Furuno USA 9ZWNX700A NAVTEX RECIEVER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	554664
Application ID	yF+9M249maHg0/7B1v5zaQ==
Document Description	USER MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	132.99kB (1662357 bits)
Date Submitted	2005-06-22 00:00:00
Date Available	2005-09-30 00:00:00
Creation Date	2005-05-20 09:59:30
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2005-05-20 10:52:27
Document Title	untitled

NAVTEX RECEIVER
NX-700A/B
IMPORTANT NOTICE
•
No part of this manual may be copied or reproduced without written permission.
•
If this manual is lost or worn, contact your dealer about replacement.
•
The contents of this manual and equipment specifications are subject to change without
notice.
•
The example screens (or illustrations) shown in this manual may not match the screens
you see on your display. The screen you see depends on your system configuration and
equipment settings.
•
This manual is intended for use by native speakers of English.
•
FURUNO will assume no responsibility for the damage caused by improper use or
modification of the equipment or claims of loss of profit by a third party.
•
Please carefully read and follow the operation and maintenance procedures set forth in
this manual.
•
Store this manual in a convenient place for further reference.
SAFETY INSTRUCTIONS
Safety information for the Operator
WARNING
CAUTION
ELECTRICAL SHOCK HAZARD
A warning label is attached to the equipment. Do not remove the label. If the
label is missing or damaged, contact
a FURUNO agent or dealer about
replacement.
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
WARNING
Do not disassemble or modify the
equipment.
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Fire, electrical shock or serious injury can
result.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Keep heater away from equipment.
A heater can melt the equipment's power
cord, which can cause fire or electrical
shock.
Use the proper fuse.
Fuse rating is shown on the equipment.
Use of a wrong fuse can result in damage
to the equipment.
ii
Name: Warning Label (1)
Type: 86-003-1011-1
Code No.: 100-236-231
Safety information for the Installer
CAUTION
WARNING
Do not open the equipment
unless totally familiar with
electrical circuits and
service manual.
Observe the following compass safe
distances to prevent deviation of a
magnetic compass.
Standard Steering
ELECTRICAL
SHOCK
HAZARD
Only qualified personnel
should work inside the
equipment.
Display unit
NX-700A
1.45 m
0.95 m
NX-700B
0.30 m
0.30 m
1.15 m
0.75 m
Receiver unit NX-7001
Turn off the power at the mains switchboard before beginning the installation.
Attach securely protective
earth to the ship's body.
Fire, electrical shock or serious injury can
result if the power is left on or is applied
while the equipment is being installed.
The protective earth is required
to the power supply to prevent
electrical shock.
iii
FORWORD
Congratulations on your choice of the FURUNO NX-700A/B NVTEX Receiver.
We are confident that you will enjoy many years of operation with this fine piece
of equipment.
For over 50 years, Furuno Electric Company has enjoyed an enviable reputation
for quality and reliability throughout the world. Our extensive global network of
agents and dealers furthers this dedication to excellence.
The NX-700A/B is just one of the many Furuno developments in the field of
marine radio communication.
NX-700A: Display unit w/printer
NX-700B: Display unit w/o printer
This NX-700A/B provides cost-effective price, high sensitivity and simple
operation in one compact and light-weight unit. In addition to its fundamental
function of receiving NAVTEX broadcasts, this unit can also function as nav data
display when connected to navigation equipment.
This unit is designed and constructed to ensure the user many years of
trouble-free operation. To obtain full performance from the equipment, however,
you should carefully read and follow the recommended procedures for
installation, operation and maintenance. No machine can perform its intended
functions unless it is installed and maintained properly.
Thank you for considering and purchasing FURUNO equipment.
iv
Features
NAVTEX (Navigational Telex) is a world wide coastal telex broadcasting system.
Coastal NAVTEX broadcasting stations with specific ID’s transmit Navigational
warnings. Meteorological warnings, Search and Rescue (SAR) information and
other navigational information for NAVTEX receiver-equipped vessels sailing in
coastal waters.
The FURUNO NX-700 NAVTEX receiver receives NAVTEX messages and
automatically displays them together with station ID and message category
information.
If ship’s position data is fed from navigation equipment, the NX-700
automatically decides in which NAVAREA the vessel is navigating, and selects
stations. (NAVAREAs are geographical zones defined by the international
Maritime Organization.)
-Meets the following standards and regulations
MSC.148 (77) IMO A.694 (17)
IEC 61097-6 Ed.2 CDV (2005-02)
IEC 60945 Ed. 3 and 4
IEC 61162-1 and 2
EN 300 065V 1.1.3
EN 301 011V 1.1.1 (1998-09)
ITU-R M 540-2
ITU-R M 625-3
-Receives 518 kHz and another (490 or 4209.5 kHz) at the same time
-5” LCD display
-Prints out the message selected
-Bright 76 x 100 mm, monochrome LCD, 240 x 320 dots with adjustable contrast
and brilliance
-Low power consumption
-Displays the NAV data or distance information at the bottom of screen
-Compact, stylish display, receiver and antenna units
TABLE OF CONTENTS
EQUIPMENT LISTS ............................................................................................. vi
SYSTEM CONFIGURATIONS ........................................................................... viii
1. PRINCIPLE OF NAVTEX SYSTEM ............................................................... 1-1
1.1
1.2
1.3
1.4
1.5
How NAVTEX Works ................................................................................................. 1-1
NAVTEX System Operation....................................................................................... 1-1
Message Format ....................................................................................................... 1-2
NAVTEX Station Map ................................................................................................ 1-3
NAVTEX Station List.................................................................................................. 1-4
2. OPERATION................................................................................................... 2-1
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
Operating Controls .................................................................................................... 2-1
Turn the Unit On/Off .................................................................................................. 2-1
Adjusting LCD Brilliance ............................................................................................ 2-2
Confirming the New Message.................................................................................... 2-2
Sample Messages..................................................................................................... 2-3
Choosing Up Navtex Station Receive Mode .............................................................. 2-4
Choosing the Local Frequency .................................................................................. 2-5
Editing the Setting for Frequencies............................................................................ 2-5
Switching the Frequency to Display........................................................................... 2-7
Alarm Messages........................................................................................................ 2-7
Processing Messages ............................................................................................... 2-8
Printing Messages..................................................................................................... 2-9
Editing the NAVTEX Station List ...............................................................................2-11
Icons ....................................................................................................................... 2-14
Messages List ......................................................................................................... 2-15
Other Functions....................................................................................................... 2-16
3. MAINTENANCE & TROUBLESHOOTING ................................................... 3-1
3.1
3.2
3.3
3.4
3.5
Maintenance.............................................................................................................. 3-1
Replacement of Fuse, Battery and Thermal Paper .................................................... 3-2
Troubleshooting......................................................................................................... 3-4
Diagnostics................................................................................................................ 3-5
Restoring All Default Settings .................................................................................... 3-6
4. INSTALLATION .............................................................................................. 4-1
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Display Unit ............................................................................................................... 4-1
Receiver Unit............................................................................................................. 4-3
Antenna Unit ............................................................................................................. 4-4
Printer (NX-700B only) .............................................................................................. 4-4
Wiring........................................................................................................................ 4-5
Setting of Printer........................................................................................................ 4-9
Interfacing ............................................................................................................... 4-10
vi
MENU TREE.................................................................................................... AP-1
PACKING LISTS ............................................................................................... A-1
DRAWINGS ....................................................................................................... D-1
INTERCONNECTION DIAGRAM.......................................................................S-1
SPECIFICATIONS ........................................................................................... SP-1
vii
EQUIPMENT LISTS
Standard Supply
Name
Display Unit
Receiver Unit
Antenna Unit
Installation
Materials
Spare Parts
Type
NX-700A
NX-700B
NX-7001
NX-7H
CP08-01810
CP08-01820
CP08-01870
CP08-01880
CP08-01890
Code No.
000-040-122
000-040-123
000-040-350
000-040-362
000-040-363
CP08-01860
000-040-349
CP08-01863*
004-514-530
CP08-01864*
004-514-540
CP08-01861*
SP08-02000*
SP08-02101*
004-514-350
000-040-344
004-514-370
viii
Qty
Remarks
w/printer
w/o printer
10 m cable, CP08-01811
20 m cable, CP08-01811*
30 m cable, CP08-01811*
40 m cable, CP08-01811*
50 m cable, CP08-01811*
DSUB25P cable, between
Display and Receiver Units
For Antenna Unit w/o antenna
cable
For Antenna Unit w/ antenna
cable.
For Display Unit
For NX-700A
Fuse for Receiver Unit
*: See the back of this manual.
Optional Supply
Name
Thermal Paper
Flush Mount Kit
AC-DC Power
Extension Cable
Coaxial Cable
Cable Assy
Right Angle
Mounting Base
L-Angle Mounting
Base
Handrail Mounting
Base
Mast Mounting Kit
Display Unit
Type
TP058-30CL
OP08-19
OP08-20
PR-240-CE
Code No.
000-154-047
004-514-810
004-514-820
000-053-373
000-041-174
000-041-175
OP04-2
000-041-176
000-041-177
000-041-178
005-948-250
005-948-260
OP08-12
005-948-270
005-948-280
005-948-290
000-563-048
RG-10/U-Y
000-126-000
000-126-001
000-152-698
000-152-699
DSUB25P-DSUB25P
000-152-700
000-152-701
No.13-QA330
000-803-239
No.13-QA310
000-803-240
No.13-RC5160
000-806-114
CP20-01111
NX-700A
NX-700B
004-365-780
ix
Qty
1 set
Remarks
For NX-700A, 10 rolls
For NX-700A
For NX-700B
10 m, w/M-A-JJ connector
20 m, w/M-A-JJ connector
30 m, w/M-A-JJ connector
40 m, w/M-A-JJ connector
50 m, w/M-A-JJ connector
10 m
20 m
30 m
40 m
50 m
30 m
40 m
50 m
3m
5m
For 24 VDC
10 m
15 m
For antenna unit NX-7H
SYSTEM CONFIGURATIONS
DISPLAY UNIT
NX-700A
DISPLAY UNIT
NX-700B
ANTENNA UNIT
NX-7H
or
Max. 15 m
Max. 100 m
RECEIVER UNIT
NX-7001
External Alarm
Rectifier
PR-240
Printer (700B only)
INS
Power supply
Power supply
12-24 VDC
100/110/115/
200/220/230 VAC.
1 , 50/60 Hz
PC Converter
: Standard
: Option
: User supply
Environmental Category
Antenna unit
To be installed in an exposed area
Display unit
Receiver unit
To be installed in a protected area
PC
1.
PRINCIPLE OF NAVTEX SYSTEM
1.1
How NAVTEX Works
There are many types of navigational and meteorological information available
on radio, such as NAVAREA, HYDROPAC, etc. However, these systems rely
heavily upon the operator's experience and skill in tuning the radio and
interpreting messages. In addition, constant monitoring to pick up wanted
information among a vast volume of messages is not practical with a limited
radio staff.
To provide all mariners with up-to-the-minute information automatically, the
NAVTEX system was developed.
NAVTEX is an acronym meaning Navigational Telex, and as its name shows, it is
a kind of narrow band radio teletype system for sending (by frequency shift
keying) text messages expressed in a 7-unit code. The difference is that a
NAVTEX transmitter transmits nine control characters (header code) ahead of
the main message, so that the receiver can identify the station, message type
and serial number automatically.
1.2
NAVTEX System Operation
For navigation purposes, the world is divided into 16 areas as shown in the
figure below. Each Navtex station has an identification code, from “A” to “Z”. The
frequency assigned to Navtex are 518 kHz and another (490 or 4209.5 kHz),
and many station exist in the same service coverage.
If the stations were to transmit without any rule, the system would collapse due
to mutual interference. To avoid this problem, the following rules apply.
• The transmission schedule is determined so that two or more stations having
a common service area may not overlap in time.
• Each station transmits with minimum required power to cover its service area
(200 nautical miles nominal).
1-1
1. PRINCIPLE OF NAVTEX SYSTEM
1.3
Message Format
For automatic identification of messages, each message starts with nine control
characters, called “Header codes”.
The first five characters are always “ZCZC_“ and common to all messages. This
part is used for message synchronization. The latter four characters are
designed as b1, b2, b3 and b4 indicate origin, category and serial number of the
message.
Character B1 is the identification letter of the Navtex station “A” thru “Z”.
Character B2 indicates the type of message. “A” thru “Z”, as listed below.
Character B3 and B4 indicate the serial number of the message. The serial
numbers are counted up from “01” to “99”, and starts from “01” again. Number
“00” is specially reserved for important emergency messages, such as a search
and rescue (SAR) message.
The end of each message is indicated by “NNNN” (four successive N’s).
General message format is summarized below.
