GE MDS DS-LN100 Industrial Radio Module User Manual
GE MDS LLC Industrial Radio Module
a href="https://usermanual.wiki/GE-MDS" itemprop="url">
GE MDS >
User Manual
| Download: | |
| Mirror Download [FCC.gov] | |
| Document ID | 3368746 |
| Application ID | 9drSQLOtM6A/i3PFv9G1tA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 74.86kB (935771 bits) |
| Date Submitted | 2017-04-24 00:00:00 |
| Date Available | 2017-04-24 00:00:00 |
| Creation Date | 2017-04-12 08:25:51 |
| Producing Software | Microsoft® Word 2010 |
| Document Lastmod | 2017-04-12 08:25:51 |
| Document Title | User Manual |
| Document Creator | Microsoft® Word 2010 |
| Document Author: | William Yochum |
![MDS LN100 Integrator’s Guide 05-6950A01, revision 3 [1] MDS LN100 Integrator’s Guide 1.0 INTRODUCTION The LN100 (Figure 1), is a fixed location (not intended for mobile use), multi-modem system operating in licensed bands between 150-174, using channel bandwidths of 6.25kHz, 12.5kHz, and 25.0kHz. Modulation choices for each bandwidth include CPFSK, QPSK, 16QAM, and 64QAM. Maximum power and modem speed is based on frequency, modem choice, and applicable emission mask. The unit is designed for use inside data equipment to provide reliable connectivity in wireless networks. The LN100 power control circuit ensures that the RF output is linear and never exceeds +41.4 dBm at the antenna connector. The module is designed for OEM use only. Host systems must be professionally installed. Host systems must be factory configured by the OEM to operate at the correct frequency and output power setting. Refer to the table at the end of this guide to determine applicable antenna types and the RF output power allowed. 1.1 Transceiver Features The LN100 maximizes performance and flexibility in wireless networks, offering the following key features: Selectable frequency (150-174MHz) Selectable bandwidth (6.25kHz, 12.5kHz, 25.0kHz) Selectable modem choices (CPFSK, QPSK, 16QAM, 64QAM) RSSI and EVM readback indicators Store-and-Forward repeater operation Same hardware for Master, Remote, or Store-and-Forward configurations Supports RS/EIA-232(TTL), Ethernet, and USB user interfaces Operates at 5.25 Vdc at the MiniPCIe card edge power connections and 10-60Vdc at the 3-pin power connector. Figure 1. LN100 Transceiver Module (Mini PCI-Express Card Edge for Data/Power/& I/O and J700 Antenna) NOTE: Some features may not be available on all units, based on the options purchased, or regulatory constraints in the country of operation.](https://usermanual.wiki/GE-MDS/DS-LN100/User-Guide-3368746-Page-1.png)
![MDS LN100 Integrator’s Guide 05-6950A01, revision 3 [2] 2.0 INSTALLATION The transceiver is designed for installation in existing electronic equipment. The I/O and 5.25v power connections are made through the Mini PCI-Express card edge. The 10-60v power is provided through a separate 3-pin connector on the bottom of the module. The transceiver mounts to the host heatsink assembly using two #4 screws inside the RF can area. The required heatsink contact area on the bottom surface of the PCB has the solder mask removed for proper heat transfer. Only one cable connection is required to the radio for the J700 Antenna connector. The module has three optionally populated status LEDs (CR100, CR101, and CR1000) that indicate operating mode details. These LEDs provide important information that is useful during startup and optimization of the radio link. Antennas used with the radio can be either a Yagi directional type (often used at remote sites) or an omni-directional type used for short range applications or at Master stations. Contact your sales representative for information on available antennas. Follow these steps to install the transceiver module: 1. Power down the Host assembly the module is being installed in to. 2. Mate the MiniPCIe card edge of the module into the socket on the Host assembly. 3. Secure the module to the heatsink surface using two #4 screws through the mounting holes in the corners of the RF can area on the radio’s PC board. 4. Install the RF shield over the transceiver section. 5. Select and install an appropriate antenna and feedline for your system coverage requirements. 6. Connect the antenna coaxial lead to J700 on the module. It accepts a Type-TNC male coaxial connector. 7. Host Power Supply Requirements: a. Input power applied on the 52-pin connector (J1100) must be a regulated 5.25 Vdc (-/+0.05 V). b. Input power applied on 3-pin connector (J900) must not exceed the range 10.0-60.0Vdc i. Nominal Input power on J900 is in the range 12-52Vdc - FCC CFR 47 2.1055(d)(1) See Table 1 for power supply interface connections. 52-Pin GE MDS NIC Card Edge Pin Description 1, 6, 7, 10, 11, 13, 12, 14, 16, 19, 20, 23, 25, 28, 30, 31, 32, 33, 36, 38, 42, 44, 45, 46, 47, 48, 49, 51 GPIO (Includes Ethernet & Serial) *Consult Factory Documentation for specific details 2, 24, 39, 41, 52 +5.25V 3, 5, 8, 17, 22 NC 4, 9, 15, 18, 21, 26, 27, 29, 34, 35, 37, 40, 43, 50 GND Table 1. LN100 Power Supply Connections 3-Pin GE MDS (J900) connector Pin Description 1 GND 2, 3 +10.0-60.0V](https://usermanual.wiki/GE-MDS/DS-LN100/User-Guide-3368746-Page-2.png)