Futaba T2PL-FM-75 Radio Control Transmitter User Manual 2PL FM ENG 0

Download:
Mirror Download [FCC.gov]
Document ID	675832
Application ID	jS6ha+38KcXb8RCm9e5EGw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	61.89kB (773663 bits)
Date Submitted	2006-06-30 00:00:00
Date Available	2006-06-30 00:00:00
Creation Date	2006-06-22 10:48:32
Producing Software	Acrobat Distiller 5.0.1 for Macintosh
Document Lastmod	2006-06-22 10:48:32
Document Title	2PL_FM_ENG_0
Document Creator	PageMaker 6.5J
Document Author:	morimoto

Thank you for purchasing a Futaba 2PL-FM.
Before using your 2PL-FM, read this manual carefully and use your R/C set safely.
After reading this manual, store it in a safe place.
Application, Export, and Modification
1. This product may be used for models only. It is not intended for use in any application other than the
control of models for hobby and recreational purposes. The product is subject to regulations of the
Ministry of Radio/Telecommunications and is restricted under Japanese law to such purposes.
2. Exportation precautions:
(a) When this product is exported from the country of manufacture, its use is to be approved by the
laws governing the country of destination which govern devices that emit radio frequencies. If this
product is then re-exported to other countries, it may be subject to restrictions on such export. Prior
approval of the appropriate goverment authorities may be required. If you have purchased this product
from an exporter outside your country, and not the authorized Futaba distributor in your country,
please contact the seller immediately to determine if such export regulations have been met.
(b) Use of this product with other than models may be restricted by Export and Trade Control Regulations, and an application for export approval must be submitted. In the US, use of 72MHz (aircraft
only), 75MHz (ground models only) and 27MHz (both) frequency bands are strictly regulated by the
FCC. This equipment must not be utilized to operate equipment other than radio controlled models.
Similarly, other frequencies (except 50MHz, for HAM operators) must not be used to operate models.
3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorized
modification, adjustment, and replacement of parts on this product. Any such changes may void the
warranty.
Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation of America, model number R153F complies with part 15
of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
The responsible party of this device compliance is;
Futaba Corporation of America
2865 Wall Triana Highway, Huntsville, Alabama 35824, U.S.A.
TEL (256) 461 - 7348
Battery Recycling (for U.S.A.)
The RBRCTM SEAL on the (easily removable) nickel-cadmium battery contained in
Futaba products indicates that Futaba Corporation of America is voluntarily participating
in an industry program to collect and recycle these batteries at the end of their useful
lives, when taken out of service within the United States. The RBRCTM program provides
a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste system, which is illegal in some areas.
You may contact your local recycling center for information on where to return the spent battery.
Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Futaba Corporation of America's involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
NOTE: Our instruction manuals encourage our customers to return spent batteries to a local recycling
center in order to keep a healthy environment.
RBRCTM is a trademark of the Rechargeable Battery Recycling Corporation.
Warning: This product contains a chemical known to cause cancer and birth defects (or other
reproductive harm).
•No part of this manual may be reproduced in any form without prior permission.
•The contents of this manual are subject to change without prior notice.
•This manual has been carefully written. Please write to Futaba if you feel that any corrections or clarifications should
be made.
•Futaba is not responsible for the use of this product.
Table of Contens
Safety Precautions ...................................................................... 2
Definition of Symbols ............................................................................................................ 2
Running Preparations Safety Precautions .......................................................................... 2
Running Safety Precautions ................................................................................................. 3
Storage and Disposal Safety Precautions ........................................................................... 4
Other Safety Precautions ..................................................................................................... 5
Before Operation ........................................................................ 6
System Contents ................................................................................................................... 6
Nomenclature / Handling ..................................................................................................... 7
Assembly / Adjustment .............................................................. 9
Receiver and Servo Connection .......................................................................................... 9
Assembly Precautions ........................................................................................................... 9
Transmitter Set-Up Procedures........................................................................................ 11
Description of 2PL-FM Functions............................................ 12
Steering Trim (TRM-CH1) ................................................................................................. 12
Throttle Trim (TRM-CH2) ................................................................................................. 12
Steering Dual Rates (D/R-CH1) ......................................................................................... 13
Model Selection/Model Reset (MDL) ................................................................................ 13
Steering Servo Reversing (REV-CH1) ............................................................................... 13
Throttle Servo Reversing (REV-CH2) ............................................................................... 13
Steering End Point Adjustment (EPA-CH1) .................................................................... 14
Throttle End Point Adjustment (EPA-CH2) .................................................................... 14
ABS function (ABS-CH2) ................................................................................................... 14
Model Name (NAME) ......................................................................................................... 14
MC230CR/MC330CR........................................................................................................... 15
Flow Chart of 2PL-FM Functions ............................................ 16
*Each function is easily selected with the SELECT key and set with the digital
trim DT1/DT2.
