GODOX PHOTO EQUIPMENT XPRO TTL Wireless Flash Trigger User Manual 1

GODOX PHOTO EQUIPMENT CO.LTD TTL Wireless Flash Trigger 1

Users Manual

说明手册
Instruction Manual
705-XPRZC0-00 Made In China
地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋
Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong
Town, Baoan District, Shenzhen 518103, China
电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423
邮箱/E-mail: godox@godox.com
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
TTL无线引闪器
TTL Wireless Flash Trigger
Foreword
Warning
Names of Parts
Body
LCD Panel
Battery
Installing Batteries
Battery Level Indication
Using the Flash Trigger
As a Wireless Camera Flash Trigger
As a Wireless Outdoor Flash Trigger
As a Wireless Original Flash Trigger
As a Wireless Studio Flash Trigger
As a Wireless Shutter Release Trigger
As a Flash Trigger
with 2.5mm Sync Cord Jack
Setting the Flash Trigger
Power Switch
Automatically Enter Power Saving Mode
Power Switch of AF Assist Beam
Channel Settings
Wireless ID Settings
Mode Settings
Magnification Function
Output Value Settings
Flash Exposure Compensation
Settings
Multi Flash Settings
(Output Value, Times
and Frequency)
Modeling Lamp Settings
ZOOM Value Settings
Shutter Sync Settings
Buzz Settings
Sync Socket Settings
TCM Function
SHOOT Function Settings
C.Fn: Setting Custom Functions
Compatible Flash Models
Compatible Camera Models
Technical Data
Restore Factory Settings
Firmware Upgrade
Attentions
Caring for Flash Trigger
Contents Foreword
Thanks for your purchase of this XProC wireless flash trigger.
This wireless flash trigger is suitable for using Canon cameras to control Godox
flashes with X system e.g. camera flash, outdoor flash, and studio flash. It can also
control Canon original speedlites with the coordination of X1R-C receiver. Featuring
multi-channel triggering, stable signal transmission, and sensitive reaction, it gives
photographers unparalleled flexibility and control over their strobist setups. The flash
trigger applies to hotshoe-mounted Canon EOS series cameras, as well as the
cameras which have PC sync sockets.
With XProC wireless flash trigger, high speed synchronization is available for most of
camera flashes in the market which support E-TTL II. The max flash synchronization
speed is up to 1/8000s *.
*: 1/8000s is achievable when the camera has a max camera shutter speed of 1/8000s.
- 23 - - 24 -
24
25
26
28
28
34 44
45
46
47
47
48
48
Warning
Do not disassemble. Should repairs become necessary, this product must be sent to
an authorized maintenance center.
Always keep this product dry. Do not use in rain or in damp conditions.
Keep out of reach of children.
Do not use the flash unit in the presence of flammable gas. In certain circumstance,
please pay attention to the relevant warnings.
Do not leave or store the product if the ambient temperature reads over 50℃.
Turn off the flash trigger immediately in the event of malfunction.
Observe precautions when handling batteries
- Use only batteries listed in this manual. Do not use old and new batteries or
batteries of different types at the same time.
- Read and follow all warnings and instructions provided by the manufacturer.
- Batteries cannot be short-circuited or disassembled.
- Do not put batteries into a fire or apply direct heat to them.
- Do not attempt to insert batteries upside down or backwards.
- Batteries are prone to leakage when fully discharged. To avoid damage to the
product, be sure to remove batteries when the product is not used for a long time or
when batteries run out of charge.
- Should liquid from the batteries come into contact with skin or clothing, rinse
immediately with fresh water.
