GN Audio USA GNELLIPSE24 GN Ellipse 2G4 Wireless Headset User Manual GNN ELLIPSEPRELIM qxp

GN Netcom Inc GN Ellipse 2G4 Wireless Headset GNN ELLIPSEPRELIM qxp

users manual

For More Information:Pour Plus de Détails:Para Más Información:Para Obter Informações Adicionais: www.gnnetcom.comCORPORATE HEADQUARTERS77 Northeastern Blvd.Nashua, NH • 030621-800-826-46561-603-598-1100Fax: 1-603-598-1122© 2001 GN Netcom, Inc. • All rights reserved.Preliminary • Printed in the U.S.A.GN Ellipse 2.4Wireless Headset System** Charge battery for 3 hours prior to initial use.User GuideEllipse Components1 Remote Backpack2Base3Base Stand4Headset Holder5 Headset (included with System purchase or as an option)6AC Power Adapter7Telephone Cord8Remote Battery9Remote Handset Lifter(included with System purchase or as an option)10 Pocket Clip11 Belt Clip12 Lanyard123456791181012
65Remote Beltpack Functions1Headset Mode Indicator:Blinks when the system is in headset mode; no light in handset mode.2Volume Control:Press + to increase volume. Press - to decrease volume.3Mute Button:Press to activate Mute and disable the transmit/microphone; press again to enable transmit/microphone.4Headset/Handset & Remote Handset Lifter Buttons:Press to enter headset or handset mode as desired (lights on remote and base light in head-set mode); press again to answer a call with the Remote Handset Lifter (optional).Base Functions/Indicators5Transmit Settings:Adjusts the volume of your voice.6Telephone Compatibility Settings:Fine tunes the system to your telephone system.7Battery Charge Indicator:Lights when the remote is properly seated in the base charger.8Headset Mode Indicator:Lights when the system is in headset mode; no light in handset mode.234187Discharging the BatteryFor optimum Battery life, completely discharge the Battery approximately every 6 months. TheDischarge/Recharge cycle takes approximately 2 hours. Removing the Remote from the Base duringdischarge cancels the operation. Only one Battery can be placed in the Base while discharging.A. Slide the Remote into the Charger on either side of the Base. B. Simultaneously press the Mute and Headset/Handset buttons for 5 seconds. The Headset Mode andBattery Charger Indicators will flash alternately during discharge. When fully discharged, the Batteryautomatically recharges. Recharging the BatterySlide the Remote into the Charger on either side of the base. To use your Headset while charging,put the System in Headset Mode. To charge overnight, put the System in the Handset Mode.Audio IndicatorsMuteOut of RangeLow BatteryVolumeTone sounds in headset every 3 seconds.Tone sounds in headset every 10 seconds.Tone sounds in headset every 20 seconds.Tone sounds in headset at maximum and minimum range.Nickel Metal Hydride (NiMH), 3.6 V 500 mAH (GN Netcom part number 27381101).Fully charged battery provides minimum of 12 hours continuous use without recharging.The base has twocharging ports; additional battery can be purchased for24/7 operation.Fully charged battery provides minimum 80 hours without recharging.Maximum 3 hours to completely recharge a discharged battery; battery cannot be overcharged.2 years if battery is recharged when not in use and never completely discharged.Battery InformationBattery TypeCapacity On-LineCapacity Off-LineRecharging TimeBattery Life
Connect all cords.Attach the Base Stand.Attach the Headset Holder.Attach the Battery to the Remote.1. 2.3.4.Slide the Remote into the Chargeron either side of the Base. TheBattery Charge light on the side ofthe Base illuminates. Charge theBattery for a full 3 hours. Use theHandset while the Battery charges.6.7. Setting Up5. Connect the Headset to the Remote.8. Make sure the Mute is off.When Mute is on, a tone sounds in theHeadset every 3 seconds. 9. Put the Headset on and select atelephone compatibility settinguntil dial tone is clear. If dialtone is clear for both A and G,set to A.10. Remove the Handset and make a call. While switchingbetween the Headset andHandset, adjust the transmit (microphone) setting until your voice is the same volumeon both devices (1 is the softest,8 is the loudest). Most settingsare 5-7. If the best setting is 7or 8, change the telephonecompatibility setting to G.Disconnect the optional Remote HandsetLifter from the Base while setting the volume.Put the System in Headset Mode.The Headset Mode light on thetop of the Remote blinks, and theHeadset Mode light on the side ofthe Base illuminates. It will take up to 45 seconds to establish achannel with first use.11. Use the Remote Beltpack to adjustthe receive (speaker) volume. If your telephone has volume control,set it to mid-range. 21
To roam up to 200 ft. (150 m) from the base, remove theRemote from the Base Chargerand clip it to your belt or pocket, orwear it with the Lanyard.12. Using The Remote13. Pocket Clip.14. Belt Clip.15. Lanyard.FAQsWhat should I check if I don’t hear a dial tone?• Check to see that all cords and jacks are connected• Make sure that the Headset cord is fully inserted into the remote• Make sure that the AC Adapter is plugged in and has power• Try the compatibility setting on A and G• Make sure the system is in Headset Mode• Make sure that the Battery is properly installed in the beltpack• Make sure that the Battery is fully charged (3 hours minimum)• Check that the serial numbers on the bottom of the Base unit and back of Beltpack units match; because of the security circuits, the Beltpack and Base unit must match for operationWhat should I check if the other party has a hard time hearing me?• Make sure the Mute on the Beltpack is off• Increase the transmit level (1 is the softest, 8 is loudest)• Check the position of the headset Microphone and make sure that it is placed at the corner of your mouthWhat should I do if I hear a buzz or humming sound in my Headset?• Move the Base farther away from the telephoneWhat should I do if I hear an echo in my headset while speaking?• Lower your transmit adjustment. If this makes the transmit too weak, try adjusting the Telephone Compatibility Switch settingWhat should I do if I hear noise or static or if the signal is weak?• You may be out of range; move closer to the Base for a stronger signalDo I need to lift the handset to make calls?• Some telephone systems allow on-hook dialing; refer to your telephone system user guide for instructionsAccessories The Remote Handset Lifter lifts the Handset from your telephone enabling you to answer and hang up calls without returning to your desk.The Remote Handset Lifter lifts the Handset from your telephone enabling you to answer and hang up calls without returning to your desk.The Remote Handset Lifter lifts the Handset from your telephone enabling you to answer and hang up calls without returning to your desk.The Remote Handset Lifter lifts the Handset from your telephone enabling you to answer and hang up calls without returning to your desk.Remote Handset LifterRemote Handset LifterRemote Handset LifterRemote Handset LifterAdjusting Remote Beltpack Buzz VolumePut the System in Handset Mode.Simultaneously press the upper and lower parts of the Volume Button as well as the Mute Button. The Headset Mode Indicator light on the remote lights up indicating you are in buzzer setting mode. Press the Volume Button (+ or -) to cycle through the four available options:Maximum Volume, Medium VolumeMinimum Volume, Buzzer Muted.Release the Volume Button when the desired setting is reached. Within 5 seconds, the setting will be stored and the Headset Mode Indicator light will go out.To prolong operating time from 12 to 24 hours, an additional Battery can be purchased. (GN Netcom part number 27381101). To prolong operating time from 12 to 24 hours, an additional Battery can be purchased. (GN Netcom part number 27381101). To prolong operating time from 12 to 24 hours, an additional Battery can be purchased. (GN Netcom part number 27381101).To prolong operating time from 12 to 24 hours, an additional Battery can be purchased. (GN Netcom part number 27381101).BatteryBatteryBatteryBattery

Navigation menu