Fujitsu Stylistic St4000P Users Manual Alb_UG

STYLISTIC ST4000P Alb_UG-Passive-B

2015-01-25

: Fujitsu Fujitsu-Stylistic-St4000P-Users-Manual-218721 fujitsu-stylistic-st4000p-users-manual-218721 fujitsu pdf

Open the PDF directly: View PDF .
Page Count: 74

Fujitsu PC Corporation has made every effort to ensure

the accuracy and completeness of this document;

however, because ongoing development efforts are made

to continually improve the capabilities of our products,

we cannot guarantee the accuracy of the contents of this

document. We disclaim liability for errors, omissions, or

future changes herein.

Fujitsu and the Fujitsu logo are registered trademarks of

Fujitsu Limited; Stylistic is a registered trademark of

Fujitsu PC Corporation.

Kensington and MicroSaver are registered trademarks of

the Kensington Technology Group.

Microsoft is a registered trademark of Microsoft

Corporation. Windows 2000 Professional and Windows

XP Professional are trademarks of Microsoft

Corporation.

PCMCIA and CardBus are registered trademarks of the

Personal Computer Memory Card International

Association.

Intel, Pentium, and SpeedStep are registered trademarks

of Intel Corporation.

Wi-Fi is a trademark of the Wireless Ethernet

Compatibility Alliance (WECA).

All other products are trademarks or registered

trademarks of their respective companies.

reserved. No part of this publication may be copied,

reproduced, or translated, without the prior written

consent of Fujitsu PC Corporation. No part of this

publication may be stored or transmitted in any

electronic form without the prior consent of Fujitsu PC

Corporation

FPC58-0714-02

Note: For more detailed information about the FCC rules and their applicability to the Stylistic

ST4000P Series pen tablet PC, refer to Chapter 5 of this document.

DECLARATION OF CONFORMITY

according to FCC Part 15

Responsible Party Name: Fujitsu PC Corporation

Address: 5200 Patrick Henry Drive

Santa Clara, CA 95054

Telephone: 408-982-9500

Declares that product: Model Series: Stylistic® ST4000P

Complies with Part 15 of the FCC Rules

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and, (2) This device must accept any interference

received, including interference that may cause undesired operation.

Alb_UG.book Page i Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series - User’s Guide

Alb_UG.book Page ii Friday, November 1, 2002 4:22 PM

Table of Contents

PREFACE

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . v

Fujitsu Contact Information . . . . . . . . . . . . . . . . . v

Warranty Information . . . . . . . . . . . . . . . . . . . . . v

GETTING STARTED

WITH YOUR TABLET PC

In-box Items for the Stylistic

ST4000P Series pen tablet PC . . . . . . . . . . . . . 1

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . 2

Stylistic pen tablet PC Features. . . . . . . . . . . . . . . 3

Status Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Application Buttons . . . . . . . . . . . . . . . . . . . . . . 10

Navigation Buttons. . . . . . . . . . . . . . . . . . . . . . . 12

Tertiary Functions of Application

and Navigation Buttons. . . . . . . . . . . . . . . . . 13

Connectors and Peripheral Interfaces . . . . . . . . . 14

USING YOUR STYLISTIC

ST4000P TABLET PC

System States. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Powering Up the pen tablet PC . . . . . . . . . . . . . 20

Shutting Down the System. . . . . . . . . . . . . . . . . 20

Suspending System Operation . . . . . . . . . . . . . . 20

Resuming System Operation . . . . . . . . . . . . . . . 22

Using the Pen. . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installing a Pen Tether . . . . . . . . . . . . . . . . . . . . 22

Calibrating the pen. . . . . . . . . . . . . . . . . . . . . . . 23

Using Hovering Mode . . . . . . . . . . . . . . . . . . . . 23

Charging the Battery . . . . . . . . . . . . . . . . . . . . . 23

Removing and Installing the Battery. . . . . . . . . . 24

Tips for Conserving Battery Power . . . . . . . . . . . 24

Modem Connection . . . . . . . . . . . . . . . . . . . . . 25

PC Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Removing and Installing Memory Modules . . . . 25

CARE AND MAINTENANCE

Protecting the Display Screen. . . . . . . . . . . . . . . 29

Storing the pen tablet PC. . . . . . . . . . . . . . . . . . 30

Avoiding Overheating . . . . . . . . . . . . . . . . . . . . 30

Cleaning the Display Screen. . . . . . . . . . . . . . . . 30

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 30

SPECIFICATIONS

Stylistic ST4000P Hardware Specifications . . . . . 35

AGENCY NOTICES

Regulatory Information

Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

APPENDIX

Wireless LAN User’s Guide

Wireless LAN User’s Guide . . . . . . . . . . . . . . . . 45

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 55

About IP Addresses . . . . . . . . . . . . . . . . . . . . . . 58

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Index

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Alb_UG.book Page i Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide

Alb_UG.book Page ii Friday, November 1, 2002 4:22 PM

iii

Preface

Alb_UG.book Page iii Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Preface

Alb_UG.book Page iv Friday, November 1, 2002 4:22 PM

Preface

ABOUT THIS GUIDE

The Stylistic ST4000P Series pen tablet PC is a high-

performance, pen-based computer that has been

designed to support MicrosoftWindows 2000

Professional or Windows XP Professional.

This manual explains how to operate your Fujitsu

Stylistic ST4000P Series pen tablet PC’s hardware and

built-in system software.

The Stylistic ST4000P Series pen tablet PC is a completely

self-contained unit with an active-matrix (TFT) color

LCD display and a passive Touch Panel. It has a powerful

interface that enables it to support a variety of optional

features.

Conventions Used in the Guide

Keyboard keys appear in brackets.

Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].

Pages with additional information about a specific topic

are cross-referenced within the text.

Example: (See page xx.)

On screen buttons or menu items appear in bold

Example: Click OK to restart your pen tablet PC.

DOS commands you enter appear in Courier type.

Example: Shut down the computer?

FUJITSU CONTACT INFORMATION

Service and Support

You can contact Fujitsu Service and Support in the

following ways:

■Toll free: 1-800-8Fujitsu (1-800-838-5487)

■Fax: 1-901-259-5700

■E-mail: 8fujitsu@fujitsupc.com

■Web site: http://www.fujitsupc.com

Before you place the call, you should have the

following information ready so that the customer

support representative can provide you with the

fastest possible solution:

■Product name

■Product configuration number

■Product serial number

■Purchase date

■Conditions under which the problem occurred

■Any error messages that have occurred

■Hardware configuration

■Type of device connected, if any

Fujitsu Online

You can go directly to the online Fujitsu product catalog

for your pen tablet PC by going to the Fujitsu web site at:

http://www.fujitsupc.com

WARRANTY INFORMATION

Your Stylistic ST4000P Series pen tablet PC is backed by

either a standard one year International Limited

Warranty. A three-year International Limited Warranty is

available as an option. Check the service kit that came

with your system for warranty terms and conditions.

POINT

The point icon highlights information that will enhance

your understanding of the subject material.

CAUTION

The caution icon highlights information that is

important to the safe operation of your computer, or to

the integrity of your files. Please read all caution

information carefully.

WARNING

The warning icon highlights information that can be

hazardous to either you, your Stylistic ST4000P Series

pen tablet PC or your files. Please read all warning

information carefully.

POINT

You must have an active internet connection to use the

online URL links.

Alb_UG.book Page v Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Preface

Alb_UG.book Page vi Friday, November 1, 2002 4:22 PM

vii

Getting Started with

Your Pen Tablet PC

Alb_UG.book Page vii Friday, November 1, 2002 4:22 PM

viii

Stylistic ST4000P Series User’s Guide – Section One

Alb_UG.book Page viii Friday, November 1, 2002 4:22 PM

Getting Started

Getting Started with Your Stylistic Pen Tablet PC

Figure 1-1 Stylistic ST4000P Series Pen Tablet PC

The Stylistic ST4000P Series pen tablet PC is a high-

performance, pen-based computer that has been

designed to support Microsoft Windows 2000 Profes-

sional or Windows XP Professional. This chapter

provides an overview of the Stylistic ST4000P Series pen

tablet PC and its features.

IN-BOX ITEMS FOR THE STYLISTIC ST4000P

SERIES PEN TABLET PC

Verify that the following items are included in the box

with your pen tablet PC:

• Stylistic ST4000P Series battery

•Power cord

• AC adapter

• Screen protectors (quantity: 2)

• Stylistic ST4000P Series pen

• Pen tips (quantity: 5)

•Pen tether

Alb_UG.book Page 1 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

OPTIONAL ACCESSORIES

The following optional accessories* can be used with the Stylistic ST4000P Series pen tablet PC. Refer to the

instructions provided with these accessories for details on their use.

* For the latest list of accessories available for your Stylistic ST4000P Pen Tablet PC, be sure to frequently

check the Fujitsu Web site at: www.fujitsupc.com.

Table 1-1 Stylistic ST4000P Optional Accessories

Peripheral/Accessory Fujitsu Part Number

Docking Options

Stylistic ST4000 Series Tablet Dock, with CD-ROM drive FPCPR33AP

Stylistic ST4000 Series Tablet Dock, with Combo DVD/CD-RW drive FPCPR32AP

Carrying Cases

Stylistic ST4000 Series executive leather portfolio case FPCCC25

Stylistic ST4000 Series ballistic nylon portfolio case FPCCC26

Stylistic ST4000 Series Bump Case FPCCC24

Harsh Environment Case FPCCC27

Storage Options

External USB floppy disk drive FPCFDD12

Memory

256MB SO DIMM, 133MHz FPCEM43

512MB SO DIMM, 133MHz FPCEM44

128MB Compact Flash Card FPCEM02

256MB Compact Flash Card FPCEM03

Compact Flash Card Adapter FPCFA01

Power Options

AC adapter with US cord FPCAC23

Main Battery FPCBP63AP

Auto/Airline Adapter FPCAA02

Battery Charger FPCBC06

Additional Accessories

Infrared keyboard FPCKB41A1P

USB keyboard FMWKB5A

Infrared Mouse FPCMO07

Stylistic ST4000P Series pen (5-pack) FPCPN08AP

Screen Protectors (12-pack) FPCSP03AP

Pen tether FMWST2

Alb_UG.book Page 2 Friday, November 1, 2002 4:22 PM

Getting Started

STYLISTIC PEN TABLET PC FEATURES

Features and controls that you use to operate the Stylistic ST4000P Series pen tablet PC are outlined below and illus-

trated in Figures 1-1 through 1-5. Details on using these features and controls are provided later in this manual.

Figure 1-2 Stylistic ST4000P Series Pen Tablet PC Features (Front View)

Front Features: 1

•System status LEDs: Indicate the operational status of

the pen tablet PC and hard disk drive, the charge level

of the battery, and the status of the hovering mode.

•Power On/Off/Suspend/Resume button: Allows you

to turn on, off, suspend, resume, hibernate or wake

the pen tablet PC’s operation in order to optimize

battery life.

•Infrared keyboard/mouse port: The infrared port

wraps around the front and bottom of the display,

and is used for communicating with a proprietary

infrared keyboard or mouse.†

•Application buttons: Allow you to quickly launch

pre-defined applications and utilities by pressing a

button.

• Navigation buttons: The navigation buttons allow

you to move: Page Up/Page Down, Tab Right/Tab

Left, Cursor Up/Cursor Down, and Cursor Right/

Cursor Left.

•Speaker: Allows you to listen to mono audio files.

• Built-in Microphone: The built-in microphone allows

you to input mono audio.

† These peripherals and accessories are sold separately.

Infrared

Power On/Suspend/

Application

System

Status

Resume Button

Built-in Microphone

Speaker

Navigation

Buttons

Keyboard/

Buttons

LEDs

User-Programmable

Application Buttons

Mouse Port

Alb_UG.book Page 3 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

Figure 1-3 Stylistic ST4000P Series Pen Tablet PC Features (Back View)

* The system is configured with one of two modules: a standard modem module or an optional wireless LAN/modem

combo module.

Back Features: 1

•System interface connector: Allows you to connect

the optional Stylistic Tablet Dock.†

•Removable battery: Can be removed and replaced

with a charged battery.†

•Battery release latch: Used to release the removable

battery.

•Tablet Dock latch point: Allows you to attach the

system to an optional Tablet Dock. †

•Memory module cover: Removable cover over the

memory modules.

•Thermal Suede: Several areas of the system back are

covered with “thermal suede”. This material should

not be removed. It is designed to minimize the

temperature of the system for the user when a

running system is carried for a period of time.

•Wireless LAN module cover: Provides protection for

the optional wireless LAN radio solution.†

• Wireless LAN On/Off switch: For systems with a

wireless device installed, this switch turns the device

on and off. You should switch the device off when it

is not in use in order to maximize battery life.

•Hard disk drive cover: Covers the hard disk drive

module.

†These peripherals and accessories are sold separately.

Hard Disk

Battery

Memory

Battery

System

Wireless LAN

Release

Latch

Pack

Module

Cover

and/or Modem

Module Cover*

Interface

Connector

Drive Cover

Tablet Dock

Latch Point

Tablet Dock

Latch Point

Wireless

LAN On/Off

Switch*

Wireless

LAN

Antenna*

(inside case)

Thermal

Suede

Latch Point

Alb_UG.book Page 4 Friday, November 1, 2002 4:22 PM

Getting Started

Figure 1-4 Stylistic ST4000P Series Pen Tablet PC Features (Top View)

Top Features: 1

•Pen: The main input device that you use to execute

programs and enter data. A pen holder is built into

the pen tablet PC to store the pen when not in use.

•Microphone Jack: Allows you to connect an external

microphone.

•Headphone Jack: Allows you to connect a set of stereo

headphones.

•PC Card slot: Allows you to install PC Cards in the

system.

•IrDA/FIR port: Provides an infrared interface for

communication with devices compliant with IrDA

Standard Revision 1.1.

•USB ports: Allow you to connect Universal Serial

Bus-compliant devices (compliant with USB

Standard Revision 1.1) to the pen tablet PC.

Additional USB ports are located on the optional

Tablet Do c k.

•IEEE 1394 Jack: Allows you to connect between your

pen tablet PC and peripherals such as a digital video

camera.

•Air flow vents: Provides secondary cooling for

processor. (Do not obstruct the vents.)

†These peripherals and accessories are sold separately.

Pen Holder

PC Card Slot PC Card

IrDA Port

USB Ports

Microphone

Headphone

IEEE 1394 Jack

Eject Button

Jack

Air flow vents

Pen Tether

Attachment

Point

Alb_UG.book Page 5 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

Figure 1-5 Stylistic ST4000P Series Pen Tablet PC Features (Left Side View)

* The system is configured with one of two modules: a standard modem module or an optional wireless LAN/modem

combo module. The mini-PCI expansion slot into which these modules are plugged (located under the cover) can be

used to accommodate other mini-PCI devices.

