Fusion Electronics Car Amplifier En At1100 Users Manual
EN-AT1120 to the manual 3da5fe3b-4466-47b4-9d5d-40a24b0ec74b
2015-02-09
: Fusion Fusion-Fusion-Electronics-Car-Amplifier-En-At1100-Users-Manual-552797 fusion-fusion-electronics-car-amplifier-en-at1100-users-manual-552797 fusion pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
ENCOUNTER ACTIVE ENCLOSURES EN-AT1100, EN-AT1120 Disclaimer The provided self adhesive feet are intended for initial site placement only, and are not to be considered a suitable method of securing the Active Enclosure. Always ensure the Active Enclosure is securely attached, to avoid movement. FUSION accepts no responsibility for damage or injury in relation to inappropriate securing of this product Product Specifications EN-AT1100 EN-AT1120 Max Power Rating 300 Watts 360 Watts Frequency Repsonse 35Hz - 250Hz 30Hz - 250Hz Bass Boost (Variable) 0 / + 18dB 0 / + 18dB Low Pass Filter (Variable) 40Hz - 250Hz 40Hz - 250Hz Tuning Bass Reflex Bass Reflex Woofer Size 10” 12” Fuse 15 Amp 15 Amp Tube Dimensions 550mm x 306mm x 306mm 21 11/16” x 12 1/16” x 12 1/16” 590mm x 365mm x 365mm 23 1/4” x 14 3/8” x 14 3/8” Control Descriptions LEVEL This allows the adjustment of the amplifier level of the subwoofer. Turn clockwise to increase the level. If the sound becomes distorted reduce the level. LOW PASS FILTER (LPF) This allows the adjustment of the highest frequency the Encounter Active Enclosure Tube will produce. This should be adjusted to blend with your main speakers. Typically, this will be set to around 100Hz (approximately the central position of the control knob). BASS This allows very low frequencies to be boosted. Adjust with care and listen for distortion. If the sound becomes distorted, reduce the amount of boost. REMOTE LEVEL CONTROLLER When connected, this allows further control over the level from a remote location, using the supplied lead. Installation Make sure the Encounter Active Enclosure is firmly fixed in your vehicle. Check before drilling or cutting holes. DO NOT work near gas tanks, fuel lines, hydraulic lines or electrical wiring. DO NOT mount the Encounter Active Enclosure in such a way as to pinch or damage the wires. Make sure everything is firmly connected, before attaching the +12V wire. Make sure the +12V wire is fused as close as possible to the battery. ALWAYS use a fuse with the recommended rating. Two types of self-adhesive feet are included in the packaging. The rubber feet are to protect the bottom of the enclosure, or the surface it is mounted to. There are four feet, which correspond to four indentations (feet and indentations are the same shape) in the bottom of the enclosure end plates. Peel off the paper covering the rubber feet, and adhere to the indentations. There are also four Velcro feet (both hook and eye parts, both with self-adhesive properties) included. These are for assisting in fixing the location of the enclosure. Peel off the paper covering and adhere one part to the indentations in the enclosure end plates, and the matching part to the mounting surface. Always clean the surfaces before applying the adhesive part Wiring • Connect the ground wire to the vehicle first (clean dirt and paint to bare metal). • Connect the 12 volt (red wire) to the positive battery terminal. Make sure the fuse is close to the battery. • Connect the remote on (blue wire) • Connect the RCA cables if applicable, OR • Connect the speaker level wire by splicing into the headunits speaker wires. See Note 1 • Connect the remote level controller with the supplied lead. • Check all connections. • Finally, connect the power plug end of the power harness to the unit. *Note 1 Take care to make sure the wires are spliced in the correct phase. Positive to positive, negative to negative. Failure to do this correctly could result in loss of bass. Speaker Level Input Plug FUSE HIGH INPUT REMOTE LOW INPUT Right LEVEL L.P.F BASS POWER PROT Left REM +12 L+ R+ L- R- Power Plug GND POWER MIN MAX 40Hz 250Hz 0dB 18dB Connect black wire to chassis ground of vehicle (Ground) See note 1 Splice into source unit’s speaker wires (R+) Grey/White (R- ) Grey (L+ ) Green/White (L- ) Green Connect the remote level controller lead to the amplified tube EN-AT110 Connect red wire to positive (+12V) battery terminal Connect blue wire to source unit’s accessory lead or switched 12 volt source (REM) Positive Vehicle Battery Remote Level Controller For further product and installation information please visit www.fusionelectronics.com Para obtener más información sobre los productos o su instalación, visite www.fusionelectronics.com Weitere Informationen zum Produkt und zur Installation finden Sie auf folgender Website: www.fusionelectronics.com Ga naar www.fusionelectronics.com voor meer product- en montage-informatie Pour plus de renseignements sur les produits et l’installation, veuillez consulter www.fusionelectronics.com Per ulteriori informazioni su prodotto e installazione, potete visitare www.fusionelectronics.com За дополнительной информацией о продукции и установке обращайтесь на www.fusionelectronics.com Specifications and design are subject to change without notification RECORD YOUR PURCHASE DETAILS HERE: MODEL NUMBER __________________________ DATE OF PURCHASE__________________________ AFFIX RECEIPT HERE WARNING! Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE! V 2.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1.1-111 Instance ID : uuid:dd1c3995-f1e9-4c34-8c85-69c9afb79683 Document ID : adobe:docid:indd:d074c3c8-4d43-11dd-928d-e4965edd1d93 Rendition Class : proof:pdf Derived From Instance ID : 2cc66ed0-db61-11dc-b9af-bbf4d0b3e5bd Derived From Document ID : adobe:docid:indd:064a9c75-db4f-11dc-b119-f1bca7ac7ecd Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches Manifest Reference Instance ID : uuid:E88E8B38699D11DB81789F7B3CB99915, uuid:E88E8B38699D11DB81789F7B3CB99915, uuid:7b02228e-c154-11db-8008-000393ac1f30 Manifest Reference Document ID : uuid:E88E8B37699D11DB81789F7B3CB99915, uuid:E88E8B37699D11DB81789F7B3CB99915, uuid:77dbee01-b707-11db-a842-003065ed47be Create Date : 2008:07:09 14:02:42+12:00 Modify Date : 2008:07:09 14:02:43+12:00 Metadata Date : 2008:07:09 14:02:43+12:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9698 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools