Furuno USA 9ZWRTR076 marine radar User Manual M1713 OME

Furuno USA Inc marine radar M1713 OME

Operators Manual

MARINE RADAR   MODEL 1715
Your Local Agent/DealerYour Local Agent/Dealer9-52 Ashihara-cho,9-52 Ashihara-cho,Nishinomiya, JapanNishinomiya, JapanTelephone :Telephone : 0798-65-21110798-65-2111Telefax :Telefax : 0798-65-42000798-65-4200FIRST EDITION  :FIRST EDITION  :    .   . 00000000Printed in JapanPrinted in JapanAll rights reserved.All rights reserved.PUB.No.PUB.No. OME-35140OME-35140*00014791100**00014791100**00014791100**00014791100*(( )) MODEL1715MODEL1715 * 0 0 0 1 4 7 9 1 1 0 0 ** 0 0 0 1 4 7 9 1 1 0 0 **OME35140Z00**OME35140Z00**OME35140Z00**OME35140Z00** O M E 3 5 1 4 0 Z 0 0 ** O M E 3 5 1 4 0 Z 0 0 *
  iTABLE OF CONTENTS SAFETY INSTRUCTIONS............................ ii FOREWORD............................................... iii    SYSTEM CONFIGURATION....................... iv EQUIPMENT LISTS..................................... v 1. OPERATION ........................................... 1 1.1 Controls .................................................. 1 1.2 Indications .............................................. 2 1.3 Turning Power On/Off ............................ 3 1.4 Transmitting, Standby............................. 3 1.5 Adjusting Display Contrast, Brilliance .... 4 1.6 Choosing the Range .............................. 4 1.7 Receiver Sensitivity................................ 4 1.8 Suppressing Sea Clutter ........................ 5 1.9 Suppressing Rain Clutter ....................... 6 1.10 Measuring the Range............................. 6 1.11 Measuring the Bearing ........................... 7 1.12 Shifting the Display ................................ 7 1.13 Zoom ...................................................... 8 1.14 User Menu Overview.............................. 8 1.15 Heading Line .......................................... 9 1.16 Interference Rejector.............................. 9 1.17 Noise Rejector...................................... 10 1.18 Echo Trail, Trail Brilliance..................... 10 1.19 Echo Stretch......................................... 10 1.20 Guard Alarm ..........................................11 1.21 Watchman ............................................ 12 1.22 Suppressing Long-range Rain Clutter.. 12 1.23 Panel Backlighting................................ 12 1.24 Hue....................................................... 13 1.25 Resetting Distance Run ....................... 13 1.26 PROG Key............................................ 13 1.27 Outputting Target Position to a Plotter . 13 1.28 Turning Navigation Data On/Off ........... 14 1.29 Setting up Nav Data Displays .............. 14 1.30 System Menu ....................................... 16 2. MAINTENANCE, TROUBLESHOOTING..... 18 2.1 Maintenance ......................................... 18 2.2 Replacing the Fuse...............................19 2.3 Troubleshooting ....................................19 2.4 Diagnostics ...........................................20 2.5 Test Pattern........................................... 21 2.6 Clearing the Memory ............................ 21 2.7 Replacing the Magnetron .....................21 2.8 Replacing the Synchro Belt .................. 21 3. INSTALLATION..................................... 22 3.1 Antenna Unit Installation.......................22 3.2 Display Unit Installation ........................25 3.3 Wiring.................................................... 25 3.4 Adjustments .......................................... 26 3.5 Magnetron Heater Voltage.................... 29 MENU TREE.............................................. 30 SPECIFICATIONS ..................................SP-1 PACKING LIST OUTLINE DRAWINGS INTERCONNECTION DIAGRAM SCHEMATIC DIAGRAMS
  iiSAFETY INSTRUCTIONSSafety Instructions for the OperatorWARNINGELECTRICAL SHOCK HAZARDDo not open the equipment.Only qualified personnelshould work inside theequipment.Wear a safety belt and hardhat when working on the antenna unit.Serious injury or death canresult if someone falls fromthe radar antenna mast.Do not disassemble or modify theequipment.Fire, electrical shock or serious injury canresult.Turn off the power immediately if waterleaks into the equipment or the equip-ment is emitting smoke or fire.Continued use of the equipment can causefire or electrical shock.Use the proper fuse.Use of a wrong fuse can damage theequipment and void the warranty.WARNING LABELA warning label is attached to the equipment. Do not remove the label.If the label is missing or damaged,contact a FURUNO agent or dealerabout replacement.WARNINGTo avoid electrical shock, do not remove cover. No user-serviceable parts inside.Name: Warning Label (1)Type: 86-003-1011-1Code No.: 100-236-231CAUTIONSafety Instructions for the InstallerObserve the following compass safedistances to prevent interference to amagnetic compass:Standard    Steeringcompass    compass0.60 m       0.40 mAntennaunit 1.25 m       0.85 mDisplayunitELECTRICAL SHOCK HAZARDDo not open the equipmentunless totally familiar withelectrical circuits andservice manual.Only qualified personnelshould work inside theequipment.Wear a safety belt and hardhat when working on theantenna unit.Serious injury or death canresult if someone falls fromthe radar antenna mast.WARNINGConstruct a suitable service platformfrom which to install the antenna unit.Serious injury or death can result if some-one falls from the radar antenna mast.Be sure that the power supply iscompatible with the voltage rating ofthe equipment.Connection of an incorrect power supplycan cause fire or damage the equipment.Use only the specified power cable.Fire or damage to the equipment  canresult if a different cable is used.CAUTION
  iiiFOREWORD A Word to the Owner of the MODEL 1715 Congratulations on your choice of the FURUNO MODEL 1715 Marine Radar.  For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.    Your radar is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended function unless installed, operated and maintained properly. Please carefully read and follow the recommended procedures for installation, operation, and maintenance.   We would appreciate hearing from you, the end-user, about whether we are achieving our purposes.   Thank you for considering and purchasing FURUNO equipment.   Features Your radar has a large variety of functions, all contained in a rugged plastic case. All controls respond immediately to the operator’s command and each time a key is pressed the corresponding change can be seen on the screen.  The main features of the MODEL 1715 are • Daylight viewing radar specially designed for small craft and sailing yachts. • Traditional FURUNO reliability and quality in a compact, light-weight and low-cost radar. • Compact and light-weight radome antenna with precision 45 cm center-fed radiator. • High definition 7-inch monochrome LCD display. • Automatic control of sensitivity (gain), tuning and A/C SEA for simplified operation. • Targets can be displayed in grey tones on a white background or vice versa, for optimal viewing under any lighting conditions. • On-screen alphanumeric readout of all operational information. • User programmable nav data displays. • [PROG] key acts as a menu shortcut key. • [TLL] key outputs chosen target’s L/L position to a plotter. • Standard features include Display Shift, EBL, Echo Stretch, Echo Trail, Guard Alarm, Interference Rejector, VRM, Zoom. • Guard zone watches for targets entering (or exiting) a guard zone. • Operates on 12 or 24 V DC power.
  ivSYSTEM CONFIGURATIONDISPLAY UNITRDP-142EXTERNALBUZZERXH3-BZ-L970SHIP'S MAINS12-24 VDCRECTIFIERPR-62: Standard supply: Optional supply: Local supplySHIP'S MAINS115/230 VAC,1φ, 50/60 HzNAVIGATORor ECHO SOUNDER(NMEA 0183)ESCMENUMODEVRMEBLPOWERBRILLGAINALARMRANGEGPS RECEIVERGP-310B/320BWIND INDICATOR,SPEED INDICATORANTENNA UNITRSB-0095TLLPROG
  vEQUIPMENT LISTS Standard supply Name Type Code No. Qty  Remarks Antenna Unit  RSB-0095  —  1   Display Unit  RDP-142  —  1   CP03-25301  008-442-280  1 set  For antenna unit, including EMI core CP03-24910  000-080-231  Antenna cable (10 m)   CP03-24920  000-080-232  Antenna cable (15 m) CP03-24930 000-080-233 1 set Antenna cable (20 m) Installation Materials* CP03-25101  008-441-250  1 set  For display unit, including tapping screws for mounting hanger Spare Parts*  SP03-09800  000-085-441  1 set  Fuse *: See packing list at end of manual.  Option Name Type Code No. Qty Remarks Buzzer Assy.  XH3-BZ-L970  000-146-422  1  With connector, 0.9 m Cable Assy.  MJ-A7SPF0007-050  000-144-418  1  Connector at one end, 5 m, for NMEA equipment Cable Assy.  MJ-A15A7F0004-005  000-145-690  1 For NMEA equipment, 0.5 m, connector at both ends, 7P-7P/6P Cable Assy.  A15A7F0005-020  000-145-691  1  7P-7P, for NMEA equipment, 2 m Cable Assy.  MJ-A10SPF0003-300  000-130-034  1  Antenna cable, 30 m, for 24 VDC power Radome Mounting Bracket  OP03-93 008-445-080 1 For mounting antenna unit on a sailboat PR-62 000-013-484 100 VAC PR-62 000-013-485 115 VAC PR-62 000-013-486 220 VAC Rectifier PR-62 000-013-487 1 230 VAC
  11. OPERATION 1.1 Controls Cursor PadChooses menu items;adjusts VRM, EBL and cursor.Opens/closes menu;escapes from current operation.Chooses display mode.Opens dialog box for adjustmentof gain, A/C SEA, A/C RAIN.Chooses radar range.Enables/disables guard alarm.Turns EBL on/off.Short press: Turns power on.Long press: Turns power off. Momentary press: Opens dialog box for(power turned on) adjustment of displaycontrast, brillianceand mode (TX, ST-BY)selection.ESCMENUMODEVRMEBLPOWERBRILLGAINALARMRANGETLLPROGTurns VRM on/off.Shortcut keyOutputs chosen target’s L/Lposition to plotter.How to remove the hard coverPlace your thumbs at the center of the cover, and then lift the cover whilepressing it with your thumbs.  Display unit
                                                                       1. OPERATION  21.2 Indications TRAILG(IN)ES HIR HFTC0.51.5nmZOOMRangeRange ring intervalZoomEcho trails Guard alarm (IN or OUT)Echo stretchRain clutter suppressorGuardzoneCursorEBLRange ringsRange, bearing andtime-to-go to cursorlocation(Cursor latitude andlongitude positionalso available if radaris interfaced witha navigator.)EBL bearingVRM rangeVRMWatchmanHeading lineWATCHSIMSimulation modeInterference rejectorAppropriate sensors required to display nav data.EBL/VRM BoxEBLVRM45.0°1.25 RNG 06.2nmBRG 283.2°TTG: 02H21MRngXTEBrgCse8.56 nm0.39 nm306°155°Trip meter Position 34°22.539 N136°07.516 ERange,XTE (Cross-track error)PositionBearing,Course Indications  About the LCD The high quality LCD displays better than 99.99% of its picture elements. The remaining 0.01% may drop out or light, however this is not an indication of malfunction; it is a characteristic of the LCD.