Reference ................................................................................... 18
Ratings .................................................................................................................................. 18
Troubleshooting .................................................................................................................. 19
Safety Precautions
For your safety as well as that of others, please read this manual thoroughly prior to installation and operation of your digital proportional R/C system.
Definition of Symbols
Safety Precautions
The following defines the symbols used in this manual.
Explanation of Symbols
Danger
Procedures which may lead to a dangerous condition and cause
death or serious injury to the user if not carried out properly.
Warning
Procedures which may lead to a dangerous condition or cause
death or serious injury to the user if not carried out properly, or
procedures where the probability of superficial injury or physical
damage is high.
Caution
Procedures where the possibility of serious injury to the user is
small, but there is a danger of injury, or physical damage, if not
carried out properly.
Explanation of Graphic Symbols
Indicates an operation that prompts a warning (including Caution).
Indicates an operation that must not be performed.
Indicates an operation that always must be performed.
Running (Sailing) Preparations Safety Precautions
Warning
(When using a Ni-cad battery to power your system)
Charging
When using a Ni-cad battery to power your system, always charge and check the
battery voltage prior to operation.
Should the battery discharge below the minimum voltage level, control will be lost.
Caution
(When using a Ni-cad battery to power your system)
When the charger is not in use, disconnect it from the outlet.
This will prevent accidents, overheating and short circuits.
Running (Sailing) Safety Precautions
Warning
Prior to operation always perform a range test.
Even one abnormality in the R/C system may cause loss of control.
[Range Test Procedure]
Have a friend hold the model, or place on a stand where the wheels or prop can not
come in contact with any object. Collapse the transmitter antenna and operate from a
distance of about 100 feet. Be sure to check the movement of each servo to make sure
it follows the movement of the steering wheel and throttle trigger. If the servos do not
follow the commands from the transmitter or any type of interference is detected, Do
Not operate the model.
Fully extend the transmitter antenna.
If the transmitter antenna is not fully extended, range will be reduced and control may
be lost.
Safety Precautions
Conduct Tests
Prohibited
Do not operate two or more models on the same frequency at the same time.
Operation of two or more models on the same frequency at the same time will cause
interference and loss of control of both models.
AM, FM and PCM are different methods of modulation. Nonetheless the same frequency can not be used at the same point in time, regardless of the signal format.
Do not operate outdoors on rainy days
Never operate in the rain or run through puddles.
The transmitter, receiver, batteries and most servos, and speed controls are not waterproof. Contact with any type of moisture or immersion in water or snow will cause
damage along with possible loss of control. Should any type of moisture enter any
component of the system, immediately stop using the R/C system and return it to our
service center for inspection.
Prohibited
Do not operate when visibility is limited.
Should you lose sight of the model, a collision or other dangerous situation may occur.
Prohibited
Do not operate near people or roads.
Do not operate near high tension power lines or communication broadcasting antennas.
Prior to the operation of any model be sure the area you plan to use is safe. Be aware
of all objects that may be in the path of your model. Do not operate the model where
people or any type of moveable object could stray in the path of your model. Control
loss due to interference, component failure, loss of sight or low battery voltage could
result in serious injury to yourself and others as well as damage to your model.
Prohibited
Do not operate your R/C system within 1 mile of another site where radio control activity may occur.
Interference from other R/C systems will cause loss of control.
Prohibited
Do not operate when you are tired, not feeling well or under the influence of alcohol or
drugs.
Your judgment is impaired and could result in a dangerous situation that may cause
serious injury to yourself and others.
Safety Precautions
Before you turn on the power switch on the transmitter, always check to see that the
trigger is at the neutral position. Always turn the transmitter on first, then the receiver.
When you turn the system off, always turn the receiver off first and then the transmitter. This step is very important. Always follow this procedure.