Header code
ZCZC
B1 B2 B3 B4
main message
Start code
(sync)
Main message
NNNN
Termination code
Serial number
"00": Emergency message
"01" - "99": Normal message
Type of message
"A" - "Z"
(See the list below.)
Station ID
"A" - "Z"
1-2
A:
[Type of message (category)]
Navigational warning
I:
OMEGA message
B:
Meteorological warning
J:
Differential OMEGA message
C:
Ice report
K:
Other electronic navigational aid
system message
D:
Search and rescue
information/piracy and armed
robbery
L:
Navigational warning (additional)
E:
Meteorological forecast
M to U:
Reserve-presently not used
F:
Pilot message
V:
Notice to Fishermen (U. S. only)
G:
DECCA message
W to Y:
Reserve-presently not used
H:
LORAN-C message
Z:
QRU (no message on hand)
1. PRINCIPLE OF NAVTEX SYSTEM
1.4
NAVTEX Station Map
1-3
1. PRINCIPLE OF NAVTEX SYSTEM
1.5
NAV
area
NAVTEX Station List
Station
Country
Longitude
Frequen Area Station
cy (kHz) (nm)
ID
Broadcast schedule (UTC)
Belgium
Oostende
51 11 N
02 48 E
518
55
0310, 0710, 1110, 1510, 1910, 2310
Estonia
Tallinn
59 30 N
24 30 E
518
250
0320, 0720, 1120, 1520, 1920, 2320
518
550
0250, 0650, 1050, 1450, 1850, 2250
Iceland
Reykjavik Radio
64 05 N
21 51 W
490
550
0318, 0718, 1118, 1518, 1918, 2318
Ireland
Valentia
51 27 N
09 49 W
518
400
0340, 0740, 1140, 1540, 1940, 2340
Malin Head
55 22 N
07 21 W
518
400
0240, 0640, 1040, 1440, 1840, 2240
France
Niton
50 35 N
01 18 W
518
270
0140, 0540, 0940, 1340, 1740, 2140
Netherlands
Den Helder
52 06 N
04 15 E
518
110
0230, 0630, 1030, 1430, 1830, 2230
Norway
Bodo Radio
67 16 N
14 23 E
518
450
0010, 0410, 0810, 1210, 1610, 2010
Rogaland Radio
58 48 N
05 34 E
518
450
0150, 0550, 0950, 1350, 1750, 2150
Vardoe Radio
70 22 N
31 06 E
518
450
0330, 0730, 1130, 1530, 1930, 2330
Svalbard
78 04 N
13 38 E
518
450
0000, 0400, 0800, 1200, 1600, 2000
Orlandet
63 40 N
09 33 E
518
450
0210, 0610, 1010, 1410, 1810, 2210
Bjuroklubb
64 28 N
21 36 E
518
300
0110, 0510, 0910, 1310, 1710, 2110
Gislovshammar
55 29 N
14 19 E
518
300
0130, 0530, 0930, 1330, 1730, 2130
Grimeton
57 06 N
12 23 E
518
300
0030, 0430, 0830, 1230, 1630, 2030
518
270
0100, 0500, 0900, 1300, 1700, 2100
Cullercoats
55 02 N
01 26 W
490
270
0320, 0720, 1120, 1520, 1920, 2320
518
270
0220, 0620, 1020, 1420, 1820, 2220
490
270
0020, 0420, 0820, 1220, 1620, 2020
518
270
0040, 0440, 0840, 1240, 1640, 2040
490
270
0120, 0520, 0920, 1320, 1720, 2120
518
150
0200, 0600, 1000, 1400, 1800, 2200
518
300
0000, 0400, 0800, 1200, 1600, 2000
490
300
0040, 0440, 0840, 1240, 1640, 2040
Sweden
United
Kingdom
Portpatrick
Niton
II
Latitude
France
Portugal
Spain
54 51 N
50 35 N
05 07 W
01 18 W
Oostende
51 11 N
02 48 E
Cross Corsen
48 28 N
05 03 W
Niton
50 35 N
01 18 W
490
270
0310, 0710, 1110, 1510, 1910, 2310
Horta
38 32 N
28 38 W
518
640
0050, 0450, 0850, 1250, 1650, 2050
518
530
0250, 0650, 1050, 1450, 1850, 2250
Monsanto
38 44 N
09 11 W
490
530
0100, 0500, 0900, 1300, 1700, 2100
Coruna
43 21 N
08 27 W
518
400
0030, 0430, 0830, 1230, 1630, 2030
Tarifa
36 01 N
05 34 W
518
400
0100, 0500, 0900, 1300, 1700, 2100
Las Palmas
28 10 N
15 25 W
518
400
0120, 0520, 0920, 1320, 1720, 2120
(Continued on next page)
1-4
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
III
Country
Latitude
Longitude
Frequen
Area
Station
cy (kHz)
(nm)
ID
Broadcast schedule (UTC)
Bulgaria
Varna
43 04 N
27 46 E
518
350
0130, 0530, 0930, 1330, 1730, 2130
Croatia
Split radio
43 30 N
16 29 E
518
85
0240, 0640, 1040, 1440, 1840, 2240
Cyprus
Cypradio
35 03 N
33 17 E
518
200
0200, 0600, 1000, 1400, 1800, 2200
Egypt
Alexandria
31 12 N
29 52 E
518
350
0210, 0610, 1010, 1410, 1810, 2210
Serapeum
30 28 N
32 22 E
4209.5
0750, 1150
Toulon
43 06 N
05 59 E
France
Greece
518
250
0340, 0740, 1340, 1540, 1940, 2340
490
250
0300, 0700, 1100, 1500, 1900, 2300
Iraklion
35 20 N
25 07 E
518
280
0110, 0510, 0910, 1310, 1710, 2110
Kerkyra
39 37 N
19 55 E
518
280
0140, 0540, 0940, 1340, 1740, 2140
Limnos
39 52 N
25 04 E
518
280
0150, 0550, 0950, 1350, 1750, 2150
Israel
Haifa
32 49 N
35 00 E
518
200
0020, 0420, 0820, 1220, 1620, 2020
Italy
Roma
41 48 N
12 31 E
518
320
0250, 0650, 1050, 1450, 1850, 2250
Augusta
37 14 N
15 14 E
518
320
0330, 0730, 1130, 1530, 1930, 2330
Cagliari
39 14 N
09 14 E
518
320
0310, 0710, 1110, 1510, 1910, 2310
Trieste
45 41 N
13 46 E
518
320
0320, 0720, 1120, 1520, 1920, 2320
Malta
Malta
35 49 N
14 32 E
518
400
0220, 0620, 1020, 1420, 1820, 2220
Russian
Federation
Novorossiysk
44 42 N
37 44 E
518
300
0300, 0700, 1100, 1500, 1900, 2300
Spain
Cabo de la Nao
38 43 N
00 09 E
518
300
0350, 0750, 1150, 1550, 1950, 2350
Turkey
Istanbul
41 04 N
28 57 E
518
300
0030, 0430, 0830, 1230, 1630, 2030
Samsun
41 17 N
36 20 E
518
300
0040, 0440, 0840, 1240, 1640, 2040
Antalya
36 53 N
30 42 E
518
300
0050, 0450, 0850, 1250, 1650, 2050
Izmir
38 22 N
26 36 E
518
300
0120, 0520, 0920, 1320, 1720, 2120
Mariupol
47 06 N
37 33 E
518
280
0100, 0500, 0900, 1300, 1700, 2100
Odessa
46 29 N
30 44 E
518
280
0230, 0630, 1030, 1430, 1830, 2230
Bermuda
32 23 N
64 41 W
518
280
0010, 0410, 0810, 1210, 1610, 2010
Riviere-au-Renard
50 11 N
66 07 W
518
300
0020, 0420, 0820, 1220, 1620, 2020
0035, 0435, 0835, 1235, 1635, 2035
Wiarton
44 20 N
81 10 W
518
300
0110, 0510, 0910, 1310, 1710, 2110
St. Johns
47 30 N
52 40 W
518
300
0220, 0620, 1020, 1420, 1820, 2220
Thunder Bay
48 25 N
89 20 W
518
300
0230, 0630, 1030, 1430, 1830, 2230
Sydney, NS
46 10 N
60 00 W
518
300
0240, 0640, 1040, 1440, 1840, 2240
0255, 0655, 1055, 1455, 1855, 2255
Yarmouth
43 45 N
66 10 W
518
300
0320, 0720, 1120, 1520, 1920, 2320
0335, 0735, 1135, 1535, 1935, 2335
Ukraine
IV
Station
Bermuda
(UK)
Canada
(Continued on next page)
1-5
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
IV
Country
Canada
United States
Netherlands
Antilles
Station
Latitude
Longitude
Labrador
53 42 N
57 01 W
Iqaluit, NU
63 43 N
68 33 W
518
300
0350, 0750, 1150, 1550, 1950, 2350
518
300
0310, 0710, 1110, 1510, 1910, 2310
490
300
0300, 0700, 1100, 1500, 1900, 2300
Broadcast schedule (UTC)
518
240
0000, 0400, 0800, 1200, 1600, 2000
Boston
41 43 N
70 30 W
518
200
0445, 0845, 1245, 1645, 2045, 0045
New Orleans
29 53 N
89 57 W
518
200
0300, 0700, 1100, 1500, 1900, 2300
Portsmouth
36 43 N
76 00 W
518
280
0130, 0530, 0930, 1330, 1730, 2130
Isabella
18 28 N
67 04 W
518
200
0200, 0600, 1000, 1400, 1800, 2200
Savannah, GA
32 08 N
81 42 W
518
200
0040, 0440, 0840, 1240, 1640, 2040
Curacao
12 10 N
68 52 W
518
400
0110, 0510, 0910, 1310, 1710, 2110
なし
Argentina
Uruguay
IX
ID
80 23 W
Ushaia
54 48 S
68 18 W
518
280
0200, 0600, 1000, 1400, 1800, 2200
Rio Gallegos
51 37 S
65 03 W
518
280
0210, 0610, 1010, 1410, 1810, 2210
45 51 S
67 25 W
518
280
0220, 0620, 1020, 1420, 1820, 2220
Bahia Blanca
38 43 S
62 06 W
518
280
0230, 0630, 1030, 1430, 1830, 2230
Mar del Plata
38 03 S
57 32 W
518
280
0240, 0640, 1040, 1440, 1840, 2240
Buenos Aires
34 36 S
58 22 W
518
560
0250, 0650, 1050, 1450, 1850, 2250
518
280
0050, 0450, 0850, 1250, 1650, 2050
La Paloma
34 40 S
54 09 W
490
280
0000, 0400, 0800, 1200, 1600, 2000
Rivadavia
VIII
Station
(nm)
25 37 N
Comodoro
VII
Area
cy (kHz)
Miami
VI
Frequen
Namibia
Walvis Bay
23 03 S
14 37 E
518
378
0010, 0410, 0810, 1210, 1610, 2010
South Africa
Cape Town
33 40 S
18 43 E
518
500
0020, 0420, 0820, 1220, 1620, 2020
Port Elizabeth
34 02 S
25 33 E
518
500
0120, 0520, 0920, 1320, 1720, 2120
Durban
30 00 S
31 30 E
518
500
0220, 0620, 1020, 1420, 1820, 2220
Mumbay
19 05 N
72 50 E
518
250
0100, 0500, 0900, 1300, 1700, 2100
Madras
13 08 N
80 10 E
518
0230, 0630, 1030, 1430, 1830, 2230
Mauritius
Mauritius Radio
20 10 S
57 28 E
518
400
0020, 0420, 0820, 1220, 1620, 2020
Bahrain
Hamala
26 09 N
50 28 E
518
300
0010, 0410, 0810, 1210, 1610, 2010
518
200
0350, 0750, 1150, 1550, 1950, 2350
Egypt
Serapeum
30 28 N
32 22 E
0750, 1150
India
4209.5
Iran
Kosseir
26 06 N
34 17 E
518
400
0330, 0730, 1130, 1530, 1930, 2330
Bushehr
28 59 N
50 50 E
518
300
0000, 0400, 0800, 1200, 1600, 2000
Bandar Abbas
27 07 N
56 04 E
518
300
0050, 0450, 0850, 1250, 1650, 2050
(Continued on next page)
1-6
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
IX
Station
Country
Latitude
Longitude
Frequen
cy (kHz)
Area
(nm)
Station
ID
Saudi Arabia
Jeddah
21 23 N
39 10 E
518
390
0705, 1305, 1905
Oman
Muscat
23 36 N
58 30 E
518
270
0200, 0600, 1000, 1400, 1800, 2200
Pakistan
Karachi
24 51 N
67 03 E
518
400
0230, 0630, 1030, 1430, 1830, 2230
なし
XI
Broadcast schedule (UTC)
China
Indonesia
Japan
Korea,
Republic of
Sanya
18 14 N
109 30 E
518
250
0200, 0600, 1000, 1400, 2200
Guangzhou
23 08 N
113 32 E
518
250
0210, 0610, 1010, 1410, 2210
Fuzhou
26 01 N
119 18 E
518
250
0220, 0620, 1020, 1420, 2220
Shanghai
31 08 N
121 33 E
518
250
0240, 0640, 1040, 1440, 2240
Dalian
38 52 N
121 31 E
518
250
0250, 0650, 1050, 1450, 2250
Jayapura
02 31 S
140 43 E
518
300
0000, 0400, 0800, 1200, 1600, 2000
Ambon
03 42 S
128 12 E
518
300
0010, 0410, 0810, 1210, 1610, 2010
Makassar
05 06 S
119 26 E
518
300
0030, 0430, 0830, 1230, 1830, 2030
Jakarta
06 06 S
106 54 E
518
300
0040, 0440, 0840, 1240, 1640, 2040
Otaru
43 19 N
140 27 E
518
400
0130, 0530, 0930, 1330, 1730, 2130
Kushiro
42 57 N
144 36 E
518
400
0140, 0540, 0940, 1340, 1740, 2140
Yokohama
35 14 N
139 55 E
518
400
0120, 0520, 0920, 1320, 1720, 2120
Moji
34 01 N
130 56 E
518
400
0110, 0510, 0910, 1310, 1710, 2110
Naha
26 05 N
127 40 E
518
400
0100, 0500, 0900, 1300, 1700, 2100
518
200
0330, 0730, 1130, 1530, 1930, 2330
Chukpyong
37 03 N
129 26 E
490
200
0130, 0530, 0930, 1330, 1730, 2130
518
200
0340, 0740, 1340, 1540, 1940, 2340
490
200
0140, 0540, 0940, 1340, 1740, 2140
Pyongsan
Malaysia
35 36 N
126 29 E
Penang
05 26 N
100 24 E
518
350
0320, 0720, 1120, 1520, 1920, 2320
Miri
04 28 N
114 01 E
518
350
0310, 0710, 1110, 1510, 1910, 2310
Sandakan
05 54 N
118 00 E
518
350
