G4S Technology S849 S849 Inductive Reader User Manual 9600 0531 Issue 1 0 s849 In

G4S Technology Limited S849 Inductive Reader 9600 0531 Issue 1 0 s849 In

manual

Installation and User Instructions for S849 ReadersYou should find that thebackplate has holes forconnection to moststandard electricalbackboxes.With the backplate off (see above), mountthe backplate adjacent to the opening edgeof the door and at a convenient height. Feedthe required cables through the backplate:The cable from the controller.The cable from the heater, if used (mustbe a separate cable).!!2The optional heater kit maintains the reader atthe correct temperature when mounted outside.With the backplate off, remove the backing paperfrom the two elements, then stick them to theinner sides of the reader. The heaters must beconnected to a 24V AC supply (min 25VA).When mounting outside, the two-part gasket kitmust be fitted:a) Remove the backplate from the reader byreleasing the two securing screws.b) Remove the cutouts and backing paperfrom the two gaskets, then stick them to thebackplate as shown.Outer gasketInnergasketBackplatesecuring screwsBackplate1Fit the Weatherproofing KitMount the BackplateThe S849 is a contactless smart-card reader with keypad.The S849 is able to read ISO14443 type A, PhilipsMIFARE Classic, MIFARE Ultra Light and MIFARE DESfiresmart cards, and provides the option to use Wiegand orpFor either type of card, the S848 supports the use ofunencoded cards (where only the unique card serial numberis read), or cards encoded with a card number. Severalencoding formats are supported.The reader can simultaneously support two different cardtypes/formats (e.g. non-encoded MIFARE and smartMAX-encoded MIFARE DESfire, or non-encoded MIFARE andsmartMAX-encoded MIFARE). The reader is automaticallyconfigured to accept the first two card types/formatspresented.®®20mA current loop seudo-random communications.
SpecificationsInput voltage: 10.2-14Vdc.Input current (excl. heater): 100mA @ nom. 12Vdc.Operating temperature: -13 to 158 F (-25 to 70 C)without heater.Operating humidity: 15 to 90%, non-condensing.Maximum read range: 5" (125mm).Approvals: EN300330, EN301489°°5Using the Reader4Reader Connections9600-0531. Installation and User Instructions for S849 Readers,Issue 1.0 16th Decemmber 2009. G4S Technology, 2009.All trademarks acknowledged. HID is a registered trademark of HIDCorporation.FCC Notice: This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) this device must acceptany interference received, including interference that may causeundesired operation.Any unauthorized modification to this device may void the authority ofthe user to operate it.©Present the card face-on to the reader until you hear "bleep". Cards can be presented in rapidsuccession; there is no need to wait for the green or red LED to extinguish efore presenting another.abIf the reader has been enabled for user-code mode at the controller, you can gain access by pressingthe # key, entering your card number, then pressing the * key.If the amber LED flashes, enter your PIN. If you make amistake, the red LED is lit for a moment, then the flashingamber prompts you to try again.These auxiliary LED indicators can be configured tooperate in conjunction with conditional commands.When this LED is lit, the lock is released and you mayopen the door.Green (accessgranted) LEDRed (accessdenied) LEDFlashing amber(PIN) LEDAlarm LEDSwitch LEDThis is lit if you do not have access rights to gain entry, orif the reader could not read your card (in this case, movethe card away, then present it again).About the Reader LEDs}Connect shield atcontroller end only(attach to case)TX-ReaderTwisted pairs(use Belden)TX+0VTX-RX+RX-+VDo not useDo not useDo not useDo not use12VdcTX+RX+RX-0VNote: To configure thereader as a 20mA reader,connect the jumperacross the center and"C/L" pins of LK1.WE C/LCurrent Loop Reader Connections12VdcConnect shield atcontroller end only(attach to case)Apply 0V toactivate door-GreenRedData 0Data 10VReaderGn0V0sDo not useDo not+VBz1sDo not useRdNote: To configure thereader as a Wiegandreader, connect thejumper across the centerand "WE" pins of LK1.WE C/LWiegand Reader Connections

Navigation menu