Furuno Nx 300 Users Manual
NX-300 to the manual 34570d94-9832-4d53-92ab-928d85d39d57
2015-02-02
: Furuno Furuno-Nx-300-Users-Manual-428781 furuno-nx-300-users-manual-428781 furuno pdf
Open the PDF directly: View PDF .
Page Count: 60
Download | ![]() |
Open PDF In Browser | View PDF |
NAVTEX RECEIVER NX-300 Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya, Japan Telephone : 0798-65-2111 Telefax : 0798-65-4200 All rights reserved. Printed in Japan FIRST EDITION : MAR. 2000 H PUB.No. OME-56290 ( YOSH ) NX-300 : MAY. 14,2002 *00080900001* *00080900001* *00080900001* *OME56290H00* *OME56290H00* *OME56290H00* SAFETY INSTRUCTIONS Safety Instructions for the Operator WARNING Do not open the cover of the equipment. Only qualified personnel should work inside the equipment. CAUTION Keep heater away from equipment. A heater can melt the equipment's power cord, which can cause fire or electrical shock. Use the proper fuse. Immediately turn off the power at the ship's mains switchboard if water or foreign object falls into the equipment or the equipment is emitting smoke or fire. Continued use of the equipment can cause fire, electrical shock and serious injury. Use of the wrong fuse can cause fire or equipment damage. Do not operate the equipment with wet hands. Electrical shock can result. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. i Safety Instructions for the Installer CAUTION WARNING Do not open the cover unless totally familiar with electrical circuits and service manual. Improper handling can result in electrical shock. Turn off the power at the ship's mains switchboard before beginning the installation. Post a warning sign near the switchboard to ensure that the power will not be applied while the equipment is being installed. Serious injury or death can result if the power is not turned off, or is applied while the equipment is being installed. Ground the equipment to prevent mutual interference. Confirm that power supply voltage is compatible with the voltage rating of the equipment. Connection to the wrong power supply can cause fire or equipment damage. The voltage rating appears on the label at the rear of the equipment. Observe the following compass safe distances to prevent interference to a magnetic compass: NX-300 ii Standard compass Steering compass 0.5 m 0.3 m CONTENTS FOREWORD................................................................................................................... v A Word to NX-300 Owners ................................................................................................................v Features .......................................................................................................................................... vi SYSTEM CONFIGURATION ........................................................................................ vii EQUIPMENT LISTS .................................................................................................... viii 1. PRINCIPLE OF NAVTEX SYSTEM........................................................................ 1-1 1.1 How NAVTEX Works...............................................................................................................1-1 1.2 NAVTEX System Operation.....................................................................................................1-1 1.3 Message Format.....................................................................................................................1-2 1.4 Display Indications ..................................................................................................................1-3 1.5 NAVTEX Station Map ..............................................................................................................1-4 1.6 NAVTEX Station List ...............................................................................................................1-5 2. OPERATION........................................................................................................... 2-1 2.1 Control Description .................................................................................................................2-1 2.2 Turning the Power On/Off........................................................................................................2-1 2.3 Adjusting Dimmer and Contrast...............................................................................................2-2 2.4 Menu Operation Overview.......................................................................................................2-2 2.5 Selecting Stations ...................................................................................................................2-3 2.6 Selecting Messages................................................................................................................2-4 2.7 Setting Functions (FUNCTIONS menu)...................................................................................2-5 2.8 Selecting Language ................................................................................................................2-9 2.9 Displaying Messages ..............................................................................................................2-9 2.10Sample Messages ................................................................................................................2-10 2.11 Displaying Navigation Data ................................................................................................... 2-11 2.12 Selecting Receive Frequency...............................................................................................2-12 3. SYSTEM MENU...................................................................................................... 3-1 3.1 Units of Measurement .............................................................................................................3-1 3.2 Time Difference (using local time) ...........................................................................................3-2 3.3 Time Display ...........................................................................................................................3-3 3.4 Default Setting ........................................................................................................................3-3 iii 3.5 Delete All Messages ....................................................................................................................3-4 3.6 User Display of Navigation Data..................................................................................................3-4 4. OTHER FUNCTIONS ............................................................................................. 