User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3032481 |
| Application ID | pAldzkOT4mDTkA+nA63Fug== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 124.13kB (1551624 bits) |
| Date Submitted | 2016-06-19 00:00:00 |
| Date Available | 2016-06-19 00:00:00 |
| Creation Date | 2016-04-13 10:04:13 |
| Producing Software | Corel PDF Engine Version 16.1.0.843 |
| Document Lastmod | 2016-06-08 10:07:51 |
| Document Title | 未命å -1 |
| Document Creator | CorelDRAW X6 |
| Document Author: | scb |
Wiring Diagram AV OUT AV IN SUBWOOFER OUT IR REMOTE JACK HDMI JACK AUDIO IN ANTENNA WIRING CONNECTING SOCKET Specification GENERAL Supply Voltage Current Consumption Power Output Number of channels Unit Dimensions FM SECTION Frequency range Effective sensitivity I.F Frequency AM SECTION Frequency range Effective sensitivity I.F Frequency Preamp Output USB PLAYBACK System Frequency characteristics Signal to noise (USB) DC 12V Max.5A 2x 20 W 2 STEREO channels. (L X W X H): 130X 113 X 86 (mm) 87.5Mhz - 108Mhz 87.5 Mhz - 107.9Mhz 87.5 Mhz - 108Mhz (Europe) (U.S.A.) (Australia) 3uV. 10.7MHz. 522Khz - 1620Khz 530khz - 1710Khz 522 Khz - 1710Khz (Europe) (U.S.A.) (Australia) 40dB. 450KHz 1 V Output MP3 audio system. 20Hz -100Hz <=5dB 10KHz-20KHz <=5dB. 50dB [1KHz] . WALLMOUNT Entertainment System Locations and Names of the Controls Wiring connecting socket view GREY 10 GREY/BLACK YELLOW +12V DC MEMORY B+ BLACK POWER GROUND Mounting Installation 11 12 15 16 14 17 13 18 Location * Choose a mounting location away from humid areas, water sources, appliances or any equipment that can radiate heat. * Select an area on a wall or cabinet which is free from cable, fuel or brake lines and ensure the area behind the wall mount stereo has a vent hole or if it is an enclosed box and has adequate room around the rear of the unit for cooling. * Ensure when the stereo is mounted in the cut out that the wires at the rear of the unit are not pressed against the heat sink Installing the unit. * Before finally installing the unit, connect the wiring temporarily and make sure the unit and the system work properly. *Fix the unit with screw according to following diagram. SCREW 19 20 21 1. POWER & MUTE BUTTON 2. LCD DISPLAY 3. VOLUME + BUTTON 4. VOLUME - BUTTON 5. SEL/AUX MODE BUTTON 6. AV MODE BUTTON 7. AM/FM MODE BUTTON 8. HDMI MODE BUTTON 9. USB MODE BUTTON 10. BT MODE BUTTON 11. NEXT BUTTON 12. PREVIOUS BUTTON 22 23 24 13. 1/ PLAY/PAUSE BUTTON 14. 2/STOP BUTTON 15. 3/RPT BUTTON 16. 4/RDM button 17. 5/ BACKLIGHT/HANG UP BUTTON 18. 6/CLOCK ADJUST/ALARM/TEL BUTTON 19. RESET BUTTON 20. HEADPHONE SOCKET 21. AUX IN JACK 22. HDMI IN JACK 23. MICROPHONE IN 24. USB SOCKET PLASTIC FRAME OF THE FRONT PANEL SCREW 1. Remove plastic frame of the front panel from the unit. 2. Fix the unit with 4 pieces #8 pan head self tapping screw. 3. Put back plastic frame of the front panel to the unit. Page 1 Page 7 Common operation: After the device has been paired successfully and Wall mount Stereo screen displays BT LINK, Dial with mobile phone directly. 1. To turn the unit on/off . When the unit is power Off, it may be switched On by pressing POWER button. When the unit is switched On, press and hold POWER button for more than 1 second to switch the power off. 5. Accept/ Reject/ End A) During ringing, press TEL button to accept the call. B) During ringing, press HANG UP button to reject the call. C) During talking, press HANG UP button to end the call. 2. To select function mode Press the AUX,DVD,AM/FM,HDMI,USB,BT button on the front panel to select corresponding mode. Note: During ringing, CALL IN appears and then the phone number. 6. Talking volume level setting While in talking, use VOLUME +/- button to adjust volume level, but this volume level can not be saved. 3. To adjust the volume level Press the VOLUME + or VOLUME - button on the front panel to adjust volume level during playback. 7. Dialing or receiving calls while the unit is in sleep mode(when your phone is paired), When the Stereo is in sleep mode (Acc on and standby), to execute a dialing(with mobile phone) or receiving a call, the Stereo will temporarily wake up. 4. To mute or resume sound Press MUTE button to eliminate or resume sound immediately during playback. 