Fujitsu FOMA-F905IBIZ PCS Licensed Transmitter User Manual F905i

Fujitsu Limited PCS Licensed Transmitter F905i

Contents

Users manual part 3

26 Before Using the HandsetF905i_E2kouSwinging display (YOKO-MOTION)With FOMA terminal open, rotate the display 90 degrees to the right or left to display Horizontal display.･You can activate 1Seg or Still camera by rotating. You can also answer a call by returning the display to vertical position. You can change in Turn-display option to set functions to be activated by rotating.→P348･On horizontal display, the display position of the guide area, etc. are different, but the same operations as those on vertical display can be performed.✔INFORMATION･Do not rotate the display with the FOMA terminal folded. May cause the display and around the keys to be scratched.･While one of the Submenu, New Task start menu or Switch Task menu is being displayed, swinging the display closes the menu.❖Using wide displayBy returning the display to horizontal position, the functions and/or data below can be displayed on 864 dots (horizontal) wide display.･Full Browser･i-αppli with a size exceeding 320 dots (horizontal)･i-motion, PDF data, Word, Excel, PowerPoint file with a size of QVGA (240×320)･1Seg (including Multi window)Display overviewThe current status can be checked by the icon appearing on the screen.a : Battery icon→P39b : Signal level icon→P39 : Out of service area→P39 : Self mode ON→P112 : In data transfer mode→P117, 292, 307c/ : In i-mode communication (connected to i-mode site)/(during packet communication)→P148d : In infrared communication→P307Infrared remote control function in operation→P310 : The total calls cost exceeds the limit.→P353*1e : Communication using handsfree-compatible device in progress→P54 : Speakerphone function in use→P45(blue)/ (red)/ / : Network in use→P390*1f : Positioning with GPS→P240 : FM broadcasting→P336(blue)/ (gray) : Location request setting with GPS/out of Permission period→P246g : Phonebook entry or schedule data has secret attribute→P82, 346When swung to the rightVertical displaya-ma-mo-zo-znHorizontal displayF905i.book Page 26 Friday, October 19, 2007 7:43 PM
27Before Using the HandsetF905i_E2kou*1hUnread Area Mail, unread message or MessageR&F status→P177, 199, 201, 206 : Unread Area Mail : Unread i-mode mail and SMS storage space is full on UIM : Unread i-mode mail and SMS storage space is full : SMS storage space is full on UIM : Unread i-mode mail and SMS exists : Unread i-mode mail exists : Unread SMS exists (red)/ (blue) : Unread MessageR storage space is full or unread MessageR exists(red)/ (green) : Unread MessageF storage space is full or unread MessageF exists*1iPushTalk status or storage status in i-mode Center→P68, 177, 199 : During PushTalk session : Downloading phonebook page on the network : i-mode mail and MessageR&F storage are full or one of these spaces is full and unreceived messages exist in Data Center/ / : i-mode mail or MessageR/F storage space is full in Data Center : Unreceived i-mode mail and MessageR/F exist in Data Center/ / : Unreceived i-mode mail, MessageR or MessageF exists in Data Center*1j : Displaying SSL page/executing SSL session with i-αppli or using i-αppli downloaded from SSL page→P149Displaying SSL/TLS page→P270 : Mail failed to Auto-send exists→P176 : Auto-send mail exists→P176 : Music&Video Channel program obtaining reservation exist→P321ki-αppli/i-αppliDX status→P213, 223 : During i-αppli operation (gray) : i-αppli stand-by display ON(orange) : i-αppli is being started from the i-αppli stand-by display : i-αppliDX is running(gray) : i-αppliDX stand-by display ON(orange) : i-αppli is being started from the i-αppliDX stand-by display*2l : Performing 1Seg recording reservation/1Seg recording. (only watching stopped)→P259, 265 : i-αppli Auto start failed→P222*2m : Inside OFFICEED area→P380n : New arrival→P33o : Silent mode ON→P91 : Personalized silent mode ON→P92p : Call alert volume OFF→P88 : Vibrator for voice call set ON→P89 : Call alert volume set OFF and vibrator for voice call set ON→P89q : In Public mode (Drive mode)→P57r/ : Answer machine set ON/recorded message full→P60*1s : Keypad dial lock ON→P113 : Side key hold ON→P119*1t/ / : Location request success/failure/end as unanswered→P245 : Personal data lock ON→P112/ : Music&Video Channel obtaining failure/success→P321/ : 1Seg recording reservation failure/success→P259*1u : Reading UIM→P34, 39(yellow key) : IC card lock ON→P235 : Individual IC card lock→P236v/*3 : Displaying available multi-cursor key in Focus mode→P33 : Lock on close ON→P119w : Alarm clock set ON→P340 : Performing 1Seg watching/recording reservation, schedule reminder set ON→P258, 342 : Schedule reminder, 1Seg watching/recording reservation and Alarm clock are all set ON→P258, 340, 342xUSB mode settings and microSD memory card status→P294, 300 : microSD memory card inserted during Communication mode (blue)/ (gray) : microSD memory card inserted or not during microSD mode (blue)/ (gray) : microSD memory card inserted or not during MTP modey : Connected to external device using USB cable→P65, 301*1z : Software update advance notice→P442 : Software update pre-specified→P443 : Update notification icon→P442/ : Auto-update of latest pattern definition failure/success→P445*1The current highest-priority item is displayed. These icons are listed in descending order of the priority from the top.*2On vertical display without stand-by display or on some wide display, a clock appears.*3On horizontal display, it appears below n New arrival.✔INFORMATION･On wide display, icons appear similarly to vertical display. Note that, depending on the function displayed, some or none of the icons may not appear.L03.fm Page 27 Tuesday, October 23, 2007 9:00 AM
28 Before Using the HandsetF905i_E2kou◆Task areaThe icon indicating the function (task) in progress appears in the task area. During Multiaccess or Multitasks, the icons show which functions are running.<Example> When activating Still camera during a voice call<Example> Displaying Word file during a voice call*When displaying Word, Excel or PowerPoint file on wide display, a task area appears similarly to vertical display.❖Icons indicated on the task area : Voice call : Redial : Received calls : Answer machine/Voice memo : Videophone call : Videophone using an external device : Call (switching) : Call (disconnecting) : PushTalk : FOMA terminal phonebook : Contact setting of Privacy mode : Kisekae Tool : Still camera : Movie camera : Bar code reader : i-mode : i-mode Bookmark/Go to location/Browser history/Screen memo/two-touch site : Mail/MessageR&F : Area Mail : Receiving i-mode mail : Inquiring for i-mode mail/SMS/ : Sent msg log/Received msg log : Chat mail : Receiving SMS : i-αppli : ToruCa : Position location of GPS : Location request of GPS : Notify location of GPS : Location history (GPS) : Full Browser : 1Seg : My Picture : Movie/i-motion : Chara-den : Melody (blue)/ (gray) : Accessing microSD memory card/Standing by for accessing : Activating Music&Video Channel : Music&Video Channel program obtaining : Music player : Sound recorder : My Document (PDF data) : Other (Word, Excel, PowerPoint file) : Adjusting volume by Multitask : Countdown timer : Alarm clock : Scheduler/schedule reminder ringing (including Notify start of 1Seg) : User information : Calculator : Notepad : Dictionaries : Accessing Data Center : Displaying synchronization log : Network services set/ : Calling or communicating packets via USB/Sending or receiving packets via USB : 64K data communication : Accessing external data/ : Updating software/Software update notified : Updating pattern definition/displaying version/ (gray) : Each function set or on holdVertical displayHorizontal displayTask areaWide displayTask areaF905i.book Page 28 Friday, October 19, 2007 7:43 PM