Left-Side Features: 1

•Modem jack: Allows you to connect a standard RJ-11

connector to the pen tablet PC’s internal 56 Kbps

modem. Note that the internal 56 Kbps LAN/modem

module installed in the Stylistic ST4000P Series pen

tablet PC has actual maximum transfer rates of 53

Kbps (receive), 33.6 Kbps (send), and 14.4 Kbps

(fax). Download rates are limited to 53 Kbps in the

United States due to FCC restrictions.

•LAN jack: Allows you to connect a standard RJ-45

connector to the pen tablet PC’s internal local area

network (LAN).

•DC input connector: Allows you to connect the AC

adapter or auto adapter.†

•Air flow vents: Provides secondary cooling for

processor. (Do not obstruct the vents.)

•Kensington™ lock slot: Allows you to attach a

Kensington MicroSaverTM-compatible security

cable.†

•External Monitor Connector: The External Monitor

connector allows you to connect an external CRT

monitor.

†These peripherals and accessories are sold separately.

Air Flow VentsModem Jack*

LAN Jack*

Kensington™ Lock Slot

DC Input Jack External Monitor Connector

(behind door)

Latch Point

Alb_UG.book Page 6 Friday, November 1, 2002 4:22 PM

Getting Started

Figure 1-6 Stylistic ST4000P Series Pen Tablet PC Features (Right Side View)

Right-Side Features: 1

•Pen: The main pointing device that you use to execute

programs and enter data. A pen holder is built into

the pen tablet PC to store the pen when not in use.

•Air flow vents: Provides secondary cooling for

processor. (Do not obstruct the vents.)

•Infrared keyboard/mouse port: The infrared port

wraps around the front and bottom of the display,

and is used for communicating with a proprietary

infrared keyboard or mouse.†

•Tablet Dock latch point: Allows you to attach the

system to an optional Tablet Dock. †

†These peripherals and accessories are sold separately.

Air Flow Vents Pen / Pen Holder

Infrared Keyboard/Mouse Port

Latch Point

Alb_UG.book Page 7 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

STATUS DISPLAY

Icons appear in the Status display indicating the status of

system functions such as system power and battery

charge level. The location of icons in the Status display is

shown in Figure 1-7.

Table 1-2 explains how individual icons are displayed,

and describes what the variations of that display indi-

cate. (If an icon is not displayed, it indicates that the

related system function is off or inactive.

Figure 1-7 Status Display Icons

Power

Charge/DC In

Battery

HDD Access

Hovering Mode

In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the

rate of one second on, five seconds off.

Icon Mode/State LED State Remarks

Power • On State

• Idle Mode

Green, continuous The system is powered on and ready for use.

• Suspend-to-RAM Green, blinking The system has suspended and saved active

settings to RAM.

• Off State

• Hibernate

(Save-to-Disk)

Off The system has suspended and saved settings

and data to the hard disk drive.

Charge/

DC In

• On State

• Idle Mode

• Suspend-to-RAM

• Hibernate

(Save-to-Disk)

• Off State

Amber AC adapter and battery are available and system

is charging.

Green • AC adapter and battery are available and

system is not charging (battery fully

charged).

• AC adapter is available but battery is not

present.

Amber, blinking AC adapter and battery are available and waiting

to charge (battery is out of thermal range).

Off AC adapter is not available.

Alb_UG.book Page 8 Friday, November 1, 2002 4:22 PM

Getting Started

Table 1-2 System Status Indicators

Battery • On State

• Idle Mode

Green, continuous Battery charge is between 50%-100%

Amber, continuous Battery charge is between 13%-49%

Red, continuous Battery charge is between 0%-12%

Red, blinking There is a battery error.

• Suspend-to-RAM,

without AC adapter

• Suspend-to-RAM

with AC adapter

Green, blinking slow Battery charge is between 50%-100%.

Amber, blinking slow Battery charge is between 13%-49%.

Red, blinking slow Battery charge is between 0%-12%.

• Hibernate

(Save-to-Disk),

with AC adapter

• Off State

Off Battery is not installed, or system is off or in

Hibernate mode.

• Hibernate

(Save-to-Disk),

without AC adapter

If battery is inserted during power off, LED blinks

amber for 4 seconds to detect battery. Battery

status is displayed for 5 seconds after that.

HDD

Access

• On State (or

flashing)

• Idle Mode

Green Displayed when hard disk drive is accessed.

• Suspend-to-RAM

• Hibernate

(Save-to-Disk)

• Off State

Off Hard disk drive is not being accessed.

Hovering

Mode

• Hovering mode Green Hovering mode is active.

• Non-hovering

mode Off Hovering mode is not active.

In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the

rate of one second on, five seconds off.

Icon Mode/State LED State Remarks

Alb_UG.book Page 9 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

APPLICATION BUTTONS

The six application buttons are located on the upper

right-hand side of a vertically-oriented system. (See

figure 1-2 on page 3 for location). Three of the buttons

have secondary functions. The secondary functions are

activated by pressing the Function (Fn) button while

pressing the application button.

The buttons also have separate tertiary functions that

can be used while the system is booting up. For more

information about the tertiary functions, refer to

Table 1-5 on page 13.

POINT

Ctl-Alt-Del is the only Application button that can be

used while the system is logging on or when the system

is locked (i.e., when you have the Logon or Computer

Locked window showing on your desktop).

Button Icon

and Name

(Primary)

Tablet Icon

(Fn +

Button)

(Secondary)

Description

Ctl-Alt-Del

Button

The Ctl-Alt-Del button performs two functions:

• Pressing the Ctl-Alt-Del button for up to one second allows you to log on

after boot, after locking the workstation, or after resuming from power

management

• After log-on, pressing the Ctl-Alt-Del button for up to one second launches

the Windows Task Manager.

Right-Click

Button

Hovering

Mode

When you press the Right-click button, your pen switches its function from left

mouse button to right mouse button emulation. To generate a right mouse button

click, tap on the application button once and then tap on the display.

When you press the Fn + Right-click buttons at the same time, they provide a

Hovering function. Hovering mode provides you with better cursor control. When

hovering is enabled, the cursor can be positioned over an area of the screen

without activating it. This is useful when you are attempting to read pop-up text

associated with an icon, simulating mouse rollover, selecting a small icon, or

beginning a paint session. Note that when Hovering Mode is active, the Hovering

Mode Status Display LED is lit (see Table 1-2). Pressing the Fn + Right-click

buttons at the same time again exits the Hovering function

Orientation

Button

When you press the Orientation button, the system screen orientation changes

from portrait (vertical) to landscape (horizontal) or from landscape to portrait.

When you would like to use the tablet as an eBook, for example, you would use

the portrait orientation, when accessing spreadsheets, you would more typically

use a landscape orientation.

Escape

Button Application

A Button

The Escape application button acts the same way as an Escape key on a keyboard.

When you press the Fn + Esc buttons at the same time*, they act to invoke a pre-

determined application or generate a combination keystroke, as assigned the

Tablet Button Settings utility. (You can change the settings in Control Panel ->

Tablet Button Settings).

By default, pressing the Fn + Esc combination acts the same as if you had pressed

Ctl + Esc on a keyboard: the Start menu is launched.

Alb_UG.book Page 10 Friday, November 1, 2002 4:22 PM

Getting Started

Table 1-3 Application Buttons - Primary and Secondary Functions

* The Fn button has a handy “sticky” feature that allows you to press the two buttons in immediate succession, rather

than at exactly the same time. After pressing the Fn button, you have a short time (two or three seconds) to press the

second button. Note that this feature is not available with the Right-Click/Hovering button.

Enter

Button Application

B Button

The Enter application button acts the same way as an Enter key on a keyboard.

Pressing the Fn + Ent buttons at the same time*, acts to invoke a pre-determined

application or keystroke combination, as assigned the Tablet Button Settings utility.

(You can change the settings in Control Panel -> Tablet Button Settings).

By default, pressing the Fn + Ent combination acts the same as if you had pressed

Alt on a keyboard: it selects a main menu in the typical Windows application.

Function

Button

The Function button works in conjunction with the other application buttons to

provide additional functionality for the buttons. Refer to specific details above.*

Pressing the Fn button twice in succession (within the “sticky” time*), causes the

Fujitsu menu to appear on your screen, allowing you to modify certain system

settings.

Button Icon

and Name

(Primary)

Tablet Icon

(Fn +

Button)

(Secondary)

Description

Alb_UG.book Page 11 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

NAVIGATION BUTTONS

The two navigation buttons are located on the lower

right-hand side of a vertically-oriented system. (See

figure 1-2 on page 3 for location). Each of the buttons can

be toggled by pressing either end of the button.

The buttons have dual functions. The secondary func-

tions are activated by pressing the Function (Fn) button

while pressing the application button*.

The buttons also have separate tertiary functions that

can be used while the system is booting up. For more

information about the tertiary functions, refer to

Table 1-5 on page 13.

* The Fn button has a handy “sticky” feature that allows you to press the two buttons in immediate succession,

rather than at exactly the same time. After pressing the Fn button, you have a short time (two or three seconds) to

press the second button. Note that this feature is not available with the Right-Click/Hovering button.

Table 1-4 Navigation Buttons

POINT

Ctl-Alt-Del is the only Application button that can be

used while the system is logging on or when the system

is locked (i.e., when you have the Logon or Computer

Locked window showing on your desktop).

Buttons/icons Purpose (when pressed alone)

(“Primary” function)

Purpose (when pressed with Fn button)

(“Secondary” function)

This button consists of Up and Down

segments. When the Up portion is

pressed, you will scroll up one page.

When the Down portion is pressed, you

will scroll down one page.

When pressed with the Function (Fn) button*, the

Up portion of this button allows you to tab right.

When pressed with the Function (Fn) button*, the

Down portion of this button allows you to tab left.

This button consists of Up and Down

segments. When the Up portion is

pressed, the cursor will move up.

When the Down portion is pressed, the

cursor will move down.

When pressed with the Function (Fn) button*, the

Up portion of this button will move the cursor to the

right.

When pressed with the Function (Fn) button*, the

Down portion of this button will move the cursor to

the left.

Alb_UG.book Page 12 Friday, November 1, 2002 4:22 PM

Getting Started

TERTIARY FUNCTIONS OF APPLICATION AND NAVIGATION BUTTONS

While you are booting up your system, the Application

Buttons and Navigation buttons can be used for entering

and navigating through the Basic Input-Output System

(BIOS), and for invoking the Advanced Options Menu,

where you can enter different modes (such as Safe

Mode).

The BIOS is a program and a set of parameters that are

stored in ROM which tests and operates your pen tablet

PC from when you turn it on until it loads your installed

operating system from disk. Information from the BIOS

is transferred to the operating system to provide it with

information on the configuration and status of the hard-

ware.

The system is booting up while the Fujitsu logo is

displayed immediately after turning on the system. The

table below indicates how the buttons act while the

system is booting up and while you are in the BIOS.

Table 1-5 Tertiary Functions of Application and Navigation Buttons

Buttons/icons Purpose (when pressed while the system is booting up)

Ctl-Alt-Del

Button

Pressing the Ctl-Alt-Del button while the system is booting up takes you into the BIOS setup utility.

This is the same as if you had tapped [F2] on a keyboard.

Right-Click

Button

Pressing the Right-Click button while the system is booting up opens the Boot Options menu. This is

the same as if you had tapped [F12] on a keyboard.

Orientation

Button

Pressing the Orientation button while the BIOS setup screen is open causes the selected item (if

applicable) to change to the next item. Pressing this is the same as tapping the spacebar on a

keyboard.

Escape Button

Pressing the Esc button while the BIOS is open acts to escape from the BIOS. This is the same as if

you had tapped [Esc] on a keyboard.

Enter Button

Pressing the Ent button while the BIOS is open acts the same as the [Ent] button on a keyboard.

Function Button

Pressing the Fn button while the system is is displaying the operating system boot menu opens the

Advanced Operating System Options menu. This menu allows you to enter different operating

system modes (such as Safe Mode). Pressing this button is the same as if you had tapped [F8] on a

keyboard.

Pressing the top half of the upper navigation button while the BIOS setup screen is open causes the

cursor in the BIOS setup screen to move up. This is the same as if you had tapped Arrow Up on a

keyboard. This feature is also functional in the operating system boot menu.

Pressing the bottom half of the upper navigation button while the BIOS setup screen is open causes

the cursor in the BIOS setup screen to move down. This is the same as if you had tapped Arrow Down

on a keyboard. This feature is also functional in the operating system boot menu.

Pressing the top half of the lower navigation button while the BIOS setup screen is open causes the

cursor in the BIOS setup screen to move right. This is the same as if you had tapped Arrow Right on a

keyboard.

Pressing the bottom half of the lower navigation button while the BIOS setup screen is open causes

the cursor in the BIOS setup screen to move left. This is the same as if you had tapped Arrow Left on

a keyboard.

Alb_UG.book Page 13 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

CONNECTORS AND PERIPHERAL INTERFACES

Connectors and peripheral interfaces on the Stylistic

ST4000P Series pen tablet PC allow connection of a

variety of devices. Specific locations are illustrated in

Figures 1-2 through 1-5.

Table 1-6 provides a description of each peripheral

connector on the Stylistic ST4000P Series pen tablet PC.

Each of the illustrated icons is either molded into or

printed on the pen tablet PC case.

Connector/

Peripheral

Pen Tablet

PC Icon Purpose

DC in

connector

Connect an external power source such as the AC adapter or auto/

airline adapter.

USB Port Connect Universal Serial Bus 1.1 compliant devices to the pen tablet PC.

PCMCIA

Card slot

Install a Type I or Type II PC Card.

Microphone

jack

Connect an external microphone. The internal microphone is disabled

when you plug in an external microphone.

Headphone

jack

Connect stereo headphones or powered external speakers. The internal

speaker is disabled when you plug in external headphones or powered

speakers.

IrDA/FIR port An infrared transceiver built into the pen tablet PC allows you to

communicate with other devices that are compliant with the IrDA

Standard Rev. 1.1. Effective range for infrared communication is about

3 feet, and within 15 degrees off center. A clear line-of-sight path must

exist between the IrDA port on the pen tablet PC and the IrDA

transceiver on the other device.

Modem Connect a telephone line to the optional internal modem using a

standard RJ-11 telephone plug.

Tablet Dock

port

Connect the Stylistic ST4000P Series dock or other approved docking

device. Refer to documentation accompanying the docking device for

more information.

Infrared

keyboard/

mouse port

An infrared receiver built into the pen tablet PC allows you to

communicate with a wireless infrared keyboard or mouse. The keyboard

infrared port works optimally between 10 to 30 cm (approximately 4 in.

to 12 in.) from the keyboard infrared port, located on the bottom edge

of the pen tablet PC. Ensure that there is a clear line-of-sight path

between the infrared receiver on the pen tablet PC and the infrared

transmitter on the keyboard or mouse.

KensingtonTM

Lock slot

The Kensington MicrosaverTM security slot allows you to secure the pen

tablet PC using Kensington-compatible locking devices.

