GE Wine Cooler Manual L0809307
User Manual: GE GE Wine Cooler Manual GE Wine Cooler Owner's Manual, GE Wine Cooler installation guides
Open the PDF directly: View PDF 
.
Page Count: 12
Design Gui e with
Installation
I0
struct n
Fresh-Food
ZIFI240
ZIFS240
Refrigerator
Bar Refrigerator with Icemaker
ZIBi240
ZIBS240
monogram.com
Safetg Information
BEFORE YOU BEGIN:
Read these instructions completely and carefully.
IM PORTANT - Soretheseinstructions
for Iocol inspector's use.
IMPORTANT - Observeollgoverning codes
ond ordinonces.
Note to Installer - Be sure to leove these
instructions with the Consumer.
Note to Consumer - Keepthese instructions with
your Owner's Honuol for future reference.
WARNING - Thisopplioncemust be
properly grounded. See below.
AVERTISSEMENT-
Cet opporeil doit @trecorrectement mis 5 Io terre.
Consulter ci-dessous.
If you received o domoged Fresh-Food Refrigerotor
or Bor Refrigerotor with Icemoker, you should
immediotely contoct your deoler or builder.
Skill Level -Instollotion requires bosic mechonicol
skills. Proper instollotion is the responsibility of the
instoller. Product foilure due to improper instollotion
is not covered under the GEApplionce Worronty.
WARNING:
• Usethis opplionce only for its intended purpose.
• Immediotely repoir or reploce electricol service cords
thot become froyed or domoged.
Unplug the unit before cleoning or moking repoirs.
Repoirs should be mode by o quolified service
technicion.
AVERTISSEMENT :
• IIne fout utiliser cet opporeil que pour I'usoge pour
lequel il o @t@construit.
IIfout r_porer ou remplocer imm@diotement tout
cordon d'olimentotion @lectriqueeffiloch@ou
endommog&
D@bronchezle r@frig_roteur ovont le nettoyoge
ou toute intervention.
Les r@porotionsdoivent @trefoites por un technicien
quolifi&
For Monogram local service in your area, call
1.800.444.1845
For Monogram service in Canada, call
1.800.561.3344
For Monogram Parts and Accessories, call
1.800.626.2002.
monogram.com
GROUNDING THE FRESH-FOOD REFRIGERATOR OR BAR REFRIGERATOR
WITH ICEMAKER
IMPORTANT - Pleosereodcorefully.
FOR PERSONAL SAFETY,THISAPPLIANCE MUST BE PROPERLY GROUNDED.
The power cord of this opplionce is equipped with o 3-prong (grounding) plug which motes with o stondord 3-prong
(grounding) woll receptocle to minimize the possibility of electric shock hozord from this opplionce.
Hove the woll outlet ond circuit checked by o quolified electricion to moke sure the outlet is properly grounded.
Where o stondord 2-prong woll outlet is encountered, it is your personol responsibility ond obligotion to hove it reploced
with o properly grounded 5-prong woll outlet.
DO NOT, UNDERANY CIRCUMSTANCES,CUT OR REMOVETHE THIRD
(GROUND)PRONG FROMTHE POWERCORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR
TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.
Installation Instructions
CONTENTS
Design Guide (For ZIFS240 and ZIBS240}
TheInstallationSpace............................................................................................4
ProductClearances..................................................................................................4
Side-by-SideInstallations....................................................................................4
Design Guide (For ZIFI240andZLBI240}
TheInstallationSpace............................................................................................5
ProductClearances..................................................................................................5
Side-by-SideInstallations....................................................................................5
Important Information
PartsRequired..............................................................................................................3
Caringfor YourStainlessSteel..........................................................................3
Tools,Hardware........................................................................................................3
StainingWoodDrawerFronts..........................................................................3
InstallWaterLine......................................................................................................3
Installation Instructions
Step Z,Remove Packaging and Installation Parts ................................6
Step 2, Install Custom 3/4" Door Paneland Handle
(ZIFI240and ZIBI240 models only) ............................................................6, 7
Step 3, Leveling............................................................................................................7
Step4, ConnectWater Supply (ZIBI240and ZIBS240models only)..7
Step 5, Connect Power ..........................................................................................8
Step 6, Slide Product into Cutout ......................................................................8
Step 7, Set Temperature Controls....................................................................8
ZTBSSZTubular Handle Kit..................................................................................9
ZIFI240 AND ZIBI240 MODELSONLY
PARTS REQUIRED PARTS SUPPLIED
•Custom handle • Handle side trim
• Assembled overlay panel • Optional black or
• Screws stainless steel toekick
CARING FOR YOUR STAINLESSSTEEL
• Before installation or first use,we strongly advisethat
you polish the stainless steel exterior and handle with
a commercially available stainlesssteel cleaner such as
StainlessSteel Magic.T"To preserve and protect the fine
finish, we also strongly advise that you apply stainless
steel cleaner monthly.
TOOLS/HARDWARE REQUIRED
• Adjustable wrench
• Carpenter's glue (ZIFI240and ZIBI240 models only)
• Screwdriver (ZIFI240and ZIBI240 models only)
STAINING WOOD DRAWER FRONTS
The drawer fronts are unfinished cherry wood. During use,
oil from hands may accumulate and stain the wood.
• The drawer fronts may be stained and sealed to match
adjacent cabinetry.
• Apply the stain and sealer according to the manufacturer's
instructions. Toavoid unpleasant odor, keep the door open
to ventilate and allow the stain/sealer to dry completely
before using the product.
INSTALL WATER LINE (ZIBI240 AND ZIBS240 MODELS ONLY)
• A cold water supply is required for automatic icemaker
operation. The water pressuremust be between 20 and
120 p.s.i.
• The water line can enter the opening through
the floor or back wall. Route1/4" O.D.copper tubing or GE
SmartConnectT"kit between the cold water line and water
connection location, long enough to extend to the front of
the refrigerator.
• Install an optional water filter in the water line near the
refrigerator. A water filter is recommended in areas where
the water supply contains sand and particles. Installation
Instructions are packed with the filter.
NOTE:The only GEapproved plastic tubing is supplied in
the GESmartConnectT"Refrigerator Tubing kits.Do not use
any other plastic water supply line becausethe line is under
pressureat all times. Other types of plastic may crack or
rupture with age and cause water damage to your home.
GESmartConnecf" Refrigerator Tubing Kitsare available
in the following lengths:
2' (0.6m) WXO8XIO002 15' (4.6m) WXO8X10015
6' (1.8m) WXO8XIO006 25' (7.6m) WXO8X10025
Water Line Water Line
ShadedArea
10-1/2"
Floor 1-1/2"
min.
Shut off the main water supplg.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve (required)between the icemaker
water valve and coldwater pipe in a basement or cabinet.
The shut-off valve should be located where it will be easily
accessible.
• Turnon the main water supply and flush debris. Runabout
a quart of water through the tubing into a bucket. Shut off
water supply at the shut-off valve.
NOTE:Saddletype shut-offvalves are included in many water
supply kits,but are not recommended for this application.
NOTE:Commonwealth of Massachusetts Plumbing Codes
248CMRshall be adhered to. Saddlevalves are illegaland use
is not permitted in Massachusetts.Consult with your licensed
plumber.
Design Guide
For models ZIFS240 and ZIBS240 with Stainless Steel Doors and Handles
THE INSTALLATION SPACE
_E:
er line location
IBI240 or
,_23_3/4,!_(_'_ , ZIBS240 model only
_'X[ N 23:3/4"
NOTE:
Hondle ond
hondle stondoff
depth is 2-1/4".
26"
Including
Hand_
_ 31-1/4"
to 34-3/4"
.....23-3/4"--4
The cutout depth should be 24"
The cutout dimensions shown ollow for o full door
swing ond occess to the pull-out rocks when instolled
in stondord 24" deep cobinets.
• All models mog be used freestonding.
If instolling o stoinless steel model between fromeless
cobinets, o !/2" wide filler strip or side ponel mog be
needed on the hinge side.The filler strip will oct os
o spocer between the cose ond odjocent cobinet door
swing. The width of the opening must include the filler
ponels.
Note: The stoinless steel door should be flush with the
surrounding cobinets.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 omp power supplg is
required. An individuol properlg grounded bronch circuit
or circuit breoker is recommended. Instoll o properlg
grounded 3-prong electricol receptocle recessed into
the bock woll os shown. Electricol must be Iocoted on
reor woll os shown. NOTE:GFCI(ground foult circuit
interrupter) is not recommended.
PRODUCT CLEARANCES
The Fresh-Food Refrigerator or Bar Refrigerator with
Icemoker is foctorg set for o 110° door swing.
When installed in a corner:
• Allow 14" minimum clearance on the hinge side
for a full 110° door swing.
Allow 4" min. clearance on the hinge side for
the 90° door swing and to allow racks to slide out.
NOTE:Clearances are based on the recommended
2-1/4" handle standoff depth.
m
h
\,
110°
14"Minimumto Wall
110° Door
Swing
\\
I 90° Door T
Swing 21-5/8"
iL t
'i
ii 23-5/8"
go°. _ ...
