Furuno Fm 8800D 8800S Users Manual

FM-8800D8800S to the manual 40544afb-e88c-4693-b79f-a70d6789e633

: Furuno Furuno-Fm-8800D-8800S-Users-Manual-429124 furuno-fm-8800d-8800s-users-manual-429124 furuno pdf

Open the PDF directly: View PDF .
Page Count: 69

Download
Open PDF In Browser	View PDF

VHF RADIOTELEPHONE
FM-8800D/8800S

PRINTED IN JAPAN

The paper used in this manual
is elemental chlorine free.

FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone :

0798-65-2111

Fax

0798-65-4200

:

All rights reserved.

Printed in Japan

FIRST EDITION : SEP. 2004
E

Pub. No. IME-56420-E
( TATA ) FM-8800D/S

: JUN. 15, 2006

*00014993204*
*00014993204*
*00014993204*

*IME56420E00*
*IME56420E00*
*IME56420E00*

SAFETY INSTRUCTIONS
CAUTION

WARNING

Attach securely protective
earth to the ship's body.

Hazardous voltage.
Can shock, burn or cause
serious injury.

The protective earth
(grounding) is required to the
AC/DC power supply unit to
prevent electrical shock.

Do not work inside the equipment unless totally familiar
with electrical circuits.
Do not approach the antenna
closer than 0.9 m (MPE by
FCC) when it is transmitting.

Confirm that the power supply voltage
is compatible with the voltage rating
of the equipment.

The antenna emits radio waves
which can be harmful to the
human body.

Connection to the wrong power supply
can cause fire or equipment damage.
The voltage rating appears on the label
at the rear of the display unit.

RF power density
Description
Distance
on antenna aperture
required by
100 W/m

FM-8800S

FM-8800D

2

10 W/m
2 W/m 2
100 W/m 2

0.11 m IEC 60945
0.33 m IEC 60945
0.9 m MPE by FCC
0.11 m IEC 60945

10 W/m 2
2 W/m 2

0.33 m IEC 60945
0.9 m MPE by FCC

2

(MPE: Minimum Permissible Exposure)

Turn off the power at the mains switchboard before beginning the installation.
Post a warning sign near the switchboard to indicate that power should not
be applied while the equipment is being
installed.
Electrical shock, serious injury or fire can
result if the power is not turned off or is
applied while the equipment is being
installed.

Observe the compass safe distance to
prevent deviation of a magnetic
compass.
Standard
compass

Steering
compass

FM-8800S

1.45 m

0.90 m

FM-8800D

1.45 m

0.95 m

IF-8810

0.85 m

0.55 m

IF-8820

0.75 m

0.50 m

HS-2003

1.50 m

0.95 m

HS-8800

0.40 m

0.30 m

RB-8800
(W/HS-8800)

1.20 m

0.80 m

1.50 m

1.00 m

0.90 m

0.60 m

RB-8810
(W/HS-8800)
PR-240-CE

i

TABLE OF CONTENTS
SYSTEM CONFIGURATION................................................................................ iii
EQUIPMENT LISTS ........................................................................................... iv
1. MOUNTING ................................................................................................... 1-1
2. CONNECTIONS ............................................................................................ 2-1
3. ASSEMBLING CONSOLE KIT ..................................................................... 3-1
PACKING LISTS ............................................................................................... A-1
OUTLINE DRAWINGS ...................................................................................... D-1
INTERCONNECTION DIAGRAMS ....................................................................S-1

ii

SYSTEM CONFIGURATION
VHF
Antenna

CH 70 RX
Antenna

VHF console
RC-8800

Wing handset MAX
2 sets
T/R AF output for VDR

Handset
HS-2003

Transceiver Unit

Junction
Box*
IF-8810

IEC61162-1 input
DSC information output
External alarm
Remote station
RB-8800/8810

FM-8800D
FM-8800S

DMC I/F
IF-8820

MAX
4 sets

RB-8800/8810

Printer
IF+UTP-80FK

Distress Message Controller
DMC-5
Printer
PP-510
PP-8800

100-115/200-230 VAC
50/60 Hz, 1φ
Radio Battery
24 VDC

AC/DC
Power Supply
Unit
PR-240-CE

Omit for Russian Version

External
Speaker
SEM-21Q

24 VDC

: Standard
: Optional

Category of units
Unit

Category

Antenna

Exposed to weather

All other units

Protected from weather

*: Option for FM-8800S/D-N

iii

EQUIPMENT LISTS
Standard Supply
Name

1

Transceiver Unit

Type
FM-8800D-E-A
FM-8800D-E-N
FM-8800D-F-A
FM-8800D-F-N
FM-8800S-E-A
FM-8800S-E-N
FM-8800S-F-A
FM-8800S-F-N
FM-8800S-R-A
FM-8800S-R-N

Qty

1

FP05-05700
2

Accessories*

4
5

Junction Box
Installation
Materials*
Spare Parts*

Remarks
D: Duplex
S: Simplex
E: With handset
HS-2003
F: With microphone
DM-2003-F
A: With IF-8810
N: No IF-8810
R: Russian version

—

000-054-228
1

FP05-05710
3

Code No.

000-054-156

IF-8810

1

—

CP05-09900

1

000-054-227

SP05-05501

1

005-377-820

For E-type
Handset HS-2003,
Hanger FP05-05510,
Others FP05-05511
For F-type
Microphone DM-2003-F
For A-type
Power cable 05S9371,
CP05-09901

Standard Supply for VHF Console
1

Name
VHF Console

Type
RC-8800-SN
RC-8800-DN
RC-8800-SA
RC-8800-DA

Qty
1

Code No.
—

2

Installation
Masteries*

CP05-10201

1

005-371-850

3

Accessories*

FP05-05800

1

000-054-372

5

Spare Parts*

SP05-05501

1

005-377-820

Remarks
D: Duplex FM-8800D
S: Simplex DM-8800S
N: No printer
A: With printer & I/F board

Handset HS-2003 &
Handset hanger FP05-05510

*: See lists at the end of this manual.

iv

EQUIPMENT LISTS

Optional Equipment
Name

Type

Code No.

Remarks

Flush Mount Kit

OP05-102

Junction Box

IF-8810

—

W/ Screw 5x20 4 pcs.

DMC Interface

IF-8820
RB-8800-15
(W/ 1.5 m Cable)
RB-8800-20
(W/ 2 m Cable)
RB-8810-15
(W/ 1.5 m Cable)
RB-8810-20
(W/ 2 m Cable)
HS-8800-15

—

No use for Russian version

—

·FP05-05701*,
·Handset HS-8800,
·Hanger W/DIST. button HG-8800

—

·FP05-05511*,
·Handset HS-8800,
·Hanger HG-8810

000-054-230

W/ 1.5 m Cable

HS-8800-20

000-054-171

W/ 2 m Cable

HS-8800-W-35

000-054-287

Waterproof

HS-2003-15

000-054-223

W/ Cable 1.5 m

HS-2003-20

000-XXX-XXX

W/ Cable 2.0 m

HS-2003-50S

000-XXX-XXX

W/ Straight cable 5.0 m

HS-6000FZ11

000-135-072

HG-8800

000-054-229

For HS-8800

HG-8810

000-054-231

For HS-8800

FP05-05510

005-951-790

For HS-2003

AP-102

000-580-019

For HS-6000FZ11

Loudspeaker

SEM-21Q

000-144-917

Dynamic Mic. Set

OP05-57

000-045-775

Carbon Mic. Set

OP05-58

000-045-776

Handset set

OP05-42

000-045-778

Mic. Receptacle Box
Microphone

RBD-VHF (B)

000-056-094

DM-2003-F

005-377-760

Printer

PP-510

—

Printer Interface

IF-8500

—

AC-DC Power Supply

PR-240-CE

—

Remote Station

Handset

Handset Hanger

Antenna Material

000-054-120

AP05-00800

000-057-721

AP05-00810

000-057-722

AP05-00900

000-057-739

AP05-01000

000-054-123

Handset HS-6000FZ5,
Receptacle RDB-VHF(B),
Hanger AP-102
Handset HS-6000FZ6,
Receptacle RDB-VHF,
Hanger AP-102
Handset HS-6000FZ11,
Receptacle RDB-VHF(B),
Hanger AP-102

Whip antenna FAB-151D,
Mounting plate 4-310071,
Coax. Cable 5D-2V 10m,
Connector M-P-5 2 PCS
Whip antenna RA106,
Mounting plate RA115,
Coax. Cable 05S9104 5m
Whip antenna 396-1,
Mounting plate 4187
Whip antenna FAB-151D,
Mounting plate 4-310071,
Connector M-P-7 2 PCS
*: See lists at the end of this manual

v

EQUIPMENT LISTS

Name

Antenna Material

Signal Cable

Twisted Cable

VHF Console Kit

Type
AP05-01100

000-054-224

AP05-01200

000-054-232

AP05-01210

000-054-233

05S0309 *10M*

000-106-043

Whip antenna 150M-W2VN,
Coax. Cable 5D-2V 10m,
Connector M-P-5 2 PCS
Whip antenna FAB-151D,
Mounting plate 4-310071,
Coax. Cable 5D-2V 10m,
Connector M-P-5 & M-P-7
Whip antenna FAB-151D,
Mounting plate 4-310071,
Coax. Cable 5D-2V 20m,
Connector M-P-5 & M-P-7
10m

05S0309 *20M*

000-106-044

20m

05S0309 *30M*

000-106-046

30m

05S0309 *40M*

000-106-047

40m

05S0309 *50M*

000-106-048

50m

000-111-680

5m

000-120-792

10m

000-120-793

15m

000-120-794

20m

CO-SPEVV-SB-C
0.2x2P

000-120-214

30m

RC-8800-N-75BG

000-054-125

Without Printer

RC-8800-A-75BG

000-054-126

With Printer

Printer

PP-8800

-

Emergency lamp

EMG-1T

000-138-378

vi

Remarks

Code No.