If this procedure is not followed, injury to yourself and others as well as loss of control
could occur.
Adjustment Note
Make all adjustments to the radio control system with engine not running, or the electric motor disconnected.
If the engine is running or the motor is connected while adjustments are made, the
model may run out of control.
Remove the main battery source from electric powered models when they are not
being used.
Should you accidentally leave the receiver switch on, the model could run out of control.
Caution
Do not touch
Do not touch the engine, motor, speed control or any part of the model that will generate heat while running.
Touching hot parts will result in serious burns.
Storage and Disposal Safety Precautions
Warning
(When using a Ni-cad battery to power your system)
At the end of a day's operation, store the system with Ni-cad battery discharged. Be
sure to recharge the system before it is used again.
You should fully discharge your system's batteries periodically to prevent a condition
called "memory". For example, if you only make two runs in a day or you regularly use
a small amount of battery's capacity, the memory effect can reduce the actual capacity
even if the battery is charged for the recommended amount of time.
Prohibited
Do not throw a Ni-cad battery into a fire. Do not disassemble or attempt to repair a Nicad battery pack.
Overheating, damage and acid leakage may lead to burns, loss of eye sight as well as
numerous other types of injuries. The electrolyte in Ni-cad batteries is a strong alkali.
Should you get even the smallest amount of the electrolyte in your eyes, Do Not rub,
wash immediately with water, and seek medical attention at once. The electrolyte can
cause blindness. If electrolyte comes in contact with your skin or clothes, wash with
water immediately.
Caution
Do not store your R/C system where it will be exposed to the following conditions.
• Extreme heat or coldness
• Exposed to direct sunlight
• Where humidity is high
• Where vibration is prevalent
• Where dust is prevalent
• Where there is steam and condensation
• Where the system would be exposed to engine exhaust
Storing your R/C system under adverse conditions could cause deformation and numerous other problems with operation.
(When using a Ni-cad battery to power your system)
Caution
When disposing Ni-cad batteries, cover any exposed contacts with some type of insulation to prevent short circuit.
Improper disposal could cause fire.
Safety Precautions
Prohibited
Other Safety Precautions
Caution
When operating two or more models at the same time, have a third person act as a
spotter. They will be in charge of safety and you should follow their instructions.
Beginners should receive instructions regarding safety and operation from an experienced modeler.
Use genuine Futaba parts only.
Always use only genuine Futaba receivers, servos, and electronic speed controls,
along with other optional parts and components.
Futaba will not be held responsible for damages caused by other than genuine Futaba
parts and components. Use only genuine Futaba parts and components listed in the
instruction manual and catalog.
(When using a Ni-cad battery to power your system)
Prohibited
Do not short circuit the Ni-cad battery terminals.
Short circuiting the terminals will lead to sparks and overheating and could cause a fire
and burns as well.
Before Operation
System Contents
After opening the container, check the contents for the following items. The contents will
vary with the system purchased.
2PL-FM System Contents
Transmitter
T2PL-FM (x1)
Receiver
R153F (x1)
Before Operation
S3003 (x2)
Servo
S3003 (x1)
MC230CR (x1)
or MC330CR (x1)
E.S.C.
SSW-GS (x1)
Switch
Servo mounting hardware and servo horns
Miscellaneous
Mini Screwdriver
Should any item be missing or you are uncertain of the contents of the system, please
contact the dealer where the unit was purchased.
Receiver R153F
Servo S3003
Servo Horn
Crystal
Output Connector
"1" : Steering Servo
"2" : Throttle Servo
Power Supply Connector (B)
To Receiver
Mounting Flange
Nomenclature / Handling
Transmitter T2PL-FM
Throttle Trim Lever (DT2)
Antenna
(*1)
(*1)
Steering Trim Lever (DT1)
Adjusts the throttle in small increments so the
model will not move at neutral.
Adjusts the steering in small increments so
the model will run straight.
Select Button (SELECT)
Press the Select button to select the
desired function screen.
Power Switch
When slid upward,
the power is turned on.
Steering Wheel
LCD screen
Throttle Trigger
(Initial screen)
•Model memory number display
•Battery voltage display
Control the speed of the model and movement
forward and backward.
Steering Dual Rate Lever (D/R)
Grip Handle
(*1)
Adjust the vihicle's steering sensitivity across
the entire range.
Before Operation
Turn model to left or right.
