GE MDS DS-SD2 Wireless Data Transceiver User Manual 4692A SD2 Quick Start FCC

Download:
Mirror Download [FCC.gov]
Document ID	1205395
Application ID	yJJkJ3C37V9R7QqD0f4tNw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.25kB (140602 bits)
Date Submitted	2009-11-25 00:00:00
Date Available	2009-11-25 00:00:00
Creation Date	2007-03-01 15:15:37
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2009-11-12 11:52:22
Document Title	4692A-SD2_Quick_Start_(FCC).fm
Document Creator	FrameMaker 8.0
Document Author:	kcarey

MDS SD2 Transceiver
Quick Start Guide (x710 Mode)
1.0
ANTENNA SYSTEM
Master Stations typically use
omni-directional antenna
INTRODUCTION
The MDS SD2 transceiver (Figure 1) is a software-configurable,
industrial solution for use in wireless telemetry applications. The
unit operates in the 216 to 222 MHz frequency band.
The radio interfaces with a variety of data control equipment such
as remote terminal units (RTUs), programmable logic controllers
(PLCs), flow computers, and similar devices. Data interface connections may be made by both serial (RS-232/485) and limited
Ethernet protocols.
LED INDICATOR
PANEL
TRANSCEIVER
DC POWER SUPPLY
Negative Ground Only
ETHERNET
CONNECTOR (RJ-45)
AL
ER
IN
ED
OS
FE
-L
LO
DC INPUT
POWER
SERIAL DATA
CONNECTORS (DB-9)
COM1 used for radio management
TO
DATA TELEMETRY
DEVICE
ANTENNA
CONNECTOR (TNC)
Figure 2. Typical Installation (Remote Site Shown)
Invisible
place
holder
Figure 1. MDS SD2 Data Transceiver
INSTALLATION
There are three main requirements for installing the transceiver:
• Adequate and stable primary power
• An efficient and properly installed antenna system
• Correct interface connections between the transceiver and
the data device.
Figure 2 shows a typical installation of the radio.
2.75˝ (7 cm)
2.0
NOTE: Retrofit Kits are available to simplify installation at former
MDS x710 digital and analog sites. Consult the Reference Manual for ordering details.
2.1
7.25˝ (16.99 cm)
Installation Steps
In most cases, the steps given here are sufficient to install the
transceiver. Refer to the Reference Manual for additional details,
as required.
1. Mount the transceiver using the brackets supplied. Attach
the brackets to the bottom of the transceiver case (if not
already attached), using the four 6-32 x 1/4 inch (6 mm)
screws supplied. Mounting bracket dimensions are shown in
Figure 3. If DIN Rail mounting brackets are to be used, consult
the Reference Manual.
NOTE: To prevent moisture from entering the radio, do not mount
the case with the cable connectors pointing up. Also,
dress all cables to prevent moisture from running along
the cables and into the radio.
CAUTION: Using screws longer than 1/4 inch (6 mm) to attach the
brackets to the radio may cause internal damage. Use
only the screws supplied.
05-4692A01, Rev. 03 (FCC)
Figure 3. Mounting Bracket Dimensions
2. Install the antenna and feedline. The antenna used with the
radio must be designed to operate in the radio’s frequency
band, and be mounted in a location providing a clear path to
the associated station(s). At Remote sites, aim directional
antennas toward the Master Station. Low loss coaxial feedline
should be used and it should be kept as short as possible.
3. Connect the data equipment. Connection may be made to
the COM port using Serial protocols (RS-232/RS-485).
• Connect your data equipment to the appropriate serial port
on the front panel. (Typically, COM2 is used for connecting
data equipment, and COM1 is used for management of the
radio. Other arrangements are possible. Refer to the Reference Manual for details.) In all cases, the radio is hardwired
as a DCE device. A straight-thru cable may be used for most
applications.
4. Connect primary power. Input power must be 10.0 to 30 Vdc
and capable of providing at least 2.5 Amperes. A power connector with screw-terminals is provided with the unit (see
MDS SD Series Quick Start Guide (x710 Mode)
Figure 4). Strip the wire leads to 6 mm (1/4 inch) and insert
them into the wire ports. Be sure to observe proper polarity as
shown below. Tighten the binding screws securely.