29Before Using the HandsetF905i_E2kou◆Guide areaOperations that can be executed by pressing m, t, g, p and a are displayed in the guide area. Displayed operations vary by the screen.Display locations and keys correspond as shown in the figure.･ on the guide area corresponds to multi-cursor keys k (It may be different depending on the function you are using or how the site or website is made).･When the display is placed in horizontal position, this is displayed at the left bottom of the display.･In wide display, press * to display a guide area; each pressing of this key switches guide area display/hide (except during 1Seg watching).◆List screenaWhen a list extends to multiple pages, the currently displayed page number and the total number of pages appear.bThe items can be selected by pressing the keypads corresponding to the displayed number (1-9). On vertical display, item can be selected also by pressing the displayed next key. : 0  : M : *  : Side key[▲] : #  : Side key[▼]cindicates that other selectable items exist above and below the item at the cursor position. Press j to move the cursor. When d is pressed on the last item of the page, the next page appears, when u is pressed on the first item of the page, the previous page appears. indicates that selectable items exist over the multiple pages. Press h to change the page. Some screens such as an icon selection screen cannot be switched.Sub-display overviewEven when FOMA terminal is folded, various informations can be checked on the sub-display.･Main displayed information are as follows.- Status display of voice call, videophone (including Chaku-moji and Voice messages in Voice Mail service), PushTalk, recorded message- Inquiring or receiving i-mode mail, SMS or MessageR/F- Status display of Position location of GPS, Location request, Notify location function- While watching 1Seg, playing video, playing melody, activating Music&Video Channel player, activating Music player or using microSD memory card- During Alarm clock, Schedule reminder (including Notify start of 1Seg) or Countdown timer sounding- Status display of packet communications, 64K data communication, via USB communication, infrared communication or iC transmission･In All lock, Omakase Lock, Side key hold, pressing side keys [▲▼], P or M shows a message indicating the lock is set, and after a period of time, the display is switched to the date/time display screen.･When the FOMA terminal is folded, the light on the sub-display turns on. When no operation is carried out for approximately 15 seconds, the light goes unlit; it goes lit again when one of side keys [▲▼], P or M is pressed.･When opening the FOMA terminal with information displayed on the sub-display, display disappears. During shooting a still image, recording movie, shooting stand-by or recording stand-by with Sound recorder, the status appears only when the FOMA terminal is open. While recording with Sound recorder, the status appears regardless of the status of the FOMA terminal.･By pressing P while watching/recording 1Seg, playing video, activating Music player or Music&Video Channel player, you can display date and time.Guide areaacbF905i.book Page 29 Friday, October 19, 2007 7:43 PM
30 Before Using the HandsetF905i_E2kou❖Icon list displayed on the sub-displaya : Battery iconb : Signal level icon : Out of service area : Self mode ON : In data transfer modec/ : In i-mode communication (connected to i-mode site)/(during packet communication)d : Silent mode ON : Personalized silent mode ON : Activating Music player : During 1Seg watchinge/ : Location request setting with GPS/Out of permission periodf : IC card lock ONg/ : i-mode mail and MessageR&F storage spaces are full in the Centerh/ : Auto-send mail exists/failed auto-send mail existsi : Missed calls/Recorded messages/Voice messages in Voice Mail service existj/ / : Unread Area mail exists/unread i-mode mail and SMS exist/storage space is fullk/ : Unread MessageR exists or unread MessageR storage space is full/ : Unread MessageF exists or unread MessageF storage space is full◆Switching display of sub-displayWhen missed calls, recorded messages, unread messages, unread MessageR&F or Voice messages in Voice Mail service in the Center exist, turn on the sub-display light and press side key [▼] to check the number of these items. While checking the number of items, if you press side key [▲], detail information appears for approx. 5 seconds (except for Voice messages in Voice Mail service).･Up to 10 detail info can be confirmed by pressing the side key [▼].<Example> Switching to detail information of missed calls 1Side key [▲] while confirming the number of items.The number of items, total number of items, receive date/time, and the caller information are scroll-displayed.Selecting functions from menu◆Menu screen and switching method❖Menu screenThe menu screen below is available.Kisekae menu : A menu that you can change the design using Kisekae tool.In addition to menus compatible with movies, AdvancedMode that is easy to view with large font and SimpleMenu are available. A Kisekae menu matched with the color of the FOMA terminal is set by default.･Some Kisekae menu changes the menu structure of its first layer according to usage frequency. In the Kisekae tool set by default, "ドコモダケ_F905i" in the "i-mode" folder is compatible with this function.･Some Kisekae menus, such as "ドコモダケ_F905i", are not compatible with English display when setting Select language to "英語".Basic menu : A basic menu that the menu structure and menu numbers are fixed.･Menu icons or background design can be changed by customizing Kisekae Tool or menu.→P98, 101･The font size of the menu changes synchronized with Kisekae Tool.Custom menu : A menu that menu items can be freely registered.→P347d j h i af e b c g k Side key [▲]L03.fm Page 30 Tuesday, October 23, 2007 10:38 AM