Alb_UG.book Page 14 Friday, November 1, 2002 4:22 PM

Getting Started

Table 1-6 Peripheral Connectors/Interfaces

IEEE 1394 jack The IEEE 1394 jack allows you to connect between your pen tablet PC

and peripherals such as a digital video camera.

Suspend/

Resume button

The Suspend/Resume/Power On button allows you to suspend pen

tablet PC activity without powering off, resume your pen tablet PC

from suspend mode, and power on the system when it has been shut

down from Windows.

Page Up/

Page Down

The Page Up/Page Down button allows you to navigate quickly from

page to page without scrolling.

Local Area

Network (LAN)

The LAN (RJ-45) jack is used to connect the internal Fast Ethernet (10/

100 Base-T/Tx) to a Local Area Network (LAN) in your office or home, or

broadband devices such as a cable modem, DSL, or satellite internet.

Battery Release

Latch

The battery release latch allows you to remove the battery from your

system for storage or replacement.

Wireless LAN

On-Off Switch

The wireless LAN switch allows you to turn power to the optional

wireless LAN device on and off.

Connector/

Peripheral

Pen Tablet

PC Icon Purpose

Alb_UG.book Page 15 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section One

Alb_UG.book Page 16 Friday, November 1, 2002 4:22 PM

Using Your

Stylistic ST4000P

Series Pen Tablet PC

Alb_UG.book Page 17 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Two

Alb_UG.book Page 18 Friday, November 1, 2002 4:22 PM

Using Your Stylistic ST4000P

Using the Stylistic ST4000P Series Pen Tablet PC

This chapter covers the fundamental concepts, basic

system operation and use, and system functions of the

Stylistic ST4000P Series pen tablet PC. You should famil-

iarize yourself with this information before you attempt

to operate the system.

SYSTEM STATES

Before you begin using the Stylistic ST4000P Series pen

tablet PC, review the different system states (or modes)

that the system can use. Being familiar with these states

will help you determine whether it is appropriate to turn

on, resume, suspend, hibernate or shut down the system

when you begin or end a session. System behavior for

each system state is described briefly in the following,

with each system state listed in decreasing order of power

usage:

•On state: The system is running and the display

screen is on.

•Idle state: Some system functions are regulated or

turned off to conserve power. The display screen may

be turned off. The system returns to the On state

when pen activity or other input is detected.

•Suspend-to-RAM mode (S3): System operation is

suspended. Most system functions are turned off to

conserve power. Power to memory is on, maintaining

data in programs that were running before system

operation was suspended. The system does not

respond to the pen or other input when in Suspend-

to-RAM mode. Refer to the “Resuming System

Operation” section later in this chapter for

information on returning the system to the On state.

•Hibernate mode (Save-to-Disk) (S4): System

operation is suspended. All system functions are

turned off to conserve power. Active data in programs

that were running before suspending system

operation is stored on the hard disk drive. The system

does not respond to the pen or other input. Refer to

the “Resuming System Operation” section later in this

chapter for information on returning the system to

the On state.

•Off state: All system functions are turned off to

conserve power. The system does not respond to the

pen or other input. The system boots at the next

system power-on.

Your system may be configured to enter some of these

states automatically after a period of inactivity to

conserve battery power.

When you use the Stylistic ST4000P Series pen tablet PC,

you can change the current system state in a number of

ways, depending on the system’s current state. To deter-

mine the current system state, observe the Power icon in

the Status display. Table 2-1 on page 20 gives the different

system states represented by the Power icon and describes

how you can change the system state from the current

state.

POINT

Prior to using your system, be sure to fully charge the

battery if you plan to run on battery power. Failure to

do so may result in erratic performance.

POINT

The system consumes the same amount of power

whether it is in Hibernate (Save-to-Disk) mode or the

Off state.

Alb_UG.book Page 19 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Two

Table 2-1 Changing System States

*Information in Table 2-1 on page 20 is supplied to help you understand which system states your system can enter from

the current system state. Refer to the procedures on starting the system, shutting down the system, suspending system

operation, and resuming system operation given later in this chapter.

†Your system may be configured to use either Suspend-to-RAM mode or Hibernate mode.

POWERING UP THE PEN TABLET PC

Follow the procedure below to start the Stylistic

ST4000P Series pen tablet PC. Before you begin, confirm

that the system is in the Off state. To do so, observe the

Status display. If the Power icon is not visible in the

Status display, the system is in Off state or in Hibernate

(Save-to-Disk) mode and it is safe to perform this proce-

dure. If the Power icon is visible (either blinking or on

continuously), do not perform this procedure. See

“System States” earlier in this chapter for details on

modes represented by the Power icon.

1. Ensure that the battery in your pen tablet PC is

sufficiently charged, or connect an external power

source such as the AC adapter or auto adapter to

your pen tablet PC.

2. Press the Power On/Suspend/Resume button to start

the system.

After performing initialization, the system starts the

operating system installed on the hard disk drive. Once

the operating system is running, you can use the system.

SHUTTING DOWN THE SYSTEM

Follow these steps to shut down and turn off your

system:

1. If system operation has been suspended, resume

system operation. See “Resuming System Opera-

tion” later in this chapter for details.

2. Save your work and close all running programs.

3. Choose Shut Down from the Windows (2000 Profes-

sional or XP Professional) Start menu.

4. Carry out the Shut Down command.

The system is now in the Off state.

SUSPENDING SYSTEM OPERATION

The pen tablet PC allows you to suspend the system

operation without closing programs or exiting the oper-

ating system. Use this feature to conserve battery power

when a system shutdown is not practical or when the

battery needs to be changed.

Icon Appearance Current State To Change State*

Power icon

displayed

continuously

On State

Idle State

To enter the Off state, shut down the system using the Start menu on your

system.

To enter Suspend-to-RAM or Hibernate (Save-to-Disk)† state, suspend system

operation using either a hardware or software suspend.

Power icon blinking Suspend-to-

RAM†

To enter the On state, resume system operation by pressing the Suspend/

Resume button.

To enter the Off state, resume system by pressing the Suspend/Resume

button, then shut down your system.

Power icon not

displayed

Off State, or,

Hibernate

(Save-to-Disk†)

To enter the On state, start your system, or resume system operation by

pressing the Suspend/Resume button.

POINT

If you have set your system to turn power off from the

Power Options utility in the Control Panel, the

following procedure will not be possible, since pressing

the button shuts the system down rather than

suspending it. To change your power options, go to

Start -> Settings -> Control Panel -> Power Options.

Alb_UG.book Page 20 Friday, November 1, 2002 4:22 PM

Using Your Stylistic ST4000P

To suspend system operation:

1. Press the Suspend/Resume button, or carry out the

Standby command from your operating system or

power management program. (If your system is

configured to suspend operation using Hibernate

mode, which is explained later in this procedure, a

message is displayed while data is saved to your hard

disk.)

2. The Power icon either flashes (Suspend-to-RAM) or

is not displayed (Hibernate) when system operation

is suspended, depending on how your system is

configured. At this point, programs that were

running are stopped, active data is saved, and the

system enters one of two different low-power states,

or suspend modes, as explained in the following

paragraphs.

3. Observe the Power icon in the Status display to deter-

mine which suspend mode your system is using.

•Power icon is blinking: Suspend-to-RAM mode.

In this mode, active data is saved by maintaining

power to RAM while most other system components

are powered off. The Battery Gauge icon in the Status

display indicates the battery charge level.

•Power icon is not displayed: Hibernate mode.

In this mode, active data is stored on the hard disk

drive and power usage is reduced to the same level

used in the Off state. When the system is in Hibernate

mode, the Battery Gauge icon is not visible in the

Status display. In this mode, there is no danger of

losing data if battery power is lost.

If you have successfully performed this procedure,

system operation is now suspended. Refer to

“Resuming System Operation” later in this chapter to

resume system operation. Also, note the following

with regard to suspending system operation:

• You can remove the battery while the system is in

Suspend-to-RAM or Hibernate modes in order to

install a charged battery. To prevent losing unsaved

data, wait until system operation has suspended

before you remove the battery. Note that after you

remove the battery, you have approximately five

minutes to replace it with a new battery or to plug in a

power supply before the bridge battery is depleted.

• Your system may be configured to suspend operation

automatically after a period of inactivity.

• Your system may be configured to enter Hibernate

mode automatically after a period of time in Suspend-

to-RAM mode.

• The system uses a small amount of battery power

when in Suspend-to-RAM mode. Eventually, the

battery will become fully discharged.

• If the battery charge drops to a Low-Battery Warning

level while the system is running, the system will beep

periodically. If this occurs, suspend system operation,

shut down the system, or attach an external power

source, such as the AC adapter, to the pen tablet PC.

• If the battery charge drops to a Critically Low level

while the system is running, the system is forced into

a pre-selected mode (Suspend-to-RAM or

Hibernate). If this occurs, you must either install a

charged battery, or connect an appropriate external

power source such as the AC adapter before you can

resume system operation. (If the battery charge drops

to a Critically Low level while the system is in

Suspend-to-RAM mode, the system stays in Suspend-

to-RAM mode until power is restored or totally

dissipated.)

• Suspending system operation interrupts data

communications; therefore, some programs may

block the system from suspending to prevent an

interruption.

• The suspend action of the Suspend/Resume button

may be disabled to prevent accidental interruption. If

this is the case, pressing the Suspend/Resume button

will not suspend system operation as described here.

(In this case, suspend mode can only be achieved

using the system software). Contact your local help

desk or reseller if your system configuration is not

suitable.

• If your system is equipped with a PC Card that allows

you to connect to a wired or wireless network, you

CAUTION

If you are replacing the battery, wait until system

operation is suspended and the power icon is flashing

before you remove the battery. Failure to do so could

result in loss of your unsaved data. (Note that if the

Resume On LAN function is enabled in the BIOS setup,

you should not remove the battery unless the system is

shut down. When Resume ON LAN is enabled, the

bridge battery is disabled in order to optimize battery

life.)

POINT

If you will not be using the system for an extended

period of time, shut down the system rather than using

Suspend-to-RAM mode.

Alb_UG.book Page 21 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Two

may be logged off the network after a period of

inactivity while system operation is suspended.

Contact your network administrator or help desk for

details on log-off parameters for your network.

RESUMING SYSTEM OPERATION

To resume system operation from either Suspend-to-

RAM or Hibernate modes, press the Suspend/Resume

button.

•From Suspend-to-RAM mode

Status lights indicate that the system state is

changing. It may take up to a minute before the

system returns to the On state and system operation

resumes. Note that the display turns on shortly

before the pen becomes active due to the power-up

sequences observed by the system.

•From Hibernate (Save-to-Disk) mode

Active data is read from the hard disk drive, and the

system returns to the On state after a short time.

• Use the system as you normally would once system

operation resumes.

All programs resume at the point where execution

stopped when system operation was suspended.

USING THE PEN

You can use the Stylistic ST4000P Series pen to select

items, and to navigate through programs on the pen

tablet PC. The pen can be used like a two button mouse

when used in conjunction with the right-mouse button.

Here are some hints on using the pen similar to a two-

button mouse on a desktop system:

•To select an object, tap the pen tip on the object

once. This functions like a left mouse button click.

•To “double-click” an object, tap twice on the object

quickly. (The pen double-click speed is in sync with

the mouse double-click speed, and can be changed by

going to Start-> Settings -> Control Panel -> Mouse.

•To generate a “right mouse button single-click”,

press the Right-Click Application Button , then

tap on the object once.

•To move, or “drag”, an object on the screen, place the

pen tip directly over the object, then as you hold the

pen tip against the screen, move the pen.

INSTALLING A PEN TETHER

To prevent dropping or losing your pen, you should

attach it to your system using the pen tether that is

included with the system.

To attach the pen tether to your Tablet PC, perform the

following steps:

1. Attach the end of the pen tether with the smaller

loop to your pen. Do do so, push the end of the

tether through the hole in the pen, then thread the

opposite end of the tether through the loop. (See

Figure 2-1)

Figure 2-1 Installing a Pen Tether

2. Attach the end of the pen tether with the larger loop

to the attachment point on your pen tablet. To do so,

insert the end of the pen tether through the attach-

ment point, then feed the pen through the large loop

in the tether.

POINT

Note that power to several system components must be

restored before system operation resumes. Allow

sufficient time for system operation to resume before

attempting to use the system. If your system uses

Hibernate mode, it will take longer to resume operation

as compared to using Suspend-to-RAM mode. Time is

needed to read data from the hard disk drive.

CAUTIONS

• Ensure that a screen protector is installed on the pen

tablet PC screen before you use the pen. The

warranty does not cover a screen that is scratched as

a result of not using a screen protector.

•Use only the pen provided with your pen tablet PC.

Do not use substitutes that were not designed for the

Stylistic ST4000P Series pen tablet PC. (e.g., ball

point pens, fingernail, or screwdriver). Damage

caused by using an instrument other than the

provided pen is not covered by the system warranty.

Smaller loop

Larger loop

Pen tether

attachment

point

Alb_UG.book Page 22 Friday, November 1, 2002 4:22 PM

Using Your Stylistic ST4000P

CALIBRATING THE PEN

Calibration of the pen adjusts the cursor position on the

screen relative to the position of the pen tip. You calibrate

the pen to adjust the distance error between where the

pen actually touches the screen and where the system

“thinks” the pen is touching. If the event you wish to

invoke is not displayed under the pen tip when you use

the pen, you should calibrate the pen.

Pen calibration may be required due to the following

situations:

• The pen is being used for the first time.

• The previous user of the Stylistic ST4000P Series pen

tablet PC writes with the opposite hand or at a

different pen angle.

• The system has been in use for some time and the pen

has not been recalibrated.

• The original system image has been restored.

To Calibrate the Pen

1. Open the Control Panel from the Start|Settings

menu, and double-tap the Pen Configuration icon. In

the Setup Property page, tap on [Calibrate] to start

calibration.

2. Position the Stylistic ST4000P Series pen tablet PC as

you normally would during use. Be sure to hold the

pen at the angle that you regularly use. Touch the

screen only with the pen tip; inadvertently touching

the screen with your finger or hand during the

calibration process, may result in faulty calibration.

3. Perform the calibration steps according to the

instructions on the screen. The calibration utility

displays a cross-hair symbol in the corners of the

screen, one corner at a time. Hold the pen as you

normally would while using the system and, as

accurately as possible, tap the center of each crosshair

as it is displayed.

4. When the Verify New Pen Calibration Settings

window appears, choose one of the following steps.

• If you are satisfied that you tapped the cross-hairs

accurately, tap Yes. The taps that you performed in

step 3 are then used to calibrate the screen.

• If you do not want to use the new calibration, tap

No.

• If you want to enter a new calibration, tap

Recalibrate. The calibration instructions reappear.

• If you don’t tap the screen within 20 seconds, the

default settings will be used.

If you have successfully performed the procedure above,

the pen is now recalibrated, and you can use the system as

you normally would.

