Furuno USA 9ZW19P1079 Wireless LAN module User Manual WLAN USB 01x
Furuno USA Inc Wireless LAN module WLAN USB 01x
User manual
User Manual
802.11bgn WLAN MODULE
MODEL WLAN-USB-01
The purpose of this manual is to explain correct way how to integrate module
WLAN-USB-01 to the end product. It includes procedures that shall assist you to
avoid unforeseen problems. This manual presents information that shows how
module and OEM product, where module integrated, complies with regulations
in certain regions. Any modifications, not expressly approved by the
manufacturer could void the authority to operate in these regions.
The 802.11bgn WLAN MODULE, model WLAN-USB-01 is only be professionally
installed by OEM or OEM integrator.
For detail information concerning type approval of this module (e.g. where this
module is already pre-approved) please contact the authorized local distributor
or the manufacturer.
The system may only be implemented in the configuration that was authorized.
Note that any changes or modifications to this equipment not expressly
approved by the manufacturer could void the user’s authority to operate this
equipment.
Regulatory Information
Operational Information
Wireless Interoperability
The end product integrating this module is designed to be interoperable with any
wireless LAN product that is based on direct sequence spread spectrum (DSSS)
and orthogonal frequency division multiplexing (OFDM) radio technology and to
comply with the following standards.
･IEEE Std 802.11b Standard on 2.4GHz Wireless LAN
･IEEE Std 802.11g Standard on 2.4GHz Wireless LAN
･IEEE Std 802.11n Standard on 2.4GHz Wireless LAN
Safety
The end product integrating this module, like other radio devices, emits radio
frequency electromagnetic energy. The level of energy emitted by this device,
however, is less than the electromagnetic energy emitted by other wireless
devices such as mobile phones. The end product integrating this module
operates within the guidelines found in radio frequency safety standards and
recommendations. These standards and recommendations reflect the
consensus of the scientific community and result from deliberations of panels
and committees of scientists who continually review and interpret the extensive
research literature. In some situations or environments, the use of the end
product integrating this module may be restricted by the proprietor of the building
or responsible representatives of the applicable organization. Examples of such
situations include the following:
･Using the end product integrating this module onboard airplanes, or
･Using the end product integrating this module in any other environment
where the risk of interference with other devices or services is perceived
or identified as being harmful.
If uncertain of the policy that applies to the use of wireless devices in a specific
organization or environment (an airplane, for example), ask for authorization to
use the end product integrated into this module before turning it on.
USA-Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by tuning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Labeling
WLAN MODULE “WLAN-USB-01” labeled as below.
FCC ID: ADB9ZW19P1079
The label with FCC ID is to be placed on the module. If FCC ID is not visible
when the module is installed into the system, “Contains FCC ID:
ADB9ZW19P1079” shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65. This equipment should be installed and
operated keeping the radiator at least 20cm or more away from person’s body.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of this device.
L ‘ utilization de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fomctionnement du dispositif.
Labelling
WLAN MODULE “WLAN-USB-01” labeled as below.
IC: 1281B-19P1079
The label with IC No. is to be placed on the module. If IC No. is not visible when
the module is installed into the system, “Contains IC: 1281B-19P1079” shall be
placed on the outside of final host system.
The term “IC” before the equipment certification number only signifies that the
Industry Canada technical specifications were met.
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (EIRP)
is not more than that required for successful communication.
Caution: Exposure to Radio Frequency Radiation.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person’s body.
Cet équipement est conforme aux limites d’exposition aux rayonnements
énoncées pour un environnement non contrôlé et respecte les règles
d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet
équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus
entre le dispositif rayonnant et le corps.