GL Technologies 300NV2 Smart Router User Manual GL MT300N V2

GL Technologies (Hong Kong) Limited Smart Router GL MT300N V2

Users manual

Download: GL Technologies 300NV2 Smart Router User Manual GL MT300N V2
Mirror Download [FCC.gov]GL Technologies 300NV2 Smart Router User Manual GL MT300N V2
Document ID3409658
Application IDO4285QbKFXSD+bmm2IKRfQ==
Document DescriptionUsers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize6.19kB (77369 bits)
Date Submitted2017-05-31 00:00:00
Date Available2017-05-31 00:00:00
Creation Date2017-05-22 17:17:50
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2017-05-22 17:17:50
Document TitleMicrosoft Word - User manual GL-MT300N-V2
Document CreatorPScript5.dll Version 5.2
Document Author: Administrator

GL-MT300N-V2 User manual
Introduction
Congratulations on receiving your GL-MT300N-V2. As part of our Green Initiative, we do not include printed
user documentation with our product packaging. This policy saves paper, lowers shipping costs, reduces carbon
emissions and results in a cleaner environment.
Documentation
All product and accessory documentation can be found at the GLI Support Centre: http://www.gl-inet.com/docsOn
this site you will gain access to GLI technical resources and information about GLI products. To use your new GLI
Mini Router you will need to follow the simple steps which you can see from
http://www.gl-inet.com/docs/wiki/#!mini/index.md
Default System Settings
Product
LAN Default IP Address
LAN Fall-back IP Address
GL-MT300N-V2
DHCP
192.168.8.1
Initial Set-up
Interfaces described as followed:
Power to the GLI Mini Router is provided by connect the power lead (supplied) to the power adaptor (buy
separately) and then to the power interface on the GLI Mini Router.
Once power is provided to the GLI Mini Router the LED’s will provide status on its operation based on the
following:
LED
Indicator
Description
LED 1 (Power)
Green solid
Power is applied
LED 2 (Customized)
Customized
This is customized LED.
LED 3 (WiFi connection)
Red
Indicates WiFi signal (solid) and
data transfer (flashing).
Button Definition
z
Press the Reset button to toggle the WiFi signal ON or OFF.
Press and hold the Reset button for at least 8 seconds, then release your finger to reset the router to factory
default state. Wait until the router reboots, which could take about 3 minutes.
The function of “switch” is configurable by user.
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the users’ authority to operate the equipment.
FCC Caution
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNNING: The minimum separation generally be used is at least 20 cm,
even if the calculations indicate that the MPE distance would be lesser.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2017:05:22 17:17:50+08:00
Create Date                     : 2017:05:22 17:17:50+08:00
Format                          : application/pdf
Title                           : Microsoft Word - User manual GL-MT300N-V2
Creator                         : Administrator
Document ID                     : uuid:86d43447-5f27-447b-97dc-04505e1e44bc
Instance ID                     : uuid:6d2e4fb0-20bb-46c0-a76a-a4ddd631fe04
Page Count                      : 2
Author                          : Administrator
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AFIW-300NV2

Navigation menu