User Manual-P. 38-175 Rev.01(0128)
Common function The setting screens are called from the following menu. All the functions common to airplane, helicopter, glider, and multi-copter model types are shown here. â First set the throttle to slow. â Then turn on the power. ďźHome screenďź â W hen t h e E N D k e y i s pressed, the display returns to the home screen. END ďź Common function ďź1 secondďź â When the + key is pressed for 1 second, the menu screen is displayed. MENU 0(18ĺ˛ĺ˛ĺ˛ĺ˛1 MENU 1/3 ăŁ0'/6(/ ăŁ0'/1$0( ăŁ)$,/6$)( ăŁ5(9(56( ăŁ7,0(5 ăŁ6(592 ăŁ(1'32,17 ăŁ75,0 ăŁ68%75,0 ăŁ30,; ăŁ$8;&+$1 ăŁ3$5$0(7(5 0(18ĺ˛ĺ˛ĺ˛ĺ˛12 MENU 2/3 ăŁ7(/(0(75< ăŁ6(1625 ăŁ6%86/,1. ăŁ0'/75$16 ăŁ75$,1(5 ăŁ$,/',)) ăŁ$,/âŤÚâŹ58' ăŁ97$,/ ăŁ*<526(16 ăŁ(/(921 ăŁ$,/9$725 ăŁ7+5âŤÚâŹ1(('/ 0(18ĺ˛ĺ˛ĺ˛ĺ˛123 0(18ĺ˛ĺ˛ĺ˛ĺ˛1 23 MENU 3/3 38 To menu screen by holding down the + key ăŁ'5(;32 ăŁ)/$3(521 ăŁ$,5%5. ăŁ)/$3âŤ(ÚâŹ/( ăŁ(/(âŤ)ÚâŹ/$3 ăŁ)/$375,0 ăŁ7+5&87 ăŁ,'/('2:1 ăŁ61$352// ăŁ7+5&859( ăŁ3,7&859( ăŁ7+5ĺ˛'(/$< ďźSelectionďź â Move the cursor ( h i g h l i g ht e d ) u p a n d down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. ďźCalling the setting screenďź â Press the Jog key to open the setting screen. key ďź LCD âďź key ââ key âJog key âEND key â Function MENU1/3 (P.40) TELEMETRY (P.66) Model select ďź Model Copy ďź Data reset ďź RX ďź Link Telemetry Display ďź Alarm setup MDL-NAME Telemetry sensor (P.43) Model name ďź User name FAIL SAFE (P.45) Fail safe REVERSE (P.47) Servo reverse TIMER (P.48) SENSOR SBUS LINK (P.83) (P.89) S.BUS servo set up MDL-TRANS (P.92) Data transfer of another 10J or 8J TRAINER Trainer (P.93) Common function MDL-SEL MENU2/3 Timer SERVO (P.49) Servo monitor ďź Servo test END POINT (P.50) End point TRIM (P.51) Trim reset ďź Trim step SUB TRIM (P.52) Sub trim P.MIX1-6 (P.53) Program mixing 1 âź 6 AUX-CHAN (P.56) AUX channel PARAMETER (P.58) Data reset ďź Model type ďź ATLtrim ďź LCD contrast ďź Back light : mode, time, adjustment ďź Home display ďź Battery alarm ďź Battery vibration ďź Buzzer tone ďź Jog navi ďź Jog light ďź Jog time ďź Telemetry : mode, unit ďź Speech : language, volume ďź Stick position alarm 39 MDL-SEL Model selectďźselect ďź copy ďź reset ďź RX type ďź linkďź (Common) Function This function is used when calling and copying model data stored in the transmitter. The selected model data can also be reset. System changes (T-FHSS Air, S-FHSS) matched to the receiver type and linking with the receiver are also done here. Model selectďźSELECTďź The model data of up to 30 models can be stored in the transmitter. This function is used when calling saved model data. Model copyďźCOPYďź This is the model data copy function. It is convenient when you want to store model data as backup or build a number of models with the same data settings. â The data of the model memory currently in use can be copied to another model memory. Data resetďźRESETďź The model data currently in use can be reset to its initial value. However, it does not Reset other than the following of a parameter. [ The function reset in a parameter : ATL trim, TELEMETRY mode, STK POSI ALRM ] Receiver selectionďźRXďź Common function The R3008SB supplied with the transmitter, employs the T-FHSS Air system. When you want to use an S-FHSS receiver, switch to S-FHSS here. However, the telemetry function cannot be used with the S-FHSS system. LinkďźLINKďź When linking with the receiver, the transmitter is set to the link mode here. The ID number of the currently linked receiver is displayed. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź Model copy Data reset RX system Link 40 ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź Model select â Select the setting item with the Jog key. ⥠Select "MDL-SEL" from the menu with the Jog key. MDL-SEL 6(/(ăŁ02'(/ &23<ăŁ02'(/ 5(67ăŁ([HFXWH 5;ăŁ7)+66$LU /,1.ăŁ,' XXXXXXXXX ďźModel numberďź1 âź 30ďź â Original data : Model type Model name â Copy place : Model type Model name â SystemďźT-FHSS Air or S-FHSS) â Link receiver ID Model select â Select the SELECT item and then select the model number by pressing the + key or â key. ďź âĄ P r e s s t h e Jog key f o r 1 second. ⢠Select the model by pressing the Jog key. ďź1 secondďź â or Selection rangeďź1 âź 30 â ConďŹrmation message "sure?" blinks. â A confirmation "beep beep" sounds to show that selection is complete. For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. Model copy â Select the COPY item and the select the model number of the copy destination by pressing the + key or â key. ďź âĄ P r e s s t h e Jog key f o r 1 second. ďź1 secondďź â or ⢠Copy the model by pressing the Jog key. Selection rangeďź1 âź 30 â A confirmation "beep" sounds and "COMPLETE" is displayed on the screen to show that copying is complete. For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. Common function â ConďŹrmation message "sure?" blinks. Date reset â Select the REST item and then press the Jog key for 1 second. ⥠Date reset by pressing the Jog key. ďź1 secondďź â ConďŹrmation message "sure?" blinks. â A confirmation "beep" sounds and "COMPLETE" is displayed on the screen is complete. For safety, a double setting system is used. When a change is cancelled after the conďŹrmation message is displayed, the change is not made when moved to another setting item by Jog key. CAUTION Only the throttle channel (CH3) initial setting is REV (reverse). Thoroughly check the Hi and Low directions of the engine or motor used and be careful that they do not suddenly run at full speed. Even after data reset, CH3 is reversed. 41 RX type â Select the RX item and then select T-FHSS Air or S-FHSS by pressing the + key or â key. ďź âĄ RX type change by pressing the Jog key. â ConďŹrmation message "sure?" blinks. â or â A confirmation "beep" sounds is complete. Selection rangeďźT-FHSS Air, S-FHSS For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. Link â Select the LINK item and then press the Jog key for 1 second. ďź1 secondďź Common function 42 â T-FHSS Air only. S-FHSS does not enter the link mode. Use the receiver link button to link the receiver. ⥠Enters the link mode for about 20 seconds. During this time, bring the receiver near the transmitter and turn on the receiver power. When linking, the receiver ID is displayed. â In the link mode, a confirmation "beep beep beep" sounds and the time remaining is displayed on the screen. W h e n 20 s e c o n d s h a v e e l a p s e d , a continuous beep sounds and the link mode is exited. For safety, linking must not be performed while the drive motor or engine is running. When linking is complete, turn the power oďŹ and on and check operation. MDL-NAME Model name ďź User name (Common) Function A model name is inputted into each model in T10J. User name is inputted into T10J. Model name settingďźMDL NAMEďź This function assigns a name to the model data. The model name is displayed on the top row of the home screen. This serves to prevent model memory mistakes if the current aircraft name or other name is entered. â Up to 10 characters can be set. User name settingďźUSR NAMEďź The user name displayed on the home screen can be set. (When a user name is not set, the Futaba logo is displayed) When the home screen display is changed to USR-NAME by PARAMETER, the set user name is displayed on the home screen. â Up to 10 characters can be set. Method â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "MDL-NAME" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź Common function Calling the setting screen ďźResetďź MDL-NAME Model name ďźCandidate charactersďź â Characters that can be entered ; Numeric/upper case alphabet/ lower case alphabet User name Model name â Move the cursor to the model name digit you want to change by pressing the + key or â key. ďź â ⥠Move the cursor to the candidate character you want to change with the Jog key. ⢠Change the character by pressing the Jog key. or Set the model name by repeating steps â to ⢠above. Reset methodďźWhen the cursor is moved to any digit of the model name by + key or â key and the Jog key is pressed in the state in which the cursor was moved to RESET by Jog key, the model name returns to its initial setting. 43 User name â Move the cursor to the user name digit you want to change by pressing the + key or â key. ďź or â ⥠Move the cursor to the candidate character you want to change with the Jog key. ⢠Change the character by pressing the Jog key. Set the user name by repeating steps â to ⢠above. Reset method: When the cursor is moved to any digit of the user name by + key or â key and the Jog key is pressed in the state in which the cursor was moved to RESET by Jog key, the user name returns to its initial setting (Futaba logo). Displaying the user name on the home screen The set user name can be displayed on the home screen. (When a user name is not set, the Futaba logo is displayed.) When the home screen display is changed to USR-NAME by PARAMETER, the set user name is displayed. Common function Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "PARAMETER" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ⥠Select "USR-NAME" by pressing the + key or â key. ⢠End setting by pressing the END key. ďź1 secondďź Parameter â Select "HOME-DSP" from the parameter 2 page with the Jog key. ďź 44 â END Fail safe FAIL SAFE (Common) Function When normal radiowaves cannot be received due to noise and interference, the NOR mode, which holds the servo of each channel in its position immediately before reception was lost, or F/S (Fail Safe) mode, which moves the servo of each channel to a preset position, can be selected. When T-FHSS Air is selected, the battery fail safe voltage can be set. Ĺ:KHQ WKH WKURWWOH FKDQQHO ZDV UHYHUVHG E\ VHUYR UHYHUVH IXQFWLRQ WKH )6 GDWD LV DOVR UHYHUVHG 7KURWWOH FKDQQHO RQO\ ,I WKH UHFHLYHU EDWWHU\ YROWDJH GURSV EHORZ WKH VHW YDOXH ZKHQ WKH IDLO VDIH PRGH ZDV VHOHFWHG WKH EDWWHU\ IDLO VDIH IXQFWLRQPRYHVWKHVHUYRWRDSUHVHWSRVLWLRQ Ĺ7KH6)+66IDLOVDIHYROWDJHLV9 Ĺ2QO\WKHWKURWWOHFKDQQHOEDWWHU\IDLOVDIHIXQFWLRQ FDQEHWXUQHGRQDQGRII Method Ĺ:KHQWKLVIXQFWLRQZDVSHUIRUPHGUHVHWWKHEDWWHU\ IDLO VDIH IXQFWLRQ E\ WKH IROORZLQJ PHWKRG DQG LPPHGLDWHO\ODQG Reset methodďź T h e ba ttery fa il sa fe fun c tion c a n be temporarily disabled by moving the throttle stick to the slowest side. However, after 30 seconds the battery fail safe function will return to the battery fail safe state. WARNING For safety, always set the fail safe functions. Ć5HPHPEHUWRVHWWKHWKURWWOHFKDQQHOIDLOVDIHIXQFWLRQVRWKDW the servo moves to the maximum slow side for airplanes and to the slow side from the hovering position for helicopters. Crashing of the model at full high when normal radio waves cannot be received due to interference, etc., is very dangerous. Ć,IWKHEDWWHU\IDLOVDIHLVUHVHWE\WKHWKURWWOHVWLFNLWPD\ be mistaken for an engine malfunction and will be reset at WKURWWOHVORZDQGWKHPRGHOZLOOFRQWLQXHWRĂ\,I\RXKDYH any doubts, immediately land. â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "Fail safe" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź F/S Position Mode select â Select the setting item with the Jog key. FAIL SAFE 1: 2: 3: 4: 5: AIL ELE THR RUD GER 1 2 3 TFHSS Common function Calling the setting screen B-F/S : ON/OFF MODE. POSI B-F/S ăŁNOR ăŁ125 20% ACT ăŁ)6 ăŁ125 ăŁ125 Fail safe â Mode selection â Select the mode by pressing the + key or â key at the MODE item of each channel. ďź â or ďźRangeďź NOR, F/S ďźWhen F/S mode was selectedďź â F/S position â When using the B-F/S mode ⥠In the mode selected state, set the F/ S position by holding the stick of that channel in the position you want to set and press the Jog key for 1 second. â Select ACT by pressing the + key or â key at the B-F/S item. â A conďŹrmation beeping sounds to show that the servo position was set. ďź â or ďźRange ďź Defaultďź INH, ACT ďź INH 45 Battery fail safe voltage setting â Select BATTERY F/S VOLTAGE on page 3 of the fail safe screen with the Jog key. ⥠Set the voltage by pressing the + key or â key. ďź â ďźSet up rangeďź 3.8V 4.0V 4.2V 4.4V 4.6V 4.8V 5.0V 5.3V 5.6V 5.9V 6.2V 6.5V 6.8V 7.1V 7.4V Common function 46 ⢠End setting by pressing the END key. END REVERSE Servo reverse (Common) Function Servo reversing (REVERSE): changes the direction an individual servo responds to a &21752/67,&.PRWLRQ For CCPM helicopters, be sure to read the section on SWASH AFR before reversing any servos. With the exception of CCPM helicopters, always complete your servo reversing prior to any other programming. When using ACRO functions that control PXOWLSOHVHUYRVVXFKDV)/$3(521RU97$,/LW may be confusing to determine whether the servo needs to be reversed or a setting in the function needs to be reversed. Refer to the instructions for each specialized function for further details. CAUTION Only the throttle channel (CH3) initial setting is REV (reverse). Thoroughly check the Hi and Low directions of the engine or motor used and be careful that they do not suddenly run at full speed. Since the direction of the ailerons of an airplane can be easily mistaken, be very careful. Method Calling the setting screen ďź âĄ Select "REVERSE" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź To prevent erroneous setting, after the servo reverse screen was called as described above, the channel will not be selected if the Jog key is not pressed at the left and right. Channel select â Select the channel with the Jog key. REVERSE A E T R G F A A A A I L H U E L U U U U L E R D R P X X X X REV NOR 1 2 3 4 5 6 7 8 9 10 Common function â Call the menu screen from the home screen by pressing the + key for 1 second. â The currently selected channel is highlighted. â Display Reverse/Normal REVďźReverse NORďźNormal ďźChannel numberďź Servo Reverse â Channel is Select by Jog key. Selection rangeďź1 âź 10ch ⥠NOR or REV is chosen by Jog key. â The confirmation message "sure?" blinks on the screen. (Not displayed if the same as before.) ⢠Reverse the servo by pressing the Jog key. â A c o n fi r m at i o n b e e p i n g sounds and the direction of operation is reversed. For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. 47 TIMER Timer (Common) Function The timer is convenient during a competition to VHWWKHVSHFLÂżHGDPRXQWRIWLPHRUWKHĂ\LQJWLPH on a full tank of fuel. Ĺ7ZRWLPHUV\VWHPVFDQEHVHW7LPHU705!DQG 7LPHU705! Ĺ7KH WLPHUV FDQ EH VHW IRU HDFK PRGHO 6LQFH WKH WLPHUVFDQEHVHWWRPDWFKWKHPRGHOWKH\GRQRW KDYHWREHUHVHWHDFKWLPHWKHPRGHOLVFKDQJHG Ĺ7KH W\SH RI WLPHU FDQ EH VHOHFWHG IURP DPRQJ XS 83 GRZQ '2:1 DQG GRZQ VWRS '1673 7KHXSWLPHULVFRXQWHGXSIURPDQGWKHHODSVHG WLPHLVGLVSOD\HGRQWKHVFUHHQ7KHGRZQWLPHULV FRXQWHGGRZQIURPWKHVHWWLPHDQGWKHUHPDLQLQJ WLPH LV GLVSOD\HG RQ WKH VFUHHQ 7KH GRZQ VWRS WLPHUVWRSVWKHFRXQWDW(DFKWLPHUFDQEHVHW XSWRPLQXWHVVHFRQGV Ĺ6ZLWFKHV $ WR + WKURWWOH VWLFN 677+5 RU SRZHU VZLWFK 3:56: FDQ EH VHOHFWHG DV WKH VWDUW VWRS VZLWFK 216: 7KH 212)) GLUHFWLRQ FDQ DOVREHVHW+RZHYHUZKHQWKHSRZHUVZLWFKZDV VHOHFWHGWKHWLPHUVWDUWVZKHQWKHSRZHUVZLWFKLV WXUQHGRQ Ĺ:KHQ WKH WLPHU \RX ZDQW WR UHVHW LV VHOHFWHG ZLWK WKH -RJ NH\ DQG WKH -RJ NH\ LV SUHVVHG IRU VHFRQG DW WKH KRPH VFUHHQ WKH WLPHU LV UHVHW 6ZLWFKHV$WR+FDQEHVHOHFWHGDVWKHUHVHWVZLWFK 566: 7KH212))GLUHFWLRQFDQDOVREHVHW Ĺ7KH XSGRZQ WLPHU DXGLEOH DODUP LQGLFDWHV WKH WLPHE\DEHHSHYHU\VHFRQGFRQWLQXRXVEHHSLQJ DW VHFRQG LQWHUYDOV IURP VHFRQGV EHIRUH WKH VHWWLPHDQGDFRQWLQXRXVEHHSLQJDWDVHFRQG LQWHUYDOIURPVHFRQGVEHIRUHWKHVHWWLPH Method Common function Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "TIMER" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź â Select the item with the Jog key. â When the throttle switch is TIMER Time set up Mode selection ON Switch selection Switch direction Reset Switch selection Switch direction ďźTimer1ďź ďźTimer2ďź selected at switch selection, hold the throttle stick in the position you want to set the ON/OFF point at ON direction setting and set the ON/OFF position by pressing the Jog key for 1 second. The timer is turned ON at points higher than this position. The ON direction can be switched by pressing the + key or â key. Timer ďźTMR1ďźďźTMR2ďź â Mode selection â Select timer mode from the "MODE" with the ďź or â key. ďź â or ďźRange ďź Defaultďź UP, DOWN, DN-STP/UP 48 â Timer time setting â Switch selection and ON direction setting ⥠Set the time by pressing the + key or â key at each TIME (minutes):(second) item. ⢠Select the switch by pressing the + key or â key at the ON-SW or RS-SW item and set the ON direction by pressing the + key or â key at the ON direction setting item. (Switch setting range/Default) ON-SW: SwA âź H, ST-THR, PWR-SW/SwA RS-SW: SwA âź H/SwA (Switch ON direction/Default) 3P SW: NULL (normally oďŹ), UP, UP&DWN, UP&CNT, CENTER, CNT&DN, DOWN/NULL 2P SW: NULL, UP, DOWN/NULL ďźRange ďź Defaultďź 0 âź 99 m i n u t e s 59 seconds/10 minutes 00 second Servo monitor ďź Servo test SERVO Function The servo display/servo test function displays the CH1 to CH10 servo output bar graph and tests servo operation. Ĺ7KHVHUYRGLVSOD\IXQFWLRQFDQEHXVHGIRUDVLPSOH RSHUDWLRQ FKHFN RI VXFK IXQFWLRQV DV WKH PL[LQJ IXQFWLRQ Ĺ:KHQWKHVHUYRWHVWIXQFWLRQLVWXUQHGRQWKHVHUYR PRYHV WR WKH OHIW DQG ULJKW DW WKH VHW SHULRG $ Method (Common) YDULDEOH VSHHG /15 OLQHDU PRGH RU Ă[HG VSHHG -03 MXPS PRGH FDQ EH VHOHFWHG 7KLV FDQ EH XVHGWRFKHFNWKHVHUYRHWF2SHUDWLRQ212)) FDQDOVREHVHOHFWHGIRUHDFKFKDQQHO CAUTION Using the servo test will move the servos to their full throw. Do not use this with linkages installed. Using it may damage the servo and linkage. Calling the setting screen ⥠Select "SERVO" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. 6(592ĺ˛ĺ˛12 7(67㣠Switching to the servo test screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź ďź1 secondďź â Select the setting item with the Jog key. (Servo Testďź Servo test ON/OFF Channel Select 6(592ĺ˛ĺ˛12 *53+㣠7<3(ăŁ/15 7(67ăŁ2)) &<&/㣠63'㣠âŤŮšâŹ$&7âŤŮ¸âŹ,1+ &+ăŁŮ âŤŮ¸ ٸ ٸ ٸ ٸ ٸ ٸ ٚ⏠â Switch the screen by selecting TEST and operating the jog key to the left and right. â The servo operating position of each channel is displayed on a bar graph. Common function (Servo Monitorďź Screen change â Where "GRPH" is chosen, a Jog key is pressed in right or left. Type Select Cycle Select Speed setting â Operation of a servo test Servo test â Type/cycle/speed setting â Channel selection â Servo test start/stop â Select the setting item (TYPE, CYCL, SPD) with the Jog key and set the item by pressing the + key or â key. ⥠Select the channel you want to test with the Jog key and select ACT/INH by pressing the + key or â key. ⢠Select the "TEST" item with the Jog key and start/stop the servo test by pressing the + key or â key. ďź â or ďź â or ďźRange ďź Defaultďź TYPEďźLNR, JMP ďź LNR CYCLďź1 âź 100 ďź 10ďźfull speed at 1ďź SPDďź1 âź 100 ďź 7ďźfull speed at 100ďź ďź â or Selection rangeďźACT, INH DefaultďźINH ďźonly CH1 is ACTďź Selection rangeďźON, OFF DefaultďźOFF 49 END POINT End point (Common) Function The End Point function adjusts the left and right servo throws, generates differential throws, and will correct improper linkage settings. Ĺ7KH VHUYR WUDYHO FDQ EH DGMXVWHG LQGLYLGXDOO\ DW WKHOHIWDQGULJKWVLGHV Servo throw At 100% setting the servo throw of each channel is about 40° for channels 1 to 4 and about 55° for channels 5 to 10. However, the maximum servo travel for channels 5 to 10 is about 110%. *When channels 5 to 8 were mixed by ďŹaperon, diďŹerential or ailvator, the throw becomes the same (about 40° ) as channels 1 to 4. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "END POINT" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź Common function END POINT â Select the channel with the Jog key. CH1 : AIL âŤÚ⏠âŤÚ⏠100 100 12 ⍠ÚâŹ1: 2: 3: 4: 5: AIL ELE THR RUD GER 100 100 100 100 100 /100 /100 /100 /100 /100 â The setting rate of each channel ďźLeft ďź Downďź ďźRight ďź Upďź rate display rate display ďź ChannelDisplay ďź ACROBATIC HELICOPTER GLIDER (AF4) MULTICOPTER 1: AIL ďźAileronďź 6: FLP ďźFlapďź1: AIL ďźAileronďź 6: PIT ďźPITCHďź1: AIL ďźAileronďź 6: FL2ďźFlap2ďź 1: AIL ďźAileronďź 6: AUX 2: ELE ďźElevatorďź7: AUX 2: ELEďźElevatorďź7: AUX 2: ELEďźElevatorďź7: AL2 ďźAileron2ďź2: ELEďźElevatorďź7: AUX 3: THR ďźThrottleďź8: AUX 3: THR ďźThrottleďź8: AUX 3: MOT ďźMotorďź 8: FL3ďźFlap3ďź 3: THR ďźThrottleďź8: AUX 4: RUD ďźRudderďź9: AUX 4: RUD ďźRudderďź9: AUX 4: RUD ďźRudderďź9: FL4 ďźFlap4ďź 4: RUD ďźRudderďź9: AUX 5: GER ďźGearďź 10: AUX 5: GYR ďźGYROďź 10: AUX 5: FLP ďźFlapďź 10: AUX 5: MOD 10: AUX End point â A channel is chosen by Jog key. Selection rangeďź1 âź 10ch ⥠Operate the stick or knob of the selected channel fully to the left (down) or right (up) and adjust the rate by pressing the + key or â key. ďź or â Rangeďź 0 âź 140% Defaultďź100% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the stick and VR by repeating step â . 50 TRIM Trim reset ďź Trim step (Common) Function Trim Reset Trim Step This function returns the trim of the model memory in use to the center (initial state). However, at this time, sub trim and trim step amount are not reset. Method The amount of trim change per step can be changed between 1 and 40 according to the aircraft capacity and trim application. Set it to match the application. With ordinary aircraft, a setting of about 2 to 10 should be fine. ,QLWLDOYDOXH Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "TRIM" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź Trim Reset Trim step â Select the item with the Jog key. Common function â The numbers in ( ) indicate the current trim position. (The trim operating range is 120 âź 100[DT5,DT6]ďź TRIM ďźTrim step rateďź Trim reset â Select the RESET item and press the Jog key for 1 second. ďź1 secondďź â For example, when the step size is the initial value (4), trim movement from center to end is 30 steps. If the step size is made 40, the trim moves 3 steps. â A "beep" sounds to indicate that resetting is complete. At this time, the trim position number returns to 0. Trim step â Select the trim you want to set from the STEP item and set the step size by pressing the + key or â key. ďź â or Rangeďź1 âź 40 Defaultďź4 â When you want to return the set value to the initial value, press the + key and â key simultaneously. 51 SUB TRIM Sub trim (Common) Function Setting precautions The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up. When you begin to set up a model, be sure that the digital trims are set to their center position. If sub trim is too large, the servo operating range may be exceeded at maximum control surface angle and generate a dead band in which the servo does not operate. First connect the linkage so that the amount of sub trim used is held to a minimum. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "SUB TRIM" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź Common function â Select the channel with the Jog key. SUB TRIM 12 CH1 : AIL ⍠ÚâŹ1: 2: 3: 4: 5: AIL ELE THR RUD GER â SUB trim rate of each channel. SUB trim rate of the selected channel. ďź ChannelDisplay ďź ACROBATIC HELICOPTER GLIDER (AF4) MULTICOPTER 1: AIL ďźAileronďź 6: FLP ďźFlapďź1: AIL ďźAileronďź 6: PIT ďźPITCHďź1: AIL ďźAileronďź 6: FL2ďźFlap2ďź 1: AIL ďźAileronďź 6: AUX 2: ELE ďźElevatorďź7: AUX 2: ELEďźElevatorďź7: AUX 2: ELEďźElevatorďź7: AL2 ďźAileron2ďź2: ELEďźElevatorďź7: AUX 3: THR ďźThrottleďź8: AUX 3: THR ďźThrottleďź8: AUX 3: MOT ďźMotorďź 8: FL3ďźFlap3ďź 3: THR ďźThrottleďź8: AUX 4: RUD ďźRudderďź9: AUX 4: RUD ďźRudderďź9: AUX 4: RUD ďźRudderďź9: FL4 ďźFlap4ďź 4: RUD ďźRudderďź9: AUX 5: GER ďźGearďź 10: AUX 5: GYR ďźGYROďź 10: AUX 5: FLPďźFlapďź 10: AUX 5: MOD 10: AUX Sub trim â A channel is chosen by Jog key. ⥠Select the SUB trim you want to set from channel item and set the rate by pressing the + key or â key. ďź Selection rangeďź (page 1) 1 âź 5ch (page 2) 6 âź 10ch 52 â or Rangeďź -120 âź +120% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. P.MIX1-6 Program mixing 1 âź 6 (Common) Function Mixing that can independently customize 6 functions can be used. Programmable mixing is used to remove bad tendencies of the aircraft and PDNH RSHUDWLRQ SOHDVDQW ,Q DGGLWLRQ WR PL[LQJ between arbitrary channels, this function includes linking (linking with another mix), trim addition, offset, and switch setting functions. P.MIX 1 âź 4 (normal type) The following functions can be set for programmable mixing 1 to 4: ăMixing Channelă â Use this function by changing the channel because the master channel and slave channels initial setting is a temporary combination. â When OFS was selected as the master channel, the mixing rate setting applies to slave only. When a mixing rate is set, slave servo operation is oďŹset by that amount. â A knob (VR) or digital trim (DT5, DT6), as well as a channel, can be selected as the master channel. ăTrim selectionă â Whether or not mixing includes master channel trim operation can be selected. â The master channel mixing reference point can be shifted. ăSwitch selectionă â The programmable mixing ON/OFF switch can be selected. The switches that can be selected are switches A to H and the throttle stick. â The switch operating direction can be set. When a 2 position switch was selected, up /down can be set, and when a 3 position switch was selected, up/up and down /up / and center/center/center and down /down can be selected. When the throttle stick was selected, the ON/OFF position and operation direction can be set. When "NULL" is selected, mixing is always ON. Common function ăMixing reference point changeă P. MIX 5 âź 6ďźcurve typeďź Programmable mix 5 to 6 allows setting of the mixing rate by 5 point curve. OFS and knob/digital trim use and trim selection by normal type master channel setting described above are impossible, but switch selection is possible. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "P.MIX1-6" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź 53 P.MIX Selection ďźP.MIX 1-6ďź â Calling the setting screen â Use the Jog key to select the P.MIX number you want to use. ⥠Call the setting screen by pressing the Jog key. to P.MIX1 âź 4 set up screen â P.MIX1 âź 4ďźnormal typeďź â P.MIX5 âź 6ďźcurve typeďź to P.MIX5 âź 6 set up screen ďźP.MIX1 âź 4 set up screenďź Function activation Mixing rate adjustment â When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. OďŹset Master CH selection Slave CH selection â Select the item with the Jog key. ďźMaster CH Current positionďź Trim ON/OFF Switch selection Switch direction Common function P.MIX1 âź 4 â Function activation â Master/slave channel selection â Select the MIX item and select ON or OFF by pressing the + key or â key. ⥠Select the MASTR channel you want to use by pressing the + key or â key. ďź â or â When you do not want to use the function select INH. â or ⢠Select the Slave channel you want to us by pressing the + key or â key. â A knob VR or digital trim DT5/DT6, as well as channels 1 to 10, can be speciďŹed as the master channel. In addition, when OFS was selected as the master channel, slave servo operation is oďŹset. â Mixing rate adjustment ⣠Select the RATE item and adjust the mixing rate by pressing the + key or â key for each direction of the stick, etc. selected at the master channel. ďź ďź â or Rangeďź-100 âź +100% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. ďźChanging the ON/OFF Switchďź â ON/OFF Switch selection â Switch ON direction setting â Select the "SW" item and then select the switch by pressing the + key or â key. ⥠Select the "POSI" item and select the switch ON direction by pressing the + key or â key. ďź â or Selection rangeďźSwA âź SwHăTHR 54 ďź â or â 2P SWďźNULL ďźalways ONďź , UP, DOWN â 3P SWďźNULLďźalways ONďź, UP, UP&D, UP&C, CNTR, C&DN, DOWN â THR stick: Hold the stick at the ON/OFF point and set the ON/OFF position by pressing the Jog ďź1 secondďź key for 1 second. (If the Jog key is pressed for 1 second when the position was set, it returns to the NULL state.) The switch ON direction can also be selected by pressing the + key or â key. ďźChanging the mixing reference pointďź ďźIncluding trim operationďź â Mixing reference point setting â Trim ON/OFF setting â Select the "OFFST" item and hold the master side stick or knob in the position you want to set and set the new reference point by pressing the Jog key. ďź1 secondďź ďź â or RangeďźOFFăON Rangeďź-100 âź +100% ďźTHR only 0 âź 100%ďź Defaultďź0% â Select the "TRM" item and select ON or OFF by pressing the + key or â key. DefaultďźOFF â When you do not want to include trim in mixing select OFF. CAUTION At the end of setting, check that the mixing function is performed normally. ďźP.MIX5 âź 6 set up screenďź â Select the item with the Jog key. Function activation Master CH select Slave CH select â When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. Switch selection Switch ON direction Common function â The set curve is displayed on a graph. 5Point curve setting P.MIX5 âź 6 Refer to the P.MIX1 âź 4 setting method described previously for settings other than the 5 point curve setting described below. â 5point curve setting â Select the setting item (P-1 âź P-5) of each point with the Jog key and set the amount of movement of each point by pressing the + key or â key. ďź â or Rangeďź-100 âź +100% Defaultďź0% CAUTION At the end of setting, check that the mixing function is performed normally. 55 AUX-CHAN AUX Channel (Common) Function Auxiliary channel function (AUX-CH): defines the relationship between the transmitter controls and the receiver output for channels 5-10. Remember that if you assign primary control of a channel to a switch which you later use for other functions (like dual/triple rates or airbrakes), every time you use that other function you will also be moving the auxiliary channel. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "AUX-CHAN" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź Common function AUX-CHAN &+ăŁSwG &+ăŁ95 &+ăŁ'7 &+ăŁ'7 &+ăŁ6Z$ &+ăŁ6Z' ďź AUX Channel Default ďź CH5 CH6 CH7 CH8 CH9 CH10 ACROBATIC SwGďźSwitchGďź VRďźVolumeďź DT5ďźTrim5ďź DT6ďźTrim6ďź SwA(SwitchA) SwD(SwitchD) CH5 CH6 CH7 CH8 CH9 CH10 HELICOPTER SwFďźSwitchFďź ---ďźPITCHďź SwCďźSwitchCďź VRďźVolumeďź SwA(SwitchA) SwD(SwitchD) CH5 CH6 CH7 CH8 CH9 CH10 GLIDER SwGďźSwitchGďź VR ďźVolumeďź DT5 ďźTrim5ďź DT6 ďźTrim6ďź SwA(SwitchA) SwD(SwitchD) CH5 CH6 CH7 CH8 CH9 CH10 AUX Channel â A channel is chosen by Jog key. ⥠Select the "SW" item and then select the switch by pressing the + key or â key. ďź Selection rangeďź5 âź 10ch â or Selection rangeďźNULL, SwA âź SwH, VR, DT5, DT6 56 MULTICOPTER SwEďźSwitchEďź SwC ďźSwitchCďź VR ďźVolumeďź DT6 ďźTrim6ďź SwA(SwitchA) SwD(SwitchD) WARNING The priority of AUX Don't assign two or more functions to one channel. Priority may be given to a higher rank function and a low rank function may be canceled. higher rank GYRO CH5 PITCH CH6 FLAP TRIM CH7 AIL DIFF ACRO Priority SW-G FLAPERON GYRO CH8 AILVATOR PITCH low rank VR DT5 THR â NEEDLE GYRO DT6 CH9 SW-A CH10 SW-D CH5 GYRO SW-F CH6 PITCH CH8 ELE2 THR â NEEDLE GYRO SW-C GOVERNOR SW-A CH9 GOVERNOR CH10 SW-D GLIDER CH5 FLAP1 CH6 FLAP2 CH7 AILERON2 GYRO SW-D CH8 FLAP3 GYRO DT6 CH9 FLAP4 CH10 CAMBR MIX CH5 GYRO GYRO DT5 SW-G VR Common function GOVERNOR CH7 GYRO HELI SW-A VR SW-E CH6 SW-C MULTICOPTER CH7 GYRO VR CH8 GYRO DT6 CH9 SW-A CH10 SW-D 57 Parameter function (Common) PARAMETER submenu: sets those parameters you would likely set once, and then not disturb again. Once you have selected the correct model you wish to work with, the next step is setting up the SURSHUSDUDPHWHUVIRUWKLVVSHFLÂżFPRGHO PARAMETER Function Data resetďźRESETďź The present model data is reset. Data Reset does NOT reset, ATL Trim, TELEMETRY mode, or STK POSI Alarm. Model typeďźTYPEďź SWASH : Only helicopter WING : Only glider MODEL TYPE: sets the type of programming used for this model. The T10J has 30 model memories, which can each support: â One powered aircraft (ACRO) memory type (with multiple wing and tail conďŹgurations. See twin aileron servos, twin elevator servos, ELEVON, and V-TAIL for further information.) â Eight helicopter swashplate types, including CCPM. See Helicopter MODEL TYPE for details. â If you use CGY750, the swash type should choose H-1. ( Swash type is chosen by setup in CGY750. ďź â Five glider wing types. See glider WING TYPE for details. â Multicopter type. Common function Before doing anything else to set up your aircraft, ďŹrst you must decide which MODEL TYPE best ďŹts this particular aircraft. (Each model memory may be set to a diďŹerent model type.) If your transmitter is a T10JA, the default is ACRO. If it is a T10JH, the default is HELI(H1). ATL TrimďźATLďź Adjustable travel limit (ATL): makes the channel 3 TRIM LEVER (THROTTLE TRIM) eďŹective only at low throttle, disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to ON. If you are not using channel 3 for throttle, you may want trim operation the same as on all other channels. To do so, set ATL to OFF. If you need the ATL to be eďŹective at the top of the stick instead of the bottom, reverse the THR-REV setting. Note that this aďŹects all models in the radio, not just the model you are currently editing. LCD contrastďźCONTRASTďź Contrast adjustment LCD screen. â You adjust to legible contrast. set up range -10 âź +10 Back lightďźBACK-LITďź Back light mode of a LCD screen can be chosen. â ALWAYS / KEY-ON (Shines for a deďŹnite period of time after key operation.) / OFF Light timeďźLIT-TIMEďź Sets the length of time the backlight will stay on. â Set up range 1 âź 30 Light adjustmentďźLIT-ADJSďź Light volume adjustment of a back light. â Set up range 1 âź 30 Home displayďźHOME-DSPďź Item selection displayed on a home screen â Futaba logo (Default), USR-NAME , RX BATT, DT5/DT6, THR/PIT (Case of helicopter, the position of a throttle and pitch.) 58 Battery alarmďźBATT-ALMďź Select the battery alarm voltage according to the battery to be used. â 4 dry cell batteries â 4.2V DRY4 â HT5F1800B (NiMH battery) â 5.0V NiMH5 â FT2F2100B (Lithium ferrite battery) â 5.8V LiFe2 Battery alarm vibrationďźBATT VIBďź Battery alarm is told with vibration. Buzzer toneďźBUZ-TONEďź The tone of buzzer sound when a key is pressed. â Set up range : OFF,1(low) âź 100(high) Jog key navigationďźJog-NAVIďź Blink at the time of Jog key operation, Display of the operation direction. Jog lightďźJog-LITďź ON/OFF of a Jog key light. Jog light timeďźJog-TIMEďź Time setting in which a Jog key light shines. â Set up range : 1 âź 30(s) Telemetry mode settingďźTELEMETRY MODEďź â RangeďźACT / INH Telemetry display units settingďźTELEMETRY UNITďź Sets whether the telemetry display is in meters or yards/pounds. â RangeďźMETER / YARD ďźâ / âďź Speech language settingďźSPEECH LANGUAGEďź Sets the speech language when listening to telemetry information through earphones. â RangeďźJapanese (JPN), English (English), German (Deutsch) Common function Sets whether or not telemetry is activated. When using 2 receivers with 1 transmitter, select INH. Speech volume settingďźSPEECH VOLUMEďź Sets the volume when listening to telemetry information through earphones. â RangeďźLOW / HIGH Stick position alarm settingďźSTK POSI ALRMďź Can be set so that an audible alarm sounds once when the throttle stick reaches the set position. 59 Method Calling the setting screen ⥠Select "PARAMETER" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ďź â˘ Open the setting screen by pressing the Jog key. ďź1 secondďź PARAMETER Data reset Model type 12345 5(6(7ăŁExecute 7<3(ăŁ$&52%$7,& Swash type (In the case of a helicopter ) Wing type (In the case of a glider ) ATLTrim page 1 $7/ăŁ21 0'/ â Next page 2 âź 5 Common function LCD contrastďźCONTRASTďź Back lightďźBACK-LITďź Light timeďźLIT-TIMEďź Light adjustmentďźLIT-ADJSďź Home displayďźHOME-DSPďź Battery alarmďźBATT ALMďź Battery alarm vibrationďźBATT VIBďź Buzzer toneďźBUZ-TONEďź Jog key navigationďźJOG-NAVIďź Jog lightďźJOG-LITďź Jog light timeďźJOG-TIMEďź ďźTELEMETRY MODEďź ďźTELEMETRY UNITďź ďźSPEECH LANGUAGEďź ďźSPEECH VOLUMEďź Stick position alarmďźSTK POSI ALRMďź page 2 page 3 page 4 page 5 Date reset â Call the "RESET" from the PARAMETER by Press the Jog key for 1 second. ⥠Date reset by pressing the Jog key. ďź1 secondďź â ConďŹrmation message "sure?" blinks. â A confirmation "beep" sounds and "COMPLETE" is displayed on the screen is complete. For safety, a double setting system is used. You need to conďŹrm your setting changes by pressing the jog key. When "COMPLETE" can be seen, it is the completion of reset. CAUTION 60 Only the throttle channel (CH3) initial setting is REV (reverse). Thoroughly check the Hi and Low directions of the engine or motor used and be careful that they do not suddenly run at full speed. Even after data reset, CH3 is reversed. Model type â Select the "TYPE" item and then select the model type by pressing the + key or â key. ďź âĄ Press the Jog key for 1 second. ⢠Model type change by pressing the Jog key. ďź1 secondďź â or â Confirmation message "sure?" blinks. â The new model type is displayed on the screen. For safety, a double setting system is used. You need to conďŹrm your setting changes by pressing the jog key. If you fail to press the jog key and see "COMPLETE" on your screen, your changed are not saved. â A confirmation "beep" sounds is complete. Selection rangeďź ACROBATIC, HELICOPTER,GLIDER,MULTI COPT Swash typeďźfor Heliďź â Select the "SWASH" item and then select the swash type by pressing the + key or â key. â ďź1 secondďź â C o n f i r m a t i on messag e "sure?" blinks. or ⢠Swash type change by pressing the Jog key. For safety, a double setting system is used. You need to conďŹrm your setting changes by pressing the jog key. If you fail to press the jog key and see "COMPLETE" on your screen, your changed are not saved. â A confirmation "beep" sounds is complete. Selection rangeďźH-1, HR3, H-3, HE3, HN3, H-2, H-4, H4X Wing typeďźfor Gliderďź â Select the "WING" item and then select the swash type by pressing the + key or â key. ďź â ⥠Press the Jog key for 1 second. ⢠Swash type change by pressing the Jog key. ďź1 secondďź â C o n f i r m a t i on messag e "sure?" blinks. or Common function ďź âĄ Press the Jog key for 1 second. For safety, a double setting system is used. When a change is cancelled after the conďŹrmation message is displayed, the change is not made when moved to another setting item by Jog key. â A confirmation "beep" sounds is complete. Selection rangeďź1AIL, 2AIL, 2A+1F, 2A+2F, 2A+4F ATL Trim ON/OFF â Select the "ATL" item and change the mode by pressing the + key or â key. ďź â or Selection rangeďźON, OFF DefaultďźOFF 61 LCD contrast â Select the "CONTRAST" item and change numerical value (contrast) by pressing the + key or â key. ďź Selection rangeďź-10 âź +10 â or Defaultďź0 Back-light ďź Light-time ďź Light-adjustment â Back-light mode â Light-time Select the "BACK-LIT" item and change the mode by pressing the + key or â key. ďź â â Light-adjustment Select the "LIT-TIME" item and change numerical value (time) by pressing the + key or â key. ďź or â Select the "LIT-ADJ" item and change numerical value (brightness) by pressing the + key or â key. ďź or â or Common function â "ALWAYS"ďźalways ON "OFF"ďźalways OFF "KEY-ON"ďźIt light on after Key operation. â It is only a case in "KEY-ON" mode here. Selection rangeďź ALWAYS, OFF, KEY-ON Selection rangeďź1 âź 30(s) Defaultďź10(s) Selection rangeďź1 âź 30 Defaultďź15 DefaultďźALWAYS â When you want to return the set value to the initial value, press the + key and â key simultaneously. â When you want to return the set value to the initial value, press the + key and â key simultaneously. â It is the brightest at 30. Home display â Select the "HOME-DSP" item and change the mode by pressing the + key or â key. ďź â â "Futaba"ďźDisplay about a Futaba logo. "USR-NAME"ďźDisplay about a user name. "DT5/DT6"ďźDisplay about the position of DT5 and DT6 "RX BATT"ďźDisplay about the receiver battery voltage "THR/PIT"ďźDisplay about the position of pitch and throttle. Selection rangeďź Futaba, USR-NAME,DT5/ DT6, RX BATT, THR/PIT(*) DefaultďźFutaba *Only Heli mode can be chosen about THR/PIT. Battery alarm voltage â Select the "BATT ALM" item and change the numerical value (voltage) by pressing the + key or â key. ďź â or â AA alkaline batterys â 4.2V DRY4 â Futaba HT5F1800B â 5.0V NiMH5 â Futaba FT2F2100B â 5.8V LiFe2 62 Selection rangeďź 4.2V 4.6V 5.0V 5.4V 5.8V 6.2V 6.6V 7.0V 7.4V *The voltage drop of a rechargeable battery and a dry cell battery is different. When using a rechargeable battery, always change the voltage. Battery alarm voltage vibration â Select the "BATT VIB" item and change the ON or OFF by pressing the + key or â key. ďź â or Selection rangeďź ON, OFF â ON â The battery alarm of a transmitter is told with vibration. Buzzer tone â Select the "BUZ-TONE" item and change the numerical value (tone) by pressing the + key or â key. The higher the numerical value the higher the tone. ďź or â Selection rangeďź OFF, 1 âź 100 â When you want to return the set value to the initial value, press the + key and â key simultaneously. â Select the "Jog-NAVI" item and change the mode by pressing the + key or â key. ďź â or Selection rangeďź ON,OFF Common function Jog key navigation When NAVI selected ďŹashes when the Jog key was pressed. When a function that only operates in the vertical direction is selected, the LED blinks vertically. When a function that operates in the vertical and horizontal directions is selected, the LED blinks vertically and horizontally. Jog light â Select the "Jog-LIT" item and change the mode by pressing the + key or â key. ďź â or â "ALWAYS"ďźThe light is always switched on. "KEY-ON"ďźKEY operation â Light on. "OFF"ďźAlways oďŹ. Selection rangeďź ALWAYS, KEY-ON, OFF DefaultďźKEY-ON 63 Jog light time â Select the "Jog-TIME" item and change numerical value (time) by pressing the + key or â key. ďź â or Selection rangeďź 1 âź 30 Defaultďź10 â Jog-Lit sets the lighting time when KEY-ON was set. â When you want to return the set value to the initial value, press the + key and â key simultaneously. Telemetry mode â Select the "TELEMETRY-MODE" item and change the mode by pressing the + key or â key. ďź â or Selection rangeďź ACT, INH Common function Telemetry unit â Select the "TELEMETRY-UNIT" item and change the mode by pressing the + key or â key. ďź or â Selection rangeďź METER, YARD Speech language â Select the "SPEECH-LANGUAGE" item and change the language by pressing the + key or â key. ďź â or Selection rangeďź Japanese, English, Deutsch Speech volume â Select the "SPEECH-VOLUME" item and change the volume by pressing the + key or â key. ďź â or 64 Selection rangeďź HIGH, LOW Stick position alarm An alarm (single beep) can be sounded at the speciďŹed throttle stick position. â Alarm function ON/OFF can be set by switch. Beep sounds When the THR stick is set to the speciďŹed position. Select "Parameter" Press the Jog key to the side and select page 5. â Select the item with the Jog key. â Stick position is chosen by Jog key. 3$5$0(7(5ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛5 67.326,$/50 0'/ 02'(ăŁ21 6:ăŁ6Z$ 326,ăŁ'2:1 67,&.㣠⥠Set the throttle stick to the position at which you want to generate the alarm. ParameterVHWWLQJLVQRW UHVHW +RZHYHU STK POSI ALRM, Telemetry mode DQG WKH ATL trim RQ ZKLFK (MDL) Z D V G L V S O D \ H G D U H UHVHWWDEOH â When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. âThe number in parenthesis is the current throttle stick position. ⢠When the Jog key is held down the alarm sounds at that position. Common function INH â ON/OFF Switch selsction Switch direction Stick position ďźSTK POSI ALRM ďź â 3$5$0(7(5ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛ĺ˛5 67.326,$/50 0'/ 02'(ăŁ21 6:ăŁ6Z$ 326,ăŁ'2:1 67,&.㣠Memorize the position at which the beep is to sound. THR Stick 65 TELEMETRY Telemetry (Common) Function This screen displays and sets the various information from the receiver. An alarm and vibration can be generated depending on the information. For example, a drop in the voltage of the receiver battery housed in the aircraft can be reported by an alarm. â This function can only be used in the T-FHSS Air mode. The S-FHSS system cannot use telemetry. â Telemetry sensors sold separately can be mounted in the aircraft to display a variety of information. (Receiver voltage does not require a sensor.) â The telemetry function cannot be used if the telemetry mode of the parameters is not ACT. â When 2 receivers are used with 1 transmitter, the telemetry function cannot be used. Common function Viewing the receiver voltage. Setting is unnecessary. When menu telemetry is listened to, the voltage appears. P.66 Viewing the drive battery voltage. CA-RVIN-700 and wiring work are necessary. P.70 Using various optional telemetry sensors. Optional telemetry sensors are necessary. T10J setting is unnecessary. Using several telemetry sensors of the same type. Setting by "sensor" in the menu is necessary. (Slot setting is necessary.) Setting alarms from the telemetry information. Setting by "Telemetry" in the menu is necessary. P.74 âź 82 P.84 P.75 âź 82 RX-BATT â Viewing the receiver voltage. In the initial state, the receiver voltage is displayed at the transmitter. Display Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "TELEMETRY" from the menu with the Jog key. ďź1 secondďź Receiver voltage display TELEMETRY RX-BATT -----RECEIVER EXT-VOLT -----RECEIVER 66 ⢠Open the setting screen by pressing the Jog key. â How to display receiver voltage on a home screen. PARAMETER HOME-DSP "RX BATT" is chosen by ďź key or â key. â Viewing the receiver voltage maximum and minimum values. In the initial state, the receiver voltage maximum and minimum values are displayed in the transmitter. (Value until reset) Display Calling the setting screen â Select "RX-BATT" from the telemetry screen with the Jog key. ⥠Open the setting screen by pressing the Jog key. Receiver voltage display Receiver voltage MIN Receiver voltage MAX RX-BATT MIN/MAX= 9 99 63((&+ăŁ,1+6:ăŁ18// MIN/MAX reset â Select "MIN/MAX" from the RX-BATT screen with the Jog key. ⥠Date reset by pressing the Jog key for 1 second. Common function (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 â A confirmation "beep" sounds when complete. Ĺ 5HFHLYHU â 7UDQVPLWWHU 7 K H U H F H S W L R Q R I W K H VLJQDOIURPWKHUHFHLYHUWR WKH WUDQVPLWWHU LV VKRZQ 7KLVGRHVQRWDIIHFWĂLJKW WARNING 'RQRWVWDUHDWRUVHWWKHWUDQVPLWWHUVHWWLQJVFUHHQZKLOHĂ\LQJ Ĺś/RVLQJVLJKWRIWKHDLUFUDIWGXULQJĂLJKWLVYHU\GDQJHURXV Ĺś:KHQ\RXZDQWWRFKHFNWKHLQIRUPDWLRQGXULQJĂLJKWFDOOWKHWHOHPHWU\VFUHHQEHIRUHĂLJKWDQGKDYHWKHVFUHHQ FKHFNHGE\VRPHRQHRWKHUWKDQWKHRSHUDWRU 67 â Setting receiver voltage alarm. Use this setting to sound an alarm when the receiver battery voltage drops dangerously low. VIB (vibration) that vibrates the transmitter at the same time can also be set. Method Calling the setting screen â Select "RX-BATT" from the telemetry screen with the Jog key. ⥠Open the setting screen by pressing the Jog key. RX-BATT 9 99 MIN/MAX= Common function DN (down) shows than an alarm is generated when the voltage drops below the set voltage. (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 63((&+ăŁ,1+6:ăŁ18// Alarm set â In the RX-BATT screen state, select (ALARM) from the menu with the Jog key. ⥠Select the "ACT" by pressing the + key or â key. ďź or â Vibration set â In the RX-BATT screen state, select (VIB) from the menu with the Jog key. ⥠Select the "TYP1 âź TYP3" by pressing the + key or â key. "VIB" types TYP 1 ďź or â TYP 2 TYP 3 Alarm voltage set â In the RX-BATT screen state, select (LIMIT) 0.0V from the menu with the Jog key. ⥠Select the voltage by pressing the + key or â key. Selection rangeďź 3.5V âź 8.4V ďź or â â When you want to set 5.0V, press the + key and â key simultaneously. 68 â Listening to the receiver voltage by speech. The receiver voltage can be heard verbally from the transmitter with a commercial earphone (3.5Ď plug). The speech function can be turned on and oďŹ with the speciďŹed switch. Method Calling the setting screen â Select "RX-BATT" from the telemetry screen with the Jog key. ⥠Open the setting screen by pressing the Jog key. RX-BATT 9 99 MIN/MAX= (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 Selects the switch that turns the speech function on and oďŹ. 63((&+ăŁ,1+6:ăŁ18// Speech â In the RX-BATT screen state, select (SPEECH) from the menu with the Jog key. ⥠Select the "ACT" by pressing the + key or â key. ďź or â Common function Speech ACT / INH Switch â In the RX-BATT screen state, select (SW) from the menu with the Jog key. ⥠Select the switch by pressing the + key or â key. ďź or Selection rangeďź NULL, SWA âź SWH â OFF In "NULL", a speech always turns on. OFF OFF ON 2 Position ON 3 Position 69 EXT-VOLT When connected as shown in the ďŹgure, the voltage of the drive battery in the aircraft and another power supply battery can be displayed at the T10J. â CA-RVIN-700 (external voltage input connector sold separately) is necessary. â Soldered wiring work is necessary. Extra Voltage Port R3008SB Fuse Black line CA-RVIN-700 Red line with external power input must be less than 70V Common function Power Battery or another power supply for servos Branch To Motor Controller or Servo â EXT-Voltage display When connected as shown in the ďŹgure, the drive battery voltage is displayed at the transmitter. Display Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "TELEMETRY" from the menu with the Jog key. ďź1 secondďź TELEMETRY RX-BATT -----RECEIVER EXT-Voltage display 70 EXT-VOLT -----RECEIVER ⢠Open the setting screen by pressing the Jog key. â EXT-Voltage MIN/MAX In the initial state, the EXT-voltage maximum and minimum values are displayed at the transmitter. (Value until reset) Calling the setting screen â S e l e c t "EX T- V OLT " f r o m t h e telemetry screen with the Jog key. ⥠Open the setting screen by pressing the Jog key. EXT-Voltage display EXT-Voltage MAX EXT-Voltage MIN EXT-VOLT MIN/MAX= 9 99 (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 MIN/MAX reset â In the EXT-VOLT screen state, select (MIN/MAX) from the menu with the Jog key. ⥠Date reset by pressing the Jog key for 1 second. Common function 63((&+ăŁ,1+6:ăŁ18// â A confirmation "beep" sounds is complete. 71 â EXT-Voltage alarm set up This setting will sound an alarm when the EXT-voltage drops dangerously low. VIB (vibration) that vibrates the transmitter at the same time can also be set. Method Calling the setting screen â Select "EXT-VOLT" from the telemetry screen with the Jog key. ⥠Open the setting screen by pressing the Jog key. EXT-VOLT 9 99 MIN/MAX= Common function DN (down) shows than an alarm is generated when the voltage drops below the set voltage. (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 63((&+ăŁ,1+6:ăŁ18// Alarm set â In the EXT-VOLT screen state, select (ALARM) from the menu with the Jog key. ⥠Select the "ACT" by pressing the + key or â key. ďź or â Vibration set â In the EXT-VOLT screen state, select (VIB) from the menu with the Jog key. ⥠Select the "TYP1 âź TYP3" by pressing the + key or â key. ďź or â "VIB" types If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3 Alarm voltage set â In the EXT-VOLT screen state, select (LIMIT) from the menu with the Jog key. ⥠Select the voltage by pressing the + key or â key. Selection rangeďź 0.0V âź 70.0V ďź or â â When you want to set 5.0V, press the + key and â key simultaneously. 