Names of Parts
Body
Power Switch
--ON (Power On)
--OFF (Power Off)
AF Assist Beam Switch
--ON (AF Assist Beam outputs)
--OFF (AF Assist Beam
do not output)
Battery Compartment
Hot Shoe Camera Connection
LCD Panel
Status Indicator Lamp
--Green:
Trigger (Flash) +
Focus (Camera)
--Red:
Trigger (Flash) +
Shutter (Camera)
Group Button 1
Group Button 2
Group Button 3
Group Button 4
Group Button 5
Function Button 2
Function Button1
Function Button 3
Function Button 4
MODE/LOCK Mode Selection/
Locking Button
TEST/Shutter Button
MENU Button
Magnification/TCM Button
Select Dial
2.5mm Sync
Cord Jack
Type-C USB
Port
AF-assist Lamp
- 25 - - 26 -
CH1
A
B
C
D
E--
M1/16 + 0.3
--
--
--
Zm/CH SYNC ALL MOD
1
7
8
6
9
4 5
3
10
12
32
LCD Panel
(1) Multi Groups
Display
1. Channel (32) 2. Camera Connection 3. Modeling Lamp Master Control
4. High-Speed/Rear Curtain Sync 5. Sound 6. Battery Level Indication
7. Group 8. Mode 9. Power 10. Group’s Modeling Lamp 11. ZOOM Value
12. Icons of Function Button 13. C.Fn Menu 14. Version
CH1
A
B
C
D
E--
M
Zm/CH SYNC ALL MOD
1/128
--
--
--
CH19
AM
Zm/CH SYNC Gr MOD
1/128
Zoom 35 mm
C.Fn
CLEAR
Ver 9.2
BEEP
MIN
LIGHT
STBY
ON
OFF
zzz
CH19
Zm/CH SYNC MOD
Zoom 28
A
B
C
D
E
Zoom 24
Zoom 24
Zoom 24
Zoom 24
13 14 1111
(4) Multi Groups’ ZOOM
Display
(2) Single Group
Display
(3) Menu
Names of Parts
Installing Batteries
As shown in the illustration, slide the battery
compartment lid of the flash trigger and insert two
AA batteries separately.
Battery Indication
Check the battery level indication on the LCD panel
to see the remaining battery level during the usage.
Battery
AA alkaline batteries are recommended.
- 27 - - 28 -
Battery Level Indication
3 grids
2 grids
1 grid
Blank grid
Blinking
Meaning
Full
Middle
Low
Low battery, please replace it.
< 2.5V The battery level is going
to be used out immediately (please
replace new batteries, as low power
leads to no flash or flash missing in
case of long distance).
1. As a Wireless Camera Flash Trigger
Take TT685C as an example:
1.1 Turn off the camera and mount the transmitter on camera hotshoe. Then, power
on the flash trigger and the camera.
Using the Flash Trigger
The battery indication only refers to AA alkaline batteries. As the voltage of Ni-MH battery tends to be
low, please do not refer to this chart.
1.2 Long press the <Zm/CH> button to set
channel, group, mode and parameters (refers
to the contents of “Setting the Flash Trigger”).
1.3 Turn on the camera flash, press the
wireless setting button and the wireless
icon and <SLAVE> slave unit icon will be
displayed on the LCD panel. Press the <CH>
button to set the same channel to the flash
trigger, and press the <Gr> button to set the
same group to the flash trigger (Note: please refer to the relevant instruction manual when
setting the camera flashes of other models).
1.4 Press the camera shutter to trigger and the status lamp of the flash trigger
turns red synchronously.
Using the Flash Trigger
2. As a Wireless Outdoor Flash Trigger
Take AD600B as an example:
2.1 Turn off the camera and mount the
transmitter on camera hotshoe. Then,
power on the flash trigger and the
camera.
2.2 Long press the <Zm/CH> button to set
channel, group, mode and parameters
(refers to the contents of “Setting the
Flash Trigger”).
2.3 Power on the outdoor flash and press the wireless setting button and the
wireless icon will be displayed on the LCD panel. Long press the
Using the Flash Trigger
3. As a Wireless Original Flash Trigger
Take 600EX-RT as an example:
3.1 Turn off the camera and mount the transmitter
on camera hotshoe. Then, power on the flash
trigger and the camera.