W/ power cable
For rack console, cable attached

1.

MOUNTING

Transceiver Unit
General mounting considerations
Determine the mounting location for the transceiver unit considering operator convenience,
proximity to the power source and the ground location. Keep these and the following points
in mind when selecting a mounting location.

• Locate the unit in a place free of water spray and water splash.
• Keep the unit out of direct sunlight because of heat that can build up inside the unit.
• Leave a little slack in cables to allow a service technician to move the radio from its usual
location with the cables connected. This lets him make tuning and other adjustments on a
“live” set.
• Do not install the unit where flammable gases are stored.
• Select a well-ventilated area.
• Ensure the mounting location is strong enough to support the weight of the unit (approx. 6
kg) under the condition of continued vibration normally encountered aboard the vessel. If
necessary, reinforce the mounting area with a doubling plate or lining block.
• Leave sufficient space at the sides and rear of the unit for maintenance and service
purposes and to provide for circulation of cooling air. See outlines drawings at the back of
this manual.
• For flush mounting, select a location where the LCD can be easily viewed.
• The transceiver unit will affect a magnetic compass if placed too near the compass.
Observe the compass safe distance to prevent deviation of a magnetic compass,
referring to page “ i ”.
Note: Take great care not to press the DISTRESS switch during the installation. If you
accidentally press the switch, immediately turn off the equipment and contact
appropriate authority by telephone.

1-1

1. MOUNTING

Overview of mounting methods

Keep pressed for 4 s in case of DISTRESS.
The alert is transmitted with steady lighting.

DISTRESS

1

2

4 IntCom
GHI

ALM STOP

CALL

Keep pressed for 4 s in case of DISTRESS.
The alert is transmitted with steady lighting.

DISTRESS

1

2

4 IntCom
GHI

ALM STOP

MSG

7

INTL

USA

PQRS

SHIFT

*

CANCEL

CALL

ABC

5

ACK

8

SCAN

0

HI/L0

JKL

TUV

3

6

9

#

TEST
DEF

USA

SHIFT

ABC

5

ACK

8

SCAN

0

HI/L0

JKL

TUV

3

6

9

#

TEST
DEF

PRINT
MNO

DW
WXYZ

LOG

CH16

FILE

MENU

ENT

FILE

MNO

DW

INTL

PQRS

CH16

PRINT

WXYZ

MSG

7

*

CANCEL

MENU

LOG

ENT

Overhead

Tabletop

Keep pressed for 4 s in case of DISTRESS.
The alert is transmitted with steady lighting.

DISTRESS

1

2

4 IntCom
GHI

7

ALM STOP

CALL

MSG

Flush Mount

INTL

USA

PQRS

SHIFT

*

CANCEL

ABC

5

ACK

8

SCAN

0

HI/L0

JKL

TUV

3

6

9

#

TEST
DEF

PRINT
MNO

DW
WXYZ

LOG

CH16

FILE

MENU

ENT

Bulkhead

Overview of mounting methods

1-2

1. MOUNTING

Mounting procedure for tabletop, overhead and bulkhead mounting
1. Using the hanger as a template, mark fixing holes in the mounting location.
2. Fix the hanger to the mounting location with self-tapping screws and washers (supplied).
(For added support, use nuts, bolts and washers instead of self-tapping screws.)
3. Screw the knob bolts with washers into the transceiver unit.
4. Set the transceiver unit to the hanger and tighten knob bolts.
265

251
Keep pressed for 4 s in case of DISTRESS.
The alert is transmitted with steady lighting.

1

DISTRESS

110

2

ABC

3 TEST
DEF

4 IntCom

5 ACK

6 PRINT

INTL

8 SCAN

9 DW

0 HI/L0

#

GHI

JKL

MNO

CH16

FILE

ALARM
CANCEL

7

ALM STOP

SQL

VOL/PWR

CH

CALL

SHIFT

MSG

OFF

TUV

*

HANDSET

USA

PQRS

WXYZ

LOG

MENU

ENT

ＰＵＳＨ ＴＯ ＥＮＴＥＲ

AUTO

Keep pressed for 4 s in case of DISTRESS.
The alert is transmitted with steady lighting.

DISTRESS

1

2

4 IntCom
GHI

ABC

5

ACK

8

SCAN

0

HI/L0

JKL

3

6

TEST
DEF

PRINT
MNO

CH16

FILE

ALARM
7

ALM STOP

HANDSET

SQL

VOL/PWR

CH

CALL

MSG

OFF

AUTO

INTL

USA

PQRS

SHIFT

*

100

CANCEL

TUV

9

#

DW
WXYZ

LOG

MENU

100

ENT

ＰＵＳＨ ＴＯ ＥＮＴＥＲ

• All dimensions in millimeters.
• Leave sufficient space at the sides and rear of the unit to provide easy access for
maintenance and service.
Mounting dimensions for tabletop, overhead and bulkhead mounting

1-3

1. MOUNTING

Mounting procedure for flush mount (option)
Requires optional flush mount kit OP05-102 (Code No. 000-054-120). Prepare a cutout in
the mounting location whose dimensions are as shown in the figure below.
Flush mount kit OP05-102
Name
1 Mounting plate
2 Self-tapping screw
3 Hex screw

Code No.
100-323-160
000-802-081
000-882-075

Qty
1
4
2

#150

251

260 ± 1
280 ± 1
277 ± 0.5

122 ± 0.5

244

105 ± 1
30 ± 1

20
14 27

Type
05-093-1211
5x20
M8x16

Pilot holes (4 pcs.)

Mounting dimensions for flush mount

VHF Antenna
The antenna requirements
Any good quality antenna meeting the requirements shown below may be used. A high-gain
antenna is preferable.

• Frequency range:

155 to 164 MHz

• Impedance:

50 ohms

• Polarization:

Vertical

• Handling power:

30 W/ min

• Quality:

Able to withstand marine environment

Mounting considerations
• The antenna should be well separated from nearby antennas, masts, and other interfering
objects.
• The higher the antenna is mounted above the horizon, the further the communications
range.

Mounting procedure
The basic mounting procedure for antennas supplied by FURUNO is as follows, however
consult appropriate outline drawing for details.
1. Fasten the antenna bracket to the stanchion.
2. Set the antenna to the antenna bracket and tighten bolts.
3. Screw the coaxial cable plug into the antenna.

1-4

1. MOUNTING

CH70 RX Antenna
The antenna should be well separated from nearby antennas, masts, and other interfering
objects.
The mounting procedure is the same as that for the VHF antenna, however consult
appropriate outline drawing for details.

Handset Hanger
The handset hanger can be mounted at the left side of the transceiver unit. The mounting
location should provide easy access to front panel controls while operating the handset.
Also, the length of the standard handset cable is 50 cm, so locate the handset hanger within
50 cm of the unit. (Longer cables are available optionally.)

Power Supply (option)
For Convention vessels, both AC and DC power must be fed to the FM-8800D/8800S, via
an AC/DC power supply. When AC input fails, DC power is supplied. FURUNO can supply
an AC/DC power supply unit, the PR-240-CE.

Mounting considerations
When selecting a mounting location, keep in mind the following points.

• Select a location which provides adequate ventilation.
• The location must be clean and dry.
• The mounting location must be able to support the weight of the unit (14.5 kg) under the
continued conditions of vibration normally encountered aboard the vessel. If necessary,
reinforce the mounting location.
• The PR-240-CE will affect a magnetic compass if it is placed to near the compass.
Observe the compass safe distance to prevent deviation of a magnetic compass,
referring to page “ i ”.

Mounting
Refer to outline drawing.

1-5

1. MOUNTING

Printer (option)
Printer PP-510
To mount the printer, refer to the printer outline drawing at the back of this manual.
1. Select a flat surface.
2. Fix the mounting base to the mounting location with four screws (supplied).
3. Lay the printer on the top of the mounting base and fasten it with the mounting fixtures
(two at each side and one at rear).

Mounting Fixture

Mounting Fixture

Mounting Dimensions 300 (H) x 396 (W) mm

Mounting of Printer PP-510

Printer PP-8800
The printer PP-8800 is flush-mounted in a panel. Refer to the outline drawing at the back of
this manual.
1. Make a cutout of 208(w) x 118(h) mm.
2. Set the printer and fix it with four self-tapping screws (4x16).

Printer Interface (option)
The printer interface IF-8500 is required for the printer PP-510 which is commonly used with
the FM-8800D/S and other MF/HF radio communication equipment. To mount the unit, see
the outline drawing at the back of this manual.

External Loudspeaker (option)
The external loudspeaker can be installed on a tabletop, the overhead or a bulkhead.
Fasten the loudspeaker to the mounting location with self-tapping screws, or nuts, bolts and
washers. For mounting dimensions, see the outline drawing at the back of this manual.

