Furuno USA 9ZWFM8800S VHF Marine Radiotelephone User Manual OPERTORS MANUAL

Furuno USA Inc VHF Marine Radiotelephone OPERTORS MANUAL

UserManual.wiki >

Furuno USA >

9ZWFM8800S User Manual HTML Version

OPERTORS MANUAL

VHF RADIOTELEPHONE

FM-8800D/8800S

Your Local Agent/DealerYour Local Agent/Dealer

9-52 Ashihara-cho,9-52 Ashihara-cho,

Nishinomi

a 662-8580, JAPANNishinomi

a 662-8580, JAPAN

Tele

hone :Tele

hone : 0798-65-21110798-65-2111

FaxFax 0798-65-42000798-65-4200

IRST EDITION :

IRST EDITION : SEPSEP.. 20042004

Printed in JapanPrinted in Japan

ll ri

hts reserved.

ll ri

hts reserved.

A1A1 :: SEPSEP.. 22, 200422, 2004

Pub. No.Pub. No. OME-56420OME-56420

00014993000

(( TATATATA )) FM-8800D/SFM-8800D/S * 0 0 0 1 4 9 9 3 0 0 0 ** 0 0 0 1 4 9 9 3 0 0 0 *

OME

56420

OME

56420

OME

56420

OME

56420

* O M E 5 6 4 2 0 A 1 0 ** O M E 5 6 4 2 0 A 1 0 *

CANCELING DISTRESS ALERT

If less than three seconds has elapsed since the [DISTRESS] key was pressed,

the distress alert may be canceled by pressing the [CANCEL] key. Otherwise, do

the following:

1. Switch off equipment immediately.

2. Switch equipment on and set to Channel 16.

3. Transmit message to “All Stations” giving your vessel's name, callsign and

DSC number to cancel the distress alert.

Example message:

All Stations, All Stations, All Stations

This is VESSEL'S NAME, CALLSIGN,

DSC NUMBER, POSITION.

Cancel my distress alert of

DATE, TIME, UTC.

=Master, VESSEL'S NAME, CALLSIGN.

DSC NUMBER, DATE, TIME UTC.

SAFETY INSTRUCTIONS

Do not disassemble or modify the

equipment.

Fire, electrical shock or serious injury

can result.

Turn off the power immediately if water

Do not open the equipment.

leaks into the equipment or the equip-

ment is emitting smoke or fire.

Continued use of the equipment can cause

fire or electrical shock.

Do not place liquid-filled containers on

the top of the equipment.

Fire or electrical shock can result if a

liquid spills into the equipment.

Any repair work must be done by a

licensed radio technician.

Improper repair work can cause electrical

shock or fire.

Do not operate the equipment with wet

hands.

Electrical shock can result.

Keep heater away from equipment.

Heat can alter equipment shape and melt

the power cord, which can cause fire or

electrical shock.

Hazardous voltage which can

cause electrical shock, burn

or serious injury exists inside

the equipment. Only qualified

personnel should work inside

the equipment.

WARNINGWARNING

CAUTION

Do not touch any part of the antenna

when the equipment is transmitting.

Electrical shock can result.

Use the proper fuse.

Use of a wrong fuse can result in fire or

cause permanent damage to the equipment.

WARNING

To avoid electrical shock, do not

remove cover. No user-serviceable

parts inside.

Terminal, Communication

Unit

Name: Warning Label (1)

Type: 86-003-1011

Code No.: 100-236-231

Do not approach the antenna

closer than 33 cm when it

is transmitting.

The antenna emits radio waves

which can be harmful to the

human body.

WARNINGWARNING

FM-8800S

RF power density

on antenna aperture distance

100 W/m20.11 m

10 W/m20.33 m

FM-8800D 100 W/m20.10 m

10 W/m20.33 m

iii

TABLE OF CONTENTS

FOREWORD ......................................................................................................... v

SYSTEM CONFIGURATION............................................................................... vii

SPECIFICATIONS........................................................................................... SP-1

1. OPERATIONAL OVERVIEW

1.1 Controls Keys and LCD Indication .............................................................................1-1

1.2 VHF Basic Operation .................................................................................................1-7

1.3 DSC Operational Overview......................................................................................1-10

1.4 Priority .....................................................................................................................1-12

2. DSC DISTRESS COMMUNICATION

2.1 Distress Alert Transmission from the DISTRESS Key................................................2-1

2.2 Distress Alert Transmission with Nature of Distress ...................................................2-3

2.3 Distress Alert Transmission From CALL Key..............................................................2-4

2.4 Canceling a False Distress Alert ................................................................................2-6

2.5 Receiving Distress Alert from Other Vessel, Transmitting DIST ACK Signal...............2-6

2.6 Sending Distress Relay on Behalf of a Ship in Distress ........................................... 2-11

2.7 Receiving Distress Relay.........................................................................................2-15

3. DSC OPERATION FOR NON-DISTRESS CASES

3.1 Coast or Ship Call......................................................................................................3-1

3.2 Group Call ...............................................................................................................3-10

3.3 PSTN Call................................................................................................................3-13

3.4 All Ships Call............................................................................................................3-16

3.5 Geographical Area Call............................................................................................3-19

3.6 Position Call.............................................................................................................3-22

3.7 Polling Call...............................................................................................................3-25

3.8 Neutral Craft Call .....................................................................................................3-29

3.9 Medical Transport Call .............................................................................................3-30

3.10 Log File....................................................................................................................3-32

4. BASIC SETUP

4.1 Alarm Setup...............................................................................................................4-1

4.2 Auto ACK Setup.........................................................................................................4-3

4.3 Erasing Logs..............................................................................................................4-5

4.4 Memory Channel Setup .............................................................................................4-6

4.5 Message File Entry....................................................................................................4-7

4.6 Position Setup.......................................................................................................... 4-11

4.7 Print Out Setup ........................................................................................................4-12

4.8 Volume Setup ..........................................................................................................4-13

TABLE OF CONTENTS

5. SYSTEM SETUP

5.1 Displaying Self ID...................................................................................................... 5-1

5.2 Displaying Group ID LIST.......................................................................................... 5-1

5.3 Naming Intercom....................................................................................................... 5-2

5.4 Displaying Program Version ...................................................................................... 5-3

6. MAINTENANCE & TROUBLESHOOTING

6.1 Maintenance.............................................................................................................. 6-1

6.2 Troubleshooting......................................................................................................... 6-1

6.3 Daily Test................................................................................................................... 6-2

6.4 Error Message........................................................................................................... 6-3

6.5 Parts Location ........................................................................................................... 6-3

APPENDIX ......................................................................................................AP-1

Menu Tree.......................................................................................................................AP-1

Marine VHF Channel Lists...............................................................................................AP-3

Digital Interface (IEC 61162-1 Edition 2)........................................................................AP-14

FOREWORD

A Word to FM-8800D/FM-8800S Owners

Congratulations on your choice of the FURUNO FM-8800D/FM-8800S VHF

Radiotelephone. We are confident you will see why the FURUNO name has

become synonymous with quality and reliability.

For over 50 years FURUNO Electric Company has enjoyed an enviable

reputation for quality marine electronics equipment. This dedication to

excellence is furthered by our extensive global network of agents and dealers.

This equipment is designed and constructed to meet the rigorous demands of

the marine environment. However, no machine can perform its intended function

unless operated and maintained properly. Please carefully read and follow the

recommended procedures for operation and maintenance.

We would appreciate hearing from you, the end-user, about whether we are

achieving our purposes.

Thank you for considering and purchasing FURUNO equipment.

FOREWORD

Features

The FURUNO FM-8800D/FM-8800S is a cost-effective all-in-one marine VHF

radio system consisting of a 25 W VHF radiotelephone, a DSC modem, and a

CH 70 watch receiver. It complies with GMDSS carriage requirements for safety

and general communications.

The FM-8800D offers full-duplex voice communications and the FM-8800S

offers simplex voice communication on ITU channels in the marine mobile VHF

band. The features include Dual Watch which allows a continuous watch on

CH16 and another selected frequency.

Full Class-A DSC functions are provided for distress alert transmission and

reception, as well as the general call formats (Individual telephone, All Ships,

Group and Area Call). Distress alert can be readily transmitted but an

arrangement is provided to prevent accidental activation. The FM-8800D/

FM-8800S maintains a continuous watch on CH70 even while another VHF

channel is in use. Aural and visual alarms are given to incoming DSC messages.

The main features of the FM-8800D/FM-8800S are

• Compact cabinet allows for flexible and space-saving installation on a

navigation console or at the conning position

• Conforms to the following standards and regulations:

IMO A.694(17)

IMO A.803(19)

IMO A.524(13)

IMO MSC 68(68), MSC/Circ.862

IEC61097-3/7/8

IEC60945 (4th edition)

IEC61162-1 (July 2000)

ETS 300 338, 300 698, 301 925

ITU-R M.493-10, M.541-8, M.689-2

• Full-duplex communications: FM-8800D

• Precision PLL frequency synthesizer for high frequency stability as required for

DSC operation

• Dual Watch and Multiple Watch

• Continuous DSC watch on CH70

• Prevention of accidental distress alert

• File editing for emergency readiness

• Automatic entry of own ship position with manual override

Program number

FM-8800D/FM-8800S: 0550215-02

vii

SYSTEM CONFIGURATION

The FM-8800D/FM-8800S is a highly advanced 25 W VHF transceiver with DSC

terminal. It is designed to satisfy the stringent requirements of marine

communications, and complies with GMDSS carriage requirements for safety

and general communications.

TRANSCEIVER UNIT

FM-8800D

FM-8800S

Handset

HS-2003

VHF

Antenna CH 70 RX

Antenna

AC/DC

Power Supply

Unit

PR-240-CE

100/220 VAC

50/60 Hz, 1φ

Category of units

Antenna

All other units

Exposed to weather

Protected from weather

Category

Radio Battery

24 VDC

Junction

Box

IF-8810 Remote box

RB-

8800/8810

HS-8800

Printer

PP-510

External

Speaker

SEM-21Q

DMC I/F

IF-8820

Wing handset

T/R AF output for VDR

MAX

2 sets

MAX

4 sets

IEC61162-1 input

DSC information output

Unit

External alarm

FM-8800D/FM-8800S system configuration

viii

This page is intentionally left blank.

SP-1

SPECIFICATIONS OF MARINE VHF RADIOTELEPHONE

FM-8800D/FM-8800S

1. GENERAL

(1) Number of Channels INTL: 57

USA: 55 (57)*

Weather: 10

Canada: 55 (57)*

INLND-WA: 55 (57)*

Private: 20 *: CH75&76 can be included

MEMORY CH: 50 for some countries.

(2) Frequency Stability Within ±1.5 kHz

(3) Communication System FM-8800S: Simplex/Semi-duplex

FM-8800D: Simplex/Full-duplex

(4) Class of Emission 16K0G3E (Voice)

16K0G2B (DSC)

(5) Antenna Impedance 50 ohms

2. TRANSMITTER

(1) Frequency Range

(2) Output Power 25 W max., 1 W at power reduction

(3) Frequency Deviation <5 kHz

3. RECEIVER

(1) Frequency Range

(2) Receiving System Double Superheterodyne

(3) Intermediate Frequency 1st: 51.2375 MHz, 2nd: 37.5 kHz

(4) Sensitivity +6 dBµV (20 dB SINAD)

(5) Adjacent Channel Selectivity 70 dB or more

(6) Spurious Response 70 dB or more

(7) AF Output Built-in Speaker: 3 W (4 ohms)

Handset earphone: 2mW (150 ohms)

4. DSC

(1) Protocol ITU-R Rec. 541-8, 493-10 (class A)

(2) Baud Rate 1200 baud ±30 ppm max.

(3) Modulation AFSK

(4) Frequency Shift 1700 ±400 Hz

Mark: 1300 Hz, Space: 2100 Hz

Simplex 155.000 to 161.475 MHz FM-8800S

Semi-duplex 155.000 to 161.475 MHz

Simplex 155.000 to 158.000 MHz FM-8800D

Full-duplex 155.000 to 158.000 MHz

Simplex 155.000 to 159.600 MHz FM-8800S

Semi-duplex 161.475 to 166.075 MHz

Simplex 155.000 to 158.000 MHz FM-8800D

Full-duplex 160.625 to 162.600 MHz

SP-2

5. CH70 WATCH RECEIVER

(1) Receiving Frequency 156.525 MHz

(2) Sensitivity Symbol error rate: Less than 1% (at 0 dBµV)

(3) Conducted Spurious Emission Less than 2 nW

6. POWER REQUIREMENTS

(1) Power Supply 24 VDC (-10%/+30%)

(2) Power Consumption

7. DIGITAL INTERFACE IEC 61162-1 (NMEA0183 Ver.3)

Sentence IN: GGA>RMC>GNS>GLL>ZDA

OUT: TLL

Talker: GP>LC>DE>II>IN>EC

8. AMBIENT CONDITIONS

(1) Temperature -15°C to 55°C (IEC60945)

(2) Relative Humidity 93% (at 40°C)

(3) Waterproofing (IEC 60529)

Transceiver Unit Chassis: IPX0

Panel: IPX4

Handset/Hanger HS-2003: IPX-4

Remote Box/Handset RB-8800: IPX-0

HS-8800:IPX-2

Junction Box IF-8810: IPX-0

DMC Interface IF-8820: IPX-0

9. COATING COLOR

(1) Transceiver Unit Chassis: Munsell 2.5GY5/1.5

Panel: Munsell N3.0

Waiting 0.5 A

Receive 1.6 A at 4 W audio output

FM-8800S

Transmit 1.6 A at 1 W output,

4.7 A at 25 W output

Waiting 0.5 A

Receive 1.6 A at 4 W audio output

Transmit 2 A at 1 W output,

6 A at 25 W output

FM-8800D

DUP Transmit 3.6 A at 1 W output,

7.6 A at 25 W output

1-1

1. OPERATIONAL OVERVIEW

The FM-8800D/FM-8800S system consists of a transceiver block and two

antennas. The transceiver block contains a VHF transmitter, receiver, and

channel 70 watch receiver module. FM-8800D additionally provides a duplexer

block. All operations are controlled on its front panel.

1.1 Controls Keys and LCD Indication

1.1.1 Front panel

The alert is transmitted with steady lighting.

Keep pressed for 4 s in case of DISTRESS.

MSG

CALL

SHIFT

HI/L0

USA

PQRS

INTL

SCAN

TUV

ENT

9DW

WXYZ

DISTRESS

GHI

IntCom

JKL

ACK

1 2

ABC

FILE

MNO

CH16

DEF

TEST

CANCEL

LOG

ALARM

CHANNEL

PUSH TO ENTER

SQUELCH

HANDSET

VOLUME/POWER

AUTOOFF

Volume with

Power ON/OFF Squelch control

Transmits the distress alert.

Press this button three seconds continuously.

LCD

Transmits various

messages.

Channel selector

Handset port

Loudspeaker

Transceiver unit

DISTRESS

VOLUME

ALARM

LCD

Keyboard

Loudspeaker

Distress button

Volume control

HS-8800

Handset

HG-8800

Handset hanger

Remote station (option)

1. OPERATIONAL OVERVIEW

1-2

1.1.2 Controls

The functions of keys of the transceiver unit and the remote station are almost

the same. The table below shows the controls and keys for the transceiver unit.

Control Function

CHANNEL

(PUSH TO

ENTER)

• Selects a channel.

• Moves the cursor in menu opened.

• Registers selected item when pressed.

SQUELCH

• Mutes the receiver when no signal is present on

the channel selected.

• AUTO position automatically reduces white noise.

VOLUME/POWER • Turns the power on/off and adjusts the volume of the

loudspeaker.

Key Function

DISTRESS

• Transmits the distress alert after pressing three seconds.

When the key is pressed, the LED in the key blinks and the

buzzer sounds. Pressing the key three seconds

continuously the distress alert is transmitted and the LED

lights continuously and buzzer also sounds continuously.

These conditions are continued until the distress

acknowledge is received or you cancel the distress alert.

ALARM

(INDICATOR)

• Blinks in red when a distress alert or urgent call is received.

Also, the acoustic alarm sounds. To stop the blinking and

silence the buzzer, press the CANCEL key.

• Blinks in green when a safety call or routine call is received.

The acoustic alarm sounds and stops automatically five

seconds later.

CANCEL

• Stops audible and visual alarms.

• Erases an error message.

• Cancels numeric entry.

• Returns to previous menu.

• Cancels transmission or printing.

CALL

MSG

• Transmits various DSC messages. To transmit a distress

message, press this key more than three seconds.

1. OPERATIONAL OVERVIEW

1-3

• Enters 1, ., ,, √, ”, :, ;, -, +, *, #, , (, ), !, $, &, / character at

entry mode.

• Turns the loudspeaker on or off. Pressing the SHIFT and

then this key turns loudspeaker on or off.

In the off state, the loudspeaker icon disappears. However,

the key click actives and the alarm sounds when a distress

or urgent call is activated.

ABC

• Enters alphanumeric data (2, A, B, C).

• Adjusts panel illumination when proceeded by the SHIFT

key.

TEST

DEF

• Enters alphanumeric data (3, D, E, F).

• Performs the daily test when proceeded by the SHIFT key.

IntCom

GHI

• Enters alphanumeric data (4, G, H, I).

• Turns the interphone on or off when proceeded by the

SHIFT key and followed by ENT key. Available when a

remote handset is connected.

ACK

JKL

• Enters alphanumeric data (5, J, K, L).

• Turns auto acknowledge of routine calls on or off.

MNO

• Enters alphanumeric data (6, M, N, O).

• Prints communication files, current display and daily test

result.

INT/USA

PQRS

• Enters alphanumeric data (7, P, Q, R, S).

• Changes the channel mode among INTL, USA**, WX**,

CANADA**, INLND-WA** and (MEMO)*.

*: If registered.

**: Required system setting by qualified serviceman only.

SCAN

TUV

• Enters alphanumeric data (8, T, U, V).

• Turns the scan function on or off.

WXYZ

• Enters alphanumeric data (9, W, X, Y, Z).

• Turns the dual watch function on or off.

1. OPERATIONAL OVERVIEW

1-4

HI/LO

• Enters “0”.

• Changes the output power high (25 W) or low (1 W).

However, the following channels are always 1 W.

INTL mode: CH15, CH17, CH75, CH76

USA mode: CH13, CH17, CH67

▲

SHIFT

• Press to activate secondary function.

• Moves the screen to previous item.

▼

LOG

• Displays transmitting/receiving messages.

• Moves the screen to next item.

CH16 • Selects CH16 by one-touch action.

FILE • Opens the Message file list.

MENU • Opens the SETUP menu.

ENT

• Registers data input.

（Same as pressing the CH selector.）

Additional keys of the handset HS-8800

Key Function

(up arrow key)

• With the SHIFT key pressed, this key increases volumes of

internal loudspeaker of remote station.

• Increments channel number or setting value.

• Adjusts squelch level with or key.

(down arrow key)

• With the SHIFT key pressed, this key decreases volumes

for internal loudspeaker of remote station.

• Decrements channel number or setting value.

SQ auto

• With the SHIFT key pressed, this key adjusts auto squelch

level.

1. OPERATIONAL OVERVIEW

1-5

1.1.3 Indications on the LCD

Below are all the indications which appear on the standby display on the

transceiver unit.

INTL

910

11 12

DUP

116

SCAN

SHIFT

AUTO ACK WATCH CH70 *

LAT: 34 45' N

°10:45 UTC

LON: 135 45' E

°AUTO

Standby display on the transceiver unit

Reference no. meaning

① Displays the channel mode.

(INTL / USA / WX / CANADA / INLND-WA / (MEMO))

② SHIFT is displayed if the shift function is active. Or memory number (for

example MEMO 01) is displayed at the MEMO mode.

③ Displays the scan mode: SCAN, DUAL or no display. During the scan

mode, channel indications are changed alternatively. No display means

that the unit receives continuously on the same channel.

④ Lights when the loudspeaker is off. Goes off when the loudspeaker is on.

⑤ Displays the transmission output.

(Hi=25W / Lo=1W)

⑥

Displays reception signal strength by 4 steps.

1. No signal. Only antenna mark is displayed.

2. Less than 37.6 dB (-100.6 dBm) SINAD：antenna mark and short bar

3. 40.0 dB (-96.9 dBm) SINAD and more：antenna mark and two bars

4. 41.9 dB (-92.9 dBm) SINAD and more：antenna mark and three bars

⑦ RX is displayed during reception and TX is displayed when

the RF signal detected at transmission state.

⑧ Displays the current channel.

（PRIV channel: max three digits）

⑨ Is displayed when the DSC routine call is received.

AUTO ACK: Automatic acknowledge

MANUAL ACK: Manual acknowledge

⑩ WATCH CH70 or WATCH VHF is selected at menu.

If the CH70 board is defective, WATCH CH70 NG appears.

⑪ Displays the longitude and latitude of own ship.

⑫ Displays UTC time.

⑬ Displays AUTO for automatic data input (L/L, time data) from a navigation

device or MANUAL for manual data input.

⑭ Displays when un-read message(s) exist.

*: If no MMSI is registered, the message “DSC NOT USABLE” appears.

1. OPERATIONAL OVERVIEW

1-6

Below are the indications which appear on the standby display on the remote

handset.

INTL

RX SCAN

DUP

SHIFT

MANUAL ACK** 3*

GPS ERROR

LAT: 12 34' N

LON: 123 45' E

12:34 UTC

AUTO

WATCH CH70**

If you press

at the left-hand screen, right-hand screen appears for 30

seconds.

If you press

at the right-hand screen, the left-hand screen appears

immediately.

The indications are the same as those on of the transceiver unit.

The *- marked number is the terminal number of the remote station.

**: If no MMSI is registered, the message “DSC NOT USABLE” appears instead

of MANUAL ACK and WATCH CH70.

Note: The screen of the remote handset is smaller than the one of the

transceiver unit. In this manual, display examples are from the transceiver

unit. In the remote handset, scrolling with up or down arrow key displays

same information as the screen of the transceiver unit.

1.1.4 Audio alarms

When you receive a distress alert or routine call, etc., the audible and visual

alarms are released. For the distress or urgency call, the audio alarm sounds

until the CANCEL key is pressed. For all other calls, the audible alarm sounds

for one second and the automatically goes off. The tone of the alarm changes

with the call received. By becoming accustomed to the tone, you can know

which type of call you have received.

1. OPERATIONAL OVERVIEW

1-7

Alarm Frequency (interval)

Safety call received 1300 Hz and 0 Hz (250 ms)

Routine, Ship’s Business call received 880 Hz and 440 Hz (500 ms)

While DISTRESS key is pressed for

three seconds

2200 Hz and 0 Hz (125 ms)

Distress alert sent 2200 Hz, continuous

Own ship position not updated 2200 Hz (50 ms), three beeps every two

seconds

Distress alert, urgency message

received

1300 Hz and 2200 Hz (250 ms)

Message received from terrestrial

telephone line

750 Hz and 650 Hz (50 ms) 10 times

Repeat OFF one second

1.2 VHF Basic Operation

1.2.1 Turning the power on/off

To turn the power on, turn the VOLUME control clockwise until you hear a click.

To turn the power off, turn the control fully counterclockwise until you hear the

click.

1.2.2 Selecting channel modes, channels

Selecting channel modes

To change the channel mode, press the SHIFT key immediately followed by the

7 INT/USA key several times until desired mode is displayed. The following

modes are available.

INTL : International mode

USA/WX : USA mode/ Weather channel mode

CANADA : CANADA mode

INLND-WA : Rhine river mode (USED ON INLAND Waterways)

MEMO : Memory channel mode if registered

Note: Private channels are available only where permitted by the authorities.

The USA/WX, CANADA, INLND-WA can also be set by a qualified

serviceman.

Selecting channels

Rotate the CH selector clockwise (counterclockwise) to display desired channel.

1. OPERATIONAL OVERVIEW

1-8

1.2.3 Adjusting volume of loudspeaker

The VOLUME control adjusts the volume of the loudspeaker.

1.2.4 Adjusting squelch

The SQUELCH control adjusts the squelch threshold level. Adjust it so that white

noise heard in the loudspeaker just fades out. Perform this operation when no

traffic is being received. AUTO squelch automatically reduces white noise.

Usually select the AUTO position. Avoid turning the squelch too far clockwise —

you may miss a long distance communication.

Note: To obtain correct scan watch/dual watch response, adjust the SQUELCH

control precisely.

1.2.5 Transmitting

Press the PTT (Push-to-talk) switch on the handset or microphone to talk, and

release it to listen for the response. The VHF section keyboard accepts no key

input when the PTT switch is operated.

Remarks on transmitting

• Before transmitting, think about the subjects which have to be communicated

and, if necessary, prepare written notes to avoid unnecessary interruptions

and ensure that no valuable time is wasted on a busy channel.

• Listen before commencing to transmit to make certain that the channel is not

already in use.

1.2.6 Selecting output power

After pressing the SHIFT key, each press of the 0 HI/LO key selects high or low

output power. Also Hi or Lo appears on the screen depending on your selection.

The transmitter power is automatically set for low on the following channels:

International: CH15, CH17, CH75, CH76

USA: CH13, CH17, CH67; to operate USA channel 13 or 67 in high

power, keep HI/LOW pressed while talking into the handset.

1.2.7 Turning the loudspeaker on/off

To turn the loudspeaker on/off, press the SHIFT key, then the 1 key. The

loudspeaker off mark appears when the speaker is off. The loudspeaker is

automatically turned off when the telephone handset is used.

1. OPERATIONAL OVERVIEW

1-9

1.2.8 Quick selection of CH16

Press the CH16 key to select CH16, the International Calling and Safety

Channel. The use is limited to distress, safety and calling. The transmission on

CH16 (156.800 MHz) should be limited to within 1 minute except for distress

calling.

Avoid calling on CH16 for purposes other than distress, urgency and very brief

safety communications when another calling channel is available.

1.2.9 Dual watch

The dual watch function permits watch on CH16 and another selected channel.

CH16 and another channel are watched at intervals of 0.15 seconds and one

second, respectively.

To start dual watch, first select the other frequency to watch and then press the

SHIFT key and 9 DW key in that order. When the receiver finds a signal on

CH16, it locks on it and restarts dual watching after the signal on CH16 has gone.

If another channel has traffic, it still continues dual watch. The speech is heard

intermittently. If you are annoyed with the intermittence, turn off the dual watch

by pressing the PTT switch on the handset or pressing the SHIFT and 9 DW key

again.

1.2.10 Scanning

The receiver scans all channels at intervals of 0.15 seconds in the selected

channel mode in ascending channel order, watching CH16 between channels as

below:

1 16 2 16 3 16 4...

16 88 16 87 16 86 16...

To start scanning, press the SHIFT and 8 SCAN in that order. When the receiver

finds a signal, scanning is stopped on that channel and starts dual watch on it

and CH16.

1.2.11 Remarks on voice communications

Automatic acknowledge (DSC operation) is automatically changed to manual

acknowledge when voice communications begin. (The “auto” indication, however,

remains on the screen.) This is done to prevent a break in communications.

Automatic acknowledge is automatically restored once voice communications

are terminated.

1. OPERATIONAL OVERVIEW

1-10

1.3 DSC Operational Overview

Digital Selective Calling (DSC) is the global calling system adopted by the ITU-R

and IMO for selective calling of coast station and ship radio stations. The DSC

system is used for both safety and routine calling. The GMDSS requires the use

of DSC for distress alerting and safety calls.

1.3.1 LED warnings

The LED below the DISTRESS key lights continuously when the distress signal

is transmitted.

The ALARM LED blinks in red (and alarm sounds) when a distress or urgent

message is received. The LED can be extinguished and alarm silenced by

pressing the CANCEL key.

The ALARM LED blinks in green (and alarm sounds) when a message other

than distress or urgent is received. Alarm is automatically silenced five seconds

after message is received.

1.3.2 DSC operational overview

Standby display

When the FM-8800D/S is turned on, the following display appears. This display

is known as the “standby display.” This is where you will begin most operations.

INTL

116

SCAN

SHIFT

AUTO ACK WATCH CH70

LAT: 34 45' N

10:17 UTC

LON: 135 45' E

AUTO

INTL

RX SCAN

SHIFT

MANUAL ACK 1

SCAN

116

VOL 5 SQ 2

Standby display (Transceiver unit) Standby display (Remote handset)

(Press the down arrow key of the

remote handset to view rest of

screen.)

If you get lost in operation you can return to the standby display by pressing the

CANCEL key several times.

Note: In this manual, screen examples show the transceiver’s screens. To get

the same information on the handset screen, press down or up arrow key.

1. OPERATIONAL OVERVIEW

1-11

Preparing and transmitting DSC messages

There are two methods by which you can prepare and transmit DSC messages,

and they are shown below.

● Preparing message for immediate transmission

1. Press the CALL key at the standby display.

2. Select the call type.

3. Select other party if necessary.

4. Select the communications category.

5. Select the communications channel.

6. Press the CALL key.

● Transmitting a message stored in the memory

100 messages can be saved to the memory. You may open a memory-stored

message and transmit it.

Distress alert transmission and output power

When the distress alert is transmitted (by pressing the DISTRESS key), the

output power of the FM-8800D/S is automatically set to maximum (25 W).

When keyboard input is prohibited

DSC-related controls cannot be operated while a DSC message is being

transmitted. (These controls are inoperative about 3 seconds during a DSC

distress call; 0.5 seconds for other DSC calls.)

1.3.3 Automatic acknowledge on/off

The automatic acknowledge feature of the DSC/watch receiver automatically

transmits the acknowledge back (ACK BQ) signal to the sending station when an

individual, position or polling call is received. (For position and polling calls,

respective item on the AUTO ACK menu must be turned on to enable automatic

acknowledge.) Automatic acknowledge can be turned on or off at the standby

display by pressing the SHIFT and 5 keys in this order.

The message AUTO ACK or MANUAL ACK appears at the bottom of the

standby display with each press of the keys.

Note 1: To give priority to own ship's communications while own ship is

communicating, show MANUAL ACK by the above procedure.

Note 2: Automatic acknowledge is not possible under the following conditions:

Priority: Distress, Urgency or Safety

Com Type: Fax, Data, No Info

Com Freq: No Info

Off Hook

1. OPERATIONAL OVERVIEW

1-12

1.4 Priority

If one or more remote stations are installed, the transceiver unit (main unit) has

the highest priority. You can interrupt remote station operation at any time with

the handset of the main unit. When you hook off the handset of the main unit,

“OCCUPIED FM8800” is indicated on all remote stations.

Each remote station has its own priority. The remote station ID (1-4) indicates its

priority. The priority of the system is as follows.

DSC of main unit > Wing handset > Handset of main unit > 1 > 2 > 3 > 4

If you hook off No.4 remote station, for example, “Occupied Handset.4” is

displayed on other remote stations. However, you can hook off and use No.1

handset.

How to set priority of the remote station

Two persons are required to set priority on a remote station, one at the main unit

and one at the remote station.

1. Turn off the power at the main unit.

2. While pressing the MENU key of a remote station, turn the VOLUME/

POWER control clockwise on the main unit to turn on the power.

Version No.

0550216-01.00

Now ID=01

Input

New ID (1-4)=

3. Press 1, 2, 3, or 4 key on the remote handset as appropriate followed by the

ENT key.

4. Turn off and on the power.

2-1

2. DSC DISTRESS COMMUNICATION

2.1 Distress Alert Transmission from the DISTRESS

Key

If a distress situation occurs, do as follows:

1. Open the DISTRESS key cover and press the DISTRESS key more than

three seconds. The alarm sounds and the red lamp in the key blinks. The

lamp will light steadily three seconds later and at the same time the distress

alert is transmitted for three seconds.

The screen changes as follows.

1) When the DISTRESS key is pressed and held down,

** Compose message **

CALL TYPE: DISTRESS

NATURE: UNDESIGNATED

POS : 12° 34N 123 ° 45E

AT : 12 : 34

Distress button

Pressed!

KEEP PRESSED FOR 3S

2) After the timer counts down to zero, “distress call in progress” is announced.

** Compose message **

CALL TYPE: DISTRESS

NATURE: UNDESIGNATED

POS : 12° 34N 123 ° 45E

AT : 12 : 34

Distress Call

in Progress on CH70.

2. DSC DISTRESS COMMUNICATION

2-2

3) The screen changes to “distress acknowledge (DIST ACK) waiting” display.

** Compose message **

CALL TYPE: DISTRESS

NATURE: UNDESIGNATED

POS : 12° 34N 123 ° 45E

AT : 12 : 34

Waiting for distress

acknowledgement.