Replacing the Pen

With use, the pen tip may become worn or may pick up

foreign particles that can scratch the screen. A damaged

or worn tip may not move freely, causing unpredictable

results when using the pen. If your pen exhibits these

problems, contact your reseller to purchase replacements.

USING HOVERING MODE

Selecting the Pen Hovering application button on the

Stylistic ST4000P Series pen tablet PC provides you with

better cursor control. When the hovering option is

enabled, the cursor can be positioned over an icon

without activating it. This is useful when you are

performing procedures that require accurate cursor posi-

tioning, such as when simulating mouse rollover,

selecting a small icon, or beginning a paint session.

• To enable hovering, press the Function button

and the Right-Click button at the same

time.

• To disable hovering, press the Function button

and the Right-Click button again.

For help on Normal/Special Hover mode settings in the

Pen Configuration applet, press [F1] to invoke help from

within the applet.

CHARGING THE BATTERY

The Stylistic ST4000P Series battery can be charged while

it is installed in the pen tablet PC. To do so:

1. Connect a DC power source, such as the AC adapter,

to the DC input connector on the pen tablet PC. The

DC Input icon appears in the Status display. If the

battery charge is below 90%, the battery begins

charging and the Charging icon appears in the Status

display. If the battery charge is 90% or higher when

you connect DC power, the battery will not charge,

preventing battery overcharging.

2. Look at the Battery Gauge icon in the Status display

to determine the percent of charge in the battery. See

“Status Display” in Chapter 1 of this manual for a

description of the Battery Gauge icon.

As long as DC power remains connected to the pen tablet

PC, the charging process continues until the battery

charge reaches 100%. Charge times shown in Table 2-2,

“Battery Charging Time" are for a fully discharged

battery charging both while the pen tablet PC is and is

not in use.

Alb_UG.book Page 23 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Two

Table 2-2 Battery Charging Time

* Depends upon the applications in use.

Also note the following with respect to charging the

battery:

• You can use the system, suspend system operation, or

shut down and turn off the system without

interrupting the charging process; however, using the

system while the battery is charging will cause the

battery to charge at a slower rate, as noted in Table 2-

2, “Battery Charging Time".

• As noted in the procedure above, the system will not

begin charging the battery if the battery charge level

is 90% or higher when the system is initially

connected to external DC power. (This prevents the

battery from being overcharged.)

• The Stylistic ST4000P Series battery uses Lithium ion

battery cells which have no “memory effect.” You do

not need to discharge the battery before you begin

charging.

REMOVING AND INSTALLING

THE BATTERY

The battery can be removed from the pen tablet PC and

swapped with a charged battery. The battery can then be

charged in an external charger if one is available. To

remove the battery from the pen tablet PC:

1. Choose one of the following:

• If a charged battery is available, you can suspend

system operation. A built-in “bridge” battery will

maintain the system in Suspend-to-RAM mode

for about 5 minutes while the battery is removed;

this allows time for replacement with a charged

battery.

• If a charged battery is not available, save your

work and close all running programs, then shut

down the system or Hibernate (Save-to-Disk).

• Plug in an external DC power source.

2. Slide the battery release latch in the direction

indicated. (See Figure 1 on page 24 for location).

3. Pull the battery away from the system, as shown in

the illustration and remove the battery from the pen

tablet PC.

If you are using an external battery charger, refer to the

instructions provided with the battery charger.

To install the battery:

1. Orient the battery with the slides in the empty

battery tray. Slide the battery into the tray and press

it firmly until it is seated. When it is properly seated,

the battery release latch should return to position

and lock the battery.

Figure 2-2 Removing the Battery

Once the battery is installed, you can resume system

operation or start and use your system normally.

TIPS FOR CONSERVING BATTERY POWER

You can extend the charge life of your battery by

conserving battery power. (Your results may vary

depending on your application and how the system is

configured.) Here are some suggestions to help you

conserve battery power:

• Use an external power source such as the AC adapter

whenever the system is docked.

• Suspend system operation if you know that you

won’t be using the system for a while.

• Shut down the system if you won’t be using the

system for an extended period of time.

• Use power management (available on the desktop) to

help you conserve power automatically.

• Battery life is dependent upon the operating system,

power settings, and applications in use.

Battery Charge

Level Reached

Approximate

Charge Time

(not in use)

Approximate

Charge Time

(in use)

90% 3.5 hours 7 hours*

100% 4.5 hours 8 hours* POINT

Under Federal, state, or local law, it may be illegal to

dispose of batteries by putting them in the trash. Be

sure to dispose of batteries in accordance with local

government regulations.

Alb_UG.book Page 24 Friday, November 1, 2002 4:22 PM

Using Your Stylistic ST4000P

Operation of the Bridge Battery

When installed in the pen tablet PC, the battery provides

power to some system components—even when the

system is in the Off state. When the battery is removed,

power is supplied to these components by a “bridge”

battery that is built into the pen tablet PC.

The bridge battery is not designed for long-term opera-

tion. To maintain the bridge battery properly, observe the

following measures:

• To prevent draining the bridge battery, always store

the system with a charged battery installed.

• If the bridge battery becomes drained, it takes

approximately 8 hours for it to be fully recharged.

• The bridge battery charges when the AC Adapter is

connected and the system is in On or Off states or

Suspend mode. It charges from the battery only when

the system is in the On state.

MODEM CONNECTION

The Stylistic ST4000P Series pen tablet PC is designed to

accept a standard RJ-11 telephone plug. Connect the plug

to the modem jack located on the left-hand side of the

pen tablet PC (See Figure 1-4 on page 5 for location). The

telephone plug can be installed whether or not the pen

tablet PC has power applied.

If you need assistance configuring the Stylistic ST4000P

Series pen tablet PC modem or LAN, contact your local

help desk or your reseller.

PC CARD SLOT

The Stylistic ST4000P Series Pen Tablet PC Card slot

allows you to install a Type I or Type II PCMCIA Card.

Installing a PC Card

To install a PC card, position the side with the arrow

facing up (i.e., when looking at the tablet’s display side,

the arrow on the card should be visible.) Slide the card

into the PC Card slot, and press it firmly to ensure proper

seating. (See Figure 2-3 for location)

If you need assistance installing a PC Card in the Stylistic

ST4000P Series pen tablet PC, contact your corporate

help desk or your reseller.

Figure 2-3 Installing a PC Card

Removing a PC Card

To remove a PC Card, press the PC Card eject button so

that it pops out. Once the button has popped out, press it

in firmly to eject the card. (See Figure 2-4 for location)

Figure 2-4 Removing a PC Card

REMOVING AND INSTALLING

MEMORY MODULES

There is one DIMM slot in your pen tablet PC and

256MB on the motherboard. 256MB and 512MB

modules are available, so you can install a combination of

up to 768MB in the system.

POINT

• The bridge battery function is disabled if Wake On

LAN is enabled in the BIOS.

• The system arrives with the bridge battery in a

discharged state. Be sure to charge it sufficiently

before relying upon it to support the system in the

event of battery removal.

POINT

The internal 56 Kbps LAN/modem module installed in

the Stylistic ST4000P Series pen tablet PC has actual

maximum transfer rates of 53 Kbps (receive), 33.6 Kbps

(send), and 14.4 Kbps (fax). Download rates are limited

to 53 Kbps in the United States due to FCC restrictions.

Alb_UG.book Page 25 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Two

Installing a Memory Module

To install a DIMM module in the pen tablet PC:

1. Ensure that the pen tablet PC is off. To do so, carry

out the Shut Down command in the Start menu.

(Do not attempt to remove or install a DIMM

module when the system is in Suspend mode or

running.)

2. Remove the two screws from the cover plate on the

back of the pen tablet PC and remove the cover plate

as shown in Figure 2-5.

Figure 2-5 Accessing the Memory Slot

3. Insert the DIMM module in the socket at an angle

and push it down until it locks into place as shown

in Figure 2-6. Note that the DIMM module is keyed

to prevent it from being inserted backwards.

Figure 2-6 Installing a DIMM Module

4. Reinstall the cover and screws that you removed in

step 2.

5. Confirm that the DIMM module is recognized by

the system. To do so, run BIOS Setup. The size of

the DIMM module should be displayed in the Info

menu in BIOS Setup.

The DIMM module is installed in the pen tablet PC and

you can now use the system.

Removing a Memory Module

To remove a DIMM module:

1. Ensure that the pen tablet PC is off. To do so, carry

out the Shut Down command in the Start menu.

(Do not attempt to remove or install a DIMM

module when the system is in Suspend mode or

running.)

2. Remove the screws from the cover plate on the back

of the pen tablet PC and remove the cover plate as

shown in Figure 2-5.

3. Spread the fingers on the socket that lock the DIMM

module in place until the DIMM module is loose.

4. Remove the DIMM module from the socket.

The DIMM module is now removed from the pen tablet

PC. Refer to “Installing a Memory Module” on page 26

to install a new DIMM module.

CAUTION

DIMM replacement should only be performed at a

static-free workstation. Avoid touching connector pins,

circuit boards, and other circuit components on the

drive or pen tablet PC. Electrostatic discharge caused by

doing so can damage sensitive components.

Alb_UG.book Page 26 Friday, November 1, 2002 4:22 PM

Care and

Maintenance

Alb_UG.book Page 27 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Three

Alb_UG.book Page 28 Friday, November 1, 2002 4:22 PM

Care and Maintenance

This chapter gives you pointers on how to care for and

maintain your Stylistic ST4000P Series pen tablet PC.

PROTECTING THE DISPLAY SCREEN

The Stylistic ST4000P Series pen tablet PC is designed to

provide you with years of service. Using a screen

protector will help ensure that the screen remains as clear

as possible. When installed, the screen protector becomes

a durable, replaceable writing surface that protects the

display screen from abrasion.

To obtain additional screen protectors, check with your

reseller, or go to the Fujitsu Web site at www.fujit-

supc.com for ordering information. Additional informa-

tion about installation is included with the screen

protectors.

To install a new screen protector on your pen tablet PC:

1. If a screen protector is already installed on the display

screen, remove it before installing the new screen

protector.

The screen protector is held onto the display screen

surface by a thin strip of adhesive around the edges. A

notch in one corner of the screen protector allows

you to slide your fingernail under the screen

protector for easy removal.

2. Clean the display by wiping the screen gently using a

soft cotton cloth dampened with isopropyl alcohol.

Ensure that all residue has been removed from the

screen before applying a new screen protector.

3. Remove the protective coating from the adhesive side

of the screen protector first, as shown in Figure 3-1.

Figure 3-1 Removing the Protective Sheet

4. Apply the screen protector to the display screen

surface. When doing so, orient the screen protector

with the adhesive side of the screen protector facing

the display screen and the notched corner of the

screen protector oriented as shown in Figure 3-2.

Figure 3-2 Installing the screen protector

5. Apply pressure to the screen protector with your

finger using a continuous wiping motion along the

edges. The adhesive sets completely within 48 hours.

To ensure a good seal between the screen protector

and the display, do not lift the screen protector from

the display once it has been applied.

6. Remove the protective plastic cover from the face of

the screen protector, as shown in Figure 3-3.

Figure 3-3 Removing the protective cover

CAUTION

During normal use of the pen tablet PC, small particles

from the environment can become embedded in the

pen tip and scratch the screen. To prevent scratching

the screen, ensure that a screen protector is installed

before using your pen tablet PC. The warranty does not

cover a screen that is scratched as a result of not using a

screen protector.

CAUTION

■The Stylistic ST4000P Series pen tablet PC is not

waterproof. Do not pour liquids on the system or

wash it with a heavily soaked cloth.

■Do not place items on the top of the display, or dam-

age may occur.

Alb_UG.book Page 29 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Three

7. Clean any residue left behind by the protective

coating from the exposed surface of the screen

protector by wiping gently with a soft cotton cloth

dampened with isopropyl alcohol. Wipe the screen

protector with a soft dry cloth to remove any low-

tack adhesive; this will help prevent the pen tip from

squeaking.

The screen protector is now installed.

STORING THE PEN TABLET PC

Store the Stylistic ST4000P Series pen tablet PC in the

Off state with a fully charged battery installed. You can

store the pen tablet PC in the Off state for about 30 days

with a fully charged battery installed. After this period,

the battery should be recharged or replaced with a

charged battery.

If you intend to store the pen tablet PC for a longer

period of time, the small battery that maintains system

time may need to be replaced. Replacement of the clock

battery should only be performed by authorized techni-

cians.

AVOIDING OVERHEATING

The pen tablet PC monitors its internal temperature. As

the internal temperature approaches the tolerable limits

of heat-sensitive components, system functions are

automatically limited or turned off to prevent damage.

To avoid overheating the pen tablet PC, do not obstruct

the air vents on the top and bottom edges of the pen

tablet PC.

CLEANING THE DISPLAY SCREEN

To clean the pen tablet PC display screen, wipe the

screen surface gently using a soft cotton cloth slightly

dampened with water or isopropyl alcohol.

TROUBLESHOOTING

Solutions to some common problems are described in

the following sections. If you are experiencing a problem

with your pen tablet PC that you cannot solve by taking

the actions described, contact your local help desk or

your reseller for further assistance.

System Will Not Resume Operation

If the system will not resume operation after system

operation has been suspended, check the following

possible causes:

• The battery may either be defective, or discharged to

a critically low level. When the battery reaches a

critically low level, the system is forced into Suspend-

to-RAM mode to avoid a total system power failure.

To correct this problem, either connect an external

power supply (such as the AC adapter), or install a

charged battery in the pen tablet PC.

• The system may be at the critical thermal limit. To

avoid damage to heat-sensitive components, the

system enters Suspend-to-RAM mode when it gets

too hot. System operation cannot be resumed until

the pen tablet PC cools off to a tolerable temperature.

Move the pen tablet PC to a cooler location.

Display Screen Blank or Difficult to Read

If the display screen on your pen tablet PC appears blank

or is unreadable, confirm that the system is running (the

Power icon is displayed continuously on the Status

display), and check the following:

• The system brightness may be set too low, causing

the screen to appear too dark. To change system

brightness, press the Fn button twice to open the

Fujitsu menu. Brightness can be adjusted from the

menu.

• An external monitor may be selected. Press the Fn

and Display Select buttons to determine whether the

pen tablet PC display screen is selected.

• The video timeout may have expired. Tap on the

display screen to reactivate the display. Note that this

is a normal, power-saving feature.

Cursor Is Not Tracking Pen

If the cursor on the screen appears to be misaligned with

the pen or is not accurately tracking the pen, calibrate

the pen. See “To Calibrate the Pen” on page 23 for more

information.

Infrared Data Transfer Is Not Working

If you are experiencing problems transferring data over

the system’s infrared interface, note the following:

• Can the IrDA port on the pen tablet PC “see” the

CAUTION

The Stylistic ST4000P Series pen tablet PC is not

waterproof. Do not pour liquids on the pen tablet PC or

wash the pen tablet PC with a heavily soaked cloth.

Alb_UG.book Page 30 Friday, November 1, 2002 4:22 PM

Care and Maintenance

IrDA port on the other device? A direct line-of-sight

path must exist between the IrDA port on the pen

tablet PC and the IrDA port on the other device.