0300, 0700, 1100, 1500, 1900, 2300
Singapore
Singapore
01 25 N
103 52 E
518
400
0020-0030, 0420-0430, 0820-0830,
1220-1230, 1620-1630, 2020-2030
Thailand
Bangkok Radio
13 43 N
100 34 E
518
200
0050, 0450, 0850, 1250
United States
Guam
13 29 N
144 50 E
518
100
0100, 0500, 0900, 1300, 1700, 2100
(Continued on next page)
1-7
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
XI
Vietnam
Taiwan
Associate
Member of IMO
XII
Canada
United States
XIII
Station
Latitude
Longitude
Ho Chi Minh City
10 47 N
106 40 E
Haiphong
20 44 N
106 44 E
Country
Russian
Federation
XVI
Area
Station
cy (kHz)
(nm)
ID
518
400
0350, 0750, 1150, 1550, 1950, 2350
490
400
0340, 1540
4209.5
400
0230, 0630, 1030, 1430, 1830, 2230
0140, 0540, 0940, 1340, 1740, 2140
Broadcast schedule (UTC)
Danang
16 05 N
108 13 E
518
400
Kaohsiung
22 29 N
120 25 E
518
400
Hong Kong
22 13 N
114 15 E
518
400
0150, 0550, 0950, 1350, 1750, 2150
Prince Rupert
54 20 N
130 20 W
518
300
0030, 0430, 0830, 1230, 1630, 2030
Tofino
48 55 N
125 35 W
518
300
0110, 0510, 0910, 1310, 1710, 2110
San Francisco
37 55 N
122 44 W
518
350
0400, 0800, 1200, 1600, 2000, 2400
Kodiak
57 46 N
152 34 W
518
200
0300, 0700, 1100, 1500, 1900, 2300
Honolulu
21 22 N
158 09 W
518
350
0040, 0440, 0840, 1240, 1640, 2040
Cambria
35 31 N
121 03 W
518
350
0445, 0845, 1245, 1645, 2045, 0045
Astoria
46 10 N
123 49 W
518
216
0130, 0530, 0930, 1330, 1730, 2130
Kholmsk
47 02 N
142 03 E
518
300
0010, 0410, 0810, 1210, 1610, 2010
Murmansk
68 46 N
32 58 E
518
300
0020, 0420, 0820, 1220, 1620, 2020
Arkhangelsk
64 51 N
40 17 E
518
300
0050, 0450, 0850, 1250, 1650, 2050
Astrakhan
45 47 N
47 33 E
518
250
0340, 0740, 1140, 1540, 1940, 2340
0400, 1200, 2000
0000, 0800, 1600
0410, 1210, 2010
0010, 0810, 1610
0420, 1220, 2020
0020, 0820, 1620
0430, 1230, 2030
0030, 0830, 1630
0440, 1240, 2040
0040, 0840, 1640
0230, 0630, 1030, 1430, 1830, 2230
なし
XIV
XV
Frequen
Chile
Peru
Antofagasta
23 40 S
70 25 W
518
300
Valparaiso
32 48 S
71 29 W
518
300
Talcahuano
36 42 S
73 06 W
518
300
Puerto Montt
41 30 S
72 58 W
518
300
Punta Arenas
53 09 S
70 58 W
518
300
Isla de Pascua
27 09 S
109 25 W
518
300
Paita
05 05 S
81 07 W
518
Callao
12 03 S
77 09 W
Mollendo
17 01 S
72 01 W
0450, 1250, 2050
0050, 0850, 1650
200
0300, 0700, 1100, 1500, 1900, 2300
518
200
0320, 0720, 1120, 1520, 1920, 2320
518
200
0340, 0740, 1140, 1540, 1940, 2340
Note: The list shows the stations listed at Longwave Navtex Broadcasts (Oct. 2004).
1-8
2.
OPERATION
2.1
Operating Controls
Registers items on menus.
Cursor pad
-Shifts the cursor and display.
-Selects items on menus.
ENT
MENU
ESC
Opens menu/Returns to the previous display.
LIST
Opens the LIST menu.
PRINT
Opens the PRINT menu.
DIM
Turns the power on/off.
Adjusts the brilliance.
+: Raises the setting.
- : Decreases the setting.
Display unit, front view
2.2
Turning the Unit On/Off
Press the
key to turn the unit on. A beep sounds and the equipment shows
the start up display, where the ROM and ROM are checked for proper operation
and the program no. is displayed. The results of the check are shown as OK or
NG (No Good).
When the results are OK, the list display is shown after five seconds after
completion of the check, with frequency last used before turning the power off.
DUAL CHANNEL NAVTEX
NX-700
FURUNO ELECTRIC CO., LTD.
ROM : OK
RAM : OK
Program No. 0850193-XX
To turn the power off, press the
XX: Program version No.
key again.
2-1
2. OPERATION
Note: If NG appears for any test, try to press any key to go to the next stage.
The equipment, however, may not be operated properly. Contact your
dealer if the problem persists.
2.3
Adjusting LCD Dimmer
You can adjust LCD brilliance with the + DIM – key. The adjustment range is 0
(dark) to 9 (bright).
+: Raises the dimmer.
-: Decreases the dimmer.
2.4
Confirming the New Message
When you receive a new message, do one of the following depending on
message received.
SAR (Search and Rescue) message
1. When receiving an SAR message is received, the audible alert sounds and
details for the SAR message appear.
Icon for SAR message
2. Press any key other than
key to silence the alarm.
Other messages
1. When a message other than an SAR message is received, the display shows
one of the following windows.
Received new int'l msg.
Received new local msg.
Display new msg ?
Yes No
Display new msg ?
Yes No
International message
Local message
2. If you want to read the message immediately, press ◄ to choose “Yes” and
then press the ENT key. to display the message
To read the message later, choose “No” and then press the ENT key to close
the window.
Note: In the default setting, all received messages are printed out automatically.
For further details, see paragraph 2-12.
2-2
2. OPERATION
2.5
Sample Messages
Press ▲▼ on the cursor pad to choose a message, and then press the ENT key
to show the detailed information for that message. These displays can be
switched by pressing the ENT key.
Frequency (paragraph 2.9)
Station ID, type of message, serial No. (paragraph 1.3)
Status icon (paragraph 2.14)
Error rate
No. of saved messages
Category of messages
(paragraph 2.11)
Receiving
date
New
ENT key
Old
Operation guide
Message icon (paragraph 2.14)
Message list
Detailed message
Note 1: The operation guide at the bottom of screen shows the functions of the
keys available for use with the current screen.
Note 2: The character size can be changed. For detail, see page 2-17.
Key
▲▼
◄►
MENU
ENT
LIST
PRINT
Display mode
List
Detailed
List
Detailed
List
Detailed
List
Detailed
List
Detailed
List
Detailed
Function
Scrolls the list.
Scrolls the message.
Changes the frequency.
Shows the newer (◄) or older (►) message.
Shows the main menu.
Shows the detailed message selected.
Shows the message list.
Shows the list window. (P2-6)
Shows the print window. (P2-7)
2-3
2. OPERATION
2.6
Choosing Up Navtex Station Receive Mode
The NAVTEX menu allows you to select what station to receive, automatically,
manually or from the INS connected. The Auto mode requires navigation data,
and stations are automatically selected according to the distance between own
ship and NAVTEX stations. If navigation data is not input, all stations are
selected. The manual mode lets you freely stations to receive. The INS mode
allows you to set the station, message and local channel from the Integrated
Navigation System connected.
1. Press the MENU/ESC key to show the main menu.
Menu
NAVTEX
System
Display
Service
Main menu
2. Press ▲ or ▼ to choose NAVTEX.
3. Press the ENT key or ► to open the NAVTEX menu.
NAVTEX
Receive Mode Manual
Local Channel 490kHz
Auto Print
All
Rcv Station & Msg
User Select Station & Msg
NAVTEX menu
4. Press ▲ or ▼ to choose Receive Mode, and then press the ENT key or ► to
show the receive mode options.
INS
Auto
Manual
Receive mode options
5. Press ▲ or ▼ to choose INS, Auto or Manual as appropriate, and then press
the ENT key.
6. Press the MENU/ESC key several times to close the menu.
2-4
2. OPERATION
2.7
Choosing the Local Frequency
You can choose 490 kHz or 4209.5 kHz as the local frequency. This function is
only available for the Auto and Manual modes. (See paragraph 2.6.)
1. Press the MENU/ESC key to show the main menu.
2. Press ▲ or ▼ to choose NAVTEX, and then press the ENT key or ►.
3. Press ▲ or ▼ to choose Local Channel, and then press the ENT key or ► to
show the local channel options.
490kHz
4209.5kHz
Local channel options
4. Press ▲ or ▼ to choose the frequency 490 kHz or 4209.5 kHz, and then
press the ENT key.
5. Press the MENU/ESC key several times to close the menu.
2.8
Editing the Settings for Frequencies
Stations and messages for receiving/displaying on each frequency can be edited
as below.
Rcv Station & Msg
(Station)
You can receive messages by station when Manual is chosen as the Receive
Mode on the NAVTEX menu.
(Message)
You can choose the messages to receive when Manual or Auto is chosen as the
Receive Mode on the NAVTEX menu. Note that A/B/D/L cannot be rejected.
User Select Station & Msg
(Station)
Choose the station to display on User Selected Messages, which is shown when
the LIST key is pressed.
(Message)
Choose the type of message to display on User Selected Messages, which is
shown when the LIST key is pressed.
Note 1: For messages, the alarm message is displayed always.
Note 2: When User Select is chosen as the Auto Print on NAVTEX menu, only
the messages chosen here are printed. (See paragraph 2-12.)
1. Press the MENU/ESC key to show the main menu.
2. Press ▲ or ▼ to choose NAVTEX, and then press the ENT key or ►.
2-5
2. OPERATION
3. Press ▲ or ▼ to choose Rcv Station & Msg or User Select Station & Msg.
4. Press the ENT key to open the appropriate editing window. (Below is the Rcv
Station Msg editing window.)
Recieve mode
Rcv Station & Msg
Internaitional frequency
Station
[Auto]
[518]
Station
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Message
Message
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Local frequency*
[490]
Station
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Message
Changeable item
ABCDEFGHIJKLMNOPQRSTUVWXYZ
[ ][ ] MOVE
[ENT] EDIT [MENU] RETURN TO MENU
*: Local channel selected at Paragraph 2.7.
Edit window (ex. Rcv Station & Msg)
5. Press ▲ or ▼ to choose the item to edit, and then press the ENT key to
show the alphabet selection window.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Cursor
6. Press ◄ or ► to choose the alphabet desired, and then press ▲ or ▼ to
choose it as is or “-“ (disable).
7. Press the ENT key
8. Repeat steps 5 through 7 to complete.
9. Press the MENU/ESC key to close the window.
2-6
2. OPERATION
2.9
Switching the Frequency to Display
With the message list shown, you can switch the frequency to 518 kHz or 490
(or 4209) kHz by pressing ◄ or ► key.