CH16 Now available.

TIME TO GO : 4M 12S

4) When the DIST ACK is received,

Distress acknowledge

received.

FROM : 003456789

ID IN DIST : 123456789

CANCEL ALARM

TCmd : DISTRESS ACK

AT : 12 : 34

POS : 12

SIMP TP

NATURE : Piracy

° 34N 123 ° 45E

Note: If you do not receive the distress alert acknowledge call, the equipment

automatically re-transmits the distress alert and then awaits the

distress alert acknowledge call. This is repeated until the distress alert

is acknowledged.

2. Press the CANCEL or ENT key. The screen changes as follows.

** Received Message **

APR08/’04 18:30 ECC : OK

TCmd : DISTRESS ACK

DISTRESS ACK

NATURE : Piracy

POS : 12° 34N 123 ° 45E

AT : 12 : 34

FROM : 003456789

ID IN DIST : 123456789

PRESS ENT

2. DSC DISTRESS COMMUNICATION

2-3

3. Press the ENT key. The standby display with CH16 and Hi appears.

4. Provide the following information to the coast station, using a handset on the

transceiver unit or remote stations (if connected):

Distress call

(1) Speak slowly and distinctly, “MAYDAY, MAYDAY, MAYDAY,” pronounced as

the French expression “m’aider.”

(2) This is; "the name of your vessel and call sign" three times.

Then, begin the distress communications, which consists of:

Distress communications

(1) Position in latitude and longitude;

(2) The nature of the distress;

(3) The kind of assistance desired;

(4) Any other information which might facilitate rescue, for example, length, color,

and type of vessel, number of persons on board.

(5) Indicate the end of message by saying “Over.”

Some countries do not have sea area "A." In this case “ACK” from the coast

station does not arrive over DSC. A ship nearby will contact the vessel in

distress over CH16. After transmitting the distress alert, conduct voice

distress communications as shown above.

Note: To return to normal mode, turn off the power and on again.

2.2 Distress Alert Transmission with Nature of

Distress

If you want to transmit the distress alert with nature of distress specified, do as

follows:

1. Open the DISTRESS key cover and press the DISTRESS key momentarily.

The alarm sounds and the red lamp in the key blinks and after releasing the

key within three seconds the alarm stops and the red lamp goes off. The

following screen appears.

2. DSC DISTRESS COMMUNICATION

2-4

2. Rotate the channel knob to choose the nature of distress. On the remote

handset, press the up or down arrow key.

3. Press the ENT key. The screen changes as follows.

** Compose Message **

CALL TYPE : DISTRESS

NATURE : Flooding

134

30’ E

AT : 08 : 00

POS : 34

41’ N

The own ship's position and current time in UTC are displayed if your

FM-8800D/S is connected to a navigation equipment, for example, GPS.

4. Press the DISTRESS key more than three seconds.

Distress button

Pressed!

NATURE : Piracy

POS : 12

34N 123

45E

AT : 12 : 34

KEEP PRESSED FOR 3S

The distress alert with nature of distress, ship's position and time are transmitted.

The sequence of display and procedures are the same as in paragraph 2.1.

2.3 Distress Alert Transmission from CALL Key

You can transmit the distress alert with nature of distress by using CALL key.

1. Press the CALL key.

** Compose Message **

CALL TYPE : COAST CALL

TO : COAST AAA

COAST ID : 003456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 12

* Compose Message *

CALL TYPE :

COAST CALL

Transceiver unit screen Remote handset screen

2. DSC DISTRESS COMMUNICATION

2-5

2. Press the ENT key to show the call type selection window.

3. Rotate the CH knob (or press up / down arrow key) to choose DISTRESS.

Press the ENT key.

** Compose Message **

NATURE : UNDESIGNATED

CALL TYPE : DISTRESS

POS : 12

34N 123

45E

AT : 12 : 34

SIMP TP

4. Press the ENT key to display the distress nature list.

5. Rotate the CH knob (or press up / down arrow key) to choose nature of

distress and press the ENT key.

6. Press the ENT key to show the position setup window.

INPUT TYPE : AUTO

LAT : 34

LON : 134

30 E

TIME : 08 : 00

41 N

AUTO

MANUAL*

NO INFO

*: MANUAL can not be

chosen if position data

is input.

7. After confirming the ship's position and time, press the DISTRESS key more

than three seconds to transmit the distress alert.

2. DSC DISTRESS COMMUNICATION

2-6

2.4 Canceling a False Distress Alert

If you have transmitted a distress alert by mistake, do the following to cancel it

1. Switch off equipment immediately.

2. Switch equipment on and set to Channel 16.

3. Transmit message to “All Stations” giving your vessel's name,

call sign and DSC number.

Example message

All Stations, All Stations, All Stations

This is VESSEL'S NAME, CALLSIGN,

DSC NUMBER, POSITION.

Cancel my distress alert of DATE, TIME, UTC.

=Master, VESSEL'S NAME, CALLSIGN.

DSC NUMBER, DATE, TIME UTC.

2.5 Receiving Distress Alert from Other Vessel,

Transmitting DIST ACK Signal

In no case is a ship permitted to transmit a DSC distress relay call upon receipt

of a DSC distress alert on VHF channel 70.

Procedure when in area A1

1. When the FM-8800D/8800S receives a distress alert from another vessel, the

ALARM LED (red) blinks and the FM-8800D/8800S sounds the distress

alarm.

2. Silence the alarm by pressing the CANCEL key.

3. Wait up to five minutes until the DIST ACK signal from a coast station is

received. Be prepared to follow the instructions of the coast station.

4. If you do not receive the DIST ACK signal, follow the flow chart shown on

page 2-8 to determine if your vessel should acknowledge a distress alert.

If further DSC alerts are received from the same source and the ship in distress

is beyond doubt in the vicinity, a DSC acknowledgement may, after consultation

with an Rescue Co-ordination Center (RCC) or Coast Station, be sent to

terminate the distress call.

Note 1: An asterisk (*) in a received distress alert message indicates error or

unknown at the location marked with the asterisk.

Note 2: Do not send DIST ACK in response to receipt of distress alert having the

nature of distress as “EPIRB emission”.

2. DSC DISTRESS COMMUNICATION

2-7

About 20 to 30 miles

(Sea area A1)

Your Ship

Coast station

Distress Alert

Transmission

Vessel in Distress

Receiving distress alert from other vessel

2. DSC DISTRESS COMMUNICATION

2-8

Flow chart for determining if you should/should not transmit DIST ACK signal

Press [CANCEL]

key to silence alarm.

DSC Distress alert received.

Listen on CH16 for

5 minutes.

Did you receive

acknowledge from

CS and/or RCC?

Is own

vessel able

to assist?

Is distress traffic

in progress?

Is distress call

continuing?

Acknowledge the alert by

radiotelephony to the ship

in distress on VHF CH16.

Yes

Inform CS and/or RCC.

Yes

Yes Yes

Enter details in log.

CS = Coast Station

RCC = Rescue Co-ordination Center

1. Say "MAYDAY" ONCE.

2. Say ID number of vessel

in distress THREE TIMES.

3. Say "This is" (your vessel's

name) ONCE.

4. Say ID number of your vessel

THREE TIMES.

5. Say "Received MAYDAY"

ONCE.

2. DSC DISTRESS COMMUNICATION

2-9

Transmitting DIST ACK over CH16

Select VHF CH16 and transmit DIST ACK to vessel in distress.

Relay the distress alert to a coast station over DSC.

Follow the instructions of the coast station.

Transmit DIST ACK to vessel in

distress over DSC CH70. Communicate with vessel in distress.

No reply Reply received

Begin search and rescue operation for the vessel in distress.

Transmitting DIST ACK signal

If your vessel meets the requirements necessary to transmit the DIST ACK

signal, do the following:

When a distress alert from other ship is received, the following screen appears.

The alarm sounds and the ALARM lamp blinks.

Distress

Call received.

NATURE : UNDESIGNATED

POS : 12

34’N 123

45’E

AT : 12 : 34

ID IN DIST : 123456789

CANCEL ALARM

SIMP TP

2. DSC DISTRESS COMMUNICATION

2-10

1. Press the CANCEL or ENT key to silence the alarm. The following message

appears.

** Received Message **

MAY10/’04 08:03 ECC : OK

NATURE : UNDESIGNATED

DISTRESS

POS : 12

34’N 123

45’E

AT : 12 : 34

ID IN DIST : 123456789

PRESS ENT TO ACK

SIMP TP

2. If you do not receive DIST ACK from coast station within five minutes and

your vessel meets requirements (see previous page) for transmitting DIST

ACK, press the ENT key, and then press the CALL key more than three

seconds to transmit the DIST ACK.

** Send Message **

DISTRESS ACK

TO : 123456789

TCmd : DISTRESS ACK

NATURE : UNDESIGNATED

POS : 12

34’N 123 45’E

AT : 12 : 34

SIMP TP

PRESS CALL TO SEND

After transmitting the DIST ACK, the standby display appears.

After transmitting DIST ACK

Begin search and rescue operations for the vessel in distress, communicating

with the vessel over CH16 (automatically set). Relay distress alert to coast

station by DSC following the instruction in the next paragraph. Finally, follow the

instructions of the coast station.

2. DSC DISTRESS COMMUNICATION

2-11

2.6 Sending Distress Relay on Behalf of a Ship in

Distress

When you should relay a distress alert

You may relay a distress alert in the following conditions:

1) When the station in distress is not itself in a position to transmit the distress

message, or

2) When the master or person responsible for the vessel not in distress, or the

person responsible for the coast station, considers that further help is

necessary.

DO NOT press the DISTRESS key to relay a distress alert; it is for use

when own vessel is in distress.

2.6.1 Sending distress relay to coast station

1. Press the CALL key. The [Compose message] screen appears.

** Compose Message **

CALL TYPE : COAST CALL

COAST ID : 003456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CHANNEL : 10

2. Press the ENT key. The CALL TYPE selection window appears.

3. Rotate the CH knob (or press up / down arrow key) to choose RELAY SEL.

2. DSC DISTRESS COMMUNICATION

2-12

4. Press the ENT key.

5. Press the ENT key again. The COAST ID entry window appears.

6. Key in a coast station ID with numeric keys and press the ENT key.

7. Press the ENT key again. The ID IN DIST entry window appears.

8. Key in the ID number of ship in distress with numeric keys and press the ENT

key. If you do not know the ID, simply press the ENT key without entering ID;

NO INFO is displayed.

9. Press the ENT key and the list of distress nature appears.

10. Rotate the CH knob to choose a nature of distress (if known) and press the

ENT key twice. If you do not know the nature of distress, choose

UNDESIGNATED.

11. Enter position of the ship in distress, following 1), 2) or 3) below.

AUTO

MANUAL

NO INFO

1) For automatic input, press the ENT key twice. Go to step 12.

2) For manual input, press the ENT key to open the INPUT TYPE menu,

rotate the CH knob to choose MANUAL and then push the ENT key.

Enter latitude and longitude of ship in distress and time as follows:

a) Press the ENT key. Enter latitude and then press the ENT key.

b) Press the ENT key. Enter longitude and then press the ENT key.

c) Press the ENT key. Enter UTC time and then press the ENT key. Go to

step 12.

Note: If you cannot confirm time, enter 88:88 to input NO INFO as the

time.

3) If you cannot confirm position of ship in distress, press the ENT key to

open the INPUT TYPE menu, rotate the CH knob to choose NO INFO and

then press the ENT key. Go to step 12.

2. DSC DISTRESS COMMUNICATION

2-13

12. Press the CALL key more than three seconds to transmit the distress relay.

KEEP PRESSED FOR 3S

** Compose Message **

CALL TYPE : RELAY SEL

TCmd : DISTRESS RELAY

ID IN DIST : NO INFO

COAST ID :

NATURE : UNDESIGNATED

POS : 12° 34N 123 ° 45E

AT : 12 : 34

SIMP TP When CALL key is pressed,

this message appears and

timer counts down.

The message will be transmitted and “Waiting for acknowledgement” will appear.

2.6.2 Sending distress relay to all ships

1. Press the CALL key. The [Compose message] screen appears.

** Compose Message **

CALL TYPE : COAST CALL

COAST ID : 003456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CHANNEL : 10

2. Press the ENT key. The CALL TYPE selection window appears.

3. Rotate the CH knob (or press up / down arrow key) to choose RELAY ALL.

SHIP CALL

GROUP CALL

PSTN CALL

ALL SHIPS

AREA CALL

POSITION

COAST CALL POLLING

NEUTRAL

MEDICAL

RELAY ALL

RELAY SEL

DISTRESS

2. DSC DISTRESS COMMUNICATION

2-14

4. Press the ENT key.

5. Press the ENT key again. The ID IN DIST entry window appears.

6. Key in the ID number of ship in distress with numeric keys and press the ENT

key. If you do not know the ID, simply press the ENT key without entering ID;

NO INFO is displayed.

7. Press the ENT key and the list of distress nature appears.

8. Rotate the CH knob (or press up / down arrow key) to choose a nature of

distress (if known) and press the ENT key twice. If you do not know the

nature of distress, choose UNDESIGNATED.

9. Enter position of the ship in distress, following 1), 2) or 3) below.

AUTO

MANUAL

NO INFO

1) For automatic input, press the ENT key twice. Go to step 10.

2) For manual input, press the ENT key to open the INPUT TYPE menu,

rotate the CH knob to choose MANUAL and then push the ENT key. Enter

latitude and longitude of ship in distress and time as follows:

a) Press the ENT key. Enter latitude and then press the ENT key.

b) Press the ENT key. Enter longitude and then press the ENT key.

c) Press the ENT key. Enter UTC time and then press the ENT key. Go to

step 10.

Note: If you cannot confirm time, enter 88:88 to input NO INFO as the

time.

3) If you cannot confirm position of ship in distress, press the ENT key to

open the INPUT TYPE menu, rotate the CH knob to choose NO INFO and

then press the ENT key. Go to step 10.

2. DSC DISTRESS COMMUNICATION

2-15

10. Press the CALL key to transmit the call.

** Compose Message **

CALL TYPE : RELAY ALL

TCmd : DISTRESS RELAY

ID IN DIST :

NATURE : UNDESIGNATED

POS : 12

34N 123

45E

AT : 12 : 34

SIMP TP

KEEP PRESSED FOR 3S

When CALL key is pressed,

this message appears and

timer counts down.

After the call is transmitted, the standby display appears.

2.7 Receiving Distress Relay

2.7.1 Receiving distress relay all call

If you receive a distress relay for all ships, continue monitoring CH16.

1. When a distress relay all ships call is received, the audio alarm sounds and

the display looks like the one below.

Distress relay all

call received.

ID IN DIST : 234567890

TCmd : DISTRESS RELAY

FROM : 123456789

NATURE : UNDESIGNATED

POS : 12° 34N 123° 45E

SIMP TP

AT : 12 : 34

CANCEL ALARM

2. DSC DISTRESS COMMUNICATION

2-16

2. Press the CANCEL key or ENT key to silence the alarm and the display

changes as below.

*ReceivedMessage*

APR01/í0412:34ECC:OK

TCmd:DISTRESSRELAY

DISTRESSRELAYALL

NATURE:UNDESIGNATED

POS:12 °34N123 °45E

AT:12:34

SIMPTP

IDINDIST:234567890

FROM:123456789

PRESSENT

3. Press the ENT key to return to the standby display with CH16.

4. Watch CH16.

2.7.2 Receiving distress relay from coast station

If you receive a distress relay call from a coast station, continue monitoring

CH16.

1. When a distress relay call from a coast station is received, the audio alarm

sounds and the display looks like the one below.

Distressrelayall

callreceived.

IDINDIST:123456789

TCmd:DISTRESSRELAY

NATURE:UNDESIGNATED

POS:12

34N123

45E

SIMPTP

AT:12:34

CANCELALARM

FROM:003456789

2. DSC DISTRESS COMMUNICATION

2-17

2. Press the CANCEL key to silence the alarm and the display changes as

below.

**ReceivedMessage**

APR01/í0412:34ECC:OK

NATURE:UNDESIGNATED

DISTRESSRELAYALL

POS:12 °34N123 °45E

AT:12:34

SIMPTP

IDINDIST:123456789

FROM:003456789

TCmd:DISTRESSRELAY

PRESSENT

3. Press the ENT key to return to the standby display with CH16.

4. Watch CH16.

2. DSC DISTRESS COMMUNICATION

2-18

This page is intentionally left blank.