1-6

1. MOUNTING

Junction box IF-8810/ DMC interface IF-8820
Note: DMC interface IF-8820 is not used for Russian version.
To install the remote box RB-8800/RB-8810, wing handset, etc., the junction box IF-8810 is
required. Install the junction box near the transceiver unit. Approx. 3 m cable is preattached
to the junction box to connect to the transceiver unit.
To connect Furuno’s distress message controller DMC-5, the DMC interface IF-8820
(option) is required.
1. Open the cover.
2. Mount the unit with four self-tapping screws (5x20).

240

100

Note: This plug is not
fitted in IF-8820.

Fixing holes 5mm dia.
Mounting the junction box/DMC interface

1-7

1. MOUNTING

Remote station RB-8800/RB-8810 (option)
Up to four remote stations can be connected in a daisy chain.
Note: For the remote station RB-8800, there are two method of cable entry: bottom-side entry
and rear-side entry. For rear-side entry, make one or two holes of more than 12 mm diameter.
For last station in the daisy chain, just one cable entry hole is needed.
1. Remove screws on the handset hanger (four for RB-8800, six for RB-8810).
2. Remove upper chassis of the hanger.
3. Mount the base of the hanger to a bulkhead with self-tapping screws 4x20 (four for
RB-8800), or 4x16 (two for RB-8810).
4. After connecting cables, assemble the remote station.
5. For RB-8800, attach blind seals on the screws.

Cover of handset hanger

63

Handset hanger
HG-8800

20 30

33

Screws 4 pcs.
Attach blind seal
on the screws.

40

Nameplate

DISTRESS

Cable entry
(Rear)

140± 0.5

φ 12

Handset
HS-8800

φ 12

Cable entry

77

VOLUME

#150

4- φ4.5

Fixing holes
40 ± 0.5 40 ± 0.5

Cable entry
(Bottom)

Remote station RB-8800
Hanger
HG-8810
(77)

Handset
HS-8800

57

22

145 ± 0.5

208

(208)
#150

φ12, Cable entry

Nameplate

2- φ4.5

Fixing hole
Hanger

Hanger mounting base

Remote station RB-8810

1-8

42

Cable entry

65

1. MOUNTING

Outdoor mounting of RB-8810
Remote station RB-8810 with waterproof-type handset HS-8800-W-35 can be mounted
outdoors. The hanger should be coated as directed below with silicone sealant for
waterproofness.
1. Fix the mounting base with self-tapping screws. Coat exposed part of these screws with
silicone sealant.
2. Attach the cable from the transceiver unit or junction box. Coat cable around cable
entrance with silicone sealant
3. Fix the cover of the handset hanger. Coat junction between mounting base and cover
with silicone sealant.

2. All around the cable
at cable entry

Self-tapping screws

3. All around the junction
coating parts

Note: Confirm that plastic washers are
in screw holes before fixing cover.

1-9

1. MOUNTING

VHF console
Install the rack console where the equipment can be easily operated, checked and serviced.
Consult with shipyard personnel and ship's officer-in-charge to determine best location. The
location must satisfy the following points:
• Select a location where controls can be easily operated.
• Select a location where shock and vibration are minimal.
• Locate the console away from water splash and rain.
• The temperature and humidity of the location should be both stable and moderate.
Fixing
1. Ask shipyard personnel to tighten six M5 nuts or six M5 bolts to the fixing holes (on the
wall), referring to the outline drawing at the back of this manual.
2. Detach the cover assembly from the console.
3. Hang VHF console on bolts.
4. Screw the console with the bolts or nuts tightly.
5. Attach the cover assembly to the console.
Note: When you connect wires as soon as attaching console, refer to paragragh 2-10.
6. Attach the handset hanger with two screws.
7. To attach the optional emergency lamp, connect the cable to the terminal board, and
then attach the lamp to the console. Refer to the interconnection diagram and out line
drawing.

(371)

EMG-1T
EMERGENCY LAMP

190

°
75

(371)
330

145

480

(500)

30

298 ± 0.5

1-10

FIXING HOLES

TERMINAL BOARD
(266)

#50

CABLE ENTRY
(REAR)
250

30

40

170 ± 0.5

170 ± 0.5

40

HANDSET HANGER

2.

CONNECTIONS

Overview
The figure below shows where to connect various equipment at the rear of the transceiver
unit.
ANT
Connects antenna.

Ground terminal.

24VDC
Connects power
cable.

PRINTER
Connects printer
PP-510.

IEC61162-1 (NMEA)/REMOTE
Connects junction box IF-8810.

EXT SP
Connects external
loudspeaker.

CH70 RX ANT
Connects DSC
antenna here.

FM-8800D/8800S, rear view

Connection of Power Supply
Convention vessels, 100/220 VAC ship’s mains
Convention vessels must supply both AC and DC power to the FM-8800D/8800S, via an
AC/DC power supply unit. Both AC and DC are supplied by the AC/DC power supply unit,
and when AC input fails DC power is activated.
Connect the radio battery to the DC IN terminal on the PR-240-CE. Connect the AC ship’s
mains to the AC IN terminal on the PR-240-CE.

Radio battery (24 VDC)
Attach the connector supplied to the power cable and plug it into the 24VDC connector at
the rear of the transceiver unit. Connect the wire ends to the radio battery line.

2-1

2. CONNECTIONS

Connection of VHF Antenna
The VHF antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type
5D-2V. Be sure to leave some slack in the cable for future service and maintenance.
Lay the coaxial cable and attach an M-type plug to the cable (if necessary) as follows.
1.
2.
3.
4.
5.

Remove the sheath by 20 mm.
Bare 13 mm of the center conductor. Trim braided shield by 5 mm and tin.
Slide coupling ring onto cable.
Screw the plug assembly on the cable.
Solder plug assembly to braided shield through solder holes. Solder contact sleeve to
conductor.
6. Screw coupling ring into plug assembly.
7. Screw the plug into the ANT connector at the rear of the transceiver unit.

How to attach the M-type plug to the coaxial cable

2-2

2. CONNECTIONS

Connection of DSC Antenna
The DSC antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type
5D-2V. Attach an M-type plug to the cable (if necessary) as shown an page 2-2. Screw the
plug into the CH70 RX ANT connector at the rear of the transceiver unit.

Connection of Handset
Connect the handset cable to the HANDSET connector on the front panel.

Grounding the Transceiver Unit
Fasten a ground wire (local supply) between the GND terminal at the rear of the transceiver
unit and ship’s hull (or ground bus).

Connecting the Junction Box
The junction box is required to connect a remote station, wing handset, etc. The cable to be
connected with the transceiver unit is prefitted on the junction box at the factory. For
connection of other cables, see the interconnection diagram.

Cable entry

Clamp the cable with
U-type cable clamps.

Use one of these nuts for ground terminal between JB and ship's body.

Cable clamp: Clamp shield part of the cables to ground cables.

2-3

2. CONNECTIONS

Connecting the Remote Station without the Junction
Box
The remote station (or DMC Interface, Mic. Receptacle box, etc) can be connected directly
to the transceiver unit, using the D-sub connector supplied as installation materials.
Attach the connector to the cable as follows.

Shield tape (metal)
Fold back the armor,
and then wind the shield
tape along the edge of cable.

Cable clamp
Cable

Connector XM2A-3701 &
Housing case XM2S-3712

Attachment of connector

When the handset HS-2003 is not connected to the
Transceiver unit
When the handset HS-2003 is not connected to the transceiver unit, i.e.,always the remoted
handset is used, the following modification is necessary.
1. Dismount the cover of the transceiver unit by removing four screws at the rear panel and
two screws at the side.
2. Dismount the bottom cover by removing seven screws.

J15

CPU board
05P0773

3. Shorten between #1 and #2 of J15. The handset line of the HANDSET port becomes
always “ON HOOK”.
4. Assemble the unit.

2-4

2. CONNECTIONS

Connection of AC/DC Power Supply Unit PR-240-CE
The power supply PR-240-CE is shipped ready for connection to a 200-230 VAC ship’s
mains. If the ship’s mains is 100 VAC – 115 VAC, change the tap connection and terminal
board connection as below. Attach label supplied as accessories to the punch mark in the
front panel according to the ship’s mains.
Ship’s mains

Tap connection

Terminal board
connection #1 & #2

100-115 VAC

SEL 115 V

b

200-230 VAC

SEL 230 V

a

100-115 VAC

200-230 VAC
1

White

1

White

2

Black

2

Black

3

3
Punch mark
(a)

(b)

Front

SEL
115 V

1
2
3
4
5
6
7
8

SEL
230 V

Terminal board connection

Heat sink

Tap connection (Pull out to disconnect)

Top view of AC/DC power supply unit (cover removed)

2-5

2. CONNECTIONS

Protective earth
Connect IV-2.0sq wire between ship’s superstructure and the ground terminal on the
PR-240-CE.

CAUTION
Attach protective earth
securely to the ship's body.
The protective earth
(grounding) is required for the
AC/DC power supply unit to
prevent electrical shock.

Attach a label here.

GND terminal

PR-240-CE Front panel

2-6

2. CONNECTIONS

Jumper Setting for Termination
Note: DMC interface is not used for Russian version.
It is necessary, for termination, to change the jumper setting for remote station or DMC
interface.
Open the unit(s) terminated and change the jumper plugs J2 and J3 to ON position (#2-#3).
(Default setting is OFF position.)
Transceiver
Unit

Junction
Box

Remote
Station

Remote
Station

DMC I/F

Remote
Station

Remote
Station

Remote
Station

Terminated Unit

Note that up to four remote stations can be connected.
LINE
TERMINATION
J3

DISTRESS

1

ON

RS-485
TERMINATION
J2

3

1

ON

3

J1

Set to ON (#2-3)
for termination.

