GE Built In Oven, Electric With Microwave Manual L0608178
JKP85BD1BB JKP85BD1BB GE MICROWAVE - DOUBLE OVEN - Manuals and Guides L0608178 View the owners manual for your GE MICROWAVE - DOUBLE OVEN #JKP85BD1BB. Home:Kitchen Appliance Parts:GE Parts:GE MICROWAVE - DOUBLE OVEN Manual
User Manual: GE GE Built In Oven, Electric with Microwave Manual GE Built In Oven, Electric with Microwave Owner's Manual, GE Built In Oven, Electric with Microwave installation guides
Open the PDF directly: View PDF 
.
Page Count: 12
Installation
Instructions
27" Built In Wall Oven/with
Microwave
JKP85
"If you have questions, call 800-GE-CARES orvisit our website at:
www. GEAppliances.com"
Before you begin
Read these instructions carefully and completely
• IMPORTANT-Save these instructions for
local inspector's use.
•IMPORTANT-Observe all governing
codes and ordinances.
•Note to Installer- Be sure to leave these
instructions with the consumer.
•OWNER- Keep these instructions for future
reference.
•ATTENTION INSTALLER!!
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A "plug and receptacle" is NOT
permitted on these products
•NOTE- This appliance must be properly
grounded.
Parts Included
8 flat head screws side trim
3 Pan head screws bottom trim
fBottom Trim
Materials Needed
Strain Relief
Clamp
_¢_ WireNu_ts
Junction
Box
36" of String
Tools You Will Need
1/8" Drill Bit & Phillips
Electric or Screwdriver
Hand Drill
Pub. No. 31-10480
229c4053P460 1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
•Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall cover-
ings around the oven can withstand the
temperatures (up to 200°F.) generated by
the oven.
_CAUTION: The electrical power
to the oven supply line must be
shut off while line connections
are being made. Failure to do so
could result in serious injury or
death.
Electrical
Requirements
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
(Rating Plate is located on oven side trim.)
We recommend you have the electrical wiring
and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main oven
disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to wire
your oven according to governing codes could
result in a hazardous condition. If there are no
local codes, your range must be wired and
fused to meet the requirements of the National
Electrical Code, ANSI/NFPA No. 70-Latest
Edition. You can get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a 4 conductor
connection to an electric range. When
installing an electric range in new construction,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
2
Installation Instructions
Pre-Installation Checklist
Remove packaging materials.
Check behind hinges, and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, and all tape around oven.
Door Removal is not a requirement for
installation of the product, but is an added
convenience.
Open the oven door as far as it will go.
Open oven door and remove literature
pack, broiler pan and grid, and oven
racks.
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and
Care, Installations, etc. in a safe place
for future reference.
Push both hinge
locks down toward
the door frame, to
the unlocked
position. This may
require a flat blade
screwdriver.
Hinge
_. Unlocked
Hinge
Arm
Place hands on
both sides of the
door, close the oven
door to the removal
position this is half
way between the
broil stop and fully
closed.
Hinge
/ Clears
Slot
3 (Continued on following page)
Installation Instructions
1_ Place the oven on a table or platform Iq_"
even with the cutout opening.
(Platform must support 275 Ibs.)
Remove the bottom trim from the
top of the oven. It will be installed at
the end of installation. The trim is
wrapped separately and taped to the
top of the unit.
Bottom Trim
4
Installation Instructions
Cutout for Built-In Oven W/Microwave
Allow 7/8"
for overlap of
oven over side ....
edges of cutout_
Allow a minimum of 20"
for clearance to adjacent
corners, drawers, walls, etc.
when doors are open
CABINET
27"
CUTOUT
WIDTH
25" MIN.
25 1/4" MAX.
2" x 4"
or _
equivalentt
runners
JUNCTION BOX
LOCATION
CUTOUT _[
HEIGHT 48"
41 1/8" MIN.