3-1

3. DSC OPERATION FOR

NON-DISTRESS CASES

3.1 Coast or Ship Call

The coast or ship call is for sending message to a specific coast or ship station. After

transmitting message (called ACK RQ transmission), wait to receive the

acknowledge back (ACK BQ) signal from the receiving station. You should receive it

within five minutes.

Own Ship Coast Station

d Acknowledge back

(ACK BQ signal)

c Individual call

(ACK RQ transmission)

How a coast or ship call is transmitted

General procedure for transmitting a coast or ship call

Load saved Tx message, or prepare

message.

Transmit message.

Receive ACK BQ from receiving station.

Communicate with station.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-2

3.1.1 Sending a coast or ship call

1. Press the CALL key. The display changes from the standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

**ComposeMessage**

CALLTYPE:COASTCALL

TO:COASTAAA

COASTID:003456789

ROUTINE

TCmd1:SIMPLEXTP

TCmd2:NOINFO

CH:12

*ComposeMessage*

CALLTYPE:

COASTCALL

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose COAST CALL

or SHIP CALL and press the ENT key.

4. ID is selected; press the ENT key.

5. Key in a coast ID or ship ID number as appropriate and press the ENT key.

6. ROUTINE is selected; press the ENT key.

7. Choose ROUTINE, BUSINESS, SAFETY, or URGENCY as appropriate

followed by pressing the ENT key.

8. TCmd1 is selected; press the ENT key.

9. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX as appropriate followed by

pressing the ENT key. If you chose SIMPLEX, DUPLEX or FAX, NO INFO

appears in the Tcmd2 field. Go to step 12. If you chose DATA, go to the next

step.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-3

10. TCmd2 is selected; press the ENT key.

V. 26 ter

V. 27 ter

V. 32

V. 21

V. 22

V. 22 bis

V. 23

V. 26 bis

11. Choose the data type and press the ENT key.

12. Choose CH and press the ENT key. The following window appears.

SELECT CH

NO INFO

13. Choose SELECT CH or NO INFO as appropriate followed by pressing the

ENT key. If you chose SELECT CH, the following channel list appears. (The

example shown is the international, duplex channel list.) Rotate the CH knob

(or press up / down arrow key) to choose a channel you wish to communicate

over and then press the ENT key.

DUP CHANNEL

14. Press the CALL key more than three seconds to transmit the message.

3.1.2 Receiving acknowledgement of coast or ship call

1. After a coast or ship call is sent, the equipment waits for acknowledgement of

the call, showing the display below.

Waiting for

acknowledgement.

COAST ID : 003456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 12

TIME TO GO : 3M30 S

The timer starts counting down the maximum time to wait for acknowledgement,

five minutes.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-4

2. One of the following three messages appears. "No response! Try calling

again?" appears after the timer counts down to zero. It means the receiving

station did not respond.

Able acknowledge

call received.

FROM : 003456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 12

Unable acknowledge

call received.

FROM : 003456789

NO REASON

CANCEL ALARM

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 12

CANCEL ALARM

Able acknowledge call received Unable acknowledge call received

No response!

Try calling again?

COAST ID : 003456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 12

PRESS ENT

No response from station

A reason of Unable acknowledge is displayed. In case of QUEUE INDICATION,

the channel will change to one that the coast station specifies.

3. Do one of the following depending on the message shown above.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-5

Able acknowledge call received

a) The audio alarm sounds; press the CANCEL key to silence it, and the display

changes as below.

**ReceivedMessage**

APR01/í0412:34ECC:OK

COASTACK

PRESSENT

ROUTINE

TCmd1:SIMPLEXTP

TCmd2:NOINFO

CH:12

FROM:003456789 Ifafileisregistered,

itsregistrationname

isdisplayedinstead

ofID.

b) Press the ENT key to go to the standby display. The working channel is

automatically set; you may start voice communications.

Unable acknowledge call received

a) The alarm sounds; press the CANCEL key to silence the alarm.

b) Send the call again later.

No response! Try calling again?

Re-send call: Push the ENT key followed by pressing the CALL key.

You can re-send the message from the TRANSMITTED log. See “3.10 Log

File.”

Cancel call: Press the CANCEL key to go to the standby display.

3.1.3 Receiving a coast or ship call

When own ship receives a coast or ship call, acknowledgement is automatically

or manually sent depending on the comply-type setting (see paragraph 4.2). The

relationship between comply status and automatic/manual acknowledge is as

shown in the table below.

Note: The handset must be on hook to enable automatic acknowledge.

Comply status

Setting of 5 ACQ key

ABLE UNABLE

AUTO ACK Can send acknowledge

automatically.

Can send UNABLE

automatically.

MANUAL ACK Can send acknowledge

manually

Can send UNABLE

manually.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-6

Acknowledgement the call automatically or manually by doing one of the

following:

1) Send automatic acknowledge (ACK BQ) with comply status “ABLE.” See the

procedure below.

2) Sending automatic acknowledge (ACK BQ) with comply status "UNABLE."

See the procedure on page 3-7.

3) Manually acknowledging individual call with "ABLE." See the procedure on

page 3-8.

4) Manually acknowledging a coast or ship call with "UNABLE." See the

procedure on page 3-9

1) Sending automatic acknowledge (ACK BQ) with comply status "ABLE."

1. When the automatic acknowledge feature is active (AUTO ACK), the comply

status is "ABLE" and a coast or ship call is received, the auto acknowledge

(ACK BQ) call is sent immediately. The display shown below appears. The

alarm sounds and the ALARM LED blinks two minutes.

Able acknowledge

transmitted!

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 08

CANCEL ALARM

2. Press the CANCEL key to silence the alarm. The following display appears.

** Send Message **

PRESS ENT

COAST ACK

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 08

TO SHIP : 123456789

3. Press the ENT key. You can now communicate with the party, over the VHF

channel specified.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-7

2) Sending automatic acknowledge (ACK BQ) with comply status

"UNABLE."

1. When the automatic acknowledge feature is active (AUTO ACK), the comply

status is "UNABLE" and a coast or ship call is received, the display shown

below appears, indicating that the auto acknowledge call with UNABLE (ACK

BQ) has been sent. The alarm sounds and the ALARM LED blinks two

minutes.

Unable acknowledge

transmitted.

ROUTINE

TCmd1 : UNABLE

TCmd2 : BUSY

CANCEL ALARM

CH : NO INFO

2. Press the CANCEL key to silence the alarm. The following display appears.

** Send Message **

COAST BQ

TO : 123456789

ROUTINE

TCmd1 : UNABLE

TCmd2 : BUSY

CH : NO INFO

PRESS ENT

3. Press the ENT key.

4. Then, prepare a message and sent it following the procedures shown on in

paragraph 3.1.1.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-8

3) Manually acknowledging individual call with "ABLE."

1. When the equipment is set up with manual acknowledge (MANUAL ACK), the

comply status is "ABLE" and a coast or ship call is received, the alarm sounds

and the display looks like the one below.

Individual request

call received.

FROM : 123456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CHANNEL : CH08

CANCEL ALARM

2. Press the CANCEL key to silence the alarm. The following display appears.

** Received Message **

APR01/04 12 : 34 ECC : OK

SHIP CALL

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : CH08

FROM : 123456789

PRESS ENT TO ACK

3. To send the ACK BQ manually, press the ENT key. The pop-up window

shown below is displayed.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-9

4. Choose ABLE and press the ENT key. The display changes as shown below.

** Send Message **

PRESS CALL TO SEND

SHIP ACK

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 08

TO : 123456789

5. Press the CALL key more than three seconds to transmit the ACK BQ. The

display changes to the standby display with a channel specified.

4) Manually acknowledging a coast or ship call with "UNABLE."

1. When the equipment is set up with manual acknowledge and an individual call

is received, the alarm sounds and the display shows the message "Individual

request call received."

Individual request

call received.

FROM : 123456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CHANNEL : CH08

CANCEL ALARM

2. Press the CANCEL key to silence the alarm. The following display appears.

** Received Message **

APR01/04 12 : 34 ECC : OK

SHIP CALL

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : CH08

FROM : 123456789

PRESS ENT TO ACK

3. DSC OPERATION FOR NON-DISTRESS CASES

3-10

3. To send the ACK BQ manually, press the ENT key. The pop-up window

shown below is displayed.

4. Choose UNABLE and press the ENT key. The following pop-up screen

appears.

NO REASON

BUSY

EQUIP DISBLD

MODE UNAVAIL

CH UNAVAIL

5. Press the ENT key and the entry window of working channel appears.

6. Key in a working channel and press the ENT key.

** Send Message **

SHIP ACK

ID : 123456789

TCmd1 : UNABLE

TCmd2 : NO REASON

CH : NO INFO

PRESS CALL TO SEND

ROUTINE

7. Press the CALL key more than three seconds to transmit the ACK BQ. The

display changes to the standby display with channel specified.

3.2 Group Call

A group call is for calling a specific group by specifying its group ID.

Up to 20 group IDs can be registered. When you set the group call in a message

file, its group ID is stored automatically (see paragraph 4.5). To confirm group

IDs, open the SYSTEM menu.

3.2.1 Sending a group call

1. Press the CALL key. The display changes to the COMPOSE MESSAGE

screen and the CALL TYPE is displayed in reverse video.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-11

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose GROUP CALL

and press the ENT key.

4. GROUP ID is selected; press the ENT key.

5. Key in a group ID and press the ENT key.

6. ROUTINE is selected; press the ENT key.

7. Choose ROUTINE, BUSINESS, SAFETY, or URGENCY as appropriate

followed by pressing the ENT key.

8. TCmd1 is selected; press the ENT key.

9. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX followed by pressing the

ENT key. If you chose SIMPLEX, DUPLEX, or FAX, NO INFO appears in the

Tcmd2 field. Go to step 12. If you chose DATA, go to the next step.

10. TCmd2 is selected; press the ENT key.

V. 26 ter

V. 27 ter

V. 32

V. 21

V. 22

V. 22 bis

V. 23

V. 26 bis

11. Choose the data type and press the ENT key.

12. Choose CH and press the ENT key. The following window appears.

SELECT CH

NO INFO

3. DSC OPERATION FOR NON-DISTRESS CASES

3-12

13. Choose SELECT CH or NO INFO as appropriate followed by pressing the

ENT key. If you chose SELECT CH, the following channel list appears. (The

example shown is the international, duplex channel list.) Rotate the CH knob

(or press up / down arrow key) to choose a channel you wish to communicate

and press the ENT key.

DUP CHANNEL

14. Press the CALL key more than three seconds. A message will be

transmitted.

3.2.2 Receiving a group call

Group ID must be registered in order to receive a group call. See paragraph 4.5.

1. When a group call is received, the alarm sounds and the ALARM LED blinks

two minutes.

Group

call received.

FROM : 123456789

TO : 0234567

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : CH08

CANCEL ALARM

2. Press the CANCEL or ENT key to silence the alarm. The following display

appears.

** Received Message **

GROUP CALL EOS

APR01/04 12 : 34 ECC : OK

FROM : 123456789

TO : 023456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : CH08

PRESS ENT TO CHANGE CH

3. Press the ENT key. You can now communicate with the party, over the VHF

channel specified.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-13

3.3 PSTN Call

The PSTN call allows the making and receiving of telephone calls over public

switched telephone networks. To use the PSTN call feature, use a handset

which has a HOOK ON/OFF function. The standard supply handset has this

feature.

3.3.1 Sending a PSTN call

1. Press the CALL key. The display changes from standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose PSTN CALL

and press the ENT key.

** Compose Message **

CALL TYPE : PSTN CALL

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

NAME :

TEL :

COAST ID : 003456789

If MMSI is registered

in a file, its file name

is displayed. If not,

this field is blank.

4. COAST ID is selected; press the ENT key.

5. Key in a coast ID and press the ENT key.

6. TCmd1 is selected; press the ENT key.

7. Choose SIMPLEX or DUPLEX as appropriate followed by pressing the ENT

key.

8. TEL is selected; press the ENT key.

9. Key in a subscriber's telephone number (max. 16 digits).

10. Press the CALL key more than three seconds.

Call in progress

on CH70

COAST ID : 003456789

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

NAME : FURUNO

TEL : 81798631131

TIME TO GO : 5S

When TEL no. is registered,

the registered name is displayed.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-14

If a response from the coast station is received within five seconds, transmit

PSTN CALL (EOS) signal and then carrier frequency during two seconds. Then

your phone rings. Press the CANCEL key to stop the calling sound and change

to standby display. Hook off and communicate with other party.

Note: If using a hand-microphone, pressing the CANCEL key is equal to

off-hook.

3.3.2 PSTN call disconnection (ship disconnects line)

1. After hanging up the handset or pressing the CANCEL key to complete your

call, the display shows the following message. The end of call signal is

transmitted; and the system then waits for a response from the coast station.

2. When the ACK from the coast station is received, the following display

appears. The communication time (charge time) is informed.

FROM : 003456789

TEL : 1234567890123456

CHARGE TIME : 00h05m18s

Able acknowledge

call received.

PRESS ENT

3. DSC OPERATION FOR NON-DISTRESS CASES

3-15

3.3.3 PSTN call disconnection (coast station disconnects line)

1. The PSTN line is disconnected by the coast station when it finds no evidence

of communications or the land subscriber hangs up. The coast station then

sends charge information as below.

FROM : 003456789

TEL : 1234567890123456

CHARGE TIME : 00h06m18s

PSTN end of call

received.

PRESS ENT

3.3.4 Receiving a PSTN call

1. When a PSTN call is received, the following display appears. Your phone

rings.

2. Hook off within 60 seconds. The channel changes automatically and you can

communicate with other party.

3. When the communication is completed, hook on the handset or press the

CANCEL key.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-16

3.4 All Ships Call

When an urgent but not life-endangering situation arises on your ship, for

example, engine trouble, send an all ships call to request assistance.

After sending the call, you can communicate by voice over the radiotelephone.

Do the following before beginning actual communications:

URGENCY priority: Say PAN three times followed by your call sign.

SAFETY priority: Say SECURITE three times followed by your call sign.

Own Ship

Coast

Station

3.4.1 Sending an all ships call

1. Press the CALL key. The display changes from standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose ALL SHIPS and

press the ENT key.

4. SAFETY is selected; press the ENT key.

5. Choose SAFETY, URGENCY, or DISTRESS as appropriate followed by

pressing the ENT key.

6. TCmd1 is selected; press the ENT key.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-17

7. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX as appropriate followed by

pressing the ENT key. If you chose SIMPLEX, DUPLEX, or FAX, the NO

INFO appears in the Tcmd2 field. Go to the step 12. If you chose DATA, go to

the next step.

8. TCmd2 is selected; press the ENT key.

V. 26 ter

V. 27 ter

V. 32

V. 21

V. 22

V. 22 bis

V. 23

V. 26 bis

9. Choose the data type and press the ENT key.

10. Choose CH and press the ENT key. The following window appears.

SELECT CH

NO INFO

11. Choose SELECT CH or NO INFO as appropriate followed by pressing the

ENT key. If you chose SELECT CH, the following channel list appears. (The

example is the international, duplex channel list.) Rotate the CH knob (or

press up / down arrow key) to choose a channel and press the ENT key.

DUP CHANNEL

12. Press the CALL key more than three seconds to transmit the call.

After transmitting the message, the screen changes to standby display.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-18

3.4.2 Receiving an all ships call

In case of ON HOOK

1. When an all ships call is received, the audio alarm sounds and the display

looks something like the one shown below.

All ships

call received.

FROM : 123456789

SAFETY

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 16

CANCEL ALARM

2. Press the CANCEL or ENT key to silence the alarm. The display changes as

follows.

** Received Message **

APR01/04 12 : 34 ECC : OK

ALL SHIPS CALL

SAFETY

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 16

FROM : 123456789

PRESS ENT TO CHANGE CH

3. Press the ENT key. The display changes to the standby display, and you can

watch the contents of the message.

In case of OFF HOOK

1. When an all ships call is received, the audio alarm sounds and the ALARM

LED blinks.

2. Press the ACK key. The display changes the standby display, indicating

channel specified.

3. Press the CANCEL key. The audio alarm stops and the display changes to

the receive message display.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-19

3.5 Geographical Area Call

The geographical area call is for sending a call to all ships within the area you

designate in your geographical area call. In the figure below, for example, the

call will be sent to all ships within 24-34°N, 135-140°W.