05P0782
TB1

VOLUME

TB2

Remote station RB-8800
Cable entry
TB1
TB2
J3

3
3

ON OFF

1 J2

RS-485
TERMINATION

LINE
TERMINATION

ON OFF

1

05P0798

2- φ 4.5

Set to ON (#2-3)
for termination.

J1

Fixing hole

Remote station RB-8810

2-7

2. CONNECTIONS

Remove four screws
to open the unit.

Set jumper plug to ON (#1-2).

05P0778
J4
ON

RS-485
TERMINATION

TB1

DMC Interface IF-8820

2-8

2. CONNECTIONS

2.10

Wire connection of VHF console

1. Remove the cover assembly and printer assembly (or concealing lid) form the console.
For the printer assembly, remove the cables connected at the Transceiver Unit and the
terminal board.
Cover assembly
Binding screw F
M4X10 8 places
Binding screw F
M4X10 4 places

Printer assembly
or Concealing lid

Console

Terminal board

2. Connect the power cable from the ship to the terminal block 1 (+) and 2 (-).
Terminal Board Wiring
1. Wiring conductor

9∼10mm
2. Wiring
1)Insert a screwdriver which blade edge
is 3.5 X 0.5mm to the square hole.
2)Press the screwdriver to arrow direction
to open the spring in the round hole.
3)Insert the wire to the round hole.
4)Remove the screwdriver.

Power cable
from the ship

1 2

1 2 3 4 5 6 7 8

-

Square hole

Round hole

Terminal board

3. Connect the ground wire from ship to each ground terminal for the transceiver unit and
the junction box.
4. Connect cables from external equipments to the junction box.
5. Fix the printer assembly (or concealing lid) and the cover assembly.

2-9

2. CONNECTIONS

This page is intentionally left blank.

2-10

3.

ASSEMBLING CONSOLE KIT

A VHF console kit is required to mount the Transceiver Unit in the field. There are two types
as shown below.
VHF console kit
Type
RC-8800-N-75BG
RC-8800-A-75BG

Code No.
000-054-125
000-054-126

Remarks
Without printer
With printer

Assembling the Console Kit
1. Remove the cover assembly, the panel assembly and the printer assembly (or
concealing lid) from the console. For the printer assembly, remove the cable connected
to the terminal board.
Cover assembly
Binding screw F
M4X10
8 places
Binding screw F
M4X10
4 places
Printer assembly
(or Concealing lid

#
#

Remove screws( )and
detach the panel assembly.

Console

Panel assembly

3-1

2. Fix the panel assembly to the Transceiver Unit with binding screws (use original binding
screws of the Transceiver Unit). Refer to the figure below.
3. Screw in hex bolts M8x16 and flat washers loosely at both sides of the Transceiver Unit.
Panel assembly

Binding screw M4 2 places
(Use the original screws
of the Transceiver Unit.)

Washer M8
2 places

Hex bolt M8X16
2 places

(faster loosely)

4. Set the Transceiver Unit to the console, remove the grommets from the console and fix
the Transceiver Unit with hex bolts using the holes formerly occupied by the grommets.

Hex head screws

Mounting of
the Transceiver Unit

Insert console upside down. Close the hole with grommets
lastly.

Connecter
Connecter

Mounting
plate
Transceiver
Unit

Flat washer

Fix Mounting Plate
between washers.

5. Connect connector from the fuse to the power connector derived from the Transceiver
Unit.

3-2

6. Replace the cable attached to junction box with the cable (55 cm, 37-pin D sub) supplied
with the console kit.
Replace the original cable
with the cable assembly
DSUB37M-PHX3-L550.

A

Junction box
(without cover)
PH Connector
10P

PH Connector
12P

J3

J2

J1

PH Connector
14P

2

3

Crimp-on lug
A View

7. Connect the cable (37-pin D sub) attached to the junction box to the Transceiver Unit
and then mount the junction box on the console.
±Binding screw F
M4X8  4 places

Cover

±Screw B
M4X10 4 places

Mounting plate

3-3

Junction box
Grommets 2 places

8. For the console w/printer, connect the printer cable for data transmission to the
PRINTER port of the Transceiver Unit and fix the power cable to the terminal board as
before. Then, fix the printer assembly to the console. For no printer, fasten the
concealing lid to the console.

Printer
Printer cable

W/ Printer

J2

Insert the mounting plate
for printer to the catch of the console

View

9. Fasten the cover assembly.
NOTE: If the console assembly is to be mounted on the hull, refer to paragraghs 1-9 and
2-10.

3-4

OUTLINE

INSTALLATION MATERIALS

ACCESSORIES

SPARE PARTS

UNIT

005-377-800

000-151-711
CP05-09901

05S9371-0

005-951-920

005-951-790
FP05-05511

000-054-223
FP05-05510

HS-2003

005-377-820

SP05-05501

1

Q'TY

1

1

CP05-09900

1

1

1

FP05-05700

1

SP05-05501

000-054-225 **

FM-8800S/D

DESCRIPTION/CODE №

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

DOCUMENT

DISTRESS PROCEDURE

遭難通信要領書

OPERATOR'S MANUAL

取扱説明書

INSTALLATION MANUAL

装備要領書

OPERATOR'S GUIDE

VHF/MF DISTRESS ALERT
FLOW
操作要領書

遭難警報ﾌﾛVHFMF*

図書

NAME

FM-8800S-J/E-N/FM-8800D-J/E-N

ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表型式/ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.

INSTALLATION MATERIALS

工事材料

CABLE ASSY.

ｹｰﾌﾞﾙ組品

工事材料

ACCESSORIES

付属品

BRACKET FOR HANDSET

ﾊﾝﾄﾞｾｯﾄﾊﾝｶﾞｰ組品

HANDSET

ﾊﾝﾄﾞｾｯﾄ

付属品

SPARE PARTS

予備品

予備品

TRANSCEIVER UNIT

送受信機

ユニット

NAME

ＰＡＣＫＩＮＧ ＬＩＳＴ
OUTLINE

000-149-935

000-149-930 **
TIC-56420-*

000-149-932 **
OM*-56420-*

000-149-934 **
IM*-56420-*

000-809-270
OS*-56420-*

*52-00101-*

1

1

1

1

1

Q'TY

1/1

05EC-X-9851

DESCRIPTION/CODE №

05EC-X-9851 -4

A-1

NAME

OUTLINE

INSTALLATION MATERIALS

ACCESSORIES

SPARE PARTS

UNIT

005-377-800

CP05-09901

000-054-223

005-951-790
HS-2003

005-951-920
FP05-05510

FP05-05511

005-377-820

SP05-05501

000-054-219

1

1

1

Q'TY

1

CP05-09900

1

1

1

FP05-05700

000-054-166 **
IF-8810

FM-8800S*/D*

DESCRIPTION/CODE №

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

DOCUMENT

INSTALLATION MANUAL

装備要領書

OPERATOR'S MANUAL

取扱説明書

OPERATOR'S GUIDE

操作要領書

DISTRESS PROCEDURE

VHF/MF DISTRESS ALERT
FLOW
遭難通信要領書

遭難警報ﾌﾛVHFMF*

図書

OUTLINE

INSTALLATION MATERIALS

INSTALLATION MATERIALS

工事材料

工事材料

CABLE ASSY.

ｹｰﾌﾞﾙ組品

NAME

FM-8800S-J/E-A/FM-8800D-J/E-A、FM-8800S-J/E-AHK/FM-8800D-J/E-A-HK

ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.

INSTALLATION MATERIALS

工事材料

工事材料

HANDSET

ﾊﾝﾄﾞｾｯﾄ

BRACKET FOR HANDSET

ﾊﾝﾄﾞｾｯﾄﾊﾝｶﾞｰ組品

ACCESSORIES

付属品

付属品

SPARE PARTS

予備品

予備品

JUNCTION BOX

ｾﾂｿﾞｸﾊﾞｺ

TRANSCEIVER UNIT

送受信機

ユニット

ＰＡＣＫＩＮＧ ＬＩＳＴ
1/1

1

Q'TY

000-149-932 **

000-149-930 **
IM*-56420-*

000-149-934 **
OM*-56420-*

1

1

1

1

1

1

CP05-08701

000-149-935 **
OS*-56420-*

000-809-270
TIC-56420-*

*52-00101-*

005-949-280

CP05-08701

000-151-711

05S9371-0

DESCRIPTION/CODE №

05EC-X-9856 -3

05EC-X-9856

A-2

DOCUMENT

000-149-932

000-809-270
IM*-56420-*

*52-00101-*

005-377-800

000-151-711
CP05-09901

05S9371-0

005-377-760

DM-2003-F

005-377-820

SP05-05501

000-054-225 **

FM-8800S/D

1

1

Q'TY

1

1

1

1

CP05-09900

1

FP05-05710

DESCRIPTION/CODE №

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

DISTRESS PROCEDURE

遭難通信要領書

OPERATOR'S GUIDE

操作要領書

OPERATOR'S MANUAL

取扱説明書

NAME

FM-8800S-F-N/FM-8800D-F-N

CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.

INSTALLATION MANUAL

装備要領書

VHF/MF DISTRESS ALERT FLOW

遭難警報ﾌﾛVHFMF*

図書

OUTLINE

INSTALLATION MATERIALS

ACCESSORIES

SPARE PARTS

UNIT

INSTALLATION MATERIALS

工事材料

CABLE ASSY.