1. OPERATION  31.3  Turning Power On/Off Press the [POWER/BRILL] key to turn on the power. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation and displays program number. The ROM and RAM check shows OK or NG (No Good). If NG appears, try to press any key except the [POWER/BRILL] key to start operation. However, the equipment may not work properly. Contact your dealer for advice.  XX.XX = Program version no.     ROM : OK     RAM : OK  Program No: 0359199-XX.XXFURUNO ELECTRIC CO., LTD.7" LCD MARINE RADAR Startup screen After the completion of the startup test, a timer displays the time remaining for warm up of the magnetron (the device which transmits radar pulses), counting down from 1:00 to 0:00.  To turn off the power, press and hold down the [POWER/BRILL] key (about three seconds) until the screen goes blank.    Provided that the radar was once in use with the transmitter tube (magnetron) still warm, you can turn the radar into TRANSMIT condition without 1-minute of warm-up. If the [POWER/BRILL] switch was accidentally turned off and you want to restart the radar promptly, turn on the [POWER/BRILL] switch not later than 15 seconds after power-off.  Note 1: In a cold environment the screen appears “foggy” when the power is turned on but is soon restored to normal condition. Note 2: The example screens shown in this manual may not match the screens you see on your display. The screen you see depends on your system configuration and equipment settings.   1.4 Transmitting, Standby After the power is turned on and the magnetron has warmed up, “ST-BY” (Stand-by) appears, indicating the radar is ready to transmit radar pulses.  To toggle between transmit and stand-by, do the following:  1.  With the power turned on, press the [POWER/BRILL] key momentarily to show the brilliance/contrast adjustment window. CONT:                  4 LOW          HIGHBRILL:                                   LOW          HIGH9BRILL/CONTRAST[MODE]: TX/ST-BY[MENU/ESC] : Exit. Brilliance/contrast adjustment window 2.  Press the [MODE] key to go to stand-by and transmit status alternately. Note: If you attempt to transmit before “ST-BY” appears, the beeps sound and the radar does not transmit pulses. Wait until “ST-BY” appears. 3.  Press the [MENU/ESC] key to close the window.  When radar pulses are transmitted the radar receiver is automatically tuned. Echoes appear in four levels of digitized video according to echo strength. When a target is beneath a marker (VRM, EBL, heading line, range ring) the part of the marker where the target lies is displayed in reverse video.
                                                                       1. OPERATION  41.5 Adjusting Display  Contrast, Brilliance 1.  With the power turned on, press the [POWER/BRILL] key momentarily to show the brilliance/contrast adjustment window. CONT:                  4 LOW          HIGHBRILL:                                   LOW          HIGH9BRILL/CONTRAST[MODE]: TX/ST-BY[MENU/ESC] : Exit. Brilliance/contrast adjustment window 2. Press ◄ or ► to adjust contrast. 3. Press ▲ or ▼ to adjust brilliance. 4.  Press the [MENU/ESC] key to escape.  Note 1: Windows other than menu windows are erased when there is no operation within about 10 seconds.  Note 2: The radar starts up with the last-used brilliance level after the startup screen appears. Therefore, adjust the brilliance if it is too low at startup.   1.6  Choosing the Range The range selected automatically determines the range ring interval, the number of range rings and pulse repetition rate.  Press the [RANGE+] or [RANGE-] key to choose the range. The range and range ring interval appear at the top left corner on the screen.           RangeRange ringinterval6.0 nm2.0RNG 03.2nmBRG 60.2°TTG 02H21MEBL  - - - .-°VRM - - - -nm Location of range and range ring interval indications   1.7 Receiver Sensitivity The [GAIN] key adjusts the sensitivity (gain) of the receiver. It works in precisely the same manner as the volume control of a broadcast receiver, amplifying the signals received.  To set the sensitivity, you first choose the automatic sensitivity setting which best matches current sea condition. Then, if necessary, you may fine tune the sensitivity manually. The proper setting is such that the background noise is just visible on the screen.   If you set up for too little sensitivity, weak echoes may be missed. On the other hand excessive sensitivity yields too much background noise; weak targets may be missed because of the poor contrast between desired echoes and the background noise on the display.  1.  Press the [GAIN] key consecutively until the display shown below appears. GAIN20[GAIN]  :  A/C SEA MENU[MENU/ESC] :  Exit.AUTO      : MODERATEMANU Gain adjustment window
1. OPERATION  52. Press ▲ or ▼ to choose AUTO or MANU as appropriate. Automatic gain adjustment 1) Press ► to open the automatic gain options window. ROUGHMODERATECALM Automatic gain options 2) Press ▲ or ▼ to choose ROUGH, MODERATE or CALM depending on sea conditions. 3) Press ◄ to close the window. Manual gain adjustment While observing the screen and the gain tuning bar, press ◄ or ► to adjust the gain. The setting range is 0-100. 3.  Press the [MENU/ESC] key to finish.   1.8  Suppressing Sea Clutter In rough weather, returns from the sea surface, called sea clutter, are received over several miles around own ship and mask nearby targets. This situation can be improved by properly suppressing the sea clutter with the A/C SEA control.  To set the A/C SEA, you first choose the automatic A/C SEA setting which best matches current sea conditions. Then, if necessary, you may fine tune the A/C SEA manually.  In most cases suppress the clutter until it has disappeared to leeward, but a little is still visible windward. If the setting is too low, targets will be hidden in the clutter, while if it is set too high, both sea clutter and targets will disappear from the display.    A common mistake is too over-suppress sea clutter so that it is completely removed. You can see how dangerous this can be by setting up for maximum A/C SEA: A dark zone will be created near the center of the screen, causing a loss of close-in targets. This dark   zone is even more dangerous if the sensitivity has not been properly adjusted.    Always leave a little sea clutter visible on the   screen, first adjusting automatically and then fine tuning with the manual control as necessary.   Sea clutter at screen center 1.  Press the [GAIN] key consecutively until the display shown below appears. A/C SEA20[GAIN]  :  A/C RAIN MENU[MENU/ESC] :  Exit.AUTO      : MODERATEMANU A/C SEA adjustment window 2. Press ▲ or ▼ to choose AUTO or MANU as appropriate. Automatic A/C SEA adjustment 1) Press ► to open the automatic A/C SEA options window. ROUGHMODERATECALM A/C SEA options 2) Press ▲ or ▼ to choose ROUGH, MODERATE or CALM depending on sea conditions. 3) Press ◄ to close the window.