MAX. TO bottom
of junction box
Alternate
junction box
location
Cabinet Width 27"
Recommended
Cutout Location
From Floor ..... 21 5/8"
Cutout Depth .23 1/2"
Cutout Width ..25" Min.
........................ 25 1/4" Max.
Cutout Height 41 1/8" Min.
........................ 41 1/4" Max.
Overall Height 41 5/8"
Overall Width .. 26 5/8"
Allow 1" for
overlap of oven
top and bottom
of cutout
Recommended
cutoutlocation
floor
21 5/8"
If the cabinets do not have a solid bottom, then
two braces or runners must be installed to
support the weight of the oven. The runners
and braces must support 275 pounds.
NOTE: If the cabinet does not have
afront frame and the sides are less
than 3/4" thick, shim both sides
equally to establish the cutout
width.
i
2" x4" or
Equivalent
Runners
27" _
NOTE: If using equivalent
runners, then the center of
the equivalent runners
should be 20 112".
Installation Instructions
ElectricalConnections
ATTENTION INSTALLER!!!
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT
permitted on these products.
Do not shorten the flexible conduit.The
conduit strain Relief Clamp must be securely
attached to the junction box and the flexible
conduit must be securely attached to the
clamp. If the flexible conduit will not fit within
the clamp, do not install the oven until a
clamp of the proper size is obtained.
NOTE TO ELECTRICIAN: The 3 power leads
supplied with this appliance are UL recognized for
connection to larger gauge household wiring. The
insulation of these 3 leads is rated at temperatures
much higher than the temperature rating of house-
hold wiring. The current carrying capacity of the
conductor is governed by the temperature rating of
the insulation around the wire, rather than the wire
gauge alone.
,_ WARNING: Improper connection ofaluminum house wiring to copper
leads can result in an electrical
hazard or fire. Use only connectors
designed for joining copper to aluminum
and follow the manufacturer's
recommended procedure closely.
Turn off the circuit breaker or remove fuses
to the oven branch circuit.
With the oven in front of the cabinet
opening, on a table or platform, connect the
flexible conduit to the electrical junction box
as shown below. You will need to purchase
a strain relief clamp to complete the
connection of the conduit to the junction
box.
A SUPPORT
TOASSIST EN
°°g2._ggT"_
6( Continued on Next Page)
Installation Instructions
Electrial Connections cont.
NEW CONSTRUCTION AND
FOUR-CONDUCTOR BRANCH
CIRCUIT CONNECTION
•When installing in a new construction,
or
• When installing oven in a mobile
home, or
• When local codes do not permit
grounding through neutral:
a. Cut the neutral (White) lead from the crimp.
Re-strip the neutral (white) lead to expose the
proper length of conductor.
OR
Three-Conductor Branch
Circuit Connection
When connecting to a 3-conductor branch
circuit, if local codes permit:
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to the
branch circuit neutral (white or gray in
color), using wire nut.
Junction
Box Cover
Ground
Wires
b.Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING note.
c. Connect the oven neutral (white) lead to the
branch circuit neutral (white or gray) in
accordance with local codes, using wire nut.
d.Connect the oven red lead to the branch circuit
red lead and the oven black lead to the branch
circuit black lead in accordance with local
codes, using wire nuts. If the residence red,
black or white leads are aluminum conductors,
see" WARNING" note on preceeding page.
e. Install Junction Box Cover.
Ground
/Wires
Ground and
neutral wires
_Junction
Box Cover
b.Connect the oven red lead to the branch
circuit red lead, using wire nut.
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using wire nut. If the residence red,
black or white leads are aluminum
conductors, see "WARNING" note on
preceeding page.
d. Install Junction Box Cover.
7
Installation Instructions
Placing the Oven in the Opening
IC-_ Sliding the Oven Into the
Opening.
a. Loop (do not tie) a 36" string around the
conduit before the oven is slid into place.