72 â Listening to the EXT-voltage by speech. The EXT- voltage can be heard verbally from the transmitter with a commercial earphone (3.5mm plug). The speech function can be turned on and oďŹ with the speciďŹed switch. Method Calling the setting screen â Select "EXT-VOLT" from the telemetry screen with the Jog key. ⥠Open the setting screen by pressing the Jog key. EXT-VOLT 9 99 MIN/MAX= (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 63((&+ăŁ,1+6:ăŁ18// Speech ON/OFF Switch selection Speech â In the EXT-VOLT screen state, select (SPEECH) from the menu with the Jog key. ⥠Select the "ACT" by pressing the + key or â key. ďź or â Common function Speech ACT / INH Switch set â In the EXT-VOLT screen state, select (SW) from the menu with the Jog key. ⥠Select the switch by pressing the + key or â key. ďź or Selection rangeďź NULL, SWA âź SWH â OFF In "NULL", a speech always turns on. OFF OFF ON 2 Position ON 3 Position 73 Various telemetry sensors (optional) information display and alarm setting Various telemetry sensors (sold separately) are connectable to the S.BUS2 port of the R3008SB through a 3-way hub and relay terminals. The information of sensors connected at initialization can be viewed as long as 2 or more of the same kind of sensor are not used (for example, 2 temperature sensors). â Sensors that can be used with the T10J: Futaba SBS-01T, SBS-01RM, SBS-01RO, SBS-01A, SBS-01V, SBS-01G â Robbe sensors that can be used with the T10J: Robbe TEMP125, GPS-1675, VARIO-1712, VARIO-1672, CURR-1678 *Futaba does not sell Robbe sensor. Sensor Connection TEMP Sensor SBS-01T HUB 530âŤŮâŹPDJQHWâŤŮâŹ6HQVRU SBS-01RM S.BUS2 Connector 530âŤŮâŹRSWLFVâŤŮâŹ6HQVRU SBS-01RO HUB Altitude Sensor SBS-01A Common function Voltage Sensor SBS-01V HUB Method GPS Sensor SBS-01G *Refer to the manual of each sensor for the mounting instruction to the model of sensor. Sensor information can be viewed by calling telemetry from the menu and calling the connected sensor display page. The detailed setting screen of that sensor can be called by selecting and pressing the sensor you want to select with the Jog key. â Refer to the receiver battery (RX-BATT) item for a description of key operation. â Select "TELEMETRY" from the menu with the Jog key. TELEMETRY 1 2 3 RX-BATT 02 TEMP ----------RECEIVER SBS-01T EXT-VOLT -----RECEIVER ⥠The sensor item of your choice is chosen by Jog key, and Jog key is pressed. 05 R.P.M 0rpm SBS-01RM/O TELEMETRY 1 2 3 RX-BATT 02 TEMP ----------RECEIVER SBS-01T EXT-VOLT -----RECEIVER 05 R.P.M 0rpm SBS-01RM/O Sensor set up 74 TEMP : Display of SBS-01T(Option), and alarm setup *A temperature sensor must be installed in the aircraft. â Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER". TEMP is a screen which displays/sets up the temperature information from an optional temperature sensor. The temperature of the model (engine, motor, EDWWHU\HWF ZKLFKLVĂ\LQJFDQEHGLVSOD\HG ,ILWEHFRPHVKLJKHURUORZHUWKDQWKHVHWWLQJDQ alarm and/or vibration will alert you. Ĺ'1ZLOOVKRZWKDWDQ DODUP ZLOO VWDUW ZKHQ W K H W H P S H U D W X U H GURSV EHORZ WKH VHW YDOXH TYPE 1 63((&+ăŁ,1+6:ăŁ18// TYPE 2 TYPE 3 Ĺ6ZLWFKVHOHFWLRQ Ĺ < R X F D Q K H D U W K H WHPSHUDWXUH WKURXJK DQ HDUSKRQHRUKHDGVHWE\ DFWLYDWLQJ WKH 6SHHFK IXQFWLRQ OFF OFF OFF ON ON 2 Position Common function Ĺ6HOHFW>7(03@LQWKH7(/(0(75<VFUHHQDQGDFFHVV WKH VHWXS VFUHHQ VKRZQ EHORZ E\ SUHVV WKH -RJ Ĺ7KHPD[LPXPDQGWKHPLQLPXP NH\ Ĺ7HPSHUDWXUH ZKHQSRZHULQJ21DUHVKRZQ Ĺ0D[LPXPDQGPLQLPXPdate reset TEMP Ĺ 83ZLOO VKRZ WKDW DQ by pressing the Jog key for 1 second. ŮŚ DODUP ZLOO VWDUW ZKHQ 0,10$; ŮŚŮŚ WKHWHPSHUDWXUHULVHV "VIB" type (ALARM) (VIB) (LIMIT) DERYHWKHVHWYDOXH If the following types are selected, the 83ăŁ,1+ăŁ2))ăŁĺ˛ŮŚ transmitter will vibrate during the warning. '1ăŁ,1+ăŁ2))ăŁŮŚ 3 Position Alert set : Hot warning $OHUWVHW/RZWHPSHUDWXUHZDUQLQJ 0RYHWKHFXUVRUWRWKH83 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXHâ $GMXVWPHQWUDQJHâ aâ 83 /,0,7 â§'1 /,0,7 0RYHWKHFXUVRUWRWKH'1 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH'1 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXHâ $GMXVWPHQWUDQJHâ aâ 83 /,0,7 â§'1 /,0,7 *When the + - key simultaneous press, the rate is reset to the initial value. *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 75 R.P.M : Display of SBS-01RM/RO(Option), and alarm setup *A RPM sensor must be installed in the aircraft. RPM is a screen which displays / sets up the RPM information from an optional RPM sensor. The RPM of the model (engine, motor, etc.) ZKLFKLVĂ\LQJFDQEHVKRZQ ,ILWEHFRPHVKLJKHURUORZHUWKDQWKHVHWWLQJDQ alarm and/or vibration will alert you. Ĺ6HOHFW>530@LQWKH7(/(0(75<VFUHHQ DQGDFFHVVWKHVHWXSVFUHHQVKRZQ EHORZE\SUHVVWKH-RJNH\ Ĺ 7 K H P D [ L P X P Z K H Q SRZHULQJ21DUHVKRZQ Ĺ 0 D [ L P X P dat e r e s e t b y Ĺ530 pressing the Jog key for 1 second. R.P.M Ĺ83 ,QGLFDWHV WKDW WKH DODUP ZLOO VWDUW ZKHQ WKH 530 ULVHV DERYH WKHVHWYDOXH Common function Ĺ'1,QGLFDWHVWKDWWKH DODUP ZLOO VWDUW ZKHQ WKH 530 IDOOV EHORZ WKHVHWYDOXH USP MAX= USP (ALARM) (VIB) (LIMIT) 83ăŁ,1+ăŁ2))㣠'1ăŁ,1+ăŁ2))㣠7<3(ăŁ237),1㣠63((&+ăŁ,1+6:ăŁ18// Ĺ < R X F D Q K H D U W K H 530 GDWD WKURXJK DQ HDUSKRQH RU KHDGVHW E\$FWLYDWLQJWKH6SHHFK IXQFWLRQ "VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3 Ĺ0$* 0$*1(7,& RU237 237,&$/ LVVHWDFFRUGLQJ WRWKHVHQVRU\RXXVH Ĺ,Q 237,&$/ WKH QXPEHU RI EODGHV ),1 RIWKHSURSHOOHU UR WRU \RXUPRGHOLVHQWHUHG 6%6500$*1(7,& 6%652237,&$/ Ĺ,Q 0$*1(7,& WKH JHDU UDWLR RI \RXU HQJLQH PRWRU \RX DUH XVLQJLVHQWHUHG Ĺ6ZLWFKVHOHFWLRQ OFF OFF OFF ON 2 Position 76 ON 3 Position $OHUWVHW2YHUURWDWLRQV Alert set : Under rotations 0RYHWKHFXUVRUWRWKH83$/(57LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXHUSP $GMXVWPHQWUDQJHUSPaUSP 83 /,0,7 â§'1 /,0,7 0RYHWKHFXUVRUWRWKH'1$/(57LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXHUSP $GMXVWPHQWUDQJHUSPaUSP 83 /,0,7 â§'1 /,0,7 *When the + - key simultaneous press, the rate is reset to the initial value. *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ ALTITUDE : Display of SBS-01A / SBS-01G(Option), and alarm setup *An altitude sensor or GPS sensor must be installed in the aircraft. $/7,78'(LVDVFUHHQZKLFKGLVSOD\VVHWVXS the altitude information from an optional altitude sensor or GPS sensor. The altitude of the model ZKLFKLVĂ\LQJFDQEHNQRZQ,ILWEHFRPHVKLJKHU (low) than preset altitude, you can be told by alarm. To show warning by vibration can also be chosen. Data when a power supply is turned on shall be 0 m, and it displays the altitude which changed from there. Even if the altitude of an airfield is high, that shall be 0 m and the altitude difference from DQDLUÂżHOGLVGLVSOD\HG7KLVVHQVRUFDOFXODWHVWKH altitude from atmospheric pressure. Atmospheric pressure will get lower as you go up in altitude, using this the sensor will estimate the altitude. Please understand that an exact advanced display cannot be performed if atmospheric pressure changes in a weather situation. â Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER". Ĺ7KH PD[LPXP DQG WKH PLQLPXP ZKHQSRZHULQJ21DUHVKRZQ Ĺ 0D[LPXP DQG PLQLPXP GDWH UHVHW E\SUHVVLQJWKHJog keyIRUVHFRQG Ĺ6HOHFW >$/7,78'(@ LQ WKH 7(/(0(75< VFUHHQ DQG DFFHVV WKHVHWXSVFUHHQVKRZQEHORZE\SUHVVWKH-RJNH\ Ĺ$OWLWXGH ALTITUDE P Ĺ 8 3 L Q G L F D W H V W K H DODUP ZLOO VWDUW ZKHQ 0,10$; WKH DOWLWXGH UHDFKHV (ALARM) (VIB) (LIMIT) DERYH\RXUVHWYDOXH 83ăŁ,1+ăŁ2))ăŁĺ˛ "VIB" type If the following types are selected, the transmitter will vibrate during the warning. Ĺ < R X F D Q K H D U W K H $OWLWXGHGDWDWKURXJKDQ HDUSKRQH RU KHDGVHW E\$FWLYDWLQJWKH6SHHFK IXQFWLRQ OFF TYPE 1 TYPE 2 TYPE 3 OFF OFF ON ON 2 Position 3 Position )LUVWWKHVHWRIDUHIHUHQFHLVUHTXLUHG Alert set : Low side 7KH PRGHO DQG WUDQVPLWWHU WR ZKLFK WKH DOWLWXGHVHQVRUZDVFRQQHFWHGDUHWXUQHGRQ 0RYHWKHFXUVRUWRWKH>5()(5(1&(@RI(;(& LWHP 3UHVVWKH-RJNH\ VRUPRUHSUHVV 0RYHWKHFXUVRUWRWKH'1 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH P $GMXVWPHQWUDQJHa P 83 /,0,7 â§'1 /,0,7 *Atmospheric pressure is changed according to the weather also DWWKHVDPHDLUÂżHOGYDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH P $GMXVWPHQWUDQJHa P 83 /,0,7 â§'1 /,0,7 Common function '1ăŁ,1+ăŁ2))㣠Š' 1 L Q G L F D W H V W K H 5()(5(1&(ăŁ(;(& DODUP ZLOO VWDUW ZKHQ 63((&+ăŁ,1+6:ăŁ18// WKH DOWLWXGH UHDFKHV EHORZ\RXUVHWYDOXH Ĺ6ZLWFKVHOHFWLRQ *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 77 VARIO : Display of SBS-01A / SBS-01G(Option), and alarm setup *An altitude sensor or GPS sensor must be installed in the aircraft. 9$5,2LVDVFUHHQZKLFKGLVSOD\VVHWVXSWKH variometer information from an optional altitude sensor or GPS sensor. 7KHYDULRPHWHURIWKHPRGHOZKLFKLVĂ\LQJFDQ be known. ,ILWEHFRPHVKLJKHURUORZHUWKDQWKHVHWWLQJDQ alarm and/or vibration will alert you. â Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER". Ĺ7KH PD[LPXP DQG WKH PLQLPXP ZKHQSRZHULQJ21DUHVKRZQ Ĺ0D[LPXPDQGPLQLPXPdate reset by pressing the Jog key for 1 second. Ĺ6HOHFW>9$5,2@LQWKH7(/(0(75<VFUHHQDQGDFFHVVWKH VHWXSVFUHHQVKRZQEHORZE\SUHVVWKH-RJNH\ Ĺ9DULRPHWHU VARIO PV Ĺ83LQGLFDWHVWKHDODUP Z L O O V W D U W Z K H Q W K H 0,10$; YDULR UHDFKHV DERYH (ALARM) (VIB) (LIMIT) \RXUVHWYDOXH 83ăŁ,1+ăŁ2))ăŁĺ˛ Common function 78 "VIB" type If the following types are selected, the transmitter will vibrate during the warning. '1ăŁ,1+ăŁ2))㣠Š' 1 L Q G L F D W H V W K H DODUP ZLOO VWDUW ZKHQ 63((&+ăŁ,1+6:ăŁ18// W K H Y D U L R U H D F K H V EHORZ\RXUVHWYDOXH Ĺ6ZLWFKVHOHFWLRQ Ĺ < R X F D Q K H D U W K H 9DULR GDWD WKURXJK DQ HDUSKRQH RU KHDGVHW E\$FWLYDWLQJWKH6SHHFK IXQFWLRQ OFF TYPE 1 TYPE 2 TYPE 3 OFF OFF ON ON 2 Position 3 Position Alert set : Rise side Alert set : Low side 0RYHWKHFXUVRUWRWKH83 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH PV $GMXVWPHQWUDQJHa PV 83 /,0,7 â§'1 /,0,7 0RYHWKHFXUVRUWRWKH'1 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH PV $GMXVWPHQWUDQJHa PV 83 /,0,7 â§'1 /,0,7 *When the + - key simultaneous press, the rate is reset to the initial value. *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ DISTANCE : Display of SBS-01G(Option), and alarm setup *An GPS sensor must be installed in the aircraft. The Distance screen displays and sets altitude data from an SBS-01G GPS Sensor (sold separately), and allows the distance to the airborne aircraft to be read by the transmitter. When the aircraft flies inside or outside the set distance an alarm and vibration alerts the pilot. *Positioning time of GPS A short time is required until the positioning of the GPS is established. In the meantime, don't move the model during this process. Wait until the GPS sensor's LED turns solid green. If it is blinking green it is still acquiring the satellites signals. â Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER". Ĺ7KLVLQGLFDWHVWKHUHFHLYLQJDFFXUDF\IURPD*36VDWHOOLWH:KHQ WKUHH EDUV DUH GLVSOD\HG WKH *36 LV UHDG\ IRU XVH 3XVKLQJ >5()(5(1&(@VHWVWKHFXUUHQWDLUFUDIWSRVLWLRQDVWKHVWDUWLQJSRLQW Ĺ&XUUHQWGLVWDQFH Ĺ 7 K L V L Q G L F D W H V 0 D [ L P X P 'LVWDQFHWKHDLUFUDIWĂHZWR Ĺ 0 D [ L P X P G D W H U H V H W E \ SUHVVLQJ WKH Jog key IRU VHFRQG Ĺ6HOHFW >',67$1&(@ LQ WKH 7(/(0(75< VFUHHQ DQG DFFHVV WKHVHWXSVFUHHQVKRZQEHORZE\SUHVVWKH-RJNH\ Ĺ7KH 83 DQ DODUP LV J H Q H U D W H G Z K H Q W K H V H W Y D O X H L V H[FHHGHG 12 P 0$; P (ALARM) (VIB) (LIMIT) 83ăŁ,1+ăŁ2))ăŁP '1ăŁ,1+ăŁ2))ăŁP 5()(5(1&(ăŁ(;(& 63((&+ăŁ,1+6:ăŁ18// "VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3 Ĺ6ZLWFKVHOHFWLRQ Ĺ < R X F D Q K H D U W K H 'LVWDQFH GDWD WKURXJK DQ HDUSKRQH RUKHDGVHW E\$FWLYDWLQJWKH6SHHFK IXQFWLRQ OFF OFF OFF ON ON 2 Position 3 Position 6HWWLQJWKHUHIHUHQFHSRVLWLRQ 6HWWLQJDWRRFORVHDOHUWGLVWDQFH 7XUQ RQ WKH WUDQVPLWWHU DQG WKH PRGHO ZLWK WKH*36VHQVRULQVWDOOHGLQLW :DLW IRU WKH *36 DFFXUDF\ LQGLFDWRU WR GLVSOD\WKUHHEDUV 0RYH WKH FXUVRU WR 5()(5(1&( >(;(&@ DQG SUHVV WKH -RJ NH\ V RU PRUH SUHVV 7KH PRGHOVFXUUHQWSRVLWLRQLVQRZVWRUHGDQGWKH GLVWDQFHLVVHWWRP 0RYHWKHFXUVRUWRWKH'1 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH P $GMXVWPHQWUDQJHa P 83 /,0,7 â§'1 /,0,7 *Now, the position of the present model was set to 0 m. Setting a "too far" alert distance Common function Ĺ7KH '1 DQ DODUP LV JHQHUDWHG ZKHQ WKH GLVWDQFHGURSVEHORZ WKHVHWYDOXH DISTANCE *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 0RYHWKHFXUVRUWRWKH83 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH P $GMXVWPHQWUDQJHa P 83 /,0,7 â§'1 /,0,7 *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 79 â 2nd page of [DISTANCE] Ĺ6HOHFW>',67$1&(@LQWKH7(/(0(75<VFUHHQDQGDFFHVV WKHVHWXSVFUHHQVKRZQEHORZE\SUHVVWKH-RJNH\ Ĺ-RJNH\SUHVVDVLGHPDGHSDJH DISTANCE 12 02'(ăŁ685)$&( POSITION 1 bĺ˛ĺ˛ E= bĺ˛ĺ˛ Ĺ&XUUHQWSRVLWLRQGLVSOD\ 11RUWKODWLWXGH((DVWORQJLWXGH 66RXWKODWLWXGH::HVWORQJLWXGH Common function Ĺ $ O W L W X G H F D O F X O D W H G D V H L W K H U V W U D L J K W O L Q H GLVWDQFH VODQW RU VXUIDFH GLVWDQFH RQ D PDS FDQ DOVREHVHOHFWHG NT SLA Altitude SURFACE 7ZRGLVWDQFHFDOFXODWLRQPHWKRGVDUHDYDLODEOH 6XUIDFH VWUDLJKWOLQHGLVWDQFH DQG6ODQWPD\ EHVHOHFWHG 6HOHFWSDJHE\-RJNH\SUHVVVLGHIURPWKH ',67$1&(VFUHHQ 6HOHFW 6/$17! 685)$&(! QH[W WR 02'( SUHVVWKHNH\ 80 SPEED : Display of SBS-01G(Option), and alarm setup *An GPS sensor must be installed in the aircraft. The speed screen displays and sets the speed data and with a tail wind, the displayed speed increases. from an SBS-01G (GPS sensor) sold separately. â Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER". The speed of the aircraft during flight can be displayed. *Positioning time of GPS After flight, the maximum speed during flight A short time is required until the positioning of the GPS can be viewed. Because this speed is based on is established. In the meantime, don't move the model position data from a GPS satellite, the ground speed during this process. Wait until the GPS sensor's LED turns is displayed instead of air speed. Consequently, solid green. If it is blinking green it is still acquiring the satellites signals. with a head wind, the displayed speed decreases Ĺ7KH'1WKDWDQDODUP LV JHQHUDWHG ZKHQ W K H V S H H G G U R S V EHORZWKHVHWYDOXH 83ăŁ,1+ăŁ2))ăŁĺ˛ '1ăŁ,1+ăŁ2))㣠transmitter will vibrate during the warning. TYPE 1 63((&+ăŁ,1+6:ăŁ18// TYPE 2 TYPE 3 Ĺ6ZLWFKVHOHFWLRQ Ĺ < R X F D Q K H D U W K H 6SHHG GDWD WKURXJK DQ HDUSKRQHRUKHDGVHWE\ $FWLYDWLQJ WKH 6SHHFK IXQFWLRQ OFF OFF OFF ON ON 2 Position 3 Position $OHUWVHWWLQJZKHQVSHHGLQFUHDVHV $OHUWVHWWLQJZKHQVSHHGGHFUHDVHV 0RYHWKHFXUVRUWRWKH83 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH NPK $GMXVWPHQWUDQJHa NPK 83 /,0,7 â§'1 /,0,7 0RYHWKHFXUVRUWRWKH'1 $/(57 LWHP 6HOHFWWKH$&7PRGHE\SUHVVWKHNH\ 0RYHWKHFXUVRUWRWKH83 /,0,7 >YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH NPK $GMXVWPHQWUDQJHa NPK 83 /,0,7 â§'1 /,0,7 *When the + - key simultaneous press, the rate is reset to the initial value. *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ Common function Ĺ7KLVLQGLFDWHVWKHUHFHLYLQJDFFXUDF\IURPD*36VDWHOOLWH:KHQ WKUHH EDUV DUH GLVSOD\HG WKH *36 LV UHDG\ IRU XVH 6SHHG LV QRW GLVSOD\HGZKHQUHFHLYLQJDFFXUDF\LVEDG Ĺ&XUUHQWVSHHG Ĺ6HOHFW >63(('@ LQ WKH 7(/(0(75< VFUHHQ DQG DFFHVV WKH Ĺ7KLVLQGLFDWHV0D[LPXPVSHHGWKH VHWXSVFUHHQVKRZQEHORZE\SUHVVWKH-RJNH\ DLUFUDIWĂHZWR SPEED âŤÚźâŹ Ĺ0D[LPXP GDWH UHVHW E\ SUHVVLQJ Ĺ7KH 83WKDW DQ DODUP NPK WKHJog keyIRUVHFRQG LV JHQHUDWHG ZKHQ MAX= NPK W K H V H W Y D O X H L V "VIB" type (ALARM) (VIB) (LIMIT) H[FHHGHG If the following types are selected, the 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ *Speed alarm precaution Since the GPS speed sensor displays the ground speed, it cannot be used as a stall alarm. For example, an aircraft that stalls at 50km/h will stall if the tailwind is 5km/h or greater even through 55km/h is displayed by ground speed. In addition, with an aircraft that will disintegrate in midďŹight at 400km/h at an over-speed alarm, when the headwind reaches 30km/h the airplane will disintegrate in midair due to over speeding even at a ground speed of 370km/h. 81 BATTERY / EXT-VOLT: Display of SBS-01V(Option), and alarm setup *SBS-01V must be installed in the aircraft. ,QWKLVVFUHHQWKHEDWWHU\YROWDJHLVGLVSOD\HG ,Q RUGHU WR XVH WKLV IXQFWLRQ LW LV QHFHVVDU\ WR connect of R3008SB â SBS-01V â Battery SBS-01V measures two batteries. The drive battery connected to two lines is displayed on EXTVOLT. The battery for receivers connected to 3P lines is displayed here. Ĺ6HOHFW >%$77(5<@ LQ WKH 7(/(0(75< VFUHHQ DQG DFFHVVWKHVHWXSVFUHHQVKRZQEHORZE\SUHVVWKH -RJNH\ BATTERY MIN/MAX= Ĺ'1 ZLOO VKRZ WKDW DQ DODUP ZLOO VWDUW ZKHQ WKH (;792/7 GURSV EHORZWKHVHWYDOXH Ĺ%DWWHU\YROWDJH Ĺ7KH PD[LPXP DQG WKH PLQLPXP ZKHQSRZHULQJ21DUHVKRZQ Ĺ0D[LPXPDQGPLQLPXPdate reset by pressing the Jog key for 1 second. 9 99 "VIB" type (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 63((&+ăŁ,1+6:ăŁ18// TYPE 2 TYPE 3 Ĺ6ZLWFKVHOHFWLRQ OFF Common function Ĺ < R X F D Q K H D U W K H % D W W H U \ GDWD WKURXJK DQ HDUSKRQH RU KHDGVHW E\ $FWLYDWLQJ WKH 6SHHFKIXQFWLRQ ON Ĺ'1 ZLOO VKRZ WKDW DQ DODUP ZLOO VWDUW ZKHQ WKH (;792/7 GURSV EHORZWKHVHWYDOXH ON 2 Position Ĺ6HOHFW >(;792/7@ LQ WKH 7(/(0(75< VFUHHQ DQG DFFHVVWKHVHWXSVFUHHQVKRZQEHORZE\SUHVVWKH -RJNH\ EXT-VOLT MIN/MAX= OFF OFF 3 Position Ĺ(;7YROWDJH Ĺ7KH PD[LPXP DQG WKH PLQLPXP ZKHQSRZHULQJ21DUHVKRZQ Ĺ0D[LPXPDQGPLQLPXPdate reset by pressing the Jog key for 1 second. 9 99 "VIB" type If the following types are selected, the transmitter will vibrate during the warning. (ALARM) (VIB) (LIMIT) '1ăŁ,1+ăŁ2))ăŁ9 TYPE 1 63((&+ăŁ,1+6:ăŁ18// TYPE 2 TYPE 3 Ĺ YDOXH@LWHP $MXVWWKHUDWHE\SUHVVWKHNH\ ,QLWLDOYDOXH9 $GMXVWPHQWUDQJHa9 %$77(5< $GMXVWPHQWUDQJHa9 (;792/7 *When the + - key simultaneous press, the rate is reset to the initial value. 7R WHUPLQDWH WKH LQSXW DQG UHWXUQ WR WKH RULJLQDOVWDWHWRXFKWKH(1'NH\ 82 OFF OFF ON 3 Position Sensor Slot SENSOR (Common) Function This screen registers the telemetry sensors used with the transmitter. When only one of a certain type of sensor is used, this setting is unnecessary and the sensor can be used by simply connecting it to the S.BUS2 port of the transmitter. When using 2 or more of the same kind of sensor, they must be registered here. [What is a slot?] 6HUYRVDUHFODVVLÂżHGE\&+EXWsensorsDUHFODVVLÂżHGLQXQLWVFDOOHG"slot". There are slots from 1R to 1R. $OWLWXGHVHQVRUV*36VHQVRUV and other data sensor units may use PXOWLSOHVORWV. Using a sensor which uses two or more slots, the required number of slots is automatically assigned by setting up a start slot. When 2 or more of the same kind of sensor are used, the sensors themselves must allocate unused slots and memorize that slot. â The "SENSOR" of a menu is chosen, and Jog key press. 123456 ăŁ6%67 ăŁ6%6502 ăŁ6%6$ 6%6$ 6%6$ ăŁ6%69 SENSOR SLOT 123456 SBS-01V ăŁ6%6* SBS-01G 10 SBS-01G 11 SBS-01G 12 SBS-01G â 8 slots SBS-01G is used. â Slot number â 3 slots SBS-01A is used. ďź Assignable slot ďź â SensorIDďźWhen multiple sensors of the same type are not used, ID is unnecessary. *Altimeter, GPS, and other sensors that display a large amount of data require multiple slots. *Depending on the type of sensor, the slot numbers that can be allocated may be limited. The required number of slots 1 slot The number which can be used as a start slot 1 slot 1 âź 31 Voltage(SBS-01V) 2 slot Altitude(SBS-01A) 3 slot GPS(SBS-01G) TEMP125-F1713 8 slot 1 slot VARIO-F1712 2 slot VARIO-F1672 2 slot CURR-F1678 3 slot GPS-F1675 8 slot 1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,18,19,20 ,21,22,24,25,26,27,28,29,30 1,2,3,4,5,8,9,10,11,12,13,16,17,18,19,20,21,24 ,25,26,27,28,29 8,16,24 1 âź 31 1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,18,19,20 ,21,22,24,25,26,27,28,29,30 1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,18,19,20 ,21,22,24,25,26,27,28,29,30 1,2,3,4,5,8,9,10,11,12,13,16,17,18,19,20,21,24 ,25,26,27,28,29 8,16,24 Sensor TEMP(SBS-01T) RPM(SBS01RM,SBS01RO) Common function SENSOR SLOT â Jog key presses side and makes it 2 pages. Selling area 1 âź 31 Global Europe 83 â REGISTERďźWhen using multiple telemetry sensors of the same type.ďź 7KLVIXQFWLRQUHJLVWHUVDQDGGLWLRQDOVHQVRU&RQQHFWWKHVHQVRUDVVKRZQLQWKHÂżJXUHDQGUHJLVWHULWE\ WKHIROORZLQJSURFHGXUH7KHVHQVRU,'LVUHJLVWHUHGLQWKHWUDQVPLWWHU Sensor connect Receiver battery Hub Sensor Connect a sensor to add T10J Method Calling the setting screen Common function ⥠Select "SENSOR" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ďź â˘ Open the setting screen by pressing the Jog key. ďź1 secondďź âŁ Jog key presses side and makes it 6pages. SENSOR SLOT 123456 ăŁ6%67 ăŁ6%6502 ăŁ6%6$ 6%6$ 6%6$ ăŁ6%69 SENSOR SLOT 31 Left 1-time press or Right 10time press 123456 INHBIT ăŁ5(*,67(5 ăŁ6(166/27 ăŁ,1,7,$/,=( ăŁ$//&/($5 Sensor register â "REGISTER" in SENSOR SLOT page 6 is chosen by Jog key. ⥠Press the Jog key for 1 second. â ConďŹrmation message "sure?" blinks. ⢠Press the Jog key. â A confirmation "beep" sounds when complete. â "COMU-ERROR" : When the number of slots needed in registration is insufficient, an error is displayed and registration cannot be performed. 84 â SENS SLOT This procedure changes the slot number of one registered sensor. Sensor connection Receiver battery Hub Sensor Connect a sensor to add T10J Calling the setting screen â "SENS SLOT" in SENSOR SLOT page 6 is chosen by Jog key. ⥠Jog key press. SLOT SETTING READ 67$576/27 âŤÚŮŽŮŽâŹĺ˛ĺ˛ĺ˛ 6/27/(1*7+ âŤŮŽŮŽâŹ 7<3( ĺ˛ĺ˛ĺ˛ĺ˛ŮŮŮŮ ,' âŤŮŽŮŽŮŽŮŽŮŽâŹ â "COMU-ERROR" when reading goes wrong. Common function SENSOR â READ is chosen and Jog key is pressed â "sure?" â Jog key is pressed. â Number is chosen, Input a number by the ďź key or â key. *Referred to ďź Assignable slot ďź â Once the sensor is read correctly, the Sensor ID will be displayed 85 â INITIALIZE This function returns the slot setting and alarm setting of each sensor to their initial value (shipped state). Various sensors can be used one by one. *The slot number memorized at each sensor cannot be initialized. Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "SENSOR" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź âŁ Jog key presses side and makes it 6 pages SENSOR SLOT 123456 Common function ăŁ6%67 ăŁ6%6502 ăŁ6%6$ 6%6$ 6%6$ ăŁ6%69 SENSOR SLOT Left 1-time press or Right 10time press 31 INHBIT ăŁ5(*,67(5 ăŁ6(166/27 ăŁ,1,7,$/,=( ăŁ$//&/($5 Initialize â "INITIALIZE" in SENSOR SLOT page 6 is chosen by Jog key. ⥠Press the Jog key for 1 second. â ConďŹrmation message "sure?" blinks. 86 123456 ⢠Press the Jog key. â The initialization is done when "COMPLETE" is shown. â ALL CLEAR 7KLVIXQFWLRQVHWVDOOWKHVORWVWR,1+6HQVRUVFDQQRWEHXVHGHYHQLIFRQQHFWHGWRWKHUHFHLYHU$OOWKH alarm settings of each sensor are also cleared. *The slot number memorized at each sensor is not initialized. Calling the setting screen ⥠Select "SENSOR" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ďź â˘ Open the setting screen by pressing the Jog key. ďź1 secondďź âŁ Jog key presses side and makes it 6 pages SENSOR SLOT 123456 Left 1-time press or Right 10time press 31 123456 INHBIT ăŁ5(*,67(5 ăŁ6(166/27 ăŁ,1,7,$/,=( ăŁ$//&/($5 All clear â "ALL CLEAR" in SENSOR SLOT page 6 is chosen by Jog key. ⥠Press the Jog key for 1 second. â ConďŹrmation message "sure?" blinks. Common function ăŁ6%67 ăŁ6%6502 ăŁ6%6$ 6%6$ 6%6$ ăŁ6%69 SENSOR SLOT ⢠Press the Jog key. â The clearing is done when "COMPLETE" is shown. 87 â Manually assigning a sensor slot number $VORWQXPEHUFDQEHDVVLJQHGZLWKRXWFRQQHFWLQJWKHVHQVRUWRWKHWUDQVPLWWHU,QDPDQXDOVHWLWLV required to store a start slot number in a sensor. Calling the setting screen ⥠Select "SENSOR" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ďź â˘ Open the setting screen by pressing the Jog key. ďź1 secondďź âŁ Jog key is pressed in a side and it searches for an empty slot. (INHIBIT). SENSOR SLOT 123456 Common function ăŁ6%67 ăŁ6%6502 ăŁ6%6$ 6%6$ 6%6$ ăŁ6%69 SENSOR SLOT 13 14 15 16 17 18 123456 SBS-01G SBS-01G SBS-01G INHIBIT INHIBIT INHIBIT Assignment of slot â When an INHIBIT slot is selected and the Jog key is pressed, a list of sensors that can be assigned to that slot is displayed. *Refer to the table. 88 ⥠Select the sensor you want to assign and press the Jog key. ⢠Press the END key. END SBUS LINK S.BUS servo link (Common) Function An S.BUS servo can memorize the channel and various settings you input. Servo setting can be performed on the T10J screen by wiring the servo DVVKRZQLQWKHÂżJXUH * With some S.BUS(2) servos, there are some functions with FDQQRW EH XVHG ,I D IXQFWLRQ FDQQRW EH XVHG WKH GLVSOD\ screen will change. (Only the function which can be used by a servo is displayed.) $IWHUUHDGLQJFRPSOHWLRQZLWKFRQQHFWLRQRIWKHDERYHÂżJXUH if a stick is moved, the test of operation of the servo can be operated and carried out. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "SBUS LINK" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź MODE IN ⣠Press the Jog key for 1 second. S.BUS READ SX6 (NO LINK) PLEASE DO NOT YET CONNECT A SERVO ďź1 secondďź â¤ Connect a S.BUS servo to set up. Common function S.BUS SX Receiver battery CAUTION HUB â 'RQ WFRQQHFWDVHUYRXQWLO 02'(,1 T10J S.BUS/ S.BUS2 Servo Ĺś2WKHUZLVHDVHUYRZLOOYLEUDWHDQG EUHDNGRZQ S.BUS Servo setting ⤠"READ" is chosen by Jog key, Press the Jog key for 1 second. ⼠READ is completed and the item in which data of S.BUS servo and a setup are possible is displayed. * "COMU-ERROR" : It is failure of READ. Check a servo and connection. ⌠S.BUS servo is set up. ⧠"WRITE" is chosen and Jog key is pressed for 1 second. The writing is done when "COMPLETE" is shown. Next page S.BUS servo function 89 S.BUS Servo Description of function of each parameter *There are a function which can be used according to the kind of servo, and an impossible function. ⢠ID Displays the ID of the servo whose parameters are to be read. It cannot be changed. ⢠Channel Channel of the S.BUS system assigned to the servo. Always assign a channel before use. ⢠Reverse The direction in which the servo rotates can be changed. ⢠Servo type When "Retractable" is selected and the servo has been continuously stopped for 30 seconds, the dead band expands and unnecessary hold current due to external force is eliminated. When a new control signal enters, normal operation is resumed. When using the servo as a landing gear servo, select "Retractable". Also adjust the servo travel to match the landing gear movement range. ⢠Soft Start Restricts operation in the speciďŹed direction the instant the power is turned on. By using this setting, the ďŹrst initial movement when the power is turned on slowly moves the servo to the speciďŹed position. ⢠Stop Mode The state of the servo when the servo input signal is lost can be speciďŹed. The "Hold" mode setting holds the servo in its last commanded position even if using AM or FM system. Common function ⢠Smoother This function changes smoothness of the servo operation relative to stick movement changes. Smooth setting is used for normal ďŹight. Select the "OFF" mode when quick operation is necessary such as 3D. ⢠Neutral OďŹset The neutral position can be changed. When the neutral oďŹset is large value, the servo's range of travel is restricted on one side. ⢠Speed Control Speeds can be matched by specifying the operating speed. The speed of multiple servos can be matched without being affected by motor fluctuations. This is effective for load torques below the maximum torque. However, note that the maximum speed will not be exceed what the servo is capable of even if the servos operating voltage is increased. ⢠Dead band The dead band angle at stopping can be speciďŹed. [Relationship between dead band set value and servo operation] Small Äş Dead band angle is small and the servo is immediately operated by a small signal change. Large Äş Dead band angle is large and the servo does not operate at small signal changes. (Note) If the dead band angle is too small, the servo will operate continuously and the current consumption will increase and the life of the servo will be shortened. ⢠Travel Adjust The left and right travels centered about the neutral position can be set independently. ⢠Boost The minimum current applied to the internal motor when starting the servo can be set. Since a small travel does not start the motor, it essentially feels like the dead band was expanded. The motor can be immediately started by adjusting the minimum current which can start the motor. [Relationship between boost set value and servo operation] Small Äş Motor reacts to a minute current and operation becomes smooth. Large Äş Initial response improves and output torque increases. However, if the torque is too large, operation will become rough. 