Furman Sound Ps 8 Users Manual 8, 8R Instr Sheet Rev 5

PS-8E to the manual c212d778-7aa4-42b8-91ee-7acd1f45948c

2015-02-09

: Furman-Sound Furman-Sound-Ps-8-Users-Manual-552756 furman-sound-ps-8-users-manual-552756 furman-sound pdf

Open the PDF directly: View PDF .
Page Count: 4

Introduction

Congratulations on your purchase of a Furman PS-8 Power

Sequencer, a well-designed, reliable, and simple to use product

that will help you avoid many headaches involved in installing a

rack full of complex equipment.

The PS-8 Power Sequencer is needed whenever various

kinds of equipment must be powered up or down in groups, rather

than all simultaneously. In audio systems, sequenced powering is

often necessary to allow turn-on transients from low level

amplifiers and processors to settle down before any power amps

are turned on, because simultaneous powering would result in a

loud, annoying, and potentially destructive “pop” reaching the

speakers. And in any large system whose components present

an inductive load to the AC line (including electric motors, power

supplies, and power amplifiers of all kinds), sequenced powering

can avoid excessive inrush currents that cause circuit breakers to

trip even though the steady-state currents are not excessive.

5-9927 960032-1051

Furman Sound, Inc.

1997 South McDowell Blvd.

Petaluma, California 94954-6919 USA

Phone: 707-763-1010 • Fax: 707-763-1310

www.furmansound.com

E-mail: info@furmansound.com

PS-8 Features

●Power-up in three delayed outlet groups

●Power-down reverses sequence

●Triple-mode varistor spike and surge suppression

●RFI filtering with multi-stage pi filter

●Power Status LED’s indicate which outlet groups have power

●Mains Wiring indicators monitor wiring integrity, show Normal

and five kinds of faults

●Rated 15 amps

●Remote option allows turn-on and turn-off at a distance

simply by connecting a momentary or maintained-contact

switch (and LED if desired)

●Multiple units may be linked to handle higher currents and/or

more than three delay groups

●Three pairs of switched outlets on rear panel

●Three unswitched outlets (one front, two rear)

●Circuit breaker

●Ten foot heavy duty A.C. cord

●Three year limited warranty

Power Sequencer

Instruction Sheet

MODELS PS-8, PS-8R, PS-8E and PS-8RE

Power Sequencing Features

Using the PS-8 is a simple and inexpensive way to apply and

remove power in a controlled, repeatable, foolproof 3-step

sequence. It is ideal when large installations must be switched by

inexperienced personnel.

The PS-8 provides three outlet pairs labeled Delay 1, Delay 2,

and Delay 3, that receive power approximately 1/2, 5, and 10

seconds, respectively, after the front panel switch is thrown to “ON.”

When thrown to “OFF,” the sequence is reversed, with Delay 3

losing power after approximately 1/2 second, Delay 2 after 5

seconds, and Delay 1 after 10 seconds. See the rear panel

illustration on the next page. The turn-on delay intervals are factory

preset at these durations, but may be altered by means of an

internal trimpot adjustment (see “Adjusting the Delay Intervals”

below for details). In addition to the delayed outlets, a single front

panel outlet and a rear panel pair are unswitched. Power is available

at the unswitched outlets regardless of the position of the front

panel (or remote) switch. All rear panel outlets are standard 120V,

15A duplex types. Isolated-ground “Super Spec” outlets are

available by special order.

In the event of a power out, of course all equipment plugged

into a PS-8 will lose power simultaneously. However, when power

is restored, the delayed outlet groups will again turn on in the

usual delayed sequence.

We recommend that power amps receive power last —

plug them all into Delay 3 or divide them into two groups and plug

one group into Delay 2 and the other into Delay 3. Low level equip-

ment such as mixers and signal processors should use Delay 1.

Equipment incorporating clocks or timers such as VCR’s, or

equipment that must respond to wireless remote actuation should

use the unswitched outlets. We suggest keeping the front panel

unswitched outlet free for equipment that is only in use temporarily.

The overall capacity of the PS-8 is 15 amps. This refers to the

combined steady-state current drawn by all devices plugged into

all of its nine outlets. If this combined current level exceeds 15

amps at any time, the circuit breaker will trip, cutting off power to

your rack. If this occurs, you must reduce the load by unplugging

one or more units from the PS-8. Then push the white button on

CLASS 1

WIRING

AVIS:

RISQUE DE CHOC

ELECTRIQUE—NE

PAS OUVRIR

15A

LOAD

MAX

120 VAC

60 HZ

15A

LISTED

7Z37

PROFESSIONAL

AUDIO EQUIPMENT

UNSWITCHED DELAY 1 DELAY 2 DELAY 3

+12V

STATUS

REM IN

RISK OF ELECTRIC

SHOCK. DO NOT

OPEN. REFER

SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

TO REDUCE THE

RISK OF FIRE OR

ELECTRIC SHOCK

DO NOT EXPOSE

THIS EQUIPMENT TO

RAIN AND MOISTURE.