31Before Using the HandsetF905i_E2kou❖To switch the menu screen temporarilyIn each menu screen, you can temporarily switch to a different menu screen by the operations below. You can also set which menu to display when pressing m on the stand-by display.→P98*1Cannot be switched when Basic menu is set as Select startup menu.*2Cannot be switched when Kisekae menu or Custom menu is set as Select startup menu.❖Precautions on using Kisekae menuDepending on the type of Kisekae menu, the menu structure of the first layer may change according to usage frequency. Also, the number assigned to menu item (item number) may not be applicable to some menu items. In such a case, as operations cannot be performed as described in this manual, switch to the basic menu or reset (→P100) the operation logs of the menu.･When "ドコモダケ_F905i" is set for Kisekae menu, the structure of Basic menu can be temporarily restored also by selecting [Basic] in the menu of the first layer.◆Selecting a functionPress m in stand-by and select and execute the functions from the menu displayed.There are 2 ways. One method involves using the key corresponding to the menu items (Shortcut operation). In the other method, the multi-cursor key is used to select from among the menu items.･When any function is restricted by lock functions or no UIM in slot, icon appears or characters are displayed in a different color that the function is disabled. The display does not change for Kisekae menu or Basic menu on horizontal display. When a function is selected, the reason the function is nonexecutable, etc. appears.･On vertical display, function description about the menu item at the cursor position may appear depending on the type or level of the menu. And the setting may be displayed depending on the menu item.❖Selecting menu items by key (Shortcut operations)When numbers (item number) are assigned to menu items, a menu item can be selected by pressing the corresponding keypad (1-9, 0, *, #).･Press the item number displayed with the desired menu item.･Item numbers differ when SimpleMenu is set in Kisekae Tool.･Item number of the menu→P398 "Menu list"<Example> Selecting "Calculator"1me7e4tCustom menuKisekae menu Basic menup*1p*2m74F905i.book Page 31 Friday, October 19, 2007 7:43 PM
32 Before Using the HandsetF905i_E2kou❖Selecting menu items by multi-cursor key<Example> Selecting "Calculator"1mePlace the cursor on "Accessory", and g･If you press k to move the cursor, the color and/or design of the cursor position change. Moving by h may be unavailable depending on the menu.･When you set SimpleMenu for Kisekae menu, you can select menu also by placing the cursor and pressing r.2Place the cursor on "Calculator" and g❖To return to stand-by display or previous menuAfter selecting a menu item, you can return to the stand-by display or previous menu by pressing the keys below.f : Return to the stand-by display.c : Return to the previous menu. Depending on the menu, you can return to the previous menu also by pressing l.◆Selecting method of submenuWhen "MENU" is displayed at upper-left of the guide area, various operations can be performed with submenus.<Example> Selecting the redial submenu1On the redial list screen, mePress a key for the submenu item number･You can also select an item by placing the cursor on and pressing g or r.･Item numbers of the submenu with the same functions may vary by the operating screen.･Pressing m or c closes the submenu.◆Operating procedure of each item❖Selection of an item1Press the key for the item number.･You can also select an item by placing the cursor on it and pressing g.･Depending on the function, you can check vibration pattern of the vibrator, color or lighting pattern of Light alert, the color scheme of screen settings or brightness of the display by placing the cursor on an item.❖Pulldown menu operation1Place the cursor on the item to set and gePress a key for the item number･You can also select an item by placing the cursor on it and pressing g.❖Check box operation1Press a key for the item number.･You can also select an item by placing the cursor on it and pressing g.･Pressing key for the item number or pressing g after placing the cursor, the status of check box switches (Select) and (Cancel).･For some functions, you can select or cancel all items by pressing m.Basic menuCursor positionKisekae menumThere are menu items in lower levelsPulldown menuF905i.book Page 32 Friday, October 19, 2007 7:43 PM
33Before Using the HandsetF905i_E2kou❖Confirmation screen operationWhile deleting or setting saved information, a confirmation screen may appear asking you to perform a function.<Example> Deleting Phonebook data (1 item)1Place the cursor on "Yes" or "No" and g.･For some functions, items other than "Yes" or "No" may appear.◆Displaying information quickly <Focus mode>When g is pressed on the stand-by display with newly arrived information (icon) being displayed on the stand-by display or with Info/calendar layout set and displayed, the display is set to Focus mode that allows to quickly display the related information.<Example> Displaying newly arrived information1gePlace the cursor on an icon and g･A screen matched for the selected icon appears.(Missed calls) : Received call list appears. With 2in1 ON in Dual mode, appears when there is a missed call only to Number B and appears when there are missed calls to both Number A and B.(Recorded messages) : The recorded message list appears.(Voice messages in Voice Mail service) : A confirmation screen of message play appears. With 2in1 ON in Dual mode, appears when there is a voice message only to Number B and appears when there are voice messages to both Number A and B.(Unread messages) : The folder list of Inbox appears. (Unread ToruCa) : The ToruCa list of the folder containing the latest unread ToruCa appears.･You can perform the same operations when the next icon appears.- : Connect to external device using USB cable- / : Software update advance notice/notification- / : Auto-update of latest pattern definition success/failure- / / : Location request success/failure/end as unanswered- / : Music&Video Channel program obtaining success/failure- / : 1Seg recording reservation failure/successCanceling Focus mode : c or f✔INFORMATION･When placing the cursor on the icon for newly arrived information and press and hold c for 1 second or more, the icon disappears temporarily. For a voice message icon of Voice Mail service, a confirmation screen appears asking you to delete the display. Select "Yes" to delete the display. It reappears when the number of items is changed by accumulating new information or viewing existing information.･In Focus mode, you cannot display the menu by pressing m.Selecting a function from menu on sub-displayYou can select 5 functions of MusicPlayer/End MusicPlayer, Lock/Unlock IC card, Silent mode ON/OFF, Check new msg, Quick light.<Example> Performing i-mode inquiry1While sub-display light is ON, PeUsing side keys [▲▼], place the cursor on "Check new msg" and M･During menu display, press P to return to date/time display.･Authentication is required when "Unlock IC card" is selected.gAn icon at the cursor position is surrounded with a red frame.The direction is indicated that it can be moved to by using multi-cursor key.CursorF905i.book Page 33 Friday, October 19, 2007 7:43 PM
