G4S Monitoring Technologies PID915 OM247 PID3 User Manual User guide 3

G4S Monitoring Technologies Limited OM247 PID3 User guide 3

Contents

User guide 3

Document Classication: Public
OM247-FIT Fitting Tool
& Key Fob Safety Guide
User Safety and Regulations
Page 2Document Classication: Public
This guide contains basic regulatory and safety information.
Document Number: 94-0175-01
Revision: 1.0
Issue Date: 16/06/2014
About This Manual
Page 3Document Classication: Public
Operational Warnings
Important information on safe and efcient operation. Read this information before using
the device. For safe and efcient use of the device, observe the guidelines outlined below.
Environmental Specication
10% to 90% relative humidity
Operational Temperature range -20°C to +60°C
(AC Power Adaptor: RH 20% to 85%, Operating Temperature 0 to 40°C)
Operation
The equipment must be used by a SERVICE PERSON.
Battery Charging (Fitting Tool Only)
When not in use, disconnect the battery charger from both the device and the mains
electricity supply. To halt charging, remove the charging clip from the device.
User Safety
Page 4Document Classication: Public
Do not disassemble, open, crush, deform or puncture the product.
Do not modify, remanufacture, attempt to insert foreign objects, expose to re,
explosion, or any other hazards.
Only use an approved AC power adaptor with the Fitting Tool. Use of an unapproved
charger may present a risk of re, explosion, leakage or other hazard.
Approved AC Power Adaptor
Source: G4SMTL
Model: @3A-181WP06
Part Number: 39-0023-3
Input Rating: 100-240V VAC, 50-60Hz, 600mA
Output Rating: 6VDC, 3A
Product Handling
Page 5Document Classication: Public
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
FCC Statements
Page 6Document Classication: Public
FCC Statements (continued)
Modications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment
under FCC rules.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
These products meet the FCC Radiofrequency Emission
Guidelines and are certied with the FCC as:
FCC ID: 2ACGBFIT915
FCC ID: 2ACGBPID915
The FCC ID is located on a label on the rear face of the
product.
Page 7Document Classication: Public
We hereby declare that these products are in conformance
to all essential requirements of the R&TTE Directive 1999/5/
EC. The products are marked with the ‘CE’ symbol and can be
used throughout the European Community.
This indicates compliance with the R&TTE Directive 1999/5/
EC and meets the relevant parts of the following technical
specications:
EN 301 489-1 v1.6.1:2005
EN 300-220-2 v2.1.1
EU Regulatory Conformance
This symbol indicates that this product should be recycled and
not be disposed of in unsorted municipal waste. This product
should be returned to the supplier for correct disposal.

Navigation menu