GIANT RIDE-SENSE-G1 RIDE SENSE SENSOR User Manual 1

Giant Manufacturing Co., Ltd. RIDE SENSE SENSOR 1

Users Manual

RideSenseRideSenseSpeed magnetCadence magnetHex bolt: 1xRideSense: 1xSpeed magnet: 1xRound Head Screw: 1xWasher: 1xCadence magnet: 1xZip tie: 2xCR2032 1xGiant RideSense is an integrated ANT+ sensor system available on the following Giant performance bicycle frames:• TCR Advanced SL • Defy Advanced SL • Avail Advanced• TCR Advanced • Defy Advanced • Trinity CompositeGiant RideSense is compatible with computers featuring ANT+ wireless technology.
2. Install RideSenseMax: 0.4N-m342.5 mm Hex Key1. RideSense SpecificationsProduct characteristicDescriptionAuto-activationActivated automatically if magnet has passed the sensor twice in 5 seconds.The sensor lights will flash for 0.2 seconds when the magnet passes the sensor for first 10 times.Sleeping modeRideSense goes into Sleeping Mode if there is no signal for 20 minutes.Energy saving360 hours battery lifespan.WirelessFully compatible with ANT+ wireless technology Speed sensor light Cadence sensor lightSpeed sensor Cadence sensor215
4. Assemble speed magnetThe clearance between speed magnet and RideSense should be 2~10 mm. To meet this requirement you can reverse the speed magnet to get more clearance .2~10mmChain StayWheel3. Assemble pedal cadence magnetInner side of left crankPosition at 128mm from the center of bottom bracket1. Remove the tape from magnet and stick it onto inner inside of the crank .2. Fix it by using the zip ties.3. Rotate crank to test if it activates the cadence sensor (flashing red light).3mm Hex keyMax: 0.5N-mBack RideSenseFront side facing towards RideSenseFrontBack side facing towards RideSenseRideSense
5. Uninstall RideSense 6. Replacing the batteryOpenCloseCR2032 batteryPress the plugs into the Sensor mount openings.123Pulling RideSense out of the frame vertically can cause damage to the sensor.WARNING
RideSenseRideSense速度感應座迴轉感應座1xRideSense: 1x速度感應座: 1x半圓頭螺絲:1x墊片: 1x迴轉感應座: 1x束節帶: 2xGiant RideSense 設計能整合安裝於特定Giant 系列公路車，如TCR Advanced SL。Giant RideSense 能相容於內建ANT+無線技術之車用碼表。CR2032 1x
2. 安裝RideSense0.4N-m342.5 mm 六角扳手1. RideSense SpecificationsProduct characteristicDescription自動啟動迴轉或速度感應座於5秒內通過感應區兩次以上時，將自動喚醒RideSense。RideSense於感應到迴轉或速度訊號時，感應燈將亮起0.2秒，持續10次。睡眠模式連續20分鐘內無訊號變化，系統會進入睡眠模式以節省電力消耗。節能省電約360小時的電池壽命。無線科技完全相容於ANT+ 無線技術。速度感應燈(綠)迴轉感應燈(紅)速度感應區 迴轉感應區215
4. 安裝速度感應座速度感應座與RideSense之間隙應保有 2~10 mm。為滿足上述之間隙距離，您可反轉速度感應座以感應座背面向 RideSense以取得較多的組配間隙。2~10mm後下叉輪組3. 安裝踏板迴轉感應座左曲柄內側固定位置：迴轉感應座距離五通中心約128mm。1. 移除感應座背面貼紙，並黏貼於左曲柄背面之適當位置如左圖所示。2. 使用束節帶固定迴轉感應座.3. 轉動曲柄測試是否能正常啟動 RideSense(閃紅燈)。3mm 六角扳手0.5N-m感應座背面 RideSense速度感應座正面朝RideSense感應座正面速度感應座背面朝RideSenseRideSense
5. 移除RideSense 垂直使力拉出RideSense將可能造成RideSense或車架斷裂或損壞。注意6. 更換電池開關CR2032 電池將塑膠塞置入 RideSense安裝位。123
8. Statement 聲明警語7. Certifications 認證FCC StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.Changes or modifications to this device not expressly approved by the party responsible for compliance with FCC regulations (the manufacturer) could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged t o try to correct the interference by on or more of the following measures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.4. Consult the dealer or and experienced radio technician for help.CE-Mark WarningIn a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.IC statementThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.DGT警語經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Navigation menu