ｹｰﾌﾞﾙ組品

工事材料

MICROPHONE

ﾏｲｸﾛﾌｫﾝ箱詰品

付属品

SPARE PARTS

予備品

予備品

TRANSCEIVER UNIT

送受信機

ユニット

NAME

ＰＡＣＫＩＮＧ ＬＩＳＴ
OUTLINE

05EC-X-9858

000-149-935

000-149-934
TIC-56420-*

000-149-930
OS*-56420-*

OM*-56420-*

DESCRIPTION/CODE №

05EC-X-9858 -2
1/1

1

1

1

Q'TY

A-3

NAME

INSTALLATION MATERIALS

005-949-280

CP05-08701

005-377-800

000-151-711
CP05-09901

05S9371-0

005-377-760

DM-2003-F

005-377-820

SP05-05501
1

1

1

Q'TY

1

1

1

CP05-09900

1

FP05-05710

000-054-225 **

000-054-219
FM-8800S/D

IF-8810

DESCRIPTION/CODE №

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

NAME
DOCUMENT

DISTRESS PROCEDURE

遭難通信要領書

OPERATOR'S GUIDE

操作要領書

OPERATOR'S MANUAL

取扱説明書

INSTALLATION MANUAL

VHF/MF DISTRESS ALERT
FLOW
装備要領書

遭難警報ﾌﾛVHFMF*

図書

FM-8800S-F-A/FM-8800D-F-A

CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.

INSTALLATION MATERIALS

工事材料

工事材料

OUTLINE

INSTALLATION MATERIALS

ACCESSORIES

SPARE PARTS

UNIT

INSTALLATION MATERIALS

工事材料

CABLE ASSY.

ｹｰﾌﾞﾙ組品

工事材料

MICROPHONE

ﾏｲｸﾛﾌｫﾝ箱詰品

付属品

SPARE PARTS

予備品

予備品

TRANSCEIVER UNIT

送受信機

JUNCTION BOX

ｾﾂｿﾞｸﾊﾞｺ

ユニット

ＰＡＣＫＩＮＧ ＬＩＳＴ
OUTLINE

1/1

000-149-935

000-149-934
TIC-56420-*

000-149-930
OS*-56420-*

000-149-932
OM*-56420-*

000-809-270
IM*-56420-*

*52-00101-*

1

1

1

1

1

Q'TY

05EC-X-9859

DESCRIPTION/CODE №

05EC-X-9859 -2

A-4

A-5

ＰＡＣＫＩＮＧ ＬＩＳＴ

05EC-X-9857 -1

1/1

DM-2003-F
N A M E
ﾏｲｸｾｯﾄ

O U T L I N E

DESCRIPTION/CODE №

Q'TY

MICROPHONE SET
ZIRXXCDM002

ﾌｯｸ

1
HOOK
000-150-017
KON-003

ﾏｲｸﾛﾌｫﾝ

1
MICROPHONE
000-150-016

（略図の寸法は、参考値です。

DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

05EC-X-9857

A-6

CODE NO.

005-377-800

TYPE

CP05-09901

05EC-X-9401 -2
1/1

工事材料表
INSTALLATION MATERIALS
番 号
NO.

名  称
NAME

型名／規格
DESCRIPTIONS

1

CABLE ASSY.
CODE NO.

1
000-145-423

XM2A-3701

ｺﾈｸﾀ(XM2)

1

CONNECTOR
CODE NO.
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1種

4

Used only Japan

000-151-748

HOUSING CASE
CODE NO.

3

用途／備考
REMARKS

XM2S-3712

ｺﾈｸﾀﾌｰﾄﾞ(XM2)
2

数量
Q'TY

L-420

ﾐﾆﾋﾟﾝ組品(1)
1

略  図
OUTLINE

000-145-424

6X20 SUS304
5

SELF-TAPPING SCREW
CODE NO.

000-802-084

05EC-X-9401
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

A-7

CODE NO.

005-949-280

TYPE

CP05-08701

05DY-X-9417 -0
1/1

工事材料表
INSTALLATION MATERIALS
番 号
NO.

名  称
NAME
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1種

1

略  図
OUTLINE

型名／規格
DESCRIPTIONS

数量
Q'TY

用途／備考
REMARKS

5X20 SUS304
4

SELF-TAPPING SCREW
CODE NO.

000-802-081

05DY-X-9417
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

A-8

CODE NO.

005-951-920

TYPE

FP05-05511

05DZ-X-9502 -0
1/1

付属品表
ACCESSORIES
名  称
NAME

番 号
NO.

CODE NO.

2

用途／備考
REMARKS

2

SELF-TAPPING SCREW

ﾎﾟﾘｶﾜｯｼｬｰ

数量
Q'TY

4X16 SUS304 1ｼｭ

+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
1

型名／規格
DESCRIPTIONS

略  図
OUTLINE

000-802-080

M4
2

WASHER
CODE NO.

000-864-937

05DZ-X-9502
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

A-9

付属品表

CODE NO.

005-959-720

TYPE

FP05-05701

05EC-X-9502 -2
1/1

RB-8800

ACCESSORIES
名  称
NAME

番 号
NO.

4

SELF-TAPPING SCREW
CODE NO.

3

000-864-937

4X20 SUS304

+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ

ﾌﾞﾗｲﾝﾄﾞｼｰﾙ

用途／備考
REMARKS

4

WASHER
CODE NO.

2

数量
Q'TY

M4

ﾎﾟﾘｶﾜｯｼｬｰ
1

型名／規格
DESCRIPTIONS

略  図
OUTLINE

000-805-687

05-086-1102-2
4

SEAL
CODE NO.

100-281-282

05EC-X-9502
ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

A-10

NAME OF
PART

OUTLINE

ﾋｭｰｽﾞ

1

005-377-820

TYPE

SP05-05501

SPARE PARTS LIST FOR

SHIP NO.

ITEM
NO.

CODE NO.

U

DWG. NO.
OR
TYPE NO.

S

05EC-X-9301 -0 1/1
BOX NO.

P

SETS PER
VESSEL

E

QUANTITY

REMARKS/CODE NO.

WORKING
PER
SET

PER
VES

FGBO 15A
AC125V

SPARE

2

FUSE

000-549-014

MFR'S NAME

FURUNO

ELECTRIC

CO.,LTD.

DWG NO.

05EC-X-9301

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

1/1

DOCUMENT

000-149-932 **

000-809-270 **
IM*-56420-*

*52-00101-*

005-371-850

CP05-10201

000-054-223

005-951-790
HS-2003

FP05-05510

005-377-820

SP05-05501

000-054-240 **

1

1

Q'TY

1

1

1

1

1

FP05-05800

RC-8800S/D-N-75BG,RC8800S/D-A-75BG

DESCRIPTION/CODE №

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

DISTRESS PROCEDURE

遭難通信要領書

OPERATOR'S GUIDE

操作要領書

OPERATOR'S MANUAL

取扱説明書

NAME
OUTLINE

RC-8800S/D-N-75BG、RC-8800S/D-A-75BG

ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.

INSTALLATION MANUAL

装備要領書

VHF/MF DISTRESS ALERT FLOW

遭難警報ﾌﾛVHFMF*

図書

OUTLINE

INSTALLATION MATERIALS

ACCESSORIES

SPARE PARTS

UNIT

INSTALLATION MATERIALS

工事材料

工事材料

HANDSET

ﾊﾝﾄﾞｾｯﾄ

BRACKET FOR HANDSET

ﾊﾝﾄﾞｾｯﾄﾊﾝｶﾞｰ組品

付属品

SPARE PARTS

予備品

予備品

VHF CONSOLE

VHFｺﾝｿｰﾙ

ユニット

NAME

ＰＡＣＫＩＮＧ ＬＩＳＴ

05EC-X-9861

000-149-935

000-149-934 **
TIC-56420-*

000-149-930 **
OS*-56420-*

OM*-56420-*

DESCRIPTION/CODE №

05EC-X-9861 -0
1/1

1

1

1

Q'TY

A-11

1

番 号
NO.

CABLE ASSY.

ﾐﾆﾋﾟﾝ組品(1)

略  図
OUTLINE

CODE NO.

L-420

000-151-748

型名／規格
DESCRIPTIONS

CP05-10201

TYPE

1

数量
Q'TY

1/1

05EC-X-9409

Used only Japan

用途／備考
REMARKS

05EC-X-9409 -0

ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

名  称
NAME

INSTALLATION MATERIALS

工事材料表

005-371-850

CODE NO.

A-12

N A M E
O U T L I N E

INSTALLATION MATERIALS

UNIT

005-371-670

CP05-10001

005-371-650 **

RC-8800-N

DESCRIPTION/CODE №

05EC-X-9860 -0

（略図の寸法は、参考値です。

05EC-X-9860

DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表ｺｰ ﾄﾞを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.

INSTALLATION MATERIALS

工事材料

工事材料

CONSOLE KIT

ｺﾝｿｰﾙ組品

ユニット

RC-8800-N/RC-8800-A

ＰＡＣＫＩＮＧ ＬＩＳＴ

1

1

Q'TY

1/1

A-13





⇟ภ
01

%#$.'#55;

㩚㩐㩕㩩㩧⚵ຠ


%#$.'#55;

㩃㨺㩖㩨㩣⚵ຠ

⇛‫ޓޓ‬࿑
176.+0'

%1&'01

.