8. To play an audio file from a external Bluetooth device(mobile phone) on the wall mount Stereo After the device has been paired successfully and Wall mount Stereo screen displays BT LINK. If your mobile device supports A2DP you will then be able to stream music from your Bluetooth device so it can be played by stereo speaker. You must select on your mobile Bluetooth device to play the audio through Bluetooth. If your mobile device supports AVRCP then you will be able to control the basic phone audio output functions by the Wall mount Stereo controls. Eg.Play Pause. 5. To set sound mode and menu Press and hold SEL button for more than 2 seconds to turn on BASS, then press SEL button shortly and repeatedly to select TRE(treble), LIR(balance),EQ OFF( FLAT/CLASSIC/ROCK /POP), LOUD OFF/LOUD ON, VOL LAST/VOL DEFA(AVOL) , BEEP ON/BEEP OFF, DX/LOCAL(in RADIO mode),STEREO/MONO(in RADIO mode),SUBW ON/SUBW OFF, AMERICA3/AUSTRIA/EUROPE(in RADIO mode) in the sequence and circulation. After selecting a desired item, use VOLUME+/- button to set. APP FUNCTION(Both support IOS system and Android system : 1,APP Installation. Another way to control the unit instead of using the front panel or remote control, you can use your phone. You will need to install the “Es Control” app onto your mobile device. The app will need to be downloaded from Google Play(Android phone) or App Store (Apple phone). Do a search for “Es Control” and proceed to download. Install per the app instructions. 2,Open the BT function of your smart phone and pair with the Stereo. 3,Under BT connection,tap the “Es Control” icon to enter the APP connection interface. then select the name“FURRION DV7100"(Android phone) or “DV7100-4.0"(Apple phone) to enter it. HDMI 4,Use the APP to control the Stereo freely. Ba kt so ur RADIO AV USB 1) BEEP ON/BEEP OFF BEEP ON mode: The beep is generated when any key is pressed. BEEP OFF mode: The beep sound is disabled. 2) VOL LAST/VOL DEFA VOL LAST: The volume level when switching off will be restored with power On. VOL DEFA: The volume level of the main unit after power on is a constant value. when selecting VOL DEFA item, press SEL button to display AVOL , then you can pre-set the constant volume level after power on with VOL control. 3) DX/LOCAL Radio station search mode is divided by this DX/LOCAL switch, which can be used to control an attenuator in the tuner during search. The detecting level of seek, scan, auto-memory will be reduced as much as the attenuated level of the tuner. In radio mode, press the LOC button to change local reception or distance reception. (Note: This button is only for FM reception. In AM mode, LOC is invalid.) 6. DISPLAY AND ADJUST THE TIME Press and hold the 6 button for more than 2 seconds until the real time flashes on the display. Then you can adjust HOUR by VOLUME +/- button, and adjust MINUTE by / button. 7. To adjust the backlight Press and hold the 5/BACKLIGHT button repeatedly to adjust the backlight. APP ICON CONNECT BT SOURCE AUX Preferences Page 6 8. ALARM FUNCTION 1)set the ALARM mode on or off Press and hold the 6 button repeatedly to enter ALARM ON/OFF mode. ( use VOLUME +/- button to select ALARM ON or ALARM OFF) Page 2 2)set the ALARM time Press and hold the 6 button repeatedly to ALARM time setting mode(the LCD will display the time “AM 00'00 “ but not flash), then use the / button to set the MINUTE and VOLUME +/- button to set the HOUR. 9. To reset unit 1,Press RESET with a cuspidal object to make the unit be reset to factory default and re-instate the correct functions. 2, In AUX mode, Press and hold 2/STOP button until the LCD displays “RESET III, then press and hold 3/RPT button to reset to the factory default. Radio Operation: 1. To select radio band Press AM/FM button briefly and repeatedly to select a desired radio band in sequence and circulation as follows: -->FM1-->FM2-->FM3-->AM1-->AM2--> 2. To search for radio station manually or automatically Press >>| or |<< button briefly to manual tune up/down for your desired radio stations step by step. Press and hold >>| or |<< button for 2 seconds to automatically tune up/down for a radio station of strong signal. 3. To store current station or turn on a preset one 1) If you want to store currently station, press and hold the AM/FM button until the frequency flashes, then press briefly one of the 6 number buttons to store the current station in the preset memory bank of the number button for the current band. In this way the unit can store 30 preset stations. 