34 Before Using the HandsetF905i_E2kouUsing UIM (FOMA card)UIM (FOMA card) is a card for storing user information such as phone numbers.･If a UIM has been inserted incorrectly or if there is a problem with the UIM, you cannot make/receive a call or send/receive a mail.･For details on handling UIM, see the UIM manual.◆Attaching/removing UIM･After turning the power OFF, fold FOMA terminal and hold it with your hand.･Take care not to touch or scratch the IC portion.･Attaching/removing back cover and battery pack→P35✔INFORMATION･Forcing the UIM into or out of FOMA terminal may damage UIM or the tray.･If the tray is removed, press it straight along the guide rail inside the UIM slot with the UIM left detached.◆Security code of UIMTwo security codes, "PIN code" and "PIN2 code", are set for the UIM.You can change the security codes by yourself.→P108◆UIM operation restrictionFOMA terminal is provided with the UIM operation restriction for protecting your or copyright data or files.･When files or data are downloaded from websites or data attached to mails are obtained to your FOMA terminal with the UIM card equipped, the UIM operation restriction is automatically set to these data or files.･With UIM replaced or no UIM inserted, data or files with the UIM operation restriction set cannot be displayed or played. For i-αppli with the UIM operation restriction set, no functions except deletion are available.･Data or files with the UIM operation restriction set cannot be transferred over infrared communication/iC transmission or copied/moved to microSD memory card.･Restricted data types are as follows : - Videophone call message, Movie memo- i-mode mail attachment files (except ToruCa), images inserted to Deco-mail or signature, MessageR&F, mail template containing data subject to operation restriction- Screen memo-i-αppli (including i-αppli stand-by display)- Image of ToruCa (Details)- Images (including GIF animations, Flash graphics and images downloaded from Data Center), i-motion, data compatible with contents transfer, melodies, PDF data, Chara-den, Word/Excel/PowerPoint files- Kisekae Tool-Chaku-uta®/Chaku-uta full®- Program of Music&Video ChannelaHolding the tab, pull out the tray until it clicks.TrayTab■ AttachingbPut UIM with the IC side upward on the tray in the direction shown in the figure.ICCorner cutUIMcPush the tray fully until it stops.aHolding the tab, pull out the tray until it clicks and carefully remove UIM.■ RemovingUIM slotTabF905i.book Page 34 Friday, October 19, 2007 7:43 PM
35Before Using the HandsetF905i_E2kou*"Chaku-uta" is a registered trademark of Sony Music Entertainment (Japan) Inc.✔INFORMATION･When data, subject to the UIM operation restriction is set as the stand-by display, incoming/outgoing image, ring alert, etc., replacing the UIM with another one or using FOMA terminal without the UIM inserted causes the sound, image and other settings to reset to the default values. In this case, the sound or image actually generated or appears may be different from those set. If the UIM used when downloading the data is inserted, the data operation restriction is canceled and the original settings are restored (When data has been used for Set random image, the settings may be canceled).･The UIM operation restriction is not enabled for data obtained via infrared communication, iC transmission, microSD memory card or DoCoMo keitai datalink or still images/movies taken with the built-in camera.･The settings below are saved to UIM. When UIM is replaced, the set contents saved in the inserted UIM are enabled.- My phone number- SMS settings (except "SMS report request")- DoCoMo Cert/User Certificate of Manage certificate- Select language, UIM, PLMN setting◆Functional differences in UIM typesWhen using UIM (Blue) in FOMA terminal, note that it differs in the items listed below from UIM (Green/White).WORLD WINGWORLD WING is DoCoMo's FOMA international roaming service that you can make/receive calls from/to the same phone number overseas by inserting the UIM (green/white) to a FOMA terminal or a mobile for overseas use (W-CDMA or GSM communication method) compatible with the service.*If you subscribed to FOMA service on or after September 1, 2005, separate subscription is not required to use WORLD WING. Note that, if you declined to use WORLD WING at subscription to FOMA service or canceled it, you need subscription.*If you subscribed to FOMA service on or before August 31, 2005, but not to WORLD WING, separate subscription is required to use WORLD WING.*There are some charging plans unavailable.*If UIM (Green/White) is misplaced or stolen overseas, immediately contact DoCoMo and request for suspension of usage. Please refer to the phone number for "General Inquiries" on the back of this manual for contact information. Be careful that you are charged also for calls and/or communications, if any, occurring after misplacement or stealage.Attaching/removing battery pack･After turning the power OFF, fold FOMA terminal and hold it with your hand.･Removing the battery pack may cause reservation of Software update to be canceled. When the date and time is set with Auto time adjust set to "OFF" in Date & time, removing the battery pack may delete the date and time.Item UIM (Blue)UIM (Green/White)PageNumber of savable digits of phone numbers in UIM phonebookUp to 20 digitsUp to 26 digitsP76User certificate download to use FirstPassUnavailable Available P163WORLD WING serviceUnavailable Available P388Service NumbersUnavailable Available P375Press here with your thumbBack Cover■ AttachingaRemove the back cover by sliding it about 2 mm in the direction of the arrow while pressing it with your thumb.F905i.book Page 35 Friday, October 19, 2007 7:43 PM