Reference point

(For example,

34°N 140°W)

5°

140°W135°W

10°

34°N

24°N

3.5.1 Sending a geographical area call

1. Press the CALL key. The display changes from standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose AREA CALL

and press the ENT key.

4. AREA is selected; press the ENT key.

5. Using the numeric keys, enter latitude and longitude of reference point and

southerly degrees and easterly degrees of area. To change coordinate,

choose it and press the 1 key for North or East; 2 key for South or West. After

entering data, push the ENT key.

6. ROUTINE is selected; press the ENT key.

7. Choose ROUTINE, BUSINESS, SAFETY, URGENCY, or DISTRESS as

appropriate followed by pressing the ENT key.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-20

8. TCmd1 is selected; press the ENT key.

9. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX as appropriate followed by

pressing the ENT key. If you chose SIMPLEX, DUPLEX, or FAX, NO INFO

appears in the Tcmd2 field. Go to step 12. If you chose DATA, go to the next

step.

10. TCmd2 is selected; press the ENT key.

V. 26 ter

V. 27 ter

V. 32

V. 21

V. 22

V. 22 bis

V. 23

V. 26 bis

11. Choose the data type and press the ENT key.

12. Choose CH and press the ENT key. The following window appears.

SELECT CH

NO INFO

13. Choose SELECT CH or NO INFO as appropriate followed by pressing the

ENT key. If you chose SELECT CH, the following channel list appears. (The

example is the international, duplex channel list.) Rotate the CH knob (or

press up / down arrow key) to choose a channel and press the ENT key.

DUP CHANNEL

14. Press the CALL key more than three seconds to transmit the message. After

the call is transmitted, the standby display appears with channel specified.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-21

3.5.2 Receiving a geographical area call

1. When a geographical area call is received, the alarm sounds and the ALARM

LED blinks five seconds.

Geographical area

call received.

FROM : 123456789

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 10

CANCEL ALARM

AREA : 12

N 123

↓

°→

2. Press the CANCEL key to silence the alarm. The following display appears.

** Received Message **

APR01/04 12 : 34 ECC : OK

AREA CALL

ROUTINE

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

CH : 10

FROM : 123456789

AREA : 12

N 123

↓

°→

PRESS ENT TO CHANGE CH

3. Press the ENT key. You can now watch over the VHF channel specified.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-22

3.6 Position Call

There are two types of position calls: other station requires your ship's position

and your ship requests position of another ship.

Finding position of other station

Sending own ship's position to other station

OtherStation

OwnStation

3.6.1 Position call: requesting other ship's position

1. Press the CALL key. The display changes from standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose POSITION and

press the ENT key.

**ComposeMessage**

CALLTYPE:POSITION

REQUEST

TO:

SHIPID:123456789

ROUTINE

TCmd1:POSITIONREQUEST

TCmd2:NOINFO

Ifafileisregistered,

itsregistrationname

isdisplayed.

Ifnot,thisfieldisblank.

4. SHIP ID is selected; press the ENT key.

5. Key in a ship ID for which you want to know its position.

6. ROUTINE is selected; press the ENT key.

7. Choose ROUTINE, BUSINESS, SAFETY, URGENCY, or DISTRESS as

appropriate followed by pressing the ENT key.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-23

8. Press the CALL key more than three seconds to transmit position request.

The following display appears. The timer counts down until a response is

received.

Waiting for

acknowledgement.

SHIP ID : 123456789

ROUTINE

TCmd1 : POSITION REQUEST

TCmd2 : NO INFO

TIME TO GO : 3M30 S

If a file is registered,

its registration name

is displayed.

If not, this field is blank.

9. When an acknowledge call is received, the following display appears and the

audio alarm sounds.

Position acknowledge

received.

TCmd1 : POSITION

TCmd2 : NO INFO

FROM : 123456789

ROUTINE

CANCEL ALARM

AT 12 : 34

POS : 12

34N 123

45E

10. Press the CANCEL key to silence the alarm. The display looks as below.

You can now confirm position of other ship.

** Received Message **

APR01/04 12 : 34 ECC : OK

POSITION ACK

AT 12 : 34

TCmd1 : POSITION

TCmd2 : NO INFO

ROUTINE

FROM : 123456789

POS : 12

34N 123

45E

PRESS ENT

11. When "No response! Try calling again?" is displayed;

Re-send call: Push the ENT key followed by the CALL key.

Cancel call: Press the CANCEL key.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-24

3.6.2 Position call: other ship requests your position

You may turn automatic acknowledge of position request on or off with

POSITION CALL in the system setup menu. For further details, see page 4-3.

Automatic reply

1. When another ship requests your position, the status of the 5 ACK key is

AUTO ACK and the setting of POSITION CALL on the system setup menu is

ON, the FM-8800D/S transmits own position data, showing the display below.

Position auto ack

transmitted.

TCmd1 : POSITION

TCmd2 : NO INFO

CANCEL ALARM

AT 12 : 34

POS : 12

34N 123

45E

2. Press the CANCEL

key to silence the alarm. The display then looks like the one below, indicating

own ship's position.

** Send Message **

POSITION ACK

TCmd1 : POSITION

TCmd2 : NO INFO

AT 12 : 34

TO : 123456789

POS : 12 ° 34N 123 ° 45E

PRESS ENT

Manual reply

1. When a position request call is received and the setting of POSITION CALL

on the system setup menu is OFF, the audio alarm sounds and the display

changes as below.

Position request

call received.

TCmd1 : POSITION REQUEST

TCmd2 : NO INFO

FROM : 123456789

ROUTINE

CANCEL ALARM

3. DSC OPERATION FOR NON-DISTRESS CASES

3-25

2. Press the CANCEL key to silence the alarm.

** Received Message **

APR01/04 12 : 34 ECC : OK

POSITION CALL

TCmd1 : POSITION

TCmd2 : NO INFO

ROUTINE

FROM : 123456789

PRESS ENT TO ACK

3. To send your position manually, press the ENT key. The following pop-up

menu appears.

ANSWER

NO ANSWER

4. Choose ANSWER by the CH knob and press the CALL key to send your

position data. Then, the standby display appears.

To send no position data, choose NO ANSWER and press the ENT key twice

to return to the standby display.

3.7 Polling Call

Polling means confirming if own station is within communicating range with other

station. This function only provides affirmative or negative response; it does not

provide position information. Note that simultaneous polling to more than one

station is not possible.

1Polling

2Acknowledge

3Polling

4Acknowledge

3.7.1 Sending a polling call

1. Press the CALL key. The display changes from standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

2. Press the ENT key to open the call type list.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-26

3. Rotate the CH knob (or press up / down arrow key) to choose POLLING and

press the ENT key.

** Compose Message **

SHIP ID :

TCmd1 : POLLING

TCmd2 : NO INFO

ROUTINE

CALL TYPE : POLLING

4. SHIP ID is selected; press the ENT key.

5. Key in a station ID with the numeric keys and press the ENT key.

6. ROUTINE is selected; press the ENT key.

7. Rotate the CH knob (or press up / down arrow key) to choose the appropriate

communications category and press the ENT key.

8. Press the CALL key more than three seconds to transmit polling call. After the

call is transmitted, the following display appears. The timer counts down until

a response is received.

9-1. When a polling acknowledge call is received, the audio alarm sounds and

the display looks something like the one below.

Polling acknowledge

received.

FROM : 123456789

ROUTINE

TCmd1 :

POLLING

TCmd2 : NO INFO

CANCEL ALARM

If a file is registered, the

registration name is

displayed.

Press the CANCEL key to silence the alarm. Press the ENT key to show the

standby display when you can confirm if called party is within communicating

range.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-27

9-2. When "No response! Try calling again?" is displayed, do one of the

following:

Re-send call: Push the ENT key followed by the CALL key.

Cancel call: Press the CANCEL key to return to the standby display.

3.7.2 Receiving a polling call

Automatic reply

1. When a polling request is received and the equipment is set up for automatic

acknowledge POLLING on the AUTO ACK menu is ON and the ACK key is

set to show AUTO ACK on the display, the display changes as shown in the

illustration below and the audio alarm sounds.

Polling auto ack

transmitted.

ROUTINE

TCmd1 :

POLLING

TCmd2 : NO INFO

CANCEL ALARM

2. Press the CANCEL or ENT key to silence the alarm. The display changes as

below.

** Send Message **

POLLING ACK

TO : 123456789

ROUTINE

TCmd1 : POLLING

TCmd2 : NO INFO

PRESS ENT

3. DSC OPERATION FOR NON-DISTRESS CASES

3-28

Manual reply

1. When a polling request call is received and the setting of POLLING CALL on

the system setup menu is OFF, the display changes as shown in the

illustration below and the audio alarm sounds.

Position request

call received.

FROM : 123456789

ROUTINE

TCmd1 :

POLLING

TCmd2 : NO INFO

CANCEL ALARM

2. Press the CANCEL key to silence the alarm. The display changes as below.

** Received Message **

APR01/04 12 : 34 ECC : OK

POLLING RQ

ROUTINE

TCmd1 : POLLING REQUEST

TCmd2 : NO INFO

FROM : 123456789

PRESS ENT TO ACK

3. To respond to the call, press the ENT key. The following pop-up window

appears.

ANSWER

NO ANSWER

4. Choose ANSWER by the CH knob and press the CALL key to send the

polling acknowledge call. Then the standby display appears.

To send no reply, choose NO ANSWER and press the ENT key twice to

return to the standby display.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-29

3.8 Neutral Craft Call

The neutral craft call, which contains own ship position and ID, informs all ships

that your ship is not a participant in armed conflict. Send the call BEFORE

entering an area of armed conflict.

3.8.1 Sending a neutral craft call

1. Press the CALL key. The display changes from the standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose NEUTRAL and

press the ENT key.

** Compose Message **

CRAFT

TCmd1 : SIMPLEX TP

TCmd2 : NEUTRAL CRAFT

CH : 16

URGENCY

CALL TYPE : NEUTRAL

6. URGENCY is selected; press the ENT key.

7. Choose SAFETY, or URGENCY as appropriate followed by pressing the ENT

key.

8. Press the CALL key more than three seconds to transmit the call. After the

call is transmitted, the standby display appears.

3.8.2 Receiving a neutral craft call

1. When a neutral craft call is received, the alarm sounds and the display

changes as below.

Neutral craft

call received.

FROM : 123456789

SAFETY

TCmd1 : SIMPLEX TP

TCmd2 : NEUTRAL CRAFT

CH : 16

CANCEL ALARM

3. DSC OPERATION FOR NON-DISTRESS CASES

3-30

2. Press the CANCEL or ENT key. The audible alarm is silenced and the display

changes as below.

** Received Message **

APR01/04 12 : 34 ECC : OK

NEUTRAL CALL

APR01/04 12 : 34 ECC : OK

SAFETY

TCmd1 : SIMPLEX TP

TCmd2 : NEUTRAL CRAFT

CH : 16

FROM : 123456789

PRESS ENT TO CHANGE CH

3. Press the ENT key. The display changes to the standby display, indicating

CH16.

3.9 Medical Transport Call

The medical transport call informs all ships, by urgency priority, that own ship

carries medical supplies.

3.9.1 Sending a medical transport call

1. Press the CALL key. The display changes from the standby display to the

COMPOSE MESSAGE screen and the CALL TYPE is displayed in reverse

video.

2. Press the ENT key to open the call type list.

3. Rotate the CH knob (or press up / down arrow key) to choose the MEDICAL

and press the ENT key.

4. Press the CALL key to transmit the call. After the call is transmitted, the

standby display appears, with CH16 selected.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-31

3.9.2 Receiving a medical transport call

1. When a medical call is received, the alarm sounds and the display changes as

below.

Medical call

received.

FROM : 123456789

URGENCY

TCmd1 : SIMPLEX TP

TCmd2 : MEDICAL

CH : 16

CANCEL ALARM

2. Press the CANCEL or ENT key. The audible alarm stops and the display

changes as below.

** Received Message **

APR01/04 12 : 34 ECC : OK

MEDICAL CALL

URGENCY

TCmd1 : SIMPLEX TP

TCmd2 : MEDICAL

CH : 16

FROM : 123456789

PRESS ENT

3. Press the ENT key. The display changes to the standby display, indicating

CH16.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-32

3.10 Log File

Three log files are provided for storage of calls: received ordinary log, received

distress log and transmitted log. Each log file stores 50 calls, on a first-in,

first-out basis. This means that the latest call is saved as log no.1 and the log no.

of all previous calls in that log increments by one. When the storage capacity is

exceeded, the oldest call is deleted to make room for the latest. An asterisk (*)

marks unread or unacknowledged calls. Received distress calls are

automatically deleted 48 hours after being read.

3.10.1 Opening a log file

The procedure for opening a log is common to all logs.

1. Press the LOG key to open the SELECT LOG FILE display.

2. Rotate the CH knob to choose RCVD ORDINARY, RCVD DISTRESS or

TRANSMITTED as appropriate and press the ENT key. For example, choose

RCVD ORDINARY or TRANSMITTED.

01: APR 10/04 12:30

RCVD ORDINARY LOG 1/13

INDIVIDUAL SHIP BQ

02: APR 15/04 10: 15

ALL SHIP

03: APR 25/04 11: 30

COAST CALL RQ

TRANSMITTED 1/13

04: MAY10/04 18: 30

COAST CALL RQ

01: APR 10/04 12:35

INDIVIDUAL SHIP

02: APR 15/04 10: 25

ALL SHIP

03: APR 25/04 12: 30

COAST CALL

04: MAY10/04 19: 30

COAST CALL

3. Rotate the CH knob to choose a file you wish to browse.

The in the RCVD ORDINARY LOG indicates unread or unacknowledged

message.

4. If you wish to print the file selected, press the PRINT key.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-33

5. Press the ENT key to open the message. Below is a sample message.

** Received Message **

APR 10/’04 18:30 ECC : OK

INDIVIDUAL SHIP RQ

CH : 16

TCmd1 : SIMPLEX TP

TCmd2 : NO INFO

ROUTINE

FROM : 123456789

ANSWER

DELETE

For a received message

which requires a reply,

ANSWER is displayed

(for 4.5 minutes).

To reply choose it and

press the ENT key.

6. Press ▲ or ▼ key to open previous or next page on the log.

7. If you wish to delete the file selected at step 3, choose DELETE and press the

ENT key. The following confirmation window appears.

YES

DELETE

RECEIVED ORDINARY LOG

ARE YOU SURE?

8. Choose YES and press the ENT key.

3. DSC OPERATION FOR NON-DISTRESS CASES

3-34

This page is intentionally left blank.

4-1

4. BASIC SETUP

4.1 Alarm Setup

This section provides the procedures for setting up various alarms. The alarm

menu enables/disables internal and external alarms. Note that the

Distress/Urgency alarm cannot be disabled.

Disabling/enabling old position alarm in manual position entry mode

This alerts the operator when manually entered position data is older by the

number of hours or minutes set in the next Position Older field.

1. Press the MENU key.

**** SETUP MENU ****

ALARM

ERASE LOG

MEMORY CHANNEL

AUTO ACK

MESSAGE FILE ENTRY

* SETUP MENU *

ALARM

ERASE LOG

MEMORY CH

AUTO ACK

MESSAGE FILE

SETUP MENU on transceiver unit SETUP MENU on remote handset

2. ALARM is selected; press the ENT key to display the ALARM menu.

**** ALARM MENU ****

POSITION OLDER 4H

EXT ALARM DSTRS/URG

OLD POSITION OFF

* ALARM MENU *

OLD POSITION

OFF

POSITION OLDER

ALARM MENU on transceiver unit

ALARM MENU on remote handset

(You can get same information by

scrolling with up / down arrow

keys)

3. Rotate the CH knob (or press up / down arrow key) to choose OLD POSITION

from the ALARM MENU and press the ENT key. The setting window appears.

4. Rotate the CH knob (or press up / down arrow key) to choose ON or OFF as

appropriate and press the ENT key. If you chose ON, the message "Warning:

Update position" appears when manually entered position is older than the

time set on the ALARM MENU.

5. Press the CANCEL key twice to return to the standby display.

4. BASIC SETUP

4-2

To set "position older" alarm

1. Rotate the CH knob (or press up / down arrow key) to choose POSITION

OLDER (POS. OLDER for remote handset) from the ALARM MENU and

press the ENT key. The following setting window appears.