                                                                       1. OPERATION  6Manual A/C SEA adjustment While observing the screen and the A/C SEA tuning bar, press ◄ or ► to adjust the A/C SEA. The setting range is 0-100. 4.  Press the [MENU/ESC] key to finish.   1.9  Suppressing Rain Clutter The vertical beamwidth of the antenna is designed to see surface targets even when the ship is rolling. However, by this design the antenna will also pick up rain clutter (rain, snow, or hail) in the same manner as normal targets. The illustration below shows the appearance of rain clutter on the display.  The A/C RAIN control adjusts the receiver sensitivity as the A/C SEA control does but rather in a longer time period (longer range). The higher the setting the greater the anti-clutter effect.  Rain clutter at screen center 1.  Press the [GAIN] key consecutively until the display shown below appears. A/C RAIN[GAIN]  :  GAIN MENU[MENU/ESC] :  Exit.65 A/C RAIN adjustment window 2.  While observing the screen and the A/C RAIN tuning bar, press ◄ or ► to adjust the A/C RAIN. The setting range is 0-100. 3.  Press the [MENU/ESC] key to finish. 1.10 Measuring the Range The bearing to a target can be measured by the range rings, by the cursor and by the VRM (Variable Range Marker).  Measuring range by the cursor Operate the cursor pad to place the cursor on the inside edge of the target. Read the range to the cursor at the bottom right corner of the display.  Measuring range by the range rings Count the number of rings between the center of the display and the target. Check the range ring interval and judge the distance of the echo from the inner edge of the nearest ring.   Measuring range by the VRM 1.  Press the [VRM] key to display the VRM. The message “Adjust VRM by cursor” appears and “VRM” in the EBL/VRM box is displayed in reverse video. The message is automatically erased after 10 seconds, or you may erase it sooner by pressing any key. 2.  Operate the cursor pad to place the VRM on the inside edge of the target. 3.  Check the VRM readout at the bottom left corner on the screen to find the range to the target.  To anchor the VRM, press the [MENU/ESC] key. (It is automatically anchored if there is no key operation for about 10 seconds.) To erase the VRM, press the [VRM] key. 6.0nm2.0 TargetVRMVRMrangeRange, bearingand time-to-goto cursor locationRNG 2.22nmBRG 45.62°TTG 02H21MCursorEBL  - - - .-°VRM 2.91nm How to measure the range
1. OPERATION  71.11 Measuring the Bearing The bearing to a target can be measured with the cursor and the EBL (Electronic Bearing Line).   Measuring bearing with the cursor Operate the cursor pad to place the cursor on the inside edge of the target. Read the bearing to the target at the bottom right corner.  Measuring bearing with the EBL 1.  Press the [EBL] key to show the EBL. The message “Adjust EBL by cursor” appears and “EBL” in the EBL/VRM box is displayed in reverse video. The message is automatically erased after 10 seconds, or you may erase it sooner by pressing any key. 2.  Operate the cursor pad to bisect the target with the EBL. 3.  Check the EBL readout at the bottom left corner on the screen to find the bearing to the target.  To anchor the EBL, press the [MENU/ESC] key. (It is automatically anchored if there is no key operation for about 10 seconds.) To erase the EBL, press the [EBL] key. 6.0nm2.0 EBLbearingRNG 2.22nmBRG 45.62°TTG 02H21MRange, bearingand time-to-goto cursor locationTargetEBL CursorEBL 45.62°VRM - - - -nm Measuring range by the EBL and cursor   1.12 Shifting the Display Own ship position, or sweep origin, can be displaced manually or automatically to expand the view field without switching to a longer range. The default shift method is manual.  If shift is activated when nav data is displayed, the nav data is automatically erased.  1.  Use the cursor pad to place the cursor where you want to shift own ship position. 2.  Press the [MODE] key to show the Display Mode menu.         DISPLAY MODE[MENU/ESC]  :  ExitSHIFT (MANUAL)*NORMALZOOMNAV DISP          OFF     ON* UTO i d f M NU L Display mode menu *: If SHIFT (AUTO) is shown, open the System menu and set SHIFT MODE to MANUAL. For further details, see SHIFT MODE on page 17. 3. Press ▲ to choose SHIFT (MANUAL). 4.  Press the [MENU/ESC] key to close the menu.  Select where to shift                   Shifted displaywith the cursor.ChoosemanualSHIFTmode. How the manual shift works To cancel the shifted display, open the Display Mode menu, set SHIFT to NORMAL and then press the [MENU/ESC] key.
                                                                       1. OPERATION  81.13 Zoom The zoom feature allows you to double the size of a selected area.  If zoom is activated when nav data is displayed, the nav data is automatically erased.  1.  Use the cursor pad to place the cursor where you want to zoom. 2.  Press the [MODE] key to show the display mode menu.         DISPLAY MODE[MENU/ESC]  :  ExitSHIFT (MANUAL)*NORMALZOOMNAV DISP          OFF     ON Display mode menu 3. Press ▼ to choose ZOOM. 4.  Press the [MENU/ESC] key to close the menu. “ZOOM” appears at the top left corner when the zoom feature is turned on. 6.0nm2.0ZOOM ZoomWindowRNG 4.43nmBRG 231.3°TTG: 02H21M+CursorEBL  - - - .-°VRM - - - -nmZOOM Zoom display To cancel the zoom display, open the Display Mode menu, choose NORMAL and then press the [MENU/ESC] key. To choose new zoom location, restore to the NORMAL mode and then repeat the zoom procedure.   1.14 User Menu Overview The User menu, consisting of three pages of menus, contains 12 items which the user may set according to conditions or preference.  1.  Press the [MENU] key to open the User menu. P(1/3)INT REJECTION   LOWECHO STRETCH : LOWFTC : OFFNOISE REJECTION: LOW[MENU/ESC]   :  Exit.** = "P" shows current function of PROG key User menu, page 1 2. Use ▲ or ▼ to scroll the menu to display desired item in reverse video. Page 2(3/3)Page 3WATCHMAN TIME   OFFHUE : DAYPANEL DIMMER : OFFHDG LINE OFF[MENU/ESC]   :  Exit.(2/3)ECHO TRAIL   OFFTRAIL BRILLIANCE : LOWTRIPLOG RESET?SYSTEM MENU...[MENU/ESC]   :  Exit. User menu, pages 2 and 3 3. Press ► to show the options window for the item selected. For example, the illustration below shows the interference rejector options window. OFFLOWMEDIUMHIGH Interference rejector options 4. Press ▲ or ▼ to choose option desired. 5. Press ◄ to continue menu operation, or press the [MENU/ESC] key to register your selection and close the User menu.
1. OPERATION  9User menu description Item Description INT REJECTION Rejects radar interference. ECHO STRETCH Stretches echoes in range direction or range and bearing direction. FTC  Suppresses long-range rain clutter. NOISE REJECTION Rejects noise. WATCHMAN TIME Periodically checks for targets in guard zone. HUE  Chooses echo and background tones. PANEL DIMMER Adjusts panel backlighting. HDG LINE OFF Temporarily turns the heading line off. ECHO TRAIL  Shows echo movement in afterglow. TRAIL BRILLIANCE Adjusts echo trail brilliance. TRIPLOG RESET? Resets distance run. SYSTEM MENU Opens the system menu. For description see paragraph 1.30.   1.15 Heading Line The heading line indicates the ship’s heading and it is the solid line which appears at zero degrees on the bearing scale.  To temporarily erase the heading line to look at targets existing dead ahead of own ship, do the following:  1.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose HDG LINE OFF from page 2. 3. Press ► to turn the heading line off. The line stays off while ► is pressed. 4.  Press the [MENU/ESC] key to close the menu.   1.16 Interference Rejector Mutual radar interference may occur in the vicinity of another shipborne radar operating in the same frequency band (9 GHz). It is seen on the screen as a number of bright spikes either in irregular patterns or in the form of usually curved spoke-like dotted lines extending from the center to the edge of the picture. This type of interference can be reduced by activating the interference rejector circuit. “IR” and the rejection level indicator “L,” “M” or “H” appear at the top right corner when the interference rejector circuit is on.  Appearance of interference Turn off the interference rejector when no interference exists, to avoid missing small targets.  1.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose INT REJECTION from page 1. 3. Press ► to open the options window. 4. Press ▲ or ▼ to choose OFF, LOW, MEDIUM or HIGH as appropriate. 5.  Press the [MENU/ESC] key to finish.