4-1 4.1 DEMO Mode ................................................................................................................................4-1 4.2 VIEW Mode..................................................................................................................................4-1 4.3 All Clear .......................................................................................................................................4-1 4.4 Changing Received Message Log Window ..................................................................................4-2 5. MAINTENANCE & TROUBLESHOOTING............................................................. 5-1 5.1 Maintenance ................................................................................................................................5-1 5.2 Diagnostic Test ............................................................................................................................5-1 5.3 When the Battery Icon Appears...................................................................................................5-2 5.4 Replacement of Fuse...................................................................................................................5-3 6. INSTALLATION ...................................................................................................... 6-1 6.1 Installation of Display Unit ...........................................................................................................6-1 6.2 Installation of Antenna Unit..........................................................................................................6-2 6.3 Wiring...........................................................................................................................................6-3 6.4 Interfacing ....................................................................................................................................6-4 MENU TREE ............................................................................................................. AP-1 SPECIFICATIONS .....................................................................................................SP-1 PACKING LIST ............................................................................................................A-1 OUTLINE DRAWING...................................................................................................D-1 INTERCONNECTION DIAGRAM ................................................................................ S-1 INDEX................................................................................................................... index-1 Declaration of Conformity iv FOREWORD A Word to NX-300 Owners Congratulations on your choice of the FURUNO NX-300 NAVTEX Receiver. We are confident that you will enjoy many years of operation with this fine piece of equipment. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. Our extensive global network of agents and dealers furthers this dedication to excellence. The NX-300 is just one of the many FURUNO developments in the field of marine radio communication. The NX-300 provides cost-effective price, high sensitivity and simple operation in one compact and light-weight unit. In addition to its fundamental function of receiving NAVTEX broadcasts, this unit can also function as nav data display when connected to navigation equipment. This unit is designed and constructed to ensure the user many years of trouble-free operation. To obtain full performance from the equipment, however, you should carefully read and follow the recommended procedures for installation, operation and maintenance. No machine can perform its intended functions unless it is installed and maintained properly. Thank you for considering and purchasing FURUNO equipment. v Features NAVTEX (Navigational Telex) is a worldwide coastal telex broadcasting system. Coastal NAVTEX broadcasting stations with specific ID's transmit Navigational warnings, Meteorological warnings, Search and Rescue (SAR) information and other navigational information for NAVTEX receiver-equipped vessels sailing in coastal waters. The FURUNO NX-300 NAVTEX receiver receives NAVTEX messages and automatically displays them together with station ID and message category information. The service range of a NAVTEX station is typically 200-400 nautical miles. A NAVTEX station normally broadcasts every 4 hours. The NAVTEX message is relevant for all types and sizes of vessels. The NX-300 is shipped from the factory equipped to receive 7 specific types of NAVTEX messages from all NAVTEX stations. However unnecessary stations can be rejected or necessary stations can be added by the "manual station selection" facility. If ship's position data is fed from navigation equipment, the NX-300 automatically decides in which NAVAREA the vessel is navigating, and selects stations. (NAVAREAs are geographical zones defined by the International Maritime Organization.) • Unattended operation once required data is entered. • Received data is not saved nor displayed when the error rate exceeds the percentage you set (max 39%). • No paper required • Designed for small boats and fishing vessels • Compact, stylish display and antenna units • Memory of up to 28,000 characters for last 72 hours • Navigation data can be fed through external input (connection with navigation aid required). • Bright 95 x 60 mm LCD with adjustable contrast and brilliance • Memory backup with a long-life lithium battery • Low power consumption vi SYSTEM CONFIGURATION H-field ANTENNA UNIT NX-3H-D Antenna Cable (10 m) NAVTEX RECEIVER NX-300-D FURUNO MENU ENT DISP DIM FREQ GPS navigator Personal Computer PWR Power Cable (2 m) 12-24 VDC NX-300 System configuration vii EQUIPMENT LISTS Standard supply Name NAVTEX Reveiver Antenna Unit Installation Materials Spare Parts Accessories Type Qty Remarks Including hanger and knob bolts NX-300-D 1 H-field type with 10 m cable NX-3H-D Power/Data cable (Type: MJ-A7SPF0005-020, Code No.: 000-139-384) 1 set Tapping screw (4 pcs., for fixing NAVTEX receiver, Type: 5x20, Code No.: 000-802-081) Fuse (2 pcs., Type: FGMB 1A, Code No.: 0001 set 114-805) Hard cover (Type: 20-016-1091, Code No.: 1001 set 297-032) Optional equipment Name Right Angle Antenna Base L-type Antenna Base Type No. 13-QA330 Code No. Remarks 000-803-239 For antenna unit No. 13-QA310 