Fujitsu F04B Fujitsu F-04B Cellular Phone User Manual F 04B E H1 eps

Fujitsu Limited Fujitsu F-04B Cellular Phone F 04B E H1 eps

manual part 3

F-04B_E1kou16IntroductionHandling precautions・Keep water away from FOMA terminal.- FOMA terminal, battery pack, adapter and UIM are not waterproof. Do not use FOMA terminal in bathrooms or other high-humidity areas, or in the rain. When carrying FOMA terminal in a pocket near your body, sweat may corrode the inner components, causing malfunction. Malfunctions deemed to be caused by water are not covered by the warranty, and may be impossible to repair. Since these conditions are outside the scope of the warranty, a repair, if at all possible, is charged.・Clean FOMA terminal with a dry soft cloth (such as a cloth for eyeglasses).- The display of FOMA terminal may have been applied special coating to improve clearness of the color LCD. When cleaning FOMA terminal, rubbing it roughly with a dry cloth can scratch the display. Take care when handling the unit, and clean it with a dry soft cloth (such as a cloth for eyeglasses). Drops of water or dirt left on the display can cause stains or remove the coating.- If FOMA terminal is wiped with alcohol, paint thinner, benzine or detergent, the printing may disappear or color may fade.・Clean the jack occasionally with a dry cotton swab etc.- If the jack is soiled, connection gets worse and it may cause power to be turned off or insufficient battery charge, so clean the jack with a dry cotton swab etc.Also, be careful never to damage the jack when cleaning it.・Do not place FOMA terminal near an air-conditioner outlet.- The rapid change in temperature may cause condensation, causing internal corrosion and malfunction.・When using, be careful not to subject excessive force to FOMA terminal or the battery.- If FOMA terminal is crammed into a brimming bag or placed in a pocket and sat on, display, internal PCBs or battery pack may be damaged or malfunction. And, if external devices are plugged into the external connection jack (earphone/microphone jack), the breakage of the connector or malfunction may result.・Carefully read the separate instructions that come with FOMA terminal, adapter and desktop holder.・Do not rub or scrape the display with a metal piece etc.- It may scratch the display, causing malfunction or damage.・Do not press the surface of the touch panel strongly or operate it with sharp objects such as a nail, a ballpoint pen and a pin.- It may damage the touch panel.・Avoid extreme temperature.- Use FOMA terminal where the temperature ranges between 5 and 35℃ and humidity ranges between 45 and 85%.・FOMA terminal may affect land-line phones, TVs or radios in use nearby, so use it as far as possible from these appliances.・Maintain a separate record of the data you saved in your FOMA terminal.- If the data is deleted, DOCOMO assumes no responsibility for the loss of any data.・Do not drop FOMA terminal or subject it to shocks.- May cause malfunction or damage.・Do not plug external devices into the external connection jack (earphone/microphone jack) at a slant, or do not pull it forcibly while it is plugged.- May cause malfunction or damage.・Do not close FOMA terminal with the strap etc. held inside.- May cause malfunction or damage.・It is normal for FOMA terminal to become warm during use or charging. Continue to use it.・Do not leave FOMA terminal with the camera in areas under strong direct sunlight.- May cause discoloring or burn-in of materials.・FOMA terminal should normally be used with the external connection jack cap closed.- Dust and/or water brought into FOMA terminal cause troubles.・Do not use FOMA terminal with the back cover removed.- May cause the battery to come off, or may cause a malfunction or damage.・Do not put label or sticker on the backside or keypad side of display unit, or backside of QWERTY keypad unit.- Getting stuck with the label or sticker when opening/closing FOMA terminal may cause malfunction or damage.General FOMA terminal
F-04B_E1kou17Introduction・While microSD card is being used, do not take the card out and do not turn OFF FOMA terminal.- May cause data loss or malfunction.・Do not bring magnetic cards etc. close to FOMA terminal.- Magnetic data in cash cards, credit cards, telephone cards, floppy disks, etc. may be erased.・Do not bring magnetized objects close to FOMA terminal.- Bringing strong magnetism close may cause a malfunction.・The battery pack is a consumable part.- Replace the battery pack if FOMA terminal has extremely short operation time on a full charge, though it may vary by operating conditions. Purchase a new battery pack of the specified type.・Charge the battery in an area within the proper ambient temperature range (5-35℃).・Always charge before using it for the first time or after extended disuse.・The operation time provided by the battery pack varies by the operating environment and battery pack's deterioration.・The battery pack may swell out as it comes to near the end of its lifetime depending on the usage conditions, but it is not a problem.・Be careful especially about the following points when preserving or leaving the battery pack for a long time.- Keeping under the state of the full charge (right after charging ends)- Keeping under the state of the empty charge (too exhausted to turn on FOMA terminal)They may cause the battery pack performance to be degraded or its lifetime to be shortened.For recommended battery level to keep for a long time, the display of battery icon is in a state of 2 cells as a guide.・Charge the battery in an area within the proper ambient temperature range (5-35℃).・Do not charge the battery in the areas below.- In areas of excessive humidity, dust or vibrations- Near land-line phones or TVs/radios・It is normal for the adapter to become hot while charging. Continue to use it.・When using the DC adapter for charging, keep the vehicle engine running.- The vehicle's battery could become flat.・When using an outlet with a mechanism preventing unplugging, follow the handling instructions for that outlet.・Do not give strong shock. Do not deform the charging jack.- Doing so may cause malfunction.Battery packAdapter