4"MinimumtoWall
NOTE:Right hond models illustroted. Allow the some
cleoronces on the opposite side for left hond fresh food
models ZIFI240ond ZIFS240only. ModelsZIBI240ond
ZIBS240ore not ovoiloble with left hond door swing.
Test the door swing. Corefull9 open ond close the door.
The door should not rub or cotch on odjocent cobinetr9.
Choose the location:
These products mog be closed in on the top ond
three sides os long os the front is unobstructed for
oir circulotion ond proper occess to the door.
Do not instoll these products where the temperoture
will go below 55°F (!3°C) or above 90°F (32°C).
These products ore not designed to be stocked one
over the other.
SIDE-BY-SIDE INSTALLATIONS
For ocomplete refreshment center, instoll oFresh-Food Refrigerotor
beside o Double Drower Refrigerotor, Beveroge Center or Wine Chiller/
Wine Reserve. Or, instoll o Refrigerotor with Icemoker beside
o Wine Chiller/Wine Reserve.
• A side-bg-side instollotion requires ot leost o47-1/2" wide opening.
No trim kits required.
Products must operate from separate, properlg grounded receptacles.
101j210
E___ %47-1/2"Min.
4
Design Guide
For models ZIFI240 and ZIBI240 with Custom Door Panels and Handles
THE INSTALLATION SPACE
24"
34-1/2"-35"
_23-3/4" Min._-X_
NOTE: If installing between
frameless cabinets, a 1/2"
wide filler strip or side panel
mag be needed on the hinge
side. The filler strip will act as
a spacer between the door
case and adjacent cabinet
and will prevent interference
with the cabinet door swing.
The width of the opening
must include the filler panels.
24-7/8"
NOTE:
Water line location
for ZIBI240 or
ZIBS240 model onlg
to 134-3/4"
.....23-3/4"-4
The cutout depth should be 24"
The cutout dimensions shown allow for a full door
swing and access to the pull-out racks when installed
in standard 24" deep cabinets.
• All models may be used freestanding.
• In a standard 24" opening, the refrigerator door will
protrude 1-5/4" forward of the adjacent cabinets.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supplg is
required. An individual properlg grounded branch circuit
or circuit breaker is recommended. Install a properlg
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located on
rear wall as shown. NOTE:GFCI(ground fault circuit
interrupter) is not recommended.
Black or Stainless Steel Toekick Options
• Theseproducts are shipped with a stainlesssteeltoekick
and a black toekick. For shipping purposes, one of the
toekicks will be secured to the back of the unit, and the
second will be installed on the unit. Keepthe unused
toekick and any unused parts for future use.
PRODUCT CLEARANCES
The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factorL set for a 110° door swing.
When installed in a corner:
• Allow 16" minimum clearance on the hinge side
for a full 110° door swing.
• Allow 4-1/2" min. clearance on the hinge side for
the 90° door swing and to allow racks to slide out.
NOTE:Custom handle clearances may vary.
16"Minimumto Wall
110°D°°r [
Swing
i
L. '\,,,
\{i)\
110° - . ..... ..',,_',,
, 90° Door
Swing
h
[
t
21-5/8"
23-5/8"
90°
4-1/2"Minimumto Wall
NOTE:Righthand models illustrated. Allow the same
clearances on the opposite side for left hand fresh food
models ZIFI240and ZIFS240only. ModelsZIBI240and
ZIBS240are not available with left hand door swing.
• Test the door swing. Carefully open and close
the door. The door should not rub or catch on adjacent
cabinetry. NOTE:When installing custom panel and
handle, use above clearances as a general guide but
adjust according to the installation.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.
• Do not install these products where the temperature will
go below 55°F (13°C)or above 90°F (32°C).
• These products are not designed to be stacked one
over the other.
ZTBSSl--Monogram stainless steel tubular handle
for 3/4" thick custom panels. Order this kit from your
Monogram supplier.
SIDE-BY-SIDE INSTALLATIONS
For a complete refreshment center, install a Fresh-Food Refrigerator
beside a Double Drawer Refrigerator, Beverage Center or Wine Chiller/
Wine Reserve. Or, install a Refrigerator with leemaker beside
a Wine Chiller/Wine Reserve.
• A side-bg-side installation requires at least a 47-1/2" wide opening.
No trim kits required.
• Products must operate from separate, properly grounded receptacles.
Installation Instructions
ISTEP11REMOVE PACKAGING
AND INSTALLATION PARTS
• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape and protective
plastic coverings.