Power switch turned on: Beep confirmation
sound is generated and the model name is
displayed for about two seconds and then
the initial screen appears.
(*1)
Digital trim DT1, DT2, and D/R operation
Push the lever to the left or right (up or down).
The current position is displayed on the LCD screen for about two seconds.
Each step is indicated by a tone. When the trim exceeds the maximum trim
adjustment range, the beep tone will change and the servo will not move
any further. Remember, the trims are digital so the position of each trim is
remembered for each model separately.
Applicable motors (Number of turns is criteria.)
E.S.C. MC230CR
/ MC330CR
•Use the MC230CR with a motor with 20T or more turns.
•Use the MC330CR with a motor with 13T or more turns.
*If a motor with a number of turns smaller than the above is used, the heat
protector and overcurrent protection circuit may operate. The number of turns
of the motor is a criteria only. Depending on the running conditions, the
protection circuit may operate even if the condition above is satisfied.
(Orange)
Checker LED
(Blue)
Pushbutton
switch
(Black)
Motor connector
Connects to the motor.
(Orange) is positive. (Blue) is negative.
If the motor rotates in the wrong
direction, interchange the connections of
this connector.
Nicd battery connector
Connects to the running Nicd battery.
(Red) is positive. (Black) is negative.
(Red)
Nicd battery 6~7 cells (7.2~8.4V)
MC230CR
Receiver connector
Connects to the receiver throttle channel.
Miniature screwdriver
Power switch
Accessory. Use to press the
pushbutton switch.
Handling Procedure for Batteries (8 AA Size Batteries)
(Battery Replacement Method)
1 Remove the battery cover from the
transmitter by sliding it in the direction of the arrow in the figure.
2 Remove the used batteries.
3 Load the new AA size batteries . Pay
Caution
Always be sure you reinsert the batteries in the correct polarity order.
If the batteries are loaded incorrectly , the
transmitter may be damaged.
When the transmitter will not be
used for any short or long period of
time, always remove the batteries.
If the batteries do happen to leak , clean the
battery case and contacts thoroughly. Make
sure the contacts are free of corrosion.
very close attention to the polarity
markings and reinsert accordingly.
Before Operation
4 Slide the battery cover back onto the
case.
Check:
Turn the power switch on the transmitter to the ON position. Check the
battery voltage display on the LCD
screen.
If the voltage is low, check the batteries for insufficient contact in the case
or incorrect battery polarity.
Low Battery Alarm:
If the transmitter battery voltage
drops below 8.5V an alarm will sound
and "LOW" will be displayed on the
LCD screen.
The low battery alarm is meant to be a
safety feature only. Do NOT operate
your radio below 9V. Always shut
your radio off as soon as possible after the low battery warning tone to
avoid loss of control.
Assembly / Adjustment
Receiver and Servo Connection
As you connect the receiver, servos and other components, do so in accordance with the
"Assembly Precautions".
Connections when a E.S.C. MC230CR or MC330CR are used.
Connects to Motor
Connects to Battery
E.S.C.
Steering Servo
Power Switch
Gas Powered Model
Steering Servo
Receiver
Throttle Servo
To Receiver
Battery
Assembly / Adjustment
Receiver
Power Switch
Assembly Precautions
Warning
Check
Check the receiver, servos, and battery connectors, to be sure they are firmly connected.
If a connector is not fully inserted, vibration may cause the connector to work loose
while the model is operating. This will result in loss of control.
Check
Operate each servo horn over its full stroke and check to see that the linkage does not
bind or is not too loose.
Excessive force applied to the servo horn by binding or poor installation may lead to
servo problems and result in loss of control.
Prohibited
The receiver antenna may seem long. Do not cut or alter from the original length.
If the receiver antenna length is altered, the receiver will be adversely effected. The
receiver will become considerably more susceptible to interference and high frequency noise which will result in loss of range and control.
Installation Note
(Electric Cars and Boats)
Isolate the receiver from vibration by attaching to the chassis or mounting plate with
thick double sided tape.
(Gas Powered Cars and Boats)
Isolate the receiver from vibration by wrapping it in foam rubber or similar type cushioning material. Protect the unit from water damage by placing it in a plastic bag or
waterproof radio box.
The receiver contains precision electronic parts. These parts are vulnerable to vibration and shock. Any contact with moisture (water or condensation) may cause receiver
malfunction and loss of control.
