G4S Technology S813A S813A Proximity Reader User Manual Manual

G4S Technology Limited S813A Proximity Reader Manual

Manual

Installation and User Instructions for S813 Readers1Mount the Backplate2Reader LinksThe following links are provided on the reader's PCB:LK1 (Audio feedback) - Set to "0" for sound off. Set to "1" for sound on.LK3 (Test) - Ensure that this link has been removed.The S813 is a contactless smart-card reader, with LCD and keypad, which uses p. The S813 is able to read Philips MIFARE and Philips MIFARE DESfire smart cards containing optional biometric data. The reader can simultaneously support both card formats.The reader is automatically configured to accept the first two card formats presented.combined fingerprint and 20mA current loop seudo-random communications® ®NOTE: Correct mounting of the unit is essential. Follow these guidelines carefully.It is important to ensure that people present fingers at the same height, angle and orientation as presented during fingerprint enrollment. Inconsistencies may cause difficulty in gaining access. For best results:·Mount the unit flat against a wall.·The top of the reader must be at a height of 3'7" to 3'11" (1.1m to1.2m) from the floor.·Ensure that desks or other objects do not obstruct easy access to the reader.Mounting the reader:1) Detach the main body of the reader from the backplate by releasing the two securing screws along the bottom edge, swinging the backplate upwards and easing it away from the two top clips.2) Feed the cable and terminal block through the backplate, then screw the backplate to the wall using the holes provided.
9600-0306. Installation and User Instructions for S813 Readers, Issue 1.4.1 4th December 2009. G4S Technology, 2009. G4S Technology Limited cannot be held liable for technical and editorial omissions or errors made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of this material. All trademarks acknowledged.FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any unauthorized modification to this device may void the ©5Using the Reader3Reader ConnectionsSpecificationsInput: 310mA max @ 10-14Vdc.Operating temperature: 32 to 122 F (0 to 50 C). Operating humidity: 15 to 90%, non-condensing.Maximum read range: 1" (25mm).Approvals: EN50133, R&TTE, IP605.For internal use only.° °Present the proximity card face-on close to the reader underneath the finger pad until you hear a "bleep". (No bleep is given if the audio feedback link, LK1, is in the "0" position.)After presenting your card, you may be prompted to enter a PIN and/or place your finger on the finger pad. Follow the on-screen instructions. For DESfire cards, you may also be prompted for a "CARD PIN". If so, enter the DESfire card PIN, then press "#" if the PIN has fewer than eight digits.The system can be set up to generate a "duress" transaction if the pre-defined duress finger is placed on the pad. In two-finger mode, the duress finger must be placed first. The I/O terminal is for connection to a RIM - see the Installation Instructions for S660 Remote Interface Module (RIM).If the reader needs to read both MIFARE and MIFARE DESfire cards, make sure that one of each card is presented to the reader immediately after the reader has been installed and the cards have been encoded in the Admin/Card Holders screen of the SMS software. The reader supports the first two card formats presented. If the two cards are the same type, only one format is supported.A reader Setup menu can be displayed by pressing the * and # keys simultaneously while power is applied. You can use the menu to change the language used for the LCD (default English), and view the two card types/formats previously programmed. At the prompts, press * for No and # for Yes. 4Reader Configuration0VConnect shield at controllerend only (attach to case). RX+RX-TX+TX-12V ReaderTwisted pairs (useBelden 9503 cable) Controllerconnections (20mA current loop) 0VTX+Do not useTX-I/0RX+RX-+VIT IS ESSENTIAL TO PLACE EACH FINGER FLAT AND STRAIGHT ON TO THE SENSOR.Slide your finger into place, so that your finger makes contact with the ridge lock before the sensor. The first joint of your finger must rest on the ridge lock.For further details of using this reader, refer to the 813 Fingerprint Reader User's Guide.INCORRECTûCORRECTüRidge lock

Navigation menu