G4S Technology S884A S884A Proximity Reader User Manual manual

Download:
Mirror Download [FCC.gov]
Document ID	1447749
Application ID	DLGyQ6V9NbepKDHc99JmUA==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.24kB (228047 bits)
Date Submitted	2011-04-13 00:00:00
Date Available	2011-04-13 00:00:00
Creation Date	2011-03-17 15:09:47
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2011-03-17 15:09:47
Document Title	9600-0537 Issue 1.0- S884 Installation and User Instruction
Document Creator	CorelDRAW
Document Author:	Watts, Andrew

Installation and User Instructions for S884 Readers
The S884 is a contactless smart-card reader, with Graphic LCD
and keypad. The reader can be set to use Wiegand or 20mA
current loop communications.
The S884 reader will read smartMAX encoded MIFARE cards
and card serial numbers from most ISO 14443A smart cards
which have a 4-byte UID (User Identification). The reader may
be configured to read other card types by presenting a
programming card to the reader during start up.
Mount the Backplate
Mount the backplate using countersunk headed screws
adjacent to the opening edge of the door and at a
convenient height (recommended height is 5' (1.5m) to top
of unit).
If fixing hole ’A’ is used then the breakout must be removed
and the screw must not protrude.
Feed the required cables through the backplate:
·
The cable from the controller.
You should find that
B the backplate has
·
A cable from a External Reader (Optional).
holes for connection
to most standard
·
General Purpose Input / Output cable (Optional)
electrical backboxes.
If wall tamper function is to be used then breakout ‘B’ must
be removed and an appropriate wall screw fitted through
the hole to actuate the tamper lever.
The securing screws ‘C’ are integral to the backplate and are unscrewed via the small holes in the
enclosure so that the screw heads locate in the counterbored holes on the inside of the
enclosure.
Reader Connections
20mA current loop
Twisted pairs (use
Belden 9503 Cables)
0V
Connect shield at
controller end
only.
Use Belden
9537 Cable
0V
TX+
TX-
RX+
RX-
RX+
RX-
TX+
TX12V
+V
Reader
TB1
Wiegand
Controller
Connect shield
at controller end
only.
0V
RED
GRN
+V
Reader
TB1
Note: Use LK2 to select the communications mode (See Step 3).
0V
Red
Green
Data 0
Data 1
12V
Controller
3 Reader Links
Set LK2 (COMMS) across the center and W pin for Wiegand communications, or across the center and C
pin for 20mA current loop communications. Set LK3 (USER Keypad audio feedback) to 1 for sound on, or
0 for sound off. Set LK4 (EXT RDR) across the center and W pin for Wiegand communications, or across
the center and M pin for Magstripe Reader communications.
4 External Reader Connections (Optional)
The reader is connected to the controller using the 20mA current loop scheme shown in section 2 and, in
addition, the external reader is connected as shown below.
Magstripe
Data
1/DA
12V
+V
Reader
TB1
0V
0s
0V
0/CK
1s
1/DA
12V
+V
Wiegand Reader
0V
0/CK
Magstripe Reader
Wiegand
0V
Clock
Reader
TB1
Note: Use LK4 to select the External Reader type (See Step 3).
5 General Purpose Inputs & Outputs (Optional)
I/O Connections
IN 1
IN 2
COM
NC
NO
SPKR
SPKR
Reader
TB2
Using the Reader
Present the card face-on to the reader until you hear a "bleep". Cards can be presented in rapid succession;
there is no need, for example, to wait for "UNLOCKED" to disappear before presenting another.
If the reader has been enabled for user-code mode at the controller, you can gain access by pressing the O
key, entering your card number, then pressing the P
key.
LED Status Indicator
GREEN – The lock is released and you may open the door.
RED – You do not have access rights to gain entry, or the reader did not read your card
properly (in this case, present it again).
YELLOW – Enter your PIN. If you make a mistake, the message INVALID PIN is momentarily
displayed, followed by ENTER PIN, to prompt you to try again.
A Setup menu can be displayed by pressing the O
and P
keys simultaneously while power is applied. You
can use the menu to change the contrast and language used for the LCD (default English). Use the four
function keys to navigate around the menu.
9600-0537. Installation and User Instructions for S884 Readers,
Issue 1.0 11th March 2010. © G4S Technology, 2010.
FCC Notice: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Any unauthorized modification to this device may void the authority of
the user to operate it. All trademarks acknowledged.
Specifications
Input voltage: 9-14Vdc.
Input current: 200mA @ nom. 12Vdc.
Operating temperature: 14 to 131°F (-10 to 55°C)
Operating humidity: 15 to 90%, non-condensing.
Maximum read range: 4" (100mm).
Approvals: EN50133, EN302291, EN301489

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Create Date                     : 2011:03:17 15:09:47Z
Modify Date                     : 2011:03:17 15:09:47Z
Producer                        : Corel PDF Engine Version 14.0.0.701
Author                          : Watts, Andrew
Creator                         : CorelDRAW
Title                           : 9600-0537 Issue 1.0- S884 Installation and User Instruction

EXIF Metadata provided by EXIF.tools