Press
518
490 (4209)
Switching the frequency for display
2.10
Alarm Messages
The sequence of events when an alarm message is received is as shown below.
When receiving SAR (Search and Rescue) message:
The audible alarm beep sounds, and the alarm output signal is set to ON. The
SAR message is shown on the display immediately after receiving. Note that the
setting of the LIST window changes to All Messages automatically when
receiving an SAR message. (See paragraph 2.11.)
When receiving WARNING message (A/B/L):
When the Warn Msg Alm on System menu is set to On, the audible alarm
sounds and the alarm output signal is ON. The message received appears.
Silencing audible alarm
Press any key (except
key).
2-7
2. OPERATION
2.11
Processing Messages
Choosing messages to display
You can choose which category of messages to display: All, Alarm, User
Selected and Good messages.
1. With the message list or detailed message shown, press the LIST key to
show the list options.
All Messages
Alarm Messages
User Messages
Good Messages
Lock Message
List options
2. Press ▲ or ▼ to choose the item.
All Messages: Shows all messages received.
Alarm Messages: Shows only SAR/WARNING messages.
User Selected Messages: Shows messages arranged at User Select Station &
Msg on NAVTEX menu.
Good Messages: Shows messages whose error rate is less than 4%.
3. Press the ENT key to close the window.
The list chosen at step 2 appears.
Note: When the following messages appear, set the List window to All Messages
to show.
Urgent message:
“Message not chosen for display received; it is a int’l (or local) 00 message.
Choose “All Message” (LIST menu) to display.”
Normal message:
Int’l (or local) message not chosen for display received. Choose “All
Message” (LIST menu) to display.”
2-8
2. OPERATION
Protecting message from deleting
Messages are automatically deleted from the memory under the following
conditions.
-66 hours passed from the moment when received.
-Older than No. 200
To prevent a message from being deleted, choose the message and then select
Lock Message from the list window. The protect icon ( ) appears next to the
message selected. To unlock a message, choose it and then select Unlock
Message in the same window. (The protect icon disappears.)
Note 1: When you unlock a message which was received 66 hours ago or a
message that is older than No. 200, it will be deleted promptly when
unlocked.
Note 2: Maximum 50 messages for International and local (or 25% of each
memory) can be protected.
2.12
Printing Messages
Received messages can be printed automatically or manually, from the built-in
printer (NX-700A) or external printer (NX-700B).
Printing all messages displayed
Displayed messages can be arranged on the LIST menu described in paragraph
2.11.
1. Press the PRINT key when all messages are shown on display to show the
PRINT options.
Print
Cancel Print
Print options
2. Press ▲ or ▼ to choose “Print”.
3. Press the ENT key to print.
Note: When a message is received while printing some messages, the new one
cannot be printed.
Printing each message text
1.
2.
3.
4.
5.
Press ▲ or ▼ to choose the desired message from the list.
Press the ENT key to show the detailed information.
Press the PRINT key.
Press ▲or ▼ to choose “Print” from the window.
Press the ENT key to print.
2-9
2. OPERATION
Printing messages automatically
1. Press the MENU/ESC key to open the main menu.
2. Press ▲ or ▼ to choose NAVTEX, and then press the ENT key to show the
NAVTEX menu.
3. Press ▲ or ▼ to choose Auto Print, and then press the ENT key to open the
auto print options.
Off
All
User Select
Auto print options
4. Press ▲ or ▼ to choose All, User Select or Off as appropriate.
All: Prints all messages.
User Select: Prints only the specified messages at User Select Station & Msg
on the NAVTEX menu.
Off: All messages are not printed automatically.
5. Press the ENT key.
6. Pres the MENU/ESC key several times to close the menu.
Canceling printing
When a menu disappears, you cannot cancel the printing.
1. Press the PRINT key while showing the messages to open the print window.
2. Press ▼ to choose “Cancel Print” and then press the ENT key.
2-10
2. OPERATION
2.13
Editing the NAVTEX Station List
Maximum 300 NAVTEX stations can be registered into the memory.
Note: To cancel editing of a NAVTEX station, press the MENU/ESC key. The
message “Exit without saving?” appears. Choose “Yes”, and then press
ENT key.
Adding NAVTEX station
You may add a NAVTEX station to the NAVTEX station list as follows:
1. Press the MENU/ESC key to show the main menu.
2. Press ▲ or ▼ to choose Service, and then press the ENT key.
Service
INS Input Speed
4800bps
INS Output Speed 4800bps
Print Header
On
Edit Station List
Default Setting
Test
Rcv Monitor
Service menu
3. Press ▲ or ▼ to choose Edit Station List, and then press the ENT key.
Frequency
NAV Area
Station name
518kHz
NavArea
01
[ New ]
Oostende
Tallinn
Reykjavik Radio
Valentia
Malin Head
Niton
Den Helder
Bodo Radio
Rogaland Radio
Vardoe Radio
Svalbard
T, - , U, - , R, - , W,- , Q, - , K, - , P, - , B, - , L, - , V, - , A, - , -
[ ][ ] CHANGE NAVAREA
[LIST] CHANGE FREQ
[ENT] EDIT [MENU] RETURN TO MENU
Edit station list display
4. Confirm that New is chosen, and then press the ENT key to show the
addition window appears.
2-11
2. OPERATION
NAV Area
Station Name
Latitude
Longitude
Station ID
Sertvice Area
NavArea
Station
Latitude
Longitude
518kHz
490kHz
4209.5kHz
Range
0 00'N
0 00'E
ID1: - ID2: - ID3: ID1: - ID2: - ID3: ID1: - ID2: - ID3: 400nm
Save data ?
New addition window
5. Confirm that NavArea is chosen, and then press the ENT key to show the
area No. window.
6. Press ▲ or ▼ to choose a Nav area No. (1 to 16, and EXT), and then press
the ENT key.
For NAV area No., see paragraph 1.4. EXT is reserved for future use.
7. Confirm that Station is chosen, and then press ENT key.
8. Enter a station name (Max. 18 characters), and then press the ENT key.
a) Press ▲ or ▼ to choose a character. Each press of ▲ shows A -> … -> Z ->
a -> … -> z -> 0 -> … -> 9 -> _ -> - -> space in that sequence.
b) Press ► to move the cursor to next digit.
c) Repeat steps a) and b) to complete the station name.
9. Confirm that Latitude is chosen, and then press the ENT key.
10. Enter the latitude for station, and then press the ENT key.
Use ▲ or ▼ to switch to North and South.
11. Confirm that Longitude is chosen, and then press the ENT key.
12. Enter the longitude for station, and then pres the ENT key.
Use ▲ or ▼ to switch to East and West.
13. Confirm that 518kHz, 490kHz or 4209.5kHz is chosen, press the ENT key.
14. Enter the station ID (A to Z), and then press the ENT key.
For multiple stations, fill in ID2 and ID3.
15. Confirm that Range is chosen, and then press the ENT key.
16. Enter the service area (1 to 999 nm), and then press the ENT key.
17. Confirm that Save data? is chosen, and then press the ENT key.
The message “Save new station?” appears.
18. Press ◄ to choose “Yes”, and then press ENT key to close the new addition
window disappears.
Note: If the station ID was not entered at step 14, the message “Enter ID
data.” appears. Press any key, and then enter the station ID.
19. To enter another NAVTEX station, repeat steps 4 through 18.
20. Press the MENU/ESC key several times to close the menu.
2-12
2. OPERATION
Editing NAVTEX station
Existing NAVTEX station may be edited as follows:
1.
2.
3.
4.
5.
Press the MENU/ESC key to show the main menu.
Press ▲ or ▼ to choose Service, and then press the ENT key.
Press ▲ or ▼ to choose Edit Station List, and then press the ENT key.
Press ◄ or ► to choose the NAV area to be changed (01 to 06, EXT).
Press the LIST key to choose the frequency to be changed (518kHz, 490kHz
or 4209.5kHz).
6. Press ▲ or ▼ to choose the station, and then press the ENT key.
Edit
Delete
7. Press ▲ to choose “Edit”, and then press ENT key to show the edit window
appears.
Oostende
NAV Area
Station Name
Latitude
Longitude
Station ID
Service Area
NavArea
Station
Oostende
Latitude
51 11'N
Longitude
2 48'E
518kHz
ID1: T ID2: - ID3: 490kHz
ID1: - ID2: - ID3: 4209.5kHz ID1: A ID2: - ID3: Range
55nm
Save data ?
Edit window (Ex. NAVTEX station Oostende)
8. Edit data as appropriate.
9. Confirm that Save station? is chosen, and then press the ENT key.
10. Press ◄ to choose “YES”, and then press the ENT key to erase the edit
window.
11. Press the MENU/ESC key several times to close the menu.
Deleting NAVTEX stations
You may delete unnecessary NAVTEX stations as follows:
1.
2.
3.
4.
5.
Press the MENU/ESC key to show the main menu.
Press ▲ or ▼ to choose Service, and then press the ENT key.
Press ▲ or ▼ to choose Edit Station List, and then press the ENT key.
Press ◄ or ► to choose the NAV area to be deleted. (01 to 06, EXT).
Press the LIST key to choose the frequency to be deleted (518kHz, 490kHz
or 4209.5kHz).
6. Press ▲ or ▼ to choose the station name to be deleted, and then press ENT
key.
The item window appears.
2-13
2. OPERATION
Edit
Delete
7. Press ▲ or ▼ to choose Delete, and then press the ENT key.
The message “Delete station?” appears.
8. Press ◄ to choose “Yes”, and then press the ENT key to close the edit
window.
9. Press the MENU/ESC key several times to close the menu.
2.14
Icons
The NX-700 shows various icons to denote equipment status, and these are as
shown in the table below.
Icon
Status
Meaning
Status icon (shown at the tip of display)
Blinking
L1
L2
Blinking
Blinking
Blinking
L1
Blinking
L2
Blinking
Shows that a Local frequency message has not
been read.
L1: 490 kHz, L2: 4209.5 kHz
Appears while receiving a message.
I: International frequency (518 kHz)
L1: 490 kHz
L2: 4209.5 kHz
Lighting
Displayed when the voltage of the internal battery is
low. The message Printer error” also appears on the
display.
Lighting
Print error (no paper, not connected to the printer,
etc.). The message “Printer error” also appears on
the display.
Lighting
While printing.
Shows that an International frequency (518 kHz)
message has not been read.
Message icon (shown next to messages)
Lighting
Displayed when message is displayed for the first
time.
(This icon disappeared after 24 hours has passed.)
Lighting
Displayed when message type D (SAR) is displayed.
Lighting
Appears when message type A, B or L (Warning) is
displayed.
Lighting
Protected message
NEW
SAR
!!
2-14
2. OPERATION
2.15
Messages List
In addition to the message “Received new local (int’l) msg.” the following
message-related messages may appear on the display.
Message
New message received.
Oldest message deleted to
free up memory.
Same message with lower
error rate received.
Currently displayed
message will be deleted.
Term of validity expired.
Currently displayed
message will be deleted.
Message not chosen for
display received; it is a int’l
00 message. Choose “All
Message”(LIST menu) to
display.
Meaning
Appears when the oldest
message is deleted to
make space for the latest
one.
Appears when two
messages have the
same ID are received
and the latter’s error rate
is lower than the former.
Appears when 66 hours
has passed after
receiving the currently
displayed message.
Appears when receiving
an international message
not specified for display
(00).
Message not chosen for
display received; it is a
local 00 message. Choose
“All Message”(LIST menu)
to display.
Appears when receiving
a local message not
specified for display (00).
Int’l message not chosen
for display received.
Choose “All
Message”(LIST menu) to
display.
Appears when receiving
an international message
not specified for display
(Normal).
Local message not chosen
for display received.
Choose “All
Message”(LIST menu) to
display.
Appears when receiving
a local message not
specified for display
(Normal).
Remedy
Press any key.
Press any key.
Press any key.
Press any key, and then
choose All Message in
the List window.
2-15
2. OPERATION
2.16
Other Functions
This paragraph describes the various options which allow you to set up your unit
to suit your needs.
NAVTEX menu
Item
Receive
Mode
Local
Channel
Auto Print
Description
Chooses the receiving mode. (See
paragraph 2.6.)
Chooses the local channel.
Chooses the message to print
automatically. (See paragraph 2.12.)
Rcv Station & Receives messages in the category.
Msg
User Select
Sets the station and type of message to
Station &
be shown on the SELECT MESSAGES
Msg
display.
Setting
INS, Auto, Manual
490kHz, 4209.5kHz
Off, All, User Select
System menu
Item
Description
Turns the audible alarm on/off when receiving a
Warn Msg Alm
Warning message (A, B, and L).
Turns monitoring of Rx signal on/off.
Off: Disables monitoring.
