G4S Technology S853 RFID Tag Reader User Manual

Download:
Mirror Download [FCC.gov]
Document ID	496365
Application ID	g9cTXdP1XgwfR5Em0fjY5g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.15kB (314396 bits)
Date Submitted	2004-12-14 00:00:00
Date Available	2004-12-14 00:00:00
Creation Date	2004-07-26 17:32:27
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2004-08-05 10:41:00
Document Title	C:\Group4\PDF folder\Drafts waiting for approval\s853 Installation Instructions.eps
Document Creator	CorelDRAW(TM) Classic

Installation and User Instructions for S853 Readers
The S853 is a combined contact and contactless smartcard reader, with LCD and keypad, which uses 20mA
current loop pseudo-random communications. The S853 is
®
®
able to read Philips MIFARE and Philips MIFARE DESfire
smart cards.
For either type of card, the S853 supports the use of
unencoded cards (where only the unique card serial
number is read), or cards encoded with a card number.
Several encoding formats are supported.
The reader can simultaneously support two different card
types/formats (e.g. non-encoded MIFARE and smartMAXencoded MIFARE DESfire, or non-encoded MIFARE and
smartMAX-encoded MIFARE). The reader is automatically
configured to accept the first two contactless and the first
contact card types/formats presented.
Fit the Weatherproofing Kit
When mounting outside, the two-part gasket kit
must be fitted:
a) Remove the backplate from the reader by
releasing the two securing screws.
b) Remove the cutouts and backing paper
from the two gaskets, then stick them to the
backplate as shown.
Outer gasket
Backplate
Inner
gasket
The optional heater kit maintains the reader at
the correct temperature when mounted outside.
With the backplate off, remove the backing paper
from the two elements, then stick them to the
inner sides of the reader. The heaters must be
connected to a 24V AC supply (min 25VA).
Mount the Backplate
With the backplate off (see above), mount
the backplate adjacent to the opening edge
of the door and at a convenient height. Feed
the required cables through the backplate:
! The cable from the controller.
! The cable from the heater, if used (must
be a separate cable).
! A cable from a Remote Interface Module
(RIM), if used. A RIM can reduce cable
lengths to door furniture.
Backplate
securing screws
You should find that the
backplate has holes for
connection to most
standard electrical
backboxes.
Reader Links
Ensure no jumpers are fitted across LK2 (TEST) and LK3 (NODE TERM) and LK4 (HGU TERM). If a
jumper is provided, park it across one pin only. LK1 (USER FB) - set to 1 for sound on and 0 for sound off.
4
Reader Connections
Reader
12V
Controller
connections
(20mA current
loop)
+V
0V
TX-
RXRX+
I/0
TXTX+
Do not use
TX+
RXRX+
Connect shield at controller
end only (attach to case).
The I/O terminal is for
connection to a RIM (see
the RIM Instructions).
On completion, re-secure
the reader to the backplate.
Twisted pairs (use
Belden 9503 cable)
0V
Reader Configuration
The reader supports the first two contactless and the first contact card types/formats presented after
power-up. For example, encoded MIFARE and encoded MIFARE DESfire (in this example, unencoded
cards would not be recognized). The reader enters this configuration mode whenever power is re-applied.
A reader Setup menu can be displayed by pressing the * and # keys simultaneously while power is
applied. You can use the menu to change the contrast and language used for the LCD (default English),
and view/clear the three card types/formats programmed. At the prompts, press * for No and # for Yes.
Using the Reader
For a contactless card, present the card face-on to the reader until you hear "bleep". For a contact card,
insert the card (chip upwards and facing you) into the slot at the bottom of the reader until you hear a
"bleep". Cards can be presented in rapid succession; there is no need, for example, to wait for
"UNLOCKED" to disappear before presenting another.
If the reader has been enabled for user-code mode at the controller, you can gain access by pressing
the # key, entering your card number, then pressing the * key.
About the Reader Messages
READY – The reader is waiting for a valid card to be presented.
UNLOCKED – The lock is released and you may open the door.
ACCESS DENIED & LOCKED – You do not have access rights to gain entry, or the reader
did not read your card properly (in this case, present it again).
ENTER PIN – Enter your PIN. If you make a mistake, the message INCORRECT PIN is
momentarily displayed, followed by ENTER PIN, to prompt you to try again.
CARD PIN AND # – Enter the DESfire card PIN, then press # if the PIN is less than 8 digits.
(Flashing or steady) – These auxiliary indicators can be configured to operate in
conjunction with conditional commands.
9600-0348. Installation and User Instructions for S853 Readers,
Issue 1.0 5th August 2004. ©Group 4 Technology, 2004.
FCC Notice: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Any unauthorized modification to this device may void the authority of
the user to operate it. All trademarks acknowledged. Philips and
MIFARE are registered trademarks of Philips Electronics N.V.
Specifications
Input voltage: 9-14Vdc.
Input current (excl. heater): 195mA @ nom. 12Vdc.
Operating temperature: -4 to 158°F (-20 to 70°C)
without heater.
Operating humidity: 15 to 90%, non-condensing.
Max. read range (MIFARE DESfire): 1.2" (30mm).
Approvals: EN50133, R&TTE, IP656.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:07:26 17:32:27
Producer                        : Acrobat Distiller 4.05 for Windows
Creator                         : CorelDRAW(TM) Classic
Title                           : C:\Group4\PDF folder\Drafts waiting for approval\s853 Installation Instructions.eps
Modify Date                     : 2004:08:05 10:41:00+01:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools