GEMMY 75240 AppLights Projection User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3312001
Application ID	L9xD46xujHHdwxgaNcsf0w==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.22kB (302703 bits)
Date Submitted	2017-03-10 00:00:00
Date Available	2017-03-13 00:00:00
Creation Date	2017-12-25 12:58:44
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-25 12:58:44
Document Title	User manual
Document Creator	Adobe InDesign CC (Macintosh)

INSTRUCTIONS
E pg.1
Congratulations! You are now the proud owner
of a LED LIGHTSHOW. Please read the directions carefully before
use.
SAFETY WARNING:
Remove all plastic fasteners and tags. These are part of the packaging and should be discarded.
SAVE THESE INSTRUCTIONS –
This
manual contains important safety and operating instructions for
power units.
WARNING
ELECTRIC PRODUCT. Keep away from children. Not recommended for children
under 3 years of age. As with all electrical products, precautions should be observed
during handling and use to reduce the risk of electric shock. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualiied
persons in order to avoid a hazard.
WARNING
Strobe lights have been known to trigger seizures in people with photosensitive
epilepsy.
WARNING
The light is very bright. Do not shine directly into eyes.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL PRODUCTS,
BASIC PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED INCLUDING THE FOLOWING: READ ALL INSTRUCTIONS BEFORE
pg.2
USING(THIS FURNISHING)
WARNING: TO REDUCE THE RISK OF
BURNS, FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS ：
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. Do not secure the wiring of the product with staples or nails, or place on sharp
hooks or nails.
2. Do not let lamps rest on the supply cord or on any wire.
3. Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
4. Do not cover the product with cloth, paper or any material not part of the product
when in use.
5. Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided,
contact a qualiied electrician for proper installation.
6. This seasonal use product is not intended for permanent installation or use.
7. Do not mount or place near gas or electric heaters, ireplace, candles or other
similar sources of heat.
8. Unplug the product when leaving the house, when retiring for the night, or if left
unattended.
9. This is an electric product-not a toy! To avoid risk of ire, burns, personal injury
and electric shock it should not be played with or placed where small children can
reach it.
10. Do not use this product for other than its intended use.
11. Do not hang ornaments or other objects from cord, wire, or light string.
12. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet.
Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product.If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
13. This product has a polarized plug (one blade is wider than the other) as a feature
to reduce the risk of electric shock. This plug will it in a polarized outlet only one
way. If the plug does not it fully in the outlet, reverse the plug. If it still does not it,
contact a qualiied electrician. Do not use with an extension cord unless plug can
be fully inserted. Do not alter or replace.
pg.3
14. Read and follow all instructions that are on the product or provided with the product.
CAUTION:
To reduce the risk of ire and electric shock:
1. Do not install on trees having needles, leaves or branch coverings of metal or
materials which look like metal.
2. Do not mount or support wires in a manner that can cut or damage wire insulation.
SAVE THESE INSTRUCTIONS.
FEATURES
- Plastic housing with 4 pieces high power LEDs.
- UL power cord operated.
- Easy installation.
- High quality, long product life.
TECHNICAL SPECIFICATIONS
Material:
Light sourcing:
PC
1W LED * 1
Fuse
2 pcs
Stake
1 pc
3W LED * 3
ASSEMBLY INSTRUCTIONS
1. Gently remove contents from packaging and lay out in a
clear area.
2. Assemble the light stake parts A & B as shown in illustration 1 , Push the A and B parts together until tighten the
screws.
3. Push A through the circle, insert the grooves of projector,
and tighten the circle, then adjust the angle of projector.
illustration 1
pg.4
4. Plug power cord into standard wall socket. ( illustration 2)
5. Unplug when not in use.
illustration 2
USER SERVICING INSTRUCTIONS
Fuse Replacement
WARNING：R isk of Fire: Replace only with same
size and type of fuse.
WARNING：Risk of Fire: Do not replace the attach-
ment plug. Contains a safety device (fuse) that should not be