                                                                       1. OPERATION  101.17 Noise Rejector The noise rejector suppresses white noise, which appears on the screen as many dots scattered randomly over the display.  1.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose NOISE REJECTION from page 1. 3. Press ► to open the options window. 4. Press ▲ or ▼ to choose OFF, LOW or HIGH as appropriate. 5.  Press the [MENU/ESC] key to close the menu.   1.18 Echo Trail, Trail Brilliance Echo trails are the afterglow of target echoes that represent their movements relative to own ship. They are useful for monitoring target movement.  Trails are painted for the time period chosen. When the time period has elapsed, trails are erased and restarted. Trails are also erased and restarted whenever the range is changed or zoom or shift is activated.      30S TRAILTrail time(No time shownin case ofcontinuous trails)Echo trail Echo trails 1.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose ECHO TRAIL from page 3. 3. Press ► to open the options window. OFF30sec1min3min6minCONTIN. Echo trail options 4. Press ▲ or ▼ to choose appropriate time, or OFF to cancel echo trails. “CONTIN.” paints trails continuously. 5. Press ◄ to close the options window.   6. Press ▼ to choose TRAIL BRILLIANCE. 7. Press ► to open the options window. 8. Press ▲ or ▼ to choose LOW or HIGH as appropriate. 9.  Press the [MENU/ESC] key to close the menu.  “TRAIL” and trail time (no time shown in case of “CONTIN.”) are shown at the upper right-hand corner on the screen.    1.19 Echo Stretch On long ranges target echoes tend to shrink, making them difficult to see. To enhance target video on long ranges, use the echo stretch feature.  1.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose ECHO STRETCH from page 1. 3. Press ► to open the options window. 4. Press ▲ or ▼ to choose OFF, LOW or HIGH as appropriate. LOW stretches echoes in the bearing direction; HIGH stretches echoes in the range and bearing directions. “ES L” or “ES H” appears at the top right-hand corner when echo stretch is turned on. 5.  Press the [MENU/ESC] key to close the menu. EchoES L ES HBrg dir.   Brg dir.Rngdir.Echo Stretch      Echo Stretch        Echo Stretch     OFF                    LOW                   HIGH How echo stretch works
1. OPERATION  111.20 Guard Alarm The guard alarm allows the operator to set the desired range and bearing for a guard zone. When ships, islands, landmasses, etc. violate the guard zone, audio and visual alarms are released to call your attention. The alarms will be released for targets entering or exiting the zone depending on the presence or absence of targets in the zone when the alarm is set.   *The alarm should not be relied upon as thesole means for detecting possible collisionsituations.*A/C SEA, A/C RAIN, FTC and GAIN controls   should be properly adjusted to be sure the   weak echoes will not be missed by the alarm.NOTICE Setting a guard zone 1.  Operate the cursor pad to place the cursor at the top left corner for the zone and then press the [ALARM] key. 2.  Operate the cursor pad to place the cursor at the bottom right corner for the zone and then press the [ALARM] key. Guardzoneto set      G(---)1)Place cursor attop left corner forzone and press[ALARM]. Place cursorhere.Mentally createthe guard zoneto set.2)Place cursor atbottom right cornerfor zone and press[ALARM].Guard zonecompleted.GuardzonePlace cursorhere.G(---)    G(---) How to set a guard zone How guard zone type is determined After the guard zone has been set, the radar checks for targets inside the guard zone, which takes about 8 to 12 seconds. When the check is completed, “G(IN)” or “G(OUT)” replaces G(---) at the top right corner.  G(IN): When no target exists in the zone, "G(IN)" appears. The audio alarm sounds against targets which enter the guard zone. G(OUT): If there are targets in the guard zone, "G(OUT)" appears. The audio alarm sounds against all targets which exit from the guard zone. (a) Inward target alarm (b) Outward target alarm Inward and outward alarms Note: The guard zone disappears when it is not within the range in use. When this occurs "UP RNG" replaces G(IN) or G(OUT). Change the range to redisplay the guard zone.  Silencing the audio alarm When a target violates the guard zone, the target flashes and the audio alarm sounds. You can silence the audio alarm with the [ALARM] key. The target continues flashing until it no longer violates the guard zone or the guard zone is canceled.  Canceling the guard zone and guard alarm Press and hold down the [ALARM] key until the guard zone is erased.
                                                                       1. OPERATION  121.21 Watchman The radar "wakes up" at specified time intervals (5, 10, or 20 minutes) and operates for 10 scans, the start of which is announced by releasing the audio alarm. If change is found in the guard zone from the previous 10 scans, the audio alarm sounds and the radar resumes normal operation, canceling the watchman mode. If no change is found, the radar goes into stand-by, for the specified time interval. This feature is useful for periodic watch of the guard zone. ST-BY5,10or20 min  Tx1 min  Tx1 minWatchmanstarts5,10or20 minST-BY*** Beeps emitted just before radar transmits. How watchman works  1.  Set a 360° guard zone referring to paragraph 1.20. 2.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose WATCHMAN TIME from page 2. 3. Press ► to open the options window. OFF5 min10 min20 min Watchman time options 4. Press ▲ or ▼ to choose appropriate time out, that is, the amount of time the radar waits in standby, among 5, 10 and 20 minutes. 5.  Press the [MENU/ESC] key to close the menu.   1.22 Suppressing Long-range Rain Clutter In adverse weather, clouds, rain or snow produce spray-like spurious echoes which impair target detection over a long distance. These echoes can be suppressed by turning on the FTC (Fast Time Constant). FTC works by splitting up these unwanted echoes into a speckled pattern, making recognition of solid targets easier.  1.  Press the [MENU/ESC] key. 2. Press ▲ or ▼ to choose FTC from page 1. 3. Press ► to open the options window. 4. Press ▲ or ▼ to choose OFF or ON as appropriate. 5.  Press the [MENU/ESC] key to close the menu.  “FTC” appears at the top right corner when the FTC is active.   1.23 Panel Backlighting You may adjust panel backlighting as follows:  1.  Press the [MENU/ESC] key to open the User menu. 2.  Choose PANEL DIMMER from page 2. 3. Press ► to open the options window. 4.  Choose OFF, LOW, MEDIUM or HIGH as appropriate. 5.  Press the [MENU/ESC] key to close the menu.
1. OPERATION  131.24 Hue The default hue setting (DAY) displays echoes in tones of gray on a white background, which is most suitable for daytime viewing. For nighttime viewing you may reverse this arrangement.  1.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose HUE from page 2. 3. Press ► to open the options window. 4. Press ▲ or ▼ to choose DAY or NIGHT as appropriate. 5.  Press the [MENU/ESC] key to close the menu.   1.25 Resetting Distance Run   You may reset distance run to zero as below. You need a navigator or speed log to display distance run.  1.  Press the [MENU/ESC] key to open the User menu. 2. Press ▲ or ▼ to choose “TRIPLOG RESET?” from page 3. 3. Press ► to open the options window. 4. Press ▲ to choose YES to reset distance run to zero. 5.  Press the [MENU/ESC] key to close the menu.   1.26 PROG Key The [PROG] key acts as a shortcut key. You may use any User menu item except “TRIPLOG RESET?” and “SYSTEM MENU.”  Using the PROG key 1.  Press the [PROG] key. The options window corresponding to the item programmed appears. In the example at the top of the next page the echo stretch options window is shown. OFFLOWHIGHECHO STRETCH Echo stretch options window 2. Press ▲ or ▼ to choose appropriate option. 3.  Press the [MENU/ESC] key to close the options window.  Programming the PROG key 1.  Press the [MENU/ESC] key to open the User menu. “P” marks the current function of the [PROG] key. P(1/3)INT REJECTION   LOWECHO STRETCH : LOWFTC : OFFNOISE REJECTION: LOW[MENU/ESC]   :  Exit.* User menu, page 1 2. Press ▲ or ▼ to choose the item you wish to use. 3.  Press and hold down the [PROG] key (about three seconds) until you hear a beep and the “P” moves to the item selected. 4.  Press the [MENU/ESC] key to close the menu.   1.27 Outputting Target Position to a Plotter If the radar is interfaced with a plotter, you can output a radar target’s latitude and longitude position to the plotter, and show that position on the plotter’s screen, with the target mark (X). This function requires position and heading data.  1.  Use the cursor pad to place the cursor on a target. 2.  Press the [TLL] key to output the target’s L/L position.
                                                                       1. OPERATION  141.28 Turning Navigation Data On/Off Navigation data appears on the bottom half of the screen as in the illustration below. You may turn the navigation data display on or off as shown below.    Note: When the nav data is turned on with shift or zoom active, zoom or shift is cancelled.  1.  Press the [MODE] key. 2. Press ► to choose ON; ◄ to choose OFF. 3.  Press the [MENU/ESC] key to close the menu. 6.0 nm2.0RNG 2.22nmBRG 45.62°TTG 02H21M+PositionNavData  34°44.135 N135°44.135 ESpeed                  Course10.2 kt                          135°PositionEBL  - - - .-°VRM - - - -nm  Sample navigation display   1.29 Setting up Nav Data Displays The user may arrange the nav data display as desired. You may display between two and four items and choose the item and the order to display them. For how to choose the number of items to display, see “NAV DATA” on page 16.  1.  Turn on the nav data referring to paragraph 1.28. 2.  Press the [POWER/BRILL] key momentarily followed by the [MODE] key to go into stand-by. 3.  Press the [MENU/ESC] key to close the window.  4.  Press the cursor pad to display the nav data setup window. Position                  30°00.065'N130°00.574'EDATE09 10 02DATE09 10 02TIME14:25:030.25nmXTE 1       0.5         0       0.5       1Dashed rectanglecircumscribesselectionNAV DATA SETUP   /  : Window Selection   /  : Data Selection[MENU/ESC]  :  EnterNav datasetup window Nav data display with nav data setup window 4. Press ▲ or ▼ to choose the data window to process. The dashed rectangle circumscribes current selection. 5. Press ◄ or ► to choose item to display. See the illustration below for the data availability. A description of the nav data displays appears on the next page. Items displayable in (1) - (3): depth, position,course, date, time, range and bearing, trip distance,odometer distance, water temperature,heading, time-to-go to destination waypoint,XTE*, speed*, wind speed and direction*, destination waypoint data*, compass*        (9)(1)(2)(3)(4)(5)   (6)   (7)   (8)(1)(2)(3)(4) (5)(6) (7)(8) (9)Nav data at stand-byNav data on radar displayItems displayable in (4) - (9): depth, position,course, range and bearing, trip distance,odometer distance, water temperature,date, time, speed, heading, air pressure, time-to-goto destination waypoint, XTE, wind speed and direction* = Graphic display in standby2-itemdisplay3-itemdisplay4-itemdisplay Nav data window and item displayable 6.  Press the [MENU/ESC] key to close the nav data setup window.
1. OPERATION  15GRAPHIC DISPLAYS                                           DIGITAL DISPLAYS1       0.5         0       0.5       1Waypoint 03Rng 0.19nm           Brg 321° XTE 0.00nm          Cse 333°   DESTINATION WAYPOINT GRAPHICXTEscaleBearing,CourseDestinationwaypointdirectionDestinationwaypointdata:Name,Range to,XTEWindAPP*                        WIND GRAPHIC6012090030150180120150906030120°Speed    10.3  m/sCOMPASS GRAPHICSPEED GRAPHIC17.2Speed2050406030100Course                   123.0°COURSEDepth                    32.8ftDEPTHHeadingMAG#          HEADINGOdometer                       56nmODOMETERPosition                  30°00.065'N130°00.574'EPOSITIONTemperature                                     69.8°FWATER TEMPERATURETrip meter   121nmTRIP DISTANCETime to Go       00H30MTIME-TO-GO** Speed                    19.3ktSPEEDRange 1.21nm                   RANGE & BEARING**Bearing140°Wind SpeedAPP*       WIND SPEEDWind DirectionAPP*    WIND DIRECTIONktBearing todestinationwaypointCourse Brg30°Cse90°NE* = APP or TRUE depending on menusetting. See WIND SPD/DIR on page 17for description.** = Range and bearing to destination   waypoint# = MAG(netic) or TRUE. TRUE requiresheading sensor.SpeedometerNote: The graphic displays selected on thestandby display are repeated on the radar display.TD                   31234.556432.6LORAN C/DECCA TIMEDIFFERENCES    TIMETime14:25:03WinddirectionWind speedXTE (Cross-Track Error) GRAPHIC1       0.5         0       0.5       10.25nmXTE Digital XTEAnalog XTE(Bar moves rightor left accordingto amount anddirection of XTE)318°8.0m/s138°Date                   XTECROSS-TRACK ERROR2002 SEP 19DATE 0.24nm1       0.5         0       0.5       1 Nav data displays
                                                                       1. OPERATION  161.30 System Menu The System menu mainly contains items which once set do not require frequent adjustment. You may display this menu by choosing “SYSTEM MENU” from page 3 of the User menu and then pressing ►.      SYSTEM MENULANGUAGE   EnglishRANGE UNIT : nmDEPTH UNIT : ftSPEED UNIT : ktWIND UNIT : ktTEMP UNIT : °FNAV DATA :KEY BEEP : ONRINGS : OFFWAYPOINT MARK : OFF(1/3)[MENU/ESC]  :  Exit.   SYSTEM MENU(2/3)[MENU/ESC]  :  Exit.  SYSTEM MENU  (3/3)RANGE 0.125nm    ON0.25  nm : ON0.5    nm : ON0.75  nm : ON1       nm : OFF             1.5    nm : ON2       nm : OFF3       nm : ON4       nm : OFF6       nm : ON8       nm : ON            12       nm : ON            16       nm : ON            24       nm : ON [MENU/ESC]  :  Exit.PAGE 3PAGE 2PAGE 1Page no.EBL REFERENCE   TRUEBEARING READOUT : TRUECURSOR POSITION : RNG&BRGTRIP SOURCE : LAT/LONWIND SPD/DIR : APPARENTSHIFT MODE : MANUALAUTO SHIFT SPEED : 15TX SECTOR BLANK : OFFBLANKING START : 000°BLANKING AREA : 000°LOCAL TIME SETUP : +0:00ANTENNA SPEED : AUTO System menu System menu description Page 1 of system menu LANGUAGE: The system language is available in English, several European languages and Japanese. To change the language, choose language desired, and then press the [MENU/ESC] key.  RANGE UNIT: Chooses the unit of range measurement among nautical miles, kilometers and statute miles.  DEPTH UNIT: Chooses the unit of depth measurement among meters, feet, fathoms, Hiro (Japanese) and Passi/Braza. Requires depth data.  SPEED UNIT: Chooses the unit of speed measurement among knot, mile per hour and kilometer per hour. Requires speed data.  WIND UNIT: Chooses the unit of wind measurement among mile per hour, kilometer per hour and meters per second. Requires wind data.  TEMP UNIT: Chooses the unit of water temperature measurement from Celsius and Fahrenheit. Requires water temperature data.  NAV DATA: Chooses the amount of nav data to display among two, three and four items. Requires appropriate sensors.  KEY BEEP: A beep sounds to confirm valid and invalid operation. You can turn this beep on or off.  RINGS: Turns the range rings on or off.  WAYPOINT MARK: The waypoint mark shows the location of the destination waypoint set on a plotter. You can turn this mark on or off. Requires a plotter.      Waypoint mark    Waypointmark
1. OPERATION  17 Page 2 of system menu EBL REFERENCE: The EBL readout may be chosen from relative (relative to own ship’s heading) or true (referenced to the North). Heading data required for true bearing.  Note: If no bearing data is input, course data from the GPS navigator is used. In this case ship’s speed must be more than two knots.  BEARING READOUT: Course indication may be shown in true or magnetic (magnetic compass) degrees. Heading data required for true degrees.  CURSOR POSITION: Chooses the information to show for the cursor position: latitude and longitude or range and bearing from own ship. Latitude and longitude position requires a navigator.  TRIP SOURCE: Chooses the criteria for calculating distance run: latitude and longitude or speed. Requires navigator or speed log.  WIND SPD/DIR: True is the speed and direction (in relation to ship’s bow) of the wind felt or measured when stationary. Apparent is the direction (in relation to ship’s bow) and speed of the wind as it appears to those on board, relative to the speed and direction of the boat; combination of the true wind and the wind caused by the boat’s movement. Requires wind data.  SHIFT MODE: Own ship position, or sweep origin, can be displaced manually or automatically. For automatic displacement, the amount of shift is calculated with ship speed, and the amount is limited to 60% of the range in use. For example, if the “Auto Shift Speed” setting is 15 knots and the ship is running at 10 knots, the amount of shift will be about 40%. The formula for determining shift amount is as below. Requires speed data.  Ship’s speedShift speed setting  X 0.6 = Amount of shift(%) AUTO SHIFT SPEED: Sets the automatic shift maximum speed. The setting range is 1-99.  TX SECTOR BLANK: In some installations it may be unavoidable to locate the antenna where an object (mast, etc.) will prevent transmission within its breadth. You should disable transmission within this area by turning on this feature and setting the area with BLANKING START and BLANKING AREA below.  BLANKING START: Sets the starting point (000-359°) of the TX sector blanking area.  BLANKING AREA: Sets the end point of the TX sector blanking area (000-135°).  LOCAL TIME SETUP: Enter time difference between local time and UTC time to use local time. Press ▲ or ▼ to set value.  ANTENNA SPEED: Chooses antenna rotation speed from 24 rpm and AUTO. Use AUTO to automatically change the antenna rotation speed (24-41 rpm) according to pulse length*. Choose “24 rpm” to rotate the antenna at 24 rpm regardless of pulse length.  * =  Short pulse at high rotation speed; long   pulse at slow rotation speed.  Page 3 of system menu RANGE: Chooses the ranges to use.
  182. MAINTENANCE, TROUBLESHOOTINGWARNINGELECTRICAL SHOCK HAZARDDo not open the equipment.Only qualified personnelshould work inside theequipment.  2.1 Maintenance Regular maintenance is important for good performance. A maintenance program should be established and should at least include the items listed in the table below. Maintenance program Period Item  Check point  Action Fixing bolts for antenna unit Check for corrosion and if tightly fastened. Replace corroded bolts. Coat new bolts with anticorrosive sealant. Antenna unit cleanliness Check for foreign material. (Foreign material on the antenna unit can cause a considerable drop in sensitivity.) Clean the antenna unit with a freshwater-moistened cloth. Alcohol may be used. Do not use commercial cleaners to clean the antenna unit; they can remove paint and markings or deform the equipment. Antenna unit cover Check for cracks. Permanent damage to the unit’s circuitry will result if water leaks inside.If a crack is found, it should be temporarily repaired by using a small amount of sealing compound or adhesive. The unit should then be brought to your dealer for permanent repairs. 3 to 6 months Display unit case, LCD The display case and LCD will, in time, accumulate a coating of dust, and dust on the LCD tends to dim the picture. Wipe the LCD carefully to prevent scratching, using tissue paper and an LCD cleaner. To remove dirt or salt deposits, use an LCD cleaner, wiping slowly with tissue paper so as to dissolve the dirt or salt. Change paper frequently so the salt or dirt will not scratch the LCD. Do not use commercial cleaners to clean the display unit; they can remove paint and markings or deform the equipment. 6 months to 1 year Display unit connectors Check for tight connection and corrosion. If corroded, ask your dealer about replacement.
2. MAINTENANCE, TROUBLESHOOTING  192.2  Replacing the Fuse The fuse (5 A) in the power cable protects the equipment against reverse polarity of the ship’s mains, overcurrent, and equipment fault. If the fuse blows, find the cause before replacing it.    Use the proper fuse.Use of a wrong fuse may cause serious damage to the equipmentand void the warranty.CAUTION   2.3 Troubleshooting The table below provides simple troubleshooting procedures which the user can follow to restore normal operation. If you cannot restore normal operation contact your dealer for advice. Troubleshooting If… But… Then… nothing appears on the display or display contrast is poor • try adjusting LCD contrast. • battery may have discharged; check battery. • check if fuse has blown. you pressed the [POWER/BRILL] key to turn on the radar the control panel does not light adjust PANEL DIMMER on the User menu. the message “NO HEADING PULSE” or “NO BEARING PULSE” appears   check that the antenna cable is firmly connected. the radar has warmed up and you pressed the [MODE] key to transmit neither noise or targets appear (characters and markers do) • try adjusting gain, A/C SEA and A/C RAIN. • check antenna cable for damage. a key is pressed  nothing happens  key may be faulty. Contact your dealer. the display freezes    press the [POWER/BRILL] key about five seconds to turn off the power and then turn it on again.