%1&'01





&57$/2*:.

ဳฬ㧛ⷙᩰ
&'5%4+26+105

%2

6;2'





ᢙ㊂
3	6;



'%:

↪ㅜ㧛஻⠨
4'/#4-5

'%: 

㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕

ฬ‫ޓޓ‬⒓
0#/'

+056#..#6+10/#6'4+#.5

Ꮏ੐᧚ᢱ⴫



%1&'01

A-14

0#/'

&1%7/'06



%)



8%6(:%/



,'

%2



22

&'5%4+26+10%1&'ͳ

'%: 

䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩

'%:

A-15









3	6;



㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅

ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯

176.+0'&4#9+0)
,2'0

ᄖኸ࿑㧔๺⧷㧕

࿑ᦠ

176.+0'

+056#..#6+10/#6'4+#.5

70+6

219'4%#$.'
(14&%/#+05

㔚Ḯ㩃㨺㩖㩨㩣㧰㧯↪

%#$.'#55;

㩃㨺㩖㩨㩣⚵ຠ

Ꮏ੐᧚ᢱ

24+06'470+6

㩖㩩㩢㩧㩊

࡙࠾࠶࠻

22

㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀

Y. Hatai

D-1

Y. Hatai

D-2

Y. Hatai

D-3

D-4

Y. Hatai

Y. Hatai

D-5

Y. Hatai

D-6

This page is intentionally left blank.

D-7

Y. Hatai

D-8

Y. Hatai

Mar.11'04

H.Hayashi

D-9

D-10

D-11

Feb.02'05

D-12

D-13

Nov.28'03

D-14

D-15

Y. Hatai

D-16

Y. Hatai

D-17

D-18

Dec.26'03

D-19

Dec.26'03

Y. Hatai

D-20

1

2

3

4
*2

*2

A

接続箱
JUNCTION BOX
IF-8810

送受信機
TRANSCEIVER UNIT
FM-8800D/S

T/R用アンテナ
ANTENNA FOR T/R

IEC61162-1(NMEA)/REMOTE

CH70 WR用アンテナ
ANTENNA FOR CH70 WR

+15VDC 1
+15VDC 2
+15VDC 3
+15VDC 4
N.C 5
N.C 6
TXD(H) 7
TXD(C) 8
RXD(H) 9
RXD(C) 10

*2

M-P-5

D-SUB 37P

ANT
1
2

1
2

EXT.ALM_N
0V
W-MIC1(H)
W-MIC1(C)
W-SP1(H)
W-SP1(C)
W-PTT1_N
0V
0V
0V
0V
0V

11
12
13
14
15
16
17
18
19
20
21
22

VDR AF(H)
VDR AF(C)
DATA_A
DATA_B
LINE OUT(H)
LINE OUT(C)
LINE IN(H)
LINE IN(C)
W-MIC2(H)
W-MIC2(C)
W-SP2(H)
W-SP2(C)
W-PTT2_N
0V
F.GND

23
24
25
26
27
28
29
30
31
32
33
34
35
36
37

B
HANDSET

ハンドセット

1
2
3
4
5
6
7
8

HANDSET
HS-2003

外部スピーカ
EXT. SP

S.GND
PTT SW_N
MIC(H)
MIC(C)
HS SP(H)
HOOK SW_N
+5V
F.GND

SPKR
1
2

2.8 m

SP(H)
SP(C)

SEM-21Q *2

C

*1
DPYC-1.5
100-115/
200-230 VAC

AC
IN

*1
DPYC-2.5
+ 24VDC
24 VDC
- IN

AC/DC電源
AC-DC POWER
SUPPLY
PR-240-CE
*2

DC +
OUT -

PE 保護アース
IV-2sq. *1
24VDC
24 VDC

RED
BLK

D

RED

05S9371,3m

注記 *1）造船所手配。 15A
*2）オプション。
*3）最大4台まで接続可能。
*4）ケーブルクランプで接地。
*5）終端のユニットでは内部で
ジャンパー(J2, J3)をONにする。
*6）P: 撚り対線
*7）ノーマルクローズ、フローティング
最大80mA、耐圧≦50V。
NOTE *1.
*2.
*3.
*4.
*5.

SHIPYARD SUPPLY
OPTION
Max. 4 sets
GROUND THROUGH CABLE CLAMP.
CONNECT JUMPERS (J2 & J3)
ON TERMINATED REMOTE STATION.
*6. P: TWISTED PAIR CABLE
*7. NORMAL CLOSE, FLOATING, MAX80mA,
WITHSTAND VOLTAGE ≦50V.

BLK

24VDC(+)
24VDC(-)

GND

PRINTER
STROBE_N
D0
D1
D2
D3
D4
D5
D6
D7
ACK_N
BUSY
PE
SELECT
ALF_N
ERROR_N
INIT._N
SLCT IN_N
F.GND
0V
F.GND
F.GND
F.GND
F.GND
F.GND
F.GND

P
P
P
P

P
P
P
P
P
P

P
P
P
P
P
P
P

*2
D-SUB 25P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND
EXT.ALM_N
*7
0V
F.GND
W-MIC1(H)
W-MIC1(C)
W-SP1(H)
W-SP1(C)
J2
W-PTT1_N
1
0V
2
F.GND
3
W-MIC2(H)
4
W-MIC2(C)
5
W-SP2(H)
6
W-SP2(C)
7
W-PTT2_N
8
0V
9
F.GND
10
VDR AF(H)
11
VDR AF(C)
12
NOT USED_1
NOT USED_2
J3
F.GND
1
+15VDC
2
0V
3
DATA_A
4
DATA_B
5
LINE IN(H)
6
LINE IN(C)
7
LINE OUT(H)
8
LINE OUT(C)
9
F.GND
10
N.C
11
+15VDC
12
0V
13
DATA_A
14
DATA_B
LINE IN(H)
LINE IN(C)
LINE OUT(H)
LINE OUT(C)
F.GND
N.C
N.C
1
2
3
4
5
6
7
8
9
10

P

CH70 RX ANT
M-P-5

J1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

航法装置,プロッタ
NAVIGATION
DEVICE, PLOTTER
RXD(H)
RXD(C)
TXD(H)
TXD(C)

*2
CO-SPEVV-SB-C
*4 0.2X2P,φ10.5
キ
YEL
P ダイ
ORG
アカ
RED
P チャ
BRN

*1
TTYCS-1 MAX. 20m

*4

*4

アカ
Pキ
クロ
Pキ
シロ
Pキ

RED
YEL
BLK
YEL
WHT
YEL

アカ
Pキ
クロ
Pキ
シロ
Pキ

RED
YEL
BLK
YEL
WHT
YEL

17JE-23250-02,3m

プリンタ*2
PRINTER

VDR
*4
*2
05S0309
P
P
P
P

終端まで最大50m
MAX. 50m TO LAST UNIT

シロ(太)
クロ(太)
ミドリ
アオ
キ
ダイ
アカ
チャ

PP-510

*2

*2

Wing Mic

マイクレセプタクルボックス
MIC RECEPTACLE BOX
RBD-VHF(B)

ハンドセット
HANDSET

TB1

1
2
3
4
5
6
7

HS-6000FZ-11
HS-6000FZ-5

外部アラーム
Ext. Alarm *1

1
2
3
4

キ
シロ
アカ
キ
クロ
キ

YEL
WHT
RED
YEL
BLK
YEL

1
2
3
4
5
6
7
8

*4
シロ(太)
P クロ(太)
ミドリ
P アオ
キ
P ダイ
アカ
P チャ

WHT(BIG)
BLK(BIG)
GRN
BLU
YEL
ORG
RED
BRN

+15VDC
1
OV
2
DATA_A
3
DATA_B
4
LINE IN(H) 5
LINE IN(C) 6
LINE OUT(H) 7
LINE OUT(C) 8
TB3

WHT(BIG)
BLK(BIG)
GRN
BLU
RED
BRN
YEL
ORG

TB1

P
P

*4

アカ RED
クロ BLK
シロ WHT

TB1

*4

11
12
13
14
17
18
15
16
F.GND 19
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND

IV-1.25sq.
*1

20
21
22
23
24

1
2
3
4
5
6
7
8

P
P

4

YEL
WHT
RED
YEL
BLK
YEL

P
P
P

ハンドセット
*2
HANDSET
HS-8800
リモートステーション 4
REMOTE STATION *2
RB-8800/RB-8810
DATA_A 1
*3
DATA_B 2
*5
CONT 3
DIST_SW 4
LINE OUT(H) 5
LINE I/O(C) 6
LINE IN(H) 7
+15V1 8
OV 9
F.GND 10
TB1
TB2

左と同じ
Same as
left

TB3

TB3

TB3
IV-1.25sq. *1

リモートステーション
REMOTE STATION *2
RB-8800/RB-8810
*3
*5

1
2
3
4
5
6
7
8
9 F.GND
10 N.C

24VDC

リモートステーション 3
REMOTE STATION *2
RB-8800/RB-8810
DATA_A 1
*3
DATA_B 2
CONT 3
DIST_SW 4
LINE OUT(H) 5
LINE I/O(C) 6
LINE IN(H) 7
+15V1
8
OV 9
F.GND 10
TB1
TB2