36 Before Using the HandsetF905i_E2kou✔INFORMATION･Forcing the battery pack into FOMA terminal may damage the FOMA terminal jack.･FOMA terminal or back cover may be damaged if you attach or remove the battery pack by a method except the procedures above or if you press too hard.❖For better battery pack performance･Do not charge the battery for an extended period (several days) with the FOMA terminal turned ON.After charging has completed with FOMA terminal turned ON, the power is supplied to the terminal from the battery pack. If FOMA terminal is left in that state for a long time, the battery pack may run out causing the low battery alert to sound after using only a short period of time. In such a case, remove FOMA terminal from the AC adapter, desktop holder or DC adapter and then reconnect it and charge the battery again.･To promote environmental conservation, return your used battery pack to NTT DoCoMo sales outlets, our corporate agencies or the shops that collect used battery in your community.Charging the FOMA terminalThe battery pack does not have a full charge at time of purchase. Use AC/DC adapter for FOMA terminal to charge the battery before using FOMA terminal.･To get the maximum performance from F905i, use battery pack F10.･For handling the battery pack F10, see the battery pack manual.❖Charging times (approximate)The times below are the times for charging an empty battery pack with F905i's power switched OFF. Charging with the terminal ON or under low temperature requires longer time.❖Operation times on full charge (approximate)The times below vary by the charging method and operating environment.･Continuous call time indicates the approximate time that the phone can send or receive radio waves normally.Concave partBattery PackConvex partbWith the label side of the battery pack face up, align the convex part of the battery pack with the concave part of FOMA terminal, insert the battery pack in the direction of a and press it in the direction of b until it fits.cBring the 5 tabs of the back cover to meet the cuts in FOMA terminal. Slide in the direction of d to fit in while pressing in the direction of c so that no gap is generated between FOMA terminal and the back cover.Back cover■ RemovingTabaPerform Step a in Attaching battery pack.bHold and raise the battery pack tab in the direction shown by the arrow to remove the battery pack.AC adapterApprox.150 min.DC adapterApprox.150 min.Continuous stand-by timeFOMA/3GStationary (Auto) : Approx. 505 HMoving (Auto) : Approx. 330 HMoving (3G static) : Approx. 360 HGSMStationary (Auto) : Approx. 300 HContinuous call timeFOMA/3GVoice call : Approx. 190 min.Videophone call : Approx. 110 min.GSMApprox. 200 min1Seg watching timeApprox. 260 minF905i.book Page 36 Friday, October 19, 2007 7:43 PM
37Before Using the HandsetF905i_E2kou･Continuous stand-by time indicates the approximate time that the phone can receive radio waves normally with F905i closed. Call, communication or stand-by times may be about half or 1Seg watching time may be shortened depending on factors such as the battery pack charging condition, function settings, operating environment such as ambient temperature, and signal condition in the area of use (whether the signal is weak or absent). Call, communication or stand-by times are reduced by performing i-mode communication. And, even with no voice calls or i-mode communications made, the continuous call and continuous stand-by times are reduced by making PushTalk session, creating i-mode mail, activating downloaded i-αppli, using i-αppli stand-by display, performing data communication or multiaccess, using camera, playing movie/i-motion, obtaining or playing Music&Video Channel program, playing music with Music player, activating or recording of 1Seg, or doing other operations.❖Battery pack life･The battery pack is a consumable part. Each time it is charged, time available with each charging reduces.･When a time available with each charging is reduced to about a half from that of a new battery, replacement of the battery is recommended because it is near the end of life. The battery pack may swell out as it comes to near the end of its lifetime depending on the usage conditions, but it is not a problem.･The battery pack's life may be reduced by using i-αppli or videophone or watching 1Seg while charging.❖Battery charge･For details, see the operation manuals for FOMA AC Adapter 01/02 (optional), FOMA AC Adapter 01 for Global use (optional) or FOMA DC Adapter01/02 (optional).･FOMA AC Adapter 01 is applicable only to 100V AC. Though FOMA AC Adapter 02 and FOMA AC Adapter 01 for Global use is applicable to 100-240V AC.･AC Adaptor has a plug dedicated to 100V AC (for domestic use). When using the AC adapter in the range of AC 100V and 240V overseas, a conversion plug adapter applicable to the country you are staying is required. Do not charge the battery using a transformer for overseas travel.✔INFORMATION･Some i-αppli remains operating even when FOMA terminal is folded, consuming power. In that case, the call, communication or stand-by time may be reduced.･During talking or communications, charging may not finish. Charging may not complete if you start battery charging while playing movie/i-motion, obtaining Music&Video Channel program, activating Music &Video Channel player or Music player, running i-αppli. In such a case, it is recommended to end the operation, and then charge the battery.･The charging may not be completed depending on the settings of Display light or charging method, such as charging the battery with the FOMA terminal open when Normal use is set to "Always" in Display light time of Display light. In such a case, it is recommended to charge the battery with the FOMA terminal folded.･It is normal for FOMA terminal, battery pack, desktop holder and AC adapter, DC adapter to become warm while charging. If you use the videophone or if you transmit/receive packets or 64K data while charging the battery, the charging may not finish normally because of temperature rise in FOMA terminal. In that case, wait until the temperature falls down and try again.◆ChargingWhen using optional FOMA AC Adapter, FOMA DC Adapter, Desktop Holder, read the related operation manuals beforehand.･The battery pack cannot be charged without an adapter. When charging the battery pack, attach it to FOMA terminal.■Using desktop holder and AC adapter for chargingaInsert the AC adapter to the desktop holder, with the arrow on the AC adapter's connector facing upward.bUnfold the AC adapter's power plug and insert it into a 100V AC outlet.cAlign FOMA terminal with the desktop holder's charging terminal (a), and insert FOMA terminal in the direction of the arrow (b) until it clicks.･Before mounting FOMA terminal onto the desktop holder, fold it and close the terminal cap.dWhen charging is over, lift FOMA terminal (c) while holding the desktop holder and remove the terminal by pulling it in the direction shown by arrow (d).AC adapter100V AC outletPower plugConnectorRelease buttonDesktop holderCharging jackJack capLampbaF905i.book Page 37 Friday, October 19, 2007 7:43 PM