Signal Monitor
Int’l: Monitors international frequency.
Local: Monitors local frequency.
Key Beep
Turns key beep on/off.
If a GPS receiver feeds nav data to the NAVTEX.
You may use local time instead of UTC time.
Time Offset
Enter the time difference between local time and
UTC time.
Units
Printer
2-16
Setting
On, Off
Off, Int’l, Local
On, Off
-13:30 to
+13:30
nm, kt,
Chooses units of measurement (distance and
km, km/h,
ship speed) to be shown on the User Display.
mi, mi/h
None,
Sets the printer type. (See paragraph 4.6.)
External,
Internal
2. OPERATION
Display menu
Item
Scrolling
Description
Selects the speed of scrolling by pressing ▲ or ▼.
Slow: Scrolls by one line.
Fast: Scrolls by half of screen.
Skips to $$:
Scrolls line by line in list display; Skips to $$ position in detailed
display.
Font Size
Selects the size of characters.
Time Display
Selects the time format.
Setting
Slow, Fast,
Skip to $$
Small,
Medium,
Large
24 hour,
12 hour
Selects the date format.
MMM DD YYY,
Date Display
DD MMM YYYY,
YYYY MMM DD
Selects the type of data as user display to be shown at the
bottom of the display.
Nav Data
Date
Own ship's
position
Ship's speed
MAY 07 2005
00:00:18
12 34. 001 ' N
123 45. 001 ' E
SOG 1. 6 kt
COG 56. 9
Course
[ ][ ] SCROLL
[ ][ ] CHANGE FREQ
[MENU] MENU
[ENT] SHOW MESSAGE
[LIST] LIST MENU [PRINT] PRINT MENU
User Display
Off,
Nav Data,
Distance
Distance
Distance between the positions shown in the message and own ship's.
DISTANCE
23.4nm
[ ][ ] SCROLL
[ ][ ] CHANGE FREQ
[MENU] MENU
[ENT] SHOW MESSAGE
[LIST] LIST MENU [PRINT] PRINT MENU
Speed
Display
Contrast
Selects the speed format to be displayed.
SOG: Speed Over Ground
STW: Speed Through Water
Sets the display contrast.
SOG, STW
0 to 9
2-17
2. OPERATION
Service menu
Item
Description
INS Input
Speed
Selects the speed at which to input data from INS..
INS Output
Speed
Print Header
Edit Station
List
Default
Settings
Test
Selects the speed to output data to the INS.
Turns the header (Own ship’s position and date
when receiving a message) for printing on/off.
Edits/deletes stations. (See paragraph 2.13.)
Restores all default settings. (See paragraph 3.5.)
Starts the diagnostic test. (See paragraph 3.4.)
Shows the status for International and Local
receiving.
Setting
4800, 9600,
19200,
38400 bps
4800, 9600,
19200,
38400 bps
On, Off
International
message
Rcv Monitor
2-18
Local message
3.
MAINTENANCE &
TROUBLESHOOTING
This chapter provides information necessary for keeping your unit in good
working order and remedying simple problems.
WARNING
Do not open the equipment.
Hazardous voltage which can
cause electrical shock exists
inside the equipment. Only
qualified personnel should
work inside the equipment.
3.1
Maintenance
Regular maintenance is important for optimum performance. A maintenance
program should be established and should at least include the items shown in
the table below.
Maintenance program
Item
Check point
Remedy
Display unit connectors
Check for tight connection.
Tighten loosened connectors.
LCD
The LCD will, in time,
accumulate a coating of dust
which tends to dim the picture.
Wipe LCD lightly with soft
cloth to remove dust.
Wipe the LCD carefully to
prevent scratching, using
tissue paper and an LCD
cleaner. To remove dirt or salt
deposits, use an LCD cleaner,
wiping slowly with tissue
paper so as to dissolve the dirt
or salt. Change paper
frequently so the salt or dirt
will not scratch the LCD. Do
not use solvents such as
thinner, acetone or benzene
for cleaning.
Ground terminal
Check for tight connection and Clean or replace ground wire
corrosion.
as necessary.
3-1
3. MAINTENANCE & TROUBLESHOOTING
3.2
Replacement of Fuse, Battery and Thermal
Paper
Fuse
The fuse inside the receiver unit protects the equipment from overcurrent and
reverse polarity. If the fuse blows, contact your dealer about replacement.
Name
Fuse
Type
FGMB 2A 125V
Code No.
000-103-165
WARNING
Use the proper fuse.
Use of a wrong fuse can result in damage
to the equipment or cause fire.
Battery
A battery is installed on the circuit board inside the display unit, and it preserves
data when the power is turned off. The life of the battery is about 5-10 years, and
its voltage is checked when the power is turned on. When its voltage is low, the
BATT icon appears on the display to alert you. When this happens, contact your
dealer to request replacement of the battery.
Note: When the battery is dead, all default settings are restored.
Name
BATT
Type
Code No.
CR2450-F2ST2L 000-144-941
WARNING
Ensure battery polarity is correct.
Wrong polarity may cause the batteries to
explode.
3-2
3. MAINTENANCE & TROUBLESHOOTING
Thermal paper (NX-700A only)
When the thermal paper runs out completely, the X icon appears at the
right-hand top corner on the display. Replace the paper as follows.
Name
Thermal paper
Type
TP058-30CL
Code No.
000-154-047
1. Turn off the power.
2. Press the button shown below to open the paper holder cover.
Eject button
3. Peel the tape from the end of new paper.
Tape
4. Set the new paper in the paper container in the direction shown below.
Paper holder
New paper
Paper holder cover
5. Pull the end of the paper by 2 to 3 cm (as shown above), and then close the
cover.
3-3
3. MAINTENANCE & TROUBLESHOOTING
3.3
Troubleshooting
This section provides simple troubleshooting procedures which the user can
follow to restore normal operation. If you cannot restore normal operation do not
attempt to check inside the unit. Any trouble should be referred to a qualified
technician.
If . . .
then . . .
- check for blown fuse.
you cannot turn on the power
- check battery for proper voltage
output.
the equipment receives unwanted
confirm that “Manual” is chosen at
messages.
Receive Mode on the NAVTEX menu.
check equipment by the diagnostic
test.
check the broadcasting schedule.
NAVTEX signal cannot be received.
check that the D-sub connector is
firmly fastened.
check that the antenna cable is firmly
fastened.
paper does not advance. (NX-700A only)
load paper correctly.
paper feeds but no recording. (NX-700A
check if correct thermal paper is being
only)
used.
keep the paper in a well-ventilated and
paper has darkened. (NX-700A only)
cool place.
check the setting of Printer on the
System menu.
check the printer cable.
the recording is not proper for the external
check that the power of printer is
printer. (NX-700B only)
turned on and status is
“SELET/READY”.
check that paper is set properly.
3-4
3. MAINTENANCE & TROUBLESHOOTING
3.4
Diagnostics
The memory test checks ROM, RAM, data port, battery, keyboard and LCD for
proper operation and displays program version numbers.
1. Press the MENU/ESC key to open the main menu.
2. Press ▼ to choose Service, and then press the ENT key.
3. Press ▲ or ▼ to choose Test, and then press the ENT key.
The message “Start test?” appears.
4. Press ◄ to choose “Yes”, and then press the ENT key.
Memory Test
Program No
Boot
ROM
SRAM
DRAM
CPU RAM
EEPROM
Battery
: 0850192-01.*
: 0850193-01.*
: OK
: OK
: OK
: OK
: OK
: OK (3.2V)
Hit any key.
*: Program version no.
Memory test
For any NG (No Good), contact your dealer.
5. When the message “Hit any key.” appears at the bottom of screen, press any
key (except
key) to show the key test screen.
Key Test
If there is no operation for
10 s, the screen changes.
Key test
6. Press each key (except
key) one by one.
A key is functioning properly if its on-screen location fills in black when the key is
pressed.
7. After all keys have been tested or no key is pressed after 10 seconds, the
equipment starts the LCD test by showing the white and black display (level
0 to 9).
3-5
3. MAINTENANCE & TROUBLESHOOTING
8. When the message “Hit any key” appears on the screen, press any key
(except
key) to show the Rx test screen.
The alarm sounds while the Rx test is being conducted. Also the test message is
printed when the item other than “None” at Printer on System menu.
Rx test
9. When the message “Hit any key.” appears on the screen, press any key
key) or wait for one minute with no operation to finish.
(except
10. Press the MENU/ESC key several times to close the menu.
3.5
Restoring All Default Settings
This operation restores all default settings. The following two settings, however,
are not disturbed.
-Received messages
-NAVTEX stations list (See paragraph 2.13.)
1. Press the MENU/ESC key to show the main menu.
2. Press ▼ to choose Service, and then press the ENT key.
3. Press ▲ or ▼ to choose Default Setting, and then press ENT key.
The message “Restore default settings?” appears.
4. Press ◄ to choose “Yes”, and then press the ENT key.
The Service menu appears.
5. Press the MENU/ESC key several times to close the menu.
3-6
4.
INSTALLATION
4.1
Display Unit
The display unit can be installed on a tabletop, on the overhead, or in a panel.
Refer to the outline drawings at the back of this manual for installation
instructions. When selecting a mounting location, keep in mind the following
points.
• Locate the unit away from exhaust pipes and vents.
• Locate it of direct sunlight, (or in a suitable, ventilated enclosure) to prevent
heat which can build up inside the cabinet.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Allow sufficient maintenance space at the sides and rear of the unit and leave
sufficient slack in cables, to facilitate maintenance and servicing.
Tabletop, overhead mounting
1. Fix the hanger by using four self-tapping screws (5x20).
2. Screw knob bolts in display unit, set it to the hanger, and tighten the knob
bolts.
Note: For the overhead mounting, reinforce the mounting location and secure
the hanger, with bolts, nuts and washers (local supply).
NX-700A
NX-700B
4-1
4. INSTALLATION
Flush mounting
The display unit can be installed flush mounted in a console or panel by using
the optional flush mount kit.
(For NX-700A)
Type: OP08-19
Code No.: 004-514-810
Name
Type
Code No.
Qty Remarks
Mounting metal
08-023-1019 100-326-960
Self-tapping screw
5X20
000-802-081
Hex. bolt
M8x15
000-862-144
Spring washer
M8
000-864-262
1. Cut out a hole with dimensions as shown below in the mounting location.
156+1
30+1
168+0.5
284+0.5
275+1
2. Attach the fixing metal to the display unit with two hex. bolts (M8x15,
supplied with optional kit) and spring washers (supplied with optional kit).
3. Fasten six self-tapping screws to fix the display unit to the mounting location.
144+1
155+0.5
(For NX-700B)
Type: OP08-20
Code No.: 004-514-820
Name
Type
Code No.
Qty
Remarks
Mounting metal
08-023-2011 100-327-010 1
Self-tapping screw 5x20
000-802-081 4
Pan head screw
M4x12
000-802-130 4
1. Cut out a hole with dimensions as shown below in the mounting location.
156+1
155+0.5
2. Attach the fixing metal to the display unit with four pan head screws (M4X12,
supplied with the optional kit).
3. Fasten four self-tapping screws (supplied with the optional kit) to fix the
display unit to the mounting location.
4-2
4. INSTALLATION
Receiver Unit
General mounting considerations
• The mounting location should be well ventilated and dry.
• The unit can be mounted on bulkhead or the desk.
• Secure the maintenance space shown in drawing at the back of this manual
for ease of maintenance and service.
Mounting Method
Fasten the receiver unit with four self-tapping screws (5x20, supplied as
installation material). For bulkhead mounting, tighten upper self-tapping screws
so there is 5 mm clearance between bottom of screw head and bulkhead. Then,
hook the receiver unit on the upper screws. Tighten upper screws followed by
the lower screws.
210+1
205+1
Fixing hole 2- 6
4.2
210+1
4-3
4. INSTALLATION
4.3
Antenna Unit
Mounting considerations
Install the antenna unit referring to the antenna installation diagram at the back
of this manual. When selecting a mounting location for the antenna unit, keep in
mind the following points:
• Do not shorten the antenna cable.
• The NX-700 contains a very sensitive receiver. To avoid mutual interface with
other radio equipment, do not install this unit near an SSB/VHF/CB
radiotelephone.
• When fixing the antenna cable to the mast with the cable tie, wrap the vinyl
sheet between the cable and mast to protect the cable from injury.
Vinyl sheet
(Local supply)
4.4
Cable tie
(Local supply)
Printer (NX-700B only)
Prepare the printer by locally as shown below for the NX-700B.