IV-1.25sq. *1

DMC I/F *2
IF-8820

キ
シロ
アカ
キ
クロ
キ

1
2
3

ハンドセット
*2
HANDSET
HS-8800

左と同じ
Same as
left

IV-1.25 *1

MAX. 50m TO LAST UNIT

1
2
3
4
5
6
7

CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX.20m *2

1
2
3
4
5
6
7
8

*2
05S0309
終端まで最大50m

マイクレセプタクルボックス
MIC RECEPTACLE BOX
RBD-VHF(B)

HS-6000FZ-11
HS-6000FZ-5

P

リモートステーション 2
REMOTE STATION *2
RB-8800/RB-8810
DATA_A 1
*3
DATA_B 2
CONT 3
DIST_SW 4
LINE OUT(H) 5
LINE I/O(C) 6
LINE IN(H) 7
+15V1 8
OV 9
F.GND 10
TB2
TB1

シロ(太)
Pクロ(太)
ミドリ
Pアオ
アカ
Pチャ
キ
Pダイ

*2

ハンドセット
HANDSET

ハンドセット
*2
HANDSET
HS-8800

リモートステーション 1
REMOTE STATION *2
RB-8800/RB-8810
DATA_A 1
*3
DATA_B 2
CONT 3
DIST_SW 4
LINE OUT(H) 5
LINE I/O(C) 6
LINE IN(H) 7
+15V1 8
OV 9
F.GND 10
TB2
TB1

WHT(BIG)
BLK(BIG)
GRN
BLU
YEL
ORG
RED
BRN

VCTF0.75x3C,5m,φ7
+ 1
- 2
GND 3

*2

Wing Mic

ハンドセット
*2
HANDSET
HS-8800

TTYCS-1 MAX. 20m *1

S-1

6

CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX. 20m *2

IV-1.25sq.
*1

IV-1.25sq. *1

ハンドセット *2
HANDSET 上に同じ
Same as
HS-8800 above

TB2
+15VDC
OV
DATA_A
DATA_B
上に同じ
LINE IN(H)
Same as
LINE IN(C)
above
LINE OUT(H)
LINE OUT(C)
TB3
IV-1.25sq.*1

ダイ
ORG
キ
YEL
チャ
BRN
アカ
RED
*1 CO-SPEVV-SB-C
0.2x2P(5/10/15/20/30m)

遭難警報装置
*2
DISTRESS MESSAGE CONTROLLER
DMC-5

1
2
3
4
6

TB1/TB2
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND

IV-1.25sq.
*1

プリンタ*2
PRINTER

VCTF0.75x2C,3m
+ 1
- 2

シロ WHT
クロ BLK

PP-8800
*1
IV-2sq.

5

IV-1.25sq.
*1

24VDC

DRAWN
Jun. 9,'06
CHECKED
APPROVED
SCALE
DWG No.

E.MIYOSHI
TAKAHASHI.T

TITLE

FM-8800D/S

名称

国際VHF無線電話装置
相互結線図

NAME

VHF RADIOTELEPHONE
INTERCONNECTION DIAGRAM

Y. Hatai
MASS

C5642-C01- J

kg

FURUNO ELECTRIC CO., LTD.

3

M-P-5

M-P-5

ハンドセット
HANDSET
HS-2003

B

外部スピーカ
EXT. SPEAKER
SEM-21Q *2

1
2

1
2

1
2
3
4
5
6
7
8

φ3.5

2.8m

ANT
J1

IEC61162-1(NMEA)/REMOTE

CH70 RX ANT
J2

HANDSET
S.GND
PTT SW-N
MIC-H
MIC-C
HS SP-H
HOOK SW-N
+5V
F.GND
SPKR
SP-H
SP-C

GND

C

XM2A-3701

+15VDC 1
+15VDC 2
+15VDC 3
+15VDC 4
NC 5
NC 6
TXD-H 7
TXD-C 8
RXD-H 9
RXD-C 10

*1

非常灯
*2
EMERGENCY LAMP

TB1
1
2
3
4
5
6
7
8

11
12
13
14
15
16
17
18
19
20
21
22

VDR AF-H
VDR AF-C
DATA-A
DATA-B
LINE OUT-H
LINE OUT-C
LINE IN-H
LINE IN-C
W_MIC2-H
W_MIC2-C
W_SP2-H
W_SP2-C
W_PTT2-N
0V
F.GND

23
24
25
26
27
28
29
30
31
32
33
34
35
36
37

1

15A
RED
BLK

2
3
4
5
6
7
8
9
10
11
12
13
14
15

P
P
P
P
P

W_MIC2-H
W_MIC2-C
W_SP2-H
W_SP2-C
W_PTT2-N
0V
F.GND

16
17
18
19
20
21
22

VDR AF-H
VDR AF-C
J3
NOT USED_1
1
NOT USED_2
2
F.GND
3
4
+15VDC
5
0V
6
DATA-A
7
DATA-B
8
LINE IN-H
9
LINE IN-C
10
LINE OUT-H
11
LINE OUT-C
12
F.GND
13
NC
14

23
24
25
26
27

J2
EXT.ALM-N
0V
W_MIC1-H
W_MIC1-C
W_SP1-H
W_SP1-C
W_PTT1-N
0V
0V
0V
0V
0V

PRINTER

24VDC DPYC-2.5

TXD-C
RXD-H
RXD-C
F.GND
EXT.ALM-N
*7
0V
F.GND
W_MIC1-H
W_MIC1-C
W_SP1-H
W_SP1-C
W_PTT1-N
0V
F.GND

J1
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
11
12

P
P
P
P
P
P

P
P
P
P
P
P
P

D-SUB 25P

24VDC(+)
24VDC(-)
25

S1
1
2
3

1 ～ 36

J3
0V
24V

J2

+15VDC
0V
DATA-A
DATA-B
LINE IN-H
LINE IN-C
LINE OUT-H
LINE OUT-C
F.GND
NC
NC

28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

TTYCS-4(*1) OR
CO-SPEVV-SB-C
0.2x2P,φ10.5(*2)

航法装置/プロッタ
NAVIGATOR
PLOTTER

P
P
*1
TTYCS-1,MAX.20m
*2
CO-SPEVV-SB-C 0.2x5P,
*4 φ13.5,MAX.20m
アカ RED
P
キ YEL
クロ BLK
P
キ YEL
シロ WHT
P
キ YEL *2
*4 CO-SPEVV-SB-C 0.2x5P,
φ13.5,MAX.20m
アカ RED
キ YEL
クロ BLK
キ YEL
シロ WHT
キ YEL
*4
*1
TTYCS-1,MAX.20m
*4

外部アラーム *1
EXTERNAL ALARM
TB1 マイクレセプタクル
1 ボックス
2 MIC RECEPTACLE
3 BOX
4 RBD-VHF(B) *2

TB1 マイクレセプタクル
1 ボックス
2 MIC RECEPTACLE
3 BOX
4 RBD-VHF(B) *2

VDR

*4
*2
05S0309

終端まで最長50m
TOTAL 50m OR LESS TO TERMINATE

シロ(太)
クロ(太)
ミドリ
アオ
アカ
チャ
キ
ダイ

P
P
P
P

WHT[B]
BLK[B]
GRN
BLU
RED
BRN
YEL
ORG

1
2
3
4
5
6
7
8

*4
*2
05S0309

TOTAL 50m OR LESS TO TERMINATE

シロ(太)
クロ(太)
ミドリ
アオ
アカ
チャ
キ
ダイ

P
P
P

WHT[B]
BLK[B]
GRN
BLU
RED
BRN
YEL
ORG

*4

1 ～ 34

1 ～ 34

1
2
3
4
5
7

HS-6000FZ-11
HS-6000FZ-5

Wing Mic
ハンドセット
HANDSET *2

1
2
3
4
5
7

HS-6000FZ-11
HS-6000FZ-5

TB2

リモートステーション
REMOTE STATION
RB-8800/RB-8810

*3
LINE IN-H
LINE IN-C
LINE OUT-H
LINE OUT-C

1
2
3
4
5
6
7
8

*1
IV-1.25sq.

終端まで最長50m

P

Wing Mic
ハンドセット
HANDSET *2

TB1

1
DMC I/F
2
IF-8820 *2
3
4
5
6
7
8
9 F.GND
F.GND
10 NC

11
12
13
14
15
16
17
18
19

TXD-H
TXD-C
RXD-H
RXD-C
F.GND

20
21
22
23
24

I/F
05P0541
J1

S-2

6

*6

ハンドセット
HANDSET *2

1
2
3
4
5
6
7
8
9
10

A

CH70 WR用アンテナ *2
ANTENNA FOR CH70 WR

接続箱
JUNCTION BOX
IF-8810
TXD-H 1

送受信機
TRANSCEIVER UNIT
FM-8800D/S

5

HS-8800

*2
05S0309
シロ(太)
クロ(太)
ミドリ
アオ
アカ
チャ
キ
ダイ
*2
05S0309
シロ(太)
クロ(太)
ミドリ
アオ
アカ
チャ
キ
ダイ

ハンドセット
HANDSET *2
HS-8800

DATA-A
DATA-B
CONT
DIST_SW
LINE OUT-H
LINE I/O-C
LINE IN-H
+15V1
OV
F.GND

T/R用アンテナ *2
ANTENNA FOR T/R

4

1
2
3
4
5
6
7
8
9
10

2

DATA-A
DATA-B
CONT
DIST_SW
LINE OUT-H
LINE I/O-C
LINE IN-H
+15V1
OV
F.GND

1

TB1

WHT[B]
BLK[B]
GRN
BLU
RED
BRN
YEL
ORG

1
2
3
4
5
6
7
8

TB2
1
リモートステーション 2
REMOTE STATION
RB-8800/RB-8810 3
4

*3
5
6
7
8

*5
リモートステーション
REMOTE STATION
RB-8800/RB-8810


*1
IV-1.25sq.
1 TB1
2 リモートステーション
3 REMOTE STATION
RB-8800/RB-8810
4
*3
5
6
7
8

WHT[B]
BLK[B]
GRN
BLU
RED
BRN
YEL
ORG

ハンドセット
HANDSET *2
HS-8800

*5
リモートステーション
REMOTE STATION
RB-8800/RB-8810

*1
IV-1.25sq.
*2
CO-0.2x2P,5/10/15/20/30m
P
P

*1
IV-1.25sq.