2. MAINTENANCE, TROUBLESHOOTING  202.4 Diagnostics If you feel that your unit is not working properly, conduct the appropriate diagnostic test, display unit or antenna unit, to find the possible cause. If you cannot restore normal operation, contact your dealer for advice.  Display unit 1.  Turn on the power while pressing and holding down the [MENU/ESC] key. Continue pressing the [MENU/ESC] key until the Installation menu appears. SIMULATION OFFTEST ...LCD PATTERN ...MEMORY CLEAR NMEA PORT : IN/OUTNMEA OUTPUT : OFFGPS WAAS : OFFGOTO RADAR SETUP...INSTALLATION MENU** The simulation provides internallygenerated echoes, for use inexhibitions, etc. "SIM" appearsat the top left corner when thesimulation mode is active. Installation menu 2. Press ▼ to choose TEST.   3. Press ► to start the test. In a few moments the results will appear. ROM OKRAM OKNMEA  01Body: 39 C    Program No. 0359199-**.**Push [MENU] 3 times to exit.* Program no. of FURUNO BlackBox GPS**.** = Program version no.GPS (XXXXXXX-XX.XX): OK* Diagnostic test results Interpreting display unit test results Item Results ROM,  RAM OK: Normal NG: No Good NMEA  Test connector required to test. Normally, “01” is displayed. Body  Temperature of display unit 4.  The squares at the right side of the test results display are for checking controls. Press each key and the arrows on the cursor pad one by one. A control’s corresponding on-screen square “lights” in black if the control is working properly. 5.  To return to the Installation menu, press the [MENU/ESC] key three times. 6.  To restore normal operation, turn off the power and then turn it on again.  Antenna unit 1.  Display the installation menu as in step 1 in the display unit diagnostic test. 2. Press ▼ to choose GOTO RADAR SETUP and then press ►. Power is automatically reset. 3.  Press the [POWER/BRILL] and [MODE] keys to transmit. 4.  Press the [MENU/ESC] key. The menu below appears.   (4/4)RADAR SETUP  SCANNER TEST ...[MENU/ESC]: Exit. Page 4/4 of user menu 5. Press ▼ to choose SCANNER TEST. 6. Press ► to start the test. In a few moments the results will appear, similar to those shown at the top of the next page. 7.  To restore normal operation, turn off the power and then turn it on again.
2. MAINTENANCE, TROUBLESHOOTING  21ANTENNA STATUS : OK(47)#HEADING : OKBEARING : OK                                      (24.0rpm)*TUNE   :TOTAL ON TIME : 00000hTOTAL TX TIME : 00000hINPUT NMEARMA  RMB  RMC  BWC  GLL  GGAMTW  VTG  VHW  XTE   VBW  DPTDBK   DBS  DBT   HDT   HDG HDMBWR  GLC  GTD  MWV  ZDA# Numeric is status code.  For service technician.* Antenna rotation speed  24.0 = Long range  31.0 = Medium range41.0 = Short rangetypicalvalue[MENU/ESC]: Exit. Antenna test results The antenna unit and heading and bearing signals are checked, and the results shown as OK or NG (No Good). For any NG, contact your dealer for advice. Antenna unit RPM appears below the bearing signal test result.  Note: The result of ANTENNA STATUS is shown as “NG (0)” when the antenna test result screen is initially shown. To confirm the antenna status, press the [MENU/ESC] key and ►.  The “TUNE” bar shows radar receiver tuning status. Total on time and total TX times appear below the TUNE bar. Data sentences currently input to the radar are highlighted in the “INPUT NMEA” window.   2.5 Test Pattern This feature tests for proper display of tones.  1.  Turn on the power while pressing and holding down the [MENU/ESC] key. Continue pressing the [MENU/ESC] key until the Installation menu appears. 2. Press ▼ to choose LCD PATTERN. 3. Press ► to start the test. The entire screen is black. 4.  Press the [MENU/ESC] key and the screen turns white. 5.  Press the [MENU/ESC] key again and the screen shows a four-tone display. 6.  Press the [MENU/ESC] key again to return to the Installation menu. 7.  To restore normal operation, turn off the power and then turn it on again. WHITE FOUR-TONE    BLACKPress[MENU/ESC].Press[MENU/ESC]. Test patterns   2.6  Clearing the Memory You may want to clear the memory to start afresh with default settings. You can do this as follows:  1.  Turn on the power while pressing and holding down the [MENU/ESC] key. Continue pressing the [MENU/ESC] key until the Installation menu appears. 2. Press ▼ to choose MEMORY CLEAR. 3. Press ►. 4. Press ▲ to choose YES. 5.  To restore normal operation, turn the power off and then turn it on again.   2.7  Replacing the Magnetron When the magnetron has expired, distant targets cannot be seen on the display. When you feel that long range performance has decreased, contact a FURUNO agent or dealer about replacement of the magnetron. (Type: E3588, Code No: 000-142-270)   2.8  Replacing the Synchro Belt When the synchro belt has worn out, the sweep is not synchronized with antenna rotation, which results in an abnormal picture. When you suspect that the synchro belt has worn out, contact a FURUNO agent or dealer about replacement. (Type: 40 S2M 266UG, Code No: 000-808-743)
  223. INSTALLATION3.1  Antenna Unit Installation Mounting considerations When choosing a mounting location for the antenna unit, keep in mind the following points: • Install the antenna unit on the hardtop, radar arch or on a mast on an appropriate platform. (For sailboats, a mounting bracket is optionally available.) It should be placed where there is a good all-round view with, as far as possible, no part of the ship’s superstructure or rigging intercepting the scanning beam. Any obstruction will cause shadow and blind sectors. • In order to minimize the chance of picking up electrical interference, avoid where possible routing the antenna cable near other electrical equipment onboard. Also, avoid running the cable in parallel with power cables. • Separate the antenna unit from a magnetic compass by the distances noted below to prevent interference to the magnetic compass: Standard compass: 1.25 m Steering compass: 0.85 m  Mounting on a platform 1.  Remove mounting hardware at the bottom of the antenna unit; four each of hex bolts (M10X20), spring washers and flat washers. Save mounting hardware to use it to fix the antenna unit to the mounting platform later on. Flat washerSpring washerHex bolt (M10 x 20)BowSternCable gland Antenna unit, showing location of mounting hardware 2.  Construct a platform (wood, steel, or aluminum) of 5-10 mm in thickness referring to the outline drawing at back of this manual. Fasten the platform to the mounting location. Next, position the antenna unit so the cable gland faces toward boat’s stern. Note 1: If corrosive material is used for the platform, take appropriate anticorrosive measures to prevent corrosion. Note 2: When drilling holes in the platform, be sure they are parallel with the fore and aft line. 3.  Using the hex bolts, flat washers and spring washers removed at step 1, fasten the antenna unit to the platform. The torque should be between 19.6-24.5 N////m. Note: Longer hex bolts (M10 x 25) are supplied with the installation materials. Use them instead of the hex bolts removed earlier if the thickness of the mounting platform is 5-10 mm.
3. INSTALLATION  23FlatwasherAntenna baseassy.SpringwasherPlatformHex bolt(M10 x 25or M10 x 20)Apply silicone sealant.Platform thickness Bolt to use5 mm or under:  M10x205-10mm: M10x25over 10 mm:  locally supplied bolts*1*1: How to fasten the antenna base to platform 4.  Unfasten four screws to open the cover. Remove and discard the packing material inside the radome. Remove and discard the packing material.Snap holder Antenna unit, inside view The antenna base is fitted with a snap holder, which may be used to hang the cover after removal. Use the hole next to the screw hole inside the cover to hang it.  a)  Unfasten the snap assy. with the string attached at the holder in the antenna base. b)  Unwind the string. c)  Attach the snap to the screw hole on the inside of the cover. Note: Do not use the snap holder to hang objects other than the cover. 5.  Release the cable of the rotation detector from the cable clamp. 6.  Unfasten 11 screws to dismount the shield plate. 7.  Pass the antenna cable with connector through the gasket and cable clamp, and then tighten the cable gland. Two gaskets are supplied: one gray, one black. Use the proper gasket according to antenna cable used, referring to the illustration below. 67φ12Use gray gasket.49φ11Use black gasket. Antenna unit, top view 8.  Referring to the figure below, fasten the shield cable with a screw (M4 x 10) on the chassis to ground the unit.   Connect 9 pin connector here (J801).Connectshield here. How to connect the antenna cable to the antenna unit 9.  Attach the EMI core to the antenna cable. Set the EMI core fixing plate to the EMI core.  Pass the cable through the plateso the bend faces downward. EMI core fixing plate
3. INSTALLATION  2410. Connect the 9-pin connector of the antenna cable to J801. See the illustration on the previous page for location.   11. Refasten the shield plate with 10 screws. Be sure not to pinch the cable from the rotation detector with the shield plate.   12. Fasten the EMI core fixing plate with screw (supplied). Screw (M4 x 15)EMI CoreEMI CoreFixing PlateAlign bend with corner of chassis.  How to fix the EMI core 13. Temporarily close the cover. You will need to open the cover later to confirm magnetron voltage.  Mounting using the optional mounting bracket A mounting bracket for fastening the antenna unit to a mast (70-125 mm diameter) on a sailboat is optionally available.   Type OP03-93, Code 008-445-080 Contents of mounting bracket kit Name Type Code No. QtyBolt M4 x 12 000-804-725 4 Bolt M8 x 20 000-805-707 8 Mounting plate  03-018-9001-0 100-206-740 1 Support plate (1)  03-018-9005-0 100-206-780 1 Support plate (2)  03-018-9006-0 100-206-790 1 Bracket (1)  03-028-9101-0  100-206-810 1 Bracket (2)  03-028-9102-0  100-206-820 1 Fixing plate  03-028-9103-0  100-206-830 2  1.  Remove mounting hardware at the bottom of the antenna base. You may discard the mounting hardware.   2.  Assemble the mounting bracket as below and fasten it to a mast.   3.  Fasten the antenna unit to the mounting bracket with hexagon head bolts (M10 x 25, optional supply). Mounting plateSupport plate (1)Support plate (2)Bracket (1)Bracket (2)Fixing plateM8 x 20M8 x 20(A) Assembling the mounting bracketM4 x 12(B) Fastening antenna to mounting bracketM10 x 25M8 x 20 How to assemble the optional mounting bracket and mount the antenna 4.  Open the cover. 5.  Follow steps 5-12 in “Mounting on a platform.”