CAUTION!

GND

120 VAC

60 HZ

Model PS-8R is shown. Model PS-8 is similar except the barrier terminal strip at right is not present.

Note: “The switch” referred to in this chart is either the front panel switch or, if used, the remote switch connected to the terminal strip of a PS-8R.

ON POWER UP:

ON POWER DOWN: Same as above.

This pair of outlets

plus the one on the

front panel are on

regardless of the

switch position.

This pair of outlets

goes off approx. 10

seconds after the

switch is turned off.

This pair of outlets

comes on approx.

1/2 second after the

switch is turned on.

This pair of outlets

goes off approx. 5

seconds after the

switch is turned off.

This pair of outlets

comes on approx. 5

seconds after the

switch is turned on.

This pair of outlets

goes off approx. 1/2

second after the

switch is turned off.

This pair of outlets

comes on approx. 10

seconds after the

switch is turned on.

Rear Panel Outlets

the circuit breaker (on the rear panel) down and in to reset it.

Although 15 amps is an absolute limit, the PS-8’s power

sequencing capability will allow you to come as close as possible

to using the full 15 amps, because the risk of tripping the breaker

is greatly reduced. This is because the PS-8 handles large but

temporary inrush currents in stages, rather than simultaneously,

allowing each stage to settle to its steady-state current draw

before the next stage is powered.

Power Conditioning Features

The PS-8 offers all basic power conditioning features besides

its sequencing capability. It provides varistor spike and surge

protection across all three modes (line to neutral, line to ground,

and neutral to ground), responding in nanoseconds to clamp

excessive transient voltages to safe levels. There is also a

sophisticated multi-stage filter for blocking radio frequency line

noise. The filter works to prevent noise from fluorescent lights,

certain dimmers, radio transmitters, and similar sources of

“electronic pollution” from leaking from the AC line into sensitive

audio, video, or computer circuits. Clean, filtered power is

provided at all 9 outlets, even the unswitched ones.

Despite its many protective features, you should be aware that

the PS-8 does not compensate if the AC line voltage itself is high

or low (i.e., it does not compensate for brownout conditions). If

you frequently move your rack to different locations, derive power

from generators, use long extension cords, travel internationally,

or are in an area particularly prone to brownouts, you may benefit

from the use of one of Furman’s AC Line Voltage Regulators in

addition to the PS-8. If you do use a voltage regulator, run the raw

power line into the regulator first so that the PS-8 receives a

stabilized voltage to distribute.

Mains Wiring Fault Analyzer

The PS-8 also assists in analyzing any faults that may occur

in the AC mains wiring. Two green and one red neon indicators

light in a specific pattern for normal wiring and in different

patterns for various faults. When the AC wiring is correct, both

green indicators will be lit, but not the red indicator. If any other

pattern of indicators is lit, a fault is present. The chart next to the

indicators identifies its exact nature. Since any wiring fault

presents a potentially serious safety hazard, the assistance of a

qualified electrician should be obtained in correcting the problem.

Adjusting the Delay Interval

The delay interval (the time between the turn-on or turn-off of

outlets 1 and 2, or 2 and 3 — not 1 and 3) is factory preset at

approximately 5 seconds. It is possible to lengthen or shorten the

delay interval by making an internal adjustment to the PS-8.

However, due to the risk of electric shock, this procedure should

only be done by a qualified technician.

Unplug the PS-8 and remove its top cover by unscrewing the

four screws that secure it. The delay adjustment is Trimpot VR1,

located on the printed circuit board near the front left corner. It is

the only trimpot on the board. It is equipped with a thumbwheel for

easy adjustment. The range of adjustment of the delay

interval is from a minimum of about 1 second to a maximum of

about 7 seconds.

220/240V Versions (Units with E Suffix Only)

Models PS-8E and PS-8RE are intended for use in countries

with nominal 220 to 240 volt AC lines. They are identical

to the PS-8 and PS-8R except their rear panel outlets are the

internationally-accepted IEC-320 connectors. They are rated at

10 amps.

Remote Switching (Units with “R” Suffix Only*)

*Momentary mode switching is not available in PS-8R’s with serial numbers below H12757.

Model PS-8R and PS-8RE differ from the corresponding

models without the “R” suffix in the addition of a barrier terminal

strip on the rear panel that allows a switch to be connected to turn

the unit on and off at a distance, and also in the START ON-OFF

SEQUENCE pushbutton on the front panel.