2. Rotate the CH knob (or press up / down arrow key) to choose an appropriate

value and press the ENT key.

Alarm is output when position is older by the number of hours set here.

3. Press the CANCEL key twice to return to the standby display.

To set type of alarm to output

1. Rotate the CH knob (or press up / down arrow key) to choose EXT ALARM

from the ALARM MENU and press the ENT key. The following setting window

appears.

DIST/URG : ON

SAFETY : OFF

ROUTINE : OFF

Always ON

2. Rotate the CH knob (or press up / down arrow key) to choose an appropriate.

Option. Alarm is output to external device.

DSTRS/URG: Distress or urgency call output upon receipt.

SAFETY: Safety call output upon receipt.

ROUTINE: Routine call output upon receipt.

3. Press the ENT key.

4. Press the CANCEL key twice to return to the standby display.

4. BASIC SETUP

4-3

4.2 Auto ACK Setup

The Auto Ack Menu enables/disables automatic acknowledgement of ship, coast,

position and polling calls.

Comply type

Set of [5 ACQ]

ABLE

UNABLE

AUTO ACK Can send acknowledge

automatically.

Can send UNABLE

automatically.

MANUAL ACK Can send acknowledge

manually

Can send UNABLE

manually.

To set COMPLY TYPE

1. Press the MENU key.

2. Rotate the CH knob (or press up / down arrow key) to choose AUTO ACK and

press the ENT key. The following menu appears.

**** AUTO ACK MENU ****

COMPLY STATUS ABLE

NO REASON

POSITION CALL ON

UNABLE REASON

POLLING CALL ON

3. COMPLY STATUS is selected; press the ENT key. The following setting

window appears.

ABLE

UNABLE

4. Rotate the CH knob (or press up / down arrow key) to choose ABLE or

UNABLE as automatic acknowledgement reply to each call.

5. Press the ENT key.

Note: Automatic acknowledge is automatically disabled when RX call

contains error, as required by law. Further, automatic acknowledge is

disabled in case of OFF HOOK.

4. BASIC SETUP

4-4

To set reason for unable

If you have chosen UNABLE as the COMPLY STATUS, set the reason as

follows:

1. Rotate the CH knob (or press up / down arrow key) to choose UNABLE

REASON from the AUTO ACK MENU and press the ENT key. The following

menu appears.

NO REASON

BUSY

EQUIP DISBLD

MODE UNAVAIL

CH UNAVAIL

2. Rotate the CH knob (or press up / down arrow key) to choose a reason for

UNABLE.

3. Press the ENT key.

Note: This menu is the same as manual acknowledgement. EQUIPMENT

DISABLE is shown in calls when EQUIP DISBLD is selected.

To set position call response

1. Rotate the CH knob (or press up / down arrow key) to choose the POSITION

CALL from the AUTO ACK MENU and press the ENT key.

2. Rotate the CH knob (or press up / down arrow key) to choose ON or OFF as

appropriate.

OFF: Disables automatic acknowledgement of position request.

ON: Enables automatic acknowledgement of position request.

3. Press the ENT key.

To set polling call response

1. Rotate the CH knob (or press up / down arrow key) to choose the POLLING

CALL from the AUTO ACK MENU and press the ENT key.

2. Rotate the CH knob (or press up / down arrow key) to choose ON or OFF as

appropriate.

OFF: Disables automatic acknowledgement of polling request.

ON: Enables automatic acknowledgement of polling request.

3. Press the ENT key.

4. BASIC SETUP

4-5

4.3 Erasing Logs

Erasing received ordinary log

1. Press the MENU key.

2. Rotate the CH knob (or press up / down arrow key) to choose the ERASE

LOG and press the ENT key. The following window appears.

RCVD ORDINARY

RCVD DISTRESS

TRANSMITTED

*** ERASE LOG MENU ***

3. RCVD ORDINARY is selected; press the ENT key to erase the received

ordinary log.

Erasing received distress log

1. Press the MENU key.

2. Rotate the CH knob (or press up / down arrow key) to choose ERASE LOG

and press the ENT key.

3. Rotate the CH knob (or press up / down arrow key) to choose RCVD

DISTRESS and press the ENT key to erase the received distress log.

Erasing transmitted log

1. Press the MENU key.

2. Rotate the CH knob (or press up / down arrow key) to choose ERASE LOG

and press the ENT key.

3. Rotate the CH knob (or press up / down arrow key) to choose TRANSMITTED

and press the ENT key.

YES

ERASE

TRANSMITTED

ARE YOU SURE?

4. Choose YES and press the ENT key to erase the transmitted message log.

4. BASIC SETUP

4-6

4.4 Memory Channel Setup

You can save up to 50 channels as follows.

1. Press the MENU key.

2. Rotate the CH knob (or press up / down arrow key) to choose MEMORY

CHANNEL and press the ENT key.

* Memory Channel 1/7*

01 CH-- --------

02 : CH-- --------

03 : CH-- --------

04 : CH-- --------

05 : CH-- --------

06 : CH-- --------

07 : CH-- --------

08 : CH-- --------

3. Rotate the CH knob (or press up / down arrow key) to choose a vacant CH

number and press the ENT key.

INTL

USA

CANADA

INLND-WA

PRIV

ERASE

* : Only permitted channel

modes are displayed,

which are set by the

installer of the equipment.

4. Rotate the CH knob (or press up / down arrow key) to choose appropriate

channel type and press the ENT key.

5. Rotate the CH knob (or press up / down arrow key) to choose channel number

and press the ENT key.

4. BASIC SETUP

4-7

4.5 Message File Entry

In this section you will learn how to prepare and store ship, coast, PSTN, group,

and area calls for future transmission. 100 calls can be stored.

1. At the standby display, press the MENU key to open the SETUP MENU.

**** SETUP MENU ****

ALARM

ERASE LOG

MEMORY CHANNEL

AUTO ACK

MESSAGE FILE ENTRY

2. Rotate the CH knob (or press up / down arrow key) to choose MESSAGE

FILE ENTRY and press the ENT key.

* MESSAGE FILE 1/13 *

3. Rotate the CH knob to choose a vacant number and press the ENT key. The

following selection window appears.

COAST CALL

SHIP CALL

PSTN CALL

GROUP CALL

AREA CALL

4. BASIC SETUP

4-8

4. Rotate the CH knob to choose the call type and press the ENT key. One of the

following display appears depending on the call type selected above.

Note1: The communication priority is ROUTINE only.

Note2: The group ID will be registered automatically after a group call

message file is saved.

4. BASIC SETUP

4-9

5. Press the ENT key and key in each ID or AREA followed by the ENT key.

To enter area

1: N/E 2: S/W

°---

-- ↓→

N°E°

-- °

a) Enter latitude (degrees) and 1 for north or 2 for south of reference point.

b) Enter longitude (degrees) and 1 for east or 2 for west.

c) Enter southerly degrees of area.

d) Enter easterly degrees of area.

e) Press the ENT key.

6. TCmd1 is selected; press the ENT key.

7. Choose SIMPLEX TP, DUPLEX TP, DATA or FAX as appropriate followed by

pressing the ENT key. If you chose SIMPLEX, DUPLEX, or FAX, NO INFO

appears in the Tcmd2 field. Go to step 10. If you chose DATA, go to the next

step.

8. Tcmd2 is selected; press the ENT key.

V. 26 ter

V. 27 ter

V. 32

V. 21

V. 22

V. 22 bis

V. 23

V. 26 bis

9. Choose an appropriate data type and press the ENT key.

10. Choose CH and press the ENT key. The following window appears.

SELECT CH

NO INFO

11. Choose SELECT CH with the CH knob (or up / down arrow key) and press

the ENT key.

SIMP CHANNEL

In case of NO INFO, there is no channel information.

4. BASIC SETUP

4-10

12. Choose a channel with the CH knob (or up / down arrow key) and press the

ENT key.

13. Press the ENT key to open the name entry window.

14. Enter a name with the alphanumeric keys. To change a digit, rotate the CH

knob. Press the ENT key.

15. REGIST is selected; press the ENT key to register. To erase, rotate the CH

knob to select ERASE and press the ENT key.

Note: To send a message, after pressing the CALL key, choose CALL TYPE,

highlighting xxx ID, press the FILE key to show the name list. Choose

a name from the list.

To send a message file:

1) Press the CALL key.

2) Choose call type and press the ENT key.

3) Highlighting xxx ID, press the FILE key to display list of message files.

4) Choose file to send and press the ENT key..

5) Press the CALL key more than three seconds.

4. BASIC SETUP

4-11

4.6 Position Setup

This is where you enter your position, automatically or manually.

1. Press the MENU key at the standby display.

2. Rotate the CH knob (or press up / down arrow key) to choose POSITION from

the second page of the main menu.

**** SETUP MENU ****

POSITION

VOLUME

PRINT OUT

SYSTEM

3. Press the ENT key. The following menu appears.

INPUT TYPE: AUTO

LAT : -- °--’-

LON : ---°--’-

TIME : -- : --

4. INPUT TYPE is selected; press the ENT key. The following setting window

appears.

AUTO

MANUAL

5. Rotate the CH knob (or press up / down arrow key) to choose AUTO or

MANUAL as appropriate and press the ENT key.

If you chose AUTO, your ship's position and time appear; press the CANCEL

to close the menu and return to the standby display. These data are supplied

from the navigation equipment connected.

Note: • If the position data from a positioning sensor is available, MANUAL

can not be chosen.

• If correct position data is entered from a position source in the

setting of MANUAL, the setting changes automatically to AUTO from

MANUAL.

• If the message "No Position Data" appears after you change INPUT

TYPE from MANUAL to AUTO, confirm that the navigation device is

functioning.

If you chose MANUAL, enter your position and time as follows.

6. Enter latitude (in four digits) with the numeric keys. If necessary, switch

coordinates: 1 key to switch to North; 2 key to switch to South.

7. Press the ENT key and enter longitude (in five digits) with the numeric keys. If

necessary, switch coordinates: 1 key to switch to East; 2 key to switch to

West.

8. Press the ENT key and enter UTC time with the numeric keys.

9. Press the ENT key and CANCEL key to finish.

4. BASIC SETUP

4-12

4.7 Print Out Setup

The PRINT MENU enables/disables automatic printing of all transmitted and

received calls and the results of the daily test.

1. Press the MENU key at the standby display to open menu.

2. Rotate the CH knob (or press up / down arrow key) to choose PRINT OUT

from the second page of the main menu and press the ENT key.

**** PRINT MENU ****

XMTD CALL MANUAL

DAILY TEST MANUAL

RCVD CALL MANUAL

3. Choose appropriate item among XMTD CALL MANUAL, RCVD CALL

MANUAL or DAILY TEST MANUAL and press the ENT key.

MANUAL

AUTO

4. Choose AUTO or MANUAL as appropriate and press the ENT key.

5. Press the CANCEL to return to the standby display.

Sample printouts

Printing can be done automatically or manually. For manual printing, press the

6 PRINT key.

** Transmitted Message **

SEP25/ ’04 17:41

SHIP ACK

TO: 111111111

ROUTINE

TCmd1: SIMPLEX TP

TCmd2: NO INFO

CH: 12

** Received Message **

SEP25/ ’04 17:40 ECC: OK

SHIP CALL

FROM: 111111111

ROUTINE

TCmd1: SIMPLEX TP

TCmd2: NO INFO

CH: 12

* Daily test result *

SEP25/ ’04 17:42

MMSI: 987654321

TX POWER: OK

TX/RX PCB: OK

CPU PCB: OK

CH70RX PCB: OK

DUP RX PCB: OK

Sample printout

4. BASIC SETUP

4-13

4.8 Volume Setup

The VOLUME menu enables/disables key beep (acknowledges correct key

input) and adjusts the volume of the earpiece, intercom and off-hook

loudspeaker.

1. Press the MENU key at the standby display.

2. Rotate the CH knob (or press up / down arrow key) to choose VOLUME and

press the ENT key.

**** VOLUME MENU ****

KEY CLICK 8

INTERCOM VOLUME 8

EARPIECE LEVEL 9

OFF HOOK SPKR ON

Follow the appropriate procedure to adjust volume of desired item.

Key click

1. Choose KEY CLICK, and press the ENT key.

KEY CLICK LEVEL SETUP

EXT: ENT

LEVEL (0-16)

KEY CLICK

LEVEL SETUP

EXT: ENT

LEVEL (0-16)

Note: Do not confuse keyboard beep (single beep) with ACK beep (three

beeps).

2. Rotate the CH knob (or press up / down arrow key) to set the key click level.

The setting range is 0 to 16.

3. Press the ENT key.

Earpiece volume

1. Choose ERAPIECE LEVEL and press the ENT key.

EARPIECE LEVEL SETUP

EXT: ENT

LEVEL (8-16)

EARPIECE

LEVEL SETUP

EXT: ENT

LEVEL (1-4)

Transceiver unit Remote handset

2. Rotate the CH knob (or press up / down arrow key) to set the earpiece volume

level. The setting range is 8 to 16 for transceiver handset.

3. Press the ENT key.

4. BASIC SETUP

4-14

Intercom volume

1. Choose INTERCOM VOLUME and press the ENT key.

INTERCOM SETUP

EXT: ENT

LEVEL (1-16)

2. Rotate the CH knob (or press up / down arrow key) to set the intercom volume

level. The setting range is 1 to 16.

3. Press the ENT key.

Off-hook loudspeaker

1. Choose OFFHOOK SPKR and press the ENT key.

2. Choose ON or OFF and press the ENT key.

5-1

5. SYSTEM SETUP

5.1 Displaying Self ID

1. Press the MENU key.

**** SETUP MENU ****

ALARM

ERASE LOG

MEMORY CHANNEL

AUTO ACK

MESSAGE FILE ENTRY

**** SETUP MENU ****

VOLUME

TEST

PRINT OUT

SYSTEM

POSITION

2. Rotate the CH knob (or press up / down arrow key) to choose SYSTEM from

page 2 of the menu and press the ENT key. The following window appears.

The self ID is displayed on the first line.

* SYSTEM SETUP MENU *

SELF ID 123498765

GROUP ID LIST

INTERCOM NAMING

PROGRAM VERSION

* SYSTEM

SETUP MENU *

SELF ID

123498765

GROUP ID LIST

Transceiver unit Remote handset

5.2 Displaying Group ID LIST

1. Press the MENU key.

2. Rotate the CH knob (or press up / down arrow key) to choose SYSTEM from

page 2 of the menu and press the ENT key.

3. Rotate the CH knob (or press up / down arrow key) to choose GROUP ID

LIST and press the ENT key to show the GROUP ID list. For how to registers

group IDs, see paragraph 4.5.

5. SYSTEM SETUP

5-2

5.3 Naming Intercom

1. Press the MENU key.

**** SETUP MENU ****

ALARM

ERASE LOG

MEMORY CHANNEL

AUTO ACK

MESSAGE FILE ENTRY

**** SETUP MENU ****

VOLUME

TEST

PRINT OUT

SYSTEM

POSITION

2. Rotate the CH knob (or press up / down arrow key) to choose SYSTEM from

page 2 of the menu and press the ENT key. The following window appears.

* SYSTEM SETUP MENU *

SELF ID ---------------------

GROUP ID LIST

INTERCOM NAMING

PROGRAM VERSION

3. Rotate the CH knob (or press up / down arrow key) to choose INTERCOM

NAMING and press the ENT key. The following window appears.

* Intercom Naming Menu *

1 : Handset 1

2 : Handset 2

3 : Handset 3

4 : Handset 4

RT : FM8800D

4. Rotate the CH knob (or press up / down arrow key) to choose a handset

number and press the ENT key.

5. Key in remote station name with alphanumeric keys and press the ENT key.

6. Repeat steps 4 and 5 to name other handsets.

5. SYSTEM SETUP

5-3

5.4 Displaying Program Version

1. Press the MENU key.

****SETUPMENU****

ALARM

ERASELOG

MEMORYCHANNEL

AUTOACK

MESSAGEFILEENTRY

****SETUPMENU****

VOLUME

TEST

PRINTOUT

SYSTEM

POSITION

2. Rotate the CH knob to choose SYSTEM and press the ENT key. The following

selection window appears.

3. Rotate the CH knob to choose PROGRAM VERSION and press the ENT key

to show program version number.

Programversion

FM8800S

0550215-02

EXT:ENT

Program version

orFM8800D

4. Press the ENT key to exit.

5. SYSTEM SETUP

5-4

This page is intentionally left blank.