3. INSTALLATION  253.2 Display Unit Installation Mounting considerations When choosing a mounting location for the display unit, keep in mind the following points: • Keep the display unit out of direct sunlight. • The temperature and humidity should be moderate and stable. • Locate the unit away from exhaust pipes and vents. • The mounting location should be well ventilated. • Mount the unit where shock and vibration are minimal. • Keep the unit away from electromagnetic field-generating equipment such as motors and generators. • For maintenance and checking purposes, leave sufficient space at the sides and rear of the unit and leave slack in cables. • Separate the display unit from a magnetic compass unit by the distances noted below to prevent interference to the magnetic compass: Standard compass: 0.6 m Steering compass: 0.4 m • Be sure the mounting location is strong enough to support the weight of the unit under the continued vibration normally experienced on the boat.  Mounting  The display unit can be mounted on a desktop or overhead or flush mounted in a console.  Desktop, overhead mounting 1.  Fix the hanger to the mounting location with four tapping screws (supplied). 2.  Fit the knob bolts to the display unit. 3.  Set the display unit to the hanger.   4.  Tighten the knob bolts securely.  Flush mounting Cutout a hole in the mounting area, referring to the outline drawing at the back of this manual for dimensions. Fasten the display unit with four screws (M4 x 20, supplied).   3.3 Wiring Connect the antenna cable, the power cable and the ground wire as shown below. FUSE (5 A)POWER SUPPLY12/24 VDCPOWER CABLEDISPLAY UNITANTENNA UNITANTENNA CABLE*WHT (+) BLK (-)External Equipment(NMEA)GROUNDConnect groundwire to bolt fastened(or welded) to hull.* = Do not confuse theantenna cable with thetransducer cablefor the Echo Sounder      (ex. LS-6100). The transducercable is black; the antennacable is white and "RADAR"is written on the cable.DJ-1DJ-1NMEANMEA223311POWERPOWER12-24 VDC12-24 VDC Wiring
3. INSTALLATION  26Connecting external equipment A video sounder, navigator, plotter, wind indicator or GPS receiver GP-310 (320B) can be connected to the display unit. You will need an NMEA cable to make the connection.    To connect two navigators, use the optional cable MJ-A15A7F0004-005. Connect them referring to the interconnection diagram at the back of this manual.  Input sentences NMEA 0183 Version 1.5/2.0/3.0, 4800 bps Name Sentences Ship’s Speed  VTG>RMC>RMA>VBW>VHWDepth DPT>DBK>DBS>DBT Heading (T)*  HDT>HDG>VHW>HDM Heading (M)  HDM>HDG>VHW>HDT Course (T)  VTG>RMC>RMA Course (M)  VTG>RMC>RMA Range/Bearing RMB>BWR>BWC Waypoint RMB>BWR>BWC Own Ship Pos.  GGA>RMC>RMA>GLL Time Diff.  RMA>GLC>GTD Water Temp.  MTW Time, Date  ZDA>RMC Wind Data  MWV Cross-track Error RMB>XTE *Requires magnetic variation (output by navigator).  Output sentence NMEA 0183 Version 3.0, 4800 bps Name Sentence Target L/L  TLL  Connecting the external buzzer The optional external buzzer (type XH3-BZ-L970, code no. 000-146-422) sounds the alarm buzzer in a remove location.  Note: This procedure requires making a hole in the display unit, which can affect watertightness. FURUNO cannot guarantee watertight integrity after this modification is made. 1.  Detach the rear panel and place it out side up on a workbench. 2.  Use a hammer and a Philips head screwdriver to punch out a hole of ø16 at the location shown in the illustration below. Make a hole of φ16.Seal hole with sealingcompound afterconnecting cable.Connect cableto J6 on DU Board.DJ-1DJ-1NMEANMEA223311POWERPOWER12-24 VDC12-24 VDC Display unit, rear view 3.  Close the rear panel, making sure the gasket is correctly positioned. 4.  Plug in the connector of the external buzzer to J6 on the DU Board. 5.  Seal the hole with sealing compound. 6.  Fix the buzzer to the location desired with two tapping screws.   3.4 Adjustments After you have installed the radar, do the heading alignment and timing adjustment. If you are connecting external equipment, follow “NMEA port setup, GPS WAAS setup” (for GP-320B) also.  Heading alignment You have mounted the antenna unit facing straight ahead in the direction of the bow. Therefore, a small but conspicuous target dead ahead visually should appear on the heading line (zero degrees).  In practice, you will probably observe some small error on the display because of the difficulty in achieving accurate initial positioning of the antenna unit. The following adjustment will compensate for this error.
3. INSTALLATION  271.  Turn on the power while pressing and holding down the [MENU/ESC] key. Continue pressing the [MENU/ESC] key until the Installation menu appears. INSTALLATION MENU▲SIMULATION OFFTEST...LCD PATTERN...MEMORY CLEARNMEA PORT : IN/OUTNMEA OUTPUT : OFFGPS WASS : OFFGO TO RADAR SETUP... Installation menu 2. Press ▼ to choose GOTO RADAR SETUP. 3. Press ►. Power is then reset. 4.  Wait one minute, press the [POWER/BRILL] key followed by the [MODE] key to transmit. 5.  Press the [MENU/ESC] key to show the User menu. 6. Press ► to show the Radar Setup menu.   RADAR SETUP  HEADING ADJUST    TIMING ADJUSTSET ON TIME : 000000hSET TX TIME : 000000h[MENU/ESC]: Exit. Radar setup menu 7.  HEADING ADJUST is selected; press ► to show the options window.   RADAR SETUP  HEADING ADJUST    TIMING ADJUSTSET ON TIME : 000000hSET TX TIME : 000000h[MENU/ESC]: Exit.: YES: NO Radar setup menu (heading adjust) 8. Press ▲ to choose YES, and the display now looks as below.   HEADING LINE ADJUSTMENT BY’  ’ AND ’  ’ KEYS.THEN PUSH MODE KEY TO SET.Heading LineMessage Heading adjustment display 9.  Visually identify a suitable target (for example, ship or buoy) at a range between 0.125 to 0.25 miles. 10. Point your boat’s bow directly toward the target selected at step 9. 11. Locate the target selected at step 9 on the display and choose a range which places it in the outer half of the picture.   12. Press ◄ or ► to bisect the target with the heading line. Heading LineTarget Heading adjustment display 13. Press the [MODE] key. 14. Press the [MENU/ESC] key to return to the Installation menu. 15. Move the boat towards a small buoy and confirm that the buoy shows up dead ahead on the radar when it is visually dead ahead.
3. INSTALLATION  28Timing adjustment Sweep timing differs with respect to the length of the antenna cable. Adjust sweep timing to prevent pushing or pulling of the target as illustrated below and placement of targets at incorrect ranges. Correct Target pushedinwardTarget pushedoutward Improper and correct sweep timings 1.  Transmit on a range between 0.125 and 0.5 nm and adjust the sensitivity and A/C SEA. (See page 4 and 5 for procedure.) 2.  Choose TIMING ADJUST from the Radar Setup menu and press ►.   RADAR SETUP  HEADING ADJUST    TIMING ADJUSTSET ON TIME : 000000hSET TX TIME : 000000h[MENU/ESC]: Exit.: YES: NO Radar setup menu (timing adjust) 3. Press ▲ to choose YES, and the display now looks as below. SWEEP TIMING ADJUSTMENT BY’  ’ AND ’  ’ KEYS.THEN PUSH MODE KEY TO SET.Message Timing adjustment display 4.  Find a target which should be “straight” (harbor wall, straight pier) on the radar display. 5.  While looking at the target selected at step 4, straighten it by pressing ▲ or ▼. 6.  Press the [MODE] key. 7.  Press the [MENU/ESC] key to return to the Installation menu to complete the procedure below, or shut off the power if no external equipment is connected.  NMEA port setup, GPS WAAS setup The NMEA port can function as an input port or input/output port.  If you are using the GP-320B, turn on the GPS WAAS feature.  1.  Show the Installation menu and then press ▼ to choose NMEA PORT. 2. Press ► to display the NMEA port options window. 3. Press ▲ or ▼ to choose IN/OUT or IN/IN as appropriate. IN/OUT: Input and Output (default setting). For GP-320B choose this setting. IN/IN: Input only (Available with connection of multiple navigators.) 4.  If you selected IN/OUT at step 3, press ◄, ▼ to choose NMEA OUTPUT, and then press ► to display the NMEA OUTPUT options window. 5. Press ▲ or ▼ to choose OFF or ON. Choose ON to output input data. Choose OFF to not output data or if the GP-310B or GP-320B is connected. 6. Press ◄ to close the window. 7.  If the GP-320B is connected, press ▼ to choose GPS WAAS. Otherwise, go to step 10.   8. Press ► to open the window. 9. Press ▲ to choose message type. Note: WAAS is currently in the developmental stage. While in the developmental stage choose message type 02. Change to message type 00 when WAAS becomes fully operational. 10. Turn off the power.
