Futaba T3PM-24G Radio Control(Transmitter) User Manual 2G Manual

Download:
Mirror Download [FCC.gov]
Document ID	729355
Application ID	vvmxz5tq9N6xnFqqAYDJAA==
Document Description	2G Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	164.52kB (2056547 bits)
Date Submitted	2006-11-16 00:00:00
Date Available	2006-11-16 00:00:00
Creation Date	2006-10-31 09:38:05
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2006-11-15 15:50:14
Document Title	2G Manual
Document Creator	Adobe InDesign CS2_J (4.0.4)

For cars only
1M23N13512
Before using your new 3PM 2.4GHz system, please read this manual thoroughly and use
the system properly and safely. After reading this manual, store it in a safe place.
About this guide
This manual is supplement to the separate "3PM INSTRUCTION MANUAL". Refer to
the "3PM INSTRUCTION MANUAL" for the basic operating instructions. In the programming mode, refer to the programming instructions of the 3PM-FM system.
This guide describes the new functions and the safety precautions of the 3PM 2.4GHz
system.
Thank you for purchasing a 3PM 2.4GHz system. This system is based on the combination of
the newly developed 2.4GHz transmitter and its correspondent receiver. The system utilizes
the 2.4GHz-SS radio communication and an ultra small antenna. In addition, the system
inherits Futaba's unique HRS (High Response System).
3PM 2.4GHz
System
INSTRUCTION MANUAL
Features
• 2.4GHzSS (Spread Spectrum) radio communication system
• Frequency channel setting unnecessary: Sifting the channels within the 2.4GHz band
automatically, this system minimizes the interference from other 2.4GHz system.
• Accepts no unwanted signals by using ID code
• The function “Auto-Detect” is utilized to automatically determine which mode is active,
HRS or PPM mode. (R603FS)
• Short and small antenna (T3PK-2.4G)/Diversity antenna (R603FS)
• No part of this manual may be reproduced in any form without prior permission.                                                      
• The contents of this manual are subject to change without prior notice.
• This manual has been carefully written. Please write to Futaba if you feel that any corrections
or clarifications should be made.
Contents and Technical Specifications
Your 3PM 2.4GHz system includes the following components;
3PM 2.4GHz system
Transmitter
T3PM-2.4G
Receiver
R603FS
Servo
--------
Miscellaneous
Transmitter battery holder
Receiver switch
Mini screwdriver
Instruction manual
[Specification]
• Communication method: One-way operation system
• Mode: PPM, HRS (Auto-detect)
• Maximum operating range: 80m (Optimum condition)
• For safety: F/S, B-F/S, ID (About 4billion ways of pair identifications)
Transmitter T3PM-2.4G;
(Wheel system, 3 channels)
• Transmitting frequency: 2.4GHz band
• Power requirement: (NiCd battery) NT8F700B(9.6V), (Dry cell battery)
Penlight x 8(12V)
• Current drain: 250mA or less
• Transmission antenna: 1/2λ mono-pole
Receiver R603FS;
• Reception antenna: Diversity type (Two antennas: internal and external)
• Power requirement: 6V Nicd battery
• DSC function available
• RS232C port: (for factory use only)
• Size: 39x26x14mm (excluding a projection part)
• Weight: 14.1g
Installing the T3PK-2.4G/R603FS
Install and adjust the T3PK-2.4G transmitter and R603FS receiver as described below.
Adjustment of the antenna direction
(Antenna Moving Range)
 WARNING
the antenna vertically to the ground. Otherwise, the oper Adjust
ating range may become shorter.
Antenna
Receiver installation
LED and
F/S switch
R603FS Receiver
Install the R603FS receiver on the
car as follow;
Note: The operating range may become
shorter, although depending on where
the receiver and the antenna are
mounted.
Antenna
tube
Antenna
 WARNING
Install the antenna in the higher place as
shown in the figure.
 Do not cut the antenna.		
Keep the antenna away from the motor,
 ESC
and other noise sources as pos-
Coaxial
cable
Put the antenna in the antenna tube to
 protect
it.
R603FS
Do not bend the coaxial cable. It causes
 damage.
Wrap the receiver with something soft such as foam rubber to
 avoid
vibration. If there is a chance of getting wet, put the receiver in a waterproof bag or balloon to avoid water.
 CAUTION
Turn on the receiver.
Push the tactile switch of the receiver.
Unrecoverable failure (EEPROM, etc.)
Red : On
Green: On
Green: Blink
Red and Green turn
on alternatively.
How to Set the F/S Position
PPM mode only:
*HRS mode: Set the F/S function by the fail safe function menu.
Move and hold the throttle trigger (stick) to the F/S servo
position where you want to set (slow side) then push the F/S
switch on the transmitter.
Always use R603FS under the following conditions;
Power supply; 6V Nicd battery (PPM/HRS mode)
Servo; 6V type Futaba Digital Servo (HRS mode)
* If the conditions are different, control is impossible or the servo may be damaged.
The LED blinks green.
Note: Always set again when turning on the power.
How to turn on the power
A certain ID number is given to the receiver automatically. Identifying
this ID number, the system will minimize the interference from other
transmitters.