• Removethe toekick attached to the back of the unit.
• Removethe custom panel attached to the front of
the unit.
CAUTION: Small objects area choke hazard
for children. Remove and discard any parts not used.
ATTENTION :,espetits objets peuvent
_trangler les enfants. II fautjeter toutes les pi_ces qui
ne sont pas utilis_es.
ISTEPzlINSTALL CUSTOM 3/4"
DOOR PANEL AND HANDLE
(ZIFI240and ZIBI240modelsonly)
314" Overley Penel Dimensions
Hodel ZIFI240 and ZIBI240 require
a field-installed overlay door panel.
• The overlay panel must be
secured to a 1/4" thick backer
panel that slides into the trim.
A.10" thick spacer panel must
be placed between the overlay
and backer panel.
• A custom handle of your choice,
supplied by your cabinetmaker,
Overlay
Panel
Door I
1/4" ,
Backer_ \10 Inch
Panel Spacer
must be installed on this overlay panel. Countersink all
screws into the backer panel. Screws cannot protrude
from the backer panel.
IMPORTANTNOTE:Haximum total weight for custom
door panel is 25 pounds.
I 1/4" Backer 23-3/16" 29-9/16"
0.10" Spacer 22-1/2" 29-1/16"
3/4" Overlay 23-5/8" 30"
-_-'-- A ---'_"-
ISTEPzlINSTALLCUSTOM 3/4" DOOR
PANEL AND HANDLE (CONT.)
(ZIFI240and ZIBI240modelsonly)
Assemble overlay panels
with glue and screws.
• Centerspacerpanelon the
backerpanel,leftto right and
top to bottom. Securethe
panelswith glue.
• Center the spacer/backer
panel on the overlay panel.
Secure with glue and screws. Countersink all screws
into the backer panel.
Custom Penel Hinge Routing Dimensions
Use a 3/4"router bit to cut a notch into the back side of
the assembled panel 3/8" toward the front of the overlay
panel, 3/4" deep and 7/8" wide.
NOTE:Righthandmodels
illustrated.Cutnotchesonthe
oppositesidefor lefthandfresh
fooddoorswingmodels .\,
ZIFI240andZIFS240. ?,
Backside
of custom
panel /
Mj
3 _ _
314"
Instell custom door penel end hendle:
• Open door to 90°.
• Remove 5 screws holding trim; lift off trim.
Retain screws.
FNOTE:Right hand models
illustrated. Follow the
same instructions on the
opposite side for left hand
fresh food door swing
models ZIFI240 and
ZIFS240.
Installation Instructions
ISTEP21INSTALLCUSTOM 3/4" DOOR
PANEL AND HANDLE (CONT.)
{ZIFI240 and ZIBI240 models only)
Instell custom door panel end hendle (cont.):
• A custom handle of your choice, supplied by your
cabinetmaker, must be installed onto the overlay panel
before the panels are slid into the trim. Countersink all
screws into the backer panel. Screws cannot protrude
from the backer panel.
Screws Must
BeCountersunk
IntoPanel
Ha die
Custom ,_LJ
DoorPanels
• Slide overlay panel into the door trim.
• Reinstall the side trim using the trim screws removed
earlier.
:iii
• Placethe brushed decorative cover over the side trim
to hide the screw heads. Ensure side trim is aligned top
to bottom and front to back. Snap into place.
NOTE:
For shipping
purposes, the
brushed decorative
cover will be
secured to
the front of
the unit.
[STEP 3j LEVEL
• Use an adjustable wrench
to turn the leveling legs and
raise or lower the product.
For built-in installation, adjust
the leveling legs slightly below
the bottom of the countertop.
INSTALLATIONTIP:
Heasure floor to underside
of countertop inside the
opening. If the room floor
is higher than the opening
floor, adjust the rear
leveling legs approximately
Turn Right to Lower
Turn Left to Raise
1/8" less than the opening height. Screw front legs all
the way in to shorten the height at the front. This will
allow you to slightly tip the unit into the opening. Once
in the correct position, the front legs can be adjusted to
level the product.
ISTEP41CONNECTWATER SUPPLY
(ZIBI240 end ZIBS240 models only)
1/4" " 1/4"
__'--./<_ ,I L%..-Compression
_;_ _'_ Nut
SmartConnect" " \1 _---'_<k./
Tubing ""-----_'_ _ Refrigerator
Connection
Locate and bring the water line tubing to the rear
of the cabinet.
Turn the water on to flush debris from the line.
Run about a quart of water through the tubing
into a bucket, then shut off the water.