2) Press one of the 6 number buttons briefly to turn on the preset station stored in the preset memory bank of the number button for the current band. 4. To auto search and store for the strongest stations When pressing and holding 2/STOP button on the front panel for more than 2seconds, the radio searches from the current frequency and checks the signal strength level until the 6 strongest stations are found. And then the 6 strongest stations are preset to the corresponding preset memory numbered bank. The auto-storage operation is implemented in the each selected band. When the auto-storage operation is finished, the radio executes Preset scan. 5. To set the frequency Press and hold SEL button for more than 2 seconds to turn on BASS, then press SEL button shortly and repeatedly until displays one of the area AMERICA3,AUSTRIA or EUROPE, then use the VOLUME+/- button to selection and briefly press the SEL button for your confirmation. USB Operation: 1. To insert or pull out USB stick When needing to playback USB music, insert USB stick into the USB socket, then the playing mode will be changed into USB mode and display “USB” on the LCD. 2. Press the or button briefly to play previous or next track. 3. To play fast forward or backward Press and hold or button to play backward or fast forward. 4. To play previous or next 10th track Press 5 or 6 button to play previous or next 10th track. 5. How to use 1/PLAY/PAUSE button During playback, press 1/PLAY/PAUSE button to pause playback. When in pause mode, press 1/PLAY/PAUSE button to play again. Press and hold 1/PLAY/PAUSE button to select the first track for playback. 6. To repeat track(s) During playback, press 3/RPT button briefly to play the current track repeatedly, and the LCD will display RPT ONE. Press RPT button twice to play the tracks in the Album repeatedly, and the LCD will display RPT DIR. Press RPT button thrice to RPT ALL tracks, and the LCD will display RPT ALL. Press RPT button four times to cancel RPT function , and the LCD will display RPT OFF. 7. To play tracks in random During playback, press RDM button briefly to play all tracks in random. Press it again to cancel RDM function. 8. Tracks search Press USB button, it will activate TRACK SEARCH mode . The LCD will display TRK 0/00/000(deside on the total number of tracks in the SD card or USB stick) and flash the 0 on the biggest digit position. Then use the VOLUME +/- button to select a number on the flashing digit position from 0 ~ 9. Then press USB button to confirm the number and flash the 0 on next smaller digit position. With the same means, select the number on the flashing digit position with VOLUME +/- button. After finishing selecting the numbers on all digits position, press 1/PLAY/PAUSE button to play the track of the selected serial number. BlueTooth Handsfree System: 1. Pairing Turn on Bluetooth mode of mobile phone, then select the function of Finding Bluetooth Device and enter it. After finishing the finding, it will show the name of Bluetooth Device "FURRION DV7100" , select it and enter it, (for some phones it maybe need a password, In case of this situation please Input the password 0000),then the LCD of the car audio system will display “BT LINK”. 2. Use mobile phone to do connection or disconnection 1) In connection status, find the paired and connected Bluetooth Device, then press the disconnection button to do disconnection. 2) In disconnection status, find the paired and disconnected Bluetooth Device, then press the connection button to do connection 3. In connection status: Mobile phone transfers to car audio player whenever a dialing takes place; Mobile phone transfers to car audio player whenever receiving a call. 4. Dialing when in connection status Page 3 Page 4 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : scb Title : 未命名 -1 Create Date : 2016:04:13 10:04:13+08:00 Creator Tool : CorelDRAW X6 Modify Date : 2016:06:08 10:07:51+08:00 Metadata Date : 2016:06:08 10:07:51+08:00 Producer : Corel PDF Engine Version 16.1.0.843 Document ID : uuid:fb5dd0f3-87a4-48ac-b866-734fe4df4d41 Instance ID : uuid:5738a579-99c8-4fb8-87e7-e325fb15e4e4 Page Count : 5 Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Author : scbEXIF Metadata provided by EXIF.tools