In the most basic configuration, only two Class 1 wires and an

SPST switch are needed to initiate an ON or OFF sequence. The

switch may be either a momentary or maintained-contact type. If

a third wire is used, an LED may also be installed at the remote

end to indicate that the power is on.

Maintained vs. Momentary Contact Switching

Maintained switches, such as most toggle switches and

push-on/push-off button switches (including the Furman RS-1),

stay open until thrown, then stay closed until thrown again.

Momentary switches, usually pushbutton types like the Furman

RS-2, are normally open and stay closed only as long as the button

is pressed. An on-off switch of either kind may be used to actuate

the PS-8’s remote operation.

Maintained switches are generally most convenient when there

is only one remote location. When more than one switch location

is required, momentary switches allow the sequence to be started

from any location.

PS-8R units come factory-set for maintained operation. They

may be easily converted to momentary operation by moving

a jumper plug on the PS-8R’s circuit board. To do this:

1. Disconnect the unit from AC power.

2. Remove the four screws that secure the top cover.

3. In the rear left corner of the circuit board, there is an area

labeled “REMOTE CONTROL.” There are two pairs of terminals

in this area, one labeled “MAINTAINED” and the other

“MOMENTARY.” There is a small black jumper linking the

MAINTAINED terminals. Slide it up and off, and replace

itsecurely over the MOMENTARY terminals.

4. Reattach the top cover.

Maintained Mode

A simple connection of the REM IN terminal to the +12V

terminal initiates an OFF sequence. Disconnecting it initiates an

ON sequence. If the cable run is long, it is recommended that the

REM IN wire be tied to the PS-8R’s GND terminal during ON op-

eration rather than leaving it floating. This will require the use of a

third conductor and a double-throw switch.

The STATUS terminal is an output that may be used to

illuminate an LED at the remote location to indicate that power is

available at the PowerPort’s outlets. If it is high (+5V), the unit is

ON (or at least in the process of sequencing ON); if low, the unit is

OFF (or sequencing OFF). Simply connect the indicator LED

between STATUS and ground (do not use a series resistor). If the

LED does not light when the switch is in the ON position, check

the polarity and reverse the LED leads (if it is wrong). If a Furman

RS-1 is the controlling switch, contact Furman’s Tech Support de-

partment for the proper wiring diagrams.

In Maintained Mode, DO NOT USE the “START ON-OFF SE-

QUENCE” switch on the front panel. If you do, you may

activate an unintended partial turn-off sequence.

Momentary Mode

In Momentary Mode, the PS-8R has "memory" — it only needs

a momentary signal from the remote switch to change its state

from ON to OFF.

When first plugged in (or after power is lost and reapplied for

any reason) the "memory" state is OFF. This means the unit will

be OFF even if the front panel on/off rocker switch is on. It will stay

off until sequenced on by a momentary connection of the REM IN

terminal to +12V. The sequence starts on the rising edge of the

signal.

The front panel START ON-OFF SEQUENCE switch is in par-

allel with, and functionally equivalent to, one or more remote mo-

mentary switches connected to the barrier strip in the rear.

The “memory” is independent of the front panel on/off rocker

switch. This means that even if the unit is sequenced OFF by the

rocker switch on the front panel, when the rocker switch is turned

back on the unit will sequence back on — it will not be necessary

to push the START ON-OFF SEQUENCE button again. The unit

“remembers” its state until the incoming power is lost, which would

then default back to OFF.

The front panel rocker is not the primary means of control in

momentary mode, and should normally be left ON. It may be

a useful secondary means of control in the rare case of having

several PS-8R’s in parallel, if there is some reason to shut down

one unit without affecting the others.

Because it is a maintained-contact switch, the RS-1 is not an

appropriate remote switch for the PS-8R when it is in momentary

mode. The momentary-contact RS-2 would be the correct choice.

Multiple Units

You can use more than one PS-8R to handle loads that ex-

ceed 15 amps. The power input for each PS-8R should come from

a separate 15 amp AC circuit. To control PS-8R’s remotely with

one or more remote switches, connect the REM IN +12V (and

optionally GND) terminals of all units together. Be sure that the

mode (momentary or maintained) of all units is set the same. Con-

nect a single maintained switch or one or more momentary

switches to the nearest PS-8R, as discussed above. If you are

unsure whether your building wiring can accommodate multiple

fully-loaded PS-8’s or PS-8R’s, consult a qualified electrician.

If multiple PS-8R’s are controlled by one or more momentary

remote switches, they will all change state (from on to off or vice

versa) on each rising edge of the voltage on the REM IN terminal.

Any remote switch AND any of the grey pushbuttons on any unit’s

front panel will toggle all the units. The rocker switch on each unit’s

front panel will turn off any individual unit that is currently on, with-

out affecting the other units.

The STATUS lines work the same in either mode. Each

reflects the true state of the outlets of its unit, and is affected by

both the “memorized” state and by the front panel rocker switch. A

separate LED must be used to indicate the status of each PS-8R.