F-04B_E1kou18Introduction・Do not use excessive force to install/remove UIM.・It is normal for UIM to become warm during use. Continue to use it.・Note that DOCOMO assumes no responsibility for malfunctions occurring as the result of inserting and using a UIM with another IC card reader/writer.・Always keep UIM ICs clean.・Clean UIM with a soft, dry cloth (such as a cloth for eyeglasses).・Maintain a separate record of the data you saved in UIM.- If the data is deleted, DOCOMO assumes no responsibility for the loss of any data.・To preserve the environment, bring the old UIM to a sales outlet such as docomo Shop.・Avoid extreme temperature.・Take care not to scratch, touch accidentally or short IC.- May cause data loss or malfunction.・Do not drop UIM or subject it to shocks.- May cause malfunction.・Do not bend UIM or place heavy objects on it.- May cause malfunction.・Do not install UIM into FOMA terminal with a label or sticker put on UIM.- May cause malfunction.・This FOMA terminal is equipped with the security features, that are compliant with Bluetooth standards for communication via Bluetooth. However, depending on the settings, there may not be enough security. Be aware of security risks when using Bluetooth.・DOCOMO assumes no responsibility for any information which may be leaked during communication via Bluetooth.・You can use headset, handsfree, audio, keyboard, dial-up connection, object push and serial port devices with FOMA terminal. An audio/video remote control may be available with an audio device (only Bluetooth compatible devices).・To use FOMA terminal with separated into display unit and keypad unit, Bluetooth function is used.・Frequency bandsFrequency bands used by FOMA terminal Bluetooth function are as below.a2.4 : Radio equipment that uses the 2400 MHz band.bFH : The modulation is the FH-SS method.c1 : The expected interference distance is 10 m or shorter.d : All bandwidths between 2400 MHz and 2483.5 MHz are used, and the bandwidth used by mobile object identification devices cannot be avoided.Cautions on using Bluetooth devicesIn the bandwidth used by this terminal, in addition to home electric appliances such as a microwave oven and industrial/scientific/medical devices, in-plant radio stations used to identify mobile objects used in production lines of a factory that require a license, specified low power radio stations, or amateur radio stations that do not require a license (hereafter "other radio stations") can be in operation.1. Before using this terminal, check whether other radio stations are in operation in your neighborhood.2. If radio wave interference occurs between the terminal and "other radio stations", use the terminal in a different location or "Turn the power OFF" to avoid the radio wave interference.3. For more detailed information, contact the numbers for "General Inquiries" on the last page of this manual.UIMBluetooth® devicesabdc2.4FH1
F-04B_E1kou19Introduction・FeliCa reader/writer function of FOMA terminal uses weak waves requiring no licenses for radio stations.・It uses 13.56 MHz frequency band. When using other reader/writers in your surroundings, keep FOMA terminal away sufficiently from them. Before using the FeliCa reader/writer, confirm that there are no radio stations using the same frequency band nearby.・Do not use a remodeled FOMA terminal. Using a remodeled terminal violates the Radio Law.FOMA terminal is certified according to technical standard conformance of specified wireless equipment based on the Radio Law, and as a proof of it, the "Technical Compliance Mark " is depicted on the nameplate sticker of FOMA terminal.If you remodel FOMA terminal by removing its screws, your certification of technical standard conformance becomes invalid.Do not use FOMA terminal with its certification of technical standard conformance invalid as it violates the Radio Law.・Be careful when you use FOMA terminal while driving a car etc.Using a mobile phone while driving is subject to penal regulations.If you inevitably receive a call, tell the caller that you will "call back" by handsfree, then park in a safe place and call back.・Use the Bluetooth function only in Japan.The Bluetooth function of the FOMA terminal is compliant with wireless standards and is authorized for use only in Japan.If you use this function overseas, you may be punished.・Use FeliCa reader/writer function only in Japan.FeliCa reader/writer function of FOMA terminal conforms to Japanese radio standards.If you use this function overseas, you may be punished.FeliCa reader/writerCAUTION