38 Before Using the HandsetF905i_E2kou■Charging with AC adapter or DC adapteraOpen terminal cap (a) of FOMA terminal, hold the connector horizontally with the arrow facing upward and insert it to terminal. (b)bUnfold the AC adapter's power plug and insert it into a 100V AC outlet.Insert the DC adapter cigarette lighter plug into the vehicle's cigarette lighter socket.cAfter charging has completed, disconnect the AC adapter from the outlet or the cigarette lighter plug from the cigarette lighter socket, and press the release buttons on both sides of the connector and remove the connector horizontally from FOMA terminal.✔INFORMATION･Insertion or removal of the AC and DC adapter connectors should be done slowly and carefully so that they are not given excessive force. When disconnecting the connector, pull it straight while pressing the release button. Applying an excessive force to disconnect the connector may give damage to it.･When FOMA terminal is not used or you are leaving the car, disconnect the cigarette lighter plug of the DC adapter from the cigarette lighter socket and disconnect the DC adapter connector from FOMA terminal.･The fuse (2A) of the DC adapter is a consumable part. Contact your nearest automotive supply store for a replacement.❖Operations and precautions for chargingWhen charging starts, a charge start alert sounds, light turns ON and the battery icon on the display or sub-display blinks. When charging is over, a charge completion alert sounds, the light turns off and the battery icon stops blinking.･When resuming the battery charging, the light turns on in red. In some environments, the light may not light immediately when charging starts; this is normal and not a malfunction. However, if the light fails to light after a while, disconnect FOMA terminal from the AC adapter, desktop holder or DC adapter then connect it again to start charging. Contact the sales outlet such as DoCoMo Shop if the light fails to light for a while after charging starts.･If the light is used for mail reception, camera shooting, etc. during charging, the light turns to a different color, but it is lit in red soon.When the light blinks while charging in cases except these reasons→P431 "Troubleshooting"･When attaching the fully charged battery pack to the FOMA terminal and connecting it to the AC adapter, desktop holder or DC adapter, the light may turn on for a moment and turn off. This is normal and not a malfunction.･During a call, communication or PushTalk session, in Silent mode or Public mode or with Charge alert "OFF", the charge alert does not sound at start or completion of charge.dcab<AC adapter>ConnectorRelease buttonJack capCharging jackAC adapterPower plug100V AC outletLamp<DC adapter>Cigarette lighter plugCigarette lighter socketDC adapter Release buttonJack capCharging jackConnectorabLampF905i.book Page 38 Friday, October 19, 2007 7:43 PM
39Before Using the HandsetF905i_E2kouRemaining battery levelChecking remaining battery levelA battery icon appearing on the top of the display shows an approximate remaining battery level.(Battery level 3) : Ample charge(Battery level 2) : Low charge.(Battery level 1) : Battery level very low. Charging required･The battery icon set by default varies by the color of the FOMA terminal.･When FOMA terminal is folded, the remaining battery level can be checked on the sub-display.❖When battery is almost exhaustedA message indicating low battery appears on the display. Pressing any one of g, c, f keys deletes the message temporarily. After a period of time, a battery alarm sounds from the speaker and all icons on the top of the display start blinking. The power is turned off after approximately 1 minute. These operations stop when charging starts; press f to immediately stop the battery alarm.･During a call, the message remains displayed and the battery alarm keeps sounding from the earpiece. After approximately 20 seconds, the call is terminated, the battery alarm sounds from the speaker and all icons on the top of the display blink. ･With the FOMA terminal folded, the sub-display shows "Low battery".◆Checking remaining battery level by sound and display <Battery level>1me[Settings & NW services]e775The battery level appears and the keypad sound (→P90) is emitted depending on the battery level. After a while, the screen returns to the menu list.Power ON/OFFTurning power ON/OFF❖Turning power ON1f (2 sec. or more)The wake-up screen appears and the stand-by display appears. appears at the bottom of the display while reading UIM.･A signal level icon appearing in the top of the display shows the approximate received signal level.･The battery icon set by default varies by the color of the FOMA terminal.･With the FOMA terminal folded, the reception level can be confirmed on the sub-display.❖Turning power OFF1f (2 sec. or more)◆Operations to perform after turning the power ON for the first timeWhen turning the power ON for the first time, operate in the order of "AdvancedMode setting" → "Initial setting". The settings made can be changed later.･When initialization is finished, a confirmation screen of software update function appears. Press g to display the stand-by screen.Battery icon"Three pips" "Two pips" "One pip"(Battery level 3) (Battery level 2) (Battery level 1)Stand-by displaySignal level iconIconReceived signal levelOutside the service area and where radio waves are hard to reachStrong WeakF905i.book Page 39 Friday, October 19, 2007 7:43 PM
40 Before Using the HandsetF905i_E2kou❖AdvancedMode setting1"Yes" or "No" on the confirmation screen.･When selecting "Yes", "拡大メニュー (AdvancedMode)" of Kisekae Tool is set.→P410If you cancel the confirmation screen by pressing c or f, the confirmation screen reappears when the power is turned ON the next time.❖Default settingMENU [Settings & NW services] 779･Always set Password and Request permit/deny. When p or c, f is pressed before setting terminal security code or Request permit/deny, a confirmation screen appears asking you to exit. If you exit by selecting "Yes", this confirmation screen reappears when the power is turned ON the next time.1Set the required items on the initial setting screenepDate & time : Set the date and time.→P40Password : Change the terminal security code, after performing authentication.→P107Fingerprint : After performing authentication, register a fingerprint to be used for authentication.→P109Keypad sound : Set a confirmation sound to be generated when a key is pressed.→P90Text size : Specify size of characters for Phonebook or mail.→P103Request permit/deny : Set if you provide location information after performing authentication. To permit Location request only in a specified period of time, make settings to Permission period of Request permit/deny.→P245✔INFORMATION･When turning FOMA terminal ON, do not touch the fingerprint sensor with fingers before the stand-by display appears.･When the UIM is replaced, authentication is required after turning on the FOMA terminal. When authentication has succeeded, the stand-by display appears. If an incorrect terminal security code is entered 5 times consecutively or if authentication has failed 5 times consecutively when Fingerprint access is "ON", the power is automatically turned OFF (the power can be turned ON again).