Note: Check the LED of the receiver.
No signal reception
Receiving signals
Receiving signals, but ID is unmatched.
sible as you can.
Note: Check the LED on the rear of the transmitter.
Parameter check for 0.5 seconds after power-on
Red: On
Transmitting signals
Green: On
F/S is activated by the F/S switch of the transmitGreen: Blink
ter. (PPM mode)
Red and Green turn
Unrecoverable failure (EEPROM, etc.)
on alternatively.
Bring the transmitter and the receiver close to each other
within one meter.
Battery F/S function
The Battery F/S function becomes active when the voltage of the
receiver becomes 4.75V or less. The throttle servo move to the preset
F/S position.
Turn on the transmitter.
Usage Precaution
Repair Service
 WARNING
attention should be paid before turning on the system
 Special
while other cars are running or other airplanes are flying because the 2.4GHz RC system could potentially affect them.
 WARNING
 Be sure to set the Fail Safe function.
Special Markings;
Pay special attention to the safety at
the parts of this manual that are
indicated by the following marks.
[Symbol]
; Prohibited
; Mandatory
Mark
Before requesting repair, read this instruction manual again and recheck your
system. Should the problem continue, request repair service as follows:
Describe the problem in as much detail as possible and send it with a detailed
packing list together with the parts that require service.
• Symptom (Including when the problem occurred)
• System(Transmitter, Receiver, Servo's and model numbers)
• Model (Model name)
• Model Numbers and Quantity
• Your Name, Address, and Telephone Number.
If you have any questions regarding this product, please consult your local
hobby dealer or contact the Futaba Service Center.
Meaning
Procedures which may lead to a dangerous condition and cause
death or serious injury to the user if not carried out properly.
Procedures which may lead to a dangerous condition or cause death
or serious injury to the user if not carried out properly, or procedures
where the probability of superficial injury or physical damage is high.
Procedures where the possibility of serious injury to the user is
small, but there is a danger of injury, or physical damage, if not
carried out properly.
FUTABA CORPORATION Phone: (043) 296-5118 Facsimile: (043) 296-5124
Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan
©FUTABA CORPORATION     2006, 10     (1)
INSTRUCTIONS MANUAL
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used according to the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which it found by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet other than the receiver’s
-- Consult the dealer or an experienced radio/TV technician for assistance.
CAUTION:
To assure continued FCC compliance:
(1) Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
FCC Label Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Exposure to Radio Frequency Radiation
To comply with FCC RF exposure compliance requirements, a separation distance of at
least 20cm must be maintained between the antenna of this device and all persons. This
device must not be co-located or operating in conjunction with any other antenna or
transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 3
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:22aef7a0-006e-479f-a156-f9dcbcfe08fa
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2006:10:31 09:38:05+09:00
Metadata Date                   : 2006:11:15 15:50:14+08:00
Modify Date                     : 2006:11:15 15:50:14+08:00
Creator Tool                    : Adobe InDesign CS2_J (4.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 10315 bytes, use -b option to extract)
Instance ID                     : uuid:edcedcc6-4fd8-49c3-b5d5-ce1c41b42d74
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:325e27a1-6326-11db-a6cb-af7c09013bbd
Derived From Instance ID        : 1213d540-3ee7-11db-a268-b9816bfac16e
Derived From Document ID        : adobe:docid:indd:7fff41ac-38a9-11db-aad4-fa5626696aca
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 350.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 350.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:345DD97FC864DB11854581460C0AADE3, uuid:f57603d6-92b0-4b82-9aab-fff8afaafc3b, uuid:c9205810-9b64-4ae3-8a81-f730ffc6d72f, uuid:7cc7ad07-7616-4c06-bc64-64fb2b5618fa, uuid:3e183b0c-37b9-487b-acbc-fc71477eccf5, uuid:cf4bf2a9-6c2d-41ea-90bf-2b55ed9c9511, uuid:5d50cbd5-f6c6-44bf-82fe-8f2081234e16, uuid:bcd26c43-07ba-4ba8-9407-18eabcd23b7e, uuid:6ba44f02-3901-4666-bce3-43ce9b727afd
Manifest Reference Document ID  : uuid:B167011AA064DB11854581460C0AADE3, uuid:4318F002517FDA11862795512BCEB185, uuid:E931518ACE67DB1181428817E4DAA3C8, uuid:EC31518ACE67DB1181428817E4DAA3C8, uuid:0ADB4D0AE937DB11A2E1D8D5917070E9, uuid:96CB0E2FD337DB11A2E1D8D5917070E9, uuid:9735CAE8DC67DB1181428817E4DAA3C8, uuid:6A6C71796C82DA118EA4A7C1B707147C, uuid:c9db27a4-abed-4d53-90e4-444669bcbcda
Format                          : application/pdf
Creator                         : Adobe InDesign CS2_J (4.0.4)

EXIF Metadata provided by EXIF.tools