90 ⢠Boost ON/OFF OFF : It is the boost ON at the time of low-speed operation.(In the case of usual) ON : It is always the boost ON.(When quick operation is hope) ⢠Damper The characteristic when the servo is stopped can be set. When smaller than the standard value, the characteristic becomes an overshoot characteristic. If the value is larger than the standard value, the brake is applied before the stop position. Especially, when a large load is applied, overshoot, etc. are suppressed by inertia and hunting may occur, depending on the conditions. If hunting (phenomena which cause the servo to oscillate) occurs even though the Dead Band, Stretcher, Boost and other parameters are suitable, adjust this parameter to a value larger than the initial value. [Relationship between damper set value and servo operation] Small Äş When you want to overshoot. Set so that hunting does not occur. Large Äş When you want to operate so that braking is not applied. However, it will feel like the servo response has worsened. (Note) If used in the hunting state, not only will the current consumption increase, but the life of the servo will also be shortened. ⢠Stretcher This is used when stopping hunting, etc., but the holding characteristic changes as shown below. [Relationship between stretcher and servo operation] Small Äş Servo holding force becomes weaker. Large Äş Servo holding force becomes stronger. (Note) When this parameter is large, the current consumption increases. ⢠Buzzer When the power supply of a servo is previously turned on at the time of a power supply injection without taking transmit of a transmitter, the buzzer sound of about 2.5 Hz continues sounding from a servo. Common function The servo hold characteristic can be set. The torque which attempts to return the servo to the target position when the current servo position has deviated from the target position can be adjusted. (Even when the transmit of a transmitter is taken out previously, a buzzer becomes until the signal of a servo is outputted normally, but it is not unusual.) The transmitter has been turned OFF ahead of a servo power supply â The buzzer sound of about 1.25 Hz continues sounding as servo power supply end failure alarm. (Do not insert or remove the servo connector while the receiver power is ON. A buzzer may sound by incorrect recognition.) *Buzzer sound is generated by vibrating the motor of a servo. Since current is consumed and a servo generates heat, please do not operate the number more than needed or do not continue sounding a buzzer for a long time. 91 MDL-TRANS Model transfer Function (Common) *T10J does not carry out normal operation during data transfer. Transmission of model data is possible with T10J transmitters. Data transfer is performed by the radio. The MDL-TRANS function works with the current model you are using in the transmitter. As for the receiving transmitter, any data on the current model that is receiving the information will be over-written. Method CAUTION $OZD\V FKHFN VHUYR GLUHFWLRQ SULRU WR HYHU\ IOLJKW DV DQ DGGLWLRQDO SUHFDXWLRQ WR FRQILUP SURSHUPRGHOGDWHKRRNXSVDQGUDGLRIXQFWLRQ NOTE: MDL-TRANS between two T10J radios should be performed within a 2-meter range. Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "MDL-TRANS" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź Common function MDL-TRANS MODEďź T R A N S F E RďźT10J o f d a t a origin ďź ďź R E C E I V Eďź T 1 0 J w h i c h receives dataďź Execution of transmission/ reception Model transfer â MDL-TRANS between two T10J radios should be performed within â In each T10J, the ďź or â key is pressed and it is made "TRANSFER" and "RECEIVE". ďź âĄ Select "Execute" with the Jog key. â or â "TRANSFER"ďźT10J of data origin "RECEIVE"ďźT10J which receives data Selection rangeďźTRANSFER, RECEIVE â From T8J to T10J, data transfer is possible. In that case, TYPE of T10J on the "RECEIVER" side is changed into "T8J" by ďźâ key. However, data cannot be sent to T8J from T10J. 92 2-meter range. ⢠Hold down the Jog key [ each T10J ]. ďź1 second ) ďź â "COMPLETE" is displayed and the mode transfer is ďŹnished. â If data is not being transmitted, the receiving transmitter returns to normal operation 10 seconds after execution. At this time, "Failure" (not transmitting) is displayed. TRAINER Trainer (Common) Function 6LQFHWKHFKDQQHODQGRSHUDWLRQPRGHXVHGLQWUDLQLQJFDQEHVHOHFWHGWKHWUDLQLQJGLIÂżFXOW\FDQEHVHW to match the studentâs level. The trainer function can be used by connecting the instructorâs transmitter to the studentâs transmitter XVLQJDVSHFLDOWUDLQHUFRUG VROGVHSDUDWHO\ 6WXGHQWRSHUDWLRQLVSRVVLEOHE\LQVWUXFWRUVZLWFKRSHUDWLRQ,I the student enters a dangerous situation, control can be immediately switched to the instructor. Trainer code â Four operation modes can be selected at each channel. â The trainer switch is set to switch H. When the trainer function is used, the snap roll function is automatically deactivated. Teacher Student CAUTION Use the trainer function under the following conditions: Trainer function operation modes â FNC mode: The channel set to this mode can be controlled by the student using the mixing set at the instructor s transmitter. (Student settings are returned to their initial value in advance.) â MIX mode: The channel set to this mode is controlled by mixing the instructor and student signals. Correction rudder is applied by the instructor. When this mode is selected, the student s rate is reduced to prevent servo overthrow. The student s rate can also be set. (The student s settings are returned to their initial value in advance.) â NOR mode: The channel set to this mode is controlled by signals from the student s transmitter. (The instructor and student settings must be the same.) â OFF mode: The channel set to this mode cannot be controlled by the student. It can only be controlled by the instructor. Common function â When the instructor uses a T10J transmitter, set the student s transmitter modulation to PPM (for conventional frequency transmitter). (When the student uses a T10J transmitter, the modulation mode does not have to be changed. A PPM signal is always output from the trainer jack.) â Before ďŹight always conďŹrm that all the instructor and student channels operate normally as set. â Always insert the trainer cord as far as it will go and take measures so that the cord will not work loose during use. â Always remove the high frequency module of the student s transmitter. (For module type) â Never turn on the student s transmitter power switch. However, channels not provided at the student s transmitter are controlled by the instructor regardless of the above settings. When other models are selected, the trainer function is deactivated, but the channel settings remain. Example of use â When the FUNC mode is set at the stick channel, helicopter stick operation training is possible even with a 4EX transmitter (4 channels for aircraft). â Control by the instructor is possible by setting only the training channel matched to the student s level to the NORM mode and setting the other channels to the OFF mode. â Trainer Cords Instructor Student Trainer Cords T12FG (FUTM4405) 10J 10C, 9C, 7C, 6EX, 4EX 18MZ,14MZ, 14SG, FX-22, 12Z, 12FG, 8FG, 10J, 8J, 6J 18MZ,14MZ, 14SG, FX-22, 12Z, 12FG, 8FG, 10C, 9C, 7C, 8J, 6J, 4EX T12FG (FUTM4405) and 9C (FUTM4415) Trainer Cords 10J 93 Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź âĄ Select "TRAINER" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź1 secondďź ďźTrainer functionďź â Select the item with the Jog key. TRAINER Function activation â Channel setting mode display Channel Select AUX AUX Common function Select CH mode Display Rate by studentďźat MIX modeďź ďź ChannelDisplay ďź ACROBATIC HELICOPTER 1: AIL ďźAileronďź 6: FLP ďźFlapďź 2: ELEďźElevatorďź 7: AUX 3: THRďźThrottleďź8: AUX 4: RUD ďźRudderďź 5: GER ďźGearďź 1: AIL ďźAileronďź 6: PITďźPITCHďź 2: ELE ďźElevatorďź 7: AUX 3: THR ďźThrottleďź 8: AUX 4: RUD ďźRudderďź 5: GYR ďźGYROďź GLIDER (AF2) *CH9 and CH10 cannot use a trainer function. Trainer function â Function activation â Select the "OFF" by pressing the + key or â key. ďź â Mode setting â ⥠The mode of the channel of hope is chosen by pressing the + key or â key. or ďźWhen MIX mode Selectďź â Student rate setting ⢠Jog key is pressed in a side and a channel is chosen, rate setting by pressing the + key or â key. ďź Rangeďź0 âź 100% Defaultďź30% ďź Selection rangeďźOFF, NOR, FNC, MIXă DefaultďźOFF â When you do not want to use the function select INH. 94 MULTICOPTER 1: AIL ďźAileronďź 6: FL2ďźFlap2ďź 1: AILďźAileronďź 6: AUX 2: ELEďźElevatorďź 7: AI2 ďźAileron2ďź 2: ELEďźElevatorďź 7: AUX 3: MOT ďźMotorďź 8: AUX 3: THRďźThrottleďź8: AUX 4: RUD ďźRudderďź 4: RUD ďźRudderďź 5: FLP ďźFlapďź 5: MOD ďźModeďź â or â or Airplane Function The setting screen of each function is called from the following menu. The function when the model type was set to airplane (ACROBATIC) is displayed here. Power ON â First set the throttle to slow. To menu screen by holding down the + key â Then turn on the power. ďźHome screenďź â When t h e E N D k e y i s pressed, the display returns to the home screen. â When the + key is pressed for 1 second, the menu screen is ďź1 secondďź displayed. ďź END MENU 0(18ĺ˛ĺ˛ĺ˛ĺ˛1 0(18ĺ˛ĺ˛ĺ˛ĺ˛1 ăŁ0'/6(/ ăŁ0'/1$0( ăŁ)$,/6$)( ăŁ5(9(56( ăŁ7,0(5 ăŁ6(592 ăŁ(1'32,17 ăŁ75,0 ăŁ68%75,0 ăŁ30,; ăŁ$8;&+$1 ăŁ3$5$0(7(5 0(18ĺ˛ĺ˛ĺ˛ĺ˛12 MENU 2/3 ăŁ7(/(0(75< ăŁ6(1625 ăŁ6%86/,1. ăŁ0'/75$16 ăŁ75$,1(5 ăŁ$,/',)) Airplane MENU 1/3 ăŁ$,/âŤÚâŹ58' ăŁ97$,/ ăŁ*<526(16 ăŁ(/(921 ăŁ$,/9$725 ăŁ7+5âŤÚâŹ1(('/ ďźSelectionďź â Move the cursor (highlighted) up and down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. 0(18ĺ˛ĺ˛ĺ˛ĺ˛123 MENU 3/3 ăŁ'5(;32 ăŁ)/$3(521 ăŁ$,5%5. ăŁ)/$3âŤ(ÚâŹ/( ăŁ(/(âŤ)ÚâŹ/$3 ăŁ)/$375,0 ăŁ7+5&87 ăŁ,'/('2:1 ăŁ61$352// ăŁ7+5&859( ăŁ3,7&859( ăŁ7+5ĺ˛'(/$< ďźCalling the setting screenďź â Press the Jog key to open the setting screen. 95 key ďź LCD âďź key ââ key âJog key âEND key Refer to "Common Functions" previously described for a description of this function. â Function MENU1/3 MDL-SEL (P.40) TELEMETRY (P.66) D/R, EXPO Model select ďź Model Copy ďź Data reset ďź RX ďź Link Telemetry Display ďź Alarm setup Dual rate ďź EXPO MDL-NAME SENSOR FLAPERON Telemetry sensor (P.43) Model name ďź User name FAIL SAFE (P.45) Fail safe Airplane REVERSE (P.47) Servo reverse TIMER (P.48) Timer SERVO Trim reset ďź Trim step TRAINER ELE â FLAP Program mixing 1 âź 6 AUX-CHAN (P.97) Data reset ďź Model type ďź ATLtrim ďź LCD contrast ďź Back light : mode, time, adjustment ďź Home display ďź Battery alarm ďź Battery vibration ďź Buzzer tone ďź Jog navi ďź Jog light ďź Jog time ďź Telemetry : mode, unit ďź Speech : language, volume ďź Stick position alarm (P.110) (P.111) FLAP TRIM (P.112) Flap trim (P.98) THR.CUT (P.113) Throttle cut (P.99) IDLE DOWN (P.115) Idle down V-Tail (P.100) SNAP ROLL (P.116) Snap roll Gyro mixing (P.101) THR-CURVE (P.117) Throttle curve Elevon (P.102) PIT-CURVE (P.118) PIT-curve Ailvator THR â NEEDL (P.58) (P.108) Elevator â Flap mixing Aileron DiďŹerential AILVATOR (P.56) AUX channel PARAMETER (P.93) Trainer ELEVON (P.53) FLAP â ELE Flap â Elevator mixing GYRO SENS (P.52) Sub trim P.MIX1-6 (P.92) V-TAIL (P.51) AIR-BRK Data transfer of another 10J or 8J Aileron â Rudder (P.50) (P.106) Air brake MDL-TRANS AIL â RUD SUB TRIM (P.89) S.BUS servo set up END POINT (P.104) Flaperon SBUS LINK Servo monitor ďź Servo test TRIM (P.83) AIL-DIFF (P.49) End point 96 MENU3/3 MENU2/3 (P.103) Throttle â Needle Mixing THR DELAY Throttle delay (P.119) AIL-DIFF Aileron diďŹerential (ACROBATIC) Function The left and right aileron differential can be adjusted independently. This function is restricted to 2 servo aileron. CH1 CH7 NOTEďźAileron Differential cannot be used simultaneously with Flaperon or Elevon. If another function is already active, Others WING mix ON is displayed on the screen. After setting the active function to INH , set the Aileron DiďŹerential function to ACT . Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "AIL-DIFF" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź AIL-DIFF ďźAileronďź Aileron1ďźCH1ďźrate Aileron2ďźCH7ďźrate LďźAileron stick Left side rate RďźAileron stick Right side rate Airplane ACT/INH â When INH is selected, the function cannot be used. To use the function, select ACT. â Select the setting item with the Jog key. Aileron DiďŹerential â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â â Aileron rate ⥠Select the "RATE-AIL1" item and move the aileron stick to the left and right and adjust the travel of each servo by pressing the + key or â key. ďź â or or Rangeďź-120 âź +120% Defaultďź+100% â When you do not use a function, set to the "INH" side. â When you want to return to the initial value, press the + key and â key simultaneously. However, when the polarity is changed only the number returns to the initial value. ďźAdjust the "RATE-AIL2" item in the same way as ⥠.ďź 97 AIL â RUD Aileron â Rudder mixing (ACROBATIC) Function Use this mix when you want to mix the rudders with aileron operation. This allows the aircraft to bank at a steep angle. Ĺ:KHQ WKH OLQNDJH GLUHFWLRQ LV UHYHUVHG E\ WKH OLQNDJH DGMXVWPHQWV FDQ EH PDGH E\ FKDQJLQJ WKHUDWHSRODULW\ Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "AIL â RUD" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź $,/ ⍠ÚâŹ58' Activating the function â When not using this function, select INH. Mixing rate Airplane â Select the setting item with the Jog key. Aileron â Rudder Mixing â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź 98 â â Mixing rate ⥠S e l e c t t h e " R AT E " i t em a n d then adjust the mixing rate by pressing the + key or â key. ďź â or or Rangeďź-100 âź +100% Defaultďź+50% â When you do not use a function, set to the "INH" side. â When you want to return the set value to the initial value, press the + key and â key simultaneously. However, polarity does not return. V-TAIL V-Tail (ACROBATIC) Function ďźś-tail This mixing is used with V tail aircraft that combine the elevator and rudder functions. NOTEďźV Tail cannot be used simultaneously with Elevon or Ailevator. When another function is already activated, Other WING mix ON is displayed on the screen. Set the V tail function to ACT after setting the active function to INH. CH2 (CH4) Elevator Rudder Method CH4 (CH2) CH2 Servo ELE1 RUD2 CH4 Servo ELE2 RUD1 Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "V-TAIL" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Activating the function ELE1 rate ELE2 rate ďźRate adjustmentďź RUD2 rate RUD1 rate Airplane â When INH is selected, the function cannot be used. To use the function, select ACT. V-TAIL â Select the setting item with the Jog key. V-TAIL â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Rate adjustment ⥠Select the "RATE" item and then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź-100 âź +100% Defaultďź+50% ďźonly ELE2 : -50%ďź â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. NOTEďźWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and rudder operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. 99 GYRO SENS Gyro sensor (ACROBATIC) Function IOLJKW WKH J\UR ZLOO ORVH FRQWURO RI WKH SODQH¡V DWWLWXGH )URP WKH VWDQGSRLQW RI VDIHW\ ZH UHFRPPHQGWKDWWKH2)) SRVLWLRQDOVREHVHW XVLQJDSRVLWLRQVZLWFK Ĺ & + & + & + & + & + R U & + & + & + FRPELQDWLRQV FDQ EH VHOHFWHG DV WKH VHQVLWLYLW\ VHWWLQJFKDQQHO This function is dedicated mixing for switching the gyro sensitivity and gyro mode (AVCS/ NORMAL) of Futaba airplane use gyros. Up to 3 axes can be set. Ĺ7KH VHQVLWLYLW\ VZLWFK FDQ EH VHOHFWHG DQG WKH VHQVLWLYLW\RIHDFKGLUHFWLRQRIWKHVZLWFKFDQEH VHW 6ZLWFKHV $ WR + ,I WKH DLUSODQH VWDOOV GXULQJ Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "GYRO SENS" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When not using this function, select INH. GYRO SENS Activating the function Gain Channel selection Switch direction Sensitivity switch selection ďźC u r r e n t s w i t c h o p e r a t i n g directionďź Airplane Gyrotype, Gain rate â Select the setting item with the Jog key. ďźGyro typeďź ďźGyro Gainďź â Switches to the sensitivity setting screen of each switch direction when the Jog key is pressed. â When using a Futaba GYA gyro, select gyro type GY. This switches the gyro sensitivity setting item to mode and sensitivity direct reading display. GYRO SENS â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â Sensitivity switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â or ďź â When you do not use a function, set to the "INH" side. â Sensitivity setting channel selection ⢠Select the ďź â "CH" i tem an d or then select the sensitivity setting channel by pressing the + key or â key. RangeďźCH5ăCH5/CH7ă CH5/CH8ăCH5/CH7/CH8 DefaultďźCH5 100 â or RangeďźSwA âź SwHăDefaultďźSwA â Gyro type and sensitivity setting ⣠Press the Jog key and select the sensitivity setting screen you want to set and then set type (gyro type) and rate (gyro sensitivity) of each channel by pressing the +key or â key. ďź"type"ďźRangeďźSTD,GY DefaultďźSTD ďź"rate"ďźRangeďź0 âź 100%ďźSTDďź, NOR100 âź 0 âź AVC100% ďźGYďź Defaultďź50% ďźSTDďź, 0% ďźGYďź â When you want to return the set value to the initial value, press the + key and â key simultaneously. ELEVON Elevon (ACROBATIC) Function CH2 This mixing is used with delta wing, tailess, and disk shaped airplanes that combine the aileron and elevator functions. Connect the CH1 servo to the left aileron and the CH2 servo to the right aileron. CH1 Pitch Ĺ7KHDLOHURQDQGHOHYDWRUWUDYHOFDQEHDGMXVWHGLQGLYLGXDOO\ CH2 NOTEďźElevon cannot be used simultaneously with V-tail or Ailevator functions. You may use Flaperon or DiďŹerential when this function is active. If another function is already active, Other WING mix ON is displayed on the screen. After setting the active function to INH , set the V-tail function to ACT . CH1 Roll Roll Pitch CH1 servo AIL1 ELE2 CH2 servo AIL2 ELE1 Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "ELEVON" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When INH is selected, the function cannot be used. To use the function, select ACT. ELEVON Aileron1ďźCH1ďźrate Aileron2ďźCH2ďźrate ďźAileron rateďź LďźAileron stick Left side rate RďźAileron stick Right side rate Elevator2ďźCH1ďźrate Elevator1ďźCH2ďźrate Airplane Activating the function ďźElevator rateďź â Select the setting item with the Jog key. ELEVON â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Rate set ⥠Select the "RATE" item and then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź-120 âź +120% Defaultďź+100% ďźonly ELE1 : -100%ďź â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. NOTEďźWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and aileron operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. 101 AILVATOR Ailvator (ACROBATIC) Function Ailevator mixes both Ailerons and Elevators together. Or the function can be used separate from your ailerons when you have two (OHYDWRUVHUYRV6LQFHWKHUHDUHDLUFUDIWOLNHMHWÂżJKWHUVWKDWXVHWKH elevators as ailerons, using this function can give you a sense of reality. $LOHURQRSHUDWLRQFDQDOVREHXVHGZLWKHOHYDWRUVHUYRVSHFLÂżFDWLRQV The servos connect to the receiver CH2 and CH8 output. Ĺ(OHYDWRUDQGDLOHURQWUDYHOFDQEHDGMXVWHGLQGLYLGXDOO\ Ĺ&RQĂUPWKHGLUHFWLRQRIRSHUDWLRQEHFDXVHLWLVGLIIHUHQWGHSHQGLQJ RQWKHOLQNDJH CH 6 (CH7) CH 1 CH 2 ďźCH 8ďź Roll Pitch CH 8 ďźCH 2ďź CH2 servo AIL3 ELE1 CH8 servo AIL4 ELE2 NOTEďźAilevator cannot be used simultaneously with V-tail or Elevon functions. When Other WING mix ON displayed on the screen, set the ailvator function to ACT after setting the active function to INH. is Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "AILVATOR" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Airplane â Select the setting item with the Jog key. AILVATOR Activating the function AIL3 Rate set AIL4 Rate set â When INH is selected, the function cannot be used. To use the function, select ACT. ďźRateďź ELE2 Rate set ELE1 Rate set AILVATOR â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Rate set ⥠Select the "RATE" item and then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź-100 âź +100% Defaultďź-50%ďźAIL3, AIL4ďź, -100%ďźELE2ďź,+100%ďźELE1ďź â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. NOTEďźWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and aileron operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. â When used as 2 elevator servos speciďŹcations without aileron operation, set the AIL3 and AIL4 travel to 0%. 102 THR â NEEDL Throttle â Needle mixing (ACROBATIC) Function This function is used when the engine is equipped with a mixture control system (needle control and other mixture adjustments to the engine). The throttle control servo connects to receiver CH8. Ĺ7KHPL[WXUHFDQEHVHWE\SRLQWFXUYHLQUHODWLRQ WRWKHWKURWWOHVWLFN Ĺ$Q DFFHOHUDWLRQ IXQFWLRQ ZKLFK DFFHOHUDWHV WKH HQJLQH WR WKH RSWLPDO PL[WXUH ZKHQ WKH WKURWWOH LV RSHQHGFDQEHVHW NOTEďźThis cannot be used if Ailevator function is active as they cannot be used simultaneously. AILVATOR mix ON is displayed on the screen. Set the THR â NEEDL function to ACT after setting the active function to INH. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR â NEEDL" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â Select the setting item with the Jog key. 7+5 ⍠ÚâŹ1(('/ â When not using this function, select INH. 5 Point curve set ďźCursor moves with a THR stickďź Acceleration rate â The set-up curve is shown Airplane Activating the function Throttle curve â Activating the function â Select the "MIX" ďź it em a n d t h e n select the "ON" by pressing the + key or â key. â or â 5 point curve setting ⥠Select the setting item (P-1 âź P-5) and then set the travel of each point by pressing the + key or â key. â When you do not use a function, set to the "INH" side. Rangeďź0 âź 100% DefaultďźP-1:0%, P-2:25%, P-3:50%, P-4:75%, P-5:100% â Acceleration rate ⢠Select the "ACC" item and adjust the acceleration amount by pressing the + key or â key. Rangeďź0 âź 100%, Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. 103 D/R,EXPO Dual rate ďź EXPO (ACROBATIC) Function D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps Ĺ7KHFRQWUROVXUIDFHDQJOHLVDGMXVWHGE\HDFKGLUHFWLRQRIWKHVZLWFK7KHOHIWDQGULJKW XSDQGGRZQ GLUHFWLRQRIHDFKVZLWFKFDQEHVHWLQGLYLGXDOO\ EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle. Ĺ7KH´¾VLGHPDNHVVHUYRPRYHPHQWVOXJJLVKDQGWKH´¾VLGHPDNHVVHUYRPRYHPHQWVHQVLWLYHQHDUWKH QHXWUDOSRVLWLRQ([SRQHQWLDOLVDSSOLHGWRHQWLUHWKURWWOHVHUYRWUDYHO:KHQWKH´¾VLGHLVLQFUHDVHGWKH VORZVLGHEHFRPHVVOXJJLVKDQGWKHKLJKVLGHEHFRPHVVHQVLWLYH Ĺ6HWWLQJFRUUHVSRQGLQJWRHDFKUDWHRIGXDOUDWH '5 LVSRVVLEOH ([FHSWWKURWWOH 7KHGLUHFWLRQRIHDFK VZLWFKDQGWKHOHIWDQGULJKW XSDQGGRZQ GLUHFWLRQRIHDFKFKDQQHOFDQEHVHWLQGLYLGXDOO\ Switch selectionďźSWďź Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate (exponential) switch. Ĺ'HIDXOWďź$LOHURQďź6ZLWFK' ďź (OHYDWRUďź6ZLWFK$ ďź 5XGGHUďź6ZLWFK% Method Airplane Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "D/R,EXPO" from the menu with the Jog key. ďź ďź1 secondďź â The channel under selection is underlined. Channel selection Dual rate ďźSwitch Directionďź EXPO â The dual rate and exponential settings are displayed by a curve. Switch selection â Channel selection/Select the setting item with the Jog key. 104 ⢠Open the setting screen by pressing the Jog key. ďźSwitch No.ďź ďźD/R and EXPO rate displayďź Top rowďźLeft side ďź down Bottom rowďźRight side ďź up ďź Channel ďź 1ďźAileron 2ďźElevator 3ďźThrottle 4ďźRudder D/R â A channel is chosen by Jog key. Rangeďź1, 2, 4 ⥠Adjust the rate by moving the cursor to D/R with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left (down) or right (up) side and pressing the + key or â key. â ďź Rangeďź 0 âź 140% Defaultďź100% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step â Moving to another setting item of the same channel is possible by Jog key. EXPO â Select the "EXP" item and then select the channel with the Jog key. ⥠Adjust the rate by moving the cursor to EXP with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left (down) or right (up) side and pressing the + key or â key. â ďź Rangeďź1 âź 4 Rangeďź -100 âź +100% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. â Moving to another setting item of the same channel is possible by Jog key. Airplane Adjust the rate of each direction of the dual rate switch and stick by repeating step Switch Change â Select the "SW" item and then select the channel with the Jog key. ⥠A switch is chosen by + key or -key. ďź â or Rangeďź1, 2, 4 RangeďźSwA âź SwH 105 FLAPERON Flaperon (ACROBATIC) Function This mixing function mixes two ailerons and also gives the DLOHURQVDĂDSIXQFWLRQ$LOHURQDQGOHIWDQGULJKWDLOHURQFRQWURO surfaces can be raised at the same time. If this function is used together with air brake function, the aircraft speed can be dropped when landing and is effective in narrow places. Connect the left aileron servo to CH1 (AIL) and the right aileron servo to CH6 (FLP). Ĺ7KH XS DQG GRZQ DQJOH RI WKH OHIW DQG ULJKW DLOHURQ FRQWURO VXUIDFHVFDQEHDGMXVWHGLQGLYLGXDOO\ Ĺ7KHOHIWDQGULJKWĂDSWUDYHOFDQDOVREHDGMXVWHGLQGLYLGXDOO\ CH1 CH6 CH6 servo A i l e r o n Right Aileron Operation Flap Operation Flap1 CH1 servo Left Aileron Flap2 NOTEďźOnly the Flaperon, AileronDiďŹerential, or Elevon functions can be used. They cannot be turned on simultaneously. When another function is already activated, Other WING mix ON is displayed on the screen. Set the Flaperon function to ACT after setting the active function to INH. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. Airplane ďź ďź1 secondďź Activating the function Aileron1ďźCH1ďźrate Aileron2ďźCH6ďźrate Flap2ďźCH1ďźrate Flap1ďźCH6ďźrate â Select the setting item with the Jog key. 106 ⥠Select "FLAPERON" from the menu with the Jog key. FLAPERON â When INH is selected, the function cannot be used. To use the function, select ACT. ďźAileron rateďź LďźAileron stick Left side rate RďźAileron stick Right side rate ďźFlap rateďź Flaperon â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â â Aileron rate ⥠Select "RATE-AIL1" and operate the aileron stick to the left and right and adjust the travel of each servo by pressing the + key or â key. ďź â or or Rangeďź-120 âź +120% Defaultďź100% â When you do not use a function, set to the "INH" side. â When you want to return the set value to the initial value, press the + key and â key simultaneously. However, when the polarity is changed, only the number is returned to the initial value. (The RATE-AIL 2 item is adjusted in the same way as ⥠.ďź ďźWhen ďŹap trim is used, make the settings shown below.ďź â However, set the basic travel with the Flap function in advance.ďźDefaultďź0%ďź â Flap rate ⢠Select the "RATE-FLP2" item and adjust the Flap2 travel by pressing the + key or â key. ďź â or Rangeďź-120 âź +120% Defaultďź+100% â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. Airplane ďźThe RATE-FLP1 item is adjusted in the same way as ⢠. However, the RATE-FLP1 side initial value is -100%.ďź Flaperon ACT CH1 CH6 When flaperon is active, the ailerons can be controlled by the servos connected to CH1 and CH6. The servo travel can be adjusted by the left and right end points. Air brake ACT CH1 CH6 The left and right ailerons can be raised (brake operation) and lowered (flap operation) at the same time by setting SW-C to its lowest position. 107 AIR-BRK Air brake (ACROBATIC) Function This function is used when the air brake is necessary during landing and is turned on and off by switch C (initial setting). Ĺ1RUPDOO\ ZKHQ WKH DLOHURQV DUH XVHG DV D EUDNH WKH\DUHUDLVHG 83VLGH Ĺ:KHQ WKH RSHUDWLRQ PRGH LV ´2)67Âľ RIIVHW WKH DLU EUDNH LV FRQWUROOHG E\ VZLWFK RSHUDWLRQ :KHQ WKHRSHUDWLRQPRGHLV´/,15Âľ OLQHDU WKHDLUEUDNH LV RSHUDWHG OLQHDUO\ DW VZLWFK 21 DQG IURP WKH FRQWUROVWLFNVHWSRVLWLRQ Ĺ,IWKH´/,15ÂľPRGHZDVVHOHFWHGWKHWKURWWOHVWLFN FRQWUROV &+ DQG WKH DLU EUDNH RSHUDWLRQ EXW LW FDQ EH VHSDUDWHG IURP &+ RSHUDWLRQ &+ FRQWURO FDQ EH VZLWFKHG IURP VWLFN WR VWLFN RU WR 95 NQRE +RZHYHU ZKHQ RWKHU WKDQ VWLFN ZDV VHOHFWHG WKH WKURWWOH WULP DQG IXQFWLRQ UHYHUVH IXQFWLRQVFDQQRWEHXVHG Ĺ:KHQ XVHG LQ WKH ´/,15Âľ PRGH DGMXVW WKH WUDYHO ZLWK WKH WKURWWOH VWLFN DW WKH PD[LPXP VORZ VLGH EUDNLQJDPRXQWPD[LPXP â Adjustment item for every wing type Display ďźNormalďź Flaperon Aileron DiďŹerential AIL1(1CH) ELEV(2CH) FLAP(6CH) AIL2(7CH) ----Elevator Flap ----- Aileron1 Elevator Aileron2 ----- Aileron1 Elevator Flap Aileron2 CH2 CH 2 CH 6 CH 1 Method Airplane Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Activating the function Rate set Delay Rate set â Select the setting item with the Jog key. 108 ⥠Select "AIR-BRK" from the menu with the Jog key. AIR-BRK 3CH Control set â When not using this Function select INH. The display of On/ OďŹ is shown when active and assigned to a switch. Switch selection Switch direction Mode â When the LINR operation mode was selected, the current throttle stick position is displayed at the operation reference point and in the bottom row parentheses. Air brake â Activating the function â Select the "MIX" item and then select the "ON" or "OFF" by pressing the + key or â key. ďź â Rate set ⥠Select the "rate" item and adjust the servo travel by pressing the + key or â key. â ďź â or Rangeďź-100 âź +100% Defaultďź+50%ďźELEV only -10%ďź or â When you do not use a function, set to the "INH" side. â When you want to return the set value to the initial value, press the + key and â key simultaneously. However, polarity does not return. â Delay Rate set ⢠Select the "delay" item and adjust the elevator operation delay by pressing the + key or â key. ďź â or â The amount of delay is large at 100%. Rangeďź0 âź 100%ăDefaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. ďźIn the case of change of a switchďź â Switch selection â Select the "SW" i tem an d t h e n select the switch by pressing the + key or â key. ďź â or ďź â or Rangeďź â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN ďźIn the case of change of a modeďź â Mode â S e l e c t t h e ďź â "MOD" item or and select the operation mode by pressing the + key or the â key. RangeďźOFST, LINR DefaultďźOFST Airplane RangeďźSwA âź SwH DefaultďźSwC â Switch direction ⥠Select the ON direction by pressing the + key or â key at the ON direction selection item. â Operation reference point setting ("LINR" mode only) ⥠Select the operation reference point setting item newly displayed at the bottom row of "MOD" and hold the throttle stick at the air brake start point and set the reference point by pressing the Jog key for 1 second. Rangeďź0 âź 100% ďźWhen 3CH control is changed at the time of "LINR"ďź â "LINR" mode 3CH control â Select the "CH3" item and select control by pressing the +key or â key. RangeďźTHR, SwA âź SwH, VR, DT5, DT6 DefaultďźTHR 109 FLAP â ELE Flap â Elevator mixing (ACROBATIC) Function This mixing is used to compensate for pitch FKDQJHV HOHYDWRUGLUHFWLRQ DWĂDSRSHUDWLRQ Ĺ:KHQ WKH PL[LQJ GLUHFWLRQ LV UHYHUVHG E\ WKH OLQNDJH DGMXVWPHQW LV SRVVLEOH E\ FKDQJLQJ WKH UDWHSRODULW\ Ĺ7KHPL[LQJUHIHUHQFHSRLQWFDQEHVKLIWHG 2))6(7 Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "FLAP â ELE" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź )/$3 âŤ( ÚâŹ/( â When not using this function, select INH. Activating the function Mixing rate Airplane Mixing oďŹset rate ďźP r e s e n t f l a p o p e r a t i n g positionďź â Select the setting item with the Jog key. Flap â ElevatorMixing â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â Mixing rate ⥠S e l e c t t h e " R AT E " i t em a n d then adjust the mixing rate by pressing the + key or â key. â â When you want to return the set value to the initial value, press the + key and â key simultaneously. ďźWhen changing the mixing reference pointďź â Mixing reference point oďŹset setting â Select the "OFFSET" item and turn the Flap knob to the point you want to make the mixing reference point and set the reference point by pressing the Jog key for 1 second. Rangeďź-100 âź +100% Defaultďź0% 110 â or Rangeďź-100 âź +100% Defaultďź0% or â When you do not use a function, set to the "INH" side. ďź ďź1 secondďź ELE â FLAP Elevator â Flap mixing (ACROBATIC) Function This mixing is used when you want to apply mixing from elevators WRĂDSV8VXDOO\PL[LQJLVVXFKWKDWWKHĂDSVDUHORZHUHGE\UDLVLQJ the elevators. When used with Fun Fly and other aircraft, small loops are possible. Flap CH6 Ĺ7KHXSVLGHDQGGRZQVLGHUDWHVFDQEHDGMXVWHG Method Elevator CH2 Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "ELE â FLAP" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When not using this Function select INH. The display of On/ OďŹ is shown when active and assigned to a switch. (/( âŤ) ÚâŹ/$3 Activating the function Mixing rate Switch selection Switch direction â Select the setting item with the Jog key. â Sets the ON/OFF direction of the selected switch. â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Airplane ďźElevator down side rateďź ďźElevator up side rateďź â This cursor position operates and chooses an elevator stick. Elevator â FlapMixing â Activating the function â Select the "MIX" item and then select the ON or OFF by pressing the + key or â key. ďź â Switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â or â When you do not use a function, set to the "INH" side. â Switch direction ⢠Select the "POSI " by pressing the + key or â key at the ON direction selection item. ďź â or Rangeďź â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN ďź â or RangeďźSwA âź SwHăDefaultďźSwC â Mixing rate ⣠S e l e c t t h e " R AT E " i t e m a n d then adjust the mixing rate by pressing the + key or â key. Rangeďź-100 âź +100% ďź â or Defaultďź+50% â When you want to return the set value to the initial value, press the + key and â key simultaneously. However, polarity does not return. â RATE â / â cursor position operates and chooses an elevator stick. 111 FLAP TRIM Flap trim (ACROBATIC) Function This function trims the CH6 VR knob. Ĺ7KHWULPWUDYHOFDQEHDGMXVWHG *When the ďŹaperon function is activated ( ACT ), this function is turned on automatically. It can be turned on and oďŹ independently. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "FLAP TRIM" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź FLAP TRIM Activating the function Airplane Flap trim rate â When INH is selected, the function cannot be used. To use the function, select ACT. â Select the setting item with the Jog key. Flap Trim â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. 112 â Flap rate ⥠Select the "RATE" item and then adjust the ďŹap rate by pressing the + key or â key. ďź â or Rangeďź-100 âź +100% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. THR.CUT Throttle cut (ACROBATIC) Function This function cuts (stops) the engine or motor by stick operation. At throttle operation, the rate is adjusted to the position which completely cuts the throttle servo or ESC when the throttle is operated. When Thr.Cut is active, the throttle position is held regardless of the throttle stick position. Ĺ125(6& RSHUDWLRQ PRGH VZLWFKLQJ )RU PRWRU DLUFUDIWVHOHFW(6&)RUPRWRUDLUFUDIWWKHWKURWWOH SRVLWLRQ ZKHQ WKH IXQFWLRQ LV UHVHW FDQ EH VHW VR WKHPRWRUZLOOQRWXQH[SHFWHGO\UXQDWKLJKVSHHG ZKHQ WKH WKURWWOH FXW IXQFWLRQ LV UHVHW :KHQ WKH WKURWWOHVWLFNLVKLJKHUWKDQWKHVHWWKURWWOHSRVLWLRQ WKH WKURWWOH FXW IXQFWLRQ LV QRW UHVHW HYHQ LI WKH VZLWFKLVVHWWR2))6HWWRDVDIHWKURWWOHSRVLWLRQ VORZVLGH Ĺ)XQFWLRQRSHUDWLRQFDQEHVHOHFWHGIURPDPRQJ VZLWFKHV$ âź + Ĺ6HWWKHWKURWWOHFXWIXQFWLRQIRUVDIHW\DOVR Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR.CUT" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Mode Activating the function Cut Position rate Throttle Position Switch selection Switch direction â Select the setting item with the Jog key. â When not using this Function select INH. The display of On/ Off is shown when active and assigned to a switch. Airplane THR.CUT â Adjusts the rate to the position that completely cuts the throttle servo or ESC. â Sets the ON/OFF direction of the selected switch. â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN â The THR item can be set when the operation mode is ESC . The number in parentheses is the current throttle stick position. 113 Throttle Cut â Mode â Select the "MODE" item and then select the mode by pressing the + key or â key. ďź â Activating the function ⥠Select the "MIX" item and then select the oďŹ by pressing the + key or â key. â ďź â or or RangeďźNOR, ESC DefaultďźNOR â When you do not use a function, set to the "INH" side. â "NOR"ďźEngine plane "ESC"ďźElectric motor plane â Switch selection ⢠Select the "SW" item and then select the switch by pressing the + key or â key. ďź â â Switch direction ⣠Select the "POSI" by pressing the + key or â key at the ON direction selection item. ďź â or or Rangeďź RangeďźSwA âź SwH DefaultďźSwA Airplane â Cut Position rate ⤠Select the "RATE" item and then select the cht position by pressing the + key or â key (motor stop). ďź â â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN ďźIn the case of ESC ďź â Function release Throttle Position ⼠Select the "THR" item and then select the release position by THR stick is lowered and Jog key is pressed for 1 second. or â It adjusts to the position where an engine is cut. Rangeďź-30 âź 0 âź +30% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. 114 â Set to a safe low throttle position. Rangeďź0 âź 100% Defaultďź15% IDLE DOWN Idle down (ACROBATIC) Function This function is linked to the air brake switch and gear switch and lowers the engine idle. It is used when engine idle is set high to prevent the HQJLQHIURPVWDOOLQJGXULQJĂLJKWDQG\RXZDQWWR lower engine idle when landing. Ĺ7KHDPRXQWHQJLQHLGOHLVORZHUHGFDQEHVHW Ĺ$WLGOLQJGRZQRSHUDWLRQWKHVWRSOHYHUDGMXVWVWKH LGOHGRZQDPRXQW Ĺ)XQFWLRQRSHUDWLRQFDQEHVHOHFWHGIURPDPRQJ VZLWFKHV$ âź +7KHVZLWFKGLUHFWLRQFDQDOVREH VHOHFWHG Method Calling the setting screen ⥠Select "IDLE DOWN" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź IDLE DOWN Activating the function Idle down rate â When not using this Function select INH. The display of On/ OďŹ is shown when active and assigned to a switch. â Select the setting item with the Jog key. â Sets the ON/OFF direction of the selected switch. â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Idle down â Activating the function â Select the "MIX" item and then select the on or oďŹ by pressing the + key or â key. Airplane Switch selection Switch direction ďź â Switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â or â When you do not use a function, set to the "INH" side. â Switch direction ⢠Select the "POSI" by pressing the + key or â key at the ON direction selection item. Rangeďź â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN ďź â or RangeďźSwA âź SwHăDefaultďźSwC â Idle down rate ⣠Select the "RATE" item and then ad just the idle down rate by pressing the + key or â key. ďź â or Rangeďź0 âź 40% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. â The idle down amount is usually 10% âź 20%. Hold down the aircraft and set the throttle switch to the maximum slow position while the engine is running and adjust the idle drop amount while turning the switch on and oďŹ. 115 SNAP ROLL Snap roll (ACROBATIC) Function This function performs snap roll by switch (SwH). Ĺ7KH UROO GLUHFWLRQ LV VHOHFWHG IURP DPRQJ GLUHFWLRQV 58 /8 5' /' E\ VZLWFKHV Ĺ$VDVDIHW\PHDVXUHDVDIHW\PRGHFDQEHVHWVRWKDWRSHUDWLRQLVQRWSHUIRUPHG HYHQLIDVZLWFKLVPLVWDNHQO\WXUQHGRQZKHQUHWUDFWLQJWKHODQGLQJJHDU Method NOTEďź The trainer function cannot be turned on simultaneously with this function. If the trainer function is active, trainer ACT is displayed on the screen. After setting the trainer function to INH , turn on this function. ďźDirection Switchďź SW1 SW2 1: R/U 2: L/U 3: R/D 4: L/D Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "SNAP ROLL" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Activating the function SNAP ROLL ďźSnap roll directionďź â When INH is selected, the function cannot be used. To use the function, select ACT. Rate set Safe mode set Direction Switch selection Airplane â Select the setting item with the Jog key. Idle down â Activating the function â Select the "MIX" item and then select the "OFF" by pressing the + key or â key. or â Direction switch selection ⥠Select the "DIRC-SW1" and "DIRC-SW2" item and select each switch by pressing the + key or â key. â When you do not use a function, set to the "INH" side. Rangeďź NULL, SwA âź SwH DefaultďźNULL ďź â â Safe mode set ⣠Select the "SAFE-MODE" item and then select the mode by pressing the + key or â key. Rangeďź FREE, CH5+, CH5DefaultďźFREE â Servo Rate set ⢠Switch the DIRC-SW1 or DIRCSW2 in the direction you are wanting to adjust by pressing the + key or â key at the AIL , ELE , and RUD items. Rangeďź-120 âź +120% â Set the R/U, L/U, R/D, and L/D directions. â When a 3 position switch was selected at DIRC-SW1 setting, 1:R/U, 2:L/ U, 3:R/D switching is possible with 1 switch. At this time, DIRC-SW2 cannot be selected. Safe mode setting can set the direction of the landing gear switch. â When CH+ was selected, the safety device sets the landing gear switch to the rear position and the snap switch is not effective even if operated. When the landing gear switch is in the forward position, operation is possible. When CH5was selected, the safety device operates and the snap switch is ineďŹective even if operated. When the landing gear switch is in the rear position, operation is possible. â When FREE was selected: The safety device does not operate regardless of the switch direction. 116 THR-CURVE Throttle curveďźAirplaneďź (ACROBATIC) Function This function sets a 5 point throttle curve so that the engine/motor speed relative to movement of the WKURWWOHVWLFNLVWKHRSWLPXPYDOXHIRUĂLJKW Ĺ$FXUYHFDQEHVHWIRUHDFKVZLWFKSRVLWLRQ However, this function cannot be used when the throttle EXP function was set. When this function is set, the throttle EXP function cannot be used. Method Calling the setting screen ⥠Select "THR-CURVE" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź THR-CURVE Activating the function Switch selection â When not using this function, select INH. â The set-up curve is shown 5 point curve set ďźPresent switch positionďź Airplane â Select the setting item with the Jog key. Throttle curve â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. ďź â or RangeďźSwA âź SwHăDefaultďźSwE â 5 point curve set ⢠By Jog key, either of P-1 to P-5 is chosen. The + key or - key is pressed and a rate is set up. ďź â or Rangeďź0 âź 100% DefaultďźP-1:0%, P-2:25%, P-3:50%, P-4:75%, P-5:100% 117 Pitch curveďźAirplaneďź PIT-CURVE (ACROBATIC) Function This function is a function for the variable pitch propellers of an airplane. 7KHFXUYHRIÂżYHSRLQWVFDQEHVHWXS Ĺ3,7FXUYH IXQFWLRQ FDQQRW EH XVHG ZKHQ DQ $,/9$725IXQFWLRQLV$&7 Ĺ&+RIDSLWFKFDQEHVHWWR&+RU&+ Method Calling the setting screen ⥠Select "PIT-CURVE" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź PIT-CURVE Activating the function Switch selection â When not using this function, select INH. Channel selection â The set-up curve is shown Airplane 5 point curve set ďźPresent switch positionďź â Select the setting item with the Jog key. PIT-curve â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â 5 point curve set ⢠By Jog key, either of P-1 to P-5 is chosen. The + key or - key is pressed and a rate is set up. ďź â or RangeďźSwA âź SwHăDefaultďźSwE ďźWhen a channel is changedďź ďź â or Rangeďź-100 âź +100% DefaultďźP-1:-100%, P-2:-50%, P-3:0%, P-4:+50%, P-5:+100% 118 â Switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â Channel selection â Select the "CH" item and then select the channel by pressing the + key or â key. ďź Rangeďź8CHă5CH Defaultďź8CH â or THR DELAY Throttle delay (ACROBATIC) Function When this function is used, the throttle servo operating speed can be slowed down. ďźPerfect for turbojet engine throttle control, etc.ďź Ĺ7KHDPRXQWRIGHOD\FDQEHVHW Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR DELAY" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź THR DELAY â When INH is selected, the function cannot be used. To use the function, select ACT. Activating the function ďźThrottle delay rateďź â It can be set to slow the servo movement up to +100% â Select the setting item with the Jog key. Airplane Delay Rate set THR DELAY â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â or â Delay Rate set ⥠Select the "RATE" item and then adjust the rate by pressing the + key or â key. ďź â or Rangeďź0 âź 100% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. â When you do not use a function, set to the "INH" side. 119 HELICOPTER Function The setting screen of each function is called from the following menu. The function when the model type was set to helicopter is displayed here. To menu screen by holding down the + key PowerON â First set the throttle to slow. â Then turn on the power. ďźHome screenďź â When t h e E N D k e y i s pressed, the display returns to the home screen. END â When the + key is pressed for ďź1 secondďź 1 second, the menu screen is displayed. ďź MENU 0(18ĺ˛ĺ˛ĺ˛ĺ˛1 0(18ĺ˛ĺ˛ĺ˛ĺ˛ 1 MENU 1/3 ăŁ0'/6(/ ăŁ0'/1$0( ăŁ)$,/6$)( ăŁ5(9(56( ăŁ7,0(5 ăŁ6(592 ăŁ(1'32,17 ăŁ75,0 ăŁ68%75,0 ăŁ30,; ăŁ$8;&+$1 ăŁ3$5$0(7(5 Helicopter 0(18ĺ˛ĺ˛ĺ˛ĺ˛12 MENU 2/3 ăŁ7(/(0(75< ăŁ6(1625 ăŁ6%86/,1. ăŁ0'/75$16 ăŁ75$,1(5 ăŁ&21',7,21 ăŁ6:$6+$)5 ăŁ6:+0,; ăŁ6:+5,1* ăŁ2))6(7 ăŁ'(/$< ăŁ7+5&87 ďźSelectionďź â Move the cursor ( h i g h l i g ht e d ) u p a n d down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. 0(18ĺ˛ĺ˛ĺ˛ĺ˛123 MENU 3/3 120 ăŁ*<526(16 ăŁ'5(;32 ăŁ7+5&859( ăŁ3,7&859( ăŁ5(920,; ăŁ7+5+2/' ăŁ*29(5125 ăŁ+297+5 ăŁ+293,7 ăŁ+, ⍠ءâŹ/23,7 ăŁ7+50,; ăŁ7+5âŤÚâŹ1(('/ ďźCalling the setting screenďź â Press the Jog key to open the setting screen. key ďź LCD âďź key ďźCondition switching at each setting screenďź â Press the jog button for 1 second. When setting conditions with the following function, each setting can be made by switching the condition by pressing the Jog key for 1 second. Throttle curve, Pitch curve, Pitch â Rudder, Gyro sens, HI/ LO-Pitch, OFFSET, Throttle MIX, THR â Needle, Swash MIX ââ key âJog key âEND key Refer to "Common Functions" previously described for a description of this function. â Function MENU1/3 MDL-SEL MENU2/3 (P.40) TELEMETRY MENU3/3 (P.66) GYRO SENS Model select ďź Model Copy ďź Data reset ďź RX ďź Link Telemetry Display ďź Alarm setup Gyro mixing MDL-NAME SENSOR D/R, EXPO Telemetry sensor (P.43) Model name ďź User name FAIL SAFE (P.45) Fail safe REVERSE (P.47) Servo reverse TIMER (P.48) Timer SERVO (P.89) S.BUS servo set up MDL-TRANS (P.92) Pitch curve TRAINER REVO.MIX (P.93) Trainer (Idle-upăť Throttlehold) S W A S H A F R ďźH-1 (P.123) (P.51) Swash AFR SWH.MIX (P.52) Sub trim P.MIX1-6 Program mixing 1 âź 6 AUX-CHAN AUX channel PARAMETER Data reset ďź Model type ďź ATLtrim ďź LCD contrast ďź Back light : mode, time, adjustment ďź Home display ďź Battery alarm ďź Battery vibration ďź Buzzer tone ďź Jog navi ďź Jog light ďź Jog time ďź Telemetry : mode, unit ďź Speech : language, volume ďź Stick position alarm (P.140) (P.141) Governor mixing (P.143) Hovering Throttle (P.124) HOV-PIT (P.144) Hovering Pitch (P.126) HI/LO-PIT (P.145) HI/LO-pitch trim (P.127) THR-MIX (P.146) Swash â Throttle mixing (P.128) THR-NEEDL (P.147) Throttle â Needle mixing Delay THR.CHT (P.138) Throttlehold HOV-THR Trim oďŹset DELAY (P.58) THR HOLD GOVERNOR removesďź Swash RING OFFSET (P.56) (P.122) Swash MIXing SWH.RING (P.53) (P.136) Helicopter Condition SUB TRIM (P.134) Revolution mixing (PIT to RUD) (P.50) Trim reset ďź Trim step PIT-CURVE Data transfer of another 10J or 8J END POINT TRIM THR-CURVE Throttle curve Servo monitor ďź Servo test End point (P.132) Dual rate ďź EXPO SBUS LINK CONDITION (P.49) (P.83) (P.131) (P.129) Throttle cut 121 CONDITION Condition select (Idle-upăťThrottlehold) (HELICOPTER) Function The condition switches (idle up 1/2/3 and throttle hold switch) are not operative at initial setting. Switch setting is performed in advance with the condition select function. Ĺ,QLWLDOO\VHWWRLGOHXS6Z( FHQWHU LGOHXS6Z( IRUZDUG LGOH XS 6Z) IRUZDUG WKURWWOH KROG 6Z* IRUZDUG Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "CONDITION" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When not using this Function select INH. The display of On/ OďŹ is shown when active and assigned to a switch. CONDITION Idle-up setting Throttlehold setting â Select the setting item with the Jog key. ďźActivating thefunctionďź ďźSwitch direction ďź ďźSwitch selection ďź Helicopter Condition select â Activating the function â Select the "INH" item of the condition you want to use and set it to "ON" or "OFF" by pressing the + key or â key. ďź â or â Set conditions you do not want to use to "INH". ďźIn the case of change of a switchďź â Switch selection ⥠A cursor is moved to ďź "Switch selection" and or a switch is changed by ďź key or â key. â RangeďźSwA âź SwH DefaultďźSwEďźIDLE-UP1/2ďź ă SwF ďźIDLE-UP3ďź ăSwGďźTHR-HOLDďź 122 â Switch direction ⢠A cursor is moved to "Switch direction" and a switch direction is changed by ďź key or â key. ďź â or Rangeďź â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN SWASH AFR Swash AFR (HELICOPTER) ďźWhen swash type is H-1, this setting screen is not displayed.ďź Function This is the adjustable function rate (AFR) function when HR3, H-3, HE3, HN3, H-2, H-4, or H4X is selected as the swash type. The ailerons, elevators, and pitch steering angle and direction can be adjusted. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "SWASH AFR" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â Select the setting item with the Jog key. â Depending on the swash type the screen display is diďŹerent. SWASH AFR â When the polarity is changed, the direction of operation is reversed. Rete NOTEďźIf the steering angle is too large, linkage binding may occur . â Travel adjustment of each function â Select each function item of "RATE" and set the rate by pressing the + key or â key. ďź â or Helicopter Swash AFR Rangeďź-100 âź +100% Defaultďź+50% â When you want to return the set value to the initial value, press the + key and â key simultaneously. However, polarity does not return. 123 SWH. MIX Swash mixing (HELICOPTER) Function This mixing is used to correct the bad tendencies of the swash plate in the aileron direction and elevator direction relative to aileron, elevator, and pitch operations. It adjusts the rate of the direction that requires correction so that the servo operates smoothly in the proper direction relative to each operation. Ĺ7KHFRUUHFWLRQDPRXQWRIHDFKFRQGLWLRQFDQEH VHW Ĺ7KH OHIW DQG ULJKW XS DQG GRZQ FRUUHFWLRQ DPRXQWFDQEHVHWIRUHDFKFRQGLWLRQ Example of use: Using to correct bad roll tendencies â AIL â ELE is set to ON. ⥠ACTION/ON is common to all conditions. The rate of unused conditions is set to 0%. ⢠When the nose drops at right roll and the right side rate is adjusted in the "+" direction, the elevators move to the up side when the right aileron is deďŹected. Left roll can be adjusted by left side rate. However, since the left and right ailerons polarity and elevators operating direction relationship is reversed; check the correction direction by swash plate operation. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "SWH.MIX" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â Select the setting item with the Jog key. SWH.MIX ďźPresent conditionďź Helicopter Condition Mixing master direction ďźRateďź Mixing rate SWH.MIX Activating the function 124 12 12 â When not using this function, select INH. Swash mixing â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â Setup of rate ⥠Select the "RATE" item and then adjust the mixing rate by pressing the + key or â key. â Rangeďź-100 âź +100% Defaultďź0% or â When you want to return the set value to the initial value, press the + key and â key simultaneously. â When you are not using a function, set this to INH. â ON/OFF of a function, Setup of rate, and a trim, Jog key is pushed and setting condition can be chosen. Rangeďź NORM, IDL1, IDL2, IDL3, HOLD Helicopter 125 SWH.RING Swash ring (HELICOPTER) â ELE operation â Function This swash mixing function limits swash travel to prevent damage to the switch linkage due to simultaneous aileron and elevator operation. If is effective in 3D aerobatics with a large steering angle. â â Aileron and elevator stick operation is limited to within the circle (swash mixing) in the ďŹgure shown at the right. (When rate is 100%) Method SwashRing 50% 100% AIL operation â Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "SWH.RING" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź SWH.RING â When not using this function, select INH. Activating the function Swash Ring rate â Select the setting item with the Jog key. â Displays the actual aileron and elevator combined travel when the stick is manipulated. â Adjusts the operable range (swash mixing) of the aileron and elevator sticks. Helicopter Swash Ring â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Setup of rate ⥠Select the "RATE" item and then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź50 âź 200% Defaultďź100% â When you want to return the set value to the initial value, press the + key and â key simultaneously. NOTEďźAdjust the swash mixing rate to the largest swash inclination at which the linkage rod does not interfere. 126 OFFSET Trim oďŹset (HELICOPTER) Function If this trim offset function is used, independent trim adjustments can be made during hovering and in the air. This function can offset the ailerons, elevators, and rudder neutral position by linking to the set switch or condition. A habit that tends to appear from the standpoint of helicopter characteristics when flying at high speed is possible. This function can correct this habit. Ĺ)RUDFORFNZLVHURWDWLRQURWRUVLQFHWKHKHOLFRSWHU WLOWVWRWKHULJKWGXULQJĂLJKWXVHWKHRIIVHWIXQFWLRQ WR VHW WKH VZDVK SODWH VR WKDW WKH KHOLFRSWHU WLOWV WR WKH OHIW 6LQFH WKH GLUHFWLRQ RI WKH HOHYDWRUV LV GLIIHUHQWGHSHQGLQJRQDGMXVWPHQWRIWKHDLUFUDIW GHFLGHWKHVHWWLQJGLUHFWLRQDIWHUĂLJKW:KHQWKH J\URLVXVHGLQWKH$9&6PRGHDWWKHUXGGHUHWF WKHRIIVHWUDWHLVPDGH LQLWLDOVHWWLQJ WRPDNH FRUUHFWLRQVDWWKHJ\URVLGH Ĺ:KHQWKHVZLWFKZDVVHOHFWHGRIIVHWV\VWHPFDQ EHVHWIRUDSRVLWLRQVZLWFKDQGRIIVHWV\VWHPV FDQ EH VHW IRU D SRVLWLRQ VZLWFK /LQNLQJ WR FRQGLWLRQV ,'/ âź +2/' LVDOVRSRVVLEOH Ĺ:KHQWKHRIIVHWIXQFWLRQLVRQGDWDDGMXVWPHQWLV SRVVLEOHHYHQE\GLJLWDOWULP7KHWULPDGMXVWHGUDWH LVLQSXWLQWKHDLU :KHQWKHRIIVHWIXQFWLRQLV21 WKHLQLWLDOVFUHHQWULPGLVSOD\LVOLQNHG Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "OFFSET" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â Select the setting item with the Jog key. â When not using this Function select INH. The display of On/OďŹ is shown when active and assigned to a switch. OFFSET Activating the function Switch direction, Selection of condition OďŹset rate ďźPresent condition ďź Switch selection Trim oďŹset â Activating the function â Select the "MIX" item and t h e n s e l e c t t h e "ON" or "OFF" by pressing the + key or â key. ďź â Switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â or â When you do not use a function, set to the "INH" side. â Switch direction and condition selection ⢠Select the switch direction and condition you want to set at the switch direction and ďź â condition items. or ďź â Helicopter â When "Cond" is chosen, if Jog key is pushed for 1 second, it will change to each condition setting screen. or RangeďźCond, SwA âź SwH â OďŹset rate ⣠Select the "RATE" item and then adjust the oďŹset rate by pressing the + key or â key. Rangeďź-120 âź +120% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. 127 DELAY Delay (HELICOPTER) Function This function prevents sudden offset changes ZKHQWKHRIIVHWSLWFKÄşUXGGHUPL[LQJDQGWKURWWOH hold functions are turned on and off. Ĺ'HOD\FDQEHVHWDWWKHDLOHURQVHOHYDWRUVUXGGHU WKURWWOHDQGSLWFK Ĺ 7 K H V H W G H O D \ L V F R P P R Q W R W K H R I I V H W SLWFKĹUXGGHUPL[LQJDQGWKURWWOHKROGIXQFWLRQV Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "DELAY" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â Select the setting item with the Jog key. DELAY â Linked to the offset, revolution mixing, and throttle hold functions and turned "ON". Delay rate â The delay is maximum at 100%. Delay rate Helicopter â Delay rate setup â Select the "RATE" item and then adjust the delay rate by pressing the + key or â key. ďź â or Rangeďź0 âź 100% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. 128 THR.CUT Throttle cut (HELICOPTER) Function This function cuts (stops) the engine or motor by stick operation. At throttle operation, the rate is adjusted to the position which completely cuts the throttle servo or ESC when the throttle is operated. At function operation, this position is held regardless of the throttle stick position. Ĺ125(6& RSHUDWLRQ PRGH VZLWFKLQJ )RU PRWRU DLUFUDIWVHOHFW(6&)RUPRWRUDLUFUDIWWKHWKURWWOH SRVLWLRQ ZKHQ WKH IXQFWLRQ LV UHVHW FDQ EH VHW VR WKHPRWRUZLOOQRWXQH[SHFWHGO\UXQDWKLJKVSHHG ZKHQ WKH WKURWWOH FXW IXQFWLRQ LV UHVHW :KHQ WKH WKURWWOHVWLFNLVKLJKHUWKDQWKHVHWWKURWWOHSRVLWLRQ WKH WKURWWOH FXW IXQFWLRQ LV QRW UHVHW HYHQ LI WKH VZLWFKLVVHWWR2))6HWWRDVDIHWKURWWOHSRVLWLRQ VORZVLGH Ĺ)XQFWLRQRSHUDWLRQFDQEHVHOHFWHGIURPDPRQJ VZLWFKHV$ âź + Ĺ6HWWKHWKURWWOHFXWIXQFWLRQIRUVDIHW\DOVR Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR.CUT" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź THR.CUT â Select the setting item with the Jog key. â Adjusts the rate to the position that completely cuts the throttle servo or ESC. â Sets the ON/OFF direction of the selected switch. â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN â The "THR" item can be set when the operation mode is "ESC". The number in parentheses is the current throttle stick position. Helicopter Mode Activating the function Cut Position rate Throttle Position Switch selection Switch direction â When not using this Function select INH. The display of On/ Off is shown when active and assigned to a switch. 129 Throttle Cut â Mode â Select the "MODE" item and then select the mode by pressing the + key or â key. ďź â Activating the function ⥠Select the "MIX" item and then select the oďŹ by pressing the + key or â key. â ďź â or or RangeďźNOR, ESC DefaultďźNOR â When you do not use a function, set to the "INH" side. â "NOR"ďźEngine plane "ESC"ďźElectric motor plane â Switch selection ⢠Select the "SW" item and then select the switch by pressing the + key or â key. ďź â â Switch direction ⣠Select the "POSI" by pressing the + key or â key at the ON direction selection item. ďź â or or Rangeďź RangeďźSwA âź SwH DefaultďźSwA â Cut Position rate ⤠Select the "RATE" item and then select the cht position by pressing the + key or â key (motor stop). ďź â ďźIn the case of ESC ďź â Function release Throttle Position ⼠Select the "THR" item and then select the release position by THR stick is lowered and Jog key is pressed for 1 second. Helicopter or â It adjusts to the position where an engine is cut. Rangeďź-30 âź 0 âź +30% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. 130 â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN â Set to a safe low throttle position. Rangeďź0 âź 100% Defaultďź15% GYRO SENS Gyro mixing (HELICOPTER) ďźFor helicopters Gyro mixingďź Function Ĺ:KHQWKH*<PRGHZDVVHOHFWHG$9&RU125 LVGLVSOD\HGDWWKHVHQVLWLYLW\VHWWLQJYDOXH Ĺ7KH VHQVLWLYLW\ VHWWLQJ FKDQQHO FDQ EH VHOHFWHG IURP WKH 58' &+ 58'$,/ &+&+ 58' (/( &+&+ RU 58'$,/(/( &+&+&+ FRPELQDWLRQV This mixing adjusts the gyro sensitivity from the transmitter. The AVCS gyro (GY mode) or normal gyro (STD mode) can be selected. Up to 3 axes can be set. Ĺ7KHVHQVLWLYLW\FDQEHOLQNHGWRWKHFRQGLWLRQ &RQG RUDQDUELWUDU\VZLWFKDQGVHW Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "GYRO SENS" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Activating the function Gain channel selection Switch direction â When not using this function, select INH. GYRO SENS Gain switch direction ďźPresent switch positionďź Gyro type, Gain rate â Select the setting item with the Jog key. ďźGyro typeďź ďźGyro Gain setďź â Swit c h e s t o t h e sensitivity setting screen of each switch direction when the Jog key is pressed. â When a Futaba GY gyro is used, gyro type "GY" is selected. This switches the gyro sensitivity setting item to the mode and sensitivity direct reading display. â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â Gain switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â or â When you do not use a function, set to the "INH" side. â Gain channel selection ⢠Select the ďź â "CH" item and or then select the sensitivity setting channel by pressing the + key or â key. RangeďźRUD, RUD/AIL, RUD/ELE, RUD/AIL/ELE DefaultďźRUD ďź â or Helicopter Gyro setup RangeďźCond, SwA âź SwH â Gyro type and sensitivity setting ⣠Press the Jog key and select the sensitivity setting screen you want to set and then set "type" (gyro type) and "rate" (gyro sensitivity) of each channel by pressing the +key or â key. ďź"type"ďźRangeďźSTD,GY DefaultďźSTD ďź"rate"ďźRangeďź0 âź 100%ďźSTDďź, NOR100 âź 0 âź AVC100% ďźGYďź Defaultďź50% ďźSTDďź, 0% ďźGYďź â When you want to return the set value to the initial value, press the + key and â key simultaneously. 131 D/R,EXPO Dual rate ďź EXPO (HELICOPTER) Function D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps Ĺ7KHFRQWUROVXUIDFHDQJOHLVDGMXVWHGE\HDFKGLUHFWLRQRIWKHVZLWFKRUFRQGLWLRQ7KHOHIWDQG ULJKW XSDQGGRZQ GLUHFWLRQRIHDFKVZLWFKFDQEHVHWLQGLYLGXDOO\ EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle. Ĺ7KHVLGHPDNHVVHUYRPRYHPHQWVOXJJLVKDQGWKHVLGHPDNHVVHUYRPRYHPHQWVHQVLWLYHQHDUWKH QHXWUDOSRVLWLRQ([SRQHQWLDOLVDSSOLHGWRHQWLUHWKURWWOHVHUYRWUDYHO:KHQWKHVLGHLVLQFUHDVHGWKH VORZVLGHEHFRPHVVOXJJLVKDQGWKHKLJKVLGHEHFRPHVVHQVLWLYH Ĺ6HWWLQJFRUUHVSRQGLQJWRHDFKUDWHRIGXDOUDWH '5 LVSRVVLEOH ([FHSWWKURWWOH 7KHGLUHFWLRQRIHDFK VZLWFKDQGWKHOHIWDQGULJKW XSDQGGRZQ GLUHFWLRQRIHDFKFKDQQHOFDQEHVHWLQGLYLGXDOO\ Switch selectionďźSWďź Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate (exponential) switch. Ĺ6HOHFWďź6ZLWFK âź 6ZLWFK+ ďź FRQGLWLRQďź&RQG Ĺ'HIDXOWďź$LOHURQďź6ZLWFK' ďź (OHYDWRUďź6ZLWFK$ ďź 5XGGHUďź6ZLWFK% Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "D/R,EXPO" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Helicopter â The channel under selection is underlined. Channel selection Switch direction ďźpresent switch position ďź Dual rate EXPO â The dual rate and exponential settings are displayed by a curve. Switch selection â Channel selection/Select the setting item with the Jog key. â Jog key is pushed for 1 second, a condition screen will change. 132 ďźSwitch numberďź ďźRateďź ďź Channel ďź 1ďźAileron 2ďźElevator 4ďźRudder Dual rate â Channel selection â A channel is chosen by Jog key. â Switch direction ⥠Select the "No" item and then select the switch direction or condition by pressing the + key or â key. ďź Rangeďź1, 2, 4 â D/R Setup of rate ⢠Select each function item of "D/R" and set the rate by pressing the + key or â key. ďź â or â or Rangeďź0 âź 140% Defaultďź100% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step â Moving to another setting item of the same channel is possible by Jog key. EXPO â Channel selection â A channel is chosen by Jog key. â Switch direction ⥠Select the "No" item and then select the switch direction or condition by pressing the + key or â key. Rangeďź1, 2, 4 ďź â EXP Setup of rate ⢠Select the "EXP" item and then adjust the rate by pressing the + key or â key. ďź â or â Rangeďź-100 âź +100%ăDefaultďź0% or â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step Switch Change â Channel selection â Select the "SW" item and then select the channel with the Jog key. â Switch selection ⥠A switch or Cond is chosen by + key or â key. ďź Helicopter â Moving to another setting item of the same channel is possible by Jog key. â or Rangeďź1, 2, 4 RangeďźSwA âź SwH, Cond â When "Cond" is chosen, a setup is possible for every condition. 133 THR-CURVE Throttle curveďźFor helicopters ďź (HELICOPTER) Function The throttle curve function sets a 5 point curve in relation to the throttle stick movement and adjusts each point over the 0 âź 100% range so that the HQJLQHVSHHGLVRSWLPXPIRUĂLJKW Ĺ1RUPDO 125 LGOHXS ,'/ LGOHXS ,'/ DQG LGOHXS ,'/ WKURWWOHFXUYHVFDQEHVHW Ĺ7KHQRUPDO 125 LGOHXS ,'/ LGOHXS ,'/ DQGLGOHXS ,'/ VZLWFKFDQEHSUHVHWDWWKH FRQGLWLRQVHOHFWLRQVFUHHQ ďźNormal throttle curve adjustment methodďź The normal throttle curve creates a basic throttle curve centered near hovering. This curve is adjusted together with the normal pitch curve so that engine speed is constant and up/down control is easiest. The normal throttle function is always on. ďźIdle up 1/2/3 throttle curve adjustment methodďź The idle up curves are set so that the engine maintains a constant speed even when the pitch is reduced during ďŹight. Curves matched to the purpose such as loop, roll and 3D are created and idle up curves 1/2/3 are by aerobatics. CAUTIONS ďźťOperation precautionsďź˝When starting the engine, always set idle up sticks 1/2/3 to OFF and start the engine at idling. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR-CURVE" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Helicopter Activating the function Setting condition â When not using this Function select INH. The display of On/ Off is shown when active and assigned to a switch. A display when normal is "---" ďźalwaysONďź THR-CURVE 5point curve rate â The THR-CURVE settings are displayed by a curve. â Select the setting item with the Jog key. ďźRateďź ďźPresent conditionďź 134 Throttle curve â Activating the throttle curves (ID1/2/3) â Select the "MIX" item and set to ďź "ON" or "OFF" by pressing the + key or â key. â or â For the normal condition, "---" is displayed. (Always ON) RangeďźNOR, ID1, ID2, ID3 â When you do not want to use an idle up curve, set to "INH". â 5 point curve setting ⥠Select the setting item of each point (P-1 âź P-5) with the Jog key and set the travel of each point by pressing the + key or â key. ďź â Defaultďź P-5: 100% P-4: 75% P-3: 50% P-2: 25% P-1: 0% Rangeďź0 âź 100% or â When you want to return the set value to the initial value, press the + key and â key simultaneously. â Curve copying method â Select the "CND" item and switch to the curve copy mode by pressing the Jog key. ⥠Press the + key or â key and select the copy destination condition. ďź â˘ Copy the condition by pressing the Jog key for 1 second. â ďź1 secondďź or â Throttle curve setting examples ďźThe example of a setting ďź RATE RATE 50 25 P1 75 50 P3 P4 STICK ďźNormalďź P5 P1 P5=100.0% P4= 75.0% P3= 65.0% P2= 65.0% P1= 67.0% 75 50 25 25 P2 ďźThe example of a setting ďź 100 P5=100.0% P4= 75.0% P3= 50.0% P2= 54.0% P1= 56.0% P2 P3 P4 P5 P1 P2 STICK ďźIdle-up1ďź P3 P4 P5 Helicopter 75 ďźThe example of a setting ďź 100 P5=100.0% P4= 65.0% P3= 50.0% P2= 30.0% P1= 0.0% RATE 100 STICK ďźIdle-up2ďź NOTEďźSet the actual value of the throttle curve according to the fuselage speciďŹcations. 135 PIT-CURVE Pitch curveďźFor helicopters ďź (HELICOPTER) Function The pitch curve function allows setting by a 5 point curve in relation to throttle stick movement and adjustment of each point over the -100% âź +100% range so that the pitch enters the optimum ĂLJKWVWDWH Ĺ1RUPDO 125 LGOHXS ,'/ LGOHXS ,'/ LGOH XS ,'/ DQG KROG +/' SLWFK FXUYHV FDQ EH VHW Ĺ7KHQRUPDO 125 LGOHXS ,'/ LGOHXS ,'/ LGOHXS '/ DQGKROG +2/' VZLWFKHVFDQEH SUHVHWDWWKHFRQGLWLRQVVHOHFWLRQVFUHHQ NOTEďźWhen the hold switch is on, the hold function has priority even though an idle up switch is in any position. ďźNormal curve adjustment methodďź The normal pitch curve creates a basic pitch curve centered near hovering. This curve is adjusted together with the throttle pitch curve so that engine speed is constant and up/down control is easiest. ďźIdle up 1/2/3 curve adjustment methodďź The high side pitch curve sets the maximum pitch that does not apply a load to the engine. The low side pitch curve is created to match the purpose such as loop, roll, and 3D. The idle up 1/2/3 curves are used by aerobatics. ďźThrottle hold curve adjustment methodďź The throttle hold curve is used when performing auto rotation dives. Set the intermediate pitch to match the stick work at pitch up. Method Calling the setting screen Helicopter â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "PIT-CURVE" from the menu with the Jog key. ďź ďź1 secondďź Activating the function Condition â When not using this Function select INH. The display of On/ OďŹ is shown when active and assigned to a switch. When normal,"---" (always ON) is displayed. PIT-CURVE 5point curve rate â Select the setting item with the Jog key. â The PIT-CURVE settings are displayed by a curve. ďźRateďź ďźPresent conditionďź 136 ⢠Open the setting screen by pressing the Jog key. Pitch curve â Activating the pitch curves ďźID1/2/3, HLDďź â Select the "MIX" item and then ďź select the "ON" or "OFF" by or pressing the + key or â key. â â For the normal condition, "---" is displayed. (Always ON) RangeďźNOR, ID1, ID2, ID3, HLD â When you do not want to use an idle up, hold curve, set to "INH". Defaultďź P-5: +100% P-4: +50% P-3: 0% P-2: -50% P-1: -100% â 5 point curve setting ⥠Select the setting item of each point (P-1 âź P-5) with the Jog key and set the travel of each point by pressing the + key or â key. ďź â Rangeďź-100 âź +100% or â When you want to return the set value to the initial value, press the + key and â key simultaneously. â Curve copying method â Select the "CND" item and switch to the curve copy mode by pressing the Jog key. ⥠Press the + key or â key and select the copy destination condition. ďź â˘ Copy the condition by pressing the Jog key for 1 second. â ďź1 secondďź or â Pitch curve setting examples -50 -100 P1 P2 P3 P4 P5 STICK ďźNormalďź +50 RATE P5= +40% P4= +10% P3= -10% P2= -40% P1= -70% +50 -50 -100 P1 -100 P1 P2 P3 STICK P4 P5 P5= +40% P4= +10% P3= -10% P2= -50% P1= -80% -50 ďźIdle-up1ďź ďźThe example of a setting ďź +100 +50 RATE P5= +70% P4= +50% P3= +6% P2= -40% P1= -70% ďźThe example of a setting ďź +100 P2 P3 P4 P5 STICK Helicopter RATE +50 ďźThe example of a setting ďź +100 RATE ďźThe example of a setting ďź +100 ďźIdle-up2ďź NOTEďźSet the actual value of the pitch curve according to the fuselage speciďŹcations. P5= +100% P4= +50% P3= 0% P2= -50% P1= -100% -50 -100 P1 P2 P3 STICK P4 P5 ďźHoldďź 137 REVO.MIX Pitch â Rudder mixing (HELICOPTER) Function 7KH SLWFKÄşUXGGHU PL[LQJ IXQFWLRQ FRQWUROV the pitch of the tail rotor to suppress the reaction torque (force that attempts to swing the helicopter in the direction opposite the direction of rotation of the main rotor) generated by the main rotor pitch and speed. It is adjusted so that the pitch of the tail rotor is also changed when the main rotor pitch changes and reaction torque appears and so that the nose does not swing to the left and right. However, when the AVCS mode is used with a GY 6HULHVJ\URSLWFKÄşUXGGHUPL[LQJLVXQQHFHVVDU\ Ĺ7KHQRUPDO 125 LGOHXS ,'/ DQGLGOHXS ,'/ UDWHVFDQEHVHW Ĺ7KHKLJKVLGHDQGORZVLGHUDWHVFDQEHDGMXVWHG Ĺ)RU D FORFNZLVH URWDWLRQ URWRU WKH RSHUDWLQJ GLUHFWLRQ LV VHW VR WKDW WKH UXGGHU LV PL[HG LQ WKH ULJKW GLUHFWLRQ ZKHQ WKH SLWFK EHFRPHV SOXV )RU D FRXQWHUFORFNZLVH URWDWLRQ URWRU WKH VHWWLQJ LV RSSRVLWH 7KH RSHUDWLQJ GLUHFWLRQ VHWWLQJ UHYHUVHV WKHUDWHSRODULW\ &:URWDWLRQ/RZVLGH /2: KLJKVLGH +,*+ &&: URWDWLRQ /RZ VLGH /2: KLJK VLGH +,*+ *7KH DERYH YDOXHV DUH WKH LQLWLDO YDOXHV 5HSODFH WKHPZLWKWKHDFWXDOVHWWLQJYDOXHV Adjustment procedure First, trim at hovering and then adjust the neutral position. ďźNormal pitch â rudder mixingďź Helicopter â Throttle low side (slow while hovering) adjustment Repeatedly hover from take oďŹ and land from hovering at a constant rate matched to your own rhythm, and adjust pitch â rudder mixing so that the nose does not deďŹect when the throttle is raised and lowered. If the nose points to the left when landing from hovering or points to the right when taking oďŹ, when hovering stabilizes and the stick moves to the neutral position, low side mixing rate is probably too large and when the nose points in the opposite direction, low side rate is probably too small. However, when landing, the direction of the nose may not stabilize depending on the state on the ground. The direction of the nose may also become unstable when rotation of the rotor does not rise. â Throttle high (up to climbing from hovering and diving hovering) adjustment Repeat up to climbing from hovering and diving hovering matched to your own rhythm and adjust pitch â rudder mixing so that the nose does not deďŹect to the left and right when the throttle is raised and lowered. If the nose points to the right when climbing from hovering, the high side mixing rate is too large and if the nose points to the right, the mixing rate is too small. Repeat climbing and diving and make adjustment while taking the balance. ďźidle-up1/2,3Pitch â Ruddermixingďź This mixing sets the mixing rate so that the rudder direction is straight forward at high speed ďŹight. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ďź ďź1 secondďź 138 ⥠Select "REVO.MIX" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. Activating the function Selection of condition High side Setup of rate Low side Setup of rate REVO.MIX â When not using this function, select INH. ďźpresent switch position ďź â Select the setting item with the Jog key. ďźRateďź Pitch â Ruddermixing â Activating the function â Select the "MIX" ďź item and then select the "ON" by pressing the + key or â key. â Selection of condition ⥠Select the "CND" item and selection of condition by pressing the + key or â key. â or â or RangeďźNORM, IDL1/2, IDL3 â When you do not use a function, set to the "INH" side. â Setup of rate ⢠Select each function item of "HI"or "LO" and set the rate by pressing the + key or â key. ďź ďź â or Rangeďź-100 âź +100% Default(NORM)ďź-20%(LOW)ă+20%(HIGH) Default(IDL1/2/3)ďź0%(LOW)ă0%(HIGH) â When you want to return the set value to the initial value, press the + key and â key simultaneously. Helicopter 139 THR HOLD Throttle hold (HELICOPTER) Function The throttle hold function fixes or stops the engine throttle position by hold switch operation during an auto rotation dive. Operation can be set within the -50% âź +50% range based on the throttle trim position. The switch is changed at the conditions selection screen. (Initial setting: SwG) CAUTIONS ďźťNOTEďź˝Priority is given to throttlehold over idle-up. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR HOLD" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź THR HOLD Activating the function â When not using this Function select INH. The display of On/ Off is shown when active and assigned to a switch. hold throttle position â Select the setting item with the Jog key. Throttle hold Helicopter â Activating the function â Select the "MIX" item and then select the "ON" or "OFF" by pressing the + key or â key. ďź â or â Hold throttle position ⥠Select the "RATE" item and then adjust the rate by pressing the + key or â key. ďź â or Rangeďź-50 âź +50% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. â When you do not use a function, set to the "INH" side. â Function ACT â INH is linked to ăHold position adjustment methodă condition THR-HOLD, and can be set â When you want to lower the engine idling, set to the "+" direction and at any screen. adjust so that the carburetor is full open. â When maintaining idling, set the throttle stick to the slow position and turn the hold switch on and oďŹ and set to the number at which the servo does not operate. NOTEďźWhen connecting the throttle linkage, lower the digital trim to the slowest and adjust so that the carburetor is full open. 140 GOVERNOR Governor mixing (HELICOPTER) Function When a governor (CGY750/GY701/GV-1, etc.) is used, the speed can be adjusted from the transmitter. CH7 or CH8 can be selected as the speed setting control channel. When using a separate ON/OFF switch (cut switch), ON/OFF control uses CH8. In this case, CH7 controls speed setting. Setting examplesďź â Example of setting that switches the speed and ON/OFF by 3 position switch 3position Adjustment from transmitter Switch Setup of rate direction R.P.M 1ďźOFF UP 0% 0%ďźGovernor R.P.M "oďŹ"ďź R.P.M 2ďź1400 CNTR 50% "50%" R.P.M 3ďź1700 DOWN 100% "100%" *For example, speed 3 sets *For the time being use the *Since speed adjustment from the transmitter the maximum speed to be initial rate setting. is rate setting, checking the actual speed at used and is lowered and the governor display and remembering its adjusted at the transmitter. relationship is convenient. Governor speed ďźsetting exampleďź â Switching the speed for each condition The speed for each condition can be set by selecting "Cond" by switch. Since speed adjustment from the transmitter is rate setting, for the actual speed check the governor display. â Controlling governor ON/OFF by separate switch When a separate switch is used to turn the governor on and oďŹ, switch setting is performed by "OFF-CNTRL" item. *Speed and ON/OFF switch settings are different depending on the governor. Perform these settings in accordance with the instruction manual of the governor used. *At throttle hold, always conďŹrm that the governor is OFF. Conversely, when raising the speed value, reverse the polarity of "CH8". Method Calling the setting screen ⥠Select "GOVERNOR" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When "INH", the function cannot be used. When you want to use CH7 as the speed setting channel, select "CH7" and when you want to use CH8(9), select "CH8(9)". GOVERNOR Activating the function Switch selection Setup of rate â Select the setting item with the Jog key. Helicopter â Call the menu screen from the home screen by pressing the + key for 1 second. ďźRateďź â The above screen shows the case when the speed is set for each condition. 