F-04B_E1kou20Basic OperationBefore UsingOperating in separated styleTo operate from keypad unit in separated style, keypad unit should be registered as a Bluetooth device. Registering is automatically performed when FOMA terminal turns ON for the first time.*For detaching/attaching FOMA terminal's unit, hold FOMA terminal in hand.✜ DetachingPress separating button (a) and hold display unit up (b).When the unit detached, the arch light blinks and start Bluetooth connection between display unit and keypad unit automatically. While Bluetooth connection, or appears on the display and Bluetooth light on keypad unit turns on.✜ AttachingJoin the units with fitting convex part of keypad unit and concave part of display unit (a) and push until separating button clicks to fix them (b).Arch light blinks when the units are attached, and after a while, Bluetooth connection is disconnected.Point･To operate FOMA terminal with keypad unit, turn the power of both units ON. If the power of keypad unit is turned off or the unit is not recognized as Bluetooth device, Bluetooth connection does not start when separating FOMA terminal.･It takes approximately 4-5 seconds to use keypad unit after completion of Bluetooth connection with keypad unit detached (except for detaching during a call and when Continuous connection is set to "ON"). Please wait for blinking to end.･If units are attached when power ON/OFF status of each unit differ, keypad unit status is switched to the one of display unit.Separating buttonConvex part of keypad unitConcave part of display unit
F-04B_E1kou21Basic OperationWhile using detached keypad unit, HID support device (for key entering) or HFP and HSP support device (for talking) cannot be used at the same time. To use those Bluetooth devices, perform any of following procedures.【Procedure 1】 Attaching keypad unitAttach keypad unit to display unit to end Bluetooth communication of the keypad unit.【Procedure 2】 Selecting registered Bluetooth deviceWhen keypad unit is detached, mef*bemd to disconnect connection of keypad unit, select Bluetooth device to use and connect it.Point･Please verify the power of keypad unit OFF after turning the power of display unit OFF in areas where use is prohibited, such as in airplanes and hospitals.･When Continuous connection is set to "ON", battery power consumption is increased.Cautions on using detached keypad unitBefore UsingAttaching UIM (FOMA card)/battery packSet UIM (FOMA card) to display unit. For attaching/removing battery pack or UIM, separate the FOMA terminal, turn off the power of display unit and perform properly with holding display unit in hand.✜ Removing Back Cover F45With pressing the back cover with your thumb, slide approximately 3 mm in the direction of the arrow to remove it.✜ Installing UIMPull the tab with your nail and pull out the tray until it clicks (a). Hold UIM with the IC side up, align the beveled corner with the tray (b) and push into the tray until it stops (c).Attaching to display unitPress here with your thumbBack coverICCorner cutUIMTrayTab
F-04B_E1kou22Basic Operation✜ Attaching Battery Pack F13With label side of battery pack up, align convex parts of the battery pack with concave parts of FOMA terminal, slide the battery pack in the direction of a and then press it in the direction of b to set in.✜ Attaching Back Cover F45Place the 4 tabs of back cover to the notches, press back cover in the direction of a to avoid forming any clearance between FOMA terminal and back cover, then slide it in the direction of b to attach it.Point･UIM (blue) is not available for this FOMA terminal. If you have the UIM (blue), bring it to a docomo Shop.Separate FOMA terminal and turn off the power of keypad unit, and then perform properly with holding keypad unit in hand.✜ Removing Back Cover F46Hold keypad unit in one hand not to slide and with pressing a round mark of the back cover with your thumb of the other hand, and slide in the direction of the arrow approximately 3 mm to remove it.✜ Attaching Battery Pack F14With label side of battery pack up, align convex parts of the battery pack with concave parts of FOMA terminal, slide the battery pack in the direction of a and then press it in the direction of b to set in.✜ Attaching Back Cover F46Place the 4 tabs of back cover to the notches, press back cover in the direction of a to avoid forming any clearance between FOMA terminal and back cover, then slide it in the direction of b to attach it.Battery packConvex partConcave partBack coverAttaching to keypad unitPress here with your thumbBack coverBattery packConvex partConcave part
F-04B_E1kou23Basic OperationBefore UsingChargingThe battery pack does not have a full charge at time of purchase. Charge FOMA terminal in basic style for fully charging both battery packs of display unit and keypad unit aOpen jack cap (a) of FOMA terminal, hold the connector horizontally with the arrow side upward and insert it to the jack. (b)bUnfold the power plug and insert it into a 100V AC outlet.*Confirm that indicator light or arch light turns on.cWhen charging is over, pull out the power plug from the outlet, and pull out from FOMA terminal horizontally while pressing the release buttons on both sides of the connector.aInsert the connector of AC adapter horizontally to the accessory desktop holder, with the arrow mark side upward.bUnfold the AC adapters power plug and insert it into a 100V AC outlet.cJoin FOMA terminal units into basic style and insert it into the desktop holder.*Confirm that indicator light or arch light turns on.dAfter charging is completed, remove FOMA terminal from the desktop holder.✜ Operations for chargingWhen charging starts, a charge start alert sounds. While charging, the indicator light or arch light turns on and the battery icons on the display blinks. When charging is ended, a charge completion alert sounds.Charging using AC adapter100V AC outletConnectorRelease buttonExternal connection jackJack capPower plugAC adapterIndicator lightArch lightUsing desktop holder and AC adapter in combination for charging100V AC outletIndicator lightArch lightRelease buttonConnectorDesktop holderInsert at the back sideAC adapterPower plug

Navigation menu