Installation Note
Keep all devises that omit high frequency noise, such as motors, batteries, and wiring
that handles heavy current loads, at least 1/2 inch away from the receiver and the
receiver antenna.
High frequency noise will cause a decrease in operating range and could cause loss of
control.
Use genuine Futaba parts only.
Assembly / Adjustment
Use only genuine Futaba crystal sets as specified in this instruction manual.
The use of other than Futaba crystal sets will result in decrease of range as well as
loss of control. There are separate crystals for the Transmitter and Receiver. There
are also crystal sets for AM, FM and Dual Conversion FM. Use only single conversion
FM crystal sets with this system.
Changing crystals in 72-75 MHz transmitter is illegal. However, 27 MHz is allowable. (For U.S.A.)
Install electronic speed control heat sinks as well as other components that conduct
electricity so they can not come in contact with aluminum, carbon fiber or other materials that conduct electricity.
If, for example, the speed control came loose while the model was running and
touched an aluminum chassis, a short circuit may occur that would cause irreparable
damage to the system as well as loss of control.
Installation Note
Noise suppression capacitors should be installed on almost all motors.
If the proper capacitors are not installed, high frequency noise will reduce range and
cause loss of control along with various other problems.
Installation Note
Inspect all linkage installations and any point where metal could come in contact with
other metal parts. Make sure these parts do not touch other metal parts under vibration.
Should a linkage or other metal parts come in contact with other metal parts under
vibration, the high frequency noise generated by this contact will cause interference
and possible loss of control.
Caution
Disassembly Prohibited
Do Not disassemble any part of this system that is not specified in the instruction
manual.
Futaba will not be responsible for any damage due to improper disassembly of any
part of the radio control system.
10
Transmitter Set-Up Procedures
*When making these settings adjustments, do so with the motor disconnected
or the engine not running.
(Preparations)
Select the model memory that is not used and reset it to the initial values with the model selection and
Model Selection
Model Reset
model reset functions.
Model number
（1 - 0）
Model name
(Selection key)
Push the DT2 lever up or down
for about one second.
All data stored in the current
selected model memory is
erased.
Servo Horn Installation Instructions.
1 Connect the receiver, servos, and other components and
then turn on the power switches to transmitter and receiver.
*Both servos will move to the neutral position.
2 At this time install the servo horn in the manner described in
the instruction manual provided with the model this system
will be used in.
NOR: Normal
REV: Reverse
Should the servo operate in the opposite direction required for your application, reverse the direction with the
servo reversing.
(Selection key)
Throttle Servo Reverse
NOR: Normal
REV: Reverse
(Selection key)
E.S.C. MC230CR / MC330CR
NEUTRAL, HIGH, AND BRAKE MAX POINTS SETTINGS
Set the steering angle adjustment function (ATV) to
100% and the ABS function and acceleration function
to OFF using the transmitter throttle channel function.
If the steering angle is too large or the ABS and acceleration
functions are on, erroneous operation may occur.
*When using the ABS function, after setting up
the MC230CR / MC330CR, stop the reverse
function, then turn on the ABS function. If the
ABS function is on, the MC230CR / MC330CR
cannot be set up correctly.
Assembly / Adjustment
Steering Servo Reverse
Reversing The Servo Operation Direction
Before setting each point, set the transmitter throttle channel trim to neutral.
Turn on the power in transmitter -> amp order.
Transmitter throttle operation
MC230CR /MC330CR
(Pushbutton switch operation)
(Checker LED)
Neutral
point setting
･Continuous single blink
･Neutral state
･Press the pushbutton switch.
(0.5 secs or longer)
(Confirmation beep sounds)
High point
setting
･Continuous double blink
･Full high state
(Confirmation beep sounds)
Full High
･Press the pushbutton switch.
Brake MAX
point setting
･Full brake state
Full brake
･Press the pushbutton switch.
･If the LED goes out,
setting is complete.
If the LED does not go off
but blinks rapidly, setting
was not performed
normally. Repeat setting
from "Neutral point
setting".
(Confirmation beep sounds.)
* Since the data is read at the end of setting of all points, the points cannot be set independently.
* If the amp power was turned off during setting, the setting points cannot be memorized. (The previous settings are retained.)
* The confirmation beep sounds only when the motor was connected.