3.2 Long press the <Zm/CH> button to set channel,
group, mode and parameters (refers to the
contents of “Setting the Flash Trigger”).
3.3 Attach the original flash to the X1R-C receiver.
Press the <CH> button on the receiver to set
the same channel to the flash trigger, and press
the <Gr> button to set the same group to the
flash trigger (Note: please refer to the relevant
instruction manual when setting the original
camera flashes).
3.4 Press the camera shutter to trigger. And the
status lamp of the camera flash and the flash
trigger both turn red synchronously.
GR
CH
- 30 -- 29 -
< >
< >
< >
< >
<GR/CH> button to set the same channel to the flash trigger, and short press
the < GR/CH> button to set the same group to the flash trigger (Note: please
refer to the relevant instruction manual when setting the oudoor flashes of other
models).
2.4 Press the camera shutter to trigger and the status lamp of the flash trigger turns
red synchronously.
Using the Flash Trigger
4. As a Wireless Studio Flash Trigger
Take GS400II as an example:
4.1 Turn off the camera and mount the transmitter
on camera hotshoe. Then, power on the flash
trigger and the camera.
4.2 Long press the <Zm/CH> button to set
channel, group, mode and parameters (refers
to the contents of “Setting the Flash Trigger”).
4.3 Connect the studio flash to power source and
power it on. Synchronously press down the
<GR/CH> button and <S1/S2>button and the
wireless icon will be displayed on the
LCD panel. Long press the <GR/CH> button to
set the same channel to the flash trigger, and
short press the < GR/CH > button to set the
same group to the flash trigger (Note: please
refer to the relevant instruction manual when
setting the studio flashes of other models).
4.4 Press the camera shutter to trigger. And the
status lamp of the camera flash and the flash
trigger both turn red synchronously.
Note: As the studio flash’s minimum output value is
1/32, the output value of the flash trigger should
be set to or over 1/32. As the studio flash do not
have TTL and stroboscopic functions, the flash
trigger should be set to M mode in triggering.
5. As a Wireless Shutter Release Trigger
Operation method:
5.1 Turn off the camera. Take a camera remote
cable and insert one end into the camera’s
shutter socket and the other end to the
shutter release port of X1R-C to connect.
Power on the camera and the receiver.
5.2 Long press the <Zm/CH> button to set
channel, group, mode and parameters
(refers to the contents of “Setting the Flash
Trigger”).
5.3 Press the receiver’s <CH> button to set the
same channel to the flash trigger, and press
the <Gr> button to set the same group to the
flash trigger.
5.4 Half press the button to focus and full
press the <TEST> button to shoot. Release
the button until the status lamp turns to red.
Using the Flash Trigger
CH
%
- 32 -- 31 -
< >
Setting the Flash Trigger
Slide the Power Switch to ON, and the device is on and status indicator lamp will not
reveal.
Note: In order to avoid power consumption, turn off the transmitter when not in use.
Power Switch
1. The system will automatically enter standby mode after stop operating the
transmitter over 90 seconds. And the displays on the LCD panel disappear now.
2. Press any button to wake up. If the flash trigger is attached to the hot shoe of
CANON EOS camera, half press the camera shutter can also wake the system up.
Note: If do not want to enter power saving mode, press the <MENU> button to enter C.Fn custom
settings and set STBY to OFF.
Automatically Enter Power Saving Mode
Slide the AF-assist beam switch to ON, and the AF lighting is allowed to output.
When the camera cannot focus, the AF assist beam will turn on; when the camera can
focus, the AF assist beam will turn off.
Power Switch of AF Assist Beam
Channel Setting
1. Long press the <Zm/CH> button and the channel value will be chosen.
2. Turn the select dial to choose the appropriate channel. Press the <SET> button
again to confirm the setting.
3. This flash trigger contains 32 channels which can be changed from 1 to 32. Set the
transmitter and the receiver to the same channel before usage.
