GEMMY 112718 Lightshow SmartLights Personalized Projection User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3845476
Application ID	3PkM7UaljmEObfHAZshocA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.3kB (166311 bits)
Date Submitted	2018-05-10 00:00:00
Date Available	2018-05-10 00:00:00
Creation Date	2018-04-16 19:47:28
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-05-10 10:10:33
Document Title	User manual
Document Creator	Adobe InDesign CC 2017 (Macintosh)

INSTRUCTIONS
IMPORTANT: PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE USING THIS PRODUCT.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
WARNING: Not recommended for children under 12 years of age. As with all electric products, precautions
should be observed during handling and use to prevent electric shock.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN THE COVER. NO USER
SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING: This product is recommended for indoor and outdoor use. Please read this manual
carefully prior to using the unit.
WARNING:
1. This is an electric product – not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played
with or placed where small children can reach it.
2. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used
in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided,
contact a qualified electrician for proper installation.
3. This seasonal use product is not intended for permanent installation or use.
4. Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
5. Unplug the product when leaving the house, or when retiring for the night, or if left unattended.
6. Do not use this product for other than its intended use.
7. Do not hang ornaments or other objects from cord, wire, or light string
8. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not use with an extension cord unless plug can be fullyinserted. Do not alter or replace
the plug. It is acceptable to omit this item if the product does not employ a polarized plug.
9. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or Nails
10. Do not let lamps rest on the supply cord or on any wire.
11. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
12. Do not cover the product with cloth, paper or any material not part of the product when in use.
13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse
blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the
product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check
the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.
15.For indoor and outdoors use .use A/C power for the unit.
CAUTION: To reduce the risk of fire and electric shock:
1. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal.
2. Do not mount or support wires in a manner that can cut or damage wire insulation.
E-1
SAVE THESE INSTRUCTIONS USE AND CARE INSTRUCTIONS
USER SERVICING INSTRUCTIONS
1. When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in
which the needles are brown or break off easily. Keep the tree holder filled with water.
2. If the product is placed on a tree, the tree should be well secured and stable.
3. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
4. When storing the product, carefully remove the product from wherever it is placed, to avoid any undue strain or stress
on the product conductors, connections, and wires.
5. When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICING INSTRUCTIONS
WARNING: Remove all plastic fasteners and tags. These are part of the packaging and should be discarded.
TECHNICAL SPECIFICATIONS
Fuse:
2pcs
Stake
1pc
Rating
120VAC 60Hz 0.27A 20W
ASSEMBLY INSTRUCTIONS
1. G
 ently remove contents from packaging and lay out in a clear area.
2. Push A through the circle, insert the grooves of projector, and tighten the
circle, then adjust the angle of projector. ( illustration 1)
3. S
 take for outdoor use. Built-in tripod for indoor use. (illustration 2)
Illustration 1
Illustration 2
Illustration 3
Illustration 4
4. Plug power cord into standard wall socket. ( illustration 3)
5. Turn dial to focus. ( illustration 4)
6. Unplug when not in use.
USER SERVICING INSTRUCTIONS
Fuse Replacement
WARNING: Risk of Fire: Replace only with same size and type of fuse.
WARNING: Risk of Fire: Do not replace the attachment plug. Contains
a safety device (fuse) that should not be removed. Discard product if attachment plug is
damaged.
1.G
 rasp plug and remove from the receptacle or other outlet device. Do not unplug by
pulling on the cord.
2. Open fuse cover. Slide open the fuse access cover on top of the attachment plug
towards blades. (See illustration)
3. Remove fuses carefully.
4. R
 eplace fuse only with 5 Amp Max, 125 Volt fuse (provided with product).
E-2
Working
Fuse
Replace
Fuse
5. C
 lose the fuse cover. Slide closed the fuse access cover on top of the attachment plug.
BATTERY USAGE:
See illustration. 1. Keep these instructions for future reference because they contain important information. 2. May explode
or leak and cause burn injury if recharged, disposed of in fire, mixed with a different battery type, inserted backwards or
disassembled. 3. Products that contain batteries should not be disposed of in fire. The batteries inside may explode or
leak. 4. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. 5. Do not mix old and
new batteries. Replace all batteries of a set at the same time. 6. Use only batteries of the same or equivalent type as
recommended by the manufacturer. 7. Be sure to insert batteries with correct polarities and always follow manufacturers’
instructions. 8. Remove exhausted batteries from product promptly. 9. Do not short-circuit supply terminals. 10. Remove
batteries before storage or extended periods of non-usage. 11. Clean the contacts on the batteries and the device prior to
battery installation. Nonrechargeable batteries are not to be recharged. Rechargeable batteries are not recommended for
use in this product. If rechargeable batteries are being used, however, please follow these guidelines. (1). Rechargeable
batteries should be removed from the product before being charged. (2). Rechargeable batteries should only be charged
under adult supervision.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause armful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any interference received,including interference that may
cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and
your body.
THIS INSTRUCTION SHEET APPLIES TO ITEM NUMBER
112718
113015
QD ID: 96230
Visit WWW.GEMMY.COM for more information.
©2018 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE. SUITE 100
COPPELL, TX 75019 U.S.A.
1 (877) 250-9032
MADE IN CHINA / PRINTED IN CHINA
E-3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2018:04:16 19:47:28+08:00
Creator                         : Adobe InDesign CC 2017 (Macintosh)
Modify Date                     : 2018:05:10 10:10:33+08:00
Language                        : zh-TW
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Instance ID                     : uuid:e79d74a7-a258-490d-9bd5-28fcb055ca48
Original Document ID            : adobe:docid:indd:9a50b753-105a-11df-aee7-a7b1d14b906f
Document ID                     : xmp.id:6eaacbd9-afc3-47ef-8034-dde4c2046c7e
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:7a4baee5-eef2-4211-82b4-be38cae6dea5
Derived From Document ID        : xmp.did:35a2a3cb-79ac-4e4c-b15a-06e992ed907e
Derived From Original Document ID: adobe:docid:indd:9a50b753-105a-11df-aee7-a7b1d14b906f
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Macintosh)
History Changed                 : /
History When                    : 2018:04:16 19:47:28+08:00
Metadata Date                   : 2018:05:10 10:10:33+08:00
Creator Tool                    : Adobe InDesign CC 2017 (Macintosh)
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 3

EXIF Metadata provided by EXIF.tools