3. INSTALLATION  293.5  Magnetron Heater Voltage Magnetron heater voltage is formed at the MD Board of the antenna unit and is preadjusted at the factory. Therefore, no adjustment is required. However, verify the voltage as below. WARNINGELECTRICAL SHOCK HAZARDDo not open the equipment.DO NOT attempt theprocedure below unless totally familiar with electricalcircuits. 1.  Open the antenna cover and open the shield plate. 2.  Turn on the power. DO NOT transmit. 3.  Connect a multimeter, set to 10 VDC range, between #6 (+) and #4 (-) of test point TP804 on the MD Board. TP804VR801 MD board 4.  Confirm that the multimeter shows 8.0 V ±0.1 V. If it does not, adjust potentiometer VR801 on the MD Board.   5.  Turn off the power. 6.  Fasten the shield plate. 7.  Close the antenna cover.
  30MENU TREE MENU/ESC key+POWER/BRILLkeySIMULATION (OFF, ON, HIGH) TEST (Tests display unit.)LCD PATTERN (Displays test pattern.)MEMORY CLEAR (Restores default menu settings.)NMEA PORT (IN/OUT, IN/IN)NMEA OUTPUT (OFF, ON)GPS WAAS (OFF, WAAS 00-27) GO TO RADAR SETUP        HEADING ADJUST (Adjusts heading.)TIMING ADJUST (Adjusts timing.)SET ON TIME (Displays total hours                        radar has been powered.)SET TX TIME (Displays total hours                       of transmission.)MENU/ESC key INT REJECTION (OFF, LOW, MEDIUM, HIGH) ECHO STRETCH (OFF, LOW, HIGH)FTC (OFF, ON)NOISE REJECTION (OFF, LOW, HIGH)WATCHMAN TIME (OFF, 5, 10, 20 min)HUE (DAY, NIGHT)PANEL DIMMER  (OFF, LOW, MEDIUM, HIGH) HDG LINE OFF (Temporarily turns off heading line.)ECHO TRAIL (OFF, 30 s; 1, 3, 6 min, CONTIN.)TRAIL BRILLIANCE (LOW, HIGH)TRIPLOG RESET?SYSTEM MENU LANGUAGE (ENGLISH, JAPANESE, Others)RANGE UNIT (nm, km, sm)DEPTH UNIT (m, ft, fa, HR, pb)SPEED UNIT (kt, km/h, mph)WIND UNIT (kt, km/h, mph, m/s)TEMP UNIT (°C, °F)NAV DATA (OFF,    ,    ,    )KEY BEEP (OFF, ON)RINGS (OFF, ON)WAYPOINT MARK (OFF, ON)EBL REFERENCE (TRUE, RELATIVE)BEARING READOUT (TRUE, MAGNETIC)CURSOR POSITION (LAT/LON, RNG&BRG)TRIP SOURCE (LAT/LON, SPEED)WIND SPD/DIR (TRUE, APPARENT)SHIFT MODE (MANUAL, AUTO)AUTO SHIFT SPEED (1-99 (kts), 15)TX SECTOR BLANK (OFF, ON)BLANKING START (000-359°, 000°)BLANKING AREA (000-135°, 000°) LOCAL TIME SETUP (-13:30 - +13:30, 0:00)ANTENNA SPEED (24rpm, AUTO)RANGE nm, sm: 0.125, 0.25, 0.5, 0.75, 1, 1.5, 2, 3, 4, 6, 8, 12, 16, 24km: 0.25, 0.5, 0.75, 1, 1.5, 2, 3, 4, 6, 8, 12, 16, 24, 36SCANNER TEST (Tests antenna unit.)Turn on powerChoose GO TO RADAR SETUP from the INSTALLATION menu,and then go to page 4 of theSYSTEM menu.RADAR SETUPINSTALLATIONMENU
  SP-1SPECIFICATIONS 1. GENERAL 1.1  Indication System  PPI daylight display, raster scan, 4 tones in monochrome 1.2  Range, Pulselength (PL) & Pulse Repetition Rate (PRR) Range (nm) 0.125, 0.25, 0.5, 0.75 1, 1.5, 2  3, 4, 6, 8, 12, 16, 24, 32Pulse Length  0.08 µs (short)  0.3 µs (medium) 0.8 µs (long) Pulse Repetition Rate  3000 Hz nominal  1200 Hz nominal 600 Hz nominal 1.3  Range Resolution  18 m 1.4 Bearing Discrimination  5.2° 1.5  Minimum Range  20 m   1.6 Bearing Accuracy  Within 1° 1.7  Range Ring Accuracy  1.0 % of range or 8 m, whichever is the greater 2.ANTENNA UNIT 2.1 Radiator  Micro-strip 2.2 Polarization  Horizontal 2.3  Antenna Rotation Speed  24/31/41 rpm nominal (auto-select according to range) 2.4  Radiator Length  45 cm 2.5 Horizontal Beamwidth  5.2° typical 2.6 Vertical Beamwidth  25° 2.7  Sidelobe Attenuation  Less than -20 dB 3. TRANSCEIVER MODULE 3.1  Frequency  9410 MHz ±30MHz (X-band) 3.2 Modulation  P0N 3.3  Peak Output Power  2.2 kW 3.4  Modulator  FET Switching Method 3.5  Intermediate Frequency  60 MHz 3.6 Tuning  Automatic 3.7  Receiver Front End  MIC (Microwave IC) 3.8  Bandwidth  15 MHz (short pulse), 5 MHz (medium/long pulse) 3.9  Duplexer  Circulator with diode limiter 3.10 Warm-up Time  1-min. approx. 4. DISPLAY UNIT 4.1  Picture Tube  7” rectangular monochrome LCD 4.2  Display Pixels  240(H) x 320(V) dots,   Effective radar display area: 240x240 dots 4.3  Range, Range Interval, Number of Rings Range (nm/km) 0.125 0.25 0.5 0.75 1  1.5 2 3 4 6 8 12 16 24 32Ring Interval  0.0625  0.125  0.125 0.25 0.25 0.5 0.5 1 1 2  2  3  4  6 8Number of Rings  2  2  4  3  4  3  4  3 4 3  4  4  4  4 4    Range unit: nm/sm/km selectable, 0.125: nm/sm only, 32: km only
  SP-24.4  Markers  Heading Line, Bearing Scale, Range Rings,   Variable Range Marker (VRM), Electronic Bearing Line (EBL),   Tuning Bar, Cursor, Parallel Cursor, Alarm Zone,     Waypoint Mark*, North Mark* 4.5  Alphanumeric Indications Range, Range Ring Interval, Display Mode (HU),     Interference Rejection (IR), Variable Range Marker (VRM),     Electronic Bearing Line (EBL), Stand-by (ST-BY),   Guard Alarm (G (IN), G (OUT), UP RANGE), Echo Stretch (ES),     Range and Bearing to Cursor, Bearing or L/L Position,   Echo Tailing (TRAIL), Trailing Time, Trailing Elapsed Time,     Watchman (WATCHMAN), Zoomed Display (ZOOM),   Navigation Data*, Heading*    *: external data required 4.6  Input Sentences  IEC61162, NMEA0183 (Ver1.5/2.0) GGA, RMC, RMA, RMB,   GLL, VTG, VBW, VHW, HDT, HDG, HDM, BWR, BWC, GLC, GTD, DPT, DBK, DBS, DBT, MTW, ZDA, MWV, XTE 4.7  Output Sentences  IEC 61162, NMEA 0183 (Ver3.0) TLL (by key operation) 5. ENVIRONMENTAL CONDITIONS 5.1  Ambient Temperature  Antenna Unit: -25°C to +70°C, Display Unit: -15°C to +55°C 5.2  Relative Humidity  95% or less at +40°C 5.3 Waterproofing  Antenna Unit: IPX6    Display Unit: IPX5 (IPX0 when an external buzzer installed) 5.4  Bearing Vibration  IEC 60945 6. POWER SUPPLY   12-24 VDC: 3.2-1.4 A 7. COATING COLOR 7.1 Display Unit  N3.0 7.2  Scanner Unit  Cover: N9.5, Bottom: 2.5PB 3.5/10 8. COMPASS SAFE DISTANCE 8.1  Display Unit  Standard: 0.60 m  Steering: 0.40 m Scanner Unit  Standard: 1.25 m  Steering: 0.85 m

Navigation menu