Using the Flash Trigger
6. As a Flash Trigger with 2.5mm Sync Cord Jack
Operation method:
6.1 The connection method please refers to the
contents of “As a Wireless Studio Flash Trigger”
and “As a Wireless Shutter Release”.
6.2 Press the shutter normally and the flashes will
be controlled by sync cord jack’s signal.
- 34 -- 33 -
Change the wireless channels and wireless ID to avoid interference for it can only be
triggered after the wireless IDs and channels of the master unit and the slave unit are
set to the same.
Press the <MENU> button to enter C.Fn ID. Press the <SET> button to choose OFF
channel expansion shutdown, and choose any figure from 01 to 99.
Note: As the current Godox flashes do not have wireless ID setting functions, please set ID to OFF.
Wireless ID Settings
Mode Setting
Switch between multi-group and one-group mode: choose a group in multi-group mode
and press the <TCM> button to magnify it to one-group mode. Then, press the <TCM>
button to back to multi-group.
Magnification Function
Output Value Settings
1. Short press the <MODE> button, and the mode of the
current group will change.
2. Set the groups to five groups (A-E)
2.1 When displaying multiple groups, press the <MODE>
button to switch the multi-group mode to MULTI mode.
Press the group selection button can set the MULTI
mode to ON or OFF.
2.2 When displaying multiple groups, press the group
selection button or <MODE> button in one-group
mode, and all the current group’s mode will be
changed by the order of TTL/M/--.
3. When setting the group to 16 groups (0-F), there is only
manual mode M.
4. Long press the <MODE> button for 2 seconds until
“LOCKED” is displayed on the bottom of the LCD panel,
which means the screen is locked and no parameters can
be set. Long press the <MODE> button again to unlock.
1. Multi-group displays in the M mode
1.1 Press the group button to choose the group, turn the select dial, and the power
output value will change from Min to 1/1 in 0.3 stop increments. Press the
<SET> button to confirm the setting.
1.2 Press <ALL> button to choose all groups’ power output value, turn the select
dial, and all groups’ power output value will change from Min to 1/1 in 0.3 stop
increments. Press <ALL> button again to confirm the setting.
2. One-group displays in the M mode
Turn the select dial and the group’s power output value will change from Min to 1/1
in 0.3 stop increments.
Note: Min. refers to the minimum value that can be set in M or Multi mode. The minimum value can be
set to 1/128 or 1/256 according to C.Fn-Min. For most of camera flashes, the minimum output value is
1/128 and cannot be set to 1/256. However, the value can change to 1/256 when using in combination
with Godox strong power flashes e.g. AD600, etc.
Setting the Flash Trigger Setting the Flash Trigger
CH1
A
B
C
D
E--
ON
1/64
--
--
--
Zm/CH Times Hz MOD
3 Times
1 Hz
MULTI
CH1
A
C
D
E--
M
--
--
1/64
B M 1/64
Gr Gr
CH1
A
C
D
E--
M
--
--
1/64
B M 1/64
LOCKED
- 36 -- 35 -
Modeling Lamp Settings
1. Multi-group displays in the TTL mode
1.1 Press the group button to choose the group, turn the select dial, and the FEC
value will change from -3 to ~3 in 0.3 stop increments. Press the <SET> button
to confirm the setting.
1.2 Press <ALL> button to choose all groups’ FEC value, turn the select dial, and all
groups’ FEC value will change from -3 to ~3 in 0.3 stop increments. Press
<ALL> button again to confirm the setting.
2. One-group displays in the TTL mode
Turn the select dial and the group’s power output value will change from -3 to ~3 in
0.3 stop increments. 1. When displaying multiple groups, press the <MOD>
button to control the ON/OFF of the modeling lamp.
2. Press the group button to choose the group when
displaying multiple groups or when displaying one-group,
press the <MOD> button to control the ON/OFF of the
modeling lamp (note: The models that can use one-
group to ON/OFF the modeling lamp are as follows:
GSII, SKII, QSII, QDII, DEII, DPII series, etc. The
outdoor flash AD200 and AD600 can use this function
after upgrade. The new arrivals with modeling lamps can
also use this function.).