･Continuous rapid blink
11
Description of 2PL-FM Functions
Steering Trim (TRM-CH1)
Steering neutral adjustments can be made by moving the Steering trim knob to the left or right.
Racers Tip
When you install a servo, always check to be sure the
servo is at its neutral position. Adjust the servo horn hole
position and linkage so both are parallel. When a servo
saver is used, place it as close to center position as possible. Be sure the steering trim on the transmitter is at the
neutral position.
Trim Operation And Maximum Travel
Changing the trim can affect the overall settings. When
adjustments are made with the trims, recheck your installation for maximum travel. (Steering EPA right side and left
side).
When Trim usage is extreme
If it takes most of your trim movement to get a servo to the
neutral position, reposition the servo horn or servo saver on
the servo and inspect your linkage installation.
Description of 2PL-FM Functions
12
Steering Trim
（L25 - 0 - R25）
Servo Saver
Direct Servo Saver Horn
90°
Parallel
Throttle Trim (TRM-CH2)
Throttle neutral adjustments can be made moving the throttle
trim to the left or right.
Racers Tip
When using an electronic speed control, set the throttle
trim to neutral and make adjustments to the speed control.
On a gas powered model, set the trim to neutral and adjust
the linkage to the point where the carburetor is fully closed
in accordance with the engine instruction manual.
Trim Operation and Travel
Trim adjustments will affect the overall servo travel.
Check the brake side (backward) movement when changes
are made.
When trim movement is extreme
If you use most of the trim movement to get the servo to the
neutral position , recenter the servo horn closer to the neutral
position and inspect your throttle linkage.
Throttle Trim
（B25 - 0 - F25）
Carburetor Fully Closed
(Drum Type)
(Slide Type)
90°
Steering Dual Rates (D/R-CH1)
Use this function to adjust the steering travel of your model.
If the model understeers (push) while cornering, add steering
by pressing the upper side of the D/R button. When the
model oversteers (loose), take away steering by pressing the
lower side of the D/R button.
Steering D/R
（30 - 100%）
Model Selection/Model Reset (MDL)
The model selection selects the desired model memory from the 10 model memories
stored within the transmitter and the model reset erases all data stored in a specific model
memory.
Model Selection
Model Reset
Model number
（1 - 0）
Model name
(Selection key)
Push the DT2 lever up or down
for about one second.
All data stored in the current
selected model memory is
erased.
This function reverses the rotation direction of
the Steering servo.
Steering Servo Reverse
NOR: Normal
REV: Reverse
When the trim position deviates from
the center, the deviation will be on the
opposite side when the servo is reversed.
(Selection key)
Throttle Servo Reversing (REV-CH2)
This function reverses the rotation direction of
the throttle servo.
When the trim position deviates from
the center, the deviation will be on the
opposite side when the servo is reversed.
Throttle Servo Reverse
NOR: Normal
REV: Reverse
(Selection key)
Description of 2PL-FM Functions
Steering Servo Reversing (REV-CH1)
13
Steering End Point Adjustment (EPA-CH1)
Use this function to limit the servo
movement to the left or right. The
servo travel to each side can be independently adjusted. This feature
will compensate for any difference
in right or left turning angles or radius due to the characteristics of
your model.
Warning
Steering EPA
Range: 0 - 120%
(Left side)
(Right side)
Adjust the travel of the servo
while operating the steering
wheel each way.
Be sure that the steering linkage does not bind or come in
contact with any suspension parts or arms.
If unreasonable force is applied to the servo, the servo may be damaged and result in loss of control.
Throttle End Point Adjustment (EPA-CH2)
This function is used to adjust the
forward and brake side servo
travel. Each direction can be
adjusted independent of each
other. Use this feature to set the
throttle servo travel.
Description of 2PL-FM Functions
14
Warning
Throttle EPA
Range: 0 - 120%
Adjust the travel of the servo
while operating the throttle
trigger each way.
(Forward side)
(Brake side)
Be sure that your throttle linkage does not apply excessive force
to the servo.
If your linkage installation causes an unreasonable amount of force to
be applied to the servo, the servo may be damaged and result in loss
of control.
ABS function (ABS-CH2)
This function simulates a full size
ABS function
ABS Cycle Speed
car's antilock braking by pulsing
OFF: Inhibited
FST: Active (fast)
the brake on and off rapidly.
MID: Active (middle)
(Selection key)
Model stops as rapidly as possible
SLW: Active (slow)
without skidding.