• The distance between the two devices must not be

more than 3 feet.

• The viewing angle from the IrDA port on the pen

tablet PC must not be more than 15 degrees from a

center line between the IrDA port on the pen tablet

PC and the IrDA port on the other device.

• The device with which you are trying to communicate

must be compliant with the IrDA Standard Revision

1.1 (or 1.0).

• It may be necessary for both computers to be using

the same network connection protocols.

Pen Tablet PC is Not Responding to the Pen

If the pen tablet PC does not respond to the pen, connect

an external keyboard to the system to see if it responds to

keyboard commands. If the system doesn’t respond to a

keyboard, the application or system may have crashed,

and it may be necessary to reset the system. If the system

responds to a keyboard but not to a pen, contact your

local help desk or reseller for further assistance.

Speaker/Headphone Volume Too Low

If the audio volume on your pen tablet PC speaker or

external headphones is too low, check the following:

• Ensure that the speaker (or headphone output if using

headphones) is enabled. To do so, open the Control

Panel and double-click on the Sounds and Audio

Devices icon. Select the proper tab, and increase the

volume using the slider bar. (If you aren’t getting any

sound, uncheck the Mute box if it is checked.)

•Press the Fn button twice to open the Fujitsu menu.

Volume can be adjusted from the menu.

• Ensure that the mute box in the system volume

control (accessible from the system tray) is not set.

• Ensure that any volume control in your audio

software is set to an audible level.

Configuring Peripheral Interfaces

Certain peripheral devices can be disabled during the

BIOS Setup. If the peripheral interface you want to use

does not appear to be working with your peripheral

device, ensure that it is enabled in the BIOS. Contact

your local help desk or reseller if you need assistance

using BIOS Setup.

Alb_UG.book Page 31 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Three

Alb_UG.book Page 32 Friday, November 1, 2002 4:22 PM

Specifications

Alb_UG.book Page 33 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Four

Alb_UG.book Page 34 Friday, November 1, 2002 4:22 PM

System Specifications

Stylistic ST4000P Series Hardware Specifications

The following table provides general hardware

specifications of the Stylistic ST4000P Series pen tablet

PC by category.

Stylistic ST4000P Specifications

Physical Specifications 3

Dimensions 11.86” w x 8.66” d x 0.82”-0.88” h

(301.3mm x 220mm x 20.9-22.3mm)

Weight 3.2 lbs. (1.45 Kg)

Processing Specifications 3

CPU Ultra low voltage Mobile Intel Pentium

III processor - M with SpeedStep

technology*

Chip set Intel 830MG - 133 MHz

Processor

Speed

800 MHz*

Memory/Storage Specifications 3

Main RAM • 256MB SDRAM (on-board/

PC133).

• 144-pin SO DIMM modules

256MB and 512MB module

configurations available, with a system

maximum of 768MB.

L1 cache

(CPU)

32 KB on-die

L2 cache 512 KB on-die

BIOS ROM 8 Mbit (FWH)

Hard disk

drive

• 2.5” HDD

• Minimum 20GB IDE HDD*

• Ultra DMA 100

• Shock-mounted

Display Specifications 3

Display • Color LCD

• Passive Touch Panel

• 16-bit color

• 10.4” TFT XGA (1024 x 768), 260K

colors

• Brightness: 8 levels

• Viewing Angle:

Horizontal: 30 degrees (min.)

Vertical: 10 degrees (min.)

• Contrast Ratio:

Typ. 250, Min. 100

VRAM Intel 830MG chipset with 8MB shared

memory using Unified Memory

Architecture (UMA) delivers low-

power, high-performance 3D/2D

graphics, video, and display capabilities.

Dynamic Video Memory Technology

(DVMT) dynamically responds to

application requirements and efficiently

allocates the proper amount of memory

(48MB max.) for optimal graphics and

system performance.

Interface Specifications 3

PC Card

Slots

• One Type I or Type II

• PCMCIA CardBus version 3.0

Integrated

Interfaces

• Modem (RJ-11)

• LAN (RJ-45)

• IEEE 1394 (S400 4-pin)

•USB (Qty. 2)

•DC-In

• 15-pin D-SUB connector for

external VGA monitor

• Docking connector

Infrared IrDA version 1.1 (FIR, 4Mbps)

Stylistic ST4000P Specifications (Continued)

Alb_UG.book Page 35 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Four

Keyboard/

Mouse

support

• Keyboard/Mouse IR Port

• System IR Port

Audio • SigmaTel STAC9767 codec

• Internal mono microphone and

speaker

• Mono microphone and headphone

jacks

User

Controls

• Application Buttons, with primary,

secondary, and tertiary functions

• Power On/Suspend/Resume

button

• Emergency Shutoff Button (Power

Off button)

• Two Navigation buttons

Status

Indicators

(LEDs)

• Power

• Charge/DC-In

• Battery level

• HDD

•Hovering

* The specifications for your particular model may vary.

To determine the specifications for your system, please

visit our web site at: www.fujitsupc.com.

Power Specifications 3

Main Battery • 6-cell

• Removable, Lithium ion

• 10.8 V @ 4000 mAh

• Warm-swappable

•Recharge Time:

Suspend/Off: 3.5 hours (90%), 4.5

hours (100%)

Operating: 8 hours (100%)

• Life: Up to 5 hours. (Battery life is

dependent upon the operating

system, power management, and

applications in use.)

• Suspend Life: Minimum 5 days

Off State: Approximately 30 days

Stylistic ST4000P Specifications (Continued)

Bridge

Battery

• 6-cell NiMH, 35 mAh

• Life (with Suspend-to-RAM on

bridge battery only):

5 minutes from full charge

AC Adapter • Autosensing 100 - 240V, supplying

16 VDC, with a current of 3.75 A

Environmental Specifications 3

Temperature Operating: 41o - 95o F (5o - 35o C)

Non-operational: 5o - 140o F

(-15o - 60o C)

Humidity Operating: 20 - 85% non-condensing

Non-operating: 8 - 85% non-

condensing

Agency Approval Specifications 3

Emissions

• EN55022 (CISPR22) Class B

• FCC 15, Class B

• FCC 15C, 15.247

•DOC Class B

• ETSI EN 300-328

• ICES-003

• Canada RSS-210

Immunity

• EN55024 (1998)

• ETSI EN 301-489-17 V.1.1.1

(2000-9)

Safety

• UL and cUL Listed, UL 1950, 3rd

edition

• TuV T-Mark, EN60950

Telecom • FCC Part 68

• IC CS-03

Additional Specifications 3

Operating

systems •Microsoft

 Windows 2000

Professional

• Microsoft Windows XP

Professional

Stylistic ST4000P Specifications (Continued)

Alb_UG.book Page 36 Friday, November 1, 2002 4:22 PM

Agency Notices

Alb_UG.book Page 37 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Five

Alb_UG.book Page 38 Friday, November 1, 2002 4:22 PM

Agency Notices

Regulatory Information

NOTICE

Changes or modifications not expressly approved by

Fujitsu could void this user’s authority to operate the

equipment.

FCC NOTICES

Notice to Users of Radios and Television

These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a partic-

ular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

■Reorient or relocate the receiving antenna.

■Increase the separation between the equipment and

receiver.

■Connect the equipment into an outlet that is on a

different circuit than the receiver.

■Consult the dealer or an experienced radio/TV

technician for help.

Shielded interconnect cables must be employed with this

equipment to ensure compliance with the pertinent RF

emission limits governing this device.

Notice to Users of the US Telephone Network

Your pen tablet PC may be supplied with an internal

modem which complies with Part 68 of the FCC rules.

On the system is a label that contains the FCC Registra-

tion Number and the Ringer Equivalence Number (REN)

for this equipment among other information. If

requested, the user must provide their telephone

company with the following information:

1. The telephone number to which the computer is

connected.

2. The Ringer Equivalence Number (REN) for this

equipment.

3. The equipment requires a standard modular jack

type USOC RJ-11C which is FCC Part 68 compliant.

4. The FCC Registration Number.

This equipment is designed to be connected to the tele-

phone network or premises wiring using a standard

modular jack type USOC RJ-11C which is FCC Part 68

compliant and a line cord between the modem and the

telephone network with a minimum of 26AWG.

The REN is used to determine the number of devices that

you may connect to your telephone line and still have all

of those devices ring when your number is called. Too

many devices on one line may result in failure to ring in

response to an incoming call. In most, but not all, areas

the sum of the RENs of all of the devices should not

exceed five (5). To be certain of the number of devices

you may connect to your line, as determined by the

RENs, contact your local

telephone company.

If this equipment causes harm to the telephone network,

your telephone company may discontinue your service

temporarily. If possible, they will notify you in advance. If

advance notice is not practical they will notify you as

soon as possible. You will also be advised of your right to

file a complaint with the FCC.

This fax modem also complies with fax branding require-

ments per FCC Part 68.

Your telephone company will probably ask you to discon-

nect this equipment from the telephone network until

the problem is corrected and you are sure that the equip-

ment is not malfunctioning. This equipment may not be

used on coin-operated telephones provided by your tele-

phone company. Connection to party lines is subject to

state tariffs. Contact your state’s public utility commis-

sion, public service commission or corporation commis-

sion for more information.

This equipment includes automatic dialing capability.

When programming and/or making test calls to

emergency numbers:

■Remain on the line and briefly explain to the

dispatcher the reason for the call.

■Perform such activities in off-peak hours, such as early

morning or late evening.

FCC rules prohibit the use of non-hearing aid compatible

telephones in the following locations or applications:

■All public or semi-public coin-operated or credit card

telephones.

■Elevators, highways, tunnels (automobile, subway, rail-

road or pedestrian) where a person with impaired

hearing might be isolated in an emergency.

■Places where telephones are specifically installed to

alert emergency authorities such as fire, police or

medical assistance personnel.

■Hospital rooms, residential health care facilities, conva-

lescent homes and prisons.

■Stores where telephones are used by patrons to

order merchandise.

CAUTION

Changes or modifications not expressly approved by

Fujitsu could void this user’s authority to operate the

equipment

Alb_UG.book Page 39 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Five

■Public transportation terminals where telephones are

used to call taxis or to reserve lodging or rental cars.

■In hotel and motel rooms as at least ten percent of the

rooms must contain hearing aid-compatible tele-

phones or jacks for plug-in hearing aid compatible

telephones which will be provided to hearing impaired

customers on request.

DOC (INDUSTRY CANADA) NOTICES

Notice to Users of Radios and Television

This Class B digital apparatus meets all requirements of

Canadian Interference-Causing Equipment Regulations.

CET appareil numérique de la class B respecte toutes les

exigence du Réglement sur le matérial brouilleur du

Canada.

Notice to Users of the Canadian Telephone Network

NOTICE: This equipment meets the applicable Industry

Canada Terminal Equipment Technical Specifications.

This is confirmed by the registration number. The

abbreviation, IC, before the registration number signi-

fies that registration was performed based on a Declara-

tion of Conformity indicating that Industry Canada

technical specifications were met. It does not imply that

Industry Canada approved the equipment.

Before connecting this equipment to a telephone line the

user should ensure that it is permissible to connect this

equipment to the local telecommunication facilities.

The user should be aware that compliance with the

certification standards does not prevent service

degradation in some situations.

Repairs to telecommunication equipment should be

made by a Canadian authorized maintenance facility.

Any repairs or alterations not expressly approved by

Fujitsu or any equipment failures may give the telecom-

munication company cause to request the user to

disconnect the equipment from the telephone line.

NOTICE: The Ringer Equivalence Number (REN) for

this terminal equipment is 0.0. The REN assigned to

each terminal equipment provides an indication of the

maximum number of terminals allowed to be connected

to a telephone interface. The termination on an interface

may consist of any combination of devices subject only

to the requirement that the sum of the Ringer Equiva-

lence Numbers of all the devices does not exceed five.

Avis Aux Utilisateurs Du Réseau

Téléphonique Canadien

AVIS: Le présent matériel est conforme aux spécifica-

tions techniques d’Industrie Canada applicables au

matériel terminal. Cette conformité est confirmée par le

numéro d’enregistrement. Le sigle IC, placé devant le

numéro d’enregistrement, signifie que l’enregistrement

s’est effectué conformément à une déclaration de

conformité et indique que les spécifications techniques

d’Industrie Canada ont été respectées. Il n’implique pas

qu’Industrie Canada a approuvé le matériel.

Avant de connecter cet équipement à une ligne télépho-

nique, l’utilisateur doit vérifier s’il est permis de

connecter cet équipement aux installations de télécom-

munications locales. L’utilisateur est averti que même la

conformité aux normes de certification ne peut dans

certains cas empêcher la dégradation du service.

Les réparations de l’équipement de télécommunications

doivent être eVectuées par un service de maintenance

agréé au Canada. Toute réparation ou modification, qui

n’est pas expressément approuvée par Fujitsu, ou toute

défaillance de l’équipement peut entraîner la compagnie

de télécommunications à exiger que l’utilisateur décon-

necte l’équipement de la ligne téléphonique.

AVIS: L’indice d’équivalence de la sonnerie (IES) du

présent matériel est de 0.0. L’IES assigné à chaque

dispositif terminal indique le nombre maximal de

terminaux qui peuvent être raccordés à une interface

téléphonique. La terminaison d’une interface peut

consister en une combinaison quelconque de dispositifs,

à la seule condition que la somme d’indices d’équiva-

lence de la sonnerie de tous les dispositifs n’excède pas 5.

CAUTION

For safety, ensure that the electrical ground of the

power utility, the telephone lines and the metallic water

pipes are connected together. Do NOT attempt to make

such connections themselves but should contact the

appropriate electric inspection authority or electrician.

This may be particularly important in rural areas.

AVERTISSEMENT

Pour assurer la sécurité, les utilisateurs doivent vérifier

que la prise de terre du service d’électricité, les lignes

télphoniques et les conduites d’eau métalliques sont

connectées ensemble. Les utilisateurs NE doivent PAS

tenter d’établir ces connexions eux-mêmes, mais

doivent contacter les services d’inspection d’installations

électriques appropriés ou un électricien. Ceci peut être

particulièrement important en régions rurales.

Alb_UG.book Page 40 Friday, November 1, 2002 4:22 PM

Agency Notices

UL Notice

This unit requires an AC adapter to operate. Use only UL

Listed Class 2 Adapters with an output rating of 16 VDC,

with a current of 3.75 A.

AC Adapter output polarity:

For Authorized Repair Technicians Only

System Disposal

In the event of system disposal, please observe the

following information regarding proper procedures in

the State of Vermont.

CAUTION

The modem-to-telephone network connection must be

a line cord using a minimum #26 AWG wire.

WARNINGS

■For continued protection against risk of fire, replace

only with the same type and rating fuse.

■Danger of explosion if Lithium (clock) battery is incor-

rectly replaced. Replace only with the same or equiva-

lent type recommended by the manufacturer. Dispose

of used batteries according to the manufacturer’s

instruction.