6-1

6. MAINTENANCE &

TROUBLESHOOTING

Do not open the equipment.

Hazardous voltage which can

cause electrical shock, burn or

serious injury exists inside the

equipment. Do not work inside

the equipment unless familiar

with electrical circuits.

WARNINGWARNING

6.1 Maintenance

Periodic checks

1) Check that each connector is firmly connected.

2) Clean corroded or soiled connectors.

3) Check coaxial cable for damage. If damaged, replace.

4) Check that bolts fixing the antenna are firmly tightened.

6.2 Troubleshooting

When the power cannot be turned on

1) Check if power plug is firmly connected.

2) Check fuses in the power cable. If it has tripped, replace it with a new one

(15A).

3) If power cannot be turned on (after checking 1 and 2), contact a FURUNO

agent or representative for advice.

6. MAINTENANCE & TROUBLESHOOTING

6-2

6.3 Daily Test

Authorities require that the DSC be checked daily for proper operation to ensure

that it will function properly in the event of distress. Execute the daily test as

below.

1. At the standby display, press the SHIFT key and TEST key in that order. The

following display appears for test.

*** DAILY TEST ***

TX POWER : OK

TX/RX PCB : OK

CPU PCB : OK

CH70 RX PCB : OK

DUP RX PCB : OK

Test in progress (Pop-up display appears momentarily.)

If you have not pressed the PTT switch

before executing the test, "NO CHECK"

is displayed.

FM-8800D only

Result of daily test

2. To stop the daily test, press the CANCEL key.

If there is any problem, “NG” appears instead of “OK” for offending item. For any NG,

contact a FURUNO agent or representative for advice.

The table below shows the abnormal indications and causes shown in the daily test.

Indication Cause

TX POWER: NG Indicates no transmitting output power.

PA module or TX/RX pcb 05P0774 may be damaged.

TX/RX PCB: NG Indicates abnormal PLL circuit in the TX/RX pcb.

TX/RX pcb 05P0774 may be damaged.

CPU PCB: NG Indicates abnormal loop circuit inside the CPU board.

CPU pcb 05P0773 may be damaged.

CH70 RX PCB: NG Indicates abnormal loop circuit between CPU and CH70

RX pcb. CH70 RX pcb 05P0775 may be damaged.

DUP RX PCB: NG Indicates abnormal PLL circuit in the DUP RX pcb.

DUP RX pcb 05P0777 may be damaged.

If necessary, refer to Parts Location on subsequent pages.

executing

6. MAINTENANCE & TROUBLESHOOTING

6-3

6.4 Error Message

The table below shows all the error messages which may appear.

Error message Meaning

PLL1 Unlock PLL circuit on the TX/RX pcb 05P0774 has unlocked.

PLL2 Unlock PLL circuit on the DUP RX pcb 05P0777 has unlocked (only

FM-8800D).

ANT ERROR The antenna is abnormal. In this condition, if the

transmission continues more than five seconds, the output

power is reduced to approximately 10W.

GPS ERROR There is no L/L input from a positioning sensor for more than

one minute.

System Error The DSP (digital signal processor) is abnormally.

Note: If the CPU is abnormal, the beep sounds continuously until turning off the

power.

6.5 Parts Location

Transceiver unit FM-8800D/8800S

DUPLEXER

PWR pcb

05P0776

TX/RX pcb

05P0774

Top cover removed

PANEL pcb

05P0772

DUP RX pcb

05P0777

CH70 RX pcb

05P0775 CPU pcb

05P0773

Bottom cover removed

6. MAINTENANCE & TROUBLESHOOTING

6-4

Bottom cover removed

Handset HS-2003

HANDSET pcb

05P0780

Remote station RB-8800/RB-8810

TB pcb

07P0782 05P0779

REMOTE pcb TB pcb

05P0798 HS CONT pcb

05P0781

Junction box

JUNCTION pcb

05P0790

DMC Interface

DMC IF pcb

05P0778

P-1

APPENDIX

Menu Tree

[MENU] ALARM

UNABLE REASON

ABLE/UNABLE

AUTO ACK COMPLY STATUS

POSITION CALL

NO REASON/BUSY/EQUIP DISBLD/

MODE UNAVAIL/CH UNAVAIL

EXT ALARM

4H/3H/2H/1H/0.5H

OLD POSITION

POSITION OLDER

DIST/URG, ON

ON/OFF

POLLING CALL ON/OFF

ERASE LOG RCVD ORDINARY

RCVD DISTRESS

TRANSMITTED

MEMORY CHANNEL 50 entries

MESSAGE FILE ENTRY 100 entries

POSITION AUTO/MANUAL LAT/LONG/TIME

PRINT OUT XMTD CALL

RCVD CALL

DAILY TEST

AUTO/MANUAL

VOLUME

OFFHOOK SPKR

KEY CLICK

EARPIECE LEVEL

INTERCOM VOLUME

ON/OFF

8 (0-16)

9, 8 - 16 (For remote handset, 1-4)

8, 1 - 16

SYSTEM

PROGRAM VERSION

SELF ID

GROUP ID LIST

INTERCOM NAMING

Bold: Default

SAFETY ON/OFF

ROUTINE ON/OFF

[LOG] RCVD ORDINARY (50LOG)

RCVD DISTRESS (50LOG)

TRANSMITTED (50LOG)

APPENDIX

AP-2

[CALL] COAST CALL COAST ID

ROUTINE

GROUP CALL GROUP ID

PSTN CALL COAST ID

ALL SHIPS

BUSINESS

SHIP CALL SHIP ID

SAFETY

URGENCY

SAFETY

URGENCY

DISTRESS

TCmd1 SIMPLEX TP

DUPLEX TP

DATA

FAX

TCmd2

CH NO INFO

SELECT CH

ROUTINE

BUSINESS

SAFETY

URGENCY

DISTRESS

TCmd1 SIMPLEX TP

DUPLEX TP

DATA

FAX

TCmd2

CH NO INFO

SELECT CH

ROUTINE

BUSINESS

SAFETY

URGENCY

DISTRESS

TCmd1 SIMPLEX TP

DUPLEX TP

DATA

FAX

TCmd2

CH NO INFO

SELECT CH

TCmd1 SIMPLEX TP

DUPLEX TP

TCmd2: NO INFO

TEL

DISTRESS

TCmd1 SIMPLEX TP

DUPLEX TP

DATA

FAX

TCmd2: NO INFO

CH NO INFO

SELECT CH SIMP CHANNEL

DUP CHANNEL

AREA CALL ARE -- ---- - -- --

°°°°

→

↓

ROUTINE

BUSINESS

SAFETY

URGENCY

DISTRESS

TCmd1 SIMPLEX TP

DUPLEX TP

DATA

FAX

TCmd2

CH NO INFO

SELECT CH

POSITION SHIP ID

ROUTINE

BUSINESS

SAFETY

URGENCY

DISTRESS

TCmd1: POSITION REQUEST

TCmd2: NO INFO

ROUTINE

COAST ID:

BUSINESS

SHIP ID

SAFETY

URGENCY

UNDESIGNATED

Fire

Flooding

Collision

Grounding

Listing

Sinking

Disabled & Adr

Abandoning

POS:

AT:

SIMP TP

AUTO

POLLING

DISTRESS

NEUTRAL URGENCY

SAFETY

CH: 16

MEDICAL URGENCY

TCmd1: SIMPLEX TP

CH: 16

TCmd2: MEDICAL TRSPRT

RELAY ALL ID IN DIST

TCmd: DISTRESS RELAY

NATURE

Piracy

Man over board

EPIRB

MANUAL

NO INFO

DISTRESS

RELAY SEL

UNDESIGNATED

Fire

Flooding

Collision

Grounding

Listing

Sinking

Disabled & Adr

Abandoning

POS:

AT:

SIMP TP

AUTO

ID IN DIST:

TCmd: DISTRESS RELAY

NATURE

Piracy

Man over board

EPIRB

MANUAL

NO INFO

UNDESIGNATED

Fire

Flooding

Collision

Grounding

Listing

Sinking

Disabled & Adr

Abandoning

POS:

AT:

SIMP TP

AUTO

NATURE

Piracy

Man over board

EPIRB

MANUAL

NO INFO

APPENDIX

P-3

Marine VHF Channel Lists

1) International Channels

MHz

MHz Remark CH

MHz

MHz Remark

01 156.050 160.650 60 156.025 160.625

02 156.100 160.700 61 156.075 160.675

03 156.150 160.750 62 156.125 160.725

04 156.200 160.800 63 156.175 160.775

05 156.250 160.850 64 156.225 160.825

06 156.300 156.300 65 156.275 160.875

07 156.350 160.950 66 156.325 160.925

08 156.400 156.400 67 156.375 156.375

09 156.450 156.450 68 156.425 156.425

10 156.500 156.500 69 156.475 156.475

11 156.550 156.550 70 - 156.525 DSC

12 156.600 156.600 71 156.575 156.575

13 156.650 156.650 72 156.625 156.625

14 156.700 156.700 73 156.675 156.675

15 156.750 156.750

Low

PWR 74 156.725 156.725

16 156.800 156.800 75 156.775 156.775

Low

PWR

17 156.850 156.850

Low

PWR 76 156.825 156.825

Low

PWR

18 156.900 161.500 77 156.875 156.875

19 156.950 161.550 78 156.925 161.525

20 157.000 161.600 79 156.975 161.575

21 157.050 161.650 80 157.025 161.625

22 157.100 161.700 81 157.075 161.675

23 157.150 161.750 82 157.125 161.725

24 157.200 161.800 83 157.175 161.775

25 157.250 161.850 84 157.225 161.825

26 157.300 161.900 85 157.275 161.875

27 157.350 161.950 86 157.325 161.925

28 157.400 162.000 87 157.375 157.375

88 157.425 157.425

APPENDIX

AP-4

2) USA Channels

MHz

MHz Remark CH

MHz

MHz Remark

01 156.050 156.050 60 - -

02 - - 61 - -

03 - - 62 - -

04 - - 63 156.175 156.175

05 156.250 156.250 64 - -

06 156.300 156.300 65 156.275 156.275

07 156.350 156.350 66 156.325 156.325

08 156.400 156.400 67 156.375 156.375

Low

PWR

09 156.450 156.450 68 156.425 156.425

10 156.500 156.500 69 156.475 156.475

11 156.550 156.550 70 - 156.525 DSC

12 156.600 156.600 71 156.575 156.575

13 156.650 156.650

Low

PWR 72 156.625 156.625

14 156.700 156.700 73 156.675 156.675

15 - 156.750 74 156.725 156.725

16 156.800 156.800 75 - -

17 156.850 156.850

Low

PWR 76 - -

18 156.900 156.900 77 156.875 156.875

Low

PWR

19 156.950 156.950 78 156.925 156.925

20 157.000 157.000 79 156.975 156.975

21 157.050 157.050 80 157.025 157.025

22 157.100 157.100 81 157.075 157.075

23 157.150 157.150 82 157.125 157.125

24 157.200 161.800 83 157.175 157.175

25 157.250 161.850 84 157.225 161.825

26 157.300 161.900 85 157.275 161.875

27 157.350 161.950 86 157.325 161.925

28 157.400 162.000 87 157.375 157.375

88 157.425 157.425

US Weather Channels

WX RX MHz WX RX MHz

01 162.550 06 162.500

02 162.400 07 162.525

03 162.475 08 161.650

04 162.425 09 161.775

05 162.450 10 163.275

APPENDIX

P-5

3) Canadian Channels

MHz

MHz Remark CH

MHz

MHz Remark

01 156.050 160.650 60 156.025 160.625

02 156.100 160.700 61 156.075 156.075

03 156.150 160.750 62 156.125 156.125

04 156.200 156.200 63

05 156.250 156.250 64 156.225 156.225

06 156.300 156.300 65 156.275 156.275

Low

PWR

07 156.350 156.350 66 156.325 156.325

08 156.400 156.400 67 156.375 156.375

09 156.450 156.450 68 156.425 156.425

10 156.500 156.500 69 156.475 156.475

11 156.550 156.550 70 - 156.525 DSC

12 156.600 156.600 71 156.575 156.575

13 156.650 156.650 72 156.625 156.625

14 156.700 156.700 73 156.675 156.675

15 156.750 156.750

Low

PWR 74 156.725 156.725

16 156.800 156.800 75 - -

17 156.850 156.850

Low

PWR 76 - -

18 156.900 156.900 77 156.875 156.875

Low

PWR

19 156.950 156.950 78 156.925 156.925

20 157.000 161.600

Low

PWR 79 156.975 156.975

21 157.050 157.050 80 157.025 157.025

22 157.100 157.100 81 157.075 157.075

23 157.150 161.750 82 157.125 157.125

24 157.200 161.800 83 157.175 157.175

25 157.250 161.850 84 157.225 161.825

26 157.300 161.900 85 157.275 161.875

27 157.350 161.950 86 157.325 161.925

28 157.400 162.000 87 157.375 157.375

88 157.425 157.425

APPENDIX

AP-6

4) Inland waterways (INLND-WA) Channels

MHz

MHz Remark CH

MHz

MHz Remark

01 156.050 160.650 60 156.025 160.625

02 156.100 160.700 61 156.075 160.675

03 156.150 160.750 62 156.125 160.725

04 156.200 160.800 63 156.175 160.775

05 156.250 160.850 64 156.225 160.825

06 156.300 156.300

Low

PWR 65 156.275 160.875

07 156.350 160.950 66 156.325 160.925

08 156.400 156.400

Low

PWR 67 156.375 156.375

09 156.450 156.450 68 156.425 156.425

10 156.500 156.500

Low

PWR 69 156.475 156.475

11 156.550 156.550

Low

PWR 70 - 156.525 DSC

12 156.600 156.600

Low

PWR 71 156.575 156.575

Low

PWR

13 156.650 156.650

Low

PWR 72 156.625 156.625

Low

PWR

14 156.700 156.700

Low

PWR 73 156.675 156.675

15 156.750 156.750

Low

PWR 74 156.725 156.725

Low

PWR

16 156.800 156.800 75 - -

17 156.850 156.850

Low

PWR 76 - -

18 156.900 161.500 77 156.875 156.875

Low

PWR

19 156.950 161.550 78 156.925 161.525

20 157.000 161.600 79 156.975 161.575

21 157.050 161.650 80 157.025 161.625

22 157.100 161.700 81 157.075 161.675

23 157.150 161.750 82 157.125 161.725

24 157.200 161.800 83 157.175 161.775

25 157.250 161.850 84 157.225 161.825

26 157.300 161.900 85 157.275 161.875

27 157.350 161.950 86 157.325 161.925

28 157.400 162.000 87 157.375 157.375

88 157.425 157.425

APPENDIX

P-7

5) Private Channels Note: Bold for FM-8800D duplex TX frequencies

TX RX

FM-8800S FM-8800D FM-8800S FM-8800D

Simplex Sim/Dup Simplex Semi-dup Simplex Duplex

CH NO（current） Remark

155.000 155.000 159.600 180

155.025 155.025 159.625 181

155.050 155.050 159.650 182

155.075 155.075 159.675 183

155.100 155.100 159.700 184

155.125 155.125 159.725 185

155.150 155.150 159.750 186

155.175 155.175 159.775 187

155.200 155.200 159.800 188

155.225 155.225 159.825 189

155.250 155.250 159.850 190

155.275 155.275 159.875 191

155.300 155.300 159.900 192

155.325 155.325 159.925 193

155.350 155.350 159.950 194

155.375 155.375 159.975 195

155.400 155.400 155.400 160.000 155.400 196

155.425 155.425 155.425 160.025 155.425 197

155.450 155.450 155.450 160.050 155.450 198

155.475 155.475 155.475 160.075 155.475 199

155.500 155.500 155.500 160.100 155.500 120(L1)

155.525 155.525 155.525 160.125 155.525 121(L2)

155.550 155.550 155.550 160.150 155.550 122

155.575 155.575 155.575 160.175 155.575 123

155.600 155.600 155.600 160.200 155.600 124

155.625 155.625 155.625 160.225 155.625 125(F1)(P1)

155.650 155.650 155.650 160.250 155.650 126(L3)

155.675 155.675 155.675 160.275 155.675 127

155.700 155.700 155.700 160.300 155.700 128

155.725 155.725 155.725 160.325 155.725 129

155.750 155.750 155.750 160.350 155.750 130

155.775 155.775 155.775 160.375 155.775 131(F2)(P2)