Flash Exposure Compensation Settings
1. In the multi flash (TTL and M icon are not displayed).
2. The three lines are separately displayed as power output
value, Times(flash times) and Hz (flash frequency).
3. Turn the Select Dial to change the power output value
from Min. to 1/4 in integer stops.
4. Short press the Times button can change flash times.
Turn the select dial to change the setting value.
5. Short press the Hz button can change flash frequency.
Turn the select dial to change the setting value.
Multi Flash Settings (Output Value, Times and Frequency)
Setting the Flash Trigger Setting the Flash Trigger
CH1
A
B
C
D
E--
ON
1/64
--
--
--
Zm/CH Times Hz MOD
3 Times
1 Hz
MULTI
6. Until all the amounts are set. Or during any value setting, short press the <MODE>
button to exit the setting status. No values will blink.
7. In the multi flash setting submenu, short press the <MODE> button to return to main
menu when no values are blinking.
Note: As flash times are restricted by flash output value and flash frequency, the flash
times cannot surpass the upper value that permitted by the system.
The times that transported to the receiver end are a real flash time, which is also
related to the camera’s shutter setting.
CH1
Zm/CH SYNC MOD
A
B
C
D
E
ALL
--
M1/128
--
--
--
- 38 -- 37 -
CH1
Zm/CH SYNC MOD
A
B
C
D
E
ALL
--
TTL
--
--
--
CH1
Zm/CH SYNC MOD
A
B
C
D
E
ALL
--
M
--
--
--
1/128
1. High-speed sync: press the
<SYNC> button and is displayed
on the LCD panel.
2. Second-curtain sync: press the
<SYNC> button and is displayed
on the LCD panel.
Shutter Sync Settings
Press the <MENU> button to enter C.Fn BEEP and press
the <SET> button. Choose ON to turn on the BEEP while
OFF to turn off it. Press the <MENU> button again to back
to the main menu.
Buzz Settings
1. Press the <MENU> button to enter C.Fn SYNC and
press the <SET> button to choose IN or OUT. Press
the <MENU> button again to back to the main menu.
1.1 When choosing IN, this sync socket will enable
XProC to trigger flash.
1.2 When choosing OUT, this sync socket will send
trigger signals to trigger other remote control and
flash.
Sync Socket Settings
TCM transform function is a particular
function that owned by Godox:
TTL flash value transform into
power output value in M mode.
1.1 Set the flash trigger to TTL mode
and attach it to the camera.
Press the shutter for shooting.
1.2 Long press the <TCM> button, and the flash value in TTL mode will
transform into power output value in M mode (The displayed minimum value
is the set Min. value).
1.3 Please refer to the C.Fn setting custom functions to see the flash models
which are compatible with TCM functions.
Note: Please choose the relevant models in TCM function in C.Fn custom settings according
to your own flash.
TCM Function
Setting the Flash Trigger Setting the Flash Trigger
ZOOM Value Settings
Short press the <Zm/CH> button and the ZOOM value will
be displayed on the LCD panel. Choose the group and turn
the select dial, and the ZOOM value will change from
AUTO/24 to 200. Choose the desired value and long press
the <Zm/CH> button again to back to the main menu.
Note: The flash’s ZOOM should be set to Auto (A) mode before
responding.
CH1
Zm/CH SYNC MOD
Zoom 28
A
B
C
D
E
Zoom 24
Zoom 24
Zoom 24
Zoom 24
CH1
A
B
C
D
E--
M1/16 + 0.3
--
--
--
Zm/CH SYNC ALL MOD
CH1
A
B
C
D
E--
M1/16 + 0.3
--
--
--
Zm/CH SYNC ALL MOD
C.Fn Ver 9.2
OFF
ON
CLEAR
MIN
LIGHT
STBY
BEEP
C.Fn Ver 9.2
GROUP
LCD
SHOOT
SYNC
IN
OUT
CLEAR
- 40 -- 39 -
The following table lists the available and unavailable custom functions of this flash.