1
2
3
4
5

TB1/TB2
TXD-H
TXD-C
RXD-H
RXD-C
F.GND

遭難警報装置
DISTRESS MESSAGE
CONTROLLER
DMC-5
*1
IV-1.25sq.

J2

プリンタ
PRINTER
UTP-80FK

D

*6

RACK CONSOLE
注記
*1）造船所手配。
*2）オプション。
*3）最大4台まで接続可能。
*4）ケーブルクランプで接地。
*5）終端ユニットは内部のジャンパー（J2,J3）をONにする。
*6）プリンタ有の場合
*7）ノーマルクローズ、フローティング、最大80mA、耐圧≦50V。

NOTE
*1.
*2.
*3.
*4.
*5.
*6.
*7.

SHIPYARD SUPPLY
OPTION
MAX. 4 SETS AVAILABLE
GROUND THROUGH CABLE CLAMP.
CONNECT JUMPERS (J2 & J3) ON TERMINATED REMOTE STATION.
IN CASE OF "W/PRINTER"
NORMAL CLOSE, FLOATING, MAX80mA, WITHSTAND VOLTAGE ≦50V.

DRAWN
Jun.9,'06
CHECKED
APPROVED
SCALE
DWG No.

E.MIYOSHI
TAKAHASHI.T

TITLE

RC-8800 (FM-8800)

名称

国際VHF無線電話装置（ラック組込）
相互結線図

NAME

VHF RADIOTELEPHONE (RACK CONSOLE)
INTERCONNECTION DIAGRAM

Y. Hatai
MASS

C5642-C02- D

kg

FURUNO ELECTRIC CO., LTD.

1

2

T/R用アンテナ
ANTENNA FOR T/R
CH70 WR用アンテナ
ANTENNA FOR CH70 WR

M-P-5

1
2
CH70 RX ANT

M-P-5

1
2

B

HANDSET

ハンドセット

1
2
3
4
5
6
7
8

HANDSET
HS-2003

S.GND
PTT SW_N
MIC(H)
MIC(C)
HS SP(H)
HOOK SW_N
+5V
F.GND

SPKR
1
2

2.8 m

SP(H)
SP(C)

SEM-21Q *2

C

100-115/200-230 VAC

24 VDC

*1
DPYC-1.5

*1
DPYC-2.5

+ 24 VDC
- IN

*2

DC +
OUT -

PE 保護アース
IV-2sq. *1
24 VDC
24 VDC

05S9371,3m

RED
15A

D

BLK

RED
BLK

24 VDC(+)
24 VDC(-)

注記
*1）造船所手配。
*2）オプション。
*3）ケーブルクランプで接地。
*4）コネクタクランプで接地。
*5）ノーマルクローズ、フローティング
最大80mA、耐圧≦50V。

NOTE
*1.
*2.
*3.
*4.
*5.

SHIPYARD SUPPLY
OPTION
GROUND THROUGH CABLE CLAMP.
GROUND THROUGH CONNECTOR CLAMP.
NORMAL CLOSE, FLOATING, MAX80mA,
WITHSTAND VOLTAGE ≦50V.

EXT.ALM_N
*5
0V
F.GND

11
12
37

W-MIC1(H)
W-MIC1(C)
W-SP1(H)
W-SP1(C)
W-PTT1_N
0V
F.GND

13
14
15
16
17
18
37

GND

P
P

+15VDC
0V
DATA_A
DATA_B
LINE IN(H)
LINE IN(C)
LINE OUT(H)
LINE OUT(C)
F.GND

1
19
25
26
27
28
29
30
37

W-MIC2(H)
W-MIC2(C)
W-SP2(H)
W-SP2(C)
W-PTT2_N
0V
F.GND

31
32
33
34
35
36
37

STROBE_N
D0
D1
D2
D3
D4
D5
D6
D7
ACK_N
BUSY
PE
SELECT
ALF_N
ERROR_N
INIT._N
SLCT IN_N
F.GND
0V
F.GND
F.GND
F.GND
F.GND
F.GND
F.GND

*2
CO-SPEVV-SB-C 0.2X2P,φ10.5
キ
YEL
ダイ
ORG
アカ
RED
チャ
BRN

*4
P
P
P

アカ
キ
クロ
キ
シロ
キ

*4

*4
P
P
P
P
*4
P
P
P

P: 撚り対線
P: TWISTED PAIR CABLE

P

TB1

YEL
WHT
RED
YEL
BLK
YEL

1
2
3
4
5
6
7

1
2
3
4

HS-6000FZ-11
HS-6000FZ-5

VDR

WHT(BIG)
BLK(BIG)
GRN
BLU
YEL
ORG
RED
BRN

*2
05S0309
終端まで最大50m

DMC I/F *2
IF-8820

MAX. 50m TO LAST UNIT

RED
YEL
BLK
YEL
WHT
YEL

1
2
3
4
5
6
7
8
9 F.GND
10 N.C

*3

11
12
13
14
17
18
15
16
F.GND 19
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND

*4

*2
D-SUB 25P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

P

キ
シロ
アカ
キ
クロ
キ

ハンドセット
HANDSET
*2

CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX. 20m *2

TTYCS-1 MAX. 20m *1

アカ
キ
クロ
キ
シロ
キ

P

外部アラーム
Ext. Alarm
*1

RED
YEL
BLK
YEL
WHT
YEL

シロ(太)
クロ(太)
ミドリ
アオ
キ
ダイ
アカ
チャ

Wing Mic

マイクレセプタクルボックス
*2
MIC RECEPTACLE BOX
RBD-VHF(B)

*1
TTYCS-1 MAX. 20m

20
21
22
23
24

遭難警報装置
DISTRESS MESSAGE CONTROLLER
DMC-5

P
P

ダイ
ORG
キ
YEL
チャ
BRN
アカ
RED
CO-SPEVV-SB-C
0.2x2P(5/10/15/20/30m),φ10.5

1
2
3
4
6

TB1/TB2
TXD(H)
TXD(C)
RXD(H)
RXD(C)
F.GND

*2

IV-1.25sq.
*1

CO-SPEVV-SB-C 0.2x5P,φ13.5 MAX. 20m *2

17JE-23250-02,3m

プリンタ*2
PRINTER
PP-510

VCTF0.75x3C,5m,φ7
+ 1
- 2
GND 3

アカ RED
クロ BLK
シロ WHT

24VDC

P
P
P
VCTF0.75x2C,3m

プリンタ*2
PRINTER

+ 1
- 2

シロ WHT
クロ BLK

IV-1.25sq.
*1

E. MIYOSHI
TAKAHASHI.T

APPROVED

Y. Hatai

SCALE

MASS

DWG No.

キ
シロ
アカ
キ
クロ
キ

YEL
WHT
RED
YEL
BLK
YEL

C5642-C03- D

kg

ハンドセット
*2
HANDSET

TB1

1
2
3
4

24VDC

DRAWN
Jun. 9,'06
CHECKED

Wing Mic

マイクレセプタクルボックス
*2
MIC RECEPTACLE BOX
RBD-VHF(B)

IV-1.25sq.
*1

PP-8800
*1
IV-2sq.

S-3

6

航法装置,プロッタ
NAVIGATION
DEVICE, PLOTTER
RXD(H)
RXD(C)
TXD(H)
TXD(C)

*4

VDR AF(H) 23
VDR AF(C) 24
F.GND 37

PRINTER

AC/DC電源
AC-DC POWER
SUPPLY
PR-240-CE

AC
IN

D-SUB 37P

TXD(H) 7
TXD(C) 8
RXD(H) 9
RXD(C) 10
F.GND 37

ANT

5

*2

IEC61162-1(NMEA)/REMOTE

*2

外部スピーカ
EXT. SP

4

送受信機
TRANSCEIVER UNIT
FM-8800D/S

*2

A

3

1
2
3
4
5
6
7

HS-6000FZ-11
HS-6000FZ-5

TITLE

FM-8800D/S

名称

国際VHF無線電話装置
相互結線図（接続箱無し）

NAME

VHF RADIOTELEPHONE
INTERCONNECTION DIAGRAM(W/O J.B.)

FURUNO ELECTRIC CO., LTD.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 69
Page Mode                       : UseOutlines
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:ca4175aa-caef-4110-b742-23ac21f5302e
Producer                        : Acrobat Distiller 4.05 for Windows
Create Date                     : 2004:03:11 15:10:34Z
Modify Date                     : 2006:06:15 16:09:04+09:00
Metadata Date                   : 2006:06:15 16:09:04+09:00
Document ID                     : uuid:88c534af-493a-4181-8015-13f19761a199
Instance ID                     : uuid:daada42b-1e1a-4502-afe0-47cfae7d3154
Format                          : application/pdf

EXIF Metadata provided by EXIF.tools