-Serial printer
-Baud Rate: 9600 bps
-Character length: 8 bit
-Parity: No
-X control: XON/XOFF
-32 characters/line or more
4-4
4. INSTALLATION
4.5
Wiring
Antenna unit
NX-7H
Display unit
NX-700A or B
Antenna cable
04S4168 10/20/30/40/50 m
DSUB25P-DSUB25P cable
(3 m)
Receiver unit
NX-7001
Ground cable
(Local supply)
-INS
-Printer (for NX-700B only)
-Alarm
Power cable
(Local supply)
12-24 VDC
4-5
4. INSTALLATION
Receiver unit
All cables are gathered to the receiver unit. Connect cables at inside of the
receiver unit as shown below.
RCV Board
08P3227
TB401 TB402
(+) (-)
J402
J403
Antenna cable
(to Antenna unit)
DPYC-2.5
(to 12-24 VDC)
TTYCS-1Q
(to INS)
Printer cable
(to Printer, NX-700B only)
DPYC-1.5
(to External alarm)
DSUB25P-DSUB25P-3M cable
(to Display unit)
Receiver unit, inside view
Use the following JIS cable (Japan Industrial Standard) or equivalent to connect
power source, INS and external alarm appropriately.
-Power source: DPYC-2.5
-INS: TTYSC-1Q
-External alarm: DPYC-1.5
DPYC-2.5
DPYC-1.5
Armor
Armor
Sheath
Sheath
TTYCS-1Q (Four core twisted)
Armor
Sheath
φ = 12.5 mm
Conductor
S = 2.5 mm 2
φ = 2.01 mm
φ = 11.7 mm
Conductor
S = 1.5 mm 2
φ = 1.56 mm
For printer, use the cable supplied with the printer.
4-6
Shield
φ = 11.3 mm
Conductor
S = 0.75 mm2
φ = 1.11 mm
4. INSTALLATION
Fabricate these cables as below to connect to the receiver unit.
5 mm
100 mm
How to use J402 and 403 connector
1. Insert the terminal opener in connector.
2. Insert a wire in terminal while pressing and holding the terminal opener.
3. Release the terminal opener. Pull wire to confirm firmly set it is in terminal
board.
Terminal opener
Wire
Antenna cable
Be sure to leave some slack in the cable for future service and maintenance.
For RG-10/U-Y cable
When using the coaxial cable, type RG-10/U-Y (or equivalent), attach the
FM-MP-7 connector (supplied as installation material) as below.
1.
2.
3.
4.
5.
Remove the sheath by 30 mm.
Bare 23 mm of the center conductor. Trim braided shield by 5 mm and tin.
Slide coupling ring onto cable.
Screw the plug assembly on the cable.
Solder plug assembly to braided shield through solder holes. Solder contact
sleeve to conductor.
6. Screw coupling ring into plug assembly.
30 mm
Sheath
5 mm
Plug assembly
Contact sleeve
2 mm
Solder here.
Conductor
Braided shield
Insulator
Coupling ring
Solder both
sides of hole.
Cut conductor here.
4-7
4. INSTALLATION
Extending antenna cable length
When connecting two cables for extension, use optional extension cable kit
OP-04-2.
Code No.: 000-041-174 (10 m), 000-041-175 (20 m), 000-041-176 (30 m),
000-041-177 (40 m), 000-041-178 (50 m)
Name
Type
Cable assy
04S4168
M-A-JJ
FMA-1
Insulating tape U tape 0.5x19x5M
Connector
Code No.
005-948-320
005-948-330
005-948-340
005-948-350
005-948-360
000-101-287
000-152-964
000-800-985
Qty
Remarks
10 m
20 m
30 m
40 m
50 m
One of these
is contained.
OP04-2
To Receiver unit
M-A-JJ or FMA-1 connector
Grounding
The ground wire (local supply) should be 1.25 sq or larger. The ground wire
should be as short as possible.
4-8
4. INSTALLATION
4.6
Setting of Printer
After the connection completely, the setting of printer should be done for
NX-700B as shown below. (For NX-700A, use the default setting as is.)
key to turn the power on.
1. Press the
2. Press the MENU key to show the main menu.
Menu
NAVTEX
System
Display
Service
3. Press ▼ to choose System, and then press the ENT key or ► to activate the
System menu.
System
Warn Msg Alm
Signal Monitor
Key Beep
Time Offset
Units
Printer
Off
Off
Off
+00:00
nm, kt
NX-700A
4. Press ▼ to choose Printer, and then press the ENT key or ► to show the
item window.
None
NX-700A
Upright
Inverted
5. Press ▲ or ▼ to choose the appropriate setting, and then press the ENT
key.
NX-700A: For NX-700A only.
Upright: When NX-700B is connected with the upright type printer which ejects
the paper from bottom to top direction.
Inverted: When NX-700B is connected with the wall-hung type printer which
ejects the paper from top to bottom direction.
6. Press the MENU key several times to close the menu.
4-9
4. INSTALLATION
4.7
Interfacing
This equipment can receive navigation data in IEC 61162-1 Ed2/2 format.
Priority
TIME＆DATE
L/L
SOG
STW
COG
ZDA
GNS > GGA > RMC > GLL
VTG > VBW > RMC
VHW > VBW
VTG > RMC
Input data sentence description
GGA: GPS position fixing condition
$--GGA,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,x,xx,x.x,x.x,M,x.x,M,x.x,xxxx*hh
| |
| | | | | | | | |
| |
| |
| | | | | | | | |
| +-- 11
| |
| | | | | | | | | +---- 10
| |
| | | | | | | | +--------- 9
| |
| | | | | | +---+------------ 8
| |
| | | | +---+------------------ 7
| |
| | | +------------------------- 6
| |
| | +---------------------------- 5
| |
| +------------------------------- 4
| |
+----+--------------------------------- 3
+---+--------------------------------------------- 2
+------------------------------------------------------------- 1
1. UTC of position
2. Latitude, N/S
3. Longitude, E/W
4. GPS quality indicator (see note)
5. Number of satllite in use,00-12, may be different from the number in view
6. Horizontal dilution of precision
7. Antenna altitude above/below mean sealevel, m
8. Geoidal separation, m
9. Age of differential GPS data
10. Differential reference station ID, 0000-1023
11. Checksum
NOTE
0 = fix not available or invalid
1 = GPS SPS mode, fix valid
2 = differential GPS, SPS mode, fix valid
3 = GPS PPS mode, fix valid
4 = Real Time Kinetic. Satellite system used in RTK mode with fixed integers
5 = Float RTK. Satellite system used in RTK mode with floating fingers
6 = Estimated (dead reckoning) mode
7 = Manual input mode
8 = Simulator mode
The GPS quality indicator shall not be a null field.
4-10
4. INSTALLATION
GLL: Latitude and longitude
$--GLL,llll.lll,a,yyyyy.yyy,a,hhmmss.ss,A,a*hh
| |
| | |
| |
| | +------- 6
| |
| +--------- 5
| |
+----------- 4
| |
+---------------- 3
| |
+------+----------------------- 2
+---+----------------------------------- 1
1. Latitude, N/S
2. Longitude, E/W
3. UTC of position
4. Status: A=data valid, V=data invalid
5. Mode indicator(see note)
6. Checksum
NOTE Positioning system Mode indicator:
A = Autonomous
D = Differential
E = Estimated (dead reckoning)
M = Manual input
S = Simulator
N = Data not valid
The Mode indicator field supplements the Status field. The Status field shall be
set to V=invalid for all values of Operating Mode except for A=Autonomous and
D=Differential. The positioning system Mode indicator and Status field shall not
be null fields.
4-11
4. INSTALLATION
RMC: Recommend Minimum Specific GNSS Data
$--RMC,hhmmss.ss,A,llll.lll,a,yyyyy.yyy,a,x.x,x.x,xxxxxx,x.x,a,a*hh
| | |
| | |
| | | |
| | |
| | |
| | | +--- 10
| | |
| | |
| | +----- 9
| | |
| | |
+--+------- 8
| | |
| | |
+--------------- 7
| | |
| | +--------------------- 6
| | |
| +------------------------- 5
| | |
+---+---------------------------- 4
| +---+---------------------------------------- 3
+--------------------------------------------------- 2
+---------------------------------------------------------- 1
1. UTC of position fix
2. Status: A=data valid, V=navigation receiver warning
3. Latitude, N/S
4. Longitude, E/W
5. Speed over ground, knots
6. Course over ground, degrees true
7. Date: dd/mm/yy
8. Magnetic variation, degrees E/W
9. Mode indicator(see note)
10. Checksum
NOTE Positioning system Mode indicator:
A = Autonomous
D = Differential
E = Estimated (dead reckoning)
M = Manual input
S = Simulator
N = Data not valid
The Mode indicator field supplements the Status field. The Status field
shall be set to V=invalid for all values of Operating Mode except for
A=Autonomous and D=Differential. The positioning system Mode indicator
and Status field shall not be null fields.
4-12
4. INSTALLATION
ZDA: Time and date
$--ZDA,hhmmss.ss,xx,xx,xxxx,xx,xx*hh
| |
| | | |
| |
| | | +--------- 7
| |
| | +----------- 6
| |
| +-------------- 5
| | +------------------ 4
| +---------------------- 3
+------------------------- 2
+--------------------------------- 1
1. UTC
2. Day, 01 to 31(UTC)
3. Month, 01 to 12(UTC)
4. Year(UTC)
5. Local zone hours, 00h to +-13h
6. Local zone minutes, 00 to +59
as local hours
7. Checksum
4-13
4. INSTALLATION
NRQ: Request NAVTEX messages
Command to request specific NAVTEX message(s) to be sent to IBS port. Messages may be
sent in any order. Each message sent from the IBS port shall be preceded by the NRX sentence.
$-NRQ,x,h,h*hh
Note 1: the transmitter coverage area mask is defined as a 32 bit mask 0xFF.FF.FF.FF where
the least significant bit represents transmitter coverage area ’A’, the next bit is ’B’ and so on up
to bit 25 which is ’Z’. Bits 31-26 shall be set to ’0’. To select a transmitter coverage area its
corresponding bit shall be set to ’1’; to deselect a transmitter coverage area its corresponding
bit shall be set to ’0’.
Note 2: the message type mask is defined as a 32 bit mask 0xFF.FF.FF.FF where the least
significant bit represents message type ’A’, the next bit is ’B’ and so on up to bit 25 which is ’Z’.
Bits 31-26 shall be set to ’0’. To select a message type its corresponding bit shall be set to ’1’;
to deselect a message type its corresponding bit shall be set to ’0’.
NMK: Set NAVTEX mask
Command to set B1.B2 mask for specific NAVTEX message(s) to be stored in internal message
memory & echoed to the IBS port.
$-NMK,x,h,h*hh
Note 1: the transmitter coverage area mask is defined as a 32 bit mask 0xFF.FF.FF.FF where
the least significant bit represents transmitter coverage area ’A’, the next bit is ’B’ and so on up
to bit 25 which is ’Z’. Bits 31-26 shall be set to ’0’. To select a transmitter coverage area its
corresponding bit shall be set to ’1’; to deselect a transmitter coverage area its corresponding
bit shall be set to ’0’.
Note 2: the message type mask is defined as a 32 bit mask 0xFF.FF.FF.FF where the least
significant bit represents message type ’A’, the next bit is ’B’ and so on up to bit 25 which is ’Z’.
Bits 31-26 shall be set to ’0’. To select a message type its corresponding bit shall be set to ’1’;
to deselect a message type its corresponding bit shall be set to ’0’.
Example usage:
&NVNMK,518,00001E1F,00000023*42
4-14
4. INSTALLATION
ACK: Acknowledge
$--ACK,xxx*hh
| |
| + ------------------------2
+-----------------------------1
1. Local alarm number(identifier)
2. Checksum
GNS:
$--GNS,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,c--c,xx,x.x,x.x,x.x,x.x,x.x*hh
| | | | | | | | | | | |
| | | | | | | | | | | +--- 11
| | | | | | | | | | +------ 10
| | | | | | | | | +---------- 9
| | | | | | | | +-------------- 8
| | | | | | | +------------------ 7
| | | | | | +---------------------- 6
| | | | | +------------------------- 5
| | | | +------------------------------ 4
| | +-----+--------------------------------- 3
+-----+--------------------------------------------- 2
+------------------------------------------------------------- 1
1. UTC of position
2. Latitude, N/S
3. Longitude, E/W
4. Mode indicator
5. Total number of satllite in use,00-99
6. HDOP
7. Antenna altitude, metres, re:mean-sea-level(geoid)
8. Geoidal separation
9. Age of differential data
10. Differential reference station ID
11. Checksum
4-15
4. INSTALLATION
VHW: Water speed and heading
$--VHW,x.x,T,x.x,M,x.x,N,x.x,K*hh
| | | | | | | | |
| | | | | | | | +--------- 5
| | | | | | +--+----------- 4
| | | | +--+----------------- 3
| | +---+----------------------- 2
+---+----------------------------- 1
1. Heading, degrees true
2. Heading, degrees magnetic
3. Speed, knots
4. Speed, km/h
5. Checksum
VTG: Course over ground and ground speed
$--VTG,x.x,T,x.x,M,x.x,N,x.x,K,a*hh
| | | | | | | | | |
| | | | | | | | | +------- 6
| | | | | | | | +--------- 5
| | | | | | +--+----------- 4
| | | | +--+----------------- 3
| | +--+----------------------- 2
+--+----------------------------- 1
1. Course over ground, degrees true
2. Course over ground, degrees magnetic
3. Speed over ground, knots
4. Speed over ground, km/h
5. Mode indicator(see note)
6. Checksum
NOTE Positioning system Mode indicator:
A = Autonomous
D = Differential
E = Estimated (dead reckoning)
M = Manual input
S = Simulator
N = Data not valid
The positioning system Mode indicator field shall not be a null field.