C.Fn: Setting Custom FunctionsSHOOT Function Settings
Press the <MENU> button to enter C.Fn SHOOT.
Press the <SET> button to choose one-shoot or multi-
shoots, and press the <MENU> button again to back to
the main menu.
One-shoot: When shooting, choose one-shoot. In the
M and Multi mode, the master unit only sends
triggering signals to the slave unit, which is suitable
for one person photography for the advantage of
power saving.
Multi-shoots: When shooting, choose multi-shoots,
and the master unit will send parameters and
triggering signals to the slave unit, which is suitable
for multi person photography. However, this function
consumes power quickly.
APP: Only send triggering signal when camera is
shooting (control the flash's parameters by
smartphone APP).
C.Fn Ver 9.2
GROUP
LCD
SYNC
APP
CLEAR
SHOOT
Setting Signs
ON
OFF
ON
OFF
1/128
1/256
12sec
OFF
ON
IN
OUT
5 (A-E)
16 (O-F)
-3-+3
Settings and Description
ON
OFF
ON
OFF
The minimum output is 1/128
The minimum output is 1/256
Off in 12 seconds
Always off
Always lighting
Enable XProC to trigger flash
Export triggering signal to trigger other remote control
and flash
5 groups (A-E)
16 groups (0-F); 16 groups when the receiver end is
studio flash, which can only be set to M mode in this state
The contrast ration can be set as integral number from
-3 to +3
Custom Function
STBY
BEEP
MIN
LIGHT
SYNC
GROUP
LCD
Function
Sleep
Beeper
Power output
value
Backlighting
time
Sync cord jack
Group
Contrast ratio
of LCD panel
Setting the Flash Trigger Setting the Flash Trigger
- 42 -- 41 -
Setting Signs
One-shoot
Full-shoot
APP
0-30m
1-100m
OFF
01-99
200j
360j
600j
Custom Function
SHOOT
DIST
ID
TCM
Function
APP
Triggering
distance
Wireless ID
TCM transform
function
Settings and Description
Only send triggering signals in the M & Multi mode when
camera is shooting
Send parameters and triggering signal when camera
is shooting(suitable for multi person photography)
Only send triggering signal when camera is shooting
(control the flash’s parameters by smartphone APP)
0-30m triggering
1-100m triggering
Off
Choose any figure from 01-99 (the current version
flashes cannot use this function temporarily)
TT685/V860II series
AD200
AD360II
AD600
The power output values in the
M mode which are transformed
from TTL mode, being subjected
to the master flash when mixing
Compatible Flash Models
Receiver
--
X1R-C
XTR-16
XTR-16S
Flash
AD600 series/AD360II series/AD200/
V860II series/V850II/TT685 series
TT600/TT350C
QuickerII series/QTII/SK II series
DP II series/GSII
600EX-RT/580EXII/580EX/430EXII
V860C
AD360/AR400
Quicker series/SK series/DP series/
GT/GS series/Smart flash series
V860C
V850
Note
As there are so many camera flashes in
the market which are compatible with
Canon speedlites, we do not test one by one.
The flashes with Godox wireless USB port
Can only be triggered
Transmitter
XProC
Note: The range of support functions: the functions that are both owned by XProC and flash.
Compatible Flash ModelsSetting the Flash Trigger
- 44 -
- 43 -
Compatible Flash Models
The relationship of XT wireless system and X1 wireless system:
XT-16
(Code Switch)
X1
(Display Screen)
ON
CH01 CH02 CH03 CH04 CH05 CH06 CH07 CH08
X1
(Display Screen) CH09 CH10 CH11 CH12 CH13 CH14 CH15 CH16
ON O N ON ON ON O N ON
XT-16
(Code Switch)
ON O N ON ON ON O N ON ON
1Dx Mark II 1Dx 5Ds/5Dsr 5DⅣ 5D Mark III 5D Mark II 5D
7D Mark II 7D 6D 80D 70D 60D 50D
40D 30D 750D/760D 700D 650D 600D 550D
500D 450D 400D Digital 350D DIGITAL 100D 1200D 1000D
1100D M5 M3
1. This table only lists the tested camera models, not all Canon EOS series cameras. For the compatibility
of other camera models, a self-test is recommended.