The liquid crystal display (LCD) lamps used in this

system contain mercury. In the event of system

disposal, be sure to follow local guidelines.

Alb_UG.book Page 41 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series User’s Guide – Section Five

Alb_UG.book Page 42 Friday, November 1, 2002 4:22 PM

Appendix

Wireless LAN* User’s Guide

* Optional device

Alb_UG.book Page 43 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

Alb_UG.book Page 44 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

FCC REGULATORY INFORMATION

Please note the following regulatory information related

to the optional wireless LAN device.

Regulatory Notes and Statements

Wireless LAN, Health and Authorization for use

Radio frequency electromagnetic energy is emitted from

Wireless LAN devices. The energy levels of these emis-

sions, however, are far much less than the electromag-

netic energy emissions from wireless devices such as

mobile phones. Wireless LAN devices are safe for use by

consumers because they operate within the guidelines

found in radio frequency safety standards and recom-

mendations. The use of Wireless LAN devices may be

restricted in some situations or environments, such as:

• On board an airplane, or

• In an explosive environment, or

• In situations where the interference risk to other

devices or services is perceived or identified as

harmful.

In cases in which the policy regarding use of Wireless

LAN devices in specific environments is not clear (e.g.,

airports, hospitals, chemical/oil/gas industrial plants,

private buildings), obtain authorization to use these

devices prior to operating the equipment.

Regulatory Information/Disclaimers

Installation and use of this Wireless LAN device must be

in strict accordance with the instructions included in the

user documentation provided with the product. Any

changes or modifications made to this device that are

not expressly approved by the manufacturer may void

the user’s authority to operate the equipment. The

manufacturer is not responsible for any radio or televi-

sion interference caused by unauthorized modification

of this device, or the substitution or attachment of

connecting cables and equipment other than those spec-

ified by the manufacturer. It is the responsibility of the

user to correct any interference caused by such unautho-

rized modification, substitution or attachment. The

manufacturer and its authorized resellers or distributors

will assume no liability for any damage or violation of

government regulations arising from failure to comply

with these guidelines.

Federal Communications Commission statement

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause interference, and, (2) This

device must accept any interference, including interfer-

ence that may cause undesired operation of this device.

FCC Interference Statement

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment gener-

ates, uses, and can radiate radio frequency energy. If not

installed and used in accordance with the instructions, it

may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is encour-

aged to try and correct the interference by one or more

of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the distance between the equipment and

the receiver.

3. Connect the equipment to an outlet on a circuit

different from the one the receiver is connected to.

4. Consult the dealer or an experienced radio/TV

technician for help.

FCC Radio Frequency Exposure statement

This Wireless LAN radio device has been evaluated

under FCC Bulletin OET 65C and found compliant with

the requirements as set forth in CFR 47 Sections 2.1091,

2.1093, and 15.247 (b) (4) addressing RF Exposure from

radio frequency devices. The radiated output power of

this Wireless LAN device is far below the FCC radio

frequency exposure limits. Nevertheless, this device shall

be used in such a manner that the potential for human

contact during normal operation is minimized. When

using this device, a certain separation distance between

antenna and nearby persons must be maintained to

ensure RF exposure compliance. In order to comply with

RF exposure limits established in the ANSI C95.1 stan-

dards, the distance between the antennas and the user

should not be less than 20 cm (8 inches).

Export restrictions

This product or software contains encryption code

which may not be exported or transferred from the US

or Canada without an approved US Department of

Commerce export license. This device complies with

Part 15 of FCC Rules., as well as ICES 003 B / NMB 003

B. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesirable oper-

ation. Modifications not expressly authorized by Fujitsu

PC Corporation may invalidate the user's right to

operate this equipment.

Alb_UG.book Page 45 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

BEFORE USING THIS DEVICE

Thank you for purchasing a Fujitsu ST4000P Series Pen

Tablet PC with the optional Integrated Wireless LAN.

This manual describes the basic operating procedures

for the Wireless LAN (referred to as the “device” in this

manual) and how to set up a wireless LAN network.

Before using this device, read this manual carefully to

ensure correct operation of the device. Keep this manual

in a safe place for reference while using the device.

Characteristics of the Device

This device consists of a wireless LAN card that is

attached to the computer via a mini-PCI slot.

The main characteristics are as follows:

■It uses the power saving communications system in

the 2.4 GHz band, and does not require any license for

radio communication.

■It uses Direct Sequence Spread Spectrum (DS-SS),

which is resistant to noise.

■This device complies with Wi-Fi, and is able to com-

municate at the maximum transfer rate of 11 Mbps.

■The maximum communication range is approxi-

mately 80 feet (25 meters) inside a building. The

range may be shorter depending upon the installation

factors, such as walls and columns.

■Unauthorized access can be prevented with the use of

SSID and encryption key.

Wireless LAN Modes Using this Device

AdHoc Mode

The “AdHoc Mode” refers to the network connecting

two computers using wireless LAN cards. This connec-

tion is called an “AdHoc network.”

Using an AdHoc network, you can obtain a network

connection easily and at a low cost.

In the AdHoc mode, you can use the function supported

by Microsoft Network, such as File and Print Sharing to

exchange files and share a printer or other peripheral

devices.

To use the AdHoc Mode, you must set the same SSID

and the same encryption key for all the computers that

are connected. All connected computers can communi-

cate with each other within the communication range.

Infrastructure Mode

If a number of computers are connected simultaneously

in the AdHoc mode, the transfer rate may be reduced,

communications may become unstable, or the network

connection could fail. This is because all wireless LAN

cards are using the same radio frequency in the network.

To improve this situation, you can use a wireless LAN

access point, which is sold separately. The wireless LAN

network is in the “Infrastructure mode” when it uses an

access point, and such a connection is called the “Infra-

structure Network.”

By using an access point, you can set and use a different

communication channel for each network group. Each

channel is given a different radio frequency, and it

eliminates the collision of communications and provides

a more stable communications environment. Infrastruc-

ture mode is most suitable when you are configuring

multiple wireless LAN networks on the same floor.

To connect a wireless LAN network to a wired LAN, you

need an access point.

How to Handle This Device

If you purchased the wireless LAN option, the Integrated

Wireless LAN device is already installed in your ST4000P

Series Pen Tablet PC. Under normal circumstances, it

should not be necessary for you to remove or re-install

it. The LAN has been configured to support the oper-

ating system with which your system shipped.

The On/Off switch located on the Wireless LAN cover

turns the device on and off. You should switch the device

off when it is not in use in order to maximize battery life.

Alb_UG.book Page 46 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

CONNECTING WINDOWS 2000 SYSTEMS

This chapter describes how to set the wireless LAN

connection for computers running Windows 2000.

Workflow

The proper setup of the wireless LAN requires several

steps which must be performed in the proper order.

Following is a general outline of the steps that must be

performed. Each step is detailed later in this procedure.

1. Setting parameters

■Setting the profile

■Setting the encryption

2. Network settings

■Setting the protocol and checking the network

■Setting file and printer sharing

■Checking the connection

Setting Parameters

1. Click [Start]-> [Settings] -> [Control Panel].

2. Double-click the [PRISM Settings] icon. The

[PRISM Wireless Settings] appears.

3. Set the profile as specified in Table 1. Ask your

network administrators to check the setting.

4. When you finish your entry, click [Apply].

Table 1: Profile Parameters

5. Click the [Encryption] tab.

6. Set the encryption items in accordance with Table 2.

■AdHoc Network: Specify the same value for all the

computers for which the encryption key is used for

connection.

■Infrastructure Network: Specify the identical encryp-

tion keys to the encryption keys set for the access

point. For instructions on how to check the encryp-

tion keys set for the access point, refer to the access

point manual.

POINT

If you pruchased a ST4000P Series Pen Tablet PC with

the wireless LAN option, the integrated wireless LAN

device and drivers have already been installed. This

procedure outlines the steps for setting the device

parameters.

Updated drivers and/or utilities may become available

after this manual is printed; see any addenda or fliers

that may be included in the system packaging.

Item Description

Profile Enter the system file name in which the

parameter information is to be saved.

Mode Ad Hoc Network: Click the down arrow

and select “802.11 AdHoc”.

Infrastructure Network: Click the down

arrow and select “Infrastructure”.

SSID Enter the network name to which you

want to connect

Transmit

Rate

Obtain the information from your

network administrator. If you do not

have a network administrator, select

“Fully Automatic”.

Power

Save

Enabled

Not supported.

AdHoc

Channel

AdHoc Network: Select the same

channel, 1-11, for all connected

computers. If there is more than one

wireless LAN nearby (such as on the

same floor), we recommend that the

channels for each LAN be 5 numbers

apart (e.g., if there are two other LANs

nearby, the channels used should be 1,

6, and 11).

Infrastructure Network: Not an option.

POINT

Make sure that you specify the encryption keys. If you

do not specify the keys, any computer with a wireless

LAN card can be connected. This presents a risk that

your data may be stolen or destroyed.

Item Description

Encryption

(WEP)

Click the down arrow and select an

encryption option.

■Disable: Disables the encryption. In

this case, “Create keys with Pass-

phrase” and subsequent items are

greyed out, and you cannot enter

anything.

■40 bit*: The encryption is set.

Select either “Create keys with

Passphrase”, “Create keys manu-

ally”, or “ASCII Input”, and enter

the encryption keys.

■104 bit*: The encryption is set.

Select either “Create keys with

Passphrase”, “Create keys manu-

ally”, or “ASCII Input”, and enter

the encryption keys.

Item Description

Alb_UG.book Page 47 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

Table 2: Encryption Key Setup

7. When you finish your entry, click [Apply].

8. Click [OK]. [PRISM Wireless Settings] closes.

You have completed the parameter settings.

* 40 bit and 104 bit encryption is the wireless LAN

equivalent of 64 bit and 128 bit encryption, as set by

Microsoft and wireless LAN manufacturers. This is the

same encryption rate that is used by the Windows XP

operating system, and was selected in order to align it

closer to the wireless LAN standard. For consistency, the

Windows 2000 utilities reflect the same modes.

Outside of wireless LAN environments, encryption is

generally set at either 64 bit or 128 bit. However, the

wireless LAN standard requires that 24 bits be reserved

for fixed data. As a result, the user can only use 40 bits

(64 minus 24) or 104 bits (128 minus 24) for encryption.

This requirement also fixes the number of characters

used for 128 bit encryption to 13 which is calculated as

(13 x 8 bits = 104).

NETWORK CONNECTION: WINDOWS 2000

The section describes how to set the network connection

for a computer with Windows 2000.

Network Settings

In this section, you set “TCP/IP Settings,” and complete

“Checking Computer Name and Workgroup,” required

for the network connection.

TCP/IP Settings

1. Click [Start] -> [Settings] -> [Control Panel].

2. Double-click the [Network and Dial-up

Connections] icon. The [Network and Dial-up

Connections] window appears.

3. Right click the [Local Area Connection], then click

[Properties] from the menu that appears. The [Local

Area Connection Properties] window appears.

4. Perform the following steps.

■Click [Internet Protocol (TCP/IP)].

■Click [Properties]. The [Internet Protocol (TCP/IP)

Properties] window appears.

Create Keys

with

Passphrase

Not supported.

Passphrase Not supported.

Create Keys

Manually

(Hexadecimal

Input)

Select this to use hexadecimal

character codes to set the encryption

keys (Keys 1 - 4).

Enter a 10-digit value when you have

selected [40 bit]* for the encryption.

Enter a 26-digit value when you have

selected [104 bit]* for encryption.

Select if the network contains a card

that is set with the encryption key

using the character code. Specify the

encryption keys with the same value

used for other wireless LAN cards

that are already set.

ASCII Input Select to use the ASCII codes to set

encryption keys (Keys 1 - 4). Select

this if network does not contain other

wireless LAN cards that are set with

encryption key using character codes.

Enter a 5-digit value when you have

selected [40 bit]* for the encryption.

Enter a 13-digit value when you have

selected [104 bit]* for encryption.

You can use the following characters:

0 - 9, A - Z, a - z, _ (underscore).

For example, to set “ABC12” for the

encryption key, enter “ABC12.”

Default Key Click the down arrow, and select a

key from Keys 1 - 4.

POINT

When using ADSL (PPPoE) with the infrastructure

network to connect to the Internet, you must change

the computer’s MTU size set. To change MTU size, refer

to the manual that comes with the access point.

Item Description

POINT

More than one network adapter is installed in your

system if more than one [Local Area Connection] entry

is displayed. In this case, select the [Local Area

Connection] entry with [Intersil PRISM Wireless LAN

PCI Card] displayed under [Device Name].

Alb_UG.book Page 48 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

5. Set an IP address as indicated in Table 3. Ask your

network administrator to check the setting.

Table 3: Setting an IP Address

6. Click [OK]. The [Local Area Connection Properties]

window appears again.

7. Click [OK]. When a message appears prompting you

to restart the computer, click [Yes].

Checking the full computer name and workgroup

1. Click [Start] -> [Settings] -> [Control Panel].

2. Double-click the [System] icon. [System Properties]

appears.

3. Click the [Network Identification] tab.

4. Check [Full computer name] and [Workgroup]. Ask

your network administrator and check the setting.

Table 4: Checking computer name and workgroup

5. Click [OK]. When a message appears prompting you

to restart the computer, click [Yes].

Sharing

In this section, you set sharing of the drive, folder, and

printer.

You only need to set this when you are sharing files or a

printer with other computers on the network.

When you share a drive, folder, or printer, you can use

them from any computer on the network.

Setting [File and Printer Sharing for Microsoft

Networks]

1. Click [Start] -> [Settings] -> [Control Panel].

2. Double-click the [Network and Dial-up

Connections] icon. The [Network and Dial-up

Connections] windows appears.

3. Right click the [Local Area Connection], then click

[Properties] from the menu that appears. [Local

Area Connection Properties] appears.

4. If [File and Printer Sharing for Microsoft Networks]

is displayed in the list, make sure that it is checked. If

it is not checked, check it and click [OK]. You do not

have to perform the following steps. Go to the next

section, entitled “Sharing Files.”

If [File and Printer Sharing for Microsoft Networks]

is not found in the list, click [Install], and perform

Step 5 and subsequent steps. When you click

[Install], the [Select Network Component Type]

window appears.

Item Description

For AdHoc

Network

Set the IP address and subnet mask:

Click [Use the following IP address],

and enter a value for [IP address] and

[Subnet mask].

Refer to “Setting IP Addresses” on

page 58 to set an IP address and

subnet mask.

For

Infrastructure

Network

Select [Obtain an IP address

automatically]:

For the DNS server, select [Obtain

DNS server address automatically].

For the IP address, DNS server, and

default gateway, follow the network

administrator's instructions, if any.

Item Description

Full

Computer

Name

A name to identify the computer on

the network. You can specify any

name to each computer.

For easier identification, use the model

name or user name.

Workgroup A name for the network group:

■AdHoc Network:

Specify the same name to all com-

puters within the same network.