000-803-240 Handrail Antenna Base No. 13-RC5160 000-806-114 Mast Mount Kit Flush Mount Kit S Flush Mount Kit F CP20-01111 OP-20-17 OP-20-29 004-365-780 000-040-720 For flush mounting the 000-041-405 NAVTEX receiver viii 1. PRINCIPLE OF NAVTEX SYSTEM 1.1 How NAVTEX Works There are many types of navigational and meteorological information available on radio, such as NAVAREA, HYDROPAC, etc. However, these systems rely heavily upon the operator's experience and skill in tuning the radio and interpreting messages. In addition, constant monitoring to pick up wanted information among a vast volume of messages is not practical with a limited radio staff. To provide all mariners with up-to-the-minute information automatically, the NAVTEX system was developed. NAVTEX is an acronym meaning Navigational Telex, and as its name shows, it is a kind of narrow band radio teletype system for sending (by frequency shift keying) text messages expressed in a 7-unit code. The difference is that a NAVTEX transmitter transmits nine control characters (header code) ahead of the main message, so that the receiver can identify the station, message type and serial number automatically. 1.2 NAVTEX System Operation For navigation purposes, the world is divided into 16 areas (called Navareas) as shown in the figure below. Each Navarea has multiple NAVTEX stations and each NAVTEX station has an identification code, from "A" to "Z." The frequency assigned to NAVTEX is only one (518 kHz), and many stations exist in the same Navarea. (Some stations use 490 kHz also.) Figure 1-1 NAVTEX area If the stations were to transmit without any rule, the system would collapse due to mutual interference. To avoid this problem, the following rules apply. • The transmission schedule is determined so that two or more stations having a common service area may not overlap in time. • Each station transmits with minimum required power to cover its service area (200 nautical miles nominal). 1-1 1.3 Message Format For automatic identification of messages, each message starts with eight control characters, called "Header codes". The first four characters are always "ZCZC" and common to all messages. This part is used for message synchronization. The latter four characters are designated as b1, b2, b3 and b4 to indicate origin, category and serial number of the message. Character b1 is the identification letter of the NAVTEX station; "A" to "Z". Character b2 indicates the type of message, "A" to "Z", as listed below. Character b3 and b4 indicate the serial number of the message. The serial numbers are counted up from "01" to "99", and start from "01" again. Number "00" is specially reserved for important emergency messages, such as a search and rescue (SAR) message. The end of each message is indicated by "NNNN" (four successive N's). General message format is summarized below. Header code ZCZC b1 b2 b3 b4 main message Start code (sync) Main message NNNN Termination code Serial number "00": Emergency message "01" - "99": Normal message Type of message "A" - "Z" (See the list below.) Station ID "A" - "Z" [Type of message (category)] A: Navigational warning I: OMEGA message B: Meteorological warning J: Differential OMEGA message C: Ice report K: D: Search and rescue information/ piracy and armed robbery Other electronic navigational aid system message L: Navigational warning (additional) E: Meteorological forecast M to U: Reserve-presently not used F: Pilot message V: G: DECCA message W to Y Reserve-presently not used H: LORAN-C message Z: 1-2 Notice to Fishermen (U. S. only) QRU (no message on hand) 1.4 Display Indications SAR: Displayed when message type D is displayed. NEW: Displayed when message is displayed for the first time. AUTO: Displayed when you select AUTO mode in STATION SELECTION. Rx: Lights when message is being received. SAR receiving: Lights (and the alarm sounds) when message type D is being received. Hitting any key silences the alarm. WARNING: Appears when message type A, B or L is displayed. WARNING receiving: Lights (and the alarm sounds) when message type A, B or L is received. Hitting any key silences the alarm. BATTERY icon: Displayed when the battery voltage is low. Scroll bar: Shows location in message displayed. Figure 1-2 Display indications 1-3 1.5 1-4 NAVTEX Station Map 1.6 NAVTEX Station List NAV area I Country Belgium Estonia Iceland Ireland Netherlands Norway Sweden United Kingdom Russian Federation II Cameroon Cape Verde France Mauritania Morocco Portugal Spain III Bulgaria Croatia Cyprus Egypt France Greece Israel Italy Malta Russian Federation Spain Turkey Ukraine Station Oostende Tallinn Reykjavik Radio Valencia Malin Head Netherlands Coast Guard Bodo Radio Rogaland Radio Vardoe Radio Svalbard Harnosand Karlskrona Stockholm Radio Cullercoats Portpatrick Niton Murmansk Archangel Douala Sao Vicente Radio Cross Corsen Nouadhibou Radio Casablanca Radio Horta Radio Monsanto Radio Corunna Tarifa Las Palmas Varna Split Cyprus Serapeum Alexandria Cross La Garde Heraklion Corfu Lemnos Haifa Roma Augusta Cagliari Trieste Malta Novorossiysk Astrakhan Cabo de la Nao Istanbul Samsun Antalya Izmir Mariupol Odessa Latitude 51 11N 59 30N 64 05N 51 56N 55 22N 52 06N 67 16N 58 39N 70 22N 78 02N 64 28N 55 29N 59 16N 55 02N 54 51N 50 35N 68 58N 64 33N N.I. N.I. 48 28N N.I. 33 36N 38 32N 38 44N 42 54N 36 01N 28 10N 43 04N 43 30N 35 03N 30 28N 31 12N 43 06N 35 20N 39 37N 39 52N 32 49N 41 37N 37 14N 39 13N 45 40N 35 49N 44 42N 46 18N 38 43N 41 04N 41 17N 36 53N 38 22N 47 06N 46 29N Longitude 02 48E 24 30E 21 51W 10 21W 07 21W 04 15E 14 23E 05 36E 31 06E 13 40E 21 36E 14 19E 18 43E 01 26W 05 07W 01 18W 33 05E 40 32E 05 03E 07 38W 28 38W 09 11W 09 16W 05 34W 15 25W 27 46E 16 29E 33 17E 32 22E 29 52E 05 59E 25 07E 19 55E 25 04E 35 00E 12 29E 15 14E 09 14E 13 46E 14 32E 37 44E 47 58E 00 09E 28 57E 36 20E 30 42E 26 36E 37 33E 30 44E 518kHz B1 M,T E,U R,X W Q P B L V A H J U,D G O K,SA C F N.I. N.I. A N.I. M F R D G I J Q M X N W H K L P R S,V T U O A W X D E F I B C 490kHz B1 I,U C A,I E J G S 1-5 NAV area IV V VI VII VIII IX Country Bermuda(UK) Canada Bermuda Sept Iles Prescott St. Johns Thunder Bay Sydney, Nova Scotia Yarmouth Montreal Labrador Denmark(Greenland-West Coast) Godthaab(Nuuk) United States Miami Boston New Orleans Chesapeake San Juan Netherlands Antilles Curacao Uruguay Colonia Laguna del Sauce La Paloma Montevideo Punta del Este Salto Argentina Ushaia Rio Gallegos Comodoro Rivadavia Bahia Blanca Mar del Plata Buenos Aires Namibia Walvis Bay South Africa Cape Town Port Elizabeth Durban India Bombay Madras