removed. Discard product if attachment plug is damaged.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on the cord.
2. Open fuse cover. Slide open the fuse access cover on top of the attachment plug
towards blades. (See illustration)
3. Remove fuse carefully.
4. Replace fuse only with 5 Amp Max, 125 Volt fuse (provided with product)
5. Close the fuse cover. Slide closed the fuse access cover on top of the attachment
plug.
OPERATING DETERMINATIONS
This product was designed for indoor and outdoor use.
Do not shake the device. Avoid brute force when operating the device.
Keep away from direct insulation (particularly in cars) and heaters.
Do not permit operation by persons not qualiied to operating the device. Most damages are the result of unprofessional operation!
Never use solvents or aggressive detergents in order to clean the device! Rather use
a soft and damp cloth. Please use the original packaging if the device is to be transported. Unauthorized modiications on the device are unacceptable due to safety
reasons! If this device is operated in any way different from the ways described in this
manual, the product may suffer damages and the guarantee becomes void.
pg.5
OPERATION
- Insert the plug into socket.
- Set this device as a projector.
- Extract the plug if not in use. Be careful with the power cord!
WARNING
• The device is for indoor and outdoor use!
• Suitable for outdoor use!
• Please keep away from heaters and other heating sources!
IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems. Keep away
from heaters and other heating sources! If the device has been exposed to drastic
temperature luctuation (e.g. after transportation), do not switch it on immediately.
Leave the device switched off until it has reached room temperature. Please note that
damages caused by manual modiications on the device or unauthorized operation
by unqualiied persons are not subject to warranty. Keep young children and amateurs away from the device!
USE AND CARE INSTRUCTIONS
1. When the product is placed on a live tree, the tree should be well maintained and
fresh. Do not place on live trees in which the needles are brown or break off easily.
Keep the tree holder illed with water.
2. If the product is placed on a tree, the tree should be well secured and stable.
3. Before using and reusing, inspect the product carefully. Discard any products that
have cut, damaged or frayed wire insulation cords, cracks, lamp holders or enclosures, loose connections, or exposed copper wire.
4. When storing the product, carefully remove the product from wherever it is placed,
including trees, branches, or bushes, to avoid any undue strain or stress on the
product conductors, connections and wires.
5. When not in use, store neatly in a cool, dry location protected from sunlight.
CAUTION:
Changes or modiications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
pg.6
WARNING
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
NOTE:
The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modiications to this equipment. Such modiications could
void the user’s authority to operate this equipment.
WARNING
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
RF RADIATION EXPOSURE STATEMENT
The device has been evaluated to meet FCC and RSS-102 general RF exposure
requirement.
CAUTION
1) For temporary (90 days max.) installation and use only.
2) Toreduce the likelihood of excessive heat and possible damage, use only decorative
lamp accessories packaged with this product.
3) To reduce the risk of ire or electric shock, do not attempt to replace lamps or modify
product.
4) This is an electric product-not a toy! To avoid risk of ire, burns, personal injury and
electric shock it should not be played with or placed where small children can reach
it.
5) To prevent electric shock, match wide blade of plug to wide slot, fully insert.
6) Do not connect to another lighting string, decorative outit or seasonal product.
7) Always unplug this product before installing or replacing fuses.
8) Do not place near standing areas of water,such as ponds and pools.
THESE INSTRUCTIONS ARE FOR ITEM
75238
QD ID: 71866
75240
Visit WWW.GEMMY.COM for more information.
©2017 GEMMY INDUSTRIES CORP.
117 WRANGLER DRIVE. SUITE 100
COPPELL, TX 75019 U.S.A.
1 (877) 250-9032
MADE IN CHINA
PRINTED IN CHINA

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:7583321b-9f45-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:12 17:38:26Z
Create Date                     : 2017:07:12 17:38:26Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:7583321b-9f45-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled

EXIF Metadata provided by EXIF.tools