To take care of the case of having several PS-8R’s in parallel

that somehow get out of sync such that every time a remote

button is pushed, some units turn on and others turn off, there is

a special feature of the remote signal line:

Holding the REM line high for at least 4 seconds (whether by

an actual remote switch or by any unit's front panel switch) will

force all units to the OFF state, which will put them back in sync.

This is the only way to re-sync units other than disconnecting AC

power to all the units. Remember — operating the front panel

rocker switch does NOT affect the stored state of the unit, even

though it does temporarily turn the outputs off.

This section covers the case of multiple units in parallel

(all sequences initiate simultaneously). See “AC Relay Accessory

PS-REL” on the following page for a discussion of wiring multiple

units in series.

Three Year Limited Warranty

The Furman PS-8, PS-8E, PS-8R, and PS-8RE are warranted against

failures due to defective parts or faulty workmanship for a period of three

years after delivery to the original owner. During this period, Furman will

make any necessary repairs without charge for parts or labor. Shipping

charges to the factory or repair station must be prepaid by the owner;

return shipping charges (via UPS Ground) will be paid by Furman. This

warranty applies only to the original owner and is not transferable. Also, it

does not apply to repairs done other than by the Furman factory or its

Authorized Repair Stations.

This warranty may be cancelled by Furman at its sole discretion if the

unit has been subjected to physical abuse or has been modified in any

way without written authorization from Furman. Furman’s liability under

this warranty is limited to repair or replacement of the defective unit.

Furman will not be responsible for incidental or consequential

damages resulting from the use or misuse of its products. Some states do

not allow the exclusion of incidental or consequential damages, so the

above limitations may not apply to you. This warranty gives you specific

legal rights, and you may also have other rights which vary from state to

state.

When returning any equipment for repair, please be sure that it is

adequately packed and cushioned against damage in shipment, and that

it is insured. Warranty claims should be accompanied by a copy of the

originalpurchase invoice showing the purchase date (if a Warranty

Registration Card was mailed in at the time of purchase, this is not neces-

sary). Also, please enclose a note giving your name, address, phone

number, and a description of the problem.

Service

Before returning any equipment for repair, please be sure that it is

adequately packed and cushioned against damage in shipment, and that

it is insured. We suggest that you save the original packaging and use it

to ship the product for servicing. Also, please enclose a note giving your

name, address, phone number and a description of the problem.

NOTE: All equipment being returned for repair must have a Return

Authorization (RA) Number. To get an RA Number, please call the

Furman Service Department, (707) 763-1010 ext. 40, between 8 a.m.

and 5 p.m., U.S. Pacific Time. Please display your RA Number

prominently on the front of all packages.

Maximum load: PS-8: 15 amps (1800 watts at 120 VAC)

PS-8E: 10 amps (2300 watts at 230 VAC)

Input Voltage Range: PS-8: 85 to 135 VAC; PS-8E: 190 to 270 VAC

Mains Wiring Analyzer: Detects 1 normal mode and 5 fault modes

Delay Interval: 5 seconds (adjustable with internal trimpot)

Remote Switch Momentary or maintained action.

(PS-8R only): Screw terminals, 3 for switch, 1 additional

for optional LED (22 ga. wiring minimum).

Spike Protection Modes: Line to neutral, neutral to ground, line to ground

Spike Clamping Voltage: PS-8: TVSS rating 400V peak, L-N, N-G, L-G

(tested to UL 1449). PS-8E: 500V peak

Response Time: 1 nanosecond

Maximum Surge Current: 6,500 amps (8 x 20 ms pulse)

Maximum Spike Energy: 80 joules per mode, 240 joules total protection

(“E” versions 130 joules L-N, 160 joules N-G,

L-G, 450 joules total)

Noise Attenuation: PS-8 and PS-8R: Transverse and common modes:

20 dB at 200 kHz, rising to >40 dB, 1 to 100 MHz

Mechanical: Dimensions: 1.75" H x 19" W x 8" D.

Weight: 6 lbs (2.7 kg).

Construction: Steel chassis, zinc chromate plating;

.125" brushed and black anodized aluminum front

panel; 3 oz. copper double-sided glass epoxy printed

circuit board

Power Consumption: Switch off: 6 watts

Switch on: 8.5 watts

Safety Agency Approvals: UL, CUL, CE listed.

PS-8, PS-8R SPECIFICATIONS

The Furman PS-8 is manufactured in the U.S.A.

LISTED

7Z37

Furman Sound Ps 8 Users Manual 8, 8R Instr Sheet Rev 5

PS-8E to the manual c212d778-7aa4-42b8-91ee-7acd1f45948c

Navigation menu

Versions of this User Manual:

Views

Navigation