Mauritius Mauritius Radio Bahrain Hamala Egypt Iran Saudi Arabia Oman Pakistan X 1-6 Station Serapeum (Ismailia) Bushehr Bandar Abbas Dammam Jeddah Muscat Karachi Latitude 32 23N 50 12N 44 56N 47 37N 48 34N 46 11N 43 44N 45 41N 53 42N 64 04N 25 37N 41 39N 29 53N 36 35N 18 28N 12 10N N.I. N.I. 34 40S N.I. N.I. N.I. 54 48S 51 37S 45 51S 38 43S 38 03S 34 36S 23 03S 33 40S 34 02S 30 00S 19 05N 13 05N 20 26S 26 09N Longitude 64 41W 66 07W 81 14W 52 40W 88 39W 59 54W 66 07W 73 16W 57 02W 52 01W 80 23W 70 33W 89 57W 76 01W 67 07W 68 52W 30 28N 28 59N 27 07N 26 26N 21 23N 23 36N 24 51N 32 22E 50 50E 56 04E 50 06E 39 10E 58 30E 67 03E 54 09W 68 08W 65 03W 67 25W 62 06W 57 32W 58 22W 14 37E 18 43E 25 33E 31 30E 72 50E 80 17E 57 41E 50 28E 518kHz 490kHz B1 B1 B C,D H O P Q,J U,V W,T X W A F G N R H N.I. N.I. F A N.I. N.I. N.I. A,M B,N C,O D,P E,Q F,R B C I O G P C B X A F G H M P NONE NAV area XI Country China Indonesia Japan Korea,Republic of Malaysia Philippines Singapore Thailand United States Vietnam XII Taiwan Associate Member of IMO Canada United States XIII XIV Russian Federation Station Sanya Guangzhou Fuzhou Shanghai Dalian Jayapura Ambon Makassar Jakarta Otaru Kushiro Yokohama Moji Naha Chukpyun Pyonsan Penang Miri Sandakan Manila Puerto Princesa Davao Singapore Bangkok Radio Guam Ho Chi Minh City Haiphong Danang Chilung Hong Kong Prince Rupert Tofino San Francisco Kodiak Honolulu Cambria Astoria Adak Vladivostok Kholmsk Petropavlovsk Magadan Beringovskiy Provideniya Astrakhan Latitude 18 15N 23 09N 26 02N 31 07N 38 51N 02 31S 03 42S 05 06S 06 06S 43 19N 42 57N 35 14N 34 01N 26 05N 37 03N 35 36N 05 25N 04 25N 05 54N 14 35N 09 44N 07 04N 01 25N 13 44N 13 29N 10 47N 20 44N 16 05N 25 09N 22 13N 54 18N 48 55N 37 56N 57 46N 21 16N 35 31N 46 12N 51 54N 43 07N 47 02N 53 00N 59 40N 63 03N 64 40N 44 20N Longitude 109 30E 113 29E 119 18E 121 33E 121 31E 140 43E 128 12E 119 26E 106 54E 140 27E 144 36E 139 55E 130 56E 127 40E 129 25E 126 29E 100 24E 114 01E 118 00E 121 03E 118 43E 125 36E 103 52E 100 34E 144 50E 106 40E 106 44E 108 13E 121 44E 114 15E 130 25W 125 33W 122 44W 152 34W 158 09W 121 03W 123 57W 176 38W 131 53E 142 03E 158 40E 151 01E 179 20E 173 10W 48 02W 518kHz 490kHz B1 B1 M N O Q R A B D E J K I H G V W U T S J I K C F V X P W W,P P L D H C J,X O Q W X A B C D E F W NONE 1-7 NAV area XV Chile XVI Peru Country Ecuador Station Antofagasta Valparaiso Talcahuano Puerto Montt Punta Arenas Isla de Pascua Paita Callao Mollendo Guayaquil Latitude 23 39S 32 48S 36 43S 41 30S 53 12S 27 09S 05 05S 12 03S 17 01S 02 17S Longitude 70 25W 71 29W 73 06W 72 58W 70 56W 109 25W 81 07W 77 09W 72 01W 79 52W 518kHz 490kHz B1 B1 A,H B,I C,J D,K E,L F,G S U W M Note: The list shows the stations listed at Longwave Navtex Broadcasts (2001-04-16). For details, see the Web side http://www.globalserve.net/~hepburnw/dx/navtex.htm 1-8 2. OPERATION 2.1 Control Description All operation of the NX-300 is carried out with the controls on the front panel of the display unit. FURUNO MENU ENT DISP DIM Omnipad • Shifts cursor and display. • Selects items on menus. PWR Removing the hard cover To remove the hard cover, squeeze it at its top and bottom right (or left) corners and pull it toward you. Pressure Opens menu or message display. Opens message selecting display or navigational data display. MENU ENT Registers items on menus. DISP DIM Adjusts panel dimmer and contrast. Selects 518 kHz or 490 kHz. (See page 2-12.) FREQ PWR Long press: Turns power off. Touch and release: Turns power on. Pressure Figure 2-1 Control panel 2.2 Turning the Power On/Off Turning on: Press the [PWR] key. “NO MESSAGE” (message waiting screen) appears. When a message is received, it appears on the screen and in case of a long message, it scrolls continuously. To confirm version number of the equipment, press the [PWR] key a little longer. Release the key when the following window appears. XX-Version no. Figure 2-2 TURNING ON window Turning off: Press the [PWR] key for 3 seconds. Figure 2-3 TURNING OFF window Note: The NX-300 should be turned on for the duration of a voyage so that important warning messages will not be missed. 2-1 2.3 Adjust Dimmer and Contrast 1. Press the [DIM] key to show the dimmer and contrast setting window. Figure 2-4 DIMMER and CONTRAST setting window 2. Press ! or " for best illumination of the control panel and LCD. 3. Press # or $ for best contrast of the LCD. 4. Press the [ENT] key to close the dimmer and contrast setting window. Note: If you turn off the power with contrast less than 36, contrast is automatically set to 36 when you turn on the power again. 2.4 Menu Operation Overview The menu allows you to custom tailor the NX-300 according to your needs. You can select which categories of message you wish to receive, specify which data to display, etc. 1. Press the [MENU] key to open the main menu. Figure 2-5 Main menu Note: If you press the [MENU] key again at the main menu, the message waiting screen appears. 2. Press ! or " to select menu item. As you operate ! or ", the selected item appears in reverse video. For example, select FUNCTIONS. 3. Press the [ENT] key to open menu selected. Figure 2-6 FUNCTIONS menu 2-2 4. Press ! or " to select menu item and press the [ENT] key. For example, select RCV ALARM. Corresponding option menu appears. Figure 2-7 ON/OFF window 5. Press ! or " to select option desired. 6. Press the [ENT] key to resister your selection. 7 Press the [MENU] key once to return to the menu or twice to quit the menu. 2.5 Selecting Stations The STATION SELECTION menu allows you to select what stations to receive, automatically or manually. In the AUTO mode stations are automatically selected according to the distance between own ship and NAVTEX stations. External navigational data is required to use the AUTO mode. If it is not input, all stations are selected. In the MANUAL mode you can select what stations you wish to receive. Default setting is the AUTO mode. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select STATION SELECTION. 3. Press the [ENT] key. The MODE window appears. Figure 2-8 MODE window 4. Press ! or " to select AUTO or MANUAL as desired. 5. For the AUTO mode, press the [ENT] key to close the menu. For the MANUAL mode, do the following: a) Press the [ENT] key. The STATION SELECTION menu appears. Figure 2-9 STATION SELECTION menu b) c) Press ! or " to select a station you want to change the current setting. Press the [ENT] key to show the following window. Figure 2-10 RECEIVE/IGNORE window 2-3 d) e) f) g) 2.6 Press ! or " to select RECEIVE or IGNORE depending on whether you want to select or deselect the station. Press the [ENT] key. Repeat steps b) to e) to select or deselect other stations. Press the [MENU] key or [DISP] key to close the STATION SELECTION menu. Selecting Messages 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select MESSAGE SELECTION. 