MODEM command. Use MODEM [xxxx] if changes are
required, where xxxx represents the modem speed in bps.
When finished with the steps above, review the other configuration options to determine if other settings are required for
your system. Table 3 lists key software commands for the
radio.
2.2
Figure 4. DC Power Connector
CAUTION: The unit is designed for use with negative-ground
systems only. The power supply should be equipped
with overload protection (NEC Class 2 rating), to
protect against a short circuit between its output terminals and the radio’s power connector.
Initial Checkout
In-service operation of the transceiver is completely automatic.
The only operator actions required are to apply DC power and
observe the LEDS for proper indications. Table 1 summarizes the
radio’s LED functions.
2.2.1
LED Functions
NOTE: LED labeling may vary on early units. LED position and
functionality remains as described below.
5. Set the radio’s configuration. Connect a PC to the radio’s
COM1 port as shown in Figure 5. A straight-thru cable may be
used for this connection.
NOTE: Consult your System Administrator if you are unsure of
the settings required for your network.
Figure 6. LED Status Indicators
Table 1: Description of LED Status Indicators
Transceiver
PC Running Terminal Session
Software Configuration
There are two methods for communicating with the radio for configuration and management: Serial (COM1 DB9 connector) and
Telnet (ETHERNET RJ-45 connector). Both present identical
functionality, but the method of access is different for each. The
focus here is on Serial access, but Telnet may be used by following
these additional points, which replace Steps 1 and 2 below:
• For Telnet, connect to the radio with a PC that is on the
same IP network as the transceiver. Launch a Telnet program, and connect to the radio using its programmed IP
address.
• The default IP address is 192.168.1.1. If you do not know the
IP address of the radio, use the serial configuration steps
below to view the address with the IPCONFIG command.
1. With a PC connected to the COM1 serial port, launch a
terminal program, such as HyperTerminal (included with most
pre-Vista Windows®-based PCs) and set the following
parameters:
8 bits, no parity, one stop bit (8N1), flow control disabled,
VT100 emulation. The radio’s COM1 port automatically
determines the connected baud rate (within the range of
1200–115200 bps).
2. Press the ESCAPE key followed by a series of ENTER
keypresses (1/2 second intervals) until the > prompt appears.
The radio is now ready to accept commands.
3. Set/verify the RX (receive) and TX (transmit) frequencies. To
set the receive frequency, enter RX followed by the correct frequency in MHz (xxx.xxxxx). Press ENTER .
To set the transmit frequency, enter TX followed by the correct
frequency in MHz (xxx.xxxxx). Press ENTER .
4. The factory default modem settings support operation for most
systems. Other options are available using the proper software commands. The current setting may be viewed using the
Description
PWR
• Continuous—Power applied, no problems detected.
• Rapid flash (5x-per-second)—Alarm indication.
LAN
• Flashing—Ethernet data activity is detected.
• Off—Ethernet signals not detected, or excessive
traffic is present at the port.
DATA1/DATA2
These LEDs show data activity on the DB-9 serial
payload port(s).
LINK
When lit, indicates that a communication link exists
with the master station.
DB-9M to COM1 Port
Figure 5. Setup for PC Configuration
2.1.1
LED Name
NOTE: The Ethernet connector also has two embedded LEDs. A
flashing green indicates Ethernet data activity, and a
yellow indicates 100 Mbps operation has been achieved.
2.2.2
Antenna SWR Check
Before placing the unit in final operation, the antenna system’s
standing wave ratio (SWR) should be checked using a wattmeter
suited to the frequency of operation. High SWR (above 2:1) may
indicate an antenna or feedline problem, and should be corrected.
2.2.3
RSSI Check (for Remotes)
Using the RSSI command (received signal strength indication),
check for adequate signal strength. The radio must be receiving a
signal from the associated Master Station (LINK LED on or
blinking). In general, signal levels stronger than –80 dBm will provide very reliable communication and allow for a degree of “fade
margin.”
Optimize the RSSI at Remotes by slowly adjusting the direction of
the station antenna. Watch the RSSI indication for several seconds
after making each adjustment so that the RSSI accurately reflects
any change in the signal strength. With RSSI, the less negative the
number, the stronger the incoming signal (i.e., -70 dBm is stronger
than -80 dBm).