･If no operations are carried out for approximately 5 minutes with the FOMA terminal open, the display is automatically deactivated (power saving mode). The same situation occurs during voice call. The display light is turned on again if there is any operation or incoming call.Select languageSwitching to English1me[Settings & NW services]e273e1 or 2✔INFORMATION･The setting of Select language are saved to UIM. When a UIM is replaced, the setting switches to that saved in the inserted UIM.･Even if this setting is set to "English", the displayed menu may not be switched to English depending on the Kisekae Tool. Note that, when a Kisekae Tool in "Preinstalled" folder is set, a menu dedicated to "English" appears.Date & timeSetting date and timeYou can set so that the time or time difference is automatically corrected or directly enter the date and time. With automatic correction set, the time is corrected when receiving the time information from the DoCoMo's network in Japan or the time difference correction information from the telecommunications carrier used overseas.1me[Settings & NW services]e721eSet the required itemsepAuto time adjust : Set if you automatically correct time.･When "ON", Offset can be set.･When "OFF", set the date and time. Time zone and Summer time may also be set.Offset : When "+", the displayed time is always set forward the specified period of time from the corrected time. When "-", the displayed time is always set back the specified period of time from the corrected time.Date : The date can be entered up between January 1, 2000 and December 31, 2050.Time : Enter the time in the 24-hour format.Time zone : When moving to a place with time difference, set the time zone without changing the date and time settings.･Time difference from the previously set time zone is calculated and displayed.･Set "GMT+09:00" in Japan.F905i.book Page 40 Friday, October 19, 2007 7:43 PM
41Before Using the HandsetF905i_E2kouSummer time : When "ON", the displayed time is set forward one hour from the specified time.✔INFORMATION･With Auto time adjust set to "ON", the time or time difference is corrected when FOMA terminal is turned ON or at other timings. With no UIM inserted or for some signal conditions, the time is not corrected. During execution of certain i-αppli, time correction may be disabled.･Even when Auto time adjust is set to "ON", the corrected time may have an error of several seconds. Time difference correction may not be performed for some network of the telecommunications carrier used overseas.･When time correction is made overseas with Auto time adjust set to "ON", a message to that effect appears. After time is corrected with Auto time adjust, times displayed for call histories and sent messages are local times.･With Auto time adjust and Two time zone clocks set to "ON", two time zone clocks appear in 24 hour when time correction information is received from a network of the telecommunications carrier used overseas.･After setting the date and time with Auto time adjust set to "OFF", removing the battery pack or leaving it exhausted for a long time may cause the date and time to be deleted. In this case, set the date and time again after charging the battery.･If correction has never been performed and date and time are displayed with "--" or "?", clocks or Flash graphics using the date and time information do not appear correctly. The functions below are not available : - SSL session (authentication)- Certificate download- Message search (With scheduler)- Downloading Chaku-uta full® with replay restriction set for copyright protection or downloading and playing i-motion.-i-αppliDX, i-αppli Auto start- Playing the program that program setting, obtaining or playing restrictions of Music&Video Channel is set.- Playing WMA files with replay restriction under copyright protection- Request permit/deny (GPS)- Alarm clock, Scheduler (including data transmission of schedule and displaying schedule data)- Timed theme, Programed activation, Update, Auto power ON, Auto power OFF, Software update- Watching/recording reservation of 1Seg, playing Uta-hodai, updating replay expiration, setting ring tone･If automatic correction of date and time has never been performed and date and time are displayed with "--" or "?", the functions below do not record the date and time, in stead display them as "----/--/--" or "----------------". A segmental number furthermore (number to segmentalize) may be appended.- Date and time of sent message, unsent message, and mail logs, date and time of saving created message template- Date and time of saving downloaded data or file- Date and time of i-αppli download- Received calls, Redial, Recorded messages/Voice memo- Date and time in the file name of still images, movies, sound files or data read with Bar code reader- Reception date and time of ToruCa, Location history (GPS)- Replay expiration of detail information of Uta-hodaiCaller ID notificationNotifying your phone number to the other partyYou can set FOMA terminal to display your number (Caller ID) on the other party's terminal when making a voice call, videophone call or PushTalk call.･For details, see "Mobile Phone User's Guide [Network Services]".･Caller ID is your important information. Carefully consider whether you want to include caller ID information when making a call.･The caller ID is displayed only when the phone of the other party is a digital mobile phone, etc. enabled to display the caller ID.･Setting operations for this function is disabled from a location out of service area.1me[Settings & NW services]e8411･Press m[Settings & NW services]8412 and select "Yes" to check the current settings.21 or 2❖Priority of caller ID notificationThere are multiple methods to notify your phone number to the other party. If you set or perform these methods simultaneously, the caller ID operations are performed with the priorities below. The displayed setting and actual Notify/Not notify may differ.aWhen whether to notify a caller ID in Call option for the dialing is set→P51, 68bWhen "186"/"184" is prefixed to a phone number→P50cCaller ID settings of Phonebook (for PushTalk, dialing 1 party)→P81dActivate/Deactivate of Caller ID notification✔INFORMATION･If an announcement of requesting caller ID is heard when making a call, make a call again after setting your caller ID to be notified.F905i.book Page 41 Friday, October 19, 2007 7:43 PM
42 Before Using the HandsetF905i_E2kouUser informationChecking your own phone numberMENU [Phonebook & Logs] 9You can check your phone number (My phone number), Name, Mail address, etc.1me[User information]Check during a call, etc. : s0✔INFORMATION･For details of how to check i-mode mail address, see "Mobile Phone Users Guide [i-mode]".･When 2in1 is ON in Dual mode, you can press a to switch User information between Number A and B.･With 2in1 on, when replacing the UIM (2in1 subscriber to 2in1 subscriber), set 2in1 to OFF then set it to ON again to obtain a correct Number B, or obtain Number B from User information.→P350Also, when replacing the UIM (2in1 subscriber to 2in1 non-subscriber), set 2in1 to OFF to update to the new user information.→P378F905i.book Page 42 Friday, October 19, 2007 7:43 PM