•The cycle speed can be selected from FST/MID/SLW.
Model Name (NAME)
This function provides a 3-character name for each of the model
memories in the transmitter to
easily select the correct setup for
the model currently in use.
•Clearly label each model for easy
selection.
Model Name
Model number
（1 - 0）
Model name
(Selection key)
(Selection key)
MC230CR / MC330CR
CANCELLING THE REVERSE FUNCTION
The amp reverse function can be cancelled by the following method so that the model can be used even in races
that prohibit reverse running. (Brake operation only)
MC230CR / MC330CR
(Pushbutton switch operation)
(Power switch)
Reverse
function
cancellation
While pressing
the pushbutton switch,
ON
set the power switch to ON.
* When desired, you can enable the cancelled reverse
function by repeating the operation shown at the left.
(The reverse function is switched alternately.)
BRAKE/REVERSE OPERATING INSTRUCTIONS
Operation can be switched to reverse operation by returning the throttle trigger (or throttle stick) from the brake
position to the neutral position.
PROTECTION CIRCUIT OPERATION
The following protection circuits are built into the MC230CR / MC330CR. When a protection circuit operates,
remove the cause before operating the model again.
When an overcurrent flows due to an output short circuit, etc., the overcurrent protection circuit automatically
limits the current to protect the FET.
Overcurrent
protection
Remove the cause of the short circuit, etc. before operating the model again.
When abnormal heating of the FET due to an overload, etc. is detected, the heat protector operates so that
the speed is gradually reduced.
When the FET temperature drops, the heat protector automatically resets. However, remove the cause
of the overheating before operating the model again.
Heat protector
When the Nicd battery voltage drops, this function limits the motor output current and ensures steering operation.
Low voltage
operation
After the speed drops, immediately recover the vehicle.
CHECKER LED DISPLAY
The amp operates linearly in proportion to the amount of forward, reverse, and brake operation. The amp operating
state can be checked with the checker LED as shown below.
Checker LED display
(Reverse operation set)
Single blink
(Single confirmation beep)
Amp power ON
(Only brake operation set)
Double blink
(Two confirmation beeps)
High point
Forward
Neutral point
Off
On
Off
Reverse
/brake
On
Brake MAX point
Off
(Amp power left on alarm)
When the transmitter power
was turned off first.
*Becomes brighter nearer the high
point.
*Becomes brighter nearer the
brake MAX point.
Blinks. (Confirmation
beep also sounds.)
Description of 2PL-FM Functions
Operation
*Not used with PCM receivers.
*When the transmitter is OFF, this function is
not performed in environments such that the
servo operates erroneously. Not sure what
this is supposed to mean in yellow.
* Confirmation beep only sounds when the motor was connected.
15
Flow Chart of 2PL-FM Functions
Power switch turned on
Digital trim DT1, DT2, and D/R display
The current position is displayed on the LCD screen for about two seconds
when each digital trim is operated.
Steering Trim
Throttle Trim
(L25 - 0 - R25)
(B25 - 0 - F25)
Steering D/R
The current model name
is displayed for about
two seconds.
(30 - 100%)
(Initial Screen)
Flow Chart of 2PL-FM Functions
•Press the select button to select the desired function screen.
•Press it for about two seconds to return to the initial screen.
Model Selection
Model Reset
Model number
(1 - 0)
Model name
(Selection key)
Push the DT2 lever up or down
for about one second.
All data stored in the current
selected model memory is
erased.
Steering Servo Reverse
NOR: Normal
REV: Reverse
(Selection key)
•DT1 and DT2 operate only
as the data input keys in
the programming mode.
These do not operate as
the trim levers.
Throttle Servo Reverse
NOR: Normal
REV: Reverse
(Selection key)
16
Steering EPA
Range: 0 - 120%
(Left side)
(Right side)
Adjust the travel of the servo
while operating the steering
wheel each way.
Range: 0 - 120%
Adjust the travel of the servo
while operating the throttle
trigger each way.
(Forward side)
(Brake side)
ABS function
ABS Cycle Speed
OFF: Inhibited
FST: Active (fast)
MID: Active (middle)
SLW: Active (slow)
(Selection key)
Model Name
Flow Chart of 2PL-FM Functions
Throttle EPA
Model number
(1 - 0)
Model name
(Selection key)
(Selection key)
To Initial Screen
•Always return to the initial screen after the setting.