3. Press the [ENT] key to show the MESSAGE SELECTION menu. Figure 2-11 MESSAGE SELECTION menu 4. Press ! or " to select a message you want to change the current setting. 5. Press the [ENT] key to show the following window. Figure 2-12 RECEIVE/IGNORE window 6. When you change RECEIVE into IGNORE for message type A, B, D or L, the following window appears to confirm. For all other message types proceed to step 8. Figure 2-13 Ignore message window 7. Press # or $ to select YES or NO. Select YES to change the current setting, or NO not to change. 8. Press the [ENT] key. 9. Repeat steps 4 to 8 to select or deselect other message types. 10. Press the [MENU] key or [DISP] key to close the MESSAGE SELECTION menu. 2-4 2.7 Setting Functions (FUNCTIONS menu) See menu description below for detailed information. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select FUNCTIONS. 3. Press the [ENT] key to display the FUNCTIONS menu. Figure 2-14 FUNCTIONS menu 4. Press ! or " to select menu item and press the [ENT] key. 5. Press ! or " to select option desired. 6. Press the [ENT] key to register your selection. 7. Press the [MENU] key twice to close the menu. 2.7.1 FUNCTIONS menu description RCV NOTIFY: The raw NAVTEX signal can be monitored through the monitor speaker by turning RCV NOTIFY on. The default setting is OFF. RCV ALARM: The audible alarm may be generated when message type A, B, D or L is received. The default setting is ON. KEY BEEP: The equipment can emit a beep tone when a control is operated. The default setting is ON. ERROR RATE: When character error occurs due to noise interference during signal propagation, erroneous character is displayed as “∗”. Error Rate means character error rate and is calculated as followed: Error Rate = number of erroneous characters ÷ total number of characters received × 100 (%) (Total number of characters includes space, line feed, carriage returns, etc.) When the character error rate is within the percentage you set (0-39%), the NX-300 displays the message and stores it. When it exceeds the percentage you set, the NX-300 neither displays nor stores the message. You may set the threshold level of character error rate as desired and the default setting is 33%. 2-5 SCROLLING: This menu item lets you select how to scroll the message display. The default setting is AUTO-SLOW. AUTO-SLOW: Long press of ! or " scrolls line-by-line slowly automatically. Touch and release " to scroll manually. AUTO-FAST: Long press of ! or " scrolls line-by-line automatically, faster than AUTOSLOW. Touch and release " to scroll manually. SKIP-$$: The U.S. National Weather Service broadcasts weather information via the U.S. Coast Guard NAVTEX stations. Their messages contain $$, the continue indicator. You can quickly jump to the next continue indicator. Long press of ! or " skips to $$. SAVE MESSAGE TO PC: Select to download message to a PC. See the next paragraph. 2.7.2 Downloading Messages to a PC Wiring Your equipment provides a wiring diagram that shows how to connect to a PC using a DSUB 9pin connector. Refer to the interconnection diagram for details. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select SYSTEM MENU. 3. Press the [ENT] key to show the SYSTEM MENU. 4. Press " to select WIRING INFO?. 5. Press the [ENT] key to show the wiring info display. Figure 2-15 Connection to PC using a DSUB 9-pin connector A DSUB 25-pin (EIA-232) may also be used to make the connection. In this case the wiring diagram is as follows. 1 2 3 4 5 6 7 RD2 SG SD RD + FG WHITE BLUE YELLOW GREEN RED BLACK - + 7 GND 3 RXD 2 TXD 4 RTS 5 CTS 6 DSR 20 DTR Figure 2-16 Connection to PC using a DSUB 25-pin connector 2-6 Setting for communication software on PC Baud Rate: Character Length: Stop Bit: Parity: X Control: 4800 bps 8 bit 1 bit None XON/XOFF Downloading messages to a PC Set up the computer to receive data. Messages are downloaded to a PC character by character during reception. To download all messages saved in NX-300, do the following; 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select FUNCTIONS. 3. Press the [ENT] key to show the FUNCTIONS menu. 4. Press " to select SAVE MESSAGE TO PC. 5. Press the [ENT] key. The following display appears. Figure 2-17 SAVE MESSAGE TO PC display 6. Press the [ENT] key. Figure 2-18 SAVING START window 7. Set up the computer to receive data. 8. Press # to select YES and press the [ENT] key. 2-7 9. Press the [ENT] key to save. The following messages appear in order. To cancel saving, press the [ENT] key Figure 2-19 SAVING MESSAGES window 10. Press any key to escape. Note1: No message is received during downloading. Note2: When a PC or a serial printer is connected to the NX-300, received messages are displayed on a PC or printed on a serial printer but not displayed or saved to the NX-300 in the following cases; • The NX-300 receives a message it has already saved. • A message is interrupted to receive. 2-8 2.8 Selecting Language You can select language displayed on the NX-300. Languages are English, French, German, Italian, Spanish, Dutch, Danish, and Portuguese. 1. Press the [MENU] key to open the main menu. 2. Press ! to select LANGUGE. 3. Press the [ENT] key. The following menu appears. (ENG: English, FRA: French, GER: German, ITA: Italian, SPA: Spanish, DUT: Dutch, DEN: Danish, POR: Portuguese) Figure 2-20 LANGUAGE menu 4. Use the Omnipad to select language desired. 5. Press the [ENT] key to register your selection and press the [MENU] key to close the menu. 2.9 Display Messages The NX-300 automatically saves and stores up to 132 received messages (However, the memory capacity is limited to 28,000 characters). If memory of the NX-300 is full, messages are deleted on order of time. 1. Press the [DISP] key to show the received messages log. Messages (numbers) are arranged in the order received from latest to earliest, Left to right. The latest message Unread message D type message For A, B or L type message Figure 2-21 Received messages log 2. Operate the Omnipad to select the message to display. If more than 15 messages are saved, the scroll bar appears at the rigth side of the display. Press " or ! to scroll the display. 3. Press the [ENT] key to display the message selected. Note: If you want to see the received frequency (518 kHz or 490 kHz) also, change the window mode as shown on page 4-2. 