■Infrastructure Network: Specify a

workgroup name to connect to.

To change the setting, click

[Properties], and follow the instruc-

tions on the screen. [System Proper-

ties] appears again.

POINT

More than one network adapter is installed in your

system if more than one [Local Area Connection] entry

is displayed. In this case, select the [Local Area Connec-

tion] entry with [Intersil PRISM Wireless LAN PCI Card]

displayed under [Device Name].

Item Description

Alb_UG.book Page 49 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

5. Perform the following steps.

■Click [Service].

■Click [Add]. The [Select Network Service] window

appears.

6. Perform the following steps.

■Click [File and Printer Sharing for Microsoft

Networks].

■Click [OK]. You will go back to [Local Area Connec-

tion Properties], and [File and Printer Sharing for

Microsoft Networks] is added to the list.

7. Click [OK].

Sharing Files

The following example shows how to set sharing the

“Work” folder on the c: drive.

1. On the desktop, double-click [My Computer]->

C: drive.

2. Right-click the “Work” folder, then click [Sharing]

from the menu. The [Work Properties] window

appears.

3. Click [Share this folder] and set necessary items, as

indicated in the following table.

Table 5: Sharing files

4. Click [OK]. The folder is set shared, and the “Work”

folder icon changes.

Printer Sharing

1. Click [Start] -> [Settings] -> [Printers]. The Printers

window appears, showing the printers that are

connected.

2. Right click the printer that you want to share, then

click [Sharing] from the menu that appears.

3. Click [Sharing], and select necessary items.

Table 6: Printer Sharing

4. Click [OK]. The printer sharing is set, and the icon

changes.

Checking the Connection

After the network setting is completed, access the shared

drive on another computer to check the connectivity of

the wireless LAN network.

Accessing Another Computer

1. Double-click the [My Network Places] icon on the

desktop. [My Network Places] appears.

2. Double-click [Computers near me]. The computers

that are connected to the network are displayed.

3. Double-click the computer that you want to access.

The drive that you set with “Sharing” are displayed.

4. Double-click the drive that you want to access. The

drive is displayed showing its contents and made

available to you. If you have any questions or prob-

lems, refer to “Troubleshooting Table” on page 55.

Checking the Connectivity

1. Click [Start] -> [Settings] -> [Control Panel].

2. Double-click the [PRISM Settings] icon. [PRISM

Wireless Settings] appears.

3. Check the connectivity on the [Link] tab. The

current condition of connection is displayed.

POINT

If you have changed the setting, [Close] is shown

instead. Click [Close].

Item Description

Share name You can specify a share name for the

drive or folder that you want to share.

Comment You can enter the description for the

drive or folder that you want to share.

User limit Specifies the limit for the number of

sharing users.

Permissions Specifies the folder access privileges.

Caching Specifies the caching for the folder.

Item Description

Not Shared Disables printer sharing.

Shared As Enables printer sharing.

Share Name Specifies a share name of the

printer to be shared.

Comment Enter the description of the printer

to be shared.

Passwords If you specify a password, you

need to enter it when using the

printer.

Alb_UG.book Page 50 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

Table 7: Checking connectivity

CONNECTING WINDOWS XP SYSTEMS

This chapter describes how to set up the wireless LAN

connection for computers that are running Windows XP.

Workflow

The proper setup of the wireless LAN connection

requires that several steps be performed in the proper

order. Following is a general outline of the steps to be

performed. Each step is detailed later in this procedure.

1. Setting parameters

■Setting the profile

■Setting the encryption

2. Network settings

■Setting the protocol and checking the network

■Setting file and printer sharing

■Checking the connection

Setting Parameters

1. Click [Start] -> [Control Panel].

2. Click [Network and Internet connections].

3. Click [Network connection]. A list of networks that

are currently installed is displayed.

4. Right click [Intersil PRISM Wireless LAN PCI Card]

in the list, and click [Properties] from the menu that

is displayed. [Wireless Network Connection Proper-

ties] appears.

5. Click the [Wireless Networks] tab. The [Wireless

Networks] tab appears.

6. Perform the following steps.

■Make sure that [Use Windows to configure my wire-

less network settings] is checked.

■Click [Add] under [Preferred networks]. [Wireless

Network Properties] appears.

7. Set parameters in accordance with Table 8.

■For the AdHoc network, specify the same value to all

the computers, for which the encryption key is used

for connection.

■For the infrastructure network, specify the encryp-

tion key (network key) with the same value to the

encryption key of the access point. For how to check

the encryption keys set for the access point, refer to

the manual supplied with the access point.

Item Description

State Shows the current condition of

connection.

The MAC address of the other

computer to which you are

connected is displayed when the

connection is successful. If you are

connected to more than one

computer, the computer that has

the best connectivity is displayed.

Current Channel Shows the current channel used

for the connection.

Current Tx Rate Shows the current transfer rate in

Mbits/sec.

[Radio Off]/

[Radio On]

Click [Radio Off] to disconnect.

Click [Radio On] to connect to the

network.

[Rescan] button Click this button to search for

others to connect to.

Throughput

(Bytes/sec)

Shows the actual transfer rate of

the data transfer for send (Tx) and

receive (Rx).

Link Quality Shows either [Excellent], [Good],

[Fair], [Poor], or [Not Connected],

depending on the link quality.

Not shown for AdHoc connection.

Signal Strength Shows either [Excellent], [Good],

[Fair], [Poor], or [Not Connected],

depending on the signal strength.

Not shown for AdHoc connection.

POINT

If you purchased a ST4000P Series Pen Tablet PC with

the wireless LAN option, the integrated wireless LAN

device and drivers have already been installed. This

procedure outlines the steps for setting the device

parameters.

Updated drivers and/or utilities may become available

after this manual is printed; see any addenda or fliers

that may be included in the system packaging.

POINT

Be sure to specify the encryption keys. If you do not

specify the keys, any computer with a wireless LAN card

can be connected. This presents a risk that other users

may steal or destroy your data.

Alb_UG.book Page 51 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

Table 8: Setting parameters

8. When you finish your entry, click [OK]. [Wireless

Network Connection 2 Properties] appears again.

9. Make sure the network name you specified for the

SSID in Step 7 is added under [Preferred networks].

Network Connection

The section describes how to set the network connection

for a computer running Windows XP.

Network Settings

In this section, you set “TCP/IP Settings,” and complete

“Checking Computer Name and Workgroup” required

for the network connection.

TCP/IP Settings

1. On [Wireless Network Connection Properties], click

[General].

2. Perform the following steps.

■Click [Internet Protocol (TCP/IP)].

■Click [Properties]. [Internet Protocol (TCP/IP)

Properties] appears.

3. Set an IP address. Ask your network administrator

and check the setting.

Table 9: Setting an IP address

5. Click [OK].

6. Close [Network Connection].

Checking the Full Computer Name and Workgroup

1. Click [Start] -> [Control Panel]. Make sure the

Classic View is selected.

2. Double-click the [System] icon. [System Properties]

appears.

3. Click the [Computer Name] tab.

Item Description

Network

Name

SSID

Enter the network name to which you

want to connect. This is a required item.

For the network name, ask your LAN

administrator.

AdHoc network: Set the same name for all

of the computers that are to be connected.

Infrastructure network: Specify the same

name as that specified on the access point

that is to be connected. For access point

instructions, refer to the manual that

comes with the access point.

Key

Format

Click the down arrow and select the input

for the Network key.

ASCII

characters

Select this when using

ASCII characters for the

Network Key. Characters

that can be used follow:

0-9, A-Z, a-z, and

_ (underscore)

Example: To set the key to

“ABC12”, input “ABC12”.

Hexa-

decimal

characters

Select this when using

hexadecimal characters for

the Network Key.

Use this if there is a wireless

LAN card in the network

that has the Network Key

set to a character code. In

’Network Key’, input the

same value as the other

wireless LAN card.

POINT

If [Wireless Network Connection 2 Properties] is not

displayed, click [Start] -> [Settings] -> [Control Panel],

and double-click the [Network Connection] icon.

Right click the [Wireless Network Connection], and

then click [Properties] from the menu that appears.

Item Description

AdHoc

Network

Set the IP address and subnet mask.

Click [Use the following IP address].

Enter a value for [IP address] and

[Subnet mask]. See “Setting IP

Addresses” on page 58 to set IP

address and subnet mask.

For

Infrastructure

Network

Select [Obtain an IP address

automatically]. For the DNS server,

select [Obtain DNS server address

automatically]. For the IP address,

DNS server, and default gateway,

follow the network administrator's

instructions, if any.

POINT

If you have changed the setting, [Close] is shown

instead. Click [Close].

Alb_UG.book Page 52 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

4. Check [Full computer name] and [Workgroup]. Ask

your network administrator and check the setting.

Table 10: Setting computer name and workgroup

To change the setting, click [Change], and follow the

instructions on the screen. [System Properties] appears

again.

5. Click [OK]. When a message appears prompting you

to restart the computer, click [Yes].

Sharing

In this section, you set sharing of the drive, folder, and

printer.

You need to set this only when you are sharing files or a

printer with other computers on the network.

When you share a drive, folder, or printer, you can use

these from any computer on the network.

Setting [File and Printer Sharing for Microsoft

Networks]

1. Click [Start] -> [Control Panel]. Make sure the

Classic View is selected.

2. Double-click the [Network Connection] icon.

3. Right click the [Wireless Network Connection], and

then click [Properties] from the menu that appears.

[Wireless Network Connection Properties] appears.

4. If [File and Printer Sharing for Microsoft Networks]

is displayed in the list:

Make sure that it is checked. If it is not checked,

check it, and click [OK]. You do not have to perform

the following steps. Go to the next section, “Sharing

Files.”

If [File and Printer Sharing for Microsoft Networks]

is not found in the list, click [Install], and perform

Step 5 and the subsequent steps. When you click

[Install], [Select Network Component Type]

appears.

5. Perform the following steps.

■Click [Service].

■Click [Add]. [Select Network Service] appears.

6. Perform the following steps.

■Click [File and Printer Sharing for Microsoft

Networks].

■Click [OK]. You will go back to [Wireless Network

Connection 2 Properties], and [File and Printer

Sharing for Microsoft Networks] is added to the list.

7. Click [Close].

Sharing Files

The following example shows how to set sharing the

“Work” folder on the c: drive.

1. Click [Start] -> [My Computer].

2. Double-click the [Local Disk (c:)] icon.

3. Right click the “Work” folder, and then click

[Sharing and Security] from the menu that appears.

[Work Properties] appears.

4. Click [If you understand the security risks but want

to share files without running the wizard, click

here].

In the [Work Properties] window, the description under

[Network Sharing and security] changes.

5. Check [Share this folder on the network].

Uncheck [Allow network users to change my files], if

the shared folder is for read only.

6. Click [OK]. The folder is set shared, and the “Work”

folder icon changes.

Printer Sharing

1. Press [Start]->[Control Panel] (or [Settings], if

viewing in Classic mode)-> [Printers and Faxes].

The Printers and Faxes display will appear and the

connected printers will be displayed.

2. Right-click the printer to be shared, and click

[Sharing] from the menu that appears. The proper-

ties of the printer to be shared will be displayed. Set

printer sharing.

On the display, the printer sharing setting is recom-

mended by the Network Setup Wizard, but for the wire-

less LAN network, security is maintained by network

name (SSID) or network key. The following steps allow

you to set up printer sharing without using the Network

Setup Wizard.

Item Description

Computer

Name

A name to identify the computer on

the network. You can specify any

name to each computer. Use up to 15

single-byte characters. For easier

identification, use the model name or

user name.

Workgroup A name of the network group. Use up

to 15 single-byte characters.

AdHoc Network: Specify the same

name to all computers within the

same network.

Infrastructure Network:

Specify workgroup name to connect

to.

POINT

If you have already clicked [If you understand the

security risks but want to share files without running the

wizard, click here], this window does not appear.

Alb_UG.book Page 53 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

3. Click 'If you understand the security risks but want

to share printers without running the wizard, click

here. 'Enable Printer Sharing' will be displayed.

4. Select 'Just enable printer sharing'.

5. Click 'OK'. The printer properties will be indicated.

6. Select 'Share this printer'.

7. Enter the sharing printer name in 'Share name'.

8. Click OK. The printer will be shared, and the printer

icon will become a sharing icon.

Checking the Connection

After the network setting is completed, access the shared

drive on another computer to check the connectivity of

the wireless LAN network.

Accessing Another Computer

1. Click [Start] -> [My Computer].

2. From the left menu in [Other Places], click [My

Network Places].

3. From the left menu in [Network Tasks], click [View

workgroup computers]. The workgroup in which

you are participating will appear.

4. Double click the computer to which you want to

connect. The drive that you set in [Computer

Sharing] appears.

5. Double click the drive to which you want to connect.

The contents of the drive will appear, and is available

for use.

If you have a question or problem, refer to “Trouble-

shooting Table” on page 55.

Checking the Connectivity

1. Click [Start] -> [Control Panel].

2. Double-click the [PRISM Settings] icon. [PRISM

Wireless Setting] appears.

3. Check the connectivity on the [Link] tab. The

current condition of connection is displayed

Table 11: Checking connectivity

Item Description

State Shows the current condition of

connection.

The MAC address of the other

computer that you are connected to is

displayed, when the connection is

successfully made. If you are

connected to more than one

computer, the computer that has the

best connectivity is displayed.

Current

Channel

Shows the current channel used for

the connection.

Current Tx

Rate

Shows the current transfer rate in

Mbits/sec.

Radio Off/

Radio On

Click [Radio OFF] to disconnect.

Click [Radio On] to connect to the

network.

Rescan Click this button to search for others

to connect to.

Throughput

(Bytes/sec)

Shows the actual transfer rate of the

transfer data for send (Tx) and receive

(Rx).

Link Quality Shows the link quality. This is not

shown for the AdHoc connection.

Signal

Strength

Shows the signal strength.

This is not shown for the AdHoc

connection.

Item Description

Alb_UG.book Page 54 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

TROUBLESHOOTING

This section contains troubleshooting information, including causes and actions, for problems you may find while using

this device.

Troubleshooting Table

Problem Possible Cause Possible Solution

An exclamation mark

(!) or cross (x) is

attached to [Intersil

PRISM Wireless LAN

PCI Card].

A failure to

recognize the device.

Restart the computer.

A failure in installing

the driver.

Restart the computer.

Other computers are

not displayed when

the [Network

Computer] icon is

double-clicked.

The network has not

been set up correctly.

Check the setting for the protocol, workgroup, and sharing.

To check this, you need a different procedure, depending upon the

operating system that you use. Refer to the appropriate section of

this chapter.

It takes time before

the network is

searched and the

computer connected

is displayed.

Perform the following steps to search for the computer.

■Click [Start] -> [Search] -> [Other Computers].

■Enter the computer name that you are connecting to in [Name],

and click [Search].

■Double-click the icon of the computer that has been searched.

A failure in installing

the driver.