4-16
4. INSTALLATION
VBW: Dual ground/water speed
$--VBW,x.x,x.x,A,x.x,x.x,A,x.x,A,x.x,A*hh
| | | | | | | | | | |
| | | | | | | | | | +--- 11
| | | | | | | | | +----- 10
| | | | | | | | +-------- 9
| | | | | | | +----------- 8
| | | | | | +-------------- 7
| | | | | +----------------- 6
| | | | +-------------------- 5
| | | +------------------------ 4
| | +--------------------------- 3
| +------------------------------ 2
+---------------------------------- 1
1. Longitudial water speed, knots
2. Transverse water speed, knots
3. Status: water speed, A=data valid V=data invalid
4. Longitudial ground speed, knots
5. Transverse ground speed, knots
6. Status: ground speed, A=data valid V=data invalid
7. Stern transverse water speed, knots
8. Status: stern water speed, A=data valid V=data invalid
9. Stern transverse ground speed, knots
10. Status: stern ground speed, A=data valid V=data invalid
11. Checksum
4-17
4. INSTALLATION
Output data description
NRX: New NAVTEX received message
New NAVTEX message to follow in ASCII format
$NXNRX,xxxx,x,x,x,xx,xx,xxxx,hhmmss,x.x,n--n*hh
encapsulated message
error rate % (xx.x)
UTC of receipt of message
year
month (1-12)
day (0-31)
freq ('490', '518' or '4209')
number of lines in message (1 to 999)
line number (1 to 999)
message identifier (B1B2B3B4)
The first NRX sentence transmitted for a particular NAVTEX message shall contain valid data
for all fields. For subsequent NRX sentences encapsulating a NAVTEX message, all fields apart
from 'message identifier', 'line number' and 'encapsulated message' are optional. If UTC time or
date are not known then the fields are NULL.
Example usage:
$NXNRX,TA21,1,4,518,10,01,2005,102000,2.2,291600 UTC JAN =*hh
$NXNRX,TA21,2,4,,,,,,,OOSTENDERADIO - INFO 37/04 =*hh
$NXNRX,TA21,3,4,,,,,,,WESTHINDER ANCHORAGE, ANCHOR LOST IN*hh
$NXNRX,TA21,4,4,,,,,,,POSITION 51-24.94N 002-40.02E.+*hh
Example usage when no UTC is available to the equipment:
$NXNRX,TA21,1,4,518,,,,,2.2, TEST MESSAGE*hh
Where the NAVTEX message contains reserved characters as defined in IEC 61162-1, then
these shall be handled by using ASCII 'escape code' :
c) Reserved character
d) 
e) 
f) $
^24
g) *
^2A
h) ,
^2C
i) !
^21
j) \
^5C
k) ^
^5E
l) ~
^7E
4-18
ASCII escape code
^0D
^0A
4. INSTALLATION
ALR: Set alarms
$NXALR,hhmmss.ss,xxx,A,A,c--c*hh
| | | | |
| | | | +----------------- 6
| | | +----------------- 5
| | +-------------------- 4
| +---------------------- 3
+------------------------- 2
+--------------------------------- 1
1. Time of alarm condition change, UTC
2. Local alarm number(identifier)
3. Alarm condition(A=threshold exceeded, V=not exceeded)
4. Alarm's acknowledge state, A=acknowledged V=unacknowledged
5. Alarm's description text
6. Checksum
Serial Interface
4-19
MENU TREE
MENU/ESC Key
LIST key
PRINT key
NAVTEX
Receive Mode (INS, Auto, Manual)
Local Channel (490kHz, 4209.5kHz)
Auto Print (Off, All, User Select)
Rcv Station & Msg
User Select Station & Msg
System
Warn Msg Alm (Off, On)
Signal Monitor (Off, Int’l, Local)
Key Beep (Off, On)
Time Offset (-13:30 to +13:30, 0:00)
Units (nm, kt, km, km/h, mi, mi/h)
Printer (None, NX-700A, Upright, Inverted)
Display
Scrolling (Slow, Fast, Skip To $$)
Font Size (Small, Medium, Large)
Time Display (24hour, 12hour)
Date Display (MMM DD YYYY, DD MMM YYYY, YYYY MMM DD)
User Display (Off, Nav Data, Distance)
Speed Display (SOG, STW)
Contrast (0 to 9, 5)
Service
INS Input Speed (4800, 9600, 19200, 38400bps)
INS Output Speed (4800, 9600, 19200, 38400bps)
Print Header (Off, On)
Edit Station List
Default Setting
Test
Rcv Monitor
All Messages
Alarm Messages
User Selected Messages
Good Messages
Lock Message
Print
Cancel Print
AP-1
FURUNO
NX-700
SPECIFICATIONS OF NAVTEX RECEIVER
NX-700
NAVTEX RECEIVER
1.1
Receiving frequency
518 kHz and 490 kHz or 4209.5 kHz
1.2
Mode of reception
F1B
1.3
Sensitivity
2 µV e.m.f. (50 ohms), 4% error rate or less
1.4
Input protection
Withstands 30Vrms for 15 min or more (w/ pre-amp unit)
1.5
Spurious emission
1nW or less
1.6
Message category
A: Navigation warning
B: Meteorological warning
C: Ice report
D: Search and rescue information/ piracy and armed robbery
E: Meteorological forecast
F: Pilot message
G: Decca message
H: Loran-C message
I: Omega message
J: Differential omega message
K: Other electronic navigational aid and system message
L: Navigational warning (additional)
M to Y: Reserved – presently not used
V: Notice to Fishermen (US only)
Z: QRU (no message on hand)
DISPLAY SECTION
2.1
Display system
5-inch, 76 (W) x 100 (H) mm, monochrome LCD, 240 x 320 dots
2.2
Display modes
Message selection mode
Message display mode
2.3
ID storage
200 x 2 channels
2.4
Message storage
200 messages x 2 channels
(100,000 characters x 2 channels)
PRINTER SECTION (FOR NX-700A ONLY)
3.1
Printing system
Line thermal head printing system
3.2
Printing paper
Thermal paper (58 mm x 30 m)
3.3
Printing width
48mm
3.4
Character format
24 x 12 dot
3.5
Dot pitch
8 dots/ mm
3.6
Number of characters
32 characters/line
3.7
Print speed
Approx. 20mm/sec.
SP - 1
E5649S01-1
050418
FURUNO
NX-700
ANTENNA UNIT
4.1
Antenna type
NX-7H: H-field antenna for NX-700 with preamp
4.2
Output impedance
50 ohms
4.3
Power supply
+7V to +9V (thru co-ax cable)
INTERFACE
5.1
Input data
IEC61162 or NMEA0183 Ver1.5/2.0,
GGA, GLL, RMC, ZDA, NRQ, NMK, ACK, GNS, VHW, VTG, VBW
Output data
NRX, ALR
5.2
Alarm
Contact closure signal (max. 0.5A, 50V) for SAR alert
POWER SUPPLY
12-24VDC:
TYP 1.2-0.6A, MAX 1.5-0.8A (NX-700A),
TYP 0.6-0.3A, MAX 0.7-0.4A (NX-700B)
ENVIRONMENTAL CONDITION
7.1
Ambient temperature
Antenna unit
-25°C to +70°C
Receiver / Display unit
-15°C to +55°C
7.2
Relative humidity
95% at 40°C (without dew condensation)
7.3
Waterproofing
Antenna unit
IP66
Receiver / Display unit
IP20 (NX-700B: IP25 for front panel)
7.4
Vibration
IEC 60945
COATING COLOR
8.1
Display unit
N3.0
8.2
Receiver unit
N3.0
8.3
Antenna unit
N9.5
SP - 2
E5649S01-1
050418
A-1
ＰＡＣＫＩＮＧ
ＬＩＳＴ
08AW-X-9862 -0
1/1
NX-700A/NX-700A-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-700-A*
指示部
DISPLAY UNIT
000-040-342 **
予備品
SPARE PARTS
SP08-02000
W-58
感熱記録紙
RECORDING PAPER
(*1)
999-999-086
工事材料
INSTALLATION MATERIALS
CP08-01861
工事材料
INSTALLATION MATERIALS
004-514-350
1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
2.(*1)は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。
(*1) THIS CODE CANNOT BE ORDERED.
（略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
08AW-X-9862
A-2
ＰＡＣＫＩＮＧ
ＬＩＳＴ
08AW-X-9860 -0
1/1
NX-700B/NX-700B-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-700B*
指示部
DISPLAY UNIT
000-152-663 **
工事材料
INSTALLATION MATERIALS
5X20 SUS304
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1種
SELF-TAPPING SCREW
000-802-081
1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
（略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
08AW-X-9860
A-3
ＰＡＣＫＩＮＧ
ＬＩＳＴ
08AW-X-9861 -0
1/1
NX-7001-AN-J*/E*,NX-7001-BN-J*/E*
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-7001-*
受信部
RECEIVER UNIT
000-040-345 **
受信部予備品
RECEIVER UNIT SPARE PARTS
SP08-02101
予備品
SPARE PARTS
004-514-370
工事材料
INSTALLATION MATERIALS
CP08-01860
DSUB25P-DSUB25P-3M
ｹｰﾌﾞﾙ組品
CABLE ASSY.
000-152-698
受信部工材
RECEIVER UNIT INSTALLATION MATERIALS
CP08-01863
工事材料
INSTALLATION MATERIALS
004-514-530
図書
DOCUMENT
OS*-56490-*
操作要領書(和)
OPERATOR'S GUIDE
000-152-805 **
OM*-56490-*
取扱説明書(和)
OPERATOR'S MANUAL
000-152-803 **
1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
（略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
08AW-X-9861
A-4
ＰＡＣＫＩＮＧ
ＬＩＳＴ
08AW-X-9859 -0
1/1
NX-7001-AA-J*/E*、NX-7001-BA-J*/E*
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-7001-*
受信部
RECEIVER UNIT
000-040-345 **
受信部予備品
RECEIVER UNIT SPARE PARTS
SP08-02101
予備品
SPARE PARTS
004-514-370
工事材料
INSTALLATION MATERIALS
CP08-01860
DSUB25P-DSUB25P-3M
ｹｰﾌﾞﾙ組品
CABLE ASSY.
000-152-698
受信部工材
RECEIVER UNIT INSTALLATION MATERIALS
CP08-01864
工事材料
INSTALLATION MATERIALS
004-514-540
図書
DOCUMENT
OS*-56490-*
操作要領書(和)
OPERATOR'S GUIDE
000-152-805 **
OM*-56490-*
取扱説明書(和)
OPERATOR'S MANUAL
000-152-803 **
1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
（略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
08AW-X-9859
A-5
ＰＡＣＫＩＮＧ
ＬＩＳＴ
08AW-X-9852 -0
1/1
NX-7H-0-10/-10-HK,NX-7H-0-20/-20-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-7H*
ｱﾝﾃﾅ
ANTENNA
000-040-214 **
工事材料
INSTALLATION MATERIALS
CP08-01810/01820
CP08-01811
工事材料
INSTALLATION MATERIALS
004-514-610
04S4168 *20M*
ｹｰﾌﾞﾙ組品
CABLE ASSY.
(*)
000-107-019
04S4168 *10M*
ｹｰﾌﾞﾙ組品
CABLE ASSY.
(*)
000-106-821
1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
2.(*)印のｹ-ﾌﾞﾙ組品は選択出来ます。
(*) MARKED CABLES ARE SELECTABLE.
（略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
08AW-X-9852
A-6
CODE NO.
004-514-350
TYPE
CP08-01861
08AW-X-9401 -0
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名
称
NAME
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
略
図
OUTLINE
1種
型名／規格
DESCRIPTIONS
数量
Q'TY
用途／備考
REMARKS
5X20 SUS304
SELF-TAPPING SCREW
CODE NO.
000-802-081
08AW-X-9401
（略図の寸法は、参考値です。
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
A-7
CODE NO.
004-514-530
TYPE
CP08-01863
08AW-X-9402 -0
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名
称
NAME
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
略
図
OUTLINE
1種
型名／規格
DESCRIPTIONS
SELF-TAPPING SCREW
REDUCER(L)
CODE NO.