3.0
TROUBLESHOOTING
All radios in the network must meet the following basic requirements for proper operation. Check these items first when troubleshooting a communication problem:
• Adequate and stable primary power
• Secure cable connections (RF, data and power)
• A clear transmission path between Master and each Remote
MDS SD Series Quick Start Guide (x710 Mode)
05-4692A01, Rev. 03 (FCC)
• An efficient and properly aligned antenna system providing
adequate received signal strength.
• Proper programming of the transceiver’s parameters
• The correct interface between the transceiver and the connected data equipment (correct cable wiring, proper data
format, timing, etc.)
3.1
4.2.1
Pin Descriptions—RS-232 Mode
Table 2 provides pin descriptions for the connector when operating
in RS-232 mode. For RS-422/485, refer to the Reference Manual.
NOTE: The radio is hard-wired as a DCE device.
LEDs
The radio’s LED indicator panel provides useful information when
troubleshooting a system problem. Refer to Table 1 for LED information.
3.2
Event Codes
When an alarm condition exists, the transceiver creates a message that can be read on a connected PC by using the ALARM
command. Consult the Reference Manual for details.
3.2.1
Types of Alarms
Minor Alarms—report conditions that, under most circumstances
will not prevent transceiver operation. This includes out-of-tolerance conditions, baud rate mismatches, etc. The cause of these
alarms should be investigated and corrected to prevent system
failure.
Major Alarms—report serious conditions that generally indicate a
hardware failure, or other abnormal condition that will prevent (or
seriously hamper) further operation of the transceiver. Major
alarms may require factory repair. Contact your factory representative for assistance.
3.3
Built-In Spectrum Analyzer
A Spectrum Analyzer screen is available for viewing other radio
signals near the SD’s operating frequencies. Access to the analyzer is made with the Spectrum command.
Optionally, you can specify a frequency at the prompt to view the
surrounding spectrum of that frequency To do this, enter Spectrum xxx.xx, where xxx.xx is the frequency in MHz.
The display creates a received signal strength indication (RSSI)
vs. frequency plot for the frequency and surrounding signals. Refer
to the Reference Manual for more information.
4.0
COM1 Connections for PC Control
The COM1 DB-9 connector is used for PC management of the
radio. A straight-through cable is required that connects Pin 2
(RXD), Pin 3 (TXD), and Pin 5 (Ground). (See Figure 7.)
2 RXD
DB-9 MALE
(RADIO SIDE)
3 TXD
> RXD
TXD 3
Pin
No.
Input/
Output
OUT
DCD (Data Carrier Detect/Link)—A low
indicates signal received.
OUT
RXD (Received Data)—Supplies received data to
the connected device.
IN
TXD (Transmitted Data)—Accepts TX data from
the connected device.
IN
Sleep Mode Input—Grounding this pin places the
radio in a low power consumption mode.
--
Signal Ground—Connects to ground (negative
supply potential) on chassis.
OUT
Alarm Output (DSR)—Behavior is
user-configurable. Default behavior: An RS-232
high/space (+5.0 Vdc) on this pin indicates an
alarm condition. An RS-232 low/mark (–5.0 Vdc)
indicates normal operation.
IN
RTS (Request-to-Send)—Keys the transmitter.
OUT
CTS (Clear-to-Send)—Goes “high” after the
programmed CTS delay time has elapsed (DCE),
or keys another connected radio when RF data
arrives (CTS KEY).
--
5.0
Pin Description
Reserved—User I/O for special applications.
COMMAND OVERVIEW
Table 3 on the following page lists key software commands for the
SD transceiver. Many commands can be used in two ways:
COM1/COM2 REFERENCE
4.1
Table 2: COM2 Pin Descriptions—RS-232
1. The basic command (shown first) may be entered alone to
issue a query or execute a simple command.
2. The basic command may be appended with additional arguments (shown in brackets, if applicable) to further define a setting.
A complete list of commands and detailed descriptions is provided
in the SD Reference Manual (under development for SD2).