Make sure that the driver is correctly installed.

The TCP/IP protocol

is not installed, or,

the IP address is not

set correctly.

Make sure that the TCP/IP protocol is installed. To check this, you

need a different procedure, depending on the operating system that

you use. Refer to the appropriate section of this manual.

The TCP/IP protocol

is not installed, or,

the IP address is not

set correctly.

If the TCP/IP protocol is installed, do the following to check the IP

address:

1. Windows 2000:

Click [Start] -> [Programs] -> [Accessories] -> [Command

Prompt].

Windows XP:

Click [Start] -> [All Programs] -> [Accessories] ->

[Command Prompt].

2. Enter “IPCONFIG” command, and press [Enter].

(If your hard disk is C drive, enter

C:\>ipconfig)

Check that the IP address is correctly displayed under the IP Address.

Example:

IP address: 10.0.1.3

Subnet Mask: 255.255.255.0

Default Gateway: 10.0.1.1

No communication

due to poor radio

signal.

Shorten the distance between computers or remove visible obstacles

between them, and retry the connection.

Alb_UG.book Page 55 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

IP packet isn’t

reaching its

destination

Run the PING

command to check

the connection

Perform the following steps to run the PING command to check if the

IP packet is correctly delivered to the destination.

To run the PING command, the TCP/IP protocol must be installed.

First you will determine your IP address, then you will make sure your

IP address can respond, and then you will make sure other computers

can be addressed.

1. Windows 2000: Click [Start] -> [Programs] -> [Accessories] -

> [Command Prompt].

Windows XP: Click [Start] -> [All Programs] -> [Accessories] ->

[Command Prompt].

2. Type: ipconfig > directory\filename

where directory and filename represent the location at which

you want to store the IP address.

3. Click [Enter], then go to the location you specified above. The

IP address for your system will be contained in the file.

4. To check that your IP address is functioning properly, go back

to the DOS prompt and type: ping <IP address>, then press

[Enter]. You will receive several replies, followed by the PING

statistics (similar to below).

5. To check that your system is communicating with other

systems, go to the DOS prompt and type:

\>ping XXX.XXX.XXX.XXX. (With the destination IP address

in place of XXX.XXX.XXX.XXX).

Example: if the destination IP address is 10.0.1.3:

C:\>ping 10.0.1.3

A message similar to the following appears if the connection is

successful.

Pinging 10.0.1.3 with 32 bytes of data:

Reply from 10.0.1.3: bytes=32 time=1ms TTL=32

Reply from 10.0.1.3: bytes=32 time<10ms TTL=32

Reply from 10.0.1.3: bytes=32 time=4ms TTL=32

Reply from 10.0.1.3: bytes=32 time<10ms TTL=32

If the connection fails, [Request timed out], [Destination host

unreachable], or a similar message appears. In this case, refer to the

“Other computers are not displayed” portion of this chapter.

Cannot connect to

the network

There are several

possible causes, as

listed to the right.

Refer to the

specific section of this

manual or your user’s

manual.

The following causes are possible. Check each one of them.

■The network name or encryption key is not right.

■The driver has not correctly started.

■The destination computer is not turned on.

■You do not have the access privilege to the destination computer.

■The card has failed.

■Hardware conflict.

Problem Possible Cause Possible Solution

Alb_UG.book Page 56 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

I want to remove the

driver

(Windows 2000)

Windows 2000:

When removing the driver, make sure that the device is attached to

the computer. If you try to remove the driver while the device is

detached from the computer, the driver is not removed.

1. Right click the [My Computer] icon on the desktop, and then

click [Properties] from the menu that appears. [System Proper-

ties] appears.

2. Click the [Hardware] tab.

3. Click [Device Manager...]. The [Device Manager] window

appears.

4. Click [+] beside [Network adapters].

5. Right click [Intersil PRISM Wireless LAN PCI Card], and

click [Uninstall] from the menu that is displayed. [Confirm

Device Removal] appears.

6. Click [OK].

7. Close [System Properties]. Make sure that the icon has disap-

peared from the task tray in the lower right corner of the screen.

8. Click [Start] -> [Settings] -> [Control Panel].

9. Double-click [Add/Remove Programs]. [Add/Remove Pro-

grams] appears.

10. Perform the following steps.

■Click [PRISM 11Mbps Wireless LAN for Windows].

■Click [Change/Remove].

11. A window appears asking you if you really want to remove the

driver.

12. Click [Yes]. When the driver is removed, a window appears

showing that the driver has been removed.

13. Click [OK].

14. Close [Add/Remove Programs] and [Control Panel].

15. Shut down Windows, and turn off the computer.

Problem Possible Cause Possible Solution

Alb_UG.book Page 57 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

ABOUT IP ADDRESSES

Setting IP Addresses

If you are not sure how to set the IP address, refer to the

following procedure.

If you have an access point (DHCP server) on the

network, set the IP address as follows:

Windows 2000: [Obtain an IP address automatically]

Windows XP: [Obtain an IP address automatically]

If the IP address is already assigned to the computer in

the network, ask the network administrator to check the

IP address to be set for the computer.

If no access point is found in the network:

An IP address is expressed with four values in the range

between 1 and 255.

Set the each computer as follows: The value in paren-

theses is a subnet mask.

Computer A: 192.168.100.2 (255.255.255.0)

Computer B: 192.168.100.3 (255.255.255.0)

Computer C: 192.168.100.4 (255.255.255.0)

Computer X: 192.168.100.254 (255.255.255.0)

Problem Possible Cause Possible Solution

I want to remove

the driver

(Windows XP)

Windows XP:

When removing the driver, make sure that the device is attached to

the computer. If you try to remove the driver while the device is

detached from the computer, the driver is not removed.

1. Click [Start], right click [My Computer], and then click [Proper-

ties] from the menu that appears. [System Properties] appears.

2. Click the [Hardware] tab.

3. Click [Device Manager].

4. Click [+] beside [Network adapters].

5. Right click [Intersil PRISM Wireless LAN PCI Card], and

click [Uninstall] from the menu that is displayed. [Confirm

Device Removal] appears.

6. Click [OK].

7. Close [System Properties].

8. Make sure that the icon has disappeared from the task tray in

the lower right corner of the screen.

9. Click [Start] -> [Control Panel]. [Control Panel] appears.

10. Double-click [Add/Remove Programs]. [Add/Remove Pro-

grams] appears.

11. Perform the following steps.

■Click [PRISM 11Mbps Wireless LAN for Windows].

■Click [Change/Remove].

A window appears asking you if you really want to remove

the driver.

12. Click [Yes]. When the driver is removed, a window appears

showing that the driver has been removed.

13. Click [OK].

14. Close [Add/Remove Programs] and [Control Panel].

15. Shut down Windows, and turn off the computer.

POINT

A DHCP server is a server that automatically assigns IP

addresses to computers or other devices in the network.

There is no DHCP server for the AdHoc network.

Alb_UG.book Page 58 Friday, November 1, 2002 4:22 PM

Wireless LAN User’s Guide

SPECIFICATIONS

Technical Specifications for Integrated Wireless LAN Device

Item Description

Network Type IEEE 802.11b

Transfer Rate 11/5.5/2/1Mbps (auto change)

Frequency Range 2,412 - 2,462 MHz

Channels One of 11 channels is used

Card Type Non-intelligent

VCC Class B

Security Network name, encryption key

Supported Operating Systems Windows 2000 Professional, Windows XP Professional

Power Current Max: 350mA

Maximum number of units recommended for

wireless LAN (AdHoc network)

10 or less

Alb_UG.book Page 59 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series Pen Tablet PC User’s Guide – Appendix

Alb_UG.book Page 60 Friday, November 1, 2002 4:22 PM

Index

air flow vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 6, 7

Application Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

application buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

application A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

application B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Ctl-Alt-Del button . . . . . . . . . . . . . . . . . . . . . . . . . 10

Enter button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Escape button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Function button . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

hovering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

orientation button . . . . . . . . . . . . . . . . . . . . . . . . . 10

right-click button . . . . . . . . . . . . . . . . . . . . . . . . . . 10

tertiary functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

battery gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

battery gauge icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

battery pack

charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

charging times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

critically low level . . . . . . . . . . . . . . . . . . . . . . . . . . 21

low-battery warning . . . . . . . . . . . . . . . . . . . . . . . . 21

no memory effect . . . . . . . . . . . . . . . . . . . . . . . . . . 23

overcharge protection . . . . . . . . . . . . . . . . . . . . . . . 23

removing and installing . . . . . . . . . . . . . . . . . . . . . 24

will not begin charging . . . . . . . . . . . . . . . . . . . . . . 23

battery power

conserving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

used in suspend-to-RAM mode . . . . . . . . . . . . . . . 21

battery release button . . . . . . . . . . . . . . . . . . . . . . . . . . 4

battery release latch . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

application buttons, for . . . . . . . . . . . . . . . . . . . . . 13

bridge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Built-in Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

calibrating the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 29

Charge/DC input icon . . . . . . . . . . . . . . . . . . . . . . . . . 8

charging the battery pack . . . . . . . . . . . . . . . . . . . . . . 23

cleaning the display screen . . . . . . . . . . . . . . . . . . . . . .30

configuring peripherals interface . . . . . . . . . . . . . . . .31

connectors and peripheral interfaces . . . . . . . . . . . . .14

conserving battery power . . . . . . . . . . . . . . . . . . . . . . .24

Conventions Used in the Guide . . . . . . . . . . . . . . . . . .v

critically low battery level . . . . . . . . . . . . . . . . . . . . . . .21

cursor

not tracking pen . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

DC in connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

DC power connector . . . . . . . . . . . . . . . . . . . . . . . . . . .6

DIMM card, removing . . . . . . . . . . . . . . . . . . . . . . . . .26

display

screen is blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

screen, cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

External Monitor Connector . . . . . . . . . . . . . . . . . . . . .6

Fujitsu Online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Fujitsu PC Contact Information . . . . . . . . . . . . . . . . . .v

hard disk drive access icon . . . . . . . . . . . . . . . . . . . . . . .9

HDD cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

headphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Hibernate (Save-to-Disk) mode . . . . . . . . . . . . . .21, 22

Hibernate mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

hovering mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

hovering mode icon . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

idle state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

IEEE 1394 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

infrared data transfer not working . . . . . . . . . . . . . . .30

Alb_UG.book Page 61 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series

infrared keyboard port . . . . . . . . . . . . . . . . . . . . . . 3, 14

infrared keyboard/mouse port . . . . . . . . . . . . . . . . . . . 7

interfaces

connectors and peripherals . . . . . . . . . . . . . . . . . . 14

IrDA port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

IrDA/FIR port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Kensington lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Kensington lock slot . . . . . . . . . . . . . . . . . . . . . . . . . . 14

LAN jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Local Area Network (LAN) . . . . . . . . . . . . . . . . . . . . 15

low-battery warning . . . . . . . . . . . . . . . . . . . . . . . . . . 21

memory cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

microphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Navigation buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

navigation buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20

optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Additional Accessories . . . . . . . . . . . . . . . . . . . . . . . 2

Carrying Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Docking Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Storage Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

overheating, avoiding . . . . . . . . . . . . . . . . . . . . . . . . . 30

Page Up/ Page Down . . . . . . . . . . . . . . . . . . . . . . . . . .15

PC Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 14, 25

Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5, 7

pen

not responding . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

peripheral connectors . . . . . . . . . . . . . . . . . . . . . . . . . .14

power icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 20

blinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20, 21

not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Power On/Suspend/Resume

button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

power usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

powering up the pen tablet . . . . . . . . . . . . . . . . . . . . .20

problems, solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

protecting the display screen . . . . . . . . . . . . . . . . . . . .29

Removable battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

removing a DIMM card . . . . . . . . . . . . . . . . . . . . . . . .26

resuming system operation . . . . . . . . . . . . . . . . . .22, 30

RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Save-to-Disk mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

shutting down the system . . . . . . . . . . . . . . . . . . . . . .20

solving problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

speaker/headphone volume too low . . . . . . . . . . . . . .31

status display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Charge/DC input icon . . . . . . . . . . . . . . . . . . . . . . . .8

hard disk drive access icon . . . . . . . . . . . . . . . . . . . . .9

power icon, blinking . . . . . . . . . . . . . . . . . . . . . . . . .20

power icon, system states indicated by . . . . . . . .8, 20

storing the system unit . . . . . . . . . . . . . . . . . . . . . . . . .30

Stylistic ST4000P

accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Alb_UG.book Page 62 Friday, November 1, 2002 4:22 PM

Index

care and maintenance . . . . . . . . . . . . . . . . . . . . . . . 29

features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4, 5, 6, 7

items included with . . . . . . . . . . . . . . . . . . . . . . . . . . 1

storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Stylistic ST4000P Specifications

additional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

agency approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Display Specifications . . . . . . . . . . . . . . . . . . . . . . . 35

environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Memory/Storage Specifications . . . . . . . . . . . . . . . 35

Physical Specifications . . . . . . . . . . . . . . . . . . . . . . 35

power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Processing Specifications . . . . . . . . . . . . . . . . . . . . 35

suspend mode, determining . . . . . . . . . . . . . . . . . . . . 21

Suspend/Resume

disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Suspend/Resume button . . . . . . . . . . . . . . . . . . . . . . . 15

suspending system operation . . . . . . . . . . . . . . . . . . . 20

Suspend-to-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 22

system interface connector . . . . . . . . . . . . . . . . . . . . . . 4

system states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 20

Hibernate (Save-to-Disk) . . . . . . . . . . . . . . . . . . . . 19

Idle state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

On state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Suspend-to-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . 19

system status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

system will not resume operation . . . . . . . . . . . . . . . 30

Tablet Dock latch point . . . . . . . . . . . . . . . . . . . . . . 4, 7

Tablet Dock port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

tertiary functions of application buttons . . . . . . . . . .13

Thermal Suede . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

turning off the system . . . . . . . . . . . . . . . . . . . . . . . . . .20

Universal Serial Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

USB port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

USB Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . .v

Windows 2000 Professional . . . . . . . . . . . . . . . . . . . .v, 1

Windows XP Professional . . . . . . . . . . . . . . . . . . . . .v, 1

Wireless LAN

before using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Connecting Windows 98/2000 Systems . . . . . . . . .47

Connecting Windows XP Systems . . . . . . . . . . . . .51

modes

Ad Hoc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . .46

Network Connection

Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . .48

Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Wireless LAN module . . . . . . . . . . . . . . . . . . . . . . . . . .4

Wireless LAN On/Off switch . . . . . . . . . . . . . . . . . . . . .4

Alb_UG.book Page 63 Friday, November 1, 2002 4:22 PM

Stylistic ST4000P Series

Alb_UG.book Page 64 Friday, November 1, 2002 4:22 PM

Fujitsu Stylistic St4000P Users Manual Alb_UG

STYLISTIC ST4000P Alb_UG-Passive-B

Navigation menu

Versions of this User Manual:

Views

Navigation