17
Reference
*Specifications and ratings are subject to change without prior notice.
Ratings
Transmitter T2PL-FM
Servo
(2 channels, FM transmitter)
Transmitting frequency:
27, 29, 40, 41, 72 or 75 MHz
Modulation method: FM
Power requirement:
12V (penlight battery X 8)
Current drain: 250mA
(standard servo)
Power requirement:
6V (common with receiver)
Current drain: 8mA (at 6V / Idle)
Output torque: 4.1kg-cm (57in.-oz.) at 6V
Operating speed: 0.19sec/60 degree at 6V
Size: 40.4x19.8x36mm (1.59x0.78x1.42in.)
Weight: 37.2g (1.31oz.)
Receiver
R153F
E.S.C.
(3 channels, FM receiver)
Receiving frequency:
27, 29, 40, 41, 72 or 75 MHz
Intermediate frequency: 455kHz
Power requirement: 6V
Current drain: 5mA (at No signal)
Size: 25.6X37.7X14.3mm (1.01x1.48x0.56in.)
Weight: 14.1g (0.50oz.)
Reference
18
S3003
MC230CR / MC330CR
(Electronic speed control)
Operating system: Forward, reverse, and brake
operations are all linear.
Power requirement: Nicd battery 6-7 cells
7.2 to 8.4V
PWM frequency: 1.5kHz (fixed)
Setting: One-touch input by pushbutton switch.
Set data is saved to built-in EEPROM.
Current capacity (FET rating):
Forward=90A/200A, reverse=45A/100A
Size: 27.1x33.3x12.8mm (1.07x1.31x0.50in.)
(excluding protruding parts)
Silicon cord gauge size:
AWG16/AWG14 equivalent
Weight: 44/45g (1.55/1.59oz.)
(including connectors and switches)
BEC voltage: 6.0V
Frequencies (for U.S.A.)
The following frequencies and channel numbers may
be used for surface use in the United States:
75 MHz Band: (car/boat only)
75.410 61 75.610 71 75.810
75.430 62 75.630 72 75.830
75.450 63 75.650 73 75.850
75.470 64 75.670 74 75.870
75.490 65 75.690 75 75.890
75.510 66 75.710 76 75.910
75.530 67 75.730 77 75.930
75.550 68 75.750 78 75.950
75.570 69 75.770 79 75.970
75.590 70 75.790 80 75.990
81
82
83
84
85
86
87
88
89
90
Troubleshooting
If your digital proportional R/C set does not operate, its range is short, it intermittently stops operating, or it operates erroneously, take the action shown in the table
below. If this does not correct the trouble, please contact a Futaba dealer.
Check item
Action
Transmitter/receiver
battery
Dead battery.
Replace the battery. / Charge the Nicd
battery.
Reload the batteries in the correct
polarity.
If the contact spring is deformed,
correct it.
Wipe with a dry cloth.
Incorrect loading.
Faulty contact connection.
Dirty contacts.
Transmitter antenna
Loose.
Not extended to full
length.
Screw in.
Extend fully.
Crystal
Disconnected.
Wrong band.
Different from specification.
Push in.
Match transmitter/receiver band.
Replace with specified crystal.
Connector connection
Incorrect wiring.
Disconnection.
Reinsert.
Push in.
Receiver antenna
Close to other wiring.
Not cut?
Not bundled?
Separate from other wiring.
Request repair.
Install in accordance with instruction
manual.
Servo linkage
Binding or looseness
Adjust at the model side.
Motor
Noise countermeasures.
Install a noise absorbing capacitor.
Reference
Check point
FUTABA CORPORATION
Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan
Phone: (043) 296-5119 Facsimile: (043) 296-5124
©FUTABA CORPORATION
2006, 06
(1)
19

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 20
Creation Date                   : 2006:06:22 17:48:32Z
Mod Date                        : 2006:06:22 17:48:32Z
Producer                        : Acrobat Distiller 5.0.1 for Macintosh
Author                          : morimoto
Create Date                     : 2006:06:22 17:48:32Z
Modify Date                     : 2006:06:22 17:48:32Z
Metadata Date                   : 2006:06:22 17:48:32Z
Creator                         : morimoto
Title                           : 2PL_FM_ENG_0

EXIF Metadata provided by EXIF.tools