DB-9 FEMALE
(COMPUTER)
GND 5
5 GND
RF Exposure Notice
Figure 7. COM1 Wiring to Computer
4.2
COM2 Connections
The COM2 connector (Figure 8) is typically used to connect an
external DTE telemetry device to the radio, supporting the RS-232
or RS-485 (balanced) format, depending on how the radio is configured. The radio supports data rates of 300, 1200, 2400, 4800,
9600, 19200, 38400, 57600, and 115200 bps (asynchronous data
only).
The COM2 connector mates with a standard DB-9 plug available
from many electronics parts distributors.
Figure 8. COM2 Connector (DB-9F)
As viewed from outside the radio
05-4692A01, Rev. 03 (FCC)
The radio equipment described in this guide emits radio frequency energy.
Although the power level is low, the concentrated energy from a directional
antenna may pose a health hazard. Do not allow people to come closer
than 1.50 meters to the front of the antenna when the transmitter is operating with a 7 dBd (9.15 dBi) gain antenna. Use of higher gain antennas
means increasing the distance accordingly. This guide is intended for use
by a professional installer.
FCC Part 15 Notice
Operation of this device subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Any unauthorized modification or changes to this
device without the express approval of the manufacturer may void the
user’s authority to operate this device. Furthermore, this device is intended
to be used only when installed in accordance with the instructions outlined
in this guide. Failure to comply with these instructions may void the user’s
authority to operate this device.
MDS SD2 Quick Start Guide (x710 Mode)
Table 3: Key Software Commands
Command
Function
ALARM
Read current operating condition of the radio.
BAUD [xxxxx abc]
Set/display the data rate and control bits.
BUFF [ON, OFF]
Enables or disables the internal radio data
buffer.
CTS [0-255]
Set/display the Clear-to-Send delay in
seconds.
DEV
Display modem control deviation.
DEVICE [DCE, CTS KEY]
Set/display device mode.
DKEY
Dekey the radio (transmitter OFF). This is
generally a radio test command.
DUMP
Display all programmable settings.
HELP
Shows available commands.
KEY
Key the radio (transmitter ON). This is
generally used as a radio test command.
MODEM [xxxx]
Set the modem characteristics of the radio.
PORT [RS232, RS485]
Set/display COM2 data port interface
settings.
PTT [0-255]
Set/display the Push-to-Talk delay in
milliseconds.
PWR [20-37]
Set/display the transmit power setting.
RSSI
Display the Received Signal Strength
Indication.
RTU [ON/OFF/0-80]
Re-enables or disables the radio’s internal
RTU simulator and sets the RTU address.
RX [xxx.xxxx]
Set/display the receive frequency.
RXLEVEL [-20 to 0]
Set/display the receive audio input level.
SCD [0-255]
Set/display the Soft-Carrier Dekey delay in
milliseconds.
SHOW [DC, PWR]
Display the DC voltages and transmit power
level.
SNR
Signal-to-Noise Ratio, expressed in dB
SPECTRUM [xxx.xx]
Display the transceiver’s built-in spectrum
analyzer, where xxx.xx denotes center
frequency.
STAT
Display radio status and alarms.
TEMP
Display the internal temperature of the radio
in degrees C.
TOT [1-255, ON, OFF]
Set/display the Time-out Timer delay in
seconds.
TX [xxx.xxxx]
Set/display the transmit frequency.
TXLEVEL [-20 to 0, AUTO]
Set/display the transmit audio input level.
UNIT [10000...65000]
Set/display the transceiver’s unit address.
MDS SD2 Transceiver (x710 Mode)
05-4692A01, Rev. 03 (FCC)
November 2009
GE MDS, LLC
175 Science Parkway
Rochester, NY 14620
General Business: +1 585 242-9600
FAX: +1 585 242-9620
Web: www.gemds.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c320 44.293068, Sun Jul 08 2007 18:10:11
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2009:11:12 11:52:22-05:00
Create Date                     : 2007:03:01 15:15:37Z
Metadata Date                   : 2009:11:12 11:52:22-05:00
Format                          : application/pdf
Title                           : 4692A-SD2_Quick_Start_(FCC).fm
Creator                         : kcarey
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:62641490-5403-4e53-b0e7-c3a8a7f2a091
Instance ID                     : uuid:486d034d-e4a2-47f4-80be-6dc3df4e113e
Page Count                      : 4
Author                          : kcarey

EXIF Metadata provided by EXIF.tools