000-108-861
MP-M3A
ｱﾀﾞﾌﾟﾀ
REDUCER(S)
CODE NO.
000-108-860
FM-MP-7
同軸プラグ
000-802-081
MP-M5A
ｱﾀﾞﾌﾟﾀ
用途／備考
REMARKS
5X20 SUS304
CODE NO.
数量
Q'TY
COAX.PLUG
CODE NO.
000-108-859
08AW-X-9402
（略図の寸法は、参考値です。
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
A-8
CODE NO.
004-514-540
TYPE
CP08-01864
08AW-X-9403 -0
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名
称
NAME
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
略
図
OUTLINE
1種
型名／規格
DESCRIPTIONS
用途／備考
REMARKS
5X20 SUS304
SELF-TAPPING SCREW
CODE NO.
000-802-081
FM-MP-7
同軸プラグ
数量
Q'TY
COAX.PLUG
CODE NO.
000-108-859
08AW-X-9403
（略図の寸法は、参考値です。
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
A-9
08AW-X-9407 -0
CODE NO.
1/1
TYPE
工事材料表
NX-700A/B
INSTALLATION MATERIALS
番 号
NO.
名
称
NAME
略
図
OUTLINE
選択
TO BE SELECT
選択
TO BE SELECT
選択
TO BE SELECT
000-107-020
04S4168 *40M*
ｹｰﾌﾞﾙ組品
CABLE ASSY.
CODE NO.
000-107-021
04S4168 *50M*
ｹｰﾌﾞﾙ組品
用途／備考
REMARKS
CABLE ASSY.
CODE NO.
数量
Q'TY
04S4168 *30M*
ｹｰﾌﾞﾙ組品
型名／規格
DESCRIPTIONS
CABLE ASSY.
CODE NO.
000-107-022
08AW-X-9407
（略図の寸法は、参考値です。
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
A-10
CODE NO.
004-514-610
TYPE
CP08-01811
08AW-X-9404 -0
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名
称
NAME
略
図
OUTLINE
Uﾃｰﾌﾟ
絶縁ﾃｰﾌﾟ
型名／規格
DESCRIPTIONS
数量
Q'TY
用途／備考
REMARKS
0.5X19X5M
SELF-BONDING TAPE
CODE NO.
000-800-985
08AW-X-9404
（略図の寸法は、参考値です。
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
A-11
NAME OF
PART
OUTLINE
ﾋｭｰｽﾞ
004-514-370
TYPE
SP08-02101
SPARE PARTS LIST FOR
SHIP NO.
ITEM
NO.
CODE NO.
08AW-X-9301 -0 1/1
BOX NO.
SETS PER
VESSEL
QUANTITY
DWG. NO.
OR
TYPE NO.
REMARKS/CODE NO.
WORKING
PER
SET
PER
VES
SPARE
FGMB 2A 125V
FUSE
000-103-165
MFR'S NAME
FURUNO
ELECTRIC
（略図の寸法は、参考値です。
CO.,LTD.
DWG NO.
DIMENSIONS IN DRAWING
08AW-X-9301
FOR REFERENCE ONLY.）
1/1
D-1
Y. Hatai
D-2
D-3
D-4
Y. Hatai
D-5
D
固定ボルト
FIXING BOLT
アンテナケーブル
ANTENNA CABLE
0°
-5°
33°
-5° - 33°
ANTENNA BASE No.13-QA330
TYPE
コード番号 000-803-239
CODE No.
アンテナ
直型アンテナベース
ベース型式 RIGHT ANGLE ANTENNA BASE
MOUNTING
METHOD
装備方法
INCLINATION
傾斜
000-803-240
No.13-QA310
L-TYPE ANTENNA BASE
L型アンテナベース
0°
32°
65°
32° -
65°
0°
65° 98°
65° -
98°
C)取付ける場所が傾斜しているとき ANTENNA BASE MOUNTING
オプションのアンテナベースを使う。
USE OPTIONAL ANTENNA BASE No.13-QA330/QA310.
CABLE TIE
(LOCAL SUPPLY)
テープを巻く
WIND TAPE
KEEP CABLE ASIDE TO AVOID
INJURY FROM PIPE.
90ﾟ
アンテナベース基部
MOUNTING LOCATION
＊
3 m
1.5 m
3 m
10 cm
30 cm
φ 76
φ61
4-M5 皿穴
COUNTERSUNK
表 １
1 m
DWG. No.
SCALE
APPROVED
CHECKED
1.5 m
THREAD PER 25.4mm (1 INCH): 14
PITCH: 1.8143 mm
THREAD LENGTH: 15.17 mm
PITCH DIAMETER: 24.17 mm
1-14UNS1B
ねじ山数(25.4mmにつき)： 14
ピッチ： 1.8143 mm
オネジ有効長さ： 15.17 mm
オネジ有効径： 24.17 mm
TX ANTENNA(MF/HF)
送信アンテナ(MF/HF)
MAIN MAST
メインマスト
4 m
4 m
NX-700
NX-300
08-021-310G- 1
±10％ MASS W/ 10m CABLE.
0.94 kg 質量は10mケーブルを含む。
C5629-G05- E
1/2
MASS
TAKAHASHI.T
E.MIYOSHI
1. TABLE 1 INDICATES TOLERANCE OF DIMENSIONS.
DRAWN
MAY 16, '05
NOTE
0.5 m
NAVTEX ANTENNA
ナブテックスアンテナ
1 m
１）指定なき寸法公差は表１による。
±３
注記
±２．５
50 ＜ Ｌ ≦ 100
公差(mm)
TOLERANCE
±１．５
TABLE 1
WHIP ANTENNA
ホイップアンテナ(MF/HF)
WHIP ANTENNA
ホイップアンテナ(VHF/UHF)
RX WHIP ANTENNA
受信ホイップアンテナ
100 ＜ Ｌ ≦ 500
寸法区分(mm)
DIMENSIONS
0 ＜ Ｌ ≦ 50
DISTANCE (MIN.)
確保する距離
DIA. OF 'a'
aの直径
*支柱の太さにより変わる。
* DISTANCE DEPENDS ON MAST DIAMETER OF 'a'.
レーダービームに入らないこと
NOT WITHIN RADAR BEAM
5 m NOT WITHIN INMARSAT BEAM
インマルビームに入らないこと
INMARSAT ANTENNA
インマルサットアンテナ
LOOP ANTENNA
ループ・アンテナ
THE FIGURE BELOW SHOWS THE RECOMMENDED SEPARATION DISTANCES
FROM OTHER ANTENNAS TO AVOID MUTUAL INTERFERENCE.
他の機器のアンテナから下の図の距離以上離す。
取付場所
MOUNTING DIMENSIONS OF ANTENNA BASE
注記 1）パイプ(アンテナベース)はアンテナユニットにねじ込んだ後に固定する。
2）アンテナを固定するときはパイプ（アンテナベース）をアンテナにねじ込むこと。
アンテナ側をねじるとコネクタ部やケーブルに無理がかかり、故障の原因となる。
NOTE 1. FASTEN PIPE(ANTENNA BASE) TO ANTENNA UNIT FIRST THEN FIX THEM TO MAST OR HANDRAIL.
2. WHEN FIXING ANTENNA, TURN PIPE OR ANTENNA BASE; NOT THE ANTENNA.
TURNING THE ANTENNA MAY TWIST THE CABLE AND PLACE STRESS ON CONNECTOR.
アンテナベース
ANTENNA BASE
USE HANDRAIL MOUNTING BASE No.13-RC5160
(CODE No.000-806-114, OPTION).
THE DIAMETER OF THE HANDRAIL MAY BE FROM
φ19mm TO φ32mm.
PIPE
WIND TAPE
テープを巻く
コンベックス
(現地手配）
パイプで傷つかないよう
ケーブルを脇へよける。
パイプ
HANDRAIL MOUNTING
コンベックス
(現地手配）
CABLE TIE
(LOCAL SUPPLY)
パーカー
クランプ
HOSE CLAMP
ケーブル固定板
CABLE FIXTURE
USE A PIPE ONLY.
b)パイプのみを使うとき
レール用アンテナベース No.13-RC5160（取付可能レール直径：φ19∼φ32）
(コード番号：000-806-114）
B)スタンションやパルピットにつけるとき
LEAVE SLACK HERE TO RELIEF
STRESS ON CONNECTOR.
115
ANTENNA CABLE
120
アンテナケーブル
MOUNTING BRACKET
取付補助金具
コネクタに力がかからない
よう、余裕を持たせる。
PIPE
パイプ
WIND TAPE
テープを巻く
USE MAST MOUNTING KIT CP20-01111.
173
a)マスト取付金具CP20-01111(工事材料)でマストに固定する。
MAST MOUNTING
173
A)マストへの取付け
NAME
名称
TITLE
ケーブル固定板
CABLE FIXTURE
ANTENNA UNIT
OUTLINE DRAWING
外寸図
NX-3H-D/NX-7H
空中線部
φ156
D-6
45ﾟ
116
C
DPYC-2.5 *1
INS
プリンターに付属のケーブルを使用
*1
プリンター CABLE SUPPLIED WITH PRINTER
PRINTER
（NX-700Bのみ）
(NX-700B ONLY)
NOTE
*1. SHIPYARD SUPPLY.
*2. OPTION.
PE, IV-1.25 *1
保護アース
DC OUT +
DPYC-1.5 *1
TTYCS-1Q *1
+ DC IN
AC IN
AC/DC電源ユニット
AC/DC POWER SUPPLY
UNIT
PR-240-CE *2
外部アラーム
EXT. ALARM
DPYC-2.5 *1
DPYC-1.5 *1
注記
＊１）造船所手配。
＊２）オプション。
24VDC
100-115/
200-230VAC
1φ,50-60Hz
12-24 VDC
J403
ALARM-H
ALARM-C
FG
SD(PRINTER)
RD(PRINTER)
SG
FG
FG
J402
TD-A
TD-B
FG
RD-A
RD-B
GND-ISO
DWG.No. C5649-C01-A
SCALE
APPROVED
NAME
名 称
CHECKED
GND *1
IV-1.25sq.
04S4168
10/20/30/40/50m
DSUB25P-DSUB25-3M,φ9.9, 3m
MP-3
MP-3
TITLE
MASS
B2 RCV 08P3227
J401
SD(PRINTER) 1
SD(PRINTER) 14
TD-A 2
TD-B 15
RD-A 3
RD-B 16
ALARM-H 4
ALARM-C 17
TEST-RD-A 5
TEST-RD-B 18
FRQ-RD-A 6
FRQ-RD-B 19
490-TD-A 7
490-TD-B 20
518-TD-A 8
518-TD-B 21
12V + 9
0V SG 22
0V GND-ISO 10
DC + 23
DC + 11
DC + 24
DC - 12
DC - 25
DC - 13
ANT
RECEIVER
NX-700A/B
指示部
DISPLAY UNIT
INTERCONNECTION DIAGRAM
NAVTEX RECEIVER
相互結線図
NX-700A/B
ナブテックス受信機
1 NC
14 NC
2 TD-A
15 TD-B
3 RD-A
16 RD-B
4 ALARM-H
17 ALARM-C
5 TEST-RD-A
18 TEST-RD-B
6 FRQ-RD-A
19 FRQ-RD-B
7 490-TD-A
20 490-TD-B
8 518-TD-A
21 518-TD-B
9 12V +
22 0V SG
10 0V GND-ISO
23 DC +
11 DC +
24 DC +
12 DC 25 DC 13 DC -
M-A-JJ
MP-3
延長ケーブル *2
MP-3
EXTENSION CABLE
04S4168
10/20/30/40/50m,φ5.5
アンテナケーブル
ANTENNA CABLE
04S4168,10/20/30/40/50m,φ5.5
OR
RG-10U/Y,30/40/50m *2
> 17 kt)
DRAWN
WAGO
WAGO
TB401
(+)
TB402
(-)
NX-7001
受信部
RECEIVER UNIT
0.6m
NX-7H
アンテナ部
ANTENNA UNIT
S-1
The paper used in this manual
is elemental chlorine free.
Your Local Agent/Dealer
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone :
0798-65-2111
Fax
0798-65-4200
All rights reserved.
Printed in Japan
FIRST EDITION :
Z1
Pub. No. OME-56490
( HIMA ) NX-700
0000
MAY.
:Ma. 20, 2005
*00015280400*
*00015280400*
*00015280400*
*OME56490Z00*
*OME56490Z00*
*OME56490Z00*

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 84
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:7330def8-b62f-4d2a-b5ab-0bfe38cec008
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Modify Date                     : 2005:05:20 10:52:27+09:00
Create Date                     : 2005:05:20 09:59:30+09:00
Metadata Date                   : 2005:05:20 10:52:27+09:00
Document ID                     : uuid:17322e23-fd27-4058-b4d7-dafcfd3c16b2
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools