rights of translation, reproduction by printing, copying or similar methods, even ofparts are reserved.Offenders will be liable for damages.All rights, including rights created by patent grant or registration of a utility model or design, arereserved.Delivery subject to availability. Right of technical modification reserved.

Navigation menu