155.800 155.800 155.800 160.400 155.800 132

155.825 155.825 155.825 160.425 155.825 133(F3)(P3)

155.850 155.850 155.850 160.450 155.850 134

155.875 155.875 155.875 160.475 155.875 135

155.900 155.900 155.900 160.500 155.900 136

155.925 155.925 155.925 160.525 155.925 137

155.950 155.950 155.950 160.550 155.950 138

- Continued -

APPENDIX

AP-8

TX RX

FM-8800S FM-8800D FM-8800S FM-8800D

Simplex Sim/Dup Simplex Semi-dup Simplex Duplex

CH NO（current） Remark

155.975 155.975 155.975 160.575 155.975 139

156.000 156.000 156.000 160.600 156.000 160.600 00 Min DUPch

156.025 156.025 156.025 160.625 156.025 160.625 60

156.050 156.050 156.050 160.650 156.050 160.650 01

156.075 156.075 156.075 160.675 156.075 160.675 61

156.100 156.100 156.100 160.700 156.100 160.700 02

156.125 156.125 156.125 160.725 156.125 160.725 62

156.150 156.150 156.150 160.750 156.150 160.750 03

156.175 156.175 156.175 160.775 156.175 160.775 63

156.200 156.200 156.200 160.800 156.200 160.800 04

156.225 156.225 156.225 160.825 156.225 160.825 64

156.250 156.250 156.250 160.850 156.250 160.850 05

156.275 156.275 156.275 160.875 156.275 160.875 65

156.300 156.300 156.300 160.900 156.300 160.900 06

156.325 156.325 156.325 160.925 156.325 160.925 66

156.350 156.350 156.350 160.950 156.350 160.950 07

156.375 156.375 156.375 160.975 156.375 160.975 67

156.400 156.400 156.400 161.000 156.400 161.000 08

156.425 156.425 156.425 161.025 156.425 161.025 68

156.450 156.450 156.450 161.050 156.450 161.050 09

156.475 156.475 156.475 161.075 156.475 161.075 69

156.500 156.500 156.500 161.100 156.500 161.100 10

156.525 156.525 156.525 161.125 156.525 161.125 70

156.550 156.550 156.550 161.150 156.550 161.150 11

156.575 156.575 156.575 161.175 156.575 161.175 71

156.600 156.600 156.600 161.200 156.600 161.200 12

156.625 156.625 156.625 161.225 156.625 161.225 72

156.650 156.650 156.650 161.250 156.650 161.250 13

156.675 156.675 156.675 161.275 156.675 161.275 73

156.700 156.700 156.700 161.300 156.700 161.300 14

156.725 156.725 156.725 161.325 156.725 161.325 74

156.750 156.750 156.750 161.350 156.750 161.350 15

156.775 156.775 156.775 161.375 156.775 161.375 75

156.800 156.800 156.800 161.400 156.800 161.400 16

156.825 156.825 156.825 161.425 156.825 161.425 76

156.850 156.850 156.850 161.450 156.850 161.450 17

156.875 156.875 156.875 161.475 156.875 161.475 77

156.900 156.900 156.900 161.500 156.900 161.500 18

156.925 156.925 156.925 161.525 156.925 161.525 78

156.950 156.950 156.950 161.550 156.950 161.550 19

- Continued -

APPENDIX

P-9

TX RX

FM-8800S FM-8800D FM-8800S FM-8800D

Simplex Sim/Dup Simplex Semi-dup Simplex Duplex

CH NO（current） Remark

156.975 156.975 156.975 161.575 156.975 161.575 79

157.000 157.000 157.000 161.600 157.000 161.600 20

157.025 157.025 157.025 161.625 157.025 161.625 80

157.050 157.050 157.050 161.650 157.050 161.650 21

157.075 157.075 157.075 161.675 157.075 161.675 81

157.100 157.100 157.100 161.700 157.100 161.700 22

157.125 157.125 157.125 161.725 157.125 161.725 82

157.150 157.150 157.150 161.750 157.150 161.750 23

157.175 157.175 157.175 161.775 157.175 161.775 83

157.200 157.200 157.200 161.800 157.200 161.800 24

157.225 157.225 157.225 161.825 157.225 161.825 84

157.250 157.250 157.250 161.850 157.250 161.850 25

157.275 157.275 157.275 161.875 157.275 161.875 85

157.300 157.300 157.300 161.900 157.300 161.900 26

157.325 157.325 157.325 161.925 157.325 161.925 86

157.350 157.350 157.350 161.950 157.350 161.950 27

157.375 157.375 157.375 161.975 157.375 161.975 87

157.400 157.400 157.400 162.000 157.400 162.000 28

157.425 157.425 157.425 162.025 157.425 162.025 88

157.450 157.450 157.450 162.050 157.450 162.050 29

157.475 157.475 157.475 162.075 157.475 162.075 89

157.500 157.500 157.500 162.100 157.500 162.100 30 Max DUPch

157.525 157.525 157.525 162.125 157.525 90

157.550 157.550 157.550 162.150 157.550 31

157.575 157.575 157.575 162.175 157.575 91

157.600 157.600 157.600 162.200 157.600 32

157.625 157.625 157.625 162.225 157.625 92

157.650 157.650 157.650 162.250 157.650 33

157.675 157.675 157.675 162.275 157.675 93

157.700 157.700 157.700 162.300 157.700 34

157.725 157.725 157.725 162.325 157.725 94

157.750 157.750 157.750 162.350 157.750 35

157.775 157.775 157.775 162.375 157.775 95

157.800 157.800 157.800 162.400 157.800 36

157.825 157.825 157.825 162.425 157.825 96

157.850 157.850 157.850 162.450 157.850 37

157.875 157.875 157.875 162.475 157.875 97

157.900 157.900 157.900 162.500 157.900 38

157.925 157.925 157.925 162.525 157.925 98

157.950 157.950 157.950 162.550 157.950 39

- Continued -

APPENDIX

AP-10

TX RX

FM-8800S FM-8800D FM-8800S FM-8800D

Simplex Sim/Dup Simplex Semi-dup Simplex Duplex

CH NO（current） Remark

157.975 157.975 157.975 162.575 157.975 99

158.000 158.000 158.000 162.600 158.000 40

158.025 158.025 162.625 158.025 100

158.050 158.050 162.650 158.050 41

158.075 158.075 162.675 158.075 101

158.100 158.100 162.700 158.100 42

158.125 158.125 162.725 158.125 102

158.150 158.150 162.750 158.150 43

158.175 158.175 162.775 158.175 103

158.200 158.200 162.800 158.200 44

158.225 158.225 162.825 158.225 104

158.250 158.250 162.850 158.250 45

158.275 158.275 162.875 158.275 105

158.300 158.300 162.900 158.300 46

158.325 158.325 162.925 158.325 106

158.350 158.350 162.950 158.350 47

158.375 158.375 162.975 158.375 107

158.400 158.400 163.000 158.400 48

158.425 158.425 163.025 158.425 108

158.450 158.450 163.050 158.450 49

158.475 158.475 163.075 158.475 109

158.500 158.500 163.100 158.500 50

158.525 158.525 163.125 158.525 110

158.550 158.550 163.150 158.550 51

158.575 158.575 163.175 158.575 111

158.600 158.600 163.200 158.600 52

158.625 158.625 163.225 158.625 112

158.650 158.650 163.250 158.650 53

158.675 158.675 163.275 158.675 113

158.700 158.700 163.300 158.700 54

158.725 158.725 163.325 158.725 114

158.750 158.750 163.350 158.750 55

158.775 158.775 163.375 158.775 115

158.800 158.800 163.400 158.800 56

158.825 158.825 163.425 158.825 116

158.850 158.850 163.450 158.850 57

158.875 158.875 163.475 158.875 117

158.900 158.900 163.500 158.900 58

158.925 158.925 163.525 158.925 118

158.950 158.950 163.550 158.950 59

- Continued -

APPENDIX

P-11

TX RX

FM-8800S FM-8800D FM-8800S FM-8800D

Simplex Sim/Dup Simplex Semi-dup Simplex Duplex

CH NO（current） Remark

158.975 158.975 163.575 158.975 119

159.000 159.000 163.600 159.000 200 RX.max.freq

159.025 159.025 159.025 201

159.050 159.050 159.050 202

159.075 159.075 159.075 203

159.100 159.100 159.100 204

159.125 159.125 159.125 205

159.150 159.150 159.150 206

159.175 159.175 159.175 207

159.200 159.200 159.200 208

159.225 159.225 159.225 209

159.250 159.250 159.250 210

159.275 159.275 159.275 211

159.300 159.300 159.300 212

159.325 159.325 159.325 213

159.350 159.350 159.350 214

159.375 159.375 159.375 215

159.400 159.400 159.400 216

159.425 159.425 159.425 217

159.450 159.450 159.450 218

159.475 159.475 159.475 219

159.500 159.500 159.500 220

159.525 159.525 159.525 221

159.550 159.550 159.550 222

159.575 159.575 159.575 223

159.600 159.600 159.600 224

159.625 159.625 159.625 225

159.650 159.650 159.650 226

159.675 159.675 159.675 227

159.700 159.700 159.700 228

159.725 159.725 159.725 229

159.750 159.750 159.750 230

159.775 159.775 159.775 231

159.800 159.800 159.800 232

159.825 159.825 159.825 233

159.850 159.850 159.850 234

159.875 159.875 159.875 235

159.900 159.900 159.900 236

159.925 159.925 159.925 237

159.950 159.950 159.950 238

- Continued -

APPENDIX

AP-12

TX RX

FM-8800S FM-8800D FM-8800S FM-8800D

Simplex Sim/Dup Simplex Semi-dup Simplex Duplex

CH NO（current） Remark

159.975 159.975 159.975 239

160.000 160.000 160.000 240

160.025 160.025 160.025 241

160.050 160.050 160.050 242

160.075 160.075 160.075 243

160.100 160.100 160.100 244

160.125 160.125 160.125 245

160.150 160.150 160.150 246

160.175 160.175 160.175 247

160.200 160.200 160.200 248

160.225 160.225 160.225 249

160.250 160.250 160.250 250

160.275 160.275 160.275 251

160.300 160.300 160.300 252

160.325 160.325 160.325 253

160.350 160.350 160.350 254

160.375 160.375 160.375 255

160.400 160.400 160.400 256 Added ch no.

160.425 160.425 160.425 257 Added ch no.

160.450 160.450 160.450 258 Added ch no.

160.475 160.475 160.475 259 Added ch no.

160.500 160.500 160.500 140

160.525 160.525 160.525 141

160.550 160.550 160.550 142

160.575 160.575 160.575 143

160.600 160.600 160.600 144

160.625 160.625 160.625 145

160.650 160.650 160.650 146

160.675 160.675 160.675 147

160.700 160.700 160.700 148

160.725 160.725 160.725 149

160.750 160.750 160.750 150

160.775 160.775 160.775 151

160.800 160.800 160.800 152

160.825 160.825 160.825 153

160.850 160.850 160.850 154

160.875 160.875 160.875 155

160.900 160.900 160.900 156

160.925 160.925 160.925 157

160.950 160.950 160.950 158

- Continued -

APPENDIX

P-13

TX RX

FM-8800S FM-8800D FM-8800S FM-8800D

Simplex Sim/Dup Simplex Semi-dup Simplex Duplex

CH NO（current） Remark

160.975 160.975 160.975 159

161.000 161.000 161.000 160

161.025 161.025 161.025 161

161.050 161.050 161.050 162

161.075 161.075 161.075 163

161.100 161.100 161.100 164

161.125 161.125 161.125 165

161.150 161.150 161.150 166

161.175 161.175 161.175 167

161.200 161.200 161.200 168

161.225 161.225 161.225 169

161.250 161.250 161.250 170

161.275 161.275 161.275 171

161.300 161.300 161.300 172

161.325 161.325 161.325 173

161.350 161.350 161.350 174

161.375 161.375 161.375 175

161.400 161.400 161.400 176

161.425 161.425 161.425 177(M2)

161.450 161.450 161.450 178

161.475 161.475 161.475 179

APPENDIX

AP-14

Digital Interface (IEC 61162-1 Edition 2)

Input sentences

GGA, GLL, RMC, ZDA, GNS

Schematic diagram

05P0773

TXD-H

U15

1SS355

1000p

C65

TXD-C

RXD-H

RXD-C

100P

R70

R65

C64

100P

JP1

R69

120

220

R74 220

R73

1000p

C69 C70 CR3

PC400

Load requirements as listner

Isolation Optocoupler

Input impedance 560 ohms

Max. Voltage ±15V

Threshold 4 mA

Output sentence

TLL

APPENDIX

P-15

GGA - Global positioning system (GPS) fix data

APPENDIX

AP-16

GLL - Geographic position - latitude and longitude

GNS-GNSS fixed data

$--GNS,hhmmss.ss,llll.ll,a,yyyyy.yy,a,c--c,xx,x.x,x.x,x.x,x.x,x.x*hh<CR><LF>

| | | | | | | | | | | | |

| | | | | | | | | | | | +--- 11

| | | | | | | | | | | +------ 10

| | | | | | | | | | +---------- 9

| | | | | | | | | +-------------- 8

| | | | | | | | +------------------ 7

| | | | | | | +---------------------- 6

| | | | | | +------------------------- 5

| | | | | +------------------------------ 4

| | | +-------+--------------------------------- 3

| +--+--------------------------------------------- 2

+------------------------------------------------------------- 1

1. UTC of position

2. Latitude, N/S

3. Longitude, E/W

4. Mode indicator

5. Total number of satellites in use,00-99 (Not used.)

6. HDOP (Not used.)

7. Antenna altitude, meters, re: mean-sea-level(geoid) (Not used.)

8. Geoidal separation (Not used.)

9. Age of differential data (Not used.)

10. Differential reference station ID (Not used.)

11. Checksum

APPENDIX

P-17

RMC - Recommemded minimum specific GPS/TRANSIT data

1. UTC of position fix

2. Status: A=data valid, V=navigation receiver warming

3. Latitude, N/S

4. Longitude, E/W

5. Speed over ground, knots

6. Course over ground, degrees true

7. Date: dd/mm/yy

8. Magnetic variation, degree E/W

9. Mode indicator(see note)

10. Checksum

NOTE Positioning system Mode indicator:

A=Autonomous

D=Differential

E = Estimated (dead reckoning)

M = Manual input

S=Simulator

N=Data not valid

The Mode indicator field supplements the Status field. The Status field

shall be set to V=invalid for all values of Operating Mode except for

A=Autonomous and D=Differential. The positioning system Mode indicator

and Status field shall not be null fields.

$--RMC,hhmmss.ss,A,llll.lll,a,yyyyy.yyy,a,x.x,x.x,xxxxxx,x.x,a,a*hh<CR><LF>

| | | | | | | | | | | | |

| | | | | | | | | | | |

| | | | | | | | | | |

+------- 10

+--------- 9

+--+--------- 8

| | | | | | | | |

| | | | | | | |

+------------------ 7

| | | | | | | +---------------------- 6

+------------------------ 5

| | | | | |

+------------------------ 4+-----

| | | |

+----+--------------------------------- 3

| |

+-------------------------------------- 2

+-------------------------------------------- 1

ZDA - Time and data

APPENDIX

AP-18

TLL – Target latitude and longitude

$--TLL,xx,llll.lll,a,yyyyy.yyy,a,c--c,hhmmss.ss,a,a*hh<CR><LF>

| | | | | | | | | |

| | | | | | | | | +--------- 8

| | | | | | | | +----------- 7

| | | | | | | +------------- 6

| | | | | | +-------------------- 5

| | | | | +-------------------------- 4

| | | +-----+------------------------------ 3

| +----+------------------------------------------ 2

+----------------------------------------------------- 1

1. Target number 00 - 99

2. Latitude, N/S

3. Longitude, E/W

4. Target name

5. UTC of data

6. Target status(see note)

7. Reference target=R,null otherwise

8. Checksum

NOTE - Target status

L = lost, tracked target has beenlost

Q = query, target in the process of acquisition

T = tracking

Furuno USA 9ZWFM8800S VHF Marine Radiotelephone User Manual OPERTORS MANUAL

Furuno USA Inc VHF Marine Radiotelephone OPERTORS MANUAL

OPERTORS MANUAL

Navigation menu

Namespaces

Views

Navigation