This will keep the conduit from falling behind
the oven.
Pull out on string
loop while
pushing the oven
into the cabinet
b. Lift oven into cabinet cutout using the oven
opening as an grip. Carefully push against
oven front frame. Do not push against
outside edges.
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the oven
in a natural loop.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.
Drilling the Pilot Holes
Note: Before drilling the pilot holes
make sure the oven is pushed as far
back into the opening as it will go
and centered.
a. Drill four-I/8" pilot holes through the mounting
holes (top and bottom) of the side trim, for
the eight #8 screws provided.
The screws must be
a minimum of 1/4"
from the front of the
cutout.
NOTE: Mounting screws must be
used. Failure to do so could result in
the oven falling out of the cabinet
causing serious injury.
b. Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use 4 #8 x 3/4 particle board screws.
These may be purchased at any hardware
store.
8
Installation Instructions
Preparing for the bottom
Trim Installation
a. With oven installed, take the bottom trim
and center it on the bottom front edge of
the cabinet opening.
b. Using the trim as
a template mark
the center of
each slot (three
total) where
the mounting
holes will be
drilled.
c. Remove the trim.
Mounting Holes
d. Drill pilot holes into the center of each
template mark.
Installing the Bottom
Trim
a. Place the bottom trim centered over the
pre-drilled mounting holes. Tape the edges
of the trim down to maintain the alignment.
Side
Trim
Screw
Side
Lower
Trim
b. Using the three pan head trim screws
provided secure the bottom trim to the
bottom edge of the cabinet.
IMPORTANT: If this unit is ever removed
from the cabinet or the cavity is ever
pulled out for service, the trim must be
removed first or damage to the trim will
occur.
Replacing the Oven
Door
The oven door is heavy. You may need
help lifting the door high enough to
slide it into the hinges slots. Do not lift
the door by the handle.
Replacing the Oven Door _Pick the Oven Door up by
placing one hand on each
side. The door is heavy so
you may need help. Do not
lift the door by the handle.
i i i
Place the notch of the
hinge arm into the
bottom edge of the
hinge slot.
I_ Open the oven door as
far as it will open.
Bottom Edge Hinge Arm
Of Slot, _
Hinge Notch
Push the hinge locks
up against the front
frame of the oven
cavity, to the locked
position.
Close the oven door.
Hinge in
Locked Position
Notch of
Hinge Securely
Fitted into Bottom
of Hinge Slot
9
Installation Instructions
PRE-TEST CHECK LIST
Check that the bottom trim is installed
Remove all protective film if present,
and any stickers. _ properly (see page 9).
Chec to surethatallwi in0is
secure and not pinched or in contact
with moving parts.
Check to be sure the mounting screws
are installed and flush with the side
trim, (see page 9).
_Operation Checklist
[_ emove all items from the inside 11k61rl
of the oven.
I_ Checkthat conduit is securely
connected to the junction box.
Turn on the power to the oven.
(Refer to your Use and Care
Manual.) Verify that the bake and
broil units, and all cooking
functions operate properly.
Check that the circuit breaker is
not tripped or the house fuse is
blown.
See Use & Care manual for
troubleshooting list.
NOTE TO ELECTRICIAN:
The power leads supplied with this
appliance are UL recognized for
connections to larger gauge
household wiring. The insulation of
these leads is rated at temperatures
much higher than the temperature
rating of household wiring. The
current carrying capacity of a
conductor is governed by the wire
gauge and also the temperature rating
of the insulation around the wire.
NOTE: ALUMINUM WIRING
A. WARNING:
IMPROPER CONNECTION OF
ALUMINUM HOUSE WIRING TO
THE COPPER LEADS CAN
RESULT IN A SERIOUS PROBLEM.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum and
follow the manufacturer's
recommended connector
procedure closely.
NOTE:Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice
and local codes.
10
NOTES
11
Pub. No. 31-10480
229c4053P460