141 Governor mixing â A c t i v a t i n g t h e f u n c t i o nďźR . P. M C H selectionďź â Select the "MIX" item ďź â and then select the or "CH7""CH8" or "CH9" by pressing the + key or â key. â Switch selection ⥠Select the "MODE" item and then select the switch by pressing the + key or â key. ďź â or RangeďźCond, SwA âź SwH â When you do not use a function, set to the "INH" side. â R.P.M setting ⢠Select the "RATE" item and then adjust the rate by pressing the + key or â key. ďź Rangeďź0.0 âź 100.0% â or Defaultďź ďźCondďź NORM=0.0%, IDL1=50.0%, IDL2=100.0%, IDL3=100.0%, HOLD=0.0% ďź2P Switch selection ďź UP=0.0%, DOWN=100.0% ďź3P Switch selectionďź UP=0.0%, CNTR=50.0%, DOWN=100.0% ďźWhen using an ON/OFF switchďź *Select the OFF-CTRL item and then adjust the rate by pressing the + key or â key. â ON/OFF Switch selection â Switch direction â Select the "SW" ďź âĄ Select the "POSI" by pressing ďź â or item and then the + key or â key at the ON or select the switch direction selection item. by pressing the â 2P SWďźUP, DOWN + key or â key. â 3P SWďźUP, UP&D, UP&C, CNTR, C&DN, DOWN â RangeďźSwA âź SwH DefaultďźSwA Helicopter ďźWhen number of rotations goes up at the time of Throttlehold ďź *If the speed is increased at throttle hold, the governor and transmitter operating directions will not coincide. In this case, match the operating directions by reversing the polarity of "CH8". What is a governor ďź A governor is made up of a set of sensors which read the RPM of the helicopter s head, and a control unit that automatically adjusts the throttle setting to maintain a constant head speed regardless of changes in pitch of blades, weather conditions, etc. Governors are extremely popular in competition helicopters due to the consistency provided. How does it help in helicopter setup? The governor eliminates the need to spend large amounts of time setting up throttle curves, as it automatically adjusts the engine s RPM to maintain the desired head speed. 142 HOV-THR Hovering throttle (HELICOPTER) Function The hovering throttle function trims the throttle near the hovering point. When the hovering throttle knob is turned clockwise, the speed increases and when it is turned counterclockwise, the speed decreases. Rotor speed changes due to changes in the temperature, humidity, and other flying conditions can be trimmed. Adjust for the most stable rotor speed. More precise trimming is possible by using this function together with the hovering pitch function. Ĺ7KHRSHUDWLRQFRQGLWLRQFDQEHVHOHFWHGIURPRQO\ QRUPDORUQRUPDOLGOHXS Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "HOV-THR" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Activating the function â When "INH", the function cannot be used. To use the function, switch to "ON". HOV-THR Trim memory settting ďźCompensation amount at trim memoryďź VR setting Selection of condition ďźActual compensation amount including the hovering throttle knobďź â Select the setting item with the Jog key. â NORMďźOnly the normal condition operates â NORM/IDL1ďźIt operates by normal condition and idle-up1. â The knob operating direction is diďŹerent depending on the polarity. Hovering Throttle â or â When you do not use a function, set to the "INH" side. â VR setting ⢠Select the "VR" item and then select the "VR" or "DT" by pressing the + key or â key. RangeďźNULLďźOFFďź, +VR, -VR, +DT5, -DT5, +DT6, -DT6 Defaultďź+DT6 â Selection of condition ⥠Select the "MODE" item and then select condition by pressing the + key or â key. ďź â or RangeďźNORM, NORM/IDL1 DefaultďźNORM Helicopter â Activating the function â Select the "MIX" ďź item and then select the "ON" by pressing the + key or â key. ďźMemorizing the hovering throttle adjustment positionďź â Memory setting ⣠Select the "RATE" item and memorize the current trim position by pressing the Jog key. â When the knob is returned to the center after memorization, the trim position returns to its previous position. ďźťNOTEďź˝If memorization is repeated at the same position, the value is cumulated. 143 HOV-PIT Hovering pitch (HELICOPTER) Function The hovering pitch function trims the pitch near the hovering point. When the hovering pitch knob is turned clockwise, the pitch gets stronger and when it is turned counterclockwise, the pitch gets weaker. Rotor speed changes due to changes in temperature, humidity, and other flying conditions can be trimmed. Adjust for the most stable rotor rotation. Method More precise trimming is possible by using this function together with the hovering throttle function. Ĺ7KH RSHUDWLQJ FRQGLWLRQ FDQ EH VHOHFWHG IURP QRUPDORQO\DQGQRUPDOLGOHXS Ĺ7KH WULP SRVLWLRQ FDQ EH PHPRUL]HG ,I LW LV PHPRUL]HGEHIRUHWKHPRGHOPHPRU\LVFKDQJHG WKHRULJLQDOWULPVWDWHFDQEHUHWULHYHGE\PHUHO\ VHWWLQJ WKH NQRE WR WKH FHQWHU ZKHQ WKH WULP SRVLWLRQLVUHFDOOHG Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "HOV-PIT" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When "INH", the function cannot be used. To use the function, switch to "ON". HOV-PIT Activating the function Trim memory settting ďźCompensation amount at trim memoryďź VR setting Selection of condition ďźActual compensation amount including the hovering pitch knobďź â Select the setting item with the Jog key. â NORMďźOnly the normal condition operates â NORM/IDL1ďźIt operates by normal condition and idle-up1. Helicopter Hovering Pitch â Activating the function â Select the "MIX" ďź item and then select the "ON" by pressing the + key or â key. â or â When you do not use a function, set to the "INH" side. â VR setting ⢠Select the "VR" item and then select the "VR" or "DT" by pressing the + key or â key. ďź â or RangeďźNULLďźOFFďź, +VR, -VR, +DT5, -DT5, +DT6, -DT6 Defaultďź-VR 144 â The knob operating direction is diďŹerent depending on the polarity â Selection of condition ⥠Select the "MODE" item and then select condition by pressing the + key or â key. ďź â or RangeďźNORM, NORM/IDL1 DefaultďźNORM ďźMemorizing the hovering pitch adjustment positionďź â Memory setting ⣠Select the "RATE" item and memorize the current trim position by pressing the Jog key. â When the knob is returned to the center after memorization, the trim position returns to its previous position. ďźťNOTEďź˝If memorization is repeated at the same position, the value is cumulated. HI/LO-PIT HI/LO-pitch trim (HELICOPTER) Function The high/low pitch trim function adjusts the pitch servo high side and low side to the optimum SLWFKLQGLYLGXDOO\IRUHDFKĂLJKWFRQGLWLRQ QRUPDO idle up 1/2/3, hold). Ĺ7KH KLJK SLWFK DQG ORZ SLWFK WULP OHYHUV DQG RSHUDWLQJ GLUHFWLRQ FDQ EH VHOHFWHG 7KH WULP OHYHUVRSHUDWHLQFRPPRQIRUHDFKFRQGLWLRQDQG D XVHGR QRW XVH WULP OHYHU FDQ EH VHOHFWHG IRU HDFKIXQFWLRQ Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "HI/LO-PIT" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Selection of condition HI/LO-PIT High side Pitch Trim ON,OFF High side trim ďźPresent condition ďź ďźActual adjustment position including high pitch trimďź ďźLow side sameďź â Selected from among DT5, DT6, and VR. The operation direction is different depending on the polarity (+, -). â Select the setting item with the Jog key. HI/LO-pitch trim â or â Adjustment by Key operation ⣠Select each function item of "HI-PIT" or "LO-PIT" and set the pitch rate by pressing the + key or â key. Rangeďź60 âź 100% Defaultďź100% Helicopter â Selection of condition â Select the setting ďź condition selection item and select the condition by pressing the + key or â key. â DT, VR adjustment ON, OFF selection ⥠Select ON, OFF by pressing the + key or â key at the high side or low side "ADJ" item. â TYP selection ⢠Select trim or VR by pressing the + key or â key at the "TYP" item. Rangeďź+DT5, -DT5, +DT6, -DT6,+VR, -VR â The high side or low side pitch can be adjusted with the selected digital trim or VR. 145 THR-MIX Throttle mixing (HELICOPTER) Function This mixing compensates for slowing of the helicopter when the ailerons, elevators, and rudder are operated. Ĺ7KHFRUUHFWLRQDPRXQWOLPLWVWKHWKURWWOHKROGSRLQW RUKLJKHVWSRLQW RSHUDWLRQ Ĺ7KH FRPSHQVDWLRQ DPRXQW FDQ EH VHW IRU HDFK FRQGLWLRQ Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR-MIX" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź THR-MIX â When not using this function, select INH. Activating the function Condition ďźPresent conditionďź Mixing â Select the setting item with the Jog key. ďźRateďź Helicopter Throttle mixing â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Setup of rate ⥠Select each function item of "MIX" and set the rate by pressing the + key or â key. ďź â or Rangeďź0 âź 100% ďźRUD â THR : -100 âź +100%ďź Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. â The setting condition can be selected by pressing the Jog key at rate adjustment. RangeďźNORM, IDL1, IDL2, IDL3 146 THR â NEEDL Throttle â NeedlemixingďźFor helicopters ďź (HELICOPTER) Function This mixing sets the mixture by a 5 point curve in relation to throttle stick movement when the engine is equipped with a mixture control system (needle control or other mixture adjustment). Normal condition (NOR) idle up use (ID2) and idle up 3 (ID3) can be set independently. The needle servo connects to CH8 of the transmitter. 8CH Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "THR â NEEDL" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When not using this function, select INH. 7+5 ⍠ÚâŹ1(('/ Activating the function Condition ďźPresent conditionďź 5 point curve set â The CURVE settings are displayed by a curve. â Select the setting item with the Jog key. Throttle â Needlemixing â Activating the function â Select the "MIX" item and then select the "ON" or "OFF" by pressing the + key or â key. ďź â â When such, setting condition can be chosen by pressing Jog key. or RangeďźNOR, I12, ID3 â 5 point curve setting ⥠Select the setting item of each point (P-1 âź P-5) with the Jog key and set the travel of each point by pressing the + key or â key. ďź Helicopter â When you do not use a function, set to the "INH" side. Defaultďź P-5: 100.0% P-4: 75.0% P-3: 50.0% P-2: 25.0% P-1: 0.0% â or â When you want to return the set value to the initial value, press the + key and â key simultaneously. Rangeďź0.0 âź 100.0% â Curve copying method â Select the "CND" item and switch to the curve copy mode by pressing the Jog key. ⥠Press the + key or â key and select the copy destination condition. ďź â ⢠Copy the condition by pressing the Jog key for 1 second. ďź1 secondďź or 147 Glider function The setting screen of each function is called from the following menu. The function when the model type was set to glider (2AIL+4FLP) is displayed here. Power ON â First set the throttle to slow. â Then turn on the power. â W hen t h e E N D k e y i s pressed, the display returns to the home screen. To menu screen by holding down the + key ďźHome screenďź AF4 ďź END ďź1 secondďź â When the + key is pressed for 1 second, the menu screen is displayed. MENU 0(18ĺ˛ĺ˛ĺ˛ĺ˛$)1 0(18ĺ˛ĺ˛ĺ˛ĺ˛$) 1 MENU 1/3 ăŁ0'/6(/ ăŁ0'/1$0( ăŁ)$,/6$)( ăŁ5(9(56( ăŁ7,0(5 ăŁ6(592 ăŁ(1'32,17 ăŁ75,0 ăŁ68%75,0 ăŁ30,; ăŁ$8;&+$1 ăŁ3$5$0(7(5 0(18ĺ˛ĺ˛ĺ˛ĺ˛$)12 Glider MENU 2/3 ăŁ7(/(0(75< ăŁ6(1625 ăŁ6%86/,1. ăŁ0'/75$16 ăŁ75$,1(5 ăŁ$,/',)) ăŁ$,/âŤÚâŹ58' ăŁ97$,/ ăŁ*<526(16 0(18ĺ˛ĺ˛ĺ˛ĺ˛$)123 MENU 3/3 148 ăŁ'5(;32 ăŁ02725 ăŁ&21',7,21 ăŁ58'âŤÚâŹ$,/ ăŁ&$0%5ĺ˛)/3 ăŁ&$0%5ĺ˛0,; ăŁ%877(5)/< ăŁ&$0%5âŤ(ÚâŹ/( ăŁ(/(âŤ&ÚâŹ$0%5 ăŁ$,/âŤ&ÚâŹ$0%5 ăŁ$,/âŤÚâŹ%5.)/ ăŁ75,00,; ďźSelectionďź â Move the cursor ( h i g h l i g ht e d ) u p a n d down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. ďźCalling the setting screenďź ĆPress the Jog key to open the setting screen. Key ďź LCD âďź key ââ key AF4 âJog key âEND key â The menu item is an example of WING type 2 ailerons + 4 ďŹaps. The menu items can be changed according to the WING type. For example, if WING type is 1AIL, since the item blinks, reference only the item of the WING type used. Relevant WING type display â WING TYPE 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Refer to "Common Functions" previously described for a description of this function. â Function MENU1/3 MDL-SEL MENU 3/3 MENU2/3 (P.40) TELEMETRY (P.66) D/R, EXPO Model select ďź Model Copy ďź Data reset ďź RX ďź Link Telemetry Display ďź Alarm setup Dual rate ďź EXPO MDL-NAME SENSOR MOTOR SW Telemetry sensor (P.43) Model name ďź User name FAIL SAFE (P.45) Fail safe REVERSE (P.47) Servo reverse TIMER (P.48) Timer SERVO SBUS LINK MDL-TRANS TRIM Trim reset ďź Trim step Sub trim P.MIX1-6 (P.151) BUTTERFLY (P.161) ButterďŹy mixing (P.152) CAMBR â ELE (P.162) Camber â Elevator mixing (P.153) ELE â CAMBR (P.163) Elevator â Camber mixing (P.165) Aileron â Camber mixing (P.166) Aileron â Brake ďŹap TRIM MIX (P.58) (P.160) Camber mixing AIL â BRKFL (P.56) AUX channel PARAMETER CAMBR MIX AIL â CAMBR (P.53) Program mixing 1 âź 6 AUX-CHAN (P.150) V-Tail Gyro mixing (P.159) Camber ďŹap mixing Aileron DiďŹerential GYRO SENS (P.52) (P.93) (P.158) Glider SUB TRIM RUD â AIL CAMBR FLP V-TAIL (P.51) (P.92) Trainer Aileron â Rudder (P.157) Condition TRAINER AIL â RUD End point CONDITION Rudder â Aileron mixing END POINT (P.50) (P.89) Data transfer of another 10J or 8J Servo monitor ďź Servo test (P.156) Motor switch S.BUS servo set up AIL-DIFF (P.49) (P.83) (P.154) (P.167) Trim MIX Data reset ďź Model type ďź ATLtrim ďź LCD contrast ďź Back light : mode, time, adjustment ďź Home display ďź Battery alarm ďź Battery vibration ďź Buzzer tone ďź Jog navi ďź Jog light ďź Jog time ďź Telemetry : mode, unit ďź Speech : language, volume ďź Stick position alarm 149 AIL-DIFF Aileron diďŹerential WING TYPE Function (GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Two servos can be used for ailerons and a differential can be applied to left and right aileron operation. Connect the left aileron to CH1 (AIL) and the right aileron to CH7. CH1 Ĺ7KHXSDQGGRZQDQJOHRIWKHOHIWDQGULJKWDLOHURQ FRQWUROVXUIDFHFDQEHDGMXVWHGLQGLYLGXDOO\ CH7 Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "AIL-DIFF" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź AIL-DIFF ďźAileron rateďź Aileron1ďźCH1ďźrate Aileron2ďźCH7ďźrate â Select the setting item with the Jog key. Aileron DiďŹerential Glider â Aileron control surface angle adjustment â Select the "RATE-AIL1" item and then move the aileron stick to the left and right and adjust the travel of each by pressing the + key or â key. Rangeďź-120 âź +120% Defaultďź+100% â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. ďźAdjust the RATE-AIL2 item the same as ⥠.ďź 150 LďźAileron Stick Left side rate RďźAileron Stick Right side rate AIL â RUD Aileron â Rudder (GLIDER) WING TYPE Function 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Use this mix when you want to mix the rudder with aileron operation. This allows the aircraft to bank at a steep angle. Ĺ:KHQ WKH PL[LQJ GLUHFWLRQ LV UHYHUVHG E\ WKH OLQNDJH DGMXVWPHQWV FDQ EH PDGH E\ FKDQJLQJ WKHUDWHSRODULW\ Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "AIL â RUD" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź ĺ´ĺľĺľĺľâŤÚâŹĺľĺ´¨ĺľ¤ $,/ ⍠ÚâŹ58' â When not using this function, select INH. Activating the function 0,;ăŁINH Rate adjustment 5$7(㣠1250 6:ăŁ6:$ 326,ăŁ'2:1 â Select the setting item with the Jog key. 3 Position Switch NULL ON UP ON UP&DWN ON ON OFF OFF ON 2 Position Switch NULL UP UP&CNT ON ON OFF OFF ON CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF â When condition was used, the display can be switched and each connection can be set by switching the condition switch. â The ON/OFF switch can be changed. (Selected with the Jog key and changed with the +key) â Sets the ON/OFF direction of the selected switch. OFF ON DOWN ON ON OFF ON OFF ON â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â â Mixing rate ⥠S e l e c t t h e " R AT E " i t em a n d then adjust the mixing rate by pressing the + key or â key. ďź â or or Rangeďź-100 âź +100% Defaultďź0% â When you do not use a function, set to the "INH" side. â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. Glider Aileron â Rudder 151 V-TAIL V-Tail (GLIDER) WING TYPE Function 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F This mixing is used with V tail aircraft that combine the elevator and rudder functions. ďźś-tail CH2 (CH4) Elevator Rudder Method CH4 (CH2) CH2 Servo ELE1 RUD2 CH4 Servo ELE2 RUD1 Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "V-TAIL" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Activating the function â When INH is selected, the function cannot be used. To use the function, select ACT. V-TAIL ELE1 rate ELE2 rate ďźRate adjustmentďź RUD2 rate RUD1 rate â Select the setting item with the Jog key. V-TAIL Glider â Activating the function â Select the "MIX" item and then select the "ACT" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Rate adjustment ⥠Select the "RATE" item and then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź-100 âź +100% Defaultďź+50% ďźonly ELE2 : -50%ďź â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. NOTEďźWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and rudder operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. 152 GYRO SENS Gyro sensor (GLIDER) WING TYPE Function 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F IOLJKW WKH J\UR ZLOO ORVH FRQWURO RI WKH SODQH¡V DWWLWXGH )URP WKH VWDQGSRLQW RI VDIHW\ ZH UHFRPPHQGWKDWWKH2)) SRVLWLRQDOVREHVHW XVLQJDSRVLWLRQVZLWFK Ĺ&+ &+&+ &+&+ RU &+&+&+ FRPELQDWLRQV FDQ EH VHOHFWHG DV WKH VHQVLWLYLW\ VHWWLQJFKDQQHO This function is dedicated mixing for switching the gyro sensitivity and gyro mode (AVCS/ NORMAL) of Futaba airplane use gyros. Up to 3 axes can be set. Ĺ7KH VHQVLWLYLW\ VZLWFK FDQ EH VHOHFWHG DQG WKH VHQVLWLYLW\RIHDFKGLUHFWLRQRIWKHVZLWFKFDQEH VHW 6ZLWFKHV $ WR + ,I WKH DLUSODQH VWDOOV GXULQJ Method Calling the setting screen ⥠Select "GYRO SENS" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Activating the function Gain Channel selection Switch direction â When not using this function, select INH. GYRO SENS Sensitivity switch selection ďźC u r r e n t s w i t c h o p e r a t i n g directionďź Gyrotype, Gain rate â Switches to the sensitivity setting screen of each switch direction when the Jog key is pressed. â Select the setting item with the Jog key. GYRO SENS â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďźGyro typeďź ďźGyro Gainďź â When using a Futaba GYA gyro, select gyro type GY. This switches the gyro sensitivity setting item to mode and sensitivity direct reading display. ďź â Sensitivity switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â or ďź RangeďźCH5ăCH5/CH7ă CH5/CH8ăCH5/CH7/CH8 DefaultďźCH5 RangeďźSwA âź SwHăDefaultďźSwA â Gyro type and sensitivity setting ⣠Press the Jog key and select the sensitivity setting screen you want to set and then set "type" (gyro type) and "rate" (gyro sensitivity) of each channel by pressing the + key or â key. ďź"type"ďźRangeďźSTD,GY Glider â When you do not use a function, set to the "INH" side. â Sensitivity setting channel selection ⢠Select the ďź â "CH" item and or then select the sensitivity setting channel by pressing the + key or â key. â or DefaultďźSTD ďź"rate"ďźRangeďź0 âź 100%ďźSTDďź, NOR100 âź 0 âź AVC100% ďźGYďź Defaultďź50%ďźSTDďź, 0% ďźGYďź â When you want to return the set value to the initial value, press the + key and â key simultaneously. 153 D/R,EXPO Dual rate ďź EXPO WING TYPE Function (GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps Ĺ7KHFRQWUROVXUIDFHDQJOHLVDGMXVWHGE\HDFKGLUHFWLRQRIWKHVZLWFK7KHOHIWDQGULJKW XSDQGGRZQ GLUHFWLRQRIHDFKVZLWFKFDQEHVHWLQGLYLGXDOO\ EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle. Ĺ7KHVLGHPDNHVVHUYRPRYHPHQWVOXJJLVKDQGWKHVLGHPDNHVVHUYRPRYHPHQWVHQVLWLYHQHDUWKH QHXWUDOSRVLWLRQ([SRQHQWLDOLVDSSOLHGWRHQWLUHWKURWWOHVHUYRWUDYHO:KHQWKHVLGHLVLQFUHDVHGWKH VORZVLGHEHFRPHVVOXJJLVKDQGWKHKLJKVLGHEHFRPHVVHQVLWLYH Ĺ6HWWLQJFRUUHVSRQGLQJWRHDFKUDWHRIGXDOUDWH '5 LVSRVVLEOH ([FHSWWKURWWOH 7KHGLUHFWLRQRIHDFK VZLWFKDQGWKHOHIWDQGULJKW XSDQGGRZQ GLUHFWLRQRIHDFKFKDQQHOFDQEHVHWLQGLYLGXDOO\ Switch selectionďźSWďź Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate (exponential) switch. Ĺ'HIDXOWďź$LOHURQďź6ZLWFK' ďź (OHYDWRUďź6ZLWFK$ ďź 5XGGHUďź6ZLWFK% Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "D/R, EXPO" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Glider â The channel under selection is underlined. Channel selection Dual rate ďźSwitch Directionďź EXPO â The dual rate and exponential settings are displayed by a curve. Switch selection â Channel selection/Select the setting item with the Jog key. 154 ďźSwitch numberďź ďźD/R and EXPO rate displayďź Top rowďźLeft side ďź down Bottom rowďźRight side ďź up ďź Channel ďź 1ďźAileron 2ďźElevator 3ďźThrottle 4ďźRudder D/R â A channel is chosen by Jog key. Rangeďź1, 2, 4 ⥠Adjust the rate by moving the cursor to D/R with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left (down) or right (up) side and pressing the + key or â key. â ďź Rangeďź 0 âź 140% Defaultďź100% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step â Moving to another setting item of the same channel is possible by Jog key. EXPO â Select the "EXP" item and then select the channel with the Jog key. ⥠Adjust the rate by moving the cursor to EXP with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left (down) or right (up) side and pressing the + key or â key. â ďź Rangeďź1 âź 4 Rangeďź -100 âź +100% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step â Moving to another setting item of the same channel is possible by Jog key. Switch Change â Select the "SW" item and then select the channel with the Jog key. ⥠A switch is chosen by + key or â key. ďź â or RangeďźSwA âź SwH Glider Rangeďź1, 2, 4 155 Motor switch MOTOR SW (GLIDER) WING TYPE Function This function sets the operating motor when the EP glider with motor is started by switch. The operating speed can individually set in 2 ranges of high from slow and slow from high. If you do motor control with a throttle stick, you should set this function to INH. 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Ĺ)RUVDIHW\WKH212))VZLWFKRIWKHDLUFUDIWLWVHOI FDQEHVHW Ĺ,IDWUDQVPLWWHUSRZHUVXSSO\LVVZLWFKHGRQZKLOH WKH PRWRU 6: KDV EHHQ 21 WKH ZDUQLQJ ZLOO RSHUDWH%HVXUHWRVZLWFKRQDSRZHUVXSSO\ZLWK WKHPRWRUVWDUWVZLWFK2)) Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "MOTOR SW" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â Present motor control position MOTOR SW 02'(ăŁOFF ( 0%) 6$)(6:ăŁ6:$ăŁ'2:1 67576:ăŁ6:'ăŁ'2:1 (OFF) (ON) 326,ăŁăŁ 63(('ăŁ2))ăŁ2)) â Select the setting item with the Jog key. Motor â Decelerating speed setting â Activating the function â Select the "MODE" item and then select the "OFF" by pressing the + key or â key. ďź â or Glider â â Start SW â A setup of the motor control position (3CH end point)of Highside and Low-side â Accelerating speed setting â Switch selection ⥠Change the switch by pressing the + key or â key a t t h e s w i t c h selection item. â When you do not use a function, set to the "INH" side. â Switch direction ⢠Select the ďź " D O W N " it em or and then select the position by pressing the + key or â key. â If this safety switch is not ON, the motor will not start even if the starter switch is turned on. In "NULL", a safe function does not work. ďź RangeďźSwA âź SwH â Speed setting ⣠Select "SPEED " next to (OFF) and (ON) by Jog key. RangeďźOFF,1 âź 10(more slowly) â (ON) is the acceleration speed setting. â (OFF) is the deceleration speed setting. â 2P SWďźUP, DOWN â 3P SWďź UP, UP&D, UP&C, CNTR, C&DN, DOWN DANGER Always remove the propeller from the motor during setting and at operation checks. Ĺś7KHUHLVWKHGDQJHURIWKHSURSHOOHUVSLQQLQJXQH[SHFWHGO\DQGFDXVLQJDVHULRXVLQMXU\ 156 â or CONDITION Condition (GLIDER) WING TYPE Function The condition function lets you change multiple settings by one switch operation. Different settings can be made immediately by switching 2 conditions. 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Ĺ7KH IXQFWLRQV WKDW FDQ EH FKDQJHG E\ FRQGLWLRQ DUH ăť$LOHURQĹ5XGGHU ăť5XGGHUĹ$LOHURQ ăť&DPEHU)/3 ăť&DPEHU0,; ăť%XWWHUĂ\ ăť&DPEHUĹ(/( ăť(/(Ĺ&DPEHU ăť$,/Ĺ&DPEHU ăť$,/Ĺ%5.)/ ăť7ULPPL[ Method Calling the setting screen ⥠Select "CONDITION" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź CONDITION Condition1 â When not using this Function select INH. The display of On/Off is shown when active and assigned to a switch. ăŁINHăŁ6:$ăŁ'2:1 ăŁ,1+ăŁ6:$ăŁ'2:1 â Priority is given to the condition 2 when the condition 1 and 2 is turned on simultaneously. Condition2 â Select the setting item with the Jog key. ďźActivating the functionďź ďźSwitch directionďź ďźSwitch selectionďź CONDITION ďź â or Glider â Activating the function â Select the "INH" item of the condition you want to use and then set that condition to "ON" or "OFF" by pressing the + key or â key. â Set conditions you do not want to use to "INH". ďźChanging the switchďź â Switch selection ⥠Change the switch by pressing the + key or â key at the switch selection item. ďź â or â Switch direction ⢠Select the ON direction by pressing the + key or â key at the ON direction selection item. ďź â or Rangeďź RangeďźSwA âź SwH DefaultďźSwA â 2P SWďźNULL, UP, DOWN â 3P SWďźNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN 157 RUD â AIL Rudder â Aileron (GLIDER) WING TYPE Function This function is used when you want to mix the ailerons with rudder input. It is used when rudder is applied during roll maneuvers such as, knife edge flight. It can be used to turn or bank scale models, large models, etc. like a fullsize aircraft. 