449Appendix/External Devices/Troubleshooting 449F905i_E2kou◆Declaration of ConformityThe product "FOMA F905i" is declared to conform with the essential requirements of European Union Directive 1999/5/EC Radio and Telecommunications Terminal Equipment Directive 3.1(a), 3.1(b) and 3.2. The Declaration of Conformity can be found on http://www.fmworld.net/product/phone/doc/.This mobile phone complies with the EU requirements for exposure to radio waves.Your mobile phone is a radio transceiver, designed and manufactured not to exceed the SAR* limits**for exposure to radio-frequency(RF) energy, which SAR*value, when tested for compliance against the standard was 0.891W/Kg. While there may be differences between the SAR* levels of various phones and at various positions, they all meet*** the EU requirements for RF exposure.* The exposure standard for mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR.** The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/Kg) averaged over ten grams of tissue, recommended by The Council of the European Union. The limit incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements.*** Tests for SAR have been conducted using standard operation positions with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a base station antenna, the lower the power output.◆Federal Communications Commission (FCC) Notice･This device complies with part 15 of the FCC rules.Operation is subject to the following two conditions : athis device may not cause harmful interference, andbthis device must accept any interference received, including interference that may cause undesired operation.･Changes or modifications made in or to the radio phone, not expressly approved by the manufacturer, will void the user’s authority to operate the equipment.◆Industry Canada (IC) Notice･Operation is subject to the following two conditions : athis device may not cause interference, andbthis device must accept any interference, including interference that may cause undesired operation of the device.◆FCC and IC RF Exposure InformationThis model phone meets the U.S. Government’s and Canadian Government’s requirements for exposure to radio waves.This model phone contains a radio transmitter and receiver. This model phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy as set by the FCC of the U.S. Government and IC of the Canadian Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies.The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate (SAR). The SAR limit set by the FCC and IC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions as accepted by the FCC and IC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output level of the phone.Before a phone model is available for sale to the public, it must be tested and certified to prove to the FCC and IC that it does not exceed the limit established by the U.S. and Canadian government-adopted requirement for safe exposure. The tests are performed on position and locations (for example, at the ear and worn on the body) as required by FCC and IC for each model. The highest SAR value for this model phone as reported to the FCC and IC, when tested for use at the ear, is 0.278 W/kg, and when worn on the body, is 0.373 W/kg. (Body-worn measurements differ among phone models, depending upon available accessories and FCC and IC requirements).While there may be differences between the SAR levels of various phones and at various positions, they all meet the U.S. and Canadian government requirements.L026.fm Page 449 Friday, December 7, 2007 9:56 AM
450 Appendix/External Devices/TroubleshootingF905i_E2kouThe FCC and IC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC and IC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Equipment Authorization Search section at http://www.fcc.gov/oet/ (please search on FCC ID VQK-FOMA-F905IBIZ).For body worn operation, this phone has been tested and meets the FCC and IC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and which positions the handset at a minimum distance of 1.5 cm from the body.*In the United States and Canada, the SAR limit for wireless mobile phones used by the general public is 1.6 Watts/kg (W/kg), averaged over one gram of tissue. SAR values may vary depending upon national reporting requirements and the network band.◆Important Safety InformationAIRCRAFTSwitch off your wireless device when boarding an aircraft or whenever you are instructed to do so by airline staff. If your device offers flight mode or similar feature consult airline staff as to whether it can be used on board.DRIVINGFull attention should be given to driving at all times and local laws and regulations restricting the use of wireless devices while driving must be observed.HOSPITALSMobile phones should be switched off wherever you are requested to do so in hospitals, clinics or health care facilities. These requests are designed to prevent possible interference with sensitive medical equipment.PETROL STATIONSObey all posted signs with respect to the use of wireless devices or other radio equipment in locations with flammable material and chemicals. Switch off your wireless device whenever you are instructed to do so by authorized staff.INTERFERENCECare must be taken when using the phone in close proximity to personal medical devices, such as pacemakers and hearing aids.PacemakersPacemaker manufacturers recommend that a minimum separation of 15 cm be maintained between a mobile phone and a pace maker to avoid potential interference with the pacemaker. To achieve this use the phone on the opposite ear to your pacemaker and does not carry it in a breast pocket.Hearing AidsSome digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.For other Medical Devices : Please consult your physician and the device manufacturer to determine if operation of your phone may interfere with the operation of your medical device.Export Administration Regulations of Japan and the U.S.This product and its accessories are under coverage of the Export Administration Regulations ("Foreign Exchange and Foreign Trade Control Laws" and the related laws and regulations) of Japan and Export Administration Regulations or the U.S. When exporting or reexporting this product and its accessories, take necessary procedures on your responsibility and expense. For details, contact Ministry of Economy, Trade and Industry of Japan or US Department of Commerce.L026.fm Page 450 Tuesday, December 4, 2007 3:01 PM

Navigation menu