Copper Tubing:
• Slip a 1/4" nut and ferrule over both ends of the copper
tubing. Insert the tube into the refrigerator connection
on the unit and tighten the nut.
• Turn on the water to check for leaks.
GESmartConnect" Tubing:
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression nut
until it isjust hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check for leaks.
NOTE:Coil excess tubing length behind the unit.
Installation Instructions
[STEP 5j CONNECT POWER
• Connect power cord plug to a properly grounded
receptacle.
• Check to make sure power is on by opening the door
to see if interior light turns on.
Bar Refrigerator with Icemaker - The interior fan runs
all the time except during defrost cycle when the door
is open.
Fresh-Food Refrigerator - The interior fan runs
all the time except when the door is open.
Seethe Owner's Manual for further explanation of the fan.
iSTEP 7j SET TEMPERATURE
CONTROLS
• The temperature controls are preset. Referto
the Owner's Manual for more information. Allow
12-24 hours for the temperature to stabilize.
NOTE:The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker operate very quietly. You may not notice the unit
running, and when first installed, the fans and motor may
not come on immediately - this is normal. If the display is
lit and the light is working, the unit is operating.
iSTEP 6j SLIDE PRODUCT INTO
THE CUTOUT
CAUTION: Do not push against the door
panel with your knees. Do not push or lift the unit by
the door handle. Damage may occur!
ATTENTION :Nepoussez;amo s
le panneau de la porte ovec vos genoux. Ne poussez
jamois votre appareil ou ne le soulevezjamois par
la poign#e de porte. Vous pouvez I'endommager.
• Open the door and gently push the unit back into
the opening with your hands against the sides.
Be careful not to entangle power cord.
• In a standard 24" opening, the front face of
the stainless steel door will be flush with adjacent
cabinetry. A custom panel door may protrude
1-3/4" beyond the surrounding cabinets.
• Check again to be sure the unit is level.
• If the unit is installed under mcountertop, adjust
the leveling legs until the unit is resting firmly against
the underside of the countertop.
• If alignment with adjacent cabinetry is an issue,
use mshim to secure the unit against the underside
of the countertop.
ZTBSSI Monogram Tubular Handle Kit
• BEFORE YOU BEGIN:
Read these instructions completely and carefully.
• IMPORTANT:
Save these instructions for local inspector's use.
• IMPORTANT:
Observe all governing codes and ordinances.
• Note to Installer - Be sure to leave these instructions
with the Consumer.
Note to Consumer - Keep these instructions with gour
Owner's Manual for future reference. This kit provides a
stainless steel tubular handle to coordinate with other
Monogram appliances.
• The tubular handle must be installed onto the 3/4"
thick portion of the custom wood panel before
the panel is secured to the door.
TOOLS AND MATERIALS REQUIRED:
• Gloves to protect against sharp edges
#2 Phillips screwdriver
Drill and !/4" bit and 1/2" spade bit
Safetg glasses
Center punch
Pencil
THIS KIT INCLUDES
• Tubular handle
2 Mounting screws
2 Handle standoffs
2 Set screws for standoffs
2 Nuts
2 Washers
Allen Wrench
INSTALL THE TUBULAR HANDLE
Use the handle as a template to locate and mark the
exact position of the screw holes. Becareful to avoid
interference with custom panel mounting screws.
Draw a pencil line, top to bottom and 7/8" from the
outside edge.
• Hold the tubular handle against the appearance side,
centered on the marked line.
• Mark the screw hole locations at the center of the
handle attachment posts.
• Center punch the marked hole locations. Drill 1/4" pilot
holes from the appearance side through the entire panel
thickness.
• Use a !/2" spade bit to drill 1/4" to 5/16" deep into
the back side of the panel. Insert washer (spacer) into
the hole.
Install screw through the handle standoff and into
the pilot hole.
Fasten nut onto the screw until the standoff is tight
against the panel. The screw hole on the standoff
should be pointing down toward the floor.
• Place handle attachment posts inside the standoffs.
Use the Allen wrench to install the set screws. Tighten
handle to standoffs.
24-7/32"
1_7/8"
Custom
_Framed
/Panel
Handle
S;andoff
//
_crew
30"
- Tubular
Handle
-- Handle
....... Attachment
Post
- Set
Screw
Notes
10
Notes
11
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram ®local service in gour area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance
and specifications are subject to change without notice.
Pub. No. 51-5!544-5
Part No. !97D589]P002
08-07 JR
Printed in 81ovenio
GEConsumer & Industrial
Appliances
General Electric Company
Louisville, KV/40225
ge.com