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Ĺ:KHQ WKH PL[LQJ GLUHFWLRQ LV UHYHUVHG E\ WKH OLQNDJH DGMXVWPHQWV FDQ EH PDGH E\ FKDQJLQJ WKHUDWHSRODULW\ Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "RUD â AIL" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź 58'âŤÚâŹ$,/ Activating the function Mixing rate â When not using this function, select INH. 0,;ăŁ,1+ 5$7(㣠1250 6:ăŁ6:$ 326,ăŁ'2:1 â Select the setting item with the Jog key. 3 Position Switch NULL ON UP ON UP&DWN ON ON OFF OFF ON 2 Position Switch NULL UP CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF OFF ON â The ON/OFF switch can be changed. (Selected by Jog key and changed by + key.) â Sets the ON/OFF direction of the selected switch. DOWN ON ON OFF ON OFF ON Glider RUD â AIL â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź 158 UP&CNT ON ON OFF OFF ON â When condition was used, the display can be switched and each connection can be set by switching the condition switch. â â Mixing rate ⥠S e l e c t t h e " R AT E " i t em a n d then adjust the mixing rate by pressing the + key or â key. ďź â or or Rangeďź-100 âź +100% Defaultďź0% â When you do not use a function, set to the "INH" side. â When you want to return the set value to the initial value, press the + key and â key simultaneously.However, polarity does not return. CAMBR FLP Camber ďŹap (GLIDER) WING TYPE Function 7KHXSGRZQWUDYHORIHDFKĂDS FDPEHUĂDSV )/3 EUDNH IODSV )/3 FDQ EH DGMXVWHG independently for each servo according to the ZLQJW\SH7KHFDPEHUĂDSVRSHUDWHVE\'7DQG WKHEUDNHĂDSVRSHUDWHVE\'7 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Aileron1 (CH1) Flap1 Flap3 (Camber Flap) (Brake Flap) (CH5) (CH8) Flap4 (Brake Flap) Aileron2 (CH9) Flap2 (CH7) (Camber Flap) (CH6) Ĺ7KHD[LVRIHDFKĂDSFDQEHVKLIWHG Ĺ7KH FRQWURO VZLWFK FDQ EH FKDQJHG E\ $8; FKDQQHO Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "CAMBR FLP" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź D T5 a n d D T6 s e t the amount of movement when the ďŹap is operated. â Flap1 â Flap2 â Flap3 â Flap4 &$0%5ĺ˛)/31 &$0%(5)/$3 â Select the setting item with the Jog key. 83 '1 2)6 )ăŁ+100ăŁăŁ )ăŁăŁăŁ )ăŁăŁăŁ )ăŁăŁăŁ â Up side rate â Down side rate â OďŹset rate â â The number is changed by + key or â key. ďźCurrently selected conditionďź &$0%5ĺ˛)/3 âŤŮâŹ1250 12 %5$.()/$3âŤÚâŹĺ˛ĺ˛&$0%(5 83 '1 2)6 )/ăŁ+100ăŁăŁ â Selection of whether or not mixing from brake FLP to camber FLP is performed 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 â Brake FLP to camber FLP mixing switch selection Glider Camber FLP ďźpage [BrakeďŹap â CamberďŹap] ďź â Brake FLP to camber FLP mixing rate and offset (axis shift) â Brake FLP to camber FLP mixing switch operation direction 159 CAMBR MIX Camber mixing (GLIDER) WING TYPE Function This function adjusts the rate of camber operation for the wing camber (ailerons, camber flaps, brake flaps) in the negative and positive directions. The aileron, flap, and elevator rates can also be adjusted independently and attitude changes caused by camber operation can be All the wing control surfaces are lowered and the camber is increased (lift increases) Attitude changes are compensated for by setting the amount of elevator movement. 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F corrected. ,QLWLDOVHWWLQJDVVLJQVFDPEHURSHUDWLRQWRVLGHOHYHU'7 Ĺ2SHUDWLRQFDQEHWXUQHGRQDQGRIIE\VZLWFK Ĺ95FDQEHFKDQJHGE\$8;FKDQQHO All the wing control surfaces are raised and the camber is decreased (lift decreases) Turn the VR Attitude changes are compensated for by setting the amount of elevator movement. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "CAMBR MIX" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Sets the amount of movement when the VR was turned. ďźCurrently selected conditionďź &$0%5ĺ˛0,; 1250 1 2 5$7( 5$7( $,/㣠0 㣠$,/ăŁăŁ 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 Glider â Aileron1 â Aileron2 â Camber MIX ACT/INH â Can be set to operate from a switch. When NULL, it is operated by a VR. ( R AT E1)ďźT h e a m o u n t o f operations when VR is turned to the right. ďź â â The number is changed by + key or â key. ( R AT E2)ďźT h e a m o u n t o f operations when VR is turned to the left. Sets the amount of [Camber FLP ďźpage] ďźCurrently selected conditionďź movement when &$0%5ĺ˛0,; 1250 1 2 the VR is turned. â Flap1 â Flap2 â Flap3 â Flap4 â Elevator 160 â Select the setting item with the Jog key. 5$7( 5$7( )/3ăŁ0㣠)/3ăŁăŁ )/3ăŁăŁ )/3ăŁăŁ (/(ăŁăŁ â Amount of compensation of the elevator when the camber changed. BUTTERFLY ButterďŹy mixing (GLIDER) WING TYPE Function 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F 6ORZWKHDLUFUDIW¡VYHORFLW\ 3 URYLGH ZDVKRXW DW WKH ZLQJ WLSV WR UHGXFH WKH WHQGHQF\WRWLSVWDOO & UHDWH PRUH OLIW WRZDUG WKH FHQWHU RI WKH ZLQJ DOORZLQJLWWRĂ\DWDVORZHUVSHHG Ĺ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\ VHWWLQJDVZLWFK Ĺ 7KH SRLQW DW ZKLFK WKH EXWWHUIO\ RSHUDWLRQ UHIHUHQFHSRLQWFDQEHRIIVHW Ĺ7KHGLIIHUHQWLDOUDWHFDQEHDGMXVWHG This function is utilized to quickly slow the aircraft and reduce altitude by simultaneously raising the left and right ailerons and lowering the ĂDSV FDPEHUĂDSEUDNHĂDS Butterfly (Crow) produces an extremely HIÂżFLHQWODQGLQJFRQÂżJXUDWLRQE\DFFRPSOLVKLQJ WKHIROORZLQJ OFF ON Switch set to ON Resistance increased by raising the elevators and lowering the ďŹaps THR stick lowered Fine tuning of an elevator Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "BUTTERFLY" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź ďźCurrently selected conditionďź Amount of movement setting â Aileron1 â Aileron2 â Amount of elevator compensation â ButterďŹy : ACT/INH â Can be either set to a switch or when NULL is controlled by the THR stick. %877(5)/<ĺ˛ĺ˛ĺ˛ $,/㣠$,/㣠(/(㣠1250 1 )/3㣠)/3㣠)/3㣠)/3㣠0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 2)67㣠â OďŹset setting âSelect "OFST" XX%. ďź â â The number is changed by + key or â key. â When MIX is set to ACT, the amount of MIX(s) according to stick operation is displayed. Brake amount MAX Glider â Current THR stick position 0ďź : High 100ďź : Low â Select the setting item with the Jog key. OFST âś 0% At THR stick high press the Jog key for 1 second High Slow THR stick operation Brake amount MAX OFST âś50% At THR stick center press the Jog key for 1 second Start from center High Slow THR stick operation 161 CAMBR â ELE Camber â Elevator mixing WING TYPE Function (GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F When the camber/speed flaps are utilized, the aircraft might experience, a change in pitch. This mix compensates for such changes by incorporating elevator input. Flap operation pitch change Ĺ 7KH HOHYDWRU VHUYRV XSGRZQ UDWHV FDQ EH DGMXVWHG VHSDUDWHO\ ,I WKH PL[LQJ GLUHFWLRQ LV UHYHUVHGFKDQJHWKHPL[LQJUDWHSRODULW\ RU² Ĺ 0L[LQJ GXULQJ IOLJKW FDQ EH WXUQHG 212)) E\ VHWWLQJDVZLWFK $OZD\V21DW6:>18//@VHWWLQJ Flap1 (CH5) Flap2 (CH6) compensated for by elevators Elevator (CH2) Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "CAMBR â ELE" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź &$0%5âŤ(ÚâŹ/( 1250 Mixing rate 5$7( 5$7( (/(ăŁ0㣠Activating the function 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 â Select the setting item with the Jog key. 3 Position Switch NULL ON UP ON ON ON OFF ON OFF ON 2 Position Switch NULL UP UP&CNT ON OFF OFF ON UP&DWN CENTER OFF ON OFF CNT&DN OFF ON ON DOWN Glider ON ON OFF ON OFF ON OFF OFF ON â When condition is used, the display can be switched and each connection can be set by switching the condition switch. â The ON/OFF switch can be changed. ( S e l e c t e d w i t h t h e Jog key a n d changed with the +key) â Sets the ON/OFF direction of the selected switch. â ( R AT E1) a n d ( R AT E2) s h o w t h e direction of camber of operation. Camber â ELE mixing â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. 162 DOWN â When not using this function, select INH. â Mixing rate ⥠S e l e c t t h e " R AT E " i t em a n d then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź-120 âź +120% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. ELE â CAMBR Elevator â Camber mixing WING TYPE Function This function is used when you want to mix the FDPEHUĂDSVZLWKHOHYDWRURSHUDWLRQ:KHQXVHG the flaps are lowered by up elevator, and lift is increased. (GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Ĺ,QĂLJKWPL[LQJFDQEHWXUQHG212))E\DVVLJQLQJ WKLVWRDVZLWFK $OZD\V21DW6:>18//@VHWWLQJ Ĺ7KHPL[LQJUDWHFDQEHDGMXVWHG Ĺ6HWWLQJVRWKDWWKHĂDSVDUHQRWRSHUDWHGQHDUWKH FHQWHURIWKHHOHYDWRUVLVSRVVLEOH 5$1*( Aileron1 (CH1) Flap1 Flap3 (Camber Flap) (Brake Flap) (CH5) (CH8) Up the elevator Flap4 (Brake Flap) Aileron2 (CH9) Flap2 (CH7) (Camber Flap) (CH6) ďŹap is down Elevator (CH2) Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "ELE â CAMBR" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź ďźCurrently selected conditionďź Mixing rate â Aileron1 â Aileron2 â Camber MIX ACT/INH â Can be either set to a switch or when NULL is always active. (/(âŤ&ÚâŹ$0%5 1250 12 5$7( 5$7( $,/ăŁ0㣠$,/ăŁăŁ 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 5$1*(㣠â Described on the next page. â Current position of the elevator stick â Select the setting item with the Jog key. ďź â â The number is changed by + key or â key. ďźCurrently selected conditionďź Mixing rate (/(âŤ&ÚâŹ$0%5 1250 â Flap1 â Flap2 â Flap3 â Flap4 5$7( 5$7( )/3ăŁăŁ )/3ăŁăŁ )/3ăŁăŁ )/3ăŁăŁ Glider [ELE â Camber ďźpage] â (RATE1) and (RATE2) show the direction of elevator of operation. 163 ďźELE â Camber ďź (/(âŤ&ÚâŹ$0%5 1250 12 5$7( 5$7( $,/ăŁăŁ $,/ăŁăŁ 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 5$1*(㣠â When MIX is set to ACT, the amount of MIX(s) according to stick operation is displayed. â Setting that inhibits camber mixing near the elevator center position. Setting so that camber mixing is performed only when the elevators were operated greatly is possible. RANGE setting â Setting state â Select the "0%" item next to RANGE with the Jog key. â To setting value ⥠Move the elevator stick to the position you want operation to begin. Can be either up or down. When set to down, the up side is also set by the same amount. â Set value memorization ⢠Press the Jog key for 1 second. Hold the stick in position. (/(âŤ&ÚâŹ$0%5 1250 12 5$7( 5$7( $,/ăŁăŁ $,/ăŁăŁ 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 5$1*(㣠When elevator operation exceeds the range, the stick position is displayed and mixing is performed. Glider 164 â When a RANGE number is selected and the Jog key is pressed for 1 second, RANGE is reset to 0% and normal mixing is performed. AIL â CAMBR Aileron â Camber mixing WING TYPE Function 7KLVPL[LQJOLQNVWKHFDPEHUĂDSVZLWKDLOHURQ operation (stick). It is used when you want to increase roll axis maneuverability. (GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Ĺ:KHQ WKH PL[LQJ GLUHFWLRQ LV UHYHUVHG E\ WKH OLQNDJH DGMXVWPHQWV FDQ EH PDGH E\ FKDQJLQJ WKHUDWHSRODULW\ Flaps and ailerons operate OFF ON Set switch to ON Roll is corrected by using the ailerons to control the camber FLP. Ailerons operation Method Calling the setting screen ⥠Select "AIL â CAMBR" from the menu with the Jog key. â Call the menu screen from the home screen by pressing the + key for 1 second. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź $,/âŤ&ÚâŹ$0%5 1250 Mixing rate /()7 5,*+7 )/3ăŁ0㣠)/3ăŁăŁ 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 Activating the function â Select the setting item with the Jog key. 3 Position Switch NULL ON ON ON UP UP&DWN ON ON ON OFF OFF OFF OFF ON 2 Position Switch NULL UP UP&CNT ON CENTER OFF ON CNT&DN OFF ON OFF ON DOWN OFF OFF ON â When not using this function, select INH. â When condition was used, the display can be switched and each connection can be set by switching the condition switch. â The ON/OFF switch can be changed. ( S e l e c t e d w i t h t h e Jog key a n d changed with the +key) â Sets the ON/OFF direction of the selected switch. DOWN ON OFF ON OFF ON Glider ON AIL â Camber mixing â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. â Mixing rate ⥠S e l e c t t h e " R AT E " i t em a n d then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź-120 âź +120% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. 165 AIL â BRKFL Aileron â Brake ďŹap mixing WING TYPE Function This mixing links the brake flaps with aileron operation (stick). It is used when you want to increase roll axis maneuverability. (GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Ĺ:KHQ WKH PL[LQJ GLUHFWLRQ LV UHYHUVHG E\ WKH OLQNDJH DGMXVWPHQWV FDQ EH PDGH E\ FKDQJLQJ WKHUDWHSRODULW\ Flaps and ailerons operate OFF ON Set the switch to ON Roll is corrected by using the ailerons to control the brake FLP. Ailerons operation Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "AIL â BRKFL" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź $,/âŤÚâŹ%5.)/ 1250 Mixing rate Activating the function â Select the setting item with the Jog key. /()7 5,*+7 )/3ăŁ0㣠)/3ăŁăŁ 0,;ăŁ,1+ 6:ăŁ6Z$ăŁ'2:1 3 Position Switch NULL ON UP ON OFF OFF ON 2 Position Switch NULL UP UP&CNT ON ON OFF OFF ON UP&DWN ON ON CENTER OFF ON OFF CNT&DN OFF ON ON OFF ON â When condition was used, the display can be switched and each connection can be set by switching the condition switch. â The ON/OFF switch can be changed. ( S e l e c t e d w i t h t h e Jog key a n d changed with the +key) â Sets the ON/OFF direction of the selected switch. DOWN Glider ON ON OFF ON OFF ON AIL â BRKFL mixing â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â or â When you do not use a function, set to the "INH" side. 166 DOWN OFF â When not using this function, select INH. â Mixing rate ⥠S e l e c t t h e " R AT E " i t em a n d then adjust the mixing rate by pressing the + key or â key. ďź â or Rangeďź-120 âź +120% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Trim mix TRIM MIX (GLIDER) WING TYPE Function 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Ĺ7KHVHUYRVSHHGDWZKLFKWULPLVWRWKHVHWSRVLWLRQ FDQEHVHW This function shifts the ailerons, elevators, and HDFKĂDSWULPWRWKHSUHVHWSRVLWLRQE\PHDQVRID switch. OFF Aileron1 (CH1) Flap1 Flap3 (Camber Flap) (Brake Flap) (CH5) (CH8) ON Set the switch to ON Trim of each control surface is moved to the set value. Flap4 (Brake Flap) Aileron2 (CH9) Flap2 (CH7) (Camber Flap) (CH6) Elevator (CH2) Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "TRIM MIX" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź [TRIM MIX page1] TRIM MIX â [TRIM MIX page2] â The number is changed by + key or â key. TRIM Activating the function MIX 12 0,;ăŁINH 6:ăŁ6Z$ ăŁ'2:1 '(/$< $,/ăŁ2)) )/3ăŁ2)) (/(ăŁ2)) 3 Position Switch NULL ON ON UP ON OFF OFF 2 Position Switch NULL UP UP&DWN ON OFF ON DOWN ON ON OFF ON OFF ON UP&CNT ON ON OFF CENTER OFF ON OFF CNT&DN OFF ON ON â Sets the trim neutral position of each control surface. Rangeďź-100 âź +100 Returned to 0 by pressing the + key and â key simultaneously. DOWN OFF OFF ON â The ON/OFF switch can be changed. (Selected with the Jog key and changed with the +key) â Sets the ON/OFF direction of the selected switch. Glider â When not using this function, select INH. ON 12 $,/ăŁ0 )/3ăŁ0 $,/ăŁ0 )/3ăŁ0 (/(ăŁ0 )/3ăŁ0 )/3ăŁ0 â Select the setting item with the Jog key. ďź (NORM) â When condition is used, the display can be switched and each connection can be set by switching the condition switch. â Servo speed at which the trim position is to the set position. Sudden attitude changes are prevented by turning the switch on. (Selected by Jog key and changed by + key and â key.) RangeďźOFF(fast shiftďźă1 âź 10ďźslow shiftďź Returned to OFF by pressing the Jog key for a long time. *This is not the servo speed when the stick was operated. 167 Multicopter Function The setting screen of each function is called from the following menu. The function when the model type was set to multicopter (MULTI COPT) is displayed here. Power ON â First set the throttle to slow. To menu screen by holding down the + key â Then turn on the power. ďźHome screenďź â When t h e E N D k e y i s pressed, the display returns to the home screen. â When the + key is pressed for 1 second, the menu screen is ďź1 secondďź displayed. ďź END MENU 0(18ĺ˛ĺ˛ĺ˛ĺ˛1 0(18ĺ˛ĺ˛ĺ˛ĺ˛1 MENU 1/2 ăŁ0'/6(/ ăŁ0'/1$0( ăŁ)$,/6$)( ăŁ5(9(56( ăŁ7,0(5 ăŁ6(592 ăŁ(1'32,17 ăŁ75,0 ăŁ68%75,0 ăŁ30,; ăŁ$8;&+$1 ăŁ3$5$0(7(5 Multicopter 0(18ĺ˛ĺ˛ĺ˛ĺ˛12 MENU 2/2 ăŁ7(/(0(75< ăŁ6(1625 ăŁ6%86/,1. ăŁ0'/75$16 ăŁ75$,1(5 ăŁ*<526(16 ăŁ'5(;32 ăŁ&175$/50 ďźSelectionďź â Move the cursor (highlighted) up and down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. ďźCalling the setting screenďź â Press the Jog key to open the setting screen. 168 key ďź LCD âďź key ââ key âJog key âEND key Refer to "Common Functions" previously described for a description of this function. â Function MENU1/3 MDL-SEL MENU2/3 (P.40) TELEMETRY (P.66) Model select ďź Model Copy ďź Data reset ďź RX ďź Link Telemetry Display ďź Alarm setup MDL-NAME Telemetry sensor (P.43) Model name ďź User name FAIL SAFE (P.45) Fail safe REVERSE (P.47) Servo reverse TIMER (P.48) Timer SERVO SENSOR SBUS LINK MDL-TRANS TRAINER CNTR ALRM Trim reset ďź Trim step SUB TRIM (P.52) Sub trim P.MIX1-6 Center alarm (P.171) (P.173) Multicopter Dual rate ďź EXPO (P.51) (P.170) Gyro mixing D/R, EXPO TRIM (P.93) Trainer END POINT End point (P.92) Data transfer of another T10J Servo monitor ďź Servo test (P.50) (P.89) S.BUS servo set up GYRO SENS (P.49) (P.83) (P.53) Program mixing 1 âź 6 AUX-CHAN (P.56) AUX channel PARAMETER (P.58) Data reset ďź Model type ďź ATLtrim ďź LCD contrast ďź Back light : mode, time, adjustment ďź Home display ďź Battery alarm ďź Battery vibration ďź Buzzer tone ďź Jog navi ďź Jog light ďź Jog time ďź Telemetry : mode, unit ďź Speech : language, volume ďź Stick position alarm 169 GYRO SENS Gyro sensor (MULTICOPT) Ĺ7KH VHQVLWLYLW\ VZLWFK FDQ EH VHOHFWHG DQG WKH VHQVLWLYLW\RIHDFKGLUHFWLRQRIWKHVZLWFKFDQEH VHW 6ZLWFKHV$WR+ Ĺ&+ &+&+ &+&+ RU &+&+&+ FRPELQDWLRQV FDQ EH VHOHFWHG DV WKH VHQVLWLYLW\ VHWWLQJFKDQQHO Function This function is dedicated mixing for switching the gyro sensitivity and gyro mode (AVCS/ NORMAL) of Futaba gyros. Up to 3 axes can be set. The attitude control of multicopter uses the system of multicopter attachment. This "GYROSENS" will be used for accessories, such as camera control. *When this function is used, it becomes impossible for CH5 to use it for multi copter controller. Use CH6 for multi copter controller and use SwC. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "GYRO SENS" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â When not using this function, select INH. GYRO SENS Activating the function Gain Channel selection Switch direction Gain switch selection ďźC u r r e n t s w i t c h o p e r a t i n g directionďź Gyrotype, Gain rate â Select the setting item with the Jog key. ďźGyro typeďź ďźGyro Gainďź â Switches to the sensitivity setting screen of each switch direction when the Jog key is pressed. â When using a Futaba GYA gyro, select gyro type GY. This switches the gyro sensitivity setting item to mode and sensitivity direct reading display. Multicopter GYRO SENS â Activating the function â Select the "MIX" item and then select the "ON" by pressing the + key or â key. ďź â Sensitivity switch selection ⥠Select the "SW" item and then select the switch by pressing the + key or â key. â or ďź â When you do not use a function, set to the "INH" side. â Sensitivity setting channel selection ⢠Select the ďź â " C H " i tem an d or then select the sensitivity setting channel by pressing the + key or â key. RangeďźCH5ăCH5/CH7ă CH5/CH8ăCH5/CH7/CH8 DefaultďźCH5 170 â or RangeďźSwA âź SwHăDefaultďźSwA â Gyro type and sensitivity setting ⣠Press the Jog key and select the sensitivity setting screen you want to set and then set type (gyro type) and rate (gyro sensitivity) of each channel by pressing the +key or â key. ďź"type"ďźRangeďźSTD,GY DefaultďźSTD ďź"rate"ďźRangeďź0 âź 100%ďźSTDďź, NOR100 âź 0 âź AVC100% ďźGYďź Defaultďź50% ďźSTDďź, 0% ďźGYďź â When you want to return the set value to the initial value, press the + key and â key simultaneously. D/R,EXPO Dual rate ďź EXPO (MULTICOPT) Function D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps Ĺ7KHFRQWUROVXUIDFHDQJOHLVDGMXVWHGE\HDFKGLUHFWLRQRIWKHVZLWFK7KHOHIWDQGULJKW XSDQGGRZQ GLUHFWLRQRIHDFKVZLWFKFDQEHVHWLQGLYLGXDOO\ EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle. Ĺ7KH´¾VLGHPDNHVVHUYRPRYHPHQWVOXJJLVKDQGWKH´¾VLGHPDNHVVHUYRPRYHPHQWVHQVLWLYHQHDU WKHQHXWUDOSRVLWLRQ([SRQHQWLDOLVDSSOLHGWRHQWLUHWKURWWOHVHUYRWUDYHO:KHQWKH´¾VLGHLVLQFUHDVHG WKHVORZVLGHEHFRPHVVOXJJLVKDQGWKHKLJKVLGHEHFRPHVVHQVLWLYH Ĺ6HWWLQJFRUUHVSRQGLQJWRHDFKUDWHRIGXDOUDWH '5 LVSRVVLEOH ([FHSWWKURWWOH 7KHGLUHFWLRQRIHDFK VZLWFKDQGWKHOHIWDQGULJKW XSDQGGRZQ GLUHFWLRQRIHDFKFKDQQHOFDQEHVHWLQGLYLGXDOO\ Switch selectionďźSWďź Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate (exponential) switch. Ĺ'HIDXOWďź$LOHURQďź6ZLWFK' ďź (OHYDWRUďź6ZLWFK$ ďź 5XGGHUďź6ZLWFK% Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "D/R,EXPO" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź Multicopter â The channel under selection is underlined. Channel selection Dual rate ďźSwitch Directionďź EXPO â The dual rate and exponential settings are displayed by a curve. Switch selection â Channel selection/Select the setting item with the Jog key. ďźSwitch numberďź ďźD/R and EXPO rate displayďź Top rowďźLeft side ďź down Bottom rowďźRight side ďź up ďź Channel ďź 1ďźAileron 2ďźElevator 3ďźThrottle 4ďźRudder 171 D/R â A channel is chosen by Jog key. Rangeďź1, 2, 4 ⥠Adjust the rate by moving the cursor to D/R with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left (down) or right (up) side and pressing the + key or â key. â ďź Rangeďź 0 âź 140% Defaultďź100% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step â Moving to another setting item of the same channel is possible by Jog key. EXPO â Select the "EXP" item and then select the channel with the Jog key. ⥠Adjust the rate by moving the cursor to EXP with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left (down) or right (up) side and pressing the + key or â key. â ďź Rangeďź1 âź 4 Rangeďź -100 âź +100% Defaultďź0% â When you want to return the set value to the initial value, press the + key and â key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step â Moving to another setting item of the same channel is possible by Jog key. Multicopter Switch Change â Select the "SW" item and then select the channel with the Jog key. ďź â or Rangeďź1, 2, 4 172 ⥠A switch is chosen by + key or -key. RangeďźSwA âź SwH CNTR ALRM Center alarm (MULTICOPT) Function $QDODUP VLQJOHEHHS FDQEHVRXQGHGDWWKHVSHFLÂżHGWKURWWOHVWLFNSRVLWLRQ Ĺ$ODUPIXQFWLRQ212))FDQEHVHWE\VZLWFK Beep sounds When the THR stick is set to the speciďŹed position. Method Calling the setting screen â Call the menu screen from the home screen by pressing the + key for 1 second. ⥠Select "CNTR ALRM" from the menu with the Jog key. ⢠Open the setting screen by pressing the Jog key. ďź ďź1 secondďź â Select the item with the Jog key. STK POSI ALRM 02'(ăŁON 6:ăŁ6Z$ 326,ăŁ'2:1 67,&.㣠â When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. â The number in parenthesis is the current throttle stick position. Position setting â Stick position is chosen by Jog key. ⥠Set the throttle stick to the position at which you want to generate the alarm. Multicopter INH â ON/OFF Switch selsction Switch direction Stick position CNTR ALRM ⢠When the Jog key is held down the alarm sounds at that position. CNTR ALRM STK POSI ALRM 02'(ăŁON 6:ăŁ6Z$ 326,ăŁ'2:1 67,&.ăŁ45% ( THR Stick Memorize the position at which the beep is to sound. 45%) 173 TX SETTING The settings here are special settings that are unnecessary during normal use. The stick mode can be changed and stick adjustment (calibration), throttle lever reverse, and language can be set. Turn on the power switch with the + key and â key pressed in the power oďŹ state. The screen shown at the left appears. To return to the home screen, turn off the power and then turn the power back on without pressing the keys. TX SETTING STK-MODE STK-ADJ THR-REV NEXT NOR LANGUAGE Englishá´ž â STK-MODE AIL RUD ELE THR THR ELE MODE 1 RUD AIL AIL RUD MODE 2 RUD AIL ELE THR This is the MODE1 âź MODE4 setting. The initial state is MODE2. To change the mode the stick ratchet must be changed. Request that this be done by Futaba Service. (Charged modiďŹcation) THR ELE MODE 4 MODE 3 â STK-ADJ This function is normally not used. If stick deviation should occur, make this adjustment. Do not use it in the normal state. Calling the setting screen â Turn off the power and then turn the power back on while pressing the + key and â key simultaneously. ďź âĄ Select STK-ADJ â NEXT in the menu with the Jog key. ⢠Enter the setting screen by pressing the Jog key. ⥠Press the Jog key down and select NEUT â . ⢠Set the stick to the neutral position and press the Jog key. â Stick adjustment â Select the stick you want to adjust with 1 âź 4 with the + key. ďź 174 ⣠Swing the selected stick fully to the left and right (up and down). ⤠â appears next to "LEFT" and "RGHT". Press the Jog key. ⼠When "COMPLETE" is displayed, adjustment is complete. END â THR-REV This function is not used. When you want to use full throttle with the throttle stick down and slow with the throttle stick up, select REV. When the stick is up, trim is eďŹective and when the stick is down, trim is not eďŹective. *Throttle servo operation reversed by the linkage is usually performed by reverse in the normal menu. When throttle servo operation is reversed with the THR-REV function, trim becomes ineďŹective at slow. THR-REV â Turn off the power and then turn on the power while pressing the + key and â key simultaneously. ďź âĄ Select THR-REV â NOR in the menu with the Jog key. ⢠Select NOR or REV by pressing the + key or â key. Setting is ended by power oďŹ. ďź â â â LANGUAGE The language displayed at proportional can be changed. The initial setting is Japanese, but can be selected from among 7 languages. LANGUAGE â Turn off the power and then turn on the power while pressing the + key and â key simultaneously. ďź âĄ Select LANGUAGE â English in the menu with the Jog key. ⢠Select NOR or REV by pressing the + key or â key. Setting is ended by power oďŹ. ďź â â Return from the transmitter setting screen to the normal menu by turning on the power without pressing a key. FUTABA CORPORATION 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 2014, 01 (1) 175
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Modify Date : 2014:01:27 13:51:14+08:00 Create Date : 2014:01:27 13:51:14+08:00 Metadata Date : 2014:01:27 13:51:14+08:00 Format : application/pdf Title : untitled Document ID : uuid:f84a778d-f964-4b4a-a744-18a153050e07 Instance ID : uuid:855a7a24-dbbb-483b-8746-d6fac2e8c28f Producer : Acrobat Distiller 7.0.5 (Windows) Page Count : 138 Creator : Adobe Acrobat 7.0EXIF Metadata provided by EXIF.tools