2-9 2.10 Sample Messages When message is displayed, press ! or " to scroll message and press # or $ to display the other message. When the oldest or newest message is displayed, the beep sounds. ID no. Display indications Start code (sync) Scroll bar Main message Press " to scroll. Main message Termination code Figure 2-22 Sample messages 2-10 2.11 Displaying Navigation Data With navigation data input the NX-300 can display navigation data, in addition to its primary function. 1. Press the [DISP] key to display the receiving messages log. 2. Press the [DISP] key again to display navigation data. Figure 2-23 Nav data display 3. To return to the receiving message log, press the [DISP] key again. 2-11 2.12 Selecting Receive Frequency 1. Press the [FREQ] key to show the frequency window. (Default setting is 518 kHz) Figure 2-24 Frequency window 2. Press or to select receive frequency as appropriate. 3. Press the [ENT] key to close the frequency window. 2-12 3. SYSTEM MENU 3.1 Units of Measurement When navigational data is fed to the NX-300, you can select units of distance and speed to use. Distance/speed can be displayed in nautical miles/knots, kilometers/kilometers per hour, or miles/ miles per hour. The default setting is nautical miles/knots. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select SYSTEM MENU. 3. Press the [ENT] key. The SYSTEM MENU appears. Figure 3-1 SYSTEM MENU 4. Press the [ENT] key. The following window appears. Figure 3-2 UNITS window 5. Press ! or " to select combination desired; nm, kt; km, km/h; mi, mi/h. 6. Press the [ENT] key. 7. Press the [MENU] key or [DISP] key to close the SYSTEM MENU. 3-1 3.2 Time Difference (using local time) GPS uses UTC time. If a GPS receiver feeds nav data to the NX-300 and you would rather use local time, enter the time difference (range: -13:30 to +13:30) between local time and UTC time. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select SYSTEM MENU. 3. Press the [ENT] key to open the SYSTEM MENU. Figure 3-3 SYSTEM MENU 4. Press " to select TIME DIFF. 5. Press the [ENT] key. A cursor circumscribes + or -. This cursor appears whenever selected data can be changed with Omnipad. 6 Press ! or " to display + or -. 7. Press $ to move the cursor to the next column. 8. Press ! or " to select number desired. 9. Repeat steps 7 and 8 to complete. 10. Press the [ENT] key. 11. Press the [MENU] key or [DISP] key to close the SYSTEM MENU. 3-2 3.3 Time Display When navigational data is fed to the NX-300, you may display the time in 12-hour or 24-hour notation. The default setting is 24-hour notation. AM or PM is shown when 12-hour notation is selected. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select SYSTEM MENU. 3. Press the [ENT] key. The SYSTEM MENU appears. 4. Press " to select TIME DISP. 5. Press the [ENT] key. The following window appears. Figure 3-4 TIME DISP window 6. Press ! or " to select 12HOUR or 24HOUR as appropriate. 7. Press the [ENT] key. 8. Press the [MENU] key or [DISP] key to close the SYSTEM MENU. 3.4 Default Setting This function restores all default settings. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select SYSTEM MENU. 3. Press the [ENT] key to show the SYSTEM MENU. 4. Press " to select DEFAULT SETTING. 5. Press the [ENT] key. The following window appears. Figure 3-5 DEFAULT SETTING window 6. Press # to select YES. If you want to cancel, press the [ENT] key to select NO before pressing #. 7. Press the [ENT] key. 8. Press the [MENU] key or [DISP] key to close the SYSTEM MENU. 3-3 3.5 Delete All Messages This function deletes all messages NX-300 saves. 1. Press the [MENU] key to open the main menu. 2. Press ! or " to select SYSTEM MENU. 3. Press the [ENT] key to show the SYSTEM MENU. 4. Press " to select DELETE ALL MESSAGES. 5. Press the [ENT] key. The following window appears. Figure 3-6 DELETE ALL MESSAGES window 6. Press # to select YES. 7. Press the [ENT] key. 8. Press the [MENU] key or [DISP] key to close the SYSTEM MENU. 3.6 User Display of Navigation Data The NX-300 can function as nav data display when connected to navigation equipment. You may choose what data to display in the three cells below the date and time indications on the nav data display. The choices of data are speed, course, range, bearing, power source voltage and position in latitude and longitude (not available for “LEFT” or “RIGHT”). 01-JAN-00 15:37:40 LARGE LEFT RIGHT Figure 3-7 Location of nav data indications 1. Press the [MENU] key to open the main menu. 2. Press " to select USER DISPLAY. 3-4 3. Press the [ENT] key to show the USER DISPLAY menu. The cursor is now on the LARGE field. LARGE means the center indication on the nav data display. Figure 3-8 USER DISPLAY 4. Press the [ENT] key. The following window appears. Figure 3-9 Options for LARGE window 5. Operate the Omnipad to select item desired. (SPD: Speed, CSE: Course, RNG: Range to destination, BRG: Bearing to destination, PWR: Power source voltage, L/L: position in latitude and longitude) 6. Press the [ENT] key. 7. Select the items LEFT and RIGHT and set their options like you did for LARGE, referring to Figure 3-12 for location of indications. Figure 3-10 Options for LEFT, RIGHT 8. Press [DISP] key twice to display the navigation data. The figure below shows display appearance for the setting shown in Figure 3-8. Figure 3-11 Nav data display 3-5 This page is intentionally left blank. 4. OTHER FUNCTIONS 4.1 DEMO Mode The DEMO mode provides simulated operation of this unit. Connection of antenna is not necessary. You may select stations and messages manually or automatically and demo messages are received. All controls are operative. Note: Turning on the DEMO mode erases all messages. Press the [PWR] key while pressing to turn the power on. “SET DEMO MODE!” appears momentarily. “DEMO” appears at the top of the screen when the DEMO mode is active. DEMO mark Figure 4-1 Message display To escape the DEMO mode, press the [PWR] key while pressing . “RESET DEMO MODE!” appears momentarily. 4.2 VIEW Mode The NX-300 ordinarily displays messages in their entirety. The VIEW mode, however displays messages character by character. Press the [PWR] key while pressing to turn the power on. “SET VIEW MODE!” appears momentarily. “VIEW” is displayed at the upper left corner of the display. To quit the VIEW mode,: repeat above procedure. “RESET VIEW MODE!” appears. 