2. Rights to modify this table are retained.
3. The cameras which are released before 2012 do not have TTL mode in their D and E group.
This flash trigger can be used on the following Canon EOS series camera models:
Model
Compatible cameras
Power supply
Flash Exposure Control
TTL autoflash
Manual flash
Stroboscopic flash
Function
High-speed sync
Second-curtain sync
Flash exposure
compensation
Flash exposure lock
Focus assist
Modeling lamp
Beeper
Wireless setting
ZOOM setting
TCM function
XProC
Canon EOS cameras (E-TTL II autoflash)
Support for the cameras that have PC sync socket.
2*AA batteries
E-TTL II
Yes
Yes
Yes
Yes
Yes, ±3 stops in 1/3 stop increments
Yes
Yes
Control the modeling lamp by the flash trigger
Control the beeper by the flash trigger
The receiver end can control the camera shooting through the
2.5mm sync cord jack
Adjust the ZOOM value by the transmitter
Transform the TTL shooting value into the output value in the M node
Technical Data
Compatible Camera Models
- 46 -
- 45 -
XProC
Upgrade through the Type-C USB port
Settings will be stored 2 seconds after last operation
and recover after a restart
0-100m
2.4G
MSK
32
01-99
16
Large LCD panel, backlighting ON or OFF
90x58x50mm/80g
2413.0MHz-2464.5MHz
5dbm
Restore Factory Settings
Synchronously press the two function button in the middle, and the restore factory settings are
finished until the “RESET” is displayed on the LCD panel.
Technical Data Attentions
1. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly
and Power Switch is turned on. Check if the transmitter and the receiver are set to
the same channel, if the hotshoe mount or connection cable is well connected, or if
the flash triggers are set to the correct mode.
2. Camera shoots but does not focus. Check if the focus mode of the camera or lens is
set to MF. If so, set it to AF.
3. Signal disturbance or shooting interference. Change a different channel on the
device.
4. Operating distance limited or flash missing. Check if batteries are exhausted. If so,
change them.
Avoid sudden drops. The device may fail to work after strong shocks, impacts, or
excess stress.
Keep dry. The product isn’t water-proof. Malfunction, rust, and corrosion may occur
and go beyond repair if soaked in water or exposed to high humidity.
Avoid sudden temperature changes. Condensation happens if sudden
temperature changes such as the circumstance when taking the transceiver out of a
building with higher temperature to outside in winter. Please put the transceiver in a
handbag or plastic bag beforehand.
Keep away from strong magnetic field. The strong static or magnetic field
produced by devices such as radio transmitters leads to malfunction.
Caring for Flash Trigger
- 48 -
- 47 -
Model
Firmware upgrade
Memory function
Wireless Flash
Transmission range (approx.)
Built-in wireless
Modulation mode
Channel
Wireless ID
Group
Other
Display
Dimension/Weight
2.4G Wireless Frequency Range
Max. Transmitting Power of 2.4G Wireless
Firmware Upgrade
This flash trigger supports firmware upgrade through the Type-CUSB port. Update information will
be released on our official website.
USB connection line is not included in this product. As the USB port is a Type-C USB socket,
please use Type-C USB connection line.
As the firmware upgrade needs the support of Godox G2 software, please download and install
the "Godox G2 firmware upgrade software" before upgrading. Then, choose the related
firmware file.
As the products needs to do firmware upgrade, please refer to instruction manual
of the newest electric version as final.
A. This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
B. Warning: Changes or modifications to this unit not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
C. NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC statement

Navigation menu