4.3 All Clear This function deletes all messages and restores default settings. When the NX-300 is first installed, you should clear all data. Press the [PWR] key while pressing to turn the power on. “RESET BACKUP DATA!” appears momentarily while data is being cleared. Then, all default settings are restored. 4-1 4.4 Changing Received Message Log Window You can show received frequency on the received message log as shown below. 1. Press the [PWR] key while pressing !to turn the power on and release the keys after display appears. 2. Press the [DISP] key to show the received message log. The received frequencies (518 kHz and 490 kHz) are displayed on the window. Figure 4-2 Received message log 3. To restore it, do step 1. 4-2 5. MAINTENANCE & TROUBLESHOOTING WARNING Do not open the equipment. Only qualified personnel should work inside the equipment. Further, watertightness may be reduced. 5.1 Maintenance Check the following points regularly to maintain performance: • Check that connectors on the rear panel are firmly tightened and free of rust. • Check that the ground system is free of rust and the ground wire is tightly fastened. • Check that battery terminals are clean and free of rust. • Check the antenna for damage. Replace if damaged. • Dust and dirt on the keyboard and display screen may be removed with a soft cloth. Do not use chemical cleaners to clean the equipment; they may remove paint and markings. 5.2 Diagnostic Test The diagnostic test checks ROM, RAM, data port, battery, keyboard and LCD for proper operation and displays program numbers. 1. Press the [MENU] key to open the main menu. 2. Press the ! or " to select SYSTEM MENU. 3. Press the [ENT] key to show the SYSTEM MENU. 4. Press ! or " to select TEST. 5. Press the [ENT] key. You are asked if you are ready to start the test. Figure 5-1 TEST window 6. Press the # to select YES. 5-1 7. Press the [ENT] key to start the test. The equipment checks ROM, RAM, SIO and internal battery, and the results are individually displayed as OK or NG (No Good). Program numbers appear at the bottom of the display. Note 1: SIO requires a special connector to check. “03” appears as the result when no connector is connected. Note 2: CNT is the number of times test has been consecutively executed. Program no. Figure 5-2 TEST display After the equipment has checked the items shown in Figure 5-2, a beep sounds and the message PUSH KEY appears at the top right-hand corner. 8. Press each key one by one. The name of the key pressed momentarily appears at the top of right-hand corner if the key is functioning properly. Note: If no key is pressed within approx. five seconds, the equipment automatically displays the following message to inform you that it is now going to check the LCD. Figure 5-3 LCD CHECK display 9. The test repeats. Turn off the power to stop the test. 5.3 When the Battery Icon Appears A lithium battery (type: CR2354-1F2, code no.: 000-142-305) is installed on the circuit board inside the display unit, and it preserves data when the power is turned off. The life of the battery is about 5-10 years. Its voltage is checked when the power is turned on. When its voltage is low the battery icon appears on the display to alert you. When this happens, contact your dealer to request replacement of the battery. Note: When the battery is dead, all default settings are restored. 5-2 5.4 Replacement of Fuse The 1 A fuse in the snap-in fuse holder on the power cable protects the equipment from equipment fault and reverse polarity of the ship’s mains. If the fuse blows find out the cause before replacing it. If the fuse blows again after replacement, contact a FURUNO agent or dealer for advice. Use only a 1 A fuse – use of a different fuse will damage the equipment and void the warranty. CAUTION Use the proper fuse. Use of a wrong fuse can cause fire or equipment damage. 5-3 This page is intentionally left blank. 6. INSTALLATION 6.1 Installation of Display Unit Mounting considerations The display unit can be installed on a tabletop, on the overhead, or in a panel (optional flush mounting kit required). Refer to the outline drawings at the end of this manual for installation instructions. When selecting a mounting location, keep in mind the following points: • Locate the unit away from exhaust pipes and vents. • The unit is waterproof thus it can be installed outdoors. However, locate it of direct sunlight, (or in a suitable, ventilated enclosure) to prevent heat which can build up inside the cabinet. • The mounting location should be well ventilated. • Mount the unit where shock and vibration are minimal. • Allow sufficient maintenance space at the sides and rear of the unit and leave sufficient slack in cables, to facilitate maintenance and servicing. • Observe the following compass safe distances to prevent deviation of a magnetic compass; Standard compass, 0.5 m, Steering compass, 0.3 m. • After you install this equipment, perform All Clear as in paragraph 4.3 on page 4-1. Tabletop overhead mounting Tabletop Overhead Figure 6-1 Tabletop and overhead mounting methods Flush mounting There are two types of flush mounting kits. For details, see the outline drawings at the end of this manual. 6-1 6.2 Installation of Antenna Unit Mounting considerations Install the antenna unit referring to the antenna installation diagram at the end of this manual. When selecting a mounting location for the antenna unit, keep in mind the following points: • Do not shorten the antenna cable (10 m cable fitted to the antenna). • The length of the whip antenna for the NX-3E should be no longer than 1.2 m and no larger than 5 mm in diameter to prevent antenna damage. Do not use a 2.5 m whip antenna. Use spring washer (supplied) for whip antenna. • The NX-300 contains a very sensitive receiver. To avoid mutual interference with other radio equipment, do not install this unit near an SSB/VHF/CB radiotelephone. • If the antenna cable is to be passed through a hole which is not large enough to pass the connector, you may unfasten the connector with a needle nose pliers and 3/8-inch open-end wrench. Refasten it as shown in Figure 6-2, after running the cable through the hole. • If you install the antenna unit except the NX-3E and the NX-3H, contact your dealer. Washer Clamp nut Gasket (reddish brown) Shield Center pin (soldered) Connector shell Figure 6-2 How to assemble the connector 6-2 6.3 Wiring The figure below shows where to connect cables on the rear of the display unit. ANTENNA UNIT NX-3H-D NAVTEX RECEIVER ANT 10 m 2m POWER (12-24 VDC) Ground 1 A FUSE (+ Line) Black - + Red To personal computer To navigational equipment Figure 6-3 Wiring Note: The fuse holder contains a spring that fixes the fuse. To prevent detachment of the spring, which would cause loss of power, tie the line as shown in Figure 6-4. Fuse holder + line (red) Tie here. Figure 6-4 How to fix spring in fuse holder 6-3 Grounding • The ground wire (local supply) should be 1.25 sq or larger for Navtex Receiver. The ground wire should be as short as possible. • The signal ground and frame ground are separated, however the power line is not isolated. Therefore, if connecting other equipment which has signal ground connected to frame ground, the earth lamp will light. Especially, for positive ground battery separate the frame ground of the external equipment from the earth. If not, the equipment may be damaged. External equipment The power supply port is commonly used for connection of external equipment such as navigation equipment or a PC. Refer to the interconnection diagram on page S-1 for connection. 6.4 Interfacing This equipment can receive navigation data in RS-232C format. For example, it can receive position data from GPS navigator GP-31/GP-36 for display on its screen. If you want to connect equipment which outputs data in a format other than RS-232C, a level converter is required for interface. Consult FURUNO dealer for details. Input data sentence description GGA: GPS position fixing condition (time of fix, latitude, longitude, receiving condition, number of satellites used, DOP) GLL: Latitude and longitude RMB: Generic navigational information (cross track error, steering direction, starting waypoint no., destination waypoint no., latitude and longitude of starting waypoint, latitude and longitude of destination waypoint, range and bearing to waypoint, range and bearing from present position to destination waypoint, velocity to destination, arrival alarm) ZDA: 6-4 Time and date MENU TREE MENU Default settings in boldface italic. STATION SELECTION MODE (AUTO, MANUAL) MESSAGE SELECTION (A-E, L, V: RECEIVE; OTHERS: IGNORE) FUNCTIONS RCV NOTIFY (OFF, ON) RCV ALARM (OFF, ON) KEY BEEP (OFF, ON) ERROR RATE (0-39 33%) SCROLLING (AUTO-SLOW, AUTO-FAST, SKIP-$$) SAVE MESSAGE TO PC SYSTEM MENU UNITS (nm, kt; km, km/h; mi,mi/h) TIME DIFF (-13:30 - +13:30, +00:00) TIME DISP (12HOUR, 24HOUR) DEFAULT SETTING DELETE ALL MESSAGES TEST WIRING INFO? USER DISPLAY LARGE (SPD, CSE, RNG, PWR, L/L) LEFT (SPD, CSE, RNG, BRG, PWR) RIGHT (SPD, CSE, RNG, BRG, PWR) LANGUAGE(ENG, GER, SPA, DEN, FRA, ITA, DUT, POR) AP-1 SPECIFICATIONS OF THE NAVTEX RECEIVER NX-300 1. RECEIVER UNIT 1.1. Receiving Frequency 518 kHz or 490 kHz 1.2. Mode of Reception F1B 1.3. Sensitivity 2 µV e.m.f. (50 ohms), 4% error rate 1.4. Message Category A: Navigation warning B: Meteorological warning C: Ice report D: Search and rescue information/ piracy and armed robbery E: Meteorological forecast F: Pilot message G: Decca message H: Loran-C message I: Omega message J: Differential omega message K: Other electronic navigational aid and system message L: Navigational warning (additional) M to Y: Reserved – presently not used V: Notice to Fishermen (US only) Z: QRU (no message on hand) 2. DISPLAY UNIT 2.1. Display System 4.5-inch (95 x 60 mm) Monochrome LCD, 120 x 64 pixels 2.2. Display Modes Message Selection Mode, NAV Data Mode, Message Display Mode 2.3. Message Storage 28,000 Characters 3. ANTENNA UNIT 3.1. Selectable Antenna NX-3H-D: H-field antenna for NX-300-H-D Others: Local supply antenna for NX-300-N-D 3.2. Input Impedance 50 ohms 3.3. Power supply +5.0 VDC 4. INTERFACE 4.1. Input Data NMEA0183 Ver.1.5/2.0, RS-232C, 4800 bps GGA, GLL, RMB, ZDA SP - 1 E5629S01C 4.2. Output Data Message data for personal computer, RS-232C, 4800 bps Data length: 8, Stop bit: 1, Parity: None T/R Code: CR+LF, XON/XOFF Control, Local echo: ON 5. POWER SUPPLY 12-24 VDC: 130-70 mA 6. ENVIRONMENTAL CONDITION 6.1. Ambient Temperature Antenna unit: -25°C to +70°C Display Unit: -15°C to +55°C 6.2. Relative Humidity 95% at 40°C 6.3. Water proofing Antenna unit: IEC-IPX6 Display unit: IEC-IPX5 6.4. Vibration ±1 mm ±10%, 5 to 13.2 Hz, Maximum acceleration 7 m/s2, 13.2 to 100 Hz (IEC 60945) 7. COATING COLOR 7.1. Display Unit Chassis: 2.5GY5/1.5, Panel N3.0 7.2. Antenna Unit N9.5 SP - 2 E5629S01C This page is intentionally left blank. A-1 PACKING LIST 08AU-X-9852 -2 1/1 NX-300-H-D N A M E ユニット O U T L I N E DESCRIPTION/CODE № Q'TY UNIT NX-3H-D 空中線部 1 ANTENNA UNIT 000-059-204 NX-300-D ナブテックス受信機 1 NAVTEX RECEIVER 000-059-205 予備品 SPARE PARTS FGMB 1A 125V ヒューズ 2 FUSE 000-114-805 付属品 ACCESSORIES FP14-02801 20-016-1091-2 保護カバー 1 COVER 100-297-032 工事材料 INSTALLATION MATERIALS MJ-A7SPF0005-020 ケーブル組品MJ 1 CABLE ASSY. 000-139-384 5X20 SUS304 1シュ +トラスタッピンネジ 4 +TAPPING SCREW 000-802-081 (略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) C5629-Z02-C A-2 PACKING LIST 08AU-X-9853 -3 1/1 NX-300-N-D N A M E ユニット O U T L I N E DESCRIPTION/CODE № Q'TY UNIT NX-300-D ナブテックス受信機 1 NAVTEX RECEIVER 000-059-205 予備品 SPARE PARTS FGMB 1A 125V ヒューズ 2 FUSE 000-114-805 付属品 ACCESSORIES FP14-02801 20-016-1091-2 保護カバー 1 COVER 100-297-032 工事材料 INSTALLATION MATERIALS MJ-A7SPF0005-020 ケーブル組品MJ 1 CABLE ASSY. 000-139-384 5X20 SUS304 1シュ +トラスタッピンネジ 4 +TAPPING SCREW 000-802-081 . (略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) INDEX A L All clear 4-1 Language menu 2-9 AUTO 1-3 LCD check 5-2 AUTO mode 2-3 Local time 3-2 AUTO-FAST 2-6 M AUTO-SLOW 2-6 Main menu 2-2 B Maintenance 5-1 BATTERY icon 1-3, 5-2 MANUAL mode 2-3 C Message selection 2-4 Contrast 2-2 Mounting 6-1 Control panel 2-1 N D Navarea 1-1 Data sentence 6-4 Navigation data display 2-11, 3-4 Default setting 3-3 NAVTEX area 1-1 Deleting all messages 3-4 NEW 1-3 DEMO mode 4-1 O Dimmer 2-2 Omnipad 2-1 E P ERROR RATE 2-5 Power on/off 2-1 F Program version no. 5-2 FUNCTIONS menu 2-5 R G RCV ALARM 2-5 Grounding 6-4 RCV NOTIFY 2-5 I Rx 1-3 Installation 6-1 K KEY BEEP 2-5 Index-1 S SAR 1-3 Saving to PC 2-6 Scroll bar 1-3 SCROLLING 2-6 SKIP-$$ 2-6 Start code 1-2 Station list 1-5 Station map 1-4 Station selection 2-3 SYSTEM MENU 3-1 T Termination code 1-2 TEST 5-1 TIME DIFF 3-2 Time difference 3-2 TIME DISP 3-3 Type of message 1-2 U Units of measurement 3-1 User display 3-4 V Version no. 2-1 VIEW mode 4-1 W WARNING 1-3 Wiring 2-6, 6-3 Index-2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Modify Date : 2002:12:10 16:42:40-08:00 Create Date : 2000:03:30 14:23:50+09:00 Page Count : 60 Page Mode : UseOutlines Has XFA : No Mod Date : 2002:05:21 09:37:44+09:00 Creation Date : 2000:03:30 14:23:50+09:00 Producer : Acrobat Distiller 4.0 for Windows Metadata Date : 2002:05:21 